Radar Vectors
Advisory Circular Cancelled Issued Sep 28, 2012 AAS-100 322 pages Copy saved Nov 18, 2026

AC 150/5300-13A Airport Design

Contains the Federal Aviation Administration’s (FAA) standards and recommendations for the geometric layout and engineering design of runways, taxiways, aprons, and other facilities at civil airports.This substantial revision fully incorporates all previous changes to AC 150/5300-13 as well as new standards and technical requirements.

This document is no longer current. Cancelled by 150/5300-13B. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Airport Design Date: 2/26/2014

Initiated by: AAS-100

AC No: AC 150/5300-13A

Change: 1

1. What is the purpose of this advisory circular (AC)?

This Change primarily includes updates to the standards for Taxiway Fillet Design.

2. What are the principal changes in this Change?

Text revised in this Change is indicated by vertical bars in the margins of the attached consolidated AC. We have not indicated the change number or change date in the headers of revised pages. See the Record of Changes, discussed below, for a log of all revisions made in this Change. Principal changes include:

a. New Approach and Departure Reference Code (APRC and DPRC) designations replace Runway Reference Code (RRC).

b. Expanded Taxiway Fillet information, including a new Appendix 8, Taxiway Fillet Design, discussing description, dimensions and transitions.

c. Adjusted TDG limits, with associated changes to fillet dimensions.

d. Moved Figure 4-1 to Chapter 1 where it is first referenced.

e. Combined Tables 3-4 and 3-5 to form Standards for Instrument Approach Procedures.

f. This Change contains minor editorial corrections.

g. This Change incorporates a Record of Changes at the end of the consolidated AC. We will log all substantive revisions made in this and subsequent Changes in this Record.

h. This Change also incorporates revisions described in the Errata Sheets for both the original release and the Change release.

Michael J. O’Donnell Director of Airport Safety and Standards

AC 150/5300-13A CHG 1 2/26/2014

ii

Page intentionally left blank.

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Consolidated AC includes Change 1

Subject: Airport Design Date: 9/28/2012

Initiated by: AAS-100

AC No: AC 150/5300-13A

Change:

1. What is the purpose of this advisory circular (AC)?

This AC contains the Federal Aviation Administration’s (FAA) standards and recommendations for airport design.

2. Does this AC cancel any prior ACs?

AC 150/5300-13, Airport Design, dated September 29, 1989, is canceled.

3. To whom does this AC apply?

The FAA recommends the standards and recommendations in this AC for use in the design of civil airports. In general, use of this AC is not mandatory. The standards and recommendations contained in this AC may be used by certificated airports to satisfy specific requirements of Title 14 Code of Federal Regulations (CFR) Part 139, Certification of Airports, subparts C (Airport Certification Manual) and D (Operations). Use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and/or with revenue from the Passenger Facility Charges (PFC) Program. See Grant Assurance No. 34, Policies, Standards, and Specifications, and PFC Assurance No. 9, Standards and Specifications.

4. Are there any related documents?

Related documents to this AC are indicated in paragraph 108.

5. What are the principal changes in this AC?

This AC was substantially revised to fully incorporate all previous Changes to AC 150/5300-13, as well as new standards and technical requirements. This document was reformatted to simplify and clarify the FAA’s airport design standards and improve readability. Users should review the entire document to familiarize themselves with the new format. Additional principal changes include:

a. A new Runway Design Code (RDC) designation

ii

b. An expanded discussion on Declared Distances

c. A new Runway Reference Code (RRC) designation

d. An update to the Runway Protection Zone (RPZ) standards

e. New Taxiway Design Group (TDG) categories for fillet design

f. Guidance for intersecting and non-intersecting runway geometry

g. Expanded discussion on Runway Incursion Prevention geometry for new construction

h. Consolidation of numerous design tables into one interactive Runway Design Requirements Matrix (Table 3-8)

i. Consolidation of several Appendices in to the runway and taxiway design chapters

j. A new Aircraft Characteristics Database and a refresh to all listed Appendices

Hyperlinks (allowing the reader to access documents located on the internet and to maneuver within this document) are provided throughout this document and are identified with underlined text. When navigating within this document, return to the previously viewed page by pressing the “ALT” and “” keys simultaneously.

Figures in this document are representations and are not to scale.

6. How are metrics represented?

Throughout this AC, customary English units will be used followed with “soft” (rounded) conversion to metric units. The English units govern.

7. How can I get this and other FAA publications?

You can view a list of all ACs at http://www.faa.gov/regulations_policies/advisory_circulars/. You can view the Federal Aviation Regulations at http://www.faa.gov/regulations_policies/faa_regulations/. Michael J. O’Donnell Director of Airport Safety and Standards

iii

TABLE OF CONTENTS

Chapter 1. Introduction … 1

101. Purpose … 1 102. Definitions … 2 103. Roles of Federal, State and Local governments … 10 104. Airport operator responsibilities … 11 105. Planning … 12 106. Airport Layout Plan (ALP) … 15 107. Collection, processing and publication of airport data … 15 108. Related Advisory Circulars (ACs), Orders, and Federal regulations … 17 109. to 199. Reserved … 30

Chapter 2. Design Process … 31

201. General … 31 202. Design aircraft … 33 203. Runway incursions … 34 204. Airport design standards and the environmental process … 34 205. Planned visibility minimums for instrument procedures … 35 206. Airport Traffic Control Tower (ATCT) siting … 36 207. Airport Reference Point (ARP) … 37 208. Heliports/helipads … 37 209. Other aeronautical uses on airports … 37 210. Drainage considerations … 37 211. Security of airports … 39 212. Pavement strength and design … 40 213. Location of on-airfield facilities … 41 214. to 299. Reserved … 41

Chapter 3. Runway Design … 43

301. Introduction … 43 302. Runway design concepts … 43 303. Runway end siting requirements … 46 304. Runway geometry … 54 305. Runway line of sight requirements … 57 306. Object clearing … 58 307. Runway Safety Area (RSA) / Engineered Materials Arresting Systems (EMAS).

… 59 308. Obstacle Free Zone (OFZ) … 62 309. Runway Object Free Area (ROFA) … 69 310. Runway Protection Zone (RPZ) … 71 311. Clearway standards … 76 312. Stopway standards … 77

iv

313. Surface gradient … 77 314. Turf runways … 82 315. Marking and lighting … 85 316. Parallel runway separation requirements … 86 317. Approach procedures … 87 318. Aircraft Rescue and Fire Fighting (ARFF) access … 91 319. Jet blast … 91 320. Runway design requirements matrix … 92 321. On-airport farming … 92 322. Declared distances … 96 323. Approach and Departure Reference Codes … 111 324. to 399. Reserved … 113

Chapter 4. Taxiway and Taxilane Design … 115

401. General … 115 402. Taxiway definitions … 121 403. Taxiway/taxilane width … 122 404. Taxiway/taxilane clearance requirements … 122 405. Parallel taxiways … 129 406. Curves and intersections … 131 407. Runway/taxiway intersections … 140 408. Entrance taxiways … 140 409. Exit taxiways … 143 410. Bypass taxiways … 148 411. Crossover taxiways … 149 412. Holding bays for runway ends … 152 413. Taxiway turnarounds … 155 414. Apron taxiways and taxilanes … 155 415. End-Around Taxiways (EAT) … 156 416. Aligned taxiways prohibited … 159 417. Taxiway shoulders … 159 418. Surface gradient and Line Of Sight (LOS) … 161 419. Markings/lighting/signs … 162 420. Islands … 162 421. Taxiway bridges … 162 422. Jet blast … 163 423. to 499. Reserved … 163

Chapter 5. Aprons … 165

501. Background … 165 502. Apron types … 165 503. Apron layout and runway incursion prevention … 165 504. Apron design … 166 505. Fueling … 168 506. Object clearance … 169

v

507. Deicing facilities … 169 508. Surface gradients … 169 509. Drainage … 169 510. Marking and lighting … 169 511. Pavement design … 170 512. Jet blast … 170 513. Airport Traffic Control Tower (ATCT) visibility / Line Of Sight (LOS) … 170 514. Apron service roads … 170 515. to 599. Reserved … 171

Chapter 6. Navigation Aids (NAVAIDs) and On-airport Air Traffic Control Facilities (ATC-F) … 173

601. Background … 173 602. Introduction and purpose … 173 603. Federally owned and non-federally owned NAVAIDs … 175 604. Siting criteria/land requirements … 175 605. NAVAIDs as obstacles … 176 606. Physical security … 178 607. Maintenance access … 181 608. Electrical power … 181 609. Cable protection … 181 610. Cable loop system … 181 611. Communication and power cable trenches … 181 612. Facilities … 182 613. Towers and elevated structures … 182 614. Air Traffic Organization (ATO) – Orders and Notices … 182 615. Decommissioned facilities … 182 616. Airport Traffic Control Tower (ATCT) … 183 617. Remote Transmitter/Receiver (RTR) and Remote Communications Outlet (RCO).

… 184 618. Airport Surveillance Radar (ASR) … 184 619. Precision Runway Monitor (PRM) … 185 620. Airport Surface Detection Equipment (ASDE) … 186 621. Approach Lighting System (ALS) … 186 622. Approach Lead-In Lighting System (LDIN) … 193 623. Runway End Identifier Lighting (REIL) … 194 624. Airport rotating beacons … 196 625. Precision Approach Path Indicator (PAPI) … 196 626. Instrument Landing System (ILS) … 198 627. Distance Measuring Equipment (DME) … 201 628. Runway Visual Range (RVR) … 202 629. Very High Frequency Omnidirectional Range (VOR) … 203 630. Non-Directional Beacon (NDB) … 206 631. Segmented circles and wind cones … 206 632. Automated Surface Observing System (ASOS) and Automated Weather

Observing System (AWOS) … 207

vi

633. Weather Camera (WCAM) … 207 634. Wind Equipment F-400 (WEF) … 208 635. Low Level Windshear Alert System (LLWAS) … 209 636. Runway Status Lights (RWSL) … 209 637. to 699. Reserved … 209

Chapter 7. Airfield Bridges and Tunnels … 211

701. General … 211 702. Siting guidelines … 213 703. Dimensional criteria … 214 704. Load considerations … 214 705. Marking and lighting … 215 706. Other considerations … 215 707. Storm water structures … 218 708. to 799. Reserved … 218

Appendix 1. Aircraft Characteristics … 219

A1-1. Basic aircraft characteristics … 219 A1-2. Background … 221 A1-3. Aircraft arranged by aircraft manufacturer, and Runway Design Code (RDC). 221

Appendix 2. Wind Analysis … 231

A2-1. Objective … 231 A2-2. Crosswinds … 232 A2-3. Allowable crosswind components … 232 A2-4. Coverage and orientation of runways … 232 A2-5. Assembling wind data … 232 A2-6. Data source … 233 A2-7. Analyzing wind data … 236 A2-8. Conclusions … 239 A2-9. Assumptions … 239 A2-10. Automated wind analysis tools … 239

Appendix 3. The Effects and Treatment of Jet Blast … 241

A3-1. Introduction … 241 A3-2. Jet blast effects … 241 A3-3. Jet engine exhaust velocity and temperature … 241 A3-4. Blast fences … 242 A3-5. Shoulders and blast pads … 242 A3-6. Aircraft parking layout and jet blast effect(s) … 243

Appendix 4. End-Around Taxiway (EAT) Screens … 247

A4-1. Screen sizing … 247

vii

A4-2. Screen construction … 248

Appendix 5. General Aviation Aprons and Hangars … 257

A5-1. Background … 257 A5-2. General aviation apron … 257 A5-3. Wash pads … 258 A5-4. Fueling … 258 A5-5. Object clearance … 258 A5-6. Surface gradients … 258 A5-7. Drainage … 260 A5-8. Marking and lighting … 260 A5-9. Hangars … 260

Appendix 6. Compass Calibration Pad … 263

A6-1. Purpose … 263 A6-2. Background … 263 A6-3. Design of compass calibration pad … 263 A6-4. Location of compass calibration pad … 266 A6-5. Construction of compass calibration pad … 267

Appendix 7. Runway Design Standards Matrix … 269

Appendix 8. Taxiway Fillet Design … 283

A8-1. Description … 283 A8-2. Dimensions … 283 A8-3. Transitions … 284

Appendix 9. Acronyms … 295

Appendix 10. Index … 301

Record of Changes … 305

LIST OF FIGURES Figure 1-1. Taxiway Design Groups (TDGs) … 15 Figure 3-1. Runway ends … 46 Figure 3-2. Threshold siting based on approach slope … 49 Figure 3-3. Approach slopes – with offset approach course … 51 Figure 3-4. Departure surface for instrument runways (40:1) … 53 Figure 3-5. Runway Safety Area (RSA) … 55 Figure 3-6. Intersecting runways … 56 Figure 3-7. Runway visibility zone … 58

viii

Figure 3-8. Percent of aircraft overrun versus distance beyond the runway end … 60 Figure 3-9. Obstacle Free Zone (OFZ) for visual runways and runways with not lower than 3/4

statute mile (1.2 km) approach visibility minimums … 63 Figure 3-10. OFZ for operations on runways by small aircraft with lower than 3/4 statute mile

(1.2 km) approach visibility minimums … 64 Figure 3-11. OFZ for operations on runways by large aircraft with lower than 3/4 statute mile

(1.2 km) approach visibility minimums … 64 Figure 3-12. OFZ for operations on runways by large aircraft with lower than 3/4 statute mile

Figure 1-1: picture of page 9Figure 1-1 · page 9
Picture of the page from the copy saved here

(1.2 km) approach visibility minimums and displaced threshold … 65 Figure 3-13. Sectional views of the OFZ … 66 Figure 3-14. Precision Obstacle Free Zone (POFZ) – no displaced threshold … 68 Figure 3-15. POFZ – displaced threshold … 70 Figure 3-16. Runway Protection Zone (RPZ), Runway Object Free Area (ROFA) and Runway

Safety Area (RSA) … 72 Figure 3-17. Runway with all declared distances equal to the runway length … 74 Figure 3-18. Approach and departure RPZs where the Takeoff Run Available (TORA) is less

than the Takeoff Distance Available (TODA) … 75 Figure 3-19. Clearway … 76 Figure 3-20. Stopway … 78 Figure 3-21. Longitudinal grade limitations for aircraft approach categories A and B … 79 Figure 3-22. Longitudinal grade limitations for aircraft approach categories C, D, and E … 81 Figure 3-23. Transverse grade limitations … 83 Figure 3-24. RSA grade limitations beyond 200 feet (61 m) from the runway end … 84 Figure 3-25. Parallel runway separation, simultaneous radar controlled approach – staggered

Figure 3-13: picture of page 10Figure 3-13 · page 10
Picture of the page from the copy saved here

threshold … 88 Figure 3-26. Typical airport layout … 95 Figure 3-27. Location of start of Accelerate-Stop Distance Available (ASDA), TODA, and

TORA … 98 Figure 3-28. Normal location of departure end of TORA … 99 Figure 3-29. Departure end of TORA based on departure RPZ located to mitigate unacceptable

incompatible land use … 99 Figure 3-30. TODA shortened to mitigate penetration to the departure surface resulting in

shortened TORA … 100 Figure 3-31. TODA extended by use of a clearway, shortened TORA … 101 Figure 3-32. Normal location of departure end of TODA (no clearway) … 102 Figure 3-33. TODA extended by use of a clearway, normal TORA … 103 Figure 3-34. Normal location of stop end of ASDA and Landing Distance Available (LDA) ...104 Figure 3-35. Stop end of ASDA and LDA located to provide additional RSA … 105 Figure 3-36. Stop end of ASDA and LDA located to provide additional Runway Object Free

Figure 3-26: picture of page 10Figure 3-26 · page 10
Picture of the page from the copy saved here

Area (ROFA) … 106 Figure 3-37. Stop end of ASDA located based on use of a stopway … 107 Figure 3-38. Normal start of LDA … 108 Figure 3-39. Start of LDA at displaced threshold based on Threshold Siting Surface (TSS) … 109 Figure 3-40. Start of LDA at displaced threshold based on approach RPZ located to mitigate

unacceptable incompatible land use … 109 Figure 3-41. Start of LDA at displaced threshold located to provide additional RSA … 110

ix

Figure 3-37: picture of page 10Figure 3-37 · page 10
Picture of the page from the copy saved here

Figure 3-42. Start of LDA at displaced threshold located to provide additional ROFA … 111 Figure 4-1. Three-node taxiway intersection … 116 Figure 4-2. Not recommended taxiway design … 118 Figure 4-3. Proper taxiway design … 118 Figure 4-4. Taxiway designs that are not recommended (examples a, b, c, d) … 119 Figure 4-5. Taxiway designs that are not recommended (examples e, f, g) … 120 Figure 4-6. Taxiway Edge Safety Margin (TESM) on straight segment … 121 Figure 4-7. Wingtip clearance - parallel taxiways … 123 Figure 4-8. Wingtip clearance from taxiway … 125 Figure 4-9. Wingtip clearance from taxilane … 126 Figure 4-10. Wingtip clearance from apron taxiway … 127 Figure 4-11. TSA and TOFA at taxiway intersections … 128 Figure 4-12. Parallel taxiways … 130 Figure 4-13. Taxiway turn - 90 degree delta … 133 Figure 4-14. Taxiway turn - less than 90 degree delta … 134 Figure 4-15. Taxiway turn - greater than 90 degree delta … 134 Figure 4-16. Key MGW-CMG combinations for modeling aircraft movements … 139 Figure 4-17. Entrance taxiway … 141 Figure 4-18.

Figure 3-42: picture of page 11Figure 3-42 · page 11
Picture of the page from the copy saved here

High speed exit for TDG-5 … 144 Figure 4-19. Right-angled exit taxiway … 145 Figure 4-20. Poor design of high speed exits … 146 Figure 4-21. Proper design of high speed exits … 147 Figure 4-22. Bypass taxiway … 148 Figure 4-23. Crossover taxiway where direction reversal is needed based on TDG … 150 Figure 4-24. Crossover taxiway where direction reversal is necessary based on ADG … 150 Figure 4-25. Crossover taxiway without direction reversal between taxiways … 152 Figure 4-26. Typical holding bay configuration … 153 Figure 4-27. Holding bay – not recommended design … 154 Figure 4-28. Poor holding bay design … 154 Figure 4-29. Taxiway turnaround … 155 Figure 4-30. End-Around Taxiway (EAT) – ADG-II … 157 Figure 4-31. EAT – ADG-III … 158 Figure 4-32. Aligned taxiway … 160 Figure 4-33. Taxiway transverse gradients … 162 Figure 6-1. Typical Communications, Navigation, Surveillance and Weather (CNSW) … 174 Figure 6-2. Two frangible connections … 178 Figure 6-3. Airport Traffic Control Tower (ATCT) facility … 183 Figure 6-4.

Figure 4-19: picture of page 11Figure 4-19 · page 11
Picture of the page from the copy saved here

Remote Transmitter/Receiver (RTR) communication facility … 184 Figure 6-5. Airport Surveillance Radar (ASR) steel tower (17 feet [5 m] high) … 185 Figure 6-6. Precision Runway Monitor (PRM) facility … 186 Figure 6-7. Approach Lighting System (ALS) with Sequenced Flashers II (ALSF-2) … 188 Figure 6-8. Simplified Short Approach Light System with Runway Alignment (SSALR) … 189 Figure 6-9. Medium Intensity Approach Lighting System (MALS) with Runway Alignment

Indicator Lights (MALSR) … 190 Figure 6-10. MALSR facility … 191 Figure 6-11. MALS … 191

x

Figure 6-5: picture of page 11Figure 6-5 · page 11
Picture of the page from the copy saved here

Figure 6-12. MALS with Sequenced Flashers (MALSF) … 192 Figure 6-13. Omnidirectional Airport Lighting System (ODALS) … 192 Figure 6-14. Lead-in Lighting System (LDIN) … 193 Figure 6-15. Approach LDIN facility … 194 Figure 6-16. Runway End Identifier Lighting (REIL) … 195 Figure 6-17. REIL … 195 Figure 6-18. Precision Approach Path Indicator (PAPI) … 197 Figure 6-19. PAPI light boxes … 197 Figure 6-20. Instrument Landing System (ILS) Localizer (LOC) siting and critical area … 198 Figure 6-21. LOC 8-antenna array … 199 Figure 6-22. LOC 14-antenna array … 200 Figure 6-23. Glideslope (GS) siting and critical area … 200 Figure 6-24. GS antenna and equipment shelter … 201 Figure 6-25. Distance Measuring Equipment (DME) antenna … 201 Figure 6-26. Touchdown Runway Visual Range (RVR) … 202 Figure 6-27. Enroute VHF Omnidirectional Range (VOR) facility … 204 Figure 6-28. Terminal VOR (TVOR) facility … 204 Figure 6-29. TVOR installation … 205 Figure 6-30. TVOR clearances … 205 Figure 6-31. Non-Directional Beacon (NDB) facility … 206 Figure 6-32. Segmented circle and wind cone … 206 Figure 6-33.

Figure 6-12: picture of page 12Figure 6-12 · page 12
Picture of the page from the copy saved here

Automated Surface Observing System (ASOS) weather sensors suite … 207 Figure 6-34. Weather Camera (WCAM) pole … 208 Figure 6-35. Weather equipment sensor pole … 208 Figure 6-36. Low Level Windshear Alert System (LLWAS) sensor pole … 209 Figure 7-1. Tunnel under a runway and parallel taxiway … 211 Figure 7-2. Cross-section of a tunnel under a runway and taxiway … 212 Figure 7-3. Airfield bridge … 213 Figure 7-4. Shoulder markings for taxiway bridges … 216 Figure 7-5. Example of a structural deck with lighted depressed roadway … 217 Figure A1-1. Typical dimensions of large aircraft … 219 Figure A1-2. Typical dimensions of small aircraft … 220 Figure A2-1. Wind vector diagram … 231 Figure A2-2. Blank windrose showing direction and divisions … 234 Figure A2-3. Completed windrose using Figure A2-1 data … 235 Figure A2-4. Windrose analysis … 238 Figure A4-1. End-Around Taxiway (EAT) screen horizontal geometry … 247 Figure A4-2. Visual screen width calculation … 248 Figure A4-3. EAT screen vertical dimension calculation … 249 Figure A4-4.

Figure 6-34: picture of page 12Figure 6-34 · page 12
Picture of the page from the copy saved here

Stop end of the runway/EAT elevation difference … 249 Figure A4-5. Examples of mounting screen to vertical column … 250 Figure A4-6. Examples of panel layout for 13-foot (4 m) high screen … 252 Figure A4-7. Diagonal stripe orientation … 253 Figure A5-1. Tiedown layouts … 259 Figure A6-1. Compass calibration pad marking layout … 264 Figure A6-2. Typical compass calibration pad … 265

xi

Figure A8-1. Filet design example … 283 Figure A8-2. Angle of intersection (delta) … 285 Figure A8-3. Steering angle of no more than 50 degrees … 286 Figure A8-4. Track of the main gear is modeled, offset by the TESM … 287 Figure A8-5. Minimize excess pavement while providing the required TESM … 288 Figure A8-6. Pavement edge (main gear track + TESM) offset by 6 inches (15 cm) … 289 Figure A8-7. Detail of Figure A8-6 … 290 Figure A8-8. Tapers selected to minimize excess pavement while considering constructability291 Figure A8-9. Radius of outer pavement edge determined based on the minimum CMG and

maximum MGW in the TDG … 292 Figure A8-10. Dimensions applied to the design … 293

LIST OF TABLES Table 1-1. Aircraft Approach Category (AAC) … 13 Table 1-2. Airplane Design Group (ADG) … 14 Table 1-3. Visibility minimums … 14 Table 2-1. Changes in airport design standards associated with an upgrade in the first two

components (Aircraft Approach Category [AAC] and Airplane Design Group [ADG]) of the Runway Design Code (RDC) … 32 Table 2-2. Changes in airport design standards associated with lowering the third component

(approach visibility minimums) of the Runway Design Code (RDC) … 33 Table 2-3. Aircraft characteristics and design components … 34 Table 3-1. Allowable crosswind component per Runway Design Code (RDC) … 44 Table 3-2. Approach/departure standards table … 50 Table 3-3. Transverse grades … 69 Table 3-4. Standards for Instrument Approach Procedures … 90 Table 3-5. Runway design standards matrix … 93 Table 3-6. Runway to taxiway separation for reverse turns from a high-speed exit based on

Taxiway Design Group (TDG) … 94 Table 3-7. Approach Reference Code (APRC) … 112 Table 3-8. Departure Reference Code (DPRC) … 113 Table 4-1. Design standards based on Airplane Design Group (ADG) … 124 Table 4-2. Design standards based on Taxiway Design Group (TDG) … 124 Table 4-3. Standard intersection details for TDG 1A … 135 Table 4-4. Standard intersection details for TDG 1B … 135 Table 4-5. Standard intersection details for TDG 2 … 136 Table 4-6. Standard intersection details for TDG 3 … 136 Table 4-7. Standard intersection details for TDG 4 … 137 Table 4-8. Standard intersection details for TDG 5 … 137 Table 4-9. Standard intersection details for TDG 6 … 138 Table 4-10. Standard intersection details for TDG 7 … 138 Table 4-11. MGW-CMG combinations … 139 Table 4-12. Dimensions for runway entrance/exit taxiways (where the two 90-degree turns are

nonstandard) … 142 Table 4-13. Exit taxiway cumulative utilization percentages … 147

xii

Table 4-14. Crossover taxiways with direction reversal between taxiways based on TDG … 149 Table 4-15. Crossover taxiways with direction reversal between taxiways based on ADG … 151 Table 6-1. Fixed-by-function designation for NAVAID and Air Traffic Control (ATC) facilities

for Runway Safety Area (RSA) and Runway Object Free Area (ROFA) … 177 Table 6-2. List of NAVAID facility type … 179 Table 6-3. Surveillance facility type … 180 Table 6-4. Communications facility type … 180 Table 6-5. Weather detection facility type … 180 Table A1-1. Aircraft characteristics database – sorted by aircraft manufacturer/model … 221 Table A2-1. Standard wind analysis results for ALL_WEATHER … 237 Table A4-1. Aircraft characteristics … 249 Table A4-2. International Committee of Illumination (CIE) chromaticity coordinate limits … 253 Table A4-3. Minimum coefficient of retroreflection candelas/foot candle/square

foot/candelas/lux/square meter … 254 Table A4-4. Visual screen panel wind loads … 254 Table A7-1. Runway design standards matrix, A/B-I Small Aircraft … 269 Table A7-2. Runway design standards matrix, A/B - I … 270 Table A7-3. Runway design standards matrix, A/B – II Small Aircraft … 271 Table A7-4. Runway design standards matrix, A/B – II … 272 Table A7-5. Runway design standards matrix, A/B - III … 273 Table A7-6. Runway design standards matrix, A/B - IV … 274 Table A7-7. Runway design standards matrix, C/D/E - I … 275 Table A7-8. Runway design standards matrix, C/D/E - II … 276 Table A7-9. Runway design standards matrix, C/D/E - III … 277 Table A7-10. Runway design standards matrix, C/D/E - IV … 278 Table A7-11. Runway design standards matrix, C/D/E - V … 279 Table A7-12. Runway design standards matrix, C/D/E - VI … 280

Chapter 1. Introduction › 101. Purpose.

Chapter 1. Introduction

101. Purpose.

a. General. Title 49 United States Code (USC), Chapter 401, General Provisions, Section (§) 40101(d) states in part, “[T]he [FAA] Administrator shall consider the following matters, among others, as being in the public interest: (1) assigning, maintaining, and enhancing safety and security as the highest priorities in air commerce, (2) regulating air commerce in a way that best promotes safety and fulfills national defense requirements, (3) encouraging and developing civil aeronautics, including new aviation technology.” This public charge, in effect, requires the development and maintenance of a national system of safe, delay-free, and costeffective airports. The use of the standards and recommendations contained in this publication in the design of airports supports this public charge. In addition, Title 49 USC Chapter 471, Airport Development, § 47101, states that “[i]t is the policy of the United States that the safe operation of the airport and airway system is the highest aviation priority.” The policy emphasizes, in part, airport construction and improvement projects that:

(1) Increase safety

(2) Increase capacity to accommodate passenger and cargo and decrease delays

(3) Comply with federal environmental standards (see also Order 5050.4, National Environmental Policy Act [NEPA] Implementing Instructions for Airport Projects).

(4) Encourage innovative technologies that promote safety, capacity, and efficiency.

The use of the standards and recommendations contained in this advisory circular (AC) support this policy.

These standards and recommendations, however, do not limit or regulate the operations of aircraft.

b. New airports. These standards and recommendations represent the most effective national approach for meeting the long-term aviation demand in a manner that is consistent with national policy. Safety is the highest priority. The airport design standards in this AC are intended to identify the design elements needed to maintain safety and efficiency according to national policy.

c. Existing airports. Every effort should be made to bring an airport up to current standards. It may not, however, be feasible to meet all current standards at existing airports, and in the case of federal assistance programs, funding of improvements may be subject to FAA criteria. In those cases, consultation with the appropriate offices of the FAA Office of Airports and Flight Standards Service will identify any applicable FAA funding criteria and/or adjustments to operational procedures necessary to accommodate operations to the maximum extent while maintaining an acceptable level of safety. For non-standard conditions associated

Chapter 1. Introduction › 102. Definitions.

with such projects, the FAA may consider alternative means of ensuring an acceptable level of safety. For further information regarding a modification of standards, refer to Order 5300.1, Modification to Agency Airport Design, Construction, and Equipment Standards.

d. Federal regulations and safety.

(1) Aircraft operations cannot be prevented, regulated, or controlled simply because the airport or runway does not meet the design standards for a particular aircraft type. For specific operational situations unique to the airport, consult with the FAA Flight Standards Service.

(2) Airports that have scheduled air carrier operations with more than nine passenger seats or unscheduled air carrier operations with more than 30 passenger seats are regulated by Title 14 Code of Federal Regulations (CFR) Part 139, Certification of Airports. Compliance with this AC may be used to demonstrate compliance with specific requirements of Part 139.

e. Design standards. The selection of the design aircraft, or group of aircraft characteristics, used to design or update an airport facility is a planning decision, beyond the scope of this AC. Thus, this AC does not consider such factors as:

(1) Airport ownership.

(2) Funding source used to establish, improve, or update the facility to meet anticipated needs.

(3) Service level designation in the National Plan of Integrated Airport Systems (NPIAS).

For additional information on the eligibility for federal funding, please refer to Order 5100.38, Airport Improvement Program Handbook.

102. Definitions.

The definitions in this paragraph are relevant to airport design standards.

a. Accelerate-Stop Distance Available (ASDA). See Declared Distances.

b. Air Traffic Control Facilities (ATC-F). Electronic equipment and buildings aiding air traffic control (ATC) – for communications, surveillance of aircraft including weather detection and advisory systems.

c. Aircraft. For this AC, the terms aircraft and airplane are synonymous, referring to all types of fixed-wing airplanes, including gliders. Powered lift (tilt-rotors) and helicopters are not included except where specifically noted.

d. Aircraft Approach Category (AAC). As specified in 14 CFR Part 97 § 97.3, Symbols and Terms Used in Procedures, a grouping of aircraft based on a reference landing

speed (VREF), if specified, or if VREF is not specified, 1.3 times stall speed (VSO) at the maximum certificated landing weight. VREF, VSO, and the maximum certificated landing weight are those values as established for the aircraft by the certification authority of the country of registry.

e. Airplane. A fixed-wing aircraft that is heavier than air, and is supported in flight by the dynamic reaction of the air against its wings (see Aircraft).

f. Airplane Design Group (ADG). A classification of aircraft based on wingspan and tail height. When the aircraft wingspan and tail height fall in different groups, the higher group is used.

g. Airport Elevation. The highest point on an airport’s usable runways expressed in feet above mean sea level (MSL).

h. Airport Layout Plan (ALP). A scaled drawing (or set of drawings), in either traditional or electronic form, of current and future airport facilities that provides a graphic representation of the existing and long-term development plan for the airport and demonstrates the preservation and continuity of safety, utility, and efficiency of the airport to the satisfaction of the FAA.

i. Airport Reference Code (ARC). An airport designation that signifies the airport’s highest Runway Design Code (RDC), minus the third (visibility) component of the RDC. The ARC is used for planning and design only and does not limit the aircraft that may be able to operate safely on the airport.

j. Airport Reference Point (ARP). The approximate geometric center of all usable runways at the airport.

k. Airport. An area of land that is used or intended to be used for the landing and takeoff of aircraft, and includes its buildings and facilities, if any.

l. Aligned Taxiway. A taxiway with its centerline aligned with a runway centerline. Sometimes referred to as an “inline taxiway.”

m. Approach Procedure with Vertical Guidance (APV). An Instrument Approach Procedure (IAP) providing both vertical and lateral electronic guidance.

n. Approach Reference Code (APRC). A code signifying the current operational capabilities of a runway and associated parallel taxiway with regard to landing operations.

o. Approach Surface Baseline (ASBL). A horizontal line tangent to the surface of the earth at the runway threshold aligned with the final approach course.

p. Blast Fence. A barrier used to divert or dissipate jet blast or propeller wash.

q. Blast Pad. A surface adjacent to the ends of runways provided to reduce the erosive effect of jet blast and propeller wash. A blast pad is not a stopway.

r. Building Restriction Line (BRL). A line that identifies suitable and unsuitable locations for buildings on airports.

s. Bypass Taxiway. A taxiway used to reduce aircraft queuing demand by providing multiple takeoff points.

t. Category-I (CAT-I). An instrument approach or approach and landing with a Height Above Threshold (HATh) or minimum descent altitude not lower than 200 ft (60 m) and with either a visibility not less than ½ statute mile (800m), or a runway visual range not less than 1800 ft (550m).

u. Category-II (CAT-II). An instrument approach or approach and landing with a Height Above Threshold (HATh) lower than 200 ft (60 m) but not lower than 100 ft (30 m) and a runway visual range not less than 1200 ft (350m).

v. Category-III (CAT-III). An instrument approach or approach and landing with a Height Above Threshold (HATh) lower than 100 ft (30m), or no HATh, or a runway visual range less than 1200 ft (350m).

w. Circling Approach. A maneuver initiated by the pilot to align the aircraft with a runway for landing when a straight-in landing from an instrument approach is not possible or is not desirable.

x. Clearway (CWY). A defined rectangular area beyond the end of a runway cleared or suitable for use in lieu of runway to satisfy takeoff distance requirements (see also Takeoff Distance Available [TODA]).

y. Cockpit to Main Gear Distance (CMG). The distance from the pilot’s eye to the main gear turn center.

z. Compass Calibration Pad. An airport facility used for calibrating an aircraft compass.

aa. Crossover Taxiway. A taxiway connecting two parallel taxiways (also referred to as a transverse taxiway).

bb. Decision Altitude (DA). A specified altitude on a vertically-guided approach at which a missed approach must be initiated if the required visual reference to continue the approach has not been established. DA is referenced to mean sea level (MSL).

cc. Declared Distances. The distances the airport owner declares available for a turbine powered aircraft's takeoff run, takeoff distance, accelerate-stop distance, and landing distance requirements. The distances are:

(1) Takeoff Run Available (TORA) – the runway length declared available and suitable for the ground run of an aircraft taking off;

(2) Takeoff Distance Available (TODA) – the TORA plus the length of any remaining runway or clearway beyond the far end of the TORA; the full length of TODA may need to be reduced because of obstacles in the departure area;

(3) Accelerate-Stop Distance Available (ASDA) – the runway plus stopway length declared available and suitable for the acceleration and deceleration of an aircraft aborting a takeoff; and

(4) Landing Distance Available (LDA) – the runway length declared available and suitable for landing an aircraft.

dd. Departure End of Runway (DER). The end of the runway that is opposite the landing threshold. It is sometimes referred to as the stop end of runway.

ee. Departure Reference Code (DPRC). A code signifying the current operational capabilities of a runway with regard to takeoff operations.

ff. Design Aircraft. An aircraft with characteristics that determine the application of airport design standards for a specific runway, taxiway, taxilane, apron, or other facility (such as Engineered Materials Arresting System [EMAS]). This aircraft can be a specific aircraft model or a composite of several aircraft using, expected, or intended to use the airport or part of the airport. (Also called “critical aircraft” or “critical design aircraft.”)

gg. Displaced Threshold. A threshold that is located at a point on the runway beyond the beginning of the runway.

hh. End-Around Taxiway (EAT). A taxiway crossing the extended centerline of a runway, which does not require specific clearance from air traffic control (ATC) to cross the extended centerline of the runway.

ii. Entrance Taxiway. A taxiway designed to be used by an aircraft entering a runway. Entrance taxiways may also be used to exit a runway.

jj. Exit Taxiway. A taxiway designed to be used by an aircraft only to exit a runway:

(1) Acute-Angled Exit Taxiway – A taxiway forming an angle less than 90 degrees from the runway centerline.

(2) High Speed Exit Taxiway – An acute-angled exit taxiway forming a 30 degree angle with the runway centerline, designed to allow an aircraft to exit a runway without having to decelerate to typical taxi speed.

kk. Fixed-By-Function Navigation Aid (NAVAID). An air navigation aid that must be positioned in a particular location in order to provide an essential benefit for aviation is fixed-byfunction. Table 6-1 gives fixed-by-function designations for various NAVAIDs as they relate to the Runway Safety Area (RSA) and Runway Object Free Area (ROFA). Some NAVAIDs that are not fixed-by-function in regard to the RSA or ROFA may be fixed-by-function in regard to the Runway Protection Zone (RPZ):

(1) Equipment shelters, junction boxes, transformers, and other appurtenances that support a fixed-by-function NAVAID are not fixed-by-function in regard to the RSA or ROFA unless operational requirements require them to be located near the NAVAID.

(2) Some NAVAIDs, such as localizers (LOCs), can provide beneficial performance even when they are not located at their optimal location. These NAVAIDs are not fixed-by-function in regard to the RSA or ROFA.

ll. Frangible. Retains its structural integrity and stiffness up to a designated maximum load, but on impact from a greater load, breaks, distorts, or yields in such a manner as to present the minimum hazard to aircraft. See AC 150/5220-23, Frangible Connections.

mm. General Aviation. All non-scheduled flights other than military conducted by non-commercial aircraft. General aviation covers local recreational flying to business transport that is not operating under the FAA regulations for commercial air carriers.

nn. Glide Path Angle (GPA). The GPA is the angle of the final approach descent path relative to the approach surface baseline.

oo. Glide Path Qualification Surface (GQS). An imaginary surface extending from the runway threshold along the runway centerline extended to the Decision Altitude (DA) point.

pp. Glideslope (GS). Equipment in an Instrument Landing System (ILS) that provides vertical guidance to landing aircraft.

qq. Hazard to Air Navigation. An existing or proposed object that the FAA, as a result of an aeronautical study, determines will have a substantial adverse effect upon the safe and efficient use of navigable airspace by aircraft, operation of air navigation facilities, or existing or potential airport capacity.

rr. Height Above Airport (HAA) . The height of the circling approach descent altitude (MDA) above the airport elevation.

ss. Height Above Threshold (HATh). The height of the Decision Altitude (DA) or Minimum Descent Altitude (MDA) above the threshold.

tt. Hot Spot. A location on an airport movement area with a history of potential risk of collision or runway incursion, and where heightened attention by pilots and drivers is necessary.

uu. Instrument Approach Procedure (IAP). A series of predetermined maneuvers for the orderly transfer of an aircraft under instrument flight conditions from the beginning of the initial approach to a landing or to a point from which a landing may be made visually. It is prescribed and approved for a specific airport by competent authority.

vv. Instrument departure runway. A runway identified by the airport operator, through the appropriate FAA Airports Office, to the FAA Regional Airspace Procedures Team intended primarily for instrument departures.

ww. Island. An unused paved or grassy area between taxiways, between runways, or between a taxiway and a runway. Paved islands are clearly marked as unusable, either by painting or the use of artificial turf.

xx. Joint-Use Airport. An airport owned by the United States that leases a portion of the airport to a person operating and airport specified under Part 139.

yy. Landing Distance Available (LDA). See Declared Distances.

zz. Large Aircraft. An aircraft with a maximum certificated takeoff weight of more than 12,500 lbs (5670 kg).

aaa. Low Impact Resistant (LIR) Support. A support designed to resist operational and environmental static loads and fail when subjected to a shock load such as that from a colliding aircraft.

bbb. Main Gear Width (MGW). The distance from the outer edge to outer edge of the widest set of main gear tires.

ccc. Minimum Descent Altitude (MDA). The lowest authorized altitude on an approach that does not have vertical guidance. MDA is referenced to mean sea level (MSL).

ddd. Modification to Standards. Any approved nonconformance to FAA standards, other than dimensional standards for Runway Safety Areas (RSAs), applicable to an airport design, construction, or equipment procurement project that is necessary to accommodate an unusual local condition for a specific project on a case-by-case basis while maintaining an acceptable level of safety. See Order 5300.1.

eee. Movement Area. The runways, taxiways, and other areas of an airport that are used for taxiing or hover taxiing, air taxiing, takeoff, and landing of aircraft including helicopters and tilt-rotors, exclusive of loading aprons and aircraft parking areas (reference Part 139).

fff. Navigation Aid (NAVAID). Electronic and visual air navigation aids, lights, signs, and associated supporting equipment.

ggg. Non-movement area. The areas of an airport that are used for taxiing or hover taxiing, or air taxiing aircraft including helicopters and tilt-rotors, but are not part of the movement area (i.e., the loading aprons and aircraft parking areas).

hhh. Non-Precision Approach (NPA). For the purposes of this AC, a straight-in instrument approach procedure that provides course guidance, with or without vertical path guidance, with visibility minimums not lower than 3/4 mile (4000 RVR).

iii. Non-Precision Runway. A runway (other than a precision runway) with at least one end having a non-precision approach procedure.

jjj. Object. Includes, but is not limited to, above ground structures, Navigational Aids (NAVAIDs), equipment, vehicles, natural growth, terrain, and parked or taxiing aircraft.

kkk. Object Free Area (OFA). An area centered on the ground on a runway, taxiway, or taxilane centerline provided to enhance the safety of aircraft operations by remaining clear of objects, except for objects that need to be located in the OFA for air navigation or aircraft ground maneuvering purposes.

lll. Obstacle. An existing object at a fixed geographical location or which may be expected at a fixed location within a prescribed area with reference to which vertical clearance is or must be provided during flight operation.

mmm. Obstacle Clearance Surface (OCS). An evaluation surface that defines the minimum required obstruction clearance for approach or departure procedures.

nnn. Obstacle Free Zone (OFZ). The OFZ is the three-dimensional airspace along the runway and extended runway centerline that is required to be clear of obstacles for protection for aircraft landing or taking off from the runway and for missed approaches.

ooo. Obstruction to Air Navigation. An object of greater height than any of the heights or surfaces presented in Subpart C of Title 14 CFR Part 77, Standards for Determining Obstructions to Air Navigation or Navigational Aids or Facilities.

ppp. Parallel Taxiway. A taxiway parallel to a runway:

(1) Dual Parallel Taxiways – Two side-by-side taxiways, parallel to each other and the runway.

(2) Full Parallel Taxiway – A parallel taxiway extending the full length of the runway.

(3) Partial Parallel Taxiway – A parallel taxiway extending less than full length of the runway.

qqq. Precision Approach (PA). For the purposes of this AC, an instrument approach procedure that provides course and vertical path guidance with visibility below 3/4 mile (4000 RVR).

rrr. Precision Runway. A runway with at least one end having a precision approach procedure.

sss. Runway (RW). A defined rectangular surface on an airport prepared or suitable for the landing or takeoff of aircraft.

ttt. Runway Design Code (RDC). A code signifying the design standards to which the runway is to be built.

uuu. Runway Incursion. Any occurrence at an airport involving the incorrect presence of an aircraft, vehicle or person on the protected area of a surface designated for the landing and takeoff of aircraft.

vvv. Runway Protection Zone (RPZ). An area at ground level prior to the threshold or beyond the runway end to enhance the safety and protection of people and property on the ground.

www. Runway Safety Area (RSA). A defined surface surrounding the runway prepared or suitable for reducing the risk of damage to aircraft in the event of an undershoot, overshoot, or excursion from the runway.

xxx. Shoulder. An area adjacent to the defined edge of paved runways, taxiways, or aprons providing a transition between the pavement and the adjacent surface; support for aircraft and emergency vehicles deviating from the full-strength pavement; enhanced drainage; and blast protection.

yyy. Small Aircraft. An aircraft with a maximum certificated takeoff weight of 12,500 lbs (5670 kg) or less.

zzz. Stopway (SWY). An area beyond the takeoff runway, no less wide than the runway and centered upon the extended centerline of the runway, able to support the airplane during an aborted takeoff, without causing structural damage to the airplane, and designated by the airport authorities for use in decelerating the airplane during an aborted takeoff. A blast pad is not a stopway.

aaaa. Takeoff Distance Available (TODA). See Declared Distances.

bbbb. Takeoff Run Available (TORA). See Declared Distances.

cccc. Taxilane (TL). A taxiway designed for low speed and precise taxiing. Taxilanes are usually, but not always, located outside the movement area, providing access from taxiways (usually an apron taxiway) to aircraft parking positions and other terminal areas.

dddd. Taxiway (TW). A defined path established for the taxiing of aircraft from one part of an airport to another.

eeee. Taxiway Design Group (TDG). A classification of airplanes based on outer to outer Main Gear Width (MGW) and Cockpit to Main Gear distance (CMG).

ffff. Taxiway Edge Safety Margin (TESM). The distance between the outer edge of the landing gear of an airplane with its nose gear on the taxiway centerline and the edge of the taxiway pavement.

gggg. Taxiway/Taxilane Safety Area (TSA). A defined surface alongside the taxiway prepared or suitable for reducing the risk of damage to an aircraft deviating from the taxiway.

hhhh. Threshold (TH). The beginning of that portion of the runway available for landing. In some instances, the threshold may be displaced. “Threshold” always refers to landing, not the start of takeoff.

iiii. Threshold Crossing Height (TCH). For the purposes of this AC, the TCH is the theoretical height above the runway threshold at which the aircraft’s glideslope (GS) antenna would be if the aircraft maintains the trajectory established by the Instrument Landing System (ILS) GS, or the height of the pilot’s eye above the runway threshold based on a visual guidance system.

Chapter 1. Introduction › 103. Roles of Federal, State and Local governments.

jjjj. Visual Runway. A runway without an existing or planned instrument approach procedure.

kkkk. Wingspan. The maximum horizontal distance from one wingtip to the other wingtip, including the horizontal component of any extensions such as winglets or raked wingtips.

103. Roles of Federal, State and Local governments.

a. Federal.

(1) Federal Assistance. The FAA administers a grant program (Order 5100.38) which provides financial assistance for developing public-use airports. Persons interested in the program can obtain information from the FAA Airports Regional Office or Airports District Office (ADO) that serves their geographic area. Consult these offices for assistance with selection of the design aircraft for federally funded projects, which depends on demand factors that are beyond the scope of this AC. Technical assistance with airport development is also available from these offices.

(2) Obligated Airports. Airport sponsors agree to certain obligations when they accept Federal grant funds or Federal property transfers for airport purposes. The duration of these obligations depends on the type, the recipient, the useful life of the facility being developed, and other conditions stipulated. The FAA enforces these obligations through its Airport Compliance Program. More information on the Airport Compliance Program can be found in Order 5190.6, FAA Airport Compliance Manual. Information on specific assurances and obligations associated with Federal grant funds can be found in Order 5100.38. The standards in this AC demonstrate compliance with obligations associated with airport design and development.

(3) Certificated Airports. The FAA regulates commercial service airports under Part 139. This regulation prescribes rules governing the certification and operation of airports in any State of the United States, the District of Columbia, or any territory or possession of the United States that serve scheduled or unscheduled passenger service. ACs contain methods and procedures that certificate holders may use to comply with the requirements of Part 139.

(4) Non-Obligated Public-Use and Private-Use Airports. For airports not included in subparagraphs (2) and (3) above:

(a) The standards in this AC are recommended for all civil airports.

(b) Proponents must comply with Part 157, Notice of Construction, Alteration, Activation, and Deactivation of Airports. See paragraph 104.

Chapter 1. Introduction › 104. Airport operator responsibilities.

(5) Environmental Protection. Federal assistance in airport development projects and ALP approvals require the FAA to follow the procedures of the NEPA in connection with project approval. NEPA requires the FAA to disclose to the interested public a clear, accurate description of potential environmental impacts and reasonable alternatives to the proposed action. Order 5050.4 provides guidance for meeting NEPA requirements. See also Order 1050.1, Policies and Procedures for Considering Environmental Impacts.

b. State. Design Standards. Although FAA can accept state standards for construction materials and methods under certain conditions (reference AC 150/5100-13, Development of State Standards for Nonprimary Airports), the use of state dimensional standards that differ from the standards in this AC are NOT acceptable for federally obligated or certificated airports.

c. Local. Many communities have zoning ordinances, building codes, and fire regulations that may affect airport development.

104. Airport operator responsibilities.

a. Notice of proposed construction.

(1) Part 77. Part 77 requires proponents of construction or alteration on or near airports to notify the FAA, allowing the FAA to evaluate the potential impact on air navigation. The FAA encourages filing the Notice electronically on the FAA’s Obstruction Evaluation/Airport Airspace Analysis (OE/AAA) website: https://oeaaa.faa.gov/oeaaa.

(2) Part 157. Part 157 applies to persons proposing to construct, alter, activate, or deactivate a civil or joint-use airport or to alter the status or use of such an airport. Certain exceptions apply. Refer to Part 157 for additional information.

(3) Plans on file. Future airport development plans and feasibility studies on file with the FAA may influence the determination resulting from Part 77 studies. Having their plans on file with the FAA is the only way airport owners can ensure full consideration of airport development. For any new runway, runway extension, or planned runway upgrade, the necessary plan data include, as a minimum, planned runway end and threshold coordinates, elevation(s), type of instrument approach,, visibility minimum(s) desired, and whether the runway will be a designated instrument departure runway. See paragraphs 107, 302 and 303. “Plan on file” data, in general, needs to be submitted by the airport owner with complete and sufficient information on the development. An update to the ALP is generally the best method to transmit plan on file information. Submit this information to the local FAA Airports Region or ADO that serves your geographic area. The location of Airports Region and ADO offices is available on the FAA website: www.faa.gov/airports, or the OE/AAA website: https://oeaaa.faa.gov/oeaaa.

(4) Additional information. Specific airspace procedures and requirements can be found in Order JO 7400.2, Procedures for Handling Airspace Matters, and AC 150/5200- 35, Submitting the Airport Master Record in Order to Activate a New Airport, for additional guidance.

b. Maintenance of obstacle clearance surfaces. Federally obligated airports are subject to Grant Assurances 20 and 21 which require the protection of the approach and departure surfaces. Airports operating under Code of Federal Regulations (CFR) Part 139 are also subject to Part 139.331 to mitigate obstructions. The airport operator has an ongoing obligation to review the surface(s) for obstructions. The FAA reviews all Instrument Approach Procedures (IAP) on a periodic basis; approximately every two years. Obstacles found within the associated approach/departure surfaces at that time may result in higher minima, loss of approaches and/or loss of night operations.

Chapter 1. Introduction › 105. Planning.

105. Planning.

Airport planning should consider both the present and potential aviation needs and demand associated with the airport. Consider planning for runways and taxiways locations that will meet future separation requirements even if the width, strength, and length must increase later. Such decisions should be supported by appropriate planning and should be shown on the approved ALP. Coordination with the FAA and users of the airport will assist in determining the immediate and long range characteristics that will best satisfy the needs of the community and travelling public. In general, however, airport planning is beyond the scope of this AC. See AC 150/5020-1, Noise Control and Compatibility Planning for Airports, AC 150/5060-5, Airport Capacity and Delay, AC 150/5070-6, Airport Master Plans, and AC 150/5070-7, The Airport System Planning Process.

a. Applicability of airport design standards. Airport design standards provide basic guidelines for a safe, efficient, and economic airport system. The standards and recommendations in this AC cover the wide range of size and performance characteristics of aircraft that are anticipated to use an airport. These standards and recommendations also cover various elements of airport infrastructure and their functions. Airport designers and planners need to carefully choose the basic aircraft characteristics for which the airport will be designed. Airport designs based only on existing aircraft can severely limit the ability to expand the airport to meet future requirements for larger, more demanding aircraft. Airport designs that are based on large aircraft never likely to be served by the airport are not economical. Building to the standards in this AC ensures that aircraft in a particular category can operate at the airport without restrictions or location-specific encumbrances that could impact safe and efficient operations.

b. Design aircraft. Planning a new airport or improvements to an existing airport requires the selection of one or more “design aircraft.” In the case of a private airport, the design aircraft can take the form of one particular aircraft, and frequency of operations may not be a consideration. In most cases, however, the design aircraft for the purposes of airport geometric design is a composite aircraft representing a collection of aircraft classified by three parameters: Aircraft Approach Category (AAC), Airplane Design Group (ADG) and Taxiway Design Group (TDG). These parameters, explained in detail in paragraph 105.c, represent the aircraft that are intended to be accommodated by the airport. In the case of an airport with multiple runways, a design aircraft is selected for each runway. The first consideration of the airport planner should be the safe operation of aircraft likely to use the airport. Any operation of an aircraft that exceeds design criteria of the airport may result in either an unsafe operation or a lesser safety margin unless air traffic control (ATC) Standard Operating Procedures (SOPs) are in place for

those operations. However, it is not the usual practice to base the airport design on an aircraft that uses the airport infrequently, and it is appropriate and necessary to develop ATC SOPs to accommodate faster and/or larger aircraft that use the airport occasionally. See paragraph 103.a regarding the selection of a design aircraft for airport development projects using federal assistance programs. Any aspect of airport design indicated in this AC as being based on a family of airplanes that does not accommodate the entire AAC, ADG, or TDG is subject to FAA review.

c. Runway Design Code (RDC). The selected AAC, ADG, and approach visibility minimums are combined to form the RDC of a particular runway. The RDC provides the information needed to determine certain design standards that apply. The first component, depicted by a letter, is the AAC and relates to aircraft approach speed (operational characteristics) (see Table 1-1). The second component, depicted by a Roman numeral, is the ADG and relates to either the aircraft wingspan or tail height (physical characteristics); whichever is most restrictive, of the largest aircraft expected to operate on the runway and taxiways adjacent to the runway (see Table 1-2). The third component relates to the visibility minimums expressed by RVR values in feet of 1200, 1600, 2400, 4000, and 5000 (corresponding to lower than 1/4 mile, lower than 1/2 mile but not lower than 1/4 mile, lower than 3/4 mile but not lower than 1/2 mile, lower than 1 mile but not lower than 3/4 mile, and not lower than 1 mile, respectively) (see Table 1-3).

The third component should read “VIS” for runways designed with visual approach use only. Generally, runway standards are related to aircraft approach speed, aircraft wingspan, and designated or planned approach visibility minimums. Runway to taxiway and taxiway/taxilane to taxiway/taxilane separation standards are related to ADG, TDG, and approach visibility minimums. For example, an airport’s air carrier runway can have an RDC of C-IV-1200. The same airport’s smaller runway used for general aviation activity can have an RDC of B-II-2400. (The design aircraft for other aspects of runway design, such as length and pavement strength, may be different. It will be based on other factors, such as haul length and maximum takeoff weight. See Chapter 3 for guidance on runway design and separation requirements. See Chapter 4 for guidance on taxiway design.

Table 1-1. Aircraft Approach Category (AAC)

AAC VREF/Approach Speed A Approach speed less than 91 knots B Approach speed 91 knots or more but less than 121 knots C Approach speed 121 knots or more but less than 141 knots D Approach speed 141 knots or more but less than 166 knots E Approach speed 166 knots or more

Table 1-2. Airplane Design Group (ADG)

Group # Tail Height (ft [m]) Wingspan (ft [m]) I < 20ʹ (< 6 m) < 49ʹ (< 15 m) II 20ʹ - < 30ʹ (6 m - < 9 m) 49ʹ - < 79ʹ (15 m - < 24 m) III 30ʹ - < 45ʹ (9 m - < 13.5 m) 79ʹ - < 118ʹ (24 m - < 36 m) IV 45ʹ - < 60ʹ (13.5 m - < 18.5 m) 118ʹ - < 171ʹ (36 m - < 52 m) V 60ʹ - < 66ʹ (18.5 m - < 20 m) 171ʹ - < 214ʹ (52 m - < 65 m) VI 66ʹ - < 80ʹ (20 m - < 24.5 m) 214ʹ - < 262ʹ (65 m - < 80 m)

Table 1-3. Visibility minimums

RVR (ft) * Instrument Flight Visibility Category (statute mile) 5000 Not lower than 1 mile 4000 Lower than 1 mile but not lower than ¾ mile 2400 Lower than 3/4 mile but not lower than 1/2 mile 1600 Lower than 1/2 mile but not lower than 1/4 mile 1200 Lower than 1/4 mile * RVR values are not exact equivalents.

d. Taxiway Design Group (TDG). TDG relates to the undercarriage dimensions of the aircraft. Taxiway/taxilane width and fillet standards, and in some instances, runway to taxiway and taxiway/taxilane separation requirements, are determined by TDG. It is appropriate for a series of taxiways on an airport to be built to a different TDG than another based on expected use. See Figure 1-1.

e. Approaches. Based on current and anticipated demand, the airport should be planned for appropriate minimums and aircraft. Such planning includes the appropriate RPZ size and approach slopes for the future design aircraft and visibility minimums. Proper planning should ensure that future airspace requirements are adequately protected with an FAA plan on file (see paragraph 104.a(3)). See paragraphs 306 and 302.d for obstruction clearing standards.

f. Land acquisition and airspace protection. Off-airport development will have a negative impact on current and future airport operations when it creates obstacles to the safe and efficient use of the airspace surrounding the airport. Consider off-airport conditions and land acquisition needs when designing the ultimate airport configuration, including the number and orientation of runways and proper separation for parallel taxiways and the terminal building complex. Land acquisition to protect all possible airspace intrusions is generally not feasible, and is usually supplemented by local zoning, easements, or other means to mitigate potential incompatible land uses and potential obstacle conflicts. AC 150/5190-4, A Model Zoning Ordinance to Limit Height of Objects around Airports, presents guidance for controlling the height of objects around airports. At a minimum for new runways, land acquisition should include Object Free Areas (OFAs) and Runway Protection Zones (RPZs). To the extent practicable, land acquisition should include adequate areas surrounding the runway(s) to protect the runway approach and departure surfaces identified in paragraph 303, and for existing and planned runways OFAs and RPZs.

Chapter 1. Introduction › 107. Collection, processing and publication of airport data.

Figure 1-1. Taxiway Design Groups (TDGs)

106. Airport Layout Plan (ALP).

a. Description. An ALP is a scaled drawing (or set of drawings), in either traditional or electronic form, of existing and proposed land and facilities necessary for the operation and development of the airport. Any airport will benefit from a carefully developed plan that reflects current FAA design standards and planning criteria. AC 150/5070-6 contains guidance on the development of ALPs, as well as a detailed listing of the various components that constitute a well-appointed ALP.

b. Federally obligated airports. All airport development at federally obligated airports must conform to an FAA-approved ALP. The ALP should conform to the FAA airport design standards existing at the time of its approval. Due to unusual site, environmental, or other constraints, the FAA may approve an ALP not fully complying with design standards. Such approval requires the FAA to determine the proposed modification to standards is safe for the specific site and conditions. See Order 5300.1. When the FAA revises a standard, airport owners should incorporate the changes in the ALP and implement the new standards before all new development.

107. Collection, processing and publication of airport data.

a. Airport data needs. Airport planning, design, and evaluation activities require information that accurately describes the location and condition of airport facilities as well as

40

60

80

100

120

20

140

0

COCKPIT TO MAIN GEAR (FEET)

TDG-7

TDG-1B

0 10 20 30 40 50 60

MAIN GEAR WIDTH (FEET)

TDG-1A

TDG-2

TDG-3

TDG-4

TDG-6

TDG-5

off-airport structures and features. This information is derived from geospatial data that are collected during the planning, design, and construction phase of airport development. Geospatial data describe objects in a three-dimensional geographic reference system that relates physical objects with the surrounding airspace. It is crucial for airports to accurately collect and report safety-critical data to the FAA in a timely manner. AC 150/5300-18, General Guidance and Specifications for Submission of Aeronautical Surveys to NGS: Field Data Collection and Geographic Information System (GIS) Standards, provides standards for identifying, collecting, and reporting safety critical data. FAA uses these data, in part, to:

(1) Protect existing runway approaches from proposed development that could create a hazard to air navigation,

(2) Provide for the design and development of new IAPs to the lowest visibility minimums possible,

(3) Provide accurate information for planning studies that assess the impact of airport noise, and

(4) Ensure that review and coordination of on-airport development proposals maintain critical clearance standards for the completed project.

b. Airspace data. The FAA conducts airspace studies of proposed development under Part 77 as described in paragraph 104. These studies assess the potential impact on air navigation using the best available data and plans on file. To ensure that the FAA has the best possible data with which to conduct these studies, the airport should submit any airfield changes as soon as they occur. This process is usually done in connection with ALP updates, but airports are encouraged to keep the FAA up to date with critical changes any time they occur. In particular, ensure that FAA has the latest data on actual and planned facilities for:

(1) Runway ends.

(2) Displaced thresholds.

(3) High and low points on the runway surfaces.

(4) Helipads.

c. Airport master record. The FAA maintains airport master records that are used to publish safety and operational information in the Airport/Facility Directory (A/FD). This information is usually collected during periodic FAA-sponsored inspections of the airport. These inspections collect information on runway length, runway condition, runway strength, navigational facilities, and controlling obstructions as well as other important data. Inspections are conducted in connection with Part 139 certification inspections for commercial service airports and Airport Master Record inspection for all other airports. Airport operators should become aware of the inspection schedules for their airports and ensure that the inspectors are provided with the latest changes to insure that FAA publications are current and accurate.

Chapter 1. Introduction › 108. Related Advisory Circulars (ACs), Orders, and Federal regulations.

d. Aeronautical surveys. The FAA uses aeronautical surveys to develop and modify instrument procedures. Survey requirements are provided by AC 150/5300-16, General Guidance and Specifications for Aeronautical Surveys: Establishment of Geodetic Control and Submission to the National Geodetic Survey, AC 150/5300-17, Standards for Using Remote Sensing Technologies in Airport Surveys, and AC 150/5300-18.

e. Airports Geographic Information System (GIS). The Airports GIS is a comprehensive geographic information system that will house critical safety data for the FAA and the airport community. Data in the Airports GIS will be collected by individual airports and validated by the FAA for use, in part, to:

(1) Conduct airspace studies

(2) Publish aeronautical information

(3) Develop instrument flight procedures

(4) Facilitate internal review and coordination of all airport development proposals.

Airports GIS information and data specifications can be found in AC 150/5300-18.

108. Related Advisory Circulars (ACs), Orders, and Federal regulations.

The following is a list of documents referenced in this AC and additional related information. Most Advisory Circulars, Orders, and Regulations can be found online at www.faa.gov. All references to ACs, Orders, and Federal Regulations are to be the most recent versions.

a. Advisory Circulars (ACs).

(1) AC 00-44, Status of Federal Aviation Regulations, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.c urrent/documentNumber/00-44.

(2) AC 20-35, Tiedown Sense, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/ documentNumber/20-35.

(3) AC 70/7460-1, Obstruction Marking and Lighting, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/70_7460-1.

(4) AC 103-6, Ultralight Vehicle Operations – Airports, ATC, and Weather, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/103-6.

(5) AC 120-28, Criteria for Approval of Category III Weather Minima for Takeoff, Landing and Rollout, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/120-28.

(6) AC 120-29, Criteria for Approval of Category I and Category II Weather Minimums for Approach, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/120-29.

(7) AC 120-57, Surface Movement Guidance and Control System, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/120-57.

(8) AC 150/5020-1, Noise Control and Compatibility Planning for Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5020-1.

(9) AC 150/5060-5, Airport Capacity and Delay, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/ documentNumber/150_5060-5.

(10) AC 150/5070-6, Airport Master Plans, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/ documentNumber/150_5070-6.

(11) AC 150/5070-7, The Airport System Planning Process, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5070-7.

(12) AC 150/5100-13, Development of State Standards for Nonprimary Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5100-13.

(13) AC 150/5100-17, Land Acquisition and Relocation Assistance for Airport Improvement Program Assisted Projects, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5100-17.

(14) AC 150/5190-4, A Model Zoning Ordinance to Limit Height of Objects around Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5190-4.

(15) AC 150/5190-6, Exclusive Rights at Federally Obligated Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5190-6.

(16) AC 150/5190-7, Minimum Standards for Commercial Aeronautical Activities, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5190-7.

(17) AC 150/5200-33, Hazardous Wildlife Attractants On or Near Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5200-33.

(18) AC 150/5200-34, Construction or Establishment of Landfills near Public Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5200-34.

(19) AC 150/5200-35, Submitting the Airport Master Record in Order to Activate a New Airport, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5200-35.

(20) AC 150/5210-15, Aircraft Rescue and Firefighting Station Building Design, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5210-15.

(21) AC 150/5210-22, Airport Certification Manual (ACM), http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5210-22.

(22) AC 150/5220-16, Automated Weather Observing Systems (AWOS) for Non-Federal Applications, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.c urrent/documentNumber/150_5220-16.

(23) AC 150/5220-18, Buildings for Storage and Maintenance of Airport Snow and Ice Control Equipment and Materials, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5220-18.

(24) AC 150/5220-22, Engineered Materials Arresting Systems (EMAS) for Aircraft Overruns, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5220-22.

(25) AC 150/5220-23, Frangible Connections, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.c urrent/documentNumber/150_5220-23.

(26) AC 150/5220-26, Airport Ground Vehicle Automatic Dependent Surveillance - Broadcast (ADS-B) Out Squitter Equipment, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.cu rrent/documentNumber/150_5220-26.

(27) AC 150/5230-4, Aircraft Fuel Storage, Handling, and Dispensing on Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5230-4.

(28) AC 150/5300-7, FAA Policy on Facility Relocations Occasioned by Airport Improvements or Changes, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5300-7.

(29) AC 150/5300-14, Design of Aircraft Deicing Facilities, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5300-14.

(30) AC 150/5300-16, General Guidance and Specifications for Aeronautical Surveys: Establishment of Geodetic Control and Submission to the National Geodetic Survey, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5300-16.

(31) AC 150/5300-17, Standards for Using Remote Sensing Technologies in Airport Surveys, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5300-17.

(32) AC 150/5300-18, General Guidance and Specifications for Submission of Aeronautical Surveys to NGS: Field Data Collection and Geographic Information System (GIS) Standards, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5300-18.

(33) AC 150/5320-5 (UFC 3-230-01), Surface Drainage Design, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5320-5.

(34) AC 150/5320-6, Airport Pavement Design and Evaluation, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.cur rent/documentNumber/150_5320-6.

(35) AC 150/5320-12, Measurement, Construction, and Maintenance of Skid Resistant Airport Pavement Surfaces, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5320-12.

(36) AC 150/5320-15, Management of Airport Industrial Waste, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/ documentNumber/150_5320-15.

(37) AC 150/5325-4, Runway Length Requirements for Airport Design, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5325-4.

(38) AC 150/5335-5, Standardized Method of Reporting Airport Pavement Strength – PCN, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/d ocumentNumber/150_5335-5.

(39) AC 150/5340 and 150/5345 series, http://www.faa.gov/regulations_policies/advisory_circulars/index.cfm/go/document.list/p arentTopicID/63.

(40) AC 150/5340-1, Standards for Airport Markings, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5340-1.

(41) AC 150/5340-5, Segmented Circle Airport Marker System, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5340-5.

(42) AC 150/5340-18, Standards for Airport Sign Systems, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5340-18.

(43) AC 150/5340-30, Design and Installation Details for Airport Visual Aids, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/d ocumentNumber/150_5340-30.

(44) AC 150/5345-43, Specification for Obstruction Lighting Equipment, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.cu rrent/documentNumber/150_5345-43.

(45) AC 150/5345-44, Specification for Runway and Taxiway Signs, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/ documentNumber/150_5345-44.

(46) AC 150/5345-52, Generic Visual Glideslope Indicators (GVGI), http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5345-52.

(47) AC 150/5360-9, Planning and Design of Airport Terminal Facilities at Non-Hub Locations, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5360-9.

(48) AC 150/5360-13, Planning and Design Guidelines for Airport Terminal Facilities, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curr ent/documentNumber/150_5360-13.

(49) AC 150/5370-2, Operational Safety on Airports during Construction, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.c urrent/documentNumber/150_5370-2.

(50) AC 150/5370-10, Standards for Specifying Construction of Airports, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curre nt/documentNumber/150_5370-10.

(51) AC 150/5370-15, Airside Applications for Artificial Turf, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/d ocumentNumber/150_5370-15.

(52) AC 150/5390-2, Heliport Design, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.curren t/documentNumber/150_5390-2.

(53) AC 150/5395-1, Seaplane Bases, http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.current/ documentNumber/150_5395-1.

b. Engineering Briefs. Engineering Briefs cover various subjects, and supplement Advisory Circulars. Engineering Briefs are available at: http://www.faa.gov/airports/engineering/engineering_briefs/.

c. Orders.

(1) Order 1050.1, Policies and Procedures for Considering Environmental Impacts, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current /documentNumber/1050.1.

(2) Order 5050.4, National Environmental Policy Act (NEPA) Implementing Instructions for Airport Projects, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current /documentNumber/5050.4.

(3) Order 5090.3, Field Formulation of the National Plan of Integrated Airport Systems (NPIAS), http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curren t/documentNumber/5090.3.

(4) Order 5100.37, Land Acquisition and Relocation Assistance for Airport Projects, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current /documentNumber/5100.37.

(5) Order 5100.38, Airport Improvement Program Handbook, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/5100.38.

(6) Order 5190.6, FAA Airport Compliance Manual, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/5190.6.

(7) Order 5200.8, Runway Safety Area Program, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curren t/documentNumber/5200.8.

(8) Order 5200.9, Financial Feasibility and Equivalency of Runway Safety Area Improvements and Engineered Material Arresting Systems, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current /documentNumber/5200.9.

(9) Order 5200.11, FAA Airports (ARP) Safety Management System (SMS), http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/5200.11.

(10) Order 5300.1, Modifications to Agency Airport Design, Construction, and Equipment Standards, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/5300.1.

(11) Order 6030.20, Electrical Power Policy, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/d ocumentNumber/6030.20.

(12) Order 6310.6, Primary/secondary Terminal Radar Siting Handbook, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/6310.6.

(13) Order 6480.4, Airport Traffic Control Tower Siting Criteria, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/6480.4.

(14) Order 6560.10, Runway Visual Range (RVR), http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/6560.10.

(15) Order 6560.20, Siting Criteria for Automated Weather Observing Systems (AWOS), http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curren t/documentNumber/6560.20.

(16) Order 6560.21, Siting Guidelines for Low Level Windshear Alert System (LLWAS) Remote Facilities, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curren t/documentNumber/6560.21.

(17) Order JO 6580.3, Remote Communications Facilities Installation Standards Handbook, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/6580.3.

(18) Order 6750.16, Siting Criteria for Instrument Landing Systems, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current /documentNumber/6750.16.

(19) Order 6750.36, Site Survey, Selection, and Engineering Documentation for ILS and Ancillary Aids, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/do cumentNumber/6750.36.

(20) Order 6780.5, DME Installation Standards Handbook Type FA-96- 39, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/docu mentNumber/6780.5.

(21) Order 6820.9, VOR, VOR/DME, VORTAC Installation Standard Drawings, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/6820.9.

(22) Order 6820.10, VOR, VOR/DME and VORTAC Siting Criteria, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/6820.10.

(23) Order JO 6850.2, Visual Guidance Lighting Systems, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.inform ation/documentID/321004.

(24) Order 6850.10, Runway End Identifier Lighting (REIL) System Standard Drawings, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/6850.10.

(25) Order 6850.19, Frangible Coupling, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/6850.19.

(26) Order 6850.20, Medium Intensity Approach Lighting System Threshold Lighting Backfit, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/6850.20

(27) Order 6950.23, Cable Loop Communication Systems at Airport Facilities, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curren t/documentNumber/6950.23.

(28) Order 7110.104, Non-Federal Automated Weather Observation System (AWOS) Connection to the Weather Messaging Switching, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.curre nt/documentNumber/7110.104.

(29) Order JO 7400.2, Procedures for Handling Airspace Matters, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/7400.2.

(30) Order 8200.1, United States Standard Flight Inspection Manual, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current/ documentNumber/8200.1.

(31) Order 8260.3, United States Standard for Terminal Instrument Procedures (TERPS), https://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.current /documentNumber/8260.3.

(32) Other Orders in the 8260 series, http://www.faa.gov/regulations_policies/orders_notices/index.cfm/go/document.list?omni =OrdersNotices&q=8260&documentTypeIDList=2&display=all&parentTopicID=0&document Number=.

d. Federal Regulations.

(1) 14 CFR Part 1, Definitions and Abbreviations, http://www.ecfr.gov/cgibin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:1.0.1.1. 1&idno=14.

(2) 14 CFR Part 23, Airworthiness Standards: Normal, Utility, Acrobatic, and Commuter Category Airplanes, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:1.0.1.3. 10&idno=14.

(3) 14 CFR Part 25, Airworthiness Standards: Transport Category Airplanes, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:1.0.1.3. 11&idno=14.

(4) 14 CFR Part 77, Safe, Efficient Use, and Preservation of the Navigable Airspace, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:2.0.1.2. 9&idno=14.

(5) 14 CFR Part 91, General Operating and Flight Rules, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:2.0.1.3. 10&idno=14.

(6) 14 CFR Part 97, Standard Instrument Procedures, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:2.0.1.3. 13&idno=14.

(7) 14 CFR Part 121, Operating Requirements: Domestic, Flag, and Supplemental Operations, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.1. 7&idno=14.

(8) 14 CFR Part 129, Operations: Foreign Air Carriers and Foreign Operators of U.S.-Registered Aircraft Engaged in Common Carriage, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.1. 9&idno=14.

(9) 14 CFR Part 135, Operating Requirements: Commuter and On Demand Operations and Rules Governing Persons On Board Such Aircraft, http://www.ecfr.gov/cgibin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.1. 11&idno=14.

(10) 14 CFR Part 139, Certification of Airports, http://www.ecfr.gov/cgibin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.1. 14&idno=14.

(11) 14 CFR Part 150, Airport Noise Compatibility Planning, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.3. 21&idno=14.

(12) 14 CFR Part 151, Federal Aid to Airports, http://www.ecfr.gov/cgibin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.3. 22&idno=1.

(13) 14 CFR Part 152, Airport Aid Program, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.3. 23&idno=14.

(14) 14 CFR Part 157, Notice of Construction, Alteration, Activation, and Deactivation of Airports, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.3. 27&idno=14.

(15) 14 CFR Part 171, Non-Federal Navigation Facilities, http://www.ecfr.gov/cgi-bin/text-

idx?c=ecfr&sid=fab9bfa191e740463dbdb9acc14b6e2a&rgn=div5&view=text&node=14:3.0.1.4. 32&idno=14.

(16) 49 CFR, Chapter XII, Parts 1500 through 1699, http://www.ecfr.gov/cgibin/textidx?sid=82e39459c7b60fa3ca608515797ea1c5&c=ecfr&tpl=/ecfrbrowse/Title49/49cfrv9_02.tpl #1200.

(17) 49 CFR Part 24, Uniform Relocation Assistance and Real Property Acquisition for Federal and Federally-Assisted Programs, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:1.0.1.1. 18&idno=49.

(18) 49 USC Chapter 401, General Provisions, http://www.gpo.gov/fdsys/granule/USCODE-2011-title49/USCODE-2011-title49subtitleVII-partA-subparti-chap401/content-detail.html.

(19) 49 USC Chapter 471, Airport Development, http://www.gpo.gov/fdsys/granule/USCODE-2011-title49/USCODE-2011-title49subtitleVII-partB-chap471/content-detail.html.

(20) 49 CFR Part 1540, Civil Aviation Security: General Rules, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr;sid=bea8e3d217db2cf2a562c85911cc3f7f;rgn=div5;view=text;node=49%3A9.1.3.5.9 ;idno=49;cc=ecfr.

(21) 49 CFR Part 1542, Airport Security, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 10&idno=49.

(22) 49 CFR Part 1544, Aircraft Operator Security: Air Carriers and Commercial Operators, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 11&idno=49.

(23) 49 CFR Part 1546, Foreign Air Carrier Security http://www.ecfr.gov/cgibin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 12&idno=49.

(24) 49 CFR Part 1548, Indirect Air Carrier Security, http://www.ecfr.gov/cgibin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 13&idno=49.

(25) 49 CFR Part 1549, Certified Cargo Screening Program, http://www.ecfr.gov/cgi-bin/text-

idx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 14&idno=49.

(26) 49 CFR Part 1550, Aircraft Security under General Operating and Flight Rules, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 15&idno=49.

(27) 49 CFR Part 1552, Flight Schools, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 16&idno=49.

(28) 49 CFR Part 1560, Secure Flight Program, http://www.ecfr.gov/cgibin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 17&idno=49.

(29) 49 CFR Part 1562, Operations in the Washington, DC, Metropolitan Area, http://www.ecfr.gov/cgi-bin/textidx?c=ecfr&sid=f8c021cea6b0746900717e84b2fe6ccd&rgn=div5&view=text&node=49:9.1.3.5. 18&idno=49.

e. FAA Forms.

(1) Form 5010, Airport Master Record, http://www.faa.gov/forms/index.cfm/go/document.list?omni=Forms&q=5010&parentTo picID=0&display=current&subjectClassPrefix=&documentNumber=.

(2) Form 7460-1, Notice of Proposed Construction or Alteration, http://www.faa.gov/forms/index.cfm/go/document.information/documentID/186273.

(3) Form 7480-1, Notice of Landing Area Proposal, http://www.faa.gov/forms/index.cfm/go/document.information/documentID/185334.

f. Other.

(1) Aeronautical Information Manual (AIM), http://www.faa.gov/air_traffic/publications/atpubs/aim/.

(2) Aeronautical Information Publication, http://www.faa.gov/air_traffic/publications/media/aip.pdf.

(3) Airport Cooperative Research Program (ACRP) Report 25, Airport Passenger Terminal Planning and Design, Volume I, http://onlinepubs.trb.org/onlinepubs/acrp/acrp_rpt_025v1.pdf.

(4) Airport/Facility Directory (A/FD), http://www.faa.gov/air_traffic/flight_info/aeronav/productcatalog/supplementalcharts/Ai rportDirectory/.

(5) American Association of State Highway and Transportation Officials (AASHTO) M268, Standard Specification for Retroreflective Sheeting for Flat and Vertical Traffic Control Applications.

(6) American Society for Testing and Materials International (ASTM) D4956, Standard Specification for Retroreflective Sheeting for Traffic Control, http://www.astm.org/Standards/D4956.htm.

(7) ASTM E810, Standard Test Method for Coefficient of Retroreflection of Retroreflective Sheeting Utilizing the Coplanar Geometry, http://www.astm.org/Standards/E810.htm.

(8) FAA Airport Diagrams, http://aeronav.faa.gov/index.asp?xml=aeronav/applications/d_tpp.

(9) FAA Memorandum, Interim Guidance on Land Uses Within a Runway Protection Zone, dated 9/27/2012.

(10) FAA/USDA manual, Wildlife Hazard Management at Airports, http://www.faa.gov/airports/airport_safety/wildlife/problem/media/2005_FAA_Manual _complete.pdf.

(11) FAA-C-1217, Electrical Work, Interior, https://faaco.faa.gov/attachments/attachment_3.pdf.

(12) FAA-C-1391, Installation and Splicing of Underground Cables, https://faaco.faa.gov/attachments/FAA-C-1391b1.pdf.

(13) FAA-STD-019, Lightning and Surge Protection, Grounding, Bonding and Shielding Requirements for Facilities and Electronics Equipment, https://faaco.faa.gov/attachments/STD-019e2.pdf.

(14) Federal Specification FP-85, Standard Specifications for Construction of Roads and Bridges on Federal Highway Projects.

(15) Grant Assurances No. 20, Hazard Removal and Mitigation, No. 21, Compatible Land Use, No. 34, Policies, Standards, and Specifications, and PFC Assurance No. 9, Standards and Specifications, http://www.faa.gov/airports/aip/grant_assurances/media/airport_sponsor_assuran ces_2012.pdf.

(16) Illuminating Engineering Society of North America (IES), Recommended Practice for Airport Service Area Lighting.

Chapter 1. Introduction › 109. to 199. Reserved.

(17) International Air Transport Association (IATA), Airport Development Reference Manual (ADRM).

(18) NASA/Aviation Safety Reporting System (ASRS) Directline Issue No. 6, August 1993, Ground Jet Blast Hazard, http://asrs.arc.nasa.gov/publications/directline/dl6_blast.htm.

(19) National Fire Protection Association (NFPA) 407, Standard for Aircraft Fuel Servicing, http://www.nfpa.org/aboutthecodes/AboutTheCodes.asp?DocNum=407.

(20) NFPA 409, Standard on Aircraft Hangars, http://www.nfpa.org/aboutthecodes/AboutTheCodes.asp?DocNum=409.

(21) NFPA 415, Standard on Airport Terminal Building, Fueling Ramp Drainage and Loading Walkways, http://www.nfpa.org/aboutthecodes/AboutTheCodes.asp?DocNum=415.

(22) Transportation Security Administration document, Recommended Security Guidelines for Airport Planning and Construction, https://www.sskies.org/images/uploads/subpage/ PARAS_0004.Recommended_Security_Guidelines.FinalReport.v2.pdf.

(23) Transportation Security Administration Information Publication A-001, Security Guidelines for General Aviation Airports, https://www.tsa.gov/sites/default/files/2017_ga_security_guidelines.pdf.

109. to 199. Reserved.

Chapter 2. Design Process

201. General.

Airport design first requires selecting the Runway Design Code(s) (RDC[s]) (see paragraph 105.c), for desired/planned level of service for each runway, and then applying the airport design criteria associated with the RDC. Table 2-1 depicts the changes in design standards associated with changes in the approach category and airplane design group. Table 2-2 depicts the change in design standards associated with changes in visibility minimums.

Chapter 2. Design Process › 201. General.

a. Instrument flight procedures minimums are based on the characteristics and infrastructure of the runway (i.e., markings, approach light system, protected airspace, etc.), airspace evaluation, and the navigation system available to the aircraft. Unless these items are considered in the development of the airport, the operational minimums may be other than desired.

b. For airports with two or more runways, it is often desirable to design all airport elements to meet the requirements of the most demanding RDC and Taxiway Design Group (TDG). However, it may be more practical and economical to design some airport elements, e.g., a secondary runway and its associated taxiway, to standards associated with a lesser demanding RDC and TDG. A typical example would be an air carrier airport that has a separate general aviation or commuter runway or a crosswind runway only needed for small aircraft.

Table 2-1. Changes in airport design standards associated with an upgrade in the first two

components (Aircraft Approach Category [AAC] and Airplane Design Group [ADG]) of

the Runway Design Code (RDC)

AAC/RDC

upgrade Changes in airport design standards.

A-I* to B-I* No change in airport design standards.

B-I* to C-I

Increase in crosswind component. Refer to paragraph 302.c(3) and Table 3-1. Increase in runway separation standards. Refer to interactive Table 3-5 and Table 3-6. Increase in RPZ dimensions. Refer to Table 3-5 and paragraph 310.c. Increase in OFZ dimensions. Refer to paragraph 308. Increase in runway design standards. Refer to Table 3-5. Increase in surface gradient standards. Refer to paragraph 313, Figure 4-33,

paragraph 418, and paragraph 508. Increase in threshold siting standards. Refer to paragraph 303.

A-I to B-I No change in airport design standards.

B-I to C-1

Increase in crosswind component. Refer to paragraph 302.c(3) and Table 3-1. Increase in runway separation standards. Refer to Table 3-5 and Table 3-6. Increase in RPZ dimensions. Refer to Table 3-5 and paragraph 310.c. Increase in runway design standards. Refer to Table 3-5. Increase in surface gradient standards. Refer to paragraphs 313, Figure 4-33,

paragraph 418, and paragraph 508.

A-II to B-II No change in airport design standards.

B-II to C-II

Increase in crosswind component. Refer to paragraph 302.c(3) and Table 3-1. Increase in runway separation standards. Refer to Table 3-5 and Table 3-6. Increase in RPZ dimensions. Refer to Table 3-5 and paragraph 310.c. Increase in runway design standards. Refer to Table 3-5. Increase in surface gradient standards. Refer to paragraph 313, Figure 4-33,

paragraph 418 and paragraph 508.

A-III to B-III No change in airport standards.

B-III to C-III

Increase in runway separation standards. Refer to Table 3-5 and Table 3-6. Increase in RPZ dimensions. Refer to Table 3-5 and paragraph 310.c. Increase in runway design standards. Refer to Table 3-5. Increase in surface gradient standards. Refer to paragraph 313, Figure 4-33,

paragraph 418 and paragraph 508.

A-IV to

B-IV No change in airport design standards.

B-IV to C-IV

Increase in RPZ dimensions. Refer to Table 3-5 and paragraph 310.c. Increase in surface gradient standards. Refer to paragraph 313, Figure 4-33,

paragraph 418 and paragraph 508.

C-I to D-I Increase in runway design standards. Refer to Table 3-5. C-II to D-II Increase in runway design standards. Refer to Table 3-5. * These airport design standards pertain to facilities designed for small aircraft.

Table 2-2. Changes in airport design standards associated with lowering the third

Chapter 2. Design Process › 202. Design aircraft.

component (approach visibility minimums) of the Runway Design Code (RDC)

Visibility minimums* Changes in airport design standards

Visual

to Not lower than

1-mile

No change in airport design standards.

Not lower than

1-mile to Not lower than

3/4-mile

Parallel Taxiway

Increase in RPZ dimensions. Refer to interactive Table 3-5. Increase in threshold siting standards. Refer to paragraph 303.

Not lower than

3/4-mile to Not lower than

CAT-I

For aircraft approach categories A & B runways:

Increase in runway separation standards. Refer to Table 3-5 and

Table 3-6. Increase in RPZ dimensions. Refer to Table 3-5. Increase in OFZ dimensions. Refer to paragraph 308. Increase in runway design standards. Refer to Table 3-5. Increase in threshold siting standards. Refer to paragraph 303. For aircraft approach categories C, D, & E runways:

Increase in runway separation standards for ADG-I & ADG-II runways. Refer to Table 3-5 and Table 3-6. Increase in RPZ dimensions. Refer to Table 3-5. Increase in OFZ dimensions. Refer to paragraph 308. Increase in threshold siting standards. Refer to paragraph 303. Not lower than

CAT-I

to Lower than

CAT-I

Increase in OFZ dimensions for runways serving large aircraft. Refer to

paragraph 308. Increase in threshold siting standards. Refer to paragraph 303.

* In addition to the changes in airport design standards as noted, providing for lower approach visibility minimums may result in an increase in the number of objects identified as obstructions to air navigation in accordance with Part 77. This may require object removal or marking and lighting. Refer to paragraph 306.

202. Design aircraft.

The design aircraft enables airport planners and engineers to design the airport in such a way as to satisfy the operational requirements of such aircraft and meet national standards for separation and geometric design (safety issues). The “design” aircraft may be a single aircraft or a composite of several different aircraft composed of the most demanding characteristics of each (see paragraph 105.b.). Examples of such characteristics and the design components affected are detailed in Table 2-3. The selection of the design aircraft is beyond the scope of this AC.

Chapter 2. Design Process › 204. Airport design standards and the environmental process.

Table 2-3. Aircraft characteristics and design components

Aircraft Characteristics Design Components Approach Speed RSA, ROFA, RPZ, runway width, runway-to-taxiway separation, runway-to-fixed object. Landing and Takeoff Distance Runway length Cockpit to Main Gear Distance (CMG)

Fillet design, apron area, parking layout

Main Gear Width (MGW) Taxiway width, fillet design Wingspan / Tail Height Taxiway and apron OFA, parking configuration, hangar locations, taxiway-to-taxiway separation, runway to taxiway separation

203. Runway incursions.

The overall airfield design should be developed with the intent of preventing runway incursions. Taxiway design and runway incursion prevention are discussed in Chapter 4.

204. Airport design standards and the environmental process.

a. Purpose and Need. For projects using funds from federal financial assistance programs, design standards in this advisory circular (AC) represent the key components of the airport that are needed to fulfill the federal mission and policy as stipulated by USC Title 49, Chapter 471, Airport Development. Chapter 471 requires balancing a variety of interests associated with the airports, including:

• Safe operations

• Increasing capacity and efficiency

• Delay reduction

• Economic viability

• Noise reduction

• Environmental protection

These standards work to balance these interests. For normal environmental processes, these standards establish the fundamental purpose and need for airport development.

b. Safety. All prudent and feasible alternatives must be considered when a proposed development project has potential environmental effects. However, safety is the highest priority for any airport development and any airport operations.

Chapter 2. Design Process › 205. Planned visibility minimums for instrument procedures.

205. Planned visibility minimums for instrument procedures.

Runways provide maximum utility when they can be used in less than ideal weather conditions. For runways, weather conditions translate to visibility in terms of the distance to see and identify prominent unlighted objects by day and prominent lighted objects by night. In order to land during periods of limited visibility, pilots must be able to see the runway or associated lighting at a certain distance from and height above the runway. If the runway environment cannot be identified at the minimum visibility point on the approach, FAA regulations do not authorize pilots to land.

a. Planning considerations. While lower visibility minimums are often desirable, runway design requirements ranging from obstacles in the approach path to separation and buffers around the runway become much more restrictive. Therefore, it is important to carefully weigh the demand, benefits and costs when deciding the visibility minimums for which the runway will be designed.

b. Visibility categories. The ultimate runway development should be designed for one of the following visibility categories:

(1) Visual (V). Runways classified as visual are not designed to handle or anticipated to handle any Instrument Flight Rules (IFR) operations now or in the future, except circling approaches. These runways support Visual Flight Rules (VFR) operations only and are unlighted or lighted with at least Low Intensity Runway Lights (LIRL) or medium intensity runway lights (MIRL), and have only visual (basic) runway markings as defined in AC 150/5340-1.

(2) Non-Precision Approach (NPA). Runways classified as NPA are designed to handle straight-in instrument approaches providing only lateral guidance. NPA runways will only support IFR approach operations to visibilities of 3/4 statute mile (1.2 km) or greater. Navigation Aids (NAVAIDs) providing lateral only guidance for instrument approaches are VHF Omnidirectional Range (VOR), non-directional beacon (NDB), Area Navigation (RNAV) Lateral Navigation (LNAV), localizer performance (LP), localizer (LOC). These runways are generally at least 3,200 feet (975 m) long, with a minimum width based on RDC, are lighted using at least LIRL or MIRL, and have non-precision runway markings as defined in AC 150/5340-1. Runways less than 3,200 feet are protected by Part 77 to a lesser extent. However, runways as short as 2,400 feet could support an instrument approach provided the lowest Height Above Threshold (HATh) is based on clearing any 200-foot (61 m) obstacle within the final approach segment.

(3) Approach Procedure with Vertical Guidance (APV). Runways classified as APV are designed to handle instrument approach operations where the navigation system provides vertical guidance down to 250 feet HATh and visibilities to as low as 3/4 statute mile. May apply to the following approach types: Instrument Landing System (ILS), LNAV/ Vertical Navigation (VNAV), Localizer Performance with Vertical Guidance (LPV), or Area Navigation (RNAV)/Required Navigation Performance (RNP). These runways must be at least 3,200 feet (975 m) in length with a width at least 60 feet (18.5 m) (with 75 or 100 feet [23 or 30 m]

Chapter 2. Design Process › 206. Airport Traffic Control Tower (ATCT) siting.

typically being optimum), and must have at least MIRL with non-precision runway markings as defined in AC 150/5340-1.

(4) Precision Approach (PA). Runways classified as precision are designed to handle instrument approach operations supporting instrument approach with HATh lower than 250 feet and visibility lower than 3/4 statute mile, down to and including Category (CAT) III. Precision Instrument Runways (PIR) support IFR operations with visibilities down to and including CAT-III with the appropriate infrastructure. The navigational systems capable of supporting precision operations are ILS, LPV, and Global Navigation Satellite System (GNSS) Landing System (GLS). These runways must be at least 4200 feet (1280 m) long, and are at least 75 feet (23 m) wide with the typical width being at least 100 feet (30 m). These runways are typically lighted by High Intensity Runway Lights (HIRL) and must have precision runway markings as defined in AC 150/5340-1.

206. Airport Traffic Control Tower (ATCT) siting.

a. General. The ATCT should be constructed at the minimum height required to satisfy all siting criteria. Order 6480.4 provides guidance on siting criteria and the evaluation and approval procedures for the height and location of an ATCT to ensure safety within the National Airspace System (NAS). The existing (or future) ATCT must have a clear line of sight (LOS) to: all traffic patterns, the final approaches to all runways, all runway structural pavement, and other operational surfaces controlled by Air Traffic Control (ATC). A clear LOS to taxilane centerlines is desirable. Operational surfaces not having a clear unobstructed LOS from the ATCT are designated by ATC as non-movement areas through a local agreement with the airport owner.

b. Land requirements. From ATCTs, ATC personnel control flight operations within the airport’s designated airspace and the operation of aircraft and vehicles on the movement area. A typical ATCT site will range from 3 to 7 acres. Additional land may be needed for combined ATC facilities. The proposed site must consider security requirements and be large enough to accommodate current and future building needs, including reasonable provisions for employee parking.

c. Considerations for planned runway and/or taxiway extensions. During the planning of a runway or taxiway extension, the existing ATCT site should be evaluated for impacts from the extension, such as object discrimination, unobstructed view, and two-point lateral discrimination (depth perception).

d. Considerations for planned taxiway construction projects. During the planning of a taxiway construction project, the existing ATCT site should be evaluated for impacts due to construction, such as an unobstructed view from construction equipment and/or activities, temporary and/or permanent changes in taxiing patterns, and changes to aircraft operations.

e. Considerations for planned buildings. When planning on-airport buildings, such as terminal buildings, hangars, snow removal equipment buildings, aircraft rescue and fire

Chapter 2. Design Process › 210. Drainage considerations.

fighting (ARFF) buildings, the existing ATCT site should be evaluated for impacts from the project, such as clear LOS, glare, and smoke or vapor plume.

207. Airport Reference Point (ARP).

The ARP is the geometric center of all usable runways at the airport. The FAA uses the ARP to establish the official horizontal geographic location for the airport. The ARP is normally not monumented or physically marked on the ground. The location of the ARP is computed using runway length and is typically presented for both the existing and ultimate runway lengths proposed for development. This allows the FAA to adequately protect the existing and ultimate airspace surrounding the airport. These computations do not use closed or abandoned areas. The FAA-approved Airport Layout Plan (ALP) shows the ultimate development. If there is no ALP, the ultimate runway lengths are the existing runways plus those which have airspace approval, less closed or abandoned areas. Once the ARP is computed, the only time that a recomputation is needed is when the proposed ultimate development is changed. Refer to AC 150/5300-18 for specific calculation requirements and further guidance.

208. Heliports/helipads.

Refer to AC 150/5390-2 for guidance on helicopter facilities on airports. AC 150/5390-2 provides recommended distances between the helicopter Final Approach and Takeoff Area (FATO) center to runway centerline. Safety area dimensions for helipads are also discussed.

209. Other aeronautical uses on airports.

a. Light sport aircraft and ultralights. Aircraft in this category have a maximum takeoff weight of less than 1,320 lbs (599 kg) and 254 lbs (115 kg) respectively, and a maximum stall speed of not more than 45 knots and 24 knots respectively. Since these aircraft regularly operate on turf runways, follow the guidance in paragraph 314. Otherwise, use the standards in this AC for small aircraft with approach speeds of more than 50 knots, and less than 50 knots, respectively. Refer to AC 103-6 for further guidance.

b. Seaplanes. Refer to AC 150/5395-1.

c. Skydiving. Contact the appropriate FAA Airports office for guidance.

d. Unmanned Aircraft Systems (UAS). Contact the appropriate FAA Airports office for guidance.

210. Drainage considerations.

The objective of storm drainage design is to provide for safe passage of vehicles or operation of the facility during the design storm event. Design considerations are discussed in more detail below. Refer to AC 150/5320-5 for further guidance on the design of storm drainage systems. In addition, storm drainage systems must meet local requirements.

a. Design objectives. The drainage system should be designed to:

(1) Provide for surface drainage by the rapid removal of storm water from the airfield pavement including the drainage of the pavement base or subbase by a subdrain system.

(2) Provide an efficient mechanism for collecting airfield flows and conveying design flows to acceptable discharge points.

(3) Provide levels of storm water conveyance that protect airfield pavements and embankments from damage during large storm water events. Additionally any improvements required for airport operations such as utilities and NAVAIDs should be similarly protected.

(4) Provide for a safe level of operation for both airside and landside ground vehicles.

Continue reading ↓ 120 of 600 passages shown