Radar Vectors
Advisory Circular Current Issued Feb 14, 2023 AFS-300 130 pages Copy saved Nov 18, 2026

AC 90-89C Amateur-Built Aircraft and Ultralight Flight Testing Handbook

This AC provides suggestions and safety-related recommendations primarily to assist amateur-built aircraft and ultralight vehicle builders in developing individualized flight test plans. It also provides guidance for Experimental Light-Sport Aircraft (ELSA) flight testing after modifications to the aircraft. It provides recommendations and suggestions you can combine with other sources on test flying, such as the aircraft plan/kit manufacturer’s flight testing instructions and other flight testing data. This will help you develop a detailed flight test plan, tailored for your aircraft or ultralight vehicle and resources. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies.

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Amateur-Built Aircraft and Ultralight

Flight Testing Handbook

Date: 2/14/23 AC No: 90-89C Initiated by: AFS-300 Change:

ii

This advisory circular (AC) provides suggestions and safety-related recommendations primarily to assist amateur-built aircraft and ultralight vehicle builders in developing individualized flight test plans. It also provides guidance for Experimental Light-Sport Aircraft (ELSA) flight testing after modifications to the aircraft. It provides recommendations and suggestions you can combine with other sources on test flying, such as the aircraft plan/kit manufacturer’s flight testing instructions and other flight testing data. This will help you develop a detailed flight test plan, tailored for your aircraft or ultralight vehicle and resources.

This AC attempts to make you aware that test flying an aircraft or ultralight vehicle is a critical undertaking, which you should approach with thorough planning, skill, and common sense. The flight test plan is the heart of all professional flight testing. The plan should account for every hour spent in the flight test phase and you should adhere to it with the same respect for the unknown that all successful test pilots share. The time allotted for each phase of a personalized flight test plan may vary, and each phase may have more events or checks than suggested in this AC, but your goals, should be the same. You should add flight test operational and performance data to the Aircraft Operating Handbook (AOH) so you can reference the data prior to each flight.

This AC also provides criteria for the use of an optional, operationally centric or task-based experimental aircraft flight test plan. This task-based option provides at least the same level of safety and reliability that the existing hourly minimum 25 or 40-hour flight test provides, but with the advantages of having operational completion criteria, a plan to record data for the creation of an AOH, and a flight test report documenting the flight testing results.

The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies. This AC is not mandatory and does not constitute a regulation. This AC describes an acceptable means, but not the only means, to develop flight test plans. However, if you use the means described in the AC, you should follow it in all respects. This AC applies to amateur-built aircraft and ultralight vehicle builders, and individuals involved in flight testing those aircraft and ultralight vehicles.

Mandatory terms used in this AC such as “must” are used only in the sense of ensuring applicability of these particular methods of compliance when the acceptable means of compliance described herein are used.

Caitlin Locke Acting Deputy Executive Director, Flight Standards Service

iii

CONTENTS Paragraph Page

Chapter 1. Administrative Information … 1-1

1.1 Purpose of This Advisory Circular (AC) … 1-1 1.2 Audience … 1-1 1.3 Where You Can Find This AC … 1-1 1.4 What This AC Cancels … 1-1 1.5 Background … 1-1 1.6 Definitions … 1-2 1.7 Request for Information … 1-2 1.8 AC Feedback Form … 1-3

Chapter 2. Preparation … 2-1

Section 1. Homework … 2-1

2.1 Objective … 2-1

Section 2. Airport Selection … 2-12

2.2 Objective … 2-12

Section 3. Emergency Plans and Equipment … 2-14

2.3 Objective … 2-14

Section 4. Test Pilot … 2-17

2.4 Objective … 2-17 2.5 General … 2-17 2.6 Test Pilot Requirements … 2-17

Section 5. Medical Facts for Pilots … 2-19

2.7 Objective … 2-19

Section 6. Transporting the Aircraft to the Airport … 2-21

2.8 Objective … 2-21

Section 7. Assembly and Airworthiness Inspection … 2-22

2.9 Objective … 2-22 2.10 General … 2-22 2.11 Fitness Inspection—Airframe … 2-22 2.12 Field Check … 2-24

Section 8. Weight and Balance … 2-27

2.13 Objective … 2-27 2.14 Determining Empty Weight CG … 2-29 2.15 Determining Takeoff Weight CG … 2-30 2.16 Additional Equipment Testing … 2-31

Section 9. Paperwork … 2-32

2.17 Objective … 2-32

Section 10. Powerplant Tests … 2-34

2.18 Objective … 2-34

iv

Section 11. Additional Engine Tests … 2-39

2.19 Objective … 2-39

Section 12. Propeller Inspection … 2-43

2.20 Objective … 2-43 2.21 Recommendations for All Propellers … 2-44 2.22 Propeller Tracking Check … 2-45 2.23 Metal Propeller Inspection … 2-45 2.24 Wood Propeller Inspection … 2-47 2.25 Composite Propeller Inspection … 2-48

Chapter 3. Taxi Tests … 3-1

Section 1. Low-Speed Taxi Tests … 3-1

3.1 Objective … 3-1 3.2 Taxi Tests … 3-1

Section 2. High-Speed Taxi Tests … 3-2

3.3 Objective … 3-2

Chapter 4. The First Flight … 4-1

Section 1. General … 4-1

4.1 Objective … 4-1 4.2 General … 4-1 4.3 Recommendations … 4-1 4.4 First Flight Inspection … 4-2

Section 2. The Role of the Chase Plane … 4-3

4.5 Objective … 4-3 4.6 General … 4-3

Section 3. Emergency Procedures … 4-4

4.7 Objective … 4-4 4.8 General … 4-4

Section 4. First Flight … 4-5

4.9 Objective … 4-5

Section 5. First Flight Procedures … 4-7

4.10 Objective … 4-7

Chapter 5. The First 10 Hours … 5-1

Section 1. The Second Flight … 5-1

5.1 Objective … 5-1

Section 2. The Third Flight … 5-1

5.2 Objective … 5-1 5.3 General … 5-1

v

Section 3. Hours 4 Through 10 … 5-2

5.4 Objective … 5-2 5.5 General … 5-2 5.6 Gear Retraction … 5-2 5.7 Climbs and Descents … 5-3 5.8 Airspeed In-Flight Accuracy Check … 5-4

Chapter 6. Expanding the Envelope … 6-1

Section 1. General … 6-1

6.1 Objective … 6-1

Section 2. Hours 11 Through 20 … 6-1

6.2 Objective … 6-1 6.3 Stalls … 6-3

Section 3. Hours 21 Through 35: Stability and Control Checks … 6-6

6.4 Objective … 6-6 6.5 General … 6-6 6.6 Definitions … 6-7

Section 4. A Word or Two About Flutter … 6-11

6.7 Objective … 6-11 6.8 Description … 6-11

Section 5. Spins … 6-13

6.9 Objective … 6-13 6.10 Caution … 6-13 6.11 Planning the Flight … 6-14

Section 6. Accelerated Stalls … 6-1

6.12 Objective … 6-1

Chapter 7. Putting It All Together: 36 Hours to —————? … 7-1

Section 1. Maximum Gross Weight Tests … 7-1

7.1 Objective … 7-1

Section 2. Service Ceiling Tests … 7-2

7.2 Objective … 7-2

Section 3. Navigation, Fuel Consumption, and Night Flying … 7-3

7.3 Objective … 7-3

Chapter 8. Thoughts on Testing Canard Type Amateur-Built Aircraft … 8-1

Section 1. Canards … 8-1

8.1 Objective … 8-1

Section 2. Flight Test Considerations … 8-3

8.2 General … 8-3

vi

Chapter 9. Ultralight Airframe Inspection … 9-1

Section 1. Differences … 9-1

9.1 Objective … 9-1 9.2 Definition … 9-1

Section 2. The Test Pilot … 9-2

9.3 General … 9-2

Section 3. Preflight Airframe Inspection … 9-3

9.4 General … 9-3 9.5 Checklist … 9-3

Chapter 10. Ultralight Engine/Fuel System Inspection … 10-1

Section 1. Engine Inspection … 10-1

10.1 Objective … 10-1

Section 2. Fuel Systems … 10-3

10.2 General … 10-3

Chapter 11. Ultralight Test Flying Recommendations … 11-1

Section 1. Three Recommendations … 11-1

11.1 Objective … 11-1 11.2 Recommendations … 11-1

Section 2. Airport Selection … 11-2

11.3 Objective … 11-2

Section 3. Taxiing … 11-2

11.4 General … 11-2

Section 4. First Flight Differences … 11-2

11.5 Use of Power … 11-2 11.6 Control Feel … 11-3 11.7 Stalls … 11-3 11.8 Steep Turns … 11-3

Section 5. Emergency Procedures … 11-3

11.9 Engine Failures … 11-3 11.10 Loss of Control … 11-3 11.11 Catastrophic Failure … 11-4

Appendix A. Sample Checklist for a Condition Inspection … A-1

Appendix B. Sources for Accident/Incident Information … B-1

Appendix C. Additional References on Flight Testing … C-1

vii

List of Figures

Figure 2-1. Cumulative Portion of Phase I E-AB Accidents With Less Than

35 Airframe Hours … 2-2

Figure 2-2. Sample Flight Test Card … 2-7

Figure 2-3. Sample Maintenance Record Entry … 2-9

Figure 2-4. Runway Length Chart … 2-13

Figure 2-5. Empty Weight CG … 2-29

Figure 2-6. Takeoff CG … 2-30

Figure 2-7. Additional Equipment Added … 2-31

Figure 2-8. 100 Hp Fuel Flow Rate Chart … 2-42

Figure 2-9. Propeller Tracking … 2-45

Figure 6-1. Climb Airspeed and Altitude Graph … 6-4

Figure 6-2. Best Rate of Climb Speed Graph … 6-5

Figure 6-3. Static Stability … 6-7

Figure 6-4. Time … 6-8

CHAPTER 1. ADMINISTRATIVE INFORMATION › 1.5 Background.

CHAPTER 1. ADMINISTRATIVE INFORMATION

1.1 Purpose of This Advisory Circular (AC). This AC provides suggestions and safety-related recommendations primarily to assist amateur-built aircraft and ultralight vehicle builders in developing individualized flight test plans. It also provides guidance for Experimental Light-Sport Aircraft (ELSA) flight testing after modifications to the aircraft. It provides recommendations and suggestions you can combine with other sources on test flying, such as the aircraft plan/kit manufacturer’s flight testing instructions and other flight testing data. This will help you develop a detailed flight test plan, tailored for your aircraft or ultralight vehicle and resources. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies.

1.2 Audience. This AC applies to amateur-built aircraft and ultralight vehicle builders, owners, and operators developing individualized aircraft flight test plans. It also provides guidance to owners and operators of ELSAs performing flight testing after making modifications to the aircraft.

1.3 Where You Can Find This AC. You can find this AC on the Federal Aviation Administration’s (FAA) website at https://www.faa.gov/regulations_policies/advisory_cir culars and the Dynamic Regulatory System (DRS) at https://drs.faa.gov.

1.4 What This AC Cancels. AC 90-89B, Amateur-Built Aircraft and Ultralight Flight Testing Handbook, dated April 27, 2015, is canceled.

1.5 Background. We, the FAA, along with the Experimental Aircraft Association (EAA), and the United States Ultralight Association (USUA), are concerned and committed to improving the safety record of amateur-built aircraft and ultralight vehicles. Past FAA Administrator, T. Allen McArtor, and past EAA President, Paul H. Poberezny, signed a Memorandum of Agreement (MOA) on August 1, 1988, addressing the need for educational and safety programs to help amateur builders test fly their aircraft. This AC lists guidelines for flight testing amateur-built aircraft, using suggestions in the MOA. We have revised this AC to include flight testing recommendations for canard type aircraft and ultralight vehicles as part of our continuing efforts to improve the safety record of all types of general aviation aircraft. In 2012 the first Loss of Control Working Group (LOCWG) investigated the causal factors behind fatal accidents arising from a loss of control during the approach and landing phases of flight. Loss of control is the leading cause of fatal accidents in general aviation. From a study of a random sample of 90 fatal accidents fitting this profile over the past decade the Working Group recommended 27 safety enhancements (SE), 23 of which were approved. SE-23 is implemented into this AC. As a result of SE-23, there are two major additions to this AC.

• The Type Club Coalition (TCC) coordinated by the EAA developed a best practices guide for when flight tests should be done following a modification to an amateur-built aircraft.

• Testing for center-of-gravity (CG) limits, including lateral, was added to this AC.

1.5.1 Two informational FAA updates were added.

1.7 Request for Information. › Washington, DC 20024

• Light-sport aircraft (LSA) flight testing after a modification is mentioned where appropriate within this AC.

• All references to two seat ultralights have been removed.

1.6 Definitions. The following terms are defined for use in this AC.

1.6.1 Aircraft. In this AC, refers to an amateur-built aircraft, special light-sport category aircraft (SLSA), or ELSA.

1.6.2 Amateur-Built Aircraft. An aircraft issued an Experimental Certificate under the provisions of Title 14 of the Code of Federal Regulations (14 CFR) part 21, § 21.191(g).

1.6.3 Experimental Light-Sport Aircraft (ELSA). An aircraft issued an Experimental Certificate under the provisions of § 21.191(i).

1.6.4 Light-Sport Aircraft. An aircraft that meets the parameters of the definition of light-sport aircraft specified in 14 CFR part 1, § 1.1.

1.6.5 Special Light-Sport Aircraft (SLSA). An aircraft issued a Special Airworthiness Certificate in the light-sport category under the provisions of § 21.190.

1.6.6 Ultralight Vehicle. A vehicle that meets the requirements of 14 CFR part 103, § 103.1.

1.7 Request for Information. We have designed this AC as a reference document to help prepare a flight test plan for an amateur-built aircraft or ultralight vehicle. The suggestions and recommendations in Chapters 2 through 7 are for conventionally designed aircraft with an air-cooled, 4-cycle, reciprocating engine developing less than 200 horsepower (hp) and with a fixed-pitch propeller.

• Chapter 8 deals with flight testing recommendations for canard aircraft.

• Chapters 9 through 11 address flight testing considerations for ultralight vehicles under part 103.

1.7.1 Because of many existing amateur-built aircraft/ultralight vehicle designs and new designs being introduced each year, we encourage public participation in updating this document. Send comments, suggestions, or information about this AC to the following address:

U.S. Department of Transportation Federal Aviation Administration Flight Standards Service General Aviation Group (AFS-340) 5th Floor, 950 L’Enfant Plaza, S.W. Washington, DC 20024

CHAPTER 1. ADMINISTRATIVE INFORMATION › 1.8 AC Feedback Form.

Note: After a review, appropriate comments, suggestions, and information may be included in the next revision of this AC.

1.8 AC Feedback Form. For your convenience, the AC Feedback Form is the last page of this AC. Note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this AC on the Feedback Form.

2.1.1 Phased Flight Testing. › 2.1.1.1 The data gathered during flight testing should be used to…

CHAPTER 2. PREPARATION

SECTION 1. HOMEWORK

2.1 Objective. A planned approach to flight testing.

2.1.1 Phased Flight Testing. After the Special Airworthiness Certificate and operating limitations have been issued, the builder of an amateur-built aircraft shows compliance with Title 14 of the Code of Federal Regulations (14 CFR) part 91, § 91.319(b), that the aircraft is controllable throughout its normal range of speeds and throughout all the maneuvers to be executed and that the aircraft has no hazardous operating characteristics or design features. This is accomplished through a “phased” flight test approach (Phase I and Phase II). In Phase I operations, the aircraft undergoes flight testing to ensure the proper operation and reliability of aircraft systems and to develop the aircraft’s flight envelope. After the completion of Phase I, the aircraft enters Phase II where it will normally reside for the remainder of its operational life, unless modifications are made to the aircraft, in which case it re-enters Phase I testing. The aircraft then re-enters Phase II upon completion of that further testing. This cycle continues for the life of the aircraft.

2.1.1.1 The data gathered during flight testing should be used to develop an accurate and complete Aircraft Operating Handbook (AOH) and to establish emergency procedures. Additional guidance on the development of the AOH can be found in Federal Aviation Administration (FAA) Advisory Circular (AC) 60-6, Airplane Flight Manuals (AFM), Approved Manual Materials, Markings, and Placards – Airplanes, and AC 25.1581-1, Airplane Flight Manual.

2.1 Objective. A planned approach to flight testing. › 2.1.4 Objective of a Flight Test Plan.

Note: Industry-developed task-based test manuals may assist aircraft builders through the testing process, such as the Experimental Aircraft Association (EAA) Flight Test Manual referred to in Appendix C, Additional References on Flight Testing.

2.1.2 The First Few Hours Pose the Highest Risk. In 2011, the National Transportation Safety Board (NTSB) issued a report on the safety trends in amateur-built aircraft, noting that the principal causes of accidents lie in pilot loss of control or engine failures and, interestingly, not from builder quality of construction issues. Furthermore, FAA data shows the highest rate of accidents occurs in the first 8 hours of Phase I flight testing and then decreases dramatically. This highlights the importance of a detailed, comprehensive flight test plan of adequate or appropriate length.

Figure 2-1. Cumulative Portion of Phase I E-AB Accidents With Less Than

35 Airframe Hours

2.1.3 Develop a Flight Test Plan. Your most important task is to develop a comprehensive flight test plan. You should tailor this plan to define the aircraft’s specific level of performance, so it’s important that the entire flight test plan be developed and completed before the aircraft’s first flight.

Note: As part of the comprehensive flight test plan, the test pilot should read and comprehend this entire AC before proceeding in accomplishing any suggested task.

2.1.4 Objective of a Flight Test Plan. The objective of a flight test plan is to determine the aircraft’s controllability throughout all the maneuvers and to detect any hazardous

2.1.6 Task-Based Flight Test Plan. › 2.1.6.2 Expectations.

operating characteristics or design features. You should use this data to develop a flight manual that specifies the aircraft’s performance and defines its operating envelope. Additionally, the plan should reference the use of checklists to assure that all relevant steps and elements are covered.

2.1.5 Time Required for Flight Testing Amateur-Built Aircraft. Your original issued experimental certificate should be limited to operation within an assigned flight test area for a minimum of 25 hours when a type certificated (TC) engine/propeller combination is installed. A minimum of 40 hours is required when a non-TC’d engine, propeller, or engine/propeller combination is installed. Furthermore, if the TC’d engine, propeller, or engine/propeller combination installed has been altered in a way that differs from an approved type design in a Type Certificate Data Sheet (TCDS), a minimum of 40 hours will be required.

2.1.6 Task-Based Flight Test Plan. Comprehensive guidance on flight testing objectives has historically been lacking for amateur-built aircraft, with the only well-known requirement simply being the 25- or 40-hour flight testing requirement found in the operating limitations issued with the aircraft’s experimental certificate. This can lead to gaps in the performance and reliability testing of an aircraft, inadequate documentation of flight characteristics, and also the creation of a hazard for inexperienced pilots attempting to “just fly off” the required hours. Many times, AOHs are not created from the flight tests, resulting in little or no documented aircraft data for operators other than the original builder’s experience with flight testing.

2.1.6.1 Use of a Task-Based Flight Test Plan. The FAA has been shifting to more performance-based rules and policy, which has led to allowances for performance-based criteria in experimental aircraft flight testing. The minimum 25- or 40-hour flight test period has long been considered necessary to ensure that the aircraft and its systems are properly and thoroughly tested, found to be reliable, that the aircraft does not exhibit any undesirable flight characteristics or system flaws, and that it is tested throughout its intended flight regime. This AC creates the ability for builders to utilize a comprehensive, individualized task-based flight test plan to meet the objectives of the flight test, but according to certain completion criteria and possibly less than the typical 25 or 40 hours, depending on the complexity of the aircraft.

2.1.6.2 Expectations. The ability to use the task-based flight test plan as provided in this AC is enabled via the issuance of an operating limitation that allows its use, in lieu of the minimum 25- or 40-hour flight test periods contained in previously issued operating limitations. The FAA will permit the use of a task-based flight test plan based on your use of this AC and adherence to the objectives of the task-based flight test plan, providing the specified logbook entry, and maintaining the AOH on board the aircraft following flight testing. No formal FAA acceptance process is necessary for the builder to utilize a task-based flight test plan. Issuance of operating limitations with the traditional minimum hourly flight test periods specified for a pilot to flight test

2.1 Objective. A planned approach to flight testing. › 2.1.8 Minimum Flight Test Plan Elements.

their aircraft as the sole occupant of the aircraft during Phase I remains for those who choose to do so in accordance with those operating limitations. There is no requirement to create, submit, or use a formal flight test plan. However, the FAA strongly encourages amateur builders to develop and utilize an individualized, comprehensive, requirements-based, operationcentric (task-based) flight test plan appropriate for the complexity of the aircraft with specific tasks and objectives. The FAA also encourages builders to utilize the Additional Pilot Program (APP) described in AC 90-116, Additional Pilot Program for Phase I Flight Test. A task-based flight test plan should contain the minimum elements described in this AC, provide aircraft systems reliability and flight envelope testing to ensure that the aircraft is controllable throughout its normal range of speeds and throughout all the maneuvers to be executed, and ensure that the aircraft has no hazardous operating characteristics or design features. The FAA expects that builders follow their flight test plan, including those who utilize a task-based flight test plan.

2.1.7 Task-Based Flight Testing Criteria. There are three overall considerations for a successful task-based flight test plan:

• Aircraft preparation;

• Flight testing; and

• Development of an aircraft-specific AOH.

2.1.7.1 Documentation and recordkeeping are critical to each of these elements, starting with the builder’s log, continuing with ongoing aircraft maintenance records, and then recording any modifications made to the aircraft during its life. The goals of operational flight testing are to develop the performance and qualitative handling data that will be compiled in the AOH, ensure aircraft systems reliability, determine the aircraft’s flight envelope to ensure that the aircraft is controllable throughout its normal range of speeds and maneuvers, and ensure that the aircraft has no hazardous operating characteristics or design features.

2.1.8 Minimum Flight Test Plan Elements. The following elements, at a minimum, should be included in a flight test plan:

1. A complete, detailed flight test plan that will:

a. Ensure the aircraft will be adequately tested and determined to be safe to fly

within the aircraft’s flight envelope, and

b. Produce flight test data to develop an accurate and complete AOH and to establish

emergency procedures.

2. Aircraft fuel system functional test procedures, fuel flow, and unusable fuel tests.

3. A fuel system functional test report. (It is recommended that the fuel system functional test report be included in the AOH. For more information, see Paragraph 2.12.3, Fuel System.)

4. Provisions for the use of electronic data recordings from electronic flight displays, engine instruments, or other recording devices in development of performance data and AOH information, if the aircraft is equipped with these types of instrumentation.

5. The method that will be used for recordkeeping.

6. The description of the cockpit layout.

7. Weight and Balance (W&B) information and calculations.

8. The aircraft inspection checklist.

9. Engine run and taxi tests.

10. The following flight tests:

a. First flight.

b. Gear and flap operation.

c. Rough pitot-static check.

d. Wings level stalls.

e. Accelerated stalls.

Note: In cases where stalling the specific aircraft type is not recommended, investigating approaches to stall and stall warning in the cited configurations can be substituted if appropriate.

f. Determine best angle of climb (VX) and best rate of climb (VY) speed.

g. Best glide speed.

h. Range and endurance.

i. Takeoff performance.

j. Longitudinal control.

k. Trim effectiveness.

l. Static longitudinal stability.

m. Static directional stability.

n. Static lateral stability.

o. Longitudinal dynamic stability.

p. Runaway electric pitch trim, if applicable.

q. Landing performance.

11. Flight test cards. The task-based flight test plan should contain “flight test cards” that can be used to document results of flight test procedures and provide for the

collection and recording of flight test data. A sample flight test card is shown in Figure 2-2. Flight test cards should contain at least the following:

a. Date.

b. Aircraft N-Number or serial number.

c. Location (Airport ID) for takeoff and landing.

d. Start time, takeoff time, landing time, and shutdown time.

e. Name of the Builder/Owner Pilot (BP) and Additional Qualified Pilot (QP), if

applicable.

f. Flap setting for takeoff and landing, if applicable.

g. Name of observer, if applicable.

h. Takeoff weight and center of gravity (CG).

i. Takeoff fuel quantity.

j. Planned duration of flight.

k. Planned landing fuel quantity.

l. Altimeter setting.

m. Objectives for each flight test element.

n. Risk level or risk designation for each flight test element.

o. Specific procedures for each flight test element:

• Power settings.

• Flap settings, if applicable.

• Landing gear position.

p. Emergency preparedness measures necessary and specific to each element.

q. Acceptable or satisfactory completion criteria or outcomes for each flight test

element.

r. Comments and results for each flight test element.

Figure 2-2. Sample Flight Test Card

2.1 Objective. A planned approach to flight testing. › 2.1.10 Exit Criteria—Aircraft Maintenance Record Documentation of…

OPERATING LIMITATIONS.

Process. Builders may utilize a task-based flight test plan without approval or submission to the Flight Standards District Office (FSDO) or Manufacturing Inspection District Office (MIDO). FAA acceptance will be conveyed by issuance of the Experimental Certificate and corresponding operating limitations. Any change to the hourly requirements for flight testing will also be reflected in the aircraft’s operating limitations.

Required Operating Limitation. In order to utilize a task-based flight test plan, the operating limitations for the aircraft need to reference this AC. The limitation that authorizes the use of the task-based flight test plan is worded as, or worded similarly to, the following:

All flights must be in this geographical area: [The area must be described by radius, coordinates, navigational aids, and/or landmarks. The size of the area and airports must be that required to safely conduct the anticipated maneuvers and tests.] Unless operating in accordance with the task-based flight test program described in Advisory Circular (AC) 90-89, Amateur-Built Aircraft and Ultralight Flight Testing Handbook, chapter 2, section 1, during Phase I flight testing, this aircraft must be operated for at least … hours with at least … takeoffs and landings.

2.1.9 Failure to Meet Flight Testing Criteria. If at any time during the flight testing of the aircraft, the aircraft, its systems, or operational elements are unable to meet the completion criteria originally prescribed in the task-based flight test plan, make repairs as needed and repeat the procedure until completion criteria is met or test for the full 25 or 40 hours, as appropriate, according to the applicable operating limitations. Operating limitations generally will not be reissued. The desired outcome is to ensure that the aircraft is controllable throughout its normal range of speeds and throughout all the maneuvers to be executed and that the aircraft has no hazardous operating characteristics or design features.

2.1.10 Exit Criteria—Aircraft Maintenance Record Documentation of Completion of Requirements-Based Phase I Flight Test. The builder should make a maintenance record entry attesting that the flight test has been completed, and the data has been recorded. This ensures that the flight test was completed based on the prepared plan and also allows retention of the flight test data in the AOH for a particular aircraft.

2.1 Objective. A planned approach to flight testing. › 2.1.12 Best Practices for Flight Testing After Modifying an…

Figure 2-3. Sample Maintenance Record Entry

The logbook entry documenting completion of the flight test will correspond to the following:

Completion of task-based flight test:

“I certify that all requirements of the task-based flight test plan have been completed in accordance with AC 90-89 and the aircraft is controllable throughout its normal range of speeds and throughout all maneuvers to be executed, has no hazardous operating characteristics or design features, and is safe for operation. An AOH has been developed and placed in the aircraft. The following aircraft operating data has been demonstrated during the flight testing: speeds VS0 … , VX … , and VY … , and the weight … and CG location … at which they were obtained.”

Printed Name Signature

Hours-based flight test completion only:

“I certify that the prescribed flight test hours have been completed and the aircraft is controllable throughout its normal range of speeds and throughout all maneuvers to be executed, has no hazardous operating characteristics or design features, and is safe for operation. The following aircraft operating data has been demonstrated during the flight testing: speeds VS0 … , VX … , and VY … , and the weight … and CG location … at which they were obtained.”

Printed Name Signature

2.1.11 Time Required for Flight Testing Experimental Light-Sport Aircraft (ELSA). If you own an ELSA certificated under 14 CFR part 21, § 21.191(i)(2), and it has not been modified, conduct a test flight as per the operations manual in an assigned flight test area for a minimum of 5 hours. This applies for all categories and classes of light-sport aircraft (LSA) to determine aircraft controllability throughout its design limits.

2.1.12 Best Practices for Flight Testing After Modifying an Experimental Amateur-Built (E-AB) Aircraft. Before considering any modification to an aircraft previously issued an experimental certificate for the purpose of operating amateur-built aircraft, there are two things you need to consider. First is the level of modification; the other is the corresponding flight testing required for the modification. When considering the level of modification, you should first check the E-AB operating limitations. They will detail what, if any, reporting requirements there are for a given modification. This is especially important when the E-AB modification approaches the same level of a major change to the type design of a type certificated aircraft as defined in § 21.93. Usually the owner of the E-AB aircraft is required by the aircraft operating limitations to notify the responsible

2.1.12 Best Practices for Flight Testing After Modifying an… › 2.1.12.4 If the major change includes installing a different type of…

FSDO following a “major change” as defined by § 21.93. This regulation states that a minor change is “one that has no appreciable effect on the weight, balance, structural strength, reliability, operational characteristics, or other characteristics affecting the airworthiness of the product.” All other changes are “major changes.” According to the operating limitations issued for the aircraft, the corresponding flight testing for a major change will require at least 5 hours minimum of supplemental Phase I flight testing be completed to comply with § 91.319(b). The aircraft owner then obtains concurrence from the FSDO as to the suitability of the proposed test area.

2.1.12.1 Flight testing in some form is advisable following any modification to the aircraft. Not only will a structured series of test flights reveal any malfunctions or unintended consequences associated with a modification, but it will also allow the pilot to become familiar with the operation of the aircraft after a given change before returning to “operational” flying. For example, flight testing a new instrument will verify its proper operation and ensure the pilot understands how to use it. This is important to accomplish before operating the aircraft in a situation where the proper operation of the instrument may affect the safe outcome of a flight.

2.1.12.2 Flight testing after a modification that is not considered a major change is at the sole discretion of the owner or pilot, so it may or may not be as formal as Phase I. In general, however, the owner or pilot should conduct it in uncongested airspace local to an airport, to keep distractions at a minimum. Carrying passengers not involved with the flight test should be avoided; however, because this is not Phase I testing, a passenger may be carried to monitor aircraft systems or perform other functions relevant to the purpose of the flight, if appropriate. As with any test flight, there should be a clear plan with clear objectives.

2.1.12.3 It is important to note that, while some modifications are neither mandatory nor necessary to report to the FSDO, you should document all changes appropriately. The aircraft maintenance records should be updated with the date the work was completed, the hours in service of the components affected, and the total hours on the aircraft noted in the records along with the changes performed and the equipment added or removed. The aircraft’s W&B data and equipment list should also be updated. Note the areas that affect operational differences in the flight manual. In situations where the changes affect installed or required placards and decals, they should be in place before flying with the new configuration.

2.1.12.4 If the major change includes installing a different type of engine (e.g., reciprocating to turbine) or a change of a fixed-pitch propeller from or to a controllable pitch propeller, the aircraft owner completes a revised FAA Form 8130-6, Application for U.S. Airworthiness Certificate, to update the aircraft’s file in the FAA Aircraft Registration Branch. All operations are to be conducted under day visual flight rules (VFR) and over sparsely populated

2.1.13 Modifying ELSAs. › 2.1.13.2 Following any major change, your ELSA is assigned to a flight…

areas. The aircraft remains in flight test for a minimum of 5 hours as specified in the operating limitations issued for the aircraft.

2.1.12.5 At the completion of flight testing, a statement with the results should be posted in the aircraft maintenance records. Changes should be incorporated into the AOH and other affected records. The statement should, at a minimum, state the scope of the changes, the tests performed along with the results. The total hours as of that date on the aircraft should be included, and the aircraft declared to be in a condition for safe operation.

2.1.13 Modifying ELSAs. All alterations, modifications, and additions or deletions to your ELSA are approved in writing by the LSA kit manufacturer and recorded in the aircraft records before issuance of your aircraft’s experimental certification for the purpose of operating LSA under § 21.191(i)(2).

2.1.13.1 Additionally for a major change to your ELSA (such as an alteration, modification, addition, or deletion), the FAA has the authority under § 91.319(i) to modify your ELSA operating limitations with special restrictions for flight testing due to the aircraft modification.

2.1.13.2 Following any major change, your ELSA is assigned to a flight test area for an appropriate time to conduct a flight test and evaluate that your aircraft is in a condition for safe operation. The guidance baseline for this testing is 5 hours of flight time within the flight test area. The FAA may prescribe any additional limitations and/or flight time within the flight test area deemed necessary in the interest of safety.

2.2 Objective. To select an airport to test fly the aircraft. › 2.2.3 Ideal Runway.

SECTION 2. AIRPORT SELECTION

2.2 Objective. To select an airport to test fly the aircraft.

2.2.1 Flight Test Areas. It is important to remember the requirements of § 91.305, which require that no person may flight test an aircraft except over open water or sparsely populated areas having light air traffic.

2.2.2 Runway Alignment. The airport should have one runway aligned into the prevailing wind with no obstructions on the approach or departure end. Hard surface runways should be in good repair and well maintained to avoid foreign object damage (FOD) to the propeller and landing gear. Grass fields should be level with good drainage. Avoid airports in densely populated or developed areas and those with high rates of air traffic. The runway should have the proper markings with a windsock or other wind direction indicator nearby.

2.2.3 Ideal Runway. The ideal runway at sea-level elevation should be at least 4,000 feet long and 100 feet wide. For each 1,000-foot increase in field elevation, add 500 feet to the runway length. If testing a high-performance aircraft, the airport’s runway at sea level should be more than 6,000 feet long and 150 feet wide for a wider margin of safety. You should factor other considerations, such as power-to-weight ratio, wing design, and density altitude, into the equation for picking the best runway for the initial flight testing. You can also use the chart in Figure 2-4.

2.2 Objective. To select an airport to test fly the aircraft. › 2.2.7 Safety.

Figure 2-4. Runway Length Chart

Takeoff Distance in feet

A - Distance to takeoff at minimum smooth lift-off speed, fly for 5 seconds at that speed without climbing, land, and stop straight ahead. B - Distance to reach minimum smooth lift-off speed. C - Distance covered in 5 seconds of flight at minimum smooth lift-off speed. D - Distance to stop from minimum smooth lift-off speed (includes air and ground distance). E - Distance to takeoff at slow approach speed and climb thereafter at an angle of 1 in 20 to 50 ft. altitude, this distance will allow most airplanes to accelerate to normal climb speed before crossing end of runway.

2.2.4 Emergency Fields. Identify emergency landing fields located within gliding distance from anywhere in the airport pattern altitude. Since engine failures are second only to pilot error as the major cause of amateur-built aircraft accidents, preparations for this type of emergency should be a mandatory part of the flight test plan.

2.2.5 Communications. You should perform flight tests from an airport with an active Universal Communications frequency (UNICOM) or tower, even if the aircraft either doesn’t have an electrical system or doesn’t have a radio. Even at an uncontrolled field, you should develop a communications base. For both situations, the FAA recommends a handheld radio with aviation frequencies and a headset with a microphone and a push-to-talk switch. Good radio communications improves the overall level of safety and reduces cockpit workload.

2.2.6 Physical Space. The FAA recommends you also consider the availability of hangar space and ramp areas. These facilities will provide protection from inclement weather and vandalism while the aircraft is being tested, maintained, and inspected.

2.2.7 Safety. The airport should have a telephone and firefighting equipment complying with relevant municipal codes.

2.3 Objective. › 2.3.2 Ground Emergencies.

2.2.8 Local Management. Explain the flight test program and emergency plans to the airport manager or owner who may help you obtain temporary hangar space, provide ground/air communications, and supply emergency equipment for use during the flight test.

SECTION 3. EMERGENCY PLANS AND EQUIPMENT

2.3 Objective. To develop a flight test plan with two sets of emergency plans; one for in-flight emergencies and another for ground emergencies.

2.3.1 In-Flight Emergencies. Your in-flight emergency plan should address the following:

1. Complete or partial engine failure, especially after takeoff.

2. Flight control problems and severe out-of-rig conditions.

3. Fire in the engine compartment or cockpit.

2.3.2 Ground Emergencies. The ground emergency plan should train the ground crew and/or airport fire department crash crew on, as applicable:

1. The aircraft canopy or cabin door latching mechanism.

2. The pilot’s shoulder harness/seatbelt release procedure.

3. The location and operation of the fuel shut-off valve.

4. The master switch location and its OFF position.

5. The magneto switch location and its OFF position.

6. Engine cowling removal procedures to gain access to the battery location or for firefighting.

7. The battery location and disconnect procedures.

8. Fire extinguisher application and use.

9. How to secure a ballistic parachute system.

2.3 Objective. › 2.3.8 Pilot Protection.

2.3.3 Ground Crew. A minimum ground crew of two experienced persons should support every test of an amateur-built aircraft. Your ground crew’s function is:

1. To ensure that the aircraft is in airworthy condition for safe operation.

2. To provide assistance to the test pilot in an emergency.

2.3.4 The Airport.

2.3.4.1 If the airport does not have a fire rescue unit, the FAA suggests the ground crew have a four-wheel-drive vehicle equipped with a portable radio, first aid kit, metal-cutting tools, and a fire extinguisher. At least one person should have completed first aid training.

2.3.4.2 If the airport provides a fire rescue unit, the test pilot should ensure the rescue unit and the ground crew are trained and competent in performing ground emergency functions as identified in the flight test plan.

2.3.4.3 For a small donation, some local volunteer fire and rescue companies may provide standby crew during the initial critical portions of the flight test phase.

2.3.5 Hospital Location. The ground crew should know the location and telephone numbers of the hospitals and fire rescue squads in the vicinity of the airport and the flight test area. If the test pilot is allergic to specific medications, or has a rare blood type, the test pilot should carry or wear a medical alert bracelet or card to alert medical personnel of the condition.

2.3.6 Fire Extinguisher. Fire extinguishers should be available to the ground crew, and a fire extinguisher should be securely mounted in the cockpit within easy reach of the test pilot. A fire axe, or other tool capable of cutting through the canopy, also should be in the cockpit.

2.3.7 Fire Protection. There is always danger of a flash fire during test flights. To prevent burns, the pilot should wear an aviation/motorcycle helmet, NOMEX coveralls/gloves, and smoke goggles. If NOMEX clothing is not available, cotton or wool clothing will offer some protection from heat and flames. Pilots should never wear nylon or polyester clothing because synthetic materials melt when exposed to heat and will stick to the skin.

2.3.8 Pilot Protection. A modern aviation/motorcycle helmet, a properly installed shoulder harness, a well-designed seat, a clean cockpit design free of protruding components/sharp

2.3.10 Ballistic Parachutes. › 2.3.10.2 Installation Considerations.

edges, NOMEX clothing, smoke goggles, and a memorized emergency plan ensure safety during flight testing.

2.3.9 Parachute. The decision to wear a parachute depends on the type of aircraft you are testing. Some aircraft have forward hinged canopies without quick release pins, or have pusher propellers, increasing the chance of injury to the pilot while exiting the aircraft. Other aircraft designs may pose no exit problems. If the pilot decides to wear a parachute, check that a qualified parachute rigger has packed the parachute within 180 days. Ensure that the parachute has not been exposed to rain/moisture and, when worn, does not interfere with cockpit management. The test pilot should be thoroughly trained on how to exit the aircraft and deploy the parachute.

2.3.10 Ballistic Parachutes. Ballistic parachutes are the latest development in dealing with in-flight emergencies. A ballistic parachute is attached to the aircraft and when activated, lowers the whole aircraft and the pilot to the ground at the rate of descent of about 20 feet per second or about 1,200 feet per minute.

2.3.10.1 Deployment Scenarios. You might deploy a ballistic parachute in case of:

1. Structural failure.

2. Mid-air collision.

3. Stall/spin.

4. Loss of control/icing.

5. Engine failure over bad terrain.

6. Pilot incapacitation.

2.3.10.2 Installation Considerations. You should consider the following when installing a ballistic parachute:

1. Match the parachute to the aircraft’s size, weight, and never-exceed speed (VNE). Check with the parachute manufacturer.

2. How to position and mount the parachute.

3. The parachute’s effect on the aircraft’s W&B before deployment and aircraft’s touchdown attitude after deployment.

4. Compatibility of the opening loads and the aircraft’s structural design limits.

5. The routing of the bridle and harness.

6. The routing of the activating housing.

7. The placement of the activating handle in the cockpit.

8. Incorporation of parachute deployment procedures in the in-flight emergency plan and emergency checklist.

9. The deployment time, from activation to full parachute opening.

2.6.3 Pilot Recommendations. The test pilot should: › 2.6.3.2 Talk with and, if possible, fly with a pilot in the same kind…

2.3.10.3 Inspection Recommendations. If a ballistic parachute is installed, the builder should add the appropriate ballistic parachute inspection items to the aircraft’s preflight inspection checklist. The builder also should add the ballistic parachute manufacturer’s repack/refitting schedule and maintenance inspections to the flight manual and the annual condition inspection checklist.

SECTION 4. TEST PILOT

2.4 Objective. Select a qualified individual as the test pilot.

2.5 General. The test pilot should be competent in an aircraft of similar configuration, size, weight, and performance to the test aircraft.

2.6 Test Pilot Requirements.

2.6.1 Minimum Qualifications. A test pilot should meet the following minimum qualifications:

1. Physically fit: Test flying an aircraft is a stressful and strenuous task.

2. No alcohol or drugs in the last 24 hours.

3. Rated, current, and competent in the same category and class as the aircraft being tested.

4. Current medical and biennial or flight review as appropriate, or a current United States Ultralight Association (USUA) certification and flight review, if flight testing an ultralight vehicle.

2.6.2 Suggested Test Pilot Flight Time Experience. Each test pilot assesses if their level of competency is adequate, or if additional flight training is necessary. If you determine you are not qualified to flight test an unproven aircraft, find someone who is qualified. The following suggested number of flight hours is only an indication of pilot skill, not an indicator of pilot competence.

1. One hundred hours solo time before flight testing a kit plane or an aircraft built from a time-proven set of plans.

2. Two hundred hours solo time before flight testing a unique design or high-performance aircraft.

3. A minimum of 50 takeoffs and landings within the preceding 90 days in a tailwheel aircraft if the test aircraft is tailwheel equipped.

2.6.3 Pilot Recommendations. The test pilot should:

2.6.3.1 Be familiar with the airport and the surrounding terrain that could be used for emergency landing fields in the area.

2.6.3.2 Talk with and, if possible, fly with a pilot in the same kind of aircraft to be tested; to facilitate the receipt of type-specific training in these aircraft, the EAA maintains a list by state of instructors who hold a Letter of Deviation

2.6.3 Pilot Recommendations. The test pilot should: › 2.6.3.12 Use checklists for both normal and emergency actions and procedures.

Authority (LODA). The experimental aircraft model used by the instructor for the purposes of type-specific training is also listed. This list changes often and can be found at https://www.eaa.org/eaa/pilots/letters-of-deviation-authorityholders-loda-holders.

2.6.3.3 Take additional instruction in similar TC’d aircraft, as addressed in AC 90-109, Transition to Unfamiliar Aircraft. For example, if the aircraft to be tested is tailwheel equipped, a Bellanca Citabria or Super Cub may be appropriate for training. For testing an aircraft with a short wingspan, the Grumman American Yankee or Globe Swift may be suitable for training.

2.6.3.4 For amateur aircraft built from commercial kit manufacturers, consider using an additional pilot, as referenced in AC 90-116.

2.6.3.5 Be considered competent when the test pilot has demonstrated a high level of skill in all planned flight test maneuvers in aircraft with performance characteristics similar to the test aircraft.

2.6.3.6 Study the ground and in-flight emergency procedures developed for the aircraft and practice them in aircraft with similar flight characteristics.

2.6.3.7 Have logged a minimum of 1 hour of training in recovery from unusual attitudes within 45 days of the first test flight.

2.6.3.8 Have logged a minimum of 10 tailwheel takeoff and landings within the past 30 days, if appropriate.

2.6.3.9 Study the performance characteristics of the aircraft to be tested. Refer to the designer’s or kit manufacturer’s instructions, articles written by builders of the same make and model aircraft, and study actual or video tape demonstrations of the aircraft.

2.6.3.10 Review the FAA and NTSB accident reports for the same make and model aircraft to be aware of problems the aircraft has experienced during previous operations (see Appendix B for the address).

2.6.3.11 Memorize the cockpit flight controls, switches, valves, and instruments. A thorough knowledge of the cockpit will result in controlled and coordinated mental and physical reactions during emergencies.

2.6.3.12 Use checklists for both normal and emergency actions and procedures. The Emergency procedures should be also memorized. Add additional notes on the instrument panel to aid in their use if necessary.

Note: The EAA has developed a Flight Advisor Program which offers builders/pilots assistance in performing a self-evaluation of the flight test program and/or selection of the test pilot. To obtain additional

2.7.6 Ear and Sinus Pain. › 2.7.6.1 Ear and sinus pain is usually caused by the eardrum or sinuses…

information, refer to the following EAA web page: https://www.eaa.or g/eaa/aircraft-building/volunteer-assistance/eaa-flight-advisors.

SECTION 5. MEDICAL FACTS FOR PILOTS

2.7 Objective. Identify well-known medical causes for aircraft accidents and stress the importance of a personal preflight checklist in addition to an aircraft preflight checklist.

2.7.1 Alcohol. Test flying an aircraft places additional mental and physical demands on the pilot. In addition to the 8-hour requirement of § 91.17, the FAA strongly recommends a minimum of 24 hours between the last drink and the test flight. This is because small amounts of alcohol in the bloodstream can affect judgment and reaction time, and decrease a pilot’s tolerance to hypoxia.

2.7.2 Anesthetics. Local and dental anesthetic can affect a pilot’s performance in many adverse ways. The FAA recommends that a minimum of 48 hours elapse from the time of anesthesia to the time the pilot climbs into the cockpit.

2.7.3 Blood Donations. If you donate 1 unit or 500 mL of blood or less, the FAA recommends that you do not pilot an aircraft for 24 hours; if you give more than 1 unit or more than 500 mL, the FAA recommends that you do not pilot an aircraft for 72 hours. Although the physical effects may not be noticeable at sea level, they will become apparent when flying at higher altitudes.

2.7.4 Carbon Monoxide (CO). CO is a colorless, odorless, tasteless gas that is always present in engine exhaust fumes. CO prevents oxygen absorption by the blood, and exposure to the gas creates vision problems, headaches, disorientation, and diminished rational thinking. Refer to the FAA Civil Aerospace Medical Institute (CAMI) Aerospace Medical Education Division’s brochure titled “Carbon Monoxide: A Deadly Menace.”

2.7.5 Drugs. Similar to alcohol, illegal drugs will reduce or impair judgment and affect reflexes and hand/eye coordination. Prescription drugs and over-the-counter remedies may be dangerous when combined with flying. The FAA recommends that all pilots who take medication consult with an Aviation Medical Examiner (AME) to understand the medication’s effects on their ability to think and react while in the cockpit.

2.7.6 Ear and Sinus Pain.

2.7.6.1 Ear and sinus pain is usually caused by the eardrum or sinuses failing to equalize the air pressure during a descent. Blocked ears and sinuses can be caused by a head cold. The pain can be considerable and is most noticeable during descents. For ear blockages try yawning, swallowing, or chewing gum which may give some relief. The Valsalva procedure (pinch the nose, close the mouth, and try to force air through the nostrils) can be effective in reducing ear and sinus pain.

2.7 Objective. › 2.7.10 Stress.

2.7.6.2 If ear blockage occurs during flight, try climbing back to a higher altitude— lower air pressure—until the pain lessens. Then begin a gradual rate of descent, giving the ears and sinuses time to adapt to the increasing pressure.

2.7.6.3 After landing, nasal sprays will give some sinus pain relief. To relieve ear pain, wet paper towels with hot water and place in the bottom of two cups. Hold the cups over the ears—the warmth will help ease the inflamed tissues and reduce the pain. If pain continues, see a doctor.

Note: The best way to avoid this problem is not to fly with a head cold, upper respiratory infection, or nasal allergic condition. Be advised that some nasal and oral decongestants could be ineffective at altitude and have side effects such as drowsiness that can significantly impair pilot performance. Again, consult with an AME to understand the effects of medication before flying.

2.7.7 Fatigue. Fly only when healthy, fit, and alert. Mental and physical fatigue will generally slow down a pilot’s reaction time and affect decision making and attention span. Lack of sleep is the most common cause of fatigue, but family and business problems can create mental fatigue which can have the same effects on the pilot as lack of sleep.

2.7.8 Flicker Vertigo. Light, when flashing at a frequency between 4 to 29 cycles per second, can cause a dangerous physiological condition in some people called flicker vertigo. These conditions range from nausea and dizziness to unconsciousness or even reactions similar to an epileptic episode. When heading into the sun, a propeller cutting the light may produce this flashing effect. Avoid flicker vertigo, especially when the engine is throttled back for landing. To alleviate this when the propeller is causing the problem, frequently change engine revolutions per minute (rpm). When flying at night and the rotating beacon is creating flicker vertigo, turn it off.

2.7.9 Underwater Diving. Never fly immediately after scuba diving. Always allow 24 hours to elapse before flying as a pilot or a passenger in order to give the body sufficient time to rid itself of excessive nitrogen absorbed during diving.

2.7.10 Stress. Stress from the pressures of a job and everyday living can impair a pilot’s performance, often in subtle ways. A test pilot may further increase the stress level by setting unreasonable test flying schedules in order to meet an arbitrary “done by date.” Stress also may impair judgment, inducing the pilot to take unwarranted risks, such as flying into deteriorating weather conditions or flying when fatigued to meet a self-imposed deadline.

SECTION 6. TRANSPORTING THE AIRCRAFT TO THE AIRPORT › 2.8 Objective. Reduce damaging the aircraft in transit.

SECTION 6. TRANSPORTING THE AIRCRAFT TO THE AIRPORT

2.8 Objective. Reduce damaging the aircraft in transit.

1. Use a truck or flatbed truck/trailer large enough to carry the aircraft and the additional support equipment.

2. If the aircraft wings are removable, build padded jigs, cradles, or fixtures to hold and support them during the trip to the airport.

3. Secure the fixtures to the truck/trailer, and then secure the wings to the fixture.

4. Use two or more ropes at each tiedown point.

5. Use heavy moving pads used for household moves to protect the wings and fuselage. Most rent-a-truck firms offer them for rental.

6. During the planning stage, obtain applicable permits and follow the local ordinances for transporting an oversized load. Ask the local police if they can provide an escort to the airport.

7. Brief the moving crew thoroughly before loading and unloading the aircraft.

8. Ensure the designated driver has recent experience driving a truck/trailer and is familiar with the roads to the airport.

SECTION 7. ASSEMBLY AND AIRWORTHINESS INSPECTION › 2.11 Fitness Inspection—Airframe.

SECTION 7. ASSEMBLY AND AIRWORTHINESS INSPECTION

2.9 Objective. To determine the airworthiness of the aircraft and its systems.

2.10 General.

2.10.1 If you have to reassemble the aircraft after moving it to the airport, take time to do so carefully. This is a critical event because mistakes can easily occur due to the builder’s preoccupation with the impending first flight of the aircraft. One of the most common and deadly mistakes is to reverse the rigging on the ailerons. To prevent errors in reassembling the aircraft, follow the designer’s or kit manufacturer’s instructions, or use a written checklist specifically designed as part of the flight test plan. At the completion of each major operation, have another expert check the work.

2.10.2 After reassembling the aircraft, perform a preflight “fitness inspection.” This inspection should be similar to an annual inspection. You should perform the fitness inspection even if the FAA has just issued a Special Airworthiness Certificate for the aircraft. Even if a builder was 99 percent perfect and performed 10,000 tasks building the aircraft, there would still be a hundred items that would need to be found and corrected before the first flight. Professional industry technical advisors or counselors are available to inspect the aircraft following reassembly.

2.11 Fitness Inspection—Airframe. A builder-developed comprehensive post-assembly checklist should be used, and the results of that inspection should be recorded on the checklist to provide increased assurance that all items of concern have been addressed and the results documented. The following additional safety checklist items may not be

2.11.5 Control Surfaces. › 2.11.5.2 While checking cable tension, make sure there is no “free…

applicable to all amateur-built make and model aircraft, but the FAA presents them here for consideration and review.

2.11.1 Control Stick/Wheel. The control stick/wheel should have a free and smooth operation throughout its full range of travel. There should be no binding or contact with the sides of the fuselage, seat, or instrument panel. There should be no free play (slack) in the controls, nor should the controls be tight as to have stick-slip movement.

2.11.2 Rudder Pedals. Move the rudder pedals through the full range of travel. The pedal movement should be smooth, and without any binding. The test pilot’s shoes should not catch on exposed metal lines, fixtures, or electrical wire harnesses.

2.11.3 Brakes. Hand and/or toe brake pressure should be firm with no tendency to bleed down or lock up. Spongy brakes that are “pumped up,” or that show a drop in the brake fluid reservoir level after a few brake applications, indicate a brake fluid or air leak in the system.

2.11.4 Main Landing Gear. Ensure that the gear attach points, shimmy damper, bungees, wheels, brakes, and wheel fairings are airworthy. If applicable, check that the tailwheel pivot point is centered and vertical compared to the longitudinal axis of the aircraft. It is critical that the main landing gear alignment toe in/toe out is zero or matches the specifications for fuselage/landing gear alignment called out in the plans. Even one landing gear wheel out of alignment can cause a ground loop.

2.11.5 Control Surfaces. Perform rigging checks to ensure that control input for ailerons, rudder, elevators, and trim tabs results in the correct amount of travel and direction of the control movement and that these control surfaces make contact with their stops. Also, ensure that the flaps, if installed, have the proper travel, operate as a single unit, and cannot be extended beyond the maximum extended position. It is important to ensure that the control cable tension is correct by (1) checking it with a calibrated tensiometer; and (2) confirming that all the attachment hardware is secured and turnbuckles are properly safetied.

2.11.5.1 If the cable tension is less than required by specifications, in-flight air loads will prevent full travel of the control, even if the control has the right amount of deflection and hits all the stops in the cockpit/wing/tail when tested on the ground. With low cable tension, the slack in the cables will absorb the desired control movement input.

2.11.5.2 While checking cable tension, make sure there is no “free play” in the flight control hinges and rod ends. Free play and loose cable tension combined with control mass imbalance can bring on control surface “flutter.” Do not, however, rig the controls at too high a cable tension. This will cause a high wear rate on the pulleys and prevent good control feel, especially at low airspeeds.

SECTION 7. ASSEMBLY AND AIRWORTHINESS INSPECTION › 2.12 Field Check.

2.11.6 Instrument Panel.

2.11.6.1 All the instruments should be properly secured in the panel and have preliminary markings on them. The airspeed indicator and engine tachometer should be marked with the expected performance range markings. The engine manufacturer’s recommended operating range for oil temperature and oil pressure should be marked on engine instruments. If the markings are on the instrument glass face, paint a white slippage mark on both the glass and on the instrument case to alert the pilot in case the glass/range marks have moved. Attach a temporary placard to the instrument panel with the expected stall, climb, and glide speeds. It is a handy reference in times of emergency.

2.11.6.2 Angle of attack (AOA) systems may require in-flight calibration. Information displayed prior to that calibration may not be accurate.

2.11.6.3 Electronic data collection systems, when installed, should be checked if possible before flight according to the manufacturer’s instructions. Recording of electronic data through flight and engine instruments can be very useful, but only if it is ensured that accurate information is being collected. Therefore, verification of this data prior to flight is important. It is recommended to carefully and properly configure and calibrate electronic flight instrument systems (EFIS) using manufacturer guidance.

2.11.7 Behind the Instrument Panel. Very few amateur-built aircraft of the same make and model have the same instrument panel design. Amateur builders should inspect this area to ensure that all line connections are tight, that nothing interferes with control travel, and there are no loose wires or fuel, oil, or hydraulic leaks.

2.11.8 Carbon Monoxide (CO). CO leak checks also can be performed. Wait until night or put the aircraft in a dark hangar. Climb into the cockpit and have a friend shine a bright flood light close to the firewall. If light leaks into the cockpit, CO can seep in. Mark it and seal it.

2.11.9 Engine and Propeller Controls. All controls should be visually inspected, move in the proper direction, and be securely mounted. The friction lock on both controls should be checked for operation. Each control should have full movement with at least a ¼ inch “cushion” at the full travel position. The control cables should be firmly attached to the fuselage along each 24 inches of their runs to prevent whipping of the cable and loss of cable movement at the other end. Control cables with ball sockets should have large area washers on either end of the bolt connection. This will ensure the control will remain connected, even if the ball socket fails and drops out.

2.11.10 Altimeter System. The best procedure to check the altimeter for leaks and accuracy is to have the entire altimeter system checked in accordance with 14 CFR part 43 appendix E, at an FAA-approved repair station.

2.12 Field Check. You need two people to accomplish the following field check by which an amateur builder can detect if the aircraft’s pilot-static instrument system is leaking:

2.12 Field Check. › 2.12.3 Fuel System.

Note: This field check is not an accuracy check. Additionally, you should check the manufacturer’s manuals for the installed pitot-static instruments to ensure that this test method will not damage any associated electronics.

2.12.1 Airspeed Check. Slip a long rubber hose over the pitot mast (the FAA recommends surgical tubing). As one person reads the airspeed, the other should very slowly roll up the other end of the tubing. This will apply pressure to the instrument. When the airspeed indicator needle reaches the aircraft’s approximate recommended cruise speed, pinch the hose shut, and hold that reading. The airspeed needle should remain steady for a minute if the system is sound. A fast drop off will indicate a leak in the instrument, fittings, lines, or the test hose attachment. Never force air into the pitot tube or orally apply suction on a static vent—this action will damage the instruments.

2.12.2 Altimeter/Vertical Speed Check.

2.12.2.1 To check the static side, apply low suction at the end of the static vent port. The easiest way to gain access to the static system is to remove the static line at the static port. If there are two static ports, tape the unused port closed. Next, get 2 feet of surgical tubing, seal one end, and tightly roll it up. Attach the open end to the static line and slowly unroll the tubing. This will apply a suction, or low pressure, to the static system.

2.12.2.2 The altimeter should start to show an increase in altitude. The vertical speed indicator also should indicate a rate of climb. The airspeed may show a small positive indication. When the altimeter reads about 2,000 feet, stop and pinch off the tube. There will be some initial decrease in altitude and the vertical speed will read zero. The altimeter should then hold the indicated altitude for at least a minute. If altitude is lost, check for leaks.

Note: The above airspeed and altimeter field checks are a check of the system for possible leaks, and are not the same as airspeed or static system accuracy tests done by a certificated repair station. The checks do not include the pitot tube and static ports located on the airframe. The FAA recommends the builder not deviate from the designer’s original plans when installing the pitot and static system.

2.12.3 Fuel System. According to NTSB Safety Study SS-12-01, The Safety of Experimental Amateur-Built Aircraft, the 2001–2010 accident cases included examples involving loss of engine power during the first few hours of operation of a newly built aircraft. Some of the fuel system design and installation problems found in these cases include incorrectly installed fuel lines, crimped vent lines, system leaks, and a fuel system that did not provide adequate fuel pressure to maintain engine power. The NTSB concluded that a functional test of the aircraft fuel system could identify design deficiencies, leaks, and malfunctions prior to flight that would prevent fuel system- and powerplant-related accidents early in the operational life of an aircraft.

2.12 Field Check. › 2.12.6 Avionics and Electrical Checks.

2.12.3.1 Before filling the aircraft’s fuel tanks, the amateur builder should vacuum any manufacturing debris from each tank and wipe them down with a “tack” cloth (available from a paint supply store). Next, the builder should flush the system with aviation grade gasoline several times in order to remove any small or hard to reach debris from the tanks and lines. The builder should also clean the fuel filter/gascolator screen/carburetor finger screen. The amount of time spent “sanitizing” the fuel system will provide big safety benefits for the life of the aircraft.

2.12.3.2 When filling the tanks, place the aircraft in the straight and level cruise position. Add fuel in measured amounts to calibrate the fuel tank indicators. While allowing the aircraft to sit for a short time to observe for possible leaks, inspect the fuel tank vents to see if they are open and clear. Check that the fuel tank caps seal properly. If there are no leaks and the fuel system has an electric boost pump, pressurize the system and again check for leaks. The fuel selector, vents, and fuel drains should be properly marked and tested for proper operation.

Note: Many amateur-built aircraft take 5 to 8 years to build. During that time, many rubber-based oil and fuel lines and cork gaskets installed early in the building process may have age hardened, cracked, and/or turned brittle. The builder should carefully inspect these components and replace as necessary to prevent a premature engine failure.

2.12.4 Retractable Landing Gear System. If equipped with a retractable landing gear system, whether hydraulic, electrical, or mechanical, the system should function dependably and positively in accordance with the designer’s intent. The builder/pilot should rigorously cycle the retractable landing gear in the appropriate ground setup, using both the normal and emergency landing gear extension system. There should be no hang-ups or binding. If equipped, a function check of the weight on wheel switch and onboard landing gear indicators should also be performed.

2.12.5 Safety Belt and Shoulder Harness. You should check these items for condition and proper installation. A review of amateur-built aircraft accidents has disclosed a significant number of accidents in which the seatbelt mounting hard points failed. You should check each seatbelt and shoulder harness mounting hard point to the designer’s specifications so it will hold the harness and pilot in the aircraft at the ultimate design “G” load specification, both positive and negative, for the aircraft.

2.12.6 Avionics and Electrical Checks. Test the avionics systems. Perform an operational check to ensure the radio(s) transmit and receive on all frequencies. Inspect circuit breakers/fuses, microphones, and antennas for security and operation. Test the emergency locator transmitter for proper operation and battery life. Check electrical systems for operation of lights, instruments, and basic navigation/communication performance. You can check other electrical systems, such as generator/alternator output, during engine run-ins, taxi, and flight tests. Check the battery and the battery compartment for security

2.13 Objective. › 2.13.2 Method.

and if applicable, proper venting to the outside of the aircraft. Check the condition of the engine-to-airframe bonding (grounding) wire. Ensure that all electrical instruments operate properly.

2.12.7 Cowling and Panel Checks. Ensure that all inspection panels are in place, the cowling is secured, and cowl flap operation is satisfactory. Inspect the propeller spinner and its backing plate for cracks.

2.12.8 Canopy/Door Locks Checks. Ensure the canopy or doors on the aircraft work as intended. Double check the canopy or door lock(s) so the canopy and doors will not open in flight and disturb the airflow over the wings and stall the aircraft. If a canopy jettison system is installed, check for proper operation when the aircraft on the ground and when it is on jacks. (Jacks will simulate flight loads on the aircraft.)

SECTION 8. WEIGHT AND BALANCE

2.13 Objective. Discuss the importance of developing accurate W&B calculations for both test and recreational flights. You can find additional information on W&B in FAA-H-8083-1, Aircraft Weight and Balance Handbook.

2.13.1 Accuracy. A good W&B calculation is the keystone of flight testing. Accurately determining the aircraft’s takeoff weight and ensuring that the CG is within the aircraft’s design for each flight is critical to conducting a safe flight test.

2.13.2 Method. An aircraft should be in a level flight position, spanwise and fore and aft, in accordance with the manufacturer’s instructions, when weighed. The FAA highly recommends you weigh the aircraft in an enclosed area, using three calibrated scales. The

2.13.3 A Word about Lateral Balance. › 2.13.3.3 Caution should be exercised before undertaking any…

FAA does not recommend bathroom scales because they are not always accurate. Ensure all fuel tanks are empty.

2.13.3 A Word about Lateral Balance. Aircraft lateral balance (side to side) is often overlooked, because in most situations loading an aircraft is a matter of loading ballast in the form of cargo or people inside the aircraft very close to its centerline. The effects on lateral unbalance from a difference in ballast weight inside the aircraft are usually minimal.

2.13.3.1 Aircraft that have fuel in the wings usually have one or more fuel tanks located symmetrically from one wing to the other so lateral balance is not affected. The lateral CG may become important if the fuel load is mismanaged by supplying the engine(s) unevenly from tanks on one side of the aircraft. Care should be taken when fueling the aircraft evenly so lateral balance is not affected on takeoff unexpectedly. Mismanagement of fuel or uneven fuel loading on aircraft with tip tanks or modified (enlarged or repositioned) fuel tanks can affect aircraft controllability in all phases of flight.

2.13.3.2 An airplane is designed so that the primary flight controls (rudder, aileron, and elevator) are streamlined with the non-movable airplane surfaces when the airplane is in a cruising straight-and-level at normal weight and loading configuration. If the airplane is flying out of that basic balanced condition, one or more of the control surfaces is going to have to be held out of its streamlined position by continuous control input. An improperly balanced airplane requires constant control pressures, produces pilot tension and fatigue, distracts the pilot from scanning, and contributes to abrupt and erratic airplane attitude control. The use of inflight adjustable trim tabs and/or autopilot systems can relieve pilot fatigue but can also mask a potential catastrophic controllability problem until it is too late to take corrective action.

2.13.3.3 Caution should be exercised before undertaking any modification to the aircraft fuel system. Along with fuel flow testing and determining proper fuel line routing, changes in performance in flight maneuvers from changes in the aircraft lateral balance need to be addressed. Phase I flight testing needs to be conducted for any modification that can change the lateral balance of the aircraft.

2.14.2 To Work a CG Problem. › 2.14.2.4 Multiply the inches (arm) by the weight on each wheel to get…

Figure 2-5. Empty Weight CG

ITEMS WEIGHT

(LBS)

ARM (INCHES) MOMENT (IN-LBS)

Left Wheel 101 60 6060

Right Wheel 99 60 5940

Nose/Tailwheel 42 180 7560

TOTALS 242 80.8 19560

𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀

𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊= 𝐸𝐸𝐸𝐸𝐸𝐸𝐸𝐸𝐸𝐸 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊 𝐶𝐶𝐶𝐶

OR

19560 242 = 80.83

2.14 Determining Empty Weight CG.

2.14.1 Sample Aircraft. The sample airplane for determining empty weight is a single seat aircraft, with a design empty weight of 242 pounds and a gross weight limit of 500 pounds. The datum line is located at the nose of the aircraft and the CG range is between 69 to 74 inches from the datum.

2.14.2 To Work a CG Problem. Figure the empty weight CG first. On a piece of paper, draw four blocks. Title each block from left to right as shown in Figure 2-5.

2.14.2.1 Under the block titled “Items,” vertically list “left wheel,” “right wheel,” “nose/tailwheel,” and “TOTALS.”

2.14.2.2 Place a calibrated scale under each wheel and record the weight on each gear, in pounds, in the weight block beside the appropriate wheel.

2.14.2.3 Measure the distance in inches from the datum line, or imaginary point identified by the manufacturer (e.g., nose of the aircraft), to the centerline (C/L) of the three wheels. Record the distance of each wheel and place it in the “arm” block beside the appropriate wheel. See Figure 2-5.

2.14.2.4 Multiply the inches (arm) by the weight on each wheel to get the moment (inch-pounds) for each wheel. Add the weight on the three gears and the three moments in inch-pounds and divide the total weight into the total moment. The sum is the “empty weight center of gravity” in inches. In the sample case, the empty weight CG is 80.83.

Note: All calculations should be carried out to two decimal places.

SECTION 8. WEIGHT AND BALANCE › 2.15 Determining Takeoff Weight CG.

Figure 2-6. Takeoff CG

ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)

A/C 242 80.8 19554

Pilot 170 65 11050

Fuel 30 67 2010

TOTALS 442 73.8 32614

𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀

𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊= 𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝐶𝐶𝐶𝐶

OR

32614 442 = 73.8

2.15 Determining Takeoff Weight CG.

1. Since the aircraft’s empty weight and empty weight CG are fixed numbers, the only way an aircraft’s CG can be changed is by adding weight in other locations.

2. For example, in Figure 2-6, the aircraft’s empty weight has been written in the appropriate blocks. The pilot weighs 170 pounds and fuel—5 gallons—weighs 30 pounds.

3. Again, all measurements are made from the datum to the centerline of the object that has been added. Weight multiplied by inches from the datum equals moment. Add the weights and moments to find the takeoff CG for that particular flight.

4. Loaded in this configuration, the aircraft has an aft CG, but is still within the CG flight envelope and is safe to fly. The pilot must consider the effect an aft CG will have on the flight characteristics of the aircraft.

2.16 Additional Equipment Testing. › 2.16.6 If the sample aircraft exceeded the designer’s gross weight…

Figure 2-7. Additional Equipment Added

ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)

A/C 242 80.8 19554

Pilot 170 65 11050

Fuel 30 67 2010

S/B 15 75 1125

Strobe 1.5 179 268.5

Fuel 1.5 55 82.5

TOTALS 460 74.1 34090

𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀

𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊= 𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴 𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊ℎ𝑡𝑡 𝐶𝐶𝐶𝐶

OR

34090 460 = 74.1

2.16 Additional Equipment Testing.

2.16.1 During flight testing, a strobe battery and handheld radio are added. The battery/battery box weight is 15 pounds and the location is 75 inches aft of the datum. The strobe assembly weight is 1.5 pounds and is located 179 inches aft of the datum. The radio’s weight is 1.5 pounds and is located 55 inches aft of the datum. See Figure 2-7.

2.16.2 In the sample problem, the previous figures for takeoff weight and moment are still accurate, hence those numbers have been listed in the appropriate blocks.

2.16.3 Add the battery, strobe, and radio data in the appropriate locations and calculate the totals. At 465 pounds, the aircraft is still 35 pounds under its design gross weight limit of 500 pounds but is out of balance because the CG has moved 0.3 inches further aft (74.1 inches) and exceeds the allowable rear CG limit of 74 inches.

2.16.4 Since the aircraft is out of balance with an aft CG, it is no longer stable in pitch and would be dangerous to fly. In most cases, it is not the amount of weight added to the aircraft that can cause a major safety problem but its location.

2.16.5 To bring this aircraft back into the safe CG range, the battery would have to be moved 4 inches forward or 71 inches from the datum line. Another alternative is to install 8 pounds of ballast in the nose, 20 inches from the datum.

2.16.6 If the sample aircraft exceeded the designer’s gross weight limit, such as with a 300-pound pilot instead of the CG limit, its climb, stall, and performance capability would be poor and the possibility for in-flight structural failure would be high.

2.17 Objective. › 2.17.2 Airworthiness/Registration/Operating Limitations/Placards/W&B.

Note: In the sample W&B, positive numbers were chosen by placing the datum line on the nose of the aircraft. Some manufacturers prefer to use a datum located somewhere between the aircraft’s nose and the leading edge of the wing.

2.16.7 This kind of datum will set up a system of positive arms, or items located aft of the datum, and negative arms—items located forward of the datum.

2.16.8 When working a W&B problem with negative and positive moments, subtract the sum of all negative moments from the sum of all positive moments to reach a “total moment” for the aircraft.

SECTION 9. PAPERWORK

2.17 Objective. Have the proper documentation and paperwork to conduct the flight test.

2.17.1 Weight and Balance (W&B). The W&B for the aircraft should be carefully done. The gross weight and CG range should be determined prior to every flight. An equipment list should be developed and maintained to identify the appliances and articles installed in the aircraft at the time of weighing for certification. It should also be kept current as installed equipment changes from additions or removals.

2.17.2 Airworthiness/Registration/Operating Limitations/Placards/W&B. The aircraft is not considered to be in a condition for safe operation if these documents are not on board.

2.17.3 Checklists. In addition to the assembly/airworthiness inspection previously discussed in Chapter 2, Section 7, the builder should prepare the following checklists:

2.17 Objective. › 2.17.5 Maintenance Records (Logbooks).

1. Preflight;

2. Before starting;

3. Starting the engine;

4. Before takeoff;

5. Takeoff/cruise;

6. Descent/before landing;

7. After landing;

8. Securing the aircraft; and

9. Emergency procedures.

Note 1: A checklist to cover the above procedures may seem a tedious task, but it may only be the size of a 5x8 card similar to a checklist for a Cessna 150 or a Piper Cherokee.

Note 2: The amateur builder should anticipate several revisions to the checklist.

2.17.4 Flight Manual. It is imperative that a flight manual describing the anticipated performance of the aircraft be written by the aircraft builder/kit manufacturer. The manual will be revised several times during the flight test phase until it accurately reports the aircraft’s performance, as well as limitations, normal and emergency procedures, and descriptions of those systems installed. Amateur builders should follow community and/or kit manufacturer recommendations for flight manual formatting and content.

2.17.5 Maintenance Records (Logbooks). Operators of amateur-built aircraft are required to maintain a record of the annual condition inspection in accordance with their operating limitations. The FAA recommends that owners record all maintenance (to include inspections) performed in the aircraft’s logbooks. This will create a history of the aircraft’s maintenance and will be invaluable in spotting trends.

2.18.2 New/Newly Overhauled Engine Run-In Procedures. › 2.18.2.1 Most amateur builders start with a new or newly overhauled…

SECTION 10. POWERPLANT TESTS

2.18 Objective. Ensure that the engine has been properly run-in and is safe to operate in all rpm ranges.

2.18.1 Testing. You can conduct an engine pre-oil and cold compression test as follows:

1. Remove the rocker-box covers and one spark plug from each cylinder.

2. Using an external oil pump, or by rotating the propeller in the direction of rotation, pump a substantial supply of oil up from the sump into the rocker arms.

3. When the engine is pre-oiled, run a cold compression test of each cylinder.

4. The results will serve only as an initial benchmark for comparing other compression tests taken after the engine has been run-up to operating temperature.

2.18.2 New/Newly Overhauled Engine Run-In Procedures.

2.18.2.1 Most amateur builders start with a new or newly overhauled engine and proceed to “run it in” on the airframe. This practice is followed because builders usually don’t have either a test cell or a special “club” propeller that is specifically designed to aid in engine cooling during run-in. There are pros and cons to using an airframe to run in an engine, but the best advice has always been to follow the engine manufacturer’s instructions, found either in the manufacturer’s overhaul manuals, service bulletins, or service letters. Following the manufacturer’s instructions is especially important if the engine has chrome cylinders which require special run-in procedures.

2.18.5 Test and Support Equipment. › 2.18.5.4 If there is only one CHT thermocouple, attach it to the…

2.18.2.2 Also, before running-up the engine, be certain that it has the proper grade oil in the sump. Some new and newly overhauled engines are shipped with a special preservative oil to prevent corrosion. Drain this out and service the engine with the correct oil before starting.

2.18.3 Used Engine Run-In Procedures. Some amateur builders install a used engine from a flyable aircraft. The same checks and adjustments as are performed on a new or newly overhauled engine should be conducted on a used engine.

Note: Both new and used engines require special attention to engine cylinder baffling to ensure cylinder cooling is within the engine manufacturer’s Cylinder Head Temperature (CHT) specifications.

2.18.4 Pre-Run-In Checks.

2.18.4.1 Before beginning the powerplant tests, inspect the engine and propeller carefully. All fuel and oil line connections should be tight. Check the torque on the engine mount attaching bolts. Be certain that there are no tools, hardware, or rags lying between the cylinders or under the magnetos.

2.18.4.2 Check for the proper amount of oil in the engine and that the dipstick gives an accurate reading of the oil quantity. Be advised that some engines are mounted on an angle in TC’d aircraft. These engines have a special oil dipstick, which corrects for the different angle of oil in the crankcase. The same engine, mounted level in an amateur-built aircraft with the original dipstick, will not show the correct oil quantity.

2.18.5 Test and Support Equipment.

2.18.5.1 A CHT gauge is needed to ensure that all cylinders are receiving the proper flow of cooling air.

2.18.5.2 On the newer aircraft engines, the cylinders are drilled and tapped to accept a bayonet-type CHT thermocouple probes. For older engines, the thermocouple is designed like a spark plug washer and fits under a spark plug. It can be installed in any cylinder, under either the top or bottom spark plug.

2.18.5.3 CHT monitors can have multiple thermocouples which may be connected to a selector switch in the cockpit, which the pilot uses to select a cylinder to monitor. This also is an excellent troubleshooting tool for identifying fouled plugs and bad ignition leads.

2.18.5.4 If there is only one CHT thermocouple, attach it to the rearmost cylinder on the right side of the engine, as viewed from the cockpit, and run up the engine. Run the same test on the opposite rearmost cylinder to be certain the hottest running cylinder is monitored. You also need calibrated oil pressure and oil temperature gauges to test the accuracy of the engine instruments installed in the aircraft.

2.18 Objective. › 2.18.6 Safety Precautions.

2.18.5.5 Exhaust gas temperature (EGT) thermocouple probes, commonly known as EGTs, are becoming popular in amateur-built experimental aircraft. EGTs help monitor the engine and can be an excellent way of determining which spark plug/plug wire requires attention during a magneto check and provides information on the health of the valves and cylinders. Just like CHTs, there can be one for the entire engine or one for each cylinder exhaust pipe. EGT manufacturer installation instructions and cautions should be closely followed. Accurate readings for EGTs are greatly affected by placement on the exhaust and the relation to airflow around the engine.

2.18.5.6 The following support equipment is recommended to be carried on board the aircraft (not all-inclusive):

• Fifty feet or more of tiedown rope,

• Tiedown stakes,

• Two chocks for each wheel,

• Fire extinguisher,

• Assorted hand tools,

• Safety-wire,

• Cotter-pins,

• Ear and eye protection,

• Grease pencils,

• Logbooks,

• Clip board,

• Pen and paper,

• A watch to time the tests,

• Rags, and

• Manufacturer’s instructions.

2.18.6 Safety Precautions. Before the first engine run, ensure the aircraft is tied down, brakes on, and the wheels are chocked. The builder and flight test team should wear ear and eye protection. All flight test participants should be checked out on fire extinguisher use and operation. During engine runs, do not allow anyone to stand beside the engine, or inline or close to the propeller. Making minor adjustments to a running engine, such as idle and mixture settings, is a very dangerous procedure and should be done with great care by experienced individuals.

2.18 Objective. › 2.18.8 Engine Cooldown.

2.18.7 The First Engine Run.

2.18.7.1 The first start of the engine is always a critical operation. The engine should be pre-oiled using the manufacturer’s instructions. For aircraft using other than FAA-approved oil pressure and temperature gauges, the FAA recommends attaching an external calibrated oil temperature and pressure gauge to calibrate the engine instruments. After priming the engine and completing the starting engine checklist items, the first concern is to get an oil pressure reading within the first 20 to 30 seconds after engine start. If there is no oil pressure reading, shut down the engine.

2.18.7.2 There are three common problems that would cause low or fluctuating oil pressure.

1. Air in the oil pressure gauge line. This is easily fixed by loosening the line connection near the oil pressure gauge and squirting oil into the line until full. Another option is to use a pre-oiler to provide the pressure and carefully bleed the air out of the line near the oil gauge by loosening the B-nut connecting the oil line to the gauge.

2. A misadjusted oil pressure relief valve. Cleaning the pressure relief ball, checking for the proper number of washers, correcting spring tension, and re-adjusting the setting could solve the problem.

3. An internal problem within the engine, most likely the oil pump. An engine tear down would be required.

2.18.7.3 With good oil pressure/temperature readings and the engine running smoothly, ensure that the engine oil pressure and temperature gauges in the cockpit match the calibrated oil pressure and temperature gauges attached to the aircraft for the first run. Do not overlook this test. It is critical to determine the accuracy of the cockpit engine gauges not only for the ground engine run-in period, but also for in-flight engine cooling tests.

2.18.7.4 Work through the engine manufacturer’s run-in schedule. Most engine manufacturers recommend a series of engine runs from low rpm to maximum rpm. Each run usually incorporates a 200-rpm increase and lasts no longer than 10 minutes. The secret to a successful engine run is not to let the engine temperatures exceed manufacturer’s limits during engine runs.

Note: Engines with chrome cylinders or chrome rings require different high power run-in programs. Follow the manufacturer’s run-in instructions to ensure the engine will perform satisfactorily over its lifetime.

2.18.8 Engine Cooldown. After a ground run, the cooling off period takes approximately an hour. This is because a newly overhauled engine needs time for the internal parts, such as rings, cylinders, valves, bearings, and gear faces, to expand and contract several times to obtain a smooth surface that retains its “memory.” This is a lengthy process even when done right, but it is important not to skip any of the recommended runs. You risk

2.18.11 After Shut-Down. › 2.18.11.3 The FAA also recommends all fuel sumps, filters, and…

increasing oil consumption and reducing overall engine performance, reliability, and engine life span—which could be costly in the long-term—if you skip any of the runs.

2.18.9 Record the Engine Run-In Data. During the engine run, monitor the CHTs, oil temperature, and oil pressure. Record the readings and adjustments for future reference. If the CHTs are rising close to the red line, reduce power and stop the test. Some causes of high CHTs include:

• Using spark plugs with the improper heat range;

• CHT gauges installed on the wrong cylinder;

• Missing or badly designed cylinder head cooling baffles;

• Partially plugged fuel nozzles (applicable to fuel injected engines);

• Fuel lines of improper internal diameter (creates lean mixtures);

• Engine improperly timed either mechanically and/or electrically; and

• The carburetor fuel mixture set excessively lean.

2.18.10 Selecting Adjustments. Narrow down what adjustments need to be made by recording the change and its resulting effects. The record of the change and its effects are then used for making a logical decision for follow-on adjustments as needed to reach the proper engine performance parameters. Two ways of recording the engine performance parameters are:

2.18.10.1 Keeping a detailed paper log of each applicable engine instrument on each run-up.

2.18.10.2 Using an EFIS to record all engine performance indications for all engine runs in their entirety. EFIS for experimental aircraft may consist of either a standalone system or be connected to a multifunction display (MFD).

2.18.11 After Shut-Down.

2.18.11.1 After each engine run, check for fuel and oil leaks, loose connections, and hot spots on cylinders, which can be indicated by burnt paint. The FAA recommends draining the oil and removing the oil screen/filter within the first 2 hours of running the engine. Check the screen/filter for ferrous metal with a magnet. Wash and inspect the screen/filter for non-ferrous metal like brass, bronze, or aluminum.

2.18.11.2 A very small quantity of metal in the screen is not uncommon in a new or newly overhauled engine. It is part of the painful process of “running-in.” If subsequent oil screen checks—2 hours apart—show the engine is “making metal,” this indicates a problem inside the engine and a tear down inspection is required.

2.18.11.3 The FAA also recommends all fuel sumps, filters, and gascolators should be checked for debris after each engine run. Special attention should be given to

2.19.1 Mixture and Idle Speed Check. › 2.19.1.4 Just before the engine quits, the engine rpm should rise about…

the fuel system by builders who use composite or fiberglass fuel tanks. Composite and fiberglass strands can be very fine, making visual detection difficult. Frequent cleaning of the fuel filters and screens early in the flight testing phase will avoid a gradual buildup of loose composite fibers, which would reduce or stop the flow of fuel to the engine.

SECTION 11. ADDITIONAL ENGINE TESTS

2.19 Objective. All of the engine and fuel system tests and inspections should be listed and recorded on a checklist designed for that purpose. That document should note the completion of each of the above tests with information obtained during that test. Record the fuel flow, compression test, magneto timing, idle speed, oil pressure, hot and cold, etc. These checks will determine if the engine supply of fuel is adequate at all angles of attack.

2.19.1 Mixture and Idle Speed Check. After completing the initial engine “run-in” tests, check the idle speed and mixture settings. To determine if the mixture setting is correct, perform the following:

2.19.1.1 Warm up the engine until all readings are normal.

2.19.1.2 Adjust the engine rpm to the recommended idle rpm.

2.19.1.3 Slowly pull the mixture control back to idle cut-off.

2.19.1.4 Just before the engine quits, the engine rpm should rise about 50 rpm if the mixture is properly adjusted. If the rpm drops off without any increase in rpm,

2.19.3 Cold Cylinder Check. › 2.19.3.1 The builder should perform a cold cylinder check if the engine…

the idle mixture is set too lean. If the rpm increases more than 50 rpm, the idle mixture is set too rich.

2.19.1.5 Because most air-cooled aircraft engines need excessively rich fuel air mixtures to provide cooling for full-throttle operation, the condition should be confirmed. This is most easily accomplished by running the engine at full throttle (with the aircraft properly secured), manually leaning the mixture, and observing an increase in EGTs and in some cases an actual rise in rpm. While the amount of EGT rise is variable, the important aspect is that there is a rise of 25 to 50 degrees Fahrenheit (°F) or more. This will help alleviate engine overheating situations during the first few hours of inflight operation.

Note: Some amateur builders, after properly setting the idle mixture/rpm to the manufacturer’s specification, increase the engine idle rpm by 100 rpm for the first 10-plus hours of flight testing. This is to ensure that the engine will not quit when the throttle is pulled back too rapidly, or when power is reduced on the final approach to landing. Be aware that in some situations, particularly with light wing loading or low drag types of aircraft, adding 100 rpm to the idle speed could cause the landing distance to be increased significantly and also have an unexpected adverse effect on landing behavior.

2.19.2 Magneto Check.

2.19.2.1 The magneto checks should be smooth and the difference between both magnetos rpm drops should average about 50 rpm. The builder also should perform a “hot mag” check, to prevent unexpected engine self-starts. To perform this check, run up the aircraft until the engine is warm. At idle rpm, turn the magneto switch off, the engine should stop running. If the engine continues to run, one or both of the magnetos is not grounded, or “hot.”

2.19.2.2 The usual causes for a hot magneto are a broken “P” lead coming out of the magneto or a bad magneto switch. THIS IS AN IMMEDIATE THREAT TO THE PERSONAL SAFETY OF ANYONE NEAR THE AIRPLANE AND SHOULD BE REPAIRED AT ONCE.

2.19.3 Cold Cylinder Check.

2.19.3.1 The builder should perform a cold cylinder check if the engine is running rough and an ignition system problem could be contributing. A cold cylinder can be detected easily by switching magnetos and reading modern EGT monitors (if equipped) or by aiming a handheld laser thermometer at each exhaust stack. If you have neither one, perform the following:

1. Run the engine on the bad magneto for about 30 seconds at 1,200 rpm. Without switching the mag switch back to “both,” shut off the engine.

2.19.5 Fuel Flow. › 2.19.5.1 Place the aircraft’s nose at an angle 5 degrees above the…

2. One of the test crew should quickly use a grease pencil to mark an area of the exhaust stacks approximately an inch from the flange that attaches the stacks to the cylinders.

3. Check the marks on the stacks. If one or more of the exhaust stacks with a grease mark has NOT been burned to a grayish-white color and the mark on the stack still retains most of the original color of the grease pencil, the “cold cylinder” has been identified.

2.19.3.2 Probable causes of the cold cylinder problem are: (1) defective spark plugs, (2) ignition leads, or (3) a cracked distributor in one of the magnetos. To detect if the spark plugs are bad, switch both plugs to another cylinder. If the grease pencil proves the problem moved to the new cylinder, the spark plugs are bad. If the problem remains with the original cylinder, the ignition lead or magneto is bad.

2.19.4 Carburetor Heat.

2.19.4.1 The FAA strongly recommends that all amateur builders using a carbureted engine install a carburetor heat, or “carb heat,” system that complies with the engine manufacturer’s recommendation. If no recommendation is available, we suggest a carb heat system for a sea-level engine. A conventional venturi should be designed so that it will provide a 90 °F increase in the venturi at 75 percent power. For altitude engines using a conventional venturi carburetor, 120 °F increase in venturi temperature at 75 percent power will prevent or eliminate icing. Remember: Too little carb heat will have no effect on carburetor icing, and too much carb heat will cause an overly rich mixture which will reduce power and may shut down the engine.

2.19.4.2 During the engine tests, make numerous checks of the carb heat system. To avoid overly rich mixtures from oversized carb heat ducts, ensure that the carb heat duct is the same size as the inlet of the carburetor.

2.19.4.3 Be certain there is a positive reduction in rpm each time “carb heat” is applied. If there is no reduction, or the rpm drop is less than expected, check the carb heat control in the cockpit and on the carb heat air box for full travel. Also, check for air leaks in the “scat tube” connecting the heat muff to the carburetor air box.

2.19.5 Fuel Flow. A fuel flow and unusable fuel check is a field test to ensure the aircraft engine will get enough fuel to run properly, even if the aircraft is in a steep climb or stall attitude, and is accomplished in the following manner:

2.19.5.1 Place the aircraft’s nose at an angle 5 degrees above the highest anticipated climb angle. The easiest and safest way to do this with a conventional gear aircraft is to dig a hole and place the aircraft’s tail in it. For a nose gear aircraft, build a ramp to raise the nose gear to the proper angle.

Continue reading ↓ 120 of 309 passages shown