Radar Vectors
Advisory Circular Cancelled Issued Sep 27, 2013 AAS-100 144 pages Copy saved Nov 18, 2026

AC 150/5340-1L Standards for Airport Markings

This AC contains the FAA standards for markings used on airport runways, taxiways, and aprons.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. Department of Transportation

Federal Aviation Administration

Advisory Circular

Subject: Standards for Airport Markings

Date: 9/27/2013

Initiated by: AAS-100

AC No: 150/5340-1L

Change:

1. What is the purpose of this advisory circular (AC)?

This advisory circular (AC) contains the Federal Aviation Administration (FAA) standards for markings used on airport runways, taxiways, and aprons.

2. Does this AC cancel any prior ACs?

This AC cancels AC 150/5340-1K, Standards for Airport Markings, dated September 3, 2010.

3. To whom does this AC apply?

The FAA recommends the guidelines and standards contained herein for the marking of airport runways, taxiways, and aprons. The use of these standards is the only method of compliance with the marking of runways, taxiways, and aprons for airports certificated under Title 14 Code of Federal Regulations Part 139, Certification of Airports (Part 139). These standards are to be used on all new airport projects that are under development and are to be implemented at all Part 139 certificated airports. Further, use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and/or with revenue from the Passenger Facility Charge (PFC) Program. (See Grant Assurance No. 34, Policies, Standards, and Specifications, and PFC Assurance No. 9, Standards and Specifications.)

4. What are the principal changes in this AC? Changes are reflected by vertical bars located in the margins. This Revision:

a. Clarifies that runway surface markings on light colored pavement require black borders and glass beads (see paragraph 1.4). Airports certificated under Title 14 of the Code of Federal Regulations, Part 139, Certification of Airports, must meet these requirements within two years from the effective date of this AC.

b. Expanded and illustrated the removal of markings discussion (see paragraph 1.3.f).

c. Re-emphasizes that taxiway edge markings at entrance taxiways to a runway, including paved NO TAXI Islands are only to use dual continuous edge lines and not dual dashed edge lines (see paragraph 4.4.a). Airports certificated under Title 14 of the Code of Federal Regulations, Part 139, Certification of Airports, can meet the requirements upon the next repainting project.

ii

d. Adds a new paragraph 4.12 for ramp control markings in use by the industry and air/ramp controllers which supplements existing guidance in paragraph 4.9, Surface Painted Apron Entrance Point Signs. Note, as in this paragraph, the terms “apron” and “ramp” are used interchangeably throughout this AC. The meaning is the same. Airports certificated under Title 14 of the Code of Federal Regulations, Part 139, Certification of Airports, can meet the requirements upon the next repainting project.

e. Replaces previous references to Airport Reference Code (ARC) with Runway Design Code (RDC) and Airplane Design Groups (ADG) with Taxiway Design Groups (TDG) for taxiway designs per revised AC 150/5300-13A, Airport Design. Taxiways marked according to previous standards based on Airplane Design Groups may retain their present marking schemes until such time as the taxiway is otherwise modified under Taxiway Design Group standards. The change in design concepts principally affects taxiway fillets.

f. Placed existing Figures 1-25 and new Figure A-5 within new Appendix A. Relettered old Appendices A, B and C as new Appendix B, Appendix C, and Appendix D respectively, with no new figures.

g. Adds runway marking criteria per new Figure A-5 referenced by AC 150/5300-13A, Airport Design, for intersecting runways. Airports certificated under Title 14 of the Code of Federal Regulations, Part 139, Certification of Airports, can meet the requirements upon the next repainting project.

h. Clarifies that the intermediate holding position marking for taxiway/taxiway intersections interrupts the taxiway edge marking (see paragraph 3.6.d). Airports certificated under Title 14 of the Code of Federal Regulations, Part 139, Certification of Airports, must meet these requirements within three years from the effective date of this AC.

i. Revises guidance for intersections of ILS/MLS holding position markings and non-movement area boundary markings with taxiway edge markings (see paragraph 3.4.d and paragraph 5.4.e).

j. Adds hyperlinks to internal and external references (allowing the reader to access documents located on the internet and to maneuver within this document) that are provided throughout this document and are identified with underlined text. When navigating within this document, return to the previously viewed page by pressing the “ALT” and “” keys simultaneously.

k. Other marking changes per this revision, such as Figure A-5 and paragraphs 2.6, 3.3(d)(1) and 3.6(d), can meet the requirements upon the next repainting project.

5. How to use this AC.

a. This AC includes color-coded text boxes to emphasize safety initiatives, solutions to painting difficulties, and general remarks.

(1) Green (Painting) – explains painting precautions and solutions, such as when proportioning is permissible for runway surface markings.

iii

(2) Red (Safety) – emphasizes safety initiatives.

(3) Gray (General) – contains general remarks.

b. All references to other FAA ACs and Orders are interpreted as the current version.

c. Most figures in this advisory circular are full scale AutoCAD drawings saved as MS Word versions. For some figures, certain details may appear to be missing (missing or broken lines) when either printed or viewed on a computer monitor. To view all the details in these figures, use the appropriate ZOOM function. In some instances, where there is a large surface area, a ZOOM value of over 250% may be necessary to view all details. Both this advisory circular and the original AutoCAD files for all figures are available for download at the FAA web site:

http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.list/parentTopi cID/85.

6. How are metrics represented?

Throughout this AC, customary English units are used followed with “soft” (rounded) conversion to metric units. The English units govern.

7. How can I get this and other FAA publications?

You can view a list of all ACs at http://www.faa.gov/regulations_policies/advisory_circulars/. You can view the Federal Aviation Regulations at http://www.faa.gov/regulations_policies/faa_regulations/.

Michael J. O’Donnell Director of Airport Safety and Standards

iv

Page intentionally left blank.

v

TABLE OF CONTENTS

Chapter 1. Surface Markings for Airfield Pavements and Paved Airfield Roadways … 1

1.1. General … 1 1.2. Definitions … 1 1.3. Surface marking practices … 2 1.4. Requirements and recommendations for enhanced conspicuity of surface markings on concrete pavements and light colored pavements … 8

Chapter 2. Surface Markings for Runways … 13

2.1. Application … 13 2.2. Interruption of runway surface markings … 14 2.3. Runway landing designator marking … 16 2.4. Runway centerline marking … 18 2.5. Runway threshold marking … 19 2.6. Runway aiming point marking … 20 2.7. Runway touchdown zone marking … 22 2.8. Runway edge marking … 26 2.9. Runway displaced threshold marking … 27 2.10. Chevron markings for blast pads, stopways, and EMAS … 29 2.11. Runway shoulder marking … 29

Chapter 3. Holding Position Markings … 31

3.1. Applications of holding position markings … 31 3.2. Case 1 and Case 2 – Applications of Pattern A for the runway holding position marking on runways … 31 3.3. Case 3 – Applications of Pattern A for the runway holding position marking on taxiways … 33 3.4. Case 4 – Applications of Pattern B for the ILS/MLS holding position marking. . 36 3.5. Case 5 – Applications of Pattern B for Precision Obstacle Free Zone (POFZ) holding position marking … 38 3.6. Case 6 – Applications for Pattern C for the taxiway/taxiway intersection intermediate holding position marking … 39

Chapter 4. Surface Markings for Taxiways … 41

4.1. Application … 41 4.2. Taxiway centerline markings … 41 4.3. Enhanced taxiway centerline marking … 44 4.4. Taxiway edge marking … 47 4.5. Surface painted holding position signs … 49 4.6. Surface painted taxiway direction signs … 55 4.7. Surface painted taxiway location signs … 57 4.8. Surface painted gate destination signs … 58 4.9. Surface painted apron entrance point signs … 59 4.10. Taxiway shoulder markings … 60

vi

4.11. Geographic position markings … 61 4.12. Ramp control markings … 63

Chapter 5. Other Surface Markings … 69

5.1. Application … 69 5.2. Vehicle roadway markings … 69 5.3. Very High Frequency Omnidirectional Range (VOR) receiver checkpoint marking … 70 5.4. Non-movement area boundary marking … 70 5.5. Markings for thresholds temporarily relocated during construction … 73 5.6. Marking and lighting of permanently closed runways and taxiways … 73 5.7. Temporarily closed runways and taxiways … 73 5.8. Converting a runway to a taxiway … 74 5.9. Intermittent use of a taxiway as a runway … 75 5.10. Closed or abandoned airports … 76 5.11. Heliport markings … 76 5.12. Marking for arresting gear … 76 5.13. Hazardous construction areas … 76 5.14. Aircraft deicing facility markings … 76 5.15. Interim surface markings for taxiways mistaken as runways … 77

Appendix A. Pavement Markings … 81

Appendix B. Inscriptions for Signs and Geographic Position Markings … 109

Appendix C. Examples of Markings Outlined in Black … 115

Appendix D. Enhanced Markings for Runway Holding Position … 119

LIST OF FIGURES

Figure 1-1. Example of marking removal patterns … 4 Figure 1-2. Example of marking removal patterns … 5 Figure 1-3. Example of marking removal patterns … 6 Figure 1-4. Example of marking removal patterns … 7 Figure 1-5. Example of painted numbering system for surface painted markings … 8 Figure 2-1. Closed V geometry … 16 Figure 4-1. Sequential circular-shaped Ramp Control Markings 3, 4, and 5 between two

terminals … 64 Figure 4-2. Circular-shaped Ramp Control Marking 16 on elongated terminal apron … 65 Figure 4-3. Circular-shaped Ramp Control Markings 9S and 9N between terminals … 66 Figure 4-4. Triangular-shaped ramp control marking between terminals … 67 Figure 4-5. Circular and triangular-shaped ramp control marking dimensions … 68 Figure 5-1. Precautionary placement of the non-movement boundary marking … 72 Figure 5-2. TAXI marking location facing runway approach end … 78 Figure 5-3. TAXI marking dimensions … 79

vii

Figure 1-1: picture of page 6Figure 1-1 · page 6
Picture of the page from the copy saved here

Figure 5-4. Aviation grade artificial turf installation … 80 Figure A-1. Precision runway markings … 81 Figure A-2. Non-precision runway … 82 Figure A-3. Visual runway markings … 83 Figure A-4. Example of conflicting markings on crossing runways … 84 Figure A-5. Details of markings for intersecting runways … 85 Figure A-6. Runway designation numerals and letters … 86 Figure A-7. Displaced threshold markings … 87 Figure A-8. Marking for aligned taxiway with runway without a displaced threshold … 88 Figure A-9. Markings for blast pads and stopways … 89 Figure A-10. Markings for aligned taxiway preceding a displaced threshold … 90 Figure A-11. Markings for blast pad preceding a displaced threshold … 91 Figure A-12. Runway shoulder markings … 92 Figure A-13. Holding position marking details … 93 Figure A-14. Holding position marking details … 94 Figure A-15. Taxiway markings … 95 Figure A-16. Taxiway markings … 96 Figure A-17. Taxiway markings … 97 Figure A-18. Methods for taxiway centerline marking … 98 Figure A-19. Surface painted signs … 99 Figure A-20.

Figure 5-4: picture of page 7Figure 5-4 · page 7
Picture of the page from the copy saved here

Surface painted gate identification signs … 100 Figure A-21. Multiple gate signs … 101 Figure A-22. Surface painted apron entrance point signs … 102 Figure A-23. Taxiway shoulder markings … 103 Figure A-24. Geographic position markings … 104 Figure A-25. Vehicle roadway markings … 105 Figure A-26. VOR receiver checkpoint markings … 106 Figure A-27. Closed runway and taxiway markings … 107 Figure B-1. Pavement markings ABCDEFGH … 109 Figure B-2. Pavement markings IJKLMNOP … 110 Figure B-3. Pavement markings QRSTUVWX … 111 Figure B-4. Pavement markings YZ123456 … 112 Figure B-5. Pavement markings 7890-, … 113 Figure C-1. Runway holding position marking … 115 Figure C-2. ILS/MLS holding position marking … 115 Figure C-3. Continuous taxiway edge line marking … 116 Figure C-4. Dashed taxiway edge line marking … 116 Figure C-5. Alternate outlining method for dashed taxiway edge line marking … 117 Figure C-6. Taxiway centerline marking … 117 Figure C-7. Intermediate holding position markings … 118 Figure C-8. Non-movement area boundary marking … 118 Figure D-1.

Enhanced taxiway centerline markings … 120 Figure D-2. Dashed lines at converging taxiway centerlines … 121 Figure D-3. Converging, straight, and curved enhanced taxiway centerlines intersecting with

holding position marking … 122 Figure D-4. Enhanced runway holding position markings on taxiways … 123

viii

Figure D-5. Surface painted holding position signs for taxiway widths greater than 35 feet (10.5

m) … 124 Figure D-6. Surface painted holding position sign for taxiway widths equal to or less than 35 feet

(10.5 m) … 125 Figure D-7. Surface painted holding position signs when taxiway centerline is not perpendicular

to runway holding position marking … 126 Figure D-8. Surface painted holding position signs co-located with geographic position marking

… 127 Figure D-9. Two taxiway centerlines converging at a runway holding position marking … 128 Figure D-10. Intersection of two taxiways at runway end … 129 Figure D-11. Intersection of three converging taxiway centerlines … 130 Figure D-12. Intersection of multi-taxiway centerlines with less than 150 feet (45.7 m) between

taxiways … 131 Figure D-13. Two taxiway centerlines intersecting a runway holding position marking … 132 Figure D-14. Intersection of stub taxiway and runway … 133 Figure D-15. Narrow taxiway stacked surface painted holding position sign … 134 Figure D-16. Enhanced taxiway centerlines when a taxiway connects closely spaced runways 135

LIST OF TABLES

Table 1-1. General guidelines for determining light-colored pavements … 9 Table 1-2. Requirements and recommendations for black borders and glass beads … 10 Table 2-1. Minimum required runway surface marking schemes for paved runways … 13 Table 2-2. Number of runway threshold stripes for standard runway widths … 20 Table 2-3. Groupings of touchdown zone markings required when installed from one threshold … 23 Table 2-4. Groupings of touchdown zone markings required when installed from both thresholds … 24 Table 4-1. Placement of repetitive surface painted holding position signs and NO-TAXI islands

on taxiway entrances of over 200 feet (61 m) in width … 53

1.2. Definitions. › g. Precision Runway. For the purposes of this AC, a runway end having…

Chapter 1. Surface Markings for Airfield Pavements and Paved Airfield Roadways.

1.1. General.

This chapter provides the standards for surface markings used on paved airfield pavements (runways, taxiways, aprons) and paved airfield roadways. The standards for the surface markings assume that runways, taxiways, and aprons are built in accordance to the standard dimensions and layouts (e.g., clearances, fillets) in Advisory Circular (AC) 150/5300-13, Airport Design. The airport operator should expect difficulties when painting surface markings on non-standard infrastructure, such as a runway with a non-standard width. To assist airport operators, this advisory circular offers a few workable solutions for existing non-standard situations. Surface markings for large airplane parking positions and surface markings for unpaved airfield runways will be addressed at a future date in additional chapters.

Note: Use the zoom feature to view detail in any figure.

1.2. Definitions.

The following definitions apply to terms used in this AC.

a. Certificated Airport. An airport that has been issued an Airport Operating Certificate by the FAA under the authority of 14 CFR Part 139, Certification of Airports.

b. Commercial Service Airports and Passenger Enplanements. Defined in FAA Order 5100.38, Airport Improvement Program Handbook.

c. Displaced Threshold. A threshold that is located at a point on the runway other than the designated beginning of the runway.

d. Island. An unused paved or grassy area between taxiways, between runways, or between a taxiway and a runway. Paved islands are clearly marked as unusable, either by painting or the use of artificial turf. For the purposes of this AC, islands are also referred to as “NO-TAXI” islands.

e. Movement Area. The runways, taxiways, and other areas of an airport that are used for taxiing, takeoff, and landing of aircraft, exclusive of loading ramps and aircraft parking areas (reference 14 CFR Part 139).

f. Non-precision Runway. For the purposes of this AC, a runway end having an instrument approach procedure that provides course guidance without vertical path guidance. See AC 150/5300-13 for additional information.

g. Precision Runway. For the purposes of this AC, a runway end having an instrument approach procedure that provides course and vertical path guidance conforming to Instrument Landing System (ILS) or Microwave Landing System (MLS) precision approach standards in International Civil Aviation Organization (ICAO) Annex 10, Compliance Statement, Aeronautical Telecommunications. See AC 150/5300-13 for additional information about precision approaches.

1.3. Surface marking practices. › e. Temporary Markings. When selecting a material for temporary…

h. Threshold. The beginning of that portion of the runway that is available for landing. In some instances, the landing threshold may not coincide with the end of the opposite direction runway (see paragraph 1.2.c).

i. Visual Runway. A runway end without an existing or planned (on the Airport Layout Plan) straight-in instrument approach procedure.

1.3. Surface marking practices.

The following subparagraphs address common practices used in airport markings.

a. In some situations, these standards may call for markings with different meanings to be installed close together. Ensure that sufficient space is left between such markings such that an observer will not be confused. Note: The taxiway edge marking and non-movement area marking never coincide. See paragraph 5.4.

b. Increasing the Friction Coefficient of Surface Markings. AC 150/5370-10, Standards for Specifying Construction of Airports, Item P-620, Runway and Taxiway Painting, provides airport operators information to increase the friction coefficient of surface markings. Common practices include the spreading of silica sand on the marked surface immediately after painting and the use of glass beads in the marking materials. Glass beads or silica sand are required when durable markings (epoxy and methylacrylate based paints) are used. These paints are usually applied at 18 to 30 mils in dry thickness.

c. Paint Color Specifications, Requirements for Surface Preparation, Paint Application Rates and Methods, and Requirements for Preformed Thermal Plastic Markings. AC 150/5370-10 provides the paint color specifications, requirements for surface preparation, paint application rates, the various methods for applying paint, and the performance requirements for using only preformed thermoplastic markings. Precaution: Reflective tapes such as those commonly used for highways and city street applications are not to be used on the airside because of the potential for foreign object damage caused by loosened painted tape.

d. Striated Markings. Striated markings, which may be used in areas subject to frost heave, consist of painted stripes 4 inches (10 cm) to 8 inches (20 cm) in width that are separated by unpainted stripes. The width of the unpainted stripe may not exceed the width of the painted stripe. The width of the painted and unpainted stripes must be the same throughout the specific marking. Each edge of the marking must be a painted stripe. That is, a painted stripe is to begin and end within the width of the markings. Precaution: Because striated markings offer reduced visibility compared to non-striated markings, more frequent maintenance is required to maintain an acceptable level of visibility. Hence, striated markings are never used on Category II and Category III runways. The mixing of striated and non-striated markings is not permitted within a surface marking scheme. For example, in a 2-digit landing designator, one digit cannot be striated while the other is not. It is permitted to mix different marking schemes. For example, the landing designator is striated and the aiming point is not.

e. Temporary Markings. When selecting a material for temporary markings, consider the difficulty of removing the temporary marking when it is no longer needed. Some airports have had some success using water-based paint. Striated markings may also be used for

temporary markings, but they are never used to denote a closed runway or other closed pavement or for Category II or Category III runways.

1.3. Surface marking practices. › f. Removal of Markings. Pavement markings that are no longer needed are…

f. Removal of Markings. Pavement markings that are no longer needed are not to be painted over but instead are to be physically removed. The FAA does not endorse painting over the old markings because this inadequate practice merely preserves the old marking which, in some cases, has misled pilots and required extra maintenance. Physical removal of markings is achieved by water blasting, shot blasting, sand blasting, chemical removal, or other acceptable means that do not harm the pavement. The physical removal of any old marking(s) must include a pre-determined larger size and shape of a removal area that encompasses the old marking(s) and by grouping adjacent markings together into a larger rectangular removal area. The rationale behind this practice is to eliminate the continued visual appearance of the removed marking(s). When a runway end or threshold is being moved, all of the markings that are being removed must be strikingly larger in size, grouped together with adjacent markings and be rectangular in shape.

For example, use a single, larger rectangular removal area to encompass the entire runway designator 7 or 14L and provide a separate large rectangular area comprising all of the runway threshold markings along with a separate large rectangular area for the touchdown zone markings on the same side of the runway centerline. Also, the size and shape for the removal area for (1) Patterns A, B, and C holding position markings and (2) yellow arrow heads having a runway threshold bar or a runway demarcation bar must be much strikingly larger than the marking(s) being removed. For example, use a single, larger rectangular removal area to encompass all yellow arrow heads and the adjacent white runway threshold bar marking. See Figure 1-1, Figure 1-2, and Figure 1-3 for examples of marking removal patterns.

Note: For further details, see paragraph 1.3.f.

Figure 1-1. Example of marking removal patterns

PATTERN FOR PHYSICALLY REMOVED MARKINGS MARKINGS TO BE PHYSICALLY REMOVED

PATTERN FOR PHYSICALLY REMOVED MARKINGS

PATTERN FOR PHYSICALLY REMOVED MARKINGS

PATTERN FOR PHYSICALLY REMOVED MARKINGS

Figure 1-2: picture of page 13Figure 1-2 · page 13
Picture of the page from the copy saved here

PATTERN FOR PHYSICALLY REMOVED MARKINGS

MARKINGS TO BE PHYSICALLY REMOVED

MARKINGS TO BE PHYSICALLY REMOVED

MARKINGS TO BE PHYSICALLY REMOVED

MARKINGS TO BE PHYSICALLY REMOVED

PATTERN FOR PHYSICALLY REMOVED MARKINGS

Note: For further details, see paragraph 1.3.f.

Figure 1-2. Example of marking removal patterns

MARKINGS TO BE PHYSICALLY REMOVED

PATTERNS FOR PHYSICALLY REMOVED MARKINGS

Note: For further details, see paragraph 1.3.f.

Figure 1-3. Example of marking removal patterns

PATTERN FOR PHYSICALLY REMOVED MARKINGS

MARKINGS TO BE PHYSICALLY REMOVED

MARKINGS TO BE PHYSICALLY REMOVED

PATTERN FOR PHYSICALLY REMOVED MARKINGS

Note: For further details, see paragraph 1.3.f.

Figure 1-4. Example of marking removal patterns

MARKINGS TO BE PHYSICALLY REMOVED (TYPICAL)

MARKINGS TO BE PHYSICALLY REMOVED

PATTERN FOR PHYSICALLY REMOVED MARKINGS

PATTERN FOR PHYSICALLY REMOVED MARKINGS

RELOCATED RUNWAY HOLDING POSITION AND SURFACE PAINTED HOLDING POSITION MARKINGS

Figure 1-3: picture of page 14Figure 1-3 · page 14
Picture of the page from the copy saved here

Chapter 1. › 1.4. Requirements and recommendations for enhanced conspicuity of…

g. Painted Numbering System for Record Keeping of Surface Painted Markings. To facilitate the daily inspection, scheduled maintenance, necessary repairs, etc. for surface markings the airport operator may use a numbering system or alphanumeric system that is located in a corner of the surface marking. Figure 1-5 shows a numbering system adopted by one airport for identifying each surface marking listed in their Sign Plan. If employed, the height of the inscription should be small and inconspicuous to all viewers except an individual standing next to the surface marking.

Figure 1-5. Example of painted numbering system for surface painted markings

1.4. Requirements and recommendations for enhanced conspicuity of surface markings on concrete pavements and light colored pavements.

Figure 1-5: picture of page 16Figure 1-5 · page 16
Picture of the page from the copy saved here

Surface markings that cannot be seen by pilots and other individuals operating on paved airfield surfaces are ineffective. Two proven techniques that help airport operators enhance the conspicuity of surface markings are (1) outlining surface markings with black borders on concrete pavements and light-colored pavements and (2) placing glass beads in paint. However, glass beads are not to be used in black paint, including numerals and inscriptions found in Appendix B. Table 1-1 serves as a general guide for determining when existing asphalt concrete surfaces or asphalt treated surfaces may be classified as a light-colored pavement, i.e., when to outline a required surface marking with a black border.

(1) Surface Markings that Require Black Borders. › (ix) Intermediate holding position marking for taxiway/taxiway…

Table 1-1. General guidelines for determining light-colored pavements

Painting a Black Border Pavement Surface Type

Age of Pavement Surface 1 New Up to 2 years

old

Over 2 years

old

Portland Cement Concrete Yes Yes Yes Asphalt Concrete No No Yes Asphalt Treated No No Yes Note 1: This table serves only as a general guide since an existing asphalt pavement at one airport location may not experience the same rate of surface color deterioration as at another airport location.

a. Technique 1 – Outlining Surface Markings with Black Borders on Concrete Pavements and Light-Colored Pavements. The degree of contrast (conspicuity) between surface markings on light-colored pavements, in particular on concrete pavements and older asphalt pavements, can be increased by outlining all edges of the surface marking with a black border. Appendix B provides illustrations of recommended patterns for various surface markings outlined in black. Black borders, except for enhanced taxiway centerline applications, are 6 inches (15 cm) or greater in width to enhance the conspicuity of certain painted surface markings on concrete pavements and light-colored pavements. The borders for the outside dashes of the enhanced taxiway centerline marking can range from 3 to 6 inches (7.5 to 15 cm). See Table 1-2 for surface markings that are required or recommended to have black borders.

Surface Markings that Require Black Borders. (1)

(i) Runway centerline marking (per paragraph 2.4).

(ii) Runway threshold marking (per paragraph 2.5).

(iii) Runway displaced threshold marking (per paragraph 2.9).

(iv) Runway threshold bar marking (per paragraph 2.9.a).

(v) Runway aiming point marking (per paragraph 2.6).

(vi) Runway landing designator marking (per paragraph 2.3).

(vii) Runway touchdown zone markings (per paragraph 2.7).

(viii) All holding position markings (per paragraphs 3.2, 3.3, 3.4, and 3.5) and the non-movement area boundary marking (per paragraph 5.4).

(ix) Intermediate holding position marking for taxiway/taxiway intersections (per paragraph 3.6).

1.4. Requirements and recommendations for enhanced conspicuity of… › b. Technique 2 – Use of Glass Beads on Permanent Pavement Markings.…

(x) All taxiway centerline markings on taxi routes designated as surface movement guidance and control system (SMGCS) routes (per paragraph 4.2).

(xi) Enhanced taxiway centerline marking (per paragraph 4.3).

(xii) Surface painted holding position sign marking (per paragraph 4.5).

(xiii) Geographic position marking (per paragraph 4.11).

Surface Markings Recommended for Black Borders. This advisory (2) circular strongly recommends outlining all other markings not listed paragraph 1.4.a(1), particularly taxiway centerlines per paragraph 4.2.

Table 1-2. Requirements and recommendations for black borders and glass beads

Marking Black Border Glass Beads Runway centerline marking (per paragraph 2.4). Required Required Runway threshold marking (per paragraph 2.5). Required Required Runway displaced threshold marking (per paragraph 2.9). Required Required Runway threshold bar marking (per paragraph 2.9.a). Required Required Runway aiming point marking (per paragraph 2.6). Required Required Runway landing designator marking (per paragraph 2.3). Required Required Runway touchdown zone markings (per paragraph 2.7). Required Required Runway edge marking (per paragraph 2.8). Recommended Runway demarcation bar marking (per paragraph 2.9.c). Recommended All holding position markings (per paragraphs 3.2, 3.3, 3.4, and 3.5).

Required Required

Intermediate holding position marking for taxiway/taxiway intersections (per paragraph 3.6).

Required

Taxiway centerline markings (per paragraph 4.2). Recommended Required All taxiway centerline markings on taxi routes designated as surface movement guidance and control system (SMGCS) routes (per paragraph 4.2).

Required Required

Enhanced taxiway centerline markings per paragraph 4.3. Required Required Taxiway edge marking (per paragraph 4.4). Recommended Geographic position marking (per paragraph 4.11). Required Required Surface painted signs for holding position signs (paragraph 4.5), taxiway direction signs (paragraph 4.6), taxiway location signs (paragraph 4.7), gate destination signs (paragraph 4.8), and apron entrance point signs (paragraph 4.9).

Required Required

Non-movement area boundary marking (per paragraph 5.4). Required Required All other markings not listed paragraph 1.4.a(1). Recommended

b. Technique 2 – Use of Glass Beads on Permanent Pavement Markings. Glass beads identified in Item P-620 of AC 150/5370-10 are an effective means of enhancing the conspicuity of surface markings when aircraft and vehicles operate at night, during low-visibility

conditions, or when the pavement surface is wet. The glass beads used in the below applications should meet the specifications found in AC 150/5370-10, Item P-620. Due to the additional increase in marking conspicuity caused by certain glass beads, the FAA recommends that runway holding position markings contain either Type III or Type IV glass beads as determined by the airport operator. If Type IV glass beads that have a larger diameter are used, then they should only be applied in higher-built materials, such as TT-P-1952E-Type III waterborne paint, epoxy, methyl methylacrylate, or preformed thermoplastic. Precaution: Glass beads should never be used in black paint, including numerals and inscriptions found in Appendix B. See Table 1-2 for surface markings that are required or recommended to have glass beads.

Glass Bead Requirement Per AC 150/5370-10, Paragraph 620-3.5, Application

(General) “Glass beads shall be distributed upon the marked areas at the locations shown on the plans to receive glass beads immediately after application of the paint. A dispenser shall be furnished that is properly designed for attachment to the marking machine and suitable for dispensing glass beads. Glass beads shall be applied at the rate(s) shown in Item P-620, Table 1 of AC 150/5370-10. Glass beads shall not be applied to black paint or green paint, including numerals and inscriptions found in Appendix B. Type III beads shall not be applied to red or pink paint. Glass beads shall adhere to the cured paint or all marking operations shall cease until corrections are made. Different bead types shall not be mixed. Regular monitoring of glass bead embedment should be performed.”

Page intentionally left blank.

2.1. Application. › b. Runways with a displaced threshold, blast pad, stopway, or extra…

Chapter 2. Surface Markings for Runways.

2.1. Application.

The minimum requirements for surface marking schemes used for runways are a direct function of the approach category for each runway threshold and the existence of displaced thresholds, stopways, blast pads, or extra wide shoulders. Runways having the same approach category off both runway thresholds will show the same surface marking scheme from threshold to threshold (with some exceptions, such as the runway designator.) In comparison, runways with different approach categories will show two different surface marking schemes. The complete runway surface marking schemes required by a runway combine Table 2-1 requirements with the physical structure, such as blast pads or stopways, and usage of the runway.

a. Table 2-1 identifies the minimum required surface marking schemes for paved runways according to their threshold approach category. Figure A-1, Figure A-2, Figure A-3, and Figure A-6 provide the dimensional standards for the surface marking schemes. An airport operator may paint a runway with additional surface marking schemes than required, such as a visual runway with runway edge markings or the aiming point marking, if deemed necessary by the FAA. Furthermore, surface markings beyond those described in Table 2-1 are required to support particular operations, such as a displaced threshold, or to identify runway related features, such as blast pads or stopways.

Table 2-1. Minimum required runway surface marking schemes for paved runways

Threshold Approach Category Runway Surface Marking

Scheme

Visual Approach

Non-precision

Approach (and approaches with vertical guidance not lower

than ¾ -statute mile

visibility)

Precision Approach (Approaches with lower

than ¾ -statute mile

visibility)

Landing Designator (par. 2.3) X X X Centerline (par. 2.4) X X X Threshold Markings (par. 2.5) Note 1 X X Aiming Point (par. 2.6) Note 2 Note 3 X Touchdown Zone (par. 2.7) X Edge Markings (par. 2.8) Note 4 Note 4 X Note 1: Required on runways serving approach categories C and D airplanes and for runways used, or intended to

be used, by international commercial air transport. Note 2: Required on 4,200-foot (1,280 m) or longer runways serving approach categories C and D airplanes. Note 3: Required on 4,200-foot (1,280 m) or longer instrumented runways. Note 4: Used when the full runway pavement width may not be available for use as a runway.

b. Runways with a displaced threshold, blast pad, stopway, or extra wide shoulders require additional marking schemes not identified in Table 2-1. These surface marking schemes and others not in Table 2-1 are discussed separately in this advisory circular. See AC 150/5300- 13 for detailed information about the location of displaced thresholds, blast pads, and stopways.

2.2. Interruption of runway surface markings. › b. Lesser Precedence Runways. The manner in which a lesser precedence…

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

(Painting) The dimensional size for the runway surface marking promulgated by this advisory circular is based on the assumption that the runway has a standard runway width as prescribed by AC 150/5300-13. For convenience, the standard widths are shown in Table 2-2. below.

Airport operators with non-standard runway widths may, for specified surface markings, proportionally adjust the marking’s width to be less than the standard scheme. Under substandard conditions, the width of marking is in direct proportion to the available runway width. However, the corresponding length for the marking is never reduced.

Subsequent paragraphs in this advisory circular will specify, via a green-shaded solution box, those runway surface markings that may be proportioned. The absence of a greenshaded solution box in a subsequent paragraph implies that runway surface marking, such as the runway centerline, is not to be decreased in width even if other nearby runway surface markings are proportionally adjusted.

2.2. Interruption of runway surface markings.

At the intersection of two runways, the surface markings of one runway are, with the possible exception of runway edge markings (such as closed V-shaped runways), fully displayed through the intersection while the surface markings of the other runway are completely interrupted. This process of removing runway surface markings from one runway establishes an order of precedence among the different runways.

a. Order of Precedence. The order of precedence for displaying the runway surface marking schemes of one runway over the other runway at the intersection of these runways should follow this order:

Precision approach runway, Category III. (1)

Precision approach runway, Category II. (2)

Precision approach runway, Category I. (3)

Non-precision approach runway. (4)

Visual runway. (5)

For an intersection of runways of the same precedence, the preferred higher precedence runway is the one having the lowest approach minimums or the runway end most often used.

b. Lesser Precedence Runways. The manner in which a lesser precedence runway intersects a higher precedence runway may require the shifting or complete removal of certain surface markings that fall within the intersection. As shown in Figure A-4, the most affected surface markings are the runway centerline, runway edge markings, aiming point markings, and

2.2. Interruption of runway surface markings. › d. Closed V-Shaped Runway Ends Configuration. The closed V-shaped…

runway touchdown zone markings. The latter two runway markings may have implications when shifted or removed. See paragraphs 2.2.c and 2.6 for shifting an aiming point marking, and see paragraph 2.7 for removing touchdown zone markings.

c. Consequences When Shifting the Aiming Point Markings. Figure A-4 shows one possible conflict that could occur when the aiming point markings are relocated.

When the aiming point markings of a given runway that are in the (1) intersection of two runways need to be moved more than 200 feet (61 m) away from the existing threshold, the airport operator will have to displace the existing threshold or designate a new runway end (threshold) in order to retain the distance between the threshold and the aiming point marking as illustrated in the bottom illustration of Figure A-4. The preferred distance to be maintained between the newly designated threshold and the shifted aiming point marking is 1,020 feet (311 m); see paragraph 2.6.

Runways with an approach landing aid, such as Precision Approach Path (2) Indicators (PAPIs) or Visual Approach Slope Indicators (VASIs), which are co-located with the aiming point markings, can be negatively affected when an excessive shifting of the aiming point marking occurs. The consequence could be a non-compatible threshold crossing height for landing airplanes. When the aiming point markings are shifted more than 60 feet (18.3 m), the co-located PAPI or VASI should be evaluated for relocation to provide a correct vertical guidance to pilots. See AC 150/5340-30, Design and Installation Details for Airport Visual Aids, to determine if the impact of shifted aiming point markings warrants a relocation of the colocated PAPI (or other runway approach aids).

For landing safety, the FAA requires that whenever the distance between (3) the threshold and aiming point markings is 1,220 feet (372 m) or more, the airport operators place a note in the Airport/Facility Directory (A/FD) to inform pilots about the increased distance existing between the threshold and the aiming point markings.

d. Closed V-Shaped Runway Ends Configuration. The closed V-shaped runway ends configuration is a pavement geometry where two runway ends commence from the same location but proceed in different directions (see Figure 2-1). This undesirable geometry requires a special shifting procedure of the runway landing designator marking of the lesser precedence runway farther down the runway than prescribed by paragraph 2.3. The special procedure is as follows. On the lesser order runway, locate the point on its runway centerline that is perpendicular to the inside common corner of the two intersecting runways. Once this base point is located, move this base point 20 feet (6.5 m) down the runway centerline to relocate the bottom of the letter or number(s) used for the runway landing designator. For an intersection of runways of the same precedence, the preferred higher precedence runway is the one having the lowest approach minimums or the runway end most often used.

Figure 2-1: picture of page 24Figure 2-1 · page 24
Picture of the page from the copy saved here

e. Characteristics. › (1) A runway landing designator marking consists of a number comprising…

1

Figure 2-1. Closed V geometry

Wrong-Runway Takeoffs Mitigation

(Safety) In an effort to eliminate the possibility of a “wrong-runway” takeoff operation by pilots, the airport operator should reconstruct closed V-shaped runway geometries to a different geometry, possibly an X-shaped geometry.

2.3. Runway landing designator marking.

a. Purpose. The runway landing designator marking identifies a runway end.

b. Requirement. See Table 2-1.

c. Location. Runway landing designator marking(s) must be located from the runway threshold per Figure A-1, Figure A-2, Figure A-3, or from the displaced threshold per Figure A-8. All these figures show the start location for both types of thresholds.

d. Color. Runway landing designator markings are white. See paragraph 1.4 for required and recommended techniques to enhance visibility of this surface marking.

e. Characteristics.

A runway landing designator marking consists of a number comprising (1) one or two digits. When parallel runways exist, the number is further supplemented with a letter.

e. Characteristics. › (6) There are certain runway placements where the surface marking…

A single-digit runway landing designation number is never preceded by a (2) zero.

For single runways, dual parallel runways, and triple parallel runways, the (3) designator number is the whole number nearest the one-tenth of the magnetic azimuth along the runway centerline when viewed from the direction of approach. For example, where the magnetic azimuth along the runway centerline is 183 degrees, the runway designator marking would be 18; for a magnetic azimuth of 87 degrees, the runway designation marking would be 9. For a magnetic azimuth ending in the number “5” such as 185 degrees, the runway designator marking may be either 18 or 19.

On four or more parallel runways, one set of adjacent runways is (4) numbered to the nearest one-tenth of the magnetic azimuth and the other set of adjacent runways is numbered to the next nearest one-tenth of the magnetic azimuth.

For parallel runways, each runway landing designator number must be (5) supplemented by a letter, in the order shown from left to right when viewed from the direction of approach as prescribed by the following marking criteria. Different labeling patterns than those prescribed below are permissible under certain circumstances as identified in paragraph 2.3.e(6)

(i) Two parallel runways having a magnetic azimuth of 182 degrees are designated “18L” and “18R.”

(ii) Three parallel runways having a magnetic azimuth of 87 degrees are designated “9L,” “9C,” and “9R.”

(iii) Four parallel runways having a magnetic azimuth of 324 degrees are designated “32L,” “32R,” “33L,” and “33R.”

(iv) Five parallel runways having a magnetic azimuth of 138 degrees are designated “13L,” “13R,” “14L,” “14C,” and “14R” or “14L,” “14R,” “13L,” “13C,” and “13R.” Other combinations exist for this case. See paragraph 2.3.e(6).

(v) Six parallel runways having a magnetic azimuth of 83 degrees are designated “8L,” “8C,” “8R,” “9L,” “9C,” and “9R. See paragraph 2.3.e(6).

(vi) Seven parallel runways having a magnetic azimuth of 85 degrees – the runways would be designated “8L,” “8C,” “8R,” “9L,” “9C,” “9R,” and “10.” Other combinations exist for this case. See paragraph 2.3.e(6).

There are certain runway placements where the surface marking schemes (6) for parallel runways provided in paragraph 2.3.e(5) may not be appropriate because their orientation may lead to pilot confusion. For example, the marking scheme recommended for parallel runways on the same side of a terminal is to follow paragraph 2.3.e(5). However, when two parallel runways are separated by a large distance, as by a central terminal or several terminals, it is preferable to designate the runways as non-parallel runways to avoid pilot confusion. Another case that may cause pilot confusion is a turf runway that is parallel to paved visual runway but at a great distance from a higher precedence paved runway. In general, the

e. Characteristics. A runway centerline marking consists of a line of… › (2) The minimum width of the stripes is:

airport operator should carefully choose how to mark parallel runways to eliminate pilot confusion.

The appearance of the letters and numbers used for runway landing designator markings are in the form and proportion as shown in Figure A-6. The spacing between numbers and letters are as shown in Figure A-1, Figure A-2, Figure A-3, and Figure A-6. However, with the exception of the numerals 6 and 9, all numerals and the letters L, C, and R are 60 feet (18.3 m) in height. Numerals 6 and 9, which are 63 feet (18.9 m) in height, follow the Rule of 69. That is, although the numerals 6 and 9 are taller, the 3-foot tips of the numerals are ignored so that their separations from the threshold markings, the letters L-C-R, the first runway centerline, and the start of the runway threshold remain as shown in Figure A-1, Figure A-2, and Figure A-3.

Application of Proportioning Runway Markings for Airplane Design Group (ADG) I Runway Width

(Painting) Due to the space limitations on very narrow runways, the size and spacing of the numbers and letters are reduced only when necessary such that the painted runway landing designator is no closer than 2 feet (0.6 m) from the runway edge or runway edge markings. For example, this problem may occur when painting certain dualnumbered runway landing designators spaced 15 feet (4.5 m) apart on an ADG I runway width of 60 feet (18.3 m). In such cases, first reduce the 15-foot (4.5-m) spacing to 10 feet (3.1 m) and retain the size of numerals and letter per Figure A-6. Second, reduce the 15-foot (4.5-m) spacing to 10 feet (3.1 m) and reduced the size of numerals and letter proportionally to maintain the 2-foot (0.6-m) edge or runway edge markings clearance.

2.4. Runway centerline marking.

a. Purpose. The runway centerline marking identifies the physical center of the runway width and provides alignment guidance to pilots during takeoff and landing operations. For lighting provisions, see AC 150/5340-30.

b. Requirement. See Table 2-1.

c. Location. A runway centerline marking is located along the physical center of the runway width and spaced between the runway landing designation markings as shown in Figure A-1, Figure A-2, and Figure A-3.

d. Color. The runway centerline marking is white. See paragraph 1.4 for required and recommended techniques to enhance this surface marking.

e. Characteristics. A runway centerline marking consists of a line of uniformly spaced stripes and gaps and of uniform width.

The stripes are 120 feet (36.5 m) in length and the gaps are 80 feet (24.3 (1) m) in length.

The minimum width of the stripes is: (2)

e. Characteristics. The runway threshold marking consists of a pattern… › (1) Table 2-2.

 36 inches (90 cm) for precision runways.

 18 inches (45 cm) for non-precision runways.

 12 inches (30 cm) for visual runways.

To accommodate varying runway lengths, all adjustments to the uniform (3) pattern of runway centerline stripes and gaps are made near the runway midpoint (defined as the distance between the two thresholds or displaced thresholds). Under such cases, reduce the lengths of both the stripes and gaps starting from midpoint and proceed toward the runway thresholds. Reduced stripes must be at least 80 feet (24 m) in length, and the reduced gaps must be at least 40 feet (12.3 m) in length. The affected stripes and gaps within the section should show a uniform pattern.

2.5. Runway threshold marking.

a. Purpose. A runway threshold marking, commencing 20 feet (6 m) from the actual start point of runway threshold, closely identifies the actual beginning point of the runway threshold used for landings. For lighting provisions, see AC 150/5340-30.

b. Requirement. See Table 2-1.

c. Location. The runway threshold marking starts 20 feet (6 m) from the actual start point of the runway threshold as shown in Figure A-1 and Figure A-2. This value remains the same even though a 10-foot (3-m) white threshold bar is introduced, such as for displaced thresholds or the addition of a blast pad or stopway, as shown in Figure A-9. Previously, when a displaced threshold was painted or a blast pad or stopway added, the 20-foot (6-m) dimension was increased to 30 feet (9 m) to accommodate the requirement for painting the runway threshold bar. When any runway threshold or displaced threshold is remarked with threshold bar markings, or when a blast pad or stopway is added, the separation is 10 feet (3 m) as shown in Figure A-8.

d. Color. The components of a runway threshold marking are white. See paragraph 1.4 for required and recommended techniques to enhance this surface marking.

e. Characteristics. The runway threshold marking consists of a pattern of longitudinal stripes of uniform dimensions spaced symmetrically about the runway centerline. The number of longitudinal stripes and their spacing is determined by the runway width.

Table 2-2. provides the number of longitudinal stripes for runways having (1) standard runway widths as defined by AC 150/5300-13. Figure A-1 illustrates the pattern for a 150-foot (45-m) wide runway. See paragraph 2.5.e(3) for painting guidance applicable to nonstandard runway widths.

2.6. Runway aiming point marking. › b. Requirement. See Table 2-1.

Table 2-2. Number of runway threshold stripes for standard runway widths

Standard runway widths Number of symmetrical stripes 60 feet (18.3 m) 4 75 feet (22.9 m) 6 100 feet (30.5 m) 8 150 feet (45.7 m) 12 200 feet (61 m) 16

For standard runway widths, the longitudinal stripes are 150 feet (45.7 m) (2) long and 5.75 feet (1.75 m) wide with the outer edges spaced (stripe-gap) 5.75 feet (1.75 m) apart. However, the two longitudinal stripes nearest the runway centerline are doubled spaced, i.e., outer edges of the near-most pair are 11.5 feet (3.5 m) apart. Figure A-1 illustrates the stripegap pattern for 150-foot (46-m) wide runways. The stripe-gap pattern allows sufficient room to paint runway edge markings without interfering with the outermost longitudinal stripes.

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

(Painting) For standard 75-foot (23-m) wide runways that use 36-inch (90-cm) wide runway edge markings, the stripe-gap pattern of 5.75 feet (1.75 m) is reduced to 5.50 feet (1.68 m).

For non-standard runway widths, the same stripe-gap pattern is continued (3) from the runway centerline until the outermost longitudinal stripe is not closer than 4 feet (1.2 m) from the runway edge. For example, for a non-standard 125-foot (38-m) wide runway, the stripegap pattern yields a total of 10 longitudinal stripes symmetrical about the runway centerline. In no case should the stripe-gap pattern exceed 92 feet (27 m) on either side of the runway centerline. The value of 92 feet (27 m) is the width for the pattern used on the standard 200-foot (61-m) wide runways.

When there is pavement in excess of 5 feet (1.5 m) prior to the actual start (4) of the runway threshold and (a) pilots may confuse the pavement as part of the actual runway or (b) the pavement does not have the same load bearing capacity as the runway, then painting of a runway threshold bar per paragraph 2.9 is required. In contrast, if the installation of landing threshold lights requires pavement to support the light fixtures and the supportive pavement abuts the start point of the runway threshold, then the supportive pavement is not considered a part of the runway. In this instance, the painting of a runway threshold bar is not required.

2.6. Runway aiming point marking.

a. Purpose. A runway aiming point marking provides a visual aiming point for landing operations.

b. Requirement. See Table 2-1.

(2) The width of each rectangular marking is as follows: › (iii) 15 feet (5 m) for standard runway widths of 75 feet (22.9 m).

c. Location. The preferred beginning of the aiming point marking starts 1,020 feet (311 m) from the runway threshold as shown in Figure A-1, Figure A-2, and Figure A-3. However, this preferred separation is not adequate for all cases as partially discussed below.

Note: The term preferred assumes the following conditions: standard visual glide slope of 3 degrees; no obstacle in the approach area affecting the obstacle clearance surface of the PAPI; standard threshold crossing heights per AC 150/5340-30; sufficient runway length so not to force the placement of the aiming point marking; no rapid terrain drop off near the approach threshold that encounters severe turbulence; no elevation differences between the threshold and the installation zone of the PAPI.

Intersecting Runways. A separation tolerance of plus or minus 200 feet (1) (61 m) is allowed when it is necessary to shift the aiming point marking to avoid overlapping aiming point markings at dual runway intersection as shown in Figure A-4 and Figure A-5, and discussed in paragraph 2.2.c. However, depending on the threshold crossing heights and the available runway approach aids, the shifting of the aiming point markings may negatively impact the threshold crossing heights for approaching airplanes. One potential impact of the shift is to the co-located runway approach aids, such as the PAPI, in which the previous vertical guidance offered by the aiming point marking to pilots is now incompatible with the threshold crossing height associated with the runway approach aid. Under such conditions, adjustment in the location of the affected runway approach aid may be necessary after an evaluation so that the colocated relationship between the PAPI (and other approach aids) and the shifted aiming point marking permits an acceptable landing operation for both landing aids.

Compatible Threshold Crossing Heights. See AC 150/5340-30 to (2) determine if the impact of a relocated aiming point marking warrants relocating the co-located PAPI (or other runway approach aids).

d. Color. The runway aiming point marking is white. See paragraph 1.4 for required and recommended techniques to enhance this surface marking.

e. Characteristics.

The runway aiming point marking consists of two conspicuous rectangular (1) markings, 150 feet (45.7 m) in length for runways of at least 4,200 feet (1280 m) in length between the thresholds (or a displaced threshold(s)) and 100 feet (30.5 m) in length for lesser lengths between the thresholds (or a displaced threshold(s)), that are located symmetrically on each side of the runway centerline as shown in Figure A-1, Figure A-2, and Figure A-3. See Table 2-2. for the dimensions of standard runway widths per AC 150/5300-13.

The width of each rectangular marking is as follows: (2)

(i) 30 feet (9.1 m) for standard runway widths of 150 feet (45.7 m) or greater.

(ii) 20 feet (6 m) for standard runway widths of 100 feet (30.5 m).

(iii) 15 feet (5 m) for standard runway widths of 75 feet (22.9 m).

(iv) 12 feet (3.7 m) for a standard runway width of 60 feet (18.3 m).

The lateral spacing between the inner sides of the runway aiming point (3) markings is as follows:

(i) For runways of 150 feet (45.7 m) or more in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 72 feet (21.9 m).

2.7. Runway touchdown zone marking. › a. Purpose. For landing operations, the touchdown zone marking…

(ii) For runways of 100 feet (30.5 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 48 feet (14.6 m).

(iii) For runways of 75 feet (22.9 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 36 feet (11.0 m).

(iv) For runways of 60 feet (18.3 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 28.8 feet (8.8 m).

Application of Proportioning Runway Markings

for Non-Standard Runway Widths and for Standard Runway Widths less than 150 feet (45.7 m)

(Painting) For runways with widths below 150 feet (45.7 m), the width of the rectangular bars and their lateral spacing between the inner sides of the rectangular bars are adjusted in proportion to the available runway width by using the 150-foot (45.7-m) width runway parameters to determine the percentage decrease in lateral spacing and width of each marking. For example, a non-standard 70-foot wide runway would apply 70/150 = 0.467 to obtain a lateral spacing of 72 × 0.467 = 33.6 feet (10.25 m) between the pair and an individual width of 30 × 0.467 = 14 feet (4.27 m).

If runway edge markings are also painted, which are not reduced, then the adjustment should add the width of the corresponding runway edge markings plus a minimum 1-foot (0.3-m) clearance between the outer edge of the aiming point marking and the runway edge marking.

Lateral spacing – in no case is the lateral spacing less than 30 feet (9.1 m) except for runways less than 75 feet (22.9 m).

Lengths – in all cases, the length of the aiming point marking remains unchanged.

2.7. Runway touchdown zone marking.

a. Purpose. For landing operations, the touchdown zone marking identifies the touchdown zone along a precision runway in 500-foot (152-m) increments. For lighting provisions, see AC 150/5340-30.

b. Requirement. See Table 2-1.

c. Location. The touchdown zone marking consists of symmetrically arranged pairs of rectangular bars in groups of one, two, and three along the runway centerline as shown in Figure A-1. As shown, there are five groupings with the aiming point marking serving as an independent, sixth pair.

c. Location. The touchdown zone marking consists of symmetrically… › (1) The touchdown zone marking scheme maintains a 900-foot (275-m)…

The touchdown zone marking scheme maintains a 900-foot (275-m) (1) “no-marking zone” from the midpoint of the runway back toward the threshold. That is, those pairs of surface markings that extend within 900 feet (275 m) of the runway midpoint are eliminated. The intent of this painting practice is to preserve a 1,800-foot (550-m) unmarked area so pilots do not confuse the surface markings during a landing with the surface markings for the other approach procedure. The same practice applies equally to a displaced threshold, i.e., the midpoint is located between the thresholds or displaced thresholds and not the runway ends. Taking this into consideration, the painted pattern for the runway touchdown zone marking depends on the (a) authorized approach off each runway and (b) the available length between the runway thresholds or displaced threshold, i.e., the midpoint. The surface marking patterns for the two possible cases are provided in Table 2-3 (case #1) and Table 2-4 (case #2).

Case #1 – Only one runway end requires the runway touchdown zone marking scheme. Apply Table 2-3 criteria, which take into account the “no-marking zone” of 900 feet (275 m) from the midpoint back toward the threshold.

Table 2-3. Groupings of touchdown zone markings required when installed from one

threshold

Distance Between Thresholds

(or displaced thresholds)

Markings for Precision Approach End (includes

displaced threshold)

Other Runway End Visual or Non-precision

6,065 ft (1849 m) or greater1 Full set of markings Aiming point marking 5,565 ft (1697 m) to 6,064 ft (1848 m) Less one grouping of rectangular

bar markings2

Aiming point marking

5,065 ft (1544 m) to 5,564 ft (1696 m) Less two groupings of rectangular bar markings

Aiming point marking

4,565 ft (1391 m) to 5,064 ft (1543 m) Less three groupings of rectangular bar markings

Aiming point marking

Note 1: The value of 6,065 feet is derived as follows. For the non-precision or visual runway end, the table assumes the 900-foot “no-marking zone” criterion plus the length of a preferred aiming point marking, which starts 1,020 feet from the start of the threshold to obtain a length of 1,920 feet. Add to this the length of the aiming point marking. Per paragraph 2.6.e(1), the length of the aiming point marking is either 150 feet or 100 feet. This table uses a length of 150 feet because all the entries in column #1 are greater than 4,200 feet. Therefore, adding 150 feet to 1,920 feet obtains a length of 2,070 feet. For the precision end, which equals 3,995 feet, it assumes the 900-foot “no-marking zone” followed by the standard 75-foot-long rectangular bar for a total length of 975 feet. Add to this value the full 3,000-foot touchdown zone marking scheme and the 20-foot separation between the actual starting point of the runway threshold (or displaced threshold) and the bottom edge of threshold marking to obtain 3,995 feet.

c. Location. The touchdown zone marking consists of symmetrically… › (2) Because the location of the aiming point marking may be adjusted…

Distance Between Thresholds

(or displaced thresholds)

Markings for Precision Approach End (includes

displaced threshold)

Other Runway End Visual or Non-precision

Summing the values 3,995 and 2,070 yields 6,065 feet.

Note 2: Each reduction in a pair of rectangular bar markings from the precision end equates to a 500-foot (152-m) reduction between the thresholds.

The painting rationale for this table is to ignore the midpoint between the thresholds so the precision instrumented landing is favored over non-precision or visual landings. That is, the length of the non-precision/visual side of the runways always remains at 2,070 feet in length to promote the painting of a full set of touchdown zone markings.

Case #2 – Both runway ends require runway touchdown zone markings. Apply Table 2-4 criteria, which take into account the “no-marking zones” of 1,800 feet (550 m) from the threshold-to-threshold midpoint.

Table 2-4. Groupings of touchdown zone markings required when installed from both

thresholds

Distance Between Thresholds

(or displaced thresholds)

Markings for Each Threshold

(or displaced threshold) 7,990 ft (2436 m) or greater1 Full set of markings 6,990 ft (2130 m) to 7,989 ft (2435 m) Less one grouping of rectangular bars from each

side nearest to the runway midpoint2 5,990 ft (1826 m) to 6,989 ft (2129 m) Less two groupings of rectangular bars from

each side nearest to the runway midpoint2 4,990 ft (1521 m) to 5,989 ft (1825 m) Less three groupings of rectangular bars from

each side nearest to the runway midpoint2

Note 1: The value of 7,990 feet is derived as follows. Proceed from the runway midpoint in one direction, and you will have the 900-foot “no-marking zone” criterion followed by the standard 75-foot long rectangular bar for a total length of 975 feet. Add to this value the full 3,000-foot touchdown zone marking scheme plus the 20-foot separation between the actual starting point of the runway threshold (or displaced threshold) and the edge of threshold marking to obtain 3,995 feet. Double this value for both directions to obtain 7,990 feet.

Note 2: Each reduction in a grouping of rectangular bar markings from both sides equates to a 1,000-foot (305-m) reduction between the thresholds.

The painting rationale for this table is to preserve the midpoint between the thresholds, thereby promoting an equal treatment of painting groupings of rectangular bar markings for both sides.

Because the location of the aiming point marking may be adjusted from (2) the threshold to accommodate different approach slopes and/or heights over the threshold and to possibly take into account non-zero runway gradients, the location of an adjusted aiming point marking will vary. Please see AC 150/5340-30. Under such conditions, an adjusted aiming point

(3) The lateral spacing between the inner sides of the rectangular bars… › (iv) For runways of 60 feet (18.3 m) in width, the lateral spacing…

will, in most cases, continue to be located between the first and the second touchdown zone markings. However, when the accumulative effect of the adjustments is severe (defined as when a touchdown zone marking coincides with or is within 160 feet (48.8 m) of the adjusted aiming point marking), that touchdown zone marking must not be painted. For the pilot community, this practice permits the aiming point marking to retain its prominent visual landing aid as compared to a touchdown zone marking.

d. Color. All rectangular bars are white. See paragraph 1.4 for required and recommended techniques to enhance this marking.

e. Characteristics.

For runway widths of 150 feet (45.7 m) or greater, each rectangular bar is (1) 75 feet (22.9 m) long and 6 feet (1.8 m) wide. The lateral spacing between the inner sides of the rectangular bars on the same side of the runway centerline is 5 feet (1.5 m).

For runway widths less than 150 feet (45.7 m), the length of the marking (2) remains unchanged, but the width and the lateral spacing between the markings are reduced proportionally to the decrease in runway width by using 150-foot (45.7 m) parameters to determine the percentage decrease.

The lateral spacing between the inner sides of the rectangular bars (3) centered along the runway centerline is equal to that of the aiming point marking (criteria repeated below from paragraph 2.6.e(3)). In all cases, the length of the rectangular bars (and the aiming point markings) remains unchanged. See Table 2-2. for the dimensions of standard runway widths.

(i) For runways of 150 feet (45.7 m) or more in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 72 feet (21.6 m).

(ii) For runways of 100 feet (30.5 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 48 feet (14.6 m).

(iii) For runways of 75 feet (22.9 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 36 feet (11.0 m).

(iv) For runways of 60 feet (18.3 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 28.8 feet (8.8 m).

e. Characteristics. The runway edge marking has a minimum width of 36… › (2) Where an aligned taxiway, as shown in Figure A-8 and Figure A-10,…

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

(Painting) For runways with widths below 150 feet (45.7 m), the width of the rectangular bars and their lateral spacing between the inner sides of the rectangular bars are adjusted in proportion to the available runway width by using the 150-foot (45.7 m) width runway parameters to determine the percentage decrease in lateral spacings and width of the marking. For example, a nonstandard 70-foot wide runway would apply 70/150 = 0.467 to obtain a lateral spacing for the centered pair of 72 × 0.467 = 33.6 feet (10.25 m), a lateral spacing for other pairs of 5 × 0.467 = 2.3 feet (0.7 m), and a width of 6 feet × 0.467 = 2.8 feet (0.85 m). This adjustment must be such that the inner sides of the innermost rectangular bars to the runway centerline align themselves with the inner side of the aiming point marking. Given that the runway edge markings are painted, the adjustment should be such that the clearance between the runway side strip and the outer edge of the three-bar grouping is a minimum of 1-foot (0.3-m). In no case should the three-bar group be painted farther out from the runway centerline than the aiming point marking.

2.8. Runway edge marking.

a. Purpose. The runway edge marking provides enhanced visual contrast between the runway edge and the surrounding terrain or runway shoulders and delineates the width of suitable paved area for runway operations. For lighting provisions, see AC 150/5340-30.

b. Requirement. See Table 2-1.

c. Location. The runway edge marking consists of two parallel stripes, one placed along each edge of the usable runway with the outer edge of each stripe approximately on the edge of the paved useable runway. For extra wide runways, such as military runways converted for public use, the maximum distance between the outer edges of the parallel stripes is 200 feet (61 m). Figure A-1 illustrates the runway edge marking.

d. Color. The stripes of the runway edge marking are white. See paragraph 1.4 for required and recommended techniques to enhance this marking.

e. Characteristics. The runway edge marking has a minimum width of 36 inches (90 cm) for runways of 100 feet (30.5 m) or wider in width and at least 18 inches (45 cm) on smaller width runways (see Table 2-2. for standard runway widths).

For runways with a displaced threshold, the edge markings continue (1) through the paved area prior to the displaced threshold as shown Figure A-8. This continuation of the edge markings is required because this paved area is used for takeoffs and landing rollouts from the other direction.

Where an aligned taxiway, as shown in Figure A-8 and Figure A-10, (2) precedes a runway threshold, both edge markings will terminate. The point of termination of the edge markings is determined by the taxiway geometry. Prohibited: The conversion of a runway

(1) Purposes. › (i) Figure A-8 illustrates the predominant case in which the threshold…

section into an aligned taxiway or the construction of a new aligned taxiway. See AC 150/5300- 13. The FAA further recommends that existing aligned taxiways be removed or reconfigured into usable runways, for example, as shown in Figure A-7 and Figure A-11. When a taxiway connects to a runway or the runway has turn pads or turnarounds, the runway edge marking remains continuous between the runway and these adjoining infrastructures.

For intersecting runways, see guidance in paragraph 2.2. (3)

2.9. Runway displaced threshold marking.

The marking scheme for a runway with a displaced threshold, when required by paragraph 2.1, includes a runway threshold bar and arrowheads with and without arrow shafts. Figure A-7, Figure A-10, and Figure A-11 illustrate the various applications of displaced thresholds and the requirement for additional marking components. For lighting provisions, see AC 150/5340-30.

a. Runway Threshold Bar Marking.

Purpose. The runway threshold bar marking delineates the beginning (1) section of the runway available for landing from the unusable section on the approach side of the displaced threshold or prepared surfaces for a blast pad, stopway, EMAS or end of an aligned taxiway.

Requirement. Install a runway threshold bar marking when there is an (2) unusable section, blast pad, stopway, EMAS, or aligned taxiway on the approach side of the threshold.

Location. The runway threshold bar marking is an elongated rectangular (3) bar that is located perpendicular to the runway centerline and on the landing portion of the runway. The outboard edge of the marking is aligned with the location labeled “start of runway displaced threshold” as shown in Figure A-8.

Color. The runway threshold bar marking is white. See paragraph 1.4 for (4) required and recommended techniques to enhance this marking.

Characteristics. The runway threshold bar marking is 10 feet (3.1 m) in (5) width and extends between the runway edges or between the runway edge markings.

b. Arrow Marking. The arrow marking (arrowheads with and without arrow shafts) performs three possible functions, that is, two cases for displaced thresholds and one case for a runway threshold with an aligned taxiway.

Purposes. (1)

(i) Figure A-8 illustrates the predominant case in which the threshold is displaced from the runway end. In this case white arrowheads with and without arrow shafts are required to identify the portion of the runway before the displaced threshold to provide centerline guidance for pilots during approaches, takeoffs, and landing rollouts from the opposite direction.

c. Runway Demarcation Bar Marking. › (3) Location.

(ii) Figure A-10 illustrates the rare case in which a displaced threshold is preceded by an aligned taxiway. In this case white arrowheads with and without arrow shafts and yellow arrowheads without arrow shafts are required to identify the runway portion from the aligned taxiway portion. Furthermore, a yellow runway demarcation bar is required to identify the start of the runway. See paragraph 2.9.c for runway demarcation bar criteria.

(iii) Figure A-8 illustrates the rare case in which a runway threshold is preceded by an aligned taxiway. In this case yellow arrowheads without arrow shafts are required to identify the runway portion from the aligned taxiway portion.

General Comment The conversion of a runway section into an aligned taxiway or the construction of a new aligned taxiway is prohibited. See AC 150/5300-13.

Requirement. Install this marking when the threshold is displaced or (2) preceded by an aligned taxiway.

Locations. (3)

(i) For the predominant case, arrow shafts and arrowheads are located on the portion of the runway before the displaced threshold.

(ii) For the rare cases, only arrowheads are used on the portion of the aligned taxiway before the threshold bar marking or the demarcation bar marking.

Colors. (4)

(i) For the predominant case, the arrow shaft and arrowhead are white. See paragraph 1.4 for required and recommended techniques to enhance these markings.

(ii) For the rare cases, the arrowhead is yellow.

Characteristics. The dimensions and spacing requirements for arrow shafts (5) and arrowheads are as shown in Figure A-8 (function one), Figure A-8 (function two), and Figure A-10 (function three).

c. Runway Demarcation Bar Marking.

Purpose. A demarcation bar delineates a runway with a displaced (1) threshold from a blast pad, stopway, or an aligned taxiway that precedes the runway.

Requirement. Install a demarcation bar marking when the threshold is (2) displaced or preceded by a blast pad, stopway, or aligned taxiway.

Location. The demarcation bar is an elongated rectangular bar on a blast (3) pad, stopway, or an aligned taxiway that is perpendicular to the runway centerline at the point of intersection with the start of the runway as shown in Figure A-11. In another application, as

shown in Figure A-10, the portion of aligned taxiway before the demarcation bar is not part of the usable runway.

2.11. Runway shoulder marking. › c. Location. The runway shoulder marking is located between the runway…

Color. The demarcation bar marking is yellow. See paragraph 1.4 for (4) required and recommended techniques to enhance this marking.

Characteristics. The demarcation bar marking is 3 feet (0.9 m) wide and (5) extends across the entire width of the blast pad, stopway, or aligned taxiway.

2.10. Chevron markings for blast pads, stopways, and EMAS.

a. Purposes. The chevron marking identifies paved blast pads, stopways, and EMAS (engineered materials arresting systems) in relation to the end of the runway. For lighting provisions, see AC 150/5340-30, and for EMAS design, see AC 150/5220-22, Engineered Materials Arresting Systems (EMAS) for Aircraft Overruns.

b. Requirement. Install chevron markings on blast pads, stopways, and EMAS.

c. Location. The chevron marking is located on the blast pad and stopway that are aligned with and contiguous to the runway end as shown in Figure A-9 and Figure A-11. The chevron scheme for an EMAS installation is also centered along the extended runway centerline (not shown in Figure A-9 and Figure A-11.

d. Color. Chevron markings are yellow. See paragraph 1.4 for required and recommended techniques to enhance this marking.

e. Characteristics. Dimensionally, stopways equal the width of the runway while blast pads equal the runway width plus the shoulder widths (see AC 150/5300-13). The dimensions and spacing requirements for chevron markings are shown in Figure A-9. The recommended minimum length for a stopway is 150 feet (45.7 m) to allow for at least two chevron stripes. For cases where (1) standard length blast pads, per AC 150/5300-13, are installed off runway ends designed exclusively for small airplanes (Airplane Design Groups I and II– small) or (2) existing stopways are less than 150 feet (45.7 m) in length on runway widths of 75 feet (22.9 m) or less, the width of the chevrons and the spacing between the chevrons shown in Figure A-9 can be reduced by two-thirds. The intent of the reduction in dimensions is to provide pilots with at least two visible chevrons.

2.11. Runway shoulder marking.

a. Purpose. The runway shoulder marking is used, when needed, as a supplement to further delineate a paved runway shoulder that pilots have mistaken or are likely to mistake as usable runway. This marking is used only in conjunction with the runway edge marking.

b. Requirement. Runway shoulder markings are optional.

c. Location. The runway shoulder marking is located between the runway edge marking and the outer edge of the paved shoulder as shown in Figure A-12.

2.11. Runway shoulder marking. › e. Characteristics. The runway shoulder marking consists of stripes 3…

d. Color. Runway shoulder markings are yellow. See paragraph 1.4 for required and recommended techniques to enhance this marking.

e. Characteristics. The runway shoulder marking consists of stripes 3 feet (0.9 m) in width and spaced 100 feet (30.5 m) apart along the edge of the runway. The stripes start at the runway midpoint, are slanted at an angle of 45 degrees to the runway centerline, and are oriented as shown in Figure A-12.

3.2. Case 1 and Case 2 – Applications of Pattern A for the runway… › a. Purpose. Pattern A, when painted on a runway as shown in Figure…

Chapter 3. Holding Position Markings.

3.1. Applications of holding position markings.

The purposes for the different holding position markings are to prevent aircraft and vehicles from entering into critical areas associated with a runway and navigational aids or to control traffic at the intersection of taxiways. This advisory circular describes six operational situations (cases) using three different holding position marking schemes. Cases 1, 2, and 3 employ the same marking scheme referred to as Pattern A – runway holding position marking. Cases 4 and 5 employ a different marking scheme referred to as Pattern B – ILS/MLS or POFZ holding position marking. The latter operational situation, Case 5, uses Pattern B in which it usually appears as an L-shaped ladder. Case 6 uses a different marking scheme referred to as Pattern C – intermediate holding position marking for taxiway/taxiway intersections. Figure A-13 and Figure A-14 show the four different marking patterns.

 Case 1: In terms of taxiing on a runway, an aircraft will need to hold short of an

intersecting runway (see paragraph 3.2).

 Case 2: In terms of landing on a runway used for land and hold short operations

(LAHSO), the aircraft will need to hold short of an intersecting runway or, in some rare cases, at a specified hold spot on the landing runway (see paragraph 3.2).

 Case 3 (most common application for Cases 1, 2, and 3): In terms of taxiing on a taxiway,

an aircraft will need to hold short prior to entering an active runway (see paragraph 3.3).

 Case 4: In terms of taxiing on a taxiway, an aircraft will need to hold short before

entering the critical area of an Instrument Landing System (ILS)/Microwave Landing System (MLS) (see paragraph 3.4).

 Case 5: In terms of taxiing on a taxiway, an aircraft will need to hold short before

entering the critical area of a Precision Obstacle Free Zone (POFZ) (see paragraph 3.5). Although the surface marking pattern is the same as Case 4, the pattern in many applications is L-shaped, instead of only linear in shape.

 Case 6: In terms of taxiing on a taxiway, an aircraft will need to hold short of a

taxiway/taxiway intersection (see paragraph 3.6).

3.2. Case 1 and Case 2 – Applications of Pattern A for the runway holding position marking on runways.

a. Purpose. Pattern A, when painted on a runway as shown in Figure A-13, identifies the location where a pilot (or vehicle driver) is to stop and hold when (1) the runway is operationally closed for an interval of time so that ATCT can control taxiing operations through a runway/runway intersection or (2) the runway is used for land and hold short operations (LAHSO). For necessary corresponding signage and lighting provisions, see AC 150/5340-18, Standards for Airport Sign Systems, and AC 150/5340-30.

(2) Runways Used for LAHSO. › (ii) Certain airfield geometries for runways that are used for taxiing…

Safety Initiatives

(Safety) Note 1: Land and hold short operations (LAHSO) require a letter of agreement between the airport operator and the airport traffic control tower (ATCT). Note 2: Since the design standard for a full-length parallel taxiway reduces both wrong-runway takeoffs and runway incursions, we do not recommend the use of an operationally closed runway as a taxiway, especially when a parallel taxiway exists. Such an operation can potentially confuse pilots because this taxiing operation introduces yellow-colored taxiway surface markings onto the runway itself. Hence, to avoid the potential for operational errors by pilots, the airport operator should take measures to meet the full-length parallel taxiway design standard. In some cases, the operational capacity for a given runway could indicate the need for dual parallel taxiways to avoid this type of taxiing operation. Note 3: To avoid a runway incursion event at runway/runway intersections when an operationally closed runway is used as a taxiway, the intersection must have the runway holding position marking and corresponding signs whether or not pilots taxi through the runway/runway intersection. Additionally, this marking should only be used in those instances where documentation supports the need for the operational use of the runway as a taxiway. The operational use of a runway as a taxiway must be described in a Letter of Agreement with the ATCT.

b. Location. In all Case 1 and Case 2 applications, the criteria given below assume that the centerlines of the intersecting runways are perpendicular. Hence, for runway/runway intersections that are non-perpendicular, additional distance may be required to ensure that all airplane features, such as wingtips, remain outside the protected area of the intersecting runway.

Operationally Closed Runways Used for Taxiing Operations. The location (1) of the runway holding position marking on operationally closed runway is in accordance with the holdline criteria per AC 150/5300-13 for the intersecting runway’s runway design code.

Runways Used for LAHSO. (2)

(i) The location of the runway holding position marking on the runway used for LAHSO is in accordance with the holdline criteria per AC 150/5300-13 for the intersecting runway’s runway design code. On rare cases the location of the runway holding position marking for LAHSO is based on a predetermined hold-short point along the landing runway to protect an approach/departure flight path or to overcome painting difficulties as described below in paragraph 3.2.b(2)(ii). In no case should the location of the predetermined hold-short point be within the holdline criteria per AC 150/5300-13 for the intersecting runway’s runway design code.

(ii) Certain airfield geometries for runways that are used for taxiing or LAHSO operations have intersecting taxiway(s) that hamper the painting of the runway holding position marking (and installation of accompanying necessary signage) in accordance with the applicable holdline criterion. One such geometry occurs when a crossing taxiway or its fillet

3.3. Case 3 – Applications of Pattern A for the runway holding position… › a. Purposes. Pattern A, when painted on a taxiway as shown in Figure…

intersects the runway where the marking or sign is to be placed. One solution is to move the hold-short point farther away from the runway/runway intersection so that both the marking and the installed signage clear the common crossing area. Under this solution (1) the marking is always painted at a greater distance than the holdline criteria in AC 150/5300-13, and (2) the required corresponding signage retains only the runway designations, i.e., never uses a taxiway designation.

c. Color. The Pattern A marking scheme, as shown in Figure A-13, is yellow and, when painted on light-colored pavements, is outlined in black. See paragraph 1.4 and Table 1-1 for required and recommended techniques to enhance this surface marking on light-colored pavements.

d. Characteristics.

The marking is identical to the runway holding position marking installed (1) on a taxiway as described in paragraph 3.3 and shown in Figure A-13. The solid lines, as compared to the dashed lines, are always on the side where the aircraft is to hold.

The marking is installed perpendicular to the runway centerline and (2) interrupts all runway markings except for the runway designation marking. If the runway holding position marking should interrupt the mentioned exceptions, then paint the runway holding position marking farther away than specified by AC 150/5300-13 to avoid any interruption of these specified markings. The painting practice is to avoid “over striping” existing runway surface markings.

The runway holding position marking extends across the full width of the (3) runway but not onto the runway shoulders or onto any intersecting taxiway fillet.

3.3. Case 3 – Applications of Pattern A for the runway holding position marking on taxiways.

a. Purposes. Pattern A, when painted on a taxiway as shown in Figure A-13, serves several roles. For a taxiway that intersects a runway at an airport with an operating airport traffic control tower (ATCT), the Pattern A marking scheme identifies the location on a taxiway where pilots and vehicle drivers are to stop until they receive a clearance from ATCT to proceed onto the runway. Under this role, Pattern A may be supplemented with the Geographic Position Marking as part of the airport’s Surface Movement Guidance Control System (SMGCS) Plan as described in paragraph 4.11 and as shown in Figure D-8. For a taxiway that intersects a runway at an airport without an operating airport traffic control tower, Pattern A identifies the location where a pilot and vehicle drivers are to stop to ensure that they have adequate separation with other aircraft before proceeding onto the runway. For a taxiway that does not intersect a runway but crosses through a runway approach area or the runway safety area, the Pattern A marking scheme identifies the location on a taxiway where pilots and vehicle drivers are to stop to receive clearance from the airport traffic control tower before proceeding through the protected area. This application serves to stop a taxiing aircraft from penetrating the runway safety area (a runway incursion) or any of several airspace surfaces, for example, those used to define the runway threshold, runway inner approach obstacle free zone, or the runway inner transitional

3.3. Case 3 – Applications of Pattern A for the runway holding position… › d. Characteristics.

obstacle free zone. If the marking is located closer than prescribed by AC 150/5300-13, such as when the taxiing aircraft penetrates a Terminal Instrument Procedures (TERPS) surface, then the airport operator can expect higher approach minimums to the impacted runway end. AC 150/5300-13 includes a discussion of these airspace surfaces. Except as specified in paragraph 3.2, the runway holding position marking must not be used for any other situations than the roles described in this paragraph. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

b. Location. Pattern A for the runway holding position marking is located as follows:

For a taxiway that intersects a runway, the Pattern A runway holding (1) position markings must be located on all such taxiways in accordance with the holdline criteria per AC 150/5300-13 for the runway’s runway design code. This measurement is taken to the edge of the holding position marking farthest from the runway, at the taxiway centerline. Because the location is based on the approach visibility minimums, approach category, and airplane design group, the airport operator should use the lowest approach visibility minima and critical aircraft intended to use the runway. Pattern A is used also on turnarounds and holding bays as shown in AC 150/5300-13, especially for airports with an airport traffic control tower or for any runways used at night and in low-visibility conditions. Locating a runway holding position marking other than what is required by this paragraph must be approved by the FAA.

For a taxiway not intersecting a runway but crossing through a runway (2) safety area or a runway approach surface, the Pattern A runway holding position markings must be located on all such taxiways in accordance with the more protective area obtained by either the holdline criteria per AC 150/5300-13 for the runway’s runway design code or the boundary of the approach surface’s critical area. Locating a Pattern A runway holding position marking other than what is required by this paragraph must be approved by the FAA Airports Regional Office or Airports District Office.

14 Code of Federal Regulation (CFR) Part 139 Certificated Airports Runway Incursion Mitigation Requirement

(Safety) The extended runway holding position marking, as illustrated in Figure D-4, is mandatory and is the only acceptable means of compliance for 14 CFR Part 139 certificated airports serving ADGs V and VI airplanes. The enhanced runway holding position marking applies only to those taxiway entrances for a given runway that serve these airplane design groups. This surface painted marking is part of the taxiway centerline marking standard under 14 CFR Section 139.311(a)(2).

c. Color. The Pattern A marking scheme, as shown in Figure A-13, is yellow and, when painted on light-colored pavements, outlined in black. See paragraph 1.4 and Table 1-1 for required and recommended techniques to enhance this surface marking.

d. Characteristics.

d. Characteristics. › (5) Pattern A is painted perpendicular to the taxiway centerline but…

Pattern A for the runway holding position marking consists of a set of two (1) continuous lines, two dashed lines, and three spaces that are all parallel, extend across the entire width of the taxiway, measure 12 inches (30 cm) in width, and are separated as shown in Figure A-13. It is located laterally such that a dash is centered on the taxiway centerline. Where the marking extends unbroken over more than one taxiway centerline, locate the marking such that a dash is centered on one taxiway centerline. At airports that do not have an operating ATCT and are not certificated under 14 CFR Part 139, the width and separation measurement may be reduced from 12 inches (30 cm) to 6 inches (15 cm). For clarification, all airports certificated under 14 CFR Part 139, whether or not there is an operating ATCT, are required to use the 12inch measurement.

The taxiway centerline marking is interrupted by the runway holding (2) position marking as shown in Figure A-13.

For taxiways having taxiway edge markings, interrupt the taxiway edge (3) marking as shown in Figure A-23 so that the Pattern A marking continues to the edge of the defined taxiway width. For taxiways that connect to runways that serve Airplane Design Groups (ADG) V or VI airplanes as defined by AC 150/5300-13, the marking is further extended onto both paved shoulders as shown in Figure D-4. For both airplane design groups, the length of the marking from the taxiway centerline onto the paved shoulder measures 62.5 feet (19 m). The 62.5-foot (19-m) measurement takes into account the downward viewing angle from the cockpit while the pilots are seated in the normal position as well as other safety factors, such as aircraft wander from the taxiway centerline. For taxiways with widths greater than 75 feet (22.9 m), the runway holding position marking is extended 25 feet (7.5 m) [62.5 viewing angle minus (1/2)(75) standard taxiway width equals 25 feet] onto the paved taxiway shoulders. Only those taxiway entrances to runways that serve ADGs V or VI are to be further enhanced. Typical airplane models within ADGs V and VI include the Airbus 330-200/-300, A-340-200/-300/-500/- 600, A-380, Boeing-747-100/-200/-400, B-777-200/-300, and B-787-8/-9.

(i) If the runway holding position marking is outlined in black, then the taxiway edge markings abut the black outline on both sides of this marking. That is, it abuts the black border of the solid yellow line on one side and abuts the black border of the dashed yellow line on the other side (see Figure A-13).

(ii) If the runway holding position marking is not outlined in black, then the taxiway edge markings abut the holding position marking on both sides. That is, the taxiway edge markings abut the solid yellow line on one side and abut the dashed yellow line on the other side.

The orientation of Pattern A is for the solid continuous lines to be painted (4) on the side where the aircraft and vehicles will hold before proceeding to the runway. That is, dashed lines are painted closer to the runway.

Pattern A is painted perpendicular to the taxiway centerline but may be (5) canted from the perpendicular in unusual situations, such as an extremely acute, angled taxiway. For such unusual situations, it may be necessary to install additional runway holding position

b. Location. Pattern B for the ILS/MLS holding position marking is… › (2) If a taxiway or holding bay penetrates both an ILS/MLS critical…

signs, runway guard lights, or stop bars to emphasize the location of the surface painted runway holding position marking.

Pattern A on converging taxiways, as shown in Figure D-13, meet at an (6) angle when two or more taxiways intersect the same runway hold line. On any angled taxiway to the runway, consideration must be given to locate the painted marking so no portion of an aircraft, e.g., wing tip or tail, penetrates the runway safety area or any protected surface. See AC 150/5300-13 for detailed requirements and information about clearance requirements by aircraft on taxi routes.

For taxiways connecting to runways serving ADGs V and VI, having a (7) light fixture or a sign located on the taxiway shoulder that aligns with the extended runway holding position marking, as shown in Figure D-4, the extended runway holding position marking should extend no closer than 5 feet (1.5 m) to the edge of the light fixture or sign.

For taxiways connecting to runways serving ADGs V and VI whose (8) taxiway shoulder markings interfere with or are within 10 feet (3.1 m) from the extended runway holding position marking, as shown in Figure D-4, the taxiway shoulder markings are to be removed (omitted) from that location.

3.4. Case 4 – Applications of Pattern B for the ILS/MLS holding position marking.

a. Purposes. Pattern B for the ILS/MLS holding position marking as shown in Figure A-13 identifies the location on a taxiway or holding bay where a pilot or vehicle driver is to stop when they have received instructions from the airport traffic control tower (ATCT) to hold before entering an ILS/MLS critical area. The intent of the marking is to protect the signal of the ILS/MLS navigational aid by identifying the holding position for CAT I operations and protecting the approved TERPS for CAT II/III operations. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

b. Location. Pattern B for the ILS/MLS holding position marking is located on the taxiway or holding bay at the boundary of the ILS/MLS critical area and, as appropriate, at the holding position for CAT I and CAT II/III operations. The entire marking is located inside the boundary of the protected area.

Where the distance between the runway holding position marking (Pattern (1) A) on a taxiway and the holding position marking (Pattern B) for an ILS (or MLS) critical area is 50 feet (15 m) or less, one holding position may be established, provided it will not affect capacity. In this case, the runway holding position (Pattern A) is moved back to the ILS/MLS holding position (Pattern B) and only the runway holding position markings (Pattern A) are installed.

If a taxiway or holding bay penetrates both an ILS/MLS critical area and (2) the Precision Obstacle Free Zone (POFZ) critical area (see Pattern B, Figure A-13), such as when the threshold is displaced, paint only one pattern instead of two patterns only if the single pattern can protect both critical areas. The pattern to be painted is the one whose location offers the most conservative, protective boundary (for example, farthest from the runway).

(3) For taxiways having taxiway edge markings, interrupt the taxiway… › (i) If the ILS/MLS holding position marking is outlined in black, then…

The FAA will designate the ILS/MLS critical area and POFZ boundaries (3) and, as appropriate, determine the correct holding position location for CAT II/III operations for the airport operator. See AC 150/5300-13 for general information about the ILS/MLS and POFZ critical areas.

c. Color. The Pattern B marking scheme as shown in Figure A-13 is yellow and, when used on light-colored pavements, outlined in black. See paragraph 1.4 and Table 1-1 for required and recommended techniques to enhance this surface marking.

d. Characteristics.

Pattern B for the ILS/MLS holding position marking consists of a set of (1) two parallel lines that are 2 feet (0.6 m) wide and spaced 4 feet (1.2 m) apart. These parallel lines are connected by perpendicular sets of two lines that are 1 foot (0.3 m) wide and spaced 1 foot (0.3 m) apart and repeat every 10 feet (3 m). The Pattern B marking for ILS/MLS applications must extend across the entire width of the taxiway or holding bay (see Figure A-13). It is located laterally such that a set of perpendicular lines (parallel to the taxiway centerline) are equidistant from the taxiway centerline. Where the marking extends unbroken over more than one taxiway centerline, locate the marking such that one set of perpendicular lines is equidistant from one taxiway centerline. At airports that do not have an ATCT and are not certificated under 14 CFR Part 139, the airport operator may reduce the dimension for the width of the parallel yellow lines and spaces from 2 feet (0.6 m) to 1 foot (0.3 m) and from 4 feet (1.2 m) to 2 feet (0.6 m). For clarification, all airports certificated under 14 CFR Part 139, whether or not there is an operating ATCT, are required to use the larger measurements.

The taxiway centerline marking is interrupted by the ILS/MLS holding (2) position marking as shown in Figure A-13.

For taxiways having taxiway edge markings, interrupt the taxiway edge (3) marking so that the Pattern B marking continues to the edge of the defined taxiway width as shown in Figure A-13. For taxiways that connect to runways that serve Airplane Design Groups (ADG) V or VI airplanes as defined by AC 150/5300-13, the marking is further extended onto both paved shoulders (similar to Pattern A as shown in Figure D-4) only when the Pattern A marking is omitted per paragraph 3.4.b(1). In that case, for both airplane design groups, the length of the marking from the taxiway centerline onto the paved shoulder measures 62.5 feet (19 m). The 62.5-foot (19-m) measurement takes into account the downward viewing angle from the cockpit while the pilots are seated in the normal position as well as other safety factors, such as aircraft wander from the taxiway centerline. For taxiways with widths greater than 75 feet (22.9 m), the ILS/MLS holding position marking is extended 25 feet (7.5 m) [62.5 viewing angle minus (1/2)(75) standard taxiway width equals 25 feet] onto the paved taxiway shoulders. Typical airplane models within ADGs V and VI include the Airbus 330-200/-300, A-340-200/- 300/-500/-600, A-380, Boeing-747-100/-200/-400, B-777-200/-300, and B-787-8/-9.

(i) If the ILS/MLS holding position marking is outlined in black, then the taxiway edge markings abut the black outline on both sides of this marking (see Figure A- 13).

(ii) If the ILS/MLS holding position marking is not outlined in black, a 6-inch gap is left between the holding position marking and the taxiway edge marking (see Figure A-13).

b. Location. Pattern B for the POFZ holding position marking is located… › (1) Certain airfield geometries may cause a taxiway or holding bay to…

Pattern B is painted perpendicular to the taxiway centerline but may be (4) canted from the perpendicular in unusual situations, such as an extremely acute, angled taxiway. For such unusual situations, it may be necessary to install additional runway holding position signs, runway guard lights, or stop bars to emphasize the location of the surface painted runway holding position marking.

Pattern B on converging taxiways meet at an angle when two or more (5) taxiways intersect the same ILS/MLS hold line. On any angled taxiway to the runway, consideration must be given to locate the painted marking so no portion of an aircraft, e.g., wing tip or tail, penetrates the protected surface. See AC 150/5300-13 for detailed requirements and information about clearance requirements by aircraft on taxi routes.

For taxiways connecting to runways serving ADGs V and VI whose (6) taxiway shoulder markings interfere with or are within 10 feet (3.1 m) from the extended ILS/MLS holding position marking (see paragraph 3.4.d(3)), the taxiway shoulder markings are to be removed (omitted) from that location.

3.5. Case 5 – Applications of Pattern B for Precision Obstacle Free Zone (POFZ) holding position marking.

a. Purposes. Pattern B for the POFZ holding position marking as shown in Figure A- 13 identifies the location on a taxiway or holding bay where a pilot or vehicle driver is to stop when they have received instructions from the airport traffic control tower (ATCT) to hold before entering the POFZ critical area. The marking is used also at non-towered airport where the runway end has an approved vertical guidance of ¾-statue mile approach visibility minimum or less. The intent of the marking is to protect the authorized landing minima (TERPS) for a given runway end. See AC 150/5300-13 for detailed information about the POFZ critical area. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30. Install this marking when a POFZ exists.

b. Location. Pattern B for the POFZ holding position marking is located on the taxiway or holding bay at the boundary of the POFZ critical area as defined by AC 150/5300-13 and, when appropriate, at the holding position for CAT I and CAT II/III operations. Figure A-17 shows the most common application for this marking, which is L-shaped. Because of the variety of taxiway entrance/holding bay geometries, the Pattern B marking must not be painted over a surface painted holding position sign.

Certain airfield geometries may cause a taxiway or holding bay to (1) penetrate both an ILS/MLS critical area and the Precision Obstacle Free Zone (POFZ) critical area, such as when the threshold is displaced. Under such situations, paint only one pattern instead of two patterns only if the single pattern can protect both critical areas. The pattern to be painted is the one whose location offers the most conservative, protective boundary (for example, farthest from the runway). Under this application the ILS/MLS holding position

3.6. Case 6 – Applications for Pattern C for the taxiway/taxiway… › b. Location. For the taxiway being marked, the intermediate holding…

(Pattern B) marking or POFZ holding position (Pattern B) marking, which now serves a dual function, cannot be replaced with, or used in lieu of, a runway holding position (Pattern A) marking.

The FAA Airports Regional Office or Airports District Office will (2) designate the ILS/MLS critical area and POFZ boundaries and, as appropriate, determine the correct holding position location for CAT II/III operations for the airport operator.

The Pattern B marking for POFZ applications must extend across only (3) those portions of a taxiway or holding bays that run along the boundary of the POFZ as shown in Figure A-14 and Figure A-17.

c. Color. The Pattern B marking scheme is yellow and, when used on light-colored pavements, outlined in black. See paragraph 1.4 and Table 1-1 for required and recommended techniques to enhance this surface marking.

d. Characteristics. Pattern B for the POFZ holding position marking consists of a set of two parallel lines that are 2 feet (0.6 m) wide and spaced 4 feet (1.2 m) apart. These parallel lines are connected by perpendicular sets of two lines that are 1 foot (0.3 m) wide and spaced 1 foot (0.3 m) apart and repeated every 10 feet (3 m). It is located laterally such that a set of perpendicular lines (parallel to the taxiway centerline) are equidistant from the taxiway centerline. Where the marking extends unbroken over more than one taxiway centerline, locate the marking such that one set of perpendicular lines is equidistant from one taxiway centerline. Figure A-13, provides the discontinuation (separation) of a POFZ holding position marking, which follows the same criteria as the ILS/MLS holding position marking, with an intersecting taxiway centerline or taxiway edge markings. Figure A-17 illustrates the general separation of a Pattern B marking from an entrance taxiway serving a runway. At airports that do not have an ATCT and are not certificated under 14 CFR Part 139, the airport operator may reduce the dimension for the width of the parallel yellow lines and spaces from 2 feet (0.6 m) to 1 foot (0.3 m) and from 4 feet (1.2 m) to 2 feet (0.6 m). For clarification, all airports certificated under 14 CFR Part 139, whether or not there is an operating ATCT, are required to use the larger measurements.

3.6. Case 6 – Applications for Pattern C for the taxiway/taxiway intersection intermediate holding position marking.

a. Purpose. Pattern C for the intermediate holding position marking, as shown in Figure A-13 for taxiway/taxiway intersections, is used to support the operational need by the airport traffic control tower to manage taxiing aircraft through a congested intersection or for other reasons deemed necessary by the FAA. For example, Figure A-15 shows the intersection between a taxiway and a holding pad used for deicing aircraft. Pilots when instructed by the airport traffic control tower to “hold short of (taxiway designation)” must stop so no part of the aircraft extends beyond the boundary of the intermediate holding position marking. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

b. Location. For the taxiway being marked, the intermediate holding position marking for taxiway/taxiway intersection is located according to the taxiway centerline to fixed

3.6. Case 6 – Applications for Pattern C for the taxiway/taxiway… › d. Characteristics. The intermediate holding position marking for…

or movable object criteria in AC 150/5300-13 for the most demanding airplane design group serving the airport (per the definition in AC 150/5300-13).

c. Color. The intermediate holding position marking is yellow and, when used on light-colored pavements, outlined in black. See paragraph 1.4 and Table 1-1 for required and recommended techniques to enhance this surface marking.

d. Characteristics. The intermediate holding position marking for taxiway/taxiway intersections consist of a single dashed line extending across the width of the taxiway per Figure A-14 and Figure C-7. The single dashed lines are 1 foot (0.3 m) wide, 3 feet (0.9 m) long, and spaced 3 feet (0.9 m) apart. The marking is located laterally such that a dash is centered on the taxiway centerline. Where the marking extends unbroken over more than one taxiway centerline, locate the marking such that a dash is centered on one taxiway centerline. As shown in Figure A- 14, all intersecting taxiway centerlines are spaced 6 to 12 inches (15 cm to 30 cm) on either side of this marking. When the taxiway has taxiway edge markings, the taxiway edge markings are interrupted.

Continue reading ↓ 120 of 257 passages shown