Radar Vectors
Advisory Circular Cancelled Issued Sep 3, 2010 AAS-100 122 pages Copy saved Nov 18, 2026

AC 150/5340-1K Standards for Airport Markings

Contains the FAA standards for markings used on airport runways, taxiways, and aprons. This AC cancels the Signs and Marking Supplement (SAMS). This document is consolidated to include Change 1, dated November 17, 2010.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Standards for Airport Markings

Date: 9/3/2010 Initiated by: AAS-100

AC No: 150/5340-1K Change:

1. PURPOSE. This advisory circular (AC) contains the Federal Aviation Administration (FAA) standards for markings used on airport runways, taxiways, and aprons. 2. CANCELLATION. This AC cancels AC 150/5340-1J, Standards for Airport Markings, dated April 29, 2005, and subsequent changes, dated March 31, 2008, and June 6, 2008. This AC also cancels the Signs and Marking Supplement (SAMS). 3. APPLICATION. The FAA recommends the guidelines and standards contained herein for the marking of airport runways, taxiways, and aprons. The use of these standards is the only method of compliance with the marking of runways, taxiways, and aprons for airports certificated under Title 14 Code of Federal Regulations Part 139, Certification of Airports (Part 139). These standards are to be used on all new airport projects that are under development and are to be implemented at all Part 139 certificated airports.

Further, use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and with revenue from the Passenger Facility Charge (PFC) Program. (See Grant Assurance No. 34, “Policies, Standards, and Specifications” and PFC Assurance No. 9, “Standards and Specifications. 4. NATIONAL TRANSPORTATION SAFETY BOARD SAFETY RECOMMENDATION. The National Transportation Safety Board (NTSB) in response to pilots landing on taxiways adjacent to runways, requested that the FAA conduct research and development to identify visual aid enhancement solutions for use with taxiways that experience repeated taxiway landing problems (reference: Item A-04- 49 of NTSB Safety Recommendation letter, dated June 25, 2004). a. Results. The FAA evaluated the non-standard surface markings requested by NTSB, namely an enlarged, reoriented surface paint “A” taxiway location sign, a serpentine marking running along the taxiway centerline, and the inscriptions “TAXIWAY” and “TAXI ONLY. The investigation determined that all proposals had some deficiencies.

For example, serpentine markings were found not to be significantly visible from the air. The smaller, length inscription “TAXI” by itself in the phrase “TAXI ONLY” was sufficient to perform the same intended task. See report DOT/FAA/AR-TN 07/54, Identification Techniques to Reduce Confusion Between Taxiways and Adjacent Runways, for details. See paragraph 5.16 of this advisory circular for the usage of the non-standard marking “TAXI.” b. Other Observations. The report further concluded “…that airport geometry is a major causal factor in such incidents …. One rectifying solution for troublesome airport geometry was the use of green-colored aviation grade artificial turf that would visually change the shape of the taxiway environment. One application is masking the squared paved corner of the entrance taxiway so that it creates the effect of a curved taxiway, i.e., minimize its visual size in comparison to the squared runway end. See paragraph 5.16 of this advisory circular for additional information. AC 150/5370-15, Airside

Consolidated AC includes Change 1

ii

Applications for Artificial Turf, latest edition, provides guidance for the use of aviation grade artificial turf in areas adjacent to the operational areas of the airport. This solution is not for runway environment applications because: “Sufficient data are not available on the performance of artificial turf in the case of high-speed veer offs...” (see paragraph 5 of AC 150/5370-15A). 5. EXPLANATION OF PRINCIPAL CHANGES. This AC incorporates new surface marking criteria, extensive text and format changes, and new and revised figures, as described below:

a. Adds color-coded text boxes to emphasize safety initiatives, solutions to painting difficulties, and general remarks.

 Green (Painting) – explains painting precautions and solutions, such as when

proportioning is permissible for runway surface markings.  Red (Safety) – emphasizes safety initiatives.  Gray (General) – contains general remarks. b. Incorporates all applicable surface marking supplements from SAMS. c. Adds new definitions (paragraph 1.2). d. Adds a new subparagraph, “Painted Numbering System for Record Keeping of Surface Painted Markings” (paragraph 1.3(f)). This practice was added to assist airport operators in identifying surface markings in their Sign Plan needing maintenance, scheduling painting, etc.

e. Adds new table 1-1 that provides general guidelines for determining when to add black borders to light-colored pavements (paragraph 1.4).

f. Adds a new warning box about dispensing glass beads during painting applications and, in particular, when painting surface painted holding position signs (paragraph 1.4(b)).

g. Revises table 2-1 criteria (paragraph 2.1). h. Deletes all text related to the former FAA threshold marking scheme. This revision adopts the standards and recommended practices contained in International Civil Aviation Organization (ICAO) Annex 14, Volume I, Aerodrome Design and Operations. Adds new table 2-2, which shows the number of symmetrical runway threshold stripes required for standard runway widths and new text for painting non-standard runway widths (paragraph 2.5(d)).

i. Adds new text to emphasize the co-located relationship between the aiming point marking and PAPI and other NAVAIDs (paragraphs 2.2 and 2.6).

j. Adds new criteria for the width of and separation between aiming point markings for various standard runway widths (paragraph 2.6(d)).

k. Adds new table 2-3 and new text for table 2-4 about painting touchdown zone markings for runway ends having single or dual precision approaches (paragraph 2.7).

l. Clarifies text for marking runways with and without aligned taxiways (paragraph 2.9).

iii

m. Adds Engineered Materials Arresting System (EMAS) to blast pads and stopways as facilities to be marked with chevrons (paragraph 2.10). Adds new painting criteria for stopways for Airplane Design Group I – exclusively small airplane runways (paragraph 2.10(d)).

n. Includes a new Chapter 3 that consolidates the six different applications of holding position markings and different painting schemes, with a new pattern designation, i.e., Pattern A, B, and C surface markings for holding positions. The pattern designation is more in line with the standards and recommended practices contained in ICAO Annex 14, Volume I.

o. Adds new and revised text for painting the enhanced taxiway centerline marking (paragraph 4.3). p. Adds new criteria for painting NO-TAXI islands with continuous taxiway edge markings for wide taxiway entrances (paragraph 4.4) as a means to reduce runway incursions.

q. Adds new criteria and revised text for surface painted holding position signs (paragraph 4.5). The new criteria apply to Airplane Design Groups I and II, requiring a single surface painted holding position sign centered on the taxiway centerline instead of a single surface painted holding position sign to the left of centerline or dual surface painted holding position signs (paragraph 4.5(b)(4) and new figure C-15).

r. Adds a new table 4-1, “Placement of Repetitive Surface Painted Holding Position Signs and NO-TAXI Islands on Taxiway Entrances of over 200 feet (61 m) in Width” (paragraph 4.5).

s. Adds new criteria for the minimum height of surface painted holding position signs for Airplane Design Groups III – VI and for Airplane Design Groups I – II (paragraph 4.5(d) and figures C-5, C-6, C-7, and C-8).

t. Adds a new green-colored box explaining when to stack surface painted holding position signs on narrow taxiways widths (paragraph 4.5(d) and new figure C-15).

u. Adds new and revised text about the geographic position marking (paragraph 4.11).

v. Drops a proposed new surface marking for areas designated by the Transportation Security Administration (TSA) and the airport operator as a security identification display area (SIDA) (reassigned paragraph 5.15 to cover markings for aircraft deicing facilities and removed proposed figure C-14). TSA accepted the task to address future markings for the airside.

w. Adds a new paragraph 5.15, “Aircraft Deicing Facility Markings,” to reference markings for aircraft deicing facilities in accordance with AC 150/5300-14, Design of Aircraft Deicing Facilities.

x. Adds new paragraph 5.16, Interim Surface Markings for Taxiways Mistaken as Runways, in response to NTSB Safety Letter.

y. Revises figures 1 and 2 to show only one threshold marking scheme (formerly referred to as Configuration B) and drops painting method Configuration A per paragraph 2.5. The single marking scheme conforms with ICAO Annex 14, Volume I.

z. Adds new text to figure 8 emphasizing that the width of a stopway only equals the runway width, but the width of a blast pad includes both the runway width and the shoulders.

iv

aa. Adds new figure 12a showing that the Pattern B application for POFZ holding position marking differs from the ILS/MLS holding position marking by turning 90 degrees on certain taxiway or holding bay geometries.

bb. Adds new figures C-2 and C-3 from SAMS.

cc. All figures in this advisory circular are full scale AutoCAD drawings saved as MS Word versions. For some figures, certain details may appear to be missing (missing or broken lines) when either printed or viewed on a computer monitor. To view all the details in these figures, use the appropriate ZOOM function provided in MS Word or Adobe Reader. In some instances, where there is a large surface area, a ZOOM value of over 250% may be necessary to view all details. Both this advisory circular and the original AutoCAD files for all figures are available for download at the FAA web site: http://www.faa.gov/airports/resources/advisory_circulars/index.cfm/go/document.list/parentTopicID/85. 6. COMPLIANCE DATES FOR SPECIFIC SURFACE PAINTED MARKINGS FOR 14 CODE OF FEDERAL REGULATION (CFR) PART 139 CERTIFICATED AIRPORTS. The compliance dates for the enhanced taxiway centerline marking and the surface painted holding position sign are found within the red-coded Safety Boxes in paragraphs 4.3(a) and 4.5(a), respectively. See these paragraphs for the applicable compliance dates. 7. METRIC UNITS. To promote an orderly transition to metric units, the text and figures include both English and metric dimensions. The metric conversions are based on operational significance and may not be exact equivalents of the English dimensions. Until there is an official changeover to the metric system, the English dimensions govern. 8. ADVISORY CIRCULAR (AC) AND ORDER REFERENCES. All references to FAA ACs and Orders are to the most recent versions, which are available from the FAA website at http://www.faa.gov. Michael J. O’Donnell Director of Airport Safety and Standards

TABLE OF CONTENTS

v

TABLE OF CONTENTS

CHAPTER 1. SURFACE MARKINGS FOR AIRFIELD PAVEMENTS AND PAVED AIRFIELD ROADWAYS … 1 1.1. GENERAL … 1 1.2. DEFINITIONS … 1 1.3. SURFACE MARKING PRACTICES … 2 1.4. REQUIREMENTS AND RECOMMENDATIONS FOR ENHANCED CONSPICUITY OF SURFACE MARKINGS … 3

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS … 7 2.1. APPLICATION … 7 2.2. INTERRUPTION OF RUNWAY SURFACE MARKINGS … 8 2.3. RUNWAY LANDING DESIGNATOR MARKING … 9 2.4. RUNWAY CENTERLINE MARKING … 11 2.5. RUNWAY THRESHOLD MARKING … 12 2.6. RUNWAY AIMING POINT MARKING … 13 2.7. RUNWAY TOUCHDOWN ZONE MARKING … 15 2.8. RUNWAY SIDE STRIPE MARKING … 18 2.9. RUNWAY DISPLACED THRESHOLD MARKING … 19 2.10. CHEVRON MARKINGS FOR BLAST PADS, STOPWAYS, AND EMAS … 21 2.11. RUNWAY SHOULDER MARKING … 21

CHAPTER 3. HOLDING POSITION MARKINGS … 23 3.1. APPLICATIONS OF HOLDING POSITION MARKINGS … 23 3.2. CASE 1 AND CASE 2 – APPLICATIONS OF PATTERN A FOR THE RUNWAY HOLDING POSITION MARKING ON RUNWAYS … 23 3.3. CASE 3 – APPLICATIONS OF PATTERN A FOR THE RUNWAY HOLDING POSITION MARKING ON TAXIWAYS … 25 3.4. CASE 4 – APPLICATIONS OF PATTERN B FOR THE ILS/MLS HOLDING POSITION MARKING … 27 3.5. CASE 5 – APPLICATIONS OF PATTERN B FOR PRECISION OBSTACLE FREE ZONE (POFZ) HOLDING POSITION MARKING … 28 3.6. CASE 6 – APPLICATIONS FOR PATTERN C FOR THE TAXIWAY/TAXIWAY INTERSECTION INTERMEDIATE HOLDING POSITION MARKING … 29

CHAPTER 4. SURFACE MARKINGS FOR TAXIWAYS … 31 4.1. APPLICATION … 31 4.2. TAXIWAY CENTERLINE MARKINGS … 31 4.3. ENHANCED TAXIWAY CENTERLINE MARKING … 33 4.4. TAXIWAY EDGE MARKING … 36 4.5. SURFACE PAINTED HOLDING POSITION SIGNS … 38 4.6. SURFACE PAINTED TAXIWAY DIRECTION SIGNS … 43 4.7. SURFACE PAINTED TAXIWAY LOCATION SIGNS … 44 4.8. SURFACE PAINTED GATE DESTINATION SIGNS … 45 4.9. SURFACE PAINTED APRON ENTRANCE POINT SIGNS … 46 4.10. TAXIWAY SHOULDER MARKINGS … 47 4.11. GEOGRAPHIC POSITION MARKINGS … 47

vi

CHAPTER 5. OTHER SURFACE MARKINGS … 51 5.1. APPLICATION … 51 5.2. VEHICLE ROADWAY MARKINGS … 51 5.3. VERY HIGH FREQUENCY OMNIDIRECTIONAL RANGE (VOR) RECEIVER CHECKPOINT MARKING … 51 5.4. NON-MOVEMENT AREA BOUNDARY MARKING … 52 5.5. MARKINGS FOR THRESHOLDS TEMPORARILY RELOCATED DURING CONSTRUCTION … 54 5.6. MARKING AND LIGHTING OF PERMANENTLY CLOSED RUNWAYS AND TAXIWAYS … 54 5.7. TEMPORARILY CLOSED RUNWAYS AND TAXIWAYS … 54 5.8. CONVERTING A RUNWAY TO A TAXIWAY … 55 5.9. INTERMITTENT USE OF A TAXIWAY AS A RUNWAY … 56 5.10. CLOSED OR ABANDONED AIRPORTS … 57 5.11. HELIPORT MARKINGS … 57 5.12. VERTIPORT MARKINGS … 57 5.13. MARKING FOR ARRESTING GEAR … 57 5.14. HAZARDOUS CONSTRUCTION AREAS … 57 5.15. AIRCRAFT DEICING FACILITY MARKINGS … 57 5.16. INTERIM SURFACE MARKINGS FOR TAXIWAYS MISTAKEN AS RUNWAYS … 57

APPENDIX A. INSCRIPTIONS FOR SIGNS AND GEOGRAPHIC POSITION

MARKINGS … 87

APPENDIX B. EXAMPLES OF MARKINGS OUTLINED IN BLACK … 93

APPENDIX C. ENHANCED MARKINGS FOR RUNWAY HOLDING POSITION … 97 1. GENERAL … 97 2. APPLICABILITY … 97 3. ENHANCED TAXIWAY CENTERLINE MARKINGS … 98 4. ENHANCED RUNWAY HOLDING POSITION MARKINGS … 101 5. SURFACE PAINTED HOLDING POSITION SIGNS … 102 6. ADDITIONAL GUIDELINES FOR APPLICATION … 106

FIGURES

Figure 1-1. Example of DFW Painted Numbering System for Surface Painted Markings … 3 Figure 5-1. Precautionary Placement of Non-movement Boundary Marking … 53 Figure 5-2. TAXI Marking Location Facing Runway Approach End … 58 Figure 5-3. TAXI Marking Dimensions … 59 Figure 5-4. Aviation Grade Artificial Turf Installation … 59 Figure 1. Precision Runway Markings … 61 Figure 2. Non-precision Runway … 62 Figure 3. Visual Runway Markings … 63 Figure 4. Example of Conflicting Markings on Crossing Runways … 64 Figure 5. Runway Designation Numerals and Letters … 65 Figure 6. Displaced Threshold Markings … 66 Figure 7. Marking for Aligned Taxiway with Runway Without a Displaced Threshold … 67 Figure 8. Markings for Blast Pads and Stopways … 68 Figure 9. Markings for Aligned Taxiway Preceding a Displaced Threshold … 69 Figure 10. Markings for Blast Pad Preceding a Displaced Threshold … 70

vii

Figure 1-1: picture of page 6Figure 1-1 · page 6
Picture of the page from the copy saved here

Figure 11. Runway Shoulder Markings … 71 Figure 12. Holding Position Marking Details … 72 Figure 12a. Holding Position Marking Details … 73 Figure 13. Taxiway Markings … 74 Figure 14. Taxiway Markings … 75 Figure 15. Taxiway Markings … 76 Figure 16. Methods for Taxiway Centerline Marking … 77 Figure 17. Surface Painted Signs … 78 Figure 18. Surface Painted Gate Identification Signs … 79 Figure 19. Multiple Gate Signs … 80 Figure 20. Surface Painted Apron Entrance Point Signs … 81 Figure 21. Taxiway Shoulder Markings … 82 Figure 22. Geographic Position Markings … 83 Figure 23. Vehicle Roadway Markings … 84 Figure 24. VOR Receiver Checkpoint Markings … 85 Figure 25. Closed Runway and Taxiway Markings … 86 Figure A - 1. Pavement Markings ABCDEFGH … 87 Figure A - 2. Pavement Markings IJKLMNOP … 88 Figure A - 3. Pavement Markings QRSTUVWX … 89 Figure A - 4. Pavement Markings YZ123456 … 90 Figure A - 5. Pavement Markings 7890-, … 91

Figure 11: picture of page 7Figure 11 · page 7
Picture of the page from the copy saved here

Figure B - 1. Runway Holding Position Marking … 93 Figure B - 2. ILS/MLS Holding Position Marking … 93 Figure B - 3. Continuous Taxiway Edge Line Marking … 94 Figure B - 4. Dashed Taxiway Edge Line Marking … 94 Figure B - 5. Alternate Outlining Method for Dashed Taxiway Edge Line Marking … 94 Figure B - 6. Taxiway Centerline Marking … 94 Figure B - 7. Intermediate Holding Position Markings … 95 Figure B - 8. Non-movement Area Boundary Marking … 95 Figure C - 1. Enhanced Taxiway Centerline Markings … 98 Figure C - 2. Dashed Lines at Converging Taxiway Centerlines … 98 Figure C - 3. Converging, Straight, and Curved Enhanced Taxiway Centerlines Intersecting with

Holding Position Marking … 99 Figure C - 4. Enhanced Runway Holding Position Markings on Taxiways … 101 Figure C - 5. Surface Painted Holding Position Signs For Taxiway Widths Greater Than 35 Feet

(10.5 m) … 102 Figure C - 6. Surface Painted Holding Position Sign for Taxiway Widths Equal to Or Less Than 35

Feet (10.5 m) … 103 Figure C - 7. Surface Painted Holding Position Signs when Taxiway Centerline is not Perpendicular

to Runway Holding Position Marking … 104 Figure C - 8. Surface Painted Holding Position Signs Co-Located with Geographic Position Marking . 105 Figure C - 9. Two Taxiway Centerlines Converging at a Runway Holding Position Marking … 106 Figure C - 10. Intersection of Two Taxiways at Runway End … 107 Figure C - 11. Intersection of Three Converging Taxiway Centerlines … 108 Figure C - 12. Intersection of Multi-Taxiway Centerlines with Less than 150 Feet (45.7 m) Between

Taxiways … 109 Figure C - 13. Two Taxiway Centerlines Intersecting a Runway Holding Position Marking … 110

viii

Figure C - 14. Intersection of Stub Taxiway and Runway … 111 Figure C - 15. Narrow Taxiway Stacked Surface Painted Holding Position Sign … 112 Figure C - 16. Enhanced Taxiway Centerlines When a Taxiway Connects Closely Spaced Runways ... 113

TABLES

Table 1-1. General Guidelines for Determining Light-Colored Pavements … 3 Table 2-1. Minimum Required Runway Surface Marking Schemes for Paved Runways … 7 Table 2-2. Number of Runway Threshold Stripes for Standard Runway Widths … 13 Table 2-3. Pairs of Touchdown Zone Markings Required When Installed From One Threshold … 16 Table 2-4. Pairs of Touchdown Zone Markings Required When Installed From Both Thresholds … 17 Table 4-1. Placement of Repetitive Surface Painted Holding Position Signs and NO-TAXI Islands on

Taxiway Entrances of over 200 feet (61 m) in Width … 41

CHAPTER 1. › 1.2. DEFINITIONS.

CHAPTER 1. SURFACE MARKINGS FOR AIRFIELD PAVEMENTS AND PAVED

AIRFIELD ROADWAYS.

1.1. GENERAL. This chapter provides the standards for surface markings used on paved airfield pavements (runways, taxiways, aprons) and paved airfield roadways. The standards for the surface markings assume that runways, taxiways, and aprons are built in accordance to the standard dimensions and layouts (e.g., clearances, fillets) in Advisory Circular (AC) 150/5300-13, Airport Design. The airport operator should expect difficulties when painting surface markings on non-standard infrastructure, such as a runway with a non-standard width. To assist airport operators, this advisory circular offers a few workable solutions for existing non-standard situations. Surface markings for large airplane parking positions and surface markings for unpaved airfield runways will be addressed at a future date in additional chapters. NOTE: All figures in this AC are reduced versions of DWG files compatible with MS Word. Use the zoom feature in MS Word or Adobe Reader to view detail in any figure. 1.2. DEFINITIONS. The following definitions apply to terms used in this AC.

a. Certificated Airport. An airport that has been issued an Airport Operating Certificate by the FAA under the authority of 14 CFR Part 139, Certification of Airports.

b. Commercial Service Airports and Passenger Enplanements. Defined in FAA Order 5100.38, Airport Improvement Program Handbook. c. Displaced Threshold. A threshold that is located at a point on the runway other than the designated beginning of the runway.

d. Movement Area. The runways, taxiways, and other areas of an airport that are used for taxiing, takeoff, and landing of aircraft, exclusive of loading ramps and aircraft parking areas (reference 14 CFR Part 139). e. Non-precision Runway. A runway end having an instrument approach procedure that provides course guidance without vertical path guidance. See Appendix 16, New Instrument Approach Procedures, in AC 150/5300-13, Airport Design, for additional information.

f. Precision Runway. A runway end having an instrument approach procedure that provides course and vertical path guidance conforming to Instrument Landing System (ILS) or Microwave Landing System (MLS) precision approach standards in International Civil Aviation Organization (ICAO) Annex 10, Compliance Statement, Aeronautical Telecommunications. See AC 150/5300-13 for additional information about precision approaches. g. Threshold. The beginning of that portion of the runway that is available for landing. In some instances, the landing threshold may not coincide with the end of the opposite direction runway (see “Displaced Threshold”).

h. Visual Runway. A runway end without an existing or planned (on the Airport Layout Plan) straight-in instrument approach procedure.

CHAPTER 1. › 1.3. SURFACE MARKING PRACTICES.

1.3. SURFACE MARKING PRACTICES. The following subparagraphs address common practices used in airport markings.

a. Increasing the Friction Coefficient of Surface Markings. AC 150/5370-10, Standards for Specifying Construction of Airports, Item P-620, Runway and Taxiway Painting, provides airport operators information to increase the friction coefficient of surface markings. Common practices include the spreading of silica sand on the marked surface immediately after painting and the use of glass beads in the marking materials. Glass beads or silica sand are required when durable markings (epoxy and methylacrylate based paints) are used. These paints are usually applied at 18 – 30 mils in dry thickness.

b. Paint Color Specifications, Requirements for Surface Preparation, Paint Application Rates and Methods, and Requirements for Preformed Thermal Plastic Markings. AC 150/5370-10 provides the paint color specifications, requirements for surface preparation, paint application rates, the various methods for applying paint, and the performance requirements for using only preformed thermoplastic markings. Precaution: Reflective tapes such as those commonly used for highways and city street applications are not to be used on the airside because of the potential for foreign object damage caused by loosened painted tape.

c. Striated Markings. Striated markings, which may be used in areas subject to frost heave, consist of painted stripes 4 inches (10 cm) to 8 inches (20 cm) in width that are separated by unpainted stripes. The width of the unpainted stripe may not exceed the width of the painted stripe. The width of the painted and unpainted stripes must be the same throughout the specific marking. Each edge of the marking must be a painted stripe. That is, a painted stripe is to begin and end within the width of the markings. Precaution: Because striated markings offer reduced visibility compared to non-striated markings, more frequent maintenance is required to maintain an acceptable level of visibility. Hence, striated markings are never used on Category II and Category III runways.

d. Temporary Markings. When selecting a material for temporary markings, consider the difficulty of removing the temporary marking when it is no longer needed. Some airports have had some success using water-based paint. Striated markings may also be used for temporary markings, but they are never used to denote a closed runway or other closed pavement or for Category II or Category III runways.

e. Removal of Markings. Pavement markings that are no longer needed are not to be painted over but instead are to be physically removed. Removal of markings is achieved by water blasting, shot blasting, sand blasting, chemical removal, or other acceptable means that do not harm the pavement. The FAA does not endorse painting over the old markings because this practice merely preserves the old marking, which in some cases have misled pilots, and requires additional maintenance. Precaution: Special consideration should be placed on the size and shape of removal areas when removing runway markings associated with the relocation of a runway threshold or its displacement so that the resulting area of discolored pavement resulting from the removal process does not result in the continued visual appearance of a marked pavement. That is, the size and shape of the removal area(s) need to be much larger than the marking to be removed.

f. Painted Numbering System for Record Keeping of Surface Painted Markings. To facilitate the daily inspection, scheduled maintenance, necessary repairs, etc. for surface markings the airport operator may use a numbering system or alphanumeric system that is located in a corner of the surface marking. Figure 1-1 shows a numbering system adopted by Dallas/Fort Worth (DFW) International Airport for identifying each surface marking listed in their Sign Plan. If employed, the

CHAPTER 1. › 1.4. REQUIREMENTS AND RECOMMENDATIONS FOR ENHANCED CONSPICUITY OF…

height of the inscription should be small and inconspicuous to all viewers except an individual standing next to the surface marking.

Figure 1-1. Example of DFW Painted Numbering System for Surface Painted Markings 1.4. REQUIREMENTS AND RECOMMENDATIONS FOR ENHANCED CONSPICUITY OF SURFACE MARKINGS. Surface markings that cannot be seen by pilots and other individuals operating on paved airfield surfaces are useless. Two proven techniques that help airport operators enhance the conspicuity of surface markings are (1) outlining surface markings with black borders on light-colored pavements and (2) placing glass beads in paint. However, glass beads are not to be used in black paint. Table 1-1 serves as a general guide for determining when existing asphalt concrete surfaces or asphalt treated surfaces may be classified as a light-colored pavement, i.e., when to outline a required surface marking with a black border.

Table 1-1. General Guidelines for Determining Light-Colored Pavements

Painting a Black Border

Pavement Surface Type

Age of Pavement Surface 1

New Up to 2 years

old

Over 2 years

old

Portland Cement Concrete

Surfaces

Yes Yes Yes

Asphalt Concrete Surfaces No No Yes Asphalt Treated Surfaces No No Yes

Note 1: This table serves only as a general guide since an existing asphalt pavement at one airport location may not experience the same rate of surface color deterioration as at another airport location.

a. Technique 1 – Outlining Surface Markings with Black Borders on Light-Colored Pavements. The degree of contrast (conspicuity) between surface markings on light-color pavements, in particular on concrete and older asphalt pavements, can be increased by outlining all edges of the surface

marking with a black border. Appendix B provides illustrations of recommended patterns for various surface markings outlined in black. Black borders, except for enhanced taxiway centerline applications, should be at least 6 inches (15 cm) or greater in width to enhance the conspicuity of certain painted surface markings on light-color pavements. The borders for the outside dashes of the enhanced taxiway centerline marking can range from 3 to 6 inches (7.5 – 15 cm).

(1) Surface Markings that Require Black Borders.

(i) All holding position markings used on runways, taxiways, and holding bays and used to indicate ILS/MLS or precision obstacle free zone (POFZ) critical areas (per paragraphs 3.2, 3.3, 3.4, and 3.5) and the non-movement area boundary marking (per paragraph 5.4). (ii) Intermediate holding position marking for taxiway/taxiway intersections (per paragraph 3.6).

(iii) All taxiway centerline markings on taxi routes designated as surface movement guidance and control system (SMGCS) routes (per paragraph 4.2).

(iv) Enhanced taxiway centerline marking (per paragraph 4.3). (v) Surface painted holding position sign marking (per paragraph 4.5). (vi) Geographic position marking (per paragraph 4.11).

(2) Surface Markings Recommended for Black Borders. This advisory circular strongly recommends outlining all other markings not listed in paragraph 1.4(a)(1), particularly taxiway centerlines per paragraph 4.2.

b. Technique 2 – Use of Glass Beads on Permanent Pavement Markings. Glass beads identified in Item P-620 of AC 150/5370-10 are an effective means of enhancing the conspicuity of surface markings when aircraft and vehicles operate at night, during low-visibility conditions, or when the pavement surface is wet. Due to the additional increase in marking conspicuity caused by certain glass beads, the FAA recommends that runway holding position markings contain either Type III or Type IV glass beads as determined by the airport operator. If Type IV glass beads that have a larger diameter are used, then they should only be applied in higher-built materials, such as TT-P-1952E-Type III waterborne paint, epoxy, methyl methylacrylate, or preformed thermoplastic. Precaution: As previously stated, glass beads should never be used in black paint.

Glass Bead Requirement Paragraph 620-3.5, Application, per AC 150/5370-10

(General) Glass beads shall be distributed upon the marked areas at the locations shown on the plans to receive glass beads immediately after application of the paint. A dispenser shall be furnished that is properly designed for attachment to the marking machine and suitable for dispensing glass beads. Glass beads shall be applied at the rate(s) shown in Table 1 of AC 150/5370-10. Glass beads shall not be applied to black paint. Glass beads shall adhere to the cured paint or all marking operations shall cease until corrections are made.

(1) Surface Markings that Require Glass Beads.

(i) All holding position markings used on runways, taxiways, and holding bays and used to indicate ILS/MLS or POFZ critical areas (per paragraphs 3.2, 3.3, 3.4, and 3.5).

(ii) Runway threshold marking (per paragraph 2.5). (iii) Runway threshold bar marking (per paragraph 2.9(a)). (iv) Runway aiming point marking (per paragraph 2.6). (v) Runway landing designator marking (per paragraph 2.3). (vi) Runway touchdown zone marking (per paragraph 2.7). (vii) Runway centerline marking (per paragraph 2.4). (viii) Taxiway centerline marking (per paragraph 4.2).

(ix) Enhanced taxiway centerline marking (per paragraph 4.3). (x) Geographic position marking (per paragraph 4.11). (xi) Surface painted signs for holding position signs (paragraph 4.5), taxiway direction signs (paragraph 4.6), taxiway location signs (paragraph 4.7), gate destination signs (paragraph 4.8), and apron entrance point signs (paragraph 4.9).

(xii) Non-movement area boundary marking (per paragraph 5.4).

(2) Surface Markings Recommended for Glass Beads.

(i) Runway side stripe marking (per paragraph 2.8). (ii) Taxiway edge marking (per paragraph 4.4). (iii) Runway displaced threshold marking (per paragraph 2.9). (iv) Runway demarcation bar marking (per paragraph 2.9(c)).

Blank Page

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.1. APPLICATION.

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. 2.1. APPLICATION. The minimum requirements for surface marking schemes used for runways are a direct function of the approach category for each runway threshold and the existence of displaced thresholds, stopways, blast pads, or extra wide shoulders. Runways having the same approach category off both runway thresholds will show the same surface marking scheme from threshold to threshold (with some exceptions, such as the runway designator.) In comparison, runways with different approach categories will show two different surface marking schemes. The complete runway surface marking schemes required by a runway combine table 2-1 requirements with the physical structure and usage of the runway.

a. Table 2-1 identifies the minimum required surface marking schemes for paved runways according to their threshold approach category. Figures 1, 2, 3, and 5 provide the dimensional standards for the surface marking schemes. An airport operator may paint a runway with additional surface marking schemes than required, such as a visual runway with runway side stripes or the aiming point marking, if deemed necessary by the FAA. Furthermore, surface markings beyond those described in table 2-1 are required to support particular operations, such as a displaced threshold, or to identify runway related features, such as blast pads or stopways.

Table 2-1. Minimum Required Runway Surface Marking Schemes for Paved Runways

Threshold Approach Category

Runway

Surface Marking

Scheme

Visual

Approach

Non-precision

Approach

(And approaches with

vertical guidance not lower than ¾ -statute mile

visibility)

Precision Approach

(Approaches with

vertical guidance lower than ¾ -statute

mile visibility)

Landing Designator (par. 2.3) X X X

Centerline (par. 2.4) X X X

Threshold (par. 2.5) Note 1 X X

Aiming Point (par. 2.6) Note 2 Note 3 X

Touchdown Zone (par. 2.7) X

Side Stripes (par. 2.8) Note 4 Note 4 X

Note 1: Required on runways serving approach categories C and D airplanes and for runways used, or

intended to be used, by international commercial air transport. Note 2: Required on 4,200-foot (1,280 m) or longer runways serving approach categories C and D

airplanes. Note 3: Required on 4,200-foot (1,280 m) or longer instrumented runways. Note 4: Used when the full runway pavement width may not be available for use as a runway.

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.2. INTERRUPTION OF RUNWAY SURFACE MARKINGS.

b. Runways with a displaced threshold, blast pad, stopway, or extra wide shoulders require additional marking schemes not identified in table 2-1. These surface marking schemes and others not in table 2-1 are discussed separately in this advisory circular. See AC 150/5300-13 for detailed information about the location of displaced thresholds, blast pads, and stopways.

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

(Painting) The dimensional size for the runway surface marking promulgated by this advisory circular is based on the assumption that the runway has a standard runway width as prescribed by AC 150/5300-13. For convenience, the standard widths are shown in table 2-2 below. Airport operators with non-standard runway widths may, for specified surface markings, proportionally adjust the marking’s width to be less than the standard scheme. Under substandard conditions, the width of marking is in direct proportion to the available runway width. However, the corresponding length for the marking is never reduced. Subsequent paragraphs in this advisory circular will specify, via a green-shaded, solution box, those runway surface markings that may be proportioned. The absence of a green-shaded, solution box in a subsequent paragraph implies that that runway surface marking, such as the runway centerline, is not to be decreased in width even if other nearby runway surface markings are proportionally adjusted. 2.2. INTERRUPTION OF RUNWAY SURFACE MARKINGS. At the intersection of two runways, the surface markings of one runway are, with the possible exception of runway side stripes (such as closed V-shaped runways), fully displayed through the intersection while the surface markings of the other runway are completely interrupted. This process of removing runway surface markings from one runway establishes an order of precedence among the different runways.

a. Order of Precedence. The order of precedence for displaying the runway surface marking schemes of one runway over the other runway at the intersection of these runways should follow this order:

(1) Precision approach runway, Category III. (2) Precision approach runway, Category II. (3) Precision approach runway, Category I. (4) Non-precision approach runway. (5) Visual runway. For an intersection of runways of the same precedence, the preferred higher precedence runway is the one having the lowest approach minimums or the runway end most often used.

b. Lesser Precedence Runways. The manner in which a lesser precedence runway intersects a higher precedence runway may require the shifting or complete removal of certain surface markings that fall within the intersection. As shown in figure 4, the most affected surface markings are the runway centerline, runway side stripes, aiming point markings, and runway touchdown zone markings. The

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.3. RUNWAY LANDING DESIGNATOR MARKING.

11/17/2010 AC 150/5340-1K Change 1

latter two runway markings may have implications when shifted or removed. See paragraphs 2.2(c) and 2.6 for shifting an aiming point marking, and see paragraph 2.7 for removing touchdown zone markings. c. Consequences When Shifting the Aiming Point Markings. Figure 4 shows one possible conflict that could occur when the aiming point markings are relocated.

(1) When the aiming point markings of a given runway that are in the intersection of two runways need to be moved more than 200 feet (61 m) away from the existing threshold, the airport operator will have to displace the existing threshold or designate a new runway end (threshold) in order to retain the distance between the threshold and the aiming point marking as illustrated in the bottom illustration of figure 4. The preferred distance to be maintained between the newly designated threshold and the shifted aiming point marking is 1,020 feet (311 m); see paragraph 2.6.

(2) Runways with an approach landing aid, such as Precision Approach Path Indicators (PAPIs) or Visual Approach Slope Indicators (VASIs), which are co-located with the aiming point markings, can be negatively affected when an excessive shifting of the aiming point marking occurs. The consequence could be a non-compatible threshold crossing height for landing airplanes. When the aiming point markings are shifted more than 60 feet (18.3 m), the co-located PAPI or VASI should be evaluated for relocation to provide a correct vertical guidance to pilots. See paragraph 7.5, Design (of Economy Approach Aids) and table 7.1, Threshold Crossing Heights, of AC 150/5340-30, Design and Installation Details for Airport Visual Aids, to determine if the impact of shifted aiming point markings warrants a relocation of the co-located PAPI (or other runway approach aids).

(3) For landing safety, the FAA requires that whenever the distance between the threshold and aiming point markings is 1,220 feet (372 m) or more, the airport operators place a note in the Airport/Facility Directory (A/FD) to inform pilots about the increased distance existing between the threshold and the aiming point markings.

d. Closed V-Shaped Runway Ends Configuration. The closed V-shaped runway ends configuration is a pavement geometry where two runway ends commence from the same location but proceed in different directions. This undesirable geometry requires a special shifting procedure of the runway landing designator marking of the lesser precedence runway further down the runway than prescribed by paragraph 2.3. The special procedure is as follows. On the lesser order runway, locate the point on its runway centerline that is perpendicular to the inside common corner of the two intersecting runways. Once this base point is located, move this base point 20 feet (6.5 m) down the runway centerline to relocate the bottom of the letter or number(s) used for the runway landing designator. For an intersection of runways of the same precedence, the preferred higher precedence runway is the one having the lowest approach minimums or the runway end most often used.

Wrong-Runway Takeoffs Mitigation

(Safety) In an effort to eliminate the possibility of a “wrong-runway” takeoff operation by pilots, the airport operator should reconstruct closed V-shaped runway geometries to a different geometry, possibly an X-shaped geometry. 2.3. RUNWAY LANDING DESIGNATOR MARKING.

a. Purpose. The runway landing designator marking identifies a runway end.

b. Location. Runway landing designator marking(s) must be located from the runway threshold per figures 1, 2, and 3 or from the displaced threshold per figure 6. All these figures show the start location for both types of thresholds.

c. Color. Runway landing designator markings are white. See paragraph 1.4, Requirements and Recommendations for Enhanced Conspicuity of Surface Markings, for required and recommended techniques to enhance visibility of this surface marking.

d. Characteristics.

(1) A runway landing designator marking consists of a single number or two numbers. When parallel runways exist, the number(s) are further supplemented with a letter.

(2) A single-digit runway landing designation number is never preceded by a zero. (3) For single runways, dual parallel runways, and triple parallel runways, the designator number is the whole number nearest the one-tenth of the magnetic azimuth along the runway centerline when viewed from the direction of approach. For example, where the magnetic azimuth along the runway centerline is 183 degrees, the runway designator marking would be 18; for a magnetic azimuth of 87 degrees, the runway designation marking would be 9. For a magnetic azimuth ending in the number “5” such as 185 degrees, the runway designator marking can be either 18 or 19.

(4) On four or more parallel runways, one set of adjacent runways is numbered to the nearest one-tenth of the magnetic azimuth and the other set of adjacent runways is numbered to the next nearest one-tenth of the magnetic azimuth.

(5) For parallel runways, each runway landing designator number must be supplemented by a letter, in the order shown from left to right when viewed from the direction of approach as prescribed by the following marking criteria. Different labeling patterns than those prescribed below are permissible under certain circumstances as identified in subparagraph 2.3(d)(6).

(i) Two parallel runways having a magnetic azimuth of 182 degrees – the runways would be designated “18L,” “18R.”

(ii) Three parallel runways having a magnetic azimuth of 87 degrees – the runways would be designated “9L,” “9C,” “9R.”

(iii) Four parallel runways having a magnetic azimuth of 324 degrees – the runways would be designated “32L,” “32R,” “33L,” “33R.”

(iv) Five parallel runways having a magnetic azimuth of 138 degrees – the runways would be designated “13L,” “13R,” “14L,” “14C,” “14R” or “14L,” “14R,” “13L,” “13C,” “13R.” Other combinations exist for this case. See paragraph 2.3(d)(6).

(v) Six parallel runways having a magnetic azimuth of 83 degrees – the runways would be designated “8L,” “8C,” “8R,” “9L,” “9C,” “9R.” Other combinations exist for this case. See paragraph 2.3(d)(6).

(vi) Seven parallel runways having a magnetic azimuth of 85 degrees – the runways would be designated “8L,” “8C,” “8R,” “9L,” “9C,” “9R,” “10.” Other combinations exist for this case. See paragraph 2.3(d)(6).

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.4. RUNWAY CENTERLINE MARKING.

(6) There are certain runway placements where the surface marking schemes for parallel runways provided in subparagraph 2.3(d)(5) may not be appropriate because their orientation may lead to pilot confusion. For example, the marking scheme recommended for parallel runways on the same side of a terminal is to follow subparagraph 2.3(d)(5). However, when two parallel runways are separated by a large terminal or several terminals, it is preferable to designate the runways as non-parallel runways to avoid pilot confusion. Another case that may cause pilot confusion is a turf runway that is parallel to paved visual runway but at a great distance from a higher precedence paved runway. In general, the airport operator should carefully choose how to mark parallel runways to eliminate pilot confusion.

(7) The appearance of the letters and numbers used for runway landing designator markings are in the form and proportion as shown in figure 5. The spacing between numbers and letters are as shown in figures 1, 2, 3, and 5. However, with the exception of the numerals 6 and 9, all numerals and the letters L, C, and R are 60 feet (18.3 m) in height. Numerals 6 and 9, which are 63 feet (18.9 m) in height, follow the Rule of 69. That is, although the numerals 6 and 9 are taller, the 3-foot tips of the numerals are ignored so that their separations from the threshold markings, the letters L-C-R, the first runway centerline, and the start of the runway threshold remain as shown in figures 1, 2, and 3.

Application of Proportioning Runway Markings for Airplane Design Group (ADG) I Runway Width

(Painting) Due to the space limitations on very narrow runways, the size and spacing of the numbers and letters are reduced only when necessary such that the painted runway landing designator is no closer than 2 feet (0.6 m) from the runway edge or runway side stripes. For example, this problem may occur when painting certain dual-numbered runway landing designators spaced 15 feet (4.5 m) apart on an ADG I runway width of 60 feet (18.3 m). In such cases, first reduce the 15-foot (4.5-m) spacing to 10 feet (3.1 m) and retain the size of numerals and letter per figure 5. Second, reduce the 15-foot (4.5-m) spacing to 10 feet (3.1 m) and reduced the size of numerals and letter proportionally to maintain the 2-foot (0.6 m) edge or runway side stripe clearance. 2.4. RUNWAY CENTERLINE MARKING.

a. Purpose. The runway centerline marking identifies the physical center of the runway width and provides alignment guidance to pilots during takeoff and landing operations. For lighting provisions, see AC 150/5340-30.

b. Location. A runway centerline marking is located along the physical center of the runway width and spaced between the runway landing designation markings as shown in figures 1, 2, and 3.

c. Color. The runway centerline marking is white. See paragraph 1.4 for required and recommended techniques to enhance this surface marking.

d. Characteristics. A runway centerline marking consists of a line of uniformly spaced stripes and gaps and of uniform width.

(1) The stripes are 120 feet (36.5 m) in length and the gaps are 80 feet (24.3 m) in length.

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.5. RUNWAY THRESHOLD MARKING.

AC 150/5340-1K Change 1 11/17/2010

(2) The minimum width of the stripes is:

 36 inches (90 cm) for precision runways.  18 inches (45 cm) for non-precision runways.  12 inches (30 cm) for visual runways.

(3) To accommodate varying runway lengths, all adjustments to the uniform pattern of runway centerline stripes and gaps are made near the runway midpoint (defined as the distance between the two thresholds or displaced thresholds). Under such cases, reduce the lengths of both the stripes and gaps starting from midpoint and proceed toward the runway thresholds. Reduced stripes must be at least 80 feet (24 m) in length, and the reduced gaps must be at least 40 feet (12.3 m) in length. The affected stripes and gaps within the section should show a uniform pattern. 2.5. RUNWAY THRESHOLD MARKING.

a. Purpose. A runway threshold marking, which commences 20 feet (6 m) from the actual start point of runway threshold, closely identifies the actual beginning point of the runway threshold used for landings. For lighting provisions, see AC 150/5340-30.

b. Location. The runway threshold marking starts 20 feet (6 m) from the actual start point of the runway threshold as shown in figures 1 and 2. This value remains the same even though a 10-foot (3m) white threshold bar is introduced, such as for displaced thresholds or the addition of a blast pad or stopway as shown in figure 8. Previously, when a displaced threshold was painted or a blast pad or stopway added, the 20-foot (6-m) dimension was increased to 30 feet (9 m) to accommodate the requirement for painting the runway threshold bar. When a runway is completely remarked, the newly painted displaced threshold and threshold bar markings are 10 feet (3 m) apart as shown in figure 6.

c. Color. The components of a runway threshold marking are white. See paragraph 1.4 for required and recommended techniques to enhance this surface marking.

d. Characteristics. The runway threshold marking consists of a pattern of longitudinal stripes of uniform dimensions spaced symmetrically about the runway centerline. The number of longitudinal stripes and their spacing is determined by the runway width.

(1) Table 2-2 provides the number of longitudinal stripes for runways having standard runway widths as defined by AC 150/5300-13. Figure 1 illustrates the pattern for a 150-foot (45-m) wide runway. See paragraph 2.5(d)(3) for painting guidance applicable to non-standard runway widths.

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.6. RUNWAY AIMING POINT MARKING.

Table 2-2. Number of Runway Threshold Stripes for Standard Runway Widths

Standard runway

widths

Number of symmetrical stripes

60 feet (18.3 m) 4

75 feet (22.9 m) 6

100 feet (30.5 m) 8

150 feet (45.7 m) 12

200 feet (61 m) 16

(2) For standard runway widths, the longitudinal stripes are 150 feet (45.7 m) long and 5.75 feet (1.75 m) wide with the outer edges spaced (stripe-gap) 5.75 feet (1.75 m) apart. However, the two longitudinal stripes nearest the runway centerline are doubled spaced, i.e., outer edges of the near-most pair are 11.5 feet (3.5 m) apart. Figure 1 illustrates the stripe-gap pattern for 150-foot (46 m) wide runways. The stripe-gap pattern allows sufficient room to paint runway side stripes without interfering with the outermost longitudinal stripes.

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

(Painting) For standard 75-foot (23-m) wide runways that use 36-inch (90-cm) wide runway side stripes, the stripe-gap pattern of 5.75 feet (1.75 m) is reduced to 5.50 feet (1.68 m).

(3) For non-standard runway widths, the same stripe-gap pattern is continued from the runway centerline until the outermost longitudinal stripe is not closer than 4 feet (1.2 m) from the runway edge. For example, for a non-standard 125-foot (38-m) wide runway, the stripe-gap pattern yields a total of 10 longitudinal stripes symmetrical about the runway centerline. In no case should the stripe-gap pattern exceed 92 feet (27 m) on either side of the runway centerline. The value of 92 feet (27 m) is the width for the pattern used on the standard 200-foot (61-m) wide runways.

(4) When there is pavement in excess of 5 feet (1.5 m) prior to the actual start of the runway threshold and (a) pilots may confuse the pavement as part of the actual runway or (b) the pavement does not have the same load bearing capacity as the runway, then painting of a runway threshold bar per paragraph 2.9 is required. In contrast, if the installation of landing threshold lights requires pavement to support the light fixtures and the supportive pavement abuts the start point of the runway threshold, then the supportive pavement is not considered a part of the runway. In this instance, the painting of a runway threshold bar is not required. 2.6. RUNWAY AIMING POINT MARKING.

a. Purpose. A runway aiming point marking provides a visual aiming point for landing operations.

b. Location. The preferred beginning of the aiming point marking starts 1,020 feet (311 m) from the runway threshold as shown in figures 1, 2, and 3. However, this preferred separation is not adequate for all cases as partially discussed below.

AC 150/5340-1K Change 1 11/17/2010

Note: The term preferred assumes the following conditions: standard visual glide slope of 3 degrees; no obstacle in the approach area affecting the obstacle clearance surface of the PAPI; standard threshold crossing heights per table 7-1, Threshold Crossing Heights, of AC 150/5340- 30; sufficient runway length so not to force the placement of the aiming point marking; no rapid terrain drop off near the approach threshold that encounters severe turbulence; no elevation differences between the threshold and the installation zone of the PAPI.

(1) Intersecting Runways. A separation tolerance of plus or minus 200 feet (61 m) is allowed when it is necessary to shift the aiming point marking to avoid overlapping aiming point markings at dual runway intersection as shown in figure 4 and discussed in paragraph 2.2(c). However, depending on the threshold crossing heights and the available runway approach aids, the shifting of the aiming point markings may negatively impact the threshold crossing heights for approaching airplanes. One potential impact of the shift is to the co-located runway approach aids, such as the PAPI, in which the previous vertical guidance offered by the aiming point marking to pilots is now incompatible with the threshold crossing height associated with the runway approach aid. Under such conditions, adjustment in the location of the affected runway approach aid may be necessary after an evaluation so that the colocated relationship between the PAPI (and other approach aids) and the shifted aiming point marking permits an acceptable landing operation for both landing aids.

(2) Compatible Threshold Crossing Heights. See paragraph 7.5, Design (of Economy Approach Aids) and table 7-1, Threshold Crossing Heights, of AC 150/5340-30 to determine if the impact of a relocated aiming point marking warrants relocating the co-located PAPI (or other runway approach aids).

c. Color. The runway aiming point marking is white. See paragraph 1.4 for required and recommended techniques to enhance this surface marking.

d. Characteristics.

(1) The runway aiming point marking consists of two conspicuous rectangular markings, 150 feet (45.7 m) in length for runways of at least 4,200 feet (1,280 m) in length between the thresholds (or a displaced threshold(s)) and 100 feet (30.5 m) in length for lesser lengths between the thresholds (or a displaced threshold(s)), that are located symmetrically on each side of the runway centerline as shown in figures 1, 2, and 3. See table 2-2 for the dimensions of standard runway widths per AC 150/5300-13.

(2) The width of each rectangular marking is as follows:

(i) 30 feet (9.1 m) for standard runway widths of 150 feet (45.7 m) or greater. (ii) 20 feet (6 m) for standard runway widths of 100 feet (30.5 m).

(iii) 15 feet (5 m) for standard runway widths of 75 feet (22.9 m).

(iv) 12 feet (3.7 m) for a standard runway width of 60 feet (18.3 m). (3) The lateral spacing between the inner sides of the runway aiming point markings is as follows:

(i) For runways of 150 feet (45.7 m) or more in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 72 feet (21.9 m).

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.7. RUNWAY TOUCHDOWN ZONE MARKING.

11/17/2010 AC 150/5340-1K Change 1

(ii) For runways of 100 feet (30.5 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 48 feet (14.6 m).

(iii) For runways of 75 feet (22.9 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 36 feet (11.0 m).

(iv) For runways of 60 feet (18.3 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 28.8 feet (8.8 m).

Application of Proportioning Runway Markings

for Non-Standard Runway Widths and for Standard Runway Widths less than 150 feet (45.7 m)

(Painting) For runways with widths below 150 feet (45.7 m), the width of the rectangular bars and their lateral spacing between the inner sides of the rectangular bars are adjusted in proportion to the available runway width by using the 150-foot (45.7 m) width runway parameters to determine the percentage decrease in lateral spacing and width of each marking. For example, a non-standard 70-foot wide runway would apply 70/150 = 0.467 to obtain a lateral spacing of 72 x 0.467 = 33.6 feet (10.25 m) between the pair and an individual width of 30 x 0.467 = 14 feet (4.27 m). If runway side stripes are also painted, which are not reduced, then the adjustment should add the width of the corresponding runway side stripes plus a minimum 1-foot (0.3-m) clearance between the outer edge of the aiming point marking and the runway side stripe. Lateral spacing – in no case is the lateral spacing less than 30 feet (9.1 m) except for runways less than 75 feet (22.9 m). Lengths – in all cases, the length of the aiming point marking remains unchanged. 2.7. RUNWAY TOUCHDOWN ZONE MARKING.

a. Purpose. For landing operations, the touchdown zone marking identifies the touchdown zone along a precision runway in 500-foot (152-m) increments. For lighting provisions, see AC 150/5340-30. b. Location. The touchdown zone marking consists of symmetrically arranged pairs of rectangular bars in groups of one, two, and three along the runway centerline as shown in figure 1. As shown, there are five groupings with the aiming point marking serving as an independent, sixth pair.

(1) The touchdown zone marking scheme maintains a 900-foot (275-m) “no-marking zone” from the midpoint of the runway back toward the threshold. That is, those pairs of surface markings that extend within 900 feet (275 m) of the runway midpoint are eliminated. The intent of this painting practice is to preserve a 1,800-foot (550-m) unmarked area so pilots do not confuse the surface markings during a landing with the surface markings for the other approach procedure. The same practice applies equally to a displaced threshold, i.e., the midpoint is located between the thresholds or displaced thresholds and not the runway ends. Taking this into consideration, the painted pattern for the runway touchdown zone marking depends on the (a) authorized approach off each runway and (b) the available length between the runway thresholds or displaced threshold, i.e., the midpoint. The surface marking patterns for the two possible cases are provided in table 2-3 (case #1) and table 2-4 (case #2).

AC 150/5340-1K Change 1 11/17/2010

Case #1 – Only one runway end requires the runway touchdown zone marking scheme. Apply table 2-3 criteria, which take into account the “no-marking zone” of 900 feet (275 m) from the midpoint back toward the threshold.

Table 2-3. Pairs of Touchdown Zone Markings Required When Installed From One Threshold

Distance Between Thresholds

(or displaced thresholds)

Markings for Precision Approach End (includes

displaced threshold)

Other Runway End

Visual or Non-precision

6,065 ft (1849 m) or greater1 Full set of markings Aiming point marking

5,565 ft (1697 m) to 6,064 ft (1848 m) Less one pair of rectangular bar markings2

Aiming point marking

5,065 ft (1544 m) to 5,564 ft (1696 m) Less two pairs of rectangular bar markings

Aiming point marking

4,565 ft (1391 m) to 5,064 ft (1543 m) Less three pairs of rectangular bar markings

Aiming point marking

Note 1: The value of 6,065 feet is derived as follows. For the non-precision or visual runway end, the table assumes the 900-foot “no-marking zone” criterion plus the length of a preferred aiming point marking, which starts 1,020 feet from the start of the threshold to obtain a length of 1,920 feet. Add to this the length of the aiming point marking. Per paragraph 2.6(d)(1), the length of the aiming point marking is either 150 feet or 100 feet. This table uses a length of 150 feet because all the entries in column #1 are greater than 4,200 feet. Therefore, adding 150 feet to 1,920 feet obtains a length of 2,070 feet. For the precision end, which equals 3,995 feet, it assumes the 900-foot “no-marking zone” followed by the standard 75-foot-long rectangular bar for a total length of 975 feet. Add to this value the full 3,000-foot touchdown zone marking scheme and the 20-foot separation between the actual starting point of the runway threshold (or displaced threshold) and the bottom edge of threshold marking to obtain 3,995 feet. Summing the values 3,995 and 2,070 yields 6,065 feet.

Note 2: Each reduction in a pair of rectangular bar markings from the precision end equates to a 500foot (152-m) reduction between the thresholds. The painting rationale for this table is to ignore the midpoint between the thresholds so the precision instrumented landing is favored over non-precision or visual landings. That is, the length of the nonprecision/visual side of the runways always remains at 2,070 feet in length to promote the painting of a full set of touchdown zone markings. Case #2 – Both runway ends require runway touchdown zone markings. Apply table 2-4 criteria, which take into account the “no-marking zones” of 1,800 feet (550 m) from the threshold-to-threshold midpoint.

11/17/2010 AC 150/5340-1K Change 1

Table 2-4. Pairs of Touchdown Zone Markings Required When Installed From Both Thresholds

Distance Between Thresholds

(or displaced thresholds)

Markings for Each Threshold

(or displaced threshold)

7,990 ft (2436 m) or greater1 Full set of markings

6,990 ft (2130 m) to 7,989 ft (2435 m) Less one pair of rectangular bars from each side

nearest to the runway midpoint2

5,990 ft (1826 m) to 6,989 ft (2129 m) Less two pairs of rectangular bars from each side

nearest to the runway midpoint2

4,990 ft (1521 m) to 5,989 ft (1825 m) Less three pairs of rectangular bars from each side

nearest to the runway midpoint2

Note 1: The value of 7,990 feet is derived as follows. Proceed from the runway midpoint in one direction, and you will have the 900-foot “no-marking zone” criterion followed by the standard 75-foot long rectangular bar for a total length of 975 feet. Add to this value the full 3,000-foot touchdown zone marking scheme plus the 20-foot separation between the actual starting point of the runway threshold (or displaced threshold) and the edge of threshold marking to obtain 3,995 feet. Double this value for both directions to obtain 7,990 feet.

Note 2: Each reduction in a pair of rectangular bar markings from both sides equates to a 1,000-foot (305-m) reduction between the thresholds.

The painting rationale for this table is to preserve the midpoint between the thresholds, thereby promoting an equal treatment of painting pairs of rectangular bar markings for both sides.

(2) Because the location of the aiming point marking may be adjusted from the threshold to accommodate different approach slopes and/or heights over the threshold and to possibly take into account non-zero runway gradients, the location of an adjusted aiming point marking will vary. Please see AC 150/5340-30. Under such conditions, an adjusted aiming point will, in most cases, continue to be located between the first and the second touchdown zone markings. However, when the accumulative effect of the adjustments is severe (defined as when a touchdown zone marking coincides with or is within 160 feet (48.8 m) of the adjusted aiming point marking), that touchdown zone marking must not be painted. For the pilot community, this practice permits the aiming point marking to retain its prominent visual landing aid as compared to a touchdown zone marking.

c. Color. All rectangular bars are white. See paragraph 1.4 for required and recommended techniques to enhance this marking.

d. Characteristics.

(1) For runway widths of 150 feet (45.7 m) or greater, each rectangular bar is 75 feet (22.9 m) long and 6 feet (1.8 m) wide. The lateral spacing between the inner sides of the rectangular bars on the same side of the runway centerline is 5 feet (1.5 m).

(2) For runway widths less than 150 feet (45.7 m), the length of the marking remains unchanged, but the width and the lateral spacing between the markings are reduced proportionally to the decrease in runway width by using 150-foot (45.7 m) parameters to determine the percentage decrease.

(3) The lateral spacing between the inner sides of the rectangular bars centered along the runway centerline is equal to that of the aiming point marking (criteria repeated below from paragraph

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.8. RUNWAY SIDE STRIPE MARKING.

AC 150/5340-1K Change 1 11/17/2010

2.6(d)(3)). In all cases, the length of the rectangular bars (and the aiming point markings) remains unchanged. See table 2-2 for the dimensions of standard runway widths.

(i) For runways of 150 feet (45.7 m) or more in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 72 feet (21.6 m).

(ii) For runways of 100 feet (30.5 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 48 feet (14.6 m).

(iii) For runways of 75 feet (22.9 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 36 feet (11.0 m).

(iv) For runways of 60 feet (18.3 m) in width, the lateral spacing between the inner sides of the rectangular bars centered on the runway centerline is 28.8 feet (8.8 m).

Application of Proportioning Runway Markings

for Non-Standard Runway Widths

(Painting) For runways with widths below 150 feet (45.7 m), the width of the rectangular bars and their lateral spacing between the inner sides of the rectangular bars are adjusted in proportion to the available runway width by using the 150-foot (45.7 m) width runway parameters to determine the percentage decrease in lateral spacings and width of the marking. For example, a nonstandard 70-foot wide runway would apply 70/150 = 0.467 to obtain a lateral spacing for the centered pair of 72 x 0.467 = 33.6 feet (10.25 m), a lateral spacing for other pairs of 5 x 0.467 = 2.3 ft (0.7 m), and a width of 6 feet x 0.467 = 2.8 feet (0.85 m). This adjustment must be such that the inner sides of the innermost rectangular bars to the runway centerline align themselves with the inner side of the aiming point marking. Given that the runway side stripes are painted, the adjustment should be such that the clearance between the runway side strip and the outer edge of the three-bar grouping is a minimum of 1-foot (0.3 m). In no case should the three-bar group be painted further out from the runway centerline than the aiming point marking.

2.8. RUNWAY SIDE STRIPE MARKING.

a. Purpose. The runway side stripe marking provides enhanced visual contrast between the runway edge and the surrounding terrain or runway shoulders and delineates the width of suitable paved area for runway operations. For lighting provisions, see AC 150/5340-30.

b. Location. The runway side stripe marking consists of two parallel stripes, one placed along each edge of the usable runway with the outer edge of each stripe approximately on the edge of the paved useable runway. For extra wide runways, such as military runways converted for public use, the maximum distance between the outer edges of the parallel stripes is 200 feet (61 m). Figure 1 illustrates the runway side stripe marking.

c. Color. The stripes of the runway side stripe marking are white. See paragraph 1.4 for required and recommended techniques to enhance this marking.

d. Characteristics. The runway side stripe marking has a minimum width of 36 inches (90 cm) for runways of 100 feet (30.5 m) or wider in width and at least 18 inches (45 cm) on smaller width runways (see table 2-2 for standard runway widths).

(1) For runways with a displaced threshold, the side stripes continue through the paved area prior to the displaced threshold as shown in figure 6. This continuation of the side stripes is required because this paved area is used for takeoffs and landing rollouts from the other direction.

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.9. RUNWAY DISPLACED THRESHOLD MARKING.

(2) Where an aligned taxiway, as shown in figures 7 and 9, precedes a runway threshold, both side stripes will terminate. The point of termination of the side stripes is determined by the taxiway geometry. The FAA recommends that airport operators not construct new aligned taxiways. The FAA further recommends that existing aligned taxiways be removed or reconfigured into usable runways, for example, as shown in figures 6 and 10.

(3) When a taxiway connects to a runway or the runway has turn pads or turnarounds, the runway side stripe marking remains continuous between the runway and these adjoining infrastructures.

(4) For intersecting runways, see guidance in paragraph 2.2, Interruption of Runway Surface Markings. 2.9. RUNWAY DISPLACED THRESHOLD MARKING. The marking scheme for a runway with a displaced threshold, when required by paragraph 2.1, includes a runway threshold bar and arrowheads with and without arrow shafts. Figures 6, 9, and 10 illustrate the various applications of displaced thresholds and the requirement for additional marking components. For lighting provisions, see AC 150/5340-30.

a. Runway Threshold Bar Marking.

(1) Purpose. The runway threshold bar marking delineates the beginning section of the runway available for landing from the unusable section on the approach side of the displaced threshold.

(2) Location. The runway threshold bar marking is an elongated rectangular bar that is located perpendicular to the runway centerline and on the landing portion of the runway. The outboard edge of the marking is aligned with the location labeled “start of runway displaced threshold” as shown in figure 6.

(3) Color. The runway threshold bar marking is white. See paragraph 1.4 for required and recommended techniques to enhance this marking.

(4) Characteristics. The runway threshold bar marking is 10 feet (3.1 m) in width and extends between the runway edges or between the runway side stripe markings.

b. Arrow Marking. The arrow marking (arrowheads with and without arrow shafts) performs three possible functions, that is, two cases for displaced thresholds and one case for a runway threshold with an aligned taxiway.

(1) Purposes.

(i) Figure 6 illustrates the predominant case in which the threshold is displaced from the runway end. In this case white arrowheads with and without arrow shafts are required to identify the portion of the runway before the displaced threshold to provide centerline guidance for pilots during approaches, takeoffs, and landing rollouts from the opposite direction.

(ii) Figure 9 illustrates the rare case in which a displaced threshold is preceded by an aligned taxiway. In this case white arrowheads with and without arrow shafts and yellow arrowheads without arrow shafts are required to identify the runway portion from the aligned taxiway portion. Furthermore, a yellow runway demarcation bar is required to identify the start of the runway. See paragraph 2.9(c) for runway demarcation bar criteria.

(iii) Figure 7 illustrates the rare case in which a runway threshold is preceded by an aligned taxiway. In this case yellow arrowheads without arrow shafts are required to identify the runway portion from the aligned taxiway portion.

General Comment Airport operators should avoid the (1) conversion of a runway section into an aligned taxiway and (2) construction of a new aligned taxiway.

(2) Locations.

(i) For the predominant case, arrow shafts and arrowheads are located on the portion of the runway before the displaced threshold.

(ii) For the rare cases, only arrowheads are used on the portion of the aligned taxiway before the threshold bar marking or the demarcation bar marking.

(3) Colors.

(i) For the predominate case, the arrow shaft and arrowhead are white. See paragraph 1.4 for required and recommended techniques to enhance these markings. (ii) For the rare cases, the arrowhead is yellow.

(4) Characteristics. The dimensions and spacing requirements for arrow shafts and arrowheads are as shown in figure 6 (function one), figure 7 (function two), and figure 9 (function three).

c. Runway Demarcation Bar Marking.

(1) Purpose. A demarcation bar delineates a runway with a displaced threshold from a blast pad, stopway, or an aligned taxiway that precedes the runway.

(2) Location. The demarcation bar is an elongated rectangular bar on a blast pad, stopway, or an aligned taxiway that is perpendicular to the runway centerline at the point of intersection with the start of the runway as shown in figure 10. In another application, as shown in figure 9, the portion of aligned taxiway before the demarcation bar is not part of the usable runway.

(3) Color. The demarcation bar marking is yellow. See paragraph 1.4 for required and recommended techniques to enhance this marking.

(4) Characteristics. The demarcation bar marking is 3 feet (0.9 m) wide and extends across the entire width of the blast pad, stopway, or aligned taxiway.

CHAPTER 2. SURFACE MARKINGS FOR RUNWAYS. › 2.11. RUNWAY SHOULDER MARKING.

2.10. CHEVRON MARKINGS FOR BLAST PADS, STOPWAYS, AND EMAS.

a. Purposes. The chevron marking identifies paved blast pads, stopways, and EMAS (engineered materials arresting systems) in relation to the end of the runway. For lighting provisions, see AC 150/5340-30, and for EMAS design, see AC 150/5220-22, Engineered Materials Arresting Systems for Aircraft Overruns.

b. Location. The chevron marking is located on the blast pad and stopway that are aligned with and contiguous to the runway end as shown in figures 8 and 10. The chevron scheme for an EMAS installation is also centered along the extended runway centerline (not shown in figures 8 and 10).

c. Color. Chevron markings are yellow. See paragraph 1.4 for required and recommended techniques to enhance this marking.

d. Characteristics. Dimensionally, stopways equal the width of the runway while blast pads equal the runway width plus the shoulder widths (see AC 150/5300-13). The dimensions and spacing requirements for chevron markings are shown in figure 8. The recommended minimum length for a stopway is 150 feet (45.7 m) to allow for at least two chevron stripes. For cases where (1) standard length blast pads, per AC 150/5300-13, are installed off runway ends used exclusive by small airplanes (Airplane Design Group I – small) or (2) existing stopways are less than 150 feet (45.7 m) in length on runway widths of 75 feet (22.9 m) or less, the width of the chevrons and the spacing between the chevrons shown in figure 8 can be reduced by two-thirds. The intent of the reduction in dimensions is to provide pilots with at least two visible chevrons. 2.11. RUNWAY SHOULDER MARKING.

a. Purpose. The runway shoulder marking is used, when needed, as a supplement to further delineate a paved runway shoulder that pilots have mistaken or are likely to mistake as usable runway. This marking is used only in conjunction with the runway side stripe marking.

b. Location. The runway shoulder marking is located between the runway side stripe and the outer edge of the paved shoulder as shown in figure 11.

c. Color. Runway shoulder markings are yellow. See paragraph 1.4 for required and recommended techniques to enhance this marking.

d. Characteristics. The runway shoulder marking consists of stripes 3 feet (0.9 m) in width and spaced 100 feet (30.5 m) apart along the edge of the runway. The stripes start at the runway midpoint, are slanted at an angle of 45 degrees to the runway centerline, and are oriented as shown in figure 11.

Blank Page

CHAPTER 3. HOLDING POSITION MARKINGS. › 3.2 CASE 1 AND CASE 2 – APPLICATIONS OF PATTERN A FOR THE RUNWAY…

CHAPTER 3. HOLDING POSITION MARKINGS. 3.1. APPLICATIONS OF HOLDING POSITION MARKINGS. The purposes for the different holding position markings are to prevent aircraft and vehicles from entering into critical areas associated with a runway and navigational aids or to control traffic at the intersection of taxiways. This advisory circular describes six operational situations (cases) using three different holding position marking schemes. Cases 1, 2, and 3 employ the same marking scheme referred to as Pattern A – runway holding position marking. Cases 4 and 5 employ a different marking scheme referred to as Pattern B – ILS/MLS or POFZ holding position marking. The latter operational situation, Case 5, uses Pattern B in which it usually appears as an L-shaped ladder. Case 6 uses a different marking scheme referred to as Pattern C – intermediate holding position marking for taxiway/taxiway intersections. Figures 12 and 12a show the four different marking patterns.

 Case 1: In terms of taxiing on a runway, an aircraft will need to hold short of an intersecting

runway (see paragraph 3.2).

 Case 2: In terms of landing on a runway used for land and hold short operations (LAHSO), the

aircraft will need to hold short of an intersecting runway or, in some rare cases, at a specified hold spot on the landing runway (see paragraph 3.2).

 Case 3 (most common application for Cases 1, 2, and 3): In terms of taxiing on a taxiway, an

aircraft will need to hold short prior to entering an active runway (see paragraph 3.3).

 Case 4: In terms of taxiing on a taxiway, an aircraft will need to hold short before entering the

critical area of an Instrument Landing System (ILS)/Microwave Landing System (MLS) (see paragraph 3.4).

 Case 5: In terms of taxiing on a taxiway, an aircraft will need to hold short before entering the

critical area of a Precision Obstacle Free Zone (POFZ) (see paragraph 3.5). Although the surface marking pattern is the same as Case 4, the pattern in many applications is L-shaped, instead of only linear in shape.

 Case 6: In terms of taxiing on a taxiway, an aircraft will need to hold short of a taxiway/taxiway

intersection (see paragraph 3.6). 3.2 CASE 1 AND CASE 2 – APPLICATIONS OF PATTERN A FOR THE RUNWAY HOLDING POSITION MARKING ON RUNWAYS.

a. Purpose. Pattern A when painted on a runway, as shown in figure 12, identifies the location where a pilot (or vehicle driver) is to stop and hold when (1) the runway is operationally closed for an interval of time so that ATCT can control taxiing operations through a runway/runway intersection or (2) the runway is used for land and hold short operations (LAHSO). For necessary corresponding signage and lighting provisions, see AC 150/5340-18, Standards for Airport Sign Systems, and AC 150/5340-30, Design and Installation Details for Airport Visual Aids.

AC 150/5340-1K Change 1 11/17/2010

Safety Initiatives

(Safety) Note 1: Land and hold short operations (LAHSO) require a letter of agreement between the airport operator and the airport traffic control tower (ATCT). Note 2: Paragraph 405, Parallel Taxiway, of AC 150/5300-13 states that a basic airport consists of a runway with a full-length parallel taxiway. Since the design standard for a fulllength parallel taxiway reduces both wrong-runway takeoffs and runway incursions, we do not recommend the use of an operationally closed runway as a taxiway, especially when a parallel taxiway exists. Such an operation can potentially confuse pilots because this taxiing operation introduces yellow-colored taxiway surface markings onto the runway itself. Hence, to avoid the potential for operational errors by pilots, the airport operator should take measures to meet the full-length parallel taxiway design standard. In some cases, the operational capacity for a given runway could indicate the need for dual parallel taxiways to avoid this type of taxiing operation. Note 3: To avoid a runway incursion event at runway/runway intersections when an operationally closed runway is used as a taxiway, the intersection must have the runway holding position marking and corresponding signs whether or not pilots taxi through the runway/runway intersection. Additionally, this marking should only be used in those instances where documentation supports the need for the operational use of the runway as a taxiway. The operational use of a runway as a taxiway must be described in a Letter of Agreement with the ATCT.

b. Location. In all Case 1 and Case 2 applications, the location of the runway holding position marking is at or beyond the edge of the runway safety area of the intersecting runway as provided by AC 150/5300-13. The criteria given below assume that the centerlines of the intersecting runways are perpendicular. Hence, for runway/runway intersections that are non-perpendicular, additional distance may be required to ensure that all airplane features, such as wingtips, remain outside the runway safety area of the intersecting runway.

(1) Operationally Closed Runways Used for Taxiing Operations. The location of the runway holding position marking on operationally closed runway is in accordance with the holdline criteria per table 2-1 or table 2-2 in AC 150/5300-13 for the intersecting runway’s airport reference code.

(2) Runways Used for LAHSO.

(i) The location of the runway holding position marking on the runway used for LAHSO is in accordance with the holdline criteria per table 2-1 or table 2-2 in AC 150/5300-13 for the intersecting runway’s airport reference code. On rare cases the location of the runway holding position marking for LAHSO is based on a predetermined hold-short point along the landing runway to protect an approach/departure flight path or to overcome painting difficulties as described below in subparagraph 3.2(b)(2)(ii). In no case should the location of the predetermined hold-short point be within the holdline criteria in table 2-1 or table 2-2 in AC 150/5300-13 for the intersecting runway’s airport reference code.

(ii) Certain airfield geometries for runways that are used for taxiing or LAHSO operations have intersecting taxiway(s) that hamper the painting of the runway holding position marking (and accompanying necessary signage) in accordance with the applicable holdline criterion. One such geometry occurs when a crossing taxiway or its fillet intersects the same area indicated by table 2-1 or table 2-2 of AC 150/5300-13. One solution is to move the hold-short point further away from the

CHAPTER 3. HOLDING POSITION MARKINGS. › 3.3. CASE 3 – APPLICATIONS OF PATTERN A FOR THE RUNWAY HOLDING POSITION…

runway/runway intersection so that both the marking and the installed signage clear the common crossing area. Under this solution (1) the marking is always painted at a greater distance than the holdline criteria in table 2-1 or table 2-2 of AC 150/5300-13 based on the intersecting runway, not the cleared taxiway, and (2) the required corresponding signage retains only the runway designations, i.e., never uses a taxiway designation.

c. Color. The Pattern A marking scheme, as shown in figure 12, is yellow and, when painted on light-colored pavements, is outlined in black. See paragraph 1.4 and table 1-1 for required and recommended techniques to enhance this surface marking on light-colored pavements.

d. Characteristics.

(1) The marking is identical to the runway holding position marking installed on a taxiway as described in paragraph 3.3 and shown in figure 12. The solid lines, as compared to the dash lines, are always on the side where the aircraft is to hold.

(2) The marking is installed perpendicular to the runway centerline and interrupts all runway markings except for the runway designation marking. If the runway holding position marking should interrupt the mentioned exceptions, then paint the runway holding position marking further away than specified by AC 150/5300-13 to avoid any interruption of these specified markings. The painting practice is to avoid “over striping” existing runway surface markings.

(3) The runway holding position marking extends across the full width of the runway but not onto the runway shoulders or onto any intersecting taxiway fillet. 3.3. CASE 3 – APPLICATIONS OF PATTERN A FOR THE RUNWAY HOLDING POSITION MARKING ON TAXIWAYS.

a. Purposes. Pattern A when painted on a taxiway as shown in figure 12 serves several roles. For a taxiway that intersects a runway at an airport with an operating airport traffic control tower (ATCT), the Pattern A marking scheme identifies the location on a taxiway where pilots and vehicle drivers are to stop until they receive a clearance from ATCT to proceed onto the runway. Under this role, Pattern A may be supplemented with the Geographic Position Marking as part of the airport’s Surface Movement Guidance Control System (SMGCS) Plan as described in paragraph 4.11 and as shown in figure C-8. For a taxiway that intersects a runway at an airport without an operating airport traffic control tower, Pattern A identifies the location where a pilot and vehicle drivers are to stop to ensure that they have adequate separation with other aircraft before proceeding onto the runway.

For a taxiway that does not intersect a runway but crosses through a runway approach area or the runway safety area, the Pattern A marking scheme identifies the location on a taxiway where pilots and vehicle drivers are to stop to receive clearance from the airport traffic control tower before proceeding through the protected area. This application serves to stop a taxiing aircraft from penetrating the runway safety area (a runway incursion) or any of several airspace surfaces, for example, those used to define the runway threshold, runway inner approach obstacle free zone, or the runway inner transitional obstacle free zone. If the marking is located closer than prescribed by AC 150/5300-13, such as when the taxiing aircraft penetrates a Terminal Instrument Procedures (TERPS) surface, then the airport operator can expect higher approach minimums to the impacted runway end. AC 150/5300-13 includes a discussion of these airspace surfaces.

Except as specified in paragraph 3.2, the runway holding position marking must not be used for any other situations than the roles described in this paragraph. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

AC 150/5340-1K Change 1 11/17/2010

b. Location. Pattern A for the runway holding position marking is located as follows.

(1) For a taxiway that intersects a runway, the Pattern A runway holding position markings must be located on all such taxiways in accordance with the holdline criteria per table 2-1 or table 2-2 in AC 150/5300-13 for the runway’s airport reference code. Since the location is based on the approach visibility minimums, approach category, and airplane design group, the airport operator should use the lowest approach visibility minima and critical aircraft intended to use the runway. Pattern A is used also on turnarounds and holding bays as shown in figures 4-8 and 4-9 of AC 150/5300-13, especially for airports with an airport traffic control tower or for any runways used at night and in low-visibility conditions. Locating a runway holding position marking other than what is required by this paragraph must be approved by the FAA.

(2) For a taxiway not intersecting a runway but crossing through a runway safety area or a runway approach surface, the Pattern A runway holding position markings must be located on all such taxiways in accordance with the more protective area obtained by either the holdline criteria per table 2-1 or table 2-2 in AC 150/5300-13 for the runway’s airport reference code or the boundary of the approach surface’s critical area. The Pattern A marking must extend across the entire width of the taxiway. Locating a Pattern A runway holding position marking other than what is required by this paragraph must be approved by the FAA Airports Regional Office or Airports District Office.

(3) The Pattern A marking must extend across the entire width of the taxiway. For taxiways having taxiway edge markings, discontinue the taxiway edge marking as shown in figure 21 so that the Pattern A marking continues to the edge of the defined taxiway width. For taxiways that serve Airplane Design Groups (ADG) V or VI airplanes as defined by AC 150/5300-13, the marking is further extended onto both paved shoulders as shown in figure C-4. For both airplane design groups, the length of the marking from the taxiway centerline onto the paved shoulder measures 62.5 feet (19 m). The 62.5-foot (19-m) measurement takes into account the downward viewing angle from the cockpit while the pilots are seated in the normal position as well as other safety factors, such as aircraft wander from the taxiway centerline. For taxiways with widths greater than 75 feet (22.9 m), the runway holding position marking is extended 25 feet (7.5 m) [62.5 viewing angle minus (1/2)(75) standard taxiway width equals 25 feet] onto the paved taxiway shoulders. Only those taxiway entrances to a runway that serve ADGs V or VI are to be further enhanced. Typical airplane models within ADGs V and VI include the Airbus 330-200/- 300, A-340-200/-300/-500/-600, A-380, Boeing-747-100/-200/-400, B-777-200/-300, and B-787-8/-9.

14 Code of Federal Regulation (CFR) Part 139 Certificated Airports Runway Incursion Mitigation Requirement

(Safety) The extended runway holding position marking, as illustrated in figure C-4, is mandatory and is the only acceptable means of compliance for 14 CFR Part 139 certificated airports serving ADGs V and VI airplanes. The enhanced runway holding position marking applies only to those taxiway entrances for a given runway that serve these airplane design groups. Since the compliance date of June 30, 2008, has passed, all new taxiway entrances serving ADGs V and VI airplanes must be painted accordingly prior to opening the taxiway. This surface painted marking is part of the taxiway centerline marking standard under 14 CFR Section 139.311(a)(2). c. Color. The Pattern A marking scheme, as shown in figure 12, is yellow and, when painted on light-colored pavements, outlined in black. See paragraph 1.4 and table 1-1 for required and recommended techniques to enhance this surface marking.

CHAPTER 3. HOLDING POSITION MARKINGS. › 3.4. CASE 4 – APPLICATIONS OF PATTERN B FOR THE ILS/MLS HOLDING…

d. Characteristics. Pattern A for the runway holding position marking consists of a set of two continuous lines, two dashed lines, and three spaces that are all parallel, run the width of the paved taxiway, measure 12 inches (30 cm) in width, and are separated as shown in figure 12. At airports that do not have an operating ATCT and are not certificated under 14 CFR Part 139, the width and separation measurement may be reduced from 12 inches (30 cm) to 6 inches (15 cm). For clarification, all airports certificated under 14 CFR Part 139, whether or not there is an operating ATCT, are required to use the 12-inch measurement.

(1) The orientation of Pattern A is for the solid continuous lines to be painted on the side where the aircraft and vehicles will hold before proceeding to the runway. That is, dashed lines are painted closer to the runway.

(2) Pattern A is painted perpendicular to the taxiway centerline but may be canted from the perpendicular in unique situations, such as an extremely acute, angled taxiway. For such unique situations, it may be necessary to install additional runway holding position signs, runway guard lights, or stop bars to emphasize the location of the surface painted runway holding position marking.

(3) Pattern A on converging taxiways as shown in figure C-13 meet at an angle when two or more taxiways intersect the same runway hold line. On any angled taxiway to the runway, consideration must be given to locate the painted marking so no portion of an aircraft, e.g., wing tip or tail, penetrates the runway safety area or any protected surface. See AC 150/5300-13 for detailed requirements and information about clearance requirements by aircraft on taxi routes.

(4) For taxiways with taxiway edge markings, the taxiway edge markings must be removed for the width of the Pattern A marking.

(i) If the runway holding position marking is outlined in black, then the taxiway edge markings abut the black outline on both sides of this marking. That is, it abuts the black border of the solid yellow line on one side and abuts the black border of the dashed yellow line on the other side.

(ii) If the runway holding position marking is not outlined in black, then the taxiway edge markings abut the holding position marking on both sides. That is, the taxiway edge markings abut the solid yellow line on one side and abut the dashed yellow line on the other side.

(5) For ADGs V and VI taxiways having a light fixture or a sign located on the taxiway shoulder that aligns with the extended runway holding position marking, as shown in figure C-4, the extended runway holding position marking should extend no closer than 5 feet (1.5 m) to the edge of the light fixture or sign.

(6) For ADGs V and VI taxiways whose taxiway shoulder markings interfere with or are within 10 feet (3.1 m) from the extended runway holding position marking, as shown in figure C-4, are to be removed (omitted) from that location. 3.4. CASE 4 – APPLICATIONS OF PATTERN B FOR THE ILS/MLS HOLDING POSITION MARKING.

a. Purposes. Pattern B for the ILS/MLS holding position marking as shown in figure 12 identifies the location on a taxiway or holding bay where a pilot or vehicle driver is to stop when they have received instructions from the airport traffic control tower (ATCT) to hold before entering an ILS/MLS critical area. The intent of the marking is to protect the signal of the ILS/MLS navigational aid

CHAPTER 3. HOLDING POSITION MARKINGS. › 3.5. CASE 5 – APPLICATIONS OF PATTERN B FOR PRECISION OBSTACLE FREE…

by identifying the holding position for CAT I operations and protecting the approved TERPS for CAT II/III operations. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

b. Location. Pattern B for the ILS/MLS holding position marking is located on the taxiway or holding bay at the boundary of the ILS/MLS critical area and, as appropriate, at the holding position for CAT I and CAT II/III operations.

(1) Where the distance between an ILS/MLS holding position (Pattern B) marking and the runway holding position (Pattern A) marking on a taxiway is 50 feet (15 m) or less, paint only one pattern, provided it will not adversely affect capacity. In this case, it is preferable to move the runway holding position (Pattern A) marking back to the where the ILS/MLS holding position (Pattern B) would have been painted. This preference is selected for taxiways serving ADG V or ADG VI airplanes in which the marking is extended onto the taxiway shoulders.

(2) If a taxiway or holding bay penetrates both an ILS/MLS critical area and the Precision Obstacle Free Zone (POFZ) critical area (see Pattern B, figure 12a), such as when the threshold is displaced, paint only one pattern instead of two patterns only if the single pattern can protect both critical areas. The pattern to be painted is the one whose location offers the most conservative, protective boundary (for example, farthest from the runway).

(3) The FAA Airports Regional Office or Airports District Office will designate the ILS/MLS critical area and POFZ boundaries and, as appropriate, determine the correct holding position location for CAT II/III operations for the airport operator. See AC 150/5300-13 for general information about the ILS/MLS and POFZ critical areas.

(4) The Pattern B marking for ILS/MLS applications must extend across the entire width of the taxiway or holding bay as shown in figure 12.

c. Color. The Pattern B marking scheme as shown in figure 12 is yellow and, when used on light-colored pavements, outlined in black. See paragraph 1.4 and table 1-1 for required and recommended techniques to enhance this surface marking.

d. Characteristics. Pattern B for the ILS/MLS holding position marking consists of a set of two parallel lines that are 2 feet (0.6 m) wide and spaced 4 feet (1.2 m) apart. These parallel lines are connected by perpendicular sets of two lines that are 1 foot (0.3 m) wide and spaced 1 foot (0.3 m) apart and repeat every 10 feet (3 m) (see Figure 12). Figure 12 provides the discontinuation (separation) of an ILS/MLS holding position marking with an intersecting taxiway centerline or taxiway edge stripe markings. At airports that do not have an ATCT and are not certificated under 14 CFR Part 139, the airport operator may reduce the dimension for the width of the parallel yellow lines and spaces from 2 feet (0.6 m) to 1 foot (0.3 m) and from 4 feet (1.2 m) to 2 feet (0.6 m). For clarification, all airports certificated under 14 CFR Part 139, whether or not there is an operating ATCT, are required to use the larger measurements.

3.5. CASE 5 – APPLICATIONS OF PATTERN B FOR PRECISION OBSTACLE FREE ZONE (POFZ) HOLDING POSITION MARKING.

a. Purposes. Pattern B for the POFZ holding position marking as shown in figure 12a identifies the location on a taxiway or holding bay where a pilot or vehicle driver is to stop when they have received instructions from the airport traffic control tower (ATCT) to hold before entering the POFZ critical area. The marking is used also at non-towered airport where the runway end has an approved vertical guidance

CHAPTER 3. HOLDING POSITION MARKINGS. › 3.6. CASE 6 – APPLICATIONS FOR PATTERN C FOR THE TAXIWAY/TAXIWAY…

of ¾-statue mile approach visibility minimum or less. The intent of the marking is to protect the authorized landing minima (TERPS) for a given runway end. See AC 150/5300-13 for detailed information about the POFZ critical area. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

b. Location. Pattern B for the POFZ holding position marking is located on the taxiway or holding bay at the boundary of the POFZ critical area as defined by AC 150/5300-13 and, when appropriate, at the holding position for CAT I and CAT II/III operations. Figure 15 shows the most common application for this marking which is L-shaped. Because of the variety of taxiway entrance/holding bay geometries, the Pattern B marking must not be painted over a surface painted holding position sign.

(1) Certain airfield geometries may cause a taxiway or holding bay to penetrate both an ILS/MLS critical area and the Precision Obstacle Free Zone (POFZ) critical area, such as when the threshold is displaced. Under such situations, paint only one pattern instead of two patterns only if the single pattern can protect both critical areas. The pattern to be painted is the one whose location offers the most conservative, protective boundary (for example, farthest from the runway). Under this application the ILS/MLS holding position (Pattern B) marking or POFZ holding position (Pattern B) marking, which now serves a dual function, cannot be replaced with, or used in lieu of, a runway holding position (Pattern A) marking.

(2) The FAA Airports Regional Office or Airports District Office will designate the ILS/MLS critical area and POFZ boundaries and, as appropriate, determine the correct holding position location for CAT II/III operations for the airport operator.

(3) The Pattern B marking for POFZ applications must extend across only those portions of a taxiway or holding bays that run along the boundary of the POFZ as shown in figures 12a and 15.

c. Color. The Pattern B marking scheme is yellow and, when used on light-colored pavements, outlined in black. See paragraph 1.4 and table 1-1 for required and recommended techniques to enhance this surface marking.

d. Characteristics. Pattern B for the POFZ holding position marking consists of a set of two parallel lines that are 2 feet (0.6 m) wide and spaced 4 feet (1.2 m) apart. These parallel lines are connected by perpendicular sets of two lines that are 1 foot (0.3 m) wide and spaced 1 foot (0.3 m) apart and repeated every 10 feet (3 m). Figure 12, provides the discontinuation (separation) of a POFZ holding position marking, which follows the same criteria as the ILS/MLS holding position marking, with an intersecting taxiway centerline or taxiway edge stripe markings. Figure 15 illustrates the general separation of a Pattern B marking from an entrance taxiway serving a runway. At airports that do not have an ATCT and are not certificated under 14 CFR Part 139, the airport operator may reduce the dimension for the width of the parallel yellow lines and spaces from 2 feet (0.6 m) to 1 foot (0.3 m) and from 4 feet (1.2 m) to 2 feet (0.6 m). For clarification, all airports certificated under 14 CFR Part 139, whether or not there is an operating ATCT, are required to use the larger measurements.

3.6. CASE 6 – APPLICATIONS FOR PATTERN C FOR THE TAXIWAY/TAXIWAY INTERSECTION INTERMEDIATE HOLDING POSITION MARKING.

a. Purpose. Pattern C for the intermediate holding position marking, as shown in figure 12a for taxiway/taxiway intersections, is used to support the operational need by the airport traffic control tower to manage taxiing aircraft through a congested intersection or for other reasons deemed necessary by the

FAA. For example, figure 14 shows the intersection between a taxiway and a holding pad used for deicing aircraft. Pilots when instructed by the airport traffic control tower to "hold short of (taxiway designation)" must stop so no part of the aircraft extends beyond the boundary of the intermediate holding position marking. For signage and lighting provisions, see AC 150/5340-18 and AC 150/5340-30.

b. Location. For the taxiway being marked, the intermediate holding position marking for taxiway/taxiway intersection is located according to the taxiway centerline to fixed or movable object criteria in table 2-3 of AC 150/5300-13 for the most demanding airplane design group serving the airport (as defined in AC 150/5300-13).

c. Color. The intermediate holding position marking is yellow and, when used on light-colored pavements, outlined in black. See paragraph 1.4 and table 1-1 for required and recommended techniques to enhance this surface marking.

d. Characteristics. The intermediate holding position marking for taxiway/taxiway intersections consist of a single dashed line extending across the width of the taxiway per figure 12a and figure B-7. The single dash lines are 1 foot (0.3 m) wide, 3 feet (0.9 m) long, and spaced 3 feet (0.9 m) apart. As shown in figure 12a, all intersecting taxiway centerlines are spaced 6 to 12 inches (15 cm to 30 cm) on either side of this marking.

CHAPTER 4. SURFACE MARKINGS FOR TAXIWAYS. › 4.2. TAXIWAY CENTERLINE MARKINGS.

11/17/2010 AC 150/5340-1K Change 1

CHAPTER 4. SURFACE MARKINGS FOR TAXIWAYS.

4.1. APPLICATION. All taxiways regardless of their width have a centerline marking, and whenever a taxiway intersects a runway, the taxiway should have a surface painted runway holding position marking. For 14 CFR Part 139 certificated airports, all taxiways that intersect a runway must have a surface painted runway holding position sign(s) and an enhanced taxiway centerline marking. Taxiway edge markings are installed wherever there is a need to separate the taxiway from a pavement that is not intended for aircraft use or to delineate the edge of the taxiway that is not otherwise clearly visible. Examples of other taxiway surface markings that should be installed when appropriate and deemed necessary by the FAA (in some cases, with input from the tower manager of the airport traffic control tower (ATCT)) include the Pattern A, B, and C holding position markings discussed in Chapter 3, the intermediate holding position markings for taxiway/taxiway intersections, geographic position marking, and the taxiway shoulder marking. 4.2. TAXIWAY CENTERLINE MARKINGS. All taxiways regardless of their width have a surface painted taxiway centerline.

a. Purpose. The taxiway centerline marking provides pilots continuous visual guidance to permit taxiing along a designated path. See AC 150/5300-13 for standard fillet design, AC 150/5340-30 for lighting provisions and AC 150/5340-18 for signage provisions.

b. Location. On a straight section of a taxiway, the taxiway centerline marking is located along the physical centerline of the paved taxiway. This statement assumes the taxiway was built to standard, i.e., symmetrical with a taxiway centerline. On curved sections of a taxiway, the taxiway centerline marking continues from the centerline marking of the straight portion of the taxiway along a curved centerline defined as the Radius of Taxiway Turn in table 4-2 of AC 150/5300-13.

(1) For taxiways that intersect other taxiways, the adequacy of the fillet design determines the centerline painting scheme as shown in figure 16. The recommended design is cockpit-overcenterline steering which reduces the number of airplane main gear excursions from the taxiway.

(i) At taxiway intersections with fillets that do not meet the fillet design standards of AC 150/5300-13—that is, judgmental over-steering is performed by pilots—the centerline marking continues straight through the intersection as shown at the top of figure 16. This practice applies to intersecting taxiways that are or are not of the same airport reference code.

(ii) Where adequate fillets exist, that is, the fillets are designed to the most demanding aircraft, the taxiway centerline marking follows the taxiway curve as shown on the bottom of figure 16 to permit cockpit-over-centerline steering operations. This practice applies to intersecting taxiways that are or are not of the same airport reference code.

Note: AC 150/5300-13 states that cockpit-over-centerline steering as compared to judgmental over-steering is the preferred methodology for painting taxiway centerlines in taxiway intersections. To reduce taxiway excursions on turns, airport operators are encouraged to (1) construct standard fillets and (2) paint taxiway centerlines according to cockpit-over-centerline design.

(2) For taxiways that intersect runways, different painting requirements or restrictions apply.

(i) For a taxiway that intersects a runway at a runway end, as shown in figures 14 and 15, the taxiway centerline is terminated either at the runway edge or at the outer edge of the runway side stripe. However, the taxiway centerline (lead-on and lead-off) will continue onto the runway under the following conditions:

(1) Where there is a displaced threshold, as shown in figures 6 and 10, the taxiway centerline marking continues onto the displaced area of the runway and extends parallel to the displaced threshold markings (arrow heads and arrow shafts) for a distance of 200 feet (61 m) beyond the point of tangency or terminates at the point of contact with the displaced threshold bar, whichever is less. As shown in figure 6 the lead-on and lead-off taxiway centerlines are 3 feet (1 m) from the runway arrow markings as measured near-edge to near-edge. This lead-on or lead-off taxiway centerline line is interrupted for all runway markings with some exceptions (see paragraph 4.2(b)(2)(i)(2)).

Continue reading ↓ 120 of 240 passages shown