84 FR 15296 Streamlined Launch and Reentry Licensing Requirements
This rulemaking would streamline and increase flexibility in the FAA's commercial space launch and reentry regulations, and remove obsolete requirements. This action would consolidate and revise multiple regulatory parts and apply a single set of licensing and safety regulations across several types of operations and vehicles. The proposed rule would describe the requirements to obtain a vehicle operator license, the safety requirements, and the terms and conditions of a vehicle operator license.
This document is proposed. It may have been replaced. Check the official source before relying on it.
iii. Separation Distance Calculations by Sphere or Ellipsoid
Similarly, although launch incidents and reentry incidents are both incidents, their definitions consist of different requirements. Launch and reentry incidents occur due to the malfunction of a FSS or other safety-critical system, or a failure of the operator's safety organization, design or operations. The FAA proposes to consolidate these terms into a single mishap classification system eliminating the need for multiple terms.
Current definitions of mishap and accident also include a $25,000 monetary threshold that is arbitrary and outdated. Experience has shown that even minor damage that does not pose a threat to public safety can easily exceed the $25,000 monetary threshold, triggering potentially costly and burdensome notification, reporting, and investigation requirements. For example, a relatively minor unplanned event following a successful launch could result in damages to ground support equipment or launch facilities exceeding $25,000. The ARC noted the amount is outdated and does not necessarily reflect safety implications. Additionally, the conditions listed under the current definitions do not necessarily reflect the severity of consequences and associated public safety risks. A better mishap classification system would provide consistency of mishap thresholds and applicability to all types of operations, mitigating potential confusion. Rather than adding more definitions, the FAA would consolidate and replace the existing accident, incident, and mishap definitions with a mishap classification system that would be defined in § 401.5 and would apply to all licensed and permitted activities.
Under the proposed changes, "mishap" would mean any event, or series of events associated with a licensed or permitted activity, that meets the criteria of a Class 1, 2, 3 or 4 mishap. The FAA would use this overarching definition to describe any mishap type occurring during permitted or licensed activities regardless of classification or consequence threshold. The FAA's proposal was informed by existing NASA and Air Force mishap classification system definitions,\141\ and NTSB definitions.\142\
\141\ NPR 8621.1C, NASA Procedural Requirements for Mishap and Close Call Reporting, Investigating, and Recordkeeping. Air Force Instruction 91-204, Safety Investigation and Hazard Reporting.
\142\ As defined in 49 CFR 830.2.
A "Class 1 mishap" would mean any event resulting in a fatality or serious injury to any person who is not associated with the licensed or permitted activity (e.g., members of the public) along with any space flight participant, crew, or government astronaut. The FAA would be adopting the definition of fatality or serious injury from 49 CFR 830.2. To constitute a Class 1 mishap, the fatality or injury must result from licensed or permitted activity, including ground operations at a launch or reentry site. A Class 1 mishap would be a mishap that has the highest consequences and greatest impact on public safety. The proposed Class 1 mishap definition would incorporate existing fatality and serious injury criteria from current "launch accident," "reentry accident" and "launch site accident" definitions.
On November 25, 2015, the U.S Commercial Space Launch Competitiveness Act was signed into law (Pub. L. 114-90). This law amends 51 U.S.C. 50901(15) by inserting "government astronauts" after "crew" each place it appears. In accordance with this amendment, and to ensure Class 1 mishap criteria applies equally to all persons on board a launch or reentry vehicle, the FAA Class 1 mishap definition includes government astronauts. The definition would only cover fatalities or serious injuries to crew, Government astronauts, spaceflight participants, or uninvolved public. The definition of Class 1 mishap would not cover other persons associated with the launch or reentry, similar to the current accident definitions for which it replaces. The proposed Class 1 Mishap also consolidates existing accident definitions, which would include potential recovery site accidents that were previously not defined. The FAA proposes to define a "Class 2 mishap" as any unplanned event, other than a Class 1 mishap, resulting in a malfunction of a safety-critical system, a failure of the safety organization or procedures, substantial damage to property not associated with the operation, or a high risk of causing a serious or fatal injury to any space flight participant, crew, government astronaut, or member of the public. The Class 2 mishap definition would encompass the current definitions of a "launch incident," "reentry incident," and "human space flight incident." The definition would use a substantial damage to uninvolved property requirement instead of the $25,000 damage threshold.
Under this proposal, the FAA would make a case-by-case determination whether the damage to public property is substantial. This evaluation may be based on, but not limited to, direct replacement cost, repair cost, and the property's intended use and functionality. For example, structural damage to public property exceeding 50 percent of its market value may be deemed as substantial damage. This approach potentially reduces the burden on the commercial space industry and Federal government by providing flexibility on the determination of substantial damage and the scope of the resulting investigation. This is consistent with the ARC feedback. Other criteria--such as events posing a high risk of causing a serious or fatal injury to any space flight participant, crew, government astronaut, or member of the public--are based on the existing "human space flight incident" definition and expanded to include government astronauts and members of the public. With this criterion, the FAA intends to cover events akin to a near miss in the aviation industry and is consistent with the Air Force and NASA practices. The addition of "members of the public" is consistent with the FAA's public safety mission. The FAA's goal is to evaluate the event type by impact to public safety.
The FAA proposes to define "Class 3 mishap" as any unplanned event, other than a Class 1 or Class 2 mishap, resulting in permanent loss of a vehicle during licensed activity or the impact of a vehicle, its payload, or any component thereof outside the planned landing site or impact area. This change would differentiate between licensed launches and reentries and permitted launches and reentries. The FAA believes this proposal captures the intent of the current mishap definition that includes the failure to complete a launch or reentry as planned criterion. At the same time, the separation of licensed and permitted operations between Class 3 and 4 mishaps is also consistent with ARC feedback.
The FAA would consider debris impacts outside of defined limits to meet the Class 3 mishap definition, provided the event did not satisfy the criteria of a Class 1 or 2 mishap. Impacts of launch vehicle debris outside designated impact limit lines are currently considered a launch accident.
The FAA proposes to define a "Class 4 mishap" as an unplanned event, other than a Class 1, Class 2, or Class 3 mishap, resulting in permanent loss of a vehicle during permitted activity, a failure to achieve mission objectives, or substantial damage associated with licensed or permitted activity. The FAA intends proposed "Class 4 Mishap" to capture other events with the potential for future public safety implications without directly affecting public safety during occurrence. For example, an operator may have complete loss of a permitted vehicle in a remote and unpopulated area. Although the loss may not have resulted in fatalities, serious injuries, or public property damage on this occasion, it is important to find the root cause of the mishap. Otherwise, if the operator does not identify and address the underlying cause, it may endanger public safety during a future launch in different conditions. ii. Anomaly Definition
The FAA proposes to change the definition of "anomaly" and to move the definition to § 401.5, where it would apply to all of chapter III. Anomaly would mean any condition during a licensed or permitted activity that deviates from what is standard, normal, or expected, during the verification or operation of a system, subsystem, process, facility, or support equipment. The inclusion of anomaly in § 401.5 would clearly define the expectation of post-operation reporting for all licensed or permitted operations. It would also capture off-nominal events that do not fall under the thresholds of Class 1-4 mishaps as part of the required post-launch report.
The FAA currently defines anomaly only in part 437. Part 437 defines an anomaly as a problem that occurs during verification or operation of a system, subsystem, process, facility, or support equipment. Section 437.73 requires strict recording, reporting, and implementation of corrective actions in the event of a public safety related anomaly. Section 417.25(c)(1), applicable to ELVs, requires operators to report an anomaly that occurred during launch countdown and flight in the post-launch report but does not define anomaly. Although part 431 does not have specific anomaly reporting requirements, in practice, the FAA requires operators to report anomalies. To ensure anomaly reporting, the FAA has begun adding a term and condition to launch licenses requiring operators to report anomalies prior to the next launch. The FAA uses anomaly reporting to track vehicle-related issues and to ensure an operator mitigates those issues prior to future flights. Given that not all anomalies are identified during flight, the post-launch reporting requirement allows the operator to review countdown and flight data for off-nominal conditions and report any anomalous condition to the FAA as a part of the post-launch report.
Although an anomaly is defined in § 437.3, as "a problem that occurs during verification or operation of a system, subsystem, process, facility, or support equipment," it is not defined in part 415, 417, 431, or 435, and hence, it is applicable only to experimental permits. However, § 417.25--Post launch report, requires an operator to "identify any discrepancy or anomaly that occurred during the launch countdown or flight." The FAA is proposing to update the existing definition of an anomaly to "any condition during a licensed or permitted activity that deviates from what is standard, normal, or expected, during the verification or operation of a system, subsystem, process, facility, or support equipment." The proposed definition seeks only to clarify what a "problem" is by adding "deviates from what is standard, normal, or expected." iii. Mishaps--Reporting, Response, and Investigation Requirements
The FAA proposes to consolidate current chapter III mishap plan, reporting, response and investigation requirements into proposed § 450.173. The FAA seeks comment on its proposed approach, as discussed below, to mishap requirements, including reporting.
Current title 14 CFR chapter III requirements for mishap and accident reporting, response, and investigation requirements are inconsistent and create confusion. For that reason, the FAA's proposed changes would apply to mishap requirements for launch and reentry licenses, experimental permits, and launch and reentry site licenses. Proposed § 450.173 would replace Sec. § 417.111(h) (Accident Investigation Plan), 417.415(c) (Post launch and post flight hazard controls), and 431.45 (Mishap investigation plan and emergency response plan). The proposed mishap plan changes to Sec. § 420.59(a) (Mishap) and 437.41 (Mishap plan) would require an operator to meet the requirements of § 450.173.
The inconsistencies in the FAA's current regulatory scheme, including signature requirements for mishap plans, has led to much confusion. For example, § 417.111(h) requires an operator to implement a plan containing the launch operator's procedures for reporting and responding to launch accidents, launch incidents, or other mishaps. It also requires two signatures, one from an individual authorized to sign and certify the application, and another from the designated safety official. Similarly, § 420.59 requires that licensed launch site operators develop and implement a launch site accident investigation plan that contains the licensee's procedures for reporting, responding to, and investigating launch site accidents and for cooperating with Federal officials in case of a launch accident. It also requires a signature from an individual authorized to sign and certify the application, but not from the designated safety official like § 417.111(h).
Current § 431.45 requires an RLV operator to submit a mishap investigation plan (MIP) containing the applicant's procedures for reporting and responding to launch and reentry accidents, launch and reentry incidents, or other mishaps that occur during the conduct of an RLV mission. It also requires that an RLV operator submit an emergency response plan (ERP) containing procedures for informing the affected public of a planned RLV mission. The FAA requires that an individual authorized to sign and certify the license application, the person responsible for the conduct of all licensed RLV mission activities, and the designated safety official, sign the MIP and ERP. In contrast, § 437.41 does not require any signatures. To ensure consistency between all title 14 CFR chapter III requirements, the FAA proposes to consolidate these requirements.
The ARC noted that reporting requirements for mishaps not involving a fatality or serious injury are unclear and left up to the operator to determine. The ARC said the FAA should define a minimum standard for a reportable mishap, in addition to a minimum set of investigation and reporting requirements, including information that should be provided during initial notification.
Current notification requirements are generally consistent for a launch, reentry, launch site accident, launch or reentry incident, or mishap involving a fatality or serious injury. In those instances, regulations throughout title 14 CFR chapter III require that operators provide immediate notification to the FAA's Washington Operations Center (WOC).\143\ This is not the case when a mishap does not involve a fatality or serious injury.\144\ For example, part 417 requires notification within 24 hours to the Associate Administrator for Commercial Space Transportation or to the FAA WOC in the event of a mishap that does not involve a fatality or serious injury. In contrast, parts 431 and 437 only require 24-hour notification to the Associate Administrator for Commercial Space Transportation, but not to the FAA WOC for a mishap that does not involve a fatality or serious injury. Current part 420 does not require a launch site operator to provide a 24-hour mishap notification. If a mishap occur during non-business hours, this raises the possibility that a launch operator may be unable to report it to the Associate Administrator for Commercial Space Transportation, which would create the potential for a non-compliance. To address these issues, the FAA proposes to provide a single source for all initial mishap notifications. The single source would be the FAA's WOC, a 24-hour, seven-day, operational facility.
\143\ 14 CFR 417.111(h)(1)(i), 420.59(b)(1), 431.45(b)(1), and 437.75(a)(1).
\144\ 14 CFR 417.111(h)(1)(ii), 431.45(b)(2), and 437.75(a)(2).
Parts 417, 420, 431, and 437 all require an operator to submit a written preliminary report within five days \145\ of either an accident or incident to the FAA, Associate Administrator for Commercial Space Transportation. The five-day report is a follow-up requirement designed to supplement initial mishap notification once more detailed information is known. Under the proposed mishap classification system and mishap plan requirements, all mishaps would have similar reporting requirements. The FAA believes the proposed mishap classification system would save the operator time and resources during the initial mishap response by eliminating the need to evaluate whether the event is an accident, incident, or mishap. This streamlining of reporting requirements reduces the burden of unclear reporting requirements noted by the ARC.
\145\ 14 CFR 417.111(h)(1)(iii), 420.49(b)(2), 431.45(b)(3), and 437.75(a)(3).
Based on past examples, the five-day report is usually only one to three pages in length, requiring minimal time to compose. The FAA will use the information contained within the five-day report to ensure the mishap has been properly classified and the proper level of investigation and FAA oversight is being conducted. The FAA believes the time required to complete the five-day report is minimal and that by providing a clear expectation of required report contents in the event of all mishap types will eliminate confusion and ultimately result in time-savings.
Response plan requirements for containing and minimizing the consequences of a mishap and for ensuring the preservation of data and physical evidence are generally consistent throughout license types with some exceptions. For instance, the regulations require that a launch site operator's plan include procedures for reporting and cooperating with FAA and NTSB investigations, and for designating one or more points of contact. Additionally, licensees must identify and adopt preventive measures for avoiding recurrence of the event.
Current investigation requirements are also generally consistent across license types. The FAA currently requires that operators investigate the cause of a launch, reentry, or launch site accident, launch or reentry site incident, or mishap across license types.\146\ After the investigation, an operator must report investigation results to the FAA and delineate responsibilities for personnel assigned to conduct the investigation and for anyone retained by the operator to participate in an investigation. Section 420.59(e)(1) also requires that a launch site operator's investigation plan include procedures for participating in an investigation of a launch accident for launches launched from the launch site.
\146\ 14 CFR 417.111(h)(3), 420.59(d)(3), 431.45(d), and 437.75(c).
To ensure vehicle recovery can be conducted safely and effectively and with minimal risk to the public, part 431 operators must submit an ERP containing the operator's procedures for notifying local officials of unplanned and offsite landings. In addition, these operators must provide a plan for informing the public potentially affected of the estimated date, time, and landing location for the reentry activity. This information must be provided in layman's terms. These requirements are unique to operations conducted under part 431.
Section 417.415(c)'s post-launch and post-flight-attempt hazard controls require that an operator establish procedural controls for hazards associated with an unsuccessful flight where the launch vehicle has a land or water impact. These procedures ensure the evacuation and rescue of members of the public, the dispersion and movement of toxic plumes, identifying areas of risk, and communication with local government authorities. Additionally, these procedures require that an operator extinguish fires, secure impact areas, evacuate members of the public, prevent unauthorized access, and preserve evidence. Lastly, the operator must ensure public safety from hazardous debris and have plans for the recovery, salvage, and safe disposal of debris and hazardous materials.
For all FAA-licensed operations, proposed § 450.173 would require that an operator report, respond, and investigate class 1, 2, 3, and 4 mishaps, using a plan or other written means.\147\
\147\ For purposes of the preamble discussion regarding proposed § 450.173, the term "mishap plan document" is used to encompass a plan or other written means.
An approved mishap plan document would be eligible for reuse with other specific or similar vehicles, sites, and operations. This would ease the burden on industry. For example, a permittee applying for a license or a current licensee applying for a different type of license, would be able to use the same written mishap plan document previously developed because the requirements would be the same regardless of license type. This mishap plan document would include notification to local officials should a mishap cause the vehicle to land offsite, such that a coordinated effort can be made to protect the public. Provided emergency response requirements such as coordinated emergency response agreements remain current, a permittee can submit a mishap response plan developed for permitted operations to satisfy the mishap plan document application requirements under a license. Additionally, the FAA would not have to evaluate the same company differently depending on the permit or license type. This would reduce time and cost for the industry and the FAA while maintaining the same level of public safety. iv. Discussion of the Mishap Plan--Reporting, Response, and Investigation Proposed Requirements
Proposed § 450.173 would eliminate all mishap plan signature requirements. The requirement that the person certifying the accuracy of the application also sign the mishap plan document is not necessary because by signing the application, the operator is already certifying that the components thereof, including the mishap plan document, are accurate. Additional signatures (e.g., from the safety official or mission director) are also unnecessary as the roles and responsibilities for personnel implementing the mishap plan document are contained in the plan itself. Eliminating the signature requirements would provide operators with the flexibility to assign personnel to implement a mishap plan document without having to resubmit a signed document to the FAA.
Proposed § 450.173(a) would require an operator to report, respond, and investigate class 1, 2, 3, and 4 mishaps according to paragraphs (b) through (h) of § 450.173, using a plan or other written means. Proposed § 450.173(b)(1) would require that an operator document the responsibilities for personnel assigned to implement the requirements of proposed § 450.173. Proposed § 450.173(b)(2) would require an operator to document reporting responsibilities for personnel assigned to conduct investigations and for anyone retained by the licensee to conduct or participate in investigations. Proposed § 450.173(b)(3) would require an operator to document the allocation of roles and responsibilities between the launch operator and any site operator for reporting, responding to, and investigating any mishap during ground activities at the site. Further, proposed § 450.173(c) would require an operator to report to, and cooperate with, FAA and NTSB mishap investigations. Also, it would require that the operator identify one or more points of contact for the FAA and NTSB.
This proposal does not substantively change current requirements to report, cooperate, and designate points of contact. Any changes from current regulations would be made merely for clarification purposes. In the event of an FAA- or NTSB-led investigation, the FAA would not require an operator to perform an independent internal investigation because it would be a party to the investigation. However, the operator would remain responsible for reporting investigation results to the FAA, which would include any government-generated or independent investigation reports as well as party submissions. In the event of an operator-led investigation under FAA oversight, the operator's investigation would be the primary investigation, although the FAA may grant official observer status to U.S. Government representatives (e.g., NASA, the Air Force). As official observers, these representatives would be integrated into the operator's investigation to the extent the FAA finds appropriate.
These U.S. Government entities may decide to conduct their own investigation independent of FAA oversight, although the FAA and NTSB have primary jurisdiction.
Proposed § 450.173(d) would establish mishap reporting requirements applicable to all operations, vehicles, or mishap types. Proposed § 450.173(d)(1) would require that an operator immediately notify the FAA WOC in case of a mishap involving a fatality or serious injury. Immediately would continue to mean notification without delay. The immediate notification should not hamper emergency response activities. Proposed § 450.173(d)(2) would require that operators report other mishaps not involving a fatality or serious injury to the WOC within 24 hours. This would eliminate the current option to notify the Associate Administrator for Commercial Space Transportation instead of the WOC because the WOC, unlike the Administrator for Commercial Space Transportation, is available 24-hours per day, 7 days per week. Proposed § 450.173(d)(3) would require operators to submit a written preliminary report to the FAA Office of Commercial Space Transportation within five days of any mishap. The report would need to include the information listed in proposed § 450.173(d)(3).
This list of information would include the operator's assessment on how the cause of its mishap could potentially affect similar vehicles, systems, or operations. Given some systems and components are common across operators, this information could prevent mishaps due to similar failures of a common system or component, including ground and range systems. The reporting requirements in this paragraph are similar to existing five-day reporting requirements. Under current regulations, a five-day preliminary written report was only required in the event of an accident or incident. Based on lessons learned from past mishaps, the FAA is streamlining these reporting requirements to ensure consistency between mishap classes and that information required to properly classify a mishap and the level of investigation required are reported. For example, mishaps involving a fatality or serious injury are typically investigated at the Federal level, as such, the FAA is aware of the information that may affect the safety of the public or public property.
The operator, in accordance with their mishap plan, may investigate mishaps not involving a fatality or serious injury. In such cases, it is possible that the FAA may not become aware of information potentially affecting the public safety or public property in a timely manner, or other facts that may require elevating the class of mishap to a higher level.
Proposed § 450.173(e) sets emergency response requirements. Proposed § 450.173(e)(1) would require that an operator activate emergency response services following a mishap. This requirement is consistent with the post-launch and post-flight attempt hazard controls in current § 417.415. Proposed § 450.173(e)(2) would require that an operator maintain existing hazard area surveillance and clearance as necessary to protect public safety. These notices would include NOTAM and NOTMAR. Proposed § 450.173(e)(3) would require that an operator contain and minimize the consequences of a mishap. Proposed § 450.173(e)(4) would provide for the preservation of data and physical evidence, including debris, which the FAA considers to be a physical record. In an effort to contain and minimize the consequences of the mishap and maintain site integrity for investigation, an operator would need to safe and secure the mishap site in a timely manner. Proposed § 450.173(e)(4) is consistent with current requirements.
Proposed § 450.173(e)(5) would require an operator to implement agreements with local government authorities and emergency response services, as necessary. Emergency response procedures should identify who is responsible for securing the mishap site, and procedures for access to the mishap site. For example, the procedures should identify who is responsible for educating persons on the treatment of debris, and the disposal of hazardous materials. The FAA recommends that prior to beginning operations, an operator coordinate with Federal, state, and local authorities and emergency first responders to familiarize them with permitted and licensed operations and hazards associated with an operator's activities, such as launch vehicle hazards. This pre-coordination is important to ensure the safety of emergency personnel responding to the mishap. Vehicle and operational hazards may include vehicle composites, propellants, oxidizers, pressure vessels, unexploded ordnance, oxygen systems, and batteries.
If implemented, proposed § 450.173(f) would require an operator to investigate the root causes of a mishap and report the results to the FAA. Proposed § 450.173(g) would require that an operator identify and implement preventive measures prior to the next flight, unless otherwise approved by the Administrator. The FAA is proposing that preventive measures be implemented prior to the next flight in all cases in order to codify current practice. The FAA would work with operators on a case-by-case basis to determine whether its next operation may proceed if it is unable to implement preventive measures before the next flight. The requirement to implement corrective action prior to next flight is consistent with existing requirements in § 437.73(d) for anomaly recording, reporting, and implementation of corrective actions.
Proposed § 450.173(h) would require that an operator maintain records associated with a mishap in accordance with proposed § 450.219(d) (Records). The operator would make these records available to Federal officials for inspection and copying. This requirement is consistent with existing record keeping requirements.\148\ Records would include debris, which the FAA considers a physical record. In all mishap cases, disposal of any related debris would be required to be coordinated with the FAA. Note that this proposal would allow for the sharing of proposed § 450.173 responsibilities between launch and reentry operators pursuant to an agreement. For example, the site operator may report the mishap occurrence to the FAA as required by proposed § 450.173(d), while the emergency response requirements of proposed § 450.173(e) may be shared by both the launch or reentry operator and site operator. An operator would be required to retain all records until completion of any Federal investigation and the FAA advises the operator that the records need no longer be retained.
\148\ Sections 417.15(b), 420.61(b), 431.77(b), and 437.87(b).
Finally, proposed § 450.173(i) would set application requirements. This section would require the submission of the mishap plan document at the time of license or permit application. v. Test-Induced Damage
The FAA proposes to introduce a test-induced damage exception to the mishap definition in proposed § 450.175 (Test-induced Damage). This proposal would allow an operator to coordinate testing activities with the FAA before the activities take place to prevent the FAA from labeling failures as mishaps. Any test failure covered by this section would be considered test-induced damage and not a mishap, so long as the failure falls within the pre-coordinated and FAA-approved testing profile. The test-induced damage concept is not currently within the FAA's commercial space regulations. This proposal is due to the FAA's recognition that current mishap regulations may deter the kind of robust testing that may yield future safety benefits.
The FAA currently deems a failure to achieve test objectives as a mishap (failure to complete a launch or reentry as planned). Similarly, a test failure that results in over $25,000 in damage to associated property would also be considered a mishap.\149\ In both cases, the resulting mishap designation would require a mishap investigation to identify root causes and preventive measures, which the operator would need to implement before the next operation.
\149\ "[R]esulting in greater than $25,000 worth of damage . . ." in accordance with the mishap definition in § 401.5.
In the recent past, the FAA accepted the possibility of a test-induced damage approach by pre-coordinating with a launch operator prior to conducting an in-flight abort test of a crew escape system.\150\ The FAA found that this process worked well in pre-defining the objectives of the test, test limits, expected outcomes, and potential failure modes. It also allowed the operator and FAA to reach a common understanding of what events would be categorized as a test-induced damage or mishap. This approach would also be consistent with ARC feedback that the existing mishap definition leads to protracted mishap investigations because it does not recognize the difference between operational missions and higher risk experimental or test missions. The ARC and FAA believe this discourages robust testing to push the limits of a vehicle and undercutting test programs currently covered under experimental permits.
\150\ Given these events fell within the pre-coordinated possible scenarios, the FAA did not consider them unplanned events and therefore, did not consider the events mishaps.
As noted earlier, the ARC shared its concern that current mishap reporting and investigation requirements discourage robust testing. The FAA believes that the proposed test-induced damages paradigm addresses this concern by providing an opportunity for license applicants and existing license holders to pre-coordinate test activities and pre-declare damages that the FAA would not consider a mishap. Under this paradigm, failure to achieve identified test objectives and certain pre-declared damages to property associated with the licensed activity, including ground support equipment, ground support systems, and flight hardware would not be reportable as an FAA-mishap provided the requirements of this section are met. The FAA also proposes to replace its existing mishap related definitions in favor of a mishap classification system to further clarify the types of events that would be considered a mishap.
Proposed § 450.175(a) would lay out the specific conditions for the test-induced damage approach. It would require an operator to coordinate test activities with and obtain approval from the FAA before the planned activity. The coordination should take place with sufficient time for the FAA to evaluate the proposal during the application process or as a license modification. A test activity would need to be pre-coordinated with the FAA to be eligible for the test-induced damage mishap exception. The FAA would conduct pre-coordination activities during pre-application consultation. The test-induced damage exception would be optional and an operator would not be required to take this path. However, absent the test-induced damage exception, the FAA would categorize an unplanned event as a mishap in accordance with the proposed mishap classification system. Proposed § 450.175(a)(2) would preclude certain kinds of mishaps from the test-induced damage alternative.
Specifically, any mishap involving a serious injury or fatality, damage to property not associated with the licensed activity, or hazardous debris leaving the pre-defined hazard area would be treated as a mishap and not test-induced damage. Finally, proposed § 450.175(a)(3) would require test-induced damage to fall within the scope of activities coordinated with the FAA to be eligible for this alternative. In other words, the FAA would consider the occurrence of damages resulting from test activities that fall outside the scope of approved activities (e.g., before scheduled test activities begin or exceeding operation limits) as a mishap in accordance with the proposed mishap classification system. The approved scope of the test would be outlined in the information submitted by the permittee or licensee to meet the application requirements of proposed § 450.175(b).
Proposed § 450.175(b) would set the test-induced damage application requirements. The paragraph would list the information an applicant would need to submit under the test-induced damage alternative to mishap classification. The FAA does not intend the test-induced damage exception to apply to the operation of an entire vehicle, but rather the testing of specific components and systems. The applicant should submit test objectives in a complete, clear, and concise manner to help the FAA distinguish between nominal operations and specific test objectives. It should also provide test limits such as the expected environments, personnel, equipment, or environmental limits. Also, the applicant would identify expected outcomes that the FAA would later compare to actual outcomes. The FAA would also request a list of potential risks, including the applicant's best understanding of the uncertainties in environments, test limits, or system performance. Applicable procedures or steps taken to execute the tests and the expected time and duration of the test would also be required. Finally, the FAA may request additional information such as clarification information to ensure public safety, safety of property, and to safeguard the national security and foreign policy interests of the United States.
This proposal is similar to NASA's test-induced damages process, as defined in NPR 8621.1C (NASA Procedural Requirements for Mishap and Close Call Reporting, Investigating, and Recordkeeping). NASA developed the test-induced damages paradigm in support of the December 2014 launch of Exploration Flight Test-1 and it has been in use supporting NASA test programs ever since. The test-induced damages process is a formal process documenting the risk of damage and accepting that risk by signature before the test. Similar to the commercial space industry, NASA conducts tests to better understand and mitigate complex design, manufacturing, or operational issues with the objective of providing NASA with confidence that the system meets its technical and programmatic requirements and can successfully and safely perform its mission in the operational environment. As noted in NPR 8261.1C, some tests are designed and intended to result in hardware damage (e.g., a structural test-to-failure). Other tests are aggressive in nature, and test-incurred damage often occurs; the knowledge gained is used to improve designs. These statements hold true for the commercial space transportation industry as well. The FAA's proposed test-induced damages takes a NASA-proven process and tailors it to satisfy the FAA's public safety mission.
L. Pre- and Post-Flight Reporting
L. Pre- and Post-Flight Reporting
1. Preflight Reporting
Under proposed § 450.213, the FAA would continue to require a licensee to provide the FAA with specified information prior to each launch or reentry, consistent with current requirements. An operator would send the information as an email attachment to [email protected], or by some other method as agreed to by the Administrator in the license. The FAA would require five categories of information: mission-specific, flight safety analysis products, flight safety system test data, data required by the FAA to conduct a collision avoidance analysis, and a launch or reentry schedule.
1. Preflight Reporting
The first category would be mission-specific information in proposed § 450.213(b). As currently required in Sec. § 417.17(b)(2) and 431.79(a), an operator would be required to provide this information to the FAA not less than 60 days before each mission conducted under the license. The FAA may also agree to a different time frame in accordance with § 404.15. An operator would not have to provide any information under this section if the mission-specific information was already provided in the application. This would be the case if an operator's license authorizes specific missions, as opposed to unlimited launches or reentries within certain parameters.
Specifically, an operator would continue to have to provide payload information in accordance with proposed § 450.43(i), and flight information, including the vehicle, launch site, planned flight path, staging and impact locations, each payload delivery point, intended reentry or landing sites including any contingency abort locations, and the location of any disposed launch or reentry vehicle stage or component that is deorbited. This section would combine the reporting requirements of Sec. § 417.17(b)(2) and 431.79(a), although reporting the location of any disposed launch or reentry vehicle stage or component that is deorbited would be a new requirement. The FAA would add this information requirement because disposals are much more common now than when parts 417 and 435 were issued, and notifications to airmen and mariners would be necessary to protect the public from vehicle stages or components reentering as part of a disposal. In practice, licensees have arranged for the issuance of NOTAMs and NTMs for vehicle stages purposefully deorbited.
The second category is flight safety analysis products in proposed § 450.213(c). An operator would need to submit to the FAA updated flight safety analysis products, using previously-approved methodologies, for each mission no less than 30 days before flight. The FAA may also agree to a different time frame in accordance with proposed § 404.15. The flight safety analysis products are similar to what is currently required under § 417.17(c)(3). Part 431 does not require similar flight safety analysis products to be submitted, although current practice is to require similar information in license orders.
An operator would not be required to submit flight safety analysis products if the analysis submitted in the license application already satisfies all the requirements of the section. This would be the case if a licensee's license authorizes specific missions, as opposed to unlimited launches within certain parameters. An operator would also not be required to submit flight safety analysis products if the operator demonstrated during the application process that the analysis does not need to be updated to account for mission-specific factors. This would be the case if an operator operates within certain operational constraints proven to satisfy public safety criteria.
Otherwise, an operator would be required to submit flight safety analysis products while accounting for vehicle and mission specific input data and potential variations in input data that may affect any analysis product within the final 30 days before flight. An operator would also be required to submit the analysis products using the same format and organization used in its license application. Lastly, an operator would not be able to change an analysis product within the final 30 days before flight, unless the operator has a process, approved in the license, for making a change in that period as part of the operator's flight safety analysis process.
The third category is flight safety system test data in proposed § 450.213(d). If an operator would be required to use an FSS to protect public safety as required by proposed § 450.101(c), it would need to submit to the FAA, or provide access to, any test reports in accordance with approved flight safety system test plans no less than 30 days before flight. The FAA may also agree to a different time frame in accordance with proposed § 404.15. This reporting requirement is discussed earlier in the section for flight safety systems.
The fourth category would be data required by the FAA to conduct a collision avoidance analysis in proposed § 450.213(e). Not less than 15 days before the flight of a launch vehicle or the reentry of a reentry vehicle, an operator would need to submit the collision avoidance information in proposed Appendix A to part 450 to a Federal entity identified by the FAA, and the FAA. This reporting requirement is discussed in the "Launch and Reentry Collision Avoidance Requirements" section.
The fifth category, as proposed in § 450.213(f), a launch or reentry schedule that identifies each review, rehearsal, and safety-critical operation. The schedule would be required to be filed and updated in time to allow FAA personnel to participate in the reviews, rehearsals, and safety-critical operations. This is similar to current § 417.17(b).
2. Post-Flight Reporting
Under proposed § 450.215, the FAA would require an operator to provide specified information no later than 90 days after a launch or reentry. The FAA may also agree to a different time frame in accordance with proposed § 404.15. An operator would send the information as an email attachment to [email protected], or other method as agreed to by the Administrator in the license.
Specifically, as discussed earlier, an operator would need to provide any anomaly that occurred during countdown or flight that is material to public health and safety and the safety of property,\151\ and any corrective action implemented or to be implemented after the flight due to an anomaly or mishap. Section 417.25(b) and (c) requires similar information. Part 431 does not require post-flight information, although current practice is to require similar information in license orders.
\151\ What is material to public health and safety and the safety of property is discussed later in this preamble in reference to proposed § 450.211(a)(2).
In addition, an operator would need to provide the actual trajectory flown by the vehicle, and, for an unguided suborbital launch vehicle, the actual impact location of all impacting stages and impacting components. The actual trajectory flown by the vehicle would be a new requirement, while the actual impact locations for an unguided suborbital launch vehicle is similar to the requirements in current § 417.25(b) and (c). The FAA would use the actual trajectory flown by the vehicle to compare it to predicted trajectories. Because the FAA may not need this information for all launches, this information would only need to be reported if requested by the FAA.
Lastly, an operator would need to report the number of humans on board the vehicle. This would be required because the FAA keeps a human space flight database for use by launch and reentry operators for the purposes of informed consent. Under § 460.45(c), and pursuant to statute, an operator must inform each space flight participant of the safety record of all launch or reentry vehicles that have carried one or more persons on board, including both U.S. government and private sector vehicles, to include the total number of people who have died or been seriously injured on these flights, the total number of launches and reentries conducted with people on board, and the number of catastrophic failures. To facilitate all operators accurately informing space flight participants, the FAA maintains the human space flight database and populates it using voluntarily provided information from industry. As more launches and reentries are expected with humans on board, the FAA will require this information to keep the human spaceflight database up to date, and expects that this would not significantly increase the burden to operators.
Ground Safety
Ground Safety
A. Definition and Scope of Launch
As discussed in more detail in this section, the FAA proposes to amend the definitions of "launch" and "reentry" in part 401 to mirror the statutory definitions. The FAA would move the beginning and end of launch to proposed § 450.3, which defines the scope of a vehicle operator's license. Proposed § 450.3(b) would establish that launch begins under a license with the start of hazardous activities that pose a threat to the public, and it would amend the end of launch language to remove any reference to ELVs and RLVs. Finally, the FAA proposes to clarify that, absent the launch vehicle, the arrival of a payload at the launch site would not trigger the beginning of launch. Also, at a non-U.S. launch site, launch would begin at ignition or take-off for a hybrid vehicle.
A. Definition and Scope of Launch
Title 51 U.S.C. 50902 defines launch as to place or try to place a launch vehicle or reentry vehicle and any payload or human being from Earth in a suborbital trajectory; in Earth orbit in outer space; or otherwise in outer space, including activities involved in the preparation of a launch vehicle or payload for launch, when those activities take place at a launch site in the United States. The FAA added the current regulatory definition of launch in the 1999 final rule.\152\ The language in the regulatory definition differs slightly from the current statutory language regarding activities in preparation of the vehicle, and the regulatory definition does not include the reference to human beings because that reference was added to the statute after 1999.\153\ The regulatory definition also includes language that is not set forth in the statute pertaining to pre- and post-flight ground operations including language identifying the beginning of launch and end of launch.
\152\ 64 FR 19586 (April 21, 1999).
\153\ As currently defined in 14 CFR 401.5, launch means to place or try to place a launch vehicle or reentry vehicle and any payload from Earth in a suborbital trajectory, in Earth orbit in outer space, or otherwise in outer space, and includes preparing a launch vehicle for flight at a launch site in the United States. The current definition also defines beginning and end of launch, which, as discussed later in the preamble, the FAA proposes to amend and move to proposed part 450 (Scope of a vehicle operator license).
The FAA and industry have identified a number of issues associated with the current definition of launch in § 401.5. The current definition of launch is inflexible and has resulted in confusion regarding launch from non-U.S. sites and whether the arrival of a payload constitutes the beginning of launch.
The preamble discussion in the 1999 final rule stated that the intent of the FAA's definition of "launch" is to require a license at the start of those hazardous preflight activities that put public safety at risk. The final rule stated that, in accordance with this responsibility, the FAA will exercise regulatory oversight only if an activity is so hazardous as to pose a threat to third parties.
Specifically, the FAA determined that launch begins when hazardous activities related to the assembly and ultimate flight of the launch vehicle commence.\154\ The preamble further elaborated that the moment at which hazardous activities begin is when the major components of a licensee's launch vehicle enter, for purposes of preparing for flight, the gate of a U.S. launch site, regardless of whether the site is situated on a Federal launch range and regardless of whether flight occurs from that site.\155\ At the time, the FAA determined that the arrival of the launch vehicle at a U.S. launch site would trigger the beginning of launch for the following reasons: ease of administration, consistent and broad interpretation, and change in the level of risk.\156\ Additionally, the rule stated that shortly after vehicle components arrive, hazardous activities related to the assembly and ultimate flight of the launch vehicle begin and therefore the arrival of the vehicle or its parts is a logical point at which the FAA should ensure that a launch operator is exercising safe practices and is
financially responsible for any damage it may cause.\157\ In accordance with the definition of launch, the FAA has required a launch license to be in place before the arrival of major components of a launch vehicle at a U.S. launch site that are intended for use on a specific FAA-licensed launch.
\154\ 64 FR 19586 (April 21, 1999), at 19591.
\155\ 64 FR 19586 (April 21, 1999).
\156\ 64 FR 19586 (April 21, 1999), at 19589.
\157\ 64 FR 19586 (April 21, 1999), at 19591.
The lack of flexibility in the definition of beginning of launch has led to multiple requests from the industry to waive the requirement for a license to bring vehicle hardware on site and begin preflight activity.\158\ The FAA has issued numerous waivers because it determined that the proposed preflight activities associated with the arrival of launch vehicles or their major components were not so hazardous to the public as to require FAA oversight. In granting a waiver, the FAA determines that the waiver is in the public interest and will not jeopardize public health and safety, the safety of property, or any national security or foreign policy interest of the United States. In addition, by requesting a waiver to conduct preflight activities, the operator agrees that it must forgo the opportunity to seek indemnification for any loss incurred under the waiver during the waived preflight activities.
\158\ As stated previously, the FAA is only able to waive regulatory requirements, not definitions, and therefore has issued waivers to the requirement to obtain a license, rather than to the definition of launch.
Further, the current definition does not account for the significant technological advances the industry has experienced since adoption of the 1999 rule. For example, in the current commercial space transportation environment, launch operations often include vehicles or vehicle stages that fly back to a U.S. launch site and remain at the launch site. In cases where no license was in place to cover the presence of flight hardware for possible reuse, consistent with 1999 rule preamble language, the FAA has deemed this to be storage and does not require a license or waiver.\159\ As currently written, however, the definition could imply that a license is required for RLV launches during the period between end-of-launch and launch vehicle reuse, even when the vehicle is in a safe and dormant state, and would not be a threat to public safety.
\159\ 64 FR 19586 (April 21, 1999), at 19593. "On the other hand, the FAA does not intend a launch license to encompass components stored at a launch site for a considerable period of time prior to flight."
Because the current definition states that launch begins under a license with the arrival of a launch vehicle or payload at a U.S. launch site, the term "or payload" has been interpreted to mean arrival of a payload by itself could constitute beginning of launch. However, the 1999 preamble explicitly states that the FAA does not define launch to commence with the arrival of a payload absent the launch vehicle at a launch site.\160\ Also, it states that the FAA does not consider payload processing absent launch vehicle integration to constitute part of licensed activities.\161\ In addition, the 1999 rule preamble refers to launch beginning when the "major components" of a launch vehicle arrive at the launch site. However, the regulatory language remains unclear.
\160\ 64 FR 19586 (April 21, 1999), at 19589.
\161\ 64 FR 19586 (April 21, 1999), at 19593.
Another point of current uncertainty is when launch begins from a non-U.S. site. Title 51 U.S.C. chapter 509 gives the FAA authority to issue a launch license to a U.S. citizen conducting a launch anywhere in the world. However, the current definition of launch is silent as to when launch begins from a non-U.S. site. This has resulted in operators lacking clarity as to when launch begins. In recent years, the FAA has licensed launches from international waters, Australia, the Marshall Islands, New Zealand, and Spain. In licensing these launches, the FAA has consistently interpreted that launch from outside of U.S. territory to begin at ignition or at the first movement that initiates flight, whichever occurs earlier.
The ARC commented about the definition of launch for licensed launches from a U.S. launch site. The ARC report stated that launch should be defined on a case-by-case basis for all operators. The ARC recommended licensed activities on U.S. launch sites for all vehicles include preflight ground operations, flight operations, and launch operations phases as tailored by each launch operator. The ARC further recommends the initiation and scope of launch activities, including preflight ground operations and flight operation phases, be defined by the impact of each activity on public safety and property. These activities may include both hazardous and safety-critical operations, the latter encompassing non-hazardous activities that may impact public risk during other pre-launch and flight activities. A list of performance-based criteria for licensed activities would be tailored for each operator and the FAA based on their specific concept of operations. This scope should only include hazardous operations unique to activities as defined in the operator's license application documents and not activities already regulated by another government agency.
In light of the multiple waiver requests and ARC recommendations, the FAA proposes to amend the regulatory definitions of launch and reentry (discussed later in this section) to match the statutory definitions. The FAA would also move the details in the definitions for beginning and end of launch (discussed later in this section) and reentry to the scope of a vehicle operator license requirements in proposed § 450.3. In addition, the FAA would revise "beginning of launch" to be more performance-based and "end of launch" to remove references to ELVs and RLVs. Finally, the FAA proposes to clarify that launch from a non-U.S. site would begin at ignition, and that the arrival of a payload to a launch site does not constitute beginning of launch. The FAA believes the proposed revisions capture the primary intent of the ARC's recommendation, which is to limit FAA oversight to those launch operations that pose a hazard to public safety and the safety of property.
The FAA would revise the definitions of launch and reentry in § 401.5 to mirror the statutory definitions. Specifically, the FAA would remove the beginning and end of launch language from the definition of "launch," and add the term "human being" to align with the 2015 update to the Act. Similarly, the FAA would revise the definition of "reenter/reentry" in part 401 to mirror the statutory definition, and would add the term "human being" to align with the 2015 update to the Act.
The FAA would move the beginning and end of launch and reentry language to proposed § 450.3. The FAA proposes this change because such detail in a definition makes the definition unwieldy and, unlike regulatory requirements, definitions cannot be waived.
The FAA would amend beginning of launch such that launch begins with the first hazardous activities related to the assembly and ultimate flight of the launch vehicle at a U.S. launch site. Unless a later point is agreed to by the Administrator, hazardous preflight ground operations would be presumed to begin when the launch vehicle or its major components arrive at the launch site. For operations where an applicant identifies a later time when hazardous operations begin, the applicant may propose the event that it believes should constitute the beginning of launch during the pre-application process.\162\ As a result, there would be no need to request a waiver.
\162\ The FAA's proposal regarding how an operator would determine what event constitutes the beginning of launch, and how to obtain the Administrator's approval, is located in the Ground Safety section under the Identifying First Hazardous Activity sub-heading of this preamble.
This proposed change would also clarify that for launch vehicle stages or when launch begins for an RLV that returns to a launch site and remains there in a dormant state, FAA oversight is not necessary since no hazardous activity that falls under the FAA's oversight responsibilities are being performed.
This proposal would clarify that, absent vehicle hardware, the arrival of payload does not constitute beginning of launch. Instead, launch would begin with the arrival of a launch vehicle or its major components at a U.S. launch site, or at a later point as agreed to by the Administrator.
This proposal would also specify that launch from a non-U.S. site begins at ignition, or at the first movement that initiates flight, of the launch vehicle, whichever comes first. For hybrid vehicles, flight commences at take-off. The current "beginning of launch," as defined in the definition of "launch" refers only to launches from a U.S. launch site, and is silent with regard to launches from sites outside the United States. Although the FAA issues launch licenses for launches from non-U.S. launch sites if the operator is a citizen of the U.S., the FAA considers it outside its authority to license preflight activities that take place at a non-U.S. launch site in light of the statutory definition of launch that explicitly refers to "activities involved in the preparation of a launch vehicle . . . when those activities take place at a launch site in the United States." The FAA also believes that this interpretation is necessary because of issues of sovereignty and liability under international law. For these non-U.S. launch sites, the FAA has historically licensed launches beginning at ignition, or if there is no ignition, then at the first movement that initiates flight. In order to provide clarity for launch operators launching from non-U.S. sites, the FAA is proposing to codify this approach in part 450.
In addition to addressing issues in the current definition of "launch" regarding when launch begins, the FAA proposes to clarify when launch ends. First, the FAA would move the provisions in the current definition of launch regarding end of launch to proposed § 450.3. Second, the FAA would remove the distinction between ELVs and RLVs, which is consistent with one of the overall goals of this proposed rule. Overall, the substance of the current provisions related to end of launch currently located in § 401.5 would not change. Specifically, launch ends:
1. For an orbital launch of an ELV, after the licensee's last exercise of control over its vehicle whether on orbit or a vehicle stage impacting on Earth;
2. For an orbital launch of an RLV, after deployment of all payloads or if there is no payload, after the launch vehicle's first steady state orbit; and
3. For a suborbital launch of either an ELV or RLV that includes reentry, launch ends after reaching apogee; or for a suborbital launch that does not include a reentry, launch ends after the vehicle or vehicle component lands or impacts on Earth.
In all these cases, activities on the ground to return either the launch site or the vehicle or vehicle component to a safe condition are part of launch and could possibly extend the end of launch. In the rare, yet to be seen, situation of a suborbital launch that does not require an FAA launch license but does require a reentry license, launch ends after the vehicle reaches apogee. In addition, the FAA would move the provisions related to reentry readiness and returning the vehicle to a safe state on the ground to proposed § 450.3. Including these reentry provisions in the scope of a vehicle operator license would clarify an operator's responsibilities regarding post-flight ground operations related to returning the vehicle to a safe state on the ground.
Finally, the FAA proposes to modify the definition for reentry. Title 51 U.S.C. 50902 defines reentry as: to return or attempt to return, purposefully, a reentry vehicle and its payload or human beings, if any, from Earth orbit or from outer space to Earth. In 2000, the FAA codified the current regulatory definition of reentry in the final rule, Commercial Space Transportation Reusable Launch Vehicle and Reentry Licensing Regulations. Section 401.5 defines "reenter; reentry" as: To return or attempt to return, purposefully, a reentry vehicle and its payload, if any, from Earth orbit or from outer space to Earth. The term "reenter; reentry" includes activities conducted in Earth orbit or outer space to determine reentry readiness, and that are critical to ensuring public health and safety and the safety of property during reentry flight. The term "reenter; reentry" also includes activities conducted on the ground after vehicle landing on Earth to ensure the reentry vehicle does not pose a threat to public health and safety or the safety of property. As noted earlier, the FAA proposes to revise the definition to mirror the statute and move the provisions related to reentry readiness and returning the vehicle to a safe state on the ground to proposed § 450.3.
B. Ground Safety Requirements
B. Ground Safety Requirements
This proposal would revise current ground safety requirements to make them more flexible, scalable, and adaptable to varying types of launch and reentry operations. The proposal seeks to ensure that the FAA's oversight of ground operations at U.S. launch sites would only cover activities that are hazardous to the public and critical assets. Specifically, as proposed in § 450.179, an operator would be required to protect the public from adverse effects of hazardous operations and systems associated with preparing a launch vehicle for flight, returning a launch or reentry vehicle to a safe condition after landing, or after an aborted launch attempt, and returning a site to a safe condition. An operator would be required to conduct a ground hazard analysis (proposed § 450.185) and comply with certain prescribed hazard controls during those preflight activities that constitute launch. In addition, an operator would be required to comply with other ground safety and related application requirements in proposed part 450.
The FAA proposed the part 417 ground safety regulations in the 2000 NPRM \163\ and codified it in the 2006 final rule. The 2006 final rule adopted ground safety standards governing the preparation of a launch vehicle for flight. The final rule specified that in order for a launch operator to meet part 417 ground safety requirements, an operator must conduct a ground hazard analysis to meet the requirements of subpart E, part 417, as well as a toxic release hazard analysis to meet the requirements of § 417.227. For launches conducted from a Federal launch range, a launch operator could rely on an LSSA as an alternative means of demonstrating compliance with the FAA's part 417 ground safety rules. Because most licensed ground operations were covered by the LSSA approach, the FAA did not begin to exercise the ground safety requirements in part 417 until 2016.
\163\ Licensing and Safety requirements for Launch, NPRM. 65 FR 63922 (October 25, 2000).
Beginning in 2016, the FAA received several applications for launch licenses from non-Federal launch sites.\164\ Applicants were required to demonstrate compliance with the ground safety regulations in part 417. During the FAA's evaluation, the agency found that many of its ground safety requirements were overly burdensome, highly prescriptive, and did not include criteria for determining public safety. Furthermore, the FAA discovered the requirements were out-of-date with commercial space transportation practices and operations, and in some cases duplicated other state and Federal regulations.
\164\ The FAA's first license application involving a launch from a non-Federal launch range was from SpaceX for operations at pad 39A in Cape Canaveral, Florida. The FAA completed its evaluation and issued SpaceX the license on February 2017. Astra Space originally applied for a launch license from a non-Federal launch range in June 2017, and the FAA issued its license March 2018.
Part 431 does not include explicit ground safety requirements. However, the scope of a launch license under part 431 includes preparing a launch vehicle for flight at a launch site in the United States. In conducting its safety review under § 431.31, the FAA must determine whether an applicant is capable of launching an RLV and payload, if any, from a designated launch site without jeopardizing public health and safety and the safety of property. The FAA evaluates on an individual basis all public safety aspects of a proposed RLV mission to ensure they are sufficient to support safe conduct of the mission, including ground safety. In licenses issued under part 431, the FAA has required operators to address reasonably foreseeable hazards to ensure the safety of pre- and post-flight ground operations. The lack of clarity in part 431 is problematic, and would be fixed by the ground safety requirements in this proposal.
The ARC recommended that the FAA create ground safety regulations that are flexible and streamlined, continue to protect the public, and are not duplicative of other state or Federal authorities. The ARC provided four primary recommendations for ground safety. First, the ARC recommended the FAA allow operators to determine what activities and operations would be covered under FAA regulations by performing an analysis to define hazards. Second, the ARC recommended the FAA scale the scope of what is considered licensed activities based on each operator's unique operations. Third, the ARC recommended the FAA focus its regulatory authority solely on those things that affect public safety. Finally, the ARC recommended the FAA only regulate those things that are not already overseen by other governmental authorities.
The FAA agrees with the ARC's recommendations that ground safety regulations should be flexible, performance-based, and utilize a ground hazard analysis that determines the best methods for protecting the public. The proposed ground safety regulations would rely on a system safety approach to allow flexibility by stripping away specific design requirements, establishing more performance-based requirements, and giving the operator flexibility in satisfying these requirements. Specifically, an operator would conduct a ground hazard analysis (proposed § 450.185), and comply with prescribed hazard controls. In addition to any mitigations identified in the ground hazard analysis, the proposed regulations would require several prescribed hazard controls, including an accounting of how the operator would protect members of the public who enter areas under their control, provisions on how the operator would mitigate hazards created by a countdown abort, an explanation of the operator's plans for controlling fires, and generic emergency procedures an operator would implement. As will be discussed later, operators using toxic materials would have to perform a toxic release hazard analysis (proposed § 450.187), show how it would contain the effects of a toxic release, or how the public would be protected from those risks from toxic releases. Operators would also be required to develop an explosive siting plan (proposed § 450.183) and to coordinate with licensed launch and reentry site operators (proposed § 450.181). 1. Ground Safety: Identifying First Hazardous Activity
In proposed § 450.3, an operator would have the flexibility to determine for its particular operation when the first preflight activity that poses a hazard to the public begins in coordination with the FAA. An operator could identify the arrival of the vehicle or its major components at the launch site as the beginning of hazardous operations, which is consistent with current practice. This option would provide a clear demarcation of when launch begins that is easily understood by both an operator and the FAA. The license would cover all ground operations that may present a hazard to the public from the time flight hardware first arrives at the launch or reentry site to the end of launch or reentry.
Alternatively, an operator could identify some other action, after the arrival of the vehicle or its major components at the launch site, as the beginning of hazardous activities. As discussed earlier in the scope of a vehicle operator license discussion, this option would be available for those operations where the arrival of the launch vehicle does not constitute the beginning of hazardous activities. It would also provide flexibility to operators because the start of hazardous launch operations is unique to each operator's circumstances. These hazardous launch operations would include the pressurizing or loading of propellants into the vehicle or launch system,\165\ operations involving a fueled launch vehicle,\166\ or the transfer of energy necessary to initiate flight.\167\
\165\ This would include the loading of propellants or pressurants, where there are potential hazards such as overpressure, explosion, debris, deflagration, fire, and toxic material release. The operations that are typically performed include wet dress rehearsals, cold flow, returning the vehicle to a safe state following a scrub, and tests that might be performed while the vehicle is being fueled.
\166\ This would include static fire or tests with a fully-fueled integrated vehicle.
\167\ This would include activities that involve placing the launch vehicle into a state that would enable it to achieve suborbital or orbital flight. Even if traditional propellants are not used, the energy needed to escape Earth's gravity is significant and the initiation of the action to launch a vehicle could potentially have significant impact to public safety.
While this option offers greater flexibility, it would require that an applicant talk with the FAA during pre-application consultation to identify which activity would be the beginning of hazardous launch operations. This is necessary for the FAA to scope its requirements accordingly, and so that the applicant knows what to include in its application. Early interactions with the FAA would allow a potential applicant to work with the FAA to determine which preflight operations constitute launch and therefore must occur under a license. An applicant that elects to identify an activity after the arrival of a launch vehicle or associated major components at a launch site as the beginning of launch should be prepared to discuss its operations with the FAA so that the FAA can determine that operations occurring prior to that point would not pose a threat to public safety. Note that under this proposal, indemnification and reciprocal waiver of claims coverage would start when launch begins as it does under current regulations. In other words, financial responsibility requirements would apply from the first hazardous operation until launch ends. 2. Ground Safety: Ground Hazard Analysis
Proposed § 450.185 (Ground Hazard Analysis) would require an operator to complete a ground hazard analysis which would include a thorough assessment of the launch vehicle, the launch vehicle integrated systems, ground support equipment, and other launch site hardware. The analysis would include an identification of hazards, a risk assessment, an identification and description of mitigations and controls, and provisions for hazard control verification and validation. Although the analysis might incorporate employee safety and mission assurance, this proposal would only require an applicant to identify the hazards that affect the public, and how an operator would mitigate those hazards.
Proposed § 450.185(a) would require an operator to identify hazards. A hazard is a real or potential condition that could lead to an unplanned event or series of events resulting in death, serious injury, or damage to or loss of equipment or property. The FAA proposes separating ground hazards into two primary categories: System and operational hazards. System hazards would include, but would not be limited to, vehicle over-pressurization, sudden energy release including ordnance actuation, ionizing and non-ionizing radiation, fire or deflagration, radioactive materials, toxic release, cryogens, electrical discharge, and structural failure. Operational hazards would be hazards introduced to the launch site through procedures and processes that occur during vehicle processing. Operational hazards would include propellant handling and loading, transporting vehicles or components, vehicle system activation, and related tests.
Once an operator has identified hazards, proposed § 450.185(b) would require an operator to conduct a risk assessment. In other words, an operator would have to evaluate each hazard to determine the likelihood and the severity of that hazard. This assessment should identify the likelihood of each hazard causing a casualty. This assessment should also account for the likelihood of each hazard causing major damage to public property or critical assets. Public property, in this case, means any property not associated with the operation. Critical assets means an asset that is essential to the national interests of the United States, and includes property, facilities, or infrastructure necessary to maintain national defense, or assured access to space for national priority missions.
Proposed § 450.185(c) would require an operator to identify mitigations or controls used to eliminate or mitigate the severity or likelihood of identified hazards. An operator would be required to demonstrate, as part of its ground hazard analysis, that the mitigations or controls reduce the likelihood of each hazard that may cause (1) death or serious injury to the public to an extremely remote likelihood, and (2) major damage to public property or critical assets to a remote likelihood. These qualitative thresholds are the same as those in § 437.55(a)(3) and proposed § 450.109(a)(3). A hazard control is a preventative or mitigation measure that reduces the likelihood of the hazard or ameliorates its severity.
Proposed § 450.185(d) would require an operator to identify and describe the risk elimination and mitigation measures required to satisfy the risk criteria in proposed § 450.185(c). Under current industry standards, these measures include one or more of the following: Design for minimum risk, incorporate safety devices, provide warning devices, or implement procedures and training, as previously discussed in reference to the analogous flight hazard analysis requirement in § 450.109(a)(4).\168\
\168\ MIL-STD-882E, section 4.3.4.
Finally, proposed § 450.185(e) would require an operator to demonstrate through verification and validation that the risk elimination measures meet the remote and extremely remote standards discussed earlier. Verification is an evaluation to determine that safety measures derived from the ground hazard analysis are effective and have been properly implemented. Verification provides measurable evidence that a safety measure reduces risk to acceptable levels. Validation is an evaluation to determine that each safety measure derived from the ground hazard analysis is correct, complete, consistent, unambiguous, verifiable, and technically feasible. Validation ensures that the right safety measure is implemented, and that the safety measure is well understood.
While this proposal would require an operator to complete a full ground hazard analysis as described previously, an operator would not need to submit this analysis in its entirety as part of its vehicle operator license application. Rather in proposed § 450.185(f), the FAA would require an applicant to provide a description of the ground safety hazard analysis methodology, a list of the systems and operations involving the vehicle or payload that may cause a hazard to the public, and the results of the ground hazard analysis that affect the public. Although the results of the ground hazard analysis would be unique to each applicant's operations, the ground hazard analysis application deliverables should have common elements. Specifically, the ground hazard analysis should contain the hazards that have a high likelihood or high severity of affecting the public. The analysis should include controls for the hazards that mitigate the risk to the public and all of the other requirements shown in § 450.185.
Common hazards that affect public safety, which the FAA would expect to be addressed in a ground hazard analysis, include propellant loading, ordinance installation or actuation, proximity to pressurized systems during operations, certain lifting operations (such as solid rocket motors and payload integration), operations which could result in toxic release, and RF testing. Fundamentally, if the operator identifies a hazard that affects the public, it must be properly documented and mitigated to reduce the risk to the public. It should be noted that any part of the ground hazard analysis could be reviewed during inspection. 3. Ground Safety: Ground Safety Prescribed Hazard Controls
In addition to those mitigations an operator would implement as a result of its ground hazard analysis, proposed § 450.189 (Ground Safety Prescribed Hazard Controls) would require an operator to implement certain prescribed hazard controls during the ground operations period of launch or reentry. These prescribed hazard controls would require that an operator document how it would protect members of the public who enter areas under the operator's control, mitigate hazards created by a countdown abort. They would also require the operator's plans for controlling fires and emergency procedures.
Specifically, proposed § 450.189(b) would require an operator to document a process for protecting members of the public who enter any area under the operator's control. Although the public would be protected from many hazards because they are excluded from safety clear zones and prevented from entering the site during certain hazardous operations, an operator should account for the protection of the public when they are allowed to be on the site. The proposed rule would require an operator to develop procedures to identify and track members of the public while on site, and methods to protect the public from hazards in accordance with the ground hazard analysis and the toxic hazard analysis. For example, the operator could have plans in place to control who enters its site, whether or not members of the public on site will be escorted, how the public will be made aware of and protected from hazards, and if members of the public will be required to wear personal protective equipment.
This rule would also require an operator to establish, maintain, and perform procedures for controlling certain hazards in the event of a countdown abort or recycle operation. Current § 417.415(b) requires an operator to meet specific requirements for safing their vehicle, maintaining control of their FSS, and controlling access to the site until it is returned to a safe state. This rule would require a more performance-based approach to ensuring the safety of the vehicle and the site following a countdown abort or recycle operation in order to accommodate many different types of flight safety systems and operations.
Proposed § 450.189(c) would require that an operator, following a countdown abort or recycle operation, establish, maintain, and perform procedures for controlling hazards related to the vehicle and returning the vehicle, stages, or other flight hardware and site facilities to a safe condition. In all of these instances, this proposal would require an operator to have provisions in place to keep the public safe while returning the launch vehicle or launch site back to a safe condition. If a launch vehicle does not lift-off after a command to initiate flight, an operator would be required to ensure that the vehicle and any payload are in a safe configuration, prohibit the public from entering into any identified hazard areas until the site is returned to a safe condition, and maintain and verify that any FSS remains operation until certain that the launch vehicle does not represent a risk of inadvertent flight. These more specific requirements would be levied on an operator in the event of a failure to lift-off after a command to initiate because a launch vehicle can be in a particularly hazardous state.
This proposed requirement is similar to § 417.415(b), which requires a launch operator to establish procedures for controlling hazards associated with a failed flight attempt where an engine start command was sent, but the launch vehicle did not lift-off. These procedures must include maintaining and verifying that each flight termination system remains operational, assuring that the vehicle is in a safe configuration, and prohibiting launch complex entry until the launch pad area safing procedures are complete.
Proposed § 450.189(d) would require an operator to have in place reasonable precautions for reporting and controlling any fire that occurs during launch and reentry activities in order to prevent the occurrence of secondary hazards such as a brush fire caused by a static fire test or some related ground launch activity. These secondary hazards, if not controlled, could reach pressure vessels or other related equipment causing more damage. An operator may choose to meet industry standards or fire codes as a means of satisfying this requirement.
Proposed § 450.189(e) would require an operator to establish general emergency procedures that address how emergencies would be handled at the site. An emergency has the potential to directly affect the public or create secondary hazards that may affect the public; therefore, implementation of these procedures are critical for safety of the public. An emergency would include any event that would require an evacuation, or a response from emergency officials such as the fire department or emergency medical technicians. Additionally, the establishment of general emergency procedures would allow the operator to have roles, responsibilities, and plans in place in advance of an emergency to reduce the effects of any emergency on the public. Section 417.111(c)(15) currently requires an operator to have generic emergency procedures in place for any emergency that may create a hazard to the public, and this rule would replace those prescriptive requirements with performance-based requirements.
Proposed § 450.189(f) would require an applicant to submit its process for protecting members of the public who enter any area under the operator's control. This process would be submitted as part of an applicant's vehicle operator license application. 4. Ground Safety: Coordination With a Licensed Launch or Reentry Site Operator
Under proposed § 450.181(a), for a launch or reentry conducted from or to a Federal launch or reentry site or a site licensed under part 420 or 433, an operator must coordinate with the site operator because the two entities each have public safety responsibilities during ground operations. Specifically, an operator must coordinate with the site operator to ensure public access is controlled where and when necessary to protect public safety, to ensure launch or reentry operations are coordinated with other launch and reentry operators and other affected parties to prevent unsafe interference, to ensure that any ground hazard area does not unnecessarily interfere \169\ with continued operation of the launch or reentry site, and to ensure prompt and effective response in the event of a mishap that could impact public safety. This is similar to § 417.9(b)(2), which requires a launch operator to coordinate with a launch site operator and provide any information on its activities and potential hazards necessary for the launch site operator to determine how to protect any other launch operator, person, or property at the launch site. Part 431 requires an agreement between a launch or reentry operator and any site operator in § 431.75. In addition, in the mission readiness review requirements in § 431.37(a), an operator must involve launch site and reentry site personnel and verify their readiness to provide safety-related launch property and launch services.
\169\ The FAA has proposed minimum requirements for ground hazard areas based on safety thresholds, either toxic hazard areas or other hazard areas derived from the ground hazard analysis, but has always allowed operators to propose to clear areas larger than necessary to ensure greater safety. In consultation with NASA and the Department of Defense, the FAA discovered that FAA approved ground hazard areas were having adverse impacts on neighboring space operations in easily avoidable ways. As such, the FAA has proposed ground hazard areas be coordinated with the affected launch or reentry site operators prior to licensing.
For a launch or reentry conducted from or to a site licensed under part 420 or 433, § 450.181(b) would require an operator to also coordinate with the site operator to establish roles and responsibilities for reporting, responding to, and investigating any mishap during ground activities at the site. The same mishap plan requirements in proposed § 450.173 would apply to a site operator leaving open the assignment of roles and responsibilities between a site and launch or reentry operator for reporting, responding to, and investigating mishaps during ground operations. Proposed § 450.181(b) is designed to ensure those roles and responsibilities are established.
As part of its application, an applicant would be required to describe how it is coordinating with a Federal or licensed launch or reentry site operator in compliance with this section. As discussed earlier, in reference to proposed § 450.147, a vehicle operator would be required to submit as part of its vehicle operator license application references to any agreements with other entities utilized to meet any requirements of this section. In this context, agreements may include security, access control services, any lease agreements for launch sites, services used for hazard controls or analysis, or any agreement with local emergency or government services. 5. Ground Safety: Explosive Site Plan
Proposed § 450.183 (Explosive Site Plan) would require an applicant to include an explosive site plan as part of its vehicle operator license application, if it proposes to conduct a launch or reentry from or to a site exclusive to its own use. The explosive site plan would have to demonstrate compliance with the explosive siting requirements of Sec. § 420.63, 420.65, 420.66, 420.67, 420.69, and 420.70. Currently for exclusive use sites, § 417.9(c) requires a launch operator to satisfy the requirements of the public safety requirements of part 420. With proposed § 450.183, the FAA is clarifying that the only requirements from part 420 that need be conducted by an exclusive use operator is the explosive safety requirements. 6. Ground Safety: Toxic Hazards During Ground Operations
Proposed § 450.187 contains requirements for toxic hazard mitigation for ground operations. This is discussed later in the "Additional Technical Justification and Rationale" section, in the subsection on toxic hazards for flight, due to the commonality of toxic requirements for ground operations and flight.
Process Improvements
Process Improvements
A. Safety Element Approval
This proposal would modify part 414 to enable applicants to request a safety element approval in conjunction with a license application as provided in proposed part 450. Proposed § 450.39 (Use of Safety Element Approval) would allow an applicant to use any vehicle, safety system, process, service, or personnel for which the FAA has issued a safety element approval under part 414 without the FAA's reevaluation of that safety element during a license application evaluation to the extent its use is within its approved envelope. Finally, this proposal would change the part 414 term from "safety approval" to "safety element approval" to distinguish it from "safety approval" as used in parts 415, 431, and 435, and proposed part 450, because these terms, as discussed later in this section, have entirely different meanings. i. Part 414 and 415 Safety Approval Clarification
A. Safety Element Approval
As defined in current § 414.3, a safety approval is an FAA document containing an FAA determination that one or more safety elements, when used or employed within a defined envelope, parameter, or situation, will not jeopardize public health and safety or safety of property. As listed in the Act, safety elements include: (1) Launch vehicle, reentry vehicle, safety system, process, service, or any identified component thereof; or (2) qualified and trained personnel, performing a process or function related to licensed launch activities or vehicles. In contrast, parts 415, 431, and 435 reference "safety approval" to mean an FAA determination that an applicant is capable of launching a launch vehicle and its payload without jeopardizing public health and safety, and safety of property. Other chapter III parts, including parts 431 and 435, reference "safety approval" as described in part 415.
The use of identical terms in parts 414, 415, 431, and 435 to reference different meanings has caused confusion. Therefore, the FAA proposes to distinguish these terms by changing the part 414 term to "safety element approval." This proposed term more accurately reflects the substance of a part 414 safety approval of a particular element that may be used to support the application review for one or more launch or reentry licenses. Other than the addition of "element" to the current term, the part 414 definition and related references in parts 413 and 437 would remain the same. The FAA would make conforming changes throughout parts 413, 414, and 437, where a part 414 safety approval is referenced, to change those references to "safety element approval." The term "safety approval" would maintain the same meaning as that in current 415, 431 and 435 where it appears in the proposed rule. ii. Part 414 Safety Element Approval \170\ Application Submitted in Conjunction With a License Application
\170\ For readability and ease of understanding, this section refers to a current part 414 safety approval as a safety element approval, regardless of whether the discussion is referencing the current regulations or the proposed regulations. For direct quotations, the FAA retains the previous term "safety approval."
Part 414 enables a launch and reentry operator to use an approved safety element within a specified scope without a re-examination of the element's fitness and suitability for a particular launch or reentry proposal. A safety element approval may be issued independent of a license, and it does not confer any authority to conduct activities for which a license is required under chapter III. A safety element approval does not relieve its holder of the duty to comply with all applicable requirements of law or regulation that may apply to the holder's activities.
The ARC recommended that an applicant for a launch or reentry license be able to identify one or more safety elements included in the applicant's license application and to request review of those safety elements for a safety element approval concurrent with the license application review.\171\
\171\ ARC Report, p. 24-25.
The FAA agrees with the ARC's recommendation. The FAA notes that its practice has always been to accept references to information provided in a previous license application so long as the applicant can demonstrate the relevance of that information to the current application. The FAA also relies on previous evaluations where it analyzed compliance with a particular requirement if the same operator submits a more recent application using the same analysis. The proposed changes would codify this approach for safety element approval applications in proposed § 450.39 \172\ and the relevant sections in part 414.
\172\ Proposed § 450.39 is similar to § 437.21(c) for experimental permits, which states that if an applicant proposes to use any reusable suborbital rocket, safety system, process, service, or personnel for which the FAA has issued a safety approval under part 414, the FAA will not reevaluate that safety element to the extent its use is within its approved envelope. Parts 415 and 431 do not have similar sections because they were developed before part 414 was issued.
This proposal would allow an applicant to request a safety element approval as part of its vehicle operator license application. Specifically, this rule would provide a process in proposed § 414.13 to apply for a safety element approval concurrently with a license application. These safety element approval applications submitted in conjunction with a license would largely use information contained in a license application to satisfy part 414 requirements. This would alleviate the need to provide separate applications for a vehicle operator license and a safety element approval. The FAA envisions safety element approvals in conjunction with a license application to cover the same safety elements as delineated in § 414.3.
Using similar processes as for part 414, the FAA would determine whether a safety element is eligible for a safety element approval. The FAA would base its determination on criteria in proposed part 450. The applicant would be required to specify the sections of the license application that support its application for a safety element approval. The technical criteria for reviewing a safety approval submitted as part of a vehicle operator license application would be limited to the requirements of proposed part 450. This limitation would simplify the safety element approval process by eliminating the need to provide a Statement of Conformance letter, as required under current § 414.1(c)(3) for a safety element approval separate from a vehicle operator license application. To avoid this limitation to proposed part 450 criteria, an applicant could apply for a safety element approval separate from a vehicle operator license. However, there is no difference between a safety element approval issued through a separate application or a vehicle operator license application.
Finally, the FAA proposes to remove the requirement stating that, for each grant of a safety element approval, the FAA will publish in the Federal Register a notice of the criteria that were used to evaluate the safety element approval application, and a description of the criteria. The FAA provided the rationale for this notification in the preamble to a proposed rule.\173\ The FAA explained that the purpose of this notification requirement was to make clear the criteria and standards the FAA used to assess a safety element. However, the FAA has found that this requirement is unnecessary, and has potentially discouraged applications for safety element approvals due to concerns that proprietary data may be disclosed. Going forward, a safety element approval application submitted concurrently with a vehicle operator license application would be evaluated based only on criteria in proposed part 450. For other safety element approvals, experience has shown that there is no need to publish the criteria because the FAA's determinations were not based on any uniquely-derived standard. In fact, all eight safety element approvals granted by the FAA have been evaluated against regulations in 14 CFR chapter III. Therefore, the FAA proposes to revise the requirement in current § 414.35 (re-designated as § 414.39) such that safety element approval evaluation criteria, whether related to an application submitted concurrently with a license application or separately, would not require publication.
\173\ Safety Approvals, NPRM, 70 FR 32191, 32198 (June 1, 2005).
Given the FAA's proposal to not require publication of evaluation criteria, the confidentiality provision under current § 414.13(d) \174\ is no longer necessary. That provision notifies applicants that if proposed criteria is secret, proprietary, or confidential, it may not be used as a basis to issue a safety approval.
\174\ Current § 414.13 would be renumbered in this proposal as § 414.17 to maintain sequential section numbering.
B. Incremental Review of a License Application
B. Incremental Review of a License Application
In response to the ARC recommendations, the FAA proposes to amend part 413 and to include language in proposed part 450 to allow an applicant the option for an incremental review of the safety approval portion of its application.
Under 51 U.S.C. 50905(a)(1), the FAA is required by statute to issue or deny a launch or reentry license not later than 180 days after accepting an application. Under the same statute, the FAA must inform the applicant of any pending issue and action required to resolve the issue not later than 120 days after accepting an application. To ensure that the FAA has sufficient time to complete a thorough review to evaluate whether the applicant complies with the FAA's commercial space transportation regulations in the prescribed time frame, § 413.11 states the FAA screens the application to determine if it contains sufficient information for it to begin its review. It also states that if the application is so incomplete or indefinite that the FAA cannot start to evaluate it, the FAA will notify the applicant accordingly. In accordance with internal policy, the FAA aims to make this complete enough determination within two calendar weeks after receiving the application. When the FAA accepts an application, the 180-day review period begins on the date that the FAA received the application. If the FAA accepts an application as complete enough to review, the FAA works with applicants to identify additional information and documentation needed to demonstrate regulatory compliance, and advises applicants when those materials are needed. If the additional materials are not provided within an appropriate time frame, the FAA tolls the review period, stopping the counting of time towards the 180-day deadline. Once the FAA has completed its review, it issues a license, or informs the applicant, in writing, that the license application is being denied and states the reasons for denial.
Industry representatives have expressed frustration both with a lack of clarity as to what is "complete enough" for the FAA to accept an application and begin review and with the 180-day review period. The FAA seeks comment on how the FAA can improve the clarity of "complete enough" to address past frustrations. For an applicant that is in the early stages of development, there are challenges with compiling all of the documentation in parallel with their vehicle development. First-time applicants regularly underestimate the amount of time needed for licensing. For nearly all applicants, much of the vehicle and mission information is only refined and finalized within the 180-day review period, which may subject the application to tolling and business risk to the applicant's timeline for launch operations. The timing of the issuance of an FAA authorization has never caused a delay to a launch or reentry operation, but the FAA is cognizant that there could be impacts on an operator even absent an operation delay.
In part to address these issues, and bearing in mind that a written application is the means by which the FAA determines whether a launch or reentry operator can conduct a launch or reentry safely, the FAA invited the ARC to describe how the FAA might modify its application process to improve efficiency for both the FAA and applicants. The ARC suggested in part that the FAA allow for an incremental or modular application and review process. Specifically, the ARC recommended that the application review process should be modified to allow for incremental approvals of subsections to guide a focused review and avoid tolling. The recommendation suggested further that, rather than 180 days for review of an entire application, the FAA should assign a brief period for each subsection or module.
The current application process is already modular to an extent. The FAA has issued payload determinations outside of a license, primarily for payload developers seeking early assurances that their payload would be permitted to be launched. The FAA has even conducted preliminary policy reviews to provide similar assurances to future applicants on a less formal basis. Despite these allowances, the vast majority of FAA commercial space licensing evaluation time is spent on evaluating the safety implications of a license application. Because this proposed rule seeks to convert the prescriptive safety requirements to performance-based criteria, the FAA believes that it may be possible to develop a flexible safety review process that can afford applicants early determinations, providing an applicant more flexibility and control over the timing of the licensing process.
The ARC also recommended that the FAA reduce its application review time. The ARC focused on differentiating between experienced and inexperienced operators in order to decrease FAA review time of license applications. While the FAA agrees that experienced operators may require shorter application review times, it should be noted that this would likely be due to familiarity with the application process, more streamlined application materials that lend themselves to a more efficient review, and established processes that have been through FAA review previously (such as ground safety analyses).
While the proposed incremental review process would empower operators to better define when certain portions of an application are reviewed and would allow an operator that has satisfied certain requirements early to receive credit for those portions of its application in advance, other proposals in this rulemaking, such as safety element approvals concurrent with a license application, flexible time frames, and reduced application burdens, would probably serve to reduce review times more effectively than an incremental application process. Nevertheless, the modular nature of payload determinations, policy approvals, environmental evaluations, and financial responsibility requirements, and the more granular incremental review of compliance with the safety approval requirements would allow an applicant to seek partial approval of an application as soon as a portion is ready to be evaluated. These approvals would allow an operator to better manage its timeline and any potential timeline risk.
The flexible nature of this proposal would allow the FAA to further engage with industry and establish new best practices and greater efficiencies for both government evaluators and our commercial partners. The option of using an incremental approach would provide more flexibility to operators who are able to provide portions of their application in advance.
In proposed § 450.33 (Incremental Review and Determinations), the FAA would revise the launch and reentry regulations to allow for an incremental review application submission option for vehicle operator license applicants. Because the current regulations already allow an operator to submit the payload, policy, environmental, and financial responsibility portions of its application independently, the FAA proposes that the incremental review process apply specifically to the safety approval portion of a license application. Given the large variety of applicant experience, proposed operations, and company timelines, the FAA recognizes a need for flexibility. Accordingly, the FAA is proposing amendments to part 413 and regulatory language in proposed part 450 to allow for incremental application submission and determinations. This incremental review application process would not replace the traditional review of a full, complete application submitted at once--the incremental review would be an optional path to obtaining an FAA license determination that allows an applicant to choose an application submission process that suits their business model and program needs.
The FAA is proposing in § 450.33(a) that, prior to any submission, an applicant would be required to identify to the FAA that it plans to avail itself of the incremental review and determination application process. During pre-application consultation, the FAA would work with an applicant towards an incremental review process that is aligned to both the development process for an applicant and the necessities of the FAA's evaluation framework. The FAA proposes to coordinate with applicants during pre-application consultation to determine the following: (1) Appropriate portions of an operator's application that could be submitted and reviewed independently; (2) the application and review schedule with dates of key milestones; (3) the applicant's planned approach to demonstrate compliance with each applicable regulation, to include any foreseeable requests for waiver; and (4) the scope of the proposed action being applied for, the identification of any novel safety approaches or other potentially complicating factors, and how those will be addressed during the licensing process.
The details of an applicant's incremental application process would have to be approved by the FAA in accordance with proposed § 450.33(b) prior to application submission and the FAA could issue determinations towards a safety approval resulting from those reviews, in accordance with proposed § 450.33(c). An applicant would be able to propose sections of the safety approval portion of its application that the FAA could review independently. This process would allow an applicant to submit completed sections, for example the System Safety Program, to the FAA early, rather than wait until the entire application was complete enough. The FAA would also be able, where appropriate, to review and make determinations on these increments prior to a full licensing determination. It would also allow an applicant to identify more challenging or lengthy portions of an application that could be submitted earlier to avoid delays and tolling closer to a launch date. The FAA believes this process would improve predictability for applicants seeking assurances against business risks. As the FAA gains more experience with the incremental application process, the FAA may issue guidance for the process or an example of a process that has been found to satisfy the intent of the regulation.
Continue reading ↓ 600 of 1213 passages shown