Radar Vectors
FAA Order Current Issued Nov 6, 2016 AJF-0 490 pages Copy saved Nov 18, 2026

Order 8200.1D United States Standard Flight Inspection Manual with CHG 1 and 2

This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1D; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated April 15, 2015.

Official source ↗ Open PDF

Text read by OCR from a scanned file (12 of 490 pages). Check the original, as some words may be misread.

Change_Notice_8200.1D CHG_2 › 4. Explanation of Policy Changes.

Distribution: Electronic Initiated By: AJF-0

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

ORDER 8200.1D CHG 2

National Policy

Effective Date:

09/20/2024

SUBJ: United States Standard Flight Inspection Manual

1. Purpose. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1D Change 2; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated June 7, 2021.

2. Who this change affects. FAA and DOD personnel involved in the flight inspection and certification of air navigation services.

3. Disposition of Transmittal Paragraph. Retain this transmittal sheet until this Directive is canceled by a new Directive.

4. Explanation of Policy Changes. This order has been reformatted and updated to remove canceled FAA Order and Form references and to reflect the current organizational structure. Paragraph and item reference hyperlinks have been updated as necessary. Chapter 16, Microwave Landing System (MLS) and all subsequent references to MLS and Mobile Microwave Landing System (MMLS) have been removed from this order. Chapter 14 was retitled to Surveillance. Chapter 17 Local Area Augmentation System (LAAS) was replaced with Ground Based Augmentation System (GBAS). The content of Chapters 4, 11, and Appendices A and C were changed.

Change_Notice_8200.1D CHG_2 › Dated

PAGE CHANGE CONTROL CHART

Remove Pages Dated Insert Pages Dated

Page i thru iv 04/15/15 Page i thru xx 9/20/24

Page 1-1 thru 1-4 04/15/15 Page 1-1 thru 1-3 9/20/24

Page 4-1 thru 4-3, 4-8 thru 4-10, 4-13, 04/15/15 Page 4-1 thru 4-3, 4-8 thru 4-10, 4-13, 9/20/24

and 4-15. and 4-15

Page 5-4 thru 5-5 04/15/15 Page 5-4 thru 5-5 9/20/24

Page 6-22 04/15/15 Page 6-16 9/20/24

Page 11-7 thru 11-9, 11-14, 11-19, and 04/15/15 Page 11-7 thru 11-9, 11-14, 11-19, and 9/20/24

11-20 04/15/15 11-20

Page 14-1, 14-6, 14-8, 14-17, 14-18, 04/15/15 Page 14-1, 14-8, 14-18, 14-22, 14-40, 9/20/24

14-22, 14-40, and 14-43 and 14-43

Page 15-77 04/15/15 Page 15-77 9/20/24

Page 16-1 thru 16-39 11/06/16 Page 16-1 9/20/24

Page 17-1 thru 17-18 11/06/16 Page 17-1 thru 17-24 9/20/24

Page 23-4 04/15/15 Page 23-4

Page 24-10 and 24-11 04/15/15 Page 24-10 and 24-11

Page 25-1 thru 25-3 9/20/24

Appendix A-4 thru A-9, A-11, A-12, 04/15/15 Appendix A-4 thru A-9, A-11, A-12, A-15, 9/20/24

A-15, A-17 thru A-19, A-23 A-17 thru A-19, A-23 thru A-25,

thru A-25, A-28, A-29, A-40, A-28, A-29, A-40, A-41, A-43,

A-41, A-43, A-47 thru A-50, A-47 thru A-51

and A-54

Appendix B-6 Appendix B-6

Appendix C-9 thru C-11 04/15/15 Appendix C-9 thru C-19 9/20/24

Appendix D-2 04/15/15 Appendix D-2 9/20/24

Appendix G-1 thru G-3 04/15/15 Appendix G-1 9/20/24

Randa A. Hayes Acting Vice President, Flight Program Operations Flight Program Executive

04/15/15 9/20/24

9/20/24 9/20/24

09/20/2024 8200.1D CHG 2

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 1 to

8200.1D

11/06/16

SUBJ: United States Standard Flight Inspection Manual

1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1D; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated April 15, 2015.

2. Audience. Air Traffic Organization Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Field Offices and crewmembers in Flight Inspection Team (AJW-333); Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees.

3. Where Can I Find This Change? Go to http://www.faa.gov/regulations_policies/orders_notices/#browseTopics. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

4. Explanation of Policy Changes. Flight Inspection Support Subteam (AJW-3331) has made numerous revisions to FAA Order 8200.1D, United States Standard Flight Inspection Manual, Chapter 14 “Surveillance.” Impending limitations to the aircraft transponder systems used during flight inspection drove the need to revise this chapter. Therefore, Flight Inspection Support Subteam coordinated with the NAS Engineering Group, Radar Systems Team (AJW-147) to discuss the limitations, resulting in updates to the Surveillance Radar/ATCRBS inspection checklists.

Additionally, Flight Inspection Support Subteam took the opportunity to edit the entire chapter. The plainlanguage editorial revisions improve readability and clarify flight inspection guidance. The PAR tolerance table and associated inspection processes were revised, providing clearer guidance to inspection crews.

a. Technical Revisions: The following revisions include flight inspection guidance updates as well as checklist and tolerance revisions.

(1) Paragraph 14.3.d.(3). Guidance was added to ensure each published ASR approach procedure is inspected when changes to the primary or secondary radar power or tilt have been made.

(2) Paragraph 14.4. Revised the Surveillance checklist to accommodate the transponder limitations. All FI Transponder Settings were changed to either “OFF/OFF” or “ON/ON,” and the “OFF/ON” combination has been removed. Revisions are evidenced with a gray background.

- Orientation: FI Transponder Setting changed from OFF/ON to OFF/OFF - Tilt: Added Note 4 reference. Changed FI Transponder Setting from OFF/ON to ON/ON. - Primary Radar Optimization: Added Note 3 & 4 references. - ATCRBS Power Optimization: Added Note 3 & 4 references. Removed Note 1 reference from Commissioning inspection and Diff Type Antenna. Changed FI Transponder Setting from OFF/ON to ON/ON.

- SLS/ISLS: Added Note 4 reference. Changed FI Transponder Setting from OFF/ON to OFF/OFF. - Modes/Codes: Changed FI Transponder Setting from OFF/ON to OFF/OFF. - GTC/STC: Added Note 4 reference. - Vertical Coverage: Deleted “Above 15,000 ft MSL” FI Transponder Setting variance. All altitudes will be inspected with the FI Transponder Setting ON/ON. - Horiz Screening: Changed FI Transponder Setting from OFF/ON to ON/ON. - Airways/Route Coverage: Note 1 now applies to all items in this row, instead of just the commissioning requirement. Changed FI Transponder Setting from OFF/ON to ON/ON. - Fix/Map Acc: Added Note 4 reference. Changed FI Transponder Setting from OFF/ON to OFF/OFF. - Fixed Target Ident: Added Note 4 reference. Changed FI Transponder Setting from OFF/ON to OFF/OFF. - ASR Approach: Changed name from “Surveillance Apch” to “ASR Approach.” Added Note 1 and 3 references. Changed FI Transponder Setting from OFF/ON to OFF/OFF. - Note 2: Reworded for clarity - Note 3: Added requirement to inspect ASR approaches using a flight inspection aircraft following power or tilt adjustments. - Note 4: Added note. Targets-of-opportunity may be used to accomplish various inspection items.

(3) Paragraph 14.5.e.(2). Added/changed the guidance: “If the tilt angle changes during the radar inspection, each previously-inspected item must be re-inspected using the new tilt angle. Additionally, with an increase in antenna tilt, perform an ATCRBS power optimization check. Engineering personnel may use targets-of-opportunity to optimize a previously-commissioned radar system following a tilt change, but may request a flight inspection aircraft. Changes to the primary or secondary radar tilt or power require the inspection of each published ASR approach procedure using a flight inspection aircraft.”

(4) Paragraph 14.5.f.(2). Added guidance, “Changes to the primary or secondary radar power or tilt require the inspection of each published ASR approach procedure using a flight inspection aircraft.”

(5) Paragraph 14.5.g.(3). Deleted references to Magnetron/Amplitron Systems; ARSR- 1, -2, and -3; the Note below the table.

(6) Paragraph 14.5.g.(4). Added guidance, “Vertical coverage, whether verified by a flight inspection aircraft or using targets-of-opportunity, must be checked using the power level established by the ATCRBS Power Optimization procedure. The beacon must be commissioned at this power level, plus 1 dB.”

(7) Paragraph 14.5.k. Renamed paragraph from “Surveillance Approaches” to “ASR Approach Procedures.” Added a reference to Chapter 6, as well as primary or secondary radar tilt or power change guidance.

Page 2

(8) Paragraph 14.5.o.(2). Added guidance, “ATCRBS power optimization is required with an increase in antenna tilt, and may be accomplished using targets-of-opportunity. Changes to the primary or secondary radar tilt or power require the inspection of each published ASR approach procedure using a flight inspection aircraft.”

(9) Paragraph 14.7. Revised the WAM checklist Fix/Map Accuracy transponder setting from “OFF/ON” to “OFF/OFF.” Notes 2, 3, and 4 were edited for readability.

(10) Paragraph 14.17.a.(1), (2), and (3). Revised the course alignment measurement methods. Added the following: “Azimuth alignment measurements between decision height and runway threshold are limited to the Visual Method.”

(11) Paragraph 14.17.b. Reworded the paragraph for clarification and added guidance limiting alignment measurements to the Visual Method between 0.8 nm and runway threshold.

(12) Paragraph 14.19. Revised the Azimuth Course Alignment (Along-Track) tolerance from “The greater of 30 ft or 0.6% of the aircraft to PAR antenna distance, referenced to runway centerline” to “Greater of 30 ft or 0.34° from runway centerline; use the runway point of intercept as the azimuth point of origin.” Deleted Note (1), and renumbered the Notes.

b. Editorial Revisions: The following editorial revisions use plain language to improve readability and clarity. These items do not change flight inspection guidance and do not affect NAS Safety.

(1) Chapter Title. Changed from “Surveillance and Reports” to “Surveillance.” The term “and Reports” does not apply to this Order, since FAA Order 8240.36N governs flight inspection reports.

(2) Paragraph 14.1. Reworded for clarity.

(3) Paragraph 14.1.a. Changed paragraph name from “Surveillance (Primary) Radar” to “Primary Radar”; reworded paragraph for clarity.

(4) Paragraph 14.1.b. Changed paragraph name from “ATCRBS (Secondary) Radar” to “Secondary Radar”; reworded paragraph for clarity.

(5) Paragraph 14.1.d. Added Mode-S information; reworded paragraph for clarity.

(6) Paragraph 14.2. Changed paragraph name from “Preflight Requirements/Inspection Plan” to “Flight Inspection Planning”; reworded paragraph for clarity. Corrected JO 6300.13 reference.

(7) Paragraph 14.2.a. Reworded paragraph and sub-paragraphs for clarity. Changed sub-paragraph (1), (2), (3) and (7) names, eliminating prepositions.

(8) Paragraph 14.2.b.(4). Replaced “ATCRBS” with “secondary”. Reworded for clarity. Note (1) added to table.

(9) Paragraph 14.2.c. Deleted paragraph. Moved contents and consolidated into paragraph 5.t.

(10) Paragraph 14.3. Changed paragraph name from “Flight Inspection Procedures” to “Surveillance Radar Flight Inspections.”

Page 3

(11) Paragraph 14.3.a. Reworded for readability and clarity. Added “losing two-way radio communication” section to the end of this paragraph.

(12) Paragraph 14.3.c. Reworded for readability and clarity. Added reference to Chapter 4, Table 4-1.

(13) Paragraph 14.3.d.(1). Reworded for clarity; used active voice.

(14) Paragraph 14.4. Changed paragraph and checklist names from “Surveillance Radar/ATCRBS Checklist” to “Surveillance Radar Checklist.”

(15) Paragraph 14.5. Changed paragraph name from “Detailed Procedures” to “Surveillance Radar Detailed Procedures.”

(16) Paragraph 14.5.a. Reworded for clarity.

(17) Paragraph 14.5.d.(1) and (3). Reworded for clarity.

(18) Paragraph 14.5.g.(1). Reworded for clarity.

(19) Paragraph 14.5.g.(4). Reworded paragraph and Note for clarity.

(20) Paragraph 14.5.g.(4).(d) and (e). Reworded for clarity.

(21) Paragraph 14.5.h.(2). Reworded for clarity.

(22) Paragraph 14.5.i.(1). Reworded for clarity.

(23) Paragraph 14.5.j.(1). Reworded for clarity.

(24) Paragraph 14.5.k. Changed name from “Surveillance Approaches” to “ASR Approach Procedures.”

(25) Paragraph 14.5.k. Reworded entire paragraph for clarity.

(26) Paragraph 14.5.m.(2). Reworded for clarity.

(27) Paragraph 14.5.n. Removed “ATCRBS” from paragraph name. Updated paragraph for clarity. Moved “Do not use codes 7500, 7600, and 7700…” to paragraph 5.n.(2).

(28) Paragraph 14.5.o. Reworded paragraph and NOTE for clarity.

(29) Paragraph 14.5.p. Removed “ATCRBS” from paragraph title, and reworded entire paragraph for clarity and readability.

(30) Paragraph 14.5.s. Reworded for clarity.

(31) Paragraph 14.5.t. Changed name to MSAW. Acronym was already defined in paragraph 1.c. Entire paragraph reworded to incorporate information deleted in paragraph 2.c. Flight inspection guidance remains unchanged.

(32) Paragraph 14.6. Changed name to “WAM Flight Inspection Procedures” since WAM has already been defined in the Section 1 title.

Page 4

(33) Paragraph 14.7. Changed name from “Wide Area Multilateration Checklist” to “WAM Checklist.” Reworded paragraph for clarity. Corrected transponder sensitivity in NOTE 6 from -66 dB to -69 dBm, which is the correct value based on Engineering Services analysis of the US WAM systems.

(34) Paragraph 14.8.b. Updated paragraph for readability and clarity.

(35) Paragraph 14.8.d.(2). Corrected transponder sensitivity from -66 dB to -69 dBm, which is the correct value based on Engineering Services analysis of the US WAM systems.

(36) Paragraph 14.8.e.(2)(a). Corrected transponder sensitivity from -66 dB to -69 dBm, which is the correct value based on Engineering Services analysis of the US WAM systems.

(37) Paragraph 14.8.h. Moved “Do not use codes 7500, 7600, and 7700…” from (1) to the end of paragraph (2) and reworded for clarity.

(38) Paragraph 14.8.k. Added verbiage for readability and clarity. Flight inspection guidance has not changed.

(39) Paragraph 14.8.m.(2)(a). Corrected transponder sensitivity from -66 dB to -69 dBm, which is the correct value based on Engineering Services analysis of the US WAM systems.

(40) Paragraph 14.10. Change the reference abeam “Communications” to 14.5.q and 14.8.i., instead of “Chapter 8”. Change the Tolerance Limit to “See Chapter 8, Paragraph 8.5.”

(41) Paragraph 14.13. Introduction reworded for clarity and readability.

(42) Paragraph 14.15. Changed name from “Flight Inspection Specifications” to “PAR Flight Inspections.” Title fits the convention used throughout this Order. Updated subparagraphs to fit with the Order convention, specifically “General, Commissioning Inspections, Periodic Inspections, and Special Inspections.” General information is provided for readability and clarity. Flight inspection guidance was not changed.

(43) Paragraph 14.15.d. Edited sub-paragraph wording for clarity.

(44) Paragraph 14.16. Reworded paragraph for clarity. Checklist Legend updated for readability. Added “A” Cursor, AZ, Channel, CP, EL, GP, LP, and MTI/MTD with definitions for clarity.

(45) Paragraph 14.16.d. Changed name of checklist to “MPN-25/ GCA(PAR)- 2000/FPN-68, TPN-31 (31/A), FPN-67”. FPN-68 is the same system as the GCA(PAR)-2000. Reworded paragraph for readability and clarity. Checklist Note 6 changed to 8, and added new notes 6 and 7. New notes are informational, and do not change the flight inspection guidance.

(46) Paragraph 14.17. Reworded for clarity.

(47) Paragraph 14.17.a. Changed name from “Course Alignment and Coverage (Azimuth)” to “Azimuth Course Alignment.” Coverage guidance is located in paragraphs 17.e. and 17.f.

(48) Paragraph 14.17.c. Reworded for clarity.

Page 5

(49) Paragraph 14.17.d. Reworded for clarity. Added reference to Chapter 24 and replaced “See Paragraph 14.17.e, Note” with the actual note contained in that paragraph.

(50) Paragraph 14.17.e. Changed name from “Usable Distance” to “Distance Coverage.” Reworded paragraph for clarity.

(51) Paragraph 14.17.f. Reworded for clarity.

(52) Paragraph 14.17.g.(1). Reworded for clarity.

(53) Paragraph 14.17.g. Changed name from “Glidepath Alignment” to “Glidepath Angle & Alignment.” Reworded for clarity.

(54) Paragraph 14.17.h. Reworded for clarity.

(55) Paragraph 14.17.h.(1) and (2). Reworded for clarity.

(56) Paragraph 14.17.i. Reworded for clarity.

(57) Paragraph 14.17.j. Reworded for clarity. Added GBAS GLS and WAAS LPV approach types (both precision) to the list of requiring PAR coincidence.

(58) Paragraph 14.17.k. Reworded for clarity.

PAGE CONTROL CHART

REMOVE

PAGES

DATED INSERT

PAGES

DATED

Page 14-i thru 14-46 04/15/2015 Page 14-i thru 14-48 11/06/2016

David H. Boulter Director, Flight Program Operations, AJW-3 Flight Program Executive

Page 6

Order 8200.1D with Change 1 and 2

Distribution: Electronic Initiated By: AJF-0

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

ORDER

8200.1D

National Policy Effective date:

04/15/2015

SUBJ: United States Standard Flight Inspection Manual (USSFIM)

This order prescribes standardized procedures for flight inspection of air navigation services. It is not intended as authorization for any agency to assume flight inspection authority over any group of services which are not now under its jurisdiction. Similarly, it carries no designation of responsibility within any agency unless such has been so designated in its usual procedural manner, such as general orders, regulations, etc.

This order is directive upon all personnel charged with the responsibility for execution of the flight inspection mission when such personnel or organization is so designated by its agency. Compliance with this order, however, is not a substitute for common sense and sound judgement. Nothing in this order will be construed to relieve flight inspection crews or supervisory personnel of the responsibility of exercising initiative in the execution of the mission, or from taking such emergency action as the situation warrants.

The Federal Aviation Administration (FAA) will coordinate and provide approved changes to this order by means of a page revision method. Revised pages will be transmitted by a Federal Aviation Administration Change or Notice. Recommendations concerning changes or additions to the subject material are welcomed and should be forwarded to one of the following addresses:

US Army:

Commander, US Army Aeronautical Services Agency 9325 Gunston Rd., Suite N319 Ft. Belvoir, VA 22060-5582

US Navy:

Director, Naval Airspace and Air Traffic Control Standards and Evaluation Agency (OPNAV N980A) 2000 Navy Pentagon (5D453) Washington, DC 20350-2000

US Air Force:

HQ USAF/A3OJ Bases, Ranges & Airspace Division 1480 Air Force Pentagon Suite 5D756 Washington, DC 20330-1480

Distribution: Electronic Initiated By: AJF-0

FAA:

Vice President, Flight Program Operations PO Box 20582 Oklahoma City, OK 73125

This order of Flight Inspection Procedures has been officially approved by:

US Army: Headquarters, Department of the Army, Deputy Chief of Staff, G-3/5/7

US Navy: Headquarters, US Navy, Deputy Chief of Naval Operations, N3/N5

US Air Force: HQ, Department of the Air Force, Deputy Chief of Staff for Operations, A3

FAA: Vice President, Flight Program Operations

Randa Hayes Vice President (A) Flight Program Operations

09/20/2024 8200.1D CHG 2

Table of Contents

Paragraph Page

i

Chapter 1. General Information … 1-1

1. Purpose of This Order … 1-1

2. Audience … 1-1

3. Where to Find This Order … 1-1

4. What This Order Cancels … 1-1

5. Explanation of Policy Changes … 1-1 a. Chapter 4: … 1-1 b. Chapter 5: … 1-1 c. Chapter 11: … 1-1 d. Chapter 14: … 1-1 e. Chapter 15: … 1-1 f. Appendix A: … 1-1 g. Appendix C: … 1-1

Chapter 2. Flight Inspection Crew Authority and Responsibilities … 2-1

1. Authority … 2-1

2. Responsibility … 2-1

Chapter 3. Special Requirements … 3-1

1. Introduction … 3-1

2. Aircraft … 3-1

3. Flight Inspection Crewmembers … 3-1

4. Airborne and Ground Support Equipment … 3-1

Chapter 4. Flight Inspection Types, Priorities, Intervals, Procedures … 4-1

Section 1. Types and Priorities of Flight Inspections … 4-1

1. Introduction … 4-1

2. Site Evaluation … 4-1

3. Commissioning … 4-1

4. Periodic … 4-1

5. Special Flight Inspections … 4-1 a. USAF Air Traffic Control and Landing System (ATCALS) evaluation

requirements … 4-1 b. USAF Deployable (Mobile) ATCALS (DATCALS) … 4-1 c. Unapproved Facilities … 4-2 d. Facility Removal and Replacement … 4-2 e. New or Modified Equipment Testing … 4-2

Table of Contents

Paragraph Page

ii

f. After Accident … 4-2 g. Reconfiguration … 4-3 h. Inspections of Shipboard TACAN(s) … 4-3

6. Surveillance … 4-3 a. Surveillance of Aeronautical Services … 4-3 b. Inspections … 4-3 c. Reports … 4-4

7. Priorities of Flight Inspection … 4-4

Section 2. Frequency of Periodic Flight Inspection … 4-6

8. Introduction … 4-6 a. Intervals … 4-6 b. Scheduling … 4-6

9. Extension of Services Overdue Periodic Inspection … 4-7

10. NAVAIDS Temporarily Out-of-Service … 4-7

11. Rho-Theta Receiver Checkpoints … 4-8

12. Periodic Flight Inspection Intervals … 4-8 a. Commissioning … 4-8 b. Specials Other Than Reconfigurations … 4-8 c. Reconfiguration of Precision Approach Services … 4-8

13. ILS Monitor (or Reference) Intervals … 4-9

Section 3. General Flight Inspection Procedures … 4-10

14. Introduction … 4-10

15. Request for Flight Inspection … 4-10 a. Status of Equipment … 4-10 b. Notification … 4-10 c. Localizer Periodic Inspection Without Monitors … 4-10

16. Preflight Inspection Preparation … 4-10 a. Facilities Maintenance Personnel … 4-10 b. Flight personnel … 4-11

17. Flight Inspection … 4-11 a. Operator Proficiency … 4-11 b. Standby Equipment … 4-11 c. Standby Power … 4-12 d. On-Station Philosophy … 4-12 e. Restrictions … 4-12 f. Spectrum Engineering Services Restrictions … 4-12 g. Adjustments … 4-12 h. Incomplete Inspections … 4-12 i. Hazardous and Misleading Information (HMI) … 4-13

Table of Contents

Paragraph Page

iii

18. Analysis and Evaluation … 4-13 a. Data … 4-13 b. Recordings … 4-13 c. Alignment Convention … 4-14 d. System Evaluations … 4-14 e. Publications Review … 4-14

19. Post Flight Inspection … 4-14 a. Actions … 4-14 b. VFR Aeronautical Charts … 4-15

Chapter 5. Facility Status Classification, Notices to Air Missions (NOTAMs), Records, and Reports … 5-1

Section 1. Facility Status Classification and Notices to Air Missions (NOTAMs) … 5-1

1. Introduction … 5-1

2. Facility Status Classification … 5-1 a. International Facilities … 5-1 b. Facility Coverage in Limited Areas … 5-2

3. NOTAM(s) … 5-2 a. General … 5-2 b. Facility NOTAMS … 5-2 c. Instrument Flight Procedures … 5-2 d. Facilities Not Requiring NOTAM(s) … 5-2 e. Expanded Service Volume (ESV) Facilities … 5-2 f. Out-of-Tolerance Standby Equipment … 5-2 g. NOTAM(s) on Military Facilities (including ships) … 5-3 h. Preparation of NOTAM(s) … 5-3 i. Facility Restrictions … 5-3 j. NOTAM Examples … 5-4 k. Required Advisories for Local NOTAM(s) … 5-5

Section 2. Records and Reports … 5-6

4. Introduction … 5-6

5. Records … 5-6 a. General Information … 5-6 b. Facility Data Sheets … 5-6

6. Reports … 5-6 a. Military Facilities … 5-7 b. Reports … 5-7 c. VFR Aeronautical Chart field sheet … 5-7

Chapter 6. Flight Inspection and Flight Validation of Instrument Flight Procedures … 6-1

1. Introduction … 6-1

Table of Contents

Paragraph Page

iv

a. General … 6-1 b. Characteristics … 6-1 c. Data Accuracy and Integrity … 6-1 d. Inspector Authority … 6-2

2. Validation Process … 6-2 a. Preflight Validation … 6-3 b. Flight Validation … 6-3 c. Post-Flight Analysis … 6-3

3. Preflight Requirements … 6-3 a. Data and Procedure Package Requirements … 6-3 b. Review of the Procedure Package … 6-4 c. Simulator Evaluation … 6-5 d. Applicable Navigation System Support … 6-6 e. Obstacle Accuracy Verification … 6-6

4. Flight Inspection and Flight Validation Procedures … 6-6 a. General … 6-6 b. Checklist … 6-7 c. Obstacle Verification Evaluation … 6-8 d. Airways, Routes, and Terminal Route Segments … 6-12 e. Holding Patterns … 6-12 f. Standard Terminal Arrival Route (STAR) … 6-12 g. Standard Instrument Approach Procedures (SIAP) … 6-12 h. Flyability … 6-14 i. Departure Procedures, SID(s), and ODP(s) … 6-18 j. Air/Ground Communications … 6-18 k. Runway Markings, Lighting, and Supporting Infrastructure … 6-19 l. RADAR Coverage … 6-19 m. Charted Visual Approaches … 6-19 n. Maximum Authorized Altitudes (MAA) … 6-19 o. Periodic SIAP Reviews … 6-19

5. Analysis … 6-19 a. Cartographic Standards … 6-19 b. Night Evaluations … 6-19 c. Human Factors … 6-20

6. Tolerances … 6-21

Chapter 7. Lighting Systems … 7-1

Section 1. Visual Glide Slope Indicator (VGSI) … 7-1

1. Introduction … 7-1 a. Visual Approach Slope Indicator System (VASI) … 7-1 b. Precision Approach Path Indicator System (PAPI) … 7-3 c. Pulsating Visual Approach Slope Indicator System (PVASI) … 7-3

Table of Contents

Paragraph Page

v

d. T-VASI … 7-4 e. Helicopter Approach Path Indicator (HAPI) … 7-4 f. Tri-Color VASI … 7-4

2. Preflight Requirements … 7-4 a. Ground … 7-4 b. Air … 7-4 c. Installation Considerations … 7-5

3. Flight Inspection Procedures … 7-5 a. Checklist … 7-5 b. Detailed Procedures … 7-6

4. Analysis … 7-12

5. Tolerances … 7-12 a. Light Intensity … 7-12 b. Visual Glidepath Angle … 7-12 c. Angular Coverage … 7-13 d. Obstacle Clearance … 7-13 e. System Identification/Contrast … 7-13

6. Adjustments … 7-13

Section 2. Approach and Runway Lights … 7-23

7. Introduction … 7-23 a. Category I Approach Lighting System, Sequenced Flashers, (ALSF-1) … 7-23 b. Category II Approach Lighting System, Sequenced Flashers, (ALSF-2) .... 7-23 c. Sequenced Flashers for ALSF-1 and ALSF-2 … 7-24 d. Simplified Short Approach Lighting System (SSALS) … 7-24 e. Simplified Short Approach Lighting System with Sequenced Flashers (SSALF) … 7-24 f. Simplified Short Approach Light System with Runway Alignment Indicator Lights (SSALR) … 7-24 g. Medium Intensity Approach Lighting System (MALS) … 7-24 h. Medium Intensity Approach Lighting System with Sequenced Flashers

(MALSF) … 7-25 i. Medium Intensity Approach Lighting System with Runway Alignment Indicator Lights (MALSR) … 7-25 j. Omnidirectional Approach Lighting System (ODALS) … 7-25 k. Runway End Identifier Lights (REIL) … 7-25 l. Sequence Flashing Lights (SFL)/Runway Alignment Indicator Lights (RAIL) … 7-25

8. Pre-Flight Requirements … 7-26 a. Facilities Maintenance … 7-26 b. Air … 7-26

9. Flight Inspection Procedures … 7-26

Table of Contents

Paragraph Page

vi

a. Checklist … 7-26 b. Detailed Procedures … 7-26 c. Approach Light Systems … 7-27 d. Runway End Identifier Lights … 7-28

10. Flight Inspection Analysis … 7-28 a. Malfunctions … 7-28 b. Minima … 7-28

11. Tolerances … 7-28 a. Approach Lighting Systems, Runway Edge Lights, Touchdown Zone, and Runway Centerline Lights … 7-28 b. Runway End Identifier Lights (REIL) … 7-29

12. Adjustments … 7-30

Chapter 8. Communications … 8-1

Section 1. Ultra-High Frequency (UHF)/Very High Frequency (VHF) … 8-1

1. Introduction … 8-1

2. Preflight Requirements … 8-1

3. Flight Inspection Procedures … 8-1 a. Checklist … 8-1 b. Detailed Procedures … 8-2 c. Terminal Communications (TCOM) … 8-2 d. En route Communications (ECOM) … 8-2 e. Automatic Terminal Information Service (ATIS) … 8-2 f. Automated Weather Observing System (AWOS)/Automated Surface Aviation Observing System (ASOS) … 8-2 g. Transcribed Weather Broadcast (TWEB) … 8-3

4. Analysis … 8-3

5. Tolerances … 8-3 a. Maximum Recommended Coverage … 8-3 b. Local Requirements … 8-4 c. USAF air traffic control facilities … 8-4 d. Light Gun Requirements … 8-5

6. Adjustments … 8-5

Section 2. Direction Finding Stations (DF) … 8-6

7. Introduction … 8-6

8. Preflight Requirements … 8-6 a. Facilities Maintenance personnel … 8-6 b. Flight Personnel … 8-6

9. Flight Inspection Procedures … 8-7

Table of Contents

Paragraph Page

vii

a. Checklist … 8-7 b. Detailed Procedures … 8-7

10. Standby Equipment … 8-11

11. Tolerances … 8-11 a. Bearing Accuracy … 8-11 b. Coverage … 8-11 c. Communications … 8-11 d. Station Passage … 8-12 e. Controller Performance … 8-12 f. Standby Power … 8-12 g. Emergency Approaches … 8-12

12. Adjustments … 8-12

Chapter 9. Reserved … 9-1

Chapter 10. Reserved … 10-1

Chapter 11. Rho and Theta Systems … 11-1

Section 1. General … 11-1

1. Introduction … 11-1

2. Preflight Requirements … 11-1 a. Facilities Maintenance Personnel … 11-1 b. Flight Personnel … 11-1

3. Checklist … 11-1

Section 2. VHF Omnirange (VOR and TACAN/DME Flight Inspection Specifications

11-4

4. Flight Inspection Specification … 11-4 a. Reference Radial Check … 11-4 b. Monitor Reference Evaluation … 11-4 c. En Route Radials … 11-5 d. Intersection Radial/DME Fixes … 11-5 e. Terminal Radials/Fixes (Approach, Missed Approach) … 11-6 f. Orbit Evaluations … 11-7 g. Expanded Service Volumes (ESV(s)) … 11-9 h. Receiver Checkpoints … 11-10 i. Standby Transmitters … 11-10 j. Standby Power … 11-10 k. Associated Facilities … 11-11 l. Crossing Radials … 11-11

5. Analysis … 11-11 a. Identification (ID) … 11-11

Table of Contents

Paragraph Page

viii

b. Voice … 11-13 c. Sensing and Rotation … 11-13 d. Modulation Levels … 11-13 e. Polarization … 11-14 f. Frequency Interference … 11-14 g. TACAN Analysis … 11-15 h. Modulation Percentage 135 and 15 Hz … 11-15

6. Course Structure … 11-16 a. Roughness, scalloping, and bends … 11-16 b. To measure the amplitude of roughness and scalloping, … 11-16 c. Draw a third line equidistant … 11-17 d. A bend is similar to scalloping … 11-17 e. Application of Tolerances … 11-17

7. Signal Strength … 11-19

8. DME Coverage … 11-19

Section 3. Distance Measuring Equipment (DME) … 11-20

9. Introduction … 11-20

10. Distance Accuracy … 11-20

11. Identification … 11-20

12. Coverage … 11-20

Section 4. Shipboard TACAN … 11-21

13. Introduction … 11-21

14. Flight Inspection Specifications … 11-21 a. Scheduling … 11-21 b. Distance … 11-21 c. Radar … 11-21 d. Antennas … 11-21

15. Checklist … 11-21

16. Tolerance … 11-22

Section 5. VOR Test Facility … 11-23

17. Introduction … 11-23

18. Checklist … 11-23

19. Preflight Requirements … 11-23

20. Flight Inspection Specifications … 11-23 a. Frequency Interference (Spectrum Analysis) … 11-24 b. Identification … 11-24 c. Sensing … 11-24

Table of Contents

Paragraph Page

ix

d. Modulation Level … 11-24 e. VOT Reference Point … 11-24 f. Alignment … 11-25 g. Coverage … 11-25 h. Monitor … 11-26 i. Standby Power … 11-26

Section 6. Flight Inspection Tolerances … 11-27

21. Tolerances … 11-27 a. VOR Tolerances … 11-27 b. TACAN Tolerances … 11-31 c. DME Tolerances … 11-34 d. VOT Tolerances … 11-35

Chapter 12. Low and Medium Frequency Nondirectional Beacons (NDB) … 12-1

1. Introduction … 12-1 a. Classification … 12-1 b. Identifier … 12-1

2. Flight Inspection Qualifications … 12-2 a. Checklist … 12-2 b. Detailed Specifications … 12-2

3. Maintenance Actions Requiring Flight Inspection … 12-3

4. Flight Inspection Procedures … 12-3 a. Identification … 12-3 b. Voice … 12-4 c. Coverage Orbit … 12-4 d. Instrument Flight Procedures … 12-5 e. ESV … 12-5 f. Station Passage … 12-6 g. Standby Equipment … 12-6 h. Standby Power … 12-6 i. Special Inspections … 12-6

5. Reporting … 12-7

6. Flight Inspection Tolerances … 12-8 a. Morse Code Identification … 12-8 b. Voice Transmission … 12-8 c. Usable Distance: … 12-8 d. NDB Approach … 12-8 e. Bearing Tolerance Deviation … 12-8 f. Station Passage … 12-8 g. Standby Equipment … 12-8

Chapter 13. Area Navigation (RNAV) … 13-1

Table of Contents

Paragraph Page

x

1. Introduction … 13-1

2. Preflight Requirements … 13-2 a. Aircraft … 13-2 b. Navigation Database … 13-2 c. Pilot –Defined Procedure … 13-2 d. Evaluation of Procedure Data … 13-2 e. Navigation System Status … 13-4

3. Flight Inspection Procedures … 13-4 a. Checklist … 13-5 b. Detailed Procedures … 13-5 c. Aircraft Positioning … 13-5

4. Flight Inspection Analysis … 13-6 a. Waypoint spacing … 13-7 b. Procedural Design … 13-7 c. GPS Parameters … 13-7 d. Interference … 13-7

5. Tolerances … 13-8

6. Adjustments … 13-8

7. Documentation … 13-8

Section 2. Required Navigation Performance (RNP) RNAV … 13-9

8. Introduction … 13-9

9. Flight Inspection/Validation Procedures … 13-9

Section 3. Distance Measuring Equipment (DME) DME/DME-Supported RNAV . 13-10

10. Introduction … 13-10

11. Preflight Requirements … 13-10 a. DME Screening … 13-10 b. Data Collection … 13-10

12. Aircraft Positioning … 13-10 a. RNAV Departure Procedure/Standard Instrument Departure (SID) … 13-11 b. Routes … 13-12 c. RNAV Standard Terminal Arrivals … 13-12

13. Analysis … 13-12

14. Tolerances … 13-13

Section 4. Wide Area Augmentation System (WAAS) RNAV … 13-14

15. Introduction … 13-14

16. Preflight Requirements … 13-14 a. LP/LPV FAS Data Block Verification … 13-14

Table of Contents

Paragraph Page

xi

b. WAAS Status … 13-15

17. Flight Inspection Procedures … 13-15 a. Checklist … 13-15 b. Detailed Procedures … 13-15 c. Aircraft Positioning … 13-15

18. Flight Inspection Analysis … 13-16 a. CRC Remainder … 13-16 b. WAAS Signal … 13-16 c. Parameters … 13-16

19. Tolerances … 13-18

Chapter 14. Surveillance … 14-1

1. Introduction … 14-1 a. Primary Radar … 14-1 b. Secondary Radar … 14-1 c. Minimum Safe Altitude Warning System (MSAW) … 14-1 d. Precision Runway Monitor/Final Monitor Aid (PRM/FMA) … 14-2 e. Wide Area Multilateration (WAM) … 14-2

2. Flight Inspection Planning … 14-2 a. Facility Maintenance Personnel … 14-3 b. Flight Personnel … 14-4

3. Surveillance Radar Flight Inspections … 14-5 a. General … 14-5 b. Commissioning Inspections … 14-6 c. Periodic Inspections … 14-6 d. Special Inspections … 14-6

4. Surveillance Radar Checklist … 14-7

5. Surveillance Radar Detailed Procedures … 14-9 a. General … 14-9 b. Evaluation … 14-9 c. Inspection Sequence … 14-9 d. Orientation … 14-9 e. Tilt Verification … 14-10 f. Primary Radar Optimization … 14-10 g. Vertical Coverage … 14-10 h. Horizontal Screening … 14-17 i. Airway/Route Coverage … 14-17 j. Fix/Map Accuracy … 14-17 k. ASR Approach Procedures … 14-18 l. Fixed Target Identification … 14-19 m. Side-Lobe Suppression … 14-19 n. Modes and Codes … 14-20

Table of Contents

Paragraph Page

xii

o. ATCRBS Power Optimization … 14-20 p. GTC/STC Evaluation … 14-21 q. Communications … 14-21 r. Standby Equipment … 14-21 s. Standby Power … 14-22 t. MSAW … 14-22

6. WAM Flight Inspection Procedures … 14-22 a. General … 14-22 b. Commissioning Inspections … 14-23 c. Periodic Inspections … 14-23 d. Special Inspections … 14-23

7. WAM Checklist … 14-23

8. WAM Detailed Procedures … 14-25 a. General … 14-25 b. Vertical Transition Handoff … 14-25 c. General Coverage … 14-25 d. Perimeter Coverage … 14-25 e. Airway/Route Coverage … 14-26 f. Fix/Map Accuracy … 14-27 g. WAM Approaches … 14-27 h. Modes and Codes … 14-27 i. Communications … 14-27 j. Standby Equipment … 14-28 k. Standby Power … 14-28 l. MSAW … 14-28 m. Degraded System Configuration … 14-28

9. Analysis … 14-29 a. Testing Precautions … 14-29 b. Evaluation … 14-29 c. Probing … 14-29

10. Surveillance Radar and WAM Tolerances … 14-30

11. Documentation … 14-31

12. Facility Classification … 14-31

Section 2. Precision Approach Radar (PAR) … 14-32

13. Introduction … 14-32

14. Preflight Requirements … 14-32 a. Facility Maintenance Personnel … 14-32 b. Flight Personnel … 14-32 c. Special Equipment Requirements … 14-32 d. Theodolite Procedures … 14-32

Table of Contents

Paragraph Page

xiii

15. PAR Flight Inspections … 14-33 a. General … 14-33 b. Commissioning Inspections … 14-33 c. Periodic Inspections … 14-33 d. Special Inspections … 14-33

16. PAR Checklists … 14-34 a. Generic PAR (FPN-40, FPN-62/63, MPN-14, TPN-18, TPN-44) … 14-35 b. GPN-22, TPN-25 … 14-36 c. TPN-22 … 14-38 d. MPN-25/GCA(PAR)-2000/FPN-68, TPN-31 (31/A), FPN-67 … 14-40

17. PAR Detailed Procedures … 14-42 a. Azimuth Course Alignment … 14-42 b. Azimuth-Only PAR … 14-43 c. Course Deviation Accuracy … 14-43 d. Range Accuracy … 14-43 e. Distance Coverage … 14-44 f. Lateral Coverage … 14-44 g. MTI/MTD … 14-44 h. Glidepath Angle & Alignment … 14-45 i. Application of Glidepath Angle Tolerance … 14-46 j. PAR Coincidence … 14-46 k. Lower Safe Limit Angle & Alignment … 14-47 l. Lighting Systems … 14-47 m. Communications … 14-47 n. Standby Equipment … 14-47 o. Standby Power … 14-47

18. Analysis … 14-48

19. PAR Tolerances … 14-48

20. Adjustments … 14-48

Chapter 15. Instrument Landing System (ILS) … 15-1

Section 1. General … 15-1

1. Introduction … 15-1 a. ILS Zones and Points … 15-1 b. ILS Facilities Used for High Category Service … 15-1 c. Category I ILS Facilities (Localizer and Glide Slope Installed) Used to

Support lower than Category I Operations … 15-1 d. 75 MHz Markers … 15-2

2. Preflight Requirements … 15-3 a. ILS Flight Inspection Personnel … 15-3 b. ILS Special Equipment Requirements … 15-3 c. ILS Glidepath Origination Point … 15-3

Table of Contents

Paragraph Page

xiv

d. ILS Angular Reference … 15-3 e. ILS Theodolite Procedures … 15-7 f. 75 MHz Marker Facilities Maintenance Personnel … 15-9

3. Flight Inspection Procedures … 15-9 a. Types of Inspections and General Procedures … 15-9 b. Standby Equipment – Localizer/Glide Slope … 15-11 c. Standby Power – Localizer/Glide Slope … 15-11 d. Expanded Service Volume (ESV) … 15-11 e. Supporting NAVAID(s) … 15-12 f. Instrument Flight Procedures … 15-12 g. General Checklist … 15-12 h. Facility Checklists by Type … 15-12

Section 2. Localizer Flight Inspection Procedures … 15-32

4. Detailed Procedures - Localizers … 15-32 a. Spectrum Analysis … 15-32 b. Modulation Level … 15-32 c. Modulation Equality … 15-33 d. Power Ratio Check … 15-33 e. Phasing … 15-34 f. Course Sector Width and Symmetry … 15-34 g. Course Alignment Structure … 15-36 h. Glide Slope Signal on Localizer Back Course … 15-42 i. Monitor References … 15-42 j. RF Power Monitor Reference … 15-43 k. Clearance … 15-44 l. Coverage … 15-49 m. Reporting Fixes, SID(s)/DP(s) STAR(s), and Profile Descents … 15-49 n. Polarization Effect … 15-50 o. Identification and Voice … 15-50

Section 3. Glide Slope Flight Inspection Procedures … 15-52

5. Detailed Procedures – Glide Slope … 15-52 a. Spectrum Analysis … 15-52 b. Modulation Level … 15-52 c. Modulation Equality … 15-52 d. Phasing … 15-53 e. Engineering and Support Tests … 15-58 f. Angle Width, Symmetry, and Structure Below Path … 15-60 g. Clearance … 15-62 h. Mean Width … 15-63 i. Tilt … 15-63 j. Structure and Zone 3 Angle Alignment … 15-63 k. Transverse Structure – Endfire Glide Slope … 15-64 l. Coverage … 15-65

Table of Contents

Paragraph Page

xv

m. Monitors … 15-65 n. RF Power Monitor Reference … 15-65

Section 4. 75MHZ Marker Beacon Flight Inspection Procedures … 15-67

6. Introduction … 15-67 a. Spectrum Analysis … 15-67 b. Identification and Modulation Tone … 15-67 c. Coverage … 15-67 d. Proximity Check … 15-68 e. Measurement Methods … 15-69 f. Holding Fixes … 15-70 g. Standby Equipment … 15-70 h. Standby Power … 15-70

Section 5. Analysis (ILS and Marker Beacons) … 15-71

7. ILS Analysis … 15-71 a. Structure Tolerances (95% Rule) … 15-71 b. Rate of Change/Reversal in the Slope of the Glidepath … 15-71 c. Application of Localizer Coverage Requirements … 15-72 d. Application of Glide Slope Coverage Requirements … 15-73 e. CAT III Adjust and Maintain … 15-74 f. ILS Maintenance Reference Tolerances and Alerts … 15-74 g. Glide Slope Snow NOTAM … 15-77 h. Threshold Crossing Height (TCH)/Reference Datum Height (RDH) … 15-78 i. Adjustments … 15-78

8. 75 MHz Marker Analysis … 15-78

Section 6. Tolerances … 15-83

9. Tolerances … 15-83 a. Localizers … 15-83 b. Glide Slopes … 15-89 c. 75 MHZ Marker Tolerances … 15-92

10. Adjustments … 15-94

Chapter 16. Reserved … 16-1

Chapter 17. Ground Based Augmentation System (GBAS) … 17-1

1. Introduction … 17-1

2. Preflight Requirements … 17-1 a. Inspection System Calibration … 17-2 b. Dmax Determination … 17-2 c. GBAS Position, Velocity, and Time (PVT) Mode … 17-2 d. GBAS FAS Data Block Validation … 17-3 e. GBAS Supporting Parallel Runways … 17-3

Table of Contents

Paragraph Page

xvi

3. Flight Inspection Procedures: … 17-6 a. Checklist … 17-6 b. GBAS VDB Coverage … 17-7 c. GBAS Approach Service Volume … 17-8 d. Autoland or Guided Takeoff … 17-9 e. VDB Coverage Evaluation … 17-10 f. Approach Procedure Coverage Assessment … 17-10 g. Aircraft Positioning … 17-16 h. Periodic Evaluation … 17-17 i. Special Inspection … 17-17 j. Flight Inspection Analysis … 17-19 k. Tolerances … 17-22

Chapter 18. Reserved … 18-1

Chapter 19. Reserved … 19-1

Chapter 20. Flight Inspection of VFR Aeronautical Charts … 20-1

1. Introduction … 20-1 a. Sectional Aeronautical Chart … 20-1 b. Terminal Area Chart (TAC) … 20-1 c. Charted VFR Flyway Planning Chart … 20-1 d. Grand Canyon VFR Aeronautical Chart … 20-1 e. Helicopter Route Chart … 20-1

2. Preflight Requirements … 20-1

3. Detailed Procedures … 20-1 a. Flight Line Track … 20-2 b. Altitudes … 20-2 c. Weather … 20-2

4. Analysis and Evaluation … 20-2

Chapter 21. Helicopter … 21-1

Chapter 22. Flight Inspection of Expanded Service Volume (ESV) for Ground-Based Navigational Aids … 22-1

1. Introduction … 22-1 a. Standard Service Volume (SSV) … 22-1 b. Flight Inspection Standard Service Volume (FISSV) … 22-1 c. Expanded Service Volume (ESV) … 22-1 d. Operational Service Volume (OSV) … 22-1

2. Detailed Procedures … 22-1 a. Rho-Theta … 22-1 b. Instrument Landing System (ILS) … 22-4

Table of Contents

Paragraph Page

xvii

c. Nondirectional Beacon (NBD) … 22-6 d. Distance Measuring Equipment (DME) … 22-7 e. Area Navigation (RNAV)—Procedural Routes Predicated on DME/DME

Position Estimation … 22-7

3. Expanded Service Volume Process … 22-8 a. FMO-Approved Limits … 22-8 b. Clarity of Flight Inspection Results … 22-8 c. Expanded Service Volume (ESV) Facilities … 22-8

4. Flight Inspection Tolerances … 22-9

Chapter 23. Radio Frequency Interference (RFI) Detection … 23-1

1. Introduction … 23-1 a. Airborne investigation … 23-1 b. Types of Interferers … 23-1

2. Preflight Requirements … 23-1 a. Facility Maintenance Personnel … 23-1 b. Flight Personnel … 23-2

3. Flight Inspection Procedures … 23-2

4. Checklist … 23-2

5. Detailed Procedures … 23-2 a. Airborne Equipment … 23-2 b. Search patterns … 23-3

6. Analysis … 23-4 a. Intermittent Interference … 23-4 b. Analyze the interfering signal … 23-4

7. Tolerances … 23-4

8. Adjustments … 23-4

9. Records and Reports … 23-4

Chapter 24. Military Contingency and Natural Disaster Flight Inspection Procedures .. 24-1

Section 1. General … 24-1

1. Introduction … 24-1 a. Purpose … 24-1 b. Authority … 24-1

2. Preflight Requirements … 24-1 a. Personnel Requirements … 24-1 b. Aircraft and Equipment … 24-1

3. Flight Inspection Documentation and Reports … 24-2 a. Documentation … 24-2

Table of Contents

Paragraph Page

xviii

b. Reports … 24-2

Section 2. Military Contingency Procedures … 24-3

4. Inspection Types … 24-3

5. Frequency of Inspection … 24-3 a. Non-precision … 24-3 b. Precision … 24-3 c. RNAV SIAP(s) … 24-3

6. Pre-Inspection Requirements … 24-3 a. FAA Pre-Arrival Coordination … 24-3 b. Airfield Operations Pre-Arrival … 24-4 c. Facility Maintenance Pre-Arrival … 24-4

7. Instrument Procedures … 24-4 a. Approach Procedure … 24-4 b. En Route and Transition Coverage … 24-5 c. Departure Procedure … 24-5 d. Communications … 24-5

8. Facility Status and NOTAM(s) … 24-5

Section 3. Natural Disaster Procedures … 24-7

9. Inspection Types … 24-7

10. Frequency of Inspections … 24-7 a. Non-precision … 24-7 b. Precision … 24-7

11. Facility Status and NOTAM(s) … 24-7

Section 4. Flight Inspection Procedures/Tolerances … 24-8

12. ILS Glide Slope … 24-8

13. ILS Localizer … 24-9

14. Markers/Beacons … 24-10

15. VOR … 24-11

16. TACAN … 24-12

17. Shipboard TACAN … 24-13

18. PAR … 24-14

19. ASR/ATCRBS Radar … 24-14

20. Homing Beacons … 24-15

21. DF Facilities … 24-15

22. VGSI … 24-15

Table of Contents

Paragraph Page

xix

23. RNAV Procedures … 24-16

Chapter 25. Administrative Information … 25-1

1. Distribution … 25-1

2. Background … 25-1 a. U.S. Policy … 25-1 b. Program Objectives … 25-1 c. Interface with Agency Rules … 25-1 d. Flight inspection programs … 25-2 e. Design Standards for Air Navigation Services … 25-2 f. North Atlantic Treaty Organization (NATO) Standardization Agreement

(STANAG) … 25-2 g. Quality Assurance … 25-2

3. Authority to Change This Order … 25-2

4. Definitions … 25-2

5. Unit of Measurement … 25-2

6. Identifying Changes in the Text of This Manual … 25-3

Appendix A. Supplemental Information … A-1

1. Definitions and Symbols … A-1

2. Abbreviations, Acronyms, and Letter Symbols … A-39

Appendix B. Formulas … B-1

1. Introduction … B-1

2. General … B-1

3. TACAN … B-3

4. Markers (75MHz) … B-4

5. Radar … B-4

6. Localizer … B-4

7. Glide Slope … B-5

8. Precision Approach … B-5

9. Procedures … B-6

10. PFE/PFN.CMN Angular Tolerances … B-6

11. FMS Waypoint DME Evaluation Obit/ARC Radius … B-6

Appendix C. Working Graphs and Charts … C-1

1. NAVAID Service Volumes … C-6

Table of Contents

Paragraph Page

xx

2. VOR MON Service Volumes … C-9

3. NextGen DME Service Volumes … C-10

Appendix D. Frequency Spectrum … D-1

1. Frequency Allocation … D-1

2. Nomenclature of Frequency Bands … D-3

Appendix E. Map Interpretation … E-1

1. Introduction … E-1

2. Aeronautical Chart Preparation … E-1

3. Preparation of Charts for Flight Inspection Use … E-2

4. Use of the Chart … E-3

Appendix F. UHF Homing Beacons … F-1

1. Introduction … F-1

2. Preflight Requirements … F-1

3. Flight Inspection Procedures … F-1

4. Analysis … F-3

5. Tolerances … F-4

Appendix G. Directive Feedback Information … G-1

a. Chapter 4: › (6) Paragraph 12.c. Reconfiguration of Precision Approach Services.…

Chapter 1. General Information

1. Purpose of This Order. This order contains the policy, procedures, and criteria for flight inspection and certification of air navigation services, instrument flight procedures, and FAA VFR Aeronautical Charts. The order applies to the flight inspection of all National Airspace System (NAS) and Department of Defense (DOD) air navigation services and instrument flight procedures.

2. Audience. All FAA and DOD Flight Inspectors.

3. Where to Find This Order. You can find this order on the FAA website at http://www.faa.gov/regulations_policies/orders_notices and anywhere else that you may put your orders for your audience.

4. What This Order Cancels. 8200.1D, United States Flight Inspection Manual, Change 1 and all accompanying manuals.

5. Explanation of Policy Changes. This order has been reformatted and updated to remove canceled FAA order and form references and to reflect the current organizational structure. Paragraph and item reference hyperlinks have been updated as necessary. Chapter 16, Microwave Landing System and all subsequent references to MLS and MMLS have been removed from this order. Chapter 14 has been retitled to Surveillance. Chapter 17 Local Area Augmentation System (LAAS) has been replaced with Ground Based Augmentation System (GBAS). The content of Chapters 4, 11, and Appendices A and C has been changed as follows:

a. Chapter 4:

(1) Paragraph 5, Special Flight Inspections. Added “Special inspections are also performed at the request of the Spectrum Engineering Services Group, when RFI degrades intended facility services.”

(2) Paragraph 5.f., Radio Frequency Interference (RFI) has been removed. Subsequent paragraphs were renumbered.

(3) Paragraph 5.f(3)(b) (formerly 5.g(3)(b)), Complete Periodic Checklist Requirements. Added “ILS does not require monitor configurations.”

(4) Paragraph 12. Periodic Flight Inspection Intervals. This section has been reformatted to better align with the FAA Long Order Template removing “Establishing the Interval.”

(5) “Newly commissioned GBAS facilities” paragraph has been moved under Paragraph 12.a. Commissioning.

(6) Paragraph 12.c. Reconfiguration of Precision Approach Services. Sentence rewritten for clarification: “For ILS (ILS DME is not part of the precision system), a full periodic with monitor reference check on both the reconfigured system (localizer and or glide slope or both) facilities must be scheduled as part of this special, and the periodic with monitors must be updated on the Daily Flight Log (DFL).”

d. Chapter 14: › (2) Paragraph 5.i., Airway/Route Coverage. Revised to clarify the final…

(7) Paragraph 13. ILS Monitor (or Reference) Intervals. Table 4.1. Basic Schedule for Periodic Flight Inspection. Removed MMLS and MMS and added WAM. Note added: “ASR without SIAPs have no periodic interval requirements.”

(8) Paragraph 16. Preflight Inspection Preparation. Removed second paragraph referencing meeting with coordinators and cartographers prior to VFR Aeronautical Chart flight inspections.

(9) Paragraph 18. Analysis and Evaluation. Removed Paragraph 18.c. “VFR Aeronautical Chart inspections must record their notes” paragraph. Subsequent paragraphs were renumbered.

(10) Paragraph 19.b. VFR Aeronautical Charts. This paragraph was rewritten to clarify duties.

b. Chapter 5:

(1) Paragraph 2.j(14). NOTAM Examples. Removed Condition 14, subsequent paragraphs were renumbered, if necessary.

c. Chapter 11:

(1) Paragraph 4.f., Orbit Evaluations. Added “Maintenance has 96 hours from completion of inspection to perform post flight inspection ground reference checks for the inspection to be valid.”

(2) Paragraph 4.j., Standby Power. Removed incorrect paragraph reference.

(3) Paragraph 5.e., Polarization. Added “The evaluations should be conducted on another nearby radial in the same azimuth quadrant, or on the same radial at a higher altitude to rule out environmental reflections.”

(4) Paragraph 5.e(1). Changed to clarify that confirmation checks can be done using the alternate method.

(5) Paragraph 5.e(2). Changed “confirmation procedure” to “alternate method.”

d. Chapter 14:

(1) Surveillance Radar Checklist. Revised Note (2): Check the GTM “only on ASR systems that support approaches.” Added Note (5): “If commissioning an ASR approach to a facility that has previously not had an approach, notify the Mission Technical Support Group.

(2) Paragraph 5.i., Airway/Route Coverage. Revised to clarify the final commissioning check “must be” accomplished using a flight inspection aircraft “on those routes or airways that require radar surveillance.”

g. Appendix C: › (2) Added NextGen DME Service Volume image and description.

(3) Paragraph 5.k(1). Added “All original and amended ASR approaches must be certified by flight inspection prior to implementation.”

(4) Paragraph 5.s., Standby Power. Added “Flight inspection is not required when the facility is powered by batteries that are constantly charged by another power source.”

(5) Paragraph 16.d., MPN-25/GCA(PAR)-2000/FPN-68, TPN-31 (31/A), FPN-67. Added “The MPN-25 has an integrated ASR with a nominal range of 30 nm in Clear Mode (19 nm in Rain Mode).”

(6) Paragraph 17.d., Range Accuracy. Added “The flight inspector will verify the PAR controller is able to determine when the aircraft is over the runway threshold, but a range error measurement at this point is not required.

e. Chapter 15:

(1) Paragraph 2. Removed “ILS Facilities Maintenance Personnel. Prepare for flight inspection in accordance with Chapter 4, Section 3.”

(2) Removed Paragraph 7 to eliminate redundancy. Renumbered subsequent paragraphs.

f. Appendix A:

(1) Added the following definitions: azimuth accuracy, carrier modulation, elevation accuracy, fan marker beacon, global positioning system (GPS), ILS integrity, performance-based navigation (PBN), and pressure-altitude.

(2) Removed all definitions related to MLS and control electronic unit (CEU).

(3) Revised the quadrant definition.

(4) Added FIAPA to Abbreviations, Acronyms, and Letters section.

(5) Removed AVN, CMLSA, FICO, FIP, MDP, MLS, and NACO from Abbreviations, Acronyms, and Letters section.

g. Appendix C:

(1) Added VOR MON Standard Service image and description.

(2) Added NextGen DME Service Volume image and description.

Chapter 2. Flight Inspection Crew Authority and Responsibilities › 2. Responsibility.

Chapter 2. Flight Inspection Crew Authority and Responsibilities

1. Authority. The flight inspection crew is authorized to:

• Perform flight inspections of air navigation systems to determine that such systems meet applicable tolerances contained in this manual, and that the facility will support the associated instrument flight procedures;

• Perform surveillance of aeronautical services;

• Issue Notice to Air Missions (NOTAMs) subject to the limitations contained in Chapter 5, Section 1;

• Certify the signal-in space of a facility based on the result of the flight inspection;

• Report hazards encountered during a flight inspection of any type;

• Take appropriate procedural actions; and

• Review, verify, and edit topographic, cultural, and obstruction data depicted on FAA VFR Aeronautical Charts for accuracy and navigational usefulness.

2. Responsibility. The flight inspection crew is responsible for:

• Conducting flight inspections in accordance with the procedures established by this manual;

• Determining the adequacy of the system to meet its required functions;

• Analyzing and evaluating the flight inspection data to enable a status classification to be assigned;

• Certifying the signal-in-space of a NAVAID in accordance with the tolerances prescribed in this manual;

• Coordinating with engineering, maintenance, and/or Air Traffic personnel;

• Reporting the flight inspection results and status of the systems to the appropriate authority;

• Providing the technical details for NOTAMs based on the flight inspection data;

• Making recommendations to military installation commanders regarding NOTAMs for military services;

• Verifying the accuracy of NOTAMs and published information;

• Flight inspecting instrument flight procedures prior to their publication;

• Optimizing facility performance during flight inspections requiring adjustments;

• Determining that RNAV procedural leg types meet the intent of the instrument procedure; and

• Conducting flight inspection of non-public procedures in accordance with (IAW) this manual and proponent’s approved criteria. Documenting findings for Flight Standards Service use in approving or denying the procedure.

Chapter 3. Special Requirements

1. Introduction. This chapter describes the special requirements of the aircraft flight crewmembers, and airborne and ground support equipment used for flight inspection.

Chapter 3. Special Requirements › 4. Airborne and Ground Support Equipment.

2. Aircraft. Organizations conducting flight inspection must identify specific requirements based on their operational needs. Appropriately equipped aircraft and helicopters, from service proponent or other sources, may be used when required to complete flight inspection requirements. The general characteristics of a flight inspection aircraft should be as follows:

• Equipped for night and instrument flight.

• Sufficient capacity for a flight inspection crew, observers, ground maintenance and/or installation personnel, and required electronic equipment with spares.

• Sufficient range and endurance for a normal mission without reservicing.

• Aerodynamically stable throughout the speed range.

• Low noise and vibration level.

• Adequate and stable electrical system capable of operating required electronic and recording equipment and other aircraft equipment.

• Wide speed and altitude range to allow the conduct of flight inspections under normal conditions as encountered by the users.

• Appropriate for modifications for flight inspection of new and improved navigation services.

3. Flight Inspection Crewmembers. Flight inspection organizations certifying air navigation services must develop a program to formally certify flight inspection personnel. The objectives of this program are to:

• Grant authority to the flight inspection crewmembers who carry out the administration’s responsibility of ensuring the satisfactory operation of air navigation services, instrument flight procedures, and VFR Aeronautical Chart verification.

• Provide a uniform method for examining employee competence.

• Issue credentials which authenticate certification authority for the crewmember.

4. Airborne and Ground Support Equipment. Aircraft and ground support flight inspection equipment must be calibrated to a standard traceable to the National Institute of Standard and Technology.

• An Automated Flight Inspection System (AFIS), when applicable, is the primary method for conducting flight inspections.

• Other approved systems (Portable/Utility Class) and methods (Theodolite, RTT, or Manual) may be used unless prohibited by other policy for flight inspection. These systems/methods must not be used solely to bypass the need for facility data of sufficient accuracy to support AFIS. Portable/Utility class equipment, installed in aircraft for the purpose

of conducting flight inspections, must be installed in accordance with Flight Program Operations approved procedures.

5. Special Flight Inspections. › b. USAF Deployable (Mobile) ATCALS (DATCALS).

Chapter 4. Flight Inspection Types, Priorities, Intervals, Procedures

Section 1. Types and Priorities of Flight Inspections

1. Introduction. Official flight inspections are of five basic types: site evaluation, commissioning, periodic, special, and surveillance.

2. Site Evaluation. A flight inspection to determine the suitability of a proposed site for the permanent installation of a facility. It may include checks normally made during a commissioning inspection and any additional tests which may be required.

3. Commissioning. A comprehensive flight inspection designed to obtain complete information as to system performance and to establish that the system will support its operational requirements.

Occasionally, a commissioning inspection is performed prior to the completion of runway construction activities, including but not limited to, painting and lighting. When this occurs, a Special Flight Inspection should be performed after completion of the runway work and before the facility is placed into service. The flight inspector performing the commissioning check must request the Special inspection, specifying the items needing inspection. If, in the flight inspector's judgment, the remaining runway work is negligible and no Special inspection is required before facility use, the condition must be documented on the Daily Flight Log.

4. Periodic. A regularly scheduled flight inspection to determine that the system meets standards and supports the operational requirements.

5. Special Flight Inspections. These are inspections performed outside the normal periodic interval. They may be used to define/evaluate performance characteristics of systems, subsystems, or individual facilities. Facilities maintenance personnel must be responsible for coordinating with flight inspection which checks are to be accomplished, based on their requirements and type of maintenance performed on the equipment. Special inspections are also performed, at the request of the Spectrum Engineering Services Group, when radio frequency interference (RFI) degrades intended facility services.

a. USAF Air Traffic Control and Landing System (ATCALS) evaluation requirements. ATCALS evaluation inspections require a minimum of a periodic-with-monitors type profile for ILS and periodic-type profile for all other.

b. USAF Deployable (Mobile) ATCALS (DATCALS). Flight inspections of DATCALS deployed to support an exercise or operational readiness inspection (ORI), and not intended for actual use, are considered special inspections. Inspected these facilities to the extent necessary to assess the mobile unit’s deployment capability. The procedures and checklists contained in Chapter 24 will normally be accomplished. The ORI/exercise team chief will be responsible, after consulting with the flight inspector, for assessing the facility and determining if the unit could operate during an actual deployment. The facility classification will be “unusable” due to the limited nature of the check.

(3) Inspection Procedure(s). › (b) Complete periodic checklist requirements.

c. Unapproved Facilities. Inspections of facilities not approved for use (equipment under test, facilities without monitors, etc.) will be special inspections. Since these facilities cannot be commissioned for IFR use, the status will be unusable. Items inspected will be largely dependent on the customer’s request.

d. Facility Removal and Replacement. When the equipment replaced is the same type and configuration as the former and located on the same physical site, including antenna location, a special check is required. Required items for an antenna change in each chapter must be accomplished as a minimum. Additional requirements of such a check will be jointly determined by the flight inspector and facilities maintenance.

e. New or Modified Equipment Testing. Coordinate all testing of new or modified types of equipment that require flight inspection support with the Mission Technical Support Group. The Mission Technical Support Group will determine if personnel from that office will participate in the testing to both ensure the adequacy of the testing and scope of any flight inspection procedural changes required to support the equipment. This encompasses Operational Testing and Evaluation (OT&E), First Article Testing, Developmental Test and Evaluation (DT&E), and similar formal testing; it does not include normal flight inspection of subsequent installations. If any doubt exists about the need for coordination, contact the Mission Technical Support Group.

f. After Accident. This inspection is performed at the request of the accident coordinator/investigator to verify that system performance is satisfactory and continues to support instrument flight procedure(s).

(1) Response. This inspection has a priority of 1a and should be accomplished as soon as possible.

(2) Preflight Requirements. The flight inspector must obtain the following information:

(a) Equipment configuration at the time of the accident, i.e., the receiver(s), transmitter(s), or radar channel(s) in operation.

(b) Instrument flight procedure(s) used.

(c) Any additional information that may aid in the inspection analysis.

(3) Inspection Procedure(s).

(a) Coordinate with maintenance to configure the system as indicated in Paragraph 5.g(2)(a).

(b) Complete periodic checklist requirements. Only the equipment and instrument flight procedures used by the accident aircraft need to be checked. ILS does not require monitor configurations. A VOR or TACAN alignment orbit is not required. Do not make any facility adjustments during the after-accident inspection. Any adjustments must require a separate special inspection.

b. Inspections. › (2) Runway, taxiway paint markings, and position signs missing or…

(c) If a system or procedure has no periodic inspection requirements, evaluate performance in the area in which the accident occurred.

(d) Complete any additional items requested by maintenance, air traffic control personnel, the accident coordinator, or the commander at a military facility.

(e) Where an accident involves contact with the terrain or a manmade obstruction, confirm the procedural controlling obstruction by map study or flight evaluation.

(4) Dissemination of After Accident Information. All flight inspection findings or other pertinent accident investigation information must be restricted to the cognizant accident coordinator/investigator, maintenance, and air traffic personnel. Results of the flight inspection must be given to the FAA Inspector-in-Charge (IIC) as soon as possible. A flight inspection report must be filed in accordance with current directives.

g. Reconfiguration. A special flight inspection requested by maintenance when modifications or the relocation of a facility affect the radiation pattern of the facility. Classify antenna changes to different type antennas as a reconfiguration inspection. Perform all commissioning checks following a facility reconfiguration, except those not required as determined jointly by flight inspection and facilities maintenance personnel. Apply commissioning tolerances.

h. Inspections of Shipboard TACAN(s) are considered complete at the termination of the inspection. Any subsequent inspection must be a new "special" inspection.

6. Surveillance. An ongoing observation of individual components of commissioned systems, procedures, or services. This inspection encompasses spot checks of individual components observed during normal flight operations. No reporting is required unless a discrepancy is found. An out-of-tolerance or unsatisfactory condition found on a surveillance inspection requires a Daily Flight Log entry, report, and, if necessary, NOTAM action.

a. Surveillance of Aeronautical Services. During routine flight operations, flight inspection personnel must be alert for items which are unusual, substandard, or possibly hazardous.

b. Inspections. Inspections may include, but are not limited to, the following:

(1) Condition of runways, taxiways, and ramp areas.

(2) Runway, taxiway paint markings, and position signs missing or deteriorated to the extent that visual guidance is obscured or missing.

Chapter 4. Flight Inspection Types, Priorities, Intervals, Procedures › 7. Priorities of Flight Inspection.

(3) Conditions which may lead to runway incursion by aircraft, vehicles, or pedestrians.

(4) Construction activity at airports which is a hazardous condition or might affect NAVAID performance.

(5) New obstructions in the instrument approach area which might become the controlling obstruction or constitute a hazardous condition.

(6) Brush or tree growth obstructing the view of approach lights.

(7) Obscured or broken runway or obstruction lights.

(8) Other hazardous situations (e.g., bird hazards).

(9) Air traffic services (e.g., clearances, flight plans, communications).

(10) Other services (e.g., weather bureau services or other airport support services).

c. Reports. See FAA Order 8240.36, Flight Inspection Report Processing System (latest edition).

7. Priorities of Flight Inspection. Use the priorities listed below to determine which mission will be supported first when two or more requirements are competing for limited flight inspection resources. Schedule all inspections to make the most effective use of aircraft and crew members. Schedulers should consider weather; maintenance team availability; other facilities enroute; impact on both the airport and NAS; and Technical Operations Facilities, Service, and Equipment Profile (FSEP) Response Codes when scheduling missions.

Priority Type of Service 1a Accident Investigation, RFI impacting NAS services, any facility which has exceeded its inspection interval, inspection of facilities in support of military contingencies, or other nationally directed military deployments.

1b Restoration of a commissioned facility after an unscheduled outage, restoration of CAT II/III ILS approach minimums, or inspection of NAVAID(s) in support of military operational readiness and JCS directed exercises.

1c Flight inspection of reported malfunctions.

1d Restoration of a commissioned facility following a scheduled shutdown or inspections supporting DOD NAVAID evaluations (USAF TRACALS).

2a Site evaluation.

2b Commissioning inspection of a new facility or new instrument flight procedures.

Priority Type of Service

3a Periodic inspections.

3b Restoration of standby equipment (except CAT II/III ILS, see priority 1b).

3c Navigational Aids Signal Evaluator (NASE) evaluations.

3d Restoration of VFR training facilities following a scheduled or unscheduled outage.

b. Scheduling. › (3) Periodic inspections are considered complete when all scheduled…

Section 2. Frequency of Periodic Flight Inspection

8. Introduction. This section prescribes the minimum frequency of periodic flight inspections. Make more frequent inspections when deemed necessary or as requested by the owner or organization responsible for the operation of the facility.

a. Intervals. Table 4-1 specifies the intervals between scheduled periodic flight inspections. Use this schedule to determine dates for periodic inspections. Military, foreign, and MOA systems, facilities, and procedures may have unique requirements and non-standard inspection intervals. All records and reports will reflect the actual date(s) of the inspection and will specifically denote the date of completion. The next periodic inspection will be predicated on the actual date of completion.

(1) Due date window for facilities with a 90-day periodicity is from 15 days before to 15 days after the due date.

(2) Due date window for all other facilities, systems, and procedures is from 60 days before to 60 days after the due date.

(3) Due date window for VFR Aeronautical Charts is from 120 days before to 120 days after the due date.

Note: the VFR Flight Inspection Program will implement VFR Chart periodicity over a period of years.

For the contiguous United States, the chart periodicity is being implemented over the next several years. The periodic due date for each individual Sectional Aeronautical Chart and its associated Terminal Area and Flyway Chart is being established as the chart is inspected.

Inspection and periodicity for the Aeronautical Charts outside the contiguous United States will be implemented in the future. Helicopter and Special VFR Charts have no periodicity and are updated as determined by the Aeronautical Charting Group.

b. Scheduling.

(1) NAVAID(s) such as VORTAC, VOR/DME, ILS, etc., must be flight inspected as a service with the same due date and inspection interval for all component facilities.

(2) The inspection priority must be raised to 1a when the system, facility, or procedure has exceeded the end of the due date window.

(3) Periodic inspections are considered complete when all scheduled checks are accomplished except as noted below. When flight inspection of all Standard Instrument Approach Procedures (SIAP(s)) cannot be completed within the periodic window and extension, the periodic inspection will be documented as complete, as directed by the Flight Program Operations Flight Operations Team (FOT) Manager.

Chapter 4. Flight Inspection Types, Priorities, Intervals, Procedures › 10. NAVAIDS Temporarily Out-of-Service.

Special inspections must be established to ensure the remaining SIAP(s) are completed. In the event the SIAP(s) are not checked by the end of the periodic window/extension, the appropriate Flight Program Operations’ scheduler must initiate NOTAM action to remove them from service. The SIAP(s) must be restored by a special flight inspection.

(4) Progressive Inspections. The requirements for periodic inspections are specified in a checklist in each chapter of this order. Partial or progressive inspections may be conducted, provided all individual periodic checklist items are satisfied within the due date window.

9. Extension of Services Overdue Periodic Inspection. When the inspection of a commissioned NAVAID or SIAP is not completed within the due date window, the window may be extended. The flight inspection priority of a NAVIAD or SIAP in an extension is the same as an overdue NAVAID or procedure.

The periodic flight inspection window for a ground NAVAID may be extended an additional seven (7) calendar days if the FOT Manager and regional facility maintenance engineering agree that no conditions exist which could adversely affect the safety of flight.

The periodic flight inspection window for all SIAP(s) may be extended an additional thirty (30) calendar days providing:

• A review of the SIAP is accomplished by a flight inspector;

• The Flight Program Operations scheduler, by coordination with regional or local airport personnel, can determine that no known environmental (i.e., construction or natural growth) changes have occurred which could adversely affect the procedure and;

• The Aeronautical Services Flight Procedures Office agrees that an extension of the window will not adversely affect the safety of flight.

10. NAVAIDS Temporarily Out-of-Service.

• Use the priority listed in Section 1 of this chapter when a restoration inspection is required. The next periodic inspection must be predicated on the completion date of an inspection which satisfies all periodic checklist requirements.

• When a portion of a NAVAID is restored to service, establish the periodic due dates in accordance with Table 4-1.

• Standby Equipment or Associated NAVAID. When flight inspection of standby equipment or an associated NAVAID is required but cannot be accomplished, the periodic inspection will be considered complete if the standby equipment or associated NAVAID is out- of-service (awaiting parts, etc.), or removed from service (due to an uncorrectable discrepancy, etc.).

• Restore the standby equipment or associated NAVAID to service by the successful completion of a flight inspection which satisfies all periodic requirements (including monitors, where applicable.)

12. Periodic Flight Inspection Intervals. › c. Reconfiguration of Precision Approach Services.

11. Rho-Theta Receiver Checkpoints. When periodic or special flight inspections of ground or airborne receiver checkpoints cannot be completed, consider the inspection complete. The following actions will be taken:

• The flight crew will document the required inspection as complete on both the Daily Flight Log (DFL) and the flight inspection report. Enter in Remarks those checkpoints that were not checked.

• The appropriate Flight Program Operations scheduler will:

o Schedule a special inspection to complete the checkpoints within the established

facility periodicity.

o Take appropriate NOTAM action to remove the receiver checkpoints from service if

the special inspection is not completed within the established facility periodicity. Notify the airport manager that the ground receiver checkpoints must be removed or covered.

12. Periodic Flight Inspection Intervals. The schedule for periodic flight inspections will be in accordance with Table 4-1

a. Commissioning. Inspect newly commissioned precision facilities initially at a 90, 180, and 270-day interval and then maintain the schedule established in Table 4-1. Basic Schedule for Periodic Flight Inspection. For PAR, each runway served and alternate angle or touchdown point used must be inspected on the 90 and 180-day checks. For ILS, a periodic with Monitor check is required for the initial 90, 180, and 270-day checks. This requirement also applies to the glide slope, but not the localizer when a glide slope is added to a localizer-only or LDA/SDF facility.

Newly commissioned GBAS facilities must be inspected initially on a 360-day interval. After two concurrent 360-day periodic cycles with no GBAS out-of-tolerance condition, the periodic interval may be increased to 540 days. During a 540-day periodic interval, any facility out-of- tolerance condition is cause to reset the GBAS back to the initial periodic interval requirement of 360 days until there are two out-of-tolerance condition free cycles.

b. Specials Other Than Reconfigurations. Facilities may be restored to the existing periodicity without further checks once the special is complete and deemed satisfactory by Technical Operations engineering or maintenance personnel. The periodic due date may be updated if all system periodic requirements for the next scheduled periodic inspection are completed during any special inspection.

c. Reconfiguration of Precision Approach Services. Check reconfigured precision approach services at 90 days. For ILS (ILS DME is not part of the precision system), a full periodic with monitor reference check on the reconfigured system (localizer or glide slope or both) must be scheduled as part of this special, and the periodic with monitors must be updated on the Daily Flight Log (DFL). The next periodic due date will be at the 270-day interval. For PAR, each runway served and alternate angle or touchdown point used must be inspected on this check.

Chapter 4. Flight Inspection Types, Priorities, Intervals, Procedures › 13. ILS Monitor (or Reference) Intervals.

13. ILS Monitor (or Reference) Intervals. ILS monitor inspection must be conducted every periodic for ILS and LDA/SDF with GS. Monitor inspections must be conducted every other periodic for LDA/SDF/LOC only facilities.

Table 4-1. Basic Schedule for Periodic Flight Inspection (all intervals are in days)

Approach Obstacle Assessment 540 SIAP 540 (5) Facility Interval ILS/LDA/SDF w/GS 540 Localizer Clearances at LSA 1,080 GBAS 540 (6) PAR 27 ASR 540 (8) WAM 540 DF 540 LDA/SDF/LOC only 540 (2) NDB (UHF, LF/MF) 540 VOR, VORTAC, TAC 540 (1) VOR, VORTAC, TAC 1,080 VOT 540 DME, NDB facilities associated with an

Instrument Approach Procedure, Marker Beacons, Communications, VGSI, and Approach Lighting Systems

Inspect these facilities at the same interval as

the system or procedure they support.

Notes:

(1) 540 days for facilities (VOR or TACAN of a VORTAC) which support a SIAP or

receiver checkpoint. An alignment orbit is required every 1,080 days for all facilities. (2) Monitors required every other inspection. See Paragraph 13 in Chapter 4. (3) SIAP check required every 360 days. (4) 1,080 days for facilities that do not support a SIAP or receiver checkpoint. (5) For all periodic SIAP inspections, the periodic obstacle assessment may be conducted

independent of the SIAP inspection. Periodic inspections of RNAV or GBAS SIAP(s) do not require flying the actual procedure; however, an obstacle assessment must be conducted through the final and missed approach segments. (6) See Paragraph 12 in Chapter 4. (7) Next Generation DME (NextGen DME) facilities without a primary facility (i.e., VOR,

TACAN, localizer, or NDB). (8) ASR without SIAPs have no periodic interval requirements.

16. Preflight Inspection Preparation. › a. Facilities Maintenance Personnel.

Section 3. General Flight Inspection Procedures

14. Introduction. Sequence of events encountered by the flight inspector in the performance of the flight inspection mission is generally as follows:

• Request for flight inspection;

• Scheduling of flight inspection;

• Preflight preparation;

• Actual flight inspection;

• Analysis and evaluation; then

• Post flight review and reporting.

15. Request for Flight Inspection. Authorized personnel must request site, commissioning, and some special flight inspections. Requests are not required for periodic flight inspections.

a. Status of Equipment. Initiate the flight inspection request when the inspection requirement is known and finalize the schedule when the facility is ready for flight inspection.

b. Notification. Flight Program Operations schedulers will notify the appropriate facility maintenance personnel of the estimated time of arrival (ETA) of the flight inspection aircraft. Provide as much advance notification as possible for a site evaluation, commissioning inspection, periodic with monitors, or inspections requiring maintenance support.

c. Localizer Periodic Inspection Without Monitors. Does not require pre-coordination with maintenance personnel. Conduct this inspection on the transmitter in operation. If an outof-tolerance condition is found, notify maintenance of the discrepancy(ies) found and inspect the standby equipment. Issue NOTAM(s) if discrepancies are not corrected.

16. Preflight Inspection Preparation. A thorough and complete understanding between Facilities Maintenance and the flight inspection crew is essential for a successful flight inspection. The flight inspector and the person-in-charge of the facility are jointly responsible for the required coordination before, during, and after the flight inspection. The flight inspector will brief the Facilities Maintenance personnel of intended actions prior to commissioning flight inspections and for special circumstances.

a. Facilities Maintenance Personnel. Efficient and expeditious flight inspections require preflight preparations and actions of facilities maintenance personnel. These preparations include the following actions:

b. Standby Equipment. › (2) Some inspections may only require the checking of one equipment.

(1) Ensure Air Traffic is notified when a facility will be unusable during a flight inspection and an appropriate NOTAM or ATIS information alerts users that flight inspection is in progress.

(2) Provide adequate two-way radio communications equipment and power source at facility sites.

(3) Ensure that all facility equipment is calibrated in accordance with technical orders.

(4) Ensure personnel will be available to make corrections and adjustments.

(5) Provide transportation to move flight inspection equipment and personnel.

(6) Provide accurate facility data for new or relocated facilities.

b. Flight personnel. Accomplished the following actions prior to the flight inspection:

(1) Ensure that all flight inspection equipment is calibrated and operational.

(2) Brief Facilities Maintenance personnel.

(3) Conduct crew briefing.

(4) Obtain maps, charts, equipment, data sheets, etc.

(5) Review the status, limitations, and characteristics of the facility. Ensure that all publications and records agree with the results of the latest flight inspection, and all applicable restrictions are accurate.

(6) Brief the air traffic control (ATC) personnel about the areas and altitudes to be flown during the flight inspection maneuvers and of possible transmitter changes.

17. Flight Inspection. Perform the flight inspection in accordance with the procedures in the appropriate chapter of this order.

a. Operator Proficiency. During flight inspections, qualified personnel will be assigned so operator deviations will not be confused with equipment performance.

b. Standby Equipment. It is necessary to know which system or transmitter is operating so the performance of each can be determined.

(1) When one unit of a dual equipped facility is found out-of-tolerance, it must be identified and removed from service. Identify the unit as transmitter number 1 or 2, channel A or B, serial number, etc.

(2) Some inspections may only require the checking of one equipment. The appropriate facility checklists include the details for each type of facility.

c. Standby Power.

(1) The flight inspector must check the facility on standby power during a commissioning flight inspection if standby power is installed. If a standby power system is installed after the commissioning flight inspection, the flight inspector must check the facility on standby power during the next regularly scheduled periodic inspection. The flight inspector must make comparative measurements to ensure that facility performance is not derogated on the standby power system and that all tolerance parameters for the specific inspection are met. Standby power checks are not required on facilities powered by batteries that are constantly charged by another power source.

17. Flight Inspection. › h. Incomplete Inspections.

(2) It is not necessary to recheck a facility when the standby power source is changed.

d. On-Station Philosophy. Flight inspectors will assist in resolving facility deficiencies and restoring the facility to service prior to departure.

e. Restrictions. When a facility parameter does not meet established tolerances or standards, the flight inspector must perform sufficient checks to determine the usable area of the facility. This data will be the basis of restrictions, NOTAM(s), and procedural redesign.

f. Spectrum Engineering Services Restrictions. Facilities assigned a spectrum management restriction will be classified as “Restricted” and identified on the Facility Data Sheet. This restriction remains in effect even when the facility performance indicates no interference exists. Do not remove published spectrum management restrictions based on flight inspection results.

g. Adjustments. Requests for adjustment must be specific. The flight inspection crew will furnish sufficient information to enable maintenance personnel to make adjustments. Adjustments which affect facility performance must be rechecked by flight inspection. Flight inspection certification must be based on facility performance after all adjustments are completed.

h. Incomplete Inspections. When an inspection on a commissioned facility is halted with the equipment in an abnormal condition due to aircraft malfunction, weather, etc., maintenance personnel and the flight crew will discuss the facility condition and the remaining checks. If the facility maintenance handbooks allow adjustments of the facility parameter without flight check, and adequate references provide the ability to return to a previously certified setting, the equipment may be returned to service. Classify the inspection as incomplete until the remainder of the checks are completed. When a prescribed inspection checklist item cannot be adjusted within tolerance, the inspection will be terminated, facility status changed to unusable, and the inspection classified as incomplete until the remainder of the checks are completed.

18. Analysis and Evaluation. › b. Recordings.

i. Hazardous and Misleading Information (HMI). During some flight inspections, ground equipment is configured in abnormal conditions radiating false information may be misleading to the pilot. Some of these conditions do not produce a “flag” indication. For ILS facilities, studies have shown the most effective warnings to the pilot are those that produce a flag. IAW FAA Order 6750.49, FAA localizers are required to be turned OFF when glide slopes are transmitting HMI, and glide slopes must be OFF when the localizer is producing HMI. This practice does not apply to routine monitor checks (PM). These actions are backed up by NOTAM action verified by other than the NOTAM originator. Checks requiring these configurations are identified in this order with the following placard:

Flight inspection crews must check for applicable NOTAM(s) remind Maintenance of required shutdowns as needed and monitor ATC communications to other aircraft. If ATC clears an aircraft to use the NAVAID, immediately notify them of the facility’s unusable status.

18. Analysis and Evaluation.

a. Data. Flight Inspection data must be analyzed and evaluated by flight inspection using the tolerances specified in this manual. Recordings made during the flight inspections are the permanent records of facility performance.

b. Recordings. Copies of flight inspection recordings for engineering analysis may be obtained from the Mission Technical Support Group. This is a limited capability and should not be used routinely.

WARNING

Ensure NOTAM is active.

WARNING

Monitor ATC communications for improper

approach clearance to other aircraft.

Misleading information is produced by this

configuration.

HAZARDOUSLY MISLEADING

INFORMATION

a. Actions. › (5) Ensure flight information is published.

c. Alignment Convention. The alignment error of omnidirectional type facilities (VOR, TACAN, DF, NDB, ASR, etc.) will be computed through algebraic addition. The azimuth reference (AFIS, theodolite, map) will be assigned a Positive (+) value, and the azimuth determined by the ground facility will be assigned a Negative (-) value. Thus, with a received VOR radial value of 090.5 and an AFIS/map position of 090.0, the facility error would be –0.5°. Alignment errors may also be referred to as clockwise (positive) and counterclockwise (negative).

d. System Evaluations. Flight inspectors must make maximum use of the capability of the flight inspection system. When a special inspection encompasses only one part of a system, i.e., VTAC/V, ILS/G, or GBAS, the other parts of the system, i.e., VTAC/T, ILS/L, Markers, and DME must be recorded and analyzed on a surveillance basis during appropriate maneuvers. Recorder traces that are set by default to the ON position should not be turned OFF unless they obscure other traces. No additional checks are needed to inspect the additional components, unless an out-of-tolerance condition is found.

e. Publications Review. As part of a periodic inspection, the flight inspector must review the Chart Supplement, DOD IFR Supplement, U.S. Government-produced Approach Charts, and En Route Charts applicable to the facility/procedure. The information available to users must be compared with Facility Data Sheets and chart legends to ensure accuracy of presentation. Report facility data discrepancies to the Aeronautical Information Group and charting errors to the Flight Procedures Office for correction.

19. Post Flight Inspection.

a. Actions. Upon completion of the flight inspection, the flight inspection crew must perform the following actions:

(1) Brief Facilities Management personnel concerning results of the flight inspection. Crew members must report all facility outages to appropriate personnel.

(2) Determine facility status. Crew members must assign a status for the facility (see Chapter 5) and notify the appropriate personnel of the facility status.

(3) Prescribe the issuance and/or cancellation of NOTAM(s) based on the flight inspection (See Chapter 5).

(4) Prepare flight inspection reports that are accurate and describe facility performance and characteristics. Reports must be completed in accordance with FAA Order 8240.36, Flight Inspection Report Processing System, latest revision.

(5) Ensure flight information is published. The flight inspector must provide information for publication to the Aeronautical Information Group or the Instrument Flight Procedures Office. They will notify the National Flight Data Center.

19. Post Flight Inspection. › c. VFR Aeronautical Charts.

b. Flight Information.

(a) Receiver Checkpoints. Provide the following information for receiver checkpoints:

(i.) Airport name; (ii.) Bearing in degrees magnetic from the VOR/TACAN; (iii.) Location and description; and (iv.) Distance and altitude.

(b) VOR Test Facilities (VOT). The following information must be provided for a VOT:

(i.) Facility name (and airport name); (ii.) VOT frequency; (iii.) Type facility (area or airport); and (iv.) Information describing usable area.

c. VFR Aeronautical Charts. Consolidate and transfer all field notes to a clean chart, provided by Aeronautical Charting. Resolve any issues arising from the inspection with VFIP managers and cartographers.

a. International Facilities. › (4) For facilities inspected only to the extent that they support U.S.…

Chapter 5. Facility Status Classification, Notices to Air Missions (NOTAMs),

Records, and Reports

Section 1. Facility Status Classification and Notices to Air Missions (NOTAMs)

1. Introduction. Air navigational and traffic control facilities are expected to be usable within specific limits of distances and altitudes (service volume). Facility status classification and NOTAM(s) will indicate restriction(s) to the expected use of these facilities. The facility status classification indicates the general performance of the facility as determined from each flight inspection. This classification is directed only to the maintenance and/or operating agency. The NOTAM advises the user of any restriction to facility usage.

2. Facility Status Classification. Based on the performance of the facility, flight inspection will assign one of the following status classifications:

• Unrestricted: The status of a facility which meets established tolerances.

• Restricted: The status of a facility which does not meet established tolerances throughout the flight inspection standard service volume (areas must be clearly defined as unusable in a NOTAM).

• Unusable: The status of a facility which is unsafe or unreliable for navigation (a NOTAM must be issued for the facility defining it as unusable).

a. International Facilities. The FAA performs flight inspection of international facilities on a contract or agreement basis and for NAVAIDS supporting U.S.-controlled instrument procedures. International facilities are maintained using the manufacturer’s instructions manual and may have no procedures for accomplishing some checks required by this order. Checks performed under these conditions, while meeting the owning nation’s procedural and maintenance certification requirements, do not encompass all checklist items required of U.S. facilities. Special procedures apply for checks performed under these conditions.

(1) For facilities for which the FAA has flight inspection responsibility, and all checklist items appropriate for the inspection have been completed, the flight inspector must assign a facility status.

(2) For facilities for which the FAA has flight inspection responsibility, and all checklist items appropriate for the inspection have not been completed, the flight inspector must discuss the uncompleted items with the facility manager and annotate the report with a statement that the assigned status applies only to the ICAO Annex 10 signal requirements in the as-left configuration. The assigned facility status must be as applied to usability.

(3) If the check does not meet the requirements of this order or ensure the standards of ICAO Annex 10, the host nation will assign the facility status.

(4) For facilities inspected only to the extent that they support U.S. instrument procedures, no status must be assigned and the report must be annotated as to the limited inspection.

3. NOTAM(s). › f. Out-of-Tolerance Standby Equipment.

(5) List any uncompleted checklist items on the report.

b. Facility Coverage in Limited Areas. When facility coverage throughout the flight inspection standard service volume cannot be checked due to inability to penetrate national borders or restricted airspace, the facility will be classified as RESTRICTED, with the report annotated as to the limited coverage flown. NOTAM and publications action will show the facility as UNUSABLE in the areas not checked.

3. NOTAM(s).

a. General. When a flight inspection necessitates NOTAM action, the flight inspector is responsible for initiating the NOTAM(s). The flight inspector must verify within 24 hours that the appropriate NOTAM(s) were issued and are correct. Find further NOTAM guidance in FAA Order 7930.2, Notices to Air Missions (NOTAM) Handbook (latest edition).

b. Facility NOTAMS. The flight inspector must immediately initiate NOTAM action whenever a facility restriction is found or revised. The inspector must verify that NOTAM(s) are published in the appropriate agency publication.

c. Instrument Flight Procedures. Issue Flight Data Center (FDC) NOTAM(s) if a restriction affects instrument flight procedures, approach minimums, or category (CAT) II or III authorizations. NAVAID NOTAM(s) which impact instrument flight procedures should be coordinated with Aeronautical Information Services (AIS), as restrictions to NAVAID(s) may affect published instrument flight procedures.

d. Facilities Not Requiring NOTAM(s). Do not issue a NOTAM to reflect restrictions found during the flight inspection of radar or direction-finding facilities; however, review the instrument flight procedures to ensure that those requiring ground radar are amended or suspended. Coordinate this action with the procedure designer.

When restricting GBAS facilities, do not issue flight procedure NOTAM(s) unless the restricted area affects procedural use. Document restrictions on the data sheet.

e. Expanded Service Volume (ESV) Facilities. When a facility no longer supports an ESV, the facility is not restricted, but issue a NOTAM for the instrument flight procedures predicated on that ESV.

f. Out-of-Tolerance Standby Equipment. Where one of two transmitters of a facility is restricted due to out-of-tolerance parameters and the other is satisfactory, the satisfactory transmitter may be operated without a NOTAM. However, NOTAM data describing the restriction must be provided to Facilities Maintenance personnel. In the event the restricted transmitter is used, the operating agency must issue the NOTAM.

i. Facility Restrictions. › (4) Localizer/LDA/SDF/TLS Azimuth.

g. NOTAM(s) on Military Facilities (including ships).

(1) The military installation commander has the final authority and responsibility for NOTAM issuance and for facility operations of all military facilities which are not part of the National Airspace System (NAS). The commander may elect to use “For Military Use Only” facilities found unsatisfactory.

(2) Recommend NOTAM (s) involving military facilities or procedures to the appropriate military authority for the airfield, facility, or instrument procedure in question. Initiate NOTAM(s) for U.S. Army instrument procedures within the United States through the NFPG. Any NOTAM action involving U.S. military instrument procedures or facilities overseas should be initiated through the appropriate military authority at the location involved. Military units will issue NOTAM(s) according to existing military regulations and letters of agreement with the appropriate host nation International NOTAM Office.

(3) Do not issue NOTAM(s) on shipboard facilities.

h. Preparation of NOTAM(s).

(1) NOTAM(s) must include facility name, type, component, and the unusable area/altitude. The absence of a specific altitude or distance will denote all altitudes and distances. It is important to include specific information to avoid confusion. The reason for the restriction, (e.g., lack of signal, frequency interference, course structure, alignment, unlocks) serves no useful purpose and must not be included in the text of the NOTAM.

(2) Restrictions to TACAN azimuth are not included in agency publications, but are referred to the military for dissemination as they consider necessary. A copy of each NOTAM issued or recommended for TACAN azimuth restrictions must be retained in the facility file for reference during subsequent flight inspections. The NOTAM preparation for the TACAN azimuth component of a VORTAC is identical to the VOR.

i. Facility Restrictions. Apply the following rules for restricted facility use:

(1) Describe the radials or bearings that are unusable.

(2) Describe the altitude and mileages that are unusable.

(3) VOR/TACAN/VOT/DME/DF/NDB/ASR. Describe radial/bearing from the station in a clockwise (CW) direction, altitude in terms of above or below an MSL altitude, and distance in terms of beyond or within a nautical mile distance.

(4) Localizer/LDA/SDF/TLS Azimuth. Describe laterally in terms of degrees left or right of inbound course and in nautical miles from threshold if the restriction affects the limit of usable signal closest to the threshold. Use distance in nautical miles from the antenna to describe restrictions affecting the usable distance of the facility. Describe altitude in terms of above or below an MSL altitude. Additional reference to DME distances may be used if the DME is part of the SIAP.

j. NOTAM Examples. › (5) Condition 5.

(5) Glide Slope/TLS Elevation. Describe in terms of degrees left or right of inbound course and nautical miles from threshold; restrictions pertaining to altitude must be in terms of above or below an MSL altitude. Ensure the restriction correctly reflects the service volume origin (see Chapter 15). Additional reference to DME distances may be used if the DME is part of the SIAP.

(6) VGSI. For VGSI, describe in terms of nautical miles from threshold and/or degrees left and right of runway centerline any areas of coverage where the facility is unusable.

(7) GBAS. Document restrictions in flight inspection records as follows: For VDB coverage restrictions reference the VDB antenna, describe bearing in a clockwise (CW) direction, altitude in terms of above or below and MSL altitude, and distance in terms of beyond or within a nautical mile distance. For GBAS procedural restrictions describe laterally in terms of degrees left or right of inbound course and in nautical miles from threshold. Describe altitude in terms of above or below an MSL altitude.

(8) Published NOTAM(s) will usually omit, but may include, the “CW” reference. This does not constitute an erroneous NOTAM. The flight inspector must review the published NOTAM(s) and restrictions to ensure they convey the correct meaning.

j. NOTAM Examples. Published NOTAM verbiage may vary from the examples given. FSS or NFDC may abbreviate as applicable. The following are examples of conditions and prescribed NOTAM(s):

(1) Condition 1. All components of a VORTAC are unusable in a specific sector due to out-of-tolerance VOR and TACAN course structure and unusable DME. NOTAM Chicago VORTAC: VOR, DME, and TACAN azimuth unusable, 025 cw 075° beyond 25 nm below 3,500 feet.

(2) Condition 2. A VOR does not provide adequate signal to 40 miles at the required altitudes in various areas. NOTAM Altoona VOR: VOR unusable, 080° cw 100° beyond 18 nm below 3,500 feet; 101° cw 200° beyond 30 nm below 3,500 feet; 201° cw 300° beyond 30 nm below 4,500 feet; 301° cw 350° beyond 15 nm; 351° cw 010° beyond 30 nm below 4,000 feet.

(3) Condition 3. VOR is unusable in various areas below one altitude. Also, the DME is unusable in one sector. NOTAM Yardley VORTAC: VOR unusable below 1,700 feet in the following areas: 250 cw 265° beyond 17 nm; 266 cw 280° beyond 10 nm; and 281cw 290° beyond 17 nm. DME unusable 225 cw 275° in the following areas: Beyond 15 nm below 2,400 feet and beyond 30 nm below 5,000 feet.

(4) Condition 4. A Nondirectional radio beacon is not usable in the Southeast quadrant. NOTAM Bradford NDB: unusable 090 cw 180° beyond 15 nm.

(5) Condition 5. Glide slope tolerances are exceeded at a specific point on the glidepath. NOTAM Ashville Regional, NC: Rwy 16 ILS glide slope unusable below 2,310 feet MSL.

3. NOTAM(s). › k. Required Advisories for Local NOTAM(s).

(6) Condition 6. An ILS localizer exceeds tolerances at 1/2 mile from the runway threshold. NOTAM Hartsville Muni, SC, Rwy 16 ILS unusable from 1/2 nm inbound.

(7) Condition 7. Cat II ILS ceases to meet CAT II criteria. FDC, FI/(P or T), NOTAM William B. Hartsfield, Atlanta Int’l, GA: ILS Rwy 9R, CAT II NA.

Note: FI/P means permanent, and FI/T means temporary flight information.

(8) Condition 8. CAT III ILS localizer exceeds CAT III tolerances in Zone 4. FDC, FI/P NOTAM Charleston AFB/Int’l SC: Rwy 15 ILS, CAT III NA.

(9) Condition 9. CAT II ILS localizer exceeds tolerances in Zone 4. NOTAM New Orleans Int’l, LA: Rwy 28 ILS LOC unusable inside runway threshold.

Note: The localizer is unrestricted.

(10) Condition 10. CAT III ILS localizer exceeds tolerances in Zone 5. NOTAM New Orleans Int’l, LA: Rwy 28 ILS LOC unusable for rollout guidance.

(11) Condition 11. Glide slope does not meet change/reversal tolerances below a point on the glidepath. NOTAM Ashville Regional, NC: Rwy 16, autopilot coupled approaches NA below 2,000 feet MSL.

(12) Condition 12. Localizer does not meet tolerances in the vertical plane. NOTAM Wellsville Municipal Arpt., Tarantine Field Arpt., Wellsville, NY: ELZ LOC Rwy 28, LOC unusable beyond OM above 3,500, at threshold above 500.

(13) Condition 13. Beyond 5° left of LOC course, there are no glide slope clearances above path, and a glidepath is not provided. NOTAM Charlotte/Douglas Int’l, NC: Rwy 36R ILS glide slope unusable beyond 5° left of LOC course.

(14) Condition 14. Precision Approach Path Indicator (PAPI) lights are baffled and unusable beyond 5° right of centerline due to obstructions: NOTAM Heber City-Russ McDonald Fld, UT, RWY 21 PAPI unusable beyond 5° right of runway centerline.

k. Required Advisories for Local NOTAM(s). The flight inspector must notify Air Traffic personnel when the facility is not authorized for use because of flight inspection actions.

Chapter 5. › 6. Reports.

Section 2. Records and Reports.

4. Introduction. This section provides policy for flight inspection reports and records. The flight inspection report provides permanent, historical interpretation of a system’s performance. The report must accurately reflect the operational status of the system, the quality of the signal in space, the instrument flight procedure, and revised obstacle, topographical, and cultural data.

5. Records. Flight inspection files are Federal record material. The standards for their retention and destruction are contained in FAA Order 1350.15, Records Organization, Transfer, and Destruction Standards. A facility Reconfiguration (Special/RF) inspection that meets all the commissioning requirements is considered a Commissioning type inspection for record keeping purposes. Flight inspection reports and source material for reports on all electronically radiated facilities inspected constitute report files that must be archived. Such material must contain, but is not limited to, recorder charts showing facility data used, system status, and self-test results, receiver outputs, and crew inputs affecting measurements. Data logger files must be archived for all inspections utilizing AFIS conducted with a functioning data logger. A functioning data logger should be available prior to the inspection. When logger files are not available for archive, either due to none being recorded or data corruption post flight, state such in the Remarks block of the report. Other material may include data items which are necessary for flight inspection purposes, such as horizon profiles, site drawings, topographic charts, instrument approach/departure procedure charts, photographs, electronic media, and data sheets, aircraft logbooks, VFR Chart field sheets, and obstacle records. PAR, VGSI, and NDB source material is not required to be retained once the report has been archived.

a. General Information. Ensure any information included in the facility file is annotated with the following information:

• Facility identification/type of facility;

• Date(s) of inspection;

• Type of inspection (e.g., periodic);

• Aircraft tail number;

• Crew initials and numbers;

• Recorder calibration;

• Equipment-required flight inspection self-test; and

• Airborne flight inspection system calibrations (i.e., TVPS, and system setup).

b. Facility Data Sheets. The flight inspector must ensure that the facility data reflects the most current information and is sufficient to complete the flight inspection requirements.

6. Reports. The flight inspection report serves as the primary means of documentation and dissemination of the results of each flight inspection. Requirements for the use, completion, and distribution of standard FAA and suitable military flight inspection forms are contained in FAA Order 8240.36, Flight Inspection Report Processing System (latest revision).

6. Reports. › c. VFR Aeronautical Chart field sheet

a. Military Facilities.

(1) Changing a Facility Classification to Restricted or Unusable or Altering a Restriction. When the results of the flight inspection indicate that the facility classification is to be changed to "restricted" or "unusable" or that facility restrictions have changed, land the aircraft, if practical, and discuss the reasons and recommended action with appropriate representatives of the base commander. If it is impractical to land, give a status report to the control tower (on ground or tower frequency) indicating the exact status of the facility (unrestricted, restricted, or unusable) and all discrepancies found. Provide them with suggested wording for any required NOTAM(s). Request acknowledgement of the information.

(2) Where there has been no change in facility performance, inform the control tower (on ground or tower frequency) of the exact facility classification. Again, request acknowledgement.

(3) If a military installation does not have a control tower, attempt to pass the information over any other available air-to-ground frequency that would ensure dissemination of the flight inspection results. If no appropriate air-to-ground frequency is available and it is impractical to land, telephone the appropriate personnel as soon as possible.

(4) In any of the above cases, inform the appropriate military maintenance personnel of any discrepancies discovered, and the resulting facility classification.

b. Reports submitted by Military flight inspectors.

(a) Flight inspection reports of facilities inspected by military flight inspection crews, who have been delegated the authority for execution of the flight inspection mission, must be accepted by the FAA as official flight inspection reports.

(b) Military flight inspectors must assign a classification or status to those facilities for which they have flight inspection responsibility.

Note: Coordination may be in the form of a letter of agreement or may be handled on a case-by-case basis. Coordination with Flight Program Operations Department of Defense (DOD) liaison constitutes full flight inspection authority for the respective facility.

c. VFR Aeronautical Chart field sheet notes and obstacle evaluations are a record of having performed the flight inspection and will be archived with Aeronautical Charting.

Continue reading ↓ 120 of 1052 passages shown