AC 150/5340-18H Standards for Airport Sign Systems
This Advisory Circular (AC) contains the Federal Aviation Administration (FAA) standards for the siting, design, and installation of signs on airport runways and taxiways.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Standards for Airport Sign Systems Date: September 30, 2024 Initiated by: AAS-100
AC No: 150/5340-18H Change:
1
2
3
Purpose. This Advisory Circular (AC) contains the Federal Aviation Administration (FAA) standards for the siting, design, and installation of signs on airport runways and taxiways.
Cancellation. This AC cancels AC 150/5340-18G, Standards for Airport Sign Systems, dated May 10, 2019.
Applicability. This Advisory Circular (AC) establishes Federal Aviation Administration (FAA) standards and guidelines to ensure uniform application of airfield signs for runways, taxiways, and aprons. This AC does not constitute a regulation and is not legally binding in its own right. It will not be relied upon as a separate basis by the FAA for affirmative enforcement action or other administrative penalty. Conformity with this AC is voluntary, and nonconformity will not affect rights and obligations under existing statutes and regulations, except as described below.
Where applicable, the standards contained in this AC provide an acceptable means of satisfying the requirements of 14 CFR Part 139, Certification of Airports; and the requirements for federally obligated airport operators per Grant Assurance 19 and other applicable Grant Assurances. For all other airport operators, conformity with this AC is recommended. The FAA has determined the standards and guidelines contained in this AC are practices which provide an acceptable level of safety, performance and in support of operations for airfield ground navigation.
1. For certificated airports: If an alternate means of compliance is proposed by an airport operator, the FAA will evaluate the request on a case-by-case basis. If the proposal is found to be acceptable by the administrator, those alternate provisions must be documented in the Airports Certification Manual and the Airport Layout Plan if applicable.
ii
2. For federally obligated airports:
a. Use of these standards and guidelines is mandatory for projects funded under Federal grant assistance programs, including, but not limited to, the Airport Improvement Program (AIP). See Grant Assurance 34 and other applicable Grant Assurances.
b. Use of these standards and guidelines is mandatory, as required by regulation, for projects funded by the Passenger Facility Charge program. See PFC Assurance 9 and other applicable PFC Assurances.
3. The content in this AC has been evaluated for conformity with applicable International Civil Aviation Organization (ICAO) Standards and Recommended Practices (SARPs) in effect at the time of publication, which may further emphasize the importance of conforming with these standards.
4 Background. Airport sign systems provide visual cues to pilots and vehicle operators that enhance safe and efficient movement within the airfield environment. Elevated signs protect aeronautical surfaces and convey ground navigation information that enhances situational awareness when maneuvering on the airfield. The standards of this AC establish uniformity of sign systems throughout the National Airspace System (NAS) for consistent application and interpretation.
Standards of this AC correlate with standards in the following ACs:
• AC 150/5300-13, Airport Design
• AC 150/5340-1, Standards for Airport Markings
• AC 150/5345-39, Specification for L-853, Runway and Taxiway Retroreflective Markers
• AC 150/5345-44, Specification for Runway and Taxiway Signs
5 Principal Changes. This AC change contains the following principal changes:
1. Paragraph 1.4:
a. Implemented new paragraph structure to improve user understanding of content.
b. Added text addressing necessary considerations when planning changes to
taxiway designations. Added emphasis on collaboration and addressing existing problematic taxiway system.
c. Introduced terms for “Primary” taxiways and “secondary” taxiways.
d. Added recommended practice to assign primary taxiways close to the main
terminal with “A” and “B.”
iii
e. Added new section addressing taxiway designation for taxiways between parallel runways.
f. Added new section addressing naming considerations for airports with multiple parallel runways separated by a terminal area.
2. Paragraph 1.5:
a. Implemented paragraph-heading structure to improve user understanding of content.
b. Added clarifying language explaining when holding position signs for runway
ends need to indicate both runway designations.
c. Clarified an elevated sign is standard for each taxiway with a mandatory holding position.
d. Established language addressing sign legend for Land and Hold Short Operation
(LAHSO) when holding point is due to intersecting taxiway.
e. Increased emphasis on confirmation of Approach/Departure surfaces is via an aeronautical study versus solely the information provided within AC 150/5300- 13.
f. Increased emphasis on advance coordination with Air Traffic Control (ATC) Air Traffic Manager (ATM) prior to submitting the aeronautical study to address ATC factors that may influence holding positions for protection of APCH/DEP obstacle clearance surfaces (OCSs).
g. Removed text addressing microwave landing system (MLS) sign legend.
3. Paragraph 1.10:
a. Implemented paragraph-heading structure to improve user understanding of content.
b. Clarified application of destination signs.
c. Clarified the standards for outbound destination signs
d. Clarified the standards for inbound destination signs
e. Expanded the list and description of common destination signs.
4. Paragraph 1.11:
a. Implemented paragraph-heading structure to improve user understanding of content.
b. Clarified left side placement of VSR holding position sign.
c. Updated references to AC 150/5300-13.
d. Established 36 inches (91 cm) above grade as the optimum sign installation
height.
e. Clarified what signage is appropriate for protecting ILS critical areas that intersect a vehicle service road (VSR). Removed reference to L-858R sign.
iv
5. Paragraph 1.14:
a. Implemented paragraph-heading structure to improve user understanding of
content.
b. Added content addressing uniformity of sign size as optimum configuration.
c. Created separate paragraphs for sign selection factors.
d. Added Visual effectiveness of sign.
e. Added text establishing offset distances in Table 1-1 assumes standard taxiway
widths.
f. Added language addressing taxiway entrances exceeding the standard taxiway
widths (Example: DFW).
g. Added language addressing substandard taxiway widths.
h. Added language to paragraph 1.14.7.2 addressing canting of sign inward vs
outward.
i. Added new content in paragraph 1.14.7.3 addressing spacing of consecutive
signs on a taxiway.
6. Paragraph A.2:
a. Implemented paragraph-heading structure to improve user understanding of
content.
b. Revised text for consistency with updated changes in the AC regarding complex
airports.
7. Paragraph A.3:
a. Implemented paragraph-heading structure to improve user understanding of
content.
b. Revised text for consistency with updated changes in the AC regarding airports
with two intersecting runways.
8. Paragraph A.4:
a. Implemented paragraph-heading structure to improve user understanding of
content.
b. Revised text for consistency with updated changes in the AC regarding airports
with a single runway.
9. Added new Figure A-4, Examples: Runway Exit Signs at Opposing Acute Angle Taxiways.
10. Added new Appendix B and new Figure B-1, Figure B-2, Figure B-3, and Figure B- 4.
11. Revised figures to improve clarity and reflect updates.
12. Made minor editorial changes and layout adjustments throughout.
v
6 Implementation. Implement changes addressed by this update upon effective date of this AC and as noted below.
1. Apply current standards for projects involving new construction, rehabilitation, or reconstruction as per the applicability criteria of paragraph 3.
2. For existing non-standard conditions, develop a strategy through the airport planning process as detailed in Chapter 2 of AC 150/5300-13.
3. For existing non-standard conditions at a Part 139 airport discovered as part of an inspection, consult with the assigned airport certification safety inspector to:
a. Ensure the airport certification manual properly documents the nonstandard
condition.
b. Discuss airport’s proposed actions to mitigate or otherwise address any
associated interim risk.
c. Discuss airport’s proposed plan to meet standards.
4. Taxiway Designations. It is not necessary for an airport to take immediate action to correct existing taxiway systems not conforming to paragraph 1.4 naming conventions. Develop a strategy to manage interim risk and to attain standard taxiway designations over time through normal planning processes. As practical, implement changes with an associated airfield re-construction or rehabilitation project. Managed incremental improvements overtime lessens the confusion risk that may temporarily result from change.
5. Departure Area Signs. The recent change to the departure protection surface significantly reduces the surface footprint and thus will likely result in relocation or removal of existing approach/departure holding positions on parallel taxiways. Assess existing taxiway departure holding positions per paragraph 1.5.7.4 and coordinate any change, including removal of existing signs, with the FAA per paragraph 1.5.7.5.
6. Opposing High-speed Taxiway Exits. Where existing high-speed exits have a history of pilot confusion due to proximity of an opposing high-speed exit, implement corrective actions as soon as practical to meet paragraph 1.8.1.2. Refer to the Taxiway and Taxilane Design chapter of AC 150/5300-13 for high-speed exit separation design.
7. Destination Signs. Installation of destination signs are optional based on ground navigation confusion risk. Conform to standards when installing new sign assemblies or replacing existing signs.
8. Vehicle Service Road Signs. Conform to standards when installing new sign assemblies or replacing existing signs. For existing non-standard VSR signs with a history of vehicle operator deviations, take necessary action to correct the nonstandard condition as soon as practical.
9. Using this Document.
vi
Hyperlinks (allowing the reader to access documents located on the internet and to maneuver within this document) are provided throughout this document identified by underlined text. When navigating within this document, return to the previously viewed page by pressing the “ALT” and “ ←” keys simultaneously.
To aid in document navigation, users may add custom bookmarks to the bookmark panel list. Navigate to the location you want to bookmark. Highlight and select the text to appear on the bookmark, then click the “add bookmark” button at the top of the bookmark panel and edit the bookmark text as needed. New bookmarks appear at the end of the bookmark list, but you may drag and drop them to a preferred position.
Figures in this document are schematic representations and are not to scale. Size of signs is exaggerated to aid user viewing.
7 Use of Metrics. This AC uses U.S. customary units followed with “soft” (rounded) conversion to metric units. The U.S. customary units govern.
8 Where to Find this AC. You can view a list of all ACs at https://www.faa.gov/regulations_policies/advisory_circulars/. You can view the Federal Aviation Regulations at https://www.faa.gov/regulations_policies/faa_regulations/.
9 Feedback on this AC. If you have suggestions for improving this AC, you may use the Advisory Circular Feedback form at the end of this AC.
John R. Dermody Director of Airport Safety and Standards
CONTENTS
Paragraph Page
vii
Glossary of Terms … x
Glossary of Sign Types … xii
Chapter 1. Runway and Taxiway Guidance Signs … 1-1
1.1 General … 1-1
1.2 Planning … 1-1
1.3 Components of a Sign System … 1-1
1.4 Developing Taxiway Designations … 1-3
1.5 Mandatory Instruction Signs … 1-10
1.6 Location Signs … 1-18
1.7 Boundary Signs … 1-18
1.8 Direction Signs … 1-19
1.9 Taxiway Ending Marker … 1-21
1.10 Destination Signs … 1-21
1.11 Vehicle Roadway Signs … 1-25
1.12 Information Signs … 1-29
1.13 General Signing Conventions … 1-30
1.14 Sign Size and Locations … 1-33
1.15 Sign Operation … 1-36
1.16 Painted Signs on Pavement … 1-37
1.17 Installation … 1-37
Chapter 2. Runway Distance Remaining Signs … 2-1
2.1 General … 2-1
2.2 Description … 2-1
2.3 Configuration … 2-1
2.4 Sign Operation … 2-2
2.5 Size and Location … 2-2
2.6 Installation … 2-2
Appendix A. Airport Signing Examples … A-1
viii
Appendix B. Specific Signing Scenarios and Details … B-1
FIGURES
Figure 1-1. Example of Taxiway Designations … 1-38
Figure 1-2. Taxiway Designations for Parallel Runways … 1-39
Figure 1-3. Examples of Mandatory Instruction Signs … 1-40
Figure 1-4. Application Examples for Holding Position Signs … 1-41
Figure 1-5. Holding Position Location Relation to Protected Surface … 1-42
Figure 1-6. Runway Location Signs and Arrows on Holding Position Signs … 1-43
Figure 1-7. Examples: Irregular Holding Position Scenarios … 1-44
Figure 1-1 · page 8Picture of the page from the copy saved here
Figure 1-8. Examples of Holding Position Signs at Runway/Runway Intersections … 1-45
Figure 1-9. Sign Applications for ILS Critical Areas … 1-46
Figure 1-10. Examples of Location Signs … 1-47
Figure 1-11. Examples of Boundary Signs … 1-48
Figure 1-12. Example Signage for an Ending Taxiway Intersection … 1-49
Figure 1-13. Examples of Direction Signs, Destination Signs, and Taxiway Ending Marker. 1-50
Figure 1-14. Examples of Signs at a Taxiway/Taxiway Intersection … 1-51
Figure 1-15. Examples of Signs at an Existing Complex Taxiway/Taxiway Intersection … 1-52
Figure 1-16. Service Road Intersecting Runway Safety Area … 1-53
Figure 1-17. Service Road Intersecting Taxiway … 1-54
Figure 1-18. STOP and YIELD Signs … 1-55
Figure 1-19. DO NOT PROCEED Sign Detail … 1-56
Figure 1-20. VOR Receiver Checkpoint Sign … 1-57
Figure 2-1. Runway Distance Remaining Sign … 2-4
Figure 2-2. One-Half Distance Remaining Sign … 2-5
Figure 2-3. Runway Distance Remaining Sign Configurations … 2-6
Figure A-1. Example 1 – Typical Airport Signage … A-2
Figure 1-8 · page 8Picture of the page from the copy saved here
Figure A-2. Example 2: Airport with Intersecting Runways … A-5
Figure A-3. Example 3: Airport with a Single Runway … A-8
Figure A-4. Examples: Runway Exit Signs at Opposing Acute Angle Taxiways … A-9
Figure B-1. Canting Runway Holding Position Sign … B-1
Figure B-2. Angled Runway Holding Positions … B-2
ix
Figure B-3. Substandard Runway Holding Position … B-3
Figure B-4. Insufficient Holdline-Taxiway Separation … B-4
TABLES
Table 1-1. Sign Heights and Location Distances for Taxiway Guidance Signs … 1-36
Table 2-1. Sign Heights and Location Distances for Runway Distance Remaining Signs … 2-3
x
GLOSSARY OF TERMS
This following table lists and defines terms and acronyms used within the document.
Term/Acronym Description
ACM Airport Certification Manual
ACSI Airport Certification Safety Inspector
Alphanumeric A taxiway designation convention consisting of letters and numbers. Alphanumeric designations start with a letter and end with a number.
AOA Air Operations Area. Refer to AC 150/5300-13 for additional information.
APCH/DEP Approach/departure
APS Approach Protection Surface. Refer to AC 150/5300-13.
ATC Air Traffic Control
ATCT Airport Traffic Control Tower
ATM Air Traffic Manager
Bypass Taxiway A secondary taxiway connecting a parallel taxiway to the runway for takeoff operation at a location other than the runway end.
Crossover Taxiway
A secondary taxiway connecting two primary taxiways. As known as a connector taxiway. For example, a short taxiway between two parallel taxiways.
CTAF Common traffic advisory frequency
DPS Departure Protection Surface. Refer to AC 150/5300-13.
EAT End Around Taxiway. See AC 150/5300-13.
Entrance Taxiway Any taxiway that serves to provide entry onto the runway. Entrance taxiways
may serve a dual purpose as an exit taxiway.
Exit Taxiway Any taxiway that serves to provide exit from the runway. Exit taxiways may serve a dual purpose as an entrance or runway crossing taxiway.
FBO Fixed-base operator
xi
Term/Acronym Description
GA General aviation
ILS Instrument Landing System: A precision instrument approach system consisting of electronic components providing vertical and course guidance to a runway.
INTL International
LAHSO Land and Hold Short Operation
MLZ Military Landing Zone
MUTCD Manual on Uniform Traffic Control Device
NAS National Airspace System
OCS Obstacle Clearance Surface. Terminal Instrument Procedures (TERPS) terminology referring to airspace near the runway required to be clear of obstacles for an instrument approach procedure. Reference FAA Order 8260.19, Flight Procedures and Airspace, for additional information. The APS and DPS surfaces of AC 150/5300-13 model the Approach OCS and Departure OCS.
OFZ Obstacle Free Zone. Refer to AC 150/5300-13 for information and details on OFZs.
POFZ Precision Obstacle Free Zone. Refer to AC 150/5300-13 for complete information and detail on POFZs.
Primary Taxiway A functional design grouping describing taxiways interconnecting runways
and other primary taxiways to airside facilities such as terminal areas, aprons, and hangar areas. The designation aligns with terminology within International Civil Aviation Organization (ICAO) Doc 9157, Aerodrome Design Manual. Primary taxiway characteristics include frequent daily use and taxiway lengths allowing sustained taxi speeds. Examples include parallel taxiways, long connector taxiways, high-frequency runway crossing taxiways, and end-around taxiways. The classification is principally for establishing appropriate taxiway designations and has no operational purpose.
Provide The term provide means to furnish and install, complete in place and ready for intended use.
Recommendation/ Recommend
Supplemental measures and guidelines the FAA recognizes as promoting safety, capacity, or efficiency. An airport has the discretion to implement a recommended practice to address a site-specific condition.
xii
Term/Acronym Description
RSA Runway Safety Area. Refer to AC 150/5300-13.
Runway Crossing Taxiway
A primary taxiway that principally serves to taxi aircraft across a runway on a high frequency basis. Aligned secondary taxiways connecting parallel taxiways to a runway do not constitute a runway crossing taxiway.
Runway Safety Surface
A category of various runway areas and zones protecting runway operations. This includes runway safety area, runway object free areas, OFZs, POFZs, ILS critical areas, approach and departure protection surfaces, visual obstacle clearance surfaces, etc.
Secondary Taxiway
A functional design grouping describing taxiways interconnecting a primary taxiway to a runway, other primary taxiway, or an apron area. Secondary taxiway characteristics typically include short lengths and slow taxi speeds. Examples include entrance and exit taxiways, short connectors (aka stub), short crossover taxiways, and bypass taxiways. The classification is solely for establishing appropriate designations.
TERPs Terminal Instrument Procedures. Refer to FAA Order 8260.3, United States Standard for Terminal Instrument Procedures.
TLOFA Taxilane object free area
TOFA Taxiway object free area
VOR VHF omnidirectional range
VSR Vehicle service road
GLOSSARY OF SIGN TYPES
The following are the main categories and brief descriptions of sign types:
Sign Type Brief Description
Boundary Signs Boundary signs identify the location of the boundary of the RSA/OFZ or ILS critical area for a pilot exiting the runway. The sign has a black inscription on a yellow background. See Figure 1-4 and Figure 1-11, details a and b.
Destination Signs A destination sign has a black inscription on a yellow background and always contains an arrow. These signs indicate the general direction to a remote location. See Figure 1-13, details b through d.
xiii
Sign Type Brief Description
Direction Signs A direction sign has a black inscription on a yellow background and always contain arrows. The signs indicate directions of taxiways leading out of an intersection. The signs may also indicate a taxiway exit from a runway. See Figure 1-13, detail a.
Information Signs These signs reside on the airside of an airport and provide information other
than mandatory holding positions, taxiway guidance, and runway distance remaining signs. An information sign has a black inscription on a yellow background.
Location Signs These signs identify the taxiway or runway upon which the aircraft is located. The sign has a yellow inscription with a yellow border on a black background. The yellow border is set in from inner edge of the sign to yield a continuous black margin. See Figure 1-10, details a and b.
Mandatory Instruction Signs
A mandatory instruction sign has a white inscription (legend) with a black outline on a red background. They denote taxiway/runway intersections, runway/runway intersections, ILS critical areas, POFZ boundaries, runway approach/departure areas, CAT II/III operations areas, military landing zones, and no entry areas. See Figure 1-3, details a through e.
Runway Distance Remaining Signs
Runway distance remaining signs provide distance remaining information to pilots during takeoff and landing operations. The sign has a white numeral inscription on a black background. See Figure 2-1 and Figure 2-2.
Taxiway Ending Marker
This marker sign indicates that a taxiway does not continue beyond an intersection. See Figure 1-13, detail e.
Vehicle Roadway Signs
These are signs located on the airfield providing ground navigation cues solely for vehicle operators. See Figure 1-16.
xiv
Page Intentionally Blank
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.3 Components of a Sign System.
CHAPTER 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS
1.1 General. A properly designed and standardized runway and taxiway guidance sign system is essential for the safe and efficient operation of aircraft and ground vehicles on the airport movement area. Essential characteristics of a standard sign system include:
1. Provide the ability to easily determine the designation of any pavement on which the aircraft is located.
2. Readily identify routes toward a desired destination.
3. Indicate mandatory holding positions, including holding positions used to maintain aircraft separation during low-visibility weather operations.
4. Identify boundaries for approach/departure areas, ILS critical areas, the POFZ, and RSA /OFZ.
1.2 Planning. Users of this AC may recognize that the functional layout of each airport is different. Although two airports may have similar runway and taxiway configurations, the number of signs needed to provide the pilot with the necessary taxiway guidance information may differ. Several factors influence this difference such as ground traffic patterns, the presence of an ATCT, the location of terminals, fixed-base operators and other facilities, the number of aircraft operations, and types of operators. In view of the differences in each airport's functional layout, collaborate with the FAA and airport users to ensure development and installation of a runway and taxiway guidance sign system conforming to the standards of this AC as practicable. At Part 139 airports, coordinate all proposed changes to the Airport Signage Plan with the Regional FAA Airport Certification Safety Inspector prior to installation of new signage. Update the ACM as appropriate.
1.3 Components of a Sign System. A standardized system of signs enhances safety at all airports within the NAS. Paragraphs 1.5, 1.6, 1.7, 1.8, 1.9, and 1.10 contain standards for different types of runway and taxiway guidance signs and along with paragraphs 1.13, 1.14, 1.15, and 1.17, provide information on their general signing conventions, size and location, operation, and installation. Figures included in this chapter, as well as Appendix A and Appendix B show graphic depictions of these signs and common applications. The location and types of signs installed as part of a runway and taxiway guidance sign system at a particular airport will vary depending upon functional layouts, as discussed in paragraph 1.2. Apply the following guidelines when designing signs as part of this system at a particular airport:
1.3.1 Install a holding position sign and taxiway location sign at the holding position on any taxiway that provides access to a runway.
1.3.2 When it is necessary to protect a navigational signal, airspace, or the RSA/OFZ, install a holding position sign on any taxiway at the boundary of the ILS critical area, the POFZ, or the runway approach/departure area and, as appropriate, at the CAT II/III operations holding position.
1.3.3 Install a holding position sign on any runway that intersects with another runway.
1.3.4 Install a sign array consisting of taxiway direction signs prior to each taxiway/taxiway intersection where it is normal for aircraft to turn or to hold short of the intersection. The signs in the array include a taxiway designation panel with an arrow for each taxiway where an aircraft might turn or hold short. Include a taxiway location sign as part of the sign array unless determined to be unnecessary, as shown in Figure 1-15. A sign array is not necessary at a taxiway/taxiway intersection where the aircraft turn is restricted, not customary, or would create a hazard such as an intersection between a parallel taxiway and an exit high-speed exit taxiway.
1.3.5 Install a runway exit sign along each runway for each normally used runway exit.
1.3.6 At uncontrolled airports (i.e., airports without an operating ATCT), consider whether it is preferable to substitute destination signs for the signs described in paragraphs 1.3.4 and 1.3.5.
1.3.7 Install standard highway stop or yield signs on vehicle roadways at the intersection of each roadway with a runway or taxiway. See paragraph 1.11 for additional details about the signs and their locations.
1.3.8 Install additional signs on the airfield where they are necessary to eliminate confusion or provide confirmation. For example, it may be necessary to install a taxiway location sign at the entrance to a taxiway from an apron area where several entrances exist. Similarly, on runway exit taxiways where ATC regularly requests pilots to report clear of the runway or where an aircraft regularly stops after clearing the runway, it may be beneficial to install an RSA/OFZ boundary sign to assist the pilot in making this report. At complex intersections or intersections along low visibility routes, it may be beneficial to install location signs on the far side of the intersection so the pilot can confirm the correct taxi path.
1.3.9 For airports certified under Part 139, provide lighted signs for all mandatory instruction signs, location signs, directions signs, and runway distance remaining signs. Refer to §139.311 for regulatory requirements.
1.3.10 For non-139 airports, installation of unlighted signs with retroreflective panel legends may be a more economical option. Consider the number of night operations, available instrument approaches, and the effectiveness of lighted signs versus unlighted retroreflective signs. Lighted signs are generally more discernable at a greater distance than retroreflective signs. If using a mix of lighted and unlighted signs at the airport,
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.4 Developing Taxiway Designations.
place priority on installing lighted signs for all runway mandatory holding position signs.
1.4 Developing Taxiway Designations. The guidelines and standards in this section establish a taxiway naming convention using logical taxiway designations to facilitate efficient ground navigation. Uniformity of taxiway nomenclature between different airports enhances pilot situational awareness for transient pilots unfamiliar with the airport. Application of these principles:
1. Establishes positive identification of location on the airfield enhancing pilot and vehicle operator situational awareness.
2. Provides a clear and logical taxiway system for pilots, controllers, and vehicle operators.
3. Reduces the risk of navigational error that may lead to a runway incursion or surface incident.
4. Establishes uniformity of taxiway designations in the NAS.
1.4.1 Implementing Taxiway Naming Convention. As each airport has varying geometries, space constraints, and operational practices, an airport operator will adapt these guidelines to suit the ground navigational needs of the airport. For most airports, multiple solutions are possible. However, the primary objective remains constant for all airports to establish a clear, logical, and uniform taxiway system that enhances awareness of location on the airfield for pilots and vehicle operators.
The airport planning process is the optimum time to develop a strategy for establishing effective taxiway designations for the airport. Application of a Safety Risk Management process is an effective method to assess risks associated with taxiway designation considerations.
To limit confusion risk for itinerate pilots, taxiway designation design needs to consider uniformity of sign conventions across the NAS versus customizing designations for individual airports.
For new taxiways and airports, the design flexibilities associated with new infrastructure development simplifies design and planning strategies. The degree of adverse effects associated with implementing designations for new taxiways will typically be less than that associated with changing existing designations. Inform the ACSI of the effort to determine their interest in participating. Do not expand application of existing substandard designation practices.
Pilots become accustomed to taxiway systems with existing non-standard or complex taxiway designations even if there is an elevated risk for
ground navigation confusion. Consider the potential for temporary operational disruption any proposed change to existing taxiway designations may create. Extensive changes to an existing taxiway system may cause a temporary state of elevated confusion amongst pilots, controllers, and ground personnel. While pilots, controllers, and vehicle operators eventually acclimate to new taxiway designations, in the short term, there will likely be a state of elevated level of risk for pilot confusion. This temporary risk is not justification to forgo optimization of taxiway designations. Managed incremental change over time minimizes the temporary risk for navigation confusion.
The FAA expects an airport with non-standard or complex taxiway designations with risk for ground navigation confusion to develop a strategy to achieve a standard taxiway system over time. Consider the following factors when deciding to implement a change to existing taxiway designations:
1. Taxiways having a history of pilot confusion or loss of situational awareness.
2. Taxiways the owner plans to reconstruct or rehabilitate.
3. Making incremental changes over time to minimize operations disruption.
1.4.2 General Standards. These standards apply to taxiway designations for all airports.
Keep it simple and logical to facilitate pilot understanding of location awareness.
Use single letters, double letters or alphanumeric designations based upon the type of taxiway (e.g., primary, entrance, exit, connector taxiway, etc.).
Apply a distinguishable pattern when assigning taxiway designations. For contiguous airfield geometries, apply a logical order of letter progression. Examples include east to west, north to south, or clockwise progressions. Figure 1-1 depicts a sequence for the primary taxiways progressing south to north as well as a sequence progressing east to west. For divided airfields such as those with runways separated by a terminal area, the pattern may be a grouping of letters with an identifiable arrangement. For example, apply taxiway designations on one side of the terminal area using letters A though L and on the other side, letters M through Z. The objective is to establish a layout where a pilot, especially a transient pilot, is able to quickly locate a specific taxiway on the airport diagram.
Designate each taxiway segment with a unique designation. Use a designation only once to identify a contiguous taxiway section. Ensure no
separate, distinct taxiway segment has the same designation as another taxiway segment.
Designate secondary taxiways connecting a primary taxiway to a runway with unique alphanumeric designations to facilitate positive location identification on the airfield.
These naming conventions do not apply to taxilanes, terminal gate areas or other apron parking areas. Use a different distinct naming convention for such areas to avoid confusion with ground navigation on the taxiway system. Consider use of inbound destination signs of paragraph 1.10.4 to supplement taxiway direction signs with identifying distinct areas of a complex terminal area.
Refer to paragraph 1.4.4.2 for a permissible exception to this standard for taxiways predominantly used as a crossing taxiway.
1.4.3 Non-standard Designation Practices. The following address non-standard applications that introduce risk to ground navigation of the taxiway system. Do not apply the following:
Use of numbers by themselves for taxiway designations. Pilots may confuse a numeric taxiway designation for a runway designation.
Use of the letters “I” and “O”. Pilots may mistake these letter characters as numerals.
Use of the letter “X”. Pilots may mistake the sign information for a closed taxiway.
A change of taxiway designation without any discernable change in direction or an intersection with another taxiway or runway.
Use of alphanumeric combinations that may create confusion with a runway designation. For example, if an airport has a runway “4L” do not use a taxiway designation of “L4” by skipping the number 4.
Situations where taxiways have similar names as other airfield pavements and areas. For example, having a taxiway C4 designation as well as a terminal gate taxilane C4. Apply a different naming convention for nonmovement area taxilanes that is distinct from the taxiway naming convention.
Designation of taxiways using an adjective descriptor or a physical object such as “inner,” “outer,” “parallel,” and “bridge” taxiways. Such descriptors may not be known to transient pilots resulting in pilot confusion.
Use of double different letter designations. This application in the movement area increases the potential risk for communication confusion between the pilot and the controller. For example, a pilot may interpret a controller instruction for taxiway Alpha-Bravo (TWY AB) to mean taxiway Alpha (TWY A) and taxiway Bravo (TWY B). Refer to paragraph 1.4.5.7 for permissible exceptions for entrance connector taxiways to non-movement area aprons.
1.4.4 Primary Taxiways. Begin assignment of taxiway designations for the airfield system by first identifying and labeling primary taxiways.
Assign single letter designations to primary taxiways using a progressing order or grouping per paragraph 1.4.2.3. Apply double same letter designations (e.g., AA or BB) only after exhausting single letter designations. Optimizing the use of alphanumeric designations for secondary taxiways, such as entrance taxiways, will typically provide sufficient single letter designations for primary taxiways at most airports.
Primary taxiways used principally by local ATC for taxiing aircraft across a runway may retain the same taxiway designation. Taxiway “F” and Taxiway “G” in Figure 1-1 illustrate this situation. This application does not apply to entrance taxiways at runway ends or secondary taxiways occasionally used for crossing traffic across a runway as indicated by Taxiway D3 and Taxiway B3. Coordinate with the facility ATC ATM to establish primary taxiways with predominant use as runway crossing taxiways.
A primary taxiway may include a curved section without a change in designation when the turn leads to another taxiway. In Figure 1-1, the short connector between Taxiways T and A retains the Taxiway “T” designation. If the taxiway turn leads to a runway entrance, apply an alphanumeric designation for the short connector as shown for Taxiway B6.
Recommended Practice. Assign primary taxiways closest to the main terminal area with letter characters early in the alphabet (e.g., Taxiway A, Taxiway B). See Figure 1-1. This practice assists transient pilots with locating the terminal area.
1.4.5 Secondary Taxiways. Assign secondary taxiways using alphanumeric designations. Application of alphanumeric designations promotes positive location identification, reducing the risk for pilot confusion of their position on the airport.
General conventions for designating secondary taxiways.
1. Use alphanumeric designations starting with a letter followed by number.
a. Use the letter of the associated primary taxiway as the base
designation followed by the number (example: Taxiway B2 is the second connector taxiway from the base Taxiway B).
b. Use of three-character alphanumeric designators using two
numerals is acceptable when the number of secondary taxiways connecting to a primary taxiway exceeds nine.
c. For a secondary taxiway connector between two secondary
taxiways, use a double same letter designation based on one the secondary taxiway designation (e.g., TWY CC between TWY C1 and TWY C2 in Figure 1-1).
d. Do not use a letter following the number (e.g., B2A).
2. Establish an increasing order from number one to the highest applicable alphanumeric designation for the associated primary taxiway.
3. The alphanumeric order may skip numbers to align designations with other secondary taxiways or to account for future secondary taxiways provided the number progression remains logical as shown in Figure 1-1 for taxiway A, B, C, and D.
4. Except as noted in paragraph 1.4.6, secondary taxiways with an alphanumeric designation physically connect to the associated base primary taxiway.
5. Establish a distinguishable system that facilitates location on the airfield by applying an alphanumeric designation progression in the same general direction (e.g., North to South) as shown in Figure 1-1.
6. Runway exit taxiways designations generally follow the same alphanumeric sequence applied to the runway entrance taxiways. See Taxiways C3, C5, and B4 in Figure 1-1. Runway exit taxiways providing a frequent taxi path to the terminal area may apply a letter designation in lieu of the alphanumeric designation, subject to coordination with the local ATCT. See high-speed taxiways F and Taxiway G in Figure 1-2.
Assign runway entrance taxiways with alphanumeric designations using the letter designation of the parallel taxiway closest to the runway and applying a progressing numeric order per paragraph 1.4.5.1.
1. All connector taxiways to a runway end are secondary taxiways with alphanumeric designations.
2. Start the alphanumeric designations with number one located at a runway physical end. See Taxiways B1, C1, and D1 in Figure 1-1.
3. Where a primary taxiway intersects a parallel taxiway at a runway end, terminate the primary taxiway designation at the parallel taxiway and assign an alphanumeric designation for connector taxiway segment to the runway as shown for TWY B6 in Figure 1-2.
Runway exit taxiways connecting to a primary taxiway predominantly used as a frequent taxi path to the terminal area may apply the single letter primary taxiway designation in lieu of an alphanumeric designation, subject to coordination with the local ATCT. See exit Taxiway E in Figure 1-1 and Taxiways F and G in Figure 1-2.
For connector taxiways between parallel taxiways, apply the same numeric order established for the opposite sides of the primary taxiways. See taxiways A1, A2, and A4 in Figure 1-1.
1. Where connector taxiways align, apply the same number across the primary taxiways as shown for Taxiway B2 and A2 in Figure 1-1.
2. The alphanumeric letter for the connector taxiway between primary taxiways starts with the letter designation of the primary taxiway farthest from the runway as shown in Figure 1-1.
The same alphanumeric designation may cross the associated primary taxiway where deemed beneficial for ground navigation and there is no potential for pilot confusion. See Taxiway C6 in Figure 1-1.
An alphanumeric designation may not cross a different letter primary taxiway. Example: Taxiway B1 may connect Taxiway B to Taxiway A but may not crossover to the opposite side of Taxiway A.
For connector taxiways between a primary taxiway and an apron area, the complexity of the airport terminal area influences the logical assignment of secondary taxiway designations. Collaborate with key stakeholders to include local pilots, airlines, and the ATC ATM to establish logical designations for entry into an apron area.
1. Use alphanumeric designation based on an apron perimeter taxiway as illustrated by Taxiways T1, T2 and T3 in Figure 1-1.
2. In order to conserve use of single letters for primary taxiways, do not use single letter designation for short apron connector taxiways unless the segment is part of a primary taxiway to the apron area such as Taxiway E in Figure 1-1.
3. Because apron areas may interface with various primary taxiways with different orientations and configurations, it is not necessary for the numeric order of apron connector taxiway to align with the adjacent primary taxiway number order.
4. Use of double-same letters (example: Taxiways AA, BB, and CC) is acceptable provided use is logical.
5. Subject to collaboration with key stakeholders, the letter(s) for the alphanumeric designation for apron entry taxiways may consist of characters describing a readily identifiable area provided there is no risk for pilot confusion with other taxiway designations at the airport such as the following examples.
a. Taxiways T1, T2, and T3 in Figure 1-1 identify the terminal area
connectors.
b. Use of double different letter designations to identify distinct non-
movement areas such as Taxiway SC (South Cargo Area), Taxiway NC (North Cargo area), TA (terminal A), etc.
1.4.6 Taxiways Between Parallel Runways. The configuration and spacing of parallel runways will influence optimization of the taxiway designations serving the area between the runways. The use of single letter designations for primary taxiways and alphanumeric designations for secondary taxiways is typically sufficient for airports with parallel runways.
Parallel Runways Without Parallel Taxiway. For parallel runways with insufficient space for a parallel taxiway, such as runways 18C and 18R in Figure 1-2, designate the connector taxiway as follows:
1. Apply alphanumeric designations as if a parallel taxiway exists, as shown in Figure 1-2 for Taxiways “E1”, “E2”, and “E6”, or
2. Apply single-letter designations, as shown for taxiways “G” and “F” in Figure 1-2, for exit taxiways with predominant use as a common taxi path to the terminal area.
Parallel Runways Sharing Parallel Taxiways. For a parallel taxiway serving two parallel runways, assign different designations to each entrance taxiway to establish a clear differentiation between the two airfield positions. Using the same designation for both runway intersections represents a hazardous situation that may lead to pilot confusion due to similar sounding intersections descriptions. In Figure 1-2, the designations for entrance Taxiways “C6” and “D6” establish distinctive articulation to the similar sounding runways’ designations “18L” and 18C”.
1.4.7 Multiple Parallel Runways Separated by Terminal Area. Airports with multiple parallel runways separated by a terminal area may benefit by strategic naming of taxiways on each side of the terminal. To benefit pilot awareness of location with relation to the terminal, apply distinct taxiway designations on each side
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.5 Mandatory Instruction Signs.
of the terminal. Consider, for example, an airport with multiple north-south runways separated by a terminal area.
Applying lower alphabet designations (e.g., A through F) for the east side primary taxiways and upper alphabet designations (e.g., V-Z) to the west side primary taxiways establishes an intuitive separation that conveys relative position.
Additionally, applying an alphanumeric grid where the southern secondary taxiways commence with the number 1 (e.g., A1, B1, V1, W1) and the northern secondary taxiways have a higher number (e.g., A9, B9, V9, W9) establishes an intuitive order conveying a relative position on the airfield. In all instances, engage key stakeholders per paragraph 1.4.1.1 to determine an optimum taxiway designation strategy.
1.5 Mandatory Instruction Signs. Mandatory instruction signs identify locations where aircraft or vehicles hold, when applicable, prior to entering a protected runway safety surface area or restricted airfield zone. The type of protected safety surface will influence the necessary action of a pilot or vehicle operator. At airports with an operating ATCT, pilots and vehicle operators rely on instructions from the controller for the appropriate action at the holding position. At uncontrolled airports, including nonoperating hours of a part time ATCT, pilots and vehicle operators proceed across these holding positions only after exercising selfvigilance to determine their route ensures adequate separation to arriving or departing aircraft.
1.5.1 Application. Install mandatory instruction signs at locations where any part of an aircraft or vehicle infringes upon a runway safety surface. Refer to Figure 1-5 for relationship between hold sign location and point of infringement for various safety surfaces. Provide an elevated sign for each location. Use of mandatory signs beyond this application represents a non-standard condition. Applicable safety surfaces include the following:
1. RSA boundary
2. OFZ based upon point of infringement
3. Approach/Departure OCS based upon point of infringement
4. POFZ boundary
5. Military landing zones boundary
6. LAHSO location, typically at an RSA boundary with an intersecting runway
7. ILS
a. Signal critical area boundary
b. CAT II/III protected area
8. No-entry area boundary
1.5.2 Characteristics.
Mandatory instruction signs have a white inscription with a black outline on a red background (see Figure 1-3).
The sign inscription denotes the applicable safety surface (e.g., runway designations, ILS, etc.).
Mandatory signs do not include arrows except as noted in paragraph 1.5.3.3.
Refer to paragraph 1.14 for the sign size, legend height, location, and separation distance from pavement edge.
1.5.3 Taxiway/Runway Intersections. Mandatory runway holding position signs demarcate a location on taxiways providing direct access to a runway. At airports with an operating ATCT, pilots and vehicle operators may not cross this holding position without receiving controller clearance. The sign placement protects the most conservative boundary of the following:
1. RSA boundary (see Figure 1-5, detail A).
2. Closest point between an aircraft and the runway centerline where part of the aircraft fuselage infringes upon the ROFZ. (See Figure 1-5, detail B.)
3. The applicable distance resulting from the above sea level elevation adjustment as established within Runway Design Standards Tables in AC 150/5300-13.
The sign inscription is the runway designation numerals separated by a dash as per Figure 1-3, detail a. The arrangement indicates the direction to the corresponding runway threshold. For example, “15-33” indicates the threshold for runway “15” is to the left and the threshold for runway “33” is to the right when facing the runway at the holding position.
The sign at each runway end contains the inscription only for the takeoff runway. At towered airports, include the inscription for both the takeoff runway designation and opposite runway end designation where ATC has an operational need to use the runway end taxiways for high frequency daily crossings. This practice does not apply to runway end taxiway entrances the ATCT occasionally uses to cross aircraft. Consult with the local ATCT ATM to determine the level of operational need.
Apply arrows only if necessary to clarify the orientation of multiple runways that intersect with a common taxiway. See Figure 1-6.
Install holding position signs on left side of a holding position per paragraph 1.14.
Install holding position signs on both sides of a holding position for the following situations:
1. Width of taxiway pavement, including fillet and holding bay pavement, at holding position exceeds 150 feet (45.7 m), as shown in Figure 1-4 and Figure 1-7, detail a.
2. The holding position marking does not extend straight across the holding position, as shown in Figure 1-7, detail c.
3. Holding position locations are within close proximity to a turn making it difficult to view a left side sign, as shown in Figure 1-7, detail b.
4. When recommended under a safety risk assessment action.
Cant (angle) signs inward per paragraph 1.13.14 and Figure B-1 for the following situations:
1. Holding positions immediately following a turn where aircraft does line up perpendicular to the hold line, as shown in Figure 1-7, detail b, and Figure B-4.
2. Holding positions where a hold line is not parallel to the runway centerline resulting in placement of the sign in the RSA, as shown in Figure 1-7, detail c.
3. Where necessary to enhance pilot visibility of sign to improve situational awareness.
1.5.4 Runway/Runway Intersections. Mandatory instruction signs, similar to runway holding position signs, identify the RSA boundary of intersecting runway at runway/runway intersections.
The sign inscription is identical to the signs for runway holding position signs, as described in paragraph 1.5.3.1.
Locate a sign per the applicable runway centerline to holding position separation distance, as established within AC 150/5300-13.
For runways that are 150 feet (45.7 m) or less in width, install one sign on the left side of the runway to identify the intersecting runway. Refer to the 13-31 sign to the left of Runway 9 prior to the intersection with Runway 13-31 in Figure 1-8.
For runways that are more than 150 feet (45.7 m) in width, install holding position signs on both sides of the runway to identify an intersecting runway. Runway 13-31 in Figure 1-8 depicts application of signs on both sides for a 200-ft wide runway.
Install mandatory instruction signs on both sides of the intersecting runway, regardless of width, where ATC operationally closes the runway to arrivals and departures under a letter of agreement with the airport operator for a temporary period to conduct continual taxi operations through the runway/runway intersection. See Figure 1-8 for Runway 27 prior to the Runway 13-31 intersection. Refer to AC 150/5340-1 for guidance on surface marking hold lines at these locations.
1.5.5 Land and Hold Short Operations (LAHSO). A LAHSO holding position identifies a location on the runway where pilots hold short of an intersecting runway, taxiway, or approach/departure area after landing. Establishment of LAHSO involves an ATC letter of agreement and installation of necessary signs, surface markings, and lighting.
For runways with published LAHSO, install signs on both sides of the runway regardless of runway width as depicted in Figure 1-8 for Runway 27 prior to the intersection with Runway 13-31.
The sign inscription for a LAHSO prior to an intersecting runway is the runway designation numerals separated by a dash. The sign inscription for a LAHSO prior to an intersecting taxiway is the taxiway designation letter. See Figure 1-3, detail f.
The sign inscription for a LAHSO prior to intersecting an approach/departure area of a converging non-intersecting runway is the same as for the approach/departure areas. See Figure 1-3, detail c.
Refer to AC 150/5340-1 for guidance on collocating LAHSO holding position signs and surface marking hold lines.
1.5.6 ILS Critical Area/POFZ Boundary. This mandatory holding position sign protects the ILS signal propagation and the airspace immediately prior to the runway threshold when the POFZ is in effect. The associated holding position may reside on a runway entrance taxiway or a parallel taxiway. See Figure 1-4 for an ILS sign application.
The sign inscription for the ILS Critical Area or the POFZ boundary holding positions is the abbreviation “ILS” per Figure 1-3, detail b.
Align front face of holding position sign abeam the pattern B hold line between a point on the outermost parallel line and a point 10 feet (3m) further from the ILS or POFZ boundary. Refer to AC 150/5340-1 for the hold line reference point. Refer to paragraph 1.14.5 for lateral sign location criteria. Refer to AC 150/5340-1 for guidance on surface markings hold lines at these locations.
Where the distance between a runway mandatory holding position marking and the ILS/POFZ holding position marking is 50 feet (15.2 m) or less, place the runway mandatory holding position sign at the location of the ILS/POFZ sign. Omit the ILS legend inscription. See Figure 1-9 for an example.
Provide a sign on both sides of the taxiway when the holding position meets the geometrical configurations described in paragraph 1.5.3.5.
The airport operator initially identifies the ILS critical area and POFZ boundaries for review and concurrence by the responsible FAA Airports office. The FAA Technical Operations Office is responsible for confirming ILS critical area boundaries. The FAA Office of Airports is responsible for confirming POFZ boundaries. To initiate the FAA review, submit an SF-7460-1 form specifically addressing the proposed holding position.
1.5.7 Runway Approach/Departure Areas. This sign protects applicable safety surfaces within a runway approach and departure area. Safety surfaces include RSA, TERPS approach OCS, TERPs departure OCS, and the runway OFZ. Pilots and vehicle operators hold at these locations based upon instructions issued by ATC.
The inscription on this sign includes the applicable runway designations and associated approach/departure area. A dash separates the approach area and the departure area as follows: “## APCH – ## DEP.” See Figure 1-3, detail c.
The order of the inscription is relative to the runway/taxiway intersection orientation. The first inscription is the runway end and protected surface to the left-hand side as one is facing the runway from the holding position. See Figure 1-4 for the holding positions for “33 DEP – 15 APCH” and “15 APCH – 33 DEP”.
Designate the boundaries of the POFZ, approach surface, and departure surface on the airport layout plan using the dimensional values in AC 150/5300-13. These boundaries establish initial study points for the FAA’s evaluation of potential conditional holding positions.
Determination of the potential need for a holding position to protect approach and departure areas occurs under Part 77 aeronautical studies to evaluate infringement by taxiing aircraft of applicable TERPS OCSs. The FAA relies on data provided by the airport to evaluate the initial holding position locations established in paragraph 1.5.7.3. Multiple study points may be necessary to establish the location of conflict for different aircraft types. The relevant data typically includes:
1. Runway instrument procedures and approach minima.
2. Pavement surface elevation data (e.g., threshold, taxiway centerline, etc.) to a 1A survey accuracy (+20 feet horizontal tolerance and +3 feet vertical tolerance).
3. Airfield geometric layout.
4. Tail heights of aircraft expected to use the taxiway, including the critical aircraft and most demanding aircraft.
5. Recommendation: Study the next lowest airplane design group to assess if smaller aircraft can taxi under the affected safety surface that larger aircraft infringe.
For airports with an operating ATCT, coordinate the location of potential holding positions with the facility ATM early in the design phase and prior to submittal of the aeronautical study. This advance coordination is beneficial towards identifying factors that may affect the location or need for a holding position to protect approach and departures areas.
Designing for Protection of Approach/Departure Surfaces
The preferred approach to protect runway safety surfaces is to optimize the airfield geometric layout to avoid points of conflict by applying the design standards of AC 150/5300-13. When non-standard or complex airfield geometries exist, the placement of holding positions on taxiways other than those leading directly to a runway may be necessary to protect safety surfaces. While installation of holding positions establishes an acceptable level of safety, it also has potential to effect the efficiency of aircraft ground movement.
Place priority on designing taxiway systems that prevent aircraft from infringing upon a runway safety surface except when the aircraft is taxiing onto the runway. For runway ends with a displaced threshold or a parallel taxiway extending past the runway end, consider offsetting the parallel taxiway as detailed in the Taxiway and Taxilane Design chapter of AC 150/5300-13 to prevent taxiing aircraft from penetrating an approach protection surface.
Where the aeronautical study of paragraph 1.5.7.4 determines a conflict with a safety surface thus indicating the need for a holding position, assess if there is opportunity to make geometric changes that eliminates the conflict. At airports with an ATCT, coordinate with the facility ATM to assess operational impacts a holding position may present.
Depending on the severity of the infringement and the effect upon ground movement efficiency, FAA may consider actions other than placement of a holding position such as raising approach minimums, conducting collision risk modeling, or issuing a regulatory waiver. Install approach/departure holding positions only after receiving confirmation from the FAA Region/ADO.
Changes at an airport can affect existing protection measures in the approach and departure area. A new evaluation may be necessary if operational changes have the potential to affect existing holding positions for approach or departure surface protection. Such changes include the following:
1. A change to the critical or most demanding aircraft resulting in the need for more restrictive protection or easing of current protections.
2. Revision of existing approaches or development of new approach procedures.
3. Geometric changes to airfield pavement in approach/departure area.
Install a sign on left side of taxiways at locations in the runway approach/departure area prior to where a taxiing aircraft would infringe upon the most conservative safety surface.
1. Except as noted in paragraph 1.5.7.8, the sign protecting the approach and departure areas includes both the approach and departure runway designations even though the most conservative safety surface infringement controls the sign location.
2. Align front face of holding position sign abeam the pattern B hold line between a point on the outermost parallel line and a point 10 feet (3m) further from the Approach/Departure protected area.
3. Refer to AC 150/5340-1 for guidance on surface marking hold lines at these locations.
Airfield geometries and ATC procedures may result in situations where the sign addresses only one of the protected areas. For example, a holding position sign legend may indicate a holding position for only the approach area (## APCH) or the departure area (## DEP). Such situations include:
1. A displaced runway threshold where a taxiway underlies a runway approach area but does not underlie the runway departure area.
2. An infringement only occurs to one of the applicable safety areas thus there is no cause to hold aircraft for both the approach and departure areas.
3. Air traffic management practices may result in a benefit to use separate sign locations for the DEP and APCH legends, subject to concurrence from the facility ATC ATM.
The departure end of a runway is the physical end of the runway pavement. Where taxiways traverse through the safety area off the departure end of a runway, protection of the departure area is necessary regardless of whether the runway has declared distances or published departure procedures.
An approach/departure holding position may exist on runways where maintenance vehicles (e.g., snow removal equipment) or taxiing aircraft will encounter a runway approach or departure OCS. There is no associated surface painted hold line for runway applications.
For locations where the distance between an approach/departure holding position and an ILS critical area or POFZ boundary is 50 feet (15.2 m) or less, provide only the APCH/DEP sign at the location farthest from the runway entrance. See Figure 1-4 for example.
For standard End-Around Taxiways (EATs), approach/departure signs are not necessary as aircraft can taxi without penetrating a protected surface. Approach/departure signs may be necessary for non-standard EATs where aircraft infringe upon an approach or departure safety surface. Refer to AC 150/5300-13 for details on EATs.
1.5.8 CAT II/III Operations. This sign is located where aircraft are to hold on a parallel taxiway during CAT II/III operations to ensure proper aircraft separation.
The inscription is the associated runway designation followed by a dash and the abbreviation “CAT II” for Category II operations or “CAT II/III” for Category II/III operations. See Figure 1-3, detail d.
Provide a sign on both sides of the taxiway when the holding position marking for CAT II/III operations is located in the geometrical configurations described in paragraph 1.5.3.5.
Determine the location of CAT II/III signs through a Part 77 aeronautical study by submitting FAA Form 7460-1 for the tail height of the most demanding aircraft.
Refer to AC 150/5340-1 for guidance on collocating surface marking hold lines at these locations.
1.5.9 Military Landing Zones. This sign identifies a location on a taxiway prior to entering a safety surface of a designated military landing zone.
When a runway designation exists for the landing zone, the sign inscription identifies the runway designation numerals similar to paragraph 1.5.3.1. When a runway designation does not exist for the landing zone, apply the sign inscription “MIL LZ.”
Locate the sign per the applicable runway centerline to holding position separation distance, as established within AC 150/5300-13.
Coordinate MIL LZ sign with the Department of Defense FAA Liaison Detachment and FAA Flight Procedures via a specific Part 77 aeronautical study.
1.5.10 No-Entry Sign. This sign indicates areas on the airfield restricted to aircraft entry.
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.7 Boundary Signs.
The inscription is a circle with a horizontal bar, as shown in Figure 1-3, detail e.
Provide a sign on both sides of taxiway prior to pilot encountering the restricted area. Where a safety assessment justifies only one sign, install the single sign on left side of the taxiway.
Installation of a no-entry sign is acceptable for taxiways exclusively used for one-direction taxi paths, such as a runway exit taxiway. For this application, the no-entry sign does not replace the standard runway/taxiway holding position sign. Locate the no-entry sign on the exit taxiway to warn pilots against turning onto the exit taxiway in the wrong direction.
1.6 Location Signs. Location signs identify the taxiway or runway upon which the aircraft is located. A location sign has a yellow inscription with a yellow border on a black background. The yellow border is set in from the inner edge of the sign to yield a continuous black margin. The location sign does not contain arrows. Location signs include the following:
1.6.1 Taxiway Location Sign. This sign identifies the taxiway on which an aircraft is located. Figure 1-10, detail a, shows a typical sign. Taxiway locations signs may be installed on the back side of a direction sign or a mandatory hold sign.
1.6.2 Runway Location Sign. Install this sign on runways where the proximity of two runways could create confusion, as shown in Figure 1-6, detail b. Also consider installing this sign on runways at runway/taxiway intersections commonly used for intersection takeoffs. Figure 1-10, detail b, shows a typical sign. This sign is located to clearly identify the runways for pilots and only contains the runway designation for the one runway end.
1.7 Boundary Signs. These signs identify the boundary of the RSA/OFZ or ILS critical area for a pilot exiting the runway.
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.8 Direction Signs.
1.7.1 RSA/OFZ and Runway Approach/Departure Boundary Sign. This sign identifies the boundary of the RSA/OFZ or the runway approach/departure area for pilots who are exiting these areas. It has a black inscription that depicts the holding position marking on a yellow background, as shown in Figure 1-11, detail a. The sign is typically used only at controlled airports at the request of the ATCT and is located on taxiways where the controller commonly asks the pilot to report “clear of the runway” or where an aircraft is regularly required to stop upon exiting the runway – see Figure 1-4 for examples. The pilot can use the sign as a guide in deciding when to report back to the controller. Consequently, installation of this sign is not necessary at every runway exit or on taxiways having green/yellow color-coded centerline lights. However, this sign may be useful in areas where it is common for the centerline lights to become obscured by snow or ice.
1.7.2 ILS Critical Area/POFZ Boundary and CAT II/III Operations Sign. This sign identifies either the boundary of the ILS critical area, or the POFZ, or the holding position for CAT II/III operations. The sign has a black inscription that depicts the ILS holding position marking on a yellow background, per Figure 1-11, detail b. Install this sign at controlled airports on taxiways where the controller commonly asks pilots to report, “clear of the ILS critical area” when exiting these areas. The pilot can use the sign as a guide in deciding when to report back to the controller. This sign would not normally be necessary on taxiways having green/yellow color-coded centerline lights but may be desirable in areas where the centerline lights could be obscured by snow or ice. Install this sign only on the back side of an ILS, POFZ, or CAT II/III operations holding position sign (see Figure 1-4 for examples).
1.8 Direction Signs. These signs indicate direction to other taxiways immediately leading out of an intersection. Refer to paragraph 1.13 for criteria associated with collocating direction signs with a location sign.
1.8.1 Applications.
Taxiway Direction Sign. Figure 1-13, detail a, shows a typical taxiway direction sign. Application examples are shown in Figure 1-14, Figure 1-15, and Appendix A, Figure A-1, Figure A-2, and Figure A-3.
1. Install direction signs at taxiway/taxiway intersections where aircraft turns are common and intended.
2. Locate direction signs per paragraph 1.14.7.
3. Where necessary to enhance pilot situational awareness for taxiways crossing a runway (e.g., non-standard Y taxiway configuration), locate signs indicating the direction of a taxiway after crossing a runway on the opposite side of the runway/taxiway intersection.
Runway Exit Sign. Figure 1-13, detail a, shows a typical runway exit sign. Application examples are shown in Appendix A, Figure A-1, Figure A-2, Figure A-3 and Figure A-4.
1. For taxiways intended only as exits from the runway in one direction, such as taxiways located near the end of the runway or exit taxiway intersecting the runway at an acute angle, install signs only for the intended exit direction.
2. Provide exit signs on both sides of the runway at an intersecting taxiway if it is common for aircraft to exit the runway on either side.
3. Locate signs for runway exits prior to the runway/taxiway intersection on the side and in the direction to which the aircraft exits.
4. Where two acute-angle taxiways (i.e., high-speed exits) for opposite direction exits are located near each other (a non-standard condition):
a. Locate runway exit signs prior to the opposing acute-angle taxiway
exit where the point of intersection of the two exit taxiway centerlines exceeds 50 feet (15.2 m) from the runway centerline. See Figure A-4, detail a.
b. Locate runway exit signs between the opposing acute-angle
taxiways where the point of intersection of the two exit taxiway centerlines is 50 feet (15.2 m) or less from the runway centerline. See Figure A-4, detail b.
Application Limitations.
1. Do not collocate direction signs with holding position signs, boundary signs, or destination signs.
2. Do not install direction signs for a taxiway/taxiway intersection on an entrance/exit taxiway between the holding position marking and the runway.
3. Do not “bracket” a runway exit with signs placed before and after the exit.
4. Limit runway exit signs to one arrow for the taxiway designation shown on the sign.
5. Do not install runway exit signs for taxiway exits exceeding a 125degree turn from the runway centerline to limit risk of taxiway excursion.
1.8.2 Characteristics.
1. Direction signs have black inscriptions on a yellow background.
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.10 Destination Signs.
2. Each taxiway designation has one arrow indicating the approximate taxiway direction from the intersection except as noted in line 5.
3. Where a direction sign has more than one taxiway direction sign legend as shown in Figure 1-15, arrange the designations of the intersecting taxiways and respective arrows using a clockwise sequence starting left to right from a point facing the holding position.
4. Orient arrows to align with approximate direction of turn.
a. Apply arrow angle values to match taxiway direction within plus or minus five
degrees.
b. A direction sign panel is not necessary for a straight-ahead taxiway path (e.g.,
less than 25-degree angle turn) unless there is a change in the taxiway designation as shown in Figure 1-14, detail a and detail c.
5. Where a taxiway intersection comprises two crossing taxiways as shown in Figure 1-14, detail a, it is acceptable to use a double arrow direction sign in place of the separate direction sign panels.
6. Where the intersection alignment changes more than 25 degrees, provide an arrow approximating the direction of the taxiway as shown in Figure 1-14, detail b.
7. If the taxiway continues straight ahead (25 degrees or less change in alignment) and the designation of the taxiway changes at the intersection, provide a direction sign with an arrow (see Figure 1-14, detail d).
1.9 Taxiway Ending Marker. A taxiway ending marker sign indicates that a taxiway does not continue beyond an intersection. Install a taxiway ending marker at taxiway T-intersections where there is an elevated risk for a taxiway excursion. It is not necessary to install this sign at intersections with low risk for excursion. The sign is a frangible retroreflective barrier installed on the far side of an intersection if the normal visual cues, such as marking and lighting, are inadequate (see Figure 1-12 and Figure 1-13, detail e). See AC 150/5345- 44, Specification for Runway and Taxiway Signs, for stripe dimensions and additional information.
1.10 Destination Signs. Destination signs provide pilots general direction information to a remote location on the airport. There are two general types of destination signs: 1) outbound, and 2) inbound. Both types of destination signs supplement the standard location and direction signs.
1.10.1 Application. The installation of destination signs is at the discretion of the airport operator with collaboration from the facility ATM when an ATCT is present. Provide destination signs only where standard location and direction signs provide inadequate taxi guidance to a remote area.
Placement. Install destination signs in a location clearly visible to approaching aircraft without obscuring or displacing standard location and direction signs. Where a destination sign precedes a location/direction sign, ensure the location/direction sign is fully viewable from a position on the taxiway centerline 150 feet (45.7 m) in advance of the location/direction sign.
1. Locate destination sign in advance of taxiway/taxiway intersection prior to intended turn.
2. The optimum location for the sign is on the same side of the taxiway as the turn direction.
3. Opposite side installations are acceptable where:
a. Space constraints exists.
b. There are conflicts with location and direction signs.
c. There is little risk for pilot confusion of proper taxi path to
destination.
4. Locate destination sign on far side of a taxiway/taxiway intersection where:
a. There is a “T” intersection as shown in Figure A-3 at the
intersection of Taxiway A and Taxiway B.
b. The path to the destination is straight ahead, or
c. There is insufficient space to place the sign prior to the
intersection.
5. Destination may reside on the backside of a location/direction sign array as shown in Figure A-1 for the INTL sign at the intersection of TWY B and TWY C.
Limitations of Use.
1. Do not install destination signs on runways.
2. Do not collocate destination signs with location, direction, or mandatory instruction signs.
3. Destination signs do not displace or supplant standard location and direction signs.
4. At towered airports, ensure the location and information of a destination sign does not conflict with local ATC operating procedures and practices at the airport.
5. Ensure destination signs identify a single path to the destination area to avoid pilot confusion a dual path sign may cause.
6. Limit application of destination signs to avoid visual cue overload conditions for taxiing pilots.
1.10.2 Characteristics.
Destination signs have a yellow background with black inscription and includes an arrow pointing in the general direction of the destination. See paragraphs 1.10.3 and 1.10.4 for criteria specific to outbound and inbound destination signs. See Figure 1-13, details b and c.
Refer to paragraph 1.14 for sign size location and separation distance from pavement edges.
1.10.3 Outbound Destination Sign. Outbound destination signs identify taxiway directions to departure runways. Install outbound destination signs at locations where standard location and direction signs inadequately identify clear taxi path guidance to a takeoff runway. Typical locations include the beginning of the taxi route from an apron area and at complex taxiway intersections where pilots may become confused about the taxi path to a runway end.
Inscription. The following standards apply when an airport elects to install outbound destination signs.
1. The inscription consists of the departure runway designation and an arrow indicating the direction (see Figure 1-13, detail b).
2. The inscription for a taxi route serving multiple departure runways includes a dot to separate the runway designations (see Figure 1-13, detail c).
3. For destination signs that address different taxi routes to separate runway ends, separate the runway designation panels with a vertical border (See Figure A-3, Intersection of Taxiway A and Taxiway B).
1.10.4 Inbound Destination Sign. Inbound destination signs provide pilots supplemental route information to key destination areas on the airport where the proper path may not be clear to the pilot. While standard direction signs may provide adequate taxi guidance at many airports, at others it may be necessary to provide additional taxi route guidance to distinguish between different apron areas such as terminal apron, general aviation apron, cargo
apron, and military apron. The installation of inbound destination signs is at the discretion of the airport owner. See Figure 1-13, detail d, for a typical sign example.
Inscription. The unique navigation needs of an airport determine the appropriate inbound destination sign inscription. The following standards apply when an airport elects to install inbound destination signs.
1. Use generic terms to describe inbound area; do not use commercial names.
2. Use a minimum of three letters/characters for the inscription to avoid confusion with taxiway designations.
3. Use consistent terms at the same airport versus using two similar terms (e.g., APRON versus RAMP).
4. Where multiple destination areas exist, consider providing additional descriptive signs at points closer to the specific destination area (e.g., North Cargo Apron).
Common Destination Names. Sign inscriptions that are logical and easily understood benefit the situational awareness for based and transient aircraft operators. Common generic names, abbreviations, and descriptive terms for inbound destination signs include:
• APRON – general parking, servicing, and loading areas
o FBO Apron – an apron where itinerant general aviation
operators can park their aircraft and expect to have access to traditional FBO services subject to terms and conditions.
o GA Transient Apron – an apron where itinerant general
aviation operators can park their aircraft without FBO services and subject to terms and conditions.
o GA Tenant Apron – an area designated for parking of based
general aviation aircraft, i.e., tie down area.
o North/South/East/West Apron – an apron designation
describing relative location on the airport
• CARGO – areas set aside for cargo handling
• CIVIL – areas set aside for civil aircraft
• FBO – fixed-base operator
• FUEL – areas where aircraft receive fuel or related services
• INTL – areas set aside for handling international flights
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.11 Vehicle Roadway Signs.
• MIL – areas set aside for military aircraft
o ANG – area reserved for air national guard
o USN – area reserved for US Navy
• PARKING – alternative name for apron area
• PAX – areas set aside for passenger handling
• RAMP – name is synonymous with APRON
• TERM – gate positions at which aircraft loaded or unload passengers and cargo
o North/South/East/West TERM – a terminal designation
describing relative location on the airport
1.11 Vehicle Roadway Signs. These signs provide vehicle operators ground navigation information when driving on VSRs within the AOA. VSR signs are solely for vehicle operators to enhance situational awareness while operating within the AOA. These signs do not provide ground navigation information to pilots.
1.11.1 Intersection of VSR with Runway. These signs provide vehicle operators a visual guidance on where to hold on the VSR prior to entering a protected area of the runway, typically the RSA. At airports with an ATCT, provide three signs to control vehicle entry into the runway environment: 1) STOP sign, 2) DO NOT PROCEED sign, and 3) mandatory runway hold position sign. See Figure 1-16 for the standard configuration.
Locate the VSR holding position at a point clear of the RSA and where the vehicle is clear of the runway OFZ.
1. The optimal location of the vehicle holding position sign and stop line is 2 to 10 feet (0.6 m to 3m) prior to encountering the RSA boundary or point of OFZ infringement.
2. A distance further from the optimal location is acceptable provided there is little risk for vehicle operator confusion related purpose of holding position.
3. Utilize the horizontal configuration where there is inadequate vertical clearance to an aircraft wing overhanging the sign when position the aircraft wheels at the RSA boundary.
4. Refer to the applicable runway centerline to holding position separation distance and OFZ surface criteria as established within AC 150/5300-13.
Install the sign on the left side of the VSR as viewed by the vehicle operator when facing the runway. The standard will remain left side for the runway VSR sign. Right side installations are acceptable where space constraints exist and signs do not present a confusion risk.
1. A left-side VSR sign position optimizes the line of sight to the vehicle operator and aligns with the left-side convention that applies to mandatory airfield signs.
2. A right-side stop sign installation is acceptable where space constraints prevent a left-side installation provided the mandatory sign remains on the left-hand side of the holding position.
3. Existing right-side installations:
a. May remain in place until such time the airport plans to rehabilitate
or replace the existing sign assembly.
b. Take action to install a left-side installation as soon as practical
where there is a history of incursions.
Provide standard highway STOP sign (see Figure 1-18) as shown in Figure 1-16.
1. Optimum sign height is 36 inches (91 cm) above surrounding grade; maximum sign height is 60 inches (152 cm) above surrounding grade.
2. Install signs on breakaway supports conforming to frangibility standards of AC 150/5345-44 as follows:
a. For VSR signs located within 50 feet (15.2 m) of the RSA
boundary where the top of the sign exceeds 36 inches (91 cm) above grade
b. Establish frangibility point no more than 3 inches (7.6 cm) above
surrounding grade.
3. Recommendation: Install all VSR Stop signs, DO NOT ENTER signs, and Yield signs on breakaway supports conforming to MUTCD standards to facilitate ease of replacement when damaged.
At airports with an ATCT, install a DO NOT PROCEED - CONTACT ATC sign per Figure 1-19 in line with the STOP sign. Position the sign below the STOP sign or outboard of the STOP sign, as shown in Figure 1-16. Installing the sign outboard of the STOP sign lowers the overall height of the STOP sign assembly.
1. Install the DO NOT PROCEED sign within 2 to 6 inches (5.5 cm to 15.2 cm) from the STOP sign.
2. For part-time or non-towered airports, modify the inscription of the second line to reflect vehicle operator responsibility to verify local air traffic activity before proceeding such as “Announce to CTAF”.
Provide a standard retroreflective runway holding position sign L-858R, Size 1, Style 4 as shown in Figure 1-16. Refer to AC 150/5345-44 for additional information about unlighted mandatory instruction signs.
1. Install the mandatory holding position sign separately from the STOP and DO NOT PROCEED signs.
a. Arrange the runway designations to indicate the direction towards
the corresponding runway threshold as viewed from the holding position.
b. For a VSR intersecting a RSA beyond the runway end, the
mandatory sign indicates the designation of the appliable runway approach end.
2. Locate a holding position sign outboard of the STOP sign a minimum of 2 feet (0.6 m) from the outermost edge of the STOP sign.
3. The maximum height of a holding position sign is 30 inches (0.9 m) above grade as measured from the top edge of the sign to grade.
1.11.2 Intersection of VSR with Taxiway. These signs provide vehicle operators a visual cue indicating where to hold on the VSR prior to intersecting a taxiway, taxilane or apron area. A properly located vehicle holding position provides standard wingtip clearance between taxiing aircraft and holding vehicles. See Figure 1-17 for an example configuration that uses a STOP sign, DO NOT PROCEED sign, and a taxiway direction sign.
Establish the vehicle holding position sign assembly at a point clear of the associated TOFA to ensure holding vehicles do not conflict with aircraft wings. Refer to AC 150/5300-13 for applicable TOFA dimensional standards.
1. The optimal location of a VSR holding position sign assembly is 2 to 10 feet (0.6 m to 3m) from the TOFA boundary as indicated in Figure 1-17.
2. Distances further from the TOFA boundary are acceptable provided it is clear to a vehicle operator they are holding for a crossing taxiway.
Provide a standard highway STOP sign (see Figure 1-18).
1. Locate sign between 6 to 12 feet from the edge of the roadway on the right side of the holding position when facing the crossing taxiway.
2. A left side installation is acceptable for single lane VSRs where opposing traffic does not block the sightline between the vehicle operator and the sign.
3. Sign height for standard holding locations is 48 to 60 inches from the bottom of the sign to the elevation of nearest edge of road pavement.
4. For signs located within 2 feet of the TOFA/TLOFA, apply a horizontal configuration and limit stop sign height to 36 inches (91 cm) above elevation of nearest edge of TOFA/TLOFA grade.
5. Recommended Practice: Install sign on MUTCD approved breakaway supports for safety of vehicle operator and ease of replacement.
Installation of a YIELD sign in lieu of a STOP sign for VSR holding positions within the non-movement area is acceptable at locations where the risk of conflict with aircraft is low. Ensure the airport’s vehicle operators training program adequately addresses yielding right-of-way to taxiing aircraft.
Where necessary to obtain ATC clearance before proceeding, collocate a DO NOT PROCEED sign with the STOP sign. Position the DO NOT PROCEED sign below or outboard of the stop sign as shown in Figure 1-17. Collaborate with the facility ATM to confirm locations such as an entry point to the movement area and entry into an RSA. Installation of these signs may involve a letter of agreement with the local facility.
At locations where deemed necessary by a safety assessment to enhance vehicle driver situational awareness, install a type L-858Y, size 1, style 4, taxiway direction sign.
1. The taxiway direction sign is a separate assembly located a minimum of 2 feet (0.6 m) outboard from the outermost edge of the STOP/DO NOT PROCEED - CONTACT ATC sign assembly.
2. Limit the sign height to be no greater than 30 inches (0.9 m) above grade (measured from the top edge of the sign to grade).
1.11.3 Intersection of VSR with ILS Critical Area. Where VSRs enter or intersect an ILS critical area, provide a DO NOT PROCEED – CONTACT ATC sign, per Figure 1-19. For non-towered airports, modify the inscription DO NOT PROCEED – ANNOUNCE TO CTAF or similar advisory message. This sign is in addition to the red ILS CRITICAL AREA – KEEP OUT sign the FAA installs for FAA owned facilities. Where a critical area boundary resides within the limits of a RSA, install the VSR sign at a location prior to encountering the RSA boundary.
1.11.4 VSR Information Signs. For other VSR signs the airport operator deems necessary, such as speed limit sign, conform to the current standards in the Federal Highway Administration (FHWA) publication MUTCD for Streets and Highways, available at https://mutcd.fhwa.dot.gov. For dual lane VSR, locate signs on the right side of roadway as viewed by the driver. For single lane VSRs, a left side location is acceptable. Ensure the sign location and
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.12 Information Signs.
size do not create a hazard to aircraft operations, safety surfaces, or air navigational facilities.
1.11.5 General VSR Signage Guidelines.
1. Do not install VSR information signs within a taxiway or runway object free areas.
2. For a single lane VSR, locate the sign on the left side of the vehicle holding position; for a dual lane VSR, locate the sign on the right side of the holding position.
3. Locate the nearest edge of the sign 6 to 12 feet (1.8 m to 3.7 m) from the edge of the VSR pavement.
4. As necessary, make adjustment to the sign location to account for aircraft clearance requirements and the effects of jet exhaust.
5. Provide a sign support sufficient to resist forces from expected wind and jet exhaust.
6. Where necessary to enhance the vehicle operator’s view of a sign legend, the airport operator may cant (angle) the sign assembly inward up to 30 degrees.
1.12 Information Signs. Airfield signs other than mandatory instruction signs, taxiway direction signs, destination signs, and runway distance remaining signs. Examples of information signs include noise abatement procedures, VOR checkpoint signs, or other specialized information for pilots.
1.12.1 Characteristics of Information Sign Information signs have a black inscription on a yellow background. Signs are typically unlighted but may be lighted based on airport operator discretion.
1. Limit sign message to appropriate aeronautical information for pilot awareness.
2. Unless otherwise specified herein, apply FHWA guidelines for character font and height as follows:
a. Font type: Series B 2000 or Series C 2000
b. Character height: minimum 7 inches (17.8 cm), maximum 9 inches (22.9 cm).
3. Furnish signs with retroreflective sheeting conforming to AC 150/5345-44, Specification for Runway and Taxiway Signs.
4. Install signs on frangible couplings per paragraph 1.17.
5. Ensure information signs do not take the appearance of a taxiway direction or destination sign.
6. Refer to paragraph 1.13 for general sign conventions and paragraph 1.14 for sign size and location criteria.
1.12.2 VOR Receiver Checkpoint Sign. This sign has an overall mounting height of not less than 24 inches (61 cm) and not more than 30 inches (76.2 cm). It is located as nearly as practicable on an extension of the VOR Receiver Checkpoint Marking diameter line and faced perpendicularly to the line-of-sight of the viewer in the circle (see Figure 1-20).
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.13 General Signing Conventions.
The inscription on the sign shows the facility identification, channel, radial selected (published) for the check, and the plotted distance from the antenna (when applicable).
The station identification and course numerals are at least 7 inches (17.8 cm) high and the other letters and numerals at least 3 inches (7.6 cm) high.
Install signs in accordance with the height and distance standards in Table 1-1. Figure 1-20 shows an example of this sign. (See AC 150/5340-1, Standards for Airport Markings, paragraph 37, for more details about the VOR Receiver Checkpoint Markings.)
1.13 General Signing Conventions.
1.13.1 Unless otherwise stated, locate signs on the left side of the taxiway as seen by the pilot of the approaching aircraft (see exceptions in paragraph 1.13.2). Where installation of signs occurs on both sides of the taxiway at the same location, the sign faces are identical, except as follows:
Holding position where the taxiway location signs reside outboard of the runway holding position sign, as explained in paragraph 1.13.4.
Where an RSA/OFZ boundary sign resides on the back of a runway hold sign on the right side of an exit taxiway, a taxiway direction sign may be installed on the left side.
1.13.2 Signs may be located on the right side of the taxiway when necessary to meet clearance requirements or where it is impractical to install them on the left side because of terrain or conflicts with other objects.
1.13.3 Some signs may reside on the back side of other signs, although it may result in the sign being on the right side of the taxiway. Signs that may reside on the back side of another side include:
RSA/OFZ boundary signs (see Figure 1-11, detail a), which may be installed on the back of taxiway/runway intersection holding position sign (see Figure 1-4).
ILS critical area boundary signs (see Figure 1-11, detail b), which may be installed on the back of ILS critical area holding position signs (see Figure 1-3, detail b, and Figure 1-4).
Taxiway location signs, which may reside on the back of direction signs when they are installed on the far side of an intersection.
Note: Location signs installed in this manner do not negate the need for location signs installed on the left of the runway holding position sign prior to the intersection.
Taxiway location signs, which may reside on the back of holding position signs (see Figure 1-4, Taxiways A1 and A2).
Destination signs, which may reside on the back of direction signs on the far side of intersections when the destination referred to is straight ahead (see Appendix A, Figure A-1).
1.13.4 Install taxiway location signs collocated with holding position signs for taxiway/runway intersections outboard of the holding position sign (see Figure 1-4, Taxiway A).
1.13.5 Location signs are normally part of a direction sign array, which is located prior to the taxiway intersection. Except for intersections of only two taxiways (see paragraph 1.13.7), the location sign is placed in the array so the designations for all turns to the left are located to the left of the location sign; the designations for all turns to the right or straight ahead, when required (see paragraph 1.13.6), are located to the right of the location sign (see Figure 1-14).
1.13.6 Direction signs have arrows oriented to the approximate direction of the turn. Except as noted in paragraph 1.13.7, each designation appearing in an array of direction signs includes one arrow. A direction sign with an arrow indicating that a taxiway continues straight ahead (25 degrees or less change in alignment at the intersection) is not necessary. Where the intersection alignment changes more than 25 degrees, use a sign with an arrow approximating the direction of the taxiway (see Figure 1-14, detail b). If the taxiway continues straight ahead (25 degrees or less change in alignment) and the designation of the taxiway changes at the intersection, then a direction sign with an arrow is used (see Figure 1-14, detail d).
1.13.7 When a taxiway intersection comprises only two crossing taxiways, it is permissible to use a double arrow direction sign in place of separate direction sign panels (see Figure 1-14, detail a). In this case, the location sign panel is on the left side of the sign array. For this type of installation, the taxiway that the pilot is on may not change designation or alignment (more than 25 degrees) on the other side of the intersection (see Figure 1-14, details b and d).
1.13.8 Position the location sign panel on the left side of the sign array when using a double arrow sign panel, per Figure 1-14, detail a. Location signs may not be a necessary element in all direction sign arrays (see Figure 1-15). Consider all information concerning the intersection when analyzing the need for a location sign. This includes:
• Complexity of the intersection layout.
• Distance from the last location sign.
• Complexity of prior intersections.
• Traffic flow patterns through the intersection.
• Visibility conditions when the intersection is in use.
1.13.9 Limitations.
Do not collocate information signs with mandatory instruction, location, direction, or destination signs.
Do not install signs on the segment of taxiway between the taxiway location/runway holding position sign and the runway.
1.13.10 Delineate each designation and its associated arrow included in a direction or destination sign array from other designations in the array by a black vertical border. When appropriate, a location sign may provide this delineation (see Figure 1-15).
1.13.11 On a sign face, a dot means “and.” It is used on signs where one arrow is common to two designations. For example, if the routes to two different runway ends involve the same taxiways, the runway numbers appearing on an outbound destination sign would be separated by a dot; the directional arrow on the sign face would be applicable to both runway ends. See Figure 1-13, detail c.
1.13.12 Use of a dash only applies to mandatory instruction signs. Apply a dash to separate the designations for opposite runway ends (for example: 18-36) or to separate the runway designation from the abbreviation “APCH” or “DEP”. See Figure 1-3, detail c.
1.13.13 When replacing sign panels due to damage or changing message elements, replace the entire message element. This will avoid panel-to-panel color changes that may be distracting to pilots. See AC 150/5345-44 for additional information about replacement sign panels.
1.13.14 It is acceptable to cant (angle) a sign towards the pilot’s line of vision when necessary to improve the visibility of the sign legend. This situation is illustrated in Figure 1-7, detail b where a pilot would have difficulty seeing the sign on the left due to its proximity to the edge of the parallel taxiway. The back of a canted sign is not available for use because it may not be visible to pilots.
1.13.15 When using two separate signs in an array, do not separate message elements between the two signs. For example, do not locate the arrow for a sign panel on a separate sign in the array. Extension of an existing sign (i.e., physically increase its length by adding modules to it) requires all of the following criteria be met:
• The existing sign meets the applicable standards in AC 150/5345-44.
• The length of the sign (existing plus extension) cannot exceed the maximum overall length limitations per AC 150/5345-44.
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.14 Sign Size and Locations.
• Unless the extension involves the addition of only a location sign, the sign face (existing plus extension) meets the standards for legend, borders, arrows, spacing, and color per AC 150/5345-44.
• The extension meets the electrical and frangibility standards of AC 150/5345-44.
• The separation between individual sign housings meets the requirements in AC 150/5345-44.
1.14 Sign Size and Locations. Refer to AC 150/5345-44 for sign specifications addressing manufacture, font type, character heights, and installation criteria.
1.14.1 Sign Size. Three sizes of signs, based on height, are available for taxiway guidance signs: Size 1, Size 2, and Size 3. Refer to Table 1-1 for sign standards.
1.14.2 Selecting a Sign Size. When selecting a sign size, consider sign clearance, visual effectiveness, space constraints, and operational factors. Apply the same panel size for all signs within the same sign array. To the extent practical, apply uniform sign size for same sign types (e.g. mandatory instruction signs, direction signs, location signs, etc.). This does not preclude installation of a different sign size where taxiway geometry creates space constraints preventing uniformity.
Jet Blast. Consider the effects jet blast may have when selecting a sign size. Larger sign faces encounter larger wind forces than smaller sign faces. Typical areas of concern include taxiway turns, where aircraft commonly use breakaway jet thrust, and operations of large four-engine aircraft.
Snow and Ice Removal Operations. At locations with routine heavy snow and ice events, consider local snow removal operations when selecting a sign size. While larger sign faces remain visible with snow depths, they also experience greater forces from snow displacement activities.
1.14.3 Sign Clearance. Provide a minimum 12 inches (30 cm) of clearance between the top of the sign and any part of the most critical aircraft using the airport, as measured when the aircraft's wheels are at the defined pavement edge (e.g., physical or marked taxiway edge). As necessary to provide clearance, move a sign farther from pavement edge within the distance tolerance of Table 1-1. Evaluate reducing the sign size if the maximum sign distance does not provide the standard clearance.
1.14.4 Visual Effectiveness of a Sign. The ability of the pilot to acquire and recognize the message on a sign during reduced visibility conditions is a key indicator of sign visual conspicuity. Multiple factors influence the visual conspicuity of a sign.
Size of Sign. Large sign sizes allow the pilot to read the sign message from a greater distance than smaller signs. Consider the viewing distance from taxiway centerline when selecting a suitable sign size.
Orientation of Sign Face. The orientation of the sign face relative to the pilot’s or vehicle operator’s position can affect readability. For locations where the angle of the holding position may adversely affect a pilot’s or vehicle operator’s view of the sign face, assess if canting the sign face inward will improve the readability of the sign message. Consider signs angles up to 30 degrees from a pivot point on the sign housing edge closest to the pavement edge. See Figure 1-7 and Figure 1-16 for examples.
Sign Distance from Taxiway Centerline. Installation of signs closer to the taxiway centerline associates the sign with the holding position and benefits pilot recognition of the sign message. A lighted sign provides improved readability of the sign legend over a retroreflective sign. Retroreflective signs require reflection of the light beam spread back to the pilot’s eyes. An excessive sign offset may not reflect sufficient light back to the pilot to recognize the sign legend.
1.14.5 Lateral Location of Sign.
Locate the nearest edge of the sign from the edge of the usable pavement, including fillet pavement, based on the distance tolerances established in Table 1-1. The values represent a perpendicular distance from the defined usable pavement edge, which may be the physical edge or a marked edge. The distance values in Table 1-1 assume standard taxiway widths.
For taxiways exceeding the applicable standard taxiway width, the additional width increases the viewing distance to the sign for the pilot on holding on the taxiway centerline. Excessive distances have potential to diminish the pilots visually recognition of the sign message and sign association with the holding position, especially during low visibility conditions. Apply the following maximum separation distances between the taxiway centerline and the middle of the sign array, excluding any outboard blank sign panels if present. The inability to fit a sign within the minimum edge distance and the maximum taxiway centerline distance is an indicator of non-standard pavement geometry.
Lighted Signs
1. 150 feet (45.7 m) for taxiway location/direction sign arrays.
2. 125 feet (38 m) for mandatory runway holding position signs.
Unlighted Signs 60 feet (18.3 m) for taxiway location/direction sign arrays and mandatory runway holding position signs.
For substandard taxiway widths, locate the sign using standard offset tolerances measured from the theoretical standard taxiway edge.
1.14.6 Runway Holding Positions. Locate the holding position per the applicable “Runway centerline to holding position separation distance” as established within AC 150/5300-13. Use the value for the applicable critical airplane design group of the runway.
Collocate mandatory holding position signs with the Pattern A holding position marking of AC 150/5340-1.
Align front face of holding position sign abeam the pattern A hold line between a point on the outermost parallel line and a point 10 feet (3 m) further from the protected surface boundary (e.g. RSA or OFZ). Refer to AC 150/5340-1 for the hold line reference point.
For taxiways entering a holding position at an angle, locate holding position line so that no part of the holding aircraft infringes upon the protected surface. Because the holding aircraft represents the hazard versus the sign itself, it is acceptable for a sign to reside in the limits of the safety surface provided the sign is frangible. See Figure B-2 for an example of this scenario and Figure B-3 for a substandard approach requiring mitigating controls to be in place.
It is acceptable to horizontally cant (angle) the runway holding position sign inward to improve the pilot’s view of the sign and to keep the sign out of the RSA.
1.14.7 Taxiway Sign Locations.
Locate taxiway location/direction signs prior to a taxiway-taxiway intersection per the applicable “Taxiway Centerline to Fixed or Movable Object” distances established within AC 150/5300-13. Use the value for the applicable critical airplane design group of the crossing taxiway. This provides a visual aid indicating where to hold in order to remain clear of taxiing aircraft. It is acceptable to increase the distance if aircraft with larger wingspans than the critical aircraft use the crossing taxiway.
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.15 Sign Operation.
For taxiway-taxiway intersections where taxiing aircraft frequently encounter another aircraft crossing the intersection, collocate a Pattern C hold line marking per AC 150/5340-1. The sign may reside up to 10 feet (3 m) prior to the hold line marking.
For consecutive sign installations located on the same taxiway (e.g., outbound destination sign prior to a runway holding position sign), provide sufficient sign spacing to permit a pilot to view the second sign in time to properly react, assuming normal taxi speeds. Apply the greatest value of the following:
1. 50 feet (15.2) between signs, or
2. A sign spacing value that allows a pilot to view the second sign from a point on the taxiway centerline 150 feet (45.7 m) prior to a point on the taxiway centerline abeam the second sign.
Table 1-1. Sign Heights and Location Distances for Taxiway Guidance Signs
Sign
Size
Legend
Height [inches (cm)]
Legend Panel
Height [inches (cm)]
Installed
(max.) * [inches (cm)]
Offset distance from usable pavement edge to near side of sign [feet (m)]
1 12 (30) 18 (46) 30 (76) 10-20 (3-6)
2 15 (38) 24 (61) 36 (91) 20-35 (6-10.5)
3 18 (46) 30 (76) 42 (107) 35-60 (10.5-18)
Note 1: Distance from the top of the sign to grade, as measured at the side of the sign that is nearest
to the applicable runway, taxiway, or apron usable pavement. Note 2: Refer to paragraph 1.14.5.3 for substandard taxiway widths. Note 3: Refer to paragraph 1.14.5.2 for maximum lateral offset criteria.
1.15 Sign Operation. For airports with lighted airfield signs, install a power source that ensures consistent illumination when activating each runway/taxiway edge light brightness step. Refer to AC 150/5345-44 for additional information about power sources for illuminating signs.
1.15.1 Design airfield electrical circuits to illuminate the following signs when runway edge lights illuminate:
1. Mandatory signs and taxiway location signs for runway holding positions
2. ILS critical areas (as applicable)
3. CAT II/III mandatory signs (as applicable)
4. Approach/Departure signs (as applicable)
5. Runway exit signs
Chapter 1. RUNWAY AND TAXIWAY GUIDANCE SIGNS › 1.17 Installation.
1.15.2 Design airfield electrical circuits to illuminate the following signs when taxiway edge lights illuminate:
1. Taxiway location and direction signs.
2. Taxiway destination signs.
1.15.3 The simultaneous operation of signs with edge lights in paragraphs 1.15.1 and 1.15.2 does not establish a requirement for signs and edge lights to be on the same circuit. Consider the advantages and disadvantages of a dedicated sign circuit that enables operation of runway signage when placing taxiway edge lighting systems out of service for repair, maintenance, or construction.
1.16 Painted Signs on Pavement. Surface painted signs may supplement elevated signs where taxiway geometries establish a risk for pilot confusion. Surface painted signs do not supplant or serve as an alternative option to elevated mandatory hold position signs or direction signs. See AC 150/5340-1 for standards addressing surface painted signs.
1.17 Installation. Orient signs so that the face is perpendicular to the taxiway or runway centerline taxiway or runway or canted inward per paragraph 1.11.5.
1. Mount signs on stable supports so the top of the sign is level. Suitable foundations include concrete slabs, concrete pile, angle iron stakes, and helical pipe pile. Design the foundation such that the top remains less than 1 inch (25 mm) above the surrounding grade and slopes to promote drainage off the foundation top. Provide sign supports that are frangible no higher than 3 inches (7.6 cm) above surrounding grade.
2. Provide power to the signs through breakaway cable connectors installed within the frangible coupling portion of the sign's mounting legs. Install auxiliary equipment, such as isolation transformers or series circuit power adapter units, below ground level in an L-867 light base. See AC 150/5340-30, Design and Installation Details for Airport Visual Aids, for installation details.
Figure 1-1. Example of Taxiway Designations.
Note 1: In this example, the order of the taxiway designation is south to north and then east to west. Note 2: Taxiways F and G are primary taxiways predominantly used to taxi aircraft across Runway 9-27. Note 3: Taxiway T maintains designation after turn into Taxiway A, per paragraph 1.4.4.3. Note 4: Taxiways B6 and C6 are runway end entrances and thus have alphanumeric designations, per
paragraph 1.4.5.2. Note 5: The short connector taxiway between Taxiway A and Taxiway B near Runway 9 may be a
continuation of Taxiway A.
N
5 2
9 2
Terminal
apron
A
C6 C6
C5
G G G
T
D
D
D1
A1
B
E
B2
D6
D
T B4
T2
A2
E
A4
D5
F F
D3
F
B3
See note 2
See note 3
See note 4
See note 5
27
9
A
No taxi
island
B
C3
B1
A
T1
B6
11
7
E
C
B5 Future
taxiway
T3
F
C
C1
CC
C2
Figure 1-2. Taxiway Designations for Parallel Runways.
Note 1: Entrance taxiways at runway ends are secondary taxiways with alphanumeric designations. Note 2: Alphanumeric designation of secondary taxiways with predominant use as entrance taxiways
Figure 1-2 · page 53Picture of the page from the copy saved here
establishes distance location identification. Note 3: TWY F and TWY G are primary taxiways due to predominant use as exit taxiways path to the
terminal area. Note 4: TWY H is a primary taxiway due to predominant use as runway crossing taxiway. Note 5: TWY A terminates at TWY B to establish alphanumeric designation B2 and B6 for runway entrances
to RWY 18L/36R.
N
Terminal
apron
See note 5
See note 1
See note 2
See note 3
See note 4
E6 D6 C6 B6
G
B5 D5
G
A B C
B3 D3
F F F F
F
E2 C2 B2 D2 A
E1 D1 C1 B1
A
H H H H H
G G G
R C 36 36
l c 81 81 r 81
H
L 36
N
See note 2 See note 2
Figure 1-3. Examples of Mandatory Instruction Signs.
(a) Holding Position Sign
(b) Holding Position Sign for ILS and POFZ
(c) Holding Position Sign for Approach/Departure Areas
(d) Holding Position Sign for CAT II/III Operations
(f) LAHSO Signs for Runway or Taxiway Intersections
(e) No Entry Sign
or
Figure 1-4. Application Examples for Holding Position Signs.
Note 1: Taxiway C does not underlie the Runway 33 departure area. Therefore, this sign does not include the
Figure 1-3 · page 54Picture of the page from the copy saved here
“33 DEP” legend. See paragraph 1.5.7.8. Note 2: The location of a holding position is relative to the point on the aircraft that infringes the surface. For
inclining surfaces, such as an approach surface, the location of the holdline position will likely differ from the location of the infringement point. See Figure 1-5, detail C. Note 3: APCH is the approach protection surface and DEP (Sec.1) is section 1 of the two-section departure
protection surface. Note 4: Provide CAT II/III holding position where needed, per paragraph 1.5.8.
ILS ILS
APCH
APCH
DEP (Sec. 1)
DEP (Sec. 1)
RSA
RSA RSA
RSA RSA
ILS
Note 1
Note 4
Note 2
Note 3
Figure 1-5. Holding Position Location Relation to Protected Surface.
5
5
5
Location of holding position
Approach or Departure
Protection Surface
(c) Approach/Departure Protection Surface
Point of infringement
To runway
Runway obstacle free zone
Point of OFZ infringement
Location of holding position Boundary of runway safety area (b) Runway obstacle free zones
Runway Safety Area
or ILS Critical Area
Boundary of protected area
Point of infringement
Figure 1-5 · page 56Picture of the page from the copy saved here
Continue reading ↓ 120 of 158 passages shown