Radar Vectors
Advisory Circular Cancelled Issued Dec 22, 2003 AIR-130 70 pages Copy saved Nov 18, 2026

AC 20-138A Airworthiness Approval of Global Navigation Satellite System (GNSS) Equipment

Establishes an acceptable means, but not the only means, of obtaining airworthiness approval of Global Positioning System (GPS) equipment for use as a supplemental navigation system for oceanic and remote domestic en route, terminal, and non-precision instrument approach (except localizer directional aid (LDA) and simplified directional facility (SDF) operations.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

AC-20-138A

AIRWORTHINESS APPROVAL OF GLOBAL

NAVIGATION SATELLITE SYSTEM (GNSS)

EQUIPMENT

December 22, 2003

TABLE OF CONTENTS Paragraph Page

1. Purpose … 1 2. Cancellation … 1 3. Related Federal Aviation Regulations … 1 4. How to Use this Document … 1 5. Definitions … 1 6. Related Reading Materials … 3 7. Background … 6 8. Approval Process … 9 9. GNSS Equipment Limited to VFR Use … 12 10. TSO Authorizations … 13 11. Equipment Performance – GPS Antenna … 15 12. Equipment Performance – GNSS Sensor … 17 13. Equipment Performance – Stand Alone Navigation Equipment … 20 14. Equipment Performance – LAAS VDB Receiver … 24 15. Installation Issues – General … 24 16. Installation Issues – GPS Antenna … 25 17. Installation Issues – GNSS Sensor … 26 18. Installation Issues – Stand Alone Navigation Equipment … 28 19. Installation Issues – LPV and GLS Approaches … 33 20. Installation Issues – LAAS VDB Receiver … 34 21. Data Submittal … 35 22. Ground Test … 36 23. Flight Test … 38 APPENDIX 1: GPS Oceanic/Remote Navigation (3 pages) APPENDIX 2: Integration of GLONASS with GPS or GPS/WAAS (4 pages) APPENDIX 3: Example Format for a Quick Reference Guide (8 pages) APPENDIX 4: Sample Airplane/Rotorcraft Flight Manual Supplement (5 pages) APPENDIX 5: Installation of En Route GPS Equipment For VFR Use Only (2 pages)

Page i (and ii)

1. PURPOSE. This advisory circular (AC) provides guidance material for the airworthiness approval of Global Navigation Satellite System (GNSS) equipment. Like all AC material, this AC is not mandatory and does not constitute a regulation. It is issued for guidance purposes and to outline a method of compliance with the rules. In lieu of following this method without deviation, the applicant may elect to follow an alternate method, provided the alternate method is also found by the Federal Aviation Administration (FAA) to be an acceptable means of complying with the requirements of the federal aviation regulations (Title 14 of the Code of Federal Regulations, 14 CFR). This AC addresses the following equipment:

DEFINITIONS. › GLONASS. GLONASS is a Russian satellite based radio navigat

a. GNSS sensors, including those incorporating Wide Area Augmentation System (WAAS), Local Area Augmentation System (LAAS), or the Russian Global Navigation Satellite System (GLONASS).

b. GNSS stand-alone navigation equipment that provides deviations (steering commands) for en route, terminal, or approach operations (including Category I precision approach).

2. CANCELLATION.

a. AC 20-138, Airworthiness Approval of Global Positioning System (GPS) Navigation Equipment for Use as a VFR and IFR Supplemental Navigation System, dated May 25, 1994, is canceled.

3. RELATED FEDERAL AVIATION REGULATIONS. 14 CFR Parts 21, 23, 25, 27, 29, 43, 91, 121, and 135.

4. HOW TO USE THIS DOCUMENT. This document is organized into general categories of equipment and installations. Paragraph 8 summarizes the approval process and applies to all projects. Paragraph 9 applies to GNSS as an aid to visual flight rules (VFR) navigation, while paragraphs 10 through 23 address instrument flight rules (IFR) navigation. Guidance concerning the equipment performance and functions is provided in paragraphs 11 through 14, and installation guidance is provided in paragraphs 15 through 20. Paragraphs 21 through 23 provide additional information on the data submittal, ground test and flight test as they apply to an installation approval.

5. DEFINITIONS.

a. Aircraft-Based Augmentation System (ABAS). An augmentation system that augments and/or integrates the information obtained from the other GNSS elements with information available on board the aircraft.

b. Ground-Based Augmentation System (GBAS). An augmentation system in which the user receives augmentation information directly from a ground-based transmitter.

c. GLONASS. GLONASS is a Russian satellite based radio navigation system, which provides a positioning service anywhere in the world. Until the FAA declares GLONASS fully operational for U.S. aviation, its use is limited to a supplement to GPS navigation. The FAA will declare GLONASS fully operational after the system

DEFINITIONS. › Special Category I (SCAT-I). In order to expedite the imple

management and maintenance are mature. The following capabilities are expected before the FAA will declare GLONASS operational for U.S. aviation:

(1) Mature maintenance practices;

(2) Commitment to maintain a complete constellation of satellites; and

(3) Issuance of international NOTAMs prior to any scheduled maintenance, and after the onset of any unscheduled outages.

d. Global Navigation Satellite System (GNSS). The GNSS is a generic term for satellite-based navigation, including GPS, SBAS, GBAS, GLONASS, and any other satellite navigation system.

e. GNSS Landing System (GLS). A satellite-based navigation system that provides precision approach (including SBAS/WAAS and GBAS/LAAS).

f. Global Positioning System (GPS). GPS is a U.S. satellite based radio navigation system that provides a precise positioning service anywhere in the world. The service provided by GPS for civil use is defined in the GPS Standard Positioning System Signal Specification.

g. Local Area Augmentation System (LAAS). LAAS is the GBAS provided by the FAA.

h. Navigation. Within the context of this AC, navigation refers to any function used to direct the course of an aircraft. A navigation system as addressed in this AC provides the functions of position estimation, path definition, path steering, and situation indications and alerting to the flight crew.

i. Receiver Autonomous Integrity Monitoring (RAIM). According to TSO-C129 (all revisions (AR)), any algorithm which verifies the integrity of the position output using GPS measurements, or GPS measurements and barometric aiding, is considered a RAIM algorithm. An algorithm which uses additional information (e.g., multi-sensor system) to verify the integrity of the position output may be acceptable as a RAIMequivalent. Within this AC, the term RAIM is a synonym for ABAS and is used to refer to both RAIM or RAIM-equivalent algorithms.

j. Satellite-Based Augmentation System (SBAS). A wide coverage augmentation system in which the user receives augmentation information from a satellite-based transmitter.

k. Special Category I (SCAT-I). In order to expedite the implementation of satellite-based navigation, the aeronautical industry and the FAA in 1993 developed RTCA/DO-217, Minimum Aviation System Performance Standards (MASPS) DGNSS Instrument Approach System: Special Category I. The FAA adopted this standard in Order 8400.11, IFR Approval for Differential Global Positioning System Special Category I Instrument Approaches Using Private Ground Facilities. The intent of SCAT-I is the same as LAAS, except it is limited to Category I precision approach and does not ensure interoperability between different vendors. SCAT-I allows private facilities to be fielded before all of the issues associated with a public system are

FAA Advisory Circulars. The following documents may be obtai › AC 20-115B, Radio Technical Commission for Aeronautics, Inc.

resolved. With the adoption of ICAO standards for LAAS in 2001, the SCAT-I standards became obsolete and should no longer be used.

l. Stand-alone. Stand-alone as addressed in this AC refers to navigation equipment incorporating the GPS or GPS/WAAS position sensor and a navigation function, so that the equipment provides path deviations relative to a selected path.

m. Wide Area Augmentation System (WAAS). WAAS is the SBAS provided by the FAA.

6. RELATED READING MATERIALS.

a. FAA Orders and Technical Standard Orders (TSO). The following documents may be obtained from the Department of Transportation, FAA, Aircraft Certification Service, Aircraft Engineering Division, AIR-130, 800 Independence Avenue, SW., Washington, D.C. 20591, or on the FAA Internet at http://av-info.faa.gov/tso/.

(1) TSO-C115b, Airborne Area Navigation Equipment Using Multi-Sensor Inputs;

(2) TSO-C129a, Airborne Supplemental Navigation Equipment Using the Global Positioning System (GPS);

(3) TSO-C144, Airborne Global Positioning System Antenna;

(4) TSO-C145a, Airborne Navigation Sensors Using the Global Positioning System (GPS) Augmented by the Wide Area Augmentation System (WAAS);

(5) TSO-C146a, Stand-Alone Airborne Navigation Equipment Using the Global Positioning System (GPS) Augmented by the Wide Area Augmentation System (WAAS);

(6) TSO-C161, Local Area Augmentation System Positioning and Navigation Equipment;

(7) TSO-C162, Local Area Augmentation System Very High Frequency Data Broadcast Equipment;

(8) Order 8400.11, IFR Approval of Differential GPS Special Category I Instrument Approaches Using Private Ground Facilities; and

(9) Order 8400.12A, Required Navigation Performance 10 (RNP-10) Operational Approval.

b. FAA Advisory Circulars. The following documents may be obtained from the Department of Transportation, Subsequent Distribution Office, SVC-121.23, Ardmore East Business Center, 3341 Q 75th Ave, Landover, MD 20785. The Advisory Circular Checklist (AC 00-2) is available at http://www.faa.gov. The advisory circular checklist contains status and order information for the FAA advisory circulars.

(1) AC 20-115B, Radio Technical Commission for Aeronautics, Inc. Document RTCA/DO-178B;

(2) AC 20-129, Airworthiness Approval of Vertical Navigation (VNAV) Systems for Use in the U.S. National Airspace System (NAS) and Alaska;

(3) AC 20-130A, Airworthiness Approval of Navigation or Flight Management Systems Integrating Multiple Navigation Sensors;

FAA Advisory Circulars. The following documents may be obtai › AC 120-33, Operational Approval of Airborne Long-Range Navig

(4) AC 21-40, Application Guide for Obtaining a Supplemental Type Certificate;

(5) AC 23-17A, Systems and Equipment Guide for Certification of Part 23 Airplanes;

(6) AC 23-1309-1C, Equipment, Systems, and Installations in Part 23 Airplanes;

(7) AC 23.1419-2A, Certification of Part 23 Aircraft for Flight in Icing Conditions;

(8) AC 25-1309-1A, System Design and Analysis;

(9) AC 25.1329-1A, Automatic Pilot Systems Approval;

(10) AC 25.1419-1, Certification of Part 25 Aircraft for Flight in Icing Conditions;

(11) AC 43.13-1B, Acceptable Methods, Techniques and Practices – Aircraft Inspection and Repair;

(12) AC 43-13-2A, Acceptable Methods, Techniques and Practices – Aircraft Alterations;

(13) AC 90-79, Recommended Practices and Procedures for the Use of Electronic Long-Range Navigation Equipment;

(14) AC 90-94, Guidelines for Using GPS Equipment for IFR En Route and Terminal Operations & for Nonprecision Instrument Approaches;

(15) AC 90-96, Approval of U.S. Operators and Aircraft to Operate under Instrument Flight Rules (IFR) in European Airspace Designated for Basic Area Navigation (BRNAV/RNP-5);

(16) AC 91-49, General Aviation Procedures for Flight in North Atlantic Minimum Navigation Performance Specification Airspace;

(17) AC 120-29A, Criteria for Approving Category I and Category II Landing Minima for FAR 121 Operators. This AC supplements Appendix 2 of AC 120-29A with respect to the installation of GPS/WAAS Category I equipment;

(18) AC 120-33, Operational Approval of Airborne Long-Range Navigation Systems for Flight within the North Atlantic Minimum Navigation Performance Specification Airspace.

RELATED READING MATERIALS. › National Imagery and Mapping Agency (NIMA) Technical Report

c. RTCA, Inc. documents. The following documents may be purchased from RTCA, Inc., 1828 L Street, NW, Suite 805, Washington, DC 20036, or purchased on-line at http://www.rtca.org/.

(1) RTCA/DO-160D, Environmental Conditions and Test Procedures for Airborne Equipment;

(2) RTCA/DO-178B, Software Considerations in Airborne Systems and Equipment Certification;

(3) RTCA/DO-200A, Standards for Processing Aeronautical Data;

(4) RTCA/DO-201A, Standards for Aeronautical Information;

(5) RTCA/DO-208, Minimum Operational Performance Standards for Airborne Supplemental Navigation Equipment Using Global Positioning System (GPS);

(6) RTCA/DO-228 with Change 1, Minimum Operational Performance Standards For Global Navigation Satellite System (GNSS) Airborne Antenna Equipment;

(7) RTCA/DO-229C, Minimum Operational Performance Standards for Airborne GPS/WAAS Equipment;

(8) RTCA/DO-236A, Minimum Aviation System Performance Standards: Required Navigation Performance for Area Navigation;

(9) RTCA/DO-246B, GNSS Based Precision Approach Local Area Augmentation System (LAAS) Signal-in-Space Interface Control Document (ICD);

(10) RTCA/DO-253A, Minimum Operational Performance Standards for GPS Local Area Augmentation System Airborne Equipment;

(11) RTCA/DO-257A, Minimum Operational Performance Standards for the Depiction of Navigation Information on Electronic Maps.

d. The FAA and Industry Guide to Avionics Approvals, April 13, 2001. Copies of this document may be obtained at http://www1.faa.gov/certification/aircraft/avionics_approvals_guide.htm.

e. GPS Standard Positioning Service Performance Standard, October, 2001. Copies of this document and general information related to GPS may be requested at http://www.navcen.uscg.gov/.

f. Department of Defense Interface Control Document (ICD) ICD-GPS-200C, Navstar GPS Space Segment/Navigation User Interface. Copies of this document may be requested from the GPS Joint Program Office, SSD/CZ, Los Angeles AFB, CA 90006. Alternatively, copies of this document may be requested at http://www.navcen.uscg.gov/.

g. National Imagery and Mapping Agency (NIMA) Technical Report NIMA TR 8350.2, World Geodetic System 1984, Its Definition and Relationships with Local Geodetic Systems. Copies of this document may be requested at http://www.nima.mil/.

h. FAA National Airspace System Architecture Version 4.0. An electronic version of this document and architecture updates is available at http://www.faa.gov/nasarchitecture/.

Global Positioning System (GPS). › Receiver Autonomous Integrity Monitoring (RAIM). When GNSS

i. FAA Specification Wide Area Augmentation System (WAAS), FAA-E-2892B. This document is available on-line at http://www2.faa.gov/asd/international/GUIDANCE_MATL/2892b_c1.pdf.

j. DOD/DOT 2001Federal Radionavigation Plan (FRP). The FRP is published every two years in which copies may be ordered through the National Technical Information Service, Springfield, VA 22161; internet: http://www.ntis.gov/.

k. DOD/DOT 2001 Federal Radionavigation Systems (FRS). The FRS is published every two years in which copies may be ordered through the National Technical Information Service, Springfield, VA 22161; internet: http://www.ntis.gov/.

7. BACKGROUND.

a. Global Positioning System (GPS).

(1) System Description. The Global Positioning System is a satellite based radio navigation system, which broadcasts a signal that is used by receivers to determine precise position anywhere in the world. The receiver tracks multiple satellites and determines a pseudorange measurement that is then used to determine the user location. A minimum of four satellites are necessary to establish an accurate three-dimensional position. The Department of Defense (DOD) is responsible for operating the GPS satellite constellation and monitors the GPS satellites to ensure proper operation. Every satellite's orbital parameters (ephemeris data) are sent to each satellite for broadcast as part of the data message embedded in the GPS signal. The GPS coordinate system is the Cartesian earth-centered earth-fixed coordinates as specified in the World Geodetic System 1984 (WGS-84).

(2) System Availability and Reliability.

(i) The status of GPS satellites is broadcast as part of the data message transmitted by the GPS satellites. GPS status information is also available by means of the U.S. Coast Guard navigation information service: (703) 313-5907, Internet: http://www.navcen.uscg.mil/gpsnotices/. Additionally, satellite status is available through the Notice to Airmen (NOTAM) system.

(ii) The operational status of GNSS operations depends upon the type of equipment being used. For GPS-only equipment TSO-C129(AR), the operational status of nonprecision approach capability for flight planning purposes is provided through a prediction program that is embedded in the receiver or provided separately.

(3) Receiver Autonomous Integrity Monitoring (RAIM). When GNSS equipment is not using integrity information from WAAS or LAAS, the GPS navigation receiver using RAIM provides GPS signal integrity monitoring. RAIM is necessary since delays of up to two hours can occur before an erroneous satellite transmission can be detected and corrected by the satellite control segment. The RAIM function is also referred to as fault detection. Another capability, fault exclusion, refers to the ability of

Global Positioning System (GPS). › Equipment Classes. TSO-C129(AR) defines different classes o

the receiver to exclude a failed satellite from the position solution. Fault detection and exclusion (FDE) is provided in oceanic/remote GPS equipment (Appendix 1, paragraph 2b of this AC) and in all GPS/WAAS equipment.

(4) Selective Availability. Selective Availability (SA) is a method by which the accuracy of GPS is intentionally degraded. This feature is designed to deny hostile use of precise GPS positioning data. SA was discontinued on May 1, 2000, but many GPS receivers are designed to assume that SA is still active. New receivers may take advantage of the discontinuance of SA based on the performance values in ICAO Annex 10, and do not need to be designed to operate outside of that performance.

(5) GPS Modernization. Initiatives to modernize the Global Positioning System include two new civilian signals. One of the new signals will be centered at 1176.45 MHz, and will provide an improved service that supports safety-of-life applications, including aeronautical applications. The other new signal will be centered at 1227.60 MHz, and will be available for general use in non-safety critical applications. Depending on the rate of GPS satellite launches, initial operating capability will be available between the years 2012 and 2015.

(6) System Performance. The GPS performance specifications contained in this AC are based upon unaugmented performance achieved with the Standard Positioning Service (SPS). GPS performance for a representative single-frequency receiver, as defined in the GPS SPS Performance Standard, is summarized in the following table.

Table 1. Summary of GPS Performance Availability Unspecified Horizontal Navigation System Accuracy (95%)

33 m

Vertical Navigation System Accuracy (95%)

73 m

SIS Integrity Unspecified Service Volume Global

(7) General Operational Limitations.

(i) TSO-C129(AR) equipment: the requirements defined in TSO-C129(AR) were developed for GPS to be used in addition to other navigation equipment.

(ii) GPS Oceanic/Remote operation: the requirements specified in appendix 1 of this AC were developed for GPS to be used for limited operations (e.g. oceanic/remote operations as discussed in AC 90-94) without the need for other navigation equipment appropriate to the route to be flown.

(8) Equipment Classes. TSO-C129(AR) defines different classes of equipment to support different equipment configurations. These classes are defined in paragraph (a)(2) of TSO-C129(AR).

Satellite-Based Augmentation System (SBAS). To improve the › WAAS Performance Requirements (within Service Volume). WAAS

b. Satellite-Based Augmentation System (SBAS). To improve the accuracy, integrity and availability of GPS signals, ICAO has defined Standards and Recommended Practices (SARPs) for satellite-based augmentation systems (SBAS). The FAA developed the Wide Area Augmentation System (WAAS) to provide SBAS service throughout U.S. airspace. In addition, the FAA is working with civil aviation authorities in Europe and Japan to coordinate the development of their SBAS, (the European Geostationary Navigation Overlay System, or EGNOS, and the Japan Multifunctional Transport Satellite (MTSAT) Satellite-based Augmentation System, or MSAS).

(1) WAAS Description.

(i) The WAAS uses measurements from a wide area network of reference stations to determine satellite clock and ephemeris corrections and to model the propagation effects of the ionosphere. A monitoring system ensures that the SBAS is operating correctly and that the correction information is correct. This information is broadcast to users via a geostationary satellite, using a signal that is similar to the GPS signal. Since the SBAS satellite signal is similar to GPS, it also provides an additional pseudorange measurement to the receiver. The objectives of WAAS are:

(A) to improve the integrity of GPS through real-time monitoring;

(B) to improve the availability of GPS by providing an additional satellite signal; and

(C) to improve the accuracy of GPS by providing differential corrections.

(ii) WAAS provides a level of service that supports all phases of flight including LNAV/VNAV and LPV approaches. Both LNAV/VNAV and LPV approaches are approach procedures with vertical guidance as defined in ICAO Annex 6. These approaches provide vertical guidance, but do not meet the more stringent standards of a precision approach. In the long term, WAAS will provide Category I precision approach services in conjunction with modernized GPS. The FAA plans to decommission a significant percentage of its existing VOR and ILS infrastructure after WAAS services are available. Although requirements for surface operations are not mature, GPS/WAAS is expected to meet those requirements for a variety of surveillance and navigation applications.

(2) WAAS Availability and Reliability. The FAA will provide NOTAMs to advise pilots of the status of the WAAS. This will also include NOTAMs advising if the operational capability of GPS/WAAS equipment is degraded. WAAS monitors both GPS and WAAS satellites and provides integrity.

(3) WAAS Performance Requirements (within Service Volume). WAAS performance defined in this AC is based on a single frequency user as defined in FAA-E2892B. The performance of WAAS is summarized in the following table.

Table 2. Summary of WAAS Performance En route through Nonprecision Approach

TSO Authorization (TSOA). › Several TSO’s have been written for GNSS-related equipment a

LPV

Availability 99.999% 99.9% Horizontal Navigation System Accuracy (95%)

33 m

16 m

Vertical Navigation System Accuracy (95%)

Unspecified 20 m

SIS Integrity Probability of misleading information in an hour = 10-

7

Probability of misleading

information during an

approach = 10-7

Service volume U.S. Airspace Contiguous U.S., parts of

Alaska

(4) WAAS General Operational Limitations. The requirements were developed for GPS/WAAS to be used within the SBAS coverage without the need for other radio navigation equipment appropriate to the route to be flown. Outside of the SBAS coverage, GPS/WAAS equipment reverts to GPS-only operation.

(5) WAAS Equipment Classes. RTCA/DO-229C, section 1.4, defines the different classes of GPS/WAAS equipment to support different equipment configurations.

c. Ground-Based Augmentation System (GBAS). To improve the accuracy, integrity and availability of GPS signals, ICAO has defined Standards and Recommended Practices (SARPs) for ground-based augmentation systems (GBAS). The FAA developed the Local Area Augmentation System (LAAS) to provide GBAS service at designated airports throughout the U.S. The LAAS is intended to support a level of navigation service that requires greater performance than that provided by WAAS. LAAS is being developed to ensure interoperability. Similar to the WAAS concept that incorporates the use of communication satellites to broadcast a correction message, the LAAS will broadcast its correction message via very high frequency (VHF) radio broadcast from a ground-based transmitter. The localized coverage area will support multiple operations to an airport. The LAAS will complement WAAS at locations where WAAS is unable to meet existing navigation and landing requirements. As the LAAS is further developed, it will provide a level of service sufficient to support CAT II/III precision approach and landing operations.

8. APPROVAL PROCESS. This paragraph describes the general approval process applicable to GNSS equipment intended for IFR navigation (paragraph 9 provides guidance addressing installation of GNSS equipment for VFR use). Unique approval issues associated with GPS for Oceanic/Remote Navigation and GLONASS are defined in appendices 1 and 2, respectively.

a. TSO Authorization (TSOA).

(1) Several TSO’s have been written for GNSS-related equipment and components (reference paragraph 6a of this AC). While the TSO process operates on the basis of self-certification by the applicant, it is beneficial to involve the ACO (both

APPROVAL PROCESS. This paragraph describes the general appr › Installation of GNSS Equipment. For installation of TSO’d a

engineers and flight test pilots) in the evaluation of the equipment as early as possible for two primary reasons:

(i) Obtaining a TSOA does not ensure that the equipment will satisfy all of the applicable requirements when it is installed; and

(ii) The design of GNSS equipment has become increasingly more complex and workload intensive with no standardized interface with the pilot. The human factors evaluation of the equipment is subjective.

(2) It is recommended that the manufacturer elect to obtain an STC for their equipment concurrent with obtaining the TSOA. This has proven to be an effective means of involving the ACO and identifying issues associated with installing the article.

(3) The installation guidelines should reference standard practices used in the installation and should address the unique GNSS issues in paragraphs 11 through 20 of this AC. The installation instructions should identify each installation configuration that is supported, including the GNSS antenna(s), each autopilot make/model, other GNSS or RNAV equipment that is installed on the aircraft, and any other articles to which the equipment will interface (e.g., external switches, barometric altimeter, TAWS). In addition, the installation instructions should address the critical areas unique to each installation, such as antenna placement, unit placement (for controls/display), and electromagnetic compatibility.

(4) The operations manual must address the operation of the equipment. For installations accomplished in accordance with the installation instructions, the operations manual should also cover the operation of related components (e.g., remote source selector) for every installation configuration. If there any limitations associated with the operation of the equipment, a sample Airplane/Rotorcraft Flight Manual Supplement (A/RFMS) should also be provided (e.g., the TSO-C129(AR) limitation for other navigation equipment appropriate to the route to be flown).

b. First-Time Airworthiness Approval. Each TSO’d article should obtain a firsttime airworthiness approval through TC or STC.

(1) The initial certification of GNSS equipment involves extensive engineering and flight test evaluations as described in paragraphs 11 through 23 of this AC. Applicants are encouraged to obtain AC 21-40, an Application Guide for Obtaining a Supplemental Type Certificate.

(2) It is recommended that the ACO request a Special Certification Review (SCR) Team when evaluating GNSS stand-alone navigation equipment for the first time, typically as part of an STC. The SCR team should be coordinated through AIR-130. The team assists in applying a common standard, which will result in a more consistent evaluation.

c. Installation of GNSS Equipment. For installation of TSO’d articles after the first-time STC, the extent of FAA involvement and review for a given installation depends on the characteristics of the installation. The installer should comply with the guidelines described in paragraph 15 through 20, and should ensure continued compliance with the relevant certification regulations.

Installation of GNSS Equipment. For installation of TSO’d a › For these installations, any A/RFM(S) associated with the or

(1) Evaluation of installation. The installation should be evaluated to classify the installation and determine the type of approval vehicle. The following guidelines are provided:

(i) Major change to type design: Per 14 CFR Part 21.93, the applicant should determine if the installation has an appreciable effect on the structural strength or operational characteristics affecting the airworthiness of the product. An example is installation in multiple-pilot aircraft where another, dissimilar area navigation system is also installed (see paragraph 18f), which should be thoroughly evaluated under the TC/STC process unless intermixing of the same GNSS equipment was part of the initial design approval or specifically addressed under an approved model list (e.g., the Brand-A, model X instructions may adequately address intermixing with Brand-A model Y equipment).

(ii) Major alteration: Per 14 CFR Part 43 Appendix A, installation of GNSS equipment may be a major alteration requiring FAA-approved data pertinent to that installation. For example, installation of the GNSS antenna may impact structural strength, and the GNSS equipment may be connected to other equipment that has not been previously determined to be compatible or for which the installation instructions are not adequate to ensure compatibility under all conditions. If the installation is determined to be a major alteration, the applicant can obtain an STC or a field approval using FAA Form 337 (Major Repair and Alteration).

(iii) Minor alteration: Under the original AC 20-138, installation of GPS equipment required the use of approved data (under an STC or major alteration) because GPS was a new and unique technology. However, since GPS technology is now common and considerable experience has been obtained in the installation of GPS, approved data for every installation is no longer appropriate. Instead, installations that do not qualify as major alterations above should be accomplished as minor alterations. These installations should be based on acceptable data including the following:

(A) Data previously approved as applicable to the aircraft (e.g., STC, Approved Model List).

(B) Data previously approved as applicable to a different make/model aircraft (e.g., an initial STC obtained by the equipment manufacturer), provided the installation is installed in accordance with the manufacturer’s instructions, any equipment interfaces are adequately addressed in the installation instructions for the GNSS equipment and the equipment with which it is interfacing, and the equipment is installed in accordance with the guidelines in this AC. For example, installation of GNSS navigation equipment that only interfaces with an antenna, power, ground, an external HSI/CDI with a single source selector switch, and a left/right (deviation-based) autopilot would typically be considered a minor alteration.

(2) For these installations, any A/RFM(S) associated with the original approved data should be used as the basis for an A/RFM(S) for this installation. Limitations imposed on the GNSS equipment during the initial approval should be imposed for follow-on equipment approval unless an FAA re-evaluation of the relevant issues determines that they do not apply. An A/RFM(S) is not necessary if it was not part of the original installation, if the operating manual addresses the use of the equipment and

GNSS EQUIPMENT LIMITED TO VFR USE. GNSS equipment may be in

associated installed components (e.g., remote source selection), and there are no unique limitations associated with the particular installation.

(3) The installation performance tests (paragraphs 22 and 23) must be successfully completed. The installation performance tests are usually conducted in two parts, the ground checks and the flight checks. The aircraft can be approved for return to service following the required ground checks, however the GNSS equipment cannot be used for flight under Instrument Flight Rules (IFR) until the flight checks have been accomplished and would have to be placarded as such.

(4) Upgrading previously-approved installations.

(i) WAAS Upgrade. GPS TSO-C129(AR) equipment may be upgraded to TSO-C145a or TSO-C146a compliance. Manufacturers who provide an upgrade path are encouraged to use an approved model list to streamline the approval of subsequent installations. The guidance in paragraph 8c(1) also applies to the upgrade of previously installed equipment.

(ii) Additional GNSS equipment. Some applicants are expected to retain existing TSO-C129(AR) equipment and add TSO-C146a equipment. Compatibility between the equipment should be established in accordance with paragraph 18f. The original TSO-C129(AR) installation should not be re-evaluated, except for modifications made as part of the TSO-C146a installation. The re-evaluation should be to the affected functions or performance. For example, if the equipment shares a GNSS antenna there will be additional signal loss for the original equipment and compliance to the original TSO-C129(AR) installation instructions should be verified.

(iii) Re-use of GNSS antenna. WAAS or LAAS equipment may be added to an aircraft (as an addition or as modification to existing GPS equipment) with a previously installed GNSS antenna. This may be accomplished by including the antenna under the WAAS or LAAS TSO authorization, by establishing compatibility under the WAAS or LAAS TSO authorization, or demonstrating compatibility at time of installation (see paragraph 17a). If a WAAS or LAAS TSOA holder demonstrates compatibility with a previously-approved antenna (approved under TSO-C129(AR)), the installation instructions should state the part number of the compatible antenna. Note that compatibility to support LPV or GLS operations cannot be addressed without new design data on the antenna (see paragraph 11e).

(iv) Marking. When equipment is upgraded to a new TSO (e.g., from TSO-C129(AR) to TSO-C146a), the marking must be modified to reflect the new configuration and approval. This marking change can be accomplished by a certificated person in accordance with the TSO authorization holder’s instructions (e.g., service letters or service bulletins). A certificated person in this context is defined as one who is authorized under 14 CFR section 43.3, Persons authorized to perform maintenance, preventative maintenance, rebuilding, and alterations.

9. GNSS EQUIPMENT LIMITED TO VFR USE. GNSS equipment may be installed on a no-hazard basis as a supplement to VFR navigation. Such installations need only to verify that the GNSS installation does not introduce a hazard to the aircraft (e.g., properly secured for crashworthiness, not combustible, etc). GNSS installations limited to VFR USE ONLY should be evaluated under the criteria described in paragraph

TSO-C145a and TSO-C146a Deviations. › Under TSO-C129(AR), many deviations have been granted to man

8c(1) to classify the type of aircraft/appliance modification. The only exception is that, for installations where the GNSS equipment does not interface with other equipment (except a dedicated remote indicator if applicable), the installation can be accomplished without any reference to previously approved data (i.e., the equipment does not need a TSO or prior STC). Installation guidelines for such an installation are provided in appendix 5 of this AC. Loss of or misleading VFR navigation information is considered a minor failure condition; therefore, Software Development Assurance Level D is acceptable. A readable placard stating "GPS limited to VFR use only" must be installed in clear view of the pilot, unless the equipment automatically displays this message on start-up and pilot action is required to clear the message. An A/RFM(S) is not required since the placard or display contains the equipment limitation.

10. TSO AUTHORIZATIONS. This paragraph provides guidance on granting TSO Authorizations for GNSS-related equipment. Only issues that are unique to GNSS equipment are discussed.

a. Applicability of TSO-C129(AR).

(1) TSO-C129(AR) define an acceptable standard for GPS equipment intended to be used as a supplement to other navigation systems.

(2) There is no plan to cancel TSO-C129a, and manufacturers may continue to obtain new TSO authorizations under TSO-C129a. In addition, there is no plan to withdraw TSO-C129(AR) authorizations, so manufacturers of TSO-C129(AR) equipment can continue to manufacture that equipment, and the equipment is still eligible for installation in accordance with the guidance in this AC.

b. Multiple TSO Authorizations. Multiple TSO authorizations may be granted for equipment that accomplishes multiple functions. However, the number of TSO markings on GNSS equipment should be minimized to avoid confusion during installation and approval. The following combinations of TSO authorizations should not be granted, as the TSOs either contradict each other or are superfluous to a TSO with broader scope:

(1) TSO-C129(AR) must not be combined with TSO-C145a or TSO-C146a;

(2) TSO-C145a must not be combined with TSO-C146a Class 1, 2 or 3 equipment. The combination of TSO-C145a with TSO-C146a Class 4 equipment is permitted; and

(3) TSO-C146a must not be combined with TSO-C115(AR).

(4) Any class of TSO-C129(AR) may be combined with TSO-C161, and should be marked accordingly.

c. TSO-C145a and TSO-C146a Deviations.

(1) Under TSO-C129(AR), many deviations have been granted to manufacturers due to the relative immaturity of the TSO, which significantly modified the industry standard (RTCA/DO-208). Applicants for TSO-C145a and TSO-C146a should not expect the same latitude when requesting deviations. These TSOs are based on the industry standard (RTCA/DO-229C) which has been internationally harmonized and received a good deal of scrutiny since it was first published in January 1996.

Technical Data. Paragraph 9c of Order 8150.1A, Technical St › The ACO should review the installation manual. The manufact

(2) When requesting a deviation to these TSOs, the applicant must substantiate how their implementation is equivalent. A primary objective of RTCA/DO-229C is to standardize the interface and provide compatibility across equipment from different manufacturers. Therefore, the statement of equivalency for deviations to the pilot interface requirements must also include how the implementation is operationally compatible with other GPS/WAAS equipment.

(3) Deviations that are granted to these TSOs will be made available and will be incorporated into the next revision of the TSO to ensure that all manufacturers have the same opportunity to deviate.

d. Technical Data. Paragraph 9c of Order 8150.1A, Technical Standard Order Procedures states that the ACO may elect to do a cursory review of the TSO submittal package. Due to the complexity of GNSS equipment, the ACO should:

(1) Evaluate manufacturer supplied bench test data on the equipment and verify that the tests comply with the relevant procedures and requirements (TSO-C129, and sections 2.4 and 2.5 of RTCA/DO-229C and RTCA/DO-253A as applicable) and that the equipment has passed applicable tests.

(2) Verify compliance with the appropriate environmental qualification standards and tests in RTCA/DO-160(AR).

(3) Verify compliance to the design assurance levels consistent with the failure condition hazard classification. If the criteria in AC 23-1309-1C for different Classes of Part 23 aircraft is applied, the installation instructions must include a summary of the approval and a limitation. For example, TSO-C146a Class 3 equipment (GPS/WAAS precision approach stand-alone equipment) with software developed to RTCA/DO-178B Level C would state the following:

“This equipment complies with paragraph 3a of TSO-C146a for Class I, II, and III aircraft as defined in AC 23-1309-1C. This equipment is not eligible for installation in Part 25 or Part 23 Class IV aircraft unless the precision approach mode is disabled through the following equipment configuration setting: ….”

(4) Verify compliance with the appropriate software qualification standards and tests in RTCA/DO-178B.

(5) Verify the approval of a data process capable of updating the navigation database for GNSS stand-alone navigation equipment (TSO-C129(AR) Class A, TSO-C146a). RTCA/DO-200A defines an acceptable means of ensuring that the aeronautical data process does not corrupt data, from the publication of data by a State to its application in the equipment. The data quality requirements must be defined, including any limitations or incompatibilities between the navigation function and the database (e.g., incompatible ARINC 424 leg types, leg length limitations).

(6) The ACO should review the installation manual. The manufacturer should include all known installation limitations, and special attention should be given to reviewing those limitations in light of the variety of different installation configurations that are supported.

(7) For TSO-C146a, the pilot’s guide should be reviewed by an FAA flight test pilot familiar with the equipment to ensure it is complete, concise, and easy to understand.

Antennas authorized under TSO-C129(AR). A number of antenna › Antennas authorized independently from a GPS receiver. TSO-

(8) For TSO-C146a, the quick reference guide should be reviewed by an FAA flight test pilot familiar with the equipment. Recommended format and content for this guide can be found in appendix 3 of this AC.

(9) For TSO-C146a, the training program should be reviewed by an FAA flight test pilot familiar with the equipment. This training program may be a series of manuals, a videotape, interactive CD-ROM, etc. Due to the inherent complexity in area navigation operations, it is important that these training materials are useful and help pilots learn to operate the equipment.

e. Major/Minor Design Changes. The following changes are among those generally considered by the FAA to be major changes (per 14 CFR Part 21.611). After consultation with the ACO on a specific change, the ACO and manufacturer may determine that particular change is a minor design change.

(1) Changes to the navigation or integrity algorithms; and

(2) Changes to navigational display formats and navigation/function operating procedures.

11. EQUIPMENT PERFORMANCE – GPS ANTENNA. This paragraph provides guidance related to the basic functions and performance of the GNSS antenna. The antenna does not have to be installed in an aircraft to comply with the means defined in this paragraph. Typically, this guidance will be applicable to the manufacturer who is seeking a TSO Authorization (TSOA). If the manufacturer does not obtain a TSOA, this paragraph would apply as part of the initial airworthiness approval. These issues do not need to be revisited for antennas that hold a previously granted TSO authorization under TSO-C129(AR) or TSO-C144, or minor modifications to such equipment. However, the applicant may elect to address these issues to demonstrate that the antenna is compatible with a WAAS or LAAS installation.

a. TSO-C144, Airborne Global Positioning System Antenna, defines an acceptable means of compliance for a GNSS antenna. Applicants should comply with RTCA/DO-228, Change 1.

b. Antennas authorized under TSO-C129(AR). A number of antennas were authorized under TSO-C129(AR), before TSO-C144 became available. This paragraph addresses the performance of these antennas.

(1) Antennas authorized as part of GPS receiver TSOA. Antennas authorized in conjunction with a GPS receiver under TSO-C129(AR) may continue to be installed along with the associated receiver. These antennas must not be installed with a different receiver unless the antenna part number is listed in the receiver installation instructions as being compatible.

(2) Antennas authorized independently from a GPS receiver. TSO-C129(AR) does not provide an adequate standard to ensure interoperability between GPS antennas,

EQUIPMENT PERFORMANCE – GPS ANTENNA. This paragraph provide › Differential Group Delay. The differential group delay is d

and must not be applied to antennas without reference to a specific GPS receiver. However, some antennas have been approved under an authorization to TSO-C129(AR) without reference to a specific GPS receiver. These antennas should not be installed with any new receivers (i.e., one for which a previous TC/STC does not exist) unless the antenna part number is listed in the receiver installation instructions as being compatible. Antenna manufacturers should obtain TSO-C144 for their antennas as quickly as practical to ensure compatibility with receiver equipment and to facilitate installation.

c. Lightning Qualification. The RTCA/DO-160D category for lightning induced transient susceptibility that best represents the transient induced in the antenna cable during the Direct Effects of Lightning test (Section 23 of RTCA/DO-160D) should be identified for comparison to the receiver susceptibility at time of installation.

d. Signal Power/Loss. The following issues should be addressed in the installation instructions.

(1) Passive antennas authorized under TSO-C144. Passive antennas are those without a preamplifier (reference RTCA/DO-228, section 2.2.1). The maximum (and minimum, if applicable) signal loss between the antenna output port and receiver input port must be defined, to yield the maximum and minimum receiver sensitivities defined in section 2.1.1.10 of RTCA/DO-229C. This information should be described as a function of the type and lengths of interconnecting cable and type and number of connectors or specified as the limit of cable loss in dB.

(2) Active antennas authorized under TSO-C144. An active antenna is defined as one that includes a low noise power amplifier as part of the antenna assembly (reference RTCA/DO-228, section 2.2.2). The installation instructions must identify the maximum and minimum output power (may be specified as pre-amplifier gain) and amplifier noise figure. These guidelines can be compared to the minimum and maximum power inputs defined in the GNSS receiver installation instructions. Guidelines on the loss associated with recommended cables and connectors should be provided so that the installer can determine the maximum and minimum signal power at the receiver port. This range will be compared to the range specified by the GNSS receiver manufacturer at time of installation. In addition, the installation instructions should identify any conditions under which out-of-band emissions (e.g., SATCOM) can create in-band intermodulation products that may interfere with receiver operation.

(3) Antennas authorized with a specific receiver (TSO-C145a, TSO-C146a, TSO-C161). The installation instructions must identify the maximum (and minimum, if applicable) signal loss between the antenna output port and receiver input port to yield the maximum and minimum receiver sensitivities defined for the receiver. This information should be described as a function of the type and lengths of interconnecting cable and type and number of connectors or specified as the limit of cable loss in dB.

e. Differential Group Delay. The differential group delay is defined within section 2.1.4.5 of RTCA/DO-229C and section 2.3.6.4.1of RTCA/DO-253A. The differential group delay of the antenna must be documented in the installation instructions for those antennas intended to support LPV and GLS approach operations. Antennas have filters that could affect the delay. The differential group delay of the antenna is defined in section 2.2.3 of RTCA/DO-228.

Acceptable Means. › GPS/LAAS. TSO-C129(AR) and TSO-C145a define two acceptable m

12. EQUIPMENT PERFORMANCE – GNSS SENSOR. This paragraph provides guidance related to the basic functions and performance of the GPS sensor, including those sensors that integrate WAAS or LAAS. This paragraph also applies to sensors embedded within stand-alone navigation equipment. Appendix 2 provides unique guidance material for GPS sensors that integrate GLONASS. The sensor does not have to be installed in an aircraft to comply with the means defined in this paragraph. Typically, this guidance will be applicable to the manufacturer who is seeking a TSO Authorization (TSOA) for TSO-C129a, TSO-C145a, TSO-C146a, TSO-C161, or TSO-C162. If the manufacturer does not obtain a TSOA, this paragraph would apply as part of the initial airworthiness approval. These issues do not need to be revisited for equipment that holds a previously granted TSO authorization under TSO-C129(AR), or minor modifications to such equipment.

a. Acceptable Means.

(1) GPS. TSO-C129(AR) defines an acceptable means of compliance for GPS equipment that is intended to supplement other navigation equipment on the aircraft. With one exception, GPS equipment that complies with this standard has a limitation that the aircraft must be equipped with other means of navigation appropriate to the route to be flown. The exception is the use of this equipment for oceanic and remote operation, if several additional features are provided as described in appendix 1 of this AC.

(2) GPS/WAAS. TSO-C145a and TSO-C146a, which reference RTCA/DO-229C, define an acceptable means of compliance for this equipment when operating in GPS or GPS/WAAS modes. RTCA/DO-229C is a complete set of standards for GPS and GPS/WAAS. While applicants may elect to use portions of RTCA/DO-229C to supplement the earlier standards for TSO-C129(AR) equipment, it is not appropriate to obtain TSO-C129(AR) authorization in conjunction with TSO-C145a or TSO-C146a equipment. GPS/WAAS equipment that complies with the standards in DO-229C does not have a limitation that the aircraft must be equipped with other means appropriate to the route to be flown.

(3) GPS/WAAS/LAAS sensor. TSO-C145a and TSO-C146a define an acceptable means of compliance for this equipment when operating in the GPS or GPS/WAAS modes. When operating in the GPS/LAAS mode, the equipment should comply with the requirements of TSO-C161 and Section 2 of RTCA/DO-253A.

(4) GPS/LAAS. TSO-C129(AR) and TSO-C145a define two acceptable means of compliance for this equipment when operating in GPS mode (i.e., outside the coverage of a selected LAAS ground facility). When operating in the GPS/LAAS mode and conducting a GLS approach, the equipment must comply with the requirements of Section 2 of RTCA/DO-253A. When operating in GPS/LAAS mode and not conducting a GLS approach, the equipment must comply with the sensor requirements of RTCA/DO-253A (for position, velocity and time) and the navigation requirements of TSO-C129(AR). For Class B1 and B2 equipment, the requirements in TSO-C129(AR) paragraph (a)(4)(vii) do not apply when a LAAS-correction position is being used. For Class C1 and C2 equipment, the requirements in TSO-C129(AR) paragraph (a)(5)(vii) do not apply when a LAAS-corrected position is being used. GPS/LAAS equipment carries

Non-Standard Mask Angle. All equipment has a mask angle, th › Prediction programs and availability assessments intended to

the basic GPS limitation that the aircraft must be equipped with other means of navigation appropriate to the route to be flown.

b. Compatible GNSS Antennas. Compatible antennas should be identified. This may include a generic reference to TSO-C144-compliant antennas, refer to a specific GNSS antenna (part number) that is included as part of the receiver design approval (e.g., part of receiver TSOA), or a part of another receiver design approval (also by part number). When using an antenna that is part of a separate design approval, the receiver manufacturer should use the antenna specification provided by the antenna manufacturer and should coordinate the compatibility finding with the antenna manufacturer. Otherwise, minor design changes to the antenna could be made by the antenna manufacturer that would adversely impact the operation of the GNSS equipment.

c. Non-Standard Mask Angle. All equipment has a mask angle, the elevation angle above the horizon at which the GNSS receiver considers satellites for use in the solution. The accuracy and reliability of GPS signals is affected by a number of factors, including shadowing of the signal (by a portion of the aircraft or local terrain), the GPS antenna gain and atmospheric effects (ionosphere and troposphere).

(1) A 5 degree mask angle is standard (7.5 degree mask angle for TSO-C129(AR)). Sensors may track a satellite below 5 degrees, but must not incorporate it in the navigation position solution unless the accuracy is demonstrated for satellites at the design mask angle. The sensor may use a weighted position solution, which deweights satellites at low elevation angles based on the accuracy demonstrated for those elevation angles.

(i) For equipment that assumes that GPS selective availability is active (assumed pseudorange accuracy of ≥33m rms), the ionospheric, tropospheric, and airframe multipath errors can be considered negligible down to 2 degrees. The use of a mask angle below 2 degrees requires validation of the error models for these effects.

(ii) For GPS equipment that takes advantage of the discontinuance of selective availability (assumed pseudorange accuracy of <33m rms), the aviation community has validated error models down to a 5 degree mask angle (see RTCA/DO-229C, Appendices A and J). The use of a mask angle below 5 degrees requires validation of the error models for these effects.

(iii) The accuracy must account for the errors caused by receiver noise and interference. This may be accomplished by calibrating the pseudorange accuracy with a measured signal-to-noise ratio, or by using a demonstrated tracking accuracy at low elevation angles. To demonstrate tracking accuracy, the actual antenna characteristics below 5 degrees must be used when demonstrating compliance to the performance characteristics defined in TSO-C129(AR), RTCA/DO-229C or RTCA/DO-253A. This means that the received GPS signal power must be adjusted down to reflect the minimum antenna gain relative to -4.5dBic for a standard antenna, while the interference power cannot be adjusted down as the location of the interference emitter is unknown. Any associated limitations on the installation (e.g., standard ground plane) should be identified in the installation instructions.

(2) Prediction programs and availability assessments intended to support flight planning functions must use the equipment mask angle except as follows:

Prediction Programs. Unlike conventional ground-based navig › Prediction Program Requirements. The following guidelines a

(i) In order for the prediction program to take advantage of the discontinuance of selective availability for satellites below 5 degrees, the prediction program must use the demonstrated tracking accuracy as described in paragraph 12c(1)(iii) (including accounting for the specific antenna characteristics and effects of interference). TSO-C144 gain characteristics may be used if the antenna is TSO-C144 compliant. Alternately, antenna characteristics below 5 degrees may be identified, a specification for low-elevation angle performance defined, and the antenna must obtain a design and production approval according to that specification. This may be accomplished by including the antenna as part of the GNSS manufacturer’s TSOA.

(ii) For en route, terminal and nonprecision approach operations, the predicted mask angle cannot be below 2 degrees.

(iii) For precision approach and LPV, the predicted mask angle cannot be below 5 degrees.

d. Interference Testing. The GPS and WAAS signal acquisition and track performance, WAAS message loss rate, integrity and accuracy requirements will be verified during minimum signal conditions and defined interference conditions. These tests must be conducted in accordance with the test conditions and procedures specified in TSO-C129(AR) or RTCA/DO-229C, as appropriate.

e. Prediction Programs. Unlike conventional ground-based navigation aids which have a direct correlation between a facility outage (VOR fails) and the loss of an operational capability (VOR approach is unavailable), GPS satellite failures have a nonintuitive impact on operational capability. The operator is responsible for considering the effects of satellite outages during flight planning. Prediction programs and availability assessments are essential to enabling the operator to fulfill this responsibility.

(1) The FAA plans to provide NOTAM service for all approach operations using TSO-C145a or TSO-C146a equipment, and for GLS operations using LAAS equipment.

(2) For oceanic/remote operation based on GPS, a prediction program must be provided to determine if GPS satellite outages have an operational impact on oceanic/remote operations.

(3) For basic RNAV operations in Europe, a prediction program should be provided (see AC 90-96 for additional information). Alternatively, basic RNAV operations can be supported by the generic Eurocontrol prediction tool (http://augur.ecacnav.com/).

(4) For non-precision approach operations using TSO-C129(AR) equipment, manufacturers must provide a prediction availability based upon RAIM. For nonprecision approach operations using GPS/WAAS equipment, this capability should be provided to support GPS operations outside of the WAAS coverage area.

(5) Prediction Program Requirements. The following guidelines apply to any prediction program that is intended to assess the operational impact of satellite outages for flight planning purposes (it does not apply to the prediction described in paragraph (a)(3)(xv)4a of TSO-C129(AR)).

EQUIPMENT PERFORMANCE – STAND-ALONE NAVIGATION EQUIPMENT. I

(i) This prediction program can be provided on any processing platform (in the GPS equipment or not).

(ii) The prediction program software should be developed in accordance with at least RTCA/DO-178B/EUROCAE 12B, level D guidelines.

(iii) The program should use either a RAIM algorithm identical to that used in the airborne equipment, or an algorithm based on assumptions for RAIM prediction that give a more conservative result.

(iv) The program should calculate RAIM availability based on the same satellite mask angle used in the equipment, but not less than 2 degrees for en route and terminal operations or 5 degrees for precision approach or LPV operations.

(v) The program should have the capability to manually designate GPS satellites which are expected to be out-of-service for the intended flight.

(vi) For en route predictions, the program should allow the user to select the intended route (including declared alternates) and the time and duration of the flight. The maximum outage of RAIM (and FDE, if applicable) should be provided, and any predicted outages of navigation capability must be identified. Note that for oceanic/remote operations, the maximum duration of an FDE outage cannot exceed 34 minutes for RNP-10 operation (see Order 8400.12a) and 51 minutes for MNPS operation (see AC 90-94). For B-RNAV operations, the maximum acceptable duration of a RAIM outage is 5 minutes (see AC 90-96).

(vii) For approach predictions, the program should allow the user to select the destination and expected time of arrival, and provide a RAIM availability prediction over an interval of at least +15 minutes computed in intervals of 5 minutes or less about the ETA.

f. Interface Requirements

(1) Interface to multi-sensor navigation systems. Equipment requirements applicable to the integration of a GNSS sensor with a multi-sensor navigation system are in TSO-C129(AR) (Class B and C equipment) and TSO-C115b.

(2) Interface to non-navigation systems. GNSS sensors may provide output to a variety of applications, including terrain awareness and warning systems (TAWS), automatic dependent surveillance (ADS), and moving map displays for situational awareness. The interface should be specified, and compatible equipment identified to streamline installation approvals.

13. EQUIPMENT PERFORMANCE – STAND-ALONE NAVIGATION EQUIPMENT. In addition to the guidance in this paragraph, stand-alone navigation equipment incorporates an antenna and a sensor and should comply with the guidance in paragraphs 11 and 12 of this AC. These issues do not need to be revisited for equipment that holds a previously granted TSO authorization under TSO-C129(AR), or minor modifications to such equipment.

Controls. › Particular attention should be placed on the controls requir

a. Acceptable Means.

(1) GPS. TSO-C129(AR) defines an acceptable means of compliance for GPS equipment.

(2) GPS/WAAS. TSO-C146a defines an acceptable means of compliance for GPS/WAAS equipment. RTCA/DO-229C is a complete set of standards for GPS and GPS/WAAS and should not be used in conjunction with TSO-C129(AR).

Note: In addition to the sensor improvements, there are a number of differences between TSO-C129(AR) and TSO-C146a, most notably the compatibility of TSO-C146a equipment with RNP RNAV operations, more explicit pilot interface requirements (see RTCA/DO-229C, section 2.2.1.1), and a Vector-to-Final capability (see RTCA/DO-229C, section 1.8.2.4).

(3) GPS/WAAS/LAAS. TSO-C146a defines an acceptable means of compliance for this equipment when operating in the GPS/WAAS mode. When operating in the GPS/LAAS mode and conducting a GLS approach, the equipment must comply with the requirements of section 2 of RTCA/DO-253A. When operating in the GPS/LAAS mode and not conducting a GLS approach, the equipment must comply with the sensor requirements of section 2 of RTCA/DO-253A (for PVT) and the navigation requirements of RTCA/DO-229C (section 2.2).

(4) GPS/LAAS. TSO-C129(AR) defines an acceptable means of compliance for this equipment when operating in GPS mode (i.e., outside the coverage of a selected LAAS ground facility). When operating in the GPS/LAAS mode and conducting a GLS approach, the equipment must comply with the requirements of section 2 of RTCA/DO-253A. When operating in GPS/LAAS mode and not conducting a GLS approach, the equipment must comply with the sensor requirements of section 2 of RTCA/DO-253A and the navigation requirements of TSO-C129a, Class A1 or A2 (except the RAIM requirements of paragraph (a)(3)(xv)).

b. Evaluation of Human Factors.a

(1) The applicant is encouraged to involve the ACO as early as possible in the evaluation of the pilot interface.

(2) Controls.

(i) Appropriate feedback must be supplied during data entry, with confirmation of input action prior to activation based upon that input. Any equipment prompts must be easily understood. A suitable interface should be provided to allow data input, data output, and control of equipment operation.

(ii) Particular attention should be placed on the controls required to perform operations that occur with a high frequency or that must be conducted under potentially stressful or busy conditions such as terminal area operations and missed approaches. The workload associated with accessing the Direct-To function, entering a Hold mode, executing a missed approach, and initiating an approach to a different runway at the same airport (or to the alternate airport) following a missed approach should be minimized.

Evaluation of Human Factors.a › Prompts. Where possible, prompts should specifically indica

(iii) Controls intended for use in flight should be designed to minimize errors and, when operated in all possible combinations and sequences, should result in a condition whose presence or continuation would not be detrimental to the continued performance of the equipment. Controls should be designed to maximize operational suitability and minimize pilot workload. The amount of force required to activate knobs/buttons should be acceptable, feedback to the pilot should be adequate, and risk of inadvertent activation or deactivation should be minimized. Knob shape and size should not interfere with equipment use and should help distinguish controls. Reliance on pilot memory for operational procedures should be minimized. For those procedures that require pilot memory items, the memory item steps should be minimal and as intuitive as possible. The control/display should be operable with the use of only one hand.

(iv) Controls that are normally adjusted in flight should be readily accessible and properly labeled as to their function. Controls that are not normally adjusted in flight should not be readily accessible to the flight crew. Labels should be horizontally oriented, unobstructed by use of controls, descriptive of control function, and consistent across the equipment. The use of abbreviations should be minimized. When abbreviations are used, they should conform to section 2.2.1.1.5 of RTCA/DO-229C.

(v) Controls should be arranged logically according to functional groups, sequence of use, and frequency of use. All displays and controls must be arranged to facilitate equipment usage.

(3) Messages.

(i) Standard pilot terminology should be used and their meaning should be readily understood.

(ii) Messages should indicate what action should be considered or taken and should employ the minimum number of words required to convey its meaning. Messages or annunciation of messages not relevant to the execution of an approach, landing, rollout, or missed approach should be suppressed during the approach. Messages not requiring pilot action during flight should not be shown during flight. Messages should be operationally relevant to current or upcoming phases of flight. Pilot recall of messages from the message storage queue should bring up the most important messages first. The hierarchy of messages should be determined by the impact of the message on the safety of the flight for the current and upcoming phases of flight. Presentation of messages should not obscure safety-critical portions of guidance displays. Messages requiring prompt pilot action should stay up until action is taken or the pilot cancels the message. Safety-critical messages should be accompanied by an aural alert if that alert is not already provided by another aircraft system. Messages of operational significance to the flight should not time out.

(4) Prompts. Where possible, prompts should specifically indicate what programming action should be done next (e.g., “enter next waypoint”). Where possible, prompts should indicate the specific control that should be used next, rather than relying on pilot memory. Multiple prompts requiring different actions should be presented sequentially rather than concurrently.

Navigation Database. For area navigation equipment, the nav › Government-Provided Electronic Database. Electronic databas

(5) Cross-Track Deviation Display. Minimum discernible movement, accuracy of the centered display, resolution of the electrical output, linearity of the display and/or electrical output, and display latency should be as specified in section 2 of RTCA/DO-229C for applicable navigation modes. Deviation display designs with display ranges and resolutions outside the bounds of the required values should be substantiated by demonstration, by reference to appropriate empirical data, or by similarity to previous certified range/resolution displays.

(6) For TSO-C146a equipment, the flight crew workload requirements in section 2.2.1.1.3 of RTCA/DO-229C are particularly important and compliance to the requirements should be verified. The manufacturer must also have specific and detailed rationale for deviating from any of the recommendations defined in Table 2-4 of RTCA/DO-229C.

(7) For TSO-C146a equipment, the manufacturer must identify any acronyms that do not comply with the recommendation in RTCA/DO-229C, section 2.2.1.1.7 for the terms listed. A specific and detailed rationale for deviating must be documented.

(8) For TSO-C146a equipment, compliance to the requirements should be demonstrated by the manufacturer under the test procedures specified in section 2.5.11.3 of RTCA/DO-229C. Someone not familiar with the development of the equipment should conduct these tests to properly evaluate the pilot interface, documentation, and training information. This person should have minimal experience with the equipment, other than the opportunity to review the documentation and training materials to be supplied with the equipment.

c. Navigation Database. For area navigation equipment, the navigation database is an essential component of the ability of the equipment to perform its intended function. Guidelines pertaining to the navigation database can be found in RTCA/DO-200A. The manufacturer should pay particular attention to the specification of the format of data loaded into the navigation database, as described in RTCA/DO-200A, Appendix C.

(1) Database Process. The equipment manufacturer is usually the last link in the aeronautical data processing chain, as the format for the data loaded in the final database is typically proprietary. The applicant for a TSOA must define the data quality requirements for the database, and there must be an aeronautical data process which will be accessible to the equipment users. RTCA/DO-200A provides an acceptable means of compliance for defining the data quality requirements, and for the aeronautical data process.

(2) Reference System. The operations manual or A/RFM(S) should explain that GNSS navigation is referenced to the WGS-84 coordinate system. The following text is recommended: “Navigation information is referenced to WGS-84 reference system, and should only be used where the Aeronautical Information Publication (including electronic data and aeronautical charts) conform to WGS-84 or equivalent.”

(3) Government-Provided Electronic Database. Electronic databases sponsored by a government organization should follow the same database assurance processes as described above and in RTCA/DO-200A. GNSS equipment compatibility with government-provided electronic databases must be verified.

Failure Classification. › From en route and terminal operations, the loss of navigatio

d. Conversion of data for WAAS LNAV/VNAV approaches. As described in section 2.2.4.3.1 of RTCA/DO-229C, a final approach segment (FAS) datablock is not provided for standalone LNAV/VNAV approaches. The vertical path for such approaches is defined by the threshold location, threshold crossing height, and glidepath angle. However, the altitude of the threshold is published as the height above mean sea level (MSL), rather than as the height above the WGS-84 ellipsoid. Therefore, the published MSL height (interpreted as a height above the WGS-84 geoid) must be converted to height above the WGS-84 ellipsoid prior to being used. This conversion is not considered alteration of data per RTCA/DO-200A section 2.4.2, since it changes the reference system but not the actual vertical location. It is recommended that this conversion be accomplished within the GNSS equipment itself so that there are consistent navigation database requirements for GNSS LNAV/VNAV equipment and barometric VNAV equipment.

14. EQUIPMENT PERFORMANCE – LAAS VDB RECEIVER.

a. Section 2 of RTCA/DO-253A defines an acceptable means of compliance for LAAS VHF data broadcast receivers.

b. The receiver should be tested using the test procedures specified in section 2.5.2 of RTCA/DO-253A.

15. INSTALLATION ISSUES – GENERAL. The following issues apply to the installation of all GNSS equipment intended for IFR use.

a. Failure Classification.

(1) From en route and terminal operations, the loss of navigation function is typically considered to be a major failure condition for the aircraft (see AC 25.1309-1; AC 23.1309-1; AC 27-1; or AC 29-2 as applicable to the aircraft). Other aircraft navigation systems should be considered when determining the loss of the GNSS navigation function, which could be major (no other navigation systems) or minor (other applicable navigation systems). GNSS navigation data is considered to be misleading when unannunciated position errors exist. For en route, terminal, and non-precision approach (NPA) and LNAV/VNAV approaches, presenting misleading information to the flight crew is also considered to be a major failure condition for the aircraft. For LPV and GLS approaches, presenting misleading information to the flight crew is considered to be a hazardous failure condition. These failure classifications are summarized in Table 3.

Table 3. Typical Hazard Classifications

En route/ Terminal

Area/

NPA (LNAV)

NPA with Vertical

Guidance (LNAV/VNAV)

LPV Approach

GLS Precision Approach

(Cat. I)

Loss of Navigation Major Major Major Major Misleading Information

Major Major Hazardous Hazardous

(2) The applicant must conduct a safety assessment of the GNSS equipment installation to verify that design errors and failure modes meet the probability requirements for that failure class. AC 25.1309-1, AC 23.1309-1, AC 27-1, or AC 29-2, per the latest revision levels as applicable, provide an acceptable means for showing that the hardware complies with pertinent airworthiness requirements.

Antenna Placement. › The installer must ensure that a 5 degree mask angle (or low

b. Software Considerations. AC 20-115, current edition, defines an acceptable means of qualifying software. The applicant is encouraged to submit the Plan for Software Aspects of Certification (PSAC) early in the software development process. Early submittal will allow timely resolution of issues such as partitioning and determination of software levels.

c. Installation Instructions.

(1) The equipment must be installed in accordance with the instructions and limitations provided by the manufacturer of the equipment.

(2) Equipment should be installed with separation between wires of redundant equipment (see AC 43.13-1B).

d. Environmental Considerations.

(1) Most equipment will have been tested by the manufacturer to the environmental categories described in RTCA/DO-160(AR), with results described in an environmental qualification form. For this equipment, the environmental categories (or criteria) to which the equipment has been tested must be compatible with the aircraft environment in which the GNSS equipment is installed.

(2) For equipment which has not been tested to the environmental categories described in RTCA/DO-160(AR), comparable testing must be conducted and a thorough definition of the aircraft environment must be developed through testing of the normal and abnormal environments. At a minimum, the environmental performance requirements identified in section 2.4 of RTCA/DO-229C must be met for all components in the airborne GNSS equipment.

16. INSTALLATION ISSUES – GPS ANTENNA. This paragraph provides guidance related to the installation of a GPS antenna.

a. Antenna Placement.

(1) The antenna installation should minimize the potential for signal blockage by any portion of the aircraft during aircraft maneuvering. Shadowing by aircraft structure can adversely affect the operation of the GNSS equipment. Typically, a GNSS antenna is located forward or aft of the wings on the top of the fuselage.

(2) The installer must ensure that a 5 degree mask angle (or lower if the receiver installation instructions identify a lower mask angle) is provided by the installation. This includes consideration of antenna location and blockage, with the aircraft at typical cruising attitude. The antenna should also be located to minimize the effects of airplane shadowing during typical maneuvers.

Using the guidelines in the installation instructions, verif › The GNSS equipment installation instructions state that the

(3) The antenna should be separated as much as practical from transmitting antennas (e.g., VHF, TCAS, SATCOM, and HF). For small aircraft, the antenna should also be separated as much as practical from the windscreen to prevent case-to-antenna coupling.

(4) For installations on rotorcraft, the effects of the rotor blades on antenna performance must be considered.

(5) For multiple-sensor installations, the installer should reduce the likelihood that a single lightning strike affects all the sensors (i.e., do not place them in a straight line from the front to the rear of the fuselage).

b. Anti-Ice Protection. If the aircraft is approved for flight into known icing conditions, the antenna must not be susceptible to ice buildup (i.e., is installed in a nonicing location on the aircraft, or is of a sufficiently low profile that ice does not accumulate on the antenna). Alternatively, the equipment can be shown to operate satisfactorily when the antenna is subject to icing if there are no harmful effects of the ice build-up, such as possible ingestion into the engine of accumulated ice or degradation in aerodynamic performance. The effects of ice accumulation on the antenna, if any, can be found in the manufacturer's installation instructions. See AC 23.1419-2A and AC 25-1419-1 for additional guidance.

c. Antenna Cables. Double shielded cables should be used to prevent interference coupling into the cable.

d. Structure. Any modifications to the aircraft to install a new antenna need to be evaluated for their impact on aircraft structure. For specific guidance relating to modifications in the fuselage structure for Part 23 aircraft, see AC 23-5, Cutouts in a Modified Fuselage of Small Airplanes.

17. INSTALLATION ISSUES – GNSS SENSOR. This paragraph provides guidance related to the installation of a GPS sensor, including those sensors that integrate WAAS or LAAS. This paragraph also applies the installation of stand-alone navigation equipment, since that equipment has an embedded sensor. This guidance applies to all installations, but is only expected to be specifically evaluated as part of the initial airworthiness approval.

a. Antenna/Sensor Compatibility.

(1) Using the guidelines in the installation instructions, verify the antenna installation is compatible with the GNSS equipment. This may be accomplished by one of the following:

(i) The antenna (part number) is identified in the GNSS equipment installation instructions as compatible;

(ii) The GNSS equipment installation instructions state that the equipment is compatible with any standard, passive TSO-C144 antenna. In this case the antenna should have authorization to TSO-C144. Compare the RTCA/DO-160(AR) category for lightning-induced transients specified in the antenna installation instructions with the category defined in the receiver installation instructions; or

VHF Communications. Harmonic, spurious, and local oscillato › Replacing the VHF equipment.

(iii) The GNSS equipment installation instructions state that the equipment is compatible with any standard, active TSO-C144 antenna. A signal power budget must be defined that takes the output power at the low-noise amplifier of the antenna (as defined in the antenna installation instructions) and matches that to the receiver dynamic range and sensitivity (as defined in the GNSS equipment installation instructions). Compare the RTCA/DO-160(AR) category for lightning-induced transients specified in the antenna installation instructions with the category defined in the receiver installation instructions.

(2) Use the guidelines in the installation instructions when determining what cables and connectors to use to connect the antenna to the receiver, including cable lengths that result in acceptable loss of signal power.

(3) Ensure antenna and GNSS equipment compatibility for aircraft equipped with SATCOM. Some equipment may have been qualified to less stringent interference levels for aircraft installations without SATCOM.

b. Interference - Electromagnetic Compatibility (EMC).

(1) The equipment must not be the source of objectionable conducted or radiated interference or be adversely affected by conducted or radiated interference from other equipment or systems installed in the aircraft.

(2) Proper grounding of GNSS and other equipment is essential to ensuring EMC.

(3) When possible, do not install the sensor near a VHF radio.

(4) The following paragraphs identify potential sources of interference and means of mitigating that interference:

(i) SATCOM. Out-of-band SATCOM emissions and in-band intermodulation between multiple channel SATCOM installations can affect GNSS. GNSS equipment must not be installed in aircraft with multiple SATCOM channels unless the simultaneous use of interfering frequencies can either be prevented or demonstrated not to interfere with the operation of the GNSS equipment. Note that some equipment is not compatible with SATCOM installations at all, as noted in the installation instructions.

(ii) VHF Communications. Harmonic, spurious, and local oscillator harmonics from VHF equipment can cause interference to GNSS. Interference can be mitigated by:

(A) Installing filters at the output of the VHF transmitter to prevent antenna-to-antenna interference. Such filters should have an insertion loss of 2 dB or less, or the installed VHF transceiver performance will have to be re-evaluated.

(B) Installing the GNSS equipment as far away as feasible from any VHF transmitter equipment (to prevent case-to-case interference).

(C) Replacing the VHF equipment.

INSTALLATION ISSUES – STAND-ALONE NAVIGATION EQUIPMENT. Thi › GNSS Configuration Strapping. Often, GNSS equipment uses so

(iii) ELT. An ELT can re-radiate DME or VHF signals that can interfere with GPS. Notch filters on the ELT antenna cable or replacing the ELT can eliminate this problem.

(iv) DME. DME has been known to cause interference to GPS. Replacing the DME transceiver can eliminate the problem for some equipment.

(v) Direction Finding (DF) equipment. Moving the DF antenna to the belly of the aircraft has been found to eliminate this problem.

c. Interface Requirements. Ensure sensor compatibility for aircraft systems utilizing the position output (e.g. flight management system, automatic dependent surveillance system). Systems should use the same bus standard (e.g., ARINC 429 with ARINC 743 data, RS-232 with RTCA/DO-229 Appendix H data).

(1) Operation of the GNSS equipment must not adversely affect the performance of other aircraft equipment. Likewise, operation of the GNSS equipment must not interfere with the operation of other equipment installed in the aircraft.

(2) Additional information on interfacing a GNSS sensor with a multi-sensor system can be found in AC 20-130A.

(3) GNSS sensors may provide output to a variety of applications, including terrain awareness and warning systems (TAWS), automatic dependent surveillance (ADS), and moving map displays for situational awareness. The guidance material in this AC for sensors applies to all of these integrations, and should be used in conjunction with the guidance material for the application. For specific information relating to TAWS equipment, see TSO-C151a. GPS, GPS/WAAS, or GPS/LAAS position information may be used as the position determination as addressed in Appendix 1, paragraph 5 of TSO-C151a and paragraph 11 of AC 25-23. Guidance for electronic map displays can be found in RTCA/DO-257A, Minimum Operational Performance Standards for the Depiction of Navigation Information on Electronic Maps. Guidelines for interfacing with ADS-broadcast equipment can be found in RTCA/DO-242A, Minimum Aviation System Performance Standards for ADS-B. Failure of the GNSS equipment should not cause failure of the interfaced equipment.

d. GPS Equipment (with or without LAAS). Equipment that uses TSO-C129(AR) as the basis for the GPS functions has a limited ability to meet navigation requirements. This limitation should be documented in the A/RFM(S) as follows: “The aircraft must have other approved navigation equipment installed and operating appropriate to the route of flight”.

18. INSTALLATION ISSUES – STAND-ALONE NAVIGATION EQUIPMENT. This paragraph provides guidance related to the installation of stand-alone navigation equipment. In addition to the guidance in this paragraph, stand-alone navigation equipment incorporates an antenna and a sensor and should comply with the guidance in paragraphs 16 and 17 of this AC. This guidance applies to all installations, but is only expected to be specifically evaluated as part of the initial airworthiness approval.

a. GNSS Configuration Strapping. Often, GNSS equipment uses software configuration straps or installation set parameters entered either manually by the installer

INSTALLATION ISSUES – STAND-ALONE NAVIGATION EQUIPMENT. Thi › Source Selection. For installations where GNSS outputs can

or by using an Aircraft Personality Module (APM). These software configuration straps or parameters disable/enable functionality, configure the input/output formats, determine the displayed units of measure, and more. The software configuration programming documentation must become a part of the installation package and should be included in the Master Drawing List. When using an Approved Model List (see paragraph 8), multiple configurations may be specified.

b. General Human Factors Considerations.

(1) Control Accessibility. Controls installed for in-flight operation should be readily accessible from the pilot's seated position. Only single-hand operation should be required, the controls should be readily identifiable, and the use of controls should not obscure pertinent displays.

(2) Inadvertent Turnoff. System controls should be arranged to provide adequate protection against inadvertent system turnoff.

(3) Control/Display Visibility.

(i) The appropriate flight crew member(s) should have an unobstructed view of displayed data when in the seated position.

(ii) Compliance with limitations in the installation instructions for display readability should be verified.

(iii) All displays, controls, and annunciators must be easily readable under all normal cockpit conditions and expected ambient light conditions (total darkness to bright, reflected sunlight).

(4) Annunciations.

(i) Visual annunciations must be consistent with the criticality of the annunciation and must be readable under all normal cockpit illumination conditions. Visual annunciations must not be so bright or startling as to reduce pilot dark adaptation.

(ii) Audible alarms should be sufficiently loud and of appropriate pitch quality, duration and pattern. Alarms should be easily deactivated (but not easily deactivated inadvertently). Audible alarms must not interfere with other aircraft audio alarms or alerts of higher priority (e.g. stall warnings, gear warning, or chip-detect).

c. Source Selection. For installations where GNSS outputs can drive a display that is shared with other navigation equipment (e.g., VOR/DME, ILS, MLS), the pilot must be able to select the source of guidance, and the selected source must be clearly annunciated to the flightcrew, on or near the affected display. GNSS-based navigation (GPS, GPS/WAAS, GPS/LAAS) need not be differentiated. When applicable, annunciation of the selected source should be driven by the same relay switch to preclude erroneous information in case of switch failure. Autopilot operation should be inhibited if the displayed source is not the same as the source driving the autopilot. This is particularly critical for approach operations (i.e., autopilot in approach mode).

Synchronization. Synchronization refers to the ability for › The workload associated with manually updating both equipmen

d. Navigation Display.

(1) The horizontal (and vertical) deviation(s) display(s) and failure annunciation should be located within the pilot's primary field of view, as should any indication requiring immediate aircrew action. For the purpose of this AC, the primary field of view is within 15 degrees of the pilot’s primary line of sight.

(2) Displays used for loss of integrity monitoring, waypoint sequencing, start of a turn, turn anticipation, active waypoint, distance to active waypoint, desired track and actual track (track angle error), TO/FROM indication, approach mode annunciation, and automatic mode switching should be located within the pilot’s normal field of view. The normal field of view is such that the pilot would notice an annunciation during normal aircraft operation. Guidelines for the normal field of view include: the lateral normal field of view is from the center of the airspeed indicator to and including the equipment if installed in the center radio stack. Alternatively, if the equipment is installed to the left of the airspeed indicator, the lateral normal field of view is the center of the altimeter to and including the equipment. The vertical normal field of view includes immediately above and below the basic “T” instruments (may also be anywhere within the lateral field of view).

e. Failure Indications.

(1) It is important to install the equipment such that all failure conditions result in appropriate displays.

(2) For installations not incorporating an external navigation display (CDI, HSI, etc.), complete blanking of the Control Display Unit (CDU) display is acceptable.

(3) Presentation of a failure/status annunciation (flag or integrity annunciation) does not require removal of navigation information from the navigation display.

(4) A unique annunciation of the loss of integrity monitoring should be provided.

f. Dual GNSS Installations.

(1) Synchronization. Synchronization refers to the ability for control inputs to one RNAV equipment to automatically update the other equipment. Dual installations should be synchronized whenever possible to reduce crew workload and prevent confusion over which system/flight plan is driving the navigation data. If the Functional Hazard Assessment requires dual GNSS or is operationally required, then synchronization is required. If the navigation equipment are not synchronized, then the following issues should be evaluated:

(i) The pilot and co-pilot (if applicable) should be able to view and enter data in the offside equipment. This must not interfere with throttle levers, flap handle, etc.

(ii) The workload associated with manually updating both equipment to maintain consistency between them should be evaluated.

Intermixing of RNAV equipment. Where multiple RNAV systems › Database differences: Differences in the area navigation dat

(iii) There should be no possible confusion as to the equipment that is driving the autopilot and navigation displays.

(iv) Displays and annunciations should be evaluated for possible inconsistencies that result from differences in the equipment (e.g., different flight plans could result in one equipment going into approach mode while the other does not). These inconsistencies must not cause a misleading situation. These are of particular concern when the cockpit architecture allows for cross coupling (e.g. GNSS-2 switched to drive side 1 displays).

(2) Intermixing of RNAV equipment. Where multiple RNAV systems are intended to be used simultaneously (typically in two-pilot aircraft), installation of area navigation equipment with different crew interfaces can be very confusing and lead to problems since they may have conflicting methods of operation and conflicting display formats. There can be problems even when intermixing different versions of the same equipment. At a minimum, considerations should be given to the following potential incompatibilities, especially when the cockpit architecture allows for cross coupling (i.e. GNSS-2 switched to drive side 1 displays).

(i) Data entry: The equipment must have consistent methods of data entry, and similar pilot procedures for accomplishing common tasks. RTCA/DO-229C section 2.2.1.1.3 identifies a minimum set of common tasks that should be considered. Any differences should be evaluated for pilot workload. If the wrong procedures are used (the procedures for data entry on the offside are used), there must be no misleading information and it should be easy to identify and recover from the mistake.

(ii) CDI scaling: Sensitivity must be consistent or annunciated. Standalone navigation equipment that complies with RTCA/DO-229C will have consistent scaling provided the flight plans between the equipment are identical (see synchronization issues above).

(iii) Display symbology and mode annunciations: There should be no conflicting symbols or annunciations (e.g., a common symbol used for two different purposes), and differences should be specifically evaluated to evaluate the potential confusion they may cause.

(iv) Mode logic: The modes internal to the equipment and interfaced to the rest of the aircraft should be consistent.

(v) Equipment failure: The effect of failure of one equipment must not result in misleading information on the other equipment.

(vi) Displayed data: The display of primary navigation parameters (waypoint distance, bearing, desired track/actual track, track angle error, numeric crosstrack deviation) must use consistent units and a consistent notation. Any inconsistency in the display of the primary information should not be approved.

(vii) Database differences: Differences in the area navigation database and RNAV equipment response can result in contradictory guidance between two dissimilar types of RNAV equipment. A means of ensuring compatible updates between the equipment must be defined and documented in the operations manual or A/RFM(S).

INSTALLATION ISSUES – STAND-ALONE NAVIGATION EQUIPMENT. Thi › Interface to Magnetic/True Switch. If a MAG/TRUE heading ref

g. Interface to Flight Guidance System (FGS). This paragraph describes guidelines for interfacing the GNSS stand-alone navigation equipment with a flight guidance system. These issues may be addressed through operating limitations in the A/RFM(S). When used in this paragraph, the word “consistent” means that the installed GNSS equipment does not alter the cockpit design philosophy or intended function of an FGS mode, switch or annunciation.

(1) Connection to the autopilot must be consistent with the autopilot installation instructions and the GNSS installation instructions.

(2) Operational compatibility between the GNSS equipment and the FGS should be verified. Protection should exist in the GNSS or the FGS to keep the aircraft within the approved operational envelope (e.g. roll, pitch, speed, and altitude). See the relevant guidelines for the particular aircraft (e.g., AC 23-17A and AC 25.1329).

(3) A positive, continuous and unambiguous indication should be provided of the FGS modes actually in operation, as well as those that are armed for engagement. In addition, where engagement of a mode is automatic, clear indication must be given when the mode has been armed by either action of a member of the flight crew, or automatically by the system.

(4) The GNSS equipment must be compatible with the FGS modes of operation. For example the arm, engage and disengage sequence of the GNSS equipment should be consistent in the annunciation and engage/disengage timing of the FGS. This is particularly important during WAAS approaches, which include different levels of service (reference section 2.2.4.7.4 of RTCA/DO-229C).

(5) If the GNSS equipment is connected to a reduced bank selector, the GNSS bank angle, like the FGS, must not be limited by this switch selection during approach. Consistency in the operation must be maintained.

(6) Some aircraft operate in areas of the operational flight envelope where buffet onset can occur when normal maneuvering load factors are present (e.g. at higher altitudes). This is a concern, since the GNSS equipment can automatically sequence waypoints and initiate turn maneuvers which may or may not have the pilots attention. If buffet protection is not provided for in the GNSS or FGS (e.g. bank angle limiting, or limiting of cruise altitude based upon buffet margin), an A/RFM(S) limitation should be added to the performance section, prohibiting cruise operation at weight/altitude combinations that result in buffet margins less than 1.4g.

(7) For those aircraft that have incorporated bank angle limiting, consideration should be given to whether the GNSS equipment is defining a path that cannot be flown.

h. Interface to Magnetic/True Switch. If a MAG/TRUE heading reference switch is installed in the aircraft, the GNSS equipment should be driven by the same switch to maintain consistency in the displays and operation for both manual and automatic heading reference changes.

Performance Monitoring. Sufficient information must be prov › Indication of the position of the aircraft with respect to t

i. Interface to Barometric Altimeter.

(1) If there is an air data source select switch, when the pilot de-selects an air data source the de-selected source must no longer be used by the GNSS equipment. This becomes important for barometric-aided FDE, since erroneous altitude inputs to the FDE algorithm could lead to improper satellite detection and exclusion.

(2) If the GNSS equipment requires barometric corrected (or pressure) altitude data for certain operations (identified in the GNSS installation instructions), the installation should provide an automatic altitude input from the air data system to the GNSS such that additional pilot actions are not required.

(3) If barometric corrected altitude is required by the GNSS equipment and an automatic input of the barometric corrected altitude is not available, an alert for the pilot during approach must be provided indicating the need to enter the barometric pressure setting in the GNSS. If the equipment requires multiple entries to enter the correction, the workload should be evaluated during an approach.

19. INSTALLATION ISSUES – LPV AND GLS APPROACHES. This paragraph provides guidance related to the installation of WAAS and LAAS equipment supporting LPV or GLS approaches. This guidance applies to all installations, but is only expected to be specifically evaluated as part of the initial airworthiness approval. GNSS equipment intended for LPV or precision approach operation must provide for the following:

a. Update Rate. For sensors that support an LPV or precision approach capability (Class 3 equipment of TSO-C145a, LAAS equipment), the position used for the approach must be output at 5 Hz. If the TSO-C145a equipment provides a 1 Hz output, the installation must use inertial aiding or other method to obtain deviations at 5 Hz.

b. Differential Group Delay. If the GNSS equipment is installed with an antenna that has not previously been determined to be compatible, verify that the differential group delay of the antenna is less than or equal to the requirement for the receiver (as specified in RTCA/DO-229C, section 2.1.4.5). The differential group delay of the antenna will be documented in the installation instructions, and the requirement for differential group delay will be documented in the receiver installation instructions. Antennas have filters that could affect the delay. If the antenna instructions do not document the differential group delay, then the data should be obtained and found to be within the limits specified in the receiver installation instructions before approval can be given for approach operations.

c. Performance Monitoring. Sufficient information must be provided in the flight deck to allow the pilots to monitor the progress and safety of the approach operation. This in-flight performance monitoring must include:

(1) Unambiguous identification of the intended path for the approach, (e.g. LPV or GLS approach, identifier, frequency or channel number, and selected navigation source), and

(2) Indication of the position of the aircraft with respect to the intended path (e.g. cross track and vertical deviation information).

INSTALLATION ISSUES – LAAS VDB RECEIVER. This paragraph prov › VDB aircraft implementation loss. The aircraft implementati

d. System Status. The flight crew must have a means to evaluate the capability of the aircraft equipment to accomplish the low visibility operation prior to and after departure. The flight crew must be advised of failed aircraft systems or equipment affecting the decision to continue to the destination or divert to an alternate.

e. Annunciations. For installations containing more than one approach navigation source, the navigation source (e.g. ILS, GLS) selected for the approach must be positively indicated in the normal field of view at each pilot station.

f. Accessibility.

(1) Single equipment installations must be accessible and usable by the pilot. For aircraft requiring two crew members, the equipment should be accessible and usable by either pilot located at a pilot or copilot crew station.

(2) Dual (or more) equipment installations must have a convenient and expedient way to update data, information and programs, and a means to ensure consistency between the equipment (e.g., a “crossload” capability can ensure identical data) (also addressed under paragraph 18f for stand-alone navigation equipment).

20. INSTALLATION ISSUES – LAAS VDB RECEIVER. This paragraph provides guidance related to the installation of a VDB receiver, including those embedded within a multi-mode receiver. This guidance applies to all installations, but is only expected to be specifically evaluated as part of the initial airworthiness approval.

a. Interference – EMC. The VDB receiver may be susceptible to interference from VHF communications equipment on the aircraft.

Continue reading ↓ 120 of 186 passages shown