Radar Vectors
Advisory Circular Current Issued May 10, 2019 AAS-100 175 pages Copy saved Nov 18, 2026

AC 150/5340-1M Standards for Airport Markings

This AC contains the FAA standards for markings used on airport runways, taxiways, and aprons. Consolidated to include Change 1, dated December 23, 2020.

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Standards for Airport Markings Date: 12/23/2020 Initiated By: AAS-100

AC No: 150/5340-1M Change: 1

1 Purpose. This advisory circular (AC) change contains the Federal Aviation Administration (FAA) standards for markings used on airport runways, taxiways, and aprons.

2 Applicability. No change to paragraph 3, Applicability, dated 5/10/2019.

3 Principal Changes. The AC change incorporates the following principal changes:

1. Page vi, paragraph 5, Implementation, subparagraph 4 replaced as shown below.

2. Paragraph 3.5.1 appended to add four new subparagraphs 3.5.1.1, 3.5.1.2, 3.5.1.3, and 3.5.1.4.

4 Implementation. Implement changes addressed by this change upon effective date of this AC except as noted in Implementation subparagraph 1, dated 5/10/2019, and by the following revised subparagraph 4:

4. Paragraph 3.5, Approach/Departure Holding Position Marking.

a. Delay implementation of the APCH/DEP conditional marking and associated signage until FAA updates the following aeronautical publication for conditional holding positions: Aeronautical Information Manual (AIM); FAA Orders JO 7110.65, Air Traffic Control, and JO 7210.3, Facility Operation and Administration.

b. Implementation of approach/departure holding positions involves a process that includes: FAA assessment of affected runways and taxiways; advance

ii

coordination with local ATC for development of a local standard operating procedure (SOP); local controller training and, as applicable, updates to the part 139 sign and marking plan. Upon completion of an assessment, FAA provides notification to the airport if conditional holding positions are necessary for protection of the approach/departure area.

c. Upon receiving notification from the FAA of the need for conditional holding positions in the approach/departure area, implement the necessary changes to the holding position marking as follows:

i. For airports with operating airport traffic control towers and airports certified under 14 CFR Part 139, implement the necessary changes within two years from the date of FAA notification.

ii. For Federally obligated airports without an operating airport traffic control tower and non-certificated airports, implement marking changes with the next planned airfield development project.

5 Feedback on this AC. If you have suggestions for improving this AC change, you may use the Advisory Circular Feedback form at the end of this AC.

John R. Dermody Director of Airport Safety and Standards

Advisory U.S. Department of Transportation Federal Aviation Circular Administration

Consolidated AC includes Change 1

Subject: Standards for Airport Markings Date: 5/10/2019 Initiated By: AAS-100

AC No: 150/5340-1M Change:

1 Purpose. This advisory circular (AC) contains the Federal Aviation Administration (FAA) standards for markings used on airport runways, taxiways, and aprons.

2 Cancellation. This AC cancels AC 150/5340-1L, Standards for Airport Markings, dated September 27, 2013.

3 Applicability. The Federal Aviation Administration recommends the standards and guidelines in this AC to establish uniform application of airfield surface markings for runways, taxiways and aprons. This AC does not constitute a regulation, is not mandatory and is not legally binding in its own right. It will not be relied upon as a separate basis by the FAA for affirmative enforcement action or other administrative penalty. Conformity with this AC is voluntary, and nonconformity will not affect rights and obligations under existing statutes and regulations, except for the projects described in subparagraphs 2, 3 and 4 below:

1. The standards and guidelines contained in this AC are practices the FAA recommends to establish an acceptable level of safety, performance and operation for airfield ground navigation.

2. This AC provides one, but not the only, acceptable means of meeting the requirements of 14 CFR part 139, Certification of Airports.

3. Use of these standards and guidelines is mandatory for projects funded under Federal grant assistance programs, including the Airport Improvement Program (AIP). See Grant Assurance #34.

iv

4. This AC is mandatory, as required by regulation, for projects funded by the Passenger Facility Charge program. See PFC Assurance #9.

4 Principal Changes. The AC incorporates the following principal changes:

1. New criterion for centering runway landing designators (common industry practice). See paragraph 2.3.5 and the green instructional box titled “Centering of Runway Landing Designators, Width of Rectangular Boxes (Painting).”

2. Paragraph 1.2, no-taxi islands definition. Added new definition to define no-taxi islands applicable to this advisory circular.

3. Paragraph 1.3.2. Added new red safety box informing airport operators not to apply preformed thermoplastic markings on the runway due to their significant reduction in pavement friction as compared to bare pavement.

4. Paragraph 1.3.8. The advisory circular makes the recommendation for training of personnel that perform application of surface markings, prepare surfaces to receive surface markings, remove markings, etc., as important aspects to obtaining desired markings and longevity.

5. Paragraph 1.3.9. Added new paragraph to clarify that all surface markings painted by the use of stencils are not to leave stencil gaps.

6. Paragraph 1.4. Added new notes to Table 1-2 that clarifies the relationship of Table 1-2 with Table 1-1 when dealing with the requirements for black borders.

7. Paragraph 1.5. Added new paragraph explaining the functions and applications of no-taxi islands to mitigate runway incursions and taxiing excursions. Deleted previous no-taxi island criteria from paragraph 4.4.5.2 and paragraph 4.10.4. Revised the red safety box in paragraph 4.4.5.2 to reference new paragraph 1.5 criteria.

8. Paragraphs 2.1.1. Added “Engineered Materials Arresting Systems (EMAS)” to the end of the paragraph as another example of paved areas prior to the runway end (start of runway). Clarified that Table 2-1 applies to runways that lack stopways, blast pads, displaced thresholds, or aligned taxiways.

9. Paragraph 2.9. Revised text in subparagraphs 2.9.1 and 2.9.2 to clarify the functions of a displaced threshold, the location where a displaced threshold begins as compared to a non-displaced threshold, and the use of arrow shafts.

10. Paragraphs 3.1 and 3.5. Pattern A is replaced by the Pattern B surface marking to protect the Approach/Departure Areas of the runway. This interchange is a direct result from the FAA Technical Center R&D report DOT/FAA/TC-16/26, Evaluation of Enhanced Visual Cues for Runway Approach and Runway Safety Areas, published in April 2016. This change in pattern will be accompanied with the installation of a new vertical sign to be promulgated by a change to AC 150/5340-18G.

v

11. Paragraph 4.3.4. Revised text to align FAA criterion with International Civil Aviation Organization (ICAO) Annex 14, Volume I criterion for enhanced taxiway centerline surface markings that are collinear with on-centered surface painted holding position signs. Revised Figure D-6 to reflect new criterion.

12. Paragraph 4.3.4. Added an instructional green box with guidance on how to relocate surface painted holding position signs between the two taxiway width categories (off-taxiway centerline placement and on-taxiway centerline placement).

13. Paragraph 4.4.5.4.2. Replaced criterion for the case not outlined in black when a taxiway edge marking is located at a runway holding position to read – a 6-inch (12 cm) gap is left between the holding position marking and the taxiway edge marking.

14. Paragraph 4.11.3.1. Replace 600 RVR with 500 RVR to agree with FAA Order 7110.65, Air Traffic Control (latest edition).

15. Paragraph 5.3.5, Item 4. Replaced the word “interior” with “exterior.”

16. Paragraph 5.6.1. Added more guidance regarding when to remove existing runway markings when a runway is closed or from an intersecting runway that has been closed.

17. Figures as follow:

a. Figure A-10 and Figure A-11 added the word “Displaced” to the phrase

“Runway Threshold Bar (white)”;

b. Figure A-12 added the word “Yellow” to Note 2;

c. Figure A-13 added the word “each” to the phrase “2 Lines and 1 Space are each

12” [30 cm] Wide”;

d. Figure A-16 added to Note 3 the reference to paragraph 320 of AC 150/5300-

13, Airport Design;

e. Figure A-18 clarified the design criterion to build taxiway/taxiway intersections

with cockpit-over centerline fillets and marking criterion to use curved taxiway centerline markings by added the phrase “until such substandard fillets are widened to full standard design criteria” to the end of the existing phrase “Taxiway centerline markings at intersection having less than standard fillets and requiring judgmental over steering”;

f. Figure A-19 redrawn to emphasize the design criteria for standard width of

taxiway entrances with a no-taxi island between entrance taxiways to a runway and for the elimination of paved areas within a POFZ;

g. Figure A-23 added the pictorial symbol for a vertical sign to reinforce

placement of a vertical sign at runway holding position locations;

h. Figure D-5, Figure D-7, and Figure D-8 added the phrase “The SPHPS to the

right of the taxiway centerline is not always required in most cases.” to the table within the first row.

i. Figure D-6 revised to show new marking pattern per ICAO Annex 14. Introduced new dimension “D” and removed taxiway centerline marking

vi

between the surface painted holding position sign (SPHPS) and the runway holding position marking (Pattern A).

18. The format of the document has been updated in this version, and minor editorial changes have been made throughout.

5 Implementation. Implement changes addressed by this revision upon effective date of this AC except as noted by the following:

1. Paragraph 2.3.5. FAA expects airports certificated under Part 139 to apply the guidelines for centering runway landing designator markings upon the next repainting project.

2. Paragraph 1.3.2, Preformed Thermoplastic Surface Marking on Runways. In the case of existing preformed thermoplastic markings on a runway, FAA expects airports certified under Part 139 to correct such applications within one year of the effective date of this change.

3. Paragraph 1.3.9, Stencil Templates. For instances of existing surface markings with stencil gaps, FAA expects airports certified under Part 139 to correct existing stencil gaps during the next painting project.

4. Paragraph 3.1, Approach/Departure Holding Position Marking. Implementation of the APCH/DEP signage and marking will employ a delayed approach to allow time for stakeholder outreach and familiarization activities to take place.

a. Delay installation of APCH/DEP signage and marking until after January 1, 2021.

b. For airports certified under 14 CFR Part 139 and those with an air traffic control tower, FAA expects conformance to the standards of paragraph 3.5 no later than December 31, 2022.

c. Non-towered, general aviation airports may defer action on conforming to paragraph 3.5 until the next planned development project at the airport (i.e., signage and marking project, or pavement rehabilitation project).

5. Paragraph 4.3.4, Enhanced Taxiway Centerline Surface Marking. FAA expects airports certificated under Part 139 to conform to Figure D-6 for enhanced taxiway centerline surface marking collocated with on-center surface painted holding position signs when carrying out the next repainting project.

6 How to use this AC.

1. This AC includes color-coded text boxes to emphasize safety initiatives, solutions to painting difficulties, and general remarks.

a. Green (Painting) – explains painting precautions and solutions, such as when proportioning is permissible for runway surface markings.

b. Red (Safety) – emphasizes safety initiatives.

vii

c. Gray (General) – contains general remarks.

2. All references to other FAA ACs and Orders are interpreted as the current version.

3. Most figures in this AC are full scale AutoCAD drawings saved as MS Word versions. For some figures, certain details may appear to be missing (missing or broken lines) when either printed or viewed on a computer monitor. To view all the details in these figures, use the appropriate ZOOM function. In some instances, where there is a large surface area, a ZOOM value of over 250% may be necessary to view all details. Both this AC and the original AutoCAD files for all figures are available for download at the FAA web site: http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.lis t/parentTopicID/85.

4. Hyperlinks (allowing the reader to access documents located on the internet and to maneuver within this document) are provided throughout this document and are identified with underlined text. When navigating within this document, return to the previously viewed page by pressing the “ALT” and “ ←” keys simultaneously.

7 Measurements in this AC. This AC uses U.S. customary units followed with “soft” (rounded) conversion to metric units. The U.S. customary units govern.

8 Copies of this AC and Other FAA Publications. You can view a list of all ACs at http://www.faa.gov/regulations_policies/advisory_circulars/. You can view the Federal Aviation Regulations at http://www.faa.gov/regulations_policies/faa_regulations/.

9 Feedback on this AC. If you have suggestions for improving this AC, you may use the Advisory Circular Feedback form at the end of this AC.

/signed/

John R. Dermody Director of Airport Safety and Standards

viii

Page Intentionally Blank

CONTENTS

Number Page

ix

Chapter 1. Surface Markings for Airfield Pavements and Paved Airfield Roadways.

… 1-1

Chapter 2. Surface Markings for Runways … 2-1

Chapter 3. Holding Position Markings … 3-1

CONTENTS

Number Page

x

Chapter 4. Surface Markings for Taxiways … 4-1

Chapter 5. Other Surface Markings … 5-1

CONTENTS

Number Page

xi

Appendix A. Pavement Markings … A-1

Appendix B. Inscriptions for Signs and Geographic Position Markings … B-1

Appendix C. Examples of Markings Outlined in Black … C-1

Appendix D. Enhanced Markings for Runway Holding Position … D-1

FIGURES

Number Page

Figure 1-1. Example of Marking Removal Patterns … 1-4

Figure 1-2. Example of Marking Removal Patterns … 1-5

Figure 1-3. Example of Marking Removal Patterns … 1-6

Figure 1-4. Example of Marking Removal Patterns … 1-7

Figure 1-5. Example of Painted Numbering System for Surface Painted Markings … 1-8

Figure 1-6. Case 1 … 1-18

Figure 1-7. Case 2 … 1-19

Figure 1-8. Case 3 … 1-20

Figure 1-9. Case 4 … 1-21

Figure 2-1. V Geometry … 2-4

Figure 4-1. Sequential Circular-Shaped Apron Control Markings 3, 4, and 5 Between Two

Terminals … 4-28

Figure 4-2. Circular-Shaped Apron Control Marking 16 on Elongated Terminal Apron … 4-29

Figure 4-3. Circular-Shaped Apron Control Markings 9S and 9N Between Terminals … 4-30

Figure 4-4. Triangular-Shaped Apron Control Marking Between Terminals … 4-32

Figure 4-5. Circular and Triangular-Shaped Apron Control Marking Dimensions … 4-33

Figure 5-1. Precautionary Placement of the Non-Movement Boundary Marking … 5-4

CONTENTS

Figure 1-1: picture of page 11Figure 1-1 · page 11
Picture of the page from the copy saved here

Number Page

xii

Figure 5-2. TAXI Marking Location Facing Runway Approach End … 5-11

Figure 5-3. TAXI Marking Dimensions … 5-12

Figure 5-4. Aviation Grade Artificial Turf Installation … 5-13

Figure A-1. Precision Runway Markings … A-1

Figure A-2. Non-Precision Runway … A-2

Figure A-3. Visual Runway Markings … A-3

Figure A-4. Example of Conflicting Markings on Crossing Runways … A-4

Figure A-5. Details of Markings for Intersecting Runways … A-5

Figure A-6. Runway Designation Numerals and Letters … A-6

Figure A-7. Displaced Threshold Markings … A-7

Figure A-8. Marking for Aligned Taxiway with Runway without a Displaced Threshold … A-8

Figure A-9. Markings for Blast Pads and Stopways … A-9

Figure A-10. Markings for Aligned Taxiway Preceding a Displaced Threshold … A-10

Figure A-11. Markings for Blast Pad Preceding a Displaced Threshold … A-11

Figure A-12. Runway Shoulder Markings … A-12

Figure A-13. Holding Position Marking Details … A-13

Figure A-14. Holding Position Marking Details … A-14

Figure A-15. Taxiway Markings … A-15

Figure A-16. Taxiway Markings … A-16

Figure 5-2: picture of page 12Figure 5-2 · page 12
Picture of the page from the copy saved here

Figure A-17. Taxiway Markings … A-17

Figure A-18. Methods for Taxiway Centerline Marking … A-18

Figure A-19. Surface Painted Direction Signs … A-19

Figure A-20. Surface Painted Gate Identification Signs … A-20

Figure A-21. Multiple Gate Signs … A-21

Figure A-22. Surface Painted Apron Entrance Point Signs … A-22

Figure A-23. Taxiway Shoulder Markings … A-23

Figure A-24. Geographic Position Markings … A-24

Figure A-25. Vehicle Roadway Markings … A-25

Figure A-26. VOR Receiver Checkpoint Markings … A-26

Figure A-27. Closed Runway and Taxiway Markings … A-27

CONTENTS

Number Page

xiii

Figure B-1. Pavement Markings ABCDEFGH … B-1

Figure B-2. Pavement Markings IJKLMNOP … B-2

Figure B-3. Pavement Markings QRSTUVWX … B-3

Figure B-4. Pavement Markings YZ123456 … B-4

Figure B- 5. Pavement Markings 7890-, ↑ … B-5

Figure C-1. Runway Holding Position Marking … C-1

Figure C-2. ILS Holding Position Marking … C-1

Figure C-3. Continuous Taxiway Edge Line Marking … C-2

Figure C-4. Dashed Taxiway Edge Line Marking … C-2

Figure C-5. Alternate Outlining Method for Dashed Taxiway Edge Line Marking … C-3

Figure C-6. Taxiway Centerline Marking … C-3

Figure C-7. Intermediate Holding Position Markings … C-4

Figure C-8. Non-Movement Area Boundary Marking … C-4

Figure D-1. Enhanced Taxiway Centerline Marking on Curved Taxiway … D-2

Figure D-2. Dashed Lines at Converging Taxiway Centerlines … D-3

Figure D-3. Converging, Straight, and Curved Enhanced Taxiway Centerlines Intersecting with

Holding Position Marking … D-4

Figure D-4. Extended Runway Holding Position Markings on Taxiways … D-5

Figure D-5. Surface Painted Holding Position Signs for Taxiway Widths Greater than 35 Feet

(10.5 m) … D-6

Figure D-6. Surface Painted Holding Position Sign for Taxiway Widths Equal to or Less than 35

feet (10.5 m) … D-7

Figure D-7. Surface Painted Holding Position Signs When Taxiway Centerline is Not

Perpendicular to Runway Holding Position Marking … D-8

Figure D-8. Surface Painted Holding Position Signs Co-Located with Geographic Position

Marking … D-9

Figure D-9. Two Taxiway Centerlines Converging at a Runway Holding Position Marking . D-10

Figure D-10. Intersection of Two Taxiways at Runway End … D-11

Figure D-11. Intersection of Three Converging Taxiway Centerlines … D-12

Figure D-12. Intersection of Multi-Taxiway Centerlines With Less Than 150 feet (45.7 m)

Between Taxiways … D-13

Figure D-13. Two Taxiway Centerlines Intersecting a Runway Holding Position Marking ... D-14

CONTENTS

Number Page

xiv

Figure D-14. Intersection of Stub Taxiway and Runway … D-15

Figure D-15. Narrow Taxiway Stacked Surface Painted Holding Position Sign … D-16

Figure D-16. Enhanced Taxiway Centerlines When a Taxiway Connects Closely Spaced

Runways … D-17

TABLES

Number Page

Table 1-1. General Guidelines for Painting a Black Border … 1-9

Table 1-2. Guidelines for Black Borders and Glass Beads … 1-10

Table 2-1. Minimum Required Runway Surface Marking Schemes for Paved Runways … 2-1

Table 2-2. Number of Runway Threshold Stripes for Standard Runway Widths … 2-9

Table 2-3. Groupings of Touchdown Zone Markings Required When Installed From One

Threshold … 2-13

Table 2-4. Groupings of Touchdown Zone Markings Required When Installed From Both

Thresholds … 2-14

Table D-1. Notes for Figure D-5 … D-6

Table D-2. Notes for Figure D-6 … D-7

Table D-3. Notes for Figure D-7 … D-8

Table D-4. Notes for Figure D-8 … D-9

CHAPTER 1. SURFACE MARKINGS FOR AIRFIELD PAVEMENTS AND PAVED AIRFIELD

ROADWAYS.

General. This chapter provides the standards for surface markings used on airfield pavements (runways, taxiways, aprons, and paved airfield roadways). The standards for the surface markings assume that runways, taxiways, and aprons are built in accordance to the standard dimensions and layouts (e.g., clearances, fillets) in Advisory Circular (AC) 150/5300-13, Airport Design. The airport operator should expect difficulties when painting surface markings on non-standard infrastructure, such as a runway with a nonstandard width. To assist airport operators, this AC offers a few workable solutions for existing non-standard situations. Surface markings for large airplane parking positions and surface markings for unpaved airfield runways will be addressed at a future date in additional chapters.

Chapter 1. › 1.2 Definitions.

Note: Use the zoom feature to view detail in any figure.

Definitions. The following definitions apply to terms used in this AC.

1. Certificated Airport. An airport that has been issued an Airport Operating Certificate by the FAA under the authority of Part 139.

2. Commercial Service Airports and Passenger Enplanements. Defined in FAA Order 5100.38, Airport Improvement Program Handbook.

3. Displaced Threshold. A threshold that is located at a point on the runway other than the designated beginning of the runway.

4. Island. An unused paved or grassy area along a taxiway, between taxiways, between runways, or between a taxiway and a runway. Paved islands are clearly marked as unusable, either by painting or the use of artificial turf. For the purposes of this AC, certain islands are referred to as “No-taxi” islands.

5. Movement Area. The runways, taxiways, and other areas of an airport that are used for taxiing, takeoff, and landing of aircraft, exclusive of loading aprons and aircraft parking areas (reference Part 139).

6. No-taxi Island. An island that requires safety enhancements, i.e., the use of specific surface markings and/or taxiway design features to mitigate excursions from a taxiway or mitigate runway incursions. Vertical signage and/or lighting may also be required or used.

7. Non-precision Runway. See AC 150/5300-13 for the definition.

8. Precision Runway. See AC 150/5300-13 for the definition.

9. Threshold. The beginning of that portion of the runway that is available for landing. In some instances, the landing threshold may not coincide with the end of the opposite direction runway (see paragraph 1.2).

Chapter 1. › 1.3 Surface Marking Practices.

10. Visual Runway. A runway end without an existing or planned (on the Airport Layout Plan) straight-in instrument approach procedure.

Surface Marking Practices. The following subparagraphs address common practices used in airport markings.

In some situations, these standards may call for markings with different meanings to be

installed close together. Ensure that sufficient space is left between such markings such that an observer will not be confused. Note: The taxiway edge marking and nonmovement area boundary marking never coincide or run side-by-side. See paragraph 5.4.

Increasing the Friction Coefficient of Surface Markings. AC 150/5370-10, Standards for Specifying Construction of Airports, Item P-620, Runway and Taxiway Marking, provides airport operators information to increase the friction coefficient of surface markings. Common practices include the spreading of silica sand on the marked surface immediately after painting and the use of glass beads in the marking materials. Glass beads or silica sand are required when durable markings (epoxy and methyl acrylate based paints) are used. These paints are usually applied at 18 to 30 mils in dry thickness.

Safety Notice No. 1

Reduced Runway Surface Friction Prohibition of Preformed Thermoplastic Surface Markings on Runways

Until further notice, preformed thermoplastic surface markings are not to be within the runway proper because of the significantly lower friction readings recorded on such markings as compared to dry unmarked pavement (see FAA Technical Report DOT/FAA/AR-TN08/22, Evaluation of Thermoplastic Marking Materials). FAA expects airports certified under Part 139 to correct existing non-conforming conditions within one year of issuance of this change.

Paint Color Specifications, Requirements for Surface Preparation, Paint Application

Rates and Methods, and Requirements for Preformed Thermal Plastic Markings. AC 150/5370-10 provides the paint color specifications, requirements for surface preparation, paint application rates, the various methods for applying paint, and the performance requirements for using preformed thermoplastic markings. Precaution: Reflective tapes such as those commonly used for highways and city street applications are not to be used on the airside because of the potential for foreign object damage caused by loosened painted tape.

Striated Markings. Striated markings, which may be used only in areas subject to frost heave, consist of painted stripes 4 inches (10 cm) to 8 inches (20 cm) in width that are separated by

unpainted stripes. The width of the unpainted stripe may not exceed the width of the painted stripe. The width of the painted and unpainted stripes must be the same throughout the specific marking. Each edge of the marking must be a painted stripe. That is, a painted stripe is to begin and end within the width of the markings. Precaution: Because striated markings offer reduced visibility compared to non-striated markings, more frequent maintenance is required to maintain an acceptable level of visibility. Hence, striated markings are never used on Category II and Category III runways. The mixing of striated and non-striated markings is not permitted within a surface marking scheme. For example, in a 2-digit landing designator, one digit cannot be striated while the other is not. It is permitted to mix different marking schemes. For example, the landing designator is striated and the aiming point is not.

Temporary Markings. When selecting a material for temporary markings, consider the difficulty of removing the temporary marking when it is no longer needed. Some airports have had some success using water-based paint. Striated markings may also be used for temporary markings, but they are never used to denote a closed runway or other closed pavement or for Category II or Category III runways. Tape is never to be used as temporary marking.

Removal of Markings. Pavement markings that are no longer needed are not to be painted over but instead are to be physically removed. The FAA does not endorse painting over the old markings because this inadequate practice merely preserves the old marking which, in some cases, has misled pilots and required extra maintenance. Physical removal of markings is achieved by water blasting, shot blasting, sand blasting, chemical removal, or other acceptable means that do not harm the pavement. The physical removal of any old marking(s) must include a predetermined larger size and shape of a removal area that encompasses the old marking(s) and by grouping adjacent markings together into a larger rectangular removal area. The rationale behind this practice is to eliminate the continued visual appearance of the removed marking(s). When a runway end or threshold is being moved, all of the markings that are being removed must be strikingly larger in size, grouped together with adjacent markings, and be rectangular in shape.

For example, use a single, larger rectangular removal area to encompass the entire runway designator 7 or 14L and provide a separate large rectangular area comprising all of the runway threshold markings along with a separate large rectangular area for the touchdown zone markings on the same side of the runway centerline. Also, the size and shape for the removal area for (1) Patterns A, B, and C holding position markings and (2) yellow arrow heads having a runway threshold bar or a runway demarcation bar must be much larger than the marking(s) being removed. For example, use a single, larger rectangular removal area to encompass all yellow arrow heads and the adjacent white runway threshold bar marking. See Figure 1-1, Figure 1-2, Figure 1-3, and Figure 1-4 for examples of marking removal patterns.

Figure 1-1. Example of Marking Removal Patterns

Note: For further details, see paragraph 1.3.6.

Pattern for physically removed markings Markings to be physically removed

Pattern for physically removed markings

Pattern for physically removed markings

Pattern for physically removed markings

Figure 1-2: picture of page 19Figure 1-2 · page 19
Picture of the page from the copy saved here

Pattern for physically removed markings

Markings to be physically removed

Markings to be physically removed

Markings to be physically removed

Markings to be physically removed

Pattern for physically removed markings

Figure 1-2. Example of Marking Removal Patterns

Note: For further details, see paragraph 1.3.6.

Markings to be physically removed

Patterns for physically removed markings

Figure 1-3. Example of Marking Removal Patterns

Notes: For further details, see paragraph 1.3.6.

Aligned taxiway construction is prohibited per AC 150/5300-13. Existing locations should be

rectified.

Pattern for physically removed markings

Markings to be physically removed

Markings to be physically removed

Pattern for physically removed markings

Figure 1-4. Example of Marking Removal Patterns

Note: For further details, see paragraph 1.3.6.

Markings to be physically removed (typical)

Markings to be physically removed

Pattern for physically removed markings

Pattern for physically removed markings

Relocated runway holding position and surface painted holding position markings

Figure 1-3: picture of page 20Figure 1-3 · page 20
Picture of the page from the copy saved here

Painted Numbering System for Record Keeping of Surface Painted Markings. To facilitate the daily inspection, scheduled maintenance, necessary repairs, etc., for surface markings, the airport operator may use a numbering system or alphanumeric system that is located in a corner of the surface marking. Figure 1-5 shows a numbering system adopted by one airport for identifying each surface marking listed in their Sign Plan. If employed, the height of the inscription should be small and inconspicuous to all viewers except an individual standing next to the surface marking.

Figure 1-5. Example of Painted Numbering System for Surface Painted Markings

Personnel involved in the application of airfield surface markings should complete

training which includes surface preparation, removal and application of surface markings, and maintenance standards.

Figure 1-5: picture of page 22Figure 1-5 · page 22
Picture of the page from the copy saved here

Chapter 1. › 1.4 Enhanced Conspicuity of Surface Markings on Concrete Pavements and…

Use of Stencil Templates. All gaps created when painting surface markings using a stencil template must be filled in. For example, the surface painted holding position sign shown in Figure D-5 contains no stencil gaps. Airports certified under Part 139 must rectify any gaps during the next painting project.

Enhanced Conspicuity of Surface Markings on Concrete Pavements and Light Colored Pavements. Surface markings that cannot be seen by pilots and other individuals operating on paved airfield surfaces are ineffective. Two proven techniques that help airport operators enhance the degree of contrast (conspicuity) of surface markings are (1) outlining surface markings with black borders on concrete pavements and light-colored pavements and (2) placing glass beads in paint. However, glass beads are not to be used in black paint, including numerals and inscriptions found in Appendix B. Table 1-1 serves as a general guide for determining when existing asphalt concrete surfaces or asphalt treated surfaces may be classified as a light-colored pavement, i.e., when to outline a required surface marking with a black border.

Table 1-1. General Guidelines for Painting a Black Border

Pavement Surface Type

Age of Pavement Surface 1

New Up to 2 years old Over 2 years old

Portland Cement Concrete Yes Yes Yes

Asphalt Concrete No No Yes

Asphalt Treated No No Yes

Note 1: This table serves only as a general guide since an existing asphalt pavement at one airport location may not experience the same rate of surface color deterioration as at another airport location.

Technique 1 – Outlining Surface Markings with Black Borders on Concrete Pavements

and Light-Colored Pavements. The degree of contrast (conspicuity) between surface markings on light-colored pavements, in particular on concrete pavements and older asphalt pavements, can be increased by outlining all edges of the surface marking with a black border. Appendix C provides illustrations of recommended patterns for various surface markings outlined in black. Black borders, except for enhanced taxiway centerline applications, are 6 inches (15 cm) or greater in width to enhance the conspicuity of certain painted surface markings on concrete pavements and light-colored pavements. The borders for the outside dashes of the enhanced taxiway centerline marking can range from 3 to 6 inches (7.5 to 15 cm). See Table 1-2 for surface markings that are required or recommended to have black borders.

1.4.1.1 Surface Markings that Require Black Borders.

1. Runway centerline marking (per paragraph 2.4).

2. Runway threshold marking (per paragraph 2.5).

3. Runway displaced threshold marking (per paragraph 2.9).

4. Runway threshold bar marking (per paragraph 2.9.1).

5. Runway aiming point marking (per paragraph 2.6).

6. Runway landing designator marking (per paragraph 2.3).

7. Runway touchdown zone markings (per paragraph 2.7).

8. All holding position markings (per paragraphs 3.2, 3.3, 3.4, and 3.5).

9. Intermediate holding position marking for taxiway/taxiway intersections (per paragraph 3.6).

10. All taxiway centerline markings on taxi routes designated as Low Visibility Operations (LVO) surface movement guidance and control system (SMGCS) routes (per paragraph 4.2).

11. Enhanced taxiway centerline marking (per paragraph 4.3).

12. Surface painted holding position sign marking (per paragraph 4.5).

13. Geographic position marking (per paragraph 4.11).

14. Non-movement area boundary marking (per paragraph 5.4).

1.4.1.2 Surface Markings Recommended for Black Borders. This AC strongly recommends outlining all other markings not listed paragraph 1.4.1.1, particularly taxiway centerlines per paragraph 4.2.

Table 1-2. Guidelines for Black Borders and Glass Beads

Marking Black Border Glass Beads

Runway centerline marking (per paragraph 2.4). Required Required

Runway threshold marking (per paragraph 2.5). Required Required

Runway displaced threshold marking (per paragraph 2.9). Required Required

Runway threshold bar marking (per paragraph 2.9.1). Required Required

Runway aiming point marking (per paragraph 2.6). Required Required

Runway landing designator marking (per paragraph 2.3). Required Required

Runway touchdown zone markings (per paragraph 2.7). Required Required

Runway edge marking (per paragraph 2.8). Recommended

Runway demarcation bar marking (per paragraph 2.9.3). Recommended

Marking Black Border Glass Beads

All holding position markings used on runways, taxiways, and holding bays and used to indicate ILS or precision obstacle free zone (POFZ) protected areas (per paragraphs 3.2, 3.3, 3.4, and 3.5).

Required Required

Intermediate holding position marking for taxiway/taxiway intersections (per paragraph 3.6).

Required

Taxiway centerline markings (per paragraph 4.2). Recommended Required

All taxiway centerline markings on taxi routes designated as LVO/SMGCS routes (per paragraph 4.2).

Required Required

Enhanced taxiway centerline markings per paragraph 4.3. Required Required

Taxiway edge marking (per paragraph 4.4). Recommended

Geographic position marking (per paragraph 4.11). Required Required

Surface painted signs for holding position signs (paragraph 4.5), taxiway direction signs (paragraph 4.6), taxiway location signs (paragraph 4.7), gate destination signs (paragraph 4.8), and apron entrance point signs (paragraph 4.9).

Required Required

Non-movement area boundary marking (per paragraph 5.4). Required Required

All other markings not listed paragraph 1.4.1.1. Recommended

Note 1: Table 1-1 and Table 1-2 are interrelated. Surface markings per Table 1-2 that require black borders may initially be deferred for the case of new, dark-colored asphalt concrete/new asphalt treated pavement surfaces for up to 2 years as per Table 1-1. This case applies to dark, newly constructed asphalt concrete/newly asphalt treated pavements. New light-colored asphalt projects require the black borders upon completion. Note 2: Surface markings identified per Note 1 that sufficiently fade before 2 years, shall receive black borders.

Technique 2 – Use of Glass Beads on Permanent Pavement Markings. Glass beads identified in Item P-620 of AC 150/5370-10 are an effective means of enhancing the conspicuity of surface markings when aircraft and vehicles operate at night, during low-visibility conditions, or when the pavement surface is wet. The glass beads used in the below applications should meet the specifications found in AC 150/5370-10, Item P-620. If Type IV glass beads that have a larger diameter are used, then they should only be applied in higher-built materials, such as TT-P-1952E-Type III waterborne paint, epoxy, methyl methylacrylate, or preformed thermoplastic. The beads used in the intermix and on the surface of preformed thermoplastic should meet the specifications found in AC 150/5370-10, Item P-620.

Precaution: Glass beads should never be used in black paint, including numerals and inscriptions found in Appendix B. See Table 1-2 for surface markings that are required or recommended to have glass beads.

Chapter 1. › 1.5 No-Taxi Islands.

Glass Bead Requirement Per AC 150/5370-10, Paragraph 620-3.5, Application

(General)

Glass beads shall be distributed upon the marked areas at the locations shown on the plans to receive glass beads immediately after application of the paint. A dispenser shall be furnished that is properly designed for attachment to the marking machine and suitable for dispensing glass beads. Glass beads shall be applied at the rate(s) shown in Item P-620, Table 1 of AC 150/5370-10. Glass beads shall not be applied to black paint or green paint, including numerals and inscriptions found in Appendix B. Type I beads must be used in the red or pink background paint on surface painted holding position sign (SPHPS) and geographic position marking (GPM). Using Type III beads washes out the background color, resulting in less contrast between the inscription and background. Glass beads shall adhere to the cured paint or all marking operations shall cease until corrections are made. Different bead types shall not be mixed, with the exception of those supplied on the surface of preformed thermoplastic (to comply with the bead gradation chart found in AC 150/5370-10, Item P-620). Regular monitoring of glass bead embedment should be performed.

No-Taxi Islands.

Safety Enhancements. For this advisory circular, the term “no-taxi island” is a category of island having safety enhancements. The safety enhancements mentioned by this paragraph are found along a section of a taxiway. The safety enhancements are achieved by painting specific surface markings and, depending on the taxiway’s location, complying with standard taxiway design features under AC 150/5300-13, complying with standard vertical signage under AC 150/5340-18, and complying with standard taxiway edge lighting under AC 150/5340-30, Design and Installation Details for Airport Visual Aids. The following applications of no-taxi islands serve to mitigate taxiway excursions, runway incursions, or certain types of wrong runway takeoffs. Explanations of the most common applications are listed below along with subparagraph 1.5.2 which provides sequential practices for applying surface markings, types of physical reconstruction of a taxiway section, and figures for visual clarification of their applications.

1.5.1.1 Case 1: This application involves taxiway excursions into unpaved areas or onto a paved area not intended for aircraft operations. Documented examples are (a) compound taxiing turns along consecutive taxiwaytaxiway intersections as shown in Figure 1-6 and (b) an extra-long section of a taxiway that borders a large paved area(s). The objective for this application is to provide clearer, visual cues along such sections of a taxiway so that pilots can recognize the edges of usable full-strength taxiway from non-maneuvering areas. Under this application the safety

enhancement is generally achieved through surface painted markings alone.

1.5.1.2 Case 2: This application involves runway incursions caused by terminals or aprons whose taxiways offer direct access to a runway; in some cases pilots have more immediate access to the runway. The most common documented examples are illustrated in Figure 1-7 (runway lacks a fulllength parallel taxiway), and Figure 4-3 of AC 150/5300-13, (runway has a full-length parallel taxiway). In both cases, a taxi route beyond the apron offers direct taxi access to a runway. The objective for this application is to create turning maneuvers for pilots along a reconfigured taxi route while on the apron or just beyond the apron prior to entering the runway. Under this application the safety enhancement is achieved by either (1) creating no-taxi islands on aprons which are generally accomplished through surface painted marking(s), namely, continuous taxiway edge markings, taxiway shoulder markings, and greenish no-taxi island(s), and possibly installing vertical signage or (2) removing/ reconfiguring/ constructing a taxiway beyond the apron.

1.5.1.3 Case 3: This application involves runway incursions and certain types of wrong-runway takeoffs caused by an oversized entrance taxiway. A documented example is a single entrance taxiway with excessive width located on a sizable paved area that abuts the runway entrance as shown in Figure 1-8 (figure shows new taxiway fillet design methodology from AC 150/5300-13). The objective for this application is to downsize this oversized entrance taxiway to the standard taxiway width plus having specific taxiway surface marking(s) and relocation of vertical signage closer to the taxiway centerline. Excess pavement usually provides enough surface area to obtain the standard taxiway shoulder width. This action enhances the recognition of the location of the runway holding position by creating a more distinguishable, channeled entrance to the assigned runway. Regarding wrong-runway takeoffs, this application may mitigate wrong runway takeoffs when an excessively wide taxiway entrance serves two runway ends that are in very close proximity to each other. Under these applications the safety enhancement is achieved by creating greenish no-taxi islands (a design standard for entrance taxiways) after downsizing excessive taxiway width and by the relocation of standard surface painted markings and placement of vertical signage. Physical reconstruction of the entrance taxiway or the removal of excessive pavement may not be necessary. Making changes, in this case, may also require changes to runway/taxiway lights and airfield guidance signs.

1.5.1.4 Case 4: This application involves runway incursions caused by certain multi-entrance taxiways located on a single, expansive paved area that abuts the runway; usually located at the runway end. A documented example is an excessive paved area with multi-parallel entrance taxiways that lack greenish no-taxi islands as shown in Figure 1-9 (figure shows

new taxiway fillet design methodology from AC 150/5300-13). As illustrated in the “before” example, the continuous pavement lacks (1) standard entrance taxiway widths, (2) greenish no-taxi islands (a design standard for entrance taxiways), (3) standard vertical signage for each taxiway entrance, and (4) standard dual-continuous taxiway edge surface markings on both sides of each taxiway entrance. The objective for this application is to obtain standard width entrance taxiways by the insertion of greenish no-taxi islands which in turn, allow each reconfigured entrance taxiway to have its own, unique taxiway identifier, surface markings, and vertical signage; thus creating a unique tunnel effect. This action enhances the recognition of each runway holding position and allows for the proper placement of their vertical signage and other surface markings. Under this application the safety enhancement is achieved by creating no-taxi islands through the placement of standard surface painted markings and standard vertical signage with or without the physical reconstruction of the entrance taxiway(s).

Sequential Process for Safety Enhancements. The following descriptions provide sequential practices for applying surface markings and provide illustrations to achieve the applications explained in subparagraph 1.5.1.

1.5.2.1 Case 1A. Taxiway section has stabilized/paved taxiway shoulders with or without paved areas beyond the taxiway shoulders, see Figure 1-6.

1. First, paint the dual-continuous taxiway edge marking per paragraph 4.4 of this advisory circular.

2. If excursions continue, then paint yellow taxiway shoulder markings according to paragraph 4.10.4 of this advisory circular.

Figure 1-6: picture of page 32Figure 1-6 · page 32
Picture of the page from the copy saved here

3. If excursions persist, then, for the taxiway section suffering continued excursions, apply a green border that starts beyond the end point of the yellow taxiway shoulder markings to create a visually green no-taxi island(s). The depth of the green no-taxi island must be at least equal to the width of standard taxiway shoulder for the largest taxiway design group using this taxiway. This action may require adding stabilized pavement. If pavement exists, apply green paint in accordance to Federal Standard 595, Color Number #34108. For locations lacking paved areas beyond the taxiway shoulder(s), the green border may be achieved by planting grass, installing green artificial turf, or, for desert locations, placement of an earthen material that provides a more definitive, visual distinction between the shoulders and the ground areas. Note: Because of the variability in the shape of existing taxiway geometries, these sequential marking steps may not be fully achieved. For example, there is insufficient area between the non-parallel taxiways to obtain the standard width of a green border beyond the end point of standard taxiway shoulder

markings. Common examples are taxiways in such close proximity to each other that they create small unusable odd-shape/circular areas. In such situations, two acceptable options are to (1) paint yellow taxiway shoulder markings with a green border onto the available taxiway shoulder(s) such that all or some of the green border is painted between the yellow taxiway shoulder markings or (2) simply paint the available shoulder green without the yellow taxiway shoulder markings. For severe situations, the depth of the green border should, to the extent possible, equal the width of the standard yellow taxiway shoulder markings for the largest taxiway design group using the site.

1.5.2.2 Case 1B. Taxiway section lacks stabilized/paved taxiway shoulders, see Figure 1-6.

1. First paint the dual- continuous taxiway edge marking per paragraph 4.4 of this advisory circular.

2. If excursions continue, then plant grass or install green artificial turf beyond the edges of the taxiway for a distance equal to at least the width of standard taxiway shoulder for the largest taxiway design group using this taxiway.

3. If excursions persist, then construct a stabilized/paved standard taxiway shoulder width per AC 150/5300-13 that is painted with yellow taxiway shoulder markings per paragraph 4.10.4 of this advisory circular, plus create (with or without stabilized pavement) the green border per Case1A (3).

1.5.2.3 Case 2A. Aprons with a taxiway having direct access to a runway which lacks a parallel taxiway, see Figure 1-7.

Figure 1-7: picture of page 33Figure 1-7 · page 33
Picture of the page from the copy saved here

1. First, reconfigure taxiway route(s) located on the apron to create a notaxi island in front of the existing taxiway serving the runway. This action produces multiple turning operations for pilots. In some cases, such as aprons that lack sufficient space to create the no-taxi island affect, construct a taxiway(s) off the sides of the apron running parallel to the runway to create the desired turning maneuver for pilots. The geometry of the taxiways created by the marking of the no-taxi islands must be designed following the criteria of AC 150/5300-13.

2. For no-taxi islands located on the apron, paint the dual-continuous taxiway edge marking per paragraph 4.4.

3. If runway incursions continue or taxing through the no-taxi island occurs, then paint yellow taxiway shoulder markings according to paragraph 4.10.4.

4. If runway incursions or taxing through the no-taxi island persist, then apply a green border starting from the end point of yellow taxiway

shoulder markings to create a visually green no-taxi island(s). The depth of the green no-taxi island must be at least equal to the width of standard taxiway shoulder for the largest taxiway design group using this taxiway. The border is green paint per Federal Standard 595, Color Number #34108.

5. For both subparagraphs 3 and 4 above, install any required or deemed necessary vertical taxiway signage in accordance with AC 150/5340- 18 and,

6. Paint any required or deemed necessary surface markings per this advisory circular.

1.5.2.4 Case 2B. Aprons with direct access taxiways to runways that have a parallel taxiway, see Figure 4-2 of AC 150/5300-13A.

1. As illustrated in Figure 4-3 of AC 150/5300-13A, relocate the existing taxiway between the apron and the parallel taxiway to a new location. This action produces the multiple turning operations for pilots prior to entering the runway. The geometry of the new location taxiways must be designed following the criteria of AC 150/5300-13.

2. Install required or deemed necessary surface markings and vertical signage for the new taxiway connector.

3. Paint the abandoned taxiway to produce a green no-taxi island or remove the abandon taxiway pavement.

4. Install taxiway edge lights or reflectors in accordance with AC 150/5340-30. Vertical taxiway edge reflectors or lights will enhance the identification of islands to pilots during nighttime, low visibility and during snow conditions when markings are not clearly visible.

1.5.2.5 Case 3. Single Entrance Taxiways with Excessive-Width, Figure 1-8.

1. Reduce the excessive width of the entrance taxiway by painting dualcontinuous taxiway edge markings (paragraph 4.4) that indicate the edges of the prescribed standard taxiway width per AC 150/5300-13 for the largest taxiway design group using the taxiway entrance; plus

2. Convert excessive pavement into, if possible, standard taxiway shoulder widths having painted standard yellow taxiway shoulder markings per paragraph 4.10.4 of this advisory circular; plus

Figure 1-8: picture of page 34Figure 1-8 · page 34
Picture of the page from the copy saved here

3. Create green no-taxi islands for the reconfigured entrance taxiway starting from the end of the end point of the yellow taxiway shoulder marking. The depth of the green border must be at least equal to the width of the standard taxiway shoulder required for the largest taxiway

design group using the taxiway entrance. The border is green paint per Federal Standard 595, Color Number #34108; plus

4. Relocate/install all missing vertical signage in accordance with AC 150/5340-18. Install taxiway edge lights or reflectors in accordance with AC 150/5340-30. Vertical taxiway edge reflectors or lights will enhance the identification of islands to pilots during nighttime, low visibility and during snow conditions when markings are not clearly visible.

1.5.2.6 Case 4. Multi-Entrance Taxiways located on single, expansive pavement abutting the runway, see Figure 1-9.

1. If the width of any entrance taxiway exceeds the standard taxiway width, then follow instructions in Case 3.

2. If none of the entrance taxiways exceed the standard width, then paint standard yellow taxiway shoulder markings per paragraph 4.10.4 of this advisory circular; plus

3. Create green no-taxi islands for each taxiway entrance starting from the end of the yellow taxiway shoulder markings. The depth of the green border must be at least equal to the width of the standard taxiway shoulder required for the largest taxiway design group using the taxiway entrance. The border is green paint per Federal Standard 595, Color Number #34108; plus

4. Relocate/install all missing vertical signage for each entrance taxiway in accordance with AC 150/5340-18. Install taxiway edge lights or reflectors in accordance with AC 150/5340-30. Vertical taxiway edge reflectors or lights will enhance the identification of islands to pilots during nighttime, low visibility and during snow conditions when markings are not clearly visible.

Figure 1-6. Case 1

A. ADD DUAL CONTINUOUS TAXIWAY EDGE MARKINGS

B. ADD TAXIWAY SHOULDER MARKINGS

C. ADD GREEN BORDER BEYOND

TAXIWAY SHOULDER MARKINGS

Figure 1-7. Case 2

Apron

Apron

New taxiways (3)

New islands (3)

New non-movement area boundary marking

After

Runway "9-27" vertical holding position sign (opposite)

Runway "9" vertical holding position sign (opposite)

Runway "9-27" vertical holding position sign (opposite)

Runway "9-27" vertical holding position sign (opposite)

Runway "9" vertical holding position sign (opposite)

Runway "9-27" vertical holding position sign (opposite)

Before

Figure 1-8. Case 3

Notes: Airport operator has the option to remove all excess pavement.

New green “No Taxi Island” if not all excessive pavement was removed.

New edge of taxiway

per AC 150/5300-13

TRANSITION

or existing pavement

Existing pavement to

Existing taxiway centerline,

remain and used as a

for new taxiway geometry

per AC 150/5300-13

SPHS and edge markings,

to be relocated to match

new taxiway geometry

Marked as unusable to be removed

RWY "9" Vertical holding

BEFORE

New green "no taxi" island

New taxiway shoulder marking (typ)

position sign

RWY "9" vertical holding

position sign RWY "9" Vertical holding position sign to be removed or relocated

RWY "9" Vertical holding

position sign

RWY "9" Vertical holding

position sign

AFTER

Dual-continuous taxiway edge surface marking (typ)

No yellow taxiway shoulder markings and a greenish "no taxi island" is painted when all excessive pavement is removed.

shoulder/no-taxi island

Figure 1-9. Case 4

TRANSITION

or marked as unusable

Existing pavement to remain

Existing taxiway centerline

and used as a shoulder/no-taxi

island for new taxiway geometry per AC 150/5300-13

to be relocated to match

taxiway geometry

Existing pavement to be removed

BEFORE

New green "no taxi" island

New taxiway shoulder marking (typ)

RWY "9" vertical holding

position sign

AFTER Dual-continuous taxiway edge

surface marking (typ)

RWY "9" Vertical holding

position sign

RWY "9" Vertical holding position sign

New edge of taxiway

per AC 150/5300-13

RWY "9" Vertical holding

position sign RWY "9" vertical holding position sign to be removed or relocated

Existing taxiway centerline, SPHS and edge markings, to be relocated to match new taxiway geometry

New RWY "9-27" vertical

holding position sign

Page Intentionally Blank

Figure 1-9: picture of page 35Figure 1-9 · page 35
Picture of the page from the copy saved here

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.1 Application.

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS

Application. The minimum requirements for surface marking schemes used for runways are a direct function of the approach category for each runway threshold and the existence of displaced thresholds, stopways, blast pads, or extra-wide shoulders. Runways having the same approach category off both runway thresholds will show the same surface marking scheme from threshold to threshold (with some exceptions, such as the runway designator). In comparison, runways with different approach categories will show two different surface marking schemes. The complete runway surface marking schemes required by a runway combine Table 2-1 requirements with the physical structure, such as blast pads or stopways, and usage of the runway.

Table 2-1 identifies the minimum standard surface marking schemes for paved runways

based upon the approach category. Figure A-1, Figure A-2, Figure A-3, and Figure A-6 provide the dimensional standards for the surface marking schemes. An airport operator may paint a runway with additional surface marking schemes beyond those required, such as a visual runway with runway edge markings or the aiming point marking, if deemed necessary by the FAA. Furthermore, surface markings beyond those described in Table 2-1 are required to support particular operations, such as a displaced threshold, or to identify runway related features, such as blast pads, stopways, or Engineered Materials Arresting Systems (EMAS).

Table 2-1. Minimum Required Runway Surface Marking Schemes for Paved Runways

Threshold Approach Category

Runway Surface Marking

Scheme

Visual Approach

Non-precision

Approach

(and approaches with vertical

guidance not lower than ¾ -

statute mile visibility)

Precision Approach

(Approaches with lower

than ¾ -statute mile

visibility)

Landing Designator (par. 2.3) X X X

Centerline (par. 2.4) X X X

Threshold Markings (par. 2.5) Note 1 X X

Aiming Point (par. 2.6) Note 2 Note 3 X

Touchdown Zone (par. 2.7) X

Edge Markings (par. 2.8) Note 4 Note 4 X

Note 1: Required on runways serving approach categories C and D airplanes and for runways used, or intended to

be used, by international commercial air transport. Note 2: Required on 4,200-foot (1,280 m) or longer runways serving approach categories C and D airplanes.

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.2 Interruption of Runway Surface Markings.

Note 3: Required on 4,200-foot (1,280 m) or longer instrumented runways. Note 4: Used when the full runway pavement width may not be available for use as a runway.

Runways with a displaced threshold, blast pad, stopway, or extra-wide shoulders require

additional marking schemes not identified in Table 2-1. These surface marking schemes and others not in Table 2-1 are discussed separately in this AC. See AC 150/5300-13 for detailed information about the location of displaced thresholds, blast pads, and stopways.

Painting Note No. 1

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

The dimensional size for the runway surface marking promulgated by this AC is based on the assumption that the runway has a standard runway width as prescribed by AC 150/5300-13. For convenience, the standard widths are shown in Table 2-2. below.

Airport operators with non-standard runway widths may, for specified surface markings, proportionally adjust the marking’s width to be less than the standard scheme. Under non-standard conditions, the width of marking is in direct proportion to the available runway width. However, the corresponding length for the marking is never reduced.

Subsequent paragraphs in this AC will specify, via a green-shaded solution box, those runway surface markings that may be proportioned. The absence of a greenshaded solution box in a subsequent paragraph implies that that runway surface marking, such as the runway centerline, is not to be decreased in width even if other nearby runway surface markings are proportionally adjusted.

Interruption of Runway Surface Markings. At the intersection of two runways, the surface markings of one runway are, with the possible exception of runway edge markings (such as V-shaped runways), fully displayed through the intersection while the surface markings of the other runway are completely interrupted. This process of removing runway surface markings from one runway establishes an order of precedence among the different runways.

Order of Precedence.

2.2.1.1 The order of precedence for displaying the runway surface marking schemes of one runway over the other runway at the intersection of these runways should follow this order:

1. Precision approach runway, Category III.

2. Precision approach runway, Category II.

3. Precision approach runway, Category I.

4. Non-precision approach runway.

5. Visual runway.

2.2.1.2 For an intersection of runways of the same precedence, the preferred higher precedence runway is the one having the lowest approach minima or the runway end most often used.

Lesser Precedence Runways. The manner in which a lesser precedence runway intersects a higher precedence runway may require the shifting or complete removal of certain surface markings that fall within the intersection. As shown in Figure A-5, the most affected surface markings are the runway centerline, runway edge markings, aiming point markings, and runway touchdown zone markings. The latter two runway markings may have implications when shifted or removed. See paragraphs 2.2.3 and 2.6 for shifting an aiming point marking, and see paragraph 2.7 for removing touchdown zone markings.

Consequences When Shifting the Aiming Point Markings. Figure A-4 shows one possible conflict that could occur when the aiming point markings are relocated.

2.2.3.1 When the aiming point markings of a given runway that are in the intersection of two runways need to be moved more than 200 feet (61 m) away from the existing threshold, the airport operator will have to displace the existing threshold or designate a new runway end (threshold) in order to retain the distance between the threshold and the aiming point marking as illustrated in the bottom illustration of Figure A-4. The preferred distance to be maintained between the newly designated threshold and the shifted aiming point marking is 1,020 feet (311 m); see paragraph 2.6.

2.2.3.2 Runways with an approach landing aid, such as Precision Approach Path Indicators (PAPIs) or Visual Approach Slope Indicators (VASIs), which are co-located with the aiming point markings, can be negatively affected when an excessive shifting of the aiming point marking occurs. The consequence could be a non-compatible threshold crossing height for landing airplanes. When the aiming point markings are shifted more than 60 feet (18.3 m), the co-located PAPI or VASI should be evaluated for relocation to provide a correct vertical guidance to pilots. See AC 150/5340-30 to determine if the impact of shifted aiming point markings warrants a relocation of the co-located PAPI or other runway approach aids. Contact FAA Air Traffic Organization (ATO) Technical Operations regarding Federal PAPIs and VASIs.

2.2.3.3 For landing safety, the FAA requires that whenever the distance between the threshold and aiming point markings is 1,220 feet (372 m) or more, the airport operators place a note in the Chart Supplement to inform pilots

about the increased distance existing between the threshold and the aiming point markings.

V-Shaped Runway Ends Configuration. The V-shaped runway ends configuration is a pavement geometry where two runway ends commence from the same location but proceed in different directions (see Figure 1-2). This undesirable geometry requires a special shifting procedure of the runway landing designator marking of the lesser precedence runway farther down the runway than prescribed by paragraph 2.3. The special procedure is as follows. On the lesser order runway, locate the point on its runway centerline that is perpendicular to the inside common corner of the two intersecting runways. Once this base point is located, move this base point 20 feet (6.5 m) down the runway centerline to relocate the bottom of the letter or number(s) used for the runway landing designator. For an intersection of runways of the same precedence, the preferred higher precedence runway is the one having the lowest approach minimums or the runway end most often used.

Figure 2-1. V Geometry

Figure 2-1: picture of page 40Figure 2-1 · page 40
Picture of the page from the copy saved here

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.3 Runway Landing Designator Marking.

Safety Notice No. 2

Wrong-Runway Takeoffs Mitigation

In an effort to eliminate the possibility of a “wrong-runway” takeoff operation by pilots, the airport operator should reconstruct V-shaped runway geometries to a different geometry, possibly an X-shaped geometry.

Runway Landing Designator Marking.

Purpose. The runway landing designator marking identifies a runway end.

Requirement. See Table 2-1.

Location. Runway landing designator marking(s) must be located from the runway threshold per Figure A-1, Figure A-2, Figure A-3, or from the displaced threshold per Figure A-7. All these figures show the start location for both types of thresholds.

Color. Runway landing designator markings are white. See paragraph 1.4 and Table 1-1 for required techniques to enhance this marking.

Characteristics.

1. A runway landing designator marking consists of a number comprising one or two digits. When parallel runways exist, the number is further supplemented with a letter.

2. A single-digit runway landing designation number is never preceded by a zero. Runway landing designators are centered in accordance with the green box entitled “Centering of Runway Landing Designators - Width of Rectangular Boxes.”

3. For single runways, dual parallel runways, and triple parallel runways, the designator number is the whole number nearest the one-tenth of the magnetic azimuth along the runway centerline when viewed from the direction of approach. For example, where the magnetic azimuth along the runway centerline is 183 degrees, the runway designator marking would be 18; for a magnetic azimuth of 87 degrees, the runway designation marking would be 9. For a magnetic azimuth ending in the number “5” such as 185 degrees, the runway designator marking may be either 18 or 19.

4. On four or more parallel runways, one set of adjacent runways is numbered to the nearest one-tenth of the magnetic azimuth and the other set of adjacent runways is numbered to the next nearest one-tenth of the magnetic azimuth.

5. For parallel runways, each runway landing designator number must be supplemented by a letter, in the order shown from left to right when viewed from the direction of approach as prescribed by the following marking criteria. Different labeling patterns than those prescribed below are permissible under certain circumstances as identified in subparagraph 6 below.

a. Two parallel runways having a magnetic azimuth of 182 degrees are designated

“18L” and “18R.”

b. Three parallel runways having a magnetic azimuth of 87 degrees are designated

“9L,” “9C,” and “9R.”

c. Four parallel runways having a magnetic azimuth of 324 degrees are designated

“32L,” “32R,” “33L,” and “33R.”

d. Five parallel runways having a magnetic azimuth of 138 degrees are designated

“13L,” “13R,” “14L,” “14C,” and “14R” or “14L,” “14R,” “13L,” “13C,” and “13R.” Other combinations exist for this case. See subparagraph 6 below.

e. Six parallel runways having a magnetic azimuth of 83 degrees are designated

“8L,” “8C,” “8R,” “9L,” “9C,” and “9R. See subparagraph 6 below.

f. Seven parallel runways having a magnetic azimuth of 85 degrees – the runways would be designated “8L,” “8C,” “8R,” “9L,” “9C,” “9R,” and “10.” Other combinations exist for this case. See subparagraph 6 below.

6. There are certain runway placements where the surface marking schemes for parallel runways provided in subparagraph 5 above may not be appropriate because their orientation may lead to pilot confusion. For example, the marking scheme recommended for parallel runways on the same side of a terminal is to follow subparagraph 5 above . However, when two parallel runways are separated by a large distance, as by a central terminal or several terminals, it is preferable to designate the runways as non-parallel runways to avoid pilot confusion. Another case that may cause pilot confusion is a turf runway that is parallel to a paved visual runway but at a great distance from a higher precedence paved runway. In general, the airport operator should carefully choose how to mark parallel runways to eliminate pilot confusion.

The appearance of the letters and numbers used for runway landing designator markings

are in the form and proportion shown in Figure A-6. The spacing between numbers and letters are as shown in Figure A-1, Figure A-2, Figure A-3, and Figure A-6. However, with the exception of the numerals 6 and 9, all numerals and the letters L, C, and R are 60 feet (18.3 m) in height. Numerals 6 and 9, which are 63 feet (18.9 m) in height, follow the Rule of 69. That is, although the numerals 6 and 9 are taller, the 3-foot tips of the numerals are ignored so that their separations from the threshold markings, the letters L-C-R, the first runway centerline, and the start of the runway threshold remain as shown in Figure A-1, Figure A-2, and Figure A-3.

Painting Note No. 2

Centering of Runway Landing Designators

Width of Rectangular Boxes

Runway landing designators are centered along the runway centerline in accordance with the width of the numeral(s) and the width of the letter.

An imaginary rectangular box contains the numeric runway landing designator whose height equals tallest numeral and whose width equals either (1) the width of a single numeral or (2) the total width of two numerals plus the required spacing between the numerals. A runway that requires the letters L, C, or R, will create a second rectangular box in the same fashion. See Figure A-6 for widths of numerals and letters and horizontal spacing between numerals. See Figure A-1, Figure A-2, and Figure A-3 for vertical spacing of rectangular boxes.

Example 1 - Runway 7R will consists of two rectangular boxes. The width of the rectangular box for the numeral 7 equals 23 feet (6.9 m) while the letter R has a width equal to 20 feet (6 m). Therefore, 23 feet (6.9 m) and 20 feet (6 m) are divided equally along the runway centerline.

Example 2 - Runway 14 will consist of a single rectangular box. Numeral 1 is 7 feet wide and numeral 4 is 25 feet wide, with a 15-foot space between them. The total width equals 47 feet (7 + 15 + 25) [14. 3 m (2.1 + 4.6 + 7.6)]. Therefore, 47 feet (14.3 m) is divided equally along the runway centerline.

Note: Although the majority of 2-digit designators are centered equally along the runway centerline, example 2 results in the numeral 4 overlapping the runway centerline (unpainted). Other similar combinations, such as Runway 13, Runway 18, place the wider numeral along the unpainted runway centerline.

Painting Note No. 3

Application of Proportioning Runway Markings for Airplane Design Group (ADG) I Runway Width

Due to the space limitations on very narrow runways, the size and spacing of the numbers and letters are reduced only when necessary such that the painted runway landing designator is no closer than 2 feet (0.6 m) from the runway edge or runway edge markings. For example, this problem may occur when painting certain dualnumbered runway landing designators spaced 15 feet (4.5 m) apart on an ADG I runway width of 60 feet (18.3 m). In such cases, first reduce the 15-foot (4.5-m) spacing to 10 feet (3.1 m) and retain the size of numerals and letter per Figure A-6. Second, reduce the 15-foot (4.5-m) spacing to 10 feet (3.1 m) and reduce the size of numerals and letter proportionally to maintain the 2-foot (0.6-m) edge or runway edge markings clearance.

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.5 Runway Threshold Marking.

Runway Centerline Marking.

Purpose. The runway centerline marking identifies the physical center of the runway width and provides alignment guidance to pilots during takeoff and landing operations. For lighting provisions, see AC 150/5340-30.

Requirement. See Table 2-1.

Location. A runway centerline marking is located along the physical center of the runway width and spaced between the runway landing designation markings as shown in Figure A-1, Figure A-2, and Figure A-3.

Color. The runway centerline marking is white. See paragraph 1.1 and Table 1-1 for required techniques to enhance this marking.

Characteristics. A runway centerline marking consists of a line of uniformly spaced stripes and gaps and of uniform width.

1. The stripes are 120 feet (36.5 m) in length and the gaps are 80 feet (24.3 m) in length.

2. The minimum width of the stripes is:

a. 36 inches (90 cm) for precision runways.

b. 18 inches (45 cm) for non-precision runways.

c. 12 inches (30 cm) for visual runways.

3. To accommodate varying runway lengths, all adjustments to the uniform pattern of runway centerline stripes and gaps are made near the runway midpoint (defined as the distance between the two thresholds or displaced thresholds). Under such cases, reduce the lengths of both the stripes and gaps starting from midpoint and proceed toward the runway thresholds. Reduced stripes must be at least 80 feet (24 m) in length, and the reduced gaps must be at least 40 feet (12.3 m) in length. The affected stripes and gaps within the section should show a uniform pattern.

Runway Threshold Marking.

Purpose. A runway threshold marking, commencing 20 feet (6 m) from the actual start point of runway threshold, closely identifies the actual beginning point of the runway threshold used for landings. For lighting provisions, see AC 150/5340-30.

Requirement. See Table 2-1.

Location. The runway threshold marking starts 20 feet (6 m) from the actual start point of the runway threshold as shown in Figure A-1 and Figure A-2. This value remains the same even though a 10-foot (3-m) white threshold bar is introduced, such as for displaced thresholds or the addition of a blast pad or stopway, as shown in Figure A-9. Previously, when a displaced threshold was painted or a blast pad or stopway added, the 20-foot (6m) dimension was increased to 30 feet (9 m) to accommodate the requirement for painting the runway threshold bar. When any runway threshold or displaced threshold is re-marked with threshold bar markings, or when a blast pad or stopway is added, the separation is 10 feet (3 m) as shown in Figure A-8.

Color. The components of a runway threshold marking are white. See paragraph 1.4 and Table 1-1 for required techniques to enhance this marking.

Characteristics. The runway threshold marking consists of a pattern of longitudinal stripes of uniform dimensions spaced symmetrically about the runway centerline. The number of longitudinal stripes and their spacing is determined by the runway width.

1. Table 2-2 provides the number of longitudinal stripes for runways having standard runway widths as defined by AC 150/5300-13. Figure A-1 illustrates the pattern for a 150-foot (45-m) wide runway. See paragraph 2.5.5 for painting guidance applicable to non-standard runway widths.

Table 2-2. Number of Runway Threshold Stripes for Standard Runway Widths

Standard runway widths Number of symmetrical stripes

60 feet (18.3 m) 4

75 feet (22.9 m) 6

100 feet (30.5 m) 8

150 feet (45.7 m) 12

200 feet (61 m) 16

2. For standard runway widths, the longitudinal stripes are 150 feet (45.7 m) long and 5.75 feet (1.75 m) wide with the outer edges spaced (stripe-gap) 5.75 feet (1.75 m) apart. However, the two longitudinal stripes nearest the runway centerline are doubled spaced, i.e., outer edges of the near-most pair are 11.5 feet (3.5 m) apart. Figure A-1 illustrates the stripe-gap pattern for 150-foot (46-m) wide runways. The

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.6 Runway Aiming Point Marking.

stripe-gap pattern allows sufficient room to paint runway edge markings without interfering with the outermost longitudinal stripes.

Painting Note No. 4

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

For standard 75-foot (23-m) wide runways that use 36-inch (90-cm) wide runway edge markings, the stripe-gap pattern of 5.75 feet (1.75 m) is reduced to 5.50 feet (1.68 m).

3. For non-standard runway widths, the same stripe-gap pattern is continued from the runway centerline until the outermost longitudinal stripe is not closer than 4 feet (1.2 m) from the runway edge. For example, for a non-standard 125-foot (38-m) wide runway, the stripe-gap pattern yields a total of 10 longitudinal stripes symmetrical about the runway centerline. In no case should the stripe-gap pattern exceed 92 feet (27 m) on either side of the runway centerline. The value of 92 feet (27 m) is the width for the pattern used on the standard 200-foot (61-m) wide runways.

4. When there is pavement in excess of 5 feet (1.5 m) prior to the actual start of the runway threshold and (a) pilots may confuse the pavement as part of the actual runway or (b) the pavement does not have the same load bearing capacity as the runway, then painting of a runway threshold bar per paragraph 2.9 is required. In contrast, if the installation of landing threshold lights requires pavement to support the light fixtures and the supportive pavement abuts the start point of the runway threshold, then the supportive pavement is not considered a part of the runway. In this instance, the painting of a runway threshold bar is not required.

Runway Aiming Point Marking.

Purpose. A runway aiming point marking provides a visual aiming point for landing operations.

Requirement. See Table 2-1.

Location. The preferred beginning of the aiming point marking starts 1,020 feet (311 m) from the runway threshold as shown in Figure A-1, Figure A-2, and Figure A-3. However, this preferred separation is not adequate for all cases as partially discussed below.

Note: The term “preferred” assumes the following conditions: standard visual glide slope of 3 degrees; no obstacle in the approach area affecting the obstacle clearance surface of

the PAPI; standard threshold crossing heights per AC 150/5340-30; sufficient runway length so not to force the placement of the aiming point marking; no rapid terrain drop off near the approach threshold that encounters severe turbulence; no elevation differences between the threshold and the installation zone of the PAPI.

2.6.3.1 Intersecting Runways. A separation tolerance of plus or minus 200 feet (61 m) is allowed when it is necessary to shift the aiming point marking to avoid overlapping aiming point markings at dual runway intersection as shown in Figure A-4 and Figure A-5, and discussed in paragraph 2.2.3. However, depending on the threshold crossing heights and the available runway approach aids, the shifting of the aiming point markings may negatively impact the threshold crossing heights for approaching airplanes. One potential impact of the shift is to the co-located runway approach aids, such as the PAPI, in which the previous vertical guidance offered by the aiming point marking to pilots is now incompatible with the threshold crossing height associated with the runway approach aid. Under such conditions, adjustment in the location of the affected runway approach aid may be necessary after an evaluation so that the co-located relationship between the PAPI (and other approach aids) and the shifted aiming point marking permits an acceptable landing operation for both landing aids.

2.6.3.2 Compatible Threshold Crossing Heights. See AC 150/5340-30 to determine if the impact of a relocated aiming point marking warrants relocating the co-located PAPI (or other runway approach aids).

Color. The runway aiming point marking is white. See paragraph 1.4 and Table 1-1 for required techniques to enhance this marking.

Characteristics.

1. The runway aiming point marking consists of two conspicuous rectangular markings, 150 feet (45.7 m) in length for runways of at least 4,200 feet (1280 m) in length between the thresholds (or a displaced threshold(s)), and 100 feet (30.5 m) in length for lesser lengths between the thresholds (or a displaced threshold(s)). The runway aiming point marking is located symmetrically on each side of the runway centerline as shown in Figure A-1, Figure A-2, and Figure A-3. See Table 2-2. for the dimensions of standard runway widths per AC 150/5300-13.

2. The width of each rectangular marking is as follows:

a. 30 feet (9.1 m) for standard runway widths of 150 feet (45.7 m) or greater.

b. 20 feet (6 m) for standard runway widths of 100 feet (30.5 m).

c. 15 feet (5 m) for standard runway widths of 75 feet (22.9 m).

d. 12 feet (3.7 m) for a standard runway width of 60 feet (18.3 m).

3. The lateral spacing between the inner sides of the runway aiming point markings is as follows:

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.7 Runway Touchdown Zone Marking.

a. For runways of 150 feet (45.7 m) or more in width, the lateral spacing between

the inner sides of the rectangular bars centered on the runway centerline is 72 feet (21.9 m).

b. For runways of 100 feet (30.5 m) in width, the lateral spacing between the inner

sides of the rectangular bars centered on the runway centerline is 48 feet (14.6 m).

c. For runways of 75 feet (22.9 m) in width, the lateral spacing between the inner

sides of the rectangular bars centered on the runway centerline is 36 feet (11.0 m).

d. For runways of 60 feet (18.3 m) in width, the lateral spacing between the inner

sides of the rectangular bars centered on the runway centerline is 28.8 feet (8.8 m).

Painting Note No. 5

Application of Proportioning Runway Markings

for Non-Standard Runway Widths and for Standard Runway Widths less than 150 feet (45.7 m)

For runways with widths below 150 feet (45.7 m), the width of the rectangular bars and their lateral spacing between the inner sides of the rectangular bars are adjusted in proportion to the available runway width by using the 150-foot (45.7-m) width runway parameters to determine the percentage decrease in lateral spacing and width of each marking. For example, a non-standard 70-foot wide runway would apply 70/150 = 0.467 to obtain a lateral spacing of 72 × 0.467 = 33.6 feet (10.25 m) between the pair and an individual width of 30 × 0.467 = 14 feet (4.27 m).

If runway edge markings are also painted, which are not reduced, then the adjustment should add the width of the corresponding runway edge markings plus a minimum 1-foot (0.3-m) clearance between the outer edge of the aiming point marking and the runway edge marking.

Lateral spacing – in no case is the lateral spacing less than 30 feet (9.1 m) except for runways less than 75 feet (22.9 m).

Lengths – in all cases, the length of the aiming point marking remains unchanged.

Runway Touchdown Zone Marking.

Purpose. For landing operations, the touchdown zone marking identifies the touchdown zone along a precision runway in 500-foot (152-m) increments. For lighting provisions, see AC 150/5340-30.

Requirement. See Table 2-1.

Location. The touchdown zone marking consists of symmetrically arranged pairs of rectangular bars in groups of one, two, and three along the runway centerline as shown in Figure A- 1. As shown, there are five groupings with the aiming point marking serving as an independent, sixth pair.

2.7.3.1 The touchdown zone marking scheme maintains a 900-foot (275-m) “no-marking zone” from the midpoint of the runway back toward the threshold. That is, those pairs of surface markings that extend within 900 feet (275 m) of the runway midpoint are eliminated. The intent of this painting practice is to preserve a 1,800-foot (550-m) unmarked area so pilots do not confuse the surface markings during a landing with the surface markings for the other approach procedure. The same practice applies equally to a displaced threshold, i.e., the midpoint is located between the thresholds or displaced thresholds and not the runway ends. Taking this into consideration, the painted pattern for the runway touchdown zone marking depends on the (a) authorized approach off each runway and (b) the available length between the runway thresholds or displaced threshold, i.e., the midpoint. The surface marking patterns for the two possible cases are provided in Table 2-3 (case #1) and Table 2-4 (case #2).

2.7.3.1.1 Case #1 – Only one runway end requires the runway touchdown zone marking scheme. Apply Table 2-3 criteria, which take into account the “no-marking zone” of 900 feet (275 m) from the midpoint back toward the threshold.

Table 2-3. Groupings of Touchdown Zone Markings Required When Installed From One

Threshold

Distance Between Thresholds

(or displaced thresholds)

Markings for Precision Approach

End (includes displaced

threshold)

Other Runway End

Visual or Non-precision

6,065 ft (1849 m) or greater1 Full set of markings Aiming point marking

5,565 ft (1697 m) to 6,064 ft (1848 m) Less one grouping of rectangular

bar markings2

Aiming point marking

5,065 ft (1544 m) to 5,564 ft (1696 m) Less two groupings of rectangular bar markings

Aiming point marking

4,565 ft (1391 m) to 5,064 ft (1543 m) Less three groupings of rectangular bar markings

Aiming point marking

Distance Between Thresholds

(or displaced thresholds)

Markings for Precision Approach

End (includes displaced

threshold)

Other Runway End

Visual or Non-precision

Note 1: The value of 6,065 feet is derived as follows. For the non-precision or visual runway end, the table assumes the 900-foot “no-marking zone” criterion plus the length of a preferred aiming point marking, which starts 1,020 feet from the start of the threshold to obtain a length of 1,920 feet. Add to this the length of the aiming point marking. Per paragraph 2.6.5, the length of the aiming point marking is either 150 feet or 100 feet. This table uses a length of 150 feet because all the entries in column #1 are greater than 4,200 feet. Therefore, adding 150 feet to 1,920 feet obtains a length of 2,070 feet. For the precision end, which equals 3,995 feet, it assumes the 900-foot “no-marking zone” followed by the standard 75-foot-long rectangular bar for a total length of 975 feet. Add to this value the full 3,000-foot touchdown zone marking scheme and the 20-foot separation between the actual starting point of the runway threshold (or displaced threshold) and the bottom edge of threshold marking to obtain 3,995 feet. Summing the values 3,995 and 2,070 yields 6,065 feet.

Note 2: Each reduction in a pair of rectangular bar markings from the precision end equates to a 500-foot (152-m) reduction between the thresholds.

The painting rationale for this table is to ignore the midpoint between the thresholds so the precision instrumented landing is favored over non-precision or visual landings. That is, the length of the non-precision/visual side of the runways always remains at 2,070 feet in length to promote the painting of a full set of touchdown zone markings.

2.7.3.1.2 Case #2 – Both runway ends require runway touchdown zone markings. Apply Table 2-4 criteria, which take into account the “no-marking zones” of 1,800 feet (550 m) from the threshold-to-threshold midpoint.

Table 2-4. Groupings of Touchdown Zone Markings Required When Installed From Both

Thresholds

Distance Between Thresholds

(or displaced thresholds)

Markings for Each Threshold

(or displaced threshold)

7,990 ft (2436 m) or greater1 Full set of markings

6,990 ft (2130 m) to 7,989 ft (2435 m) Less one grouping of rectangular bars from each

side nearest to the runway midpoint2

5,990 ft (1826 m) to 6,989 ft (2129 m) Less two groupings of rectangular bars from

each side nearest to the runway midpoint2

4,990 ft (1521 m) to 5,989 ft (1825 m) Less three groupings of rectangular bars from

each side nearest to the runway midpoint2

Note 1: The value of 7,990 feet is derived as follows. Proceed from the runway midpoint in one direction, and you will have the 900-foot “no-marking zone” criterion followed by the standard 75-foot long rectangular bar for a total length of 975 feet. Add to this value the full 3,000-foot touchdown zone marking scheme plus the 20-foot separation between the actual starting point of the runway threshold (or displaced threshold) and the edge of threshold marking to obtain 3,995 feet. Double this value for both directions to obtain 7,990 feet.

Note 2: Each reduction in a grouping of rectangular bar markings from both sides equates to a 1,000-foot (305-m) reduction between the thresholds.

Distance Between Thresholds

(or displaced thresholds)

Markings for Each Threshold

(or displaced threshold)

The painting rationale for this table is to preserve the midpoint between the thresholds, thereby promoting an equal treatment of painting groupings of rectangular bar markings for both sides.

2.7.3.2 Because the location of the aiming point marking may be adjusted from the threshold to accommodate different approach slopes and/or heights over the threshold, and to possibly take into account non-zero runway gradients, the location of an adjusted aiming point marking will vary. Please see AC 150/5340-30. Under such conditions, an adjusted aiming point will, in most cases, continue to be located between the first and the second touchdown zone markings. However, when the accumulative effect of the adjustments is severe (defined as when a touchdown zone marking coincides with or is within 160 feet (48.8 m) of the adjusted aiming point marking), that touchdown zone marking must not be painted. For the pilot community, this practice permits the aiming point marking to retain its prominent visual landing aid as compared to a touchdown zone marking.

Color. All rectangular bars are white. See paragraph 1.4 and Table 1-1 for required techniques to enhance this marking.

Characteristics.

1. For runway widths of 150 feet (45.7 m) or greater, each rectangular bar is 75 feet (22.9 m) long and 6 feet (1.8 m) wide. The lateral spacing between the inner sides of the rectangular bars on the same side of the runway centerline is 5 feet (1.5 m).

2. For runway widths less than 150 feet (45.7 m), the length of the marking remains unchanged, but the width and the lateral spacing between the markings are reduced proportionally to the decrease in runway width by using 150-foot (45.7 m) parameters to determine the percentage decrease.

3. The lateral spacing between the inner sides of the rectangular bars centered along the runway centerline is equal to that of the aiming point marking (criteria repeated below from paragraph 2.6.5). In all cases, the length of the rectangular bars (and the aiming point markings) remains unchanged. See Table 2-2 for the dimensions of standard runway widths.

a. For runways of 150 feet (45.7 m) or more in width, the lateral spacing between

the inner sides of the rectangular bars centered on the runway centerline is 72 feet (21.6 m).

b. For runways of 100 feet (30.5 m) in width, the lateral spacing between the inner

sides of the rectangular bars centered on the runway centerline is 48 feet (14.6 m).

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.8 Runway Edge Marking.

c. For runways of 75 feet (22.9 m) in width, the lateral spacing between the inner

sides of the rectangular bars centered on the runway centerline is 36 feet (11.0 m).

d. For runways of 60 feet (18.3 m) in width, the lateral spacing between the inner

sides of the rectangular bars centered on the runway centerline is 28.8 feet (8.8 m).

Painting Note No. 6

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

For runways with widths below 150 feet (45.7 m), the width of the rectangular bars and their lateral spacing between the inner sides of the rectangular bars are adjusted in proportion to the available runway width by using the 150-foot (45.7 m) width runway parameters to determine the percentage decrease in lateral spacing and width of the marking. For example, a nonstandard 70-foot wide runway would apply 70/150 = 0.467 to obtain a lateral spacing for the centered pair of 72 × 0.467 = 33.6 feet (10.25 m), a lateral spacing for other pairs of 5 × 0.467 = 2.3 feet (0.7 m), and a width of 6 feet × 0.467 = 2.8 feet (0.85 m). This adjustment must be such that the inner sides of the innermost rectangular bars to the runway centerline align themselves with the inner side of the aiming point marking. Given that the runway edge markings are painted, the adjustment should be such that the clearance between the runway side strip and the outer edge of the three-bar grouping is a minimum of 1-foot (0.3-m). In no case should the three-bar group be painted farther out from the runway centerline than the aiming point marking.

Runway Edge Marking.

Purpose. The runway edge marking provides enhanced visual contrast between the runway edge and the surrounding terrain or runway shoulders, and delineates the width of suitable paved area for runway operations. For lighting provisions, see AC 150/5340-30.

Requirement. See Table 2-1.

Location. The runway edge marking consists of two parallel stripes, one placed along each edge of the usable runway with the outer edge of each stripe approximately on the edge of the paved useable runway. For extra wide runways, such as military runways converted for public use, the maximum distance between the outer edges of the parallel stripes is 200 feet (61 m). Figure A-1 illustrates the runway edge marking.

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.9 Runway Threshold Bar Marking and Runway Displaced Threshold Marking.

Color. The stripes of the runway edge marking are white. See paragraph 1.4 for recommended techniques to enhance this marking.

Characteristics. The runway edge marking has a minimum width of 36 inches (90 cm) for runways of 100 feet (30.5 m) or wider in width and at least 18 inches (45 cm) on smaller width runways (see Table 2-2. for standard runway widths). The runway edge marking extends the full length of the runway as shown in Figure A-7, except for precision runways as shown in Figure A-1 which lack a threshold bar marking.

1. For runways with a displaced threshold, the edge markings continue through the paved area prior to the displaced threshold as shown Figure A-7. This continuation of the edge markings is required because this paved area is used for takeoffs and for landing rollouts from the other direction.

2. Where an aligned taxiway, as shown in Figure A-8 and Figure A-10, precedes a runway threshold, both edge markings will terminate. The point of termination of the edge markings is determined by the taxiway geometry. Prohibited: The conversion of a runway section into an aligned taxiway or the construction of a new aligned taxiway is prohibited. See AC 150/5300-13. The FAA further recommends that existing aligned taxiways, for example, as shown in Figure A-8 and Figure A- 10, be removed or be reconfigured into usable runways as shown in Figure A-7 or Figure A-11. When a taxiway connects to a runway or the runway has turn pads or turnarounds, the runway edge marking remains continuous between the runway and these adjoining infrastructures.

3. For intersecting runways, see guidance in paragraph 2.2.

Runway Threshold Bar Marking and Runway Displaced Threshold Marking. The complete marking scheme for a runway with a displaced threshold, when required by AC 150/5300-13, includes a runway threshold bar and arrowheads with and without arrow shafts. Figure A-7, Figure A-10, and Figure A-11 illustrate the various applications of displaced thresholds and the requirement for additional marking components. For lighting provisions, see AC 150/5340-30.

Runway Threshold Bar Marking.

2.9.1.1 Purpose. The runway threshold bar marking serves two functions by delineating the start of the (i) displaced threshold by indicating the beginning section of the runway available for landing from the unusable section on the approach side of the displaced threshold as shown in Figure A-7, Figure A-10, and Figure A-11 and (ii) regular threshold from prepared surfaces before the runway that are used for a blast pad, stopway, EMAS or end of an aligned taxiway as shown in Figure A-8 and Figure A-9.

2.9.1.2 Requirement. Install a runway threshold bar marking when there is a displaced threshold, blast pad, stopway, EMAS, or aligned taxiway on the approach side of the threshold.

2.9.1.3 Location. The runway threshold bar marking is an elongated rectangular bar that is located perpendicular to the runway centerline and on the landing portion of the runway. The outboard edge of the marking is aligned with the location labeled “start of runway displaced threshold” as shown in Figure A-10 or “start of runway threshold” as shown in Figure A-9. Note that the entire runway threshold bar marking is on the portion of the runway available for landing.

2.9.1.4 Color. The runway threshold bar marking is white. See paragraph 1.4 for required techniques to enhance this marking.

2.9.1.5 Characteristics. The runway threshold bar marking is 10 feet (3.1 m) in width and extends between the runway edges or between the runway edge markings.

Arrow Marking. The arrow marking (arrowheads with and without arrow shafts; depending on the length of the displacement) performs three possible functions, that is, two cases for displaced thresholds and one case for a runway threshold with an aligned taxiway.

2.9.2.1 Purposes.

1. Figure A-7 illustrates the predominant case in which the threshold is displaced from the runway end. In this case, white arrowheads with and without arrow shafts are required to identify the portion of the runway before the displaced threshold to provide centerline guidance for pilots during approaches, takeoffs, and landing rollouts from the opposite direction.

2. Figure A-10 illustrates the rare case in which a displaced threshold is preceded by an aligned taxiway. In this case white arrowheads with and without arrow shafts and yellow arrowheads without arrow shafts are required to identify the runway portion from the aligned taxiway portion. Furthermore, a yellow runway demarcation bar is required to identify the start of the runway. See paragraph 2.9.3 for runway demarcation bar criteria and figures.

3. Figure A-8 illustrates the rare case in which a runway threshold (not displaced) is preceded by an aligned taxiway. In this case, yellow arrowheads without arrow shafts are required to identify the runway portion from the aligned taxiway portion.

General Comment

The conversion of a runway section into an aligned taxiway or the construction of a new aligned taxiway is prohibited. See AC 150/5300-13.

2.9.2.2 Requirement. Install this marking when the threshold is displaced or preceded by an aligned taxiway.

2.9.2.3 Locations.

1. For the predominant case, arrowheads with or without arrow shafts (depending on the length of displacement) are located on the portion of the runway before the displaced threshold.

2. For the rare cases referenced in paragraph 2.9.2.1, only arrowheads are used on the portion of the aligned taxiway before the threshold bar marking or before the demarcation bar marking as described in paragraph 2.9.3.

2.9.2.4 Colors.

1. For the predominant case, the arrow shaft and arrowhead are white. See paragraph 1.4 for required techniques to enhance these markings which are part of a displaced threshold.

2. For the rare cases referenced in paragraph 2.9.2.1, the arrowhead is yellow which is not part of a displaced threshold.

2.9.2.5 Characteristics. The dimensions and spacing requirements for arrow shafts and arrowheads are as shown in Figure A-7 (function one, as listed in paragraph 2.9.2.1), Figure A-8 (function two), and Figure A-10 (function three).

Runway Demarcation Bar Marking.

2.9.3.1 Purpose. A demarcation bar delineates a runway with a displaced threshold from a blast pad, stopway, or an aligned taxiway that precedes the runway.

2.9.3.2 Requirement. Install a demarcation bar marking only when the threshold is displaced and the runway is preceded by a blast pad, stopway, or aligned taxiway.

2.9.3.3 Location. The demarcation bar is an elongated rectangular bar on a blast pad, stopway, or an aligned taxiway that is perpendicular to the runway

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.10 Chevron Markings for Blast Pads, Stopways, and EMAS.

centerline at the point of intersection with the start of the runway as shown in Figure A-10 and Figure A-11. As shown in Figure A-10, the portion of aligned taxiway before the demarcation bar is not part of the usable runway for takeoff or for landing from the opposite direction. Note that no part of the demarcation bar is on the unable runway for takeoff or for landing.

2.9.3.4 Color. The demarcation bar marking is yellow. See paragraph 1.4 for recommended techniques to enhance this marking.

2.9.3.5 Characteristics. The demarcation bar marking is 3 feet (0.9 m) wide and extends across the entire width of the blast pad, stopway, or aligned taxiway.

Chevron Markings for Blast Pads, Stopways, and EMAS.

Purposes. The chevron marking identifies paved blast pads, stopways, and EMAS (engineered materials arresting systems) in relation to the end of the runway. For lighting provisions, see AC 150/5340-30, and for EMAS design, see AC 150/5220-22, Engineered Materials Arresting Systems (EMAS) for Aircraft Overruns.

Requirement. Install chevron markings on blast pads, stopways, and EMAS.

Location. The chevron marking is located on the blast pad and stopway that are aligned with and contiguous to the runway end as shown in Figure A-9 and Figure A-11. The chevron scheme for an EMAS installation is also centered along the extended runway centerline (not shown in Figure A-9 and Figure A-11).

Color. Chevron markings are yellow. See paragraph 1.4 for a recommended technique to enhance this marking.

Characteristics. Dimensionally, stopways equal the width of the runway while blast pads equal the runway width plus the standard shoulder widths (see AC 150/5300-13). The dimensions and spacing requirements for chevron markings are shown in Figure A-9. The recommended minimum length for a stopway is 150 feet (45.7 m) to allow for at least two chevron stripes. For cases where (1) standard length blast pads, per AC 150/5300- 13, are installed off runway ends designed exclusively for small airplanes (Airplane Design Groups I and II– small) or (2) existing stopways are less than 150 feet (45.7 m) in length on runway widths of 75 feet (22.9 m) or less, the width of the chevrons and the

Chapter 2. SURFACE MARKINGS FOR RUNWAYS › 2.11 Runway Shoulder Marking.

spacing between the chevrons shown in Figure A-9 can be reduced by two-thirds. The intent of the reduction in dimensions is to provide pilots with at least two visible chevrons.

Runway Shoulder Marking.

Purpose. The runway shoulder marking is used, when needed, as a supplement to further delineate a paved runway shoulder that pilots have mistaken or are likely to mistake as usable runway. This marking is used only in conjunction with the runway edge marking.

Requirement. Runway shoulder markings are optional.

Location. The runway shoulder marking is located between the runway edge marking and the outer edge of the paved shoulder as shown in Figure A-12.

Color. Runway shoulder markings are yellow. See paragraph 1.4 for a recommended technique to enhance this marking.

Characteristics. The runway shoulder marking consists of stripes 3 feet (0.9 m) in width and spaced 100 feet (30.5 m) apart along the edge of the runway. The stripes start at the runway midpoint, are slanted at an angle of 45 degrees to the runway centerline, and are oriented as shown in Figure A-12.

Page Intentionally Blank

CHAPTER 3. HOLDING POSITION MARKINGS

Applications of Holding Position Markings. The purposes for the different holding position markings are to prevent aircraft and vehicles from entering into protected areas associated with a runway and navigational aids, or to control traffic at the intersection of taxiways. This AC describes six operational situations (cases) using three different holding position marking schemes. Cases 1, 2, and 3 employ the same marking scheme referred to as Pattern A – runway holding position marking. Cases 4 and 5 employ a different marking scheme referred to as Pattern B – ILS, POFZ holding position marking or the Runway Approach/Departure Areas of a runway. For certain POFZ operational situations, Case 5 uses Pattern B in which it usually appears as an L-shaped ladder. Case 6 uses a different marking scheme referred to as Pattern C – intermediate holding position marking for taxiway/taxiway intersections. Figure A-13 and Figure A-14 show the four different marking patterns and Figure 3 of AC 150/5340-18G shows the application for the Runway Approach/Departure Areas of a runway.

Chapter 3. HOLDING POSITION MARKINGS › 3.2 Case 1 and Case 2 – Applications of Pattern A for the Runway…

• Case 1: In terms of taxiing on a runway, an aircraft will need to hold short of an intersecting runway (see paragraph 3.2).

• Case 2: In terms of landing on a runway used for land and hold short operations (LAHSO), the aircraft will need to hold short of an intersecting runway or, in some rare cases, at a specified hold spot on the landing runway (see paragraph 3.2).

• Case 3 (most common application for Cases 1, 2, and 3): In terms of taxiing on a taxiway, an aircraft will need to hold short prior to entering an active runway (see paragraph 3.3).

• Case 4: In terms of taxiing on a taxiway, an aircraft will need to hold short before entering the protected area of an Instrument Landing System (ILS) (see paragraph 3.4).

• Case 5: In terms of taxiing on a taxiway, an aircraft will need to hold short before entering the protected area of a Precision Obstacle Free Zone (POFZ) or Runway Approach/Departure Areas of a runway (see paragraph 3.5). Although the surface marking pattern is the same as Case 4, the pattern in many POFZ applications is Lshaped instead of only linear in shape.

• Case 6: In terms of taxiing on a taxiway, an aircraft will need to hold short of a taxiway/taxiway intersection (see paragraph 3.6).

Case 1 and Case 2 – Applications of Pattern A for the Runway Holding Position Marking on Runways.

Purpose. Pattern A, when painted on a runway as shown in Figure A-13, identifies the location where a pilot (or vehicle driver) is to stop and hold when (1) the runway is operationally closed for an interval of time so that ATCT can control taxiing operations through a

runway/runway intersection or (2) the runway is used for land and hold short operations (LAHSO). For necessary corresponding signage and lighting provisions, see AC 150/5340-18, and AC 150/5340-30.

Safety Notice No. 3

Safety Initiatives

Note 1: Land and hold short operations (LAHSO) require a letter of agreement between the airport operator and the airport traffic control tower (ATCT).

Note 2: Since the design standard for a full-length parallel taxiway reduces both wrong-runway takeoffs and runway incursions, we do not recommend the use of an operationally closed runway as a taxiway, especially when a parallel taxiway exists. Such an operation can potentially confuse pilots because this taxiing operation introduces yellow-colored taxiway surface markings onto the runway itself. Hence, to avoid the potential for operational errors by pilots, the airport operator should take measures to meet the full-length parallel taxiway design standard. In some cases, the operational capacity for a given runway could indicate the need for dual parallel taxiways to avoid this type of taxiing operation.

Note 3: To avoid a runway incursion event at runway/runway intersections when an operationally closed runway is used as a taxiway, the intersection must have the runway holding position marking and corresponding signs whether or not pilots taxi through the runway/runway intersection. Additionally, this marking should only be used in those instances where documentation supports the need for the operational use of the runway as a taxiway. The operational use of a runway as a taxiway must be described in a Letter of Agreement with the ATCT.

Location. In all Case 1 and Case 2 applications, the criteria given below assume that the centerlines of the intersecting runways are perpendicular. Hence, for runway/runway intersections that are non-perpendicular, additional distance may be required to ensure that all airplane features, such as wingtips, remain outside the protected area of the intersecting runway.

3.2.2.1 Operationally Closed Runways Used for Taxiing Operations. The location of the runway holding position marking on operationally closed runway is in accordance with the holding position criteria per AC 150/5300-13 for the intersecting runway’s runway design code.

3.2.2.2 Runways Used for LAHSO.

3.2.2.2.1 The location of the runway holding position marking on the runway used for LAHSO is in accordance with the holding position criteria per AC 150/5300-13 for the intersecting runway’s runway design code. On rare

cases the location of the runway holding position marking for LAHSO is based on a predetermined hold-short point along the landing runway to protect an approach/departure flight path or to overcome painting difficulties as described below in paragraph 3.2.2.2.2. In no case should the location of the predetermined hold-short point be within the holding position criteria per AC 150/5300-13 for the intersecting runway’s runway design code.

3.2.2.2.2 Certain airfield geometries for runways that are used for taxiing or LAHSO operations have intersecting taxiway(s) that hamper the painting of the runway holding position marking (and installation of accompanying necessary signage) in accordance with the applicable holding position criterion. One such geometry occurs when a crossing taxiway or its fillet intersects the runway where the marking or sign is to be placed. One solution is to move the hold-short point farther away from the runway/runway intersection so that both the marking and the installed signage clear the common crossing area. Under this solution:

1. the marking is always painted at a greater distance than the holding position criteria in AC 150/5300-13, and

2. the required corresponding signage retains only the runway designations, i.e., never uses a taxiway designation.

Color. The Pattern A marking scheme, as shown in Figure A-13, is yellow and, when painted on light-colored pavements, is outlined in black. See paragraph 1.4 and Table 1-1 for required techniques to enhance this surface marking on light-colored pavements.

Characteristics.

3.2.4.1 The marking is identical to the runway holding position marking installed on a taxiway as described in paragraph 3.3 and shown in Figure A-13. The solid lines, as compared to the dashed lines, are always on the side where the aircraft is to hold.

3.2.4.2 The marking is installed perpendicular to the runway centerline and interrupts all runway markings except for the runway designation marking. If the runway holding position marking should interrupt the mentioned exceptions, then paint the runway holding position marking farther away than specified by AC 150/5300-13 to avoid any interruption of these specified markings. The painting practice is to avoid “over striping” existing runway surface markings.

3.2.4.3 The runway holding position marking extends across the full width of the runway but not onto the runway shoulders or onto any intersecting taxiway fillet.

Case 3 – Applications of Pattern A for the runway Holding Position Marking on Taxiways.

Purposes. Pattern A, when painted on a taxiway as shown in Figure A-13, serves several roles. For a taxiway that intersects a runway at an airport with an operating airport traffic control tower (ATCT), the Pattern A marking scheme identifies the location on a taxiway where pilots and vehicle drivers are to stop until they receive a clearance from ATCT to proceed onto the runway. Under this role, Pattern A may be supplemented with the Geographic Position Marking as part of the airport’s LVO/SMGCS Plan as described in paragraph 4.11 and as shown in Figure A-24. For a taxiway that intersects a runway at an airport without an operating airport traffic control tower, Pattern A identifies the location where pilots and vehicle drivers are to stop to ensure that they have adequate separation with other aircraft before proceeding onto the runway. If the marking is located closer than prescribed by AC 150/5300-13, such as when the taxiing aircraft penetrates a Terminal Instrument Procedures (TERPS) surface, then the airport operator can expect higher approach minimums to the impacted runway end. AC 150/5300-13 includes a discussion of these airspace surfaces. Except as specified in paragraph 3.2, the runway holding position marking must not be used for any other situations than the roles described in this paragraph. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

Continue reading ↓ 120 of 279 passages shown