AC 150/5340-30J Design and Installation Details for Airport Visual Aids
This AC provides guidance and recommendations on the installation of airport visual aids. See the Principal Changes paragraph for a list of major changes to the document since the last version.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Design and Installation Details for Airport Visual Aids
Date: 2/12/2018 Initiated by: AAS-100
AC No.: 150/5340-30J Change:
1 Purpose. This advisory circular (AC) provides guidance and recommendations on the installation of airport visual aids.
2 Cancellation. This AC cancels AC 150/5340-30H, Design and Installation Details for Airport Visual Aids, dated July 21, 2014.
3 Application. The Federal Aviation Administration (FAA) recommends the guidance and specifications in this AC for Design and Installation Details for Airport Visual Aids. In general, use of this AC is not mandatory. However, use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) or with revenue from the Passenger Facility Charges (PFC) Program. See Grant Assistance No. 34, Policies, Standards, and Specifications, and PFC Assurance No. 9, Standards and Specifications. All lighting configurations contained in this standard are a means acceptable to the Administrator to meet the lighting requirements of Title 14 Code of Federal Regulations (CFR) Part 139, Certification of Airports, Section 139.311, Marking, Signs and Lighting. See exception in paragraph 2.3.1.2.
4 Principal Changes. Revision J of this AC incorporates the following principal changes:
1. Paragraph 1.6 is added to prohibit non-certified devices from attachment to the high voltage series power circuit.
2. Paragraph 2.3.2.2.2 added runway edge light spacing tolerance for displaced thresholds.
3. Paragraph 2.5.3.2.3 provided “Categorization of General Aviation Airports” to better define “Non-Part 139 Airports” for Figure A-116.
ii
4. Paragraph 2.5 incorporated Engineering Brief (EB) #92A, Light Spacing Guidance for New Taxiway Fillet Geometry. It provides new guidance for taxiway edge lighting design for new taxiway construction or rehabilitation.
5. Paragraph 2.5.3.2.9 changed the reference for “Taxiway End Indicators” to “Taxiway Curve Indicators” to differentiate from “Taxiway End Markers”.
6. Paragraph 4.8.8.2.1 provided clarification regarding the use of yellow/red runway guard light (RGL)/Stop bar light usage.
7. Paragraph 6.6.3.2 added wind cone “constant brightness” requirement and referenced AC 150/5370-10, Standards for Specifying Construction of Airports, for wind cones.
8. Paragraph 6.7.2.5 deleted the note about separate power sources for wind cone obstruction lights.
9. Paragraph 7.3.1.4.6 added reference to Federal Aviation Administration Technical Center (FAATC) report DOT/ FAA /AR-01/111, Temporary Installation Methods for PAPI/A-PAPI Systems.
10. Paragraph 7.4.2 is updated to move installation-specific information for Runway End Identifier Lights (REIL) to paragraph 7.7.5.
11. Paragraph 7.5.4.4.5 adds a note to explain what flight inspection personnel consider when evaluating the PAPI Obstacle Clearance Surface (OCS) and objects that are outside the surface. The reader is directed to paragraph 7.7.6.6.4 item 3 for additional information.
12. Paragraph 7.7.6.6.4 item 6 is updated to explain obstacles outside the PAPI OCS that may be evaluated during flight inspections.
13. Paragraph 8.1.3.2.4 item 2 adds a reference to AC 150/5345-51, Specification for Discharge-Type Flashing Light Equipment.
14. Paragraph 9.6 is updated for propane fueled generators.
15. Paragraph 10.2 item 4 added a note to address bolt torque maintenance requirements for in-pavement light fixtures.
16. Paragraph 10.3 is updated to remove reference to the application of silicone rubber between spacers and extensions.
17. Paragraph 11.2.1.11 is updated to remove references to using silicone sealant between the light base upper flange and extensions.
18. Paragraph 12.5 incorporates a rewrite for Counterpoise Lightning Protection System to simplify equipotential and isolation methods for airfield lighting counterpoise installation.
19. Paragraph 12.13 incorporates vault recommendations per National Fire Protection Association (NFPA) National Electric Code (NEC) guidelines.
20. Paragraph 13.2.5 incorporates NEC recommendations regarding “Installation of Cables”.
iii
21. Figure A-2 through Figure A-23 are updated to new taxiway edge lighting geometry.
22. Figures 2, 3, 5-12, and 16-22 are moved to Appendix H as legacy figures for reference only, and are not for use in new design.
23. Figure A-2 through Figure A-11 are reoriented to promote ease of review.
24. Figure 4, Figure 13, Figure 14, and Figure 15 with an aligned taxiway are deleted.
25. Figure A-5, Figure A-7, Figure A-8, Figure A-9 and Figure A-11 have added notes and are updated to align outboard threshold lights with approach side edge of the runway threshold marking.
26. Figure A-12, “Lighting for Crossover Taxiway”, Figure A-13, “Lighting for Runway Entrance”, Figure A-14, “Lighting for Taxiway Intersection” and Figure A-21, “Lighting for Typical High-speed Exit Taxiway” are new figures per guidance in AC 150/5300-13, Airport Design.
27. Figure A-16 shows a new 120-degree turn for “Spacing of Lights on Curved Taxiway Edges” to compliment Figure A-17, “Taxiway Edge Lights for Standard Taxiway Turns”.
28. Figure A-24, Figure A-25, Figure A-63, Figure A-74, Figure A-76, Figure A-79, Figure A-86, Figure A-92, Figure A-109, Figure E-11, Figure E-20 and Figure E-26 provide various updates which include but are not limited to editorial, requirements and reference updates.
29. Figure A-44 is updated to show maximum distance in Detail A.
30. Figure A-45 is updated to make bi-color taxiway centerline light fixtures more recognizable.
31. Figure A-48 is updated to add Note 5 to reference FAA JO 6850.2, Visual Guidance Lighting Systems.
32. Figure A-74 is updated to show orange/white stripe tolerances for airport beacon tip-down pole.
33. Figure A-76 Note 1 clarifies the tolerance for supplemental wind cone to location 1,000 feet from the runway end (±500 feet).
34. Figure A-79 provides REIL installation reference point clarification to Notes 1 and 2 to match 50 foot REIL separation requirements from runways and taxiways per FAA JO 6850.2. Notes 5 and 6 are updated to correct errors. Note 7 provides clarification to REIL elevation tolerance.
35. Figure A-80 updates Omni-directional Approach Lighting System (ODALS) strobe light spacing tolerances.
36. Figure A-81 changed “4 Mile Radius” to “4 NM Radius” for PAPI OCS to comply with FAA JO 6850.2.
37. Figure A-93 is updated for REIL installation details.
John R. DermodyJohn R. Dermody
iv
38. Figure A-109 deleted Note 2 which excluded elevated edge light types L-861E, L- 861SE, L-862E and L-862 for consideration of adjustment for High Snowfall Areas.
39. Figure A-111 “Equipotential Counterpoise Installation Method” is added to illustrate equipotential methods for airfield lighting counterpoise installation.
40. Figure A-116 is added to show taxiway edge light configurations at General Aviation (GA) Airports. The reference paragraph 2.5.3.2.3 is also updated to reference link the new figure.
41. Figure E-26, added Note 2 to reference paragraph 2.5.3.3.1 for guidance regarding taxiway edge light fillet geometry.
42. Table 8-1, added Notes 1 and 2 to state “idle status” for lighting of Visual Glide Slope Indicators (VGSIs) without heaters.
43. The AC is updated to remove long paragraphs and divide them into smaller sections to facilitate easier reading and better comprehension of the subject matter.
44. The format of the document has been updated, and minor editorial changes have been made throughout.
Hyperlinks (allowing the reader to access documents located on the internet and to maneuver within this document) are provided throughout this document and are identified with underlined text. When navigating within this document, return to the previously viewed page by pressing the “ALT” and “ ←” keys simultaneously.
Figures in this document are representations and are not to scale.
5 Metrics. To promote an orderly transition to metric units, this AC contains both English and metric dimensions. The metric conversions may not be exact metric equivalents, and, until there is an official changeover to the metric system, the English dimensions will govern.
6 Feedback on This AC. If you have suggestions for improving this AC, you may use the Advisory Circular Feedback form at the end of this AC.
7 Copies of This AC. All ACs are available online at http://www.faa.gov/regulations_policies/advisory_circulars/.
Director of Airport Safety and Standards
CONTENTS
Number Page
v
Chapter 1 Introduction … 1-1
1.1. General … 1-1
1.2. Scope … 1-1
1.3. Safety … 1-1
1.4. Mixing of Light Source Technologies … 1-1
1.5. Airports Geographical Information System (GIS) Database … 1-2
1.6. High Voltage Series Circuit Power … 1-2
Chapter 2 Runway and Taxiway Edge Lighting Systems … 2-1
2.1. General … 2-1
2.2. Selection Criteria … 2-1
2.3. Runway Edge Light Configurations … 2-1
2.4. Stopway Edge Lights … 2-6
2.5. Taxiway Edge Lights … 2-6
2.6. System Design … 2-11
2.7. Equipment and Materials … 2-15
Chapter 3 Runway Centerline and Touchdown Lighting Systems … 3-1
3.1. Introduction … 3-1
3.2. Selection Criteria … 3-1
3.3. Configuration … 3-1
3.4. Design … 3-3
3.5. Equipment and Material … 3-5
Chapter 4 Taxiway Lighting Systems … 4-1
4.1. Introduction … 4-1
4.2. Implementation Criteria … 4-2
4.3. Taxiway Centerline … 4-3
4.4. Runway Guard Lights (RGLs) … 4-7
4.5. Runway Stop Bar … 4-11
4.6. Combination In-Pavement Stop Bar and RGLs … 4-13
4.7. Clearance Bar Configuration … 4-13
CONTENTS
Number Page
vi
4.8. Design … 4-15
4.9. Equipment and Material … 4-28
4.10. Installation … 4-29
Chapter 5 Land and Hold Short Lighting Systems … 5-1
5.1. Introduction … 5-1
5.2. Background … 5-1
5.3. Definitions … 5-1
5.4. Implementation Criteria … 5-1
5.5. Configuration … 5-1
5.6. Design … 5-2
5.7. Equipment and Material … 5-6
5.8. Installation … 5-7
Chapter 6 Airfield Miscellaneous Aids … 6-1
6.1. Airport Rotating Beacons … 6-1
6.2. System Design … 6-1
6.3. Installation … 6-3
6.4. Maintenance … 6-4
6.5. Beacon Towers … 6-4
6.6. Wind Cones … 6-7
6.7. Obstruction Lights … 6-9
6.8. Equipment and Materials … 6-11
Chapter 7 Economy Approach Aids … 7-1
7.1. Introduction … 7-1
7.2. Types of Economy Approach Lighting Aids … 7-1
7.3. Selection Considerations … 7-1
7.4. Configurations … 7-3
7.5. Design … 7-5
7.6. Equipment and Material … 7-18
7.7. Installation … 7-20
CONTENTS
Number Page
vii
Chapter 8 Radio Control Equipment … 8-1
8.1. Radio Control Equipment … 8-1
Chapter 9 Standby Power – Non-FAA … 9-1
9.1. Background … 9-1
9.2. Definitions … 9-1
9.3. FAA Policy … 9-1
9.4. Electrical Power Configurations … 9-2
9.5. Design … 9-3
9.6. Equipment and Material … 9-6
9.7. Installation … 9-9
9.8. Inspection … 9-10
9.9. Tests … 9-11
9.10. Maintenance … 9-11
9.11. Reducing Electrical Power Interruptions … 9-12
9.12. Engine Generator Equipment Performance Requirements … 9-12
Chapter 10 Pavement Types … 10-1
10.1. General … 10-1
10.2. New Pavement – Rigid (Concrete) … 10-1
10.3. New Pavement – Flexible (Bituminous) … 10-4
10.4. Overlay – Rigid … 10-6
10.5. Overlay – Flexible … 10-8
Chapter 11 Fixture Mounting Bases … 11-1
11.1. General … 11-1
11.2. L-868 Mounting Bases … 11-1
11.3. Direct-Mounted (Inset) Fixtures … 11-4
11.4. Field Adjustable L-868 Mounting Bases … 11-7
11.5. Installation … 11-8
Chapter 12 Equipment and Material … 12-1
12.1. General … 12-1
CONTENTS
Number Page
viii
12.2. Light Bases, Transformer Housings, and Junction Boxes … 12-1
12.3. Duct and Conduit … 12-1
12.4. Cable, Cable Connectors, Plugs, and Receptacles … 12-2
12.5. Counterpoise (Lightning Protection System) … 12-5
12.6. Light Fixture Bonding … 12-9
12.7. Concrete … 12-9
12.8. Steel Reinforcement … 12-10
12.9. Adhesive and Sealants … 12-10
12.10.Load-Bearing Lighting Fixtures … 12-10
12.11.Inspection … 12-12
12.12.Auxiliary Relays … 12-14
12.13.Vault … 12-14
12.14.Maintenance … 12-15
Chapter 13 Power Distribution and Control Systems … 13-1
13.1. Introduction … 13-1
13.2. Power Distribution … 13-1
Appendix A 103BFigures … A-1
Appendix B 104BAirport Technical Advisory … B-1
Appendix C 105BTerms and Acronyms … C-1
Appendix D 106B ibliography … D-1
Appendix E 107BTypical Installation Drawings for Airport Lighting Equipment … E-1
Appendix F 108BApplication Notes … F-1
Appendix G 109BRunway Status Light (RWSL) System … G-1
Appendix H 10BLegacy Figures … H-1
CONTENTS
Number Page
ix
FIGURES
Figure A-1. Legend and General Notes for Figures A-1 through A-23 … A-1
Figure A-2. Runway and Threshold Lighting Configuration (LIRL Runways and MIRL Visual
Runways) … A-2
Figure A-3. Runway and Threshold Lighting Configuration (HIRL Precision Instrument
Approach - Runway Centerline Not Shown for HIRL. Non-Precision Instrument Approach for MIRL) … A-3
Figure A-4. Runway with Blast Pad (No Traffic) … A-4
Figure A-5. Lighting for Runway with Displaced Threshold … A-5
Figure A-6. Normal Runway with Taxiway … A-6
Figure A-7. Lighting for Runway with Displaced Threshold … A-7
Figure A-8. Lighting for Runway with Displaced Threshold/Usable Pavement … A-8
Figure A-9. Lighting for Runway with Displaced Threshold Not Coinciding with Opposite
Runway End … A-9
Figure A-10. Lighting for Runway with Stopway … A-10
Figure A-11. Lighting for Runway with Displaced Threshold and Stopway … A-11
Figure A-12. Lighting for Crossover Taxiway … A-12
Figure A-13. Lighting for Typical Runway Entrance … A-13
Figure A-14. Lighting for Taxiway Intersection … A-14
Figure A-15. Typical Straight Taxiway Sections (Less Than 200 ft (61 m)) … A-15
Figure A-16. Spacing of Lights on Curved Taxiway Edges … A-16
Figure A-17. Taxiway Edge Lights for Standard Taxiway Turns … A-17
Figure A-18. Taxiway Edge Lights for Runway/Taxiway Intersection … A-18
Figure A-19. Typical Single Straight Taxiway Edges (200 feet or More (61 m)) … A-19
Figure A-20. Typical Single Straight Taxiway Edges (Less Than 200 ft (61 m)) … A-20
CONTENTS
Number Page
x
Figure A-21. Lighting for Typical High-Speed Exit Taxiway … A-21
Figure A-22. Typical Taxiway Edge Lighting for Portions of Runways Used as Taxiway (When
Taxiway Lights Are “ON”) … A-22
Figure A-23. Typical Edge Lighting for Portions of Runways Used as Taxiway (When Runway
Lights Are “ON”) … A-23
Figure A-24. Light Fixture Wiring … A-24
Figure A-25. Typical Wiring Diagram Utilizing L-828 Step-type Regulator with External
Remote Primary Oil Switch … A-25
Figure A-26. Typical Wiring Diagram Utilizing L-828 Step-type Regulator with Internal
Control Power and Primary Oil Switch … A-26
Figure A-27. Typical Basic 120-Volt AC Remote Control System … A-27
Figure A-28. Alternative 120-Volt AC Remote Control System … A-28
Figure A-29. Typical 120-Volt AC Remote Control System with L-847 Circuit Selector Switch
… A-29
Figure A-30. Typical 48 VDC Remote Control System with 5-Step Regulator and L-841 Relay
Panel … A-30
Figure A-31. Typical 48 VDC Remote Control System with 3-Step Regulator and L-841 Relay
Panel … A-31
Figure A-32. Curves for Estimating Loads in High Intensity Series Circuits … A-32
Figure A-33. Curves for Estimating Loads in Medium Intensity Series Circuits … A-33
Figure A-34. Runway Centerline Lighting Layout … A-34
Figure A-35. Touchdown Zone Lighting Layout … A-35
Figure A-36. Section Through Non-adjustable Base and Anchor, Base and Conduit System,
Rigid Pavement … A-36
Figure A-37. Section Through Non-adjustable Base and Anchor, Base and Conduit System,
Flexible Pavement … A-37
Figure A-38. Runway Centerline Light – Shallow Base and Conduit Installation … A-38
Figure A-39. Saw Kerf Wireway Details … A-39
CONTENTS
Number Page
xi
Figure A-40. Saw Kerf Orientation Details – R/W Centerline and Touchdown Zone (TDZ)
Lights … A-40
Figure A-41. Transformer Housing Installation Details Inset Type Lighting Fixtures … A-41
Figure A-42. Typical Equipment Layout, Inset Type Lighting Fixtures … A-42
Figure A-43. Junction Box for Inset Fixture Installation … A-43
Figure A-44. Typical Taxiway Centerline Lighting Configuration for Non-Standard Fillets
(Centerline light spacing for operations above 1,200 ft (365 m) RVR) … A-44
Figure A-45. Color-Coding of Exit Taxiway Centerline Lights … A-45
Figure A-46. Taxiway Centerline Lighting Configuration for Acute-Angled Exits … A-46
Figure A-47. Controlled Stop Bar Design and Operation – “GO” Configuration … A-47
Figure A-48. Typical Taxiway Centerline Lighting Configuration for Standard Fillets
(Centerline light spacing for operations above 1,200 ft (365 m) RVR) … A-48
Figure A-49. Taxiway Centerline Light Beam Orientation … A-49
Figure A-50. In-Pavement Runway Guard Light Configuration … A-50
Figure A-51. Elevated RGL and Stop Bar Configuration … A-51
Figure A-52. Typical Light Beam Orientation for In-Pavement RGLs and Stop Bars … A-52
Figure A-53. Clearance Bar Configuration at a Low Visibility Hold Point … A-53
Figure A-54. Curves for Estimating Primary Load for Taxiway Centerline Lighting Systems .. A-
54
Figure A-55. Typical Elevated RGL Installation Details … A-55
Figure A-56. Typical In-Pavement RGL External Wiring Diagram – Power Line Carrier
Communication, One Light Per Remote … A-56
Figure A-57. Typical In-Pavement RGL External Wiring Diagram – Power Line Carrier
Communication, Multiple Lights per Remote … A-57
Figure A-58. Typical In-Pavement RGL External Wiring Diagram – Dedicated Communication
Link … A-58
Figure A-59. In-Pavement RGL Alarm Signal Connection … A-59
CONTENTS
Number Page
xii
Figure A-60. Controlled Stop Bar Design and Operation – “STOP” Configuration … A-60
Figure A-61. Controlled Stop Bar Design and Operation – Intermediate Configuration … A-61
Figure A-62. Controlled Stop Bar Design and Operation – “STOP” Configuration for A/C 2 .. A-
62
Figure A-63. Typical Layout for Land and Hold Short Lights … A-63
Figure A-64. Typical Wireway Installation Details for Land and Hold Short Lights … A-64
Figure A-65. Sawing and Drilling Details for In-pavement Land and Hold Short Lights … A-65
Figure A-66. Typical Block Diagram for Land and Hold Short Lighting System … A-66
Figure A-67. Typical Curve for Determining Maximum Separation Between Vault and Control
Panel with 120-Volt AC Control … A-67
Figure A-68. Beacon Dimensions and Wiring Diagram … A-68
Figure A-69. Calculations for Determining Wire Size … A-69
Figure A-70. Typical Automatic Control … A-70
Figure A-71. 120-Volt AC and 48-Volt DC Remote Control … A-71
Figure A-72. Typical Structural Beacon Tower … A-72
Figure A-73. Typical Tubular Steel Beacon Tower … A-73
Figure A-74. Typical Airport Beacon Tip-Down Pole … A-74
Figure A-75. Typical Pre-Fabricated Beacon Tower Structure … A-75
Figure A-76. Typical Location of Supplemental Wind Cone … A-76
Figure A-77. Externally Lighted Wind Cone Assembly (Frangible) … A-77
Figure A-78. Typical Layout for MALSF … A-78
Figure A-79. Typical Layout for REIL … A-79
Figure A-80. Typical ODALS Layout … A-80
Figure A-81. PAPI Obstacle Clearance Surface … A-81
CONTENTS
Number Page
xiii
Figure A-82. PAPI Signal Presentation … A-82
Figure A-83. Correction for Runway Longitudinal Gradient … A-83
Figure A-84. General Wiring Diagram for MALSF with 120-Volt AC Remote Control … A-84
Figure A-85. Typical Wiring Diagram for MALSF Controlled from Runway Lighting Circuit A-
85
Figure A-86. Typical Field Wiring Circuits for MALSF … A-86
Figure A-87. Typical Installation Details for Frangible MALS Structures – 6-foot (1.8 m)
Maximum … A-87
Figure A-88. Typical Wiring for REIL Multiple Operation … A-88
Figure A-89. Typical Wiring for REIL Series Operation … A-89
Figure A-90. FAA L-880 Style B (Constant Current) System Wiring Diagram … A-90
Figure A-91. FAA L-880 Style A (Constant Voltage) System Wiring Diagram … A-91
Figure A-92. PAPI Light Housing Unit (LHU) Installation Detail … A-92
Figure A-93. Typical Installation Details for Runway End Identifier Lights (REILs) … A-93
Figure A-94. Configuration “A” Electrical Power … A-94
Figure A-95. Typical kVA Input Requirements … A-95
Figure A-96. Typical Wiring Diagram for Configuration “A” Electrical Power … A-96
Figure A-97. Typical Equipment Layout for Configuration “A” Electrical Power … A-97
Figure A-98. Configuration “B” Electrical Power … A-98
Figure A-99. Typical Wiring Diagram for Configuration “B” Electrical Power … A-99
Figure A-100. Typical Wiring Diagram for Configuration “C” Power … A-100
Figure A-101. Flexible Pavement or Overlay Installation … A-101
Figure A-102. Use of Alignment Jig, No Reference Edge Available, Non-adjustable Base and
Conduit System … A-102
CONTENTS
Number Page
xiv
Figure A-103. Use of Alignment Jig, Reference Edge Available, Non-adjustable Base and
Conduit System … A-103
Figure A-104. In-pavement Shallow Base Runway Edge End or Threshold Light … A-104
Figure A-105. In-pavement Shallow Base Runway Centerline or TDZ Light … A-105
Figure A-106. Sawing and Drilling Details for In-Pavement Taxiway Centerline Lights .... A-106
Figure A-107. Wiring Details for Direct- and Base-Mounted Taxiway Centerline Lights ... A-107
Figure A-108. Typical Transformer Housing and Conduit Installation Details for Taxiway
Centerline Lights … A-108
Figure A-109. Adjustment of Edge Light Elevation for High Snowfall Areas … A-109
Figure A-110. Cable and Duct Markers … A-110
Figure A-111. Equipotential Counterpoise Installation Method … A-111
Figure A-112. Isolation Counterpoise Installation Method … A-112
Figure A-113. Power and Control System Block Diagram … A-113
Figure A-114. Typical PLC Control System Block Diagram … A-114
Figure A-115. PC Control System Block Diagram … A-115
Figure A-116. Typical Spacing for GA Airport Edge Lights … A-116
Figure E-1. Typical Standard Details for Runway and Taxiway Edge Lights –High Intensity
Light – Non-adjustable Base-mounted … E-2
Figure E-2. Typical Standard Details for Runway and Taxiway Edge Lights –Medium / High
Intensity Light – Non-adjustable Base-mounted … E-3
Figure E-3. Typical Standard Details for Runway and Taxiway Edge Lights –Medium Intensity
Light – Stake-mounted … E-4
Figure E-4. Typical Counterpoise and Ground Rod Connections … E-5
Figure E-5. Identification (ID) Tag Detail … E-6
Figure E-6. Standard Details for Underground Cable Installation – Typical Multiple Bank
Layout … E-7
CONTENTS
Number Page
xv
Figure E-7. Standard Details for Underground Cable Installation – Type A … E-8
Figure E-8. Standard Details for Underground Cable Installation – Type B … E-9
Figure E-9. Standard Details for Underground Cable Installation – Type C … E-10
Figure E-10. Standard Details for Underground Cable Installation – Plowed Cable … E-11
Figure E-11. Standard Details for Underground Cable Installation – Plowed Cable … E-12
Figure E-12. Standard Details for Taxiway Hold and Guidance Sign – Sign – Single Pedestal .. E-
13
Figure E-13. Standard Details for Taxiway Hold and Guidance Sign – Sign – Multiple Pedestal
… E-14
Figure E-14. Standard Details for Taxiway Hold and Guidance Sign – Detail A … E-15
Figure E-15. Standard Details for Pivoting Rotating Beacon Pole – Rotating Beacon and
Mounting Bracket Detail … E-16
Figure E-16. Standard Details for Pivoting Rotating Beacon Pole – Locking Device Detail .. E-17
Figure E-17. Standard Details for Pivoting Rotating Beacon Pole – Pivot Detail … E-18
Figure E-18. Standard Details for Pivoting Rotating Beacon Pole … E-19
Figure E-19. Standard Details for Wind Cone Foundation (L-807) … E-20
Figure E-20. Standard Details for Wind Cone – 12 ft (3.7 m) Wind Cone … E-21
Figure E-21. Standard Details for Precision Approach Path Indicators (PAPIs) – PAPI Light
Unit Locations … E-22
Figure E-22. Standard Details for Precision Approach Path Indicators (PAPIs) … E-23
Figure E-23. Standard Details for Precision Approach Path Indicators (PAPIs) – Section A-A . E-
24
Figure E-24. Standard Details for Runway End Identifier Light Power and Control Derived from
Runway Circuit – Profile View … E-25
Figure E-25. Standard Details for Runway End Identifier Light Power and Control Derived from
Runway Circuit – Plan View … E-26
Figure E-26. Location of Entrance-Exit Lights (in Lieu of Guidance Signs) … E-27
CONTENTS
Number Page
xvi
Figure F-1. Controlled Output Sign Block Diagram … F-2
Figure F-2. Typical Power Line Carrier System … F-4
Figure F-3. Load Example for In Pavement RGL Circuit … F-11
Figure F-4. ALCMS Block Diagram from AC 150/5345-56 … F-15
Figure G-1. REL Configuration for Taxiways at 90 Degrees … G-3
Figure G-2. Angled Configuration … G-4
Figure G-3. Takeoff/Hold Lights … G-6
Figure H-1. Runway and Threshold Lighting Configuration (LIRL Runways and MIRL Visual
Runways) (Legacy Figure 2) … H-2
Figure H-2. Runway and Threshold Lighting Configuration (HIRL Precision Instrument
Approach - Runway Centerline Not Shown for HIRL; Non-precision Instrument Approach for MIRL) (Legacy Figure 3) … H-3
Figure H-3. Runway with Blast Pad (No Traffic) (Legacy Figure 5) … H-4
Figure H-4. Lighting for Runway with Displaced Threshold (Legacy Figure 6) … H-5
Figure H-5. Normal Runway with Taxiway (Legacy Figure 7) … H-6
Figure H-6. Lighting for Runway with Displaced Threshold (Legacy Figure 8) … H-7
Figure H-7. Lighting for Runway with Displaced Threshold/Usable Pavement (Legacy Figure
9) … H-8
Figure H-8. Lighting for Runway with Displaced Threshold Not Coinciding with Opposite
Runway End (Legacy Figure 10) … H-9
Figure H-9. Lighting for Runway with Stopway (Legacy Figure 11) … H-10
Figure H-10. Lighting for Runway with Displaced Threshold and Stopway (Legacy Figure 12)
… H-11
Figure H-11. Typical Straight Taxiway Sections (Less Than 200 ft (61 m)) (Legacy Figure 16)
… H-12
Figure H-12. Spacing of Lights on Curved Taxiway Edges (Legacy Figure 17) … H-13
CONTENTS
Number Page
xvii
Figure H-13. Typical Single Straight Taxiway Edges (More Than 200 ft (61 m)) (Legacy Figure
18) … H-14
Figure H-14. Typical Single Straight Taxiway Edges (Less Than 200 ft (61 m)) (Legacy Figure
19) … H-15
Figure H-15. Typical Taxiway Edge Lighting Configuration (Legacy Figure 20) … H-16
Figure H-16. Typical Taxiway Edge Lighting for Portions of Runways Used as Taxiway (When
Taxiway Lights Are “ON”) (Legacy Figure 21) … H-17
Figure H-17. Typical Edge Lighting for Portions of Runways Used as Taxiway (When Runway
Lights Are “ON”) (Legacy Figure 22) … H-18
TABLES
Table 2-1. Straight Taxiway Edge Light Spacing … 2-7
Table 2-2. Edge Lighting System Design Guide … 2-13
Table 2-3. Equipment and Materials … 2-16
Table 4-1. Longitudinal Dimensions … 4-5
Table 4-2. Equipment and Material Used for Low Visibility Lighting Systems … 4-28
Table 5-1. Equipment and Material Used for Land and Hold Short Lighting Systems … 5-6
Table 7-1. Threshold Crossing Heights … 7-11
Table 7-2. Aiming of Type L-880 (4 Box) PAPI Relative to Pre-Selected Glide Path … 7-12
Table 7-3. Aiming of Type L-881 (2 Box) PAPI Relative to Pre-Selected Glide Path … 7-12
Table 8-1. Interface of Radio Control with Airport Visual Aids … 8-5
Table 13-1. AGL Control System Response Times … 13-7
xviii
Page Intentionally Blank
CHAPTER 1 INTRODUCTION
1.1. General. Numerous airport visual aids are available to provide information and guidance to pilots maneuvering on airports. These aids may consist of single units or complex systems composed of many parts. Often visual aids have different performance requirements and configurations, but may share common installation procedures. For example, installation procedures for in-pavement lighting systems are essentially the same, yet the lighting systems may perform different functions. This advisory circular (AC) provides installation details for all airport visual aids in one document. Performance specifications and configuration details for the various visual aids can be found in the referenced ACs. Drawings in Appendix E depict typical installation methods for various types of airport lighting equipment.
Chapter 1 INTRODUCTION › 1.4. Mixing of Light Source Technologies.
1.2. Scope. This AC provides installation methods and techniques for airport visual aids. The standards contained herein are standards the FAA requires in all applications involving airport development of this nature. These standards must be met where lighting systems are required for FAA-developed procedures. Installations should conform to the National Fire Protection Association (NFPA) National Electrical Code (NEC) and local codes where applicable. See referenced materials.
1.3. Safety. Airports present a unique working environment. Airplanes traveling at high speed, multi-directional traffic, noise, and night work are a few of the conditions that may confront a construction worker on an airport. Safety is of paramount concern to all parties. We encourage you to become familiar with FAA guidance contained in AC 150/5370-2, Operational Safety on Airports During Construction. Additionally, we recommend you to be familiar with occupational safety and health requirements per 29 CFR 1910 and 1926.
1.4. Mixing of Light Source Technologies. The increasing use of airport light emitting diode (LED) light fixtures on the air operations area (AOA) has caused concerns when LED light fixtures are interspersed with their incandescent counterparts. LED light fixtures are essentially monochromatic (aviation white excepted) and may present a difference in perceived color and/or brightness than an equivalent glass or plastic filtered incandescent fixture. These differences can potentially distort the visual presentation to a pilot. Therefore, LED light fixtures must not be interspersed with incandescent lights of the same type.
Example: An airport adds an extension to a runway. On the existing runway, the runway centerline light fixtures are incandescent. The airport decides to install LED runway centerline fixtures on the new section of runway and retains the incandescent
Chapter 1 INTRODUCTION › 1.6. High Voltage Series Circuit Power.
fixtures on the existing section. This interspersion of dissimilar technology is not approved for installation.
In addition, defective incandescent fixtures must not be replaced with their LED counterparts. When replacing a defective light fixture, make certain that the replacement uses the same light source technology to maintain a uniform appearance.
LED Technology System(s) that are not to be interspersed:
• Runway Guard Lights (RGLs) – each pair of elevated RGLs must be the same technology. For in-pavement lights, do not mix LED with incandescent fixtures in the same bar.
• Touchdown Zone Lights.
• Runway Edge Lights including Threshold, End, and Stopway.
• Signs per location – do not collocate LED signs with incandescent signs. Example: runway holding position signs on both sides of a taxiway, holding position signs on both sides of a runway, separate signs that form a sign array.
• Taxiway curved segments (centerline and edge).
• Taxiway Straight Segments (centerline and edge).
• Approach Light Systems.
• Stop Bars.
• Runway Centerline.
• Lead-on and Lead-off Lights.
• Precision Approach Path Indicator (PAPI).
1.5. Airports Geographical Information System (GIS) Database. When airport visual aids are newly installed or relocated, all relevant information in the Airports GIS database should be updated and verified by National Geodetic Survey (NGS) per AC 150/5300-18, General Guidance and Specifications for Submission of Aeronautical Surveys to NGS: Field Data Collection and Geographic Information System (GIS) Standards.
1.6. High Voltage Series Circuit Power. Do not use the high voltage series lighting circuit to power devices that are not certified per AC 150/5345-53, Airport Lighting Equipment Certification Program, listed in Appendix 3, Addendum. Using non-certified devices can result in a poor system power factor resulting in unexpected constant current regulator (CCR) shutdowns and lighting circuit start-up problems.
Chapter 2 RUNWAY AND TAXIWAY EDGE LIGHTING SYSTEMS › 2.3. Runway Edge Light Configurations.
CHAPTER 2 RUNWAY AND TAXIWAY EDGE LIGHTING SYSTEMS
2.1. General. Edge lighting systems are used to outline usable operational areas of airports during periods of darkness and low visibility weather conditions. These systems are classified according to the intensity or brightness produced by the lighting system.
This chapter covers standards for the design and installation of the following systems (see Figure A-1 for the legend for Figure A-2 through Figure A-21).
2.1.1 Runway Edge Lighting Systems. Runway edge lights define the edge of the runway. The following standard systems are described in this section:
• Low Intensity Runway Lights (LIRL)
• Medium Intensity Runway Lights (MIRL)
• High Intensity Runway Lights (HIRL)
2.1.2 Taxiway Edge Lighting Systems. Taxiway edge lights define the edge of the taxiway or apron. The standard taxiway edge lighting system for airports is described in this section:
• Medium Intensity Taxiway Lights (MITL)
2.2. Selection Criteria. The selection of an edge lighting system is based on the operational needs per the following guidelines:
• LIRL install on visual runways (for runways at small airports).
• MIRL install on visual runways or non-precision instrument runways.
• HIRL install on precision instrument runways.
• MITL install on taxiways and aprons at airports where runway lighting systems are installed.
The airport surface requirements for specific approach procedures are the determining factor for the runway lighting system selection. See AC 150/5300-13, Airport Design, for more information. Any runway edge lighting system requires that the airport be equipped with a rotating beacon meeting the requirements of AC 150/5345-12, Specification for Airport and Heliport Beacons.
2.3. Runway Edge Light Configurations. A runway edge lighting system is a configuration of lights that defines the lateral and longitudinal limits of the usable landing area of the runway. Two straight lines of lights installed parallel to and at equal distances from the runway centerline define the lateral
limits. The longitudinal limits of the usable landing area are defined at each end of the area by straight lines of lights called threshold/runway end lights, which are installed perpendicular to the lines of runway edge lights. Table 2-3 provides information on the recommended light fixture for each application.
2.3.1 Edge Lights.
2.3.1.1 Colors. 2.3.1.1.1 LIRL. The runway edge lights emit white light per Figure A-2.
2.3.1.1.2 MIRL and HIRL.
1. The runway edge lights emit white light except in the caution zone (not applicable to visual runways) which is the last 2,000 ft (610 m) of runway or one-half the runway length, whichever is less.
2. In the caution zone, yellow lights are substituted for white lights; they emit yellow light in the direction facing the instrument approach threshold and white light in the opposite direction.
3. Instrument approach runways are runway-end-specific, meaning a runway may have an instrument approach on one end and a noninstrument approach on the opposite end.
4. When there is an instrument approach at each runway end, yellow/white lights are installed at each runway end in the directions described above. The yellow lights indicate caution on rollout after landing. An example is shown in Figure A-3.
2.3.1.2 Location and Spacing. 2.3.1.2.1 General.
1. The runway edge lights are located on a line parallel to the runway centerline at least 2 ft (0.6 m), but not more than 10 ft (3 m), from the edge of the full-strength pavement designated for runway use.
2. On runways used by jet aircraft, we recommend 10 ft (3 m) to avoid possible damage by jet blast. On runways not used by jet aircraft, we recommend 2 ft (0.6 m).
3. The edge lights are uniformly spaced and symmetrical about the runway centerline, such that a line between light units on opposite sides of the runway is perpendicular to the runway centerline.
4. Longitudinal spacing between light units must not exceed 200 ft (61 m), except as described in paragraph 2.3.1.2.2 item 1.
5. Use the threshold/runway end lights as the starting reference points for longitudinal spacing calculations during design.
Note: See AC 150/5340-26, Maintenance of Airport Visual Aid Facilities, for additional information about the toe-in of runway edge light fixtures.
Follow the manufacturer’s instructions for proper light fixture toe-in alignment.
2.3.1.2.2 Intersections.
1. LIRL/MIRL. For runways with MIRL or LIRL installed and where the configuration of the runway intersection does not allow for the matching of the runway edge lights on opposite sides of the runway to be maintained, the distance between light units on the same side of the runway must not exceed 400 ft (122 m). See Figure A-2, note 3, for maintaining uniform spacing at intersections.
2. MIRL. If the distance between the runway edge lights units is greater than 400 ft (122 m), install an L-852D, taxiway centerline light fixture (per AC 150/5345-46, Specification for Runway and Taxiway Light Fixtures), modified to produce white light (by removing the filters if an incandescent lamp is used) or white/yellow, and maintain the designed spacing per Figure A-3.
3. HIRL. For runways approved for instrument landing system (ILS) CAT III operations with HIRL installed at runway intersections, install L-850C, flush in-pavement light fixtures (described in AC 150/5345- 46), to maintain uniform spacing. For other operations on runways with HIRL, the installation of an in-pavement fixture should be based on the following:
4. The availability of other visual cues at the intersection, such as guidance signs or centerline lighting.
5. The geometric complexity of the intersection, such as crossing runways. If the gap exceeds 400 ft (122 m) install an in-pavement light fixture to maintain uniform spacing.
6. Whether the addition of an in-pavement fixture could confuse ground operations.
2.3.1.2.3 Runway Sections Used as Taxiways.
1. For runway or sections of runways used as taxiways, the runway/taxiway must have the specified runway lights with the designed spacing maintained on the dual-purpose area.
2. It is permissible to install taxiway edge lights on the dual-purpose area. However, taxiway centerline lighting compliant with Chapter 4 is preferred.
3. Design the control systems such that either the taxiway lights or the runway lights are on. Runway and taxiway lights must not be illuminated at the same time.
4. All runway lights must be off when the runway’s taxiway lights are illuminated.
5. See Figure A-22 and Figure A-23.
6. In some cases, where a section of the runway is used as a taxiway, it may be desirable to install a controllable stop bar to prevent taxiing aircraft from entering an intersecting runway.
7. The stop bar should be interlocked with the taxiway lights so that it is on when the taxiway lights are on.
2.3.2 Threshold/Runway End Lights.
2.3.2.1 Color. 2.3.2.1.1 Runway Thresholds.
1. Threshold lights emit green light outward from the runway and emit red light toward the runway to mark the ends of the runway.
2. The green lights indicate the landing threshold to arriving aircraft and the red lights indicate the end of the runway for departing aircraft.
3. The red and green lights are usually combined into one fixture and special lenses or filters are used to emit the desired light in the appropriate direction.
4. The layout details for runway threshold lights are shown in Figure A-2, Figure A-3, and Figure A-4.
2.3.2.1.2 Displaced Runway Thresholds.
1. When the runway threshold is displaced, the edge lights located in the area before the threshold emit red light toward the approach.
2. The threshold lights located at the displaced threshold emit green light outward from the runway threshold.
3. Examples of threshold lighting when the landing threshold is displaced from the actual runway threshold are per Figure A-5. Refer to AC 150/5300-13, the Declared Distances paragraph, for additional information about obstructions with regard to displaced runway thresholds and declared distances.
2.3.2.1.3 Light Fixtures.
1. Light fixtures in each group on both sides of a runway threshold should be either all elevated or all in pavement.
2. Mixing of elevated and in-pavement light fixtures in the same group will result in inconsistent light output.
3. See AC 150/5345-46 for standard elevated light fixture height.
4. Each group of light fixtures are to be either inboard or outboard.
2.3.2.2 Location and Spacing. 2.3.2.2.1 General. The threshold and runway end lights are located on a line perpendicular to the extended runway centerline at least 2 ft (0.6 m) but not more than 10 ft (3 m) before the designated runway threshold. See Figure A-3.
1. The lights are installed in two groups located symmetrically about the extended runway centerline. The outermost light in each group is located in line with the runway edge lights.
2. The other lights in each group are located on 10 ft (3 m) centers toward the extended runway centerline. Coordinate locations and spacing of threshold/runway end lights with other plans for future lighting equipment.
3. Approach lighting systems are equipped with a green threshold light bar located 2 ft (0.6 m) to 10 ft (3 m) before the runway threshold (see Figure A-78).
4. If other airport navigational equipment that is installed at the threshold prevents the lights from being properly spaced, each light in a group may be offset not more than 1 ft (0.3 m) in the same direction.
5. For runways with LIRL/MIRL, threshold/runway end lights installed on visual runways with LIRL or MIRL must have three lights in each group per Figure A-2.
6. For runways with MIRL/HIRL, threshold/runway end lights installed on non-precision instrument runways with MIRLs and precision instrument runways with HIRLs must have four lights in each light group per Figure A-3.
2.3.2.2.2 Displaced Threshold. When the threshold is displaced from the end of the runway or paved area, and access by aircraft prior to the threshold is allowed, the threshold lights are located outboard from the runway per Figure A-5.
1. The innermost light of each group is located in-line with the line of runway edge lights, and the remaining lights are located outward, away from the runway, on 10 ft (3 m) centers on a line perpendicular to the runway centerline.
2. When the displaced runway area is usable for takeoff, red/yellow runway edge lights are installed to delineate the outline of this area, per Figure A-5.
3. Maintain the same uniform spacing for runway edge lighting inside the displaced threshold as they are outside of the displaced threshold. Longitudinal spacing between light units must not exceed 200 ft (61 m), except as described in paragraph 2.3.1.2.2 item 1.
2.3.2.2.3 Runways Where Declared Distances are Adjusted. Airport designs for constrained airports may require a reduction to the runway declared distance to meet runway safety area (RSA), runway object free area (ROFA), or the runway protection zone (RPZ) standards.
Chapter 2 RUNWAY AND TAXIWAY EDGE LIGHTING SYSTEMS › 2.5. Taxiway Edge Lights.
2.4. Stopway Edge Lights. Definition of a stopway: A stopway is an area beyond the takeoff runway, centered on the extended runway centerline, and designated by the airport owner for use in decelerating an airplane during an aborted takeoff.
The stopway must be at least as wide as the runway and able to support an airplane during an aborted takeoff without causing structural damage to the airplane. See Figure A-10 and Figure A-11 for illustrations of stopways.
2.4.1 Color. The stopway edge lights emit unidirectional red light in the takeoff direction of the runway.
2.4.2 Location and Spacing. Stopway lights are placed along its full length in two parallel rows that are equidistant from the runway centerline and coincident with the rows of runway edge lights.
2.4.2.1 The spacing between the lights and distance from the edge is the same as runway edge lights per paragraph 2.3.
2.4.2.2 Lights must also be placed at the end of the stopway (spaced symmetrically in relation to the extended runway centerline) and no more than 10 ft (3 m) outboard of the stopway edge per Figure A-10 and Figure A-11.
2.4.2.3 For visual runways with LIRL/MIRL, use two groups of three lights. For non-precision and precision instrumented runways use two groups of four lights. If one runway end is visual and the other runway is nonprecision/precision, then two groups of four should be used.
2.5. Taxiway Edge Lights. Taxiway edge lighting systems are configurations of lights that define the lateral limits of the taxiway or apron. Reflectors may be installed per paragraph 2.5.4 in lieu of, or to enhance, taxiway edge lights.
Note: The use of in-pavement taxiway edge lighting fixtures should be restricted to where elevated lights may be damaged by jet blast or where elevated lights would interfere with aircraft operations.
Note: See AC 150/5300-13, Chapter 4, for new information for taxiway fillet design using newly formulated Taxiway Design Groups (TDG). The TDG is based upon the aircraft main landing gear width (MGW) and the distance from the cockpit to the main
landing gear centroid (CMG). For existing construction, fillets should be upgraded to allow cockpit-over-centerline steering before the installation of taxiway edge lights.
2.5.1 Color. The taxiway edge lights emit blue light, and edge reflectors reflect blue.
2.5.2 Height. The standard installed height of elevated taxiway light fixtures must not exceed 14 inches (355.60 mm) from the bottom of the light-emitting surface to ground level.
See Figure A-109 for additional details about light fixture height versus lateral location requirements in areas with high snowfall.
2.5.3 Spacing. The spacing for taxiway edge lights is calculated based on the taxiway configuration. The methods of calculating taxiway edge light spacing are described below:
2.5.3.1 Straight Taxiway Sections. The edge lights are spaced symmetrically about the taxiway centerline, as outlined in Table 2-1. The taxiway edge lights are located on a line parallel to the taxiway centerline at least 2 ft (0.6 m), but not more than 10 ft (3 m), from the edge of the full-strength pavement designated for taxiway use.
Note: In the event that taxiway edge lights are installed 10 ft. (3m) from the edge of pavement, these lights will be more than 10 ft. (3m) from the near edge of the Intersection Point (IP).
Lights installed on opposite sides of a straight taxiway are aligned such that opposing lights are in a line perpendicular with the taxiway centerline.
Examples of taxiway lighting for straight taxiway sections are shown in Figure A-15, Figure A-19, and Figure A-20.
See paragraph 2.5.3.2.4 for spacing of lights on straight sections in a turn or intersection.
Table 2-1. Straight Taxiway Edge Light Spacing
Section Length (L) Number, Edge Lights
(N) (per side)1 Maximum Spacing (Max) Spacing
(S) L ≤ 50 ft (15 m) 2 50 ft (15 m) L L > 50 ft (15 m) and L ≤ 100 ft (30 m) 3 50 ft (15 m) L/2
L > 100 ft (30 m) and L ≤ 200 ft (61 m)
3 [(L/max) + 1]2, 3
100 ft (30 m) 50 ft (15 m) (single edges) L/2 L/(N-1) 3 L > 200 ft (61 m) [(L/max) + 1]2 100 ft (30 m) (single edges) 3 200 ft (61 m) L/(N-1)
1. Number (N) excludes lights required for end and entrance/exit indicators. 2. Round value up to the next whole number, i.e., 1.31 becomes 2. 3. Applies to single straight taxiways or aprons, where only one side exists. See Figure A-19 and Figure A-20.
2.5.3.2 Curved Taxiway Sections. Curved taxiway sections are designed to allow cockpit-over-centerline steering. See AC 150/5300-13A, paragraph 406.
Curved taxiway edges require shorter spacing of edge lights. The spacing is determined based on the radius of the arc of the edge lights. The applicable spacing for curves is per Figure A-16. For radii not listed in Figure A-16, determine spacing by the linear interpolation method.
2.5.3.2.1 The taxiway edge lights are uniformly spaced. Arcs of more than 30 degrees must have at least three edge lights.
2.5.3.2.2 Locate the last light of the straight section directly in line with the PT of the intersecting taxiway or apron.
2.5.3.2.3 Taxiway edge light spacing on curved sections at other than 14 CFR Part 139 certificated airports may be reduced per Figure A-116. In such cases, like curves on an airport will have the same spacing. A categorization of general aviation airports can be found at https://www.faa.gov/airports/planning_capacity/passenger_allcargo_stats/ categories/.
2.5.3.2.4 Because L-1 is a gradual taper, light spacing along L-1 must align with the respective outer edge straight segments. The gradual taper is treated as part of the straight segment. The spacing used along the straight section prior to the intersection of the taxiway must continue along the L-1 taper.
2.5.3.2.5 A light must be placed at the intersection point (IP) of the L-1 and L-2 tapers, and on the opposite edge of the taxiway directly across from this point, per Figure A-17.
2.5.3.2.6 A light must be placed at the intersection of the L-2 taper and any curved fillets. Where there is no curved fillet (R-FILLET=0), a light must be installed at the intersection of the two L-2 tapers.
2.5.3.2.7 The maximum spacing of the edge lights for L-2 tapers must not exceed 50 feet (15.2 m).
2.5.3.2.8 Per Figure A-17, use single straight segment spacing requirements for straight sections that are opposite L-2 tapers. Use typical straight taxiway light spacing to establish the spacing for the straight segments opposite of the L-2 tapers. Note that the straight segment is defined as a point aligned with the L-2 IP and the outside curve’s point of tangency.
2.5.3.2.9 Taxiway curve indicators are a subset of taxiway edge lights that indicate the approach of the taxiway curve or intersection. They are additional taxiway edge lights installed before the intersection. These lights are installed on sections of taxiways that are at least 200 ft (61 m) long, where edge light spacing exceeds 60 ft (18 m). Install taxiway curve indicator lights prior to intersections and curves per Figure A-16. These lights are installed 50 feet (15.2 m) prior to the point of tangency of the outer pavement edge. Figure A-19 shows typical placement of curve indicators.
2.5.3.2.10 See Figure A-17 for an example of a taxiway edge lighting layout and additional details.
2.5.3.3 Closely Spaced Turns. Certain configurations (e.g. some runway/taxiway intersections and crossover taxiways) result in the intersection of fillet tapers. Use the light spacing rules described above to place the fillet taxiway edge lights, along with additional details below.
2.5.3.3.1 Runway/Taxiway Intersections. See AC 150/5300-13A, paragraphs 407 - 409.
1. 90 degree runway/taxiway intersections that are not at the end of the runway are treated as four 90 degree turns. Where fillets meet at an IP, a light is placed on the inside edge at the narrowest point. Install the last taxiway edge light on the pavement edge at the point of intersection of the runway edge light line plus a 3-foot (1 m) offset and the taxiway edge light line. See AC 150/5300-13A, paragraph 409.
2. Runway/taxiway intersections at the end of the runway (i.e. entrance taxiways, which should always be 90 degree intersections) are treated as two 90 degree turns, similar to crossover taxiways. Where fillets meet at an IP, a light is placed on the inside edge at the narrowest point. The placement of a light on the opposite side of the narrowest paved segment is required unless the opposite side straight segment has a light within 10 feet (3 m) of the opposite location based on a single-sided light layout. Install the last taxiway edge light on the inside pavement edge at the point of intersection of the runway edge light line plus a 3-foot (1 m) offset and the taxiway edge light line. Install the last taxiway edge light on the outside pavement edge 10 feet (3 m) from the closest runway end light. See AC 150/5300-13A, paragraph 409.
3. High speed exit taxiways are special cases using a combination of curved and straight sections. Install the last taxiway edge light on the pavement edge at the point of intersection of the runway edge light line plus a 3-foot (1 m) offset and the taxiway edge light line. See AC 150/5300-13A, paragraph 409.
4. The taxiway lighting fillet segment length “L” must start at the taxiway fillet IP and continue to a point on a line parallel to and offset 3 feet (1 m) outboard of the runway edge light line. The taxiway lighting is based on the point of intersection of the runway edge light line plus a 3-foot (1 m) offset, with the taxiway light line.
5. Taxiway lighting along the taper is spaced based upon the length of the segment “L.” Refer to Table 1 of Figure A-18 for recommended spacing requirements.
6. If the intersection with the taxiway lighting segment is on a curve, the point of intersection is treated as a PT and the taxiway light spacing is
per this AC. If the curve has a W-3, a light is placed at W-3 and the light line curve spacing is based on the PT and W-3 point.
2.5.3.3.2 Crossover Taxiways. Crossover taxiways are treated as four 90-degree turns. Where there is not a straight section between curves, install lights opposite one another at the narrowest point. See AC 150/5300-13A (paragraph 411, Figure 4-23 and Figure 4-24). See Figure A-12 for additional design guidance.
2.5.3.4 Taxiway Edge Lights in lieu of Guidance Signs at Runway-Taxiway Intersections.
1. Taxiway guidance signs are installed at runway-taxiway intersections to define the throat or entrance into the intersecting taxiing route.
2. At non-CFR Part 139 airports, where taxiway signs would interfere with aircraft operations, or at small general aviation (GA) airports, dual taxiway lights spaced per Appendix E, Figure E-26, may be installed instead of the sign. See https://www.faa.gov/airports/planning_capacity/passenger_allcargo_st ats/categories/ for a categorization of general aviation airports.
3. The taxiway lights used are L-861T fixtures. Taxiway lights used per the above must be illuminated when the runway edge lights are on.
2.5.4 Use of Reflectors. Reflectors are permitted to enhance taxiway lighting systems installed on short taxiway sections, curves, and intersections (see Figure A-15 and Figure A-16).
2.5.4.1 Lights are installed to meet the spacing requirements and reflectors are installed uniformly between the lights.
2.5.4.2 Reflectors are also permitted in lieu of edge lights where a centerline system is installed.
2.5.4.3 Reflectors must be installed using the required spacing for taxiway edge lights as specified in this AC.
2.5.4.4 See AC 120-57, Surface Movement Guidance and Control System, for additional guidance about the use of retroreflective markers.
2.5.4.5 Figure A-109 (which shows elevated light height versus the distance from the defined pavement edge) must also apply to the use of Type II retroreflective markers in areas with high snowfall.
2.5.4.6 Retroreflective markers are described in AC 150/5345-39, Specification for L-853, Runway and Taxiway Retroreflective Markers.
Chapter 2 RUNWAY AND TAXIWAY EDGE LIGHTING SYSTEMS › 2.6. System Design.
2.6. System Design. Coordinate the lighting system design with the existing and future airport plans. Airport drawings will show existing system(s) layout and available utilities. Install the conduits and ducts needed for the lighting system prior to paving operations to eliminate the expense of installing these utilities in existing pavement. Airport drainage systems may influence the location of cable ducts and trenches. Develop design drawings showing the dimensional layout of the lighting system prior to construction. Examples of system layouts are per Figure A-21, Figure A-22, and Figure A-23, for high-density traffic airports.
2.6.1 Lighting Fixtures. The lighting fixtures installed in the edge lighting systems are either base-mounted or stake-mounted.
2.6.1.1 Base mounts are used for either elevated fixtures or in-pavement fixtures.
2.6.1.2 In-pavement light fixtures are not permitted for the full length of the runway. They are typically used in areas where aircraft may roll over the fixture and require load-bearing bases.
2.6.1.3 Stake mounting is typically less expensive than base mounting; however, base mounting provides additional protection for this equipment and makes the equipment more accessible for maintenance. Stake mounting requires the transformers, cables, and connectors be buried in the earth. A typical drawing of light fixture mountings is per Figure A-24.
2.6.1.4 Base-mounted fixtures must be installed using series circuits only and are recommended for HIRL, MIRL, or MITL.
2.6.1.5 Stake-mounted fixtures can be installed with either series or parallel circuits.
2.6.2 Electrical Power (Series vs. Parallel Circuits). Series powered circuits with isolation transformers are recommended for HIRL, MIRL, and MITL lighting systems.
2.6.2.1 The advantages of the series circuits are:
• Uniform lamp brightness.
• Lower installation cost for long runways, generally over 4,000 ft (1219 m) long.
• Reduced cold-start burnouts and in-rush currents on turn-on.
• Unintentional grounding will not shut the system down.
2.6.2.2 Parallel power circuits are recommended for LIRL, but may also be used for MIRL or MITL. Parallel circuits have a lower installation cost for short runways, 4,000 ft (1219 m) or less.
2.6.2.3 Parallel circuits should be designed using a 120/240-volt AC, singlephase, 3-wire system with a shared neutral. Interleave the circuits so that each adjacent fixture is on a separate leg.
2.6.2.4 Series circuits may also be interleaved, considering requirements for equipment such as regulators and adjacent lamp monitoring during design of the system.
2.6.2.5 If two or more circuits are used to power the edge lights for one runway, and loss of power to any of those circuits will leave more than 400 ft (122 m) of the runway without edge lights, the circuits should be coupled such that if one is energized both are energized, or if one is de-energized both are de-energized.
2.6.2.6 For additional technical information about airport lighting circuit interleaving, see International Civil Aviation Organization (ICAO), Aerodrome Design Manual, Document 9157-AN/901, Part 5, Electrical Systems.
2.6.3 Power Source and Monitoring. Series-powered airport lighting circuits are powered by CCRs. The CCRs and the associated monitoring system are described in AC 150/5345-10, Specification for Constant Current Regulators and Regulator Monitors. The CCRs are designed to provide the desired number of brightness steps.
2.6.3.1 Some CCRs emit electromagnetic interference (EMI) that may degrade the performance of other air navigational equipment, such as computers, radars, instrument landing systems, radio receivers, very high frequency omnidirectional radio ranges, etc.
2.6.3.2 See Appendix B for more information about potential airport EMI.
2.6.3.3 Runway edge lighting systems that support CAT II or CAT III operations should be remotely monitored and must provide the monitoring information to the Airport Traffic Control Tower (ATCT). See section 8 “Visual Aid Requirements” of AC 120-57 for remote monitoring requirements.
2.6.3.4 See AC 150/5345-56, Specification for L-890 Airport Lighting Control and Monitoring System (ALCMS), for additional information about monitoring systems.
2.6.3.5 See AC 150/5340-26, Appendix A, Standards and Tolerances, for airport lighting operational tolerances.
Table 2-2. Edge Lighting System Design Guide
Lighting
System
Installation Fixture Power System
Number
of Steps
Associated
Threshold
Type Mounting Design Fixtures
Runway Edge Lighting
HIRL
Inset 1 Base L-850C
Series 5 8 lights L-862E Elevated Base or
Stake
L-862
MIRL
Inset 1 Base L-852D Series
3 6 or 8 lights
L-861SE2
L-861E2 Elevated Base or
Stake
L-861 Series or
Parallel
LIRL Elevated Base or
Stake L-860 Series or
Parallel 1 6 lights L-860E
Taxiway Edge Lighting
MITL
Inset Base L-852T Series 3 Elevated Base or
Stake
L-861T Series or
Parallel
3
1 Inset fixtures are not permitted for the full length of the runway. They are typically installed in areas where aircraft may roll over the fixture.
2 For runways with either a PAPI, runway end identifier lights (REIL), medium approach light system (MALS), or lead-in lighting system (LDIN), L-861E light fixture may be installed in lieu of the L-861SE.
3 An L-861SE light fixture should be used for MIRL if there is no PAPI, REIL, MALS, or LDIN present.
2.6.4 Brightness Steps. The brightness of the lamps is specified in steps that are defined as a percentage of the full brightness of the lamp. (AC 150/5345-46 contains the specifications for the light fixtures.) The following tables specify the appropriate lamp current or voltage to achieve each brightness step:
2.6.4.1 HIRL Systems. HIRL systems have five brightness steps:
Percent Brightness Lamp Current
Step 5 100 6.6 A
Step 4 25 5.2 A
Step 3 5 4.1 A
Step 2 1.2 3.4 A
Step 1 0.15 2.8 A
2.6.4.2 MIRL Systems. MIRL and MITL, when installed using a series circuit and powered by an L-828 or L-829 regulator, have three brightness steps:
Percent Lamp Current
Brightness Series Parallel
Step 3 100 6.6 A 120 V
Step 2 30 5.5 A 85 V
Step 1 10 4.8 A 60 V
When MITL are installed using a parallel circuit, only one brightness step is required. In some cases, it may be desirable to provide equivalent brightness steps similar to a 3-step series circuit. This may be accomplished by use of a variable transformer, autotransformer, or other means.
2.6.4.3 LIRL Systems. LIRL have only one brightness step, 100%.
2.6.5 Control Methods.
2.6.5.1 The edge lighting systems should have provisions for local and/or remote control methods.
2.6.5.2 Remote controls are recommended for systems at locations served by an ATCT, flight service station, or other manned offices where the system(s) operates. Refer to Chapter 13 for additional information about control systems.
2.6.5.3 Local controls may be designed using direct switching at the site, or automatic controls such as a photoelectric control device or timer switch with provisions for switching from automatic to manual control.
2.6.5.4 Remote controls may be designed using a fixed-wire method, or radio control with L-854 equipment per AC 150/5345-49, Specification L-854, Radio Control Equipment. Figure A-25, Figure A-26, Figure A-27, Figure A-28, Figure A-29, Figure A-30, and Figure A-31 show some typical applications for remote controls.
2.6.5.4.1 120 Volts AC. Where the distance between the remote-control panel and the vault is not great enough to cause an excessive voltage drop (5%) in the control leads, the standard control panel switches should be used to operate the control relays directly.
Chapter 2 RUNWAY AND TAXIWAY EDGE LIGHTING SYSTEMS › 2.7. Equipment and Materials.
Control relays supplying power to the regulators must have coils rated for the control voltage. Conductor size of the control cable should be of a size that will not cause more than a 5% voltage drop. The voltage rating of the conductor insulation must be rated for the system voltage. Refer to Chapter 13 for additional guidance.
2.6.5.4.2 120 Volts AC – Auxiliary Relay. Special low-burden pilot auxiliary relays, having proper coil resistance to reduce control current, may be used to obtain additional separation distance with 120-volt AC control circuits. It may be advantageous to use these relays to expand existing 120-volt AC control circuits.
2.6.5.4.3 48 Volts DC. Where the distance between control panel and the vault would cause an excessive voltage drop, a low voltage (48-volt DC) control system should be used.
1. In such a system, remote control panel switches activate sensitive pilot relays, such as those specified in AC 150/5345-13, Specification for L- 841 Auxiliary Relay Cabinet Assembly for Pilot Control of Airport Lighting Circuits, which, in turn, control the regulator relays.
2. Use an appropriately sized cable, of a type listed for use as direct earth burial, to connect the control panel to the pilot relays.
3. The DC control system is adequate for up to 7,900 ft (2408 m) separation between control point and vault.
4. For typical application details, see Figure A-30, Figure A-31 and AC 150/5345-3, Specification for L-821 Panels for Control of Airport Lighting.
2.6.6 Runway Visual Range (RVR) Connections.
2.6.6.1 Where RVR equipment is to be installed, provide two No. 12 AWG wires for 120-volt AC control, or two No. 19 wires if 48-volt control is used, between the control tower and the vault.
2.6.6.2 The wires in the vault connect to an interface unit provided with the RVR equipment. The wires in the tower connect to RVR equipment.
2.6.6.3 All RVR connections must be per instructions provided with the RVR system, and be made by personnel responsible for the RVR or their designee.
2.7. Equipment and Materials. Equipment and material covered by ACs are referred to by item numbers and the associated AC numbers where the equipment is specified - all pertinent ACs and specifications are referenced by number and title in Appendix D. Equipment that is not
covered by FAA specifications, such as distribution transformers, circuit breakers, cutouts, relays, and other commercial items of electrical equipment, must conform to the applicable rulings and standards of the electrical industry and local code regulations. Electrical equipment must be tested and certified by an Occupational Safety and Health Administration (OSHA) recognized Nationally Recognized Testing Laboratory (NRTL) and should bear that mark. A current list of NRTLs can be obtained by contacting the OSHA NRTL Program Coordinator. Table 2-3 contains a list of equipment and material used for runway and taxiway edge lighting systems described in this section. See Chapter 12 for additional information:
• Light Bases, Transformer Housings and Junction Boxes. See paragraph 12.2.
• Duct and Conduit. See paragraph 12.3.
• Cable, Cable Connectors, Plugs and Receptacles. See paragraph 12.4.
• Counterpoise (Lightning Protection). See paragraph 12.5.
• Light Fixture Bonding. See paragraph 12.6.
• Concrete. See paragraph 12.7.
• Steel Reinforcement. See paragraph 12.8.
• Adhesive and Sealants. See paragraph 12.9.
• Load-bearing Lighting Fixtures. See paragraph 12.10.
• Inspection. See paragraph 12.11.
• Testing. See paragraph 12.11.1.
• Auxiliary Relays. See paragraph 12.12.
• Vault. See paragraph 12.13.
• Maintenance. See paragraph 12.14.
Table 2-3. Equipment and Materials
Item Description Item No. ACs
Auxiliary Relay Cabinet L-841 AC 150/5345-13
Cable L-824 AC 150/5345-7
Cable Connectors L-823 series circuits L-108 parallel circuits
Circuit Selector Switch L-847 AC 150/5345-5
Control Panel L-821 AC 150/5345-3
Elevated Edge Light Fixture (HIRL) L-862, L-850C1 AC 150/5345-46
Item Description Item No. ACs
Elevated Edge Light Fixture (LIRL) L-860 AC 150/5345-46
Elevated Edge Light Fixture (MIRL) L-861 AC 150/5345-46
Elevated Threshold Light Fixture (HIRL) L-862 AC 150/5345-46
Elevated Threshold Light Fixture (MIRL) L-861SE, L861E 2 AC 150/5345-46
Elevated Edge Light Fixture (MITL) L-861-T AC 150/5345-46
In-pavement Light Fixture L-852 AC 150/5345-46
In-pavement Light Fixture L-850 D, E AC 150/5345-46
Isolation Transformers L-830 AC 150/5345-47
Junction Box4 L-867/L-868, blank covers AC 150/5345-42
Light Base and Transformer Housing 3 L-867, L-868 AC 150/5345-42
Regulators L-828, L-829 AC 150/5345-10
Retroreflective Markers L-853 AC 150/5345-39
Duct and Conduit L-110 AC 150/5370-10
Concrete P-610 AC 150/5370-10
Tape L-108 AC 150/5370-10
Vaults L-109 AC 150/5370-10
1 Install the L-850 C light fixture if in-pavement fixtures are applicable, per paragraph 2.3. 2 For runways with either a PAPI, REIL, MALS, or LDIN, L-861E light fixture may be installed in lieu of the L-861SE. 3 Elevated lights are installed with a 12-inch (size B) Type L-867 base or are stakemounted, and in-pavement light fixtures are installed with a 15-inch (size C) base or a 12-inch (size B) L-868 base. 4 Use an L-867 light base with blanking cover for a junction box or transformer housing that must withstand occasional light vehicular loads. Use an L-868 light base with blanking cover for a junction box or transformer housing that must withstand heavy loads from vehicles or aircraft.
Page Intentionally Blank
Chapter 3 RUNWAY CENTERLINE AND TOUCHDOWN LIGHTING SYSTEMS › 3.3. Configuration.
CHAPTER 3 RUNWAY CENTERLINE AND TOUCHDOWN LIGHTING SYSTEMS
3.1. Introduction. Runway centerline and touchdown zone lighting systems are designed to facilitate landings, rollouts, and takeoffs. The touchdown zone lights are primarily a landing aid while the centerline lights are used for both landing and takeoff operations.
3.2. Selection Criteria. Runway centerline lights and touchdown zone lights are required for CAT II and CAT III runways, and for CAT I runways used for landing operations below 2,400 ft (750 m) RVR.
3.2.1 Runway centerline lights are required on runways used for takeoff operations below 1,600 ft (480 m) RVR unless specifically approved by the FAA in an airline operator’s specification for that runway.
3.2.2 See guidance in FAA Order 8900.1, Flight Standards Information Management Systems (FSIMS), Volume 4, Chapter 2, Section 9, “Lower than Standard Takeoff Minima”.
3.2.3 Although not operationally required, runway centerline lights are recommended for CAT I runways greater than 170 ft (50 m) in width or when used by aircraft with approach speeds over 140 knots Aircraft Approach Category (AAC).
3.3. Configuration.
3.3.1 Runway Centerline Lighting.
3.3.1.1 Location. The runway centerline lights are located along the runway centerline at 50 ft (15 m) equally spaced longitudinal intervals.
3.3.1.1.1 The longitudinal tolerance for runway centerline lights is ±2 ft (0.6 meter).
3.3.1.1.2 See Figure A-34 for a graphic of the runway centerline lighting layout. The line of runway centerline lights may be uniformly offset laterally to the same side of the physical runway centerline by a maximum of 2.5 ft (0.8 m) (tolerance ±1 inch (25.4 mm)), as measured from the physical runway centerline to the fixture centerline.
3.3.1.1.3 For any new runway, the light base installation must be no closer than 2 ft (0.6 m) (measured to the edge of the fixture base) to any pavement joints. Runway extensions of existing runways must use the convention already established for that runway.
3.3.1.1.4 See paragraph 4.3 and Figure A-46 for additional information about the taxiway centerline lighting location requirements related to runway centerline lights for major taxiway turnoffs. See AC 150/5340-1,
Standards for Airport Markings, for additional information about runway centerline marking widths and locations.
3.3.1.2 Color Coding. The last 3,000 ft (900 m) portion of the runway centerline lighting system is color coded to warn pilots of the impending runway end. Alternating red and white lights are installed, starting with red, as seen from 3,000 ft (900 m) to 1,000 ft (300 m) from the runway end, and red lights are installed in the last 1,000 ft (300 m) portion.
3.3.1.3 Displaced Threshold. On runways with centerline lights, the centerline lights are extended into the displaced threshold area.
3.3.1.3.1 If the displaced area is equal to or less than 700 feet (110 m) in length, the centerline lights are blanked out in the approach direction.
3.3.1.3.2 For displaced threshold areas over 700 ft (110 m) in length, the centerline lights in the displaced area are circuited separately from the centerline lights in the non-displaced runway area to permit turning “off” the centerline lights in the displaced area during landing operations.
3.3.1.3.3 If the displaced threshold area also contains a medium intensity approach light system, the control of the approach lights and displaced threshold area centerline lights is interlocked to ensure that when the approach lights are “on”, the displaced area centerline lights are “off”, and vice versa.
3.3.1.3.4 If the displaced threshold area contains a high intensity approach lighting system, separate circuiting of the centerline lights in the displaced area is not required since the high intensity approach lights will “wash out” the centerline lights.
3.3.2 Touchdown Zone Lighting. Touchdown zone lights consist of two rows of transverse light bars located symmetrically about the runway centerline per Figure A-35. Align the lighting fixtures in each row of transverse light bars perpendicular to the runway centerline.
3.3.2.1 Each light bar consists of three unidirectional lights facing the landing threshold.
3.3.2.2 The rows of light bars extend to 3,000 ft (900 m), or one-half the runway length for runways less than 6,000 ft (1800 m), from the threshold with the first light bars located 100 ft (30 m) from the threshold.
3.3.2.3 The light beam of the touchdown zone lights is toed four degrees toward the runway centerline. This is achieved by either installing light fixtures that have had their optical assembly toed four degrees, or by angling the light base four degrees and installing the light fixture.
Chapter 3 RUNWAY CENTERLINE AND TOUCHDOWN LIGHTING SYSTEMS › 3.4. Design.
3.4. Design.
3.4.1 Sequence of Installation.
3.4.1.1 The installation of in-pavement lights should be done, if possible, while the runway is under construction or when an overlay is made. This allows for the installation of L-868 light base and transformer housings with a conduit system, which is preferred.
3.4.1.2 Though lighting may not be programmed at the time of runway paving or overlay, installation of bases and a conduit system should be considered for future installation of in-pavement lighting.
3.4.1.3 Installation of the lighting system after paving is completed is very costly and requires a lengthy shutdown of the runway.
3.4.2 Layout.
3.4.2.1 Provide a design drawing to the airport authority showing the dimensional layout of the centerline and touchdown zone lighting systems prior to construction.
3.4.2.2 Correlate this design with current airport drawings to utilize available ducts and utilities and to avoid conflict with existing or planned facilities.
3.4.3 Runway Centerline and Touchdown Zone.
3.4.3.1 Light Fixtures and Wires. Design these systems for one of the following conditions:
3.4.3.1.1 In new pavements, provide access to cables and transformers through the use of conduits and L-868 transformer bases. This type of installation will reduce downtime and repair costs when the underground circuits require maintenance. See Figure A-36, Figure A-37, and Figure A-38.
3.4.3.1.2 In pavements that are being overlaid, a base and conduit system per Figure A-36 and Figure A-37 may be used. This provides the advantages listed in (a) above.
3.4.3.1.3 In existing pavements, provide recesses or holes for the light fixtures and shallow sawed wireways for electrical conductors. This method does not require the installation of bases and conduits. See Figure A-39, Figure A-40, Figure A-41, Figure A-42, and Figure A-43.
3.4.3.1.4 In existing pavements, the directional boring of a raceway under the pavement along the lighting route is permitted. Core drill a 3 ft (0.91 m) diameter hole at the light location. Install L-868 light bases in the cored hole and connect conduit.
3.4.3.2 Electric Power. 3.4.3.2.1 Design each system as a 20-ampere or 6.6-ampere series circuit using a CCR. Provide each light fixture with an isolation transformer sized by the manufacturer to match the lamp.
3.4.3.2.2 To estimate the size (kilowatt (kW) capacity) of the CCR, allow for the total load for each fixture, as calculated in paragraph 3.4.4.1, plus losses in the feed cable from the regulator around the entire loop.
3.4.3.2.3 Use a 6.6-ampere primary circuit if the total load is 30 kW or less, and a 20-ampere primary circuit if the total load is over 30 kW.
3.4.3.3 Electrical Control. 3.4.3.3.1 Make the centerline lighting system controls independent of the touchdown zone lighting system and the high intensity runway edge lights.
3.4.3.3.2 A normal control circuit is 120-volt AC; see special considerations in the next paragraph. We recommend including a minimum of 20% spare wires in the control cable for future use.
3.4.3.3.3 Refer to Chapter 13 for additional information on control systems.
3.4.4 Special Considerations.
3.4.4.1 The total load of a fixture is calculated as follows:
(𝐿𝐿𝐿𝐿𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚) + [(𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿)𝑥𝑥[1 −(
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇
100 𝑥𝑥
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇
100 )]]
Transformer power factor and efficiency is given in percentage, and is specified in AC 150/5345-47, Specification for Series to Series Isolation Transformers for Airport Lighting Systems.
3.4.4.2 Voltage drop between the ATCT and the CCR must be considered. 3.4.4.2.1 Control voltage at the regulator must be 100 volts AC (minimum).
3.4.4.2.2 If this voltage cannot be maintained, either an auxiliary low current AC relay must be installed at each regulator or a low voltage DC remote control circuit must be used.
3.4.4.2.3 In some instances, it will be more economical, because of material costs, to install a low voltage DC control circuit though the voltage drop is within acceptable limits with the standard 120-volt AC system.
3.4.4.2.4 Refer to Chapter 13 for additional information on control systems.
Chapter 3 RUNWAY CENTERLINE AND TOUCHDOWN LIGHTING SYSTEMS › 3.5. Equipment and Material.
3.5. Equipment and Material.
3.5.1 Specifications and Standards.
3.5.1.1 Equipment and material covered by specifications are referred to by AC numbers.
3.5.1.2 Distribution transformers, oil switches, cutouts, relays, terminal blocks, transfer relays, circuit breakers, and all other commercial items of electrical equipment not in FAA specifications must conform to the applicable rulings and standards of the applicable NFPA 70, NEC.
3.5.2 Light Fixtures.
3.5.2.1 Provide runway centerline light fixtures per AC 150/5345-46, using light fixture Type L-850A (Bidirectional).
3.5.2.2 Provide touchdown zone light fixtures per AC 150/5345-46, using light fixture Type L-850B (Unidirectional).
3.5.3 Isolation Transformers.
3.5.3.1 Provide isolation transformers, L-830 (60 Hz) or L-831 (50 Hertz (Hz)), per AC 150/5345-47.
3.5.3.2 The transformers serve as a means of isolating the light unit from the high voltage of the series circuit.
3.5.3.3 When a lamp filament opens, the continuity of the primary series circuit is maintained by the isolation transformer.
3.5.4 Light Base and Transformer Housings.
3.5.4.1 Where required, provide L-868 light bases per AC 150/5345-42, Specification for Airport Light Bases, Transformer Housings, Junction Boxes, and Accessories.
3.5.4.2 The light bases consist of a cylindrical body with top flange and cable entrance hubs; the user may specify an internal grounding lug.
3.5.4.3 The internal grounding lug is used to bond the fixture to the light base.
3.5.4.4 Certain applications may require additional entrance hubs. Provide necessary covers per AC 150/5345-42.
3.5.5 Constant Current Regulators (CCRs).
3.5.5.1 Provide L-828 or L-829 CCRs per AC 150/5345-10.
3.5.5.2 The CCR is designed for step brightness control without interrupting load current.
3.5.5.3 The CCR assembly has lightning arresters, open circuit and over current protective devices, and a local control switch.
3.5.5.4 All parts are suitably wired at the factory as a complete assembly. Series disconnects are required but are not furnished with the CCR; various ratings are available.
3.5.6 Control Panel.
3.5.6.1 System controls may be installed in the existing control panel if space is available. Otherwise, provide an L-821 remote control panel per AC 150/5345-3.
3.5.6.2 The panel consists of a top panel plate and housing, toggle switches, terminal boards, and brightness controls, as required.
3.5.6.3 The site of the panel and the number of components to be mounted on the panel must be specified for each installation.
3.5.6.4 In areas where lightning is prevalent, lightning arresters should be installed at the terminal points of this panel.
3.5.7 Auxiliary Relay Cabinet.
3.5.7.1 L-841 auxiliary relay cabinet assemblies, manufactured per AC 150/5345- 13 can be obtained for use in 48-volt DC control circuits.
3.5.7.2 The assembly consists of an enclosure containing a DC power supply, control circuit protection, and 20 pilot relays.
3.5.7.3 In areas where lightning is prevalent, lightning arresters should be installed at the terminal points of this cabinet.
3.5.7.4 See Chapter 12, Equipment and Material, for additional information.
• Light Bases, Transformer Housings and Junction Boxes. See paragraph 12.2.
• Duct and Conduit. See paragraph 12.3.
• Cable, Cable Connectors, Plugs and Receptacles. See paragraph 12.4.
• Counterpoise (Lightning Protection). See paragraph 12.5.
• Light Fixture Bonding. See paragraph 12.6.
• Concrete. See paragraph 12.7.
• Steel Reinforcement. See paragraph 12.8.
• Adhesive and Sealants. See paragraph 12.9.
• Load-bearing Lighting Fixtures. See paragraph 12.10.
• Inspection. See paragraph 12.11.
• Testing. See paragraph 12.11.1.
• Auxiliary Relays. See paragraph 12.12.
• Vault. See paragraph 12.13.
• Maintenance. See paragraph 12.14.
Page Intentionally Blank
Chapter 4 TAXIWAY LIGHTING SYSTEMS › 4.1. Introduction.
CHAPTER 4 TAXIWAY LIGHTING SYSTEMS
4.1. Introduction. Taxiway lighting systems such as taxiway centerline lights, RGLs, stop bars, and clearance bars are designed to facilitate taxiing and may be required for airport operations during low visibility conditions. Coordinate these systems with Flight Standards and Air Traffic Control (ATC) for all low visibility operations. See Chapter 2 for taxiway edge lighting systems.
4.1.1 Taxiway Centerline Lights. Taxiway centerline lights provide taxi guidance between the runway and apron areas.
4.1.2 Runway Guard Lights. RGLs provide a visual indication to anyone approaching the runway holding position that they are about to enter an active runway.
4.1.3 Stop Bars. Stop bars provide a distinctive “stop” signal to anyone approaching a runway.
4.1.3.1 In low visibility conditions, controlled stop bars are used to permit access to the active runway.
4.1.3.1.1 Controlled stop bars are controlled individually via L-821 stop bar control panel(s) or via buttons on a touch screen display panel in the ATCT.
4.1.3.1.2 Uncontrolled stop bars are generally “on” for the duration of operations below 1,200 ft (365 m) RVR.
4.1.3.2 Uncontrolled stop bars protect the active runway at taxiway/runway intersections that are not part of the low visibility taxi route.
4.1.3.3 Stop bars are required for operations below 600 ft (183 m) RVR on illuminated taxiways that provide access to the active runway.
4.1.3.4 Stop bars may also be used as a means of preventing runway incursions regardless of visibility conditions. For example, stop bars could be illuminated in certain airfield configurations that would prevent aircraft access from particular taxiways to active, as well as closed runways.
4.1.4 Clearance Bars.
4.1.4.1 In low visibility, clearance bars advise pilots and vehicle drivers that they are approaching a hold point (other than a runway holding position).
4.1.4.2 Clearance bars are installed at designated hold points on the taxiway for operations below 600 ft (183 m) RVR.
Chapter 4 TAXIWAY LIGHTING SYSTEMS › 4.2. Implementation Criteria.
4.1.4.3 At night and in inclement weather, clearance bars advise pilots and vehicle drivers that they are approaching an intersecting taxiway.
4.1.4.4 They are generally installed at taxiway intersections where the taxiway centerline lights do not follow the taxiway curve, per Figure A-44, and where taxiway edge lights are not installed.
4.2. Implementation Criteria. Airports approved for scheduled air carrier operations below 1,200 ft (365 m) RVR are required to have some or all of the various lighting systems (taxiway centerline lights, RGLs, stop bars, and clearance bars) discussed in this chapter per the criteria in AC 120-57, and the FAA-approved Surface Movement Guidance and Control System (SMGCS) plan.
In addition, taxiway centerline lights, RGLs, and stop bars may be installed where a taxiing problem exists. Such problems include, but are not limited to, the following:
4.2.1 Runway Incursions.
4.2.1.1 RGLs provide runway incursion protection regardless of visibility conditions and are recommended at runway holding positions to enhance the conspicuity of the hold position at problem intersections or where recommended by an FAA Runway Safety Action Team (RSAT).
4.2.1.2 Stop bars used for runway incursion prevention will primarily be the uncontrolled type.
4.2.1.2.1 For example, an uncontrolled stop bar may be installed on a high-speed exit to a runway that is never used for entering or crossing the runway to prevent aircraft from inadvertently entering the runway from that exit. 4.2.1.2.2 Controlled and uncontrolled stop bars may also be installed during certain runway use configurations or runway closures to prevent access to the runway. 4.2.1.2.3 Stop bars may also be installed on runways that are used as part of a taxiing route at the intersection with another runway. In this case the stop bar should be interlocked with any taxiway lighting installed on the runway so that the stop bar and taxiway lights will not be illuminated when the runway lights are illuminated. See paragraph 2.3.1.2.3.
4.2.1.3 Color coded (green/yellow) taxiway centerline lights are used to enhance pilot situational awareness of the runway area to reduce potential runway incursions
4.2.2 Complex Taxiway Configurations. Taxiway centerline lights should be installed to improve guidance for complex taxiway configurations. Edge lights may be installed in addition to centerline lights if warranted by operational and weather conditions.
4.2.3 Apron Areas. Taxiway centerline lights should be installed in apron areas where other lighting may cause confusion to taxiing or parking operations.
Chapter 4 TAXIWAY LIGHTING SYSTEMS › 4.3. Taxiway Centerline.
4.3. Taxiway Centerline.
4.3.1 General. A taxiway centerline lighting system consists of unidirectional or bidirectional inpavement lights installed parallel to the centerline of the taxiway.
4.3.2 Color-Coding. Taxiway centerline lights are green except as provided in the following subparagraphs:
4.3.2.1 Lead-off Lights. Taxiway centerline lights which provide visual guidance to persons exiting the runway (lead-off lights) are color-coded to warn pilots and vehicle drivers that they are within the runway environment or instrument landing system/microwave landing system (ILS) critical area.
4.3.2.1.1 Alternate green and yellow lights are installed from the runway centerline (beginning with a green light) to one centerline light position beyond the runway hold or ILS critical area hold position ending with a yellow light.
4.3.2.1.2 The fixture used prior to the runway hold or ILS critical area position must always be bidirectional: green when approached from the taxi direction and yellow when approached from the runway direction.
4.3.2.1.3 If the layout of the lights results in an odd number of color-coded lights, the first two taxiway centerline lights on the runway should be green. See Figure A-45, Detail A, for an example of a lead-off light configuration.
4.3.2.2 Lead-on Lights. Lead-on lights provide visual guidance to pilots entering the runway.
4.3.2.2.1 They are also color-coded with the same yellow/green color pattern as lead-off lights to warn pilots and vehicle drivers that they are within the runway environment or ILS critical area.
4.3.2.2.2 The color-coding begins with a green light at the runway centerline and progresses to one light beyond the runway hold or ILS critical hold position.
4.3.2.2.3 The fixture used prior to the runway hold or ILS critical area position must always be bidirectional: green when approached from the taxi direction and yellow when approached from the runway direction (bidirectional).
4.3.2.3 Taxiway centerline lights that cross a runway are color-coded yellow/green per Figure A-45 Detail B.
4.3.2.3.1 Color coded taxiway centerline lights must end with a bidirectional yellow/green light fixture one centerline light position beyond the runway holding position painted marking or ILS critical area holding position painted marking.
4.3.2.3.2 The bidirectional light must be green for traffic on the taxiway approaching the runway and yellow for traffic crossing the runway.
4.3.2.3.3 Depending on the number of lights required, it may be necessary to use the same color twice on the runway to achieve the required colors for the bidirectional light fixtures before the runway holding position.
4.3.3 Longitudinal and Lateral Spacing. The lights are spaced longitudinally per Table 4-1 for minimum authorized operations above and below 1,200 ft (365 m) RVR.
4.3.3.1 Light fixtures should be installed so that the nearest edge is approximately 2 ft (0.6 m) from any rigid pavement joint. Allow a tolerance for individual fixtures of ±10 percent of the longitudinal spacing specified to avoid undesirable spots.
4.3.3.2 A tolerance of ±2 ft (0.6 m) is allowed for fixtures spaced at 12.5 ft (4 m).
4.3.3.3 Displace centerline lights laterally a maximum of 2 ft (0.6 m) to the nearest edge of the fixture, (2.5 ft (0.7 m) to the centerline of the light fixture) to avoid rigid pavement joints and to ease painting the taxiway centerline marking.
4.3.3.4 Apply this lateral tolerance consistently to avoid abrupt and noticeable changes in guidance; i.e., no “zigzagging” from one side of the centerline to the other.
Note: Taxiway fillets are designed in relation to the centerline of the curve and, therefore, the location of the centerline marking. Displacement of taxiway centerline lights 2.5 ft (0.8 m) to the inside of a curve does not necessitate enlargement of the fillet.
Table 4-1. Longitudinal Dimensions
Maximum Longitudinal Spacing 1,200 ft (365 m) RVR and Above
Below 1,200 ft (365 m)
RVR Radius of Curved Centerlines 75 ft (23 m) to 399 ft (121 m) 25 ft (7.6 m) 2 12.5 ft (4 m) 25 ft (7.6m) 1
400 ft (122 m) to 1199 ft (364 m) 50 ft (15 m) 25 ft (7.6 m)
≥1200 ft (365 m) 100 ft (30 m) 50 ft (15 m) Acute-Angled Exits 50 ft (15 m) 50 ft (15 m) (See Figure A-46 and AC 150/5300-13) Straight Segments 100 ft (30 m) 3 50 ft (15 m) 3
1. A L-852K fixture must be used versus an L-852D. 2. A L-852J fixture must be used versus an L-852B. 3. Short straight taxiway segments may require shorter spacing per paragraphs 4.3.8.
4.3.4 Acute-Angled Exits. For acute-angled exits, taxiway centerline lead-off lights begin 200 ft (61 m) prior to the point of curvature of the designated taxiway path, per Figure A-46.
4.3.4.1 See Figure A-46 for additional details about requirements for light spacing and offsets.
4.3.4.2 If the acute-angled exit is used only as an exit, then install unidirectional centerline light fixtures so that the pilots of an exiting aircraft can only see the lights.
4.3.4.3 On existing systems: if a bidirectional fixture is used, we recommend that blanks be installed in the opposite side of the lead-off fixture so that neither lead-on lights nor lights leading from the parallel taxiway to the holding position would be visible.
4.3.5 Taxiway/Runway Intersections Other Than Acute-Angled Exits. For these exits that lie on low visibility taxi routes, taxiway centerline lead-off lights begin at the point of curvature on the runway if the runway has approach or departure minimums below 600 ft (183 m) RVR.
4.3.5.1 Lead-off/lead-on lights are recommended below 1,200 ft (365 m) RVR. (Extra lead-off/lead-on lights should not be installed before the point of curvature on the runway because they would erode the visual distinction between acute-angled exits and other exits.)
4.3.5.2 Taxiway centerline lead-on lights should extend to the PT on the runway, per Figure A-46, if the runway has departure minimums below 600 ft (183 m) RVR.
4.3.5.3 Where operations are not conducted below 1,200 ft (365 m) RVR, neither taxiway centerline lead-on nor lead-off lights may be installed within the confines of the runway.
4.3.5.4 If the taxiway is perpendicular to and dead-ends into the runway, the taxiway centerline light nearest the runway must be installed 150 ft (45 m) from the centerline of the runway. Otherwise, taxiway centerline lights must not extend into the confines of the runway per Figure A-44.
4.3.6 Taxiways Crossing a Runway.
4.3.6.1 At airports where operations less than 600 ft (183 m) RVR are conducted, color coded (alternating green/yellow per paragraph 4.3.2.3) taxiway centerline lights should continue across a runway if they are installed on a designated low visibility taxi route per the airport’s SMGCS plan (see AC 120-57 for additional information).
4.3.6.2 We also recommend that color coded centerline lights continue across a runway for operations below 1,200 ft (365 m) RVR where the taxiway is an often-used route or there is a jog in the taxiway at the intersection with the runway. Otherwise, taxiway centerline lights must not extend onto the runway.
4.3.7 Taxiways Crossing Another Taxiway.
4.3.7.1 Continue taxiway centerline lighting across the intersection when a taxiway intersects and crosses another taxiway. If the fillets at a given taxiway intersection meet the design criteria in AC 150/5300-13, and the taxiway centerline markings follow the taxiway curves per AC 150/5340- 1, then taxiway centerline lights must be installed per Figure A-48; otherwise, install them per Figure A-44.
4.3.7.2 See paragraph 4.7.1 and 4.7.2 for criteria on the installation of taxiway intersection centerline lights and clearance bars.
4.3.8 Short Straight Taxiway Segments. There must be a minimum of four taxiway centerline lights installed on short straight taxiway segments. See Table 4-1.
4.3.9 Orientation of Light Beam for Taxiway Centerline Lights. Taxiway centerline lights must be oriented as follows, with a horizontal tolerance of ±1 degree.
4.3.9.1 On Straight Portions. On all straight portions of taxiway centerlines, the axis of the light beam must be parallel to the centerline of the taxiing path.
Chapter 4 TAXIWAY LIGHTING SYSTEMS › 4.4. Runway Guard Lights (RGLs).
4.3.9.2 On Curved Portions (Excluding Acute-Angled Exits) with Standard Fillets. Orient the axes of the two beams of bidirectional lights parallel to the tangent of the nearest point of the curve designated as the true centerline of the taxiway path. Orient the axis of a unidirectional light beam so that it is “toed-in” to intersect the centerline at a point approximately equal to four times the spacing of lights on the curved portion. Measure this chord spacing along the curve. See Figure A-49.
4.3.9.3 On Curved Portions (Excluding Acute-Angled Exits) with Non- Standard Fillets. See Figure A-44 for orientation and configuration of bidirectional and unidirectional fixtures for taxiway intersections, taxiway crossing a taxiway, or runway and taxiway curves.
4.3.9.4 Acute-Angled Exits. Orient the axis of a unidirectional light beam so that it is “toed-in” to intersect the centerline at a point approximately equal to four times the spacing of lights on the curved portion. Measure this chord spacing along the curve. Orient the axes of the two beams of bidirectional lights parallel to the tangent of the nearest point of the curve designated as the true centerline of the taxiing path.
4.3.10 Supplemental Taxiway Edge Lights and Elevated Edge Reflectors. Refer to AC 120-57 for criteria about supplementing taxiway centerline lights with taxiway edge lights (L-861T), or elevated edge reflectors (L-853) for low visibility operations.
4.3.10.1 For higher visibilities (>600 RVR), where taxiway edge lights are not installed, taxiway centerline lighting should be supplemented with elevated edge reflectors installed adjacent to the taxiway edge on paved fillets and on curves of radii less than 800 ft (244 m) (measured to the taxiway centerline).
4.3.10.2 Supplemental edge lights may be installed to aid taxi operations when centerline lights are obscured by snow.
4.3.10.3 Space edge lights and reflectors per the requirements in Chapter 2. Supplemental reflectors may also be used in ramp areas.
4.4. Runway Guard Lights (RGLs).
4.4.1 General. Elevated and in-pavement RGLs serve the same purpose and are generally not both installed at the same runway holding position. However, if snow could obscure inpavement RGLs, or there is an acute angle between the holding position and the
direction of approach to the holding position, it may be advantageous to supplement inpavement RGLs with elevated RGLs. Each elevated RGL fixture consists of two alternately illuminated, unidirectional yellow lights. In-pavement RGLs consist of a row of alternately illuminated, unidirectional yellow lights.
4.4.2 Runway Guard Light Selection. There are two configurations of runway guard lights. The following criteria should be used to determine which configuration should be installed at a specific runway holding position.
4.4.2.1 Elevated runway guard lights should be installed at the runway holding position if the taxiway does not have taxiway centerline lights installed and is 150 feet (45 m) wide or less. However, if the taxiway has a stop bar installed at the runway holding position, elevated runway guard lights should be co-located with the stop bar, regardless of taxiway width or the presence of taxiway centerline lights.
4.4.2.2 In-pavement runway guard lights should be installed at the runway holding position if the taxiway has centerline lights installed, or the taxiway is greater than 150 feet (45 m) wide, or a stop bar is installed at the ILS critical area holding position.
4.4.2.3 In-pavement combination stop bar/runway guard light fixtures (dual red/yellow lens) may be installed at the discretion of the airport operator. The yellow in-pavement lights may not be turned on when the stop bar is in operation. If the stop bar is located at an ILS critical area holding position, dual red/yellow fixtures should not be selected. (This would result in the installation of two sets of runway guard lights at different locations which serve the same intersection.)
4.4.3 Location of In-Pavement RGLs. In-pavement RGLs are centered on an imaginary line that is parallel to, and 2 ft (0.6 m) from, the holding side of the runway holding position marking, per Figure A-50.
4.4.3.1 The lights may vary from this imaginary line up to ±2 inches (±51 mm) in a direction perpendicular to the holding position marking. Holding position marking locations are described in AC 150/5340-1.
4.4.3.2 If a conflict with rigid pavement joints occurs, move both the runway holding position marking and the RGLs away from the runway the minimum distance required to resolve the conflict. If other markings (e.g., geographical position markings) are installed, they must be moved as well.
4.4.3.3 Lateral Spacing - Preferred Method. The lights are spaced across the entire taxiway, including fillets, holding bays, etc., at intervals of 9 ft, 10 inches (3 m), ±2 inches (±51 mm), center-to-center, per Figure A-50.
4.4.3.3.1 The lights are spaced in relation to a reference fixture that is installed inline (longitudinally) with existing or planned taxiway centerline lights. However, it is not intended that the reference fixture replace a taxiway centerline light.
4.4.3.3.2 If a conflict between the reference fixture and a centerline light occurs, the reference fixture takes the place of an existing centerline light and a new centerline light is installed per the criteria in paragraph 4.3.3.
4.4.3.3.3 If the holding position marking is intersected by multiple taxiway centerline markings, the reference light fixture is set at the centerline that is used most often.
4.4.3.3.4 A light fixture whose outboard edge falls at a point less than 2 ft (0.6 m) from the defined edge of the taxiway (outboard edge of the taxiway marking) may be omitted.
4.4.3.3.5 Individual light fixtures may be moved laterally a maximum of ±1 foot (305 mm) to avoid undesirable spots, i.e., conduit and rigid pavement joints, etc.
Note: If undesirable spots cannot be avoided in this way, fixtures may be moved no more than 2 ft (0.6 m) using the following alternate method.
4.4.3.4 Lateral Spacing - Alternate Method. The following alternate method of spacing the lights must be followed if it is not possible to meet the preferred method specified in paragraph 4.4.3.1.
4.4.3.4.1 The lights are spaced across the entire taxiway, including fillets, holding bays, etc. If it is possible to meet paragraph 4.4.3.1 by allowing the reference fixture to be moved any amount laterally, then that method should be used.
4.4.3.4.2 Otherwise, the lights must be spaced as uniformly as possible with a minimum spacing of 8 ft (2.4 m) and a maximum of 13 ft (4 m).
4.4.4 Light Beam Orientation for In-Pavement RGLs. The L-868 bases for in-pavement RGLs must be installed such that a line through one pair of bolt holes on opposite sides of the base is parallel to the runway holding position marking.
4.4.4.1 Each light fixture is installed so that the light beam faces away from the runway and is perpendicular to the runway holding position marking within a tolerance of ±1 degree.
4.4.4.2 For some pavement configurations, it may be necessary to orient the lights at some angle to the marking.
4.4.4.3 To accomplish proper light fixture orientation, install a 12-bolt light base (see AC 150/5345-42 for additional information) using the above
procedure; this allows the light fixtures to be adjusted 30 degrees left or right, as required.
4.4.4.4 See Figure A-52 for typical examples of various orientations.
4.4.5 Location of Elevated RGLs. Elevated RGLs are collocated with the runway holding position marking and are normally installed on each side of the taxiway.
4.4.5.1 The distance from the defined taxiway edge to the near side of an installed light fixture must be 10 to 17 ft (3 to 5 m).
4.4.5.2 To avoid undesirable spots, the RGL may be moved up to 10 ft (3 m) farther from the runway, but may not be moved toward the runway (see Figure A-51).
4.4.5.3 If a stop bar is installed at the runway holding position, the elevated RGL must be located at least 3 ft, 6 inches (1 m) outboard of the elevated stop bar light.
4.4.5.4 The RGL must not interfere with the readability of the runway holding position sign, obscure any taxiway edge lights, or interfere with other airport lighting.
4.4.6 Light Beam Orientation for Elevated RGLs. Orient RGLs to maximize the visibility of the light to pilots of aircraft approaching the runway holding position.
4.4.6.1 Aim the center of the light beam toward the aircraft cockpit when the aircraft is between 150 ft (45 m) and 200 ft (60 m) from the holding position, along the predominant taxi path to the holding position.
4.4.6.2 Set the vertical aiming angle between 5 degrees and 10 degrees above the horizontal.
4.4.6.3 Aim of the lights such that the steady-burning intensity at all viewing positions between 150 ft (45 m) and 200 ft (60 m) from the holding position is at least 300 candela (cd) for an incandescent lamp when operated at the highest intensity step. (Refer to AC 150/5345-46 for specifications and photometrics of the L-804 RGL fixture.)
4.4.6.4 If these criteria cannot be met for all taxi paths to the holding position, consider using multiple fixtures aimed to adequately cover the different taxi paths.
4.4.6.4.1 Use in-pavement fixtures to increase the viewing coverage, or aim the single fixtures on each side of the holding position to optimize the illumination of the predominant taxi path.
Chapter 4 TAXIWAY LIGHTING SYSTEMS › 4.5. Runway Stop Bar.
4.5. Runway Stop Bar.
4.5.1 General. A stop bar consists of a row of unidirectional in-pavement red lights and an elevated red light on each side of the taxiway.
4.5.2 Location of In-Pavement Stop Bar Lights. In-pavement stop bar lights are centered on an imaginary line which is parallel to, and 2 ft (0.6 m) from, the center of the fixture and the holding side of the runway holding position marking, per Figure A-51.
4.5.2.1 The lights may vary from this imaginary line up to ±2 inches (±50 mm) in a direction perpendicular to the holding position marking. Holding position marking locations are described in AC 150/5340-1.
4.5.2.2 If a conflict with rigid pavement joints occurs, move both the runway holding position marking and the stop bar lights away from the runway the minimum distance required to resolve the conflict. If other markings (e.g., geographical position markings) are installed, they must be moved as well.
4.5.2.3 Lateral Spacing - Preferred Method. 4.5.2.3.1 The lights are spaced across the entire taxiway, including fillets, holding bays, etc., at intervals of 9 ft, 10 inches (3 m), ±2 inches (±50 mm), center-to-center, per Figure A-51.
4.5.2.3.2 The lights are spaced in relation to a reference fixture which is installed inline (longitudinally) with existing or planned taxiway centerline lights. However, it is not intended that the reference fixture replace a taxiway centerline light.
4.5.2.3.3 If a conflict between the reference fixture and a centerline light occurs, the reference fixture takes the place of an existing centerline light and a new centerline light must be installed per the criteria in paragraph 4.3.3.
4.5.2.3.4 If the holding position marking is intersected by multiple taxiway centerline markings, the reference fixture must be set at the centerline that is used most.
4.5.2.3.5 If a fixture’s outboard edge falls at a point less than 2 ft (0.6 m) from the defined edge of the taxiway marking, the outboard edge of the taxiway marking may be omitted.
4.5.2.3.6 Individual fixtures may be moved laterally a maximum of ±1 foot (305 mm) to avoid undesirable spots, e.g., conduit, etc.
Note: If undesirable spots cannot be avoided in this way, fixtures may be moved no more than 2 ft (0.6 m) using the following alternate method.
4.5.2.4 Lateral Spacing - Alternate Method. 4.5.2.4.1 The following alternate method of spacing the lights should be followed if it is not possible to meet the preferred method per paragraph 4.5.2.1.
1. The lights are spaced across the entire taxiway, including fillets, holding bays, etc. If it is possible to meet paragraph 4.5.2.1 by allowing the reference fixture to be moved any amount laterally, then that method should be used.
2. Otherwise, the lights should be spaced as uniformly as possible with a minimum spacing of 8 ft (2.4 m) and a maximum spacing of 13 ft (4 m).
4.5.3 Light Beam Orientation for In-Pavement Stop Bar Lights. The L-868 bases for in-pavement stop bar lights must be installed such that a line through one pair of bolt holes on opposite sides of the base is parallel to the runway holding position marking.
4.5.3.1 Each light fixture is installed so that the axis of the light beam faces away from the runway and is perpendicular to the marking with a tolerance of ±1 degree.
4.5.3.2 In some instances, it may be necessary to aim the lights at some angle to the marking. To accomplish this, install a 12-bolt base using the above procedure.
4.5.3.3 This allows the light fixtures to be adjusted 30 degrees left or right, as required. See Figure A-52 for typical examples.
4.5.4 Location of Elevated Stop Bar Lights. Elevated stop bar lights are installed in line with the in-pavement stop bar lights on each side of the taxiway.
4.5.4.1 They are located not more than 10 ft (3 m) from the defined edge of the taxiway.
4.5.4.2 For airports that perform any snow removal operations, if taxiway edge lights are present, the elevated stop bar light should not be installed closer to the taxiway edge than the line of taxiway edge lights. This is to help prevent the elevated stop bar light from being struck by snow removal equipment.
4.5.4.3 To avoid conflicts with taxiway edge lights or undesirable spots, the elevated stop bar lights may be moved up to 10 ft (3 m) away from the runway, but may not be moved toward the runway. See Figure A-51.
4.5.5 Light Beam Orientation for Elevated Stop Bar Lights. Elevated stop bar lights should be oriented to enhance conspicuity of the light by pilots of aircraft approaching the runway holding position.
Chapter 4 TAXIWAY LIGHTING SYSTEMS › 4.7. Clearance Bar Configuration.
4.5.5.1 Aim the lights such that the axis of the light beams intersects the primary taxiway centerline between 120 ft (37 m) and 170 ft (52 m) from the holding position.
4.5.5.2 Set the vertical aiming angle between 5 degrees and 10 degrees above the horizontal. Specify the aiming of the lights such that the axis of the light beams intersects the primary taxiway centerline between 120 ft (37 m) and 170 ft (52 m) from the holding position.
4.6. Combination In-Pavement Stop Bar and RGLs. At the airport’s option, combination in-pavement stop bar and RGL lights may be installed in lieu of standard in-pavement stop bar fixtures.
4.6.1 This option allows for the provision of in-pavement RGLs above 1,200 ft (365 m) RVR and a stop bar below 1,200 ft (365 m) RVR for a given location. (A typical application includes taxiways >150 ft (45 m) wide which lie on a designated low visibility taxi route for operations below 600 ft (183 m) RVR.)
4.6.2 Design the circuit so that the yellow and red lights cannot both be “on” at the same time (applies only to in-pavement fixture L-852G/S).
4.6.3 Install combination stop bar/RGL fixtures in the same location and with the same light beam orientation as in-pavement stop bars. See Figure A-51 for additional information.
4.6.4 Refer to AC 120-57 for further criteria on the application of combination stop bar/RGLs below 1,200 ft (365 m) RVR.
Note: Elevated RGLs may be operated continuously regardless of RVR condition or stop bar use to enhance safety and awareness of the runway environment.
4.7. Clearance Bar Configuration.
4.7.1 General. A clearance bar consists of a row of three in-pavement yellow lights that indicate a low visibility hold point.
4.7.1.1 The light fixtures are normally unidirectional but may be bidirectional if the hold point is intended to be used in either one or two directions. Refer to AC 120-57 for criteria on the application of clearance bars.
4.7.1.2 With the following exceptions, install clearance bars (without regard to visibility) at a taxiway intersection with non-standard fillets or where the taxiway centerline lights do not follow curves at intersections per Figure A-44. Clearance bars installed for this purpose consist of unidirectional fixtures.
4.7.1.3 Clearance bars may be omitted if taxiway edge lights are installed at the intersection per paragraph 2.5.3.
4.7.1.4 Clearance bars at a “T” or “+” shaped taxiway/taxiway intersection may be replaced or supplemented by an omnidirectional yellow taxiway intersection light (L-852E or F, as appropriate) installed near the intersection of the centerline markings, if the angle between the centerlines of any two adjacent segments of the pavement is 90 degrees ±10 degrees.
4.7.1.5 The clearance bar located on an exit taxiway may be omitted if it would be located before, or within 200 ft (61 m) beyond, a runway holding position (as viewed while exiting the runway).
4.7.2 Location of a Clearance Bar Installed at a Low Visibility Hold Point. A low visibility hold point consists of an intermediate holding position marking, a geographic position marking, and a clearance bar.
4.7.2.1 Hold points are not necessarily located at taxiway/taxiway intersections.
4.7.2.2 Center in-pavement clearance bar lights on an imaginary line that is parallel to, and 2 ft (0.6 m) from, the holding side of the taxiway/taxiway holding position marking, per Figure A-53.
4.7.2.3 The lights may vary from this imaginary line by up to ±2 inches (±50 mm) (perpendicular to the holding position marking).
4.7.2.4 If a conflict occurs with rigid pavement joints or other undesirable areas, move the taxiway/taxiway holding position marking, geographic position marking, and the clearance bar longitudinally any amount necessary to resolve the conflict.
4.7.2.5 If the hold point is located at a taxiway/taxiway intersection, move all of the aforementioned items away from the intersecting taxiway the minimum distance necessary to resolve the conflict. If a conflict occurs between the center fixture in the clearance bar and a taxiway centerline light, the center light fixture takes the place of an existing taxiway centerline light, and a new centerline light must be installed per the criteria in paragraph 4.3.3.
4.7.3 Location of a Clearance Bar Installed at a Taxiway Intersection. A clearance bar installed at a taxiway intersection is located per the criteria in paragraph 4.7.2 if that location is established as a hold point and taxiway/taxiway holding position markings are present. Otherwise, locate the clearance bar in the same manner as if the holding position marking were present. This allows room for the possible future installation of the marking.
Chapter 4 TAXIWAY LIGHTING SYSTEMS › 4.8. Design.
Note: Taxiway/taxiway holding position marking locations are described in AC 150/5340-1.
4.7.3.1 Lateral Spacing. Install the center light of the clearance bar in line with existing or planned taxiway centerline lights. Install the two remaining lights outboard of the center fixture on 5 foot (1.5 m) intervals, center-to-center, per Figure A-44, Clearance Bar Detail A. The outboard fixtures may be moved laterally a maximum of ±1 foot (305 mm) to avoid undesirable spots, e.g., conduit, etc.
4.7.4 Light Beam Orientation for Clearance Bars. The axis of the light beam for each fixture must be parallel to the centerline of the designated taxiway path with a tolerance of ±1 degree.
4.8. Design.
4.8.1 General. The installation of in-pavement L-868 light bases and conduit should be done, if possible, while the pavement is under construction or when an overlay is made. Installation of light bases after paving is very costly and requires a lengthy shutdown of the taxiway or runway.
4.8.2 Layout. Develop a design drawing prior to construction that shows the dimensional layout of each lighting system to be installed. Correlate this design with current airport drawings to utilize available ducts and utilities and to avoid conflict with existing or planned facilities. Do not exceed 40% conduit fill, per the conduit fill tables in NFPA 70, NEC. Also, correlate this design with the type of existing equipment fed by the existing cable system to minimize the effects of EMI.
4.8.3 In-Pavement Light Fixtures and Electrical Cables. Design each in-pavement lighting system for one of the conditions listed in Chapter 10 and Chapter 11.
4.8.4 General Circuit Design and Control Concept.
4.8.4.1 For Airports That Use RGLs and/or Stop bars to Prevent Runway Incursions in Visibility at or Above 1200 (365 m) RVR. Each of these systems should be on dedicated circuits (see paragraphs 4.8.6.1.1 and 4.8.7.3.1.
4.8.4.2 For Airports with Operations Below 1,200 ft (365 m) RVR. As the weather deteriorates below 1,200 ft (365 m) RVR, SMGCS procedures to be in effect will activate the “below 1,200 ft RVR” system on the airport lighting control panel.
4.8.4.2.1 All low visibility lighting systems necessary for below 1,200 ft (365 m) RVR operations will be turned on, per AC 120-57.
4.8.4.2.2 Turn off taxiway centerline lights and edge lights on taxiways that are not designated as low visibility taxi routes.
4.8.4.2.3 For airports with operations below 600 ft (183 m) RVR, see AC 120-57 paragraph 8b(2)(a), for operations below 600 ft (183 m) RVR.
4.8.5 Taxiway Centerline Lighting and Clearance Bar Systems.
4.8.5.1 Fixture Selection. Install L-852C (narrow beam), L-852D (wide beam), and L-852F (omnidirectional) fixtures on taxiways that are designated as low visibility taxi routes below 1,200 ft (365 m) RVR per AC 120-57.
4.8.5.1.1 Where the RVR ≥1200 ft, install L-852A (narrow beam), L-852B (wide beam), and L-852E (omnidirectional) taxiway centerline fixtures.
Continue reading ↓ 120 of 574 passages shown