AC 90-89B Amateur-Built Aircraft and Ultralight Flight Testing Handbook
This advisory circular (AC) provides suggestions and safety related recommendations primarily to assist amateur and ultralight builders in developing individualized aircraft flight-test plans. It also provides guidance for experimental light sport aircraft flight testing after modifications to the aircraft. It provides recommendations and suggestions you can combine with other sources on test flying, such as the aircraft plan/kit manufacturer’s flight testing instructions and other flight testing data. This will help you develop a detailed flight-test plan, tailored for your aircraft and resources. This AC attempts to make you aware that test flying an aircraft is a critical undertaking, which you should approach with thorough planning, skill, and common sense. The flight-test plan is the heart of all professional flight testing. The plan should account for every hour spent in the flight-test phase and you should adhere to it with the same respect for the unknown that all successful test pilots share. The time allotted for each phase of a personalized flight-test plan may vary, and each phase may have more events or checks than suggested in this AC, but your goals, should be the same. You should add flight-test operational and performance data to the aircraft’s flight manual so you can reference the data prior to each flight.
This document is cancelled. Cancelled by 90-89C. Check the official source before relying on it.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Amateur-Built Aircraft and Ultralight
Flight Testing Handbook
Date: 4/27/15 Initiated by: AFS-350
AC No: 90-89B Change:
This advisory circular (AC) provides suggestions and safety related recommendations primarily to assist amateur and ultralight builders in developing individualized aircraft flight-test plans. It also provides guidance for experimental light sport aircraft flight testing after modifications to the aircraft. It provides recommendations and suggestions you can combine with other sources on test flying, such as the aircraft plan/kit manufacturer’s flight testing instructions and other flight testing data. This will help you develop a detailed flight-test plan, tailored for your aircraft and resources.
This AC is not mandatory and does not constitute a regulation.
This AC attempts to make you aware that test flying an aircraft is a critical undertaking, which you should approach with thorough planning, skill, and common sense. The flight-test plan is the heart of all professional flight testing. The plan should account for every hour spent in the flighttest phase and you should adhere to it with the same respect for the unknown that all successful test pilots share. The time allotted for each phase of a personalized flight-test plan may vary, and each phase may have more events or checks than suggested in this AC, but your goals, should be the same. You should add flight-test operational and performance data to the aircraft’s flight manual so you can reference the data prior to each flight.
This AC is not mandatory and does not constitute a regulation. This AC describes an acceptable means, but not the only means, to develop flight-test plans. However, if you use the means described in the AC, you must follow it in all important respects. This AC applies to amateur and ultralight builders, and individuals involved in flight testing those aircraft.
John S. Duncan Director, Flight Standards Service
Contents
CONTENTS Paragraph Page
CHAPTER 1. PREPARATION … 1
Section 1. Homework … 1
1-1. Objective … 1
Section 2. Airport Selection … 4
1-2. Objective … 4
Section 3. Emergency Plans and Equipment … 6
1-3. Objective … 6
Section 4. Test Pilot … 9
1-4. Objective … 9 1-5. General … 9 1-6. Test Pilot Requirements … 9
Section 5. Medical Facts for Pilots … 11
1-7. Objective … 11
Section 6. Transporting the Aircraft to the Airport … 13
1-8. Objective … 13
Section 7. Assembly and Airworthiness Inspection … 14
1-9. Objective … 14 1-10. General … 14 1-11. Fitness Inspection—Airframe … 14 1-12. Field Check … 16
Section 8. Weight and Balance … 19
1-13. Objective … 19 1-14. Determining Empty Weight CG … 20 1-15. Determining Takeoff Weight CG … 21 1-16. Adding Additional Equipment … 22
Section 9. Paperwork … 24
1-17. Objective … 24
Section 10. Powerplant Tests … 26
1-18. Objective … 26
Section 11. Additional Engine Tests … 31
1-19. Objective … 31
Section 12. Propeller Inspection … 35
1-20. Objective … 35
Page iii
1-21. Recommendations for All Propellers … 35 1-22. Propeller Tracking Check … 37 1-23. Metal Propeller Inspection … 37 1-24. Wood Propeller Inspection … 38 1-25. Composite Propeller Inspection … 39
CHAPTER 2. TAXI TESTS … 41
Section 1. Low-Speed Taxi Tests … 41
2-1. Objectives … 41 2-2. Taxi Tests … 41
Section 2. High-Speed Taxi Tests … 42
2-3. Objective … 42
CHAPTER 3. THE FIRST FLIGHT … 45
Section 1. General … 45
3-1. Objective … 45 3-2. General … 45 3-3. Recommendations … 45 3-4. First Flight Inspection … 46
Section 2. The Role of the Chase Plane … 47
3-5. Objective … 47 3-6. General … 47
Section 3. Emergency Procedures … 48
3-7. Objective … 48 3-8. General … 48
Section 4. First Flight … 49
3-9. Objectives … 49
Section 5. First Flight Procedures … 51
3-10. Objective … 51
CHAPTER 4. THE FIRST 10 HOURS … 55
Section 1. The Second Flight … 55
4-1. Objective … 55
Section 2. The Third Flight … 55
4-2. Objective … 55 4-3. General … 55
Section 3. Hours 4 through 10 … 56
4-4. Objective … 56
Page iv
4-5. General … 56 4-6. Gear Retraction … 56 4-7. Climbs and Descent … 57 4-8. Airspeed In-Flight Accuracy Check … 58
CHAPTER 5. EXPANDING THE ENVELOPE … 61
Section 1. General … 61
5-1. Objective … 61
Section 2. Hours 11 through 20 … 61
5-2. Objective … 61 5-3. Stalls … 63
Section 3. Hours 21 through 35: Stability and Control Checks … 66
5-4. Objective … 66 5-5. General … 66 5-6. Definitions … 67
Section 4. A Word or Two about Flutter … 70
5-7. Objective … 70 5-8. Description … 71
Section 5. Spins … 72
5-9. Objective … 72 5-10. Caution … 73 5-11. Planning the Flight … 73
Section 6. Accelerated Stalls … 74
5-12. Objective … 74
CHAPTER 6. PUTTING IT ALL TOGETHER: 36 HOURS TO —————? … 77
Section 1. Maximum Gross Weight Tests … 77
6-1. Objective … 77
Section 2. Service Ceiling Tests … 78
6-2. Objective … 78
Section 3. Navigation, Fuel Consumption, and Night Flying … 79
6-3. Objectives … 80
CHAPTER 7. THOUGHTS ON TESTING CANARD TYPE AMATEUR-BUILT
AIRCRAFT … 83
Section 1. Canards … 83
7-1. Objective … 83
Page v
Section 2. Flight Test Considerations … 84
7-2. General … 84
CHAPTER 8. ULTRALIGHT AIRFRAME INSPECTION … 87
Section 1. Differences … 87
8-1. Objectives … 87 8-2. Definition … 87
Section 2. The Test Pilot … 88
8-3. General … 88
Section 3. Pre-Flight Airframe Inspection … 89
8-4. General … 89 8-5. Checklist … 89
CHAPTER 9. ULTRALIGHT ENGINE/FUEL SYSTEM INSPECTION … 93
Section 1. Engine Inspection … 93
9-1. Objective … 93
Section 2. Fuel Systems … 95
9-2. General … 95
CHAPTER 10. ULTRALIGHT TEST FLYING RECOMMENDATIONS … 97
Section 1. Three Recommendations … 97
10-1. Objective … 97 10-2. Recommendations … 97
Section 2. Airport Selection … 98
10-3. Objective … 98
Section 3. Taxiing … 98
10-4. General … 98
Section 4. First Flight Differences … 98
10-5. Use of Power … 98 10-6. Control Feel … 99 10-7. Stalls … 99 10-8. Steep Turns … 99
Section 5. Emergency Procedures … 99
10-9. Engine Failures … 99 10-10. Loss of Control … 99 10-11. Catastrophic Failure … 100
Page vi
LIST of Figures
APPENDIX 1. SAMPLE CHECKLIST FOR A CONDITION INSPECTION (9 pages) … 1 APPENDIX 2. SOURCES FOR ACCIDENT/INCIDENT INFORMATION (1 page) … 1 APPENDIX 3. ADDITIONAL REFERENCES ON FLIGHT TESTING (4 pages) … 1 APPENDIX 4. ADMINISTRATIVE INFORMATION (2 pages) … 1
LIST OF FIGURES
Figure 1. Runway Length Chart … 5 Figure 2. Empty weight CG … 20 Figure 3. Takeoff CG … 21 Figure 4. Additional Equipment Added … 22 Figure 5. 100 HP Fuel Flow Rate Chart … 34 Figure 6 Propeller Tracking … 36 Figure 7. Climb Airspeed and Altitude Graph … 64 Figure 8. Best Rate of Climb Speed Graph … 65 Figure 9. Static Stability … 67 Figure 10. Time … 68
Page vii
1-1. OBJECTIVE. A planned approach to flight testing. › c. Time Required for Flight Testing Amateur-Built Aircraft. Your…
CHAPTER 1. PREPARATION
“The Laws of Aerodynamics are unforgiving and the ground is hard.” Michael Collins (1987)
SECTION 1. HOMEWORK
“If you have no plan—you have no goal.” Harold Little, Aircraft Manufacturer (1994)
1-1. OBJECTIVE. A planned approach to flight testing.
a. Develop a Flight-Test Plan. Your most important task is to develop a comprehensive flight-test plan. You should tailor this plan to define the aircraft’s specific level of performance, so it’s important that the entire flight-test plan be developed and completed before the aircraft’s first flight.
NOTE: As part of the comprehensive flight-test plan, the test pilot should read and comprehend this entire AC before proceeding in accomplishing any suggested task.
b. Objective of a Flight-Test Plan. The objective of a flight-test plan is to determine the aircraft’s controllability throughout all the maneuvers and to detect any hazardous operating characteristics or design features. You should use this data to develop a flight manual that specifies the aircraft’s performance and defines its operating envelope. Additionally, the plan should reference the use of checklists to assure that all relevant steps and elements are covered.
c. Time Required for Flight Testing Amateur-Built Aircraft. Your original issued airworthiness certificates should be limited to operation within an assigned flight-test area for a
(1) Flight testing in some form is advisable following any modification… › (2) This sort of flight testing is at the sole discretion of the owner…
minimum of 25 hours when a type certificated (TC) engine/propeller combination is installed. A minimum of 40 hours is required when a non TC’d engine, propeller, or engine/propeller combination is installed. Furthermore, if the TC’d engine, propeller, or engine/propeller combination installed has been altered in a way that differs from an approved type design in a Type Certificate Data Sheet (TCDS), a minimum of 40 hours shall be required.
d. Time Required for Flight Testing Experimental Light Sport Aircraft (ELSA). If you own an ELSA experimental aircraft under Title 14 of the Code of Federal Regulations (14 CFR) part 21, § 21.191(i)(2), and it has not been modified, conduct a test flight as per their operations manual in an assigned flight-test area for a minimum of 5 hours. This applies for all classes of light sport aircraft (LSA) to determine aircraft controllability throughout its design limits.
e. Best Practices for Flight Testing After Modifying an Experimental Amateur-Built Aircraft. Before considering any modification to an aircraft previously issued an experimental certificate for the purpose of operating as an amateur-built (E-AB) aircraft, there are two things you need to consider. First is the level of modification; the other is the corresponding flight testing required for the modification. When considering the level of modification, you should first check the E-AB operating limitations. They will detail what, if any, reporting requirements there are for a given modification. This is especially important when the E-AB modification approaches the same level of a major change to TC aircraft as defined in part 21, § 21.93. Usually the owner of the E-AB aircraft is required by the aircraft operating limitations to notify the geographical responsible Flight Standards District Office (FSDO) following a “major change” as defined by § 21.93. This regulation states that a “major change” is any that affects the “weight, balance, structural strength, reliability, operational characteristics, or other characteristics affecting the airworthiness of the product. The corresponding flight testing for a major change will require at least 5 hours minimum of supplemental Phase I flight testing be completed to comply with 14 CFR part 91, § 91.319(b). The aircraft owner must obtain concurrence from the FSDO as to the suitability of the proposed test area.
(1) Flight testing in some form is advisable following any modification to the aircraft. Not only will a structured series of test flights reveal any malfunctions or unintended consequences associated with a modification, but it will also allow the pilot to become familiar with the operation of the aircraft after a given change before returning to “operational” flying. For example, flight testing a new instrument will verify its proper operation and ensure the pilot understands how to use it. This is important to accomplish before operating the aircraft in a situation where the proper operation of the instrument may affect the safe outcome of the flight.
(2) This sort of flight testing is at the sole discretion of the owner or pilot, so it may or may not be as formal as Phase I. In general, however, the owner or pilot should conduct it in uncongested airspace local to an airport, to keep distractions at a minimum. Passengers flying for the sole purpose of pleasure should be avoided, however, because this is not Phase I testing, a passenger may be carried to monitor aircraft systems or perform other functions relevant to the purpose of the flight, if appropriate. As with any test flight, there should a clear plan with clear objectives.
f. Modifying ELSAs. All alterations, modifications, and additions or… › (2) Following any major change, your ELSA must be assigned to a…
(3) It is important to note that, while some modifications are neither mandatory nor necessary to report to the FSDO, you should document all changes appropriately. The aircraft records should be updated with the date the work was completed, the hours in service of the components affected, and the total hours on the aircraft noted in the logbook along with the changes performed and the equipment added or removed. The weight and balance data and the equipment list should also be updated. Note the areas that affect operational differences in the pilot’s operating handbook (POH). In situations where the changes affect installed or needed placards and decals, they should be in place before flying with the new configuration.
(4) If the major change includes installing a different type of engine (reciprocating to turbine) or a change of a fixed-pitch from or to a controllable propeller, the aircraft owner must fill out a revised FAA Form 8130-6 to update the aircraft’s file in the FAA Aircraft Registration Branch (AFS-750). You must conduct all operations under day visual flight rules (VFR) in a sparsely populated area. The aircraft must remain in flight test for a minimum of 5 hours.
(5) At the completion of flight testing, the results should be posted in the aircraft log. Changes should be incorporated into the POH and other affected records. The statement should, at a minimum, state the scope of the changes, the tests performed along with the results. The total hours as of that date on the aircraft should be included, and the aircraft be declared to be in a condition for safe operation.
f. Modifying ELSAs. All alterations, modifications, and additions or deletions to your ELSA must be approved in writing by the LSA kit manufacturer and recorded in the aircraft records before the original certification in experimental purpose for operation of LSA under § 21.191(i)(2).
(1) Additionally for a major change to your ELSA (such as an alteration, modification, addition, or deletion), the FAA has the authority under part 91 § 91.319(i) to modify your experimental LSA operating limitations with special restrictions for flight testing due to the aircraft modification.
(2) Following any major change, your ELSA must be assigned to a flight-test area for an appropriate time to conduct a flight test and evaluate that your aircraft is in a condition for safe operation. The guidance baseline for this testing is 5 hours of flight time within the flight-test area. The FAA may prescribe any additional limitations and/or flight time within the flight-test area deemed necessary in the interest of safety.
1-2. OBJECTIVE. To select an airport to test fly the aircraft. › b. Ideal Runway. The ideal runway at sea-level elevation should be at…
SECTION 2. AIRPORT SELECTION
“An airport should be chosen with the same care and consideration as getting a second doctor’s
opinion.” Fred Wimberly, EAA Flight Test Advisor (1994)
1-2. OBJECTIVE. To select an airport to test fly the aircraft.
a. Runway Alignment. The airport should have one runway aligned into the prevailing wind with no obstructions on the approach or departure end. Hard surface runways should be in good repair and well maintained to avoid foreign object damage (FOD) to the propeller and landing gear. Grass fields should be level with good drainage. Avoid airports in densely populated or developed areas and those with high rates of air traffic. The runway should have the proper markings with a windsock or other wind direction indicator nearby.
b. Ideal Runway. The ideal runway at sea-level elevation should be at least 4,000 feet long and 100 feet wide. For each 1,000-foot increase in field elevation, add 500 feet to the runway length. If testing a high-performance aircraft, the airport’s runway at sea level should be more than 6,000 feet long and 150 feet wide for a wider margin of safety. You should factor other considerations, such as power-to-weight ratio, wing design, and density altitude, into the equation for picking the best runway for the initial flight testing. You can also use the chart in Figure 1.
1-2. OBJECTIVE. To select an airport to test fly the aircraft. › g. Local Management. Explain the flight-test program and emergency…
FIGURE 1. RUNWAY LENGTH CHART
Takeoff Distance in feet
A - Distance to takeoff at minimum smooth lift-off speed, fly for 5 seconds at that speed
without climbing, land, and stop straight ahead. B - Distance to reach minimum smooth lift-off speed. C - Distance covered in 5 seconds of flight at minimum smooth lift-off speed. D - Distance to stop from minimum smooth lift-off speed (includes air and ground
distance). E - Distance to takeoff at slow approach speed and climb thereafter at an angle of
1 in 20 to 50 ft. altitude, this distance will allow most airplanes to accelerate to normal climb speed before crossing end of runway.
c. Emergency Fields. Identify emergency landing fields located within gliding distance from anywhere in the airport pattern altitude. Since engine failures are second only to pilot error as the major cause of amateur-built aircraft accidents, preparations for this type of emergency should be a mandatory part of the flight-test plan.
d. Communications. You should perform flight tests from an airport with an active Unicom or tower, even if the aircraft either doesn’t have an electrical system or doesn’t have a radio. Even at an uncontrolled field, you should improvise a communications base. For both situations, the FAA recommends a handheld radio with aviation frequencies and a headset with a microphone and a push-to-talk switch. Good radio communications improves the overall level of safety and reduces cockpit workload.
e. Physical Space. The FAA recommends you also consider the availability of hangar space and ramp areas. These facilities will provide protection from inclement weather and vandalism while the aircraft is being tested, maintained, and inspected.
f. Safety. The airport should have a telephone and firefighting equipment complying with relevant municipal codes.
g. Local Management. Explain the flight-test program and emergency plans to the airport manager or owner who may help you obtain temporary hangar space, provide ground/air communications, and supply emergency equipment for use during the flight test.
SECTION 3. EMERGENCY PLANS AND EQUIPMENT
b. Ground Emergencies. The ground emergency plan should train the… › (4) The master switch location and its OFF position.
“The object of the game, gentlemen, is not to cheat death: the object is not to let him play.”
Patrick Poteen, Sgt. U.S. Army
1-3. OBJECTIVE. To develop a flight-test plan with two sets of emergency plans; one for in-flight emergencies and another for ground emergencies.
a. In-Flight Emergencies. Your in-flight emergency plan should address the following:
(1) Complete or partial engine failure, especially after takeoff.
(2) Flight control problems and severe out-of-rig conditions.
(3) Fire in the engine compartment or cockpit.
b. Ground Emergencies. The ground emergency plan should train the ground crew and/or airport fire department crash crew on:
(1) The airplane canopy or cabin door latching mechanism.
(2) The pilot’s shoulder harness/seat belt release procedure.
(3) The location and operation of the fuel shut-off valve.
(4) The master switch location and its OFF position.
1-3. OBJECTIVE. › h. Pilot Protection. A modern aviation/motorcycle helmet, a properly…
(5) The magneto switch location and its OFF position.
(6) Engine cowling removal procedures to gain access to the battery location or for firefighting.
(7) The battery location and disconnect procedures.
(8) Fire extinguisher application and use.
(9) How to secure a ballistic parachute system.
c. Ground Crew. A minimum ground crew of two experienced persons should support every test of an amateur built aircraft. Your ground crew’s function is:
(1) To ensure that the aircraft is in airworthy condition for safe operation.
(2) To provide assistance to the test pilot in an emergency.
d. The Airport.
(1) If the airport does not have a fire rescue unit, the FAA suggests the ground crew have a four-wheel-drive vehicle equipped with a portable radio, first aid kit, metal-cutting tools, and a fire extinguisher. At least one person should have completed first aid training.
(2) If the airport provides a fire rescue unit, the test pilot should ensure the rescue unit and the ground crew are trained and competent in performing ground emergency functions as identified in the flight-test plan.
(3) For a small donation, some local volunteer fire and rescue companies may provide standby crew during the initial critical portions of the flight-test phase.
e. Hospital Location. The ground crew should know the location and telephone numbers of the hospitals and fire rescue squads in the vicinity of the airport and the flight-test area. If the test pilot is allergic to specific medications, or has a rare blood type, the test pilot should carry or wear a medical alert bracelet or card to alert medical personnel of the condition.
f. Fire Extinguisher. Fire extinguishers should be available to the ground crew, and a fire extinguisher should be securely mounted in the cockpit within easy reach of the test pilot. A fire axe, or other tool capable of cutting through the canopy, also should be in the cockpit.
g. Fire Protection. There is always danger of a flash fire during test flights. To prevent burns, the pilot should wear an aviation/motorcycle helmet, NOMEX coveralls/gloves, and smoke goggles. If NOMEX clothing is not available, cotton or wool clothing will offer some protection from heat and flames. Pilots should never wear nylon or polyester clothing because synthetic materials melt when exposed to heat and will stick to the skin.
h. Pilot Protection. A modern aviation/motorcycle helmet, a properly installed shoulder harness, a well-designed seat, a clean cockpit design free of protruding components/sharp edges,
(2) Installation Considerations. › (g) The placement of the activating handle in the cockpit.
NOMEX clothing, smoke goggles, and a memorized emergency plan ensure safety during flight testing.
i. Parachute. The decision to wear a parachute depends on the type of aircraft you are testing. Some aircraft have forward hinged canopies without quick release pins, or have pusher propellers, increasing the chance of injury to the pilot while exiting the aircraft. Other aircraft designs may pose no exit problems. If the pilot decides to wear a parachute, check that a qualified parachute rigger has packed the parachute within 180 days. Ensure that the parachute has not been exposed to rain/moisture and, when worn, does not interfere with cockpit management. The test pilot should be thoroughly trained on how to exit the aircraft and deploy the parachute.
j. Ballistic Parachutes. Ballistic parachutes are the latest development in dealing with in-flight emergencies. A ballistic parachute is attached to the aircraft and when activated, lowers the whole aircraft and the pilot to the ground at the rate of descent of about 20 feet per second or about 1,200 feet per minute.
(1) Deployment Scenarios. You might deploy a ballistic parachute in case of:
(a) Structural failure.
(b) Mid-air collision.
(c) Stall/spin.
(d) Loss of control/icing.
(e) Engine failure over bad terrain.
(f) Pilot incapacitation.
(2) Installation Considerations. You should consider the following when installing a ballistic parachute:
(a) Match the parachute to the aircraft’s size, weight, and Vne speed. Check with the parachute manufacturer.
(b) How to position and mount the parachute.
(c) The parachute’s effect on the aircraft’s weight and balance before deployment and aircraft’s touchdown attitude after deployment.
(d) Compatibility of the opening loads and the aircraft’s structural design limits.
(e) The routing of the bridle and harness.
(f) The routing of the activating housing.
(g) The placement of the activating handle in the cockpit.
b. Suggested Test Pilot Flight Time Requirements. Each test pilot must… › (3) A minimum of 50 recent takeoffs and landings in a tailwheel…
(h) Incorporation of parachute deployment procedures in the in-flight emergency plan and emergency checklist.
(i) The deployment time, from activation to full parachute opening.
(3) Inspection Recommendations. If a ballistic parachute is installed, the builder should add the appropriate ballistic parachute inspection items to the aircraft’s preflight inspection checklist. The builder also should add the ballistic parachute manufacturers repack/refitting schedule and maintenance inspections to the flight manual and the conditional annual inspection checklist.
SECTION 4. TEST PILOT
“We are looking for a few good Men and Women!” Marine Corps advertisement (1991)
1-4. OBJECTIVE. Select a qualified individual as the test pilot.
1-5. GENERAL. The test pilot should be competent in an aircraft of similar configuration, size, weight, and performance to the test aircraft.
1-6. TEST PILOT REQUIREMENTS.
a. Minimum Requirements. A test pilot should meet the following minimum qualifications:
(1) Physically fit: Test flying an aircraft is a stressful and strenuous task.
(2) No alcohol or drugs in the last 24 hours.
(3) Rated, current, and competent in the same category and class as the aircraft being tested.
(4) Current medical and biennial or flight review as appropriate, or a current USUA certification and flight review.
b. Suggested Test Pilot Flight Time Requirements. Each test pilot must assess if his or her level of competency is adequate, or if additional flight training is necessary. If you determine you are not qualified to flight test an unproven aircraft, you must find someone who is qualified. The following suggested number of flight hours is only an indication of pilot skill, not an indicator of pilot competence.
(1) One hundred hours solo time before flight testing a kit plane or an aircraft built from a time-proven set of plans.
(2) Two hundred hours solo time before flight testing a unique design or high-performance aircraft.
(3) A minimum of 50 recent takeoffs and landings in a tailwheel aircraft) if the test aircraft is tailwheel equipped.
c. Pilot Recommendations. The test pilot should: › (12) Use checklists for both normal and emergency actions and…
c. Pilot Recommendations. The test pilot should:
(1) Be familiar with the airport and the surrounding terrain that could be used for emergency landing fields in the area.
(2) Talk with and, if possible, fly with a pilot in the same kind of aircraft to be tested; the Experimental Aircraft Association (EAA) maintains a list by state of instructors that hold a Letter of Deviation Authority (LODA). The experimental aircraft model used by the instructor for the purposes of type-specific training is also listed. This list changes often and can be found at: http://www.eaa.org/govt/loda.asp.
(3) Take additional instruction in similar TC’d aircraft, as addressed in AC 90-109, Airmen Transition Experimental or Unfamiliar Airplanes. For example, if the aircraft to be tested is tailwheel equipped, a Bellanca Citabria or Super Cub is appropriate for training. For testing an aircraft with a short wingspan, the Grumman American Yankee or Globe Swift is suitable for training.
(4) For amateur aircraft built from commercial kit manufacturers, consider using an additional pilot, as referenced in AC 90-116, Additional Pilot Program for Phase I Flight Test.
(5) Be considered competent when the test pilot has demonstrated a high level of skill in all planned flight-test maneuvers in aircraft with performance characteristics similar to the test aircraft.
(6) Study the ground and in-flight emergency procedures developed for the aircraft and practice them in aircraft with similar flight characteristics.
(7) Have logged a minimum of 1 hour of training in recovery from unusual attitudes within 45 days of the first test flight.
(8) Have logged a minimum of 10 tailwheel take-off and landings within the past 30 days, if appropriate.
(9) Study the performance characteristics of the aircraft to be tested. Refer to the designer’s or kit manufacturer’s instructions, articles written by builders of the same make and model aircraft, and study actual or video tape demonstrations of the aircraft.
(10) Review the FAA/National Transportation Safety Board (NTSB)/EAA accident reports for the same make and model aircraft to be aware of problems the aircraft has experienced during previous operations (see appendix 2 for the address).
(11) Memorize the cockpit flight controls, switches, valves, and instruments. A thorough knowledge of the cockpit will result in controlled and coordinated mental and physical reactions during emergencies.
(12) Use checklists for both normal and emergency actions and procedures. The Emergency procedures should be also memorized. Add additional notes on the instrument panel to aid in their use if necessary.
f. Ear and Sinus Pain. › (1) Ear and sinus pain is usually caused by the eardrum or sinuses…
NOTE: The EAA has developed a Flight Advisor Program which offers builders/pilots assistance in performing a self-evaluation of the flight-test program and/or selection of the test pilot. To obtain additional information, see the following EAA Web page: http://www.eaa.org/flightadvisors.
SECTION 5. MEDICAL FACTS FOR PILOTS
“If the pilot is unairworthy, so is the airplane!” Bill Chana, Aeronautical Engineer
1-7. OBJECTIVE. Identify well-known medical causes for aircraft accidents and stress the importance of a personal pre-flight checklist in addition to an aircraft pre-flight checklist.
a. Alcohol. Test flying an aircraft places additional mental and physical demands on the pilot. In addition to the 8 hour requirement of part 91, § 91.17, General Operating and Flight Rules, the FAA strongly recommends a minimum of 24 hours between the last drink and the test flight. This is because small amounts of alcohol in the blood stream can affect judgment and reaction time, and decrease a pilot’s tolerance to hypoxia.
b. Anesthetics. Local and dental anesthetic can affect a pilot’s performance in many adverse ways. The FAA recommends that a minimum of 48 hours elapse from the time of anesthesia to the time the pilot climbs into the cockpit.
c. Blood Donations. If you donate 1 unit or 500 ml of blood or less, the FAA recommends that you do not pilot an aircraft for 24 hours; if you give more than 1 unit or more than 500 ml, the FAA recommends that you do not pilot an aircraft for 72 hours. Although the physical effects may not be noticeable at sea level, they will become apparent when flying at higher altitudes.
d. Carbon Monoxide (CO). CO is a colorless, odorless, tasteless gas that is always present in engine exhaust fumes. CO prevents oxygen absorption by the blood, and exposure to the gas creates vision problems, headaches, disorientation, and diminished rational thinking. See the current edition of AC 20-23, Carbon Monoxide (CO) Contamination in Aircraft Detection and Prevention.
e. Drugs. Similar to alcohol, illegal drugs will reduce or impair judgment and affect reflexes and hand/eye coordination. Prescription drugs and over-the-counter remedies may be dangerous when combined with flying. The FAA recommends that all pilots who must take medication consult with an aviation medical examiner (AME) to understand the medication’s effects on their ability to think and react while in the cockpit.
f. Ear and Sinus Pain.
(1) Ear and sinus pain is usually caused by the eardrum or sinuses failing to equalize the air pressure during a descent. Blocked ears and sinuses can be caused by a head cold. The pain can be considerable and is most noticeable during descents. For ear blockages try yawning, swallowing, or chewing gum which may give some relief. The Valsalva procedure—pinch the nose, close the mouth, and try to force air through the nostrils— can be effective.
1-7. OBJECTIVE. › j. Stress. Stress from the pressures of a job and everyday living can…
(2) If ear blockage occurs during flight, try climbing back to a higher altitude—lower air pressure—until the pain lessens. Then begin a gradual rate of descent, giving the ears and sinuses time to adapt to the increasing pressure.
(3) After landing, nasal sprays will give some sinus pain relief. To relieve ear pain, wet paper towels with hot water and place in the bottom of two cups. Hold the cups over the ears—the warmth will help ease the inflamed tissues and reduce the pain. If pain continues, see a doctor.
NOTE: The best way to avoid this problem is not to fly with a head cold, upper respiratory infection, or nasal allergic condition. Be advised that some nasal and oral decongestants could be ineffective at altitude and have side effects such as drowsiness that can significantly impair pilot performance. Again, consult with an AME to understand the effects of medication before flying.
g. Fatigue. Fly only when healthy, fit, and alert. Mental and physical fatigue will generally slow down a pilot’s reaction time and affect decision-making and attention span. Lack of sleep is the most common cause of fatigue, but family and business problems can create mental fatigue which can have the same effects on the pilot as lack of sleep.
h. Flicker Vertigo. Light, when flashing at a frequency between 4 to 29 cycles per second, can cause a dangerous physiological condition in some people called flicker vertigo. These conditions range from nausea and dizziness to unconsciousness or even reactions similar to an epileptic episode. When heading into the sun, a propeller cutting the light may produce this flashing effect. Avoid flicker vertigo, especially when the engine is throttled back for landing. To alleviate this when the propeller is causing the problem, frequently change engine revolutions per minute (rpm). When flying at night and the rotating beacon is creating flicker vertigo, turn it off.
i. Underwater Diving. Never fly immediately after scuba diving. Always allow 24 hours to elapse before flying as a pilot or a passenger in order to give the body sufficient time to rid itself of excessive nitrogen absorbed during diving.
j. Stress. Stress from the pressures of a job and everyday living can impair a pilot’s performance, often in subtle ways. A test pilot may further increase the stress level by setting unreasonable test flying schedules in order to meet an arbitrary “done by date.” Stress also may impair judgment, inducing the pilot to take unwarranted risks, such as flying into deteriorating weather conditions or flying when fatigued to meet a self-imposed deadline.
1-8. OBJECTIVE. Reduce damaging the aircraft in transit. › h. Ensure the designated driver has recent experience driving a…
SECTION 6. TRANSPORTING THE AIRCRAFT TO THE AIRPORT
“Best laid plans of mice and men are often stuck in traffic.”
Ben Owen, EAA Executive Director (1994)
1-8. OBJECTIVE. Reduce damaging the aircraft in transit.
a. Use a truck or flatbed truck/trailer large enough to carry the aircraft and the additional support equipment.
b. If the aircraft wings are removable, build padded jigs, cradles, or fixtures to hold and support them during the trip to the airport.
c. Secure the fixtures to the truck/trailer, and then secure the wings to the fixture.
d. Use two or more ropes at each tie down point.
e. Use heavy moving pads used for household moves to protect wings and fuselage. Most rent-a-truck firms offer them for rental.
f. During the planning stage, obtain applicable permits and follow the local ordinances for transporting an oversized load. Ask the local police if they can provide an escort to the airport.
g. Brief the moving crew thoroughly before loading and unloading the aircraft.
h. Ensure the designated driver has recent experience driving a truck/trailer and is familiar with the roads to the airport.
SECTION 7. ASSEMBLY AND AIRWORTHINESS INSPECTION
“Complacency is one of the major causes of accidents, no matter how well things are going, something can go wrong” Art Scholl
Section 7. ASSEMBLY AND AIRWORTHINESS INSPECTION › 1-11. FITNESS INSPECTION—AIRFRAME.
1-9. OBJECTIVE. To determine the airworthiness of the aircraft and its systems.
1-10. GENERAL.
a. If you must reassemble the aircraft after moving it to the airport—take time to do so carefully. This is a critical event because mistakes can easily occur due to the builder’s preoccupation with the impending first flight of the aircraft. One of the most common and deadly mistakes is to reverse the rigging on the ailerons. To prevent errors in reassembling the aircraft, follow the designer’s or kit manufacturer’s instructions, or use a written checklist specifically designed as part of the flight-test plan. At the completion of each major operation, have another expert check the work.
b. After reassembling the aircraft, perform a pre-flight “fitness inspection.” This inspection should be similar to an annual inspection. You should perform the fitness inspection even if the FAA has just issued a special airworthiness certificate for the aircraft. Even if a builder was 99 percent perfect and performed 10,000 tasks building the aircraft, there would still be a hundred items that would need to be found and corrected before the first flight.
1-11. FITNESS INSPECTION—AIRFRAME. A builder-developed comprehensive post assembly checklist should be used, and the results of that inspection should be recorded on the checklist to provide increased assurance that all items of concern have been addressed and the
f. Instrument Panel. › (1) All the instruments should be properly secured in the panel and…
results documented. The following additional safety checklist items may not be applicable to all amateur-built make and model aircraft, but the FAA presents them here for consideration and review.
a. Control Stick/Wheel. The control stick/wheel should have a free and smooth operation throughout its full range of travel. There should be no binding or contact with the sides of the fuselage, seat, or instrument panel. There should be no free play (slack) in the controls, nor should the controls be tight as to have stick-slip movement.
b. Rudder Pedals. Move the rudder pedals through the full range of travel. The pedal movement should be smooth, and without any binding. The test pilot’s shoes should not catch on exposed metal lines, fixtures, or electrical wire harness.
c. Brakes. Hand and/or toe brake pressure should be firm with no tendency to bleed down or lock up. Spongy brakes that must be “pumped up,” or that show a drop in the brake fluid reservoir level after a few brake applications, indicates a brake fluid or air leak in the system.
d. Main Landing Gear. Ensure that the gear attach points, shimmy damper, bungees, wheels, brakes, and wheel fairings are airworthy. If applicable, check that the tailwheel pivot point is centered and vertical compared to the longitudinal axis of the aircraft. It is critical that the main landing gear alignment toe in/toe out is zero or matches the specifications for fuselage/landing gear alignment called out in the plans. Even one landing gear wheel out of alignment can cause a ground loop.
e. Control Surfaces. Perform rigging checks to ensure that control input for ailerons, rudder, elevators, and trim tabs results in the correct amount of travel and direction of the control movement and that these control surfaces make contact with their stops. Also, ensure that the flaps, if installed, have the proper travel, operate as a single unit, and cannot be extended beyond the maximum extended position. It is important to ensure that the control cable tension is correct by (1) checking it with a calibrated tensiometer and (2) confirming that all the attachment hardware is secured and turnbuckles are properly safetied.
(1) If the cable tension is less than required by specifications, in-flight air loads will prevent full travel of the control, even if the control has the right amount of deflection and hits all the stops in the cockpit/wing/tail when tested on the ground. With low cable tension, the slack in the cables will absorb the desired control movement input.
(2) While checking cable tension, make sure there is no “free play” in the flight control hinges and rod ends. Free play and loose cable tension combined with control mass imbalance can bring on control surface “flutter.” Do not, however, rig the controls at too high a cable tension. This will cause high wear rate on the pulleys and prevent good control feel, especially at low airspeeds.
f. Instrument Panel.
(1) All the instruments should be properly secured in the panel and have preliminary markings on them. The airspeed indicator and engine tachometer should be marked with the
1-12. FIELD CHECK. › a. Airspeed Check. Slip a long rubber hose over the pitot mast (The FAA…
expected performance range markings. Oil temperature and oil pressure must have the engine manufacturer’s recommended operating range marked. If the markings are on the instrument glass face, paint a white slippage mark on both the glass and on the instrument case to alert the pilot in case the glass/range marks have moved. Attach a temporary placard to the instrument panel with the expected stall, climb, and glide speeds. It is a handy reference in times of emergency.
(2) Angle of attack systems may require in-flight calibration. Information displayed prior to that calibration may not be accurate.
(3) Electronic data collection systems, when installed, must be checked if possible before flight according to the manufacturer’s instructions. Recording of electronic data through flight and engine instruments can be very useful, but only if it is ensured that accurate information is being collected. Therefore, verification of this data prior to flight is important.
g. Behind the Instrument Panel. Very few amateur-built aircraft of the same make and model have the same instrument panel design. Amateur builders should inspect this area to ensure that all line connections are tight, that nothing interferes with control travel, and there are no loose wires or fuel, oil, or hydraulic leaks.
h. Carbon Monoxide (CO). CO leaks also can be performed. Wait until night or put the aircraft in a dark hangar. Climb into the cockpit and have a friend shine a bright flood light close to the firewall. If light leaks into the cockpit, CO can seep in. Mark it and seal it.
i. Engine and Propeller Controls. All controls should be visually inspected, move in the proper direction, and securely mounted. The friction lock on both controls should be checked for operation. Each control should have full movement with at least a ¼-inch of “cushion” at the full travel position. The control cables should be firmly attached to the fuselage along each 24 inches of their runs to prevent whipping of the cable and loss of cable movement at the other end. Control cables with ball sockets should have large area washers on either end of the bolt connection. This will ensure the control will remain connected, even if the ball socket fails and drops out.
j. Static System. The best procedure to check the altimeter for leaks and accuracy is to have the entire static system checked using 14 CFR part 43, appendix E, at an FAA-approved repair station.
1-12. FIELD CHECK. You need two people to accomplish the following field check by which an amateur-builder can detect if the aircraft’s instrument system is leaking:
NOTE: This field check is not an accuracy check. Additionally, you should check the manufacturer’s manuals for the installed pitot-static instruments to ensure that this test method will not damage any associated electronics.
a. Airspeed Check. Slip a long rubber hose over the pitot mast (The FAA recommends surgical tubing). As one person reads the airspeed, the other should very slowly roll up the other end of the tubing. This will apply pressure to the instrument. When the airspeed indicator needle reaches the aircraft’s approximate recommended cruise speed, pinch the hose shut, and hold that
c. Fuel System. Since 1983, more than 70 percent of the engine failures… › (2) When filling the tanks, place the aircraft in the straight and…
reading. The airspeed needle should remain steady for a minute if the system is sound. A fast drop off will indicate a leak in the instrument, fittings, lines, or the test hose attachment. Never force air in the pitot tube or orally apply suction on a static vent—this action will damage the instruments.
b. Altimeter/Vertical Speed Check.
(1) To check the static side, apply low suction at the end of the static vent port. The easiest way to gain access to the static system is to remove the static line at the static port. If there are two static ports, tape the unused port closed. Next, get two feet of surgical tubing, seal one end, and tightly roll it up. Attach the open end to the static line and slowly unroll the tubing. This will apply a suction, or low pressure, to the static system.
(2) The altimeter should start to show an increase in altitude. The vertical speed indicator also should indicate a rate of climb. The airspeed may show a small positive indication. When the altimeter reads about 2,000 feet, stop and pinch off the tube. There will be some initial decrease in altitude and the vertical speed will read zero. The altimeter should then hold the indicated altitude for at least a minute. If altitude is lost, check for leaks.
NOTE: The above airspeed and altimeter field checks are a check of the system for possible leaks, and are not the same as airspeed or static system accuracy tests done by a certificated repair station. The checks do not include the pitot tube and static ports located on the airframe. The FAA recommends the builder not deviate from the designer’s original plans when installing the pitot and static system.
c. Fuel System. Since 1983, more than 70 percent of the engine failures in amateur-built aircraft were caused by fuel system problems. Many times the direct cause of engine failure was dirt and debris in the fuel tank and lines left behind during the manufacturing process.
(1) Before filling the aircraft’s fuel tanks, the amateur-builder should vacuum any manufacturing debris from each tank and wipe them down with a “tack” cloth (available from a paint supply store). Next, the builder should flush the system with aviation grade gasoline several times in order to remove any small or hard to reach debris from the tanks and lines. The builder should also clean the fuel filter/gasolator screen/carburetor finger screen. The amount of time spent “sanitizing” the fuel system will provide big safety benefits for the life of the aircraft.
(2) When filling the tanks, place the aircraft in the straight and level cruise position. Add fuel in measured amounts to calibrate the fuel tank indicators. While allowing the aircraft to sit for a short time to observe for possible leaks, inspect the fuel tank vents to see if they are open and clear. Check that the fuel tank caps seal properly. If there are no leaks and the fuel system has an electric boost pump, pressurize the system and again check for leaks. The fuel selector, vents, and fuel drains should be properly marked and tested for proper operation.
NOTE: Many amateur-built aircraft take 5 to 8 years to build. During that time, many rubber-based oil and fuel lines and cork gaskets installed early in the building process may have age hardened, cracked, and/or turned brittle.
1-12. FIELD CHECK. › h. Canopy/Door Locks Checks. Ensure the canopy or doors on the aircraft…
The builder should carefully inspect these components and replace as necessary to prevent a premature engine failure.
d. Retractable Landing Gear System. If equipped with a retractable landing gear system, whether hydraulic, electrical, or mechanical, the system should function dependably and positively in accordance with the designer’s intent. The builder/pilot should rigorously cycle the retractable landing gear in the appropriate ground setup, using both the normal and emergency landing gear extension system. There should be no hang-ups or binding. If equipped, a function check of the weight on wheel switch and on-board landing gear indicators should also be performed.
e. Safety Belt and Shoulder Harness. You should check these items for condition and proper installation. A review of amateur-built aircraft accidents has disclosed a significant number of accidents in which the seat belt mounting hard points failed. You should check each seat belt and shoulder harness mounting hard point to the designer’s specifications so it will hold the harness and pilot in the aircraft at the ultimate design “G” load specification, both positive and negative, for the aircraft.
f. Avionics and Electrical Checks. Test the avionics systems. Perform an operational check to ensure the radio(s) transmit and receive on all frequencies. Inspect circuit breakers/fuses, microphones, and antennas for security and operation. Test the emergency locator transmitter for proper operation and battery life. Check electrical systems for operation of lights, instruments, and basic navigation/communication performance. You can check other electrical systems, such as generator/alternator output, during engine run-ins, taxi, and flight tests. Check the battery and the battery compartment for security and if applicable, proper venting to the outside of the aircraft. Check the condition of the engine-to-airframe bonding (grounding) wire. Ensure that all electrical instruments operate properly.
g. Cowling and Panel Checks. Ensure that all inspection panels are in place, the cowling is secured, and cowl flap operation is satisfactory. Inspect the propeller spinner and its backing plate for cracks.
h. Canopy/Door Locks Checks. Ensure the canopy or doors on the aircraft work as intended. Double check the canopy or door lock(s) so the canopy and doors will not open in flight and disturb the airflow over the wings and stall the aircraft. If a canopy jettison system is installed, check for proper operation when the aircraft on the ground and when it is on jacks. (Jacks will simulate flight loads on the aircraft.)
c. A Word about Lateral Balance. Aircraft lateral balance (side to… › (1) Aircraft that have fuel in the wings usually have one or more fuel…
SECTION 8. WEIGHT AND BALANCE
“Never argue with your spouse or a mathematician” Phil Larsh, Accident Prevention Counselor, Colfax IN (1994)
1-13. OBJECTIVE. Discuss the importance of developing accurate weight and balance calculations for both test and recreational flights. You can find additional information on weight and balance in FAA-H-8083-1A, Aircraft Weight and Balance Handbook.
a. Accuracy. A good weight and balance calculation is the keystone of flight testing. Accurately determining the aircraft’s take-off weight and ensuring that the center of gravity (CG) is within the aircraft’s design for each flight is critical to conducting a safe flight test.
b. Method. An aircraft should be level when weighed, spanwise and fore and aft using the manufacturer’s instructions, and should be in a level flight position. The FAA highly recommends you weigh the aircraft in an enclosed area, using three calibrated scales. The FAA does not recommend bathroom scales because they are not always accurate. Ensure all fuel tanks are empty.
c. A Word about Lateral Balance. Aircraft lateral balance (side to side) is often overlooked, because in most situations it is a matter of loading ballast in the form of cargo or people inside the aircraft that is placed very close to its centerline. The effects on lateral unbalance from difference in ballast weight inside the aircraft are usually minimal.
(1) Aircraft that have fuel in the wings usually have one or more fuel tanks located symmetrical from one wing to the other so lateral balance is not affected. The lateral center of gravity may become important if the fuel load is mismanaged by supplying the engine(s) unevenly from tanks on one side of the aircraft. Care should be taken when fueling the aircraft
b. To Work a CG Problem. Figure the empty weight CG first. On a piece… › (1) Under the block titled “Items,” vertically list “left wheel,”…
evenly so lateral balance is not affected on takeoff unexpectedly. Mismanagement of fuel or uneven fuel loading on aircraft with tip tanks or modified (enlarged or repositioned) fuel tanks can affect the aircraft controllability in all phases of flight.
(2) The airplane is designed so that the primary flight controls (rudder, aileron, and elevator) are streamlined with the non-movable airplane surfaces when the airplane is in a cruising straight-and-level at normal weight and loading configuration. If the airplane is flying out of that basic balanced condition, one or more of the control surfaces is going to have to be held out of its streamlined position by continuous control input. An improperly balanced airplane requires constant control pressures, produces pilot tension and fatigue, distracts the pilot from scanning, and contributes to abrupt and erratic airplane attitude control. The use of inflight adjustable trim tabs and/or autopilot systems can relieve pilot fatigue but can also mask a potential catastrophic controllability problem until it is too late to take corrective action.
(3) Caution should be exercised before undertaking any modification to the aircraft fuel system. Along with fuel flow test, proper fuel line routing, changes in performance in flight maneuvers from changes in the aircraft lateral balance need to be addressed. Phase I flight testing needs to be conducted for any modification that can change the lateral balance of the aircraft.
FIGURE 2. EMPTY WEIGHT CG
ITEMS WEIGH (LBS) ARM (INCHES) MOMENT (IN-LBS)
Left Wheel 101 60 6060
Right Wheel 99 60 5940
Tail wheel 42 180 7560
TOTALS 242 80.8 19560
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊= 𝐸𝐸𝐸𝐸𝐸𝐸𝐸𝐸𝐸𝐸 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊 𝐶𝐶𝐶𝐶
OR
19560 242 = 80.8
1-14. DETERMINING EMPTY WEIGHT CG.
a. Sample Aircraft. The sample airplane for determining empty weight is a single seater, with a design empty weight of 253 pounds and a gross weight limit of 500 pounds. The datum line is located at the nose of the aircraft and the CG range is between 69 to 74 inches from the datum.
b. To Work a CG Problem. Figure the empty weight CG first. On a piece of paper, draw four blocks. Title each block from left to right as shown in Figure 3, Takeoff CG.
(1) Under the block titled “Items,” vertically list “left wheel,” “right wheel,” and “nose/tailwheel.”
(2) Place a calibrated scale under each wheel and record the weight on each gear, in pounds, in the weight block beside the appropriate wheel.
1-15. DETERMINING TAKEOFF WEIGHT CG. › d. Loaded in this configuration, the aircraft is within the CG flight…
(3) Measure the distance in inches from the datum line, or imaginary point identified by the manufacturer (e.g., nose of the aircraft), to the centerline (C/L) of the three wheels. Record the distance of each wheel and place it in the “arm” block beside the appropriate wheel See Figure 2, Empty Weight CG.
(4) Multiply the inches (arm) by the weight on each wheel to get the moment (inch-pounds) for each wheel. Add the weight on the three gears and the three moments in inch-pounds and divide the total weight into the total moment. The sum is the “empty weight center of gravity” in inches. In the sample case, the empty weight CG is 80.8.
NOTE: All calculations should be carried out to two decimal places.
FIGURE 3. TAKEOFF CG
ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)
A/C 242 80.8 19560
Pilot 170 65 11050
Fuel 30 70 2100
TOTALS 442 74 32710
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊= 𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝐶𝐶𝐶𝐶
OR
32710 442 = 74
1-15. DETERMINING TAKEOFF WEIGHT CG.
a. Since the aircraft’s empty weight and empty weight CG are fixed numbers, the only way an aircraft’s CG can be changed is by adding weight in other locations.
b. For example, in Figure 3, the aircraft’s empty weight has been written in the appropriate blocks. The pilot weighs 170 pounds and fuel—5 gallons—weighs 30 pounds.
c. Again, all measurements are made from the datum to the centerline of the object that has been added. Weight multiplied by inches from the datum equals moment. Add the weights and moments to find the take-off CG for that particular flight.
d. Loaded in this configuration, the aircraft is within the CG flight envelope and is safe to fly.
b. In the sample problem, the previous figures for takeoff weight and… › (4) If the sample aircraft exceeded the designer’s gross weight limit,…
FIGURE 4. ADDITIONAL EQUIPMENT ADDED
ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)
A/C 242 80.8 19560
Pilot 170 65 11050
Fuel 30 70 2100
S/B 15 75 1125
Strobe 1.5 179 268.5
Fuel 1.5 55 82.5
TOTALS 460 74.3 34186
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀
𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊= 𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴 𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇𝑇 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊ℎ𝑡𝑡 𝐶𝐶𝐶𝐶
OR
34186 460 = 74.3
1-16. ADDING ADDITIONAL EQUIPMENT.
a. During flight testing, a strobe battery and handheld radio are added. The battery/battery box weight is 15 pounds and the location is 75 inches aft of the datum. The strobe assembly weight is 1.5 pounds and is located 179 inches aft of the datum. The radio’s weight is 1.5 pounds and is located 55 inches aft of the datum. See Figure 4, Additional Equipment Added.
b. In the sample problem, the previous figures for takeoff weight and moment are still accurate, hence those numbers have been listed in the appropriate blocks.
(1) Add the battery, strobe, and radio data in the appropriate locations and calculate the totals. At 465 pounds, the aircraft is still 35 pounds under its design gross weight limit of 500 pounds but is out of balance because the CG has moved 0.3 inches further aft (74.3 inches) than the allowable rear CG limit of 74 inches.
(2) Since the aircraft is out of balance with an aft CG, it is no longer 100 percent stable in pitch and would be dangerous to fly. In most cases, it is not the amount of weight added to the aircraft that can cause a major safety problem but its location.
(3) To bring this aircraft back into the safe CG range, the battery would have to be moved 9 inches forward or 66 inches from the datum line. Another alternative is to install 8 pounds of ballast in the nose, 20 inches from the datum.
(4) If the sample aircraft exceeded the designer’s gross weight limit, such as with a 300-pound pilot instead of the CG limit, its climb, stall, and performance capability would be poor and the possibility for in-flight structural failure would be high.
b. In the sample problem, the previous figures for takeoff weight and… › (6) When working a weight and balance problem with negative and…
NOTE: In the sample weight and balance, positive numbers were chosen by placing the datum line on the nose of the aircraft. Some manufacturers prefer to use a datum located somewhere between the aircraft’s nose and the leading edge of the wing.
(5) This kind of datum will set up a system of positive arms, or items located aft of the datum, and negative arms—items located forward of the datum.
(6) When working a weight and balance problem with negative and positive moments, subtract the sum of all negative moments from the sum of all positive moments to reach a “total moment” for the aircraft.
c. Checklists. In addition to the assembly/airworthiness inspection… › (4) Before takeoff;
SECTION 9. PAPERWORK
“It is harder to write a lie in a logbook than tell one, because your eyes see it and your fingers
feel it.” Bob Moorman, Ultralight Instructor (1994)
1-17. OBJECTIVE. Have the proper documentation and paperwork to conduct the flight test.
a. Weight and Balance. The weight and balance for the aircraft should be carefully done. The gross weight and CG range should be determined prior to every flight. An equipment list should be developed and maintained to identify the appliances and articles installed in the aircraft at the time of weighing for certification. It should also be kept current as installed equipment changes from additions or removals.
b. Airworthiness/Registration/Operating Limitations/Placards/Weight and Balance. Must be on board, or the aircraft is not legal for operation.
c. Checklists. In addition to the assembly/airworthiness inspection previously discussed in Chapter 1, Section 7, the builder should prepare the following checklists:
(1) Preflight;
(2) Before starting;
(3) Starting the engine;
(4) Before takeoff;
1-17. OBJECTIVE. › e. Maintenance Records (Logbooks). Operators of amateur-built aircraft…
(5) Takeoff/cruise;
(6) Descent/before landing;
(7) After landing;
(8) Securing the aircraft; and
(9) Emergency procedures.
NOTE: A checklist to cover the above procedures may seem a tedious task, but it may only be the size of a 5x8-card similar to a checklist for a Cessna 150 or a Piper Cherokee.
NOTE: The amateur builder should anticipate several revisions to the checklists.
d. Flight Manual. It is imperative that a flight manual describing the anticipated performance of the aircraft be written by the aircraft builder/kit manufacturer. The manual will be revised several times during the flight-test phase until it accurately reports the aircraft’s performance, as well as limitations, normal and emergency procedures, and descriptions of those systems installed.
e. Maintenance Records (Logbooks). Operators of amateur-built aircraft must maintain a record of the annual condition inspection in accordance with their operating limitations. The FAA recommends that owners record all inspections and maintenance performed in the aircraft’s logbooks. This will create a history of the aircraft’s maintenance and will be invaluable in spotting trends.
b. New/Newly Overhauled Engine Run-In Procedures. › (1) Most amateur-builders start with a new or newly overhauled engine…
SECTION 10. POWERPLANT TESTS
“Don’t short-change the engine tests or you won’t be around to give your grandkids a ride.”
Dick Koehler, A&P Instructor (1994)
1-18. OBJECTIVE. Ensure that the engine has been properly run-in and is safe to operate in all rpm ranges.
a. Testing. You can conduct an engine pre-oil and cold compression test as follows:
(1) Remove the rocker-box covers and one spark plug from each cylinder.
(2) Using an external oil pump, or by rotating the propeller in the direction of rotation, pump a substantial supply of oil up from the sump into the rocker arms.
(3) When the engine is pre-oiled, run a cold compression test of each cylinder.
(4) The results will serve only as an initial benchmark for comparing other compression tests taken after the engine has been run-up to operating temperature.
b. New/Newly Overhauled Engine Run-In Procedures.
(1) Most amateur-builders start with a new or newly overhauled engine and proceed to “run it in” on the airframe. This practice is followed because builders usually don’t have either a test cell or a special “club” propeller that is specifically designed to aid in engine cooling during run-in. There are pros and cons to using an airframe to run in an engine, but the best advice has always been to follow the engine manufacturer’s instructions, found either in the manufacturer’s overhaul manuals, service bulletins, or service letters. Following the manufacturer’s instructions
e. Test and Support Equipment. › (4) If there is only one CHT thermocouple, attach it to the rearmost…
is especially important if the engine has chrome cylinders which require special run-in procedures.
(2) Also, before running-up the engine, be certain that it has the proper grade oil in the sump. Some new and newly overhauled engines are shipped with a special preservative oil to prevent corrosion. Drain this out and reservice the engine with the correct oil before starting.
c. Used Engine Run-In procedures. Some amateur-builders install a used engine from a flyable aircraft. The same checks and adjustments as are performed on a new or newly-overhauled engine should be conducted on a used engine.
NOTE: Both new and used engines require special attention to engine cylinder baffling to ensure cylinder cooling is within the engine manufacturer’s CHT specifications.
d. Pre Run-In Checks.
(1) Before beginning the powerplant tests, inspect the engine and propeller carefully. All fuel and oil line connections should be tight. Check the torque on the engine mount attaching bolts. Be certain that there are no tools, hardware, or rags lying between the cylinders or under the magnetos.
(2) Check for the proper amount of oil in the engine and that the dipstick gives an accurate reading of the oil quantity. Be advised that some engines are mounted on an angle in TC’d aircraft. These engines have a special oil dipstick, which corrects for the different angle of oil in the crankcase. The same engine, mounted level in an amateur-built aircraft with the original dipstick, will not show the correct oil quantity.
e. Test and Support Equipment.
(1) A cylinder head temperature (CHT) gauge is needed to ensure that all cylinders are receiving the proper flow of cooling air.
(2) On the newer aircraft engines, the cylinders are drilled and tapped to accept a bayonet-type CHT thermocouple probes. For older engines, the thermocouple is designed like a spark plug washer and fits under a spark plug. It can be installed in any cylinder, under either the top or bottom spark plug.
(3) CHT monitors can have multiple thermocouples which may be connected to a selector switch in the cockpit, which the pilot uses to select a cylinder to monitor. This also is an excellent troubleshooting tool for identifying fouled plugs and bad ignition leads.
(4) If there is only one CHT thermocouple, attach it to the rearmost cylinder on the right side of the engine, as viewed from the cockpit, and run up the engine. Run the same test on the opposite rearmost cylinder to be certain the hottest running cylinder is monitored. You also need calibrated oil pressure and oil temperature gauges to test the accuracy of the engine instruments installed in the aircraft.
g. The First Engine Run. › (1) The first start of the engine is always a critical operation.
(5) Exhaust gas temperature (EGT) thermocouple probes, commonly known as EGTs, are becoming popular in amateur-built experimental aviation. EGTs help monitor the engine and can be an excellent way of determining which spark plug/plug wire requires attention during a magneto check and provides information on the health of the valves and cylinders. Just like CHTs, there can be one for the entire engine or one for each cylinder exhaust pipe. EGT manufacturer installation instructions and cautions should be closely followed. Accurate readings for EGTs are greatly affected by placement on the exhaust and the relation to airflow around the engine.
(6) The following support equipment is recommended:
• Fifty feet or more of tiedown rope, • Tiedown stakes, • Two chocks for each wheel, • Fire extinguisher, • Assorted hand tools, • Safety-wire, • Cotter-pins, • Ear and eye protection, • Grease pencils, • Logbooks, • Clip board, • Pen and paper, • A watch to time the tests, • Rags, and • Manufacturer’s instructions.
f. Safety Precautions. Before the first engine run, ensure the aircraft is tied down, brakes on, and the wheels are chocked. The builder and flight-test team should wear ear and eye protection. All flight-test participants should be checked out on fire extinguisher use and operation. During engine runs, do not allow anyone to stand beside the engine, or inline or close to the propeller. Making minor adjustments to a running engine, such as idle and mixture settings, is a very dangerous procedure and should be done with great care by experienced individuals.
g. The First Engine Run.
(1) The first start of the engine is always a critical operation. The engine should be pre-oiled using the manufacturer’s instructions. For aircraft using other than FAA-approved oil pressure and temperature gauges, the FAA recommends attaching an external calibrated oil temperature and pressure gauge to calibrate the engine instruments. After priming the engine and completing the starting engine checklist items, the first concern is to get an oil pressure reading within the first 20 to 30 seconds after engine start. If there is no oil pressure reading, shut down the engine.
1-18. OBJECTIVE. › i. Record the Engine Run-In Data. During the engine run, monitor the…
(2) There are three common problems that would cause low or fluctuating oil pressure.
(a) Air in the oil pressure gauge line. This is easily fixed by loosening the line connection near the oil pressure gauge and squirting oil into the line until full. Another option is to use a preoiler to provide the pressure and carefully bleed the air out of the line near the oil gauge by loosening the B-nut connecting the oil line to the gauge.
(b) A misadjusted oil pressure relief valve. Cleaning the pressure relief ball, checking for the proper number of washers, correcting spring tension, and re-adjusting the setting could solve the problem.
(c) An internal problem within the engine, most likely the oil pump. An engine tear down would be required.
(3) With good oil pressure/temperature readings and the engine running smoothly, ensure that the engine oil pressure and temperature gauges in the cockpit match the calibrated oil pressure and temperature gauges attached to the aircraft for the first run. Do not overlook this test. It is critical to determine the accuracy of the cockpit engine gauges not only for the ground engine run-in period, but also for in-flight engine cooling tests.
(4) Work through the engine manufacturer’s run-in schedule. Most engine manufacturers recommend a series of engine runs from low rpm to maximum rpm. Each run usually incorporates a 200-rpm increase and lasts no longer than 10 minutes. The secret to a successful engine run is not to let the engine temperatures exceed manufacture’s limits during engine runs.
NOTE: Engines with chrome cylinders or chrome rings require different high power run-in programs. Follow the manufacturer’s run-in instructions to ensure the engine will perform satisfactorily over its lifetime.
h. Engine Cooldown. After a ground run, the cooling off period takes approximately an hour. This is because a newly overhauled engine needs time for the internal parts, such as rings, cylinders, valves, bearings, and gear faces, to expand and contract several times to obtain a smooth surface that retains its “memory.” This is a lengthy process even when done right, but it is important not to skip any of the recommended runs. You risk increasing oil consumption and reducing overall engine performance, reliability, and engine life span -which could be costly in the long-term—if you skip any of the runs.
i. Record the Engine Run-In Data. During the engine run, monitor the CHTs, oil temperature, and oil pressure. Record the readings and adjustments for future reference. If the CHTs are rising close to the red line, reduce power and stop the test. Some causes of high CHTs include:
• Using spark plugs with the improper heat range; • CHT gauges installed on the wrong cylinder; • Missing or badly designed cylinder head cooling baffles;
k. After Shut-Down. › (3) The FAA also recommends all fuel sumps, filters, and gascolators…
• Partially plugged fuel nozzles (applicable to fuel injected engines); • Fuel lines of improper internal diameter (creates lean mixtures); • Engine improperly timed either mechanically and/or electrically; and • The carburetor fuel mixture set excessively lean.
j. Selecting Adjustments. Narrow down what adjustments need to be made by recording the change and its resulting effects. The record of the change and its effects is then used for making a logical decision for follow-on adjustments as needed to reach the proper engine performance parameters. Two ways of recording the engine performance parameters are:
(1) Keep a detailed paper log of each applicable engine instrument on each run-up.
(2) Some new Electronic Flight Instrumentation Systems (EFIS) for experimental aircraft which are either a stand-alone system or connected to a Multi-Functional Display (MFD) have the capability to record all engine performance indications for all engine runs in their entirety.
k. After Shut-Down.
(1) After each engine run, check for fuel and oil leaks, loose connections, and hot spots on cylinders, which can be indicated by burnt paint. The FAA recommends draining the oil and removing the oil screen/filter within the first 2 hours of running the engine. Check the screen/filter for ferrous metal with a magnet. Wash and inspect the screen/filter for non-ferrous metal like brass, bronze, or aluminum.
(2) A very small quantity of metal in the screen is not uncommon in a new or newly overhauled engine. It is part of the painful process of “running-in.” If subsequent oil screen checks—2 hours apart—show the engine is “making metal,” this indicates a problem inside the engine and a tear down inspection is required.
(3) The FAA also recommends all fuel sumps, filters, and gascolators should be checked for debris after each engine run. Special attention should be given to the fuel system by builders who use composite or fiberglass fuel tanks. Composite and fiberglass strands can be very fine, making visual detection difficult. Frequent cleaning of the fuel filters and screens early in the flight testing phase will avoid a gradual buildup of loose composite fibers, which would reduce or stop the flow of fuel to the engine.
a. Mixture and Idle Speed Check. After completing the initial engine… › (5) Because most air-cooled aircraft engines need excessively rich fuel…
SECTION 11. ADDITIONAL ENGINE TESTS
“Always go with the best fix not the cheapest fix.” Bill Deeth, Master Mechanic (1994)
1-19. OBJECTIVE. All of the engine and fuel system tests and inspections should be listed and recorded on a checklist designed for that purpose. That document should note the completion of each of the above tests with information obtained during that test. Record the fuel flow, compression test, magneto timing, idle speed, oil pressure, hot and cold etc. These checks will determine if the engine supply of fuel is adequate at all angles of attack.
a. Mixture and Idle Speed Check. After completing the initial engine “run-in” tests, check the idle speed and mixture settings. To determine if the mixture setting is correct, perform the following:
(1) Warm up the engine until all readings are normal.
(2) Adjust the engine rpm to the recommended idle rpm.
(3) Slowly pull the mixture control back to idle cut-off.
(4) Just before the engine quits, the engine rpm should rise about 50 rpm if the mixture is properly adjusted. If the rpm drops off without any increase in rpm, the idle mixture is set too lean. If the rpm increases more than 50 rpm, the idle mixture is set too rich.
(5) Because most air-cooled aircraft engines need excessively rich fuel air mixtures to provide cooling for full-throttle operation, the condition should be confirmed. This is most easily accomplished by running the engine at full throttle (with the aircraft properly secured), manually leaning the mixture, and observing an increase in EGTs and in some cases an actual rise in rpm.
c. Cold Cylinder Check. › (2) Probable causes of the cold cylinder problem are (1) defective…
While the amount of EGT rise is variable, the important aspect is that there is a rise of 25 to 50 degrees Fahrenheit (F) or more. This will help alleviate engine overheating situations during the first few hours of inflight operation.
NOTE: Some amateur builders, after properly setting the idle mixture/rpm to the manufacturer’s specification, increase the engine idle rpm by 100 rpm for the first 10-plus hours of flight testing. This is to ensure that the engine will not quit when the throttle is pulled back too rapidly, or when power is reduced on the final approach to landing. Be aware that in some situations, particularly with light wing loading or low drag types of aircraft, adding 100 rpm to the idle speed could cause the landing distance to be increased significantly and also have an unexpected adverse effect on landing behavior.
b. Magneto Check.
(1) The magneto checks should be smooth and the difference between both magnetos rpm drops should average about 50 rpm. The builder also should perform a “hot mag” check, to prevent unexpected engine self-starts. To perform this check, run up the aircraft until the engine is warm. At idle rpm, turn the magneto switch off, the engine should stop running. If the engine continues to run, one or both of the magnetos is not grounded, or “hot.”
(2) The usual causes for a hot magneto are a broken “P” lead coming out of the magneto or a bad magneto switch. THIS IS AN IMMEDIATE THREAT TO THE PERSONAL SAFETY OF ANYONE NEAR THE AIRPLANE AND MUST BE REPAIRED AT ONCE.
c. Cold Cylinder Check.
(1) The builder should perform a cold cylinder check if the engine is running rough and an ignition system problem could be contributing. A cold cylinder can be detected easily by switching magnetos and reading modern EGT monitors (if equipped) or by aiming a handheld laser thermometer at each exhaust stack. If you have neither one, perform the following:
(a) Run the engine on the bad magneto for about 30 seconds at 1,200 rpm. Without switching the mag switch back to “both,” shut off the engine.
(b) One of the test crew should quickly use a grease pencil to mark an area of the exhaust stacks approximately an inch from the flange that attaches the stacks to the cylinders.
(c) Check the marks on the stacks. If one or more of the exhaust stacks with a grease mark has NOT been burned to a grayish-white color and the mark on the stack still retains most of the original color of the grease pencil, the “cold cylinder” has been identified.
(2) Probable causes of the cold cylinder problem are (1) defective spark plugs, (2) ignition leads, or (3) a cracked distributor in one of the magnetos. To detect if the spark plugs are bad, switch both plugs to another cylinder. If the grease pencil proves the problem moved to the new cylinder, the spark plugs are bad. If the problem remains with the original cylinder, the ignition lead or magneto is bad.
e. Fuel Flow. A fuel flow and unusable fuel check is a field test to… › (4) The fuel consumption rate of most modern engines is about 0.55…
d. Carburetor Heat.
(1) The FAA strongly recommends that all amateur builders using a carbureted engine install a carburetor heat, or “carb heat,” system that complies with the engine manufacturer’s recommendation. If no recommendation is available, we suggest a carburetor heat system for a sea-level engine. A conventional venturi should be designed so that it will provide a 90 degrees F increase in the venturi at 75 percent power. For altitude engines using a conventional venturi carburetor, 120 degrees F increase in venturi temperature at 75 percent power will prevent or eliminate icing. Remember: Too little carburetor heat will have no effect on carburetor icing, and too much carburetor heat will cause an overly rich mixture which will reduce power and may shut down the engine.
(2) During the engine tests, make numerous checks of the carburetor heat system. To avoid overly rich mixtures from oversized carburetor heat ducts, ensure that the carburetor heat duct is the same size as the inlet of the carburetor.
(3) Be certain there is a positive reduction in rpm each time “carb heat” is applied. If there is no reduction, or the rpm drop is less than expected, check the carb heat control in the cockpit and on the carb heat air box for full travel. Also, check for air leaks in the “scat tube” connecting the heat muff to the carburetor air box.
e. Fuel Flow. A fuel flow and unusable fuel check is a field test to ensure the aircraft engine will get enough fuel to run properly, even if the aircraft is in a steep climb or stall attitude, and is accomplished by:
(1) Place the aircraft’s nose at an angle 5 degrees above the highest anticipated climb angle. The easiest and safest way to do this with a conventional gear aircraft is to dig a hole and place the aircraft’s tail in it. For a nose gear aircraft, build a ramp to raise the nose gear to the proper angle.
(2) Make sure the aircraft is tied-down and chocked. With minimum fuel in the tanks, disconnect the fuel line to the carburetor. The fuel flow with a gravity flow system should be 150 percent of the fuel consumption of the engine at full throttle. With a fuel system that is pressurized, the fuel flow should be at least 125 percent. When the fuel stops flowing, the remaining fuel is the “unusable fuel” quantity.
(3) The formula for fuel flow rate for a gravity-feed fuel system is 0.55 times engine horsepower (HP) times 1.50. This gives a fuel flow rate in pounds of fuel per hour. Divide the pounds-per-hour number by 60 to calculate pounds per minute, and divide again by 6 to calculate gallons per minute. To get gallons per hour for Avgas divide pounds per hour by 6; or multiple gallons per minute by 60. For a pressurized system, substitute 1.25 for 1.50 to calculate the fuel flow rate.
(4) The fuel consumption rate of most modern engines is about 0.55 pounds per hour per brake HP. The chart below illustrates the results of this calculation for a 100 HP engine:
1-19. OBJECTIVE. › h. Last Check. Drain the oil and replace the oil filter, if applicable.…
FIGURE 5. 100 HP FUEL FLOW RATE CHART
If your fuel is… Then the fuel flow rate for a 100 HP engine is…
Pounds per hour Pounds per minute Gallons per hour
Gravity feed 82.5 1.38* 13.75
Pressurized 68.75 1.15* 11.49*
*-rounded to the nearest 100th.
f. Changing Fuel Flow or Pressure. If the aircraft’s fuel flow rate is less than planned, there is a volume or pressure problem. An increase in the fuel flow volume may necessitate installation of larger fuel line fittings on the fuel tanks, fuel selector, and carburetor in addition to larger internal diameter fuel lines. To increase fuel pressure, install an electrically driven or engine-driven mechanical fuel pump prior to the first flight.
g. Compression Check. When the engine run-in procedures have been completed, perform an additional differential compression check on the engine and record the findings. If a cylinder has less than 60/80 reading on the differential test gauges on a hot engine, that cylinder is suspect. Have someone hold the propeller at the weak cylinder’s top dead center and with compressed air applied, listen. If air is heard coming out of the exhaust pipe, the exhaust valve is not seating properly. If air is heard coming out of the air cleaner/carb heat air box, the intake valve is bad. When the oil dipstick is removed and air rushes out, the piston rings are the problem.
h. Last Check. Drain the oil and replace the oil filter, if applicable. Check the oil and screens for metal, visually inspect the engine, and do a run-up in preparation for the taxi tests. Do not fly the aircraft if anything is wrong, no matter how small or how insignificant. The sky, like the sea, is an unforgiving and uncompromising environment.
1-21. RECOMMENDATIONS FOR ALL PROPELLERS. › a. Never approach the vicinity of the propeller unless the ignition…
SECTION 12. PROPELLER INSPECTION
“A tough decision is what a man makes when he cannot form a committee to share the blame”
George Lutz, Col. U.S. Air Force, Retired (1994)
1-20. OBJECTIVE. Help you develop an inspection program to maintain your propeller.
a. Propeller Designs. There are three kinds of propeller designs: metal, wood, and composite. Because of weight considerations, metal propellers are used more on amateur-built aircraft than ultralight aircraft. Wood and composite propellers are the overwhelming choice for ultralight aircraft. Wood propellers are light, reliable, and inexpensive but require frequent inspections. Composite carbon-graphite material props are more expensive than wood, but are stronger and require less maintenance.
b. Choosing a Propeller. All types of propellers have one thing in common: they are constantly under high levels of vibration, torque, thrust, bending loads, and rotational stress. Even small nicks in the leading edge of the blade can very quickly lead to a crack, followed by blade separation. Propeller tip failure and a subsequent violent, out of balance situation can cause the propeller, engine, and its mounts to be pulled from the airframe in less than 5 seconds. Choose your make and model of propeller carefully. A propeller with the wrong size and pitch will give a poor rate of climb, cruise, or could cause the engine to “overspeed.” Always follow the manufacturer’s recommendations.
1-21. RECOMMENDATIONS FOR ALL PROPELLERS.
a. Never approach the vicinity of the propeller unless the ignition switches have been confirmed to be in the OFF position and the key is removed.
1-21. RECOMMENDATIONS FOR ALL PROPELLERS. › n. After torqueing the propeller, track the blades.
b. Never use a propeller for a tow bar when moving the aircraft.
c. Never stand in front of or in-line of a rotating propeller.
d. Never hand prop an engine on uneven or wet/snow covered ground.
e. Always inspect the propeller before and after a flight.
f. When working on a propeller, make sure the ignition is off first.
g. Always maintain the propeller to manufacturer’s instructions.
h. To avoid nicks and cuts, do not perform run-ups near gravel or loose stones.
i. Apply a coat of automotive wax once a month to protect the finish and keep out moisture.
j. Assume a propeller is unairworthy if it has suffered any kind of impact or ground strike.
k. After any repair or repainting, or if vibration or roughness is noted, re-balance the propeller.
l. Propeller blades should be balanced within 1 gram of each other to avoid over stressing the gear reduction system and propeller shaft.
m. Check the bolt torque on all newly installed propellers every hour of operation for the first 10 hours and once every 5 hours thereafter.
n. After torqueing the propeller, track the blades.
FIGURE 6. PROPELLER TRACKING
+/- 1/16
1-22. PROPELLER TRACKING CHECK.
a. Installation. Ensuring good powerplant operation starts with a properly installed propeller. You should check the propeller for proper tracking—the blades rotating in the same plane of rotation. The following procedure is simple and takes less than 30 minutes:
a. Identifying Corrosion. › (4) If any of these signs of corrosion are found, do NOT fly the…
(1) Chock the aircraft so it cannot be moved. Remove one sparkplug from each cylinder—this will make the propeller easier and safer to turn.
(2) Rotate the blade so it is pointing straight down.
(3) Place a solid object (e.g., a heavy wooden block that is at least a couple of inches higher off the ground than the distance between the propeller tip and the ground) next to the propeller tip so it just touches.
(4) Rotate the propeller slowly to see if the next blade “tracks” through the same point (touches the block, see Figure 6). Each blade should be within 1⁄16-inch from one another.
b. Tracking. If the propeller is out of track, one or more propeller blades may be bent, a propeller flange may be bent, or propeller mounting bolts that are over or under torqued. An out-of-track propeller will cause vibration and stress to the engine and airframe and may cause premature propeller failure.
1-23. METAL PROPELLER INSPECTION. Perhaps the two biggest problems affecting the airworthiness of metal propellers are corrosion and nicks on the leading edge.
a. Identifying Corrosion.
(1) Surface corrosion can occur on the surface of metal blades due to a chemical or electrochemical action. The oxidation product usually appears on the surface of the metal as a white powder.
(2) Pitting corrosion causes small cavities or pits extending into the metal surface. This is an advanced form of corrosion, appearing as small dark holes that usually form under decals or blade overlays.
(3) Intergranular corrosion, rare and difficult to detect in propellers, is the most dangerous form of corrosion. It attacks the boundary layers of the metal, creating patches of lifted metal and white/gray exfoliation on the surface of the propeller. It is sometimes found in propellers that had a ground strike and have been straightened.
(4) If any of these signs of corrosion are found, do NOT fly the aircraft. Refer to the manufacturer’s maintenance manual for corrosion limits and repairs or the current editions of AC 43-4, Corrosion Control for Aircraft, and AC 20-37, Aircraft Propeller Maintenance, for additional maintenance information and corrective actions.
b. Torque Check. You should check for proper torque on the mounting… › (1) After 10 hours, check the bolt torque every 5 hours of operation.
b. Nicks and Metal Blades.
(1) Nicks in the leading and trailing edge of a metal blade are usually V-shaped. They are caused by high-speed impact between the propeller and a stone or piece of gravel. Properly trained individuals can “dress out” the nick or pit if the nick is not too wide and/or deep. Before each nick is dressed out, each nick and surrounding area should be inspected with a 10-power magnifying glass for cracks. If an area looks suspicious, inspect the area again using the propeller manufacturer’s approved dye penetrant or fluorescent penetrant method.
(2) If the nick is left unattended, the high propeller operational stresses will be concentrated at the bottom of the nick’s V and, in time, will generate a crack. The crack can migrate across the blade until the blade fails, producing a massive imbalance between the propeller and the engine, ultimately causing structural failure. Cracks in metal blades cannot be repaired. A cracked propeller must be marked unserviceable and discarded.
WARNING. Metal propellers are matched/tuned to the engine and airframe resonant frequency by being manufactured with a particular diameter to minimize vibration. DO NOT SHORTEN METAL BLADES for any reason unless the manufacturer specifically permits this major alteration.
1-24. WOOD PROPELLER INSPECTION.
a. Inspection Frequency. Wood propellers should be inspected before and immediately after a flight. Inspect to ensure the following:
(1) The drain holes are open on metal edged blade tips.
(2) The metal/composite leading edge is secured and serviceable.
(3) The blades, hub, and leading edge have no scars or bruises.
(4) The mounting bolt torque and safety wire or cotter pins are secure.
(5) There are no cracks on the propeller spinner (if applicable), and the safety wire is secure.
(6) There are no small cracks in the protective coating on the propeller. Ultraviolet radiation can cause these cracks.
(7) There is any charring around either the mating surface of the prop and engine flange. Charring in either location indicates a loose propeller.
b. Torque Check. You should check for proper torque on the mounting bolts of a new, wooden propeller within the first hour of flight and every hour for 10 operational hours thereafter.
(1) After 10 hours, check the bolt torque every 5 hours of operation. You should also check the mounting bolt torque before flight if the aircraft has been in storage for 3 to 6 months.
1-25. COMPOSITE PROPELLER INSPECTION. › b. Carbon/Graphite. The carbon/graphite composite propellers are…
(2) If you need to torque the bolts, we suggest that all the bolts be loosened for an hour to allow the wood to relax. “Finger tighten” the bolts until snug and tighten the attaching bolts in small increments, moving diagonally across the bolt circle. It is good practice to check the propeller track (see Chapter 1, Section 7) as the bolts are torqued down. The torqued bolts should be safety wired in pairs.
(3) If nylon/fiber insert type nuts are used, you should change them every time you re-torque the propeller bolts. Never match this type of nut to a bolt with a cotter key hole in its threaded area—the sharp edges around the hole will cut the nylon/fiber insert and reduce the fastener’s effectiveness. All self-locking nuts should have at least two bolt threads visible past the nylon/fiber insert after torqueing.
c. Wood Propeller Repairs. You should remove a wood propeller from an aircraft and send it back to the manufacturer for repair, if any of the following damage is found:
(1) Any cracks in the blades or hub;
(2) Deep cuts across the wood grain;
(3) Blade track that exceeds 1⁄16-inch limits after attempts to repair;
(4) Any warpage or obvious defect;
(5) Extreme wear such as leading edge erosion or bolt hole elongation; and
(6) Any separation between lamination.
NOTE: When parking the aircraft, always leave the wood propeller in the horizontal position. This position will allow the wood to absorb small amounts of moisture evenly across its entire span rather than concentrating the moisture (weight) in the low blade and creating a vibration problem.
1-25. COMPOSITE PROPELLER INSPECTION. There are generally two types of composite propellers: thermo-plastic injection molded propeller and the carbon/graphite fiber composite propeller.
a. Thermoplastic. The thermoplastic injection-molded propeller is a low cost, thin bladed propeller used on engines of 80 HP or less. Propeller inspection is straightforward: examine blades and hub for cracks and nicks. If a crack is found, do not fly until the propeller is replaced. Small nicks of 3⁄16-inch or less can be dressed out and filled with a two-part epoxy.
b. Carbon/Graphite. The carbon/graphite composite propellers are generally used on engines of 40 HP and more. You should look for hairline cracks in the gel coat. Spider cracks are usually caused by vibration generated by a mismatch of the engine and propeller combination. If you find a crack in the base material of the propeller—other than the gel coat—do not fly until the manufacturer inspects the propeller.
b. Carbon/Graphite. The carbon/graphite composite propellers are… › (2) Before making even small repairs on a composite propeller, check…
(1) Nicks of ½-inch or less in the leading or trailing edges of carbon/graphite propellers can be dressed out and filled using a two-part epoxy. But if the nick has severed the fiberglass roving—which looks like a fiberglass wire bundle—that runs hub to tip on the leading and trailing edge, do not fly. The propeller has severe damage and must be sent back to the factory for inspection and repair.
(2) Before making even small repairs on a composite propeller, check with the manufacturer.
2-2. TAXI TESTS. › a. Preparation. Before taxi tests in a conventional, or tailwheel,…
CHAPTER 2. TAXI TESTS
SECTION 1. LOW-SPEED TAXI TESTS
“Yelling ’Clear the Prop!’ before you start an aircraft is the first of a series
of well planned, choreographed steps to make you a professional.”
Jack Crawford, Pilot, Mechanic, Airport Operator (1994)
2-1. OBJECTIVES. Ensure that the aircraft “tracks” straight and there is adequate directional control at 20 percent below the anticipated take-off speed. Determine if the aircraft’s engine cooling and the brake system are adequate. Predict the flight trim of the aircraft and its handling characteristics during takeoff and landings. Enable the pilot to become proficient with the handling and braking characteristics of the aircraft.
NOTE: You should conduct a low- or high-speed taxi test as if it were the first flight. The pilot should be wearing the proper clothing, seat belt/shoulder harness, and helmet and be mentally and physically prepared for the possibility of flight.
2-2. TAXI TESTS.
a. Preparation. Before taxi tests in a conventional, or tailwheel, aircraft, the tail should be physically raised until the aircraft is just about in the takeoff position. The pilot should spend an hour or more in the cockpit to become accustomed to the aircraft’s takeoff position. This small but important aspect of training will help the pilot avoid overreacting to an unexpected deck angle on the first flight. Now is the time for the pilot at the controls to have identified all the controls and devices necessary to fly the aircraft. The checklist should be in an advanced state of development, the seating and seat belts must be fully fitted, and the seat height position must be established. Seating the pilot too low is a major problem in properly identifying pitch altitude during operation.
2-3. OBJECTIVE. › c. Increasing Taxi Speed. Each taxi run should be 5 mph faster than the…
NOTE: A minimum of one other flight-test team member should always be monitoring taxi tests. This team member can watch for evidence of fire/smoke or other problems the pilot can’t see.
b. Beginning the Test. The taxi tests should begin with a taxi speed no faster than a walk. The pilot should spend this time getting acquainted with the aircraft’s low speed handling characteristics by practicing 90-, 180-, and 360-degree turns and braking action. The pilot should also remember the importance of monitoring the oil pressure, oil temperature, CHT, and maintaining them within limits, and must not overlook these checks.
NOTE: Some aircraft brake manufacturers have specific brake lining conditioning procedures (break-in) for metallic and nonasbestos organic linings. You should complete proper brake lining conditioning before starting the low and high-speed taxi tests. If not properly conditioned, the brake lining will wear quickly and give poor braking action at higher speeds.
c. Instrument Check. The pilot should check the flight instruments for operation each time the pilot taxies the aircraft. The compass should match the direction in which the aircraft is pointed, such as the magnetic heading of the runway or taxi way. When making a right hand turn, the turn coordinator/turn and bank should indicate a right hand turn but the ball should skid to the left. The vertical speed indicator should read zero and the artificial horizon should indicate level.
d. After Taxi Run. After each taxi run, inspect the aircraft for oil and brake fluid leaks. You should not consider a leak as a minor problem, but repair every leak and service the system before the next taxi test
SECTION 2. HIGH-SPEED TAXI TESTS
“First get used to the fact that you are now 30 feet wide
and you steer with your feet.” Wayne Nutsch
2-3. OBJECTIVE. Determine the aircraft’s high-speed handling and braking parameters.
a. Direction of Rotation. Propeller rotation will determine which rudder pedal you press to compensate for the asymmetrical thrust of the propeller blades. For example, when viewed from the cockpit, a Volkswagen automotive engine mounted in a tractor configuration will rotate the propeller counterclockwise. In this case, the pilot must use the left rudder pedal for high-speed taxi and takeoff. For a propeller turning clockwise, you would apply right rudder pedal.
b. Follow the Flight-Test Plan. As with every part of the flight testing program, the high-speed taxi tests should follow the flight-test plan. Start slowly and do not progress to the next step until the flight-test team is thoroughly satisfied with the aircraft and the team’s performance.
c. Increasing Taxi Speed. Each taxi run should be 5 mph faster than the last run until the aircraft is within 80 percent of the predicted stall speed. Prior to reaching the predicted stall
2-3. OBJECTIVE. › g. Repairs. During this inspection, you must fix all discrepancies.…
speed, the pilot should test aileron effectiveness by attempting to rock the wings slightly. As taxi speeds increase, the rudder becomes more responsive and directional control will improve.
(1) In a nose gear aircraft, the pilot should be able to raise the nose of the aircraft at 80 percent of the predicted stall speed. If the nose cannot be raised at this speed, the weight and balance and CG range should be rechecked. Most likely, there is a forward CG problem or the main gear is too far aft.
(2) In a tailwheel aircraft at 80 percent of stall speed, the pilot should be able to lift the tail and assume a takeoff position. Again, if the tail cannot be raised, recheck the weight and balance and CG range. Most likely, there is a rearward CG problem or the main gear is too far forward.
CAUTION: Heavy braking action at high speeds in tailwheel aircraft may cause directional problems, such as ground loops or nose overs.
d. Taxi with Flaps. If runway conditions permit, duplicate each taxi test with the flaps in the takeoff and landing configuration. Record the flap effects on directional control and insert the information in the draft copy of the aircraft’s flight manual.
e. Lift-Off Point. Estimate the point on the runway where lift-off will occur and mark it with a green flag if no other existing reference is available.
f. Braking Distance.
(1) Determine how much runway the pilot will need if it becomes necessary to abort the takeoff. This is usually accomplished by accelerating to 80 percent of lift off speed, bringing the engine back to idle, and applying heavy braking action to bring the aircraft to a full stop. After a takeoff/abort test, give the brakes time to cool down. The brake lining must be examined carefully and replaced if necessary.
(2) After determining the distance required to come to a full stop after aborting, add 30 percent to the distance. Measure that distance from the opposite end of the active runway. If no existing reference is available, mark it with a red flag. The taxi tests are completed when the test pilot is satisfied with both the aircraft’s and the test pilot’s individual performance. Before the first flight, you should thoroughly inspect the aircraft and give special attention to the landing gear, brake system, engine, and propeller.
g. Repairs. During this inspection, you must fix all discrepancies. Examine the screens/filters for metal, flush the fuel system, and clean all the screens/filters. Perform a leak check on the engine and the fuel system by running-up the engine.
NOTE: The first high-speed taxi tests should be made in a no wind or a light head wind condition. The pilot should ensure that the tests will not interfere with the normal airport operations or create a safety hazard for other aircraft.
NOTE: Pilots of tailwheel aircraft must always be aware that ground loops are possible at any speed. This is true especially if the main landing gear is located too far forward of the aircraft’s CG.
CHAPTER 3. THE FIRST FLIGHT
“It is critically important that a test pilot never succumb to the temptation to do too much too soon, for that path leads but to the grave.”
3-3. RECOMMENDATIONS. › a. The best time to test fly an aircraft is usually in the early…
Richard Hallion (1987)
SECTION 1. GENERAL
3-1. OBJECTIVE. Take every precaution to ensure that the first test flight is an uneventful one.
3-2. GENERAL.
a. The first flight is an important event for you. As important as it is, it should not be turned into a social occasion. This puts enormous peer pressure on the pilot to fly an aircraft that may not be airworthy or to conduct the flight in inclement weather.
b. A professional will avoid this trap by following the flight-test plan and inviting only those members of the crew needed to perform specialized tasks when testing the aircraft.
c. The first flight should be flown a thousand times: the first 500 on paper, the next 499 flights in the test pilot’s mind, and once in actuality. The first flight test should be so well-rehearsed by the test pilot and ground crew that the first flight is a non-event.
3-3. RECOMMENDATIONS.
a. The best time to test fly an aircraft is usually in the early morning when the winds are calm, and the pilot is well rested.
(11) The airspeed indicator is marked with sticky tape or set… › (c) Maneuvering speed (Va) = 2 times the aircraft’s predicted stall…
b. In addition to a pilot’s kneeboard, a small portable tape recorder or video camera properly mounted to the aircraft is an excellent way to record data.
c. Good communication with the ground is essential for data exchange and safety.
3-4. FIRST FLIGHT INSPECTION. Before the first flight, the test pilot and at least one other experienced person should give the aircraft a good pre-flight inspection. As part of a thorough aircraft pre-flight inspection, check that:
a. Fuel, Weight and Balance, and Fluids.
(1) The fuel on board is four times the amount of usable, clean, and proper octane fuel than is needed for the first flight. If the aircraft has a 2-cycle engine, check that the oil-to-fuel ratio is correct.
(2) A current weight and balance check is completed. The aircraft’s CG should be in the forward half of the safe CG range. This will reduce the possibility of instability during approach to a stall and enhance recovery from one.
(3) Check oil, brake fluid, and hydraulic system for the correct fluid and quantity.
Continue reading ↓ 120 of 286 passages shown