AC 27-1B Certification of Normal Category Rotorcraft (Changes 1 - 9 incorporated)
a.This revision makes needed changes to this Advisory Circular (AC). b.The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
Text read by OCR from a scanned file (8 of 1196 pages). Check the original, as some words may be misread.
TIPS ON USING BOOKMARKS IN THIS DOCUMENT
We have added a new feature that should help you to move around more quickly in the advisory circular.
On the upper left side, click on “Bookmarks.” You can click on any line that has a plus sign (+) beside it and it will expand to show you everything that comes under that particular section. You can click on any bookmark and you will go directly to that paragraph.
lllgblly slgral b)' VICTOR W WICKLUND o.1D: 2023.08.23 16;38;31 -04'00'
6/23/23
Advisory U.S. Department of Transportation Federal Aviation Circular Administration
Subject: Certification of Normal Category Date: AC No: 27-1B Rotorcraft Initiated By: AIR-600 Change: 9
1. PURPOSE.
a. This revision makes needed changes to this Advisory Circular (AC).
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
2. PRINCIPAL CHANGES.
This Change 9 includes changes, edits, and additions for these AC sections: 27.87, 27.903, 27.1305, 27.1309, 27.1329, 27.1335, 27.1353, 27.1543, 27.1545, 27.1549, 27.1555, 27.1587, AC 27 Appendix B.
The contents of this guidance document do not have the force and effect of law and are not meant to bind the public in any way. This guidance document is intended only to provide clarity to the public regarding existing requirements under the law or agency policies.
3. WEBSITE AVAILABILITY.
To access this AC electronically, you can go to either of the following sites:
http://www.faa.gov/regulations_policies/advisory_circulars/
https://drs.faa.gov/browse
Victor Wicklund, Acting Director, Policy & Standards Division Aircraft Certification Service
Advisory U.S. Department of Transportation Circular Federal Aviation Administration
Subject: Certification of Normal Category Date: 06/29/2018 AC No: 27-1B Rotorcraft Initiated By: AIR-680 Change: 8
1. PURPOSE.
a. This Advisory Circular (AC) publishes needed changes to the existing Advisory Circular (AC) material.
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
2. PRINCIPAL CHANGES. This change 8 includes changes, edits, and additions for section 27.773.
PAGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
D-63 thru D-66 9/30/1999 D-63 thru D-66 06/29/18
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
Dr. Michael C. Romanowski Director, Policy and Innovation Division Aircraft Certification Service
0 Advisory
U.S. Departmen1 ofTransportation Circular Federal Aviation
Ad,nlnistrotton
Subject: CERTIFICATION OF NORMAL Date: FEB 4 2016 AC No: 27-1B CATEGORY ROTORCRAFT Initiated by: ASW-1 IO Cban~e: 7
1. PURPOSE.
a. This change publishes needed changes to the existing material and adds Miscellaneous Guidance (MG) sections to the Advisory Circular (AC).
b. The change number and the date ofthe changed material are shown at the top ofeach page. The vertical lines in the outside margin indicate the beginning and end ofeach change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
2. PRINCIPAL CHANGES.
a. This change 7 includes changes, edits, and additions for these AC sections: 27.865B, 27.1321. 27 MG 1, 27 MG 16, and 27 Appendix B.
b. This change adds to this AC ihe following MG sections: AC 27 MG 19 (Guidance on Electronic Display Systems (EDS) for Rotorcraft Installations), AC 27 MG 20 (Human Factors (HF)), and AC 27 MG 21 (Guidance on Creating a System Level Functional Hazard Assessment (FHA)).
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory
Aircraft Certification Service
Circular 1library at http://www·.faa.gov/regulations policies/advisory circulars/.
f~ a , Rotorcraft Directorate,
U.S. Deportment of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF NORMAL Date: 7/25/2014 AC No: 27-1B CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 6
1. PURPOSE.
a. This Advisory Circular (AC) change publishes the new guidance on automatic flight guidance and control systems (AFGCS) installation in part 27 rotorcraft.
b. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES. This change adds the miscellaneous guidance section 23 (MG 23), Automatic Flight Guidance and Control Systems (AFGCS) Installation in Part 27 Rotorcraft., to the AC.
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
/s/ Lance T. Gant, for Kim Smith Manager, Rotorcraft Directorate, Aircraft Certification Service
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF NORMAL Date: 6/13/2014 AC No: 27-1B CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 5
1. PURPOSE.
a. This Advisory Circular (AC) change publishes the new guidance on analyzing an advanced flight controls (AdFC) system installation in normal category rotorcraft.
b. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES. This change adds the miscellaneous guidance section 17 (MG 17), Guidance on Analyzing an Advanced Flight Controls (AdFC) System, to the AC.
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
/s/ Kim Smith Kim Smith Manager, Rotorcraft Directorate, Aircraft Certification Service
AC 27.1B, Chg 4 5/1/2014 Advisory Circular
U.S Deportment of Transportation
Federal AvkJtion Administration
Subject: CERTIFICATION OF NORMAL Date: 5/1/2014 AC No: 27-1B CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 4
1. PURPOSE.
a. This Advisory Circular (AC) publishes needed changes to the existing AC material. Additionally, there is incorporation of previously approved AC material and non-technical editorial changes to various sections.
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
c. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES.
a. The AC sections previously approved on September 17, 2009 and posted separately to the Regulatory and Guidance Library (RGL), which are related to the Rotorcraft Performance and Handling Qualities rulemaking, are incorporated in this change 4. Those AC sections that were added or changed are: 27.25A, 27.49, 27.51A, 27.71, 27.73, 27.75A, 27.79, 27.87, 27.143A, 27.173A, 27.175A, 27.177A, 27.903B, 27.1587A, and 27 Appendix B.
b. The changed AC 27 Miscellaneous Guidance (MG) 5 section (Agricultural Dispensing Equipment Installation), previously approved on December 15, 2009 and posted separately to the Regulatory and Guidance Library (RGL), is incorporated in this change 4.
c. The AC 27.573 section previously approved on December 1, 2011 and posted separately to the Regulatory and Guidance Library (RGL), which is related to the Damage Tolerance and Fatigue Evaluation of Composite Rotorcraft Structures rulemaking, is incorporated in this change 4.
Page ii
d. The changed AC 27 MG 6 section (Emergency Medical Service (EMS) Systems Installations Including: Interior Arrangements, Equipment, Helicopter Terrain Awareness and Warning System (HTAWS), Radio Altimeter, and Flight Data Monitoring System), previously approved on February 27, 2014, is incorporated in this change 4.
e. The changed AC 27 MG 18 section (Helicopter Terrain Awareness and Warning System (HTAWS)), previously approved on February 27, 20014, is incorporated in this change 4.
f. This change 4 also includes changes, edits, and additions for these AC sections: 27.29, 27.45, 27.75, 27.79, 27.141, 27.143, 27.151, 27.337, 27.351, 27.561, 27.562, 27.610, 27.783, 27.863, 27.865, 27.865B, 27.871, 27.903B, 27.939, 27.1011, 27.1093, 27.1093A, 27.1187, 27.1309, 27.1316, 27.1317, 27.1329, 27.1337, 27.1357, 27.1435. 27.1501, 27.1543, 27.1549, 27 MG 8, 27 MG 10, 27 MG 13, and 27 MG 22.
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
/s/ Lance T. Gant, for Kim Smith Manager, Rotorcraft Directorate, Aircraft Certification Service
Page iii
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF NORMAL Date: 9/30/2008 AC No: 27-1B CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 3
1. PURPOSE.
a. This Advisory Circular (AC) publishes needed changes to the existing AC material as a result of a safety-focused study.
b. This change revises existing material in 6 sections.
c. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the right or left margin indicates the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
d. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES. Sections 27.571, 27.679, 27.695, 27.783, 27.901A, and 27.1351 are revised.
3. WEBSITE AVAILABILITY. To access this AC electronically, log on to http://www.airweb.faa.gov/rgl and then click on AC’s.
AC 27.1B, Chg 4 5/1/2014
AC 27-1B, Chg 3 PAGE CONTROL CHART
Remove Pages Dated
v thru xii … 9/30/99 & 4/25/06 C-83 thru C-87 … 9/30/99 & 2/12/03 D-39 thru D-40 … 9/30/99 D-45 thru D-46 … 9/30/99 D-71 thru D-72 … 9/30/99 E-5 thru E-6 … 9/30/99 F-53 thru F-56 … 9/30/99
Signed by Scott A. Horn for
Mark R. Schilling Acting Manager, Rotorcraft Directorate
Aircraft Certification Service
Insert Pages Dated
v thru xii … 9/30/99, 4/25/06, & 9/30/08 C-83 thru C-88 … 9/30/08 D-39 thru D-40.2 … 9/30/08 D-45 thru D-46 … 9/30/99 & 9/30/08 D-71 thru D-72.2 … 9/30/99 & 9/30/08 E-5 thru E-6 … 9/30/08 F-53 thru F-56 … 9/30/08
Page ii
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
…
Subject: CERTIFICATION OF NORMAL Date: 4/25/06 AC No: 27-1B CATEGORY ROTORCRAFT Initiated ASW-110 Change 2
1. PURPOSE.
a. This change incorporates all the previously revised AC paragraphs that were posted as accepted and finalized AC material on the FAA RGL website since 2/12/03.
b. This change revises existing material in 13 paragraphs and adds new material for one paragraph.
c. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the right and left margins indicate the beginning and end of each change. Pages that have different page numbers but no text changes will retain the previous heading information.
d. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES.
a. Paragraphs 27.351, 27.602, 27.672, 27.683, 27.777, 27.1321, 27.1585, MG 1, MG 4, MG 8, MG 16, Appendix A, and Appendix B are revised.
b. The AC material in MG 12 has been revised by a working group and is now contained in AC 27.865B, in Subpart D.
c. New paragraph MG 18, Helicopter Terrain and Awareness Systems (HTAWS), is added to Chapter 3.
d. New figure AC 27.351-2 is added in Chapter 2.
e.New figures AC 27 MG 8-1, MG 8-2, MG 8-3, MG 8-4, MG 18-1, MG 18-2, and MG 18 2.1 are added in Chapter 3.
3. WEBSITE AVAILABILITY. To access this AC electronically, log on to http://www.airweb.faa.gov/rgl and then click on AC’s.
I
I I
AC 27.1B, Chg 4 5/1/2014
AC 27-1B, Chg 2 PAGE CONTROL CHART Remove pages Dated v thru x … 9/30/99 & 2/12/03 xiii thru xxi … 2/12/03 C-9 thru C-86 … 9/30/99 & 2/12/03 D-1 thru D-58 … 9/30/99 & 2/12/03 D-67 thru D-70 … 9/30/99 D-109 thru D-112 … 9/30/99 & 2/12/03 F-33 thru F-46 … 9/30/99 G-43 thru G-48 … 9/30/99 MG 1-15 thru MG 1-17 … 9/30/99 MG 4-9 thru MG 4-13 … 9/30/99 MG 8-1 thru MG 8-15 … 9/30/99 & 2/12/03 MG 12-1 thru MG 12-42... 9/30/99 & 2/12/03 MG 16-1 thru MG 16-16 … 2/12/03 none none Apdx A-47 thru Apdx A-70 … 2/12/03 Apdx B-11 thru Apdx B-20 … 9/30/99
David A. Downey Manager, Rotorcraft Directorate
Aircraft Certification Service
Insert Pages Dated v thru x … 4/12/06 xiii thru xxii … 4/12/06 C-9 thru C-87 … 4/12/06 D-1 thru D-58 … 4/12/06 D-67 thru D-70 … 4/12/06 D-109 thru D-133 … 4/12/06 F-33 thru F-46 … 4/12/06 G-43 thru G-49 … 4/12/06 MG 1-15 thru MG 1-16 … 4/12/06 MG 4-9 thru MG 4-13 … 4/12/06 MG 8-1 thru MG 8-31 … 4/12/06 MG 12-1 … 4/12/06 MG 16-1 thru MG 16-18 … 4/12/06 MG 17-1 … 4/12/06 MG 18-1 thru MG 18-27 … 4/12/06 Apdx A-47 thru Apdx A-71 … 4/12/06 Apdx B-11 thru Apdx B-20 … 4/12/06
Page ii
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF NORMAL Date: 2/12/03 AC No: 27-1B CATEGORY ROTORCRAFT Initiated ASW-110 Change 1 … 1. PURPOSE.
a. This change revises existing material in 17 paragraphs and adds new material for 12 paragraphs.
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the right and left margins indicate the beginning and end of each change. Pages that have different page numbers but no text changes will retain the previous heading information.
2. CANCELLATION.
a. AC 20-95, Fatigue Evaluation of Rotorcraft Structure, May 18, 1976, is canceled in its entirety, and is replaced by material contained in AC 27 MG 11.
b. AC 20-137, Dynamic Evaluation of Seat Restraint Systems & Occupant Restraint for Rotorcraft (Normal and Transport), March 30, 1992, is canceled in its entirety, and is replaced by material contained in AC 27.562.
c. AC text containing references to AC 20-95 and AC 20-137 was either changed or deleted in paragraphs AC 27.2, 27.562, 27.613, 27.785A, 27.865A, 27.907, 27.952, MG 8, and MG 12.
3. PRINCIPAL CHANGES.
a. Paragraphs 27.562, 27.571, 27.1303, 27.1353, 27.1419, 27.1505, 27.1529, MG 5, MG 6, and MG 12 are revised.
b. New paragraphs 27.610A, 27.625A, 27.785B, 27.805, 27.807B, and 27.853A are added to Chapter 2.
c. New paragraphs MG 11, MG 13, MG 14, MG 15, and MG 16 are added to Chapter 3.
f. Appendix A (previously reserved) is added.
g. New figures AC 27.562-1, 27.562-2, 27.562-3, 27.562-4, 27.562-5, 27.562-6, 27.562-7, and 27.562-8 are added in Chapter 2.
h. New figures AC 27 MG 11-1, 11-2, 11-3, 11-4, 11-5, 11-6, 11-7, 11-8, 11-9, and AC 27 MG 14-1 are added in Chapter 3.
AC 27.1B, Chg 4 5/1/2014
4. WEBSITE AVAILABILITY. To access this AC electronically, log on to http://www.airweb.faa.gov/rgl and then click on AC’s.
AC 27-1B, Chg 1 PAGE CONTROL CHART Remove pages Dated iii thru xix … 9/30/99 A-3 thru A-4 … 9/30/99 C-43 thru C-50 … 9/30/99 D-7 thru D-105 … 9/30/99 E-9 thru E-10 … 9/30/99 E-31 thru E-32 … 9/30/99 E-39 thru E-44 … 9/30/99 F-1 thru F-91 … 9/30/99 G-3 thru G-47 … 9/30/99 MG 5-3 thru MG 5-6 … 9/30/99 MG 6-5 thru MG 6-16 … 9/30/99 MG 8-5 thru MG 8-6 … 9/30/99 none MG 12-21 thru MG 12-24 … 9/30/99 MG 12-37 thru MG 12-38 … 9/30/99 none none none none none
David A. Downey Manager, Rotorcraft Directorate
Aircraft Certification Service
Insert Pages Dated iii thru xxi … 2/12/03 A-3 thru A-4 … 2/12/03 C-43 thru C-86 … 2/12/03 D-7 thru D-112 … 2/12/03 E-9 thru E-10 … 2/12/03 E-31 thru E-32 … 2/12/03 E-39 thru E-44 … 2/12/03 F-1 thru F-102 … 2/12/03 G-3 thru G-48 … 2/12/03 MG 5-3 thru MG 5-6 … 2/12/03 MG 6-5 thru MG 6-16 … 2/12/03 MG 8-5 thru MG 8-6 … 2/12/03 MG 11-1 thru MG 11-28 … 2/12/03 MG 12-21 thru MG 12-24 … 2/12/03 MG 12-37 thru MG 12-38 … 2/12/03 MG 13-1 thru MG 13-8 … 2/12/03 MG 14-1 thru MG 14-8 … 2/12/03 MG 15-1 thru MG 15-18 … 2/12/03 MG 16-1 thru MG 16-16 … 2/12/03 Apdx A-1 thru Apdx A-70 … 2/12/03
Page ii
0 Advisory Circular
…
U.S. Department of Transportation
Federal Aviation Administration
Subject: CERTIFICATION OF NORMAL Date: 9/30/99 AC No: 27-1B CATEGORY ROTORCRAFT Initiated by: ASW-110 Change:
1. PURPOSE:
a. This is a total revision of AC 27-1A dated 7/30/97, with Change 1 dated 9/30/98, incorporated. In addition, new material plus changes to existing paragraphs are incorporated. This consolidated version is now renumbered as AC 27-1B and replaces AC 27-1A in its entirety. This revises existing material in 10 paragraphs, adds new material for three paragraphs, and renumbers paragraphs to correspond with Federal Aviation Regulations (FAR) numbering.
b. Requests from the rotorcraft industry to make the document easier to use resulted in renumbering the AC paragraphs to correspond with FAR numbering. The figure numbers are also renumbered accordingly.
c. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
d. This advisory circular provides information on methods of compliance with 14 CFR Part 27, which contains the Airworthiness Standards for Normal Category Rotorcraft. It includes methods of compliance in the areas of basic design, ground tests, and flight tests.
2. CANCELLATION. AC 27-1A, Certification of Normal Category Rotorcraft, dated 7/30/97, is canceled in its entirety.
3. BACKGROUND. Based largely on precedents set during rotorcraft certification programs spanning over 40 years, this AC consolidates guidance contained in earlier correspondence among FAA headquarters, foreign authorities, the rotorcraft industry, and certificating regions.
4. PRINCIPAL CHANGES:
a. Chapter 3 is now titled "Miscellaneous Guidance (MG), Normal Category Rotorcraft," with the following changes:
• Paragraphs that correspond to a FAR number are merged into existing AC text in Chapter 2.
AC 27.1B, Chg 4 5/1/2014
• Paragraphs that do not correspond with a FAR number either remain in Chapter 3 and are renumbered as MG paragraphs, or are now an appendix.
• In order to stay aligned with FAR numbering, Appendices A and C are reserved for future AC material. b. Paragraphs revised to incorporate technical guidance are AC 21.35, 27.561, 27.952, 27.1305, 27.1309, 27.1351, 27.1353, MG 2, and MG 4 (FADEC). AC 27.661, Rotorblade Clearance, contains new material added as a result of National Transportation Safety Board (NTSB) recommendations.
c. New paragraphs added are AC 27.1B and 27.2A, Gross Weight; AC 27.602, Critical Parts; and AC MG 12, External Loads. These paragraphs correspond with recent harmonized regulatory changes.
d. The AC is now divided by Subparts and page numbers reflect the relevant FAR Subpart.
e. “FAA/AUTHORITY” as used in this document means FAA or another airworthiness authority that has adopted this AC as a means of compliance with the appropriate regulation referenced.
5. DEVIATIONS. As rotorcraft designs vary from conventional configurations, it may become necessary to deviate from the methods and procedures outlined in this AC. These procedures are only one acceptable means of compliance with Part 27. Any alternate means proposed by an applicant will be given due consideration. Applicants are encouraged to use their technical ingenuity and resourcefulness to develop more efficient and less costly methods of achieving the objectives of Part 27. Regulatory personnel and designees should respond to such efforts by the use of engineering judgment in fostering any such efforts as long as the letter and spirit of Part 27 and the Federal Aviation Act are respected. It is recommended that unusual or unique projects be coordinated a sufficient time in advance with the Rotorcraft Standards Staff, ASW-110, or with the appropriate airworthiness authority, to ensure timely and uniform consideration.
6. APPLICABILITY. This material is not to be construed as having any legally binding status and must be treated as advisory only. However, to ensure standardization in the certification process, these procedures should be considered during all rotorcraft type certification and supplemental type certification activities.
7. PARAGRAPHS KEYED TO FAR PART 27. Each paragraph has the applicable amendment to Part 27 shown in the title. All of the original guidance material has been retained as appropriate, even as changes are made to the regulations. This is accomplished through the use of “A,” “B,” etc., paragraphs that follow the original numbered paragraphs. These subsequent paragraphs provide updated guidance information or changes to policy that parallel a specific rule change. The guidance material in the original paragraph (for earlier amendments) still applies and is modified as explained in each of the later paragraphs for later amendments. The applicable amendment number will only appear in the title line for the “A,” “B,” etc., paragraphs. The guidance material in the initial paragraph is intended to apply to all amendments except as modified by the later paragraphs. Each ensuing “A,” “B,” etc., paragraph will be identified with an amendment level to indicate the rule change that precipitated the policy change.
Page ii
8. RELATED PUBLICATIONS. FAA Certification personnel and designees should be familiar with Order 8110.4, Type Certification, and Order 8100.5, Aircraft Certification Directorate Procedures.
Eric Bries Acting Manager, Rotorcraft Directorate
Aircraft Certification Service
Page iii
5/1/2014 AC 27.1B, Chg 4
CONTENTS
Page No.
CHAPTER 1 - PART 21 CERTIFICATION PROCEDURES FOR
PRODUCTS AND PARTS
AC 21.16 Special Conditions … FAR 21-1 AC 21.31 Type Design … FAR 21-2 AC 21.33 Inspection and Tests … FAR 21-2 AC 21.35 Flight Tests … FAR 21-2 AC 21.39 Flight Test Instrument Calibration and Correction Report … FAR 21-6
CHAPTER 2 - PART 27 AIRWORTHINESS STANDARDS:
NORMAL CATEGORY ROTORCRAFT
SUBPART A
GENERAL
AC 27.1 Applicability … A-1 AC 27.1A Applicability … A-1 AC 27.1B Applicability … A-2 AC 27.2 Special Retroactive Requirements … A-2 AC 27.2A Special Retroactive Requirements … A-4
SUBPART B - FLIGHT
GENERAL
AC 27.21 Proof of Compliance … B-1 AC 27.25 Weight Limits … B-3 AC 27.25A Weight Limits … B-4 AC 27.27 Center of Gravity Limits … B-4.2 AC 27.29 Empty Weight and Corresponding Center of Gravity … B-6.2 AC 27.31 Removable Ballast … B-7 AC 27.33 Main Rotor Speed and Pitch Limits … B-7
PERFORMANCE
AC 27.45 Performance - General … B-9 AC 27.45A General … B-18 AC 27.45B General … B-18 AC 27.45C Performance – General … B-18
Page No.
Page iii
AC 27.1B, Chg 9 6/23/23
AC 27.49 Performance at Minimum Operating Speed … B-24.2 AC 27.51 Takeoff … B-25 AC 27.51A Takeoff … B-26 AC 27.65 AC 27.65A AC 27.67 AC 27.71 AC 27.73 AC 27.75 AC 27.75A AC 27.79 AC 27.79A AC 27.87 AC 27.87A
AC 27.141 AC 27.143 AC 27.143A AC 27.151 AC 27.161 AC 27.171 AC 27.173 AC 27.173A AC 27.175 AC 27.175A AC 27.177 AC 27.177A
AC 27.231 AC 27.235 AC 27.239 AC 27.241
AC 27.251
Page iv
SUBPART B - FLIGHT (continued)
PERFORMANCE (continued)
Climb: All Engines Operating … B-26.2 Climb: All Engines Operating … B-28 Climb: One Engine Inoperative … B-28 Autorotation Performance … B-29 Performance at Minimum Operating Speed … B-32 Landing … B-34.1 Landing … B-35 Limiting Height - Speed Envelope … B-37 Limiting Height - Speed Envelope … B-45 Height-Speed Envelope … B-45 Height-Velocity Envelope … B-45.1
FLIGHT CHARACTERISTICS
Flight Characteristics - General … B-46 Controllability and Maneuverability … B-48 Controllability and Maneuverability … B-52.2 Flight Controls … B-52.8 Trim Control … B-53 Stability: General … B-53 Static Longitudinal Stability … B-54 Static Longitudinal Stability … B-55 Demonstration of Static Longitudinal Stability … B-58 Demonstration of Static Longitudinal Stability … B-60.2 Static Directional Stability … B-60.6 Static Directional Stability … B-60.7
GROUND AND WATER HANDLING CHARACTERISTICS
Ground and Water Handling Characteristics - General … B-61 Taxiing Condition … B-61 Spray Characteristics … B-62 Ground Resonance … B-63
MISCELLANEOUS FLIGHT REQUIREMENTS
Vibration … B-68
5/1/2014 AC 27.1B, Chg 4
Page No.
SUBPART C - STRENGTH REQUIREMENTS
GENERAL
AC 27.301 Loads … C-1 AC 27.303 Factor of Safety … C-1 AC 27.305 Strength and Deformation … C-2 AC 27.307 Proof of Structure … C-2
AC 27.307A Proof of Structure … C-3 AC 27.309 Design Limitations … C-4
FLIGHT LOADS
AC 27.321 Flight Loads - General … C-5 AC 27.337 Limit Maneuvering Load Factor … C-5 AC 27.339 Resultant Limit Maneuvering Loads … C-8 AC 27.341 Gust Loads … C-8 AC 27.351 Yawing Conditions … C-9 AC 27.361 Engine Torque … C-14
CONTROL SURFACE AND SYSTEM LOADS
AC 27.391 Control Surface and System Loads - General … C-15 AC 27.391A Control Surface and System Loads - General … C-15 AC 27.395 Control System … C-15 AC 27.395A Control System … C-17 AC 27.397 Limit Pilot Forces and Torques … C-17 AC 27.399 Dual Control System … C-18 AC 27.401 Auxiliary Rotor Assemblies … C-18 AC 27.401A Auxiliary Rotor Assemblies … C-20 AC 27.403 Auxiliary Rotor Attachment Structure … C-20 AC 27.403A Auxiliary Rotor Attachment Structure … C-21 AC 27.411 Ground Clearance: Tail Rotor Guard … C-21 AC 27.413 Stabilizing and Control Surfaces … C-22 AC 27.413A Stabilizing and Control Surfaces … C-24 AC 27.427 Unsymmetrical Loads … C-24
GROUND LOADS
AC 27.471 Ground Loads - General … C-28 AC 27.473 Ground Loading Conditions and Assumptions … C-28 AC 27.475 Tires and Shock Absorbers … C-29 AC 27.477 Landing Gear Arrangement … C-29
Page v
AC 27.1B, Chg 4 5/1/2014
Page No.
SUBPART C - STRENGTH REQUIREMENTS (continued)
GROUND LOADS (continued)
AC 27.479 Level Landing Conditions … C-29 AC 27.481 Tail-Down Landing Conditions … C-30 AC 27.483 One-Wheel Landing Conditions … C-31 AC 27.485 Lateral Drift Landing Conditions … C-31 AC 27.493 Braked Roll Conditions … C-32 AC 27.497 Ground Loading Conditions: Landing Gear With Tail Wheels … C-32 AC 27.501 Ground Loading Conditions: Landing Gear With Skids … C-34 AC 27.501A Ground Loading Conditions: Landing Gear With Skids … C-35 AC 27.505 Ski Landing Conditions … C-35
WATER LOADS
AC 27.521 Float Landing Conditions … C-37
MAIN COMPONENT REQUIREMENTS
AC 27.547 Main Rotor Structure … C-38 AC 27.549 Fuselage, Landing Gear, and Rotor Pylon Structure … C-38
EMERGENCY LANDING CONDITIONS
AC 27.561 Emergency Landing Conditions - General … C-40 AC 27.561A Emergency Landing Conditions - General … C-41 AC 27.561B Emergency Landing Conditions - General … C-42 AC 27.561C Emergency Landing Conditions - General … C-43 AC 27.562 Emergency Landing Dynamic Conditions … C-44 AC 27.563 Structural Ditching Provisions … C-81 AC 27.563A Structural Ditching Provisions … C-81
FATIGUE EVALUATION
AC 27.571 Fatigue Evaluation of Flight Structure … C-83 AC 27.571A Fatigue Evaluation of Flight Structure for Category A Certification ... C-86 AC 27.573 Damage Tolerance and Fatigue Evaluation of Composite … C-88
Rotorcraft Structures
Page vi
5/1/2014 AC 27.1B, Chg 4
Page No.
SUBPART D - DESIGN AND CONSTRUCTION
GENERAL
AC 27.601 Design … D-1 AC 27.602 Critical Parts … D-2 AC 27.603 Materials … D-4 AC 27.605 Fabrication Methods … D-4 AC 27.607 Fasteners … D-6 AC 27.609 Protection of Structure … D-6 AC 27.610 Lightning Protection … D-8 AC 27.611 Inspection Provisions … D-11 AC 27.613 Material Strength Properties and Design Values … D-13 AC 27.613A Material Strength Properties and Design Values … D-14 AC 27.619 Special Factors … D-16 AC 27.621 Casting Factors … D-17 AC 27.623 Bearing Factors … D-27 AC 27.625 Fitting Factors … D-28 AC 27.625A Fitting Factors … D-29 AC 27.629 Flutter … D-29
ROTORS
AC 27.653 Pressure Venting and Drainage of Rotor Blades … D-31 AC 27.659 Mass Balance … D-31 AC 27.661 Rotor Blade Clearance … D-31 AC 27.663 Ground Resonance Prevention Means … D-33 AC 27.663A Ground Resonance Prevention Means … D-35
CONTROL SYSTEMS
AC 27.671 Control Systems - General … D-36 AC 27.672 Stability Augmentation, Automatic, and Power-Operated Systems... D-36 AC 27.673 Primary Flight Control … D-37 AC 27.674 Interconnected Controls … D-37 AC 27.675 Stops … D-38 AC 27.679 Control System Locks … D-40 AC 27.681 Limit Load Static Tests … D-40.1 AC 27.683 Operation Tests … D-41 AC 27.685 Control System Details … D-41 AC 27.685A Control System Details … D-42 AC 27.687 Spring Devices … D-43 AC 27.691 Autorotation Control Mechanism … D-43 AC 27.695 Power Boost and Power-Operated Control System … D-44
Page vii
AC 27.1B, Chg 4 5/1/2014
Page No.
SUBPART D - DESIGN AND CONSTRUCTION (continued)
LANDING GEAR
AC 27.723 Shock Absorption Tests … D-47 AC 27.725 Limit Drop Test … D-50 AC 27.727 Reserve Energy Absorption Drop Test … D-50 AC 27.727A Reserve Energy Absorption Drop Test … D-51 AC 27.729 Retracting Mechanism … D-51 AC 27.731 Wheels … D-54 AC 27.733 Tires … D-55 AC 27.735 Brakes … D-56 AC 27.737 Skis … D-58
FLOATS AND HULLS
AC 27.751 Main Float Buoyancy … D-59 AC 27.753 Main Float Design … D-60 AC 27.755 Hulls … D-60
PERSONNEL AND CARGO ACCOMMODATIONS
AC 27.771 Pilot Compartment … D-62 AC 27.773 Pilot Compartment View … D-63 AC 27.775 Windshields and Windows … D-68 AC 27.775A Windshields and Windows … D-68 AC 27.777 Cockpit Controls … D-68 AC 27.779 Motion and Effect of Cockpit Controls … D-69 AC 27.783 Doors … D-72.2 AC 27.783A Doors … D-74 AC 27.785 Seats, Berths, Safety Belts, and Harnesses … D-74 AC 27.785A Seats, Berths, Safety Belts, and Harnesses … D-78 AC 27.785B Seats, Berths, Litters, Safety Belts, and Harnesses … D-80 AC 27.787 Cargo and Baggage Compartments … D-80 AC 27.787A Cargo and Baggage Compartments … D-82 AC 27.801 Ditching … D-82 AC 27.805 Flight Crew Emergency Exits … D-91 AC 27.807 Emergency Exits … D-91 AC 27.807A Emergency Exits … D-93 AC 27.807B Emergency Exits … D-93 AC 27.831 Ventilation … D-94 AC 27.833 Heaters … D-96
Page viii
AC 27-1B, Chg 9
AC 27.853 AC 27.853A AC 27.855 AC 27.859 AC 27.861 AC 27.861A AC 27.863
AC 27.865 AC 27.865A AC 27.865B
AC 27.871 AC 27.873
AC 27.901 AC 27.901A AC 27.903 AC 27.903A AC 27.903B AC 27.903C AC 27.907
AC 27.917 AC 27.921 AC 27.923 AC 27.923A AC 27.923B AC 27.927 AC 27.927A AC 27.931
Page No.
SUBPART D - DESIGN AND CONSTRUCTION (continued)
FIRE PROTECTION
Compartment Interiors … D-98 Compartment Interiors … D-99 Cargo and Baggage Compartments … D-99 Heating Systems … D-101 Fire Protection of Structure, Controls, and Other Parts … D-105 Fire Protection of Structure, Controls, and Other Parts … D-106 Flammable Fluid Fire Protection … D-107
EXTERNAL LOADS
External Load Attaching Means … D-109 External Load Attaching Means … D-110 External Loads (previously MG 12) … D-111
MISCELLANEOUS
Leveling Marks … D-133 Ballast Provisions … D-133
SUBPART E - POWERPLANT
GENERAL
Installation … E-1 Installation … E-5 Engines … E-5.2 Engines … E-7 Engines … E-9 Engines … E-10.1 Engine Vibration … E-10.1a
ROTOR DRIVE SYSTEM
Design … E-10.2 Rotor Brake … E-11 Rotor Drive System and Control Mechanism Tests … E-12 Rotor Drive System and Control Mechanism Tests … E-17 Rotor Drive System and Control Mechanism Tests … E-18 Additional Tests … E-19 Additional Tests … E-21 Shafting Critical Speeds … E-21
Page ix
6/23/23
Page No.
SUBPART E – POWERPLANT (continued)
ROTOR DRIVE SYSTEM (continued)
AC 27.935 Shafting Joints … E-26 AC 27.939 Turbine Engine Operating Characteristics … E-26
FUEL SYSTEM
AC 27.951 Fuel System - General … E-29 AC 27.952 Fuel System Crash Resistance … E-31 AC 27.953 Fuel System Independence … E-56 AC 27.954 Fuel System Lightning Protection … E-57 AC 27.955 Fuel Flow … E-58 AC 27.955A Fuel Flow … E-62 AC 27.959 Unusable Fuel Supply … E-64 AC 27.961 Fuel System Hot Weather Operation … E-65 AC 27.961A Fuel System Hot Weather Operation … E-67 AC 27.963 Fuel Tanks: General … E-67 AC 27.963A Fuel Tanks: General … E-68 AC 27.963B Fuel Tanks: General … E-68 AC 27.965 Fuel Tank Tests … E-69 AC 27.967 Fuel Tank Installation … E-70 AC 27.969 Fuel Tank Expansion Space … E-72 AC 27.969A Fuel Tank Expansion Space … E-72 AC 27.971 Fuel Tank Sump … E-73 AC 27.971A Fuel Tank Sump … E-74 AC 27.973 Fuel Tank Filler Connection … E-74 AC 27.973A Fuel Tank Filler Connection … E-75 AC 27.975 Fuel Tank Vents … E-76 AC 27.975A Fuel Tank Vents … E-77 AC 27.975B Fuel Tank Vents … E-77 AC 27.977 Fuel Tank Outlet … E-78
FUEL SYSTEM COMPONENTS
AC 27.991 Fuel Pumps … E-80 AC 27.991A Fuel Pumps … E-81 AC 27.993 Fuel System Lines and Fittings … E-81 AC 27.995 Fuel Valves … E-82 AC 27.997 Fuel Strainer or Filter … E-82 AC 27.997A Fuel Strainer or Filter … E-83 AC 27.999 Fuel System Drains … E-84 AC 27.999A Fuel System Drains … E-85
Page x
Page No.
SUBPART E - POWERPLANT (continued)
OIL SYSTEM
AC 27.1011 Engines - General … E-86 AC 27.1013 Oil Tanks … E-86 AC 27.1015 Oil Tank Tests … E-87 AC 27.1017 Oil Lines and Fittings … E-88 AC 27.1019 Oil Strainer or Filter … E-88 AC 27.1019A Oil Strainer or Filter … E-89 AC 27.1021 Oil System Drains … E-90 AC 27.1027 Transmission and Gearboxes: General … E-90
COOLING
AC 27.1041 Cooling - General … E-92 AC 27.1041A General … E-94 AC 27.1043 Cooling Tests … E-94 AC 27.1045 Cooling Test Procedures … E-97 AC 27.1045A Cooling Test Procedures … E-98
INDUCTION SYSTEM
AC 27.1091 Air Induction … E-99 AC 27.1091A Air Induction … E-100 AC 27.1093 Induction System Icing Protection … E-101 AC 27.1093A Induction System Icing Protection … E-112.1
EXHAUST SYSTEM
AC 27.1121 General … E-113 AC 27.1123 Exhaust Piping … E-114
POWERPLANT CONTROLS AND ACCESSORIES
AC 27.1141 Powerplant Controls: General … E-117 AC 27.1141A Powerplant Controls: General … E-118 AC 27.1143 Engine Controls … E-118 AC 27.1143A Engine Controls … E-119 AC 27.1143B Engine Controls … E-119 AC 27.1145 Ignition Switches … E-120 AC 27.1147 Mixture Controls … E-120 AC 27.1151 Rotor Brake Controls … E-121 AC 27.1163 Powerplant Accessories … E-122
Page No.
Page xi
C 27-1B, Chg 9 A
6/23/23 AC 27-1B Chg 9 6/23/23
SUBPART E - POWERPLANT (continued)
POWERPLANT FIRE PROTECTION
Lines, Fittings, and Components AC 27.1183 AC 27.1185 AC 27.1187 AC 27.1189 AC 27.1191 AC 27.1193 AC 27.1193A AC 27.1194 AC 27.1195
AC 27.1301 AC 27.1303 AC 27.1305 AC 27.1305A AC 27.1305B AC 27.1305C
AC 27.1307 AC 27.1309 AC 27.1309A AC 27.1309B AC 27.1316 AC 27.1317
AC 27.1321 AC 27.1322 AC 27.1323 AC 27.1325 AC 27.1327 AC 27.1329 AC 27.1329A AC 27.1329B
AC 27.1335 AC 27.1335A AC 27.1337 AC 27.1337A
… E-124 Flammable Fluids … E-125 Ventilation and Drainage … E-126 Shutoff Means … E-127 Firewalls … E-128 Cowling and Engine Compartment Covering … E-132 Cowling and Engine Compartment Covering … E-133 Other Surfaces … E-134 Fire Detector Systems … E-135
SUBPART F - EQUIPMENT
GENERAL
Function and Installation … F-1 Flight and Navigation Instruments … F-1 Powerplant Instruments … F-7 Powerplant Instruments … F-8 Powerplant Instruments … F-9 Powerplant Instruments … F-11.1 Miscellaneous Equipment … F-12 Equipment, Systems, and Installations … F-13 Equipment, Systems, and Installations … F-30 Equipment, Systems, and Installations … F-30.1 Electrical and Electronic System Lightning Protection … F-31 High-Intensity Radiated Fields (HIRF) Protection … F-32
INSTRUMENTS: INSTALLATION
Arrangement and Visibility … F-34
Flight Director Systems … F-54.1 Powerplant Instruments … F-54.2 Powerplant Instruments … F-54.3
Warning, Caution, and Advisory Lights … F-34.2 Airspeed Indicating System … F-39 Static Pressure Systems … F-40 Magnetic Direction Indicator … F-41 Automatic Pilot System … F-41 Automatic Pilot System … F-51 Automatic Pilot System and Flight Guidance System … F-52.1
Flight Director Systems … F-53
Page xii
6/23/23 AC 27-1B Chg 9
Page No.
SUBPART F – EQUIPMENT (continued)
ELECTRICAL SYSTEMS AND EQUIPMENT
Electrical Systems and Equipment - General AC 27.1351 AC 27.1353 AC 27.1353A AC 27.1357 AC 27.1361 AC 27.1365 AC 27.1367
AC 27.1381 AC 27.1383 AC 27.1385 AC 27.1387 AC 27.1389 AC 27.1391
AC 27.1393
AC 27.1395
AC 27.1397 AC 27.1399 AC 27.1401
AC 27.1411 AC 27.1413 AC 27.1415 AC 27.1419 AC 27.1435 AC 27.1457 AC 27.1459 AC 27.1461
AC 27.1501
… F-55 Storage Battery Design and Installation … F-58
Energy Storage Systems … F-62.1 Circuit Protective Devices … F-62.13 Master Switch … F-64 Electric Cables … F-65 Switches … F-66
LIGHTS
Instrument Lights … F-67
Rear Position Lights
Rear Position Lights
Rear Position Lights
Landing Lights … F-67 Position Light System Installation … F-68 Position Light System Dihedral Angles … F-68 Position Light Distribution and Intensities … F-68 Minimum Intensities in the Horizontal Plane of Forward and … F-68
Minimum Intensities in Any Vertical Plane of Forward and … F-68
Maximum Intensities In Overlapping Beams of Forward and … F-68
Color Specifications … F-68 Riding Light … F-68 Anti-collision Light System … F-70
SAFETY EQUIPMENT
General … F-71 Safety Belts … F-73 Ditching Equipment … F-74 Ice Protection … F-75 Hydraulic Systems … F-97 Cockpit Voice Recorder … F-99 Flight Recorders … F-101 Equipment Containing High Energy Rotors … F-103
SUBPART G - OPERATING LIMITATIONS AND INFORMATION
General … G-1
Page xiii
AC 27.1B, Chg 9
AC 27.1503 AC 27.1505 AC 27.1509 AC 27.1519 AC 27.1521 AC 27.1521A AC 27.1521B AC 27.1523 AC 27.1525 AC 27.1527 AC 27.1529 AC 27.1529A
AC 27.1541 AC 27.1543 AC 27.1543A AC 27.1545 AC 27.1545A AC 27.1547 AC 27.1549 AC 27.1549A AC 27.1549B AC 27.1549C AC 27.1551 AC 27.1553 AC 27.1555 AC 27.1555A
AC 27.1557 AC 27.1559 AC 27.1561 AC 27.1565
Page No.
SUBPART G - OPERATING LIMITATIONS AND INFORMATION
(continued)
OPERATING LIMITATIONS
Airspeed Limitations: General … G-1 Never-Exceed Speed … G-4 Rotor Speed … G-6 Weight and Center of Gravity … G-8 Powerplant Limitations … G-9 Powerplant Limitations … G-10 Powerplant Limitations … G-10 Minimum Flightcrew … G-11 Kinds of Operations … G-15 Maximum Operating Altitude … G-16 Instructions for Continued Airworthiness (Maintenance Manual) … G-16 Instructions for Continued Airworthiness (Maintenance Manual) … G-20
MARKINGS AND PLACARDS
Marking and Placards - General … G-21 Instrument Markings: General … G-21 Instrument Markings: General … G-25.1 Airspeed Indicator … G-25.6 Airspeed Indicator … G-25.7 Magnetic Direction Indicator … G-25.9 Powerplant Markings … G-25.10 Powerplant Instruments … G-25.10 Powerplant Instruments … G-25.10
Powerplant Instruments … G-26 Oil Quantity Indicators … G-26.1 Fuel Quantity Indicator … G-26.2 Control Markings … G-27 Control Markings … G-28.1 Miscellaneous Markings and Placards … G-28.2 Limitations Placard … G-30 Safety Equipment … G-31 Tail Rotor … G-32
ROTORCRAFT FLIGHT MANUAL AND APPROVED MANUAL MATERIAL
AC 27.1581 AC 27.1583 AC 27.1585 AC 27.1585A
AC 27.1587 AC 27.1587A AC 27.1587B
AC 27.1589
Rotorcraft Flight Manual - General … G-33 Operating Limitations … G-40 Operating Procedures … G-42 Operating Procedures … G-45 Performance Information … G-45 Performance Information … G-47
Performance Information … G-48
Loading Information … G-48.1
Page xiv
6/23/23
Page No.
CHAPTER 3 - MISCELLANEOUS GUIDANCE (MG),
NORMAL CATEGORY ROTORCRAFT
AC 27 MG 1 Certification Procedure for Rotorcraft Avionics Equipment … MG 1-1
System Tests
§§ 27.79(b)(2), 27.141(b)(1), and 27.143(d)(1)
Including: Interior Arrangements, Equipment, Helicopter Terrain Awareness and Warning System (HTAWS), Radio Altimeter, and Flight Data Monitoring System.
System
Air Conditioning Systems
Systems (HUMS)
Systems (NVIS) Equipment
System
Installations
Assessment (FHA)
Installation in Part 27 Rotorcraft
AC 27 MG 2 Standardized Test Procedure for Rotorcraft DC Electrical … MG 2-1
AC 27 MG 3 Definition of Engine Isolation Features as Applied to … MG 3-1
AC 27 MG 4 Full Authority Digital Electronic Controls (FADEC) … MG 4-1 AC 27 MG 5 Agricultural Dispensing Equipment Installation … MG 5-1 AC 27 MG 6 Emergency Medical Service (EMS) Systems, Installations, … MG 6-1
AC 27 MG 7 Hour Meters or Time-in-Service Recording Devices in Rotorcraft .. MG 7-1 AC 27 MG 8 Substantiation of Composite Rotorcraft Structure … MG 8-1 AC 27 MG 9 Rotorcraft One-Engine-Inoperative (OEI) Power Assurance … MG 9-1 AC 27 MG 10 Advisory Material for Substantiation of Emergency Flotation … MG 10-1
AC 27 MG 11 Fatigue Evaluation of Rotorcraft Structure … MG 11-1 AC 27 MG 12 External Loads (see AC 27.865B) … MG 12-1 AC 27 MG 13 Systems Certification Considerations … MG 13-1 AC 27 MG 14 Certification Procedure for Installation of Vapor Cycle … MG 14-1
AC 27 MG 15 Airworthiness Approval of Rotorcraft Health Usage Monitoring … MG 15-1
AC 27 MG 16 Certification Procedure for Rotorcraft Night Vision Imaging … MG 16-1
AC 27 MG 17 Guidance on Analyzing an Advanced Flight Controls (AdFC) … MG 17-1
AC 27 MG 18 Helicopter Terrain Awareness and Warning System (HTAWS) … MG 18-1 AC 27 MG 19 Guidance on Electronic Display Systems (EDS) for Rotorcraft … MG 19-1
AC 27 MG 20 Human Factors (HF) … MG 20-1 AC 27 MG 21 Guidance on Creating a System Level Functional Hazard … MG 21-1
AC 27 MG 22 Rotorcraft One Engine Inoperative (OEI) Training Mode … MG 22-1 AC 27 MG 23 Automatic Flight Guidance and Control systems (AFGCS ) … MG 23-1
Page xv
APPENDICES
AC 27 Appendix A - Instructions for Continued Airworthiness … Apdx A-1 AC 27 Appendix B - Airworthiness Guidance for Rotorcraft Instrument Flight … Apdx B-1 AC 27 Appendix C - (reserved) (Criteria for Category A) … Apdx C-1
Page xvi
5/1/2014 AC 27.1B, Chg 4
FIGURES
The first digits in the figure number are the same as the related section number.
Figure No. Title Page
AC 27.45-1 H-V Requirements … B-20
Temperature - Sea Level Standard Day
400 RPM
Attached at Floor Level
Part 572B Anthropomorphic Dummy
Seat Bottom Cushion
AC 27.562-6 Post Test Condition
AC 27.45-2 IGE Controllability Requirements … B-21
AC 27.45-3 Shaft Horsepower vs. Turbine Outlet … B-22
AC 27.45-4 Uninstalled Takeoff Power Available … B-23
AC 27.45-5 Installed Takeoff Power Available, Anti-Ice Off, … B-24
AC 27.45-6 Power Assurance Check Chart … B-24.1
AC 27.71-1 Autorotational Characteristics - Typical … B-31
AC 27.79-1 Height-Velocity Diagram … B-43
AC 27.79-2 Altitude/Weight Accountability … B-44
AC 27.175-1 Static Longitudinal Stability … B-60.1
AC 27.175A-1 Static Longitudinal Stability … B-60.5
AC 27.251-1 Demonstration Points … B-70
AC 27.337-1 Load Factor Gross Weight Curve … C-7
AC 27.351-1 Sample Yaw/Forward Speed Diagram … C-12
AC 27.351-2 Safety Factors for Probability of Failure … C-13
AC 27.427-1 View Looking Forward … C-26
AC 27.427-2 View Looking Forward … C-27
AC 27.562-1 Seat Restraint System Dynamic Tests … C-47
AC 27.562-2 Schematic Floor Deformation Fixture; Seat Legs … C-54
AC 27.562-3 Schematic Test Fixture; Side Wall Mounted Seat … C-58
AC 27.562-4 Installation of Pelvic-Lumbar Spine Load Cell in … C-62
AC 27.562-5 Measurement to be Taken Over Full Width of … C-74
C-74
Page xvii
AC 27.1B, Chg 4 5/1/2014
FIGURES (continued)
Figure No. Title Page
AC 27.562-7 Impulse Shape … C-80
Size Relationships for Fail-Safe Substantiation … C113
Actuator Support-Landing Gear
Model XYZ
Organization …
Versus Applicable Cargo Type Data and Definition Summary
Hose-End Fitting Combinations
Calculations
Load Calculations, Frangible Bolts
Load Calculations, Frangible Baffle
AC 27.562-8 Change in Velocity … C-80
AC 27.571-1 Comparison Percent of Time in Level Flight … C-85
AC 27.573-1. Schematic diagram of building block tests … C102
AC 27.573-2. Characterization of Impact Damage … C-107
AC 27.573-3. Residual Strength vs. Time … C-112
AC 27.573-4. Illustration of Residual Strength and Damage
AC 27.621-1 Example of Casting Load Sheet Retract … D-24
AC 27.621-2 Example of Castings to be Static Tested for … D-26
AC 27.773-1 Cockpit Visibility … D-67
AC 27.801-1 Sea State Code - World Meteorological … D-90
AC 27.865B-1 U.S. Operational (Part 133) Rotorcraft-Load Combination … D-116
AC 27.931-1 Cantilevered Shaft, First Critical Speed … E-25
AC 27.931-2 Shaft Between Support Bearings, First Critical Speed … E-25
AC 27.952-1 Static Tension and Shear Loading Modes … E-50
AC 27.952-2 Hose Assembly Tests … E-51
AC 27.952-3 Minimum Average and Individual Loads for Hose and … E-52
AC 27.952-4 Typical Method of Breakaway Fuel Fitting Load … E-53
AC 27.952-5 Typical Methods of Frangible or Deformable Attachment … E-54
AC 27.952-6 Typical Methods of Frangible or Deformable Attachment … E-55
AC 27.955-1 Fuel Flow E-61 … E-61
Page xviii
5/1/2014 AC 27.1B, Chg 7
FIGURES (continued)
Figure No. Title Page
AC 27.1041-1 Additional Cooling Test Point … E-93
AC 27.1191-1 Table of Materials and Gauges Acceptable for … E-131
Fireproof Protective Devices with Flat Surface Geometries
Failure Condition Effects AC 27.1309-1 Relationship between Probability and Severity of … F-30.5
AC 27.1309-2 Failure Condition Categories and Probably Definitions … F-30.6
Diameter
Diameter
Dispensing Equipment Design
Valve
for Fail-Safe Substantiation
for Three Rotorcraft Types
AC 27.1309-4 Safety Assessment Process Overview … F-30.10 AC 27.1309-5 Depth of Analysis Flowchart … F-30.11 AC 27.1321-1 Primary Fields of View … F - 34
AC 27,1321-2 Secondary Fields of View … F – 34.1
AC 27.1329-1 Height Loss Method … F-45
AC 27.1329-2 Deviation Profile … F-49
AC 27.1329-3 Deviation Profile … F-50
AC 27.1419-1 Continuous Icing-Temperature vs. Altitude Limits … F-93
AC 27.1419-2 Intermittent Icing-Temperature vs. Altitude Limits … F-94
AC 27.1419-3 Continuous Icing-Liquid Water Content vs Drop … F-95
AC 27.1419-4 Intermittent Icing-Liquid Water Content vs. Drop … F-96
AC 27 MG 3-1 Part 29 Engine Isolation Rules … MG 3-5
AC 27 MG 5-1 Acceptable Ultimate Load Factor for Agricultural … MG 5-3
AC 27 MG 5-2 Sketch of Tank Pressure Test … MG 5-7
AC 27 MG 6-1 Typical Liquid Oxygen System … MG 6-21
AC 27 MG 6-2 Typical Liquid Oxygen System - Using Combination … MG 6-22
AC 27 MG 8-1 Schematic Diagram of Building Block Tests … MG 8-16
AC 27 MG 8-2 Characterization of Impact Damage … MG 8-20
AC 27 MG 8-3 Residual Strength vs. Time … MG 8-23
AC 27- MG 8-4 Residual Strength and Damage Size Relationships … MG 8-24
AC 27 MG 9-1 Installed Engine Fuel Flow Capacity Check … MG 9-8
AC 27 MG 11-1 Example of Variation in Time Spent in Level Flight … MG 11-7
AC 27 MG 11-2 Flight Regime to be Investigated Power-On Operation … MG 11-17
Page xix
AC 27.1B, Chg 7 xx/xx/2014
FIGURES (continued)
Figure No. Title Page
AC 27 MG 11-3 Flight Regime to be Investigated for Power-Off … MG 11-17
Operation
Investigated
Reduction of Software Level
Software with a Ground Base that uses COTS Software for Operational Software
AC 27 MG 11-4 Simplified Analytical Method for Safe Life Evaluation … MG 11-18
AC 27 MG 11-5 Typical S/N Curve for Safe Life Evaluation … MG 11-18
AC 27 MG 11-6 Elements of Safe Life Determination … MG 11-19
AC 27 MG 11-7 Flight Load Measurement Program Conditions to be … MG 11-20
AC 27 MG 11-8 Lifting Helicopter Load Measurement … MG 11-23
AC 27 MG 11-9 Example of Twin Turbine Usage Spectrum … MG 11-24
AC 27 MG 14-1 Refrigeration Cycle … MG 14-7
AC 27 MG 15-1 Flow Chart for Use of Mitigating Actions Applied for … MG 15-8
AC 27 MG 15-2 Flow Chart for Application of HUMS Specific … MG 15-11
AC 27 MG 17-1 Verification Methodology … MG 17-4
AC 27 MG 19-1 Primary Field of View … MG 19-15
AC 27 MG 19-2 Secondary Field of View … MG 19-16
AC 27 MG 20-1 Primary and Secondary Horizontal Fields of View … MG 20-18
AC 27 MG 20-2 Primary and Secondary Vertical Fields of View … MG 20-19
AC 27 MG 20-3 Sample HF Compliance Matrix … MG 20-27
AC 27 MG 21-1 Generic Examples by ATA … MG 21-5
AC 27 APX B-1 Rotorcraft Dynamic Stability Requirements for IFR … Apdx B-27
Page xx
5/1/2014 AC 27.1B, Chg 4
Acronyms
AC ACO ADF ADI AEH AEO AdFC AFCS
AFGCS
AGL AHRS
Amdt. APU ATC BIM CAM CAR CAS CBIM
CDP CFR CG COTS CPS CRFS CRI CRT CVR DER
DME
EASA
ECAS
ECU EDS
advisory circular aircraft certification office automatic direction finding attitude direction indicator airborne electronic hardware all engines operating advanced flight control automatic flight control systems automatic flight guidance and control systems above ground level attitude heading reference system Amendment auxiliary power unit air traffic control blade inspection method cockpit area microphone Civil Air Regulations calibrated air speed cockpit blade inspection method critical decision point Code of Federal Regulations center of gravity commercial off-the-shelf cycles per second crash resistant fuel system certification review item cathode ray tube cockpit voice recorder designated engineering representative distance measuring equipment European Aviation Safety Agency engine caution advisory systems environmental control unit electronic data system
EFIS electronic flight instrument System[Replaced by EDS.] EFP engine failure point EHE exhaust heat exchanger ELOS equivalent level of safety ELT emergency locator transmitter EMC electromagnetic compatibility EMI electromagnetic interference EMS emergency medical service EOL end of life EUROCAE European Organization for
Civil Aviation Equipment EVS enhanced vision system FAA Federal Aviation Administration FADEC full authority digital engine control FAR Federal Aviation Regulations [OBSOLETE term.] FEM finite element modeling FHA functional hazard assessment FMEA failure mode and effects analysis FPM feet per minute FPS feet per second FTA fault tree analysis GPS global positioning system GW gross weight HEC human external cargo HF high frequency HIRF high intensity radiated fields HRD high rate of discharge HUMS health and usage monitoring systems HV height-velocity IAS indicated airspeed ICA instructions for continued airworthiness ICAO International Civil Aviation Organization ICS inter-communication system IFR instrument flight rules
Page xxi
AC 27.1B, Chg 4 5/1/2014
PCDS personnel carrying device IGE in ground effect Systems IIDS integrated instrument display system ILS instrument landing system IMC instrument meteorological conditions INS inertial navigation system ISA international standard atmosphere ISIS integral spar inspection system ITT inter-turbine temperature KCAS knots calibrated airspeed KIAS knots indicated air speed KTAS knots true airspeed LDP landing decision point LPV localizer performance with vertical guidance LRU line replaceable unit LWC liquid water content MC maximum continuous MCP maximum continuous power MEL minimum equipment list MG miscellaneous guidance MGB main gearbox MGT measured gas temperature MGW maximum gross weight MMEL master minimum equipment list MSL mean sea level MVD median volume diameter NASA National Aeronautics and Space Administration NDI non-destructive inspection NM nautical mile NPRM notice of proposed rulemaking NTSB National Transportation Safety Board NVG night vision goggles NVIS night vision imaging systems OAT outside air temperature OEI one engine inoperative OGE out of ground effect PBA pitch bias actuator
Page xxii
PCF PIO PSA PSIG
QPL RFM RFMS
RGL
RPM RTCA
RVR SAE
SAR SAS SCAS
SHP S/N SRM SSA STC STOL TBO TC TCDS TDP TIA TIR TOP TOT TSO TVP VBIM VFR VMC
post crash fire pilot induced oscillation preliminary safety assessment pounds per square inch gauge qualified parts list rotorcraft flight manual rotorcraft flight manual supplement Regulatory and Guidance Library revolutions per minute Radio Technical Commission Of Aeronautics runway visual range Society of Automotive Engineers search and rescue stability augmentation system stability and control augmentation systems shaft horsepower stress vs. number of cycles structural repair manual system safety assessment supplemental type certificate short takeoff and landing time between overhaul type certificate type certificate data sheet takeoff decision point type inspection authorization type inspection report takeoff power turbine outlet temperature technical standard order true vapor pressure visual blade inspection method visual flight rules visual meteorological conditions
2/4/2016
VOR very high frequency omnidirectional range radio
VSI vertical speed indicator V/STOL vertical/short takeoff and
landing VTOL vertical takeoff and landing WAT weight, altitude, temperature
HD HP
VD VH
VMO
VNE VTOSS
VX VY MMO
NF NG NP NR
CD CL CP CT
AC 27-1B, Chg 7
Altitudes
density altitude pressure altitude
V speeds
diving speed speed in level flight with maximum continuous power maximum operating limit speed never-exceed speed takeoff safety speed for Category A rotorcraft speed for best angle of climb speed for best rate of climb maximum operating mach number
N speeds
free turbine speed gas generator speed power turbine speed rotor speed
Coefficients
coefficient of drag coefficient of lift coefficient of power coefficient of thrust
Page xxiii
CHAPTER 1 PART 21 FAR 21 - GENERAL › AC 21.16 SPECIAL CONDITIONS
9/30/99 AC 27-1B
CHAPTER 1. PART 21
FAR 21 - GENERAL
CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS
(Amendment 21-50)
AC 21.16. § 21.16 SPECIAL CONDITIONS.
a. The Process. Chapter 2, Section 1, Paragraph 8 of the Type Certificate Handbook, Order 8110.4A, provides detailed guidance on the special conditions process. However, much of that material has been outdated with the implementation of the Aircraft Certification Directorate Program. Rotorcraft special conditions are processed through the Rotorcraft Standards Staff, ASW-110. That office will ensure coordination with the affected agency and industry elements including the Assistant Chief Counsel. All comments will be considered and the disposition documented by the Rotorcraft Directorate. ASW-100 will issue the special conditions.
b. Basis for Development.
(1) Special conditions are justified on the basis of the existing Part 27 being inadequate or inappropriate due to novel or unusual design features of the rotorcraft to be certificated.
(2) The phrase “novel or unusual” as used in § 21.16 is a very relative term. As used hereafter in applying § 21.16 to justify the issuance of special conditions, “novel or unusual” will be taken with respect to the state of technology envisaged by the applicable airworthiness standards of this subchapter. It must be recognized that in some areas which will vary from time to time, the state of the regulations may somewhat lag the state of the art in new design because of the rapidity in which the state of the art is advancing in civil aeronautical design and because of the time required to develop the experience base needed by the FAA/AUTHORITY to proceed with general rulemaking. Applicants for type certification of a new design have the opportunity to mitigate the impact of not knowing the precise airworthiness standards to be applied for “novel or unusual design features” by consulting with the FAA/AUTHORITY early in their certification planning when such features are suspected or known by the applicant to exist. It should also be recognized that, because of the intentional objective nature of the airworthiness standards of this subchapter, many new design features which might be thought of as “novel or unusual” may already be adequately covered by existing regulations, thus obviating the need to issue special conditions.
(3) Before proposing special conditions, the certification staff should very thoroughly analyze the existing regulations and ensure they are inadequate or inappropriate in light of a new and novel design feature.
Page FAR 21 - 1
AC 27-1B 9/30/99
AC 21.31. § 21.31 TYPE DESIGN.
The regulatory basis for requiring data to define the design is contained in § 21.31. This section is self-explanatory and broad enough in scope to give the certification staff access to sufficient data to determine compliance with Part 27.
CHAPTER 1 PART 21 FAR 21 - GENERAL › AC 21.35 FLIGHT TESTS
AC 21.33. § 21.33 INSPECTION AND TESTS.
a. Applicant Responsibility. Section 21.33 requires the applicant to:
(1) Ensure the test rotorcraft conforms to the type design. This must be accomplished prior to presentation to the FAA/AUTHORITY for testing.
(2) Conduct all inspections and tests necessary to determine compliance with the airworthiness and noise requirements.
b. FAA/AUTHORITY Responsibility.
(1) The design evaluation engineers should ensure that the type design is adequate in their technical area and that the inspections and tests to be conducted are appropriate and sufficient to show compliance with Part 27.
(2) As changes to the rotorcraft are made during the test program, the flight test crew should ensure that the appropriate design evaluation engineer concurs with the change and the conformity inspection of the change has been conducted.
AC 21.35 § 21.35 (Amendment 21-59) FLIGHT TESTS.
a. Explanation.
(1) This section outlines the requirements of the applicant for aircraft type certification and should be used in conjunction with FAA Order 8110.4A, Section 5. Section 21.35 requires, in part, that the applicant conduct sufficient flight tests to show compliance with the flight requirements throughout the proposed flight envelope. The results of the applicant’s flight test should be submitted to the FAA/AUTHORITY in report form for evaluation to determine what verification flight tests the FAA/AUTHORITY may elect to conduct. The report should conclude that in the applicant’s opinion the test aircraft complies with the applicable certification requirements. The FAA/AUTHORITY verification flight test should include, but not be limited to, the critical or marginal results contained in the applicant’s flight test report. The FAA/AUTHORITY’s role in the certification effort is not envisioned to be one of conducting day-to-day routine flight tests with the applicant, but only to verify his results through limited sampling. In certain tests, such as high altitude testing at a remote mountain site, there is an advantage in conducting flight tests concurrently with the applicant. Additionally, the FAA/AUTHORITY can provide technical flight test
Page FAR 21 - 2
9/30/99 AC 27-1B
assistance to the applicant in certain cases. This can be done after a cursory review and a letter of authorization is issued to the flight test crew.
(2) Preflight Test Planning. After the applicant’s flight test report is reviewed, it should be determined what FAA/AUTHORITY engineering flight tests are necessary. These tests are normally specified in the Type Inspection Authorization (TIA). At the same time the FAA/AUTHORITY must know and agree to the applicant’s proposed means of data acquisition, reduction, and expansion of the flight test data. The adequacy of the test instrumentation should be evaluated prior to official type certification tests (reference paragraph AC 21.39).
(3) Order of Testing. The Federal Aviation Regulations are so worded that the results of some flight tests have a definite bearing on the conduct of other tests. For this reason, and to minimize retesting, careful attention should be given to the order of testing. The exact order of testing will be determined only by considering the particular rotorcraft and test program involved. Tests which are particularly important in the early stages of the program are:
(i) Airspeed calibration: All tests involving airspeed depend upon the calibration.
(ii) Engine power available determination.
(iii) Engine cooling.
(4) Test Groupings.
(i) Weight and c.g.: In addition to the regulatory relationship of one test to another, efficient testing requires that consideration be given to the accomplishment of as many tests on a single flight as can be accommodated successfully.
(ii) Special Instrumentation. Similarly, consideration should be given to grouping of tests that involve special instrumentation. Examples of these are takeoff and landing tests which usually require group equipment to record horizontal distance, height, and time. Ground calibration of the airspeed indicating system can be accomplished at the same time. It is the applicant’s responsibility to provide the necessary instrumentation.
(5) Functional and Reliability Testing
(i) Section 21.35(b)(2) requires that the applicant determine that “there is reasonable assurance that the aircraft, its components, and its equipment are reliable and function properly.” Section 21.35(f)(1) requires a Function and Reliability (F&R) program of 300 hours for turbine engine powered aircraft incorporating engines of a type not previously used in a type certificated aircraft. Section 21.35(f)(2) requires a 150-hour F&R program for all other aircraft. The following reflects general practices that
Page FAR 21 - 3
AC 27-1B 9/30/99
have been used during rotorcraft certification programs. FAA/AUTHORITY have supported proposals which gave F&R test time credit for certification testing in lieu of dedicated F&R testing. In establishing such credit, the following should be considered:
(A) The point in time in which the rotorcraft reaches substantial conformity with the approved type design.
(B) The extent and complexity of the new design.
(C) For a previously certified rotorcraft, the F&R program requirement should be commensurate with the modification or change in type design and may be zero.
(ii) Historically, for major rotorcraft type certification programs, flight time credit has been limited so as to require an irreducible minimum of 50 hours of dedicated F&R flight time. For rotorcraft programs that involved new engine installations (mature engine design) or drive train/rotor system changes on previously certified aircraft (TC amendments or STC’s), flight time credit has been liberal and often resulted in very little or no dedicated F&R testing.
b. Procedures.
(1) Type Certification Flight Tests.
(i) Prior to initiating official FAA/AUTHORITY flight tests, a conformity inspection of the test aircraft must be accomplished. This is needed to assure that the test aircraft is in the proper configuration or “conforms” to the engineering drawings and documents that have been submitted to FAA/AUTHORITY, evaluated, and approved. It is absolutely essential to know the configuration being tested in any engineering flight evaluation. Conformity inspection prior to TIA flight tests assures that testing will not be wasted because of configuration uncertainties.
(ii) FAA Order 8110.4A, paragraph 67, contains a requirement that the applicant must keep the FAA/AUTHORITY advised of any configuration changes to the aircraft. The manufacturing inspector should keep the FAA/AUTHORITY flight test pilot apprised of any change which may affect safety of the test aircraft or may influence test results.
(iii) Results of the conformity inspection and the engineering flight test program must be documented. This is normally done in the Type Inspection Report (TIR). Results may be documented in any acceptable engineering format. The report should be in sufficient detail to clearly show how compliance with each appropriate section of the rules was determined.
(iv) The flight test pilot must assure that the FAA/AUTHORITY manufacturing inspector and certification engineer are aware of all configuration
Page FAR 21 - 4
9/30/99 AC 27-1B
changes found necessary as a result of FAA/AUTHORITY tests. The manufacturing inspector is responsible for assuring that all changes are incorporated into production drawings after the design data reflecting the change have been approved by the certification engineer.
(v) Additional flight test responsibilities, procedures, and requirements during the certification flight test process are contained in FAA Order 8110.4A, Section 5, Flight.
(2) Function and Reliability Tests.
(i) A comprehensive and systematic check of all aircraft components must be made to assure that they perform their intended function and are reliable.
(ii) F&R testing should be accomplished on an aircraft which conforms to the type design. Non-conformities must be documented and accepted. F&R testing should follow the type certification testing described in paragraph AC 21.35b(1) above to assure that significant changes resulting from type certification tests are incorporated on the aircraft prior to F&R tests.
(iii) All components of the rotorcraft should be periodically operated in sequences and combinations likely to occur in service. Ground inspections should be made at appropriate intervals to identify potential failure conditions; however, no special maintenance beyond that described in the aircraft maintenance manual should be allowed.
(iv) A complete record of defects and failures should be maintained along with required servicing of aircraft fluid levels. Results of this record should be consistent with inspection and servicing information provided in the aircraft maintenance manual.
(v) A certain portion of the F&R test program may focus on systems, operating conditions, or environments found particularly marginal during type certification tests.
(vi) A substantial portion of the flying should be on a single aircraft. The flying should be carried out to an intensive schedule on an aircraft that is very close to the final certification standard, operated and maintained as though it were in service. A range of representative ambient operating conditions and sites should be considered. It is acceptable for non-F&R flight testing conducted at various sites and in varying ambient conditions to be used to satisfy the F&R requirements for those conditions.
Page FAR 21 - 5
CHAPTER 1 PART 21 FAR 21 - GENERAL › AC 21.39 FLIGHT TEST INSTRUMENTATION CALIBRATION AND CORRECTION REPORT
AC 27-1B 9/30/99
AC 21.39. § 21.39 (Amendment 21-59) FLIGHT TEST INSTRUMENT CALIBRATION
AND CORRECTION REPORT.
a. Explanation. It is the applicant’s responsibility to provide instrumentation for all parameters needed to show compliance with the airworthiness regulations.
(1) For those data which are necessary to show compliance with the regulations, a permanent record should be established. A permanent record is acceptable in either graphical or photographic form, and in some instances a manual recording may be satisfactory.
(2) Regardless of the record form, the accuracy of the record must be established by reference to a laboratory standard traceable to the National Bureau of Standards.
(3) If multiplexing is used, the time base must be synchronized to a reference point from which the magnitude of each parameter can unquestionably be determined. Also, the sampling rate should be sufficiently frequent to ensure that the maximums, minimums, and trends of magnitude of the parameter are recorded with respect to time.
b. Procedures. Prior to conducting flight tests, the FAA/AUTHORITY flight test team should review the applicant’s flight test instrumentation, calibration, and correction report.
(1) The frequency of recalibration varies with the consistency of the instrumentation under consideration. For example, cyclic and collective position is sometimes calibrated immediately before and after a flight where these parameters are used to provide critical flight data. Six months is a typical interval for recording/signal conditioning and nonstrain gage sensors, while 1 year is typical for strain gaged components. Also, environmental effects such as vibration, humidity, temperature, etc., should be considered when determining whether recalibration is necessary.
(2) The highest and lowest magnitude of the parameter being recorded should be considered when establishing the scale for instrumentation. Ideally, the highest magnitude throughout the flight would fall on the maximum indicating point of the recording.
Page FAR 21 - 6
SUBPART A - GENERAL › AC 27.1A (AMENDMENT 27-33) APPLICABILITY
9/30/99 AC 27-1B
CHAPTER 2. PART 27 AIRWORTHINESS STANDARDS NORMAL CATEGORY ROTORCRAFT
SUBPART A - GENERAL
AC 27.1. § 27.1 APPLICABILITY.
a. Explanation. This section prescribes the rotorcraft categories eligible for certification under this Part. There is no minimum weight limit for certification under Part 29; however, Part 27 is applicable to rotorcraft with maximum weights of 6,000 pounds or less.
(1) Without Engine Isolation. For single-engine rotorcraft and multiengine rotorcraft without engine isolation, the height-velocity (HV) diagram is conducted with sudden failure of all engines, and the takeoff maneuver must pass through the clear area of the diagram to the 50-foot point with all engines operating.
(2) With Engine Isolation. Part 27 multiengine rotorcraft may be certificated with engine isolation features (reference paragraph AC 27 MG 3). These rotorcraft are not required to meet the Part 29, Category A, performance requirements, and continued flight after an engine failure is not assured since under some conditions failure of the remaining engine may occur after a limited time. The takeoff is conducted with all engines operating, while the height-velocity diagram is determined with the most critical engine inoperative. If complete Part 29, Category A, design features and performance are achieved, the Category A performance may be included in the FAA/AUTHORITY-approved portion of the Rotorcraft Flight Manual although this performance is not required by the regulations.
b. Procedures. None.
AC 27.1A. § 27.1 (Amendment 27-33) APPLICABILITY.
a. Explanation. Amendment 33 formally introduced the requirements for certification of a Part 27 rotorcraft to Category A design and performance standards. These standards are found in Appendix C of Part 27. The establishment of Category A design and performance for multiengine Part 27 rotorcraft is still voluntary. If so requested, the corresponding AC 29-2C material applies.
b. Procedures. None
Page A - 1
SUBPART A - GENERAL › 27.2 (Amendment 27-28) SPECIAL RETROACTIVE REQUIREMENTS
AC 27-1B 9/30/99
AC 27.1B § 27.1 (Amendment 27-37) APPLICABILITY.
a. Explanation. Amendment 27-37 increases the normal category rotorcraft maximum gross weight limit from 6,000 to 7,000 pounds and introduces new airworthiness requirements. The gross weight increase was intended to compensate for past regulatory actions that, in effect, cumulatively increased the gross weight of normal category rotorcraft. The amendment also adds an explicit nine-passenger seat limitation. The new airworthiness requirements were intended to increase the level of safety to support a potential increase in the number of passenger seats associated with the increase in maximum gross weight limit.
b. Procedures. None
AC 27.2 § 27.2 (Amendment 27-28) SPECIAL RETROACTIVE REQUIREMENTS.
a. Explanation.
(1) Amendment 27-28 requires a combined shoulder harness and safety belt (also called a torso restraint system) at each occupant’s seat for all rotorcraft manufactured after September 16, 1992.
(2) The design features of the restraint system are mainly contained in this section rather than having to refer to other sections within Part 27 except for a general reference to the differing strength standards between earlier static strength only standards and the static and dynamic strength standards of Amendment 27-25.
(3) Combined safety belt and harness strength standards system follows:
(i) Those rotorcraft type designs certificated to static strength standards alone prior to Amendment 27-25, such as 4 g’s forward may use belt and harness systems, characterized as 1,500 pounds strength systems, provided they comply with those standards. TSO C22f and earlier restraint systems have such ratings. A combined belt and harness with a 1,500 pounds rating, which comply with the Part 27 standards for the rotorcraft type design, but are not necessarily TSO approved, may be approved as a part of the type design. Such design information for a non-TSO’d item would be included in a note on the aircraft type certificate data sheet (TCDS) or specification sheet by part number as “required equipment.” TSO C114-approved torso restraint systems, characterized as 3,000 pounds strength system, may be used provided the design features comply with this section, but no special information on the TCDS is necessary.
(ii) Those rotorcraft type designs certified to dynamic test requirements of Amendment 27-25 should use torso restraint systems approved under TSO C114 or approved under equivalent standards such as those contained in Part 27.
(4) Load Distribution and Design Requirements. Although not stated in § 27.2, a 60 percent and 40 percent load distribution between the safety belt and harness,
Page A - 2
9/30/99 AC 27-1B
respectively, is required in § 27.785(g). The safety belt should withstand 100 percent if the safety belt is capable of being used alone. Also, the safety belt or harness attachments to the seat or structure should include the 1.33 factor described in § 27.785(f)(2) of Amendment 27-21 for those rotorcraft with that certification criteria or should include the 1.15 factor as described in § 27.625 (and predecessor Part 6) standards for those rotorcraft with the earlier certification criteria. A factor is used whether test or analysis methods are used for static substantiation of the seating systems. Refer to paragraph AC 27.785c(i) (§ 27.785).
(5) The companion operating rule change of Amendment 91-220, amended § 91.205 (Amendment 91-223), affecting the aircraft equipment requirements. Operating rule § 91.107(a) already requires use of the harness whenever the aircraft seat is so equipped.
b. Procedures.
(1) A TSO-approved combined safety belt and harness or torso restraint system may be used provided the installation requirements in § 27.2 are satisfied. A combined belt and harness (not necessarily TSO approved) may be approved as a part of the rotorcraft type design and so noted on the aircraft specification or TCDS.
(2) Structural analysis or static test may be used. For those rotorcraft designs that are subject to the dynamic test standards of § 27.562, the torso restraint system is required to be qualified for the particular use or installation in each rotorcraft type design. A dynamic test may be required for alternate restraint systems as well as the originally approved system. TSO C114 approval does not constitute approval for installation of a restraint system in a rotorcraft design subject to dynamic test.
(i) Paragraph 27.562 of this AC concerns in part the dynamic test standards of Amendment 27-25.
(ii) AC 23-4 dated June 20, 1986, concerns static test procedures for small airplane seats and restraint systems. (Certain small airplanes manufactured after December 12, 1986, should have harnesses for each seat also.) A test proposal for rotorcraft installations may adopt procedures appropriate to the particular installation. The 60/40 percent distribution is sufficiently achieved when the blocks in Figure 4 of AC 23-4 are used.
(iii) The static design side load for the harness installation may be proven by test or analysis using the load distribution previously noted. For “older” designs, the side load of § 27.561(b)(3)(iii) is 2.0g, and for later designs (Amendment 27-25 and later), it is 8.0g.
Page A - 3
SUBPART A - GENERAL › 27.2 (Amendment 27-37) SPECIAL RETROACTIVE REQUIREMENTS
AC 27-1B 9/30/99
AC 27.2A § 27.2 (Amendment 27-37) SPECIAL RETROACTIVE REQUIREMENTS.
a. Explanation. Amendment 27-37 specifies that for any change in type design to a rotorcraft that increases the passenger-seat capacity to a number greater than seven (and limited to a maximum of nine) the rotorcraft must meet all the applicable paragraphs of this Part in effect on October 18, 1999, regardless of the original certification basis. Additionally, the amendment allows for an increase in maximum gross weight from 6,000 pounds up to 7,000 pounds for previously certified rotorcraft provided there is no increase in the maximum passenger-seat capacity beyond that for which the rotorcraft was certificated on October 18, 1999. If a passenger-seat capacity increase is requested in addition to an increase in gross weight above 6,000 pounds, then, once again, all applicable paragraphs of this Part in effect on October 18, 1999, must be met.
b. Procedures. None.
Page A - 4
SUBPART B - FLIGHT › 27.21 (Amendment 27-21) PROOF OF COMPLIANCE
9/30/99 AC 27-1B
CHAPTER 2. PART 27 AIRWORTHINESS STANDARDS NORMAL CATEGORY ROTORCRAFT
SUBPART B - FLIGHT
GENERAL
AC 27.21. § 27.21 (Amendment 27-21) PROOF OF COMPLIANCE.
a. Explanation.
(1) This section provides a degree of latitude for the FAA/AUTHORITY test team in selecting the combination of tests or inspections required to demonstrate compliance with the regulations. Compliance should be shown for applicable combinations of gross weight, center of gravity, altitude, temperature, airspeed, rotor RPM, etc. Engineering tests are designed to investigate the overall capabilities and characteristics of the rotorcraft throughout its operational envelope. Testing will identify operating limitations, normal and emergency procedures, and performance information to be included in the FAA/AUTHORITY-approved portion of the flight manual. The testing must also provide a means of verifying that the rotorcraft’s actual performance, structural design parameters, propulsion components, and systems operations are consistent with all certification requirements.
(2) Section 21.35 requires, in part, that the applicant show compliance with the applicable certification requirements, including flight test, prior to official FAA Type Inspection Authorization (TIA) testing. Compliance in most cases requires systematic flight testing by the applicant. After the applicant has submitted sufficient data to the FAA/AUTHORITY showing that compliance has been met, the FAA/AUTHORITY will conduct any inspections, flight, or ground tests required to verify the applicant’s test results. FAA/AUTHORITY compliance may be partially determined from tests conducted by the applicant if the configuration (conformity) of the rotorcraft can be verified. Compliance may be based on the applicant’s engineering data and a spot check or validation through FAA/AUTHORITY flight tests. The FAA/AUTHORITY testing should obtain validation at critical combinations of proposed flight variables if compliance cannot be inferred using engineering judgment from the combinations investigated.
(3) Performance tests include minimum operating speed (hover), takeoff and landing, climb, glide, height-velocity, and power available. Certain other performance tests, such as critical engine survey for multiengine installations, may be conducted to meet specific requirements. Detailed performance test procedures and allowable extrapolation or simulation limits are contained in the respective paragraphs in this AC.
(i) Hover tests are conducted to determine various combinations of altitude, temperature, and gross weight for both in-ground-effect (IGE) and, if required
Page B - 1
AC 27-1B 9/30/99
by the applicant, out-of-ground effect (OGE) conditions. From these data, the hover ceiling may be calculated.
(ii) Takeoff and landing tests are conducted to determine that a takeoff or landing can be safely executed without requiring exceptional piloting skill or favorable conditions at any approved combination of altitude, temperature, and gross weight.
(iii) For rotorcraft other than helicopters, climb tests establish the variations of rate-of-climb at the best rate-of-climb or published climb airspeed(s) at various combinations of altitude, temperature, and gross weight. For helicopter, climb tests are conducted as required to determine the best rate-of-climb speed, Vy.
(iv) Height-velocity tests are conducted to determine the boundaries of the height versus airspeed envelope from which a safe landing can be accomplished following an engine failure.
(v) Power available tests are conducted to verify the calculated installed specification engine performance model on which published performance is based.
(4) The purpose of rotorcraft stability and control tests is to verify that the rotorcraft possesses the minimum qualitative and quantitative flying qualities and handling characteristics required by the applicable regulations. In order to assess the handling qualities, standardized test procedures must be utilized and the results analyzed by accepted methods. Section 27.21(a) allows calculation and inference which includes extrapolation and simulation, whereas § 27.21(b) requires demonstration of controllability, stability, and trim. Combinations of § 27.21(a) and (b) may be used to show compliance with the operating envelope limits. Test methods and equipment are described in individual paragraphs of this advisory circular.
b. Procedures.
(1) Efforts should begin early in the certification program to provide advice and assistance to the applicant to ensure coverage of all certification requirements. The applicant should develop a comprehensive test plan which includes the required instrumentation.
(2) The tests and findings specified in paragraph AC 27.21a(3) are required of the applicant to show basic airworthiness and probable compliance with the minimum requirements specified in the applicable regulations. After these basic findings have been submitted and reviewed, a Type Inspection Authorization, or equivalent, can be issued. The FAA/AUTHORITY will develop a systematic plan to spotcheck and confirm that compliance with the regulations has been shown. The test plan will consider combinations of weight, center of gravity, and RPM and cover the range of altitude and temperature for which certification is requested.
Page B - 2
SUBPART B - FLIGHT › 27.25 (Amendment 27-14) WEIGHT LIMITS
9/30/99 AC 27-1B
AC 27.25. § 27.25 (Amendment 27-14) WEIGHT LIMITS.
a. Explanation.
(1) This section is definitive and specifies criteria for establishing maximum and minimum certificating weights. These weights may be based on those selected by the applicant, design requirements, or the limits for which compliance with all applicable flight requirements has been shown.
(2) Typical requirements that may establish the maximum and minimum weight limits include:
(i) Maximum: Structural limits, performance requirements, stability, and controllability requirements.
(ii) Minimum: Autorotative rotor RPM, stability, and controllability requirements.
(3) Jettisonable External Cargo.
(i) Section 27.25(c) was added by Amendment 27-11 to provide a basis for approving an increased gross weight that would be an external jettisonable load. Section 27.865, “External load attaching means, “ includes hoist and hook design features for the load attaching devices that were added to Part 27 but removed from § 133.43. Part 133, “Rotorcraft External-Load Operations,” was also amended (Amendment 133-5) concurrently to complement the changes to Parts 27 and 29.
(ii) Approvals under the policy in Review Cases Nos. 37 and 55 of FAA Order 8110.6 were no longer necessary. These review cases concerned the policy/standards for external cargo configurations using a cargo hook whenever the standard limitations were exceeded. If the standard limitations were not exceeded, external cargo hooks and hoists and external cargo configuration approvals could be made under Part 133, Subpart D, prior to Amendment 133-5.
(iii) In the preamble of Amendment 27-11 (Proposal 2-99, 41 FR 55454; December 20, 1976) the agency stated that “...§ 27.25(c) and § 29.25(c) are intended to provide only a total weight standard for approving the rotorcraft structure for operation under Part 133.” The policy in Review Case No. 55 also indicates the powerplant or propulsion system is also subject to evaluation for the increased weight. As indicated in § 27.865, fatigue substantiation of the external cargo attaching means is not required. The rotorcraft structure, rotors, etc., are only subject to fatigue evaluation under § 27.571 whenever the standard structural limitations are exceeded (Review Case No. 55).
(iv) Whether or not the standard limitations are exceeded, the flight characteristics evaluations/standards of § 133.41 are appropriate even for engineering
Page B - 3
SUBPART B - FLIGHT › 27.25 (Amendment 27-44) WEIGHT LIMITS
approval. Section 133.41 is also appropriate for the individual operator to obtain his operating certificate. The operator may use an FAA/AUTHORITY approved RFM supplement to prepare his own rotorcraft load combination flight manual required by § 133.47.
b. Procedures.
(1) It may not be possible to demonstrate quantitatively all the flight requirements at the minimum weight because of test instrumentation requirements. The test team must ensure that the rotorcraft complies with the applicable requirements at the lowest permissible flying weight. This evaluation may be done qualitatively with the test instrumentation removed and with minimum crewmembers if no critical areas exist or are anticipated. Additionally, reasonable extrapolation is permitted. However, if critical areas at minimum flying weights are apparent, extrapolation should not be permitted.
(2) Whenever a gross weight increase under § 27.25(c) is requested, a TIA evaluation is necessary to evaluate the new limitations and ensure that § 133.41 for typical or representative cargo weights and/or shapes (or density) is satisfactory. All possible combinations of weights and shapes are not evaluated. The representative configurations may be noted in the RFM or RFM Supplement for the operator’s information. Sections 133.41 and 133.47 must be satisfied by the individual operator for the particular case at hand. The approved RFM or RFM Supplement should provide the necessary limitations and any other information about the representative cargo configurations evaluated. Section 133.41 also permits the operator to obtain approval of additional and unique cargo configurations provided approved limitations are observed. Paragraph AC 27.1581 concerns the RFM and its contents.
(3) See AC 29-2C, Certification of Transport Category Rotorcraft, paragraph AC 29.571, concerning § 29.571, for fatigue substantiation and external cargo considerations that apply to § 27.571 as well.
(4) Refer to AC 133-1A, Rotorcraft External-Load Operations in Accordance with FAR Part 133, for further information on airworthiness and flight manual policy for operators.
AC 27.25A. § 27.25 (Amendment 27-44) WEIGHT LIMITS.
a. Explanation. Amendment 27-44 adds a requirement to create weight, altitude, and temperature limitations for those rotorcraft that are not able to meet the basic requirements of §§ 27.79 or 27.143(c). The § 27.79 height-velocity diagram must be demonstrated at maximum weight or at the highest weight allowing out-of-ground-effect (OGE) hover at a density altitude of 7,000 feet. The § 27.143(c) controllability must be demonstrated at critical weight at 7,000 feet density altitude. If either or both of these
Page B – 4
requirements cannot be met, the applicant must have in place the appropriate limitations to assure that take-offs and landings are limited to those weights, altitudes, and temperatures, plus any associated wind constraints, for which satisfactory demonstration has been made. In no case should those limits be established at an altitude that is not operationally suitable. In the past, the minimum operationally suitable altitude for takeoff and landing has been established as 3,000 feet density altitude.
b. Procedures. The policy material pertaining to the procedures outlined in this section remain in effect.
Page B – 4.1
SUBPART B - FLIGHT › 27.27 (Amendment 27-2) CENTER OF GRAVITY LIMITS
AC 27.27.§ 27.27 (Amendment 27-2) CENTER OF GRAVITY LIMITS.
a. Explanation.
(1) This regulation is definitive and requires that the center of gravity limits be defined. Proof of compliance with all applicable flight requirements is required within the range of established CG’s. Along with the longitudinal CG limits, the lateral CG limits should either be established or determined to be not critical.
(2) Ballast is usually carried during the flight test program to investigate the approved gross weight/center of gravity limits. Lead is the most commonly used form of ballast during rotorcraft flight testing although other types of ballast, such as water, may serve just as well. Water may have the added benefit of being jettisonable during critical flight test conditions. Care must be taken regarding the location of ballast. The strength of the supporting structures should be adequate to support such ballast during the flight loads that may be imposed during a particular test and for the ultimate inertia forces of § 29.561(b)(3). Of critical importance is the method of securing the ballast to the desired locations. To avoid any undesired in-flight movements of the ballast, a positive method of constraint is mandatory. The flight test crews should also visually verify the amount, location, and integrity of the ballast. The effects of mass moment of inertia on the flight characteristics due to the ballast locations should also be considered. The mass moment of inertia of the test rotorcraft should, to the extent possible, be the same as that expected in normal, approved loadings, especially during tests involving dynamic inputs.
b. Procedures.
(1) Center of gravity locations and limits are of prime importance to rotorcraft stability and safety in flight. The primary concern is establishment of the longitudinal center of gravity limits. Lateral center of gravity limits with respect to longitudinal center of gravity limits are also important. The design of the rotorcraft is usually such that approximate lateral symmetry exists. This lateral symmetry can be upset by numerous probable lateral loadings possibly resulting in the necessity to establish lateral center of gravity limits. Stability and control characteristics may be seriously affected by loading outside the established center of gravity limits. The established center of gravity limits must be that as fuel is consumed, it is possible for the rotorcraft to remain within the established limits by acceptable loading and/or operating instructions.
(2) Structural limits may restrict the maximum forward longitudinal center of gravity limits. However, in most cases it is the maximum value established wherein adequate low speed control power exists to meet such requirements as § 27.143(c). Likewise, the maximum aft center of gravity limit may be a “structural limit,” but it usually is determined during flight test after the rotorcraft’s handling qualities tests have been conducted. Flight tests may reduce the “structural limit” CG envelope, but flight tests alone should not be used to expand the “structural limit.” Additional items which may influence the maximum aft center of gravity limits may be malfunctions of automatic
Page B – 4.2
stabilization equipment, excessive rotorcraft attitudes during critical phases of flight, or adequate control power to compensate for an engine failure.
(3) Lateral center of gravity limits have become more critical because of the ever increasing utilization of the rotorcraft for such things as unusual and unsymmetric lateral loads, both internal and external. Maximum allowable lateral center of gravity limits have also influenced the results of the unusable fuel determination.
(4) In summary, it is of prime importance that longitudinal and lateral center of gravity limits be determined so that unsafe conditions do not exist within the approved altitude, airspeed, ambient temperature, gross weight, and rotor RPM ranges. All relevant malfunctions must be considered.
Page B – 5
SUBPART B - FLIGHT › 27.29 (Amendment 27-14) EMPTY WEIGHT AND CORRESPONDINGCENTER OF GRAVITY
AC 27.29. § 27.29 (Amendment 27-14) EMPTY WEIGHT AND CORRESPONDING
CENTER OF GRAVITY.
a. Explanation. The empty weight of the rotorcraft consists of the airframe, engines, and all items of operating equipment that have fixed locations and are permanently installed (including both required and optional equipment) in the rotorcraft. It includes fixed ballast, unusable fuel, other unusable fluids, and full operating fluids. “Full operating fluids” such as oils used in an engine, auxiliary power unit, main and auxiliary gearboxes, and hydraulic systems are considered “closed fluid systems” typically filled to a “full mark” indicator level. Fluids necessary for the operation of nonpermanently installed equipment (i.e., carry-on equipment) are not considered part of the empty weight.
(1) A ballast is fixed when made a permanent part of the rotorcraft as a means of controlling the empty weight center of gravity (CG).
(2) Installed equipment is any FAA-approved equipment attached to the rotorcraft with hardware and, as a result, becomes an integral part of the rotorcraft. The installation or removal of such equipment must be recorded in the aircraft equipment list. Compliance with paragraph (b) of § 27.29 is accomplished by the use of an equipment list specifying the installed equipment at the time of weighing and the weight arm and moment of the equipment.
b. Procedures.
(1) Determination of the empty weight and corresponding center of gravity is primarily the responsibility of the manufacturer and is normally made on a production rotorcraft rather than a prototype. If the manufacturer has been issued a production certificate and wishes to avoid weighing each production rotorcraft, the manufacturer may make a detailed proposal defining the procedures it would use to establish an empty weight and CG. When the proposal is approved, the manufacturer will weigh the first five to ten production rotorcraft and show that the rotorcraft will be within ±1 percent on empty weight and ±0.2 inches on CG. After this procedure is established, the empty weight and CG may be computed except that at regular intervals a rotorcraft will be weighed to ensure the tolerances are still being maintained (e.g., one in ten rotorcraft)
(2) For prototype and modified rotorcraft, it is only necessary to establish a known basic weight and CG position (by weighing) from which the extremes of weight and CG travel required by the test program may be calculated. See FAA-H-8083-1 (Pilots Weight and Balance Handbook) for a sample weight and balance procedure.
(3) The weight and balance should be recalculated if a modification (or series of modifications) to the rotorcraft results in a significant change to the empty weight. Additionally, this change in empty weight should be reflected with the weight and balance information contained in the Rotorcraft Flight Manual (RFM) or Rotorcraft Flight Manual Supplement (RFMS).
Page B – 6
c. Ballast Loading and Type.
(1) Ballast loading of the rotorcraft can be accomplished in any manner to achieve a specific CG location. It is acceptable for such ballast to be mounted outside the physical confines of the rotorcraft if the flight test objectives are not affected by this arrangement. In flight test work, loading problems will occasionally be encountered in which it will be difficult to obtain the desired CG limits. Such cases may require loading in engine compartments or other places not designed for load carrying. When this condition is necessary, care should be taken to ensure that local structural stresses are not exceeded or that the rotorcraft flight characteristics are not changed due to increased moments of inertia by attaching the ballast to extreme CG locations which may not be designed for the added weight.
(2) The two types of ballasts that may be used in loading are solid or liquid. The solids are usually high density materials such as lead while the liquid usually used is water. In critical tests, the ballast may be loaded in a manner so that disposal in flight can be accomplished. In any case, the load should be securely attached in its loaded position so shifting or interference with safety of flight will not result. not result.
Page B – 6.1
SUBPART B - FLIGHT › 27.31 REMOVABLE BALLAST
AC 27.31. § 27.31 REMOVABLE BALLAST.
a. Explanation. This regulation provides the option of using removable ballast to obtain desired center of gravity locations to determine compliance with the flight requirement of this Part. Fixed ballast used for flight operations after type certification must be documented in the type design data. Removable ballast is used primarily on small rotorcraft to control the CG with different passenger loadings although this regulation does not permit its use on transport rotorcraft. If removable ballast is used, the rotorcraft flight manual must include instructions regarding its use and limitations.
b. Procedures. None
Page B – 6.2
SUBPART B - FLIGHT › 27.33 (Amendment 27-14) MAIN ROTOR SPEED AND PITCH LIMITS
AC 27.33. § 27.33 (Amendment 27-14) MAIN ROTOR SPEED AND PITCH LIMITS.
a. Explanation.
(1) General. This section requires the establishment of power-on and power-off main rotor speed limits and the requirements for low rotor speed warning.
(2) Power-On. The power-on limits should be sufficient to maintain the rotor speed within these limits during any appropriate maneuver expected to be encountered in normal operations throughout the flight envelope for which certification is requested. In the past a minimum power-on range of approximately 3 percent has been required due to engine governor and engine operating characteristics. With the introduction of advanced engines and electronic engine controls, there may not be a need for a range. One fixed value may suffice. If substantiated, transient power-on values may also be acceptable.
(3) Power-Off. The power-off rotor speed limits should be sufficient to encompass the rotor speeds encountered during normal autorotative maneuvers except for final landing phase (touchdown) for which rotor RPM may be lower than the minimum transient limit for flight, provided stress limits are not exceeded. The limits should also be sufficient to cover the ranges of airspeed, weight, and altitudes for which certification is requested. It is not the intent of the rule to require the minimum and maximum limit values in conjunction with extremes such as maximum/minimum weights and/or high altitude. The minimum and maximum rotor speed requirements should be thoroughly evaluated at normal operating environment; i.e., at altitudes from approximately sea level to 10,000 feet, temperatures not at extremes, and weights as necessary for other tests and as required to readily establish the limit rotor speeds. Spot checks of the autorotative requirements should be made at the extremes of the flight envelope and environmental conditions during normal tests at those conditions.
Under conditions where high autorotative rotor speeds may be encountered, it is acceptable for the pilot to adjust the controls to prevent overspeeding of the rotor. At light weight combined with low altitudes and extremely cold temperatures, the normal low pitch setting may not be sufficient to maintain autorotational rotor speed values within limits. If this occurs, the manufacturer may elect to adjust the low pitch stops as a maintenance procedure at extreme ambient conditions provided the flight and maintenance manuals clearly present the rigging requirements and procedures. There must be sufficient “overlap” of ambient conditions between configurations such that rerigging is not required whenever ambient temperature and surface elevation change slightly. Any downrigging of the low pitch stop must continue to ensure adequate clearance between controls and other rotorcraft structure and should be evaluated during flight test.
Both the power-on and power-off limits may also be established by encountering critical flapping limits in some approved flight conditions such as high airspeed or sideward flight.
(4) Low Speed Warning. If it is possible under expected operating conditions for the rotor speed to fall below the minimum approved values, the requirement exists
Page B – 7
for a low rotor speed warning. This warning is required on all single-engine rotorcraft and on multiengine rotorcraft where there is not an automatic increase in remaining engine(s) power output upon failure of an engine. Although not required by the rule, essentially all of today’s multiengine rotorcraft have a low rotor speed warning system installed. If the minimum power-on and power-off rotor speed limits are different, the warning signal should be at the higher speed, normally the power-on minimum rotor speed. One type of rotorcraft has a warning system cutout if the collective is full down, and other types have other warnings on the engine speed to indicate engine failure. All of these related warning systems must be evaluated with emphasis on ensuring adequate rotor speed.
b. Determination and Testing. Refer to paragraph AC 27.1509 (§ 27.1509) for additional information on determining and testing rotor limits.
Page B – 8
SUBPART B - FLIGHT › 27.45 (Amendment 27-14) PERFORMANCE - GENERAL
SUBPART B - FLIGHT
PERFORMANCE
AC 27.45. § 27.45 (Amendment 27-14) PERFORMANCE - GENERAL.
a. Explanation.
(1) Section 27.45 of 14 CFR regulations lists the rules and standards under which the performance requirements are to be met. This guidance provides general guidelines that may be used throughout a flight test program. It is impossible to find ideal test conditions and there are many variables that affect the flight test results that must be taken into account. Some of these variables are wind, temperature, altitude, humidity, rotorcraft weight, power, rotor RPM, center of gravity, etc. A thorough knowledge of the testing procedures and data reduction methods is essential and good engineering judgment must be used to determine acceptable test conditions. The test results should be analyzed and expanded by an approved methodology. The guidance within this section is considered an approved methodology.
(2) Performance should be based on approved engine power as determined in paragraph b.(5) below and not on any transient limits. Approved transient limits are basically for inadvertent overshoots of approved operational limits, and any sustained operation in these transient limit areas usually requires some form of special maintenance. However, for such demonstrations as landing procedure demonstration and HV determination, low rotor speeds (within approved limits) have been authorized. Such transients, if authorized, must be flight evaluated.
(3) Where variations in the parameter on which a tolerance is allowed will have an appreciable effect on the test, the results should be corrected to the standard value of the parameter; otherwise, no correction is necessary.
(4) The 30-second and 2-minute OEI power ratings, defined in 14 CFR 1.1, are based on up to three periods of use during a single flight. The purpose of the three periods is (i) to initially recover from an engine failure, (ii) to conduct OEI missed approach, and (iii) to conduct the final OEI landing. Rotorcraft performance based on the use of these time-limited power ratings is only permitted once in each of the above three periods (i.e., 30-second power must not be used more than once during the initial recovery from an engine failure).
(5) All engines operating (AEO) performance must be based upon approved AEO power ratings. OEI power ratings cannot be applied to an AEO condition.
b. Procedures.
(1) Winds for Testing.
Page B - 9
(i) Allowable wind conditions will vary with the type of test and will also be different for different types and gross weight rotorcraft. For example, higher winds can usually be tolerated for takeoff and landing tests than for hover performance. Higher winds can sometimes be tolerated during hover performance testing on rotorcraft with high rotor downwash velocities. Generally, unless the effects of wind on hover performance tests can be determined and accounted for, hover performance testing should be conducted in winds of 3 knots or less.
(ii) IGE controllability and maneuverability testing should be conducted in surface winds of less than 5 knots, or when higher steady wind conditions exist, with a maximum gust spread of 5 knots.
(iii) As can be seen from the foregoing, there is no such thing as an exact allowable wind for a particular test or rotorcraft. The flight test team must decide on the allowable wind for each condition based on all available information and their engineering judgment. The following summary of allowable wind conditions is given for general guidance only:
(A) Hover performance - 0 to 3 knots.
(B) HV - 0 to 5 knots.
(C) IGE controllability and maneuverability - 0 to 5 knots.
(iv) A means should be provided to measure the wind velocity, direction, and ambient air temperature at the rotor height for any particular tests.
(2) Altitude Effects: Extrapolation and Interpolation.
(i) Using FAA//AUTHORITY approved methodology:
(A) Hover performance may be extrapolated from test data up to a maximum of ±4,000 feet density altitude from the test altitude.
(B) IGE handling qualities, height-velocity, and engine operating characteristics may be extrapolated from test data up to a maximum of ±2,000 feet density altitude from the test altitude.
(C) Cruise stability and controllability tests should be evaluated at a minimum at two different altitudes, the lowest practical altitude and approximately the highest cruise altitude requested for approval. This can allow an interpolation of approximately 10,000 feet density altitude.
Page B - 10
(ii) As in all testing, extrapolation or interpolation should only be considered if all available information and engineering judgment indicate that regulatory compliance can be met at the untested conditions.
(3) Altitude Limitations.
Explanation. Two altitudes are normally presented in the RFM to define the operating envelope of a rotorcraft: maximum operating altitude and maximum takeoff and landing altitude.
(A) Maximum operating altitude is an operating limitation required by § 27.1527 and delineates the maximum altitude to which operation is allowed. This altitude normally constitutes the maximum cruise or enroute altitude.
(B) Maximum takeoff and landing altitude may be limited by the IGE hover ceiling for a rotorcraft as described in § 27.73 (through Amendment 27-14) or by low speed controllability. The hover ceiling and any information pertinent to takeoff and landing are presented in the performance information section of the RFM. For rotorcraft certificated to CAR 6, Amendment 6-7 or any amendment of part 27, a hover ceiling may not be presented above the altitude at which takeoff, HV, and IGE controllability tests were conducted plus allowable extrapolation, unless that extrapolated altitude is to at least 7,000 feet. If the applicant elects to demonstrate these tests to an altitude below 7,000 feet, including allowable extrapolation, then that altitude is the maximum takeoff and landing altitude of the rotorcraft. The maximum takeoff and landing altitude may be coincident with, but never above the maximum operating altitude limitation. Takeoff and landing and hover ceiling data and presentation requirements are presented in §§ 27.51, 27.73, and 27.1587.
(ii) Procedures.
Continue reading ↓ 120 of 2948 passages shown