Order 5280.5D Airport Certification Program Handbook
This Order provides FAA personnel with the policies, standards, and procedures for conducting the Airport Certification Program. This Order helps ensure standardization and uniformity in the application of the program and in enforcing Title 14 Code of Federal Regulations (CFR), Part 139, Certification of Airports (Part 139).
National Policy
Distribution: Electronic Initiated by: AAS-300
ORDER NUMBER
5280.5D Effective Date:
11/7/2016
SUBJ: Airport Certification Program Handbook
1 Purpose. This Order provides FAA personnel with the policies, standards, and procedures for conducting the Airport Certification Program. This Order helps ensure standardization and uniformity in the application of the program and in enforcing Title 14 Code of Federal Regulations (CFR), Part 139, Certification of Airports (Part 139).
2 Cancellation. This Order cancels Order 5280.5C, Airport Certification Program Handbook, dated September 8, 2006.
3 Application. This Order applies to all Airport Certification Safety Inspectors for use in enforcing Title 14 Code of Federal Regulations (CFR), Part 139, Certification of Airports.
4 Distribution. This Order is distributed to the division level of the Office of Airport Safety and Standards. the Office of Airport Compliance, and the Office of Airport Planning and Programming; to the branch level of Regional Airports Divisions; to all Airport District Offices; and to the division level of Regional Flight Standards, Air Traffic, Airway Facilities, and Aviation Security offices.
5 Feedback on this Order. If you have suggestions for improving this Order, you may use the Order Feedback form at the end of this Order.
Michael J. O’Donnell Director, Office of Airport Safety and Standards
CONTENTS
Paragraph Page
ii
Chapter 1. Administration … 1-1
1.1 Introduction … 1-1
1.2 Systems for Communicating Information about the Airport Certification Program. ... 1-2
Chapter 2. Certification Process … 2-1
2.1 Purpose … 2-1
2.2 Section 139.1. Applicability … 2-1
2.3 Airport Classifications … 2-1
2.4 Section 139.3, Delegation of Authority … 2-2
2.5 Section 139.5, Definitions … 2-2
2.6 Section 139.7, Methods and Procedures for Compliance … 2-2
2.7 Section 139.101, General Requirements … 2-2
2.8 Section 139.103, Application for Certificate … 2-3
2.9 Section 139.105, Inspection Authority … 2-4
2.10 Section 139.107, Issuance of Certificate … 2-4
2.11 Section 139.109, Duration of Certificate … 2-7
2.12 Section 139.111, Exemptions … 2-8
2.13 Section 139.113, Deviations … 2-8
2.14 Change of Ownership … 2-9
2.15 Section 139.115, Falsification, Reproduction, or Alteration of Applications, Certificates, Reports, or Records … 2-9
Chapter 3. Airport Certification Manual … 3-1
3.1 Purpose … 3-1
3.2 Section 139.201, General Requirements … 3-1
3.3 Section 139.203, Contents of the Airport Certification Manual … 3-1
3.4 Section 139.205, Amendment of the Airport Certification Manual … 3-2
Chapter 4. Inspection Process … 4-1
4.1 Purpose … 4-1
4.2 Types of Inspections … 4-1
4.3 Inactive Status … 4-2
iii
4.4 Schedule of Inspections … 4-2
4.5 Preparation for Initial and Periodic Inspections … 4-4
4.6 Inspection Protocol–General … 4-5
4.7 Phases of the Inspection … 4-7
4.8 Inspection Protocol–Specific Guidance … 4-13
4.9 Section 139.301, Records … 4-13
4.10 Section 139.303, Personnel … 4-15
4.11 Section 139.305, Paved Areas … 4-16
4.12 Section 139.307, Unpaved Areas … 4-18
4.13 Section 139.309, Safety Areas … 4-18
4.14 Section 139.311, Markings, Signs, and Lighting … 4-21
4.15 Section 139.313, Snow and Ice Control … 4-26
4.16 Section 139.315, Aircraft Rescue and Firefighting: Index Determination … 4-27
4.17 Section 139.317 ARFF: Equipment and Agents … 4-28
4.18 Section 139.319. ARFF: Operational Requirements … 4-28
4.19 Section 139.321, Handling and Storage of Hazardous Substances and Materials … 4-36
4.20 Section 139.323, Traffic and Wind Indicators … 4-38
4.21 Section 139.325, Airport Emergency Plan … 4-38
4.22 Section 139.327, Self-Inspection Program … 4-39
4.23 Section 139.329, Pedestrians and Ground Vehicles … 4-40
4.24 Section 139.331, Obstructions … 4-43
4.25 Section 139.333, Protection of NAVAIDs … 4-44
4.26 Section 139.335, Public Protection … 4-44
4.27 Section 139.337, Wildlife Hazard Management … 4-45
4.28 Section 139.339, Airport Condition Reporting … 4-51
4.29 Section 139.341, Identifying, Marking, and Reporting Construction and Other Unserviceable Areas … 4-51
4.30 Section 139.343, Non-compliance Conditions … 4-52
Chapter 5. Compliance and Enforcement Policy … 5-1
5.1 Purpose … 5-1
5.2 General Policies … 5-1
5.3 Investigating Alleged Violations … 5-2
5.4 Compliance Action for Non-Regulatory Issues … 5-6
iv
5.5 Administrative Action … 5-6
5.6 Letter Acknowledging Completion of Corrective Action … 5-8
5.7 Enforcement Action—General … 5-8
5.8 Enforcement Consistency … 5-13
Chapter 6. Accident Investigation Responsibilities and Procedures … 6-1
6.1 Overview … 6-1
6.2 Responsibilities … 6-1
6.3 Investigation Procedures … 6-5
6.4 Safety Recommendations … 6-8
Chapter 7. Inspector Training, Qualifications, and Credentials … 7-1
7.1 Purpose … 7-1
7.2 Background … 7-1
7.3 Policy … 7-1
7.4 Approval Authority … 7-1
7.5 Responsibilities … 7-1
7.6 Criteria for Eligibility … 7-2
7.7 Inspector Training … 7-2
7.8 Aviation Background/Experience … 7-3
7.9 On-the-Job Training (OJT) … 7-4
7.10 Currency Requirements … 7-5
7.11 Temporary Inspection Authorization … 7-5
7.12 ACSI Credentials … 7-6
7.13 Inspector Exchange Program … 7-8
7.14 Recurrent Training (FAA Academy) … 7-8
Chapter 8. Petitions for Exemptions … 8-1
8.1 Purpose … 8-1
8.2 General … 8-1
8.3 Receipt of the Petition for Exemption … 8-1
8.4 Processing the Petition … 8-2
8.5 Analysis of the Petition … 8-3
8.6 Procedures for Granting or Denying the Petition for Exemption … 8-4
8.7 Petition for Reconsideration … 8-5
v
8.8 Exemption Expiration and Petition for New Exemption … 8-5
8.9 Exemptions for Non-certificated Airports with Special Events Triggering Part 139 … 8-5
Chapter 9. Participation in Safety-Related Activities … 9-1
9.1 Purpose … 9-1
9.2 Airport Emergency Plan (AEP) Exercises … 9-1
9.3 Pre-design/Pre-construction Conferences … 9-2
9.4 Inspection of Construction Projects … 9-2
9.5 Joint Planning Conferences (JPCs) … 9-2
9.6 Runway Safety Action Team (RSAT) Meetings … 9-3
9.7 Other Safety-Related Events … 9-3
Chapter 10. Program Evaluations, Staff Visits, and staff REgional liaisions … 10-1
10.1 Purpose … 10-1
10.2 Formal Evaluations … 10-1
10.3 Staff Visits … 10-2
10.4 AAS-300 Staff Regional Liaisons … 10-3
10.5 AAS-300 Evaluation of CCMIS Program Entries … 10-3
Chapter 11. Reports, Correspondence, and Records … 11-1
11.1 Purpose … 11-1
11.2 Correspondence and Reports from ACSIs to Certificate Holders … 11-1
11.3 Correspondence and Reports from Regional Airports Divisions to Headquarters … 11-2
11.4 Correspondence and Reports from Headquarters to Regional Airports Divisions … 11-3
11.5 Airport Certification Records … 11-3
11.6 General Instruction for Completing the Airport Master Record (Form 5010-1) and A-26 and A-110 Remarks … 11-4
11.7 General Instruction for Completing the Airport Certification/Safety Inspection Checklist (Form 5280-4) … 11-5
11.8 Inspection Reports … 11-5
11.9 Certification and Compliance Management Information System (CCMISNet) … 11-5
Appendix A. U.S. Government-Owned Airports Certificated Under 14 CFR
Part 139 … A-1
Appendix B. Application for Certificate (FAA Form 5280-1) … B-1
vi
Appendix C. Airport Operating Certificates … C-1
Appendix D. Certification Action Letter … D-1
Appendix E. Airport Certification Manual Transmittal Letter … E-1
Appendix F. Inspection Confirmation Letter … F-1
Appendix G. Airport Certification/Safety Inspection Checklist
(FAA Form 5280-4) … G-1
Appendix H. Aircraft Rescue Fire Fighting Enhanced Checklist … H-1
Appendix I. Inspection Closeout Letter … I-1
Appendix J. Sample Warning Letter … J-1
Appendix K. Compliance Letter … K-1
K.1 Sample Compliance Letter (Long Format) … K-2
Appendix L. Letter Acknowledging Completion of Corrective Action … L-1
Appendix M. Letter of Investigation … M-1
Appendix N. Investigation Closeout Letter … N-1
TABLES
Number Page
Table 2-1. Airport Classifications … 2-2
1.1 Introduction. › 1.1.4 Definitions.
CHAPTER 1. ADMINISTRATION
1.1 Introduction.
Responsibilities. 1.1.1
1.1.1.1 The Airport Safety and Operations Division (AAS-300) and the Office of Airport Safety and Standards (AAS) are responsible for the publication, revision, and cancellation of material in this Order.
1.1.1.2 To execute the program properly, each Airport Certification Safety Inspector (ACSI) and Regional Airports (600) Division Manager or Regional Planning and Programming (620) Branch Manager must be thoroughly knowledgeable about the program and conversant with the provisions of the Part 139 regulation and this Order.
Note: Not all Regional Offices maintain a 620 Branch Manager position. In such cases, references in this Order to the Regional 620 Branch Manager will apply to the Regional 600 Division Manager.
Objectives. 1.1.2 This Order is intended to—
1.1.2.1 Meet the requirements of the Airport Certification Program, in accordance with 49 United States Code (U.S.C.) 40101 and 44706 and 14 CFR Part 139, Certification of Airports;
1.1.2.2 Facilitate standardized application of program policies and procedures throughout the Regional offices;
1.1.2.3 Provide current program guidance to ACSIs administering the program;
1.1.2.4 Support Regional management oversight of the Airport Certification Program; and
1.1.2.5 Assist ACSIs as they direct and educate airports on the establishment and maintenance of programs designed to enhance and improve airport safety.
Procedures for Updating this Order. 1.1.3 AAS might make additions, revisions, or deletions to this Order to improve the currency, accuracy, and adequacy of the program. Regional 620s and/or ACSIs can submit suggestions for revising the Order along with justifications or rationales for the changes in Memorandum format to AAS-300. The Regional 620 must sign the Memorandum and can send an electronic copy to AAS-300 via email.
Definitions. 1.1.4 See 14 CFR § 139.5 of the regulation for a full list of definitions.
1.2.3 CertAlerts. › 1.2.3.2 AAS-300 distributes CertAlerts to Regional offices and makes…
1.2 Systems for Communicating Information about the Airport Certification Program.
Introduction. 1.2.1 Periodically, AAS-300 must communicate significant changes to the program, clarify the regulation, explain how technological information impacts this program or affects airport safety, or gather information from Regional offices and the airport community. AAS-300 uses various means to communicate and collect program information, including—
1. Policy Guidance (Internal Communication),
2. CertAlerts (External and Internal Communication),
3. Aviation Safety Reporting System (External and Internal Communication), and
4. Runway Safety Program System (Internal Communication).
Policy Guidance. 1.2.2
1.2.2.1 AAS-300 uses Policy Guidance to provide interpretation of Part 139 or the associated Airport 150 series Advisory Circulars to maintain program consistency.
1.2.2.2 Policy Guidance provides interim information that remains in effect until the next edition of this Order is published. Policy Guidance is sequentially numbered, dated, and effective upon receipt.
1.2.2.3 Policy Guidance is distributed to the Director of the Office of Airport Safety and Standards (AAS-1), AAS-300, and Regional Airports Divisions and is made available on the Airports internal employee website.
1.2.2.4 AAS-300 is responsible for developing, updating, and canceling Policy Guidance. However, Regional Division/Branch Managers and ACSIs may recommend new Policy Guidance. (See Paragraph 1.1.3, Procedures for Updating this Order.)
CertAlerts. 1.2.3
1.2.3.1 These publications contain information and updates about airport safety and operations. While non-regulatory in nature, they can be used to disseminate notices of proposed changes in the regulation for airport operators. CertAlerts are numbered by calendar year.
1.2.3.2 AAS-300 distributes CertAlerts to Regional offices and makes them available to the airport community in the Airports section of the FAA website. When AAS-300 issues a CertAlert, it updates the online CertAlert log for that year.
1.2.5 Runway Safety Program System. › 1.2.5.2 The system makes use of two forms to document the details of…
1.2.3.3 The CertAlert log lists the CertAlerts issued by date and numbered consecutively within the calendar year and identifies their current status (e.g., cancelled, revised, or superseded).
1.2.3.4 AAS-300 is the only entity authorized to issue and cancel CertAlerts. ACSIs are encouraged to suggest topics for new CertAlerts to AAS-300 (See Paragraph 1.1.3, Procedures for Updating this Order.)
Note: Regional specialists may author and issue Regional CertAlerts at the discretion of their Division Manager. All Regional CertAlerts must be coordinated with AAS-300 prior to issuance.
Aviation Safety Reporting System (ASRS). 1.2.4
1.2.4.1 This system permits airport users to report events or conditions affecting aviation safety. A full explanation of the ASRS system can be found at http://asrs.arc.nasa.gov and in AC 00-46, Aviation Safety Reporting Program, and the Aeronautical Information Manual (AIM). Funded by the FAA and administered by the National Aeronautics and Space Administration (NASA), ASRS helps the aviation community identify and correct unsafe conditions before they cause accidents.
1.2.4.2 Typically, NASA sends ASRS reports directly to the airport operator or the Regional staff providing oversight to the identified airport. However, when AAS-300 receives an ASRS report, AAS-300 will forward the report to the Regional office, which must review the report and follow up with the associated airport operator as appropriate.
1.2.4.3 Regional offices must provide AAS-300 with the final disposition of the response provided and details of any actions taken with the identified airport to assist with trend and analysis data. Regions should provide AAS-300 with this final disposition for all ASRS reports received.
Runway Safety Program System. 1.2.5
1.2.5.1 The Runway Safety Program Office established a reporting and investigative system designed to address all runway incursions and any increase in the numbers of runway incursions and surface incidents.
1.2.5.2 The system makes use of two forms to document the details of these events and their subsequent investigation.
1. Form 8020-24, Preliminary Vehicle or Pedestrian Deviation (VPD) Report, contains the preliminary information about an event. The Comprehensive Electronic Data Analysis and Reporting (CEDAR) system helps air traffic controllers file a VPD report electronically. The submissions go to the service area Quality Assurance (QA) division to conduct the investigation, making it unnecessary for the local tower to enter the data on the Form 8020-24. QA will gather any
voice tapes and radar tracks and include it in the Air Traffic Organization (ATO) QA Knowledge Services Network.
2. Form 8020-25, Investigation of Vehicle or Pedestrian Deviation Report, is completed next and includes an investigative report and, more important, the resolution of the circumstances surrounding the event. ACSIs use Form 8020-25 to document the investigation, develop recommended actions to resolve the causes, and close out the event.
Chapter 2. Certification Process › 2.3 Airport Classifications.
CHAPTER 2. CERTIFICATION PROCESS
2.1 Purpose. This Chapter establishes the policies and procedures for certificating airports subject to Part 139.
2.2 Section 139.1. Applicability.
The certification requirement is applicable to all airports in every State of the United 2.2.1 States, the District of Columbia, and any territory or possession of the United States at which passenger operations of the following types occur:
1. Scheduled operations by small aircraft designed for more than 9 but less than 31 seats (except for the State of Alaska),
2. Scheduled operations by large aircraft designed for 31 or more seats, and
3. Unscheduled operations by large aircraft designed for 31 or more seats.
The certification requirement is not applicable to heliports, airports operated by the U.S. 2.2.2 Government, airports serving scheduled air carrier operations only because they have been designated as an alternate airport, airports located in the State of Alaska that only serve scheduled operations of small air carrier aircraft and do not serve scheduled or unscheduled operations of large air carrier aircraft, and airports located in the State of Alaska when not serving operations of large air carrier aircraft, unless specified by FAA Headquarters.
Note: Currently, only one U.S. Government-owned airport is certificated under 14 CFR Part 139: Midway Atoll, Henderson Airfield. The airport is owned by the Department of Interior and managed/operated by the U.S. Fish and Wildlife Service. The U.S. Congress has directed the FAA and the Department of the Interior to maintain this airport.
The certification requirement is applicable to the civilian portions of joint-use or shared- 2.2.3 use airports.
The certification requirement is applicable to airports at which 14 CFR Part 380 (Public 2.2.4 Charter) operations occur, pursuant to 49 U.S.C. 41104 (b), Additional Limitations and Requirements of Charter Air Carriers.
2.3 Airport Classifications. Part 139 identifies four airport classifications based on the type of operation and aircraft serving the facility.
Chapter 2. Certification Process › 2.7 Section 139.101, General Requirements.
Table 2-1. Airport Classifications
2.4 Section 139.3, Delegation of Authority. The authority of the Administrator to issue, deny, and revoke Airport Operating Certificates is delegated to the Associate Administrator for Airports, Director of Airport Safety and Standards, and Regional Airports Division Managers.
2.5 Section 139.5, Definitions. See 14 CFR § 139.5 for a full list of definitions.
1. Airport Certification Safety Inspector (ACSI). ACSI are credentialed FAA personnel responsible for conducting periodic airport inspections and ensuring the 14 CFR Part 139 program is carried out in accordance with FAA's Compliance and Enforcement Program. ACSIs investigate potential regulatory violations, recommend enforcement actions, and represent the Administrator.
2. Consecutive Calendar Months. A period of time that ensures uninterrupted succession or following of action. This is an established regulatory definition representing a specific period of time that cannot be waived.
2.6 Section 139.7, Methods and Procedures for Compliance. Certificate holders are required to comply with the requirements of Part 139, Subparts C and D, in a manner authorized by the Administrator. FAA Advisory Circulars (ACs) contain acceptable methods and procedures for complying with Part 139. There are instances where the only applicable guidance is found in an AC and this level of guidance meets the intent of being acceptable to the Administrator. Each AC will specify the applicability guidance and intent; ACSIs should refer to the applicability section when consulting ACs.
2.7 Section 139.101, General Requirements. The operator of an airport identified in § 139.1 must—
Type of Air Carrier Operation Class I Class II Class III Class IV
Scheduled Large Air Carrier Aircraft
X
Unscheduled Large Air Carrier Aircraft
X X
X
Scheduled Small Air Carrier Aircraft
X X X
2.8.3 In addition, an applicant applying for an AOC for the first time… › 2.8.3.1 Surrendering an AOC or Modifying the Class Certificate.
1. Obtain an Airport Operating Certificate (AOC) appropriate to the level of service provided at the airport and
2. Comply with the applicable requirements of Part 139, the AOC, and the Airport Certification Manual (ACM).
2.8 Section 139.103, Application for Certificate.
As specified in § 139.103, the operator of an airport that is required to be certificated 2.8.1 under Part 139 must prepare and submit to the Regional office a Form 5280-1, Application for Certificate 2), and two copies of the ACM in compliance with the applicable provisions of Subpart C. These documents should be submitted far enough in advance of an intended operation to permit a thorough review and subsequent approval of the ACM, an inspection of the airport, and preparation of the AOC and associated correspondence.
Except under Paragraph 2.10.6.1 of this Order, the applicant must provide written 2.8.2 documentation from at least one air carrier committing to initiate air carrier service on a certain date. Regions can verify this information with the applicable Flight Standards District Office or Certificate Management Office.
In addition, an applicant applying for an AOC for the first time must be properly and 2.8.3 adequately equipped and able to provide a safe airport operating environment in accordance with any limitation the Administrator finds necessary to ensure safety in air transportation. The applicant must include in the ACM any additional provision that the Administrator finds necessary to ensure the safety of air transportation.
2.8.3.1 Surrendering an AOC or Modifying the Class Certificate. Under Part 139, an airport operator can surrender the AOC or apply to the FAA to modify the Class certificate. The FAA is the only agency authorized to modify the Class Certificate of an airport. Both certificate actions have implications that must be carefully considered. Under Airport Improvement Program (AIP) grant assurances, an airport receiving Federal funds must provide reasonable, not unjustly discriminatory, access to the airport. The Class of AOC held by an airport can affect access to an airport because air carrier operators can conduct operations only at airports with the appropriate level of AOC. There could be grant assurance compliance implications for an airport operator requesting to drop down in AOC class or surrender its AOC, especially if it could restrict current air carrier operations. Consult with the Regional Airport Compliance Officer before approving such requests for certificate action.
1. If an airport operator wishes to voluntarily surrender its AOC, ACSIs should ensure this is initiated in the form of an official notice received on airport letterhead and signed by the certificate holder. The notice must be provided in hardcopy format; an electronic copy for record keeping purposes only is suggested.
2.10.1 Assigning an AOC Class. › 2.10.1.1 In addition to an ACM, the operator applying for the AOC (or…
2. The AOC should also accompany this surrender notice.
3. Any request for surrendering an AOC or requesting modification to a Class Certificate must be coordinated with AAS-300.
4. All communications about AOC surrender or requests for AOC Class Certificate change should be made on official letterhead and memorandum rather than via email.
5. If there is a modification to the Class Certificate, there will be changes required in the airport’s ACM. The ACSI must ensure all changes to the ACM follow the standard ACM revision process outlined in of this Order.
6. Once the revised ACM has been approved for modifications to the Class Certificate, the related information must be updated in CCMIS and the 5010 databases. Notify AAS-300 of the AOC Class change in order to update the Part 139 Airport Certification Status List.
2.8.3.1.1 Changes in AOC Class. The class of an existing AOC can be downgraded without an airport inspection. An upgrade in class may require a full airport inspection.
Note: The FAA is the only agency authorized to modify the Class Certificate of an airport.
2.9 Section 139.105, Inspection Authority.
The applicant for an AOC or the holder of an AOC must allow the Administrator to 2.9.1
2.9.2
2.10
conduct any inspection, including unannounced inspections and tests, to determine compliance with 49 U.S.C. 44706 and the requirements of Part 139. This includes testing personnel for competency and qualification for performing assigned duties.
Once an ACSI receives credentials, the inspector is officially recognized as a representative of the Administrator. If a certificate holder or his/her representative refuses to allow an ACSI to conduct an inspection, interferes with the conduct of an inspection, or otherwise refuses to allow the inspector to conduct his/her official duties, the inspector will discontinue the inspection and immediately notify the Regional 620. The Regional 620 will notify AAS-300. Refusal on the part of an airport certificate holder or his/her representative will result in a violation of Part 139 and legal enforcement action (see Chapter 5).
Section 139.107, Issuance of Certificate.
Assigning an AOC Class. 2.10.1
2.10.1.1 In addition to an ACM, the operator applying for the AOC (or applicant) submits the application for a certificate on FAA Form 5280-1. In Section
C of the application, Operative Data, the applicant indicates which Class of certificate it is seeking. While the applicant’s request is taken into consideration, the FAA determines the Class of AOC for each airport applying for certification. The FAA takes several factors into consideration to determine the appropriate Class for an airport. These items include the—
2.10.3 Administrative Prerequisites for Issuing an AOC. › 2.10.3.2 The following sections of Part 139 are identified as…
Letter of Intent from the air carrier;
Aircraft size, number of passenger seats, and number of operations per
day or within a 3-month period; and
Aircraft Rescue Fire Fighting (ARFF) requirements for the aircraft and
intended operations.
2.10.1.2 The purpose of establishing the separate Classes is to allow the appropriate level of safety regulation to be applied for the type of aircraft operation at the airport and to avoid imposing more stringent requirements than are actually necessary.
Processing the Application for Certificate and Completion of the AOC. 2.10.2
2.10.2.1 Application for Certificate (Form 5280-1). FAA processing of an application begins with the completion of the “FAA USE ONLY” sections of the form, followed by approval of the ACM and an initial inspection that (1) finds the airport to be in full compliance with Part 139 or (2) results in a Compliance Letter with the AOC. The “Remarks” section on the form should note any previous certification, including dates and type of certificate. The contents of the ACM are discussed in AC 150/5210-22, Airport Certification Manual (ACM). Chapter 4 discusses the requirements of the initial inspection, including the provision for issuance of an AOC with Compliance Letter.
Administrative Prerequisites for Issuing an AOC. 2.10.3
2.10.3.1 There are certain sections of Part 139 that are “administrative” in nature and context. These sections must be addressed and documented by the applicant, submitted to the FAA for approval, and subsequently incorporated into the applicant’s FAA-approved ACM.
2.10.3.2 The following sections of Part 139 are identified as “administrative” and must be fully addressed, documented, and approved prior to the issuance of a FAA AOC: 139.103, 139.201, 139.203, 139.301, 139.303, 139.311, 139.319, 139.321, 139.325, 139.327, 139.329, 139.331, 139.337, and 139.339.
2.10.6.1 Inactive Status. › 2.10.6.1.2 An airport certificate holder who no longer receives air…
2.10.3.3 Prior to the issuance of the AOC, Regional 600/620 must verify the applicable administrative sections of Part 139 are reviewed and approved in the applicant’s ACM. This review must be documented in CCMIS; the entry must identify each applicable administrative section as complete and meeting the statutory requirement for Part 139.
Completion of the AOC. 2.10.4
2.10.4.1 The AOC is completed by ensuring the “Name” and “Associated City and State” are consistent with the information on the Airport Master Record (Form 5010-1). The “Effective Date” is the date the airport operator was first granted certification. The location from which the AOC is issued is the city in which the regional office is located. The Associate Administrator for Airports has delegated the authority for signing the AOC to the Regional Airports Division Manager (600). In the absence of the Regional Airports Division Manager, the Acting Manager may sign the AOC if the certificate must be issued immediately.
2.10.4.2 A cover letter is prepared to transmit the AOC to the certificate holder.
2.10.4.3 A copy of a marked-up Airport Master Record, noting the appropriate airport Class and ARFF index (see Paragraph 4.16), is then sent to Airport Engineering Division (AAS-100) to transmit to the National Flight Data Center (NFDC) for action.
Environmental Categorical Exclusions. 2.10.5 Chapter 5 of Order 1050.1, Environmental Impacts: Policies and Procedures identifies actions that may be classified as a categorical exclusion. The issuance of an AOC under Part 139 is included in the list and does not normally require a higher level of NEPA review. However, if issuing an AOC is likely to involve extraordinary circumstances (see Order 1050.1F 5-2. Extraordinary Circumstances) where that action has a potentially significant environmental impact, the proposed action will require further analysis in an environmental assessment and environmental impact statement.
Certificated Airports Without Air Carrier Service. 2.10.6
2.10.6.1 Inactive Status.
2.10.6.1.1 An airport without air carrier service requiring certification under Part 139, but whose operator applies for certification, can be certificated and placed in “Inactive Status.” An AOC will be issued, provided the certificate holders comply with all provisions and requirements of the current Part 139.
2.10.6.1.2 An airport certificate holder who no longer receives air carrier service may request to be placed in “Inactive Status” and simultaneously maintain its
2.11.3 The FAA has the authority to change the AOC Class assigned to an… › 2.11.3.1 An airport operator whose certificate has been placed in…
AOC, provided the certificate holder complies with all provisions and requirements of the current Part 139.
2.10.6.1.3 In each instance, these airports are placed in “Inactive Status” and are subject to surveillance, periodic, and unannounced inspections at the discretion of the Regional Airports Division. The certificate holder remains subject to administrative action resulting from an inspection. Inactive Status is intended to be a voluntary action on the part of the certificate holder; however, it may also be directed by the Regional Division if warranted. AAS-300 staff should be consulted to determine the best course of action if the Region wishes to move the certificate holder to Inactive Status.
2.10.6.1.4 To return to Active Status, the airport must be scheduled to resume air carrier service and will undergo a full airport inspection prior to being deemed Active.
2.10.6.1.5 If the FAA finds that a certificate holder who retains an “Inactive Status” certificate cannot meet the requirements of the certificate and subsequently finds it in non-compliance, the FAA may suspend or revoke the certificate, depending on the severity of the non-compliance.
2.10.6.2 Surrender of Certificate. An airport certificated under Part 139, which does not have air carrier service and is unable to comply with the provisions of the current Part 139, may surrender its certificate to the Administrator with no adverse condition affecting a future certification.
2.11 Section 139.109, Duration of Certificate.
An AOC is valid and effective until the certificate holder surrenders the certificate or 2.11.1 the Administrator suspends or revokes the certificate.
The FAA has the authority to suspend or revoke an AOC if an airport does not meet the 2.11.2 standards and/or requirements of Part 139. The Regional office must coordinate any suspension or revocation of an AOC with AAS-300, as well as with their Regional Counsel’s office.
The FAA has the authority to change the AOC Class assigned to an airport if and when 2.11.3 air carrier service changes at the airport. The Regional office must coordinate any class change with AAS-300.
2.11.3.1 An airport operator whose certificate has been placed in “Inactive Status” must maintain the level of Certificate Class and comply with the applicable provisions of Part 139 and the airport’s approved ACM.
2.13 Section 139.113, Deviations. › 2.13.1 Deviation from any requirement of Subpart D or the approved ACM,…
2.11.3.2 The certificate holder of an airport in “Inactive Status” must notify the Administrator in writing of resumption of scheduled or unscheduled air carrier activity at least 90 days in advance of such activity. A complete inspection must be conducted to remove the airport from “Inactive Status” prior to the resumption of air service at the airport.
2.11.3.3 A new AOC must be issued if an airport undergoes a name change. The new AOC will be issued on the effective date of the name change.
2.12 Section 139.111, Exemptions.
In accordance with 14 CFR Part 11, General Rulemaking Procedures, a certificate 2.12.1 holder may petition for an exemption from any requirement under Part 139.
Exemptions are time-limited and do not exceed 3 years. Each exemption must be 2.12.2 reviewed annually for currency, extension or renewal. This keeps the exemption in a continuous review process, which results in closer monitoring of airport operator actions to terminate/eliminate the need for the exemption.
Petitions for exemptions must meet the criteria outlined in § 139.111(b) as well as 14 2.12.3 CFR Part 11.
An exemption is not a “Modification of Standards.” Order 5300.1, Modifications to 2.12.4 Agency Airport Design, Construction, and Equipment Standards, contains information and guidance for issuing modifications to standards. Paragraph 5, Exemptions (in version F), reads “Exemptions from 14 CFR Part 139 . . . are not covered by this Order.” Therefore, a modification of standards is not issued as a means of achieving compliance with Part 139 requirements. If, however, a modification of standards is issued in the context of Order 5300.1 and it impacts Part 139 requirements, it must be addressed in the approved ACM.
Exemptions for ARFF requirements under § 139.111(b) must be coordinated with AAS- 2.12.5 300.
A current Exemptions List must be kept with the approved ACM. 2.12.6
Note: See Chapter 8 for a description of the exemption process.
2.13 Section 139.113, Deviations.
Deviation from any requirement of Subpart D or the approved ACM, to the extent 2.13.1 required to meet emergency conditions that threaten life or property, is permitted, provided that—
1. The certificate holder notifies the Regional Airports Division Manager of the nature, extent, and duration of the deviation as soon as possible but at least within 14 days of the emergency.
2.15.2 The commission by any owner, operator or other person acting on… › 2.15.2.2 If airport operators revise their ACM to address this…
2. The certificate holder provides the notification in writing when requested.
Example of a Deviation. 2.13.2 ARFF personnel respond to a vehicular accident on an airport access road. The airport is not able to maintain the ARFF index, and a Notice to Airmen (NOTAM) is not issued. This would be a deviation from the regulation and the airport's ACM and could require an explanation in writing if an air carrier complained to the FAA about the reduced ARFF coverage.
2.14 Change of Ownership. When airport ownership is transferred from one organization to another, the AOC does not transfer. The new owner must submit a new AOC application and an updated ACM. Once the FAA approves the ACM, the agency will issue a new AOC. If the airport has been physically inspected within the last 12 months, there is no need to conduct an additional inspection unless there has been a significant change in airport personnel/management or changes in the airport certification program related to the change in ownership. When there are significant changes in airport personnel, it may be appropriate to conduct a surveillance inspection to ensure that new personnel are trained in accordance with the requirements of § 139.303(c).
2.15 Section 139.115, Falsification, Reproduction, or Alteration of Applications, Certificates, Reports, or Records.
Airport certificate holders cannot make or cause to be made any— 2.15.1
1. Fraudulent or intentionally false statement on any application for a certificate or approval under Part 139,
2. Fraudulent or intentionally false entries into any record or report that is required to be made, kept or used to show compliance with any requirement under Part 139, or
3. Reproductions or alterations, for a fraudulent purpose, of any certificate or approval issued under Part 139.
The commission by any owner, operator or other person acting on behalf of a 2.15.2 certificate holder of an act prohibited under this section, is a basis for suspension or revocation of any certificate or approval issued under Part 139 and held by that certificate holder and any other certificate issued under this title and held by the person committing the act.
2.15.2.1 Under this premise, airport operators may consider revising their ACM to add a new § 139.115 (Falsification, reproduction, or alteration of applications, certificates, reports, or records) to ensure that airport personnel are aware of the Part 139 requirement.
2.15.2.2 If airport operators revise their ACM to address this requirement, ACSIs must verify with airport certificate holders if this action was completed as
an amendment to the airport ACM. If there was no ACM amendment, an equivalent method or notification to all persons with record keeping responsibilities is strongly encouraged.
CHAPTER 3. AIRPORT CERTIFICATION MANUAL
3.1 Purpose. This Chapter provides guidance on approving and maintaining the Airport Certification Manual (ACM). This Chapter also identifies the ACM requirements that apply to each of the airport classes. An approved ACM is an extension of the Part 139 regulation and its contents are legally enforceable under Federal law. An ACM should describe how a certificate holder complies with part 139 requirements in a manner acceptable to the Administrator. Airport operators must review AC 150/5210-22 for ACM development guidance.
Chapter 3. Airport Certification Manual › 3.3 Section 139.203, Contents of the Airport Certification Manual.
3.2 Section 139.201, General Requirements. Part 139 requires each certificated airport to be operated according to an ACM. The manual must contain only those items authorized by the Regional Airports Division or AAS-300 and be:
1. Be approved by the Regional Airports Division Manager; Lead ACSI, or ACSI assigned to the airport submitting the ACM.
2. Be submitted in print and in duplicate—with one approved, complete copy retained at the airport and available for inspection and one approved, complete copy retained at the appropriate Regional Airports Division.
Note: An electronic version of the ACM is acceptable provided it meets the criteria illustrated in (1) and (2) above.
3. Be in a format easy to revise and organized in a manner helpful to the preparation, review, and approval processes, with a revision log to track changes.
Note: The date of approval/revision and reviewer’s initials must be displayed on each page of any ACM submitted electronically.
4. Be signed by the certificate holder to acknowledge its responsibility to operate the airport in compliance with the approved ACM.
5. Be kept current at all times.
6. Include any modification to standards approval letters.
7. Be distributed to those personnel who are responsible for its implementation and be distributable in applicable portions rather than as a full document (i.e. airport police, air carrier agents, FBOs, etc.). The airport must continue to ensure the most current version is provided to recipients, regardless of whether the distribution is full ACM or by section.
3.3 Section 139.203, Contents of the Airport Certification Manual. The ACM must address all parts of Part 139 that apply to the airport. It must be comprehensive and speak directly to the Part 139 requirements, but it is not expected to be an all-inclusive list of instructions. Certificate holders should be reminded that all
3.4 Section 139.205, Amendment of the Airport Certification Manual. › 3.4.1 Authority to Amend the ACM.
text in an approved ACM is enforceable under the Federal Aviation Regulations. The approved ACM should be clear in its instructions, but without unnecessary content.
The ACM must— 3.3.1
1. Contain a description of operating procedures, facilities and equipment, and responsibility assignments as well as any other information needed by the personnel who operate the airport.
2. Contain the required elements specified in § 139.203(b) for each certificate class.
3. Reflect the current conditions, operations, and procedures in effect at the airport.
4. Display the date of initial approval or the date of the latest revision on each page.
5. Include a current revision log.
6. Where non-standard procedures and/or Modifications of Standards are in effect, include documentation that supports compliance to a comparable level of safety equal to that described in FAA ACs.
As discussed in Paragraph 2.15 of this Order, § 139.115 addresses falsification, 3.3.2 reproduction, or alteration of applications, certificates, reports, or records. Certificate holders are strongly encouraged to add verbiage providing notice to those personnel responsible for executing portions of the approved ACM about their responsibility under this section of Part 139. It is important to clearly articulate that any airport person, acting on behalf of a certificate holder, is legally liable under the provisions of this section while performing duties within the scope of their responsibilities on the airport.
ACM Transmittal Letter 3.3.3 The initial ACM and revisions/amendments submitted for approval by the certificate holder must be returned to the certificate holder by transmittal letter in hardcopy or electronic submission. The transmittal letter must refer to the approved ACM revisions and amendments or it must state why they were not approved and identify what further action is necessary to meet Part 139 requirements for approval.
3.4 Section 139.205, Amendment of the Airport Certification Manual.
Authority to Amend the ACM. 3.4.1 Under § 139.3, the authority of the Administrator to issue, deny, and revoke AOCs is delegated to the Associate Administrator for Airports, the Director of Airport Safety and Standards, and Regional Airports Division Managers. This authority permits Regional Airports Division Managers to amend any ACM upon application by the certificate holder or on their own initiative if safety in air transportation requires the amendment.
3.4.3 Amendment Initiated by the Certificate Holder. › 3.4.3.2 If the Regional Division Manager denies an application for…
Amendment Initiated by the FAA. 3.4.2
3.4.2.1 When the Regional Airports Division Manager initiates an amendment to the ACM, the Regional office informs the certificate holder in writing with a Notice to Amend. This notice specifies a reasonable period of not less than 7 days within which the certificate holder may submit written information, arguments, and views on the proposed amendment. Send all Notices to Amend by regular and certified mail to establish a record of notice to the certificate holder.
3.4.2.2 The Regional Airports Division Manager will consider all relevant material when making a decision about the amendment and notify the certificate holder within 30 days of the decision to amend or to rescind the Notice to Amend.
3.4.2.3 If the Regional Airports Division Manager decides to implement the amendment, the amendment will go into effect not less than 30 days after the certificate holder is notified of the decision.
3.4.2.3.1 A certificate holder who does not agree with the decision to amend can petition the Associate Administrator for Airports to reconsider the decision. If the decision is petitioned, implementation of the amendment is stayed pending a decision by the Associate Administrator.
3.4.2.3.2 If the FAA decides there is an emergency requiring immediate action with respect to safety, the amendment may be issued without stay, along with a statement of the reasons for the finding in the Notice to Amend.
Amendment Initiated by the Certificate Holder. 3.4.3
3.4.3.1 A certificate holder must submit a proposed ACM amendment in writing to the Regional Airports Division Manager, or designated representative, at least 30 days before the proposed effective date of the amendment, unless the Regional Airports Division Manager permits a shorter filing period.
3.4.3.2 If the Regional Division Manager denies an application for amendment of the ACM, a certificate holder may petition the Associate Administrator for Airports to reconsider the denial.
This page intentionally left blank.
4.2.3 Surveillance Inspection. › 4.2.3.2 Reasons for conducting a surveillance inspection include…
CHAPTER 4. INSPECTION PROCESS
4.1 Purpose. This Chapter provides guidance on conducting inspections of airport operations to verify compliance with Part 139.
4.2 Types of Inspections. There are three types of inspections: Initial, Periodic, and Surveillance.
Initial Inspection. 4.2.1
4.2.1.1 An Initial inspection is required for any airport not currently certificated under Part 139. This is the first inspection conducted by an Airport Certification Safety Inspector (ACSI) before the FAA issues or reissues an Airport Operating Certificate (AOC).
4.2.1.2 An initial inspection may also be required for a transfer of ownership at the airport, which results in a new AOC, unless a full airport inspection was completed within the last 12 consecutive calendar months.
4.2.1.3 The ACSI must prepare a record and report of the initial inspection to be retained in program files as part of the certification process.
Periodic Inspection. 4.2.2
4.2.2.1 Conducted on an agreed-upon schedule, the Periodic inspection helps ensure the airport is safe and the certificate holder is operating the airport in compliance with Part 139 requirements, as well as in accordance with procedures and practices described in the approved ACM.
4.2.2.2 The ACSI must prepare a full record and report of the inspection to be retained in the program files.
Surveillance Inspection. 4.2.3
4.2.3.1 Surveillance inspections are announced or unannounced inspections conducted in addition to the periodic inspections. They can be held at any time.
4.2.3.2 Reasons for conducting a surveillance inspection include following up on a periodic inspection non-compliance finding; monitoring airfield safety during construction activity; validating continued compliance with the airport’s approved ACM or Part 139 standards; providing additional safety oversight at larger, busier airports; reviewing winter operations; confirming a change in ARFF capability/implementation of a new ARFF
4.4.1 Periodic Inspections. › 4.4.1.2 Regional Airports Divisions must consider all applicable…
department; responding to information about enhanced risk (including changes in management, ARFF equipment, or air carrier service). The surveillance inspection can be directed toward a specific requirement and does not need to be all-inclusive.
4.2.3.3 The ACSI must prepare a record and report of the inspection to be retained in program files.
4.3 Inactive Status. Airports having no air carrier service but that retain their AOC may be placed in Inactive Status. These airports are subject to both periodic and surveillance inspections as determined by the Regional Airports Division. They must be inspected prior to any scheduled or unscheduled air carrier operation and must notify the Region in writing 90 days in advance of a qualifying operation.
Note: Regions must coordinate with AAS-300 before placing an airport in Inactive Status to ensure an update to the Airport Certification Status List.
4.4 Schedule of Inspections. At the discretion of Regional management, deviations may be made from the inspection cycles in order to shorten the interval between inspections at a particular airport. Any deviation that would extend the inspection cycles beyond those outlined below must be coordinated with AAS-300 prior to implementation.
Periodic Inspections. 4.4.1
4.4.1.1 Regional Airports Divisions will schedule periodic inspections based upon the following criteria:
1. Inspect Class I, II, and III airports with scheduled air carrier service with more than nine passenger seats on a 9-to-15 calendar month cycle, resulting in a regional average of 12 calendar months between inspections.
a. Regions must make every effort to ensure Class I airports are
inspected at least once every 12 calendar months.
2. Inspect Class IV airports that have only unscheduled air carrier service with more than 30 passenger seats on a 12-to-18 calendar month cycle.
3. Inspect certificate holders with no scheduled air carrier service with more than nine passenger seats on a maximum 24-calendar month cycle, unless placed in Inactive Status.
4.4.1.2 Regional Airports Divisions must consider all applicable factors when establishing the inspection frequency for an Inactive Status airport. Factors affecting inspection frequency can include:
4.4 Schedule of Inspections. › 4.4.2 Surveillance Inspections.
1. Number of enplanements
2. Number of operations
3. Type and level of activity
4. Administrative and enforcement history
5. Management change/ownership change
6. Runway incursion/excursion history
7. Changes in scheduled service
8. Airport geometry
9. Construction activity
10. Wildlife activity/wildlife strike history
11. A recently issued AOC
12. Weather/seasonal considerations
13. Rotation of ACSIs
14. Recent program changes, such as Surface Movement Guidance and Control System (SMGCS), Land and Hold Short Operations (LAHSO), driver’s training, and staffing levels
15. Other considerations deemed appropriate by Regional management
Surveillance Inspections. 4.4.2 There is no schedule for Surveillance Inspections, but factors triggering surveillance inspections can include:
1. The need to validate the airport ARFF index or capabilities
2. Unsatisfactory enforcement history (administrative or legal)
3. AOC issuance or upgrade within the previous 24 months
4. Surface incidents/runway incursion/excursion or vehicle/pedestrian deviations (V/PDs)
5. Recent management and/or ownership change
6. Construction project activity
7. Wildlife activity/strike reports
8. Inactive status
9. Program changes or updates (SMGCS, Snow and Ice Control Plan, ARFF, staffing levels)
10. Indications of safety issues at the airport that need to be reviewed
Chapter 4. Inspection Process › 4.5 Preparation for Initial and Periodic Inspections.
4-4
4.5 Preparation for Initial and Periodic Inspections. Initial and periodic inspections require detailed preparation. Regional Airports Divisions may develop a tentative schedule for a periodic inspection that is convenient for both the ACSI and the airport operator. The ACSI should prepare for an initial and all periodic inspections according to the guidelines detailed below.
1. Provide advance written notice to the certificate holder for initial and periodic inspections. See Appendix F. Be considerate of airport schedules and activity, but remember that § 139.105 allows for the authority to perform any inspections or tests to determine compliance at the discretion of the inspector.
2. Confirm the dates as soon as practicable.
3. Coordinate with other offices and staff as appropriate. Consider contacting the following offices:
4. Airports District Office (ADO)
5. Flight Standards District Office (FSDO) or Certificate Management Office (CMO)
6. Technical Operations (Tech Ops)
7. Transportation Security Administration (TSA)
8. Air Traffic Control
9. Runway Safety Program Office
10. Previous ACSI
11. State aviation agencies
12. Review airport information including:
13. ACM and Airport Emergency Plan (AEP)
14. Snow and Ice Control Plan (SICP) (if applicable)
15. SMGCS/Low Visibility Operations (LVO) (if applicable). See FAA SMGCS Order 8900.94, Procedures for establishing a Volunteer Surface Movement Guidance and Control System /Low-Visibility Operations.
16. Previous inspection records and legal enforcement reports for previous 3 years
17. Violation history for previous 3 years
18. Previous investigation reports, to include V/PD reports
19. Airport Master Record (5010-1) and the Airport/Facility Directory
20. Obstruction chart/airport approach survey
21. Accident/incident history
22. Airport compliance history
4.6 Inspection Protocol–General. › 4.6.1 The Airport Certification Program operates under the premise that…
23. Verbal briefing from the program manager on the status of Airport Improvement Program grants or Passenger Facility Charge approvals associated with construction projects ongoing or planned.
24. Airport Layout Plan (ALP)
25. Wildlife incident history and Wildlife Hazard Assessment/Wildlife Hazard Mitigation Plan (WHA/WHMP) status as applicable.
26. Standard Instrument Approach Procedures (SIAP) for each instrument runway.
27. Information about construction projects for safety and compliance with AC 150/5300-13, Airport Design; design standards for the approach categories of runways and other clearances to be maintained.
28. Ensure availability of proper directives, charts, ACs, and appropriate information to conduct the inspection. Recommended items can include:
29. References such as policy letters, Orders, CertAlerts, Engineering Briefs, and National Fire Protection Association (NFPA) standards as needed and appropriate.
30. CCMISNet history
31. Construction Safety Phasing Plans (CSPP)
32. Runway Safety Area (RSA) inventory
33. Modifications to Standards and exemptions
34. Form 5280-4 Checklist
35. Airport diagram and approach plates
36. Wildlife strike history
37. ARFF equipment list
38. Points of contact list (Airport Ops, Tower, TSA, ARFF, etc.)
39. Runway Safety Action Plan
40. SMGCS Plan (as applicable)
41. Obstruction list for the airport; pay particular attention to those obstructions that need to be illuminated or marked at the airport
42. Compliance files to assess the certificate holder’s compliance to any previous corrective actions required for non-compliance
4.6 Inspection Protocol–General.
The Airport Certification Program operates under the premise that the airport certificate 4.6.1 holder acts responsibly to comply with Part 139 through the self-inspection program. The FAA inspection itself is but a snapshot of how the airport’s own self-inspection program is implemented to ensure safety. The ACSI seeks to validate the actions of the certificate holder in its implementation of the self-inspection program. Through best
4.6 Inspection Protocol–General. › 4.6.5 Documenting Findings.
practices and procedures, diligent airport condition reporting, and timely corrective actions for non-compliance to Part 139, the certificate holder shows how the airport meets the regulatory requirement and those requirements specific to the airport’s approved ACM. It is the ACSI’s primary responsibility to ensure that required “systems” are in place and functioning properly at the airport. These systems ensure ARFF is provided and vehicles are maintained; pavement is inspected and maintained; personnel are trained; and the airport complies with all elements of Part 139. As an example of this philosophy, an ACSI would inspect ARFF personal protective gear (PPE) not to ensure that every piece of gear meets NFPA standards (if NFPA standards have been adopted), but to ensure there is a system in place at the airport to purchase the right gear, track the gear, inspect the gear, and maintain the gear in accordance with current standards. This overriding philosophy should apply to all elements of the inspection.
Due to certain conditions on various airports (e.g., high density traffic or inclement 4.6.2 weather), ACSIs should be flexible about when to conduct an inspection. The ACSI should consider inspecting the movement area when traffic conditions best allow. Recent rain or snow may limit the ability to access certain areas of the airport (e.g., runway safety areas). Weather and traffic alone should not inhibit the ability of an ACSI to see every part of the airport needing to be inspected.
Night Inspections. 4.6.3 Initial and periodic certification inspections must include a night inspection of lighting, signage and marking. ACSIs must conduct night inspections during official darkness, i.e. after sunset and before sunrise.
4.6.3.1 In Alaska, a night inspection is acceptable during the time a prominent, unlighted object cannot be seen from a distance of 3 statute miles or the sun is more than 6 degrees below the horizon.
Interviews. 4.6.4 During the inspection, key airport personnel, including the operations director or supervisor, the maintenance supervisor, the ARFF Chief, the wildlife hazard management supervisor or airport wildlife biologist, and local FAA personnel (e.g., Air Traffic Control Manager) should be available. If any of the interviewees have concerns about sharing information freely in the presence of others, the ACSI should consider conducting interviews separately.
Documenting Findings. 4.6.5 The ACSI will use the Airport Certification/Safety Inspection Checklist (Form 5280-4) to document findings during all airport inspections. Discrepancy write-ups need to be clear, concise and be able to stand on their own to an outside reader.
4.7 Phases of the Inspection. › 4.7.2 Administrative Inspection.
4.7 Phases of the Inspection. The inspection consists of eight phases.
In-briefing. 4.7.1 The in-briefing is a meeting with airport management to discuss the inspection agenda, areas of mutual interest, problem areas, previous inspection results and concerns, the airport’s current status, recent Part 139 issues, runway incursion/excursion issues, and any other topics of concern to the airport operator or ACSI. In addition, the ACSI should coordinate with the Air Traffic Control Tower (ATCT), as appropriate, for inspection access to the movement area and with ARFF personnel to conduct the ARFF timed-response drill, as well as other activities such as the discharge of agent on the airport and the inspection of maintenance records.
Administrative Inspection. 4.7.2 For this inspection, the ACSI should:
1. Review the airport’s copy of its approved ACM to ensure it contains the processes and procedures the airport uses to comply with Part 139 and ensure the official copy of the ACM is accurate, current, and implemented properly by those personnel with responsibilities on the airport. Pay particular attention to those items that frequently change in the ACM (e.g., personnel and telephone numbers, navigational aid (NAVAID) information, changes in pavement information after construction, the sign and marking plan, snow and ice control plans, and airport emergency plan contacts).
2. Special attention should be given when conducting the sign and marking plan review. Review to ensure the Precision Object Free Zone (POFZ) requirements are addressed as applicable. AC 150/5340-18 provides the details for POFZ standards. The Regional Airspace Procedures Team (RAPT) and the Regional Engineering teams are also good sources to consult when reviewing the sign plan.
3. Discuss the status of any exemptions to review the certificate holder’s efforts/actions to resolve the need for an exemption.
4. Check the Notices to Airmen (NOTAMs) to verify congruity between the airport’s condition reporting and the information disseminated to users through the Federal NOTAM System (FNS). Examine NOTAM and/or other airport condition reporting logs for 12 consecutive calendar months.
5. Review the Airport Master Record, Airport Facility Directory, and Airport Diagram for changes and update the record, as appropriate, with the airport operator.
6. Examine documentation required under § 139.301. ACSIs should notify the certificate holder that all inspectable records should be made available at one centralized location upon arrival for the inspection. Various entities on the airport (ARFF, Maintenance, Fueling, etc.) that maintain records should ensure their records are delivered to the agreed upon central location for inspection. ACSIs may also prefer to review the training records, curriculum, and training materials at the
4.7 Phases of the Inspection. › 4.7.3 Movement and Safety Area Inspection.
exact location of where the records are maintained (e.g., at the ARFF facility, at the fuel farm, etc.). Viewing the records where they are normally housed may facilitate the ability to speak directly to the personnel responsible for administering those training programs. All records must be inspected before concluding the inspection.
Movement and Safety Area Inspection. 4.7.3 During this phase, the ACSI observes the certificate holder or a designated representative conduct a self-inspection, to include the following:
1. Inspecting runways and taxiways used by air carrier aircraft to ascertain the condition of the pavement, marking, lighting, signs, shoulders, and safety areas.
2. Verifying marking and lighting configurations are consistent with the ACM, approach charts, the Airport Master Record, the approved Sign and Marking Plan, and current standards.
3. At each runway approach, checking the approach slope with an acceptable handheld instrument and the runway alignment with a compass or global positioning system (GPS). If there is a question about the reported slope or if the ACSI does not have access to any measuring equipment, the ACSI should recommend the airport conduct an official survey to validate the slope and alignment.
4. The ACSI should compare results with the current obstruction chart and Airport Master Record, as well as the most recent approach survey.
5. If construction activity is in progress, checking for adherence to the FAA-approved construction safety phasing plan (CSPP) and safety compliance plan document (SPCD). The ACSI should identify any potentially hazardous condition to runway/taxiway safety posed by excavations, trenches, or stockpiled material. Verify there is adequate lighting and marking of the area, as well as verify correct marking and lighting of any temporary thresholds. It is important for the ACSI to validate the placement of construction equipment away from the movement areas as applicable, keeping in mind areas such as the RSA or taxiway object free area (TOFA).
6. Observing ground vehicle operations for things such as limited access to movement and safety areas by those vehicles required for airport operations and appropriate and correct procedures/communication, adherence to pilot/controller phraseology, and driver understanding of Air Traffic Control conventions. Vehicles must be properly marked and adhere to the approved access routes assigned in the CSPP.
7. Verifying the appropriate NOTAMs have been issued and air carriers have been notified with regard to the construction activity.
8. Inspecting for public protection (inadvertent entry and jet/propeller blast protection). If fencing is installed to meet the requirements of § 139.355, the self-inspection should ensure the fencing is properly maintained.
9. Observing for the presence of wildlife or attractants that present potential hazards. This includes disposal practices for dead or captured animals, how self-inspection
4.7 Phases of the Inspection. › 4.7.4 ARFF Inspections.
procedures address the finding of dead birds or other wildlife, and how personnel are monitored during construction activity for disposal of waste that might attract wildlife.
10. Verifying traffic and wind indicators, to include supplemental wind cones; meeting current standards and appearing visible by pilots in aircraft on final approach for condition; and if used at night, verifying adequate lighting of the wind cones. Wind cones should be inspected during both the day and night inspections.
ARFF Inspections. 4.7.4 During this phase, the ACSI:
1. Checks the index for the critical aircraft and schedule of operations.
2. Checks for appropriate firefighting equipment to meet index and agents. Validates processes/systems in place at the airport for maintenance of ARFF equipment.
3. Checks to ensure the certificate holder has procedures in place for conducting a refractometer or conductivity test. The ACSI may require the ARFF personnel to perform this test during inspection.
4. Checks to ensure the foam production system testing has been conducted as required by the manufacturer specifications.
5. Checks for the certificate holder’s notification procedures to address reduction in ARFF capability, as well as their ability to recall ARFF personnel to increase capability.
6. Checks vehicle and equipment readiness, including the North American Emergency Response the Guidebook accessibility. ARFF personnel are required to have access to the manual; it does not have to be in the truck or on their person, and it may be in electronic format.
7. Checks ARFF emergency access roads to ensure they are accessible.
8. Conducts the timed-response drill. The ACSI cannot close out the inspection until the ARFF response test can be met. This includes establishing special procedures and then testing these procedures to ensure successful time completion. An example of these special procedures could be having the ARFF equipment and personnel pre-positioned at a designated location on the airport during air carrier operations.
9. Ensures a program is in place for ARFF personnel to check the serviceability, care, and maintenance of personnel proximity suits/structural protective gear and selfcontained breathing apparatus (SCBA). Documentation of these inspections should be available for the ACSI to review.
10. Checks ARFF personnel for knowledge of the 11 ARFF areas contained in § 139.319. This can be accomplished in a variety of ways, such as conducting oral quizzes, written test questions, performance-based scenarios, or other methods deemed appropriate by the ACSI.
4.7.5 Fuel Inspections. › 4.7.5.1 During this phase, the ACSI:
11. Checks ARFF personnel training records for accuracy and completeness. Training records should detail the elements of the ARFF training syllabus currently in use. The ACSI must inspect all ARFF training records.
12. Checks to ensure at least one individual per shift on duty during air carrier operations has the basic emergency medical services training. If the ACM specifies the medical response will originate from off the airport, the ACSI must verify the responsible personnel are identified within the ACM and then validate their training documentation. Documentation may include the training certificate, training record, or other official curriculum verification.
13. Verifies that live fire training was conducted at facilities meeting the specifications found in AC 150/5220-17.
Fuel Inspections. 4.7.5
4.7.5.1 During this phase, the ACSI:
1. Checks the certificate holder’s standards for protecting against fire and explosions in storing, dispensing, and otherwise handling of fuel on the airport (or adopted fire code). These must address facilities, procedures, and personnel training according to the seven items listed in § 139.321(b).
2. Checks agents who handle fuel and fuel storage material on the airport in accordance with the applicable fire code at the airport (NFPA 407 or other code as adopted). Inspects a random sampling of vehicles and hydrant carts, or at the ACSI’s discretion, inspects all vehicles and hydrant carts in order to determine compliance.
3. Checks the safety and operations of areas designated for fuel storage material in accordance with applicable fire codes at the airport (NFPA 407 or other code as adopted).
Note: Fuel storage facilities off airport property and outside of the airport operating area are not inspected.
4. Checks the certificate holder’s inspection records of fueling agents on the airport for timeliness, accuracy, and completeness. Checks that the inspections are completed, at a minimum, every 3 consecutive calendar months.
5. Checks supervisory and other personnel training per § 139.321. See AC 150/5230-4, Addendum, for a training course list.
6. When there are fueling operations in progress during the dates of the inspection, observes the fueling of air carrier aircraft in airport ramp areas to ensure proper safety precautions are in place, such as emergency evacuation capability; fire extinguishers; access to the emergency shutoff; and hose protection, as defined in the applicable fire code and the approved ACM.
4.7 Phases of the Inspection. › 4.7.6 Wildlife Hazard Management Inspection.
4.7.5.2 The ACSI should not perform the actual hands-on, physical inspection of any of the fuel trucks, carts, or fuel farms. The ACSI should ensure a designated certificate holder’s fuel representative accompanies the ACSI on the inspection. The ACSI should have the airport personnel demonstrate their knowledge of the fire codes and the inspection process by observing the fueling representative conducting the inspection(s). The ACSI can question airport personnel during the process and ask them to provide a practical demonstration to test knowledge. All demonstrations must be accomplished by the qualified airport certificate holder, fueling agent, or designated representative. The ACSI should not personally adjust, push, pull, or in any way activate any part of the fuel system in conjunction with the inspection. The ACSI’s job is to validate the certificate holder’s self-inspection actions when inspecting the fuel trucks, carts, or fuel farms.
Wildlife Hazard Management Inspection. 4.7.6 During this phase, the ACSI:
1. Observes signs of wildlife during the physical inspection of the airport selfinspection.
2. Asks questions about the presence of wildlife when visiting field offices and the ATCT.
3. Observes habitats and activities conducive to attracting wildlife.
4. Checks self-inspection records for data about wildlife observations by airport personnel and any applicable wildlife tracking logs.
5. If a Wildlife Hazard Assessment (WHA) has been conducted, determines if the airport is required to develop a Wildlife Hazard Management Plan (WHMP). An assessment does not always result in the need for a plan, but if a plan is required, the ACI must determine if that plan has been implemented.
6. Checks to ensure a review of the WHMP has been completed and documented every 12 consecutive calendar months or as needed by triggering events.
7. Checks that staff training is in compliance with the WHMP.
8. Checks airport procedures for alerting users of wildlife activities.
9. Ensures all applicable local, state, and Federal permits have been obtained and are available for inspection. The AAS-300 Wildlife Biologists can be contacted to assist in determining the required permits and what to look for when reviewing permits.
10. Inspects sections of the wildlife fencing for proper maintenance and signs of animal intrusions. Checks gates for close spacing to prevent animal intrusions. If there is a reported deer problem, it may be appropriate to inspect the entire perimeter fence if access is feasible. Checks the certificate holder’s procedures/self-inspection records for inspecting the wildlife fence.
4.7.9 Post-Inspection Out-briefing. › 4.7.9.1 During this final phase, the ACSI:
4-12
11. If the airport employs a wildlife biologist, meet and discuss all aspects of the wildlife management program on the airport with this individual.
Night Inspection. 4.7.7 During this phase, the ACSI:
1. Checks runway and taxiway lights on all air carrier runways/taxiways for alignment, spacing, and optical performance. If Pilot Controlled Lights are installed, requests changes in runway step lighting to evaluate intensity of lighting at each step.
2. Checks obstruction lighting listed in the approved ACM for operability in accordance with § 139.311.
3. Checks shielding of lighting on ramps and aprons.
4. Checks marking and sign visibility at night. This must include checking the glass beads for adequate reflectivity.
5. Checks the visibility of wind and traffic indicators for night operations.
6. Where appropriate, checks marking and lighting of unusable portions of the airport.
7. Checks lighting and marking in construction areas is in accordance with CSPP and determines adequate visibility of hazards.
Air Traffic Control Tower Interview. 4.7.8 There are no Part 139 regulatory inspection requirements associated with the Air Traffic Control Facility; however, ACSIs are encouraged to meet with the Air Traffic Control Manager. Such a meeting allows the ACSI to ask Air Traffic Control personnel if they want to discuss potential issues or concerns with the airport certificate holder.
Post-Inspection Out-briefing. 4.7.9
4.7.9.1 During this final phase, the ACSI:
1. Consolidates notes from the approved ACM review, the phases of inspection (Paragraphs 4.7.1-4.7.7 above), and the Airport Certification/Safety Inspection Checklist (Form 5280-4).
2. Presents specific non-compliance and safety concerns identified during the inspection. The ACSI gives the out-brief to airport management staff and any airport personnel with duties outlined in the ACM.
3. Throughout the discussion, assesses as best as possible the compliance attitude of the certificate holder.
4. If non-compliance is found in any area of the airport and/or Part 139 requirements, determines the level of enforcement action necessary in order to bring the certificate holder back into compliance. If warranted, takes the appropriate administrative action such as issuing a Compliance Letter. This letter can be issued at the time of the out-
4.9 Section 139.301, Records. › 4.9.1 The certificate holder must furnish, upon request by the…
4-13
brief, or upon return to the Regional Airports Division office after consulting with Regional Management.
5. If a Compliance Letter is issued, establishes a date by which the noncompliance must be corrected. In the case of an unsafe condition that warrants immediate action to mitigate an unacceptable risk, takes immediate action. Actions will include bringing the identified risk to the attention of the certificate holder and discussing with Regional and Headquarters management the appropriate safety response to the immediate risk.
6. If no issues of non-compliance are identified, issues an Inspection Close-out Letter either on site or upon return to their Regional office.
4.7.9.2 Recommendations cannot be provided for areas of Part 139 noncompliance found during the inspection. While non-binding, ASCI recommendations are still considered useful tools to ensure a full and accurate picture is provided on the overall level of safety at the airport. The ACSI may observe safety issues that are outside of the Part 139 purview but could create potential hazards that, if not addressed, might result in regulatory violations in the future. When making a recommendation, the ASCI should limit their advice to identifying the concern or risk as opposed to solving the problem for the sponsor.
4.8 Inspection Protocol–Specific Guidance.
The following sections provide further details about the conduct of an airport 4.8.1 certification safety inspection. The ACSI should compare conditions on the airport to applicable current regulatory standards when non-compliance is found. The approved ACM will provide additional supplemental guidance; however, FAA regulatory standards and requirements take precedence over ACM guidance.
Paragraphs 4.9 through 4.30 discuss standards and aspects of the program to consider 4.8.2 when conducting an inspection. Part 139 speaks in detail to all actions and requirements the certificate holder must adhere to in order to maintain its certificate. Part 139, subpart D, Operations, must be reviewed and consulted prior to and throughout the inspection process when determining whether the certificate holder is complying with each requirement identified. Each of the sections below contains a brief overview of the certificate holder’s responsibilities; however, the language in Part 139 must be referenced and verified when discerning the certificate holder’s compliance with a specific requirement.
4.9 Section 139.301, Records.
The certificate holder must furnish, upon request by the Administrator, all records 4.9.1 required to be maintained under this section.
4.9 Section 139.301, Records. › 4.9.3 An increasing number of certificate holders are using computer…
The ACSI must confirm the certificate holder is adequately maintaining all records 4.9.2 required under Part 139, including the following:
1. Records for airport personnel training, as required under § 139.303 and §139.327, and the records for emergency personnel training (ARFF and medical service), as required under § 139.319. These records must be maintained for 24 consecutive calendar months.
2. Records for fueling agent training must be maintained for 24 consecutive calendar months
3. Records of inspections of fueling agent trucks and fuel storage areas must be maintained for 12 consecutive calendar months.
4. Records for self-inspections, as required in § 139.327, must be maintained for 12 consecutive calendar months.
5. Records for training ground vehicle operators and personnel with access to the movement area and safety areas, as required in §139.329, must be maintained for 24 consecutive calendar months. The records must reflect personnel having been trained within 12 consecutive calendar months of their previous training.
6. Records for an accident or incident occurring on the movement and/or safety areas involving air carrier aircraft and/or ground vehicles, as required in § 139.329, must be maintained for 12 consecutive calendar months.
7. Records of airport conditions, as required in § 139.339, must be maintained for 12 consecutive calendar months. NOTAMs should be reviewed and compared with records of self-inspections. The ACSI must verify that appropriate and timely NOTAMs were issued for any discrepancies requiring a NOTAM.
8. Other records determined to be necessary by the Administrator, e.g., work orders for discrepancies identified during self-inspections.
An increasing number of certificate holders are using computer databases to track 4.9.3 employee training records. In most cases, the employees are not required to physically sign the training record itself; however, the record must provide the name of the individual in attendance, the date, and the description of the training conducted. While the ACSI may encourage the airport operator to use sign-in sheets for training, the lack of such sheets does not invalidate the training. If there is any doubt about the employee having taken the training, the ACSI may query the employee about whether he/she received the training and may choose to test the employee’s knowledge of the subject area in question.
Note: These specific criteria apply to all recordkeeping requirements established under Part 139.
4.10.4 The ACSI determines if the certificate holder is providing… › 4.10.4.3 Determination of sufficiency and qualifications must be based…
4.10 Section 139.303, Personnel.
The certificate holder must provide sufficient and qualified personnel to comply with 4.10.1 the requirements of its approved ACM as well as the requirements under this part. It must equip personnel with sufficient resources needed to comply with the requirements of this part and train all persons who access movement areas and safety areas and perform duties in compliance with the requirements of the ACM and the requirements of this part.
The certificate holder must also make a record of all training completed after June 9, 4.10.2 2004, by each individual in compliance with § 139.303 that includes, at a minimum, a description and date of training received. Such records must be maintained for 24 consecutive calendar months after completion of training.
The certificate holder may use an independent organization, or designee, to comply with 4.10.3 the requirements of its ACM and the requirements of this part only if such an arrangement is authorized by the Administrator.
The ACSI determines if the certificate holder is providing sufficient and qualified 4.10.4 personnel to comply with the requirements of its approved ACM and the requirements listed in Part 139.
4.10.4.1 FAA Memorandum dated 25 August 2014 states, in part: “It is not reasonable to assume that the FAA meant ‘no personnel’ would be sufficient to meet the requirements of Part 139. Although we can conclude that Part 139.303(a) requires at least one airport employee or designee is onsite during air carrier operations, the number of individuals that would be sufficient depends on the specific need of each airport after considering its size and layout, as well as the volume and complexity of operations.”
4.10.4.2 The ACSI cannot specify the exact number of employees the certificate holder must have but can identify whether the number of employees is sufficient by observing how many are required to maintain and operate the airport at the minimum safety standards in Part 139. The ACSI must be able to identify at least one qualified person who is onsite during air carrier operations to carry out each applicable section of the ACM.
4.10.4.3 Determination of sufficiency and qualifications must be based on conditions found during the inspection, such as—
Multiple inspections with a high number or non-compliance areas,
An unusually high number of non-compliance in a single self-
inspection,
Observation of the employees performing their duties, and
4.11.2 The ACSI’s responsibilities entail advising the certificate… › 4.11.2.2 Marginal Condition Rating.
Staffing rosters and position descriptions.
4.10.4.4 In addition, ACSIs can administer oral or written tests or request practical demonstrations of skills to determine whether there are sufficient and qualified personnel. Such methods are only one tool, and are not an allinclusive means of making a determination. Tests or demonstrations must be appropriate for the airport class, index, and conditions of that specific airport.
4.10.4.5 It is necessary to distinguish between the personnel requirements because there might be a “sufficient” number of personnel, but not enough “qualified” personnel due to deficiencies in training. If the work performed on the airport is completed, but done improperly, this might indicate a need for better training. The certificate holder is required to develop a training program that provides training for the areas subject to Part 139.
4.11 Section 139.305, Paved Areas.
The certificate holder must maintain and promptly repair the pavement of each runway, 4.11.1 taxiway, loading ramp, and parking area on the airport that is available for air carrier use as described in § 139.305(a)(1) - (6) for specifics.
The ACSI’s responsibilities entail advising the certificate holder of pavement conditions 4.11.2 involving possible pavement deterioration (e.g., evidence of cracking, ponding, spalling, or settling) identified during the inspection. ACSIs should advise the certificate holder that corrective action must be taken if such evidence of deterioration exists. Following the inspection, the ACSI should advise the appropriate ADO of the pavement condition for situational awareness. If the pavement condition is severe, advise the ADO or program office immediately.
4.11.2.1 ACSIs may consider using AC 150/5320-17, Airfield Pavement Surface Evaluation and Rating Manuals (PASER Manuals), to determine pavement conditions and to present conditions in a standardized manner. Pavement at an airport is most likely subjected to a more formal pavement analysis by a pavements engineer, and the airport may already have a formal pavement management system in place. ACSIs can use this system to assess pavement distress and assign a simple rating (Excellent to Failed), which can appear in the Airport Master Record. Such ratings, however, are secondary to determinations made through formal pavement condition index (PCI) ratings.
4.11.2.2 Marginal Condition Rating. When evaluating pavement condition, the ACSI should keep in mind cracks and/or surface variations could create a Marginal condition rating,
4.11.2 The ACSI’s responsibilities entail advising the certificate… › 4.11.2.4 Section 139.305(a)(2).
which produces lose aggregate or other contaminants. Besides resulting in foreign object debris, this condition could impair directional control of air carrier aircraft and must be treated as non-compliant. It is also important to note holes and other surface aberrations in the pavement must be evaluated against criteria in § 139.305(a) (2) and (3) since a condition that passes criteria listed in (2), might fail the criteria listed in (3).
4.11.2.3 Significant Safety Hazard Determination. If the ACSI determines that a portion of the paved area presents a “significant safety hazard” based on AC 150/5320-17 and intends to assign a preliminary PASER rating of 1-Failed, the ACSI must take the following actions:
1. Immediately notify the senior airport official on duty or the airport operator of the preliminary determination of a “significant safety hazard”. The ACSI must document the name of the person notified and the date and time of notification.
2. Contact his/her Regional Management as soon as practicable about the determination and provide the details of the results of the pavement inspection. The ACSI should consider transmitting digital photographs of the paved area in question to management during the course of this coordination.
3. The ACSI will request the certificate holder implement immediate corrective measures that will mitigate the hazard and minimize the impact to air carrier operations until a more permanent solution can be put in place. This could entail closing the area to air carrier operations.
4. Based on the complexity of the airport, the ACSI will request the certificate holder coordinate with an airport engineering representative to formally assess and address the condition of the paved area. The ACSI will also coordinate with the FAA program manager in the Regional office or ADO. The ACSI should also inquire about existing projects, plans, and programming for future projects for pavement maintenance, overlays, and full reconstruction.
4.11.2.4 Section 139.305(a)(2). A hole no larger than 5 inches in diameter, less than 3 inches deep, and with a sideslope of less than 45 degrees is not a discrepancy as a hole, but it might be considered a crack that affects the directional control of an air carrier aircraft. See also § 139.305(a)(3). If a hole is 3 inches or less in depth, it not a discrepancy under § 139.305(a)(2). If it exceeds 3 inches in depth, other tests need to be considered:
1. If the entire surface area of the hole can be covered by a 5 inch diameter circle, it is not a deficiency under § 139.305(a)(2). If the hole
4.13 Section 139.309, Safety Areas. › 4.13.1 The certificate holder is responsible for properly maintaining…
cannot be covered by a 5 inch diameter circle and the sideslope at any point is 45 degrees or greater, it is a deficiency.
2. If the hole cannot be covered by a 5 inch diameter circle but the sideslope at any point in the hole is less than 45 degrees, it is not a discrepancy under §139.305(a)(2). It might be a discrepancy under § 139.305(a)(3) if it is determined the surface variation could impair the directional control of an air carrier aircraft.
4.11.2.5 Section 139.305(a)(3). Longitudinal cracks are more likely to affect directional control of an air carrier aircraft than transverse cracks.
4.11.2.6 Section 139.305(a)(4). Loose aggregate, foreign objects, rubber deposits, snow and ice clumps, and other contaminants that could be ingested into aircraft engines must be removed from paved areas promptly and completely.
4.11.2.7 Section 139.305(a)(5). Chemical solvents used on pavement must be removed from paved areas promptly and completely.
4.11.2.8 Section 139.305(a)(6). Pavement must be sufficiently drained and free from depressions.
4.12 Section 139.307, Unpaved Areas.
The certificate holder must maintain and promptly repair the surface of each gravel, 4.12.1 turf, or other unpaved runway, taxiway, or loading ramp and parking area on the airport that is available for air carrier use.
The ACSI must determine if all unpaved areas available for air carrier use, including 4.12.2 loading ramps and parking areas, are maintained properly. Unpaved surfaces may be comprised of stone or gravel, and include unpaved runways and taxiways. The ACSI should advise the certificate holder of any non-compliance and require corrective action.
4.13 Section 139.309, Safety Areas.
The certificate holder is responsible for properly maintaining the condition of the safety 4.13.1 areas. The dimensions of the safety areas must be entered in the approved ACM, along with the design standards applicable to the associated runway. If safety areas do not meet current airport design standards, the ACSI should address this issue with the certificate holder and determine their actions to come into compliance with the current airport design standards.
4.13.6 Safety areas should support a vehicle or ARFF equipment during… › 4.13.6.1 Engineered Material Arresting System (EMAS).
Even if the full length/width of the design standard for a safety area cannot be achieved, 4.13.2 it might be practicable to extend the safety area by a small incremental land acquisition. It may also require minor earthwork or the relocation of a ditch/culvert. Gaining as much safety area as possible is important for providing the maximum achievable level of safety.
Major pavement reconstruction projects, which are part of an overall plan to extend the 4.13.3 useful life of the runway/taxiway, and similar major pavement rehabilitation efforts should be considered reconstruction and thus trigger the safety area requirements of § 139.309(a). The addition of a slurry seal or sealcoat, grooving, and pavement overlay designed only to protect the structural integrity of the existing pavement as a means of achieving its originally anticipated strength is not considered reconstruction under this provision. Significant expansion would include projects clearly designed to accept a different critical aircraft or to provide for increased payload or range for the existing critical aircraft using that pavement. As a guideline, extending a runway 500 feet or more is considered significant for the purpose of this provision.
The ACSI must have the ability to accurately check safety area dimensions that do not 4.13.4 appear to be correct. The ACSI should note any significant discrepancy in the measurements of the safety area and any discrepancy in the maintenance of the safety area. It is often helpful to review any airport surveys or airport engineering surveys that have been conducted and may include the safety area dimensions.
The ACSI may have the vehicle operator drive in portions of the safety areas to evaluate 4.13.5 surface conditions. Additionally, the ACSI should consider physically walking portions of the safety area if time and operations permit. This will facilitate further verification of potential discrepancies. Unusual airport conditions caused by seasonal variations, such as snow, mud, and water, are evaluated on a case-by-case basis.
Safety areas should support a vehicle or ARFF equipment during dry conditions and the 4.13.6 inadvertent excursion of an aircraft without causing major damage. Safety areas must be cleared and graded and have no potentially hazardous humps, ruts, depressions, or other surface variations. They must be drained by grading or by storm sewers to prevent water accumulation. When safety areas are affected by weather, and vehicle traffic in the area is not recommended, the ACSI should consider inspecting the area on foot to check areas of interest. The ACSI must ensure communication with ATCT is initiated as required.
4.13.6.1 Engineered Material Arresting System (EMAS). Where sufficient land cannot be acquired to meet RSA design standards, EMAS may be installed. The ACSI should ensure the certificate holder has adequate methods for inspecting EMAS to detect deterioration, inadvertent entry, and controlled entry. The certificate holder should also conduct training for airport personnel with access to the RSA to prevent vehicles and pedestrians from entering the EMAS. Any EMAS training required for airport personnel should take place as early as the initial
4.13.6 Safety areas should support a vehicle or ARFF equipment during… › 4.13.6.4 Waiver.
construction of the EMAS if possible. EMAS are not designed to support use by maintenance vehicles. EMAS requires a maintenance plan approved by the FAA. ACSIs should verify a maintenance plan is in place and appropriate records are available to ensure all required inspections and maintenance have been conducted by the airport operator and/or EMAS provider. ACSIs should take into consideration evaluating useful life of first-generation EMAS beds, including replacing and checking for NOTAM language when the bed is no longer reliable.
4.13.6.2 Safety Area Conditions.
4.13.6.2.1 Protection of the RSA and personnel in the RSA is the airport operator’s responsibility. Any event that occurs in the RSA lies within the certificate holder’s purview.
4.13.6.2.2 Unless fixed by function, no object is permitted within the RSA. Objects fixed by function and located in the RSA must be on frangible mounts and be no higher than 3 inches above grade. If the ACSI determines that an FAA NAVAID is not properly mounted, the ACSI should identify any grading discrepancy on the inspection report and note that the Regional Technical Operations Office will be notified of the condition. The ACSI should also advise the certificate holder to work with the Technical Operations Office to correct the discrepancy.
4.13.6.3 Authorized RSA Activity. The airport operator, in consultation with the local ATCT and FAA Technical Operations, should consider air traffic operations, weather, and other conditions before allowing maintenance personnel or equipment into the RSA. A runway closure should be utilized prior to allowing personnel or equipment in the RSA. However, if it becomes necessary to gain access to the RSA without discontinuing air carrier/aircraft operations, activities may occur based on the conditions listed in a signed LOA (see AC 150/5210-20A, Ground Vehicle Operations to include Taxiing or Towing an Aircraft on Airports).
4.13.6.3.1 Safety Area Procedures. The LOA defines the responsibilities and procedures parties entering into the agreement must consider for accessing, operating, and exiting the airport’s RSA during air carrier or aircraft operations. Authorized RSA activity access should not be used for long-term access such as construction projects. In addition, personnel must maintain two-way radio communications with ATCT.
4.13.6.4 Waiver. In a situation where a high-mass object currently penetrates any of the areas previously defined above, a waiver may be requested by the airport
operator provided there are proper safety considerations for vehicles and personnel to penetrate these areas during air carrier operations. High-mass objects include those substantial enough to cause considerable damage to aircraft. Examples include NAVAIDs mounted on large heavy structures and equipment shelters constructed of concrete.
4.14 Section 139.311, Markings, Signs, and Lighting. › 4.14.2 The ACSI must verify the marking, signs, and lighting systems…
4.13.6.4.1 The Regional Airports 620 Manager will approve these waivers on a caseby-case basis. The Regional 620 will coordinate any appeal of a denial with their Regional 600 and AAS-300.
4.13.6.4.2 Waivers will be documented through the Runway Safety Area Operations Plan (a letter or memorandum of understanding between the airport operator and any organization needing access to the RSA will suffice) and an amendment to the approved ACM. Such a plan requires any organization needing access to the RSA to specify when it must access this area and what procedures it will follow to ensure compliance with RSA restrictions. Waivers will be reviewed annually at the Regional level to determine if the condition still exists and to verify stated procedures are still in use, in order to ensure the highest level of safety.
4.14 Section 139.311, Markings, Signs, and Lighting.
The certificate holder must provide and maintain markings, signs, and lighting systems 4.14.1 for air carrier operations on the airport that are authorized by the Administrator.
The ACSI must verify the marking, signs, and lighting systems are installed and 4.14.2 maintained to and in accordance with FAA standards, specifications, maintenance tolerances, and the minimum requirements as identified in the regulations. The ACSI is responsible for verifying the following information:
1. Runways are marked as appropriate for the approach with the lowest authorized minimums to meet the standards in the current version of AC 150/5340-1, Standards for Airport Markings. Runways are lighted for the approach with the lowest authorized minimums to meet the standards in the current version of AC 150/5340-30, Design and Installation Details for Airport Visual Aids.
2. Proper alignment is established for the runway lights in both directions from each end and on the centerline. The ACSI should request the lights be cycled through all intensity levels. Lights should appear to be of uniform brightness, alignment, and correct color.
3. Runway hold position markings and surface painted hold position signs must be inspected for proper placement, reflectivity, and paint scheme.
4. Instrument runways must have the appropriate color lights. Airports with air carrier operations at night or during conditions below visual flight rules (VFR) minimums or instrument meteorological conditions (IMC) are required to provide yellow edge
lights (caution zone) on the runway end opposite the landing threshold for instrument runways in accordance with AC 150/5340-30.
5. In-pavement edge light fixtures, which include touchdown zone lighting, appear to be operating and installed properly.
6. During initial and periodic inspections, when the absence of edge lights at runway/runway or runway/taxiway intersections is noted, safety is compromised. This is especially important where two or more consecutive lights are missing. Generally, these situations should be corrected by the installation of additional fixtures. In determining whether an individual semi-flush fixture needs to be installed, the ACSI should consider the following:
a. Are other visual cues available at the intersection, such as guidance signs or
centerline lighting?
b. Are the geometrics of the intersection complex?
c. Would the addition of semi-flush fixtures possibly cause the pilot more
confusion?
7. Based on the answers to the above questions, and the ACSI’s judgment that a semiflush fixture needs to be installed, the ACSI should request an immediate installation or installation in the next planned electrical project.
8. On the annual inspection report, the ACSI will document the missing fixtures and, where applicable, the steps taken for installation. This should also be documented in CCMIS under Remarks.
9. Taxiways are equipped with required centerline markings. Taxiway edge markings are required where the full-strength pavement of the taxiway is not readily discernible or where the taxiway is outlined in a large paved area such as an apron.
10. There are two types of taxiway edge markings: Continuous, to indicate that the aircraft must not cross, and Dashed, where there is a need for aircraft to cross a contiguous area. See AC 150/5340-1 for additional guidance.
11. Additionally, if the airport is open at night or during IMC conditions, the taxiways must have at least one of the following taxiway lighting systems: centerline lights, enhanced centerline lights, centerline reflectors, edge lights, or edge reflectors.
12. Guidance signs are installed in accordance with the approved airport signs and marking plan. Specifications for sign systems are contained in ACs 150/5340-18 and 150/5345-44.
13. During the first inspection after the installation of the new signs, the ACSI must verify that each sign (location, message, and color scheme) has been installed in accordance with the sign and markings plan, which is incorporated into the ACM.
14. In preparation for subsequent inspections, the ACSI should review the airport sign and markings plan as part of inspection preparation. During the inspection, the ACSI should look at the signs during the movement area drive around, noting color, lighting, message, accurate direction, and any missing signs. Physical sign and
marking layout and identifiers should be compared to the sign and marking plan to validate applicable discrepancies.
15. When a development project requires the addition of new signs or deletion of existing ones, the ACSI should verify these additions or deletions are in accordance with the sign and marking plan prior to the installation/removal of signs. Once the new signs are installed or removal takes place, the sign and marking plan must be updated and approved by the ACSI.
16. Signs must be lighted if the runway or taxiway on which they are located is lighted. Section 139.311(b)(1)(ii) and (iii) apply to all airport classes. Section 139.311(b)(1)(i) applies to Class I, II, and IV airports. Holding position signs and any co-located location signs and runway exit signs must be lighted if the runway for which they are installed is lighted, even if the taxiway on which they are installed is unlighted.
17. Plans requiring special marking and lighting are in compliance with approved standards.
18. The airport is equipped with an operable airport rotating beacon if it is open during hours of darkness or during Instrument Meteorological Conditions (IMC). ACs 150/5300-13 and 150/5340-30 contain the standards for rotating beacons.
19. Airport-owned approach lighting systems (ALSs) are properly maintained. Approach lighting owned by the airport [e.g., visual glideslope indicator systems (VGSI), runway end identifier lights (REILs), and ALSs] is covered by this section. If the airport operator owns the REIL/VGSI systems, there are also required procedures for checking calibration. Required VGSI maintenance schedules are found in AC 150/5345-26. See AC 150/5340-30 for procedures on new VGSI systems and the flight-check requirements.
20. For approach lighting systems not owned by the airport, the certificate holder is responsible for inspecting them to ensure they provide accurate reference to the airport users and for reporting any outages to the owner.
21. Obstruction lights are operable. The ACM should contain a list of lighted obstructions.
22. Marking and lighting systems on the airport are properly maintained. Properly maintained includes cleaning, replacing, or repairing any faded, missing, or nonfunctional item of the marking or lighting system; keeping each item unobscured and clearly visible; and ensuring each item provides an accurate reference and is in alignment when viewed by the user. AC 150/5340-26 discusses preventative maintenance practices for in-pavement lighting systems.
23. If the airport operator owns a standby generator for the movement area lighting, the ACM should include a method for the periodic testing of the equipment. See the manufacturer’s recommendations and AC 150/5340-30. Maintenance records of the standby generator should be available for review, and the ACSI should consider a test operation of the generator if periodic testing procedures do not appear to be adequate.
4.14.4 Land and Hold Short Operations. › 4.14.4.1 At airports where Land and Hold Short Operations (LAHSO) are…
24. Other airport lighting on the airport for aprons, roadways, buildings, and other areas are adequately adjusted or shielded to prevent interference with ATCT and aircraft operations. See AC 150/5340-30 for additional guidance.
25. The certificate holder has implemented the requirement for glass beads. See AC 150/5340-1 for the use of glass beads in 11 types of permanent pavement markings.
Restrictions to Instrument Approach Minimums. 4.14.3 On runways where non-standard edge lighting separation exists, Flight Standards may restrict minimums for Standard Instrument Approach Procedures. This is most likely in the cases of precision instrument approaches and night minimums for non-precision approaches. However, on a case-by-case basis, Flight Standards may give consideration to the presence of other runway lighting systems (e.g., centerline and touchdown zone lights) when making a decision to restrict approach minimums.
Land and Hold Short Operations. 4.14.4
4.14.4.1 At airports where Land and Hold Short Operations (LAHSO) are conducted, all LAHSO locations must have the required marking and signs, and the signs must be included in the Airport Sign and Marking plan. Both markings and signs must be examined as part of the Part 139 inspection. Hold signs are located on both sides of the runway, and signs are required to be lighted if LAHSO-Night or LAHSO-Wet is authorized.
1. Order 7110.118, Land and Hold Short Operations, addresses LAHSO, and ACSIs should refer certificate holders to the ATCT for information on their specific responsibilities for LAHSO. No waivers or exemptions will be issued to the procedures contained in Order 7110.118.
2. LAHSO can be approved for intersecting runways, intersecting taxiways, intersecting approach/departure paths, and a predetermined point on the airport.
3. LAHSO is conducted according to an LOA between the airport operator and the ATCT facility on the airport. The Part 139 involvement in LAHSO consists primarily of a review of the LOA and ACM, as well as inspection of the signs and markings.
Continue reading ↓ 120 of 392 passages shown