Order 8130.2M Airworthiness Certification of Aircraft
U.S. DEPARTMENT OF TRANSPORTATION
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION ORDER 8130.2M
National Policy
SUBJ: Airworthiness Certification of Aircraft
This order establishes policies and procedures for issuing airworthiness certificates, export certificates of airworthiness, and special flight authorizations for aircraft. This order applies to Federal Aviation Administration (FAA) aviation safety inspectors and certain persons designated to act as representatives of the FAA.
FEDERAL AVIATION ADMINISTRATION ORDER 8130.2M
FAA employees and designees are required to comply with this document. For non-FAA entities, this is a guidance document and conformity with the guidance document is voluntary only. Its content is not legally binding in its own right and will not be relied upon by the Department as a separate basis for affirmative enforcement action or other administrative penalty. Nonconformity will not affect rights and obligations under existing statutes and regulations.
JAMES E
JAMES E
Digitally signed by JAMES E WILBORN WILBORN
Date: 2026.07.22 14:24:51 -07'00' Daniel J. Elgas Aviation Safety Director, Policy and Standards Division, Aircraft Certification Service
Distribution: Electronic Initiated By: AIR-632
07/22/2026
Table of Contents
Paragraph Page
Table of Contents … ii
List of Tables … ixx
List of Figures … xx
Chapter 1 Introduction … 1-1
Chapter 1 Introduction … 1-1
1-1. Purpose of This Order … 1-1
1-2. Audience … 1-1
1-3. Where Can I Find This Order and the Code of Federal Regulations (CFR)? … 1-1
1-4. Showing and Finding … 1-1
1-5. Aircraft Located Outside the United States … 1-1
1-6. Cross Utilization … 1-1
1-7. Explanation of Policy Changes … 1-2
1-8. Cancellation … 1-3
1-8. Cancellation … 1-3
1-9. FAA Forms … 1-3
1-10. Acronyms, Definitions, and Related Publications … 1-3
1-11. Conflicts … 1-3
1-12. Effective Date. This order is effective beginning on July 24, 2026 … 1-3
Chapter 2. Common Policies and Procedures for Issuing an Airworthiness Certificate … 2-1
2-1. Introduction … 2-1
2-1. Introduction … 2-1
2-2. Persons Authorized to Issue an Airworthiness Certificate … 2-1
2-3. Common Procedures for Issuing an Airworthiness Certificate … 2-3
2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers … 2-10
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) … 3-1
3-1. Introduction … 3-1
3-1. Introduction … 3-1
3-2. Common Requirements for Reviewing Aircraft Records … 3-1
3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)) … 3-1
3-4. New Aircraft Manufactured Under a TC Only (§ 21.183(b)) … 3-2
3-5. New Import Aircraft, Foreign SOM (§ 21.183(c)) … 3-2
3-6. Used Aircraft (§ 21.183(d)) … 3-2
3-7. Manned Free Balloons … 3-3
3-7. Manned Free Balloons … 3-3
ii
Chapter 4. Issuing Special Airworthiness Certificates … 4-1
Section 1. General … 4-1
4-1. Introduction … 4-1
4-2. Common Procedures for Issuing a Special Airworthiness Certificate … 4-1
4-3. Flight Operations Outside the United States … 4-1
4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores … 4-1
Section 2. Experimental Airworthiness Certificates … 4-3
Section 2. Experimental Airworthiness Certificates … 4-3
4-5. Introduction … 4-3
4-6. Common Procedures for Issuing an Experimental Airworthiness Certificate (§ 21.191) ...4-3
4-7. Areas of Operation … 4-4
4-8. Multiple-Purpose Experimental Airworthiness Certificates … 4-4
4-9. Former Military Aircraft Operated for Experimental Purposes … 4-5
Chapter 5. Primary Category (§ 21.184) … 5-1
Chapter 5. Primary Category (§ 21.184) … 5-1
5-1. Introduction … 5-1
5-2. General Requirements … 5-1
5-3. New Aircraft Manufactured Under a PC (§ 21.184(a)) … 5-1
5-4 New Imported Aircraft (§ 21.184(b)) … 5-1
5-5 Aircraft Having a Current Standard Airworthiness Certificate (§ 21.184(c)) … 5-1
5-2. General Requirements … 5-1
5-6. Other Aircraft (§ 21.184(d)) … 5-2
Chapter 6. Restricted Category (§ 21.185) … 6-1
6-1. Introduction … 6-1
6-2. Common Requirements … 6-1
6-3. New Aircraft Manufactured as Restricted Category (§ 21.185(a)) … 6-2
6-4. Aircraft Used by or Has a Service History with the U.S. Armed Forces (§ 21.185(b)) … … 6-2
6-2. Common Requirements … 6-1
6-5. Aircraft Previously TC’d in Another Category (§ 21.185(b)) … 6-2
6-6. Recurrent Certificates for Restricted Category Aircraft (§ 21.185(a) or (b)) … 6-2
6-7. Import Aircraft (§ 21.185(c)) … 6-2
Chapter 7. Issue of Multiple Airworthiness Certifications for Restricted Category Aircraft
Chapter 7. Issue of Multiple Airworthiness Certifications for Restricted Category Aircraft
(§ 21.187) … 7-1
7-1. Introduction … 7-1
7-2. Procedures for Issuing Multiple Airworthiness Certificates for an Aircraft … 7-1
iii
Chapter 8. Limited Category (§ 21.189) … 8-1
8-1. Introduction … 8-1
8-2. Procedures for Issuing an Airworthiness Certificate … 8-1
Chapter 9. Light-Sport Category Aircraft (§ 21.190) … 9-1
9-1. Introduction … 9-1
9-1. Introduction … 9-1
9-2. General … 9-1
9-3. Procedures for Issuing a Light-Sport Category Airworthiness Certificate … 9-3
9-4. Changing From an Experimental Purpose to the Light-Sport Category … 9-6
Chapter 10. Experimental Purposes of Research and Development and Showing Compliance
Chapter 10. Experimental Purposes of Research and Development and Showing Compliance
with Regulations (§ 21.191(a) and (b)) … 10-1
10-1. Introduction … 10-1
10-2. Procedures for Issuing an Airworthiness Certificate … 10-1
10-3. Holding an Airworthiness Certificate in Suspension … 10-1
Chapter 11. Experimental Purpose of Crew Training (§ 21.191(c)) … 11-1
11-1. Introduction … 11-1
11-2. Procedures for Issuing an Airworthiness Certificate … 11-1
11-2. Procedures for Issuing an Airworthiness Certificate … 11-1
Chapter 12. Experimental Purpose of Exhibition (§ 21.191(d)) … 12-1
12-1. Introduction … 12-1
12-2. Procedures for Issuing Airworthiness Certificates … 12-1
Chapter 13. Experimental Purpose of Air Racing (§ 21.191(e)) … 13-1
13-1. Introduction … 13-1
13-1. Introduction … 13-1
13-2. Procedures for Issuing Airworthiness Certificates … 13-1
Chapter 14. Experimental Purpose of Market Surveys (§ 21.191(f)) … 14-1
14-1. Introduction … 14-1
14-2. Procedures for Issuing an Airworthiness Certificate … 14-1
14-3. Reducing Flight Hour Requirements of § 21.195(d)(2) … 14-1
Chapter 15. Experimental Purpose of Operating Amateur-Built Aircraft (§ 21.191(g)) … 15-1
Chapter 15. Experimental Purpose of Operating Amateur-Built Aircraft (§ 21.191(g)) … 15-1
15-1. Introduction … 15-1
15-2. General … 15-1
15-3. When Builders or Applicants Contact the FAA … 15-2
15-4. Procedures for Issuing an Airworthiness Certificate … 15-2
Chapter 16. Experimental Purpose of Operating Primary Kit-Built Aircraft (§ 21.191(h)) ...16-1
16-1. Introduction … 16-1
16-1. Introduction … 16-1
16-2. Procedures for Issuing an Airworthiness Certificate … 16-1
iv
Chapter 17. Experimental Purposes of Operating Light-Sport Aircraft § 21.191(i), Operating
Light-Sport Category Kit-Built Aircraft § 21.191(k), and Operating Former Light-Sport Category Aircraft § 21.191(l) … 17-1
17-1. Introduction … 17-1
17-1. Introduction … 17-1
17-2. General … 17-1
17-3. Procedures for Issuing an Airworthiness Certificate. Follow chapters 2 and 4 of this order and the following: … 17-2
Chapter 18. Experimental Purpose of Operating Former Military Aircraft (§ 21.191(j)) … 18-1
18-1. Introduction … 18-1
18-1. Introduction … 18-1
18-2. Procedures for Issuing Airworthiness Certificates.: … 18-1
Chapter 19. Special Flight Permits (§ 21.197) … 19-1
Section 1. Common Policies and Procedures … 19-1
19-1. Introduction … 19-1
19-2. Who May Issue an SFP? … 19-1
19-3. Purposes … 19-2
19-4. Procedures … 19-2
Section 2. Additional Policies and Procedures for Particular Purposes … 19-3
19-5. Production Flight Testing of Aircraft Produced under a TC/PC … 19-6
19-5. Production Flight Testing of Aircraft Produced under a TC/PC … 19-6
19-6. Production Flight Testing of Light-Sport Category Aircraft … 19-7
19-7. Conducting Customer Demonstration Flights … 19-8
19-8. Operation of Overweight Aircraft … 19-9
19-9. Aircraft to Which § 91.409(e) Is Applicable … 19-11
Chapter 20. Provisional Airworthiness Certificates (14 CFR Part 21, Subpart I) … 20-1
Chapter 20. Provisional Airworthiness Certificates (14 CFR Part 21, Subpart I) … 20-1
20-1. Introduction. I … 20-1
20-2. Procedures for Issuing an Airworthiness Certificate … 20-1
Chapter 21. Import Aircraft … 21-1
21-1. Introduction … 21-1
21-2. CAA Assistance with U.S. Airworthiness Certificates for New Aircraft Manufactured Outside the United States … 21-1
21-3. Export Certificate of Airworthiness (Export C of A) … 21-1
21-3. Export Certificate of Airworthiness (Export C of A) … 21-1
21-4. Procedures for Issuing an Airworthiness Certificate … 21-3
21-5. Aircraft with Mandatory Continuing Airworthiness Information (MCAI) … 21-6
Chapter 22. Issuing an Export Certificate of Airworthiness (§ 21.329) … 22-1
22-1. Introduction … 22-1
22-1. Introduction … 22-1
v
22-2. Procedures for Issuing an Export C of A … 22-1
22-3. Unassembled Aircraft … 22-4
22-4. Approval of Alterations … 22-4
22-5. Multiple Categories … 22-5
22-6. Replacement and Correction of FAA Form 8130-4 … 22-5
Chapter 23. Special Flight Authorizations for Foreign Civil Aircraft (§ 91.715) … 23-1
23-1. Introduction … 23-1
23-1. Introduction … 23-1
23-2. Eligibility … 23-1
23-3. Procedures … 23-2
Chapter 24. Other Policies and Procedures … 24-1
24-1. Introduction … 24-1
24-2. Public Aircraft Operations (PAO) … 24-1
24-3. Production Flight Testing of Aircraft Built Under Military Contract … 24-1
24-4. Certification of Aircraft with a Door Open or Removed … 24-1
24-5. Replacement ID Plates … 24-2
24-5. Replacement ID Plates … 24-2
24-6. New Aircraft Manufactured Under § 21.6(b) … 24-3
Section 3. Military Surplus Flight Safety Critical Aircraft Parts, Engines, & Propellers 24-4
24-7. Evaluation … 24-4
24-8. Dual Use FSCAP (New or Used) … 24-5
24-9. Military Unique FSCAP … 24-7
24-10. Dual Use & Unique Military Surplus Engines, Propellers, & their Articles … 24-8
24-10. Dual Use & Unique Military Surplus Engines, Propellers, & their Articles … 24-8
Chapter 25. Administrative Information … 25-1
25-1. Distribution … 25-1
25-2. Authority to Change This Order … 25-1
25-3. Deviations … 25-1
25-4. Suggestions for Improvements … 25-1
25-5. Records Management … 25-1
Appendix A. Completing and Reviewing FAA Forms … A-1
Appendix A. Completing and Reviewing FAA Forms … A-1
Section 1. General Procedures … A-1
A-1. General … A-1
Section 2. Application for U.S. Airworthiness Certificate … A-2
A-2. Completion of FAA Form 8130-6, Application for U.S. Airworthiness Certificate … A-2
vi
Section 3. Standard Airworthiness Certificate … A-4
Section 3. Standard Airworthiness Certificate … A-4
A-3. Completion of FAA Form 8100-2, Standard Airworthiness Certificate … A-4
Section 4. Special Airworthiness Certificate … A-6
A-4. Completion of FAA Form 8130-7, Special Airworthiness Certificate … A-6
Section 5. Light-Sport Category Aircraft/Kit Statement of Compliance … A-12
Section 5. Light-Sport Category Aircraft/Kit Statement of Compliance … A-12
A-5. Reviewing FAA Form 8130-15, Light-Sport Category Aircraft/Kit Statement of Compliance (SOC) … A-12
Section 6. Application for Export Certificate of Airworthiness … A-16
A-6. Reviewing FAA Form 8130-1, Application for Export C of A … A-16
Section 7. Export Certificate of Airworthiness … A-17
Section 7. Export Certificate of Airworthiness … A-17
A-7. Completion of FAA Form 8130-4, Export Certificate of Airworthiness … A-17
Appendix B. Documents for Review and Forwarding … B-1
B-1. Introduction … B-1
B-2. Airworthiness Certification Files … B-1
B-3. Review Certification Files … B-1
B-4. Forward Certification Files to FAA Aircraft Registry … B-2
Appendix C. Program Letters … C-1
Appendix C. Program Letters … C-1
C-1. General … C-1
C-2. Program Letter Content … C-1
C-3. Proprietary Information … C-4
C-4. Additional Considerations for Research & Development (§ 21.191(a)) … C-4
C-5 Additional Considerations for Operating Former Military Aircraft (§ 21.191(j)) … C-5
C-6 Space Support Vehicles … C-5
Appendix D. Issuing Operating Limitations with Special Airworthiness Certificates … D-1
Appendix D. Issuing Operating Limitations with Special Airworthiness Certificates … D-1
D-1. Introduction … D-1
D-2. General … D-1
D-3. Phase I Operating Limitations … D-1
D-4. Procedures for Creating Operating Limitations … D-1
D-5. Requests to Add, Modify, or Omit a Limitation, and Required Coordination … D-2
D-6. Review with Applicant … D-4
vii
8130.2M
07/22/2026
Appendix E. CAA Assistance with U.S. Airworthiness Certificates for New
Appendix E. CAA Assistance with U.S. Airworthiness Certificates for New
Aircraft Manufactured Outside the United States … E-1
E-1. Introduction … E-1
E-2. Applicability … E-1
E-3. Procedure … E-1
Appendix F. Sample Special Flight Authorizations … F-1
Appendix G. Limitations for Operation of an Aircraft with a Door Removed … G-1
Appendix H. Acronyms … H-1
Appendix H. Acronyms … H-1
Appendix I. Definitions … I-1
Appendix J. Related Publications … J-1
Appendix K. FAA Form 1320-19, Directive Feedback Information … K-1
viii
List of Tables
Table Page
Table 1-1. FAA Forms Completed by the FAA Under This Order … 1-4
Table 8-1. Sample of Limited Category TCs … 8-2
Appendix K. FAA Form 1320-19, Directive Feedback Information … K-1
Table B-1. Standard Airworthiness Certificates: Documents for Review and Forwarding
to the Registry … B-3
Table B-2. Special Airworthiness Certificates: Documents for Review and Forwarding
to the Registry … B-5
Table D-1. Operating Limitations … D-5
ix
List of Figures
Figure Page
Figure 2-1. Common Steps for Issuing an Airworthiness Certificate … 2-14
Figure A-1. Sample FAA Form 8100-2, Standard Airworthiness Certificate … A-6
Figure A-2. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Restricted Category Aircraft … A-9
Figure A-3. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Research and Development … A-10
Figure A-4. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Special Flight Permit for Production Flight Test and Customer Demonstration … A-11
Figure A-5. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Light- Sport Category Aircraft Certificated Under § 21.190 … A-12
Figure A-6. Sample FAA Form 8130-7, Special Airworthiness Certificate, Experimental Light- Sport Category Aircraft Certificated Under § 21.191(k) and (l) … A-13
Figure A-9. Sample FAA Form 8130-4, Export Certificate of Airworthiness … A-30
Figure C-1. Sample R&D/Exhibition/PAO Applicant Program Letter for a Special Airworthiness Certificate … C-5
Figure F-1. Sample SFA for the Flight of an Aircraft to a Place Where Repairs or Alterations Are to Be Made … F-1
Figure F-2. Sample SFA for the Flight of an Aircraft to a New SOR (This Format Is Generally Applicable to a Single Aircraft Authorization for Ferry Flights) … F-3
Figure F-3. Sample SFA for the Purpose of Flight Testing … F-5
Figure F-4. Sample Blanket SFA for Customer Crew Training … F-7
Figure F-5. Sample SFA for Export Delivery … F-9
Figure F-6. Sample Blanket SFA for Delivering Aircraft for the Purpose of Export Delivery.F- 11
Figure F-7. Sample SFA for the Purpose of Demonstration … F-12
Figure F-8. Sample SFA for Participating in Aviation Events … F-14
Figure G-1. Sample Limitations for Operation of an Aircraft with a Door Removed … G-1
x
Chapter 1 Introduction
1-l. Purpose of This Order. This order establishes policies and procedures for issuing:
• FAA Form 8100-2, Standard Airworthiness Certificate, • FAA Form 8130-7, Special Airworthiness Certificate, • Special flight authorizations (SFA), • FAA Form 8130-4, Export Certificate of Airworthiness (export C of A), and • Experimental certificates and special flight permits for OPA or UAS, when used in conjunction with Order 8130.34, Airworthiness Certification of Unmanned Aircraft Systems and Optionally Piloted Aircraft.
Chapter 1 Introduction
1-2. Audience. FAA manufacturing and airworthiness aviation safety inspectors (ASI) and certain persons designated to act as representatives of the FAA. Airworthiness ASIs must also refer to FAA Order 8900.1, Flight Standards Information Management System, for related policies and procedures.
1-3. Where Can I Find This Order and the Code of Federal Regulations (CFR)? This order and CFRs specified in this order are available on the FAA public website, FAA Dynamic Regulatory System (DRS).
1-4. Showing and Finding. In seeking a certificate or an authorization under this order, an applicant is responsible for presenting evidence necessary to show compliance with applicable requirements to the satisfaction of the FAA; that is, the burden of proof is on the applicant. The FAA is responsible for reviewing and inspecting the applicant’s evidence to make findings of compliance with applicable requirements. If an applicant’s evidence is insufficient to enable the FAA to make its findings, reviews and inspections may be stopped until the applicant presents new evidence to support the FAA’s findings.
1-5. Aircraft Located Outside the United States. Except for issuing an airworthiness certificate under paragraph 21-2 of this order, before processing an application for a certificate under this order for an aircraft located outside the United States, the issuing office must find that the activity can be accomplished without placing an undue burden on FAA resources. Using designees to issue a certificate under this order for an aircraft located outside the United States, would not constitute an undue burden on the FAA but must be authorized in accordance with FAA Order 8000.95, Designee Management Policy.
1-6. Cross Utilization. The FAA performs a variety of functions in issuing certificates and authorization under this order. Many of these functions should be accomplished via coordination among manufacturing, airworthiness, operations ASIs, air traffic, and
other FAA stakeholders with expertise in particular subject matters. Consult with other FAA offices as necessary.
1-7. Explanation of Policy Changes. The following changes are included in this revision.
a. This revision incorporates extensive changes throughout the document. Users should perform a complete review of this revision.
b. This revision implements related provisions of the Modernization of Special Airworthiness Certification (MOSAIC) final rule, which amended Title 14, Code of Federal Regulations (14 CFR), Parts 1, 21, 22, 36, 43, 45, 61, 65, 91, and 119, affecting:
(1) The design, manufacture, certification, operation, maintenance, and alteration of light-sport category aircraft.
(2) Special purpose operations for restricted category aircraft.
(3) The duration of experimental airworthiness certificates for the purposes of showing compliance with regulations, research and development, crew training, and market survey.
(4) Eligible purposes for experimental aircraft with the new purpose of operating former-military aircraft under § 21.191(j).
(5) Operating limitations in 14 CFR Part 91 for light-sport and restricted category aircraft and for experimental aircraft, including experimental aircraft engaged in space support vehicle flights.
c. Other significant changes to this order include:
(1) Added the definitions of “space support vehicle” and “space support vehicle flight.”
(2) The acronyms “ELSA” and “SLSA” were removed throughout the order to align with the removal of the definition of light-sport aircraft in § 1.1.
(3) Chapters 9 and 17 were rewritten to align with new rules for light-sport category aircraft and experimental kit-built and former light-sport category aircraft, respectively.
(4) Chapter 18 was added for the new experimental purpose of operating former military aircraft under § 21.191(j).
(5) Most operating limitations in appendix D, Table D-1, were revised.
(6) Removed all provisions related to FAA approval of production certificate holder’s and modifier’s procedures for operating experimental aircraft.
1-8. Cancellation. The following are canceled upon the effective date of this order:
a. FAA Order 8130.2L, Airworthiness Certification of Aircraft, dated 01/30/2026.
b. All clarification, deviation, and policy memorandums issued for Order 8130.2 before the effective date of this order.
1-9. FAA Forms. Table 1-1 of this chapter lists forms the FAA completes under this order.
1-10. Acronyms, Definitions, and Related Publications. Lists of acronyms and definitions are provided in appendix H and appendix I, respectively. Additionally, this order references related publications; unless otherwise stated, it always refers to the latest revision. See related publications listed in appendix J.
1-11. Conflicts. If a conflict exists between this order and an applicable bilateral agreement, follow the bilateral agreement.
1-12. Effective Date. This order is effective beginning on July 24, 2026.
Table 1-1. FAA Forms Completed by the FAA Under This Order
Form Number Title Source FAA Form 8100-1 Conformity Inspection Record FAA public website
FAA Form 8100-2 Standard Airworthiness Certificate
AWC or FAA employee website for fillable PDF format
FAA Form 8130-1 Application for Export Certificate of Airworthiness
AWC or FAA public website
FAA Form 8130-4 Export Certificate of Airworthiness
AWC or FAA employee website for fillable PDF format
FAA Form 8130-6 Application for U.S. Airworthiness Certificate
AWC or FAA public website for fillable PDF format
FAA Form 8130-7 Special Airworthiness Certificate
AWC or FAA employee website for fillable PDF format FAA Form 8130-10 Surplus Military Aircraft Inspection Record FAA public website
FAA Form 8130-15 Light-Sport Category Aircraft/Kit Statement
of Compliance
FAA employee website for fillable PDF format
Chapter 2. Common Policies and Procedures for Issuing an Airworthiness
Chapter 2. Common Policies and Procedures for Issuing an Airworthiness
Certificate
2-1. Introduction. This chapter provides common policies and procedures for issuing, amending, exchanging, and replacing standard and special airworthiness certificates. Additional classification-, category-, and purpose-specific procedures for issuing an airworthiness certificate are included in subsequent chapters of this order. This chapter does not apply to the issuance of a special flight permit (SFP) except as referenced by chapter 19 of this order.
Note: Where there are differences between common procedures and additional specific procedures, the specific procedures take precedence.
Note: At a minimum, document completed inspections on FAA Form 8100-1, Conformity Inspection Record, per the instructions on the back of the form, to include all applicable requirements found in Paragraph 2-3 (a through i) and in addition, for Experimental Certificates, document all applicable requirements found in Chapter 4 Section 2 of this Order.
2-2 . Persons Authorized to Issue an Airworthiness Certificate.
a. ASIs. FAA ASIs are authorized to issue airworthiness certificates. Manufacturing ASIs in the Aircraft Certification Service (AIR) are primarily responsible for original certifications, while airworthiness ASIs in the Flight Standards Service (AFS) are primarily responsible for recurrent certifications.
b. Delegation. The FAA may delegate the issuance of an airworthiness certificate per 14 CFR Part 183 and the FAA Order 8000.95, Designee Management Policy.
c. Original and Recurrent Airworthiness Certifications.
Note: Appendix I of this order contains definitions of original and recurrent certification and other terms.
(1) An AWC application for an original airworthiness certificate must be assigned to an AIR CM Section. When the AIR CM Section is unable to perform the certification activity, it may request assistance from a flight standards office. If the flight standards office agrees to conduct the activity, the AIR CM Section may reassign the AWC application to that office.
(2) Certain airworthiness certification tasks must remain with the AIR CM Section and should not be delegated to a designee, including:
(a) Issuing the first special airworthiness certificate for a new light-sport category aircraft model, including prototype flight testing under 14 CFR 21.191(a).
(b) Issuing the first special and the first standard airworthiness certificate for an
aircraft intended to support a new or amended type certificate (including supplemental type certificate) or production approval.
(c) Advising applicants about obtaining a type certificate, amended type certificate (including supplemental type certificates), production certificate, or inclusion on the “FAA Make/Model Directory for light-sport category aircraft,” which can be accessed at https://www.faa.gov/aircraft/gen_av/light_sport.
(d) Issuing a Special flight permit for production flight testing issued to a light-sport
category manufacturer or production certificate manufacturer.
(3) Processing an application for an experimental airworthiness certificate used to show compliance with regulations is primarily the responsibility of the AIR CM section. In remote areas or under special circumstances, or when a project requires specialized airworthiness oversight, the AIR CM section manager should request that the Flight Standards office manager assign an airworthiness ASI. The selected inspector must possess experience in type certification programs of a type and complexity comparable to the certificate being requested.
(4) When an application is submitted through the FAA's AWC system for a recurrent airworthiness certification, it is normally routed to a flight standards office. However, certain aircraft associated with AIR-managed certification or production projects should be handled by an AIR CM Section instead. These offices support aircraft involved in projects managed by organizations such as:
(a) Holders of a type certificate.
(b) Holders of a production certificate.
(c) Organizations performing approved aircraft modifications (for example, under supplemental type certificate projects).
In those situations, the AIR CM Section should issue the recurrent airworthiness certification rather than referring the application to flight standards. This division of responsibility is part of the FAA's broader airworthiness certification framework and reflects the involvement of Aircraft Certification Service offices in managing certain certification and production-related projects.
Note: For original or recurrent certifications not previously described in this section, the managers of the responsible AIR and AFS offices should coordinate to establish a mutual agreement on which office is responsible for certificate issuance. Airworthiness and manufacturing ASIs must notify their managers of these situations so that responsibility for certificate issuance can be determined.
Note: As a courtesy, the responsible CM Section may notify the geographic AFS office of any unusual or novel technologies or operations presented by an applicant during an original airworthiness certification. FAA offices are encouraged to jointly identify and resolve risk mitigation of unusual or novel technologies or operational procedures.
2-3. Common Procedures for Issuing an Airworthiness Certificate. Common procedures for issuing an airworthiness certificate are illustrated in Figure 2-1 of this chapter and specified in this paragraph.
a. The Airworthiness Certification Application (AWC).
(1) AWC provides an electronic means to process an application for certain certificates and authorizations under this order. ASIs, designees, and organization designation authorization (ODA) unit members must establish an account, process FAA Form 8130-6, issue standard and special airworthiness certificates, FAA Form 8130-1, and denials using AWC. Unless otherwise stated in this order, all requirements concerning completion of FAA Forms 8130-6 and 8130-1 must be accomplished in AWC. Advisory Circular 21-12, Application for a U.S. Airworthiness Certificate, provides additional information for using AWC for FAA Form 8130-6. This order provides additional information for completing FAA Form 8130-1.
(2) The use of AWC by applicants is not mandatory but is the preferred method for application submission. If an applicant is unable or elects not to submit the application in AWC, the FAA will upload to AWC the hard copy of the application from the applicant and transcribe the information to AWC. The ASI must include a statement that the application information was entered on behalf of the applicant. When completing the application on the Documentation-Certification page of AWC, enter the following statement in the SIGNATURE block of section III, OWNER’S CERTIFICATION: “Application information entered on behalf of the applicant by (Name), (Title). Original attached.” In such cases, do not sign the hard copy or the uploaded application from the applicant, but digitally sign appropriate sections of Form 8130-6 generated by AWC. Per paragraph B-4 of this order, submit both the application signed by the applicant and the AWC-generated application to the FAA Registry (hereafter referred to as Registry).
(3) Access AWC portals as follows. For ASIs, register on the FAA ASI AWC Internal portal. For ODA unit members and designees, register on the External ODA/Designee AWC Portal; follow the prompts for “Login/New User Sign-Up.” Contact the AWC Help Desk at [email protected] for help with access problems.
(4) You may only issue airworthiness certificates and operating limitations outside of AWC in the event it is unavailable due to FAA network or internet outage, or in instances of remote locations where certification activity is being conducted and internet is not accessible. In such cases, revert to the paper process (or portable document format (PDF) equivalent (see table 1-1)) to document and capture data, process applications, and issue certificates. Once AWC is available and accessible, upload documents you created offline to AWC using the Upload Approval page in AWC and use the comments block to record what you uploaded and the reason for issuing the certificate outside of AWC.
b. Review Application.
(1) With the exception of an exchange or replacement airworthiness certificate as described in paragraph 2-4, a properly completed FAA Form 8130-6, Application for U.S. Airworthiness Certificate, is required to begin the process of issuing an airworthiness certificate. Review FAA Form 8130-6 to verify that the applicant completed the form properly. Refer to FAA AC 21-12 for related guidance as necessary.
(2) Letter of Authorization/Agent Letter. If an agent completed the application, verify that the aircraft's registered owner provided a notarized agent letter of authorization and that the information in this letter is consistent with the application. A copy of the notarized agent letter is acceptable to upload in AWC.
Note: Requirements and forms of notarization vary among countries.
(3) Type Certificate Data Sheet (TCDS). For an application for an aircraft in a category that requires a type certificate, review the applicable TCDS or aircraft specification to verify that the aircraft is eligible for issuance of the requested airworthiness certificate by make, model, and serial number (S/N). An aircraft listing maintained by the responsible certification branch may consist of aircraft model and S/Ns of newly manufactured aircraft that are not yet listed on the TCDS. If none of these documents clearly show the eligibility of the applicant’s aircraft by make, model, and S/N, contact the responsible certification branch to verify eligibility.
Note: DRS contains TCDSs and aircraft specifications. Terms for type certificate data have changed over time, including aircraft specifications and TCDS. See the latest version of FAA Order 8110.4, Type Certification, for further information.
Note: For restricted category aircraft, refer to FAA Order 8110.56, Restricted Category Type Certification. The TCDS format for military surplus aircraft includes approved serial numbers instead of eligible serial numbers typically used for aircraft manufactured under a production approval. The applicant may include the list of approved serial numbers in the TCDS, or in a separate FAA-approved report referenced in the TCDS, stating that the serial number report contains only the approved serial numbers.
c. Review FAA Airworthiness Records on File at the Registry. This review includes reviewing the owner information that was submitted on FAA Form 8130-6 and in AWC.
(1) Current Registration. Access the Registry to verify that the aircraft is currently registered per 14 CFR Part 47.
(a) Except for paragraphs (b) through (d), the aircraft is registered when an inquiry of the Registry shows that the nationality and aircraft’s registration number (registration mark), hereafter referred to as the N-number, is “assigned” and the status is “valid” or “valid-asgn to mfr.”
(b) For a new owner of a used aircraft, lag time in processing the application for registration may result in records of ownership within the Registry database that lag
actual transfers in ownership from one United States owner to another. In such cases, the prior owner remains the registered owner of record within the Registry’s database, and registration by the current owner may only be verified as part of the aircraft records review under paragraph 2-3.e.
(c) For a manufacturer’s temporary N-number, the aircraft is considered registered when an inquiry of the Registry shows that the N-number is “reserved,” and the status is “manufacturer (temp).”
(d) For the assignment of a new special registration number, the aircraft is registered when an inquiry by the Registry shows that the “present registration number” is “assigned,” and the status is “valid” or “pending.”
Note 1: When searching the Registry for antique or replica aircraftdisplaying nationality and registration marks as provided for under 14 CFR 45.22(b), omit the inserted symbol allowed by § 45.22(b).
Note 2: For a recurrent certification, including previously exported aircraft returning to the United States, you may retrieve permanent aircraft records from the Registry using the aircraft make, model, and S/N. For aircraft that do not have a data plate or S/N, you may retrieve records using the N-number or prior N-number for previously exported aircraft returning to the United States.
(2) Prior Denials. Except for new aircraft, check the Civil Aviation Registry Electronic Service (CARES), or order a copy of the aircraft record to determine if the FAA previously issued a denial for this aircraft. If previously denied, verify that the reasons for the denial have been corrected, and record the action taken to clear the denial on the FAA Form 8100-1, Conformity Inspection Record.
d. Identify Potential Safety Hazards. Review available information as necessary to assist you in becoming familiar with the aircraft, aircraft engine, propeller models, and potential safety hazards. For example, review information as applicable and necessary to understand the manufacturer/builder; configuration; installed equipment; novel or unique features, characteristics, or systems; recent customer findings for new aircraft deliveries; recent quality escapes for new aircraft; histories of service difficulties, incidents, and accidents; ownership history of the aircraft; and potential for degradation from long-term storage. Designees should review the designee alert list for any pertinent information. The "Designee Alert List" is found in AWC under the "Announcements" tab.
Note: The National Transportation Safety Board (NTSB) maintains a searchable database of accidents and incidents involving civil aircraft.
Note: For rotorcraft, review guidance on the Congressional mandate for rotorcraft crash-resistant fuel systems. Refer to AIR Memo No. AIR-600-20-600-PM04 latest revision.
e. Review Aircraft Records.
(1) Registration. Review the certificate of aircraft registration to verify that the aircraft is currently registered and that the information on the registration and application matches. The manufacturer’s name may be abbreviated on the application and/or registration. If the registration does not have an expiration date, the registration is not effective. Evidence of aircraft registration may be shown via any of the following [hereafter referred to as registration]:
(a) Aeronautical Center Form 8050-3, Certificate of Aircraft Registration.
(b) Aeronautical Center Form 8050-6, Dealer’s Aircraft Registration Certificate.
(c) Form REGAR-FAX-4, Temporary Certificate of Registration.
Note: The permanent AC Form 8050-3 and AC Form 8050-6 may be delivered to the registered owner by email or mail. The FAA plans to discontinue issuing temporary certificates (Form REGAR-FAX-4) because the 8050-3 can be emailed the same day.
(d) Aircraft Registration Application, FAA AC Form 8050-1, under the provisions of § 47.31(c).
(e) A copy of Assignment of Special Registration Number, AC Form 8050-64, and the current, AC Form 8050-3, Certificate of Aircraft Registration.
(2) Exemptions. For exemptions that the applicant claims to apply to this aircraft, verify that each exemption is included in DRS and applies to this aircraft make, model, and S/N.
(3) Maintenance Records. Verify the following:
(a) The applicant has all maintenance records required by 14 CFR 91.417.
(b) All maintenance required as of the date you inspect the aircraft is complete,
including compliance with applicable airworthiness directives (AD) and applicable aircraft and component life limits.
(c) For used, type-certificated aircraft, maintenance, preventive maintenance, and alterations were accomplished per 14 CFR Part 43.
(d) If applicable, verify that the aircraft log includes the reinspection date for the
parachute and associated deployment system components.
(4) Weight and Balance. Review the aircraft weight and balance report, including center of gravity (CG) limitations, to verify that it reflects the current configuration.
(5) Manuals. Verify that the applicant has applicable manuals and documents. Applicable manuals and documents may include an aircraft flight manual (AFM), equipment list, Instructions for Continued Airworthiness (ICA), and maintenance manual(s). Such
manuals and documents may not be required for some aircraft certificated under the Civil Air Regulations (CAR).
(6) Flight Testing. Determine if the aircraft has been flight tested, if required, or as necessary to verify the condition for safe operation. As necessary, issue a special airworthiness certificate for showing compliance with the airworthiness regulations (14 CFR 21.127, 21.137(e)(1), 21.189(a)(2), 21.185(d), 22.195(d)(2), and 91.319(b)) per the applicable requirements of this order.
f. Inspect Aircraft. Physically inspect the aircraft to verify−
(1) Nationality, Registration, and Special Marks. The nationality and registration marks (N-number) meet the requirements of §§ 45.21 through 45.31.
(a) Size. When verifying an N-number is the proper size, verify the height of the marks were measured vertically. The font may be slanted, but do not use the length of the slant line to determine the height of the numbers.
Note: If a surface authorized for displaying required marks under § 45.25 is not
large enough to display full-size marks, § 45.25 allows for marks as large as practicable to be displayed. Assessing “as large as practicable” requires judgment based on the aircraft make/model. For example, for some strongly contoured surfaces, smaller marks may be more legible and, therefore, more practicable than the largest marks that could fit on that surface.
(b) Legibility, Style, Borders, and Shading. The N-number must be legible and written in capital Roman letters without ornamentation. Borders or shading is allowed only if it makes the number more legible. The color of the registration marks must contrast with the background. The N-number must be legible from 500 feet away when viewing it perpendicular to the side of the aircraft during daylight hours.
Note:Section 45.21(b) prohibits a person from placing on any aircraft a design,
mark, or symbol that modifies or confuses the N-number. Note that this requirement is very broad and includes any feature that would modify or confuse the N-number. For example, N-number paint type, paint color, font type(s), or background patterns must not modify or confuse the N-number.
(c) Display of Foreign Marks for Exporting New Aircraft. Per § 45.31, a person who manufactures an aircraft in the United States for export delivery may display foreign marks on the aircraft as required by the importing state of registry (SOR) of the aircraft while the aircraft is registered in the United States. The manufacturer may operate the aircraft with foreign marks within the United States for testing, demonstration, or delivery; note that these flights are performed under an SFP because the aircraft is registered in the United States.
(d) Marking of certain aircraft with a special airworthiness certificate. Except for unmanned aircraft, when marks include only the Roman capital letter “N,” and the registration number is displayed on limited, restricted, experimental, or
provisionally certificated aircraft, the operator must also display on that aircraft near each entrance to the cabin, cockpit, or pilot station, in letters not less than 2 inches nor more than 6 inches high, the words “limited,” “restricted,” “experimental,” or “provisional,” as applicable. Refer to § 45.23.
Note: Although § 45.23 requires these marks “near each entrance to the cabin, cockpit, or pilot station,” this rule does not specify whether these marks must be inside or outside the aircraft; either is acceptable.
(e) Special Marks for Antique or Replica Aircraft. § 45.22(b) provides special marks for exhibition and amateur-built aircraft.
(2) Product Marking.
(a) The aircraft is identified as prescribed in § 45.11 except for an SFP or an experimental airworthiness certificate issued for the purposes of research and development, showing compliance with regulations, crew training, exhibition, air racing, market surveys, or operating former military aircraft. Each installed aircraft engine, propeller, propeller blade, and propeller hub manufactured under a TC or production certificate is marked per § 45.11.
(b) Product identification (ID) plates include the information specified in § 45.13 and must meet § 45.11. Verify that the make, model, and serial number on the aircraft engine and aircraft propeller product ID plate(s) match the application. Verify that the aircraft make, model, and S/N on the aircraft ID plate match the registration. Note that the builder’s name may be abbreviated on the application and registration.
Note 1: For aircraft manufactured outside the United States pursuant to a § 21.29 TC, the TC and PC numbers on the ID plate may reflect the foreign design and production approval numbers. The ID plate information should provide a means to determine the applicable U.S. TC number if the TC number of the state of manufacture (SOM) is used.
Note 2: In some cases, the FAA has granted regulatory exemptions permitting alternate mounting locations of aircraft ID plates for certain aircraft of qualifying air carriers. For any aircraft whose ID plate is mounted in a location other than that required in § 45.11, verify the provisions of a current regulatory exemption for alternate ID plate location cover this.
(c) When an aircraft has been modified to conform to another make/model, verify that the supplemental ID plate contains the information specified in § 45.13. If the FAA Aircraft Registry has not yet issued the new registration with the new model designation, verify that the aircraft make, and the S/N match the application and current registration. If ownership of the aircraft has not changed, an application for aircraft registration reflecting the new model designation, need not be submitted; the FAA Aircraft Registry will change the model and issue a new registration after receipt of the certification files. Verify that the original ID plate has not been altered in any manner.
(d) Inspect the aircraft and review aircraft records to determine whether a violation of §§ 45.13(c) or (e) is apparent. If a violation of §§ 45.13(c) or (e) is found, deny the airworthiness certificate and initiate an enforcement action.
(3) Conformity to TC. For an application for an aircraft in a category that requires a TC, verify that the aircraft conforms to its TC. This includes conformity to applicable ADs, major repairs, and major alterations. Verify that minor repairs or alterations conform to FAA-accepted data.
(4) Engines, Propellers, and Associated Instruments. Engine(s), propeller(s), and associated instruments have been checked per the manufacturer’s instructions or other FAA-approved instructions, placards, or flight manual supplements.
(5) Systems. Aircraft systems are functioning properly, to the extent necessary, including the flight control and pitot-static systems.
(6) Equipment. The installed equipment, including all equipment on the aircraft equipment list, has been checked and verified as functioning properly.
(7) Instruments and Placards. Instruments and placards are correctly located, installed, and properly marked in the English language. In addition, verify that measurements are displayed in standard U.S. units of measure for those instruments necessary for operation in the U.S. national airspace system (NAS).
(8) Airframe Emergency Parachutes (if installed). Verify that the aircraft log matches the reinspection date for the parachute and associated deployment system components. As applicable, verify that airframe emergency parachutes that are ballistic, assisted, or deployable are properly marked, identified, and within their service dates. Verify aircraft marks clearly identify all explosive devices used in conjunction with ballistic parachutes; marks indicating the aircraft is equipped with explosive devices must be applied externally and be readable from the ground.
(9) Foreign Objects. No foreign objects are present that could pose a safety hazard, such as unsecured laptops, tools, scrap material, or miscellaneous debris.
(10) Airworthiness. The aircraft is airworthy.
g. Document Reviews and Inspections. Document all completed reviews and
inspections on FAA Form 8100-1, per the instructions on the form. Verify that the applicant corrects all unsatisfactory findings and documents those corrections on FAA Form 8100-1 before issuing an airworthiness certificate. FAA Form 8100-1 must be completed even if the action isn’t a full aircraft inspection or a full records review such as for an amended or replacement airworthiness certificate. Inspectors and designees should always record when an airworthiness certificate is issued, regardless of how routine the situation is. This builds a historical record of the aircraft’s certification status over time.
h. Issue Airworthiness Certificate. If you find the aircraft airworthy and all other
requirements are met for the requested certificate:
(1) Complete sections V and VIII of FAA Form 8130-6 per the block-by-block instructions in section 2 of appendix A to this order.
(2) Complete the standard or special airworthiness certificate, as applicable, per the block-by-block instructions in sections 3 or 4, respectively, of appendix A to this order. Review the certificate to verify that it was completed without error.
(3) Maintenance record entry. Make the following statement in the maintenance records: “I find that this aircraft meets the requirements for the certificate requested and have issued a [standard airworthiness certificate or special airworthiness certificate for the purpose(s) of (enter purpose) and operating limitations] dated … [Signature: John Smith, Aviation Safety Inspector, AIR-883].”
(4) Give the completed airworthiness certificate to the applicant. Advise the applicant to display it in the aircraft at the cabin or cockpit entrance so it is legible to passengers or flight crew per § 91.203(b).
Note: In certain circumstances, such as replacements and others deemed appropriate by the local office manager, transmitting the airworthiness certificate by email is permissible.
i. Issue Letter of Denial.
(1) If, after notifying the applicant of all unsatisfactory findings, the applicant does not correct those findings to your satisfaction in a timely manner, write a letter to the applicant denying issuance of the certificate and stating the reason(s) for the denial. Identify which steps may be accomplished to meet the certification requirements if feasible.
(2) Complete sections V and VIII of FAA Form 8130-6.
j. Review Records and Forward to the Registry.
(1) Review your records to verify completeness, accuracy, legibility, and compliance with applicable requirements.
(2) Review and forward certification files per appendix B to this order.
Note: AWC allows a closed certification file to be reopened for corrections within 30 calendar days. Designees must coordinate with their managing specialists, notifying them of the reason for conducting this action. Once the 30 calendar day period has elapsed, an AWC certification file may not be reopened.
2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers.
a. Amendment.
(1) Eligibility. An airworthiness certificate may be amended when there is—
(a) A change in the aircraft model specified on an airworthiness certificate.
(b) An alteration to the aircraft, such as one approved by a supplemental type certificate (STC) or amended TC, that changes the aircraft category specified in block 4 of the standard airworthiness certificate.
(c) A change in the operating limitations for an aircraft with a special airworthiness certificate.
(2) Procedures for Amending an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.e of this order is not required. Review aircraft records as necessary in consideration of the reason for the amendment.
(b) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.f of this order is not required. Inspect the aircraft as necessary in consideration of the reason for the amendment.
Note: In amending a special airworthiness certificate, all operating limitations must be issued per the current version of this order, appendix D, and Table D-1.
b. Exchange.
(1) Eligibility. Owners that hold an unexpired FAA Form 1362A, Certificate of Airworthiness, FAA Form 1362B, Certificate of Airworthiness, or unexpired Form ACA-1362, Certificate of Airworthiness, may apply for FAA Form 8100-2, Standard Airworthiness Certificate, or FAA Form 8130-7, Special Airworthiness Certificate, as applicable.
(2) Procedures for Exchanging an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review Application. The existing certificate serves as the application; an FAA Form 8130-6 is not required.
(b) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.e of this order is not required. Review aircraft records as necessary to verify that the applicant’s request is valid.
(c) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.f of this order is not required. Inspect the aircraft per paragraph 2-3.f(1) and 2-3.f(2)(b) to verify that the exterior aircraft N-registration numbers and ID plate information match the application and registration.
c. Replacement.
(1) Eligibility. The FAA may issue a replacement airworthiness certificate when a certificate is declared lost, has been mutilated, is no longer legible, or contains inaccurate and/or erroneous information, or when the aircraft registration number has changed. If inaccurate and/or erroneous information is discovered on the certificate within 30 calendar days following the issuance of the certificate, and it has been determined that it was caused by the issuing inspector, the managing office may reopen the existing AWC record to correct the error and reissue the certificate. Retrieve the certificate with the error. If inaccurate and/or erroneous information is discovered on the certificate after 30 calendar days, the issuing inspector or managing office should initiate and reissue the certificate as a replacement certificate in AWC and follow the procedures for replacement certificates in this chapter.
All corrected documents and supporting materials required for Registry submission must be forwarded through the AWC portal. When reopening an AWC record to correct FAA-originated errors, the managing office must upload a signed letter or memorandum that: • Identifies the specific corrections being made. • Confirms that any newly issued airworthiness certificate (if applicable) has been verified as placed in the aircraft and that the disposition of the original has been documented. • Confirms that all corrected supporting documents required for Registry submission have been uploaded in AWC and submitted to the Registry. Note: If the error (inaccurate and erroneous info) is from the owner/operator, a replacement does not require an 8130-6. A submitted declaration is acceptable.
(2) Do not issue a replacement airworthiness certificate for the scenarios provided for under paragraph 2-4.a(1) of this order for amending an airworthiness certificate.
Note: Replacing an airworthiness certificate is an administrative function and does not require a finding of airworthiness or conformity. When recording the issuance of a replacement airworthiness certificate on FAA Form 8100-1, refer to this note and record that an aircraft inspection was not required. FAA Form 8100-1 must be completed even if the action isn’t a full inspection (replacement). Inspectors and designees should always record when an airworthiness certificate is issued, regardless of how routine the situation is. This builds a historical record of the aircraft’s certification status over time.
(3) Procedures for Replacing an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review the Request. FAA Form 8130-6 is not required; a signed statement is acceptable. Inspect the signed statement requesting the replacement certificate to verify that it is from the registered owner, his or her agent, or an operator and includes the aircraft registration number, make, model, and S/N, and a valid reason for replacing the certificate. If an agent signs the letter, it must be notarized and a copy sent to the registry per Appendix B.
(b) Review FAA Airworthiness Records on File at the Registry. A replacement airworthiness certificate may be issued if all the information from the lost or mutilated certificate can be positively established from the maintenance records, the certificate's remains, or the Registry. If there is insufficient data on which to base issuance of the replacement certificate, including the original operating limitations, do not issue the replacement certificate; advise the applicant to apply for a new airworthiness certificate.
(c) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3 e of this order is not required. Review records as necessary to verify that the applicant’s request is valid and that the aircraft is eligible for the requested airworthiness certificate. When replacing an airworthiness certificate because the aircraft registration number has changed, review both the registration and, when applicable, Aeronautical Center Form 8050-64, Assignment of Special
Registration Numbers, to verify the aircraft is currently registered and to verify the current N-number.
(d) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3 f of this order is not required. Inspect the aircraft as necessary to verify that the applicant’s request is valid and that the aircraft is eligible for the requested certificate.
(e) Issue Airworthiness Certificate. When issuing a replacement for a special airworthiness certificate, the operating limitations must match the operating limitations on the original certificate verbatim. Only modifications to the operating limitations for correcting administrative mistakes are allowed. When issuing a replacement for a standard airworthiness certificate that lists an exemption or exemptions in block 5, follow paragraph A-3 e to complete block 5.
d. Surrender. Verify that the aircraft owner’s written authorization to surrender the airworthiness certificate states why the certificate is being surrendered. Except for an expired experimental airworthiness certificate, email a digital copy of the authorization and certificate to the FAA Aircraft Registry at [email protected] for retention in the permanent airworthiness files. The original should be destroyed after the digital copy is submitted.
e. Transfer. An airworthiness certificate is transferred with the aircraft (§ 21.179), for example, if there is a change of ownership or transfer of registration.
Figure 2-1. Common Steps for Issuing an Airworthiness Certificate
Review application (2.3.b)
Review airworthiness records
on file at the Registry (2.3.c)
Identify potential safety
hazards (2.3.d)
Review aircraft records (2.3.e)
Inspect aircraft (2.3.f)
Document reviews &
inspections (2.3.g)
Issue airworthiness certificate (2.3.h) or letter of denial (2.3.i)
arro
Review records & forward to
the Registry (2.3.j)
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183)
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183)
3-1. Introduction. This chapter provides policies and procedures for issuing standard airworthiness certificates under § 21.183 for aircraft in the normal, utility, acrobatic, commuter, or transport category; manned free balloons; and special class aircraft designated by the FAA under § 21.17(b).
3-2. Common Requirements for Reviewing Aircraft Records. In addition to the common requirements for reviewing aircraft records in paragraph 2-3.e of this order, the following requirements also apply to certain airplanes per § 21.183:
Note: This list is not exhaustive. Other requirements may apply and require verification during your review of aircraft records, such as § 91.1505, Repair assessment for pressurized fuselages, and § 91.1507, Fuel tank system inspection program.
a. Noise. Per § 21.183(e), for an application to issue an original standard airworthiness certificate, review records to verify compliance with the applicable noise requirements of 14 CFR Part 36 or Part 91, subpart I, as applicable.
b. Emergency Exit. Review records for transport category airplanes manufactured after October 16, 1987, to verify compliance with the passenger emergency exit requirements of § 21.183(f).
c. Fuel Venting and Exhaust Emission. Per § 21.183(g), review records to verify compliance with the fuel venting and exhaust emission requirements of Part 34.
3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)). Aircraft manufactured under a PC are eligible for issuing an airworthiness certificate without further showing in accordance with § 21.183(a). The submission of FAA Form 8130-9 is not required. The FAA may inspect each aircraft to determine conformity with the approved type design. The inspection frequency may be adjusted by the geographic CM Section or the CM branch, which has certificate management responsibility over the certificate holder. Consider the following in adjusting inspection frequencies: recent changes in the aircraft design, the quality system, personnel, and the supply base; and recent customer-identified deficiencies, quality escapes, service difficulties, incidents, and accidents. When inspecting an aircraft, follow the applicable procedures in paragraphs 2-3 and 3-2 and the following:
a. Review Aircraft Records.
(1) Review the PC and the production limitation record (PLR) to verify that the holder is authorized to manufacture the applicable aircraft make and model.
(2) Review the manufacturer’s records to verify that quality system procedures have been completed satisfactorily, including production flight testing of the aircraft.
b. Reserved.
3-4. New Aircraft Manufactured Under a TC Only (§ 21.183(b)). Follow the common procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3- 2 of this order and the following:
a. Review Application.
(1) Verify that the manufacturer is still authorized to manufacture under a TC since such authorizations are of limited duration.
(2) Review FAA Form 8130-9, Statement of Conformity, to verify proper completion and to verify the applicant certifies the aircraft is airworthy and was flight tested. Refer to FAA Order 8110.4 for additional FAA Form 8130-9 information.
b. Review of Aircraft Records.
(1) Review the FAA’s inspection records for each aircraft to verify that any prior findings have been properly addressed.
(2) Review the manufacturer’s records to verify that any interim quality system procedures have been completed satisfactorily, including production flight testing of the aircraft.
(3) Verify that any nonconformities involving material review actions have been resolved through the responsible certification branch before issuing an airworthiness certificate.
c. Inspect Aircraft. You must inspect each aircraft presented for issuance of a standard airworthiness certificate to find the aircraft airworthy. Adjust inspections as necessary for any significant changes in manufacturing systems, procedures, or personnel or when changes have been introduced into the aircraft. Inspect the aircraft to verify conformity to its TC, including applicable ADs. This does not imply that every article must be subjected to a conformity inspection. Conformity inspections of articles should only be conducted when, in the FAA’s judgment, conformity cannot be substantiated by any other means.
3-5. New Import Aircraft, Foreign SOM (§ 21.183(c)). Follow the procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2 and chapter 21 of this order.
3-6. Used Aircraft (§ 21.183(d)). This paragraph applies to issuing a standard airworthiness certificate for a used aircraft, including a surplus aircraft of the U.S. Armed Forces. Follow the common procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2 of this order and the following:
a. Review Aircraft Records.
(1) Review aircraft maintenance records to verify the aircraft was inspected and found airworthy per § 21.183(d)(2) within 60 days before the date of the application. The rule requires the aircraft to have been inspected per the performance rules for 100-hour inspections in § 43.15, meaning the use of a checklist that includes at least the scope and detail of appendix D to Part 43. In lieu of a 100-hour type inspection, it is acceptable for the aircraft to have been inspected with an equivalent
performance standard acceptable to the FAA, such as any inspection program prescribed under § 91.409, if inspected per an approved progressive or continuous airworthiness inspection program, this means all inspections must be current. For aircraft with no manufacturer’s recommended inspection program, the inspection program must be one approved by the FAA. This inspection program must have the equivalent performance standard defined to be eligible for compliance with any aircraft certificate conformity inspection used to issue an airworthiness certificate. Verify that one of the following persons performed this inspection and found the aircraft airworthy:
(a) The manufacturer;
(b) The holder of a repair station certificate issued under 14 CFR Part 145;
(c) The holder of a mechanic certificate as authorized in 14 CFR Part 65; or
(d) The holder of a certificate issued under 14 CFR Part 119 and having a maintenance and inspection organization appropriately rated for the type of aircraft involved.
(2) Surplus Aircraft of the U.S. Armed Forces. Review:
(a) FAA Form 8130-31, Statement of Conformity – Military Aircraft, or its predecessor, FAA Form 8130-2, Conformity Certificate – Military Aircraft. This form is issued to a military service at the time of manufacture to identify deviations from the FAA TC for a new military aircraft that was derived from an FAA, type-certificated aircraft. Verify that any deviations have been corrected. Refer to FAA Order 8110.101, Type Certification Procedures For Military Commercial Derivative Aircraft, concerning the use of these forms.
(b) Military maintenance records to determine if operating limitations were exceeded; if so, contact the responsible certification branch for an airworthiness assessment of all exceedances.
(c) Records of engines, gearbox assemblies, landing gear, instruments, or other articles establishing that they originally conformed to the TC and have been maintained per applicable FAA requirements. Military maintenance and/or repair station records may be used for this purpose.
b. Used, Imported Aircraft. For an application for a standard airworthiness certificate for a used, imported aircraft, refer to chapter 21 of this order for additional related policies and procedures.
3-7. Manned Free Balloons. Follow the applicable procedures for issuing a standard airworthiness certificate in paragraphs 3-3 through 3-6 of this order and the following:
a. Inspect Aircraft. Inspect the aircraft to verify that the applicant is presenting a complete aircraft for issuance of a standard airworthiness certificate. For a manned free balloon, a complete aircraft consists of an envelope with an eligible burner, fuel system, and basket; verify that the combination is allowed per the TCDS. You may not issue a standard airworthiness certificate for an article only.
b. Delivery of New Envelopes. Manufacturers of manned free balloons may deliver a balloon envelope when the envelope is the only article ordered. A manufactured balloon envelope assembled to a burner and basket combination authorized by the TC holder and flight tested is eligible for a standard airworthiness certificate. The envelope, along with the standard airworthiness certificate and the logbook, may be delivered without the burner and basket. The envelope may then be assembled to a different burner and basket per the TC. A person may interchange the burner and basket as a preventive maintenance task described below.
c. Changing the Burner and Basket. A new airworthiness certificate is not required when the aircraft is disassembled, and a different burner and basket combination is installed, as the TC allows. Reassembly of the envelope and bottom-end articles into a complete aircraft may be performed as preventive maintenance under 14 CFR Part 43, appendix A, paragraph (c)(27). The aircraft records must properly reflect the installation of the bottom-end articles and record the new empty weight. The bottom-end components must be in a current “annual or 100-hour” inspection status. The individual records of the bottom-end articles must be maintained.
d. Replacement Envelopes. If an envelope is provided only as a replacement article without obtaining a new aircraft S/N, registration number, or ID plate, the installation of the replacement envelope is a maintenance item under Part 43. This requires appropriate documentation of the work performed and a return to service entry in the aircraft records by a person authorized to perform the maintenance. The aircraft ID plate, S/N, and registration number are carried over from the previous aircraft envelope.
Chapter 4. Issuing Special Airworthiness Certificates
Chapter 4. Issuing Special Airworthiness Certificates
Section 1. General
4-1 Introduction.
a. This section provides common procedures for issuing a special airworthiness certificate but does not apply to SFPs.
b. Additional policies and procedures specific to certain aircraft categories, experimental purposes, and SFPs are provided in subsequent chapters of this order.
Section 1. General
4-2. Common Procedures for Issuing a Special Airworthiness Certificate. Follow the common procedures in paragraph 2-3 of this order for issuing an airworthiness certificate and appendix D to this order for issuing operating limitations. As applicable, include paragraph 4-4 in record reviews and the aircraft inspection.
4-3. Flight Operations Outside the United States. A special airworthiness certificate does not authorize flight operations over a foreign country. However, the FAA may issue the certificate when the applicant intends to operate the aircraft over other countries if the applicant meets the requirements for that certificate. A U.S. special airworthiness certificate is often helpful to a foreign civil aviation authority (CAA) when issuing permission to operate the aircraft in or over its country. If the FAA knows the affected CAA will not permit the operation of the aircraft in or over its country, the FAA cannot deny issuance of the certificate if the applicant has met the requirements for that certificate. In any case, an ASI should make the applicable CAA(s) aware of the aircraft, its category or experimental purpose, and the operating limitations for the aircraft.
4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores. These systems are usually associated with former-military or certain restricted category aircraft.
a. Maintenance of Jettisonable Stores. Verify that the applicant’s inspection program includes maintenance and inspection of jettisonable stores and associated articles.
b. Ejection Seat Systems. Verify that the ejection seat system has been approved for use in the aircraft model by the aircraft manufacturer or by a military service.
c. Procedures for Securing Aircraft. Verify that the applicant has provisions and procedures for securing the aircraft whenever it is parked to prevent inadvertent operations of a system that uses an explosive device.
d. Airport Notification. Verify that the applicant has notified the airport manager or sponsor concerning the presence of jettisonable stores, any explosive devices, and planned operations of the aircraft from that airport.
e. Marks for Explosive Devices. Verify markings on the exterior of the aircraft indicating the aircraft is equipped with permanently installed explosive devices, e.g., explosive devices in ejection seats, ballistic parachutes, and jettisonable systems.
4-1
f. Operations with Jettisonable Stores. Except for certain restricted category aircraft (per the applicable restricted type certificate), only aircraft with an experimental airworthiness certificate for R&D may be operated with a jettisonable store, e.g., external fuel tanks and special weapons, and only for a test that requires jettisoning that store. Limited category aircraft and aircraft certificated for other experimental purposes may carry jettisonable stores or externally mounted equipment if mounted in such a manner that in-flight jettison is not possible. See applicable operating limitations in appendix D for additional information.
Note: MIL-STD-8591 defines two categories of stores: ejected and expendable stores. Both ejected and expendable stores are considered jettisonable for the purposes of this order. Ejected stores are released and pushed away from the aircraft laterally or downward, typically by the action of a cartridge-activated ejector, such as a flare. An expendable store is a store that is normally separated from an aircraft in flight, such as a fuel tank, missile, rocket, bomb, mine, torpedo, pyrotechnic device, sonobuoy, signal underwater sound device, cargo drop container, drone, and other similar items.
4-2
8130.2M
07/22/2026
Section 2. Experimental Airworthiness Certificates
Section 2. Experimental Airworthiness Certificates
4-5 Introduction. This section provides common policies and procedures for issuing
special airworthiness certificates for experimental purposes.
4-6 Procedures for Issuing an Experimental Airworthiness Certificate (§ 21.191).
a. Review Application. Follow the procedures in section 1 of this chapter and the
following:
(1) Verify the program letter meets § 21.193 (see Appendix C of this order for additional guidance):
(a) Verify the program letter clearly describes how the aircraft will be used and that the operation meets a § 21.191 purpose. After demonstrating compliance with § 91.319(b)(1) and (2), the aircraft can be used to support other aircraft in the program or other experimental programs the applicant has underway; if applicable, verify that such support activities are described in the program letter.
Note: Except as provided under §§ 21.191(f) and 21.195, brokering or
marketing of experimental aircraft is not a valid experimental purpose; this includes an individual who manufactures, imports, or assembles an aircraft and then applies for an experimental airworthiness certificate to help sell the aircraft.
(b) Verify the program letter provides enough information to describe the operation, equipment, or test, as applicable for the duration of the certificate. Verify that the level of detail in the program letter is sufficient to enable the FAA to prescribe all appropriate operating limitations. Details include, but are not limited to, gross takeoff weight, ejection seat status (operational or not), and a sufficient description so that a review for modifications can determine the aircraft's configuration, including aircraft previously modified for IFR.
(c) Verify the program letter contains the estimated time or number of flights required for the operation for those experimental purposes specified in § 21.191(a) through (f).
(d) Verify the program letter describes the areas over which the applicant will conduct operations (see paragraph 4-7).
(e) Verify the program letter contains enough data to identify the aircraft, such as the inclusion of registration and serial numbers that match those on the aircraft.
(f) Unless converted from a previously type-certificated aircraft without an appreciable (large or noticeable enough to be measured or observed) change in its external configuration, verify the program letter includes three-view drawings or three-view dimensioned photographs of the aircraft.
Note: If any information in the program letter is marked proprietary, confidential, or company-sensitive, or subject to the Uniform Trade Secrets Act, International Traffic in Arms Regulations (ITAR) or Export Administration Regulations (EAR); or contains any other markings indicating the document is restricted from public or foreign disclosure, return these documents to the applicant and ask them to replace them with information that would not require restrictive labels or restrict disclosure. Do not send documents with such restrictions to the Aircraft Registration Branch.(g) Chapter 17 contains additional information for aircraft certificated for the experimental purpose of operating light-sport category kit-built aircraft.
(2) Multiple Purposes. If the applicant is seeking an experimental airworthiness certificate for multiple purposes, verify the program letter clearly documents all the items listed in paragraph 4-6.a(1) of this order separately for each purpose. In addition, verify the program letter describes any required configuration changes when changing between purposes, including adding or removing equipment and enabling or disabling systems. Configuration changes for different experimental purposes are addressed in appendix D. Configuration changes should be included in the aircraft inspection program. Refer to paragraph 4-8 of this order for additional policies and procedures concerning multiple experimental purposes.
b. Inspect Aircraft. Follow the procedures in section 1 of this chapter and the following:
(1) Inspect the aircraft to verify that the aircraft is marked “Experimental.”
(2) Per § 21.193(g), upon inspecting the aircraft, obtain any pertinent information from the applicant as necessary to safeguard the general public.
(3) Determine if the aircraft is airworthy by finding it in a condition for safe operation.
c. Issue Airworthiness Certificate. Follow the procedures in paragraph 2-3.h.
4-7. Areas of Operation. Per § 21.193(d), applicants must submit a description of the areas over which flights will be conducted. Prior to demonstrating compliance with § 91.319(b), no person may operate an aircraft that has an experimental certificate outside of an area assigned by the Administrator until it is shown that the aircraft is controllable throughout its normal range of speeds and throughout all the maneuvers to be executed; and the aircraft has no hazardous operating characteristics or design features. To enable the Administrator to assign an area, the applicant should specify the area that will be used to show compliance with § 91.319(b). Prior to demonstrating compliance with § 91.319(b), the area must be compliant with § 91.305. Inspectors must evaluate the applicant’s area of operation to determine whether it is suitable for the type of operations described in the program letter and for the experimental purpose. If the area is not suitable, inspectors must inform the applicant. Inspectors may ask the applicant for more information or deny the certificate.
Note: Table D-1 contains an operating limitation for Production Certificate holders which may allow takeoffs and landings outside of § 91.305 areas in certain scenarios. Refer to Table D-1 to determine eligibility.
4-5
8130.2M 07/22/2026
4-8. Multiple-Purpose Experimental Airworthiness Certificates.
An experimental airworthiness certificate may be issued for multiple purposes under § 21.191.
Note: The issuance of multiple-purpose certificates for R&D and showing compliance with regulations should be limited to PC holders; however, this may be extended to modifiers (§ 21.195(c)) when justified.
Note: Multiple certifications for a restricted category aircraft under § 21.187 are not authorized in combination with an experimental airworthiness certificate, as explained in chapter 7 of this order.
a. Options. Use discretion in determining the most appropriate option for the intended use. Available options include issuing individual airworthiness certificates for each experimental purpose, issuing a multi-purpose airworthiness certificate, or limiting airworthiness certificate issuance to one experimental purpose at a time. Including experimental purposes with different durations (§ 21.181) on the same airworthiness certificate is not recommended due to the added burden on the applicant and the FAA of having to re-issue the certificate for the purpose which, otherwise, could have had a longer or unlimited duration. However, if the certificating office determines the aircraft is eligible for multiplepurposes and chooses to put multiple purposes with different durations on the same airworthiness certificate, the experimental purpose with the shortest duration per § 21.181 must be used for the expiry date on the FAA Form 8130-7 to remain in compliance with § 21.181.
b. Configuration Changes. Consider how the aircraft configuration may change when switching between purposes or certificates. This information should be included in the program letter, as it may affect the operating limitations issued and could require additional inspections when changing purposes or certificates. If more than one purpose is requested, verify the operator has adequate maintenance, inspection, and configuration change procedures to ensure the aircraft is in a condition for safe operation when changing purposes.
Example 1: An applicant holding an experimental airworthiness certificate for the exhibition purpose is seeking an additional experimental airworthiness certificate purpose to operate the aircraft as a chase plane in support of an R&D project. An experimental airworthiness certificate for the R&D purpose may be issued to the applicant and both certificates may be held simultaneously. Once the R&D project is completed, no further action is needed as the exhibition certificate remains valid due to its unlimited duration.
Example 2: An applicant for an experimental airworthiness certificate for operating an amateur-built aircraft indicates an intention to race the aircraft. In this case, a single certificate listing both purposes may be appropriate.
4-6
8130.2M 07/22/2026
4-9. Inspection Programs for Certain Experimental Aircraft.
This paragraph applies to former military experimental aircraft that are turbine-powered. Advise the applicant to consider FAA AC 43-209, Recommended Inspection Procedures for Former Military Aircraft, in developing its inspection program.
a. Definitions. Advise the applicant that following definitions are terms that may be used in the development of inspection programs for these aircraft.
(1) Overhaul. Methods, techniques, or practices for disassembling, cleaning, inspecting, repairing as necessary, reassembling, and testing in accordance with approved standards and technical data acceptable to the Administrator. Overhaul should not be confused with life limit.
(2) Life Limit. The finite/retirement time assigned to a component that requires the removal of that component from service.
(3) Shelf Life. A recommended time determined by the manufacturer for removal of a component from service.
b. Inspection Program Submittal Requirements. The applicant should submit the
following material for review:
(1) Proposed Inspection Program. The submitted program for an aircraft may be a current manufacturer’s program, a current military program (preferably North Atlantic Treaty Organization (NATO)), an owner/operator-developed program, or based on a program previously approved for the same make/model. Prior FAA approval of an inspection program does not guarantee an automatic approval for a similar make/model because inspection programs are aircraft-specific and will be identified by the aircraft S/N. Inspection programs are subject to amendment whenever significant changes in operating environment and/or equipment occur.
(2) Operable Ejection Seats. The inspection program for operable ejection seats will be based on a current manufacturer’s or current military program, and will include replacement intervals for shelf-life components such as pyrotechnic cartridges. Shelflife intervals cannot be extended without the manufacturer’s approval.
(3) Required Manufacturer/Military Manuals. If the manuals were not originally published in English, the applicant will submit an English translation of the original manuals. It is to the applicant’s benefit to ensure the translation is performed by a technically competent individual familiar with aviation terms and practices.
(4) Substituting Materials or Replacement Parts. Changes involving the substitution of materials or replacement parts should be in accordance with FAA-accepted procedures or a recognized industry standard, or based on dimensions and technical data provided by the manufacturer or information provided by an appropriate engineering evaluation. Life-limited articles specified in the applicable technical publications pertaining to the aircraft and its articles are complied with in one of the following manners:
(a) Type-Certificated Products. Replacement of life-limited parts required by § 91.409(e) is only applicable to experimental aircraft when the required replacement times are specified in the U.S. aircraft specifications or TCDS.
4-7
(b) Non-Type-Certificated Products. Unless otherwise determined by the FAA, all articles installed in non-type-certificated products operated in the experimental category, in which the manufacturer has specified limits, must include in their program an equivalent level of safety for those articles. Although the FAA recommends adherence to part replacements, achieving an equivalent level of safety for non-type-certificated products is acceptable. The article must be inspected to ensure the equivalent level of safety still renders the product in a serviceable condition for safe operation.
(5) Extension of Component Life Limits. (reference operating limitation #25)
(a) The applicant may submit data, with a request to the FSDO, to extend the life limit on specific components of the aircraft beyond the manufacturer, military, and/or technical order recommended life limits. At a minimum, the data submitted by the applicant should contain:
(1) The original strength, stress, and fatigue data for the aircraft and the pertinent parts, including other parts that may be affected by changes of the life limits and inspection intervals;
(2) The methodology the designers used while developing the life limits and inspection intervals,
(3) The operational history of the aircraft and parts (usage affects life limits and inspection intervals);
(4) The service history of the aircraft and pertinent parts, including any repairs and modifications affecting the strength, stress, and fatigue characteristics of the parts and their effects on the parts’ life limits and inspection intervals;
(5) How the present operational usage differs from prior military usage;
(6) Evidence that the applicant’s inspection/testing techniques, for example, nondestructive inspection/nondestructive testing, are comparable to those used by the military;
(7) Evidence that the methodology chosen by the owner (for example, damage tolerance with inspections versus safe-life with automatic removal) produces at least as safe a product as the military’s approach.
(8) A procedure to inspect the component to some appropriate physical standard, and non-destructive testing, where applicable.
4-8
(b) In cases where the data listed above is unavailable or cannot be substantiated, the components will not be eligible for any extension of life limits.
(6) Extension of Component Recommended Overhaul Times. The owner/operator may elect to continue in service any component that has reached its recommended overhaul time if an approved inspection is implemented that includes a procedure to inspect the component to an appropriate physical standard with a definitive time period for review. Testing to the standard may be accomplished in place where practicable. This inspection procedure will be submitted to the local FSDO to be included in the FAAapproved inspection program. (reference operating limitation #25)
c. Inspection Program Content.
(1) The owner/operator-developed inspection program presented for FAA approval should reference specific details from the appropriate military/manufacturer’s manuals while encompassing the scope and detail of Part 43, appendix D, as appropriate.
(2) As an alternative, a military/manufacturer’s inspection program may be adopted and presented for FAA approval. Specific irrelevant sections may be deleted for aircraft systems that have been removed or deactivated. However, all inspection programs should provide for a complete inspection of the aircraft within the preceding 12 calendar months.
(3) The following items should be a part of an approved inspection program:
(a) Title page that includes the aircraft manufacturer’s name and the aircraft model, serial number, and registration number to which the inspection program applies; and the owner/operator’s name and address.
(b) Table of contents.
(c) Log of revisions.
(d) Method of revision.
(e) List of effective pages.
(f) Introduction that includes the following:
Continue reading ↓ 120 of 577 passages shown