Radar Vectors
Advisory Circular Current Issued Aug 16, 2024 AAS-100 413 pages Copy saved Nov 18, 2026

AC 150/5300-13B Airport Design - Change 1

This AC contains the Federal Aviation Administration’s (FAA) standards and recommendations for the geometric layout and engineering design of runways, taxiways, aprons, and other facilities at civil airports. This substantial revision fully incorporates all previous changes to AC 150/5300-13A as well as new standards and technical requirements. AC 150/5300-13B cancelled the following Engineering Briefs (EBs): EB 63B - Taxiways for Airbus A380 Taxiing Operations EB 73 - Use of Non-Standard 75-Foot- (23-M) Wide Straight Taxiway Sections for Boeing 747-8 Taxiing Operations EB 75 - Incorporation of Runway Incursion Prevention into Taxiway and Apron Design EB 78 - Linear Equations for Evaluating the Separation of Airplane Design Groups on Parallel Taxiways and Taxiways to Fixed/Movable Objects EB 99A - Changes to Tables 3-2 and 3-4 of Advisory Circular 150/5300-13A, Airport Design EB 100A - Holding Position Sign and Marking for Runway Approach/Departure Areas Change 1 cancels the following Engineering Briefs (EBs): EB 65A - Use of 150-Foot (45-M) Wide Runways for Airbus A380 Operations EB 74A - Use of 150-foot (45-M) Wide Runways and Blast Pads for Boeing 747-8 Operations

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Airport Design Date: August 16, 2024 Initiated By: AAS-100

AC No: 150/5300-13B Change: 1

1 Purpose. This Advisory Circular (AC) contains the Federal Aviation Administration’s (FAA) standards and recommendations for airport design.

2 Applicability. No change to paragraph 3, Applicability, dated 3/31/2022.

3 Principal Changes. This AC change incorporates the following principal changes:

1. Added the touchdown zone definition to paragraph 1.5 as item 99, and the V1 definition as item 100.

2. Simplified Figure 1-1, Taxiway Design Groups, and added Table 1-4 to clarify.

3. Updated paragraph 1.12, Related Documents and Federal Regulations.

4. Clarified paragraph 2.4, Addressing Non-standard Airport Conditions.

5. Clarified paragraph 2.6.1, Critical Aircraft.

6. Expanded paragraph 2.7.2, Wrong Surface Events.

7. Updated paragraph 2.10.6.5. The main point of contact for reviews of operations within the non-paved area of the RSA is now the Flight Procedures and Airspace Group.

8. Replaced and cancelled Engineering Brief (EB) reference in paragraphs 3.6.1.2 and 3.6.2.3.

9. Added a note to Table 3-2 to clarify guidance for circling-only approaches.

10. Clarified footnotes for Figure 3-17, Table 4-2, Figure 4-10, Figure 4-12, Figure 4-13, Figure 4-14, Figure 4-15, Figure 4-22, Figure 4-23, and Figure 4-24.

11. Expanded paragraph 3.9.3, Simultaneous Instrument Flight Rules (IFR) Arrival Operations.

12. Clarified paragraph 3.11.4.2.

8/16/2024 AC 150/5300-13B Chg 1

ii

13. Adjusted precision obstacle free zone on Figure 3-25.

14. Added exception to paragraph 3.12.1, items 4.c and 4.e.

15. Clarified paragraph 4.2.

16. Added design considerations to paragraph 4.4.

17. Clarified paragraph 4.7.1, item 1.

18. Expanded paragraph 4.7.2.

19. Clarified paragraph 4.7.3, item 3.

20. Clarified paragraph 4.8.2.1, item 1.

21. Deleted Table 4-3, Dimensions for Runway Entrance/Exit Taxiways with TDG 1A, 1B, 2A, or 2B (Where the Two 90-Degree Turns are Non-standard).

22. Deleted Table 4-4, Dimensions for Runway Entrance/Exit Taxiways with TDG 3, 4, 5, or 6 (Where the Two 90-Degree Turns are Non-standard).

23. Revised paragraph 4.8.5, High-Speed Exit Taxiways.

24. Clarified the two design scenarios for paragraph 4.8.6, Crossover Taxiways.

25. Deleted Table 4-6, Crossover Taxiways with Direction Reversal Between Taxiways Based on TDG.

26. Deleted Table 4-7, Crossover Taxiways with Direction Reversal Between Taxiways Based on ADG.

27. Clarified standards for End-Around Taxiways (EATs) in paragraph 4.12.1.1 and paragraph D.1.4.

28. Clarified standards for apron taxilanes in paragraph 5.4.1.1.

29. Clarified standards for air operations area vehicle service roads in paragraph 6.5.2.

30. Clarified standards for perimeter security roads in paragraph 6.5.4.

31. Clarified standards for navigational aid access roads in paragraph 6.5.5.1.

32. Expanded Table 6-1 and related notes.

33. Revised paragraph D.1.3, Visual Screen Vertical Dimension Calculation, and paragraph D.1.4, Visual Screen and Vertical Elevation Difference.

34. Revised runway, shoulder, and blast pad widths for ADG-VI in Table G-12 and added footnote 14. Appended footnote 12.

35. Deleted items 1, 3, and 4 from paragraph H.4.1, and Figures H-2 and H-3.

36. Updated tables in paragraph J.3 and clarified notes.

37. Clarified paragraph J.4.2.

38. Added paragraph J.4.3, Example: Critical Aircraft TOFA Calculation.

39. Clarified Figure J-14 and Figure J-15.

8/16/2024 AC 150/5300-13B Chg 1

iii

40. Updated Figure J-30 and paragraph J.5.15 to include additional common mitigation.

41. Made minor editorial changes and layout adjustments throughout.

4 Implementation. Implement changes addressed by this change upon effective date of this AC.

5 Feedback on this AC. If you have suggestions for improving this AC, you may use the Advisory Circular Feedback form at the end of this AC.

John R. Dermody Director of Airport Safety and Standards

iv

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Consolidated AC includes Change 1

Subject: Airport Design Date: 3/31/2022 Initiated By: AAS-100

AC No: 150/5300-13B Change:

1 Purpose. This Advisory Circular (AC) contains the Federal Aviation Administration’s (FAA) standards and recommendations for airport design.

2 Cancellation. This AC cancels AC 150/5300-13A, Airport Design, dated September 28, 2012.

3 Applicability. The FAA recommends using the standards and guidelines in this AC for application at civil airports. This AC does not constitute a regulation, is not mandatory, and is not legally binding in its own right. It will not be relied upon as a separate basis by the FAA for affirmative enforcement action or other administrative penalty. Conformity with this AC is voluntary, except for the projects described in subparagraphs 3 and 4 below:

1. Use of these standards and guidelines are practices the FAA recommends for establishing an acceptable level of safety, efficiency, and capacity when designing and implementing airport development projects at civil airports.

2. This AC provides one, but not the only, acceptable means of meeting the requirements of 14 Code of Federal Regulations (CFR) Part 139, Certification of Airports.

3. Use of these standards is mandatory for projects funded under certain Federal grant assistance programs including, but not limited to, the Airport Improvement Program (AIP). See Grant Assurance #34. Airport sponsors should familiarize themselves with the obligations and assurances that apply to each grant program from which they obtained grant funds.

4. This AC is mandatory, as required by regulation, for projects funded by the Passenger Facility Charge (PFC) program. See PFC Assurance #9.

v

4 Related Documents. Refer to paragraph 1.12 for documents referenced by this AC. ACs and FAA Orders referenced in the text of this AC do not include a revision letter, as they refer to the latest version.

5 Principal Changes. This AC incorporates the following principal changes:

1. Restructured the entire document, locating design standards in the chapters with supporting information in the Appendices. Chapters and Appendices are organized and updated as follows:

a. Chapter 1, Introduction:

i. Added new paragraphs explaining the meaning of terms for:

1. Standard, paragraph 1.2.1.1.

2. Recommended Practice, paragraph 1.2.1.2.

3. Requirement, paragraph 1.2.1.3.

ii. Added or revised definitions in paragraph 1.5:

1. Commercial Service Airport, item 27.

2. Critical Aircraft, item 29.

3. Parallel Taxiway, item 72.

4. Runway Visual Range, item 84.

5. Taxiway Centerline, item 92.

iii. Separated Taxiway Design Group (TDG) 2 into TDG 2A and TDG 2B in

Figure 1-1 and related discussions and tables throughout this document.

iv. Removed TDG 7 and revised Main Gear Width (MGW) dimensions for

TDG 5 and TDG 6 in Figure 1-1 and related discussions and tables throughout this document.

v. Moved Instrument Flight Procedures to new Appendix K.

b. Chapter 2, Design Principles (formerly Design Process):

i. Expanded discussion for design process in paragraph 2.6, and visibility minimums in paragraph 2.6.2.

ii. Added paragraph 2.7.2 on Wrong Surface Event.

iii. Expanded latter portion of chapter to include discussions on Modification

of Standards in paragraph 2.8, Safety Management System (SMS) in paragraph 2.9, and Diverse Aeronautical Uses of Airports (operations in the Runway Safety Area (RSA)) in paragraph 2.10.

iv. Expanded guidance and information related to diverse aeronautical uses

on airports in paragraph 2.10.

vi

v. Moved Table 2-1, Changes in Airport Design Standards Associated with

an Upgrade in the First Two Components (Aircraft Approach Category (AAC) and Airplane Design Group (ADG)) of the Runway Design Code (RDC); Table 2-2, Changes in Airport Design Standards Associated with Lowering the Third Component (Approach Visibility Minimums) of the Runway Design Code (RDC); and Table 2-3, Aircraft Characteristics and Design Components to new Appendix M.

c. Chapter 3, Runway Design:

i. Moved Crosswind Component table to Appendix B.

ii. Moved runway historical and background information to Appendix I.

iii. Moved Declared Distance information to Appendix H.

iv. Moved Approach and Departure Reference Code information to

Appendix L.

v. Revised approach and departure tables in paragraph 3.6.

vi. Updated approach surface discussion in paragraph 3.6.1 and added new

approach and departure surfaces Figure 3-5, Figure 3-6, and Figure 3-7.

vii. Updated departure surface to reflect forthcoming Terminal Instrument

Procedures (TERPS) criteria in paragraph 3.6.2 and revised approach and departure surface values in Table 3-2, Table 3-3, Table 3-4, and Table 3-5.

viii. Expanded departure surface guidance in paragraph 3.6.2 and added new

departure area surface Figure 3-9, Figure 3-10, and Figure 3-11.

ix. Added new paragraph 3.7.5 on overlapping RSAs.

x. Expanded Line of Sight (LOS) discussion in paragraph 3.8.

xi. Added new paragraph 3.9 on Parallel Runway Separation.

xii. Added new Figure 3-33 and expanded discussion on transverse slopes in

paragraph 3.16.2.

xiii. Expanded and split Table 3-3, Transverse Grades, into Table 3-6,

Transverse Grades Based on AAC, and Table 3-7, Transverse Grades Based on ADG.

xiv. Expanded turf runway discussion in paragraph 3.16.6.

xv. Removed Interactive Table 3-5, Runway Design Standards Matrix. This is

available online as a design tool at https://www.faa.gov/airports/engineering/airport_design/.

xvi. Added new Table 3-1 to facilitate locating runway design standards in

Appendix G based on AAC and ADG.

d. Chapter 4, Taxiway and Taxilane Design:

i. Reduced dimensions for taxilane object free area (TOFA) and taxiway separation (taxiway separation, taxiway centerline to fixed or moveable

vii

object, and wingtip clearance) as described in paragraph 4.5 and shown in revised Table 4-1. Revised these same standards for taxilanes.

ii. Updated Table 4-2; Taxiway Edge Safety Margin (TESM) for TDG 5 and

TDG 6 is now 14 ft (4.3 m).

iii. Updated taxiway turn and intersection criteria in paragraph 4.7.3.

iv. Updated Taxiway Fillet Design Tool with new criteria. This is available

online as a design tool at https://www.faa.gov/airports/engineering/airport_design/.

e. Chapter 5, Aprons:

i. Expanded discussion on types of aprons in paragraph 5.2.

ii. Moved information on bridges to Chapter 6.

f. Chapter 6, Airfield Systems and Facilities (formerly Chapter 6, Navigation Aids (NAVAIDs) and On-airport Air Traffic Control Facilities (ATC-F)):

i. Consolidated information on NAVAIDs (Communications, Navigation, Surveillance and Weather (CSWN)) from other chapters.

ii. Contains information on systems and facilities only as it relates to airport

design.

g. Removed former Chapter 7, Airfield Bridges and Tunnels.

h. Appendix A (formerly Appendix 1), Aircraft Characteristics:

i. Added new Figure A-3 on folding wingtip aircraft.

i. Appendix B (formerly Appendix 2), Wind Analysis:

i. Relocated Table B-1 on crosswind component from former Chapter 3.

j. Appendix D (formerly Appendix 4), End-Around-Taxiway (EAT) Screens:

i. Added evaluation by licensed engineer to establish structural integrity of the EAT Screen.

k. Appendix E (formerly Appendix 5, General Aviation Aprons and Hangars),

General Aviation Facilities:

i. Relocated information from various areas of document on general aviation (GA) facilities to this appendix.

l. Appendix F (formerly Appendix 6, Compass Calibration Pad), Compass Calibration Pad Survey:

i. Consolidated information into this appendix.

ii. Moved runway historical and background information from former

Chapter 3.

iii. Added Runway Object Clearing information.

viii

m. New Appendix J (formerly Appendix 8, Taxiway Fillet Design), Taxiway

Additional Information:

i. Describes examples of taxiway designs with elevated safety risks.

ii. Removed TDG 7. Separated TDG 2 into TDG 2A (Table J-3) and TDG

2B (Table J-4) and included these additional fillet design dimensions.

iii. Added paragraph J.4 containing a description of the methodology and

calculations used for reductions in taxiway standards.

iv. Added reference to the Taxiway Fillet Design Tool available online at

https://www.faa.gov/airports/engineering/airport_design/.

n. New Appendix L, Approach and Departure Reference Codes, containing

former paragraph 323, Approach and Departure Reference Codes, and updated as follows:

i. Developed new Figure L-1 for ADG V-VI Departures.

ii. Updated Table L-1 on approach reference code.

iii. Relocated information from former Chapter 3.

2. Revised and updated figures throughout.

3. Updated the format of the document in this version and made minor editorial changes throughout.

6 Using this Document. Hyperlinks (allowing the reader to access documents located on the internet and to maneuver within this document) are provided throughout this document identified by underlined text. When navigating within this document, return to the previously viewed page by pressing the “ALT” and “ ←” keys simultaneously.

To aid in document navigation, users may add custom bookmarks to the bookmark panel list. Navigate to the location you want to bookmark. Highlight and select the text to appear on the bookmark, then click the “add bookmark” button at the top of the bookmark panel and edit the bookmark text as needed. New bookmarks appear at the end of the bookmark list, but you may drag and drop them to a preferred position.

Figures in this document are schematic representations and are not to scale.

7 Use of Metrics. Throughout this AC, U.S. customary units are used followed with “soft” (rounded) conversion to metric units. The U.S. customary units govern.

8 Where to Find this AC. You can view a list of all ACs at https://www.faa.gov/regulations_policies/advisory_circulars/. You can view the FAA Regulations at https://www.faa.gov/regulations_policies/faa_regulations/.

ix

9 Feedback on this AC. If you have suggestions for improving this AC, you may use the Advisory Circular Feedback form at the end of this AC.

/signed/

John R. Dermody Director of Airport Safety and Standards

CONTENTS

Paragraph Page

x

CHAPTER 1. Introduction … 1-1

1.1 Policy … 1-1

1.2 Standards, Recommended Practices, and Requirements … 1-1

1.3 Federal Regulations … 1-2

1.4 Environmental Protection … 1-3

1.5 Definitions … 1-3

1.6 Categories and Codes … 1-12

1.7 Airport Layout Plan (ALP) … 1-15

1.8 Airport Data … 1-16

1.9 Airport Improvement Program (AIP) … 1-18

1.10 State Role … 1-18

1.11 Local Government Role … 1-19

1.12 Related Documents and Federal Regulations … 1-19

CHAPTER 2. Design Principles … 2-1

2.1 General … 2-1

2.2 Airport Planning Relationship to Airport Design … 2-1

2.3 Present Needs Versus Future Demand … 2-1

2.4 Addressing Non-standard Airport Conditions … 2-2

2.5 New Construction, Reconstruction, and Rehabilitation … 2-2

2.6 Design Process … 2-2

2.7 Key Safety Considerations for Airport Design … 2-5

2.8 Modification of Standards … 2-6

2.9 Safety Management Systems (SMS) … 2-7

2.10 Diverse Aeronautical Activities on Airports … 2-7

CHAPTER 3. Runway Design … 3-1

3.1 General … 3-1

3.2 Runway Design Code (RDC) … 3-1

3.3 Runway Design Standards … 3-1

3.4 Runway Design Concepts and Considerations … 3-3

Paragraph Page

xi

3.5 Runway End Siting Criteria … 3-6

3.6 Approach and Departure Surfaces … 3-9

3.7 Runway Geometry … 3-20

3.8 Runway Line of Sight (LOS) … 3-24

3.9 Parallel Runway Separation … 3-29

3.10 Runway Safety Area (RSA) … 3-35

3.11 Obstacle Free Zone (OFZ) … 3-38

3.12 Runway Object Free Area (ROFA) … 3-47

3.13 Runway Protection Zone (RPZ) … 3-48

3.14 Clearway … 3-52

3.15 Stopway … 3-53

3.16 Surface Gradient … 3-54

3.17 Runway to Taxiway Separation … 3-64

3.18 Runway to Hold Line Separation … 3-65

3.19 Runway to Aircraft Parking Area Separation … 3-65

3.20 Turf Runways … 3-65

3.21 Markings/Lighting/Signs … 3-67

CHAPTER 4. Taxiway and Taxilane Design … 4-1

4.1 General … 4-1

4.2 Taxiway Design Group (TDG) … 4-2

4.3 Taxiway and Taxilane Design Concepts and Considerations … 4-2

4.4 Straight Segment Taxiway/Taxilane Width … 4-8

4.5 Taxiway/Taxilane Clearance … 4-9

4.6 Parallel Taxiways … 4-17

4.7 Taxiway Fillet Design … 4-19

4.8 Runway/Taxiway Intersections … 4-23

4.9 Holding Bays for Runway Ends … 4-36

4.10 Taxiway Turnarounds … 4-38

4.11 Apron Taxiways and Taxilanes … 4-39

4.12 End-Around Taxiways (EAT) … 4-39

4.13 Taxiway and Taxilane Shoulders … 4-42

4.14 Surface Gradient for Taxiways, Taxilanes, and TSAs … 4-43

Paragraph Page

xii

4.15 Taxiway Line of Sight (LOS) … 4-47

4.16 Markings/Lighting/Signs … 4-47

CHAPTER 5. Aprons … 5-1

5.1 General … 5-1

5.2 Apron Types … 5-1

5.3 Apron Design Concepts and Considerations … 5-3

5.4 Apron Location … 5-4

5.5 Runway Access from Aprons … 5-5

5.6 Lateral Object Clearance on Aprons … 5-6

5.7 Apron Taxilanes … 5-8

5.8 Fueling on Aprons … 5-8

5.9 Apron Surface Gradients … 5-9

5.10 Apron Drainage … 5-10

5.11 Apron Snow Removal … 5-12

5.12 Apron Markings … 5-13

5.13 Apron Signage and Edge Lighting … 5-14

5.14 Area Lighting on Aprons … 5-14

5.15 Apron Security … 5-15

5.16 Apron Pavement Design … 5-15

5.17 Jet Blast and Propeller Wash on Aprons … 5-16

5.18 Airport Traffic Control Tower (ATCT) Visibility/Line of Sight (LOS) on Aprons … 5-18

5.19 Apron Vehicle Service Road (VSR) … 5-19

5.20 Design of Specific Apron Types … 5-20

CHAPTER 6. Airfield Systems and Facilities … 6-1

6.1 General … 6-1

6.2 Airfield Bridges and Tunnels … 6-1

6.3 Airfield Drainage … 6-5

6.4 Airfield Pavements … 6-6

6.5 Airfield Roadways … 6-6

6.6 Blast Fences … 6-10

6.7 Buildings within AOA … 6-12

Paragraph Page

xiii

6.8 Security of Airports … 6-13

6.9 Compass Calibration Pad … 6-16

6.10 Underground Power, Control, and Communications Cables … 6-19

6.11 Communications, Navigation, Surveillance and Weather (CNSW) and Air Traffic Control (ATC) Facilities and Equipment … 6-21

Appendix A. Aircraft Characteristics … A-1

A.1 Basic Aircraft Characteristics … A-1

A.2 Background … A-2

A.3 Aircraft Arranged by Aircraft Manufacturer, and Runway Design Code (RDC) … A-3

Appendix B. Wind Analysis … B-1

B.1 Objective … B-1

B.2 Coverage and Orientation of Runways … B-1

B.3 Allowable Crosswind Components … B-2

B.4 Wind Data Sources … B-3

B.5 Analyzing Wind Data … B-5

Appendix C. Jet Blast and Propeller Wash … C-1

C.1 Introduction … C-1

C.2 Aircraft Generated Air Currents … C-1

C.3 Propeller Wash … C-2

C.4 Jet Blast … C-2

C.5 Recommended Practices … C-4

C.6 Design Considerations … C-4

C.7 Mitigation Measures … C-5

Appendix D. End-Around Taxiway (EAT) Visual Screens … D-1

D.1 Screen Sizing … D-1

D.2 Screen Construction … D-4

Appendix E. General Aviation (GA) Facilities … E-1

E.1 Background … E-1

E.2 General Aviation Apron … E-1

E.3 Hangars … E-11

E.4 GA Terminal Building … E-14

Paragraph Page

xiv

E.5 Airport Support Facilities … E-15

E.6 Fencing for GA Airports … E-18

Appendix F. Compass Calibration Pad Survey … F-1

F.1 Survey of the Compass Calibration Pad … F-1

F.2 Resurvey of In-service Pads … F-1

Appendix G. Runway Design Standards Tables … G-1

Appendix H. Declared Distances … H-1

H.1 Application … H-1

H.2 RSA, ROFA, and RPZ Lengths and Related Nomenclature … H-2

H.3 Background … H-3

H.4 For Takeoff … H-4

H.5 For Landing … H-14

H.6 Notification … H-19

H.7 Documenting Rationale for Declared Distances … H-21

Appendix I. Runway Additional Information … I-1

I.1 Purpose … I-1

I.2 Additional Information and Guidance on Runway Safety Area (RSA) Development … I-1

I.3 Runway Protection Zone (RPZ) Background … I-2

I.4 Using a Runway as a Taxiway … I-3

I.5 Object Clearing … I-3

I.6 Threshold Displacement … I-4

I.7 Overlapping RSAs … I-5

I.8 Runway Object Free Area (ROFA) Background … I-6

Appendix J. Taxiway Additional Information … J-1

J.1 Purpose … J-1

J.2 Taxiway Fillet and Turn Design … J-1

J.3 TDG Tables for Common Intersection Angles … J-8

J.4 Methodology and Calculations for Reductions in TOFA/TLOFA Standards … J-13

J.5 Taxiway Geometries with Elevated Risk to Safety … J-16

Appendix K. Instrument Flight Procedures … K-1

Paragraph Page

xv

K.1 Instrument Flight Procedures (IFP) … K-1

Appendix L. Approach and Departure Reference Codes … L-1

L.1 General Overview … L-1

L.2 Approach Reference Code (APRC) … L-1

L.3 Departure Reference Code (DPRC) … L-4

Appendix M. Differences in Airport Design Standards and Relationship of Aircraft

Characteristics to Design Components … M-1

Appendix N. Acronyms … N-1

Appendix O. Index … O-1

FIGURES

Figure 1-1. Taxiway Design Groups (TDGs) … 1-15

Figure 3-1. Airport Layout Example … 3-2

Figure 3-2. Runway Ends … 3-7

Figure 3-3. Standard Approach Surface … 3-10

Figure 3-4. Displaced Threshold … 3-11

Figure 3-5. Visual Approach Surfaces … 3-12

Figure 3-6. Non-Precision and IFR Circling Approach Surfaces … 3-13

Figure 3-7. APV and PA Instrument Runway Approach Surfaces … 3-14

Figure 3-8. Offset Approach Plane … 3-15

Figure 3-9. Instrument Departure Surface … 3-18

Figure 3-10. Departure Surface with Clearway … 3-19

Figure 3-11. Departure Surface – Perspective View (Without Clearway) … 3-20

Figure 3-12. Converging Non-Intersecting Runways … 3-23

Figure 3-13. Intersecting Runways … 3-25

Figure 1-1: picture of page 15Figure 1-1 · page 15
Picture of the page from the copy saved here

Figure 3-14. Runway Visibility Zone – Perpendicular Intersection Runways … 3-26

Figure 3-15. Runway Visibility Zone – Non-Perpendicular Intersecting Runways – X Less Than

750 Feet (229 m) … 3-28

Figure 3-16. Runway Visibility Zone – Non-Perpendicular Intersecting Runways – X Distance

Equal to or Greater Than 750 Feet (229 m) … 3-28

Figure 3-17. Runway Visibility Zone for Converging Non-Intersecting Runways … 3-30

Page

xvi

Figure 3-18. Parallel Runway Separation – Simultaneous Radar-Controlled Mixed Operations

with Staggered Thresholds … 3-34

Figure 3-19. Runway Safety Area (RSA) … 3-35

Figure 3-20. Obstacle Free Zone (OFZ) for Visual Runways and Runways with Not Lower Than

¾ Statute Mile (1.2 km) Approach Visibility Minimums … 3-39

Figure 3-21. OFZ for Operations on Runways by Small Aircraft with Lower Than ¾ Statute Mile

(1.2 km) Approach Visibility Minimums … 3-40

Figure 3-22. OFZ for Operations on Runways by Large Aircraft with Lower Than ¾ Statute Mile

(1.2 km) Approach Visibility Minimums … 3-41

Figure 3-14: picture of page 15Figure 3-14 · page 15
Picture of the page from the copy saved here

Figure 3-23. OFZ for Operations on Runways by Large Aircraft with Lower Than ¾ Statute Mile

(1.2 km) Approach Visibility Minimums and Displaced Threshold … 3-42

Figure 3-24. Precision Obstacle Free Zone (POFZ) – No Displaced Threshold … 3-45

Figure 3-25. POFZ – Displaced Threshold … 3-46

Figure 3-26. Runway Protection Zone (RPZ), Runway Object Free Area (ROFA), and Runway

Safety Area (RSA) … 3-49

Figure 3-27. Runway with all Declared Distances Equal to the Runway Length … 3-50

Figure 3-28. Approach and Departure RPZs Where the Takeoff Run Available (TORA) is Less

Than the Takeoff Distance Available (TODA) … 3-51

Figure 3-29. Clearway … 3-53

Figure 3-30. Stopway … 3-54

Figure 3-31. Longitudinal Grade Limitations for Aircraft Approach Categories A and B … 3-55

Figure 3-32. Longitudinal Grade Limitations for Aircraft Approach Categories C, D, and E .. 3-56

Figure 3-33. Transverse Grade Limitations … 3-57

Figure 3-34. Alternate Runway Cross Sections … 3-59

Figure 3-35. RSA Grade Limitations Beyond 200 feet (61 m) from the Runway End … 3-63

Figure 3-23: picture of page 16Figure 3-23 · page 16
Picture of the page from the copy saved here

Figure 4-1. Three-Path Concept Taxiway Intersection … 4-4

Figure 4-2. Apron-Taxiway Transition … 4-6

Figure 4-3. Apron-Runway Transition … 4-7

Figure 4-4. Taxiway Edge Safety Margin (TESM) – Straight Segment … 4-8

Figure 4-5. Wingtip Clearance – Parallel Taxiways/Taxilanes … 4-11

Figure 4-6. Wingtip Clearance from Taxiway … 4-12

Figure 4-7. Taxilane Separations and Clearances … 4-13

Figure 4-8. Wingtip Clearance from Apron Taxilane … 4-15

Figure 4-9. TSA and TOFA at Taxiway Intersections … 4-16

Page

xvii

Figure 4-10. Parallel Taxiways … 4-18

Figure 4-11. Parallel Taxiway Offset … 4-19

Figure 4-12. Taxiway Turn – 90-Degree Delta … 4-21

Figure 4-13. Taxiway Turn – Less Than 90-Degree Delta … 4-22

Figure 4-14. Taxiway Turn – Greater Than 90-Degree Delta … 4-22

Figure 4-15. Entrance Taxiway … 4-25

Figure 4-16. Bypass Taxiway Bay Configuration … 4-27

Figure 4-17. Right-Angled Exit Taxiway … 4-28

Figure 4-18. Cumulative Probability of Aircraft Able to Exit by AAC at Airports with an

Elevation Less Than 2,000 feet (610 m) MSL … 4-29

Figure 4-19. High-Speed Exit … 4-32

Figure 4-1: picture of page 16Figure 4-1 · page 16
Picture of the page from the copy saved here

Figure 4-20. High-Speed Exit – Reverse Turn … 4-33

Figure 4-21. High-Speed Exit Separation … 4-33

Figure 4-22. Crossover Taxiway, Taxiway Separation Based on ADG … 4-34

Figure 4-23. Crossover Taxiway, Taxiway Separation Based on TDG … 4-35

Figure 4-24. Crossover Taxiway Reverse Turn, Taxiway Separation Based on ADG … 4-36

Figure 4-25. Holding Bay Configuration … 4-37

Figure 4-26. Holding Bay – Alternate Configuration … 4-38

Figure 4-27. Taxiway Turnaround … 4-39

Figure 4-28. End-Around Taxiway (EAT) … 4-41

Figure 4-29. Taxiway and Taxilane Transverse Gradients … 4-45

Figure 5-1. Types of Aprons … 5-2

Figure 5-2. Parking Position Clearance … 5-8

Figure 5-3. Passenger Terminal Gate Area … 5-22

Figure 6-1. Shoulder Markings for Taxiway Bridges … 6-4

Figure 6-2. Compass Calibration Pad … 6-18

Figure 6-3. Typical Communications, Navigation, Surveillance, and Weather (CNSW) … 6-22

Figure 6-4. Two Frangible Connections … 6-26

Figure 6-5. Remote Transmitter/Receiver (RTR) Communication Facility … 6-27

Figure 6-6. Airport Surveillance Radar (ASR) Steel Tower (17 feet (5.2 m) high) … 6-28

Figure 4-20: picture of page 17Figure 4-20 · page 17
Picture of the page from the copy saved here

Figure 6-7. Approach Lighting System (ALS) with Sequenced Flashers … 6-30

Figure 6-8. Medium Intensity Approach Lighting System with Runway Alignment Indicator

Lights (MALSR) … 6-31

Page

xviii

Figure 6-9. MALS … 6-32

Figure 6-10. MALS with Sequenced Flashers (MALSF) … 6-33

Figure 6-11. Omnidirectional Airport Lighting System (ODALS) … 6-34

Figure 6-12. Lead-in Lighting System (LDIN) … 6-35

Figure 6-13. Runway End Identifier Lighting (REIL) … 6-36

Figure 6-14. 4-Unit Precision Approach Path Indicator (PAPI) … 6-38

Figure 6-15. Instrument Landing System (ILS) Localizer (LOC) Siting and Critical Area … 6-39

Figure 6-16. LOC 8-Antenna Array … 6-40

Figure 6-17. Glide Slope (GS) Siting and Critical Area … 6-41

Figure 6-18. GS Antenna and Equipment Shelter … 6-41

Figure 6-19. Distance Measuring Equipment (DME) Antenna … 6-42

Figure 6-20. Runway Visual Range (RVR) … 6-43

Figure 6-21. Enroute VHF Omnidirectional Range (VOR) Facility … 6-44

Figure 6-22. Terminal Very High Frequency Omnidirectional Range (TVOR) Facility … 6-45

Figure 6-23. Non-Directional Beacon (NDB) Facility … 6-46

Figure 6-7: picture of page 17Figure 6-7 · page 17
Picture of the page from the copy saved here

Figure 6-24. Segmented Circle and Wind Cone … 6-47

Figure 6-25. Automated Surface Observing System (ASOS) Weather Sensors Suite … 6-47

Figure 6-26. Weather Camera (WCAM) Pole … 6-48

Figure 6-27. Weather Equipment Sensor Pole … 6-49

Figure 6-28. Low Level Windshear Alert System (LLWAS) Sensor Pole … 6-50

Figure 6-29. Automated Dependent Surveillance Broadcast (ADS-B) Ground Station … 6-51

Figure A-1. Key Dimensions – Large Aircraft … A-1

Figure A-2. Key Dimensions – Small Aircraft … A-2

Figure A-3. Folding Wingtips … A-3

Figure B-1. Wind Vector Diagram … B-4

Figure B-2. Blank Windrose Graphic Showing Direction and Divisions … B-8

Figure B-3. Completed Windrose Graphic Using Table B-2 Data … B-9

Figure B-4. Windrose Analysis … B-10

Figure D-1. End-Around Taxiway (EAT) Screen Sizing and Location … D-2

Figure D-2. Example Visual Screen Structure … D-5

Figure D-3. Example Panel Layout for 13-foot (4 m) High Screen … D-8

Figure D-4. Visual Screen Stripe Orientation … D-9

Page

xix

Figure E-1. Tiedown Layout … E-4

Figure E-2. Tiedown Spacing … E-5

Figure E-3. Nested Tiedowns … E-6

Figure 6-24: picture of page 18Figure 6-24 · page 18
Picture of the page from the copy saved here

Figure E-4. Single Path Entry/Exit Taxilane … E-8

Figure E-5. Dual Path Entry/Exit Taxilane … E-8

Figure E-6. T-Hangar Complex … E-10

Figure E-7. Standard T-Hangar Layout … E-12

Figure E-8. Nested T-Hangar Layout … E-12

Figure E-9. Separation of Vehicle Parking and Aircraft Pavement … E-16

Figure H-1. Typical Starting Point for ASDA, TODA, and TORA … H-4

Figure H-2. Modified TODA and TORA due to Object Penetration of 40:1 Surface … H-6

Figure H-3. Extended TODA with Clearway – Shortened TORA … H-7

Figure H-4. Typical Location of TODA Departure End of Runway (DER) – No Clearway .... H-8

Figure H-5. Extended TODA with Clearway – Typical TORA … H-9

Figure H-6. Typical Location of Departure End of ASDA and LDA … H-11

Figure H-7. Adjusted ASDA and LDA Departure End for the RSA … H-12

Figure H-8. Adjusted ASDA and LDA Departure End for ROFA … H-13

Figure H-9. Departure End of ASDA with Stopway … H-14

Figure H-10. Typical Start of LDA … H-16

Figure H-11. LDA Starting Point – Displaced Threshold for Approach and Departure Surfaces

… H-17

Figure H-12. LDA Starting Point – Displaced Threshold for Adjusted RPZ … H-18

Figure H-13. LDA Starting Point – Displaced Threshold for Adjusted RSA … H-19

Figure H-14. LDA Starting Point – Displaced Threshold for Adjusted ROFA … H-20

Figure I-1. Percent of Aircraft Overrun Versus Distance Beyond the Runway End … I-2

Figure I-2. Threshold Displacement on a Visual Runway … I-4

Figure I-3. Overlapping Runway Safety Areas – Elevated Risk … I-5

Figure I-4. Intersecting Runways – Elevated Risk … I-6

Figure J-1. Fillet Design Example … J-2

Figure J-2. Angle of Intersection (Delta) … J-4

Figure J-3. Steering Angle of No More Than 50 Degrees … J-4

Figure J-4. Track of the Main Gear is Modeled, Offset by the Taxiway Edge Safety Margin

(TESM) … J-5

Page

xx

Figure J-5. Minimize Excess Pavement While Providing the Standard TESM … J-5

Figure J-6. Pavement Edge (Main Gear Track + TESM) Offset by 6 inches (152 mm) … J-6

Figure J-7. Detail of Figure J-6 … J-6

Figure J-8. Taper Selection to Minimize Excess Pavement with Consideration for

Constructability … J-7

Figure J-9. Establishing Radius of Outer Taxiway Pavement Edge Based on the Centerline

Radius and Taxiway Width for Each TDG … J-7

Figure J-10. Dimensioning the Fillet Design … J-8

Figure J-11. TOFA/TLOFA Width … J-13

Figure J-12. Separation Distance between Parallel Taxiways/Taxilanes … J-15

Figure J-13. Extra-Wide Pavement Area at Runway Entrance … J-18

Figure J-14. Entrance Taxiway Intersecting Runway End at an Angle less than 90 Degrees ... J-19

Figure J-15. Entrance Taxiway Intersecting Runway End at an Angle Greater Than 90 Degrees J-

20

Figure J-16. Aerial Image of Complex Taxiway Intersection Exceeding the “Three-Path”

Concept … J-21

Figure J-17. Complex Taxiway Intersection Not Meeting the “Three-Path Concept” … J-22

Figure J-18. Taxiway Intersection that Coincides with Multiple Runways … J-23

Figure J-19. Y-Shaped Taxiway Crossing a Runway … J-24

Figure J-20. Apron-Taxiway Configuration – Elevated Risk … J-25

Figure J-21. Aerial Image of High-speed Exit Co-located with Connecting Taxiways … J-26

Figure J-22. High-Speed Exit Co-located with Connecting Taxiway … J-27

Figure J-23. Aerial Image of High-speed Exit Leading to Another Runway … J-28

Figure J-24. Parallel Taxiway Adjacent to Apron Pavement … J-29

Figure J-25. Aerial Image of Short (Stub) Taxiway Connection to a Runway … J-30

Figure J-26. Poor Holding Bay – Moderate Risk Configuration … J-31

Figure J-27. Poor Holding Bay – Elevated Risk Configuration … J-31

Figure J-28. Co-located High-Speed Runway Exit Taxiways … J-32

Figure J-29. Taxiway Fillet Pavement for Uncommon Turn … J-33

Figure J-30. Aligned Taxiway and Common Mitigations … J-34

Figure J-31. Taxiway Connections to V-shaped Runways … J-35

Figure J-32. Taxiways to Converging, Non-Intersecting Runways … J-35

Figure J-33. Parallel Taxiway/Runway Intersection – Elevated Risk … J-37

Page

xxi

Figure J-34. Parallel Taxiway/Runway Intersection – Optimum Configuration … J-38

Figure L-1. ADG V-VI Departures … L-5

TABLES

Table 1-1. Aircraft Approach Category (AAC) … 1-13

Table 1-2. Airplane Design Group (ADG) … 1-13

Table 1-3. Visibility Minimums … 1-14

Table 1-4. TDG Table … 1-15

Table 3-1. Runway Design Standards … 3-1

Table 3-2. Visual Approach Surfaces … 3-12

Table 3-3. Non-Precision and IFR Circling Approach Surfaces … 3-13

Table 3-4. APV and PA Instrument Runway Approach Surfaces … 3-14

Table 3-5. Instrument Departure Surface … 3-17

Table 3-6. Transverse Grades Based on AAC … 3-60

Table 3-7. Transverse Grades Based on ADG … 3-61

Table 4-1. Design Standards Based on Airplane Design Group (ADG) … 4-10

Table 4-2. Design Standards Based on Taxiway Design Group (TDG) … 4-10

Table 4-3. Runway to Taxiway Separation for Reverse Turns from a High-Speed Exit Based on

TDG … 4-32

Table 5-1. Parking Position Clearance … 5-7

Table 6-1. Fixed-by-Function Designation for CNSW Equipment … 6-24

Table B-1. Allowable Crosswind Component per Runway Design Code (RDC) … B-3

Table B-2. Standard Wind Analysis Results for ALL_WEATHER … B-7

Table C-1. Air Velocity Sensitivity Thresholds … C-1

Table D-1. Aircraft Characteristics … D-4

Table D-2. Notes for Figure D-2 – High Frame Elevation … D-6

Table D-3. Notes for Figure D-2 – Intermediate Frame Elevation … D-6

Table D-4. Notes for Figure D-2 – Low Frame Elevation … D-6

Table D-5. Daytime Color (x, y, Y) Specification Limits … D-9

Table D-6. Minimum Coefficient of Retroreflection Candelas/Foot Candle/Square

Foot/Candelas/Lux/Square Meter … D-9

Page

xxii

Table D-7. Visual Screen Panel Wind Loads … D-10

Table E-1. Minimum Parking Position Sizing … E-2

Table G-1. Runway Design Standards Matrix, A/B-I Small Aircraft … G-1

Table G-2. Runway Design Standards Matrix, A/B-I … G-2

Table G-3. Runway Design Standards Matrix, A/B–II Small Aircraft … G-3

Table G-4. Runway Design Standards Matrix, A/B–II … G-4

Table G-5. Runway Design Standards Matrix, A/B-III … G-5

Table G-6. Runway Design Standards Matrix, A/B-IV … G-6

Table G-7. Runway Design Standards Matrix, C/D/E-I … G-7

Table G-8. Runway Design Standards Matrix, C/D/E-II … G-8

Table G-9. Runway Design Standards Matrix, C/D/E-III … G-9

Table G-10. Runway Design Standards Matrix, C/D/E-IV … G-10

Table G-11. Runway Design Standards Matrix, C/D/E-V … G-11

Table G-12. Runway Design Standards Matrix, C/D/E-VI … G-12

Table H-1. Relation of Declared Distances to Design Standards … H-2

Table J-1. Taxiway Intersection Dimensions for TDG 1A … J-9

Table J-2. Taxiway Intersection Dimensions for TDG 1B … J-9

Table J-3. Taxiway Intersection Dimensions for TDG 2A … J-10

Table J-4. Taxiway Intersection Dimensions for TDG 2B … J-10

Table J-5. Taxiway Intersection Dimensions for TDG 3 … J-11

Table J-6. Taxiway Intersection Dimensions for TDG 4 … J-11

Table J-7. Taxiway Intersection Dimensions for TDG 5 … J-12

Table J-8. Taxiway Intersection Dimensions for TDG 6 … J-12

Table J-9. TOFA Calculations (feet) … J-14

Table J-10. TLOFA Calculations (feet) … J-14

Table K-1. Criteria to Support Instrument Flight Procedure Development … K-4

Table L-1. Approach Reference Code (APRC) … L-2

Table L-2. Departure Reference Code (DPRC) … L-4

Page

xxiii

Table M-1. Differences in Design Standards with Upgrade in Aircraft Approach Category

(AAC) and Airplane Design Group (ADG) … M-1

Table M-2. Differences in Airport Design Standards with Lowering Approach Visibility

Minimums … M-3

Table M-3. Relationship of Aircraft Characteristics to Design Components … M-4

xxiv

Page Intentionally Blank

Chapter 1. Introduction › 1.2 Standards, Recommended Practices, and Requirements.

CHAPTER 1. Introduction

1.1 Policy. The Federal Aviation Administration (FAA) has statutory authority to serve the public interest by developing a national aviation system for air commerce. Congress established it is within the public interest to assign, maintain, and enhance safety and security as the highest priorities in air commerce. See Title 49 United States Code (U.S.C.) § 40101(d)(1).

1.1.1 Airport Development. It is the policy of the United States that the safe operation of the airport and airway system is the highest aviation priority. See 49 U.S.C. § 47101(a)(1). Among other responsibilities, the FAA’s mission includes the development of airports to serve passengers and cargo in an efficient and effective manner that protects and enhances the natural resources and the quality of the environment of the United States. See 49 U.S.C. § 47101(a)(6).

1.2 Standards, Recommended Practices, and Requirements. The promulgation of the standards and recommendations contained in this Advisory Circular (AC) advance the goals and objectives of the FAA’s statutory authorities and the national policies established by Congress.

1.2.1 Meaning of Terms.

Standard. A physical characteristic, quality, configuration, function, operation, or procedure established by the FAA as a benchmark for uniformity, safety, capacity, performance, economy, and environmental quality. The FAA’s standards serve a prominent role in fulfilling the statutory objectives summarized in paragraph 1.1.1.

Recommended Practice. Supplemental measures and guidelines the FAA recognizes as promoting safety, capacity, or efficiency. An airport has the discretion to implement a recommended practice to address a site-specific condition.

Requirement. Mandatory language such as “must,” “shall,” “required,” or “requirements,” used in this AC describes obligations that originate in either Federal statutes or regulations. This AC does not establish or modify any statutory or regulatory requirements; it provides information regarding existing requirements under the law or agency policies.

Chapter 1. Introduction › 1.3 Federal Regulations.

Design Consideration. Additional factors to take into account during airport design that may influence application of a standard or recommended practice.

1.2.2 Application of Airport Design Standards. The standards and recommendations in this AC cover a wide range of size and performance characteristics of aircraft planned to operate at an airport. Airport development conforming to the standards of this AC establish an acceptable level of safety that ensures optimum operation of the critical aircraft (see paragraph 2.6.1) independent of individual operational controls that may affect the utility and efficiency of airport operations.

1.2.3 Operations Exceeding Airport Standards. This AC does not prevent, regulate, or control the operation of aircraft at airports where the physical characteristics of the runways, taxiways, and aprons do not meet the standards provided herein for operation of a more demanding aircraft. While an aircraft operation exceeding airport standards is not inherently unsafe, such operations have the potential to introduce hazards and risks to the pilot or aircraft operator as well as to other aircraft, vehicles, individuals, and facilities on the airport.

Specific operational controls may be necessary in order to establish an acceptable level of safety for the operation of aircraft that exceed the standards at the airport. Consult with the appropriate FAA office (e.g., Airports, Flight Standards, Air Traffic Organization (ATO)) to identify potential adjustments to operational procedures that can accommodate these operations. Refer to AC 150/5000-17, Critical Aircraft and Regular Use Determination, for guidance related to critical aircraft.

1.3 Federal Regulations. The following Federal regulations govern airport development. This list is not exhaustive.

1.3.1 14 CFR Part 77, Safe, Efficient Use and Preservation of the Navigable Airspace.

14 CFR Part 77 requires proponents of construction or alteration on or near an airport to give the FAA timely notification. This notification serves as the FAA’s basis for evaluating the effect of the proposed construction or alteration on safety, air navigation, and airport traffic capacity at public use airports. The evaluation determines the level of obstruction marking and lighting and if additional measures are necessary for continued safety of air navigation.

The FAA Obstruction Evaluation/Airport Airspace Analysis (OE/AAA) website https://oeaaa.faa.gov/oeaaa is available for electronic submission of this notice. FAA Order JO 7400.2, Procedures for Handling Airspace Matters, establishes the FAA’s policy for processing airspace matters.

Chapter 1. Introduction › 1.5 Definitions.

1.3.2 14 CFR Part 139, Certification of Airports. Part 139 regulates airports, including joint-use airports, having scheduled air carrier operations with more than nine passenger seats or unscheduled air carrier operations with more than 30 passenger seats. This AC, along with other applicable ACs, contains methods and procedures that certificate holders may use to comply with Part 139 requirements.

1.3.3 14 CFR Part 157, Notice of Construction, Alteration, Activation and Deactivation of Airports. Part 157 establishes standards and notification requirements for persons proposing to construct, alter, or deactivate a civil or joint-use (civil/military) airport. This regulation also addresses proposals that alter the status or use of an airport. This notification serves as the FAA’s basis for evaluating the effects of the proposed action on the safe and efficient use of airspace by aircraft and the safety of persons and property on the ground. Notification allows the FAA to identify potential aeronautical hazards in advance, thus preventing or minimizing adverse impacts to the safe and efficient use of navigable airspace.

1.3.4 49 CFR Part 1542, Airport Security. Part 1542 is a Transportation Security Administration regulation governing the security of airports that serve air carriers operating under security programs, per 49 CFR Part 1544, Aircraft Operator Security: Air Carriers and Commercial Operators, or 49 CFR Part 1546, Foreign Air Carrier Security. Compliance with Part 1542 satisfies the public protection requirements of § 139.335, Public Protection, from Part 139.

1.4 Environmental Protection. The National Environmental Policy Act (NEPA) requires Federal agencies to consider the environmental effects of major Federal actions and their reasonable alternatives. Federal assistance for airport development projects and airport layout plan (ALP) approvals, where required by statute, are Federal actions that require the FAA to follow the procedures of NEPA. FAA compliance with NEPA is a legal requirement and aligns with the national policy of protecting and enhancing natural resources and the quality of the environment of the United States. For additional guidance and information, refer to the following FAA documents:

1. FAA Order 1050.1, Environmental Impacts: Policies and Procedures.

2. FAA Order 5050.4, National Environmental Policy Act (NEPA) Implementing Instructions for Airport Actions.

The circumstances in which the FAA must approve ALPs are addressed in 49 U.S.C. § 47101(a)(16).

1.5 Definitions.

1. Accelerate-Stop Distance Available (ASDA). See Declared Distances.

2. Aeronautical Study. Process by which the FAA determines the impact of an object on the safe and efficient use of airspace (see 14 CFR Part 77), or the impact of an airport proposal (see 14 CFR Part 157).

3. Air Operations Area (AOA).

a. For 14 CFR Part 139 certificated airports, the air operations area is that portion of an airport in which security measures of 49 CFR Part 1540, Civil Aviation Security: General Rules, apply. This area includes aircraft movement areas, aircraft parking areas, loading ramps, and safety areas, for use by aircraft regulated under 49 CFR Part 1544, or 49 CFR Part 1546, and any adjacent areas (such as general aviation (GA) areas) that are not separated by adequate security systems, measures, or procedures (see 49 CFR § 1540.5).

b. For non-Part 139 airports (e.g., GA airports), the air operations area is the

paved and unpaved areas of an airport intended to facilitate aeronautical operations where local security measures apply. Typically, the air operations area encompasses that part of the airport within the perimeter fence.

4. Air Traffic Control Facilities (ATC-F). Electronic equipment and buildings aiding air traffic control (ATC) for communications and surveillance of aircraft including weather detection and advisory systems.

5. Aircraft. For this AC, the terms “aircraft” and “airplane” are synonymous, referring to all types of fixed-wing airplanes, including gliders. Unless specifically noted, these two terms exclude powered lift (tiltrotors) and single and dual rotor helicopters.

6. Aircraft Approach Category (AAC). As specified in 14 CFR § 97.3, Symbols and Terms Used in Procedures, a grouping of aircraft based on a reference landing speed (VREF), if specified, or if VREF is not specified, 1.3 times stall speed (VSO) at the maximum certificated landing weight. VREF, VSO, and the maximum certificated landing weight are those values established for the aircraft by the certification authority of the country of registry. See Table 1-1.

7. Airplane. A fixed-wing aircraft that is heavier than air and supported by the dynamic reaction of the air against its wings (see Aircraft).

8. Airplane Design Group (ADG). A classification of aircraft based on wingspan and tail height. When the aircraft wingspan and tail height fall in different groups, the larger group applies. See Table 1-2.

9. Airport Elevation. The highest point on an airport’s usable runways expressed in feet above mean sea level (MSL).

10. Airport Layout Plan (ALP). A scaled drawing or set of drawings, in either hardcopy or electronic form, of existing and future airport facilities that provides a graphic representation of the existing and long-term development plan for the airport and demonstrates the preservation and continuity of safety, utility, and efficiency of the airport to the FAA’s satisfaction.

11. Airport Reference Point (ARP). The approximate geometric center of all usable runways at the airport.

12. Airport. An airport means an area used or intended to be used for the takeoff or landing of aircraft (14 CFR § 1.1).

13. Aligned Taxiway. A non-standard taxiway configuration with the centerline aligned with a runway centerline. Sometimes referred to as an “inline taxiway.” Aligned taxiways represent a runway/taxiway configuration that increases the risk of a runway incursion.

14. Approach Procedures with Vertical Guidance (APV). An instrument approach based on a navigation system that provides course and glidepath deviation information but does not meet the precision approach standards of International Civil Aviation Organization (ICAO) Annex 10.

15. Approach Reference Code (APRC). A code signifying the current operational capabilities, within current standards, of a runway and associated parallel taxiway with regards to landing operations. See Appendix L.

16. Approach Surface Baseline. A horizontal line tangent to the surface of the earth at the runway threshold aligned with the final approach course.

17. Blast Fence. A barrier used to divert or dissipate jet blast or propeller wash.

18. Blast Pad. A surface adjacent to the ends of runways provided to reduce the erosive effect of jet blast and propeller wash.

19. Building Restriction Line (BRL). For planning considerations, a line identifying suitable and unsuitable locations for buildings on the airport.

20. Bypass Taxiway. An entrance taxiway used to manage aircraft queuing demand by providing multiple runway access points at or near a runway end or threshold.

21. Category-I (CAT-I). An instrument approach, or approach and landing, with a height above touchdown (HAT) or minimum descent altitude not lower than 200 ft (61 m) and with either a visibility not less than ½ statute mile (0.8 km), or a runway visual range not less than 1800 ft (549 m).

22. Category-II (CAT-II). An instrument approach, or approach and landing, with a HAT lower than 200 ft (61 m) but not lower than 100 ft (30.5 m) and a runway visual range not less than 1200 ft (366 m).

23. Category-III (CAT-III). An instrument approach, or approach and landing, with a HAT lower than 100 ft (30.5 m), or no HAT, or a runway visual range less than 1200 ft (366 m).

24. Circling Approach. A maneuver initiated by the pilot to align the aircraft with a runway for landing when a straight-in landing from an instrument approach is not possible or desirable.

25. Clearway. A defined rectangular area beyond the end of a runway cleared or suitable for use in lieu of a runway to satisfy takeoff distance requirements (see also Takeoff Distance Available (TODA)).

26. Cockpit to Main Gear Distance (CMG). The distance from the pilot’s eye to the main gear turn center.

27. Commercial Service Airport. A public use airport receiving scheduled passenger aircraft service and at least 2,500 annual passenger boardings. Refer to the definition of Title 49 U.S.C. § 47102, Definitions.

28. Compass Calibration Pad. An airport facility used for calibrating an aircraft compass.

29. Critical Aircraft. The critical aircraft is the most demanding aircraft type, or grouping of aircraft with similar physical and operational characteristics, that makes regular use of an airport. Regular use is 500 annual operations, excluding touch-and-go operations. See AC 150/5000-17. The critical aircraft determines the applicable design standards for facilities on the airport including individual runways, taxiways, etc. Previously referred to as “design aircraft.”

30. Crossover Taxiway. A taxiway connecting two parallel taxiways (also referred to as a “transverse taxiway”).

31. Decision Altitude (DA). A specified altitude on a vertically-guided approach at which a pilot initiates a missed approach if the pilot cannot establish the required visual reference to continue the approach. Values for DA reference MSL as the datum.

32. Declared Distances. The distances declared available for an aircraft’s takeoff run, takeoff distance, accelerate-stop distance, and landing distance requirements. The distances are:

a. Takeoff Run Available (TORA) – the runway length declared available and suitable for the ground run of an aircraft taking off;

b. Takeoff Distance Available (TODA) – the TORA plus the length of any

remaining runway or clearway beyond the far end of the TORA; the full length of TODA may need to be reduced because of obstacles in the departure area;

c. Accelerate-Stop Distance Available (ASDA) – the runway plus stopway length declared available and suitable for the acceleration and deceleration of an aircraft aborting a takeoff; and

d. Landing Distance Available (LDA) – the runway length declared available and

suitable for landing an aircraft.

33. Departure End of Runway (DER). The end of the runway that is opposite the landing threshold.

34. Departure Reference Code (DPRC). A code signifying the current operational capabilities, within current standards, of a runway with regard to takeoff operations. See Appendix K.

35. Displaced Threshold. A threshold that is located at a point on the runway beyond the beginning of the runway. See Threshold.

36. End-Around Taxiway (EAT). A taxiway crossing the extended centerline of a runway and designed for free flow without specific clearance from ATC.

37. Entrance Taxiway. A taxiway designed for use by an aircraft for direct entry to a runway. An entrance taxiway may also serve as an exit from the runway.

38. Exit Taxiway. A taxiway designed for aircraft exit-only from a runway:

a. Acute-Angled Exit Taxiway – A taxiway forming an angle less than 90 degrees from the runway centerline.

b. High Speed Exit Taxiway – Also known as rapid exit taxiway, an acute-angled

exit taxiway forming a 30-degree angle with the runway centerline, designed to allow aircraft to exit a runway quickly without having to decelerate to typical taxi speed.

39. Fixed-By-Function Navigational Aid (NAVAID). An air navigational aid positioned in a specific location in order to provide an essential benefit for aviation is fixedby-function. Table 6-1 gives fixed-by-function designations for various NAVAIDs as they relate to the Runway Safety Area (RSA) and Runway Object Free Area (ROFA).

40. Frangible. A physical characteristic whereby an object retains its structural integrity and stiffness up to a designated maximum load, but upon impact from a greater load, breaks, distorts, or yields in such a manner as to present the minimum hazard to aircraft. See AC 150/5220-23, Frangible Connections.

41. General Aviation (GA). Per the Pilot/Controller Glossary, that portion of civil aviation that does not include scheduled or unscheduled air carriers or commercial space operations.

42. General Aviation (GA) Airport. A public-use airport that: 1) does not have scheduled service, or 2) has scheduled service with less than 2,500 annual passenger boardings. See 49 U.S.C. § 47102. FAA Report, General Aviation Airports: A National Asset – May 2012, establishes the following classifications of general aviation airports: national, regional, local, and basic.

43. Glidepath Angle (GPA). The GPA is the angle of the final approach descent path relative to the approach surface baseline.

44. Glide Slope (GS). Equipment in an Instrument Landing System (ILS) that provides electronic vertical guidance to landing aircraft.

45. Hazard to Air Navigation. An existing or proposed object that the FAA, as a result of an aeronautical study, determines will have a substantial adverse effect upon the safe and efficient use of navigable airspace by aircraft, operation of air navigation facilities, or existing or potential airport capacity.

46. Height Above Airport (HAA). The height of the circling approach minimum descent altitude (MDA) above the airport elevation.

47. Height Above Touchdown (HAT). The height of the Decision Height or MDA above the highest runway elevation in the touchdown zone (first 3,000 feet (914 m) of the runway). Instrument approach charts publish the HAT in conjunction with all straight-in minimums.

48. High-energy area/intersection. An area or intersection within the middle third of a runway.

49. Hot Spot. A location on an airport movement area with a history of potential risk of a collision or runway incursion. Heightened attention by pilots/drivers/controllers is necessary when maneuvering through a hot spot.

50. International Civil Aviation Organization (ICAO). ICAO is a United Nations specialized agency that manages the administration and governance of the Convention on International Civil Aviation. ICAO works with its Member States and industry groups to reach consensus on international civil aviation standards, recommended practices, and policies in support of a safe, efficient, secure, economically sustainable, and environmentally responsible civil aviation sector.

51. Instrument Departure Runway. A runway identified by the airport operator, through the appropriate FAA Airports Office, to the FAA Regional Airspace Procedures Team intended primarily for instrument departures.

52. Instrument Flight Procedure (IFP). An instrument flight procedure is a series of predetermined maneuvers for aircraft operating under instrument flight rules, e.g., instrument flight rules (IFR) conditions, when visual flight is not possible due to weather or other visually restrictive conditions. These maneuvers allow for the orderly transition of the aircraft through a particular airspace. The term “instrument flight procedure” refers to instrument approaches, instrument departures, and instrument en route operations.

53. Island. A non-serviceable paved or grassy area bounded by a taxiway, taxilane, or apron pavement.

54. Joint-Use Airport. An airport owned by the Department of Defense (DoD) at which both military and civilian aircraft make shared use of the airfield. Refer to 14 CFR Part 139.

55. Landing Distance Available (LDA). See Declared Distances.

56. Large Aircraft. An aircraft with a maximum certificated takeoff weight of more than 12,500 lbs (5,669 kg).

57. Low Impact Resistant (LIR) Support. A support designed to resist operational and environmental static loads and fail when subjected to a shock load such as that from a colliding aircraft.

58. Main Gear Width (MGW). The distance from outer edge to outer edge of the widest set of main gear tires.

59. Minimum Descent Altitude (MDA). The lowest altitude, expressed in feet above MSL, to which descent is authorized on final approach or during circle-to-land maneuvering in execution of a standard IFP where no electronic glide slope is provided.

60. Modification of Standards. Any approved deviation from published FAA standards applicable to an airport design, construction, or equipment project that is necessary to accommodate an unusual local condition for a specific project while maintaining

an acceptable level of safety and performance. FAA Order 5300.1 establishes FAA policy for administering requests for modification of standards.

61. Movement Area. An area at a towered airport designated by the Airport Traffic Control Tower (ATCT) for positive control of aircraft, vehicles, and personnel. The movement area consists of runways, taxiways, and other select areas of an airport (e.g., taxilanes) used for taxiing, takeoff, and landing of aircraft, exclusive of loading ramps and aircraft parking areas. A movement area can include area for the operation of helicopters and tiltrotors. See 14 CFR Part 139.

62. Navigational Aid (NAVAID). Electronic and visual air navigational aids, lights, signs, and associated supporting equipment.

63. Non-movement area. The areas of an airport that are used for taxiing, hover taxiing, or air taxiing aircraft including helicopters and tiltrotors, but are not part of the movement area (e.g., the loading aprons and aircraft parking areas).

64. Non-Precision Approach (NPA). An instrument approach based on a navigation system that provides course deviation information, but no glidepath deviation information.

65. Non-Precision Runway. A runway other than a precision runway with at least one end having a non-precision approach procedure.

66. Object. Includes, but is not limited to, above-ground structures, NAVAIDs, equipment, vehicles, natural growth, terrain, and parked or taxiing aircraft.

67. Object Free Area (OFA). An area centered on the surface of a runway, taxiway, or taxilane centerline provided to enhance the safety of aircraft operations by remaining clear of objects, except for objects that need to be located in the OFA for air navigation or aircraft ground maneuvering purposes.

68. Obstacle. An existing object at a fixed geographical location or a planned object at a fixed location within a prescribed area with reference to which vertical clearance is necessary during flight operation.

69. Obstacle Free Zone (OFZ). The OFZ is the three-dimensional airspace along the runway and extended runway centerline that is clear of obstacles for the protection of aircraft landing or taking off from the runway and for missed approaches. The OFZ consists of four distinct surfaces: Runway OFZ, Precision OFZ, Inner- Transitional OFZ, and the Inner-Approach OFZ.

70. Obstruction to Air Navigation. An object of greater height than any of the heights or surfaces presented in Subpart C of Title 14 CFR Part 77, Standards for Determining Obstructions to Air Navigation or Navigational Aids or Facilities.

71. Offset approach. An approach conducted at an angle offset from the runway centerline. A typical offset approach is 3 degrees to the right or left of the straight in runway heading.

72. Parallel Taxiway. A continuous taxiway path located laterally to the runway it serves, providing access to one or both runway ends without entering the runway

safety area (RSA) or runway OFZ; it is not necessary for all points along the centerline of a parallel taxiway to be equidistant from the runway centerline.

a. Dual Parallel Taxiways – Two side-by-side taxiways, parallel to each other and the runway (usually called inner parallel and outer parallel taxiway relative to the runway being served).

b. Full Parallel Taxiway – A parallel taxiway extending the full length of the

runway to provide access to both runway ends.

c. Partial Parallel Taxiway – A parallel taxiway extending less than the full length of the runway to provide access to only one runway end.

73. Plans-on-File. Plans-on-file represent the airport’s future airfield development including, but not limited to, runway extensions or construction of taxiways. Obligated airports submit their plans-on-file to the FAA by way of their ALP or submit through FAA Form 7460-1, Notice of Proposed Construction or Alteration; whereas non-obligated airports submit through FAA Form 7480-1, Notice for Construction, Alteration and Deactivation of Airports, in accordance with 14 CFR Part 157.

74. Precision Approach (PA). An instrument approach based on a navigation system that provides course and glidepath deviation information meeting the precision standards of ICAO Annex 10.

75. Precision Runway. A runway with at least one end having a precision approach procedure.

76. Primary Airport (large hub, medium hub, small hub, non-hub). A commercial service airport with 10,000 annual passenger boardings. See 49 U.S.C. § 47102.

77. Public Use Airport. An airport used for public purposes that is 1) under control of or owned by a public agency, or 2) under private ownership that is a reliever airport or has scheduled passenger service with at least 2,500 annual passenger boardings. See 49 U.S.C. § 47102.

78. Regular Use. As defined in AC 150/5000-17, regular use is 500 annual operations, including both itinerant and local operations, but excluding touch-and-go operations. An operation is either a takeoff or landing.

79. Runway (RW). A defined rectangular surface on an airport prepared or suitable for the landing or takeoff of aircraft.

80. Runway Design Code (RDC). A code signifying the design standards that apply to an existing or planned runway.

81. Runway Incursion. Any occurrence at an airport involving the incorrect presence of an aircraft, vehicle, or person on the protected area of a surface designated for the landing and takeoff of aircraft.

82. Runway Protection Zone (RPZ). An area at ground level prior to the threshold or beyond the runway end to enhance the safety and protection of people and property on the ground.

83. Runway Safety Area (RSA). A defined area surrounding the runway consisting of a prepared surface suitable for reducing the risk of damage to aircraft in the event of an undershoot, overshoot, or excursion from the runway.

84. Runway Visual Range (RVR). An instrumentally derived value that represents the horizontal visual range a pilot sees down the runway from the approach end. It is based on the sighting of either HIRL or on the visual contrast of other targets, whichever yields the greater visual range. RVR, in contrast to prevailing or runway visibility, is based on what a pilot in a moving aircraft should see looking down the runway.

85. Shoulder. An area adjacent to the defined edge of paved runways, taxiways, or aprons designed to:

a. transition between the pavement and the adjacent surface,

b. support aircraft and emergency vehicles deviating from the full-strength

pavement,

c. facilitate drainage, and

d. provide blast protection.

86. Small Aircraft. For the purpose of this AC, an aircraft with a maximum certificated takeoff weight of 12,500 lbs (5669 kg) or less (14 CFR § 1.1).

87. Stopway. An area beyond the takeoff runway, no less wide than the runway and centered upon the extended centerline of the runway, able to support the airplane during an aborted takeoff, without causing structural damage to the airplane, and designated by the airport for use in decelerating the airplane during an aborted takeoff.

88. Takeoff Distance Available (TODA). See Declared Distances.

89. Takeoff Run Available (TORA). See Declared Distances.

90. Taxilane (TL). A defined taxi path designed for low speed and precise maneuvering of aircraft. Taxilanes provide access from a taxiway to aircraft parking positions and other terminal areas. Taxi speeds on taxilanes are generally not more than 15 mph (13 kts).

91. Taxiway (TW). A defined path established for the taxiing of aircraft from one part of an airport to another. Taxi speeds on taxiways will typically range from 15 mph (13 kts) to 35 mph (30 kts).

92. Taxiway Centerline. A surface painted marking on the taxiway that provides continuous visual reference for pilot steering of aircraft during taxi operations. On straight taxiway sections, the taxiway centerline represents the physical center of the taxiway width. On curved taxiway sections, the taxiway centerline represents the optimum steering path even though the marking itself may not be located at the physical center of the pavement section.

93. Taxiway Design Group (TDG). A classification of airplanes based on outer-toouter MGW and CMG distance.

Chapter 1. Introduction › 1.6 Categories and Codes.

8/16/2024 AC 150/5300-13B Chg 1

94. Taxiway Edge Safety Margin (TESM). The distance between the outer edge of the landing gear of an airplane with its nose gear on the taxiway centerline and the edge of the taxiway pavement.

95. Taxiway Object Free Area (TOFA). See paragraph 67.

96. Taxiway/Taxilane Safety Area (TSA). A defined surface on both sides of the taxiway prepared and suitable for reducing the risk of damage to aircraft deviating from the pavement and for supporting passage of aircraft rescue and fire fighting (ARFF) equipment.

97. Threshold (TH). The beginning of that portion of the runway available for landing. A displaced threshold is located along the runway apart from the physical end of the runway. “Threshold” always refers to landing, not the start of takeoff.

98. Threshold Crossing Height (TCH). The height of the glidepath above the threshold of the runway, measured in feet.

99. Touchdown Zone (TDZ). The first 3,000 feet (914 m) of the runway beginning at the threshold. The area is used for determination of the Touchdown Zone Elevation in the development of straight-in landing minimums for instrument approaches.

100. V1. The maximum speed during takeoff at which the pilot must take the first action (e.g., apply brakes, reduce thrust, deploy speed brakes) to stop the airplane within the accelerate-stop distance. V1 also means the minimum speed during takeoff, following a failure of the critical engine at Velocity Engine Failure (VEF), at which the pilot can continue the takeoff and achieve the required height above the takeoff surface within the takeoff distance. See 14 CFR Part 1, Definitions and Abbreviations.

101. Visibility Minimums. The ability, as determined by atmospheric conditions and expressed in units of distance, to see and identify prominent unlighted objects by day and prominent lighted objects by night. Visibility reports are in units of statute miles or hundreds of feet.

102. Visual Runway. A runway without an instrument approach or departure procedure. For the purpose of this AC, consider runways with circling-only approaches as visual runways.

103. Wingspan. The maximum horizontal distance from one wingtip to the other wingtip, including the horizontal component of any extensions such as winglets or raked wingtips. See Appendix A.

1.6 Categories and Codes.

1.6.1 Aircraft Approach Categories (AAC). A grouping of aircraft related to aircraft approach speed (operational characteristic), per Table 1-1. Operational Specifications and/or Flight Standardization Board Reports applicable to specific operators and aircraft types may specify the AAC per 14 CFR §

97.3, which applies for airport design purposes in this AC. Such operators and aircraft types fall under:

• 14 CFR Part 121, Operating Requirements: Domestic, Flag, and Supplemental Operations, • 14 CFR Part 129, Operations: Foreign Air Carriers and Foreign Operators of U.S.- Registered Aircraft Engaged in Common Carriage, or • 14 CFR Part 135, Operating Requirements: Commuter and On Demand Operations and Rules Governing Persons On Board Such Aircraft

Table 1-1. Aircraft Approach Category (AAC)

AAC VREF/Approach Speed

A Approach speed less than 91 knots

B Approach speed 91 knots or more but less than 121 knots

C Approach speed 121 knots or more but less than 141 knots

D Approach speed 141 knots or more but less than 166 knots

E Approach speed 166 knots or more

1.6.2 Airplane Design Group (ADG). A grouping of aircraft related to aircraft wingspan or tail height (physical characteristics), whichever is most restrictive. Refer to Table 1-2.

Table 1-2. Airplane Design Group (ADG)

Group # Tail Height Wingspan

I < 20 ft (< 6.1 m) < 49 ft (< 14.9 m)

II 20 ft to < 30 ft (6.1 m to < 9.1 m) 49 ft to < 79 ft (14.9 m to < 24.1 m)

III 30 ft to < 45 ft (9.1 m to < 13.7 m) 79 ft to < 118 ft (24.1 m to < 36.0 m)

IV 45 ft to < 60 ft (13.7 m to < 18.3 m) 118 ft to < 171 ft (36.0 m to < 52.1 m)

V 60 ft to < 66 ft (18.3 m to < 20.1 m) 171 ft to < 214 ft (52.1 m to < 65.2 m)

VI 66 ft to < 80 ft (20.1 m to < 24.4 m) 214 ft to < 262 ft (65.2 m to < 79.9 m)

1.6.3 Visibility Minimums. The runway’s lowest visibility published on an instrument approach chart expressed by RVR values of 1,200 ft (366 m), 1,600 ft (488 m), 2,400 ft (732 m), 4,000 ft (1,219 m),

and 5,000 ft (1,524 m), per Table 1-3. For a visual approach only runway, use “VIS” in lieu of an RVR value.

Table 1-3. Visibility Minimums

RVR * Instrument Flight Visibility Category (statute mile)

5,000 ft (1,524 m) Not lower than 1 mile (1.6 km)

4,000 ft (1,219 m) Lower than 1 mile (1.6 km) but not lower than ¾ mile (1.2 km)

2,400 ft (732 m) Lower than ¾ mile (1.2 km) but not lower than ½ mile (0.8 km)

1,600 ft (488 m) Lower than ½ mile (0.8 km) but not lower than ¼ mile (0.4 km)

1,200 ft (366 m) Lower than ¼ mile (0.4 km)

* RVR values are not exact equivalents.

1.6.4 Runway Design Code (RDC). The RDC is a three-component code relating AAC, ADG, and approach visibility minimums establishing the design characteristics for a particular runway. The critical aircraft with regular use defines the AAC and ADG components of the RDC, whereas the runway’s lowest visibility published on an instrument approach chart determines the visibility component. The RDC convention is as follows:

RDC: AAC-ADG-RVR

Example: D-IV-1200

Application. The RDC establishes the standards that apply to a specific runway, existing or future. This can vary per runway. For example, an airport’s air carrier runway may have an RDC of C-IV-1200. The same airport’s GA runway may have an RDC of B-II-2400. The airport’s ALP may show both an existing RDC and future RDC.

1.6.5 Taxiway Design Group (TDG). A TDG is the grouping of aircraft based on undercarriage dimensions. TDG relates the cockpit to main gear dimension and the width of the main gear. The TDG is a primary design factor for taxiway/taxilane width and fillet standards. Separate areas of an airport may have different TDG classifications due to segregation of aircraft types, sizes, and operations. See Figure 1-1 and Table 1-4 for general reference. Tail wheel aircraft maneuver differently than aircraft with tradition tricycle landing gear. This AC does not cover designs based on tail wheel aircraft.

Chapter 1. Introduction › 1.7 Airport Layout Plan (ALP).

8/16/2024 AC 150/5300-13B Chg 1

Figure 1-1. Taxiway Design Groups (TDGs)

Values for CMG and MGW in the graph are rounded to the nearest foot. 1 foot = 0.305 meters.

Table 1-4. TDG Table

TDG (feet)

1A 1B 2A 2B 3 4 5 6

CMG 0 to ≤ 20 > 20 to

≤ 40 0 to ≤ 40 > 40 to

≤ 65 0 to ≤ 65 > 65 to

≤ 100

0 to ≤ 100

> 100 to

≤ 125

MGW 0 to ≤ 15 0 to ≤ 15 > 15 to ≤

20 0 to ≤ 20 > 20 to

≤ 30 0 to ≤ 30 > 30 to

≤ 47 0 to ≤ 47

Values in the table are rounded to the nearest foot. 1 foot = 0.305 meters.

1.7 Airport Layout Plan (ALP). An ALP is a graphic representation of existing facilities and proposed development plans for an airport. Airports that receive certain types of Federal assistance accept a grant assurance that obligates them to maintain a current ALP. See paragraph 1.9.1 for additional information on Federal obligations. Refer to the FAA’s Office of Airport Planning and Environmental (APP-400) guidance for additional information on developing ALPs.

0

20

40

60

80

100

120

140

0 5 10 15 20 25 30 35 40 45 50

CMG (feet)

MGW (feet)

TDG-6

TDG-5

TDG

-2A

TDG-1A

TDG-4

TDG-1B

TDG-2B

TDG-3

Chapter 1. Introduction › 1.8 Airport Data.

1.8 Airport Data. Airport planning, design, and evaluation activities involve collection of information that accurately describes the location, characteristics, and condition of airport facilities, infrastructure, and off-airport structures. This information also consists of geospatial data collected during the planning, design, and construction phase of airport development. It is paramount for airport operators to accurately collect and report safety-critical data to the FAA in a timely manner. Refer to AC 150/5300-18, General Guidance and Specifications for Submission of Aeronautical Surveys to NGS: Field Data Collection and Geographic Information System (GIS) Standards, for calculation requirements and further guidance.

1.8.1 Airport Reference Point (ARP). The approximate geometric center of all usable runways. The ARP is not typically monumented on the airport.

1.8.2 Aeronautical Studies. The FAA conducts aeronautical studies of proposed development on and adjacent to airports under 14 CFR Part 77, as described in paragraph 1.1. These studies assess the potential impact proposed development has on air navigation based on the best available data and plans on file. Physical changes to airport elements can adversely affect the accuracy of such studies. The FAA encourages airport operators to submit airfield changes to the FAA as soon as an airport plans changes. This includes timely submittal of ALP updates ensuring the FAA has the latest data on actual and planned facilities for the following elements:

1. Runway ends

2. Displaced thresholds

3. High and low points on the runway surfaces

4. Helipads

1.8.3 Airport Master Record. The Airport Master Record, also known as FAA Form 5010 (see https://adip.faa.gov), describes the basic operational and services data of an airport. The primary purpose of the Airport Master Record is to identify the minimum data and information about the existing physical infrastructure, characteristics, services, operations, and status of all airports composing the National Airspace System (NAS). Title 49 U.S.C. § 47130, Airport Safety Data Collection, authorizes the FAA to collect and manage this data.

The FAA uses this data for flight information publications, navigation databases, and various analyses. Airport operators, FAA inspectors, and state-sponsored inspectors may collect and submit data for the Master Record.

Timely collection and submittal of data reflecting changed conditions enhances the accuracy of aeronautical information. Refer to AC 150/5300-19, Airport Data and Information Program, for additional guidance and information.

1.8.4 Aeronautical Surveys. The FAA uses aeronautical survey data for designing and evaluating an IFP. The FAA reviews all IFPs periodically – approximately every two years. The FAA uses this data, in part, to:

1. Protect existing runway approaches from proposed development and discover obstacles that could create a hazard to air navigation by:

a. Raising approach minima,

b. Restricting night operations, or

c. Cancelling approach procedures.

2. Provide for the design and development of new IFPs to the lowest visibility minimums possible,

3. Provide accurate information for planning studies that assess the impact of airport noise, and

4. Ensure that review and coordination of on-airport development proposals maintain critical clearance standards for the completed project.

Applicable ACs.

1. AC 150/5300-16, General Guidance and Specifications for Aeronautical Surveys: Establishment of Geodetic Control and Submission to the National Geodetic Survey.

2. AC 150/5300-17, Standards for Using Remote Sensing Technologies in Airport Surveys.

3. AC 150/5300-18, General Guidance and Specifications for Submission of Aeronautical Surveys to NGS: Field Data Collection and Geographic Information System (GIS) Standards.

1.8.5 Plans-on-File. The information on file with the FAA influences the determination resulting from aeronautical studies. Having an up-to-date plan-on-file with the FAA ensures proposed airport development receives full consideration during FAA studies. An update to the ALP is the conventional method to transmit development information. Filing notification of proposed development represents another method of establishing a planon-file. Keeping plan-on-file data and information current, complete, and accurate greatly improves the effectiveness of FAA evaluations. For any new runway, runway extension, or planned runway upgrade, at a minimum the plan data includes:

1. Planned runway end and threshold coordinates and elevation

Chapter 1. Introduction › 1.10 State Role.

2. Proposed type of instrument approach

3. Desired visibility minimum(s)

4. Indication of whether the airport will have a designated instrument departure runway.

1.9 Airport Improvement Program (AIP). Title 49 U.S.C. § 47104, Project Grant Authority, authorizes the FAA to administer a grant program that provides financial assistance to public use airports for airport planning and development. Refer to paragraph 3 for applicability of the standards of this AC to projects funded by the Airport Improvement Program or other applicable grant programs. Refer to FAA Order 5100.38, Airport Improvement Program Handbook, or contact the local FAA Airports District Office (ADO) for information on matters concerning project eligibility. This AC does not establish, modify, or address project eligibility under any FAA grant program.

1.9.1 Obligations. Airport sponsors agree to certain obligations as a condition for the grant of Federal funds or the conveyance of Federal property for airport purposes. Conformance to the FAA standards in this AC are a factor in determining an airport’s compliance with select obligations. The FAA enforces these obligations through its Airport Compliance Program. Refer to FAA Order 5190.6, FAA Airport Compliance Manual, for additional information on the Airport Compliance Program. For a complete list of assurance obligations, visit the FAA Grant Assurances webpage.

1.10 State Role. Each state has an aeronautical office, or similar department, that oversees civil aviation activities in that state. The degree of involvement varies among states. Typical state activities include:

1. Maintaining state aviation system plans

2. Conducting airport inspections

3. Updating Airport Master Records (FAA Form 5010)

4. Working with local agencies on airport zoning and environmental matters

5. Providing supplemental financial assistance

6. Protecting environmental resources

7. Promoting aviation education

8. Licensing of airports

1.10.1 State Block Grant Program. States participating in the State Block Grant Program (SBGP), under 49 U.S.C. § 47128, State Block Grant Program, assume responsibility for administering AIP

8/16/2024 AC 150/5300-13B Chg 1

Chapter 1. Introduction › 1.12 Related Documents and Federal Regulations.

grants at nonprimary airports. The FAA and each participating state enter into a memorandum of agreement identifying the scope of the agreement and the relative responsibilities of the program. See AC 150/5100-21, State Block Grant Program, for further guidance.

1.10.2 State Standards. In limited circumstances, the FAA approves standards developed by a State for development of non-primary airports.

Title 49 U.S.C. § 47105(c), State Standards for Airport Development, allows the FAA to approve standards a State prescribes for airport development at non-primary airports. This provision excludes the FAA standards for safety of approaches. Once approved by the FAA, the State’s standards apply instead of comparable FAA standards.

Title 49 U.S.C. § 47114(d)(5), Use of State Highway Specifications, prescribes the use of State highway specifications for airfield pavement construction at nonprimary airports serving aircraft not exceeding 60,000 pounds gross weight, provided the FAA determines safety is not adversely affected and the expected service life of pavement is not less than what FAA standards provide. Refer to AC 150/5100-13, Development of State Aviation Standards for Airport Pavement Construction, for additional details.

1.11 Local Government Role. A local government is responsible for the maintenance and operation of the airport it owns or operates. Local government units may have regulations and ordinances affecting airport development and operation. Many local governmental units establish zoning ordinances that benefit the protection of airspace surrounding an airport and persons residing close to an airport. Additionally, local rules may exist for storm water management, building codes, and fire code.

1.12 Related Documents and Federal Regulations. The following are links to comprehensive lists of documents referenced in this AC and additional related information. Unless otherwise stated, non-FAA documents do not supersede FAA regulations, policies or standards. All references to ACs, FAA Orders, and other relevant FAA guidance within this document are to the most recent versions.

1. Advisory Circulars (ACs) are available at https://www.faa.gov/regulations_policies/advisory_circulars/.

2. FAA Orders are available at https://www.faa.gov/regulations_policies/orders_notices/.

3. Federal Regulations are available at https://www.ecfr.gov/.

4. United States Code (U.S.C.) is available at https://www.govinfo.gov/.

8/16/2024 AC 150/5300-13B Chg 1

5. FAA Forms are available at https://www.faa.gov/forms/.

6. Other FAA Documents.

a. Aeronautical Information Manual (AIM), https://www.faa.gov/air_traffic/publications/.

b. Aeronautical Information Publication,

https://www.faa.gov/air_traffic/publications/atpubs/aip_html/index.html.

c. U.S. Chart Supplement (formerly known as Airport/Facility Directory), https://www.faa.gov/air_traffic/flight_info/aeronav/productcatalog/supplement alcharts/AirportDirectory/.

d. FAA Airport Diagrams, https://adip.faa.gov.

e. FAA-H-8083, Glider Flying Handbook.

f. FAA/USDA manual, Wildlife Hazard Management at Airports, https://www.faa.gov/airports/airport_safety/wildlife/resources.

g. Grant Assurances – Airport Sponsors,

https://www.faa.gov/airports/aip/grant_assurances.

7. Non-FAA Documents.

a. Aircraft Owners and Pilots Association (AOPA), Hangar Development Guide, https://www.aopa.org/-/media/Files/AOPA/Home/Supporting-General- Aviation/Get-Involved/Airport-Support-Network/Airport-Support-Network- Aircraft-Hangar-Development-Guide/hangar-planning.pdf.

b. Airport Cooperative Research Program (ACRP) Reports,

http://onlinepubs.trb.org/onlinepubs/acrp/.

c. American Association of State Highway and Transportation Officials (AASHTO), https://www.transportation.org/, M268, Standard Specification for Retroreflective Sheeting for Flat and Vertical Traffic Control Applications.

d. ASTM International D4956, Standard Specification for Retroreflective

Sheeting for Traffic Control, https://www.astm.org/Standards/D4956.htm.

e. ASTM International E810, Standard Test Method for Coefficient of Retroreflection of Retroreflective Sheeting Utilizing the Coplanar Geometry, https://www.astm.org/Standards/E810.htm.

f. Federal Specification FP-14, Standard Specifications for Construction of Roads and Bridges on Federal Highway Projects, https://highways.dot.gov/federal-lands/specs/archives.

g. International Air Transport Association (IATA), Airport Development

Reference Manual (ADRM), https://www.iata.org/.

h. NASA/Aviation Safety Reporting System (ASRS) Directline Issue No. 6,

August 1993, Ground Jet Blast Hazard, https://asrs.arc.nasa.gov/publications/directline/dl6_blast.htm.

8/16/2024 AC 150/5300-13B Chg 1

i. National Fire Protection Association (NFPA) 407, Standard for Aircraft Fuel Servicing, NFPA Catalog Home.

j. NFPA 409, Standard on Aircraft Hangars, NFPA Catalog Home.

k. NFPA 415, Standard on Airport Terminal Building, Fueling Ramp Drainage,

and Loading Walkways, NFPA Catalog Home.

l. Transportation Security Administration document, Recommended Security Guidelines for Airport Planning and Construction, https://www.sskies.org/images/uploads/subpage/PARAS_0004.Recommended _Security_Guidelines_.FinalReport_.v2_.pdf.

m. Transportation Security Administration Information Publication A-001,

Security Guidelines for General Aviation Airports, https://www.tsa.gov/sites/default/files/2017_ga_security_guidelines.pdf.

n. United States Parachute Association (USPA), Basic Safety Requirements

(BSR), https://uspa.org/.

Page Intentionally Blank

Chapter 2. Design Principles › 2.3 Present Needs Versus Future Demand.

CHAPTER 2. Design Principles

2.1 General. Airport design involves identifying aviation demand at an airport and applying FAA standards to the various airport elements. Effective airport design ensures airport development meets aviation needs and environmental considerations while maintaining acceptable levels of safety, efficiency, and capacity.

2.2 Airport Planning Relationship to Airport Design.

2.2.1 Airport design and airport planning are complementary processes. Airport planning provides a framework to guide future airport development. Airport design incorporates FAA design standards in a manner that addresses existing and future airport needs and demands.

2.2.2 The ALP graphically depicts existing airport facilities and infrastructure, as well as proposed development.

2.2.3 Related planning guidance:

1. AC 150/5000-17, Critical Aircraft and Regular Use Determination.

2. AC 150/5020-1, Noise Control and Compatibility Planning for Airports.

3. AC 150/5060-5, Airport Capacity and Delay.

4. AC 150/5070-6, Airport Master Plans.

2.3 Present Needs Versus Future Demand.

2.3.1 The application of airport planning and design criteria has future implications. Airport designs based only on aircraft currently using the airport can severely limit the airport’s ability to accommodate future operations of more demanding aircraft. Conversely, it is not practical or economical to base airport design on aircraft that will not realistically use the airport. Refer to AC 150/5000-17 for guidance related to critical aircraft.

2.3.2 A key factor to consider during airport design is the spatial relationship between a runway and other airport elements such as taxiways, aprons, and airfield structures. This relationship can affect future growth at the airport. Once constructed, it is very costly to relocate airfield infrastructure that conflicts with the operation of more demanding aircraft. Established infrastructure may preclude the airport from benefitting from improved approach procedures.

2.3.3 To limit constraints to future airport development, consider the separation standards for the next most demanding ADG, AAC, TDG, and approach visibility minimums during current airport design activities. Also consider the OFZ needed for aircraft that exceed

8/16/2024 AC 150/5300-13B Chg 1

Chapter 2. Design Principles › 2.6 Design Process.

the RDC (that will use the runway with less than regular use) in order to avoid possible operational controls. See Appendix M.

2.4 Addressing Non-standard Airport Conditions. The FAA expects airport owners to address non-standard conditions through the airport planning process. The FAA acknowledges that conformance to current standards is not always practical. However, the FAA expects airports to continue to investigate mitigation measures, whether in one or multiple phases, and correct the non-standard conditions over time.

1. The FAA expects implementation of new or revised standards to occur through the planning process.

2. If there is an explicit or immediate safety deficiency for a non-standard condition, the FAA expects airport owners to prioritize the mitigation of the safety deficiency using the current standard.

3. Inconvenience does not represent an acceptable justification for non-conformance to standards.

4. Justifications based on impractical conditions do not represent a permanent justification for non-conformance to standards.

2.5 New Construction, Reconstruction, and Rehabilitation.

2.5.1 For airport projects involving new construction or reconstruction, the FAA expects airport owners to meet the FAA standards described in this AC. For the purpose of this AC, reconstruction represents a complete restoration of the original functionality of the facility, resulting in development with a minimum useful life equal to new construction. FAA Order 5100.38 establishes FAA policy on minimum useful life of development funded under the AIP.

2.5.2 For rehabilitation projects, the FAA expects airport owners to meet the FAA standards to the extent practicable. If it is not practical to meet current standards, the FAA expects the airport to develop a plan to meet the standards in the future, per paragraph 2.4. For the purpose of this AC, rehabilitation is a restoration of an original functionality of the facility, resulting in a useful life at least equal to half the minimum useful life of new construction. FAA Order 5100.38 establishes FAA policy on minimum useful life of development funded under the AIP.

2.6 Design Process. The airport design process involves a series of steps that align current airport needs with appropriate development satisfying these needs, taking into consideration safety, capacity, economics, and the environment. The steps generally include the following:

1. Identify critical aircraft (size and AAC, ADG, and TDG).

8/16/2024 AC 150/5300-13B Chg 1

2. Identify reasonably attainable visibility minimums.

3. Establish applicable RDC.

4. Apply appropriate design standards contained in this AC.

2.6.1 Critical Aircraft. As defined in AC 150/5000-17, the critical aircraft is the most demanding aircraft type, or grouping of aircraft with similar characteristics, that make regular use of the airport. Regular use is 500 annual operations including both itinerant and local operations but excluding touch-and-go operations. The critical aircraft enables airport planners and engineers to design the airport to meet the operational needs of the aircraft while applying the applicable standards. The critical aircraft is a single aircraft or a composite of several different aircraft with similar characteristics per logical groupings of AAC, ADG, and TDG, as defined in AC 150/5000-17. Unless otherwise stated in AC 150/5000-17, apply the critical aircraft criteria for the appropriate design standard. Table M-3 in Appendix M relates characteristics to various design components. Refer to AC 150/5000-17 for FAA guidance. Regular-use criteria apply to the determination of the critical aircraft.

2.6.2 Design Precedence. The FAA acknowledges that during planning and design processes, space constraints may limit the ability to meet safety standards while providing the desired flexibility of airport operations. These safety standards include:

1. Safety areas

2. OFAs

3. Runway OFZ surfaces

4. Terminal Instrument Procedures (TERPS) surfaces

5. Separation standards

6. 14 CFR Part 139 requirements

These standards have precedence over lower-priority airport operational areas such as Remain-Over-Night (RON) parking locations, vehicle service roads, ground service equipment storage, and vehicle parking.

2.6.3 Considerations for Visibility Minimums. Although desirable, lower visibility minimums will result in more restrictive design factors such as obstacle limitations and increased separation criteria. Factors determining approach visibility minimums for a runway include the demand for lower minimums, the resulting benefits, and the associated costs.

2.6.4 Visibility Categories. For the purpose of airport design, there are four categories of visibility. Note these categories and definitions do not match with 14 CFR Part 77.

Visual (V). Runways classified as visual are either not suitable for IFR operations or have not been evaluated for IFR operations. Visual runways do not permit a straight-in approach. For the purpose of airport design, runways with circling-only approaches fall under the visual visibility category. Visual runways:

1. Support Visual Flight Rules (VFR) operations only, as well as IFPs with only circling minima;

2. Are unlighted or lighted with Low Intensity Runway Lights (LIRL) or Medium Intensity Runway Lights (MIRL); and

3. Have visual (basic) runway markings, as defined in AC 150/5340-1, Standards for Airport Markings.

Non-Precision Approach (NPA). An NPA is an instrument approach based on a navigation system that provides course deviation information, but no glidepath deviation information. NPA runways:

1. Support IFR approach operations to visibilities of ½ statute mile (0.8 km) or greater and have a HAT no lower than 250 feet (76 m).

2. Rely on NAVAIDs providing lateral only guidance for instrument approaches such as Very High Frequency Omnidirectional Range (VOR), non-directional beacon (NDB), Area Navigation (RNAV) Lateral Navigation (LNAV), localizer performance (LP), and localizer (LOC).

3. Generally, have lengths at least 3,200 feet (975 m) long, with a minimum width based on RDC.

4. Have runway edge lights using LIRL or MIRL.

5. Have non-precision runway markings, as defined in AC 150/5340-1.

Approach Procedure with Vertical Guidance (APV). APV is an instrument approach based on a navigation system that is not required to meet the PA standards of the ICAO Annex 10, but that provides course and glidepath deviation information. Runways classified as APV handle instrument approach operations where the navigation system provides vertical guidance down to 200 feet (61 m) HAT and visibilities to as low as ½ statute mile (0.8 km). APV runways:

1. May apply to the following approach types: Vertical Navigation (VNAV), Localizer Performance with Vertical Guidance (LPV), or RNAV/Required Navigation Performance (RNP).

2. Typically have a length of at least 3,200 feet (975 m) in length and a typical width of at least 60 feet (18.3 m).

Chapter 2. Design Principles › 2.7 Key Safety Considerations for Airport Design.

3. Typically have a runway with at least a MIRL and non-precision runway markings, as defined in AC 150/5340-1.

Precision Approach (PA). A PA is an instrument approach based on a navigation system that provides course and glidepath deviation information. Runways classified as precision, handle instrument approach operations supporting an instrument approach with a HAT lower than 250 feet (76 m) and visibility lower than ¾ statute mile (1.2 km), down to and including Category (CAT) III. Precision Instrument Runways (PIRs):

1. Support IFR operations with visibilities down to and including CAT-III with the appropriate infrastructure.

2. Have navigational systems capable of supporting precision operations that include instrument landing system (ILS) and Ground Based Augmentation System (GBAS) Landing System (GLS). (FAA Order JO 6850.2, Visual Guidance Lighting Systems, contains descriptions of various approach lighting systems.)

3. Have runway lengths of at least 4,200 feet (1280 m).

4. Have minimum runway width of at least 75 feet (22.9 m) with the typical width being 100 feet (30.5 m).

5. Have High Intensity Runway Lights (HIRL).

6. Have precision runway markings, as defined in AC 150/5340-1.

2.6.5 Establish Applicable RDC. Establishing the critical aircraft and justified visibility minimums establishes the RDC. Determine an RDC for each runway at the airport, per paragraph 1.6.4.

2.6.6 Apply Applicable Design Standards. The RDC determines the applicable standards for runway design. Each runway will have a specific RDC establishing design criteria such as runway to taxiway separations, safety areas, OFAs, and OFZs.

Example. Consider that an airport may have a runway for air carrier operations and a runway for GA operations. The runway serving air carrier operations may have an RDC of D-IV-2400 while the runway serving GA operations may have an RDC of B-II-5000.

2.7 Key Safety Considerations for Airport Design.

2.7.1 Runway Incursions. A runway incursion is any occurrence involving the incorrect presence of an aircraft, vehicle, or person in a protected area designated for the landing or takeoff of aircraft.

Chapter 2. Design Principles › 2.8 Modification of Standards.

8/16/2024 AC 150/5300-13B Chg 1

Airfield geometry is a factor affecting the risk associated with runway incursions. Appropriate consideration of this aspect during runway and taxiway design can mitigate the factors that lead to increased risk of runway incursions.

1. Refer to Chapter 3 and Appendix J for taxiway design practices that reduce the risk of runway incursions.

2. Certain runway configurations can increase the risk of runway incursions. Such configurations include, but are not limited to:

• Close proximity of thresholds • Closely spaced parallel runways • Wide expanses of pavement between intersecting runways.

2.7.2 Wrong Surface Events. A wrong surface event is an occurrence when an aircraft lands or departs, or tries to land or depart, on the wrong runway or on a taxiway. The causal factors for such events are broad. As it relates to airport design, airfield pavement geometries may contribute to wrong surface events. See paragraphs 4.6 and 4.8. Some considerations that can increase the risk of wrong surface events include:

1. The width of a parallel taxiway plus its shoulders may visually appear as a runway to a pilot on final approach to the associated runway.

2. The presence of pavement wider than standards:

a. Can obscure the location of the landing threshold due to inadequate contrast, and

b. Can draw a pilot’s attention to an incorrect runway for landing.

3. The presence of a wide expanse of pavement fillet causing the pilot to mistake a parallel taxiway as the runway.

4. Parallel runways without standard separation distance.

5. Close proximity of thresholds of non-parallel runways.

6. The low visual contrast of runway pavement as compared to surrounding pavements and landscape.

2.8 Modification of Standards. Site-specific conditions may make it impractical to meet all FAA design standards at an airport. The FAA considers, on a case-by-case basis, modifications to design standards that result in an acceptable level of safety and efficiency. Specific operational controls may be necessary to establish an acceptable level of safety for operation of aircraft at the airport. FAA Order 5300.1 establishes FAA policy for administering airport requests for modification of standards. See paragraphs 2.4 and 2.5.

2.8.1 The FAA views an approved modification of standards as an interim measure intended to mitigate unique site-specific conditions. Unless the FAA explicitly states otherwise in the approval action, the FAA expects airports with approved modifications to pursue

Chapter 2. Design Principles › 2.10 Diverse Aeronautical Activities on Airports.

ways to meet design standards. This may occur incrementally over time or at such time it becomes practical to correct the non-standard condition.

2.8.2 The FAA will not consider any request to modify design standards associated with the following:

1. RSA dimensions

2. OFZ dimensions

3. Approach or departure surface dimensions

4. Standards established within a regulation (e.g., stopway, clearway).

2.8.3 An airport seeking FAA approval of modification to a design standard submits a request using the Modification of Standards application tool within the Airport Data and Information Portal (ADIP) at https://adip.faa.gov. The FAA relies on the following information, in part, to determine the acceptability of a modification to FAA design standards:

1. Information on the standard proposed for modification.

2. Description of proposed modification and why the airport cannot meet standards.

3. Statement addressing how modification will provide an acceptable level of safety, economy, durability, and workmanship.

4. Listing of any special operational measures necessary to accommodate the modification.

2.9 Safety Management Systems (SMS). FAA Order 5200.11, FAA Airports (ARP) Safety Management System (SMS), establishes FAA policy for the implementation of SMS within the FAA’s Office of Airports (ARP). Among other things, this Order describes when Safety Risk Management practices apply to ARP-produced airport standards and project-specific approvals and provides procedures thereto.

2.10 Diverse Aeronautical Activities on Airports. Airports can support a diverse range of aeronautical activities. In addition to aircraft operations, aeronautical activities may include powered-parachutes, helicopters, parachute drop zones, balloons, gliders, weight-shift-control aircraft, airships, banner towing, and others. Some of these aeronautical activities use airport operational surfaces in a non-typical manner. FAA Order 5190.6, FAA Airport Compliance Manual, provides guidance on reasonably accommodating these activities while addressing safety concerns and related considerations including coordination with other FAA offices such as Flight Standards and the ATO.

2.10.1 Heliports/Helipads. Refer to AC 150/5390-2, Heliport Design, for guidance on helicopter facilities on airports. This AC provides helipad dimensions, as well as recommended distances between the helicopter final approach and takeoff area to the runway centerline.

2.10.2 Light Sport Aircraft (LSA). LSA generally have greater aeronautical capabilities than ultralights, while being lighter than GA aircraft certified under 14 CFR Part 23, Airworthiness Standards: Normal Category Airplanes, and 14 CFR Part 27, Airworthiness Standards: Normal Category Rotorcraft. FAA Order 8130.2, Airworthiness Certification of Aircraft, establishes policies and procedures for LSA. The FAA bases certification of LSAs on accepted industry consensus standards. For aircraft operating under LSA rules, use the standards in this AC for small aircraft with approach speeds of more than 50 knots.

2.10.3 Ultralights. Title 14 CFR Part 103, Ultralight Vehicles, regulates ultralight aircraft. Maximum takeoff weight is less than 254 lbs (115 kg) and maximum stall speed is not more than 24 knots. Use the standards in this AC for small aircraft with approach speeds of less than 50 knots. Refer to AC 103-6, Ultralight Vehicle Operations-Airports, ATC, and Weather, for operational guidance.

2.10.4 Seaplanes. Refer to AC 150/5395-1, Seaplane Bases.

2.10.5 Parachute Operations. Parachute operations are a permissible aeronautical activity at Federally obligated airports subject to compliance with reasonable terms and regulatory requirements. Per 14 CFR Part 105, Parachute Operations, parachute operations on an airport require prior approval from the airport operator. Refer to FAA Order 5190.6 for FAA policy addressing reasonable accommodation of parachute operations at an airport, safety considerations, and coordination with other appropriate FAA offices. Additional resources for information on parachute operations as it relates to airport design include:

• FAA Order JO 7110.65, Air Traffic Control. • FAA Order JO 7210.3, Facility Operation and Administration. • AC 150/5190-7, Minimum Standards for Commercial Aeronautical Activities. • AC 105-2, Sport Parachuting. • AC 90-66, Non-Towered Airport Flight Operations. • United States Parachute Association (USPA), Basic Safety Requirements (BSR), https://uspa.org/

8/16/2024 AC 150/5300-13B Chg 1

2.10.6 Aircraft Operations in the Unpaved Runway Safety Area (RSA). The primary function of a standard RSA is to enhance the safety of aircraft that undershoot, overrun, or veer off the runway. Pilots of certain aircraft (such as ultralights, powered-parachutes, helicopters, gliders, agricultural aircraft, tailwheels, aircraft with large balloon type “tundra” tires, etc.) occasionally use the unpaved portion of the RSA adjacent to a runway for takeoffs, landings, or other operations (e.g., banner towing). While aircraft operations from the unpaved portion of an RSA are not inherently unsafe, such operations have the potential to introduce various hazards and risks to the pilot, as well as other aircraft, vehicles, individuals, and facilities on the airport.

Key risk factors to consider include:

1. The separation standards of Tables G-1 through G-12 in Appendix G do not consider landing and takeoff operations from the RSA adjacent to the paved runway surface.

2. Aeronautical studies do not cover operations to and from the RSA adjacent to the paved runway.

From an airport design perspective, the optimum approach for an airport with a demonstrated need for operations from a turf surface is the development of a standard turf runway, per paragraph 3.20. Runway justification conditions and regular-use criteria apply if the airport desires Federal assistance with development of a turf runway.

AIP Airport Sponsor Grant Assurance 19 requires the owner of an airport developed with Federal grant assistance to operate its airport at all times in a safe and serviceable condition. Refer to AC 150/5000-17. An airport with operations in the RSA adjacent to the runway pavement may need to assess the operational safety implications, with assistance from the FAA, to ensure an acceptable level of safety.

FAA Order 5190.6 establishes FAA policy for reasonably accommodating these activities while addressing safety considerations and coordination with other FAA offices. Flight Standards, working in conjunction with the Office of Airports and/or ATO, will analyze supporting data and documentation to determine whether conducting a particular activity at an airport results in an acceptable level of safety.

The Flight Procedures and Airspace Group (FPAG) specialist serves as the initial point of contact for a safety assessment. The FPAG engages other Flight Standards offices, as appropriate, to assess and determine if an acceptable level of safety for aircraft operations within the unpaved portion of an RSA exists. In many cases, current FAA regulations, guidance, and operational procedures are sufficient to establish an acceptable level of safety. In other cases, operational mitigations are necessary based on Flight Standards safety assessment and guidance.

8/16/2024 AC 150/5300-13B Chg 1

Contact the applicable FPAG specialist for questions related to the safety of aircraft operations within the unpaved portion of an RSA. See https://www.faa.gov/about/office_org/headquarters_offices/avs/offices/afx /afs/afs400/afs420 for FPAG contact information.

Airport design standards do not account for these types of operations. Consider the following factors when assessing aircraft operations in the RSA:

1. Education of the pilot community to reflect an operation in the RSA adjacent to the paved runway surface represents an operation on the paved runway.

2. The separation values and hold line locations on the runway side, where RSA operations occur, may be inadequate to mitigate identified risk.

3. Provision for enhanced inspection and maintenance of the RSA to ensure a serviceable condition.

4. Provision of airport informational notes in the Chart Supplement and Automatic Weather Observation Systems (AWOS) broadcasts.

5. Provisions based on State laws on landing and takeoff areas.

6. Consultation with the Part 139 inspector at certificated airports.

2.10.7 Emerging Entrants into the National Airspace System The effect emerging entrant systems have on airport design will evolve over time. Stay current with technology advancements to understand impacts to airport design.

Unmanned Aircraft Systems (UAS). See https://www.faa.gov/uas/ or contact the appropriate FAA Regional or Airports District Office for guidance.

Advanced Air Mobility (AAM). See https://www.faa.gov/air-taxis or contact the appropriate Regional or Airports District Office for guidance.

2.10.8 Gliders. The airport design standards that apply to powered aircraft apply to gliders as well, including self-launching gliders. The long wing lengths and low wingtip clearance common with gliders may present conflicts with airport infrastructure (e.g., lights, signs, etc.) whenever the glider is not the critical aircraft meeting regular use criteria.

Similar to an aircraft at a runway holding position, a glider and its associated tow vehicle may stage in a ROFA. However, support equipment such as vehicles, trailers, stands, dollies, etc., represent objects that need to be clear of active safety areas, OFAs, and OFZs.

Refer to FAA document FAA-H-8083, Glider Flying Handbook, for additional considerations related to operations on the airport.

Contact the appropriate FAA Regional Office or ADO for additional guidance regarding site-specific safety assessments. Safety assessments typically involve engagement of the FAA Flight Standards Service.

2.10.9 Military Operations at Civil Airports. The standards in this AC apply to civilian aeronautical activities. For airports with military operations, consult the appropriate DoD Agency for guidance related to military design criteria. Refer to AC 150/5000-17 for FAA guidance addressing how to handle military operations for critical aircraft determination.

Page Intentionally Blank

Chapter 3. Runway Design › 3.3 Runway Design Standards.

CHAPTER 3. Runway Design

3.1 General. The runway design standards, recommendations, design considerations, and requirements in this chapter describe features essential for safe and efficient takeoff and landing operations.

3.2 Runway Design Code (RDC). The RDC determines the standards that apply to a specific runway and parallel taxiway allowing optimal safe operations by the critical aircraft under desired meteorological conditions. The RDC is based on existing and planned development and does not have any operational application.

3.3 Runway Design Standards. Refer to Appendix G or the online Runway Design Standards Matrix Tool for specific dimensional design standards. Refer to Figure 3-1 for an illustration of design standard dimensions using an airport layout example. Unless otherwise noted, dimensional standards are independent of the surface type of the runway. The links in Table 3-1 navigate the user to the corresponding design code table in Appendix G.

Table 3-1. Runway Design Standards

ADG-I ADG-II ADG-III ADG-IV ADG-V ADG-VI

A-I Small A-II Small - - - -

A-I A-II A-III - - -

Figure 3-1: picture of page 60Figure 3-1 · page 60
Picture of the page from the copy saved here

B-I Small B-II Small - - - -

B-I B-II B-III B-IV - -

C-I C-II C-III C-IV C-V C-VI

D-I D-II D-III D-IV D-V D-VI

E-I E-II E-III E-IV E-V E-VI

Alternatively, see the online Runway Design Standards Matrix Tool.

Figure 3-1. Airport Layout Example

See Appendix G or online Runway Design Standards Matrix Tool for dimensions.

Runway protection zone

LEGEND:

RSA:

P - Approach end (typ) R - Departure end (typ)

200 ft (61 m)

Taxiway centerline (typ)

RPZ: ROFA:

L (typ)

A Runway

length

(typ)

200 ft (61 m)

B (typ)

G

Apron

H

D (typ)

Runway C

U (typ)

V (typ)

Q (typ)

C (typ)

L

Runway CL

Chapter 3. Runway Design › 3.4 Runway Design Concepts and Considerations.

3.4 Runway Design Concepts and Considerations.

3.4.1 Runway Length. Use AC 150/5325-4, Runway Length Requirements for Airport Design, to determine the runway length for the critical aircraft. Key design factors include:

1. Critical aircraft takeoff and landing distances.

2. Obstacle clearance for all aircraft intended to use the runway.

3. Airport elevation.

4. Airport climate condition.

5. Surface gradient.

3.4.2 Runway Threshold. Runway length, obstructions, and visibility requirements are key factors when locating a runway threshold.

1. The appropriate approach and departure surfaces are clear of obstacles.

2. Operational mitigations may be necessary to address obstacle penetrations of standard approach surfaces.

3. Refer to paragraph 3.6 and Table 3-2, Table 3-3, Table 3-4, and Table 3-5 for runway approach and departure standards.

3.4.3 Number of Runways. Runway location and orientation are paramount to airport safety, efficiency, economics, and environmental impact. Capacity and/or wind coverage determine the number of runways needed.

Capacity Use AC 150/5060-5 for planning guidance on runway capacity.

Orientation and Wind. The primary runway orientation is normally in the direction of the prevailing wind. A wind data analysis considers wind speed and direction for existing and forecasted operations for local meteorological conditions.

1. Refer to Appendix B for wind analysis for airport planning and design.

2. Design for a crosswind runway when the primary runway orientation:

a. provides less than 95.0 percent wind coverage during all weather conditions, and

b. regular use for the critical aircraft needing crosswind coverage

exists, per AC 150/5000-17.

3. Wind coverage is based on the allowable crosswind component not exceeding the values in Table B-1.

3.4.4 Airspace Analysis and Obstruction to Air Navigation. The runway orientation determines the approach and departure path for the design level of service. An obstruction survey identifies objects that may affect aircraft operations in this path. Contact the local FAA Regional Office or ADO for assistance and information regarding the following matters:

• Existing and planned IFPs • Missed approach procedures • Departure procedures • Traffic patterns influencing airport layouts and locations • Obstructions to air navigation

3.4.5 Environmental Factors. An evaluation under the NEPA considers the impact of runway development on existing and proposed land use, noise on nearby residents, air and water quality, wildlife, and historical/archeological features. FAA Order 1050.1 and FAA Order 5050.4 establish FAA policies and procedures for complying with the NEPA.

3.4.6 Topography. Topography affects:

1. The amount of grading and drainage work necessary to develop a runway, both existing and long term. See AC 150/5320-5, Airport Drainage Design, for further guidance.

2. IFPs when it is necessary to increase minima to keep flight paths clear of terrain in the approach surfaces.

a. The presence of precipitous terrain may also result in increased minima to provide additional clearance.

b. For takeoff, establishing an obstacle departure procedure may be needed when

operating under IFR to ensure safe clearance from rising terrain.

Continue reading ↓ 120 of 628 passages shown