AC 29-2C Certification of Transport Category Rotorcraft (Changes 1 - 9 incorporated)
a. This revision makes needed changes to this Advisory Circular (AC). b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
TIPS ON USING BOOKMARKS IN THIS
DOCUMENT
We have added a new feature that should help you to move around more quickly in the advisory circular.
On the upper left side, click on “Bookmarks.” You can click on any line that has a plus sign (+) beside it and it will expand to show you everything that comes under that particular section. You can click on any bookmark and you will go directly to that paragraph.
0 Advisory U.S. Department of Transportation Federal Aviation Circular Administration
Subject: Certification ofTransport Date: 6/23/23 AC No: 29-2C Category Rotorcraft Initiated By: AIR-600 Change: 9
1. PURPOSE.
a. This revision makes needed changes to this Advisory Circular (AC).
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
2. PRINCIPAL CHANGES.
This Change 9 includes changes, edits, and additions for these AC sections: 29.955, 29.997, 29.1019, 29.1305, 29.1309, 29.1329, 29.1333, 29.1335, 29.1353, 29.1517, 29.1543, 29.1545, 29.1549, 29.1555, 29.1587, and AC 29 Appendix B.
The contents of this guidance document do not have the force and effect oflaw and are not meant to bind the public in any way. This guidance document is intended only to provide clarity to the public regarding existing requirements under the law or agency policies.
3. WEBSITE AVAILABILITY.
To access this AC electronically, you can go to either of the following sites:
http:/ /www.faa.gov/regulations policies/advisory circulars/
https://drs.faa.gov/browse
Digitally signed by VICTOR W WICKLUND Date: 2023.06.23 16:30:39 -04'00' Victor Wicklund, Acting Director, Policy & Standards Division Aircraft Certification Service
Advisory U.S. Department of Transportation Circular Federal Aviation Administration
Subject: Certification of Transport Category Date: 07/02/2018 AC No: 29-2C Rotorcraft Initiated By: AIR-680 Change: 8
1. PURPOSE.
a. This Advisory Circular (AC) publishes needed changes to the existing Advisory Circular (AC) material.
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
2. PRINCIPAL CHANGES. This change 8 includes changes, edits, and additions for section 29.773.
PAGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
D-68 9/30/1999 D-68.1, D-68.2 07/02/18
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
Dr. Michael C. Romanowski Director, Policy and Innovation Division Aircraft Certification Service
C
Advisory
US Department orTransportation Circular Federal Aviation Administration
Subject: CERTIFICATION OF TRANSPORT Date: FEB 4 2016 AC No: 29-2C CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 7
1. PURPOSE.
a. This change publishes needed changes to the existing material and adds Miscellaneous Guidance (MG) sections to the Advisory Circular (AC).
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
2. PRINCIPAL CHANGES.
a. This change 7 includes changes, edits, and additions for these AC sections: 29.865B, 29.1303, 29.1321, 29 MG 1, 29 MG 16, and 29 Appendix B.
b. This change adds to this AC the following MG sections: AC 29 MG 19 (Guidance on Electronic Display Systems (EDS) for Rotorcraft Installations), AC 29 MG 20 (Human Factors (HF)), and AC 29 MG 21 (Guidance on Creating a System Level Functional Hazard Assessment (FHA)).
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations policies/advisory circulars/.
anager, Rotorcraft Directorate, Aircraft Certification Service
U.S. Deportment of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF TRANSPORT Date: 7/25/2014 AC No: 29-2C CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 6
1. PURPOSE.
a. This Advisory Circular (AC) change publishes the new guidance on automatic flight guidance and control systems (AFGCS) installation in part 29 rotorcraft.
b. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES. This change adds the miscellaneous guidance section 23 (MG 23), Automatic Flight Guidance and Control Systems (AFGCS) Installation in Part 29 Rotorcraft., to the AC.
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
/s/ Lance T. Gant, for Kim Smith Manager, Rotorcraft Directorate, Aircraft Certification Service
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF TRANSPORT Date: 6/13/2014 AC No: 29-2C CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 5
1. PURPOSE.
a. This Advisory Circular (AC) change publishes the new guidance on analyzing an advanced flight controls (AdFC) system installation in transport category rotorcraft.
b. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES. This change adds the miscellaneous guidance section 17 (MG 17), Guidance on Analyzing an Advanced Flight Controls (AdFC) System, to the AC.
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
/s/ Kim Smith Kim Smith Manager, Rotorcraft Directorate, Aircraft Certification Service
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF TRANSPORT Date: 5/1/2014 AC No: 29-2C CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 4
1. PURPOSE.
a. This Advisory Circular (AC) publishes needed changes to the existing AC material. Additionally, there is incorporation of previously approved AC material and non-technical editorial changes to various sections.
b. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the outside margin indicate the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
c. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES.
a. The AC sections previously approved on September 17, 2009 and posted separately to the Regulatory and Guidance Library (RGL), which are related to the Rotorcraft Performance and Handling Qualities rulemaking, are incorporated in this change 4. Those AC sections that were added or changed are: 29.25A, 29.49, 29.143A, 29.173A, 29.175A, 29.177A, 29.1587B, and 29 Appendix B.
b. The changed AC 29 Miscellaneous Guidance (MG) 5 section (Agricultural Dispensing Equipment Installation), previously approved on December 15, 2009 and posted separately to the Regulatory and Guidance Library (RGL), is incorporated in this change 4.
c. The AC 29.573 section previously approved on December 1, 2011 and posted separately to the Regulatory and Guidance Library (RGL), which is related to the Damage Tolerance and
Fatigue Evaluation of Composite Rotorcraft Structures rulemaking, is incorporated in this change 4.
d. The AC 29.571B section previous approved on December 2, 2011 and posted separately to the Regulatory and Guidance Library (RGL), which is related to the Fatigue tolerance Evaluation of Metallic Structure rulemaking, is incorporated in this change 4.
e. The changed AC 29.972 and 29.927A sections (Additional Tests for Rotor Drive Systems), previously approved on July 6, 2012 and posted separately to the Regulatory and Guidance Library (RGL), are incorporated in this change 4.
f. The changed AC 29 MG 6 section (Emergency Medical Service (EMS) Systems Installations Including: Interior Arrangements, Equipment, Helicopter Terrain Awareness and Warning System (HTAWS), Radio Altimeter, and Flight Data Monitoring System), previously approved on February 27, 2014, is incorporated in this change 4.
g. The changed AC 29 MG 18 section on (Helicopter Terrain Awareness and Warning System (HTAWS)), previously approved on February 27, 2014, is incorporated in this change 4.
h. This change 4 also includes changes, edits, and additions for these AC sections: 29.29, 29.45, 29.49, 29.79, 29.141, 29.143, 29.151, 29.251, 29.337, 29.561, 29.562, 29.563A, 29.571A, 29.603, 29.610, 29.625, 29.801, 29.855A, 29.863, 29.865, 29.865B, 29.871, 29.903B, 29.923B, 29.939, 29.1011, 29.1093, 29.1093A, 29.1193, 29.1309, 29.1316, 29.1317, 29.1329, 29.1333, 29.1337, 29.1351, 29.1357, 29.1401, 29.1411, 29.1435. 29.1501, 29.1527, 29.1541, 29.1543, 29.1549, 29.1583, 29 MG 1, 29 MG 2, 29 MG 4, 29 MG 8, 29 MG 13, 29 MG 18, 29 MG 22, and 29 Appendix A.
3. WEBSITE AVAILABILITY. To access this AC electronically, go to the Advisory Circulars library at http://www.faa.gov/regulations_policies/advisory_circulars/.
/s/ Lance T. Gant, for Kim Smith Manager, Rotorcraft Directorate, Aircraft Certification Service
US Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF TRANSPORT Date: 9/30/2008 AC No:29-2C CATEGORY ROTORCRAFT Initiated by: ASW-110 Change: 3
1. PURPOSE.
a. This Advisory Circular (AC) publishes needed changes to the existing AC material as a result of a safety-focused study.
b. This change revises existing material in 9 sections.
c. The change number and the date of the changed material are shown at the top of each page. The vertical lines in the right or left margin indicates the beginning and end of each change. Pages that have different page numbers, but no text changes, will retain the previous heading information.
d. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
2. PRINCIPAL CHANGES. Sections 29.571, 29.679, 29.695, 29.783, 29.901A, 29.917A, 29.1307, 29.1351, and 29.1431 are revised.
3. WEBSITE AVAILABILITY. To access this AC electronically, log on to http://www.airweb.faa.gov/rgl and then click on AC’s.
AC 29-2C, Chg 3 PAGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
vii thru x … 2/12/03 & 4/25/06 xiii & xiv … 2/12/03 & 4/25/06 C-93 thru C-96 … 9/30/99 & 2/12/03 D-41 thru D-44 … 9/30/99 & 4/25/06 D-47 & D-48 … 9/30/99 D-79 thru D-82 … 9/30/99 E-7 & E-8 … 9/30/99 E-35 thru 38 … 9/30/99 & 4/25/06 F-11 & F-12 … 9/30/99 & 2/12/03 F-65 & F-66 … 9/30/99 F-113 thru F-116 … 9/30/99
vii thru x … 2/12/03, 4/25/06, & 9/30/08 xiii thru xiv … 9/30/08 C-93 thru C-96 … 2/12/03 & 9/30/08 D-41 thru D-44 … 9/30/08 D-47 thru D-48 … 9/30/99 & 9/30/08 D-79 thru D-82 … 9/30/08 E-7 & E-8 … 9/30/99 & 9/30/08 E-35 thru E-38 … 9/30/99 & 9/30/08 F-11 & F-12 … 9/30/08 F-65 thru F-66.2 … 9/30/08 F-113 thru F-116 … 9/30/99 & 9/30/08
Signed by Scott A. Horn for
Mark R. Schilling Acting Manager, Rotorcraft Directorate
Aircraft Certification Service
Page
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF TRANSPORT
CATEGORY ROTORCRAFT
Date: Initiated
4/25/06 ASW-110
AC No: 29-2C Change: Chg 2 … 4. PURPOSE.
a. This change incorporates all the previously revised AC paragraphs that were posted as accepted and finalized AC material on the FAA RGL website since 2/12/03.
b. This change revises existing material in 25 paragraphs and adds new material for one paragraph.
c. The change number and the date of the changed material are shown at the top of each page that contains changed text. The vertical lines in the right and left margins indicate the beginning and end of each change. Pages that have different page numbers but no text changes will retain the previous heading information.
d. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
5. PRINCIPAL CHANGES.
a. Paragraphs 29.45, 29.59A, 29.75A, 29.337, 29.351B, 29.547A, 29.602, 29.631, 29.672, 29.683, 29.777, 29.917A, 29.1321, 29.1333, 29.1351, 29.1585, MG 1, MG 4, MG 8, MG16, Appendix A, and Appendix B are revised.
b. The AC material in paragraphs 29.801 and 29.1411 has been revised.
c. The AC material in MG 12 has been revised and is now contained in AC 29.865B, Subpart D.
d. New paragraph MG 18, Helicopter Terrain Awareness Warning System (HTAWS), is added to Chapter 3.
e. New figures AC 29.351A-1, 29.351B-1, 29.351B-2, and 29.865B-1 are added in Chapter 2.
f. New figures AC 29 MG 8-1, 8-2, 8-3, 8-4, 18-1, 18-2, and 18-2.1 are added in Chapter 3.
6. WEBSITE AVAILABILITY. To access this AC electronically, log on to http://www.airweb.faa.gov/rgl and then click on AC’s.
AC 29-2C, Chg 2 PAGE CONTROL CHART Remove Pages Dated Insert Pages Dated iii thru x … 9/30/99 & 2/12/03 xiii thru xxiv … 9/30/99 & 2/12/03 B-11 thru B-20 … 9/30/99 B-49 thru B-125 … 9/30/99 C-5 thru C-6 … 9/30/99 C-13 thru C-96 … 9/30/99 & 2/12/03 D-1 thru D-159 … 9/30/99 & 2/12/03 E-37 thru E-48 … 9/30/99 F-43 thru F-44 … 9/30/99 F-61 thru F-120 … 9/30/99 & 2/12/03 G-45 thru G-52 … 9/30/99 MG 1-15 thru MG 1-17 … 9/30/99 MG 4-9 thru MG 4-13 … 9/30/99 MG 8-1 thru MG 8-15 … 9/30/99 & 2/12/03 MG 12-1 thru MG 12-44…...9/30/99 & 2/12/03 MG 16-1 thru MG 16-16 … 2/12/03 none none Apdx A-47 thru Apdx A-70 … 2/12/03 Apdx B-11 thru Apdx B-20...9/30/99 & 2/12/03
iii thru x … 4/25/06 xiii thru xxv … 4/25/06 B-11 thru B-20 … 4/25/06 B-49 thru B-127 … 4/25/06 C-5 thru C-6 … 4/25/06 C-13 thru C-98 … 4/25/06 D-1 thru D-185 … 4/25/06 E-37 thru E-48 … 4/25/06 F-43 thru F-44 … 4/25/06 F-61 thru F-123 … 4/25/06 G-45 thru G-52 … 4/25/06 MG 1-15 thru MG 1-16 … 4/25/06 MG 4-9 thru MG 4-13 … 4/25/06 MG 8-1 thru MG 8-31 … 4/25/06 MG 12-1 … 4/25/06 MG 16-1 thru MG 16-18 … 4/25/06 MG 17-1 … 4/25/06 MG 18-1 thru MG 18-27 … 4/25/06 Apdx A-47 thru Apdx A-71 … 4/25/06 Apdx B-11 thru Apdx B-21 … 4/25/06
David A. Downey Manager, Rotorcraft Directorate
Aircraft Certification Service
Page
U.S. Department of Transportation
Federal Aviation Administration
Advisory Circular
Subject: CERTIFICATION OF TRANSPORT
CATEGORY ROTORCRAFT
Date: Initiated
2/12/03 ASW-110
AC No: 29-2C Change: Chg 1 … 7. PURPOSE.
a. This change revises existing material in 21 paragraphs and adds new material for seven paragraphs.
b. The change number and the date of the changed material are shown at the top of each page that contains changed text. The vertical lines in the right and left margins indicate the beginning and end of each change. Pages that have different page numbers but no text changes will retain the previous heading information.
8. CANCELLATION.
a. AC 20-95, Fatigue Evaluation of Rotorcraft Structure, May 18, 1976, is canceled in its entirety.
b. AC 20-137, Dynamic Evaluation of Seat Restraint Systems & Occupant Restraint for Rotorcraft (Normal and Transport), March 30, 1992, is canceled in its entirety, and is replaced by material contained in AC 29.562.
c. AC test containing references to AC 20-95 and AC 20-137 was either changed or deleted in paragraphs AC 29.2, 29.562, 29.613, 29.785A, 29.865A, 29.907, 29.952, MG 8, and MG 12.
9. PRINCIPAL CHANGES.
a. Paragraphs 29.562, 29.571, 29.805, 29.1303, 29.1309, 29.1353, 29.1419, 29.1505, 29.1529, MG 5, MG 6, MG 11, MG 12, and Appendix B are revised.
b. New paragraphs 29.625A and 29.785B are added to Chapter 2.
c. New paragraphs MG 13, MG 14, MG 15, and MG 16 are added to Chapter 3.
d. Appendix A (previously reserved) is added.
e. New figures AC 29.562-1, 29.562-2, 29.562-3, 29.562-4, 29.562-5, 29.562-6, 29.562-7, 29.562-8, 29.1309-1, 29.1309-2, 29.1309-3, 29.1309-4, and 29.1309-5 are added in Chapter 2.
f. New figures AC 29 MG 11-2, 11-4, 11-5, 14-1, 15-1, and 15-2 are added in Chapter 3.
10. WEBSITE AVAILABILITY. To access this AC electronically, log on to http://www.airweb.faa.gov/rgl and then click on AC’s.
AC 29-2C, Chg 1 PAGE CONTROL CHART Remove Pages Dated Insert Pages Dated v thru x … 9/30/99 xiii thru xxiii … 9/30/99 A-3 thru A-4 … 9/30/99 C-51 thru C-58 … 9/30/99 D-13 thru D-14 … 9/30/99 D-27 thru D-30 … 9/30/99 D-85 thru D-100 … 9/30/99 D-133 thru D-134 … 9/30/99 E-29 thru E-30 … 9/30/99 E-57 thru E-58 … 9/30/99 E-69 thru E-70 … 9/30/99 E-75 thru E-80 … 9/30/99 F-1 thru F-105 … 9/30/99 G-3 thru G-50 … 9/30/99 MG 5-1 thru MG 5-6 … 9/30/99 MG 6-5 thru MG 6-18 … 9/30/99 MG 8-5 thru MG 8-6 … 9/30/99 MG 11-1 thru MG 11-25 … 9/30/99 MG 12-23 thru MG 12-24 … 9/30/99 MG 12-37 thru MG 12-38 … 9/30/99 MG 12-43 thru MG 12-44 … 9/30/99 none none none none none Apdx B-13 thru Apdx B-14 … 9/30/99
v thru x … 2/12/03 xiii thru xxiv … 2/12/03 A-3 thru A-4 … 2/12/03 C-51 thru C-96 … 2/12/03 D-13 thru D-14 … 2/12/03 D-27 thru D-30 … 2/12/03 D-85 thru D-100 … 2/12/03 D-133 thru D-134 … 2/12/03 E-29 thru E-30 … 2/12/03 E-57 thru E-58 … 2/12/03 E-69 thru E-70 … 2/12/03 E-75 thru E-80 … 2/12/03 F-1 thru F-120 … 2/12/03 G-3 thru G-52 … 2/12/03 MG 5-1 thru MG 5-6 … 2/12/03 MG 6-5 thru MG 6-20 … 2/12/03 MG 8-5 thru MG 8-6 … 2/12/03 MG 11-1 thru MG 11-22 … 2/12/03 MG 12-23 thru MG 12-24 … 2/12/03 MG 12-37 thru MG 12-38 … 2/12/03 MG 12-43 thru MG 12-44 … 2/12/03 MG 13-1 thru 13-6 … 2/12/03 MG 14-1 thru 14-8 … 2/12/03 MG 15-1 thru 15-18 … 2/12/03 MG 16-1 thru 16-16 … 2/12/03 Apdx A-1 thru Apdx A-70 … 2/12/03 Apdx B-13 thru Apdx B-14 … 2/12/03
David A. Downey Manager, Rotorcraft Directorate
Aircraft Certification Service
Advisory Circular
…
U.S. Department of Transportation
Federal Aviation Administration
Subject: CERTIFICATION OF TRANSPORT Date: 9/30/99 AC No: 29-2C CATEGORY ROTORCRAFT Initiated by: ASW-110 Change:
1. PURPOSE:
a. This is a total revision of AC 29-2B dated 7/30/97, with Change 1 dated 9/30/98, incorporated. In addition, new material plus changes to existing paragraphs are incorporated. This consolidated version is now renumbered as AC 29-2C and replaces AC 29-2B in its entirety. This revises existing material in 12 paragraphs, adds new material for two paragraphs, and renumbers paragraphs to correspond with Federal Aviation Regulations (FAR) numbering.
b. Requests from the rotorcraft industry to make the document easier to use resulted in renumbering the AC paragraphs to correspond with FAR numbering. The figure numbers are also renumbered accordingly.
c. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This AC establishes an acceptable means, but not the only means, of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.
d. This advisory circular provides information on methods of compliance with 14 CFR Part 29, which contains the Airworthiness Standards for Transport Category Rotorcraft. It includes methods of compliance in the areas of basic design, ground tests, and flight tests.
2. CANCELLATION. AC 29-2B, Certification of Transport Category Rotorcraft, dated 7/30/97, is canceled in its entirety.
3. BACKGROUND. Based largely on precedents set during rotorcraft certification programs spanning over 40 years, this AC consolidates guidance contained in earlier correspondence among FAA headquarters, foreign authorities, the rotorcraft industry, and certificating regions.
4. PRINCIPAL CHANGES:
a. Chapter 3 is now titled "Miscellaneous Guidance (MG), Transport Category Rotorcraft," with the following changes:
• Paragraphs that correspond to a FAR number are merged into existing AC text in Chapter 2.
• Paragraphs that do not correspond with a FAR number either remain in Chapter 3 and are renumbered as MG paragraphs, or are now an appendix.
• In order to stay aligned with FAR numbering, Appendices A, C, and D are reserved for future AC material.
b. Paragraphs revised to incorporate technical guidance are AC 21.35, 29.561, 29.610, 29.863, 29.952, 29.1093, 29.1305, 29.1309, 29.1351, 29.1353, and MG 4 (FADEC). Paragraph AC 29.661, Rotorblade Clearance, contains new material added as a result of National Transportation Safety Board (NTSB) recommendations.
c. New paragraphs added are 29.602, Critical Parts, and MG 12, External Loads. These paragraphs correspond with recent harmonized regulatory changes. Also, figure 29.863-1 is new.
d. The AC is now divided by Subparts and page numbers reflect the relevant FAR Subpart.
e. “FAA/AUTHORITY” as used in this document means FAA or another airworthiness authority that has adopted this AC as a means of compliance with the appropriate regulation referenced.
5. DEVIATIONS. As rotorcraft designs vary from conventional configurations, it may become necessary to deviate from the methods and procedures outlined in this AC. These procedures are only one acceptable means of compliance with Part 29. Any alternate means proposed by an applicant will be given due consideration. Applicants are encouraged to use their technical ingenuity and resourcefulness to develop more efficient and less costly methods of achieving the objectives of Part 29. Regulatory personnel and designees should respond to such efforts by the use of engineering judgment in fostering any such efforts as long as the letter and spirit of Part 29 and the Federal Aviation Act are respected. It is recommended that unusual or unique projects be coordinated a sufficient time in advance with the Rotorcraft Standards Staff, ASW-110, or the appropriate airworthiness authority, to ensure timely and uniform consideration.
6. APPLICABILITY. This material is not to be construed as having any legally binding status and must be treated as advisory only. However, to ensure standardization in the certification process, these procedures should be considered during all rotorcraft type certification and supplemental type certification activities.
7. PARAGRAPHS KEYED TO FAR PART 29. Each paragraph has the applicable amendment to Part 29 shown in the title. All of the original guidance material has been retained as appropriate, even as changes are made to the regulations. This is accomplished through the use of “A,” “B,” etc., paragraphs, which follow the original numbered paragraphs. These subsequent paragraphs provide updated guidance information or changes to policy that parallel a specific rule change. The guidance material in the original paragraph (for earlier amendments) still applies and is modified as explained in each of the later paragraphs for later amendments. The applicable amendment number will only appear in the title line for the “A,” “B,” etc., paragraphs. The guidance material in the initial paragraph is intended to apply to all amendments except as modified by the later paragraphs. Each ensuing “A,” “B,” etc., paragraph will be identified with an amendment level to indicate the rule change that precipitated the policy change.
8. RELATED PUBLICATIONS. FAA Certification personnel and designees should be familiar with Order 8110.4, Type Certification, and Order 8100.5, Aircraft Certification Directorate Procedures.
Eric Bries Acting Manager, Rotorcraft Directorate
CONTENTS
Page No.
CHAPTER 1 - PART 21 CERTIFICATION PROCEDURES FOR
Untitled
PRODUCTS AND PARTS
AC 21.16 Special Conditions … FAR 21-1 AC 21.31 Type Design … FAR 21-2 AC 21.33 Inspection and Tests … FAR 21-2 AC 21.35 Flight Tests … FAR 21-2 AC 21.39 Flight Test Instrument Calibration and Correction Report … FAR 21-6
CHAPTER 2 - PART 29 AIRWORTHINESS STANDARDS:
TRANSPORT CATEGORY ROTORCRAFT
SUBPART A - GENERAL
GENERAL
AC 29.1 Applicability … A-1 AC 29.1A Applicability … A-2 AC 29.2 Special Retroactive Requirements … A-3
SUBPART B - FLIGHT
GENERAL
AC 29.21 Proof of Compliance … B-1 AC 29.21A Proof of Compliance … B-3 AC 29.25 Weight Limits … B-3 AC 29.25A Weight Limits … B-4 AC 29.27 Center of Gravity Limits … B-5 AC 29.29 Empty Weight and Corresponding Center of Gravity … B-6 AC 29.31 Removable Ballast … B-8 AC 29.33 Main Rotor Speed and Pitch Limits … B-8
PERFORMANCE
AC 29.45 Performance - General … B-10 AC 29.45A Performance - General … B-20 AC 29.45B Performance - General … B-20 AC 29.49 Performance at Minimum Operating Speed … B-26.2
Page No.
SUBPART B - FLIGHT (continued)
PERFORMANCE (continued)
AC 29.51 Takeoff Data - General … B-29 AC 29.51A Takeoff Data - General … B-30 AC 29.53 Takeoff: Category A … B-31 AC 29.53A Takeoff: Category A … B-34 AC 29.55 Takeoff Decision Point: Category A … B-36 AC 29.59 Takeoff Path: Category A … B-36 AC 29.59A Takeoff Path, Distance and Rejected Takeoff, Ground Level and ... B-46
Elevated Heliport: Category A AC 29.63 Takeoff: Category B … B-57 AC 29.65 Climb: (All Engines Operating) … B-60 AC 29.65A Climb: (General and All Engines Operating) … B-61 AC 29.67 Climb: One Engine Inoperative … B-63 AC 29.67A Climb: One Engine Inoperative … B-65 AC 29.71 Rotorcraft Angle of Glide: Category B … B-66 AC 29.73 Performance at Minimum Operating Speed … B-69 AC 29.75 Landing … B-71 AC 29.75A Landing … B-80 AC 29.77 Balked Landing: Category A … B-91 AC 29.79 Limiting Height - Speed Envelope … B-92 AC 29.85 Balked Landing: Category A … B-100 AC 29.87 Limiting Height - Speed Envelope … B-101
FLIGHT CHARACTERISTICS
AC 29.141 Flight Characteristics – General … B-102 AC 29.143 Controllability and Maneuverability … B-104 AC 29.143A Controllability and Maneuverability … B-106 AC 29.151 Flight Controls … B-108 AC 29.161 Trim Control … B-109 AC 29.161A Trim Control … B-110 AC 29.171 Stability: General … B-110 AC 29.173 Static Longitudinal Stability … B-111 AC 29.173A Static Longitudinal Stability … B-111 AC 29.175 Demonstration of Static Longitudinal Stability … B-112.2 AC 29.175A Demonstration of Static Longitudinal Stability … B-116 AC 29.177 Static Directional Stability … B- AC 29.177A Static Directional Stability … B-116.5 AC 29.181 Dynamic Stability: Category A Rotorcraft … B-117
Page
Page No.
SUBPART B - FLIGHT (continued)
GROUND AND WATER HANDLING CHARACTERISTICS
AC 29.231 General (Ground and Water Handling Characteristics) … B-118 AC 29.235 Taxiing Condition … B-118 AC 29.239 Spray Characteristics … B-119 AC 29.241 Ground Resonance … B-120
MISCELLANEOUS FLIGHT REQUIREMENTS
AC 29.251 Vibration … B-125
SUBPART C - STRENGTH REQUIREMENTS
GENERAL
AC 29.301 Loads … C-1 AC 29.303 Factor of Safety … C-1 AC 29.305 Strength and Deformation … C-2 AC 29.307 Proof of Structure … C-2 AC 29.307A Proof of Structure … C-3 AC 29.309 Design Limitations … C-4
FLIGHT LOADS
AC 29.321 General - Flight Loads … C-5 AC 29.337 Limit Maneuvering Load Factor … C-5 AC 29.339 Resultant Limit Maneuvering Loads … C-8 AC 29.341 Gust Loads … C-8 AC 29.351 Yawing Conditions … C-10 AC 29.351A Yawing Conditions … C-13 AC 29.351B Yawing Conditions … C-15 AC 29.361 Engine Torque … C-18
CONTROL SURFACE AND SYSTEM LOADS
AC 29.391 Control Surface and System Loads - General … C-20 AC 29.391A Control Surface and System Loads - General … C-20 AC 29.395 Control System … C-20 AC 29.395A Control System … C-22 AC 29.397 Limit Pilot Forces and Torques … C-22 AC 29.399 Dual Control System … C-23 AC 29.401 Auxiliary Rotor Assemblies … C-23
Page
Page No.
SUBPART C - STRENGTH REQUIREMENTS (continued)
CONTROL SURFACE AND SYSTEM LOADS (continued)
AC 29.401A Auxiliary Rotor Assemblies … C-24 AC 29.403 Auxiliary Rotor Attachment Structure … C-25 AC 29.403A Auxiliary Rotor Attachment Structure … C-25 AC 29.411 Ground Clearance: Tail Rotor Guard … C-26 AC 29.413 Stabilizing and Control Surfaces … C-27 AC 29.413A Stabilizing and Control Surfaces … C-29 AC 29.427 Unsymmetrical Loads … C-29
GROUND LOADS
AC 29.471 Ground Loads - General … C-33 AC 29.473 Ground Loading Conditions and Assumptions … C-33 AC 29.475 Tires and Shock Absorbers … C-34 AC 29.477 Landing Gear Arrangement … C-34 AC 29.479 Level Landing Conditions … C-34 AC 29.481 Tail-Down Landing Conditions … C-36 AC 29.483 One-Wheel Landing Conditions … C-36 AC 29.485 Lateral Drift Landing Conditions … C-36 AC 29.493 Braked Roll Conditions … C-37 AC 29.497 Ground Loading Conditions: Landing Gear With Tail Wheels … C-37 AC 29.501 Ground Loading Conditions: Landing Gear With Skids … C-39 AC 29.501A Ground Loading Conditions: Landing Gear With Skids … C-40 AC 29.505 Ski Landing Conditions … C-41 AC 29.511 Ground Load: Unsymmetrical Loads on Multiple-Wheel Units … C-41
WATER LOADS
AC 29.519 Hull Type Rotorcraft: Water-Based, Amphibian … C-43 AC 29.521 Float Landing Conditions … C-45
MAIN COMPONENT REQUIREMENTS
AC 29.547 Main Rotor Structure … C-46 AC 29.547A Main Rotor and Tail Rotor Structure … C-46 AC 29.549 Fuselage and Rotor Pylon … C-50 AC 29.551 Auxiliary Lifting Surfaces … C-50
Page
Page No.
SUBPART C - STRENGTH REQUIREMENTS (continued)
EMERGENCY LANDING CONDITIONS
AC 29.561 Emergency Landing Conditions - General … C-51 AC 29.561A Emergency Landing Conditions - General … C-53 AC 29.561B Emergency Landing Conditions - General … C-54 AC 29.562 Emergency Landing Dynamic Conditions … C-55 AC 29.563 Structural Ditching Provisions … C-92 AC 29.563A Structural Ditching Provisions … C-92
FATIGUE EVALUATION
AC 29.571 Fatigue Evaluation of Flight Structure … C-94 AC 29.571A Fatigue Evaluation of Flight Structure … C-97 AC 29.571B Fatigue Tolerance Evaluation of Metallic Structure … C-98 AC 29.573 Damage Tolerance and Fatigue Evaluation of Composite … C-130
Rotorcraft Structures
SUBPART D - DESIGN AND CONSTRUCTION
GENERAL
AC 29.601 Design … D-1 AC 29.602 Critical Parts … D-2 AC 29.603 Materials … D-4 AC 29.605 Fabrication Methods … D-5 AC 29.607 Fasteners … D-5 AC 29.609 Protection of Structure … D-6 AC 29.610 Lightning and Static Electricity Protection … D-8 AC 29.611 Inspection Provisions … D-12 AC 29.613 Material Strength Properties and Design Values … D-13 AC 29.613A Material Strength Properties and Design Values … D-14 AC 29.619 Special Factors … D-17 AC 29.621 Casting Factors … D-17 AC 29.623 Bearing Factors … D-27 AC 29.625 Fitting Factors … D-28.1 AC 29.625A Fitting Factors … D-28.1 AC 29.629 Flutter … D-29 AC 29.629A Flutter and Divergence … D-29 AC 29.631 Bird Strike … D-31
Page
Page No.
SUBPART D - DESIGN AND CONSTRUCTION (continued)
ROTORS
AC 29.653 Pressure Venting and Drainage of Rotor Blades … D-32 AC 29.659 Mass Balance … D-32 AC 29.661 Rotor Blade Clearance … D-32 AC 29.663 Ground Resonance Prevention Means … D-34 AC 29.663A Ground Resonance Prevention Means … D-36
CONTROL SYSTEMS
AC 29.671 Control Systems - General … D-37 AC 29.672 Stability Augmentation, Automatic, and Power-Operated Systems... D-37 AC 29.673 Primary Flight Controls … D-38 AC 29.674 Interconnected Controls … D-39 AC 29.675 Stops … D-39 AC 29.679 Control System Locks … D-41 AC 29.681 Limit Load Static Tests … D-42 AC 29.683 Operation Tests … D-42 AC 29.685 Control System Details … D-43 AC 29.687 Spring Devices … D-45 AC 29.691 Autorotation Control Mechanism … D-45 AC 29.695 Power Boost and Power-Operated Control System … D-46
LANDING GEAR
AC 29.723 Shock Absorption Tests … D-49 AC 29.725 Limit Drop Test … D-52 AC 29.727 Reserve Energy Absorption Drop Test … D-52 AC 29.727A Reserve Energy Absorption Drop Test … D-53 AC 29.729 Retracting Mechanism, Landing Gear … D-53 AC 29.731 Wheels … D-55 AC 29.733 Tires … D-56 AC 29.735 Brakes … D-58 AC 29.737 Skis … D-59
FLOATS AND HULLS
AC 29.751 Main Float Buoyancy … D-61 AC 29.753 Main Float Design … D-61 AC 29.755 Hull Buoyancy … D-64 AC 29.757 Hull and Auxiliary Float Strength … D-65
Page
Page No.
SUBPART D - DESIGN AND CONSTRUCTION (continued)
PERSONNEL AND CARGO ACCOMMODATIONS
AC 29.771 Pilot Compartment … D-67 AC 29.773 Pilot Compartment View … D-68 AC 29.775 Windshields and Windows … D-74 AC 29.775A Windshields and Windows … D-74 AC 29.775B Windshields and Windows … D-74 AC 29.777 Cockpit Controls … D-75 AC 29.779 Motion and Effect of Cockpit Controls … D-76 AC 29.783 Doors … D-78 AC 29.783A Doors … D-82 AC 29.785 Seats, Safety Belts, and Harnesses … D-83 AC 29.785A Seats, Berths, Belts, Safety Belts, and Harnesses … D-85 AC 29.785B Seats, Berths, Litters, Safety Belts, and Harnesses … D-87 AC 29.787 Cargo and Baggage Compartments … D-88 AC 29.787A Cargo and Baggage Compartments … D-88 AC 29.801 Ditching … D-89 AC 29.803 Emergency Evacuation … D-97 AC 29.803A Emergency Evacuation … D-97 AC 29.805 Flightcrew Emergency Exits … D-98 AC 29.805A Flightcrew Emergency Exits … D-98 AC 29.807 Passenger Emergency Exits … D-99 AC 29.807A Emergency Exits … D-100 AC 29.809 Emergency Exit Arrangement … D-101 AC 29.809A Emergency Exit Arrangement … D-102 AC 29.811 Emergency Exit Marking … D-103 AC 29.811A Emergency Exit Marking … D-105 AC 29.812 Emergency Lighting … D-106 AC 29.813 Emergency Exit Access … D-106 AC 29.815 Main Aisle Width … D-108 AC 29.831 Ventilation … D-109 AC 29.833 Heaters … D-110
FIRE PROTECTION
AC 29.851 Fire Extinguishers … D-112 AC 29.853 Compartment Interiors … D-113 AC 29.855 Cargo and Baggage Compartments … D-115 AC 29.855A Cargo and Baggage Compartments … D-117 AC 29.859 Combustion Heater Fire Protection … D-117 AC 29.861 Fire Protection of Structure, Controls, and Other Parts … D-121 AC 29.861A Fire Protection of Structure, Controls, and Other Parts … D-124
Page ix
Page No.
SUBPART D - DESIGN AND CONSTRUCTION (continued)
FIRE PROTECTION (continued)
AC 29.863 Flammable Fluid Fire Protection … D-124
EXTERNAL LOAD ATTACHING MEANS
AC 29.865 External Load Attaching Means … D-129 AC 29.865A External Load Attaching Means … D-134 AC 29.865B External Load Attaching Means (SEE MG 12) … D-140
MISCELLANEOUS (DESIGN AND CONSTRUCTION)
AC 29.871 Leveling Marks … D-165 AC 29.873 Ballast Provisions … D-165 AC 29.877 Ice Protection … D-166
SUBPART E - POWERPLANT
GENERAL
AC 29.901 Installation … E-1 AC 29.901A Installation … E-8
GENERAL (continued)
AC 29.901B Installation … E-8 AC 29.903 Engines … E-9 AC 29.903A Engines … E-11 AC 29.903B Engines … E-12 AC 29.903C Turbine Engine Installation … E-13 AC 29.907 Engine Vibration … E-29 AC 29.908 Cooling Fans … E-29 AC 29.908A Cooling Fans … E-30
ROTOR DRIVE SYSTEM
AC 29.917 Design … E-33 AC 29.917A Design … E-34 AC 29.921 Rotor Brake … E-37.2 AC 29.923 Rotor Drive System and Control Mechanism Tests … E-39 AC 29.923A Rotor Drive System and Control Mechanism Tests … E-45 AC 29.923B Rotor Drive System and Control Mechanism Tests … E-52
Page x
6/23/23
AC 29.923C AC 29.927 AC 29.927A AC 29.931 AC 29.935 AC 29.939
AC 29.951 AC 29.952 AC 29.953 AC 29.954 AC 29.955 AC 29.955A AC 29.955B AC 29.957 AC 29.959 AC 29.961 AC 29.961A AC 29.963 AC 29.963A AC 29.963B AC 29.965 AC 29.967 AC 29.967A AC 29.969 AC 29.969A AC 29.971 AC 29.971A AC 29.973 AC 29.973A AC 29.975 AC 29.975A AC 29.975B AC 29.977 AC 29.979
AC 29-2C, Chg 9
Page No.
SUBPART E - POWERPLANT (continued)
ROTOR DRIVE SYSTEM (continued)
Rotor Drive System and Control Mechanism Tests … E-53 Additional Tests … E-54.1 Additional Tests … E-56 Shafting Critical Speeds … E-58 Shafting Joints … E-63 Turbine Engine Operating Characteristics … E-63
FUEL SYSTEM
Fuel System - General … E-66 Fuel System Crash Resistance … E-68 Fuel System Independence … E-93 Fuel System Lightning Protection … E-94 Fuel Flow … E-95 Fuel Flow … E-99 Fuel Flow … E-102.1 I Flow Between Interconnected Tanks … E-103 Unusable Fuel Supply … E-103 Fuel System Hot Weather Operation … E-104 Fuel System Hot Weather Operation … E-106 Fuel Tanks: General … E-107 Fuel Tanks: General … E-107 Fuel Tanks: General … E-108 Fuel Tank Tests … E-109 Fuel Tank Installation … E-111 Fuel Tank Installation … E-113 Fuel Tank Expansion Space … E-113 Fuel Tank Expansion Space … E-114 Fuel Tank Sump … E-114 Fuel Tank Sump … E-116 Fuel Tank Filler Connection … E-116 Fuel Tank Filler Connection … E-117 Fuel Tank Vents and Carburetor Vapor Vents … E-118 Fuel Tank Vents and Carburetor Vapor Vents … E-119 Fuel Tank Vents and Carburetor Vapor Vents … E-119 Fuel Tank Outlet … E-120 Pressure Refueling and Fueling Provisions Below Fuel Level … E-121
Page
Page No.
SUBPART E - POWERPLANT (continued)
FUEL SYSTEM COMPONENTS
AC 29.991 Fuel Pumps … E-123 AC 29.991A Fuel Pumps … E-124 AC 29.993 Fuel System Lines and Fittings … E-124 AC 29.995 Fuel Valves … E-125 AC 29.997 Fuel Strainer or Filter … E-125 AC 29.997A Fuel Strainer or Filter … E-126 AC 29.997B Fuel Strainer or Filter … E-127.1 AC 29.999 Fuel System Drains … E-127.2 AC 29.999A Fuel System Drains … E-127.2 AC 29.1001 Fuel Jettisoning … E-128
OIL SYSTEM
AC 29.1011 Oil System - General … E-130
AC 29.1019B Oil Strainer or Filter … E-134.1 AC 29.1021 Oil System Drains … E-134.2
AC 29.1025 Oil Valves … E-134.2
AC 29.1013 Oil Tanks … E-131 AC 29.1015 Oil Tank Tests … E-131 AC 29.1017 Oil Lines and Fittings … E-132 AC 29.1019 Oil Strainer or Filter … E-132 AC 29.1019A Oil Strainer or Filter … E-133
AC 29.1023 Oil Radiators … E-134
AC 29.1027 Transmission and Gearboxes: General … E-135
COOLING
AC 29.1041 Cooling - General … E-137 AC 29.1043 Cooling Tests … E-140 AC 29.1043A Cooling Tests … E-142 AC 29.1045 Cooling Test Procedures … E-143 AC 29.1047 Takeoff Cooling Test Procedures … E-147 AC 29.1049 Hovering Cooling Test Procedures … E-149
INDUCTION SYSTEM
AC 29.1091 Air Induction … E-151 AC 29.1093 Induction System Icing Protection … E-152 AC 29.1093A Induction System Icing Protection … E-160.2 AC 29.1101 Carburetor Air Preheater Design … E-161 AC 29.1103 Induction System Ducts and Air Duct Systems … E-161 AC 29.1105 Induction System Screens … E-164
Page
Page No.
SUBPART E - POWERPLANT (continued)
INDUCTION SYSTEM (continued)
AC 29.1107 Intercoolers and After-Coolers … E-165 AC 29.1109 Carburetor Air Cooling … E-165
EXHAUST SYSTEM
AC 29.1121 General … E-166 AC 29.1123 Exhaust Piping … E-167 AC 29.1125 Exhaust Heat Exchangers … E-169
POWERPLANT CONTROLS AND ACCESSORIES
AC 29.1141 Powerplant Controls: General … E-173 AC 29.1142 Auxiliary Power Unit Controls … E-174 AC 29.1143 Engine Controls … E-175 AC 29.1143A Engine Controls … E-176 AC 29.1143B Engine Controls … E-176 AC 29.1145 Ignition Switches … E-176 AC 29.1147 Mixture Controls … E-177 AC 29.1151 Rotor Brake Controls … E-178 AC 29.1157 Carburetor Air Temperature Controls … E-179 AC 29.1159 Supercharger Controls … E-179 AC 29.1163 Powerplant Accessories … E-180 AC 29.1165 Engine Ignition Systems … E-181
POWERPLANT FIRE PROTECTION
AC 29.1181 Designated Fire Zones: Regions Included … E-182 AC 29.1183 Lines, Fittings, and Components … E-183 AC 29.1185 Flammable Fluids … E-184 AC 29.1187 Drainage and Ventilation of Fire Zones … E-186 AC 29.1189 Shutoff Means … E-186 AC 29.1191 Firewalls … E-187 AC 29.1193 Cowling and Engine Compartment Covering … E-191 AC 29.1193A Cowling and Engine Compartment Covering … E-192 AC 29.1194 Other Surfaces … E-193 AC 29.1195 Fire Extinguishing Systems … E-194 AC 29.1197 Fire Extinguishing Agents … E-197 AC 29.1199 Extinguishing Agent Containers … E-200 AC 29.1201 Fire Extinguishing System Materials … E-201 AC 29.1203 Fire Detector Systems … E-201
Page xiii
Page No.
SUBPART F - EQUIPMENT
GENERAL
AC 29.1301 Function and Installation … F-1
AC 29.1305D Powerplant Instruments … F-12.1 AC 29.1307 Miscellaneous Equipment … F-12.3
AC 29.1303 Flight and Navigation Instruments … F-1 AC 29.1305 Powerplant Instruments … F-7 AC 29.1305A Powerplant Instruments … F-8 AC 29.1305B Powerplant Instruments … F-9 AC 29.1305C Powerplant Instruments … F-12
AC 29.1309 Equipment, Systems, and Installations … F-13 AC 29.1309A Equipment, systems, and Installations … F-40 AC 29.1309B Equipment, systems, and Installations … F-40.1 AC 29.1316 Electrical and Electronic System Lightning Protection … F-41 AC 29.1317 High-Intensity Radiated Fields (HIRF) Protection … F-42
INSTRUMENTS - INSTALLATION
AC 29.1321 Arrangement and Visibility … F-43 AC 29.1322 Warning, Caution, and Advisory Lights … F-44.2
AC 29.1329A Automatic Pilot System … F-60.1 AC 29.1329B Automatic Pilot and Flight Guidance System … F-60.2a
AC 29.1331 Instruments Using a Power Supply … F-60.3
AC 29.1333A Instrument Systems … F-61.1
AC 29.1335A Flight Director Systems … F-63.1 AC 29.1337 Powerplant Instruments - Fuel Gauge Calibration … F-63.2
AC 29.1323 Airspeed Indicating System … F-48 AC 29.1323A Airspeed Indicating System … F-49 AC 29.1325 Static Pressure Systems … F-50 AC 29.1327 Magnetic Direction Indicator … F-51 AC 29.1329 Automatic Pilot Systems … F-51
AC 29.1333 Instrument Systems … F-61
AC 29.1335 Flight Director Systems … F-62
AC 29.1337A Powerplant Instruments … F-64
ELECTRICAL SYSTEMS AND EQUIPMENT
AC 29.1351 Electrical Systems and Equipment - General … F-66
AC 29.1353A Energy Storage Systems … F-78.1
AC 29.1359 Electrical System Fire and Smoke Protection … F-82.1
AC 29.1353 Electrical Equipment and Installations … F-74
AC 29.1355 Distribution System … F-79 AC 29.1355A Distribution System … F-79 AC 29.1357 Circuit Protective Devices … F-80 AC 29.1357A Circuit Protective Devices … F-82
AC 29.1363 Electrical Systems Tests … F-83
Page xiv
AC 29-2C, Chg 5
Page No. SUBPART F - EQUIPMENT (continued)
LIGHTS
AC 29.1381 Instrument Lights … F-84 AC 29.1383 Landing Lights … F-85 AC 29.1385 Position Light System Installation … F-85 AC 29.1387 Position Light System Dihedral Angles … F-85 AC 29.1389 Position Light Distribution and Intensities … F-85 AC 29.1391 Minimum Intensities in the Horizontal Plane of Forward and Rear
Position Light … F-85 AC 29.1393 Minimum Intensities in Any Vertical Plane of Forward and Rear
Position Lights … F-85 AC 29.1395 Maximum Intensities In Overlapping Beams of Forward and Rear
Position Lights … F-85 AC 29.1397 Color Specifications … F-85 AC 29.1399 Riding Light … F-86 AC 29.1401 Anticollision Light System … F-87
SAFETY EQUIPMENT
AC 29.1411 Safety Equipment - General … F-88 AC 29.1413 Safety Belts: Passenger Warning Device … F-90 AC 29.1415 Ditching Equipment … F-91 AC 29.1419 Ice Protection … F-93
MISCELLANEOUS EQUIPMENT
AC 29.1431 Electronic Equipment … F-114 AC 29.1433 Vacuum Systems … F-114 AC 29.1435 Hydraulic Systems … F-115 AC 29.1439 Protective Breathing Equipment … F-118 AC 29.1457 Cockpit Voice Recorder … F-119 AC 29.1459 Flight Recorders … F-120 AC 29.1461 Equipment Containing High Energy Rotors … F-123
SUBPART G - OPERATING LIMITATIONS AND INFORMATION
AC 29.1501 Operating Limitations - General … G-1
OPERATING LIMITATIONS
AC 29.1503 Airspeed Limitations: General … G-1 AC 29.1505 Never-Exceed Speed … G-3
Page
Page No.
SUBPART G - OPERATING LIMITATIONS AND INFORMATION (continued)
OPERATING LIMITATIONS (continued)
AC 29.1509 Rotor Speed … G-6
AC 29.1517A Limiting Height-Velocity Envelope … G-9.1 AC 29.1519 Weight and Center of Gravity … G-9.2 AC 29.1521 Powerplant Limitations … G-9.2
AC 29.1517 Limiting Height-Speed Envelope … G-8
AC 29.1521A Powerplant Limitations … G-10 AC 29.1521B Powerplant Limitations … G-11 AC 29.1522 Auxiliary Power Unit Limitations … G-12 AC 29.1523 Minimum Flightcrew … G-12 AC 29.1525 Kinds of Operations … G-16 AC 29.1527 Maximum Operating Altitude … G-17 AC 29.1529 Instructions for Continued Airworthiness (Maintenance Manual) … G-17 AC 29.1529A Instructions for Continued Airworthiness (Maintenance Manual) … G-22
MARKINGS AND PLACARDS
AC 29.1541 Marking and Placards - General … G-23
AC 29.1545 Airspeed Indicator … G-27.6 AC 29.1545A Airspeed Indicator … G-27.7 AC 29.1547 Magnetic Direction Indicator … G-27.9 AC 29.1549 Powerplant Instruments … G-27.9 AC 29.1549A Powerplant Instruments … G-27.9
AC 29.1543 Instrument Markings: General … G-23 AC 29.1543A Instrument Markings: General … G-27.1
AC 29.1549B Powerplant Instruments … G-27.10 AC 29.1551 Oil Quantity Indicators … G-28 AC 29.1553 Fuel Quantity Indicator … G-28 AC 29.1555 Control Markings … G-29 AC 29.1555A Control Markings … G-29.2 AC 29.1557 Miscellaneous Markings and Placards … G-30 AC 29.1559 Limitations Placard … G-31 AC 29.1561 Safety Equipment … G-32 AC 29.1565 Tail Rotor … G-33
ROTORCRAFT FLIGHT MANUAL
AC 29.1581 Rotorcraft Flight Manual - General … G-34 AC 29.1583 Operating Limitations … G-42 AC 29.1583A Operating Limitations … G-45 AC 29.1585 Operating Procedures … G-45 AC 29.1587 Performance Information … G-47 AC 29.1587A Performance Information … G-51 AC 29.1587B Performance Information … G-51
AC 29.1589 Loading Information AC 29.1587C Performance Information … G-54.1
… G-51
Page
Page No.
CHAPTER 3 - MISCELLANEOUS GUIDANCE (MG),
TRANSPORT CATEGORY ROTORCRAFT
AC 29 MG 1 Certification Procedure for Rotorcraft Avionics Equipment … MG 1-1
System Tests
Interior Arrangements, and Equipment
Flotation System
Rotorcraft Metallic Structure (Including Flaw Tolerance)
Air Conditioning Systems
Systems (HUMS)
Systems (NVIS) Equipment
System AC 29 MG 18 Helicopter Terrain Awareness and Warning System (HTAWS) … MG 18-1
Installations
Assessment (FHA)
Installation in Part 29 Rotorcraft
AC 29 MG 2 Standardized Test Procedure for Rotorcraft DC Electrical … MG 2-1
AC 29 MG 3 Rotorcraft and Systems Certification for Category II Operations .... MG 3-1 AC 29 MG 4 Full Authority Digital Electronic Controls (FADEC) … MG 4-1 AC 29 MG 5 Agricultural Dispensing Equipment Installation … MG 5-1 AC 29 MG 6 Emergency Medical Service (EMS) Systems, Installations, … MG 6-1
AC 29 MG 7 Structural Condition Indicators … MG 7-1 AC 29 MG 8 Substantiation of Composite Rotorcraft Structure … MG 8-1 AC 29 MG 9 Rotorcraft One-Engine-Inoperative (OEI) Power Assurance … MG 9-1 AC 29 MG 10 Advisory Material for Substantiation of Emergency … MG 10-1
AC 29 MG 11 Fatigue Tolerance Evaluation of Transport Category … MG 11-1
AC 29 MG 12 External Loads … MG 12-1 AC 29 MG 13 Systems Certification Considerations … MG 13-1 AC 29 MG 14 Certification Procedure for Installation of Vapor Cycle … MG 14-1
AC 29 MG 15 Airworthiness Approval of Rotorcraft Health Usage Monitoring … MG 15-1
AC 29 MG 16 Certification Procedure for Rotorcraft Night Vision Imaging … MG 16-1
AC 29 MG 17 Guidance on Analyzing an Advanced Flight Controls (AdFC) … MG 17-1
AC 29 MG 19 Guidance on Electronic Display Systems (EDS) for Rotorcraft … MG 19-1
AC 29 MG 20 Human Factors (HF) … MG 20-1 AC 29 MG 21 Guidance on Creating a System Level Functional Hazard … MG 21-1
AC 29 MG 22 Rotorcraft One Engine Inoperative (OEI) Training Mode … MG 22-1 AC 29 MG 23 Automatic Flight Guidance and Control Systems (AFGCS) … MG 23-1
Page xvii
APPENDICES
AC 29 Appendix A – Instructions for Continued Airworthiness … Apdx A-1 AC 29 Appendix B - Airworthiness Guidance for Rotorcraft Instrument Flight … Apdx B-1 AC 29 Appendix C - (reserved) (Icing Certification) … Apdx C-1 AC 29 Appendix D - (reserved) (Criteria for Demonstration of Emergency ) … Apdx D-1
Evacuation Procedures Under § 29.803
Page xviii
FIGURES
The first digits in the figure number are the same as the related paragraph number. The digits after the hyphen are the number within the paragraph. Most figures are located at the end of the related paragraph.
Figure No. Title Page No.
AC 29.45-1 H-V Requirements. B-22
AC 29.45-2 IGE Controllability Requirements. B-23
AC 29.45-3 Shaft Horsepower vs. Turbine Outlet Temperature - B-24 Sea Level Standard Day.
AC 29.45-4 Uninstalled Takeoff Power Available. B-25
AC 29.45-5 Installed Takeoff Power Available, Anti-Ice Off, 400 RPM. B-26
AC 29.45-6 Power Assurance Check Chart. B-26.1
AC 29.53-1 Takeoff Performance Category A. B-33
AC 29.53A-1 Takeoff Performance Category A. B-35
AC 29.59-1 Category A Vertical Takeoff Profile Ground Level Heliport. B-44
AC 29.59-2 Category A Vertical Takeoff Profile Pinnacle. B-45
AC 29.59A-1 Category A Vertical Takeoff Profile Ground Level Heliport. B-55
AC 29.59A-2 Category A Vertical Takeoff Profile Elevated Heliport. B-56
AC 29.63-1 Conventional Takeoff Profile Category B. B-59
AC 29.71-1 Autorotational Characteristics – Typical. B-68
AC 29.75-1 Category A Conventional Landing - Clear Heliport. B-78
AC 29.75-2 Category A Vertical Landing. B-79
AC 29.75A-1 Category A Conventional Landing - Clear Heliport. B-89
AC 29.75A-2 Category A Vertical Landing. B-90
AC 29.79-1 Height-Velocity (HV) Diagram. B-98
AC 29.79-2 Altitude/Weight Accountability. B-99
AC 29.175-1 Static Longitudinal Stability. B-115
AC 29.175A-1 Static Longitudinal Stability. B-116.3
AC 29.251-1 Demonstration Points. B-127
AC 29.337-1 Load Factor Gross Weight Curve. C-7
AC 29.351-1 Sample Yaw/Forward Speed Diagram. C-12
Page xix
Figure No. Title Page No.
AC 29.351A-1 Sample Yaw/Forward Speed Diagram. C-14
AC 29.351B-1 Yaw/Forward Speed Diagram. C-17
AC 29.351B-2 Safety Factors for Probability of Failure. C-18
AC 29.427-1 (View Looking Forward). C-31
AC 29.427-2 (View Looking Forward). C-32
at Floor Level.
Anthropomorphic Dummy.
Bottom Cushion.
in this guidance.
AC 29.562-1 Seat Restraint System Dynamic Tests. C-58
AC 29.562-2 Schematic Floor Deformation Fixture; Seat Legs Attached C-65
AC 29.562-3 Schematic Test Fixture; Side Wall Mounted Seat. C-69
AC 29.562-4 Installation of Pelvic Lumbar Spine Load Cell in Part 572B C-73
AC 29.562-5 Measurement to be Taken Over Full Width of Seat C-85
AC 29.562-6 Post Test Condition. C-85
AC 29.562-7 Impulse Shape. C-91
AC 29.562-8 Change in Velocity. C-91
AC 29.571-1 Comparison Percent of Time in Level Flight. C-96
AC 29.571B-1 Seven Fatigue Evaluation Methods discussed C-103
AC 29.571B-2 No Growth. C-118
AC 29.571B-3 Slow Growth of Undetectable Crack. C-118
AC 29.571B-4 Slow Growth of Detectable Crack. C-119
AC 29.571B-5 Decreasing Residual Life in Secondary Load Path C-122 for Multiple Element Crack Growth with Inspections.
AC 29.571B-6 Multiple Load Path Structure Analytical Evaluation To C-123 Support Inspection for a Failed Load Path.
AC 29.571B-7 Multiple Load Path Structure Evaluation by Test to C-125 Support Inspection for a Failed Load Path.
AC 29.571B-8 Multiple Load Path Structure Analytical Evaluation to C-126 Support Inspection for Less than a Failed Load Path.
Page xx
Figure No. Title Page No.
AC 29.573-1 Schematic Diagram of Building Block Tests. C-144
AC 29.573-2 Characterization of Impact Damage. C-150
AC 29.573-3 Residual Strength vs. Time. C-154
AC 29.573-4 Illustration of Residual Strength and Damage Size. C-155 Relationships for Fail-Safe Substantiation.
AC 29.621-1 Example of Casting Load Sheet Retract Actuator D-24 Support-Landing Gear.
Certifiable Under § 29.865.
Combination vs. Applicable Cargo Type Data And Definition Summary.
AC 29.903C -4 Blade Fragment Definition.
AC 29.621-2 Castings to be Static Tested for Model XYZ. D-26
AC 29.773-1 Cockpit Visibility. D-73
AC 29.801-1 Sea State Code - World Meteorological Organization. D-96
AC 29.863-1 Flammable Fluids Fire Protection Flow Chart. D-128
AC 29.865-1 Summary of Part 133 Rotorcraft Load Combinations D-136
AC 29.865B-1 U.S. Operational (Part 133) Rotorcraft-Load D-146
AC 29.877-1 Continuous Icing-Temperature vs. Altitude Limits. D-181
AC 29.877-2 Intermittent Icing-Temperature vs. Altitude Limits. D-182
AC 29.877-3 Mean Effective Drop Diameter-Microns. D-183
AC 29.877-4 Intermittent Icing-Liquid Water Content vs. Drop Diameter. D-184
AC 29.877-5 Supercooled Clouds. D-185
AC 29.903C-1 Estimated Path of Fragments. E-23
AC 29.903C -2 Single One-Third Disc Fragment. E-24
AC 29.903C -3 Intermediate and Small Pieces of Debris. E-25
E-26
AC 29.903C -5 Distribution of Translational and Rotational Kinetic. E-27 Energy of Rotor-Component Fragments as a Function of Fragment Size.
AC 29.903C -6 Cross Section through Aircraft at Plane of Rotation of E-28 the Engine Disk Fragment.
AC 29.923A-1 Rotor Drive System Endurance. E-48
Page xxi
Figure No. Title Page No.
AC 29.923A-2 Takeoff Run Portion of Rotor Drive System Endurance … E-49
Test If 2 ½ Minute OEI Rating is Requested.
AC 29.923A-3 Takeoff Run Portion of Rotor Drive System Endurance … E-50
Test If 30 Second/2 Minute OEI Rating is Requested.
AC 29.931-1 Cantilevered Shaft, First Critical Speed … E-62
AC 29.931-2 Shaft Between Support Bearings, First Critical Speed … E-62
AC 29.952-1 Static Tension and Shear Loading Modes … E-87
AC 29.952-2 Hose Assembly Tests … E-88
AC 29.952-3 Minimum Average and Individual Loads for Hose and … E-89
Hose-End Fitting Combinations.
AC 29.952-4 Typical Method of Breakaway Fuel Fitting Load Calculations.E-90
AC 29.952-5 Typical Methods of Frangible or Deformable Attachment … E-91
Load Calculations (Frangible Bolts).
AC 29.952-6 Typical Methods of Frangible or Deformable Attachment … E-92
Load Calculations (Frangible Baffle).
AC 29.955A-1 Fuel Flow. E-102
AC 29.1041-1 Additional Cooling Test Point … E-139
AC 29.1045-1 All-Engine-Critical Altitude Additional Cooling Test Point … E-146
AC 29.1191-1 Table of Materials and Gages Acceptable for Fireproof … E-190
Protective Devices with Flat Surface Geometries.
AC 29.1309-1 Relationship Between Probability and Severity of Failure … F-17 / F-40.5
Condition Effects.
AC 29.1309-2 Failure Condition Categories and Probability Definitions … F-18 / F-40.6
AC 29.1309-3 Failure Condition Conversion … F-19
AC 29.1309-4 Safety Assessment Process Overview … F-24 / F-40.10
AC 29.1309-5 Depth of Analysis Flowchart … F-25 / F-40.11
AC 29.1321-1 Primary Fields of View … F-43
AC 29.1321-1 Secondary Fields of View … F-44
AC 29.1329-1 Height Loss Method … F-54
AC 29.1329-2 Deviation Profile … F-58
AC 29.1329-3 Deviation Profile … F-60
AC 29.1419-1 Continuous Icing-Temperature vs. Altitude Limits … F-110
Page xxii
Figure No. Title Page No.
AC 29.1419-2 Intermittent Icing-Temperature vs. Altitude Limits … F-111
Dispensing Equipment Design.
Fail-Safe Substantiation.
AC 29 MG 11-1 Crack Growth for Single Element Structure … MG 11-14
AC 29 MG 11-2 Crack Growth for Remaining Elements of Multiple … MG 11-16
Element Structure.
AC 29 MG 11-3 No Crack Growth Scenario … MG 11-18
AC 29 MG 11-4 Slow Crack Growth Scenario … MG 11-18
AC 29 MG 11-5 Detectable Crack Growth Scenario … MG 11-19
Reduction of Software Level.
with a Ground Base that uses COTS Software for Operational Software
AC 29.1419-3 Continuous Icing-Liquid Water Content vs Drop Diameter … F-112 AC 29.1419-4 Intermittent Icing-Liquid Water Content vs Drop Diameter … F-113
AC 29.MG 3-1 Category II Approach Evaluation … MG 3-5
AC 29.MG 3-2 Category II Approach Evaluation. (cont.) … MG 3-6
AC 29.MG 5-1 Acceptable Ultimate Load Factor for Agricultural … MG 5-3
AC 29.MG 5-2 Sketch of Tank Pressure Test … MG 5-7
AC 29.MG 6-1 Typical Liquid Oxygen System … MG 6-22
AC 29.MG 6-2 Typical Liquid Oxygen System - Using Combination Valve … MG 6-23
AC 29 MG 8-1 Schematic Diagram of Building Block Tests … MG 8-16
AC 29 MG 8-2 Characterization of Impact Damage … MG 8-20
AC 29 MG 8-3 Residual Strength vs. Time … MG 8-23
AC 29 MG 8-4 Residual Strength and Damage Size Relationships for … MG 8-24
AC 29 MG 9-1 Installed Engine Fuel Flow Capacity Check … MG 9-8
AC 29 MG 14-1 Refrigeration Cycle … MG 14-7
AC 29 MG 15-1 Flow Chart for Use of Mitigating Actions Applied for … MG 15-8
AC 29 MG 15-2 Flow Chart for Application of HUMS Specific Software … MG 15-11
AC 29 MG 17-1 Verification Methodology … MG 17-4
AC 29 MG 19-1 Primary Field of View … MG 19-15
AC 29 MG 19-2 Secondary Field of View … MG 29-16
AC 29 MG 20-1 Primary and Secondary Horizontal Fields of View … MG 20-18
Page xxiii
AC 29 MG 20-2 Primary and Secondary Vertical Field of View … MG 20-19
AC 29 MG 20-3 Sample HF Compliance Matrix … MG 20-27
AC 29 MG 21-1 Generic Examples by ATA … MG 21-5
AC 29.APX B-1 Rotorcraft Dynamic Stability Requirements for IFR … Apdx B-27
Page xxiv
Acronyms
AC advisory circular ACO aircraft certification office ADF automatic direction finding ADI attitude direction indicator AEH airborne electronic hardware AEO all engines operating AdFC advanced flight control AFCS automatic flight control systems AFGCS automatic flight guidance and
control systems AGL above ground level AHRS attitude heading reference system Amdt. Amendment APU auxiliary power unit ATC air traffic control BIM blade inspection method CAM cockpit area microphone CAR Civil Air Regulations CAS calibrated air speed CBIM cockpit blade inspection method CDP critical decision point CFR Code of Federal Regulations CG center of gravity COTS commercial off-the-shelf CPS cycles per second CRFS crash resistant fuel system CRI certification review item CRT cathode ray tube CVR cockpit voice recorder DER designated engineering representative DME distance measuring equipment EASA European Aviation Safety Agency ECAS engine caution advisory systems ECU environmental control unit EDS electronic data system
EFIS electronic flight instrument System[Replaced by EDS.] EFP engine failure point EHE exhaust heat exchanger ELOS equivalent level of safety ELT emergency locator transmitter EMC electromagnetic compatibility EMI electromagnetic interference EMS emergency medical service EOL end of life EUROCAE European Organization for
EVS FAA
FADEC
FAR
FEM FHA FMEA
FPM FPS FTA GPS GW HEC HF HIRF HRD HUMS
HV IAS ICA
ICAO
ICS IFR
Civil Aviation Equipment enhanced vision system Federal Aviation Administration full authority digital engine control Federal Aviation Regulations [OBSOLETE term.] finite element modeling functional hazard assessment failure mode and effects analysis feet per minute feet per second fault tree analysis global positioning system gross weight human external cargo high frequency high intensity radiated fields high rate of discharge health and usage monitoring systems height-velocity indicated airspeed instructions for continued airworthiness International Civil Aviation Organization inter-communication system instrument flight rules
Page xxv
PCDS personnel carrying device IGE in ground effect Systems IIDS integrated instrument display system ILS instrument landing system IMC instrument meteorological conditions
PCF PIO PSA PSIG
post crash fire pilot induced oscillation preliminary safety assessment pounds per square inch INS inertial navigation system gauge ISA international standard QPL qualified parts list atmosphere RFM rotorcraft flight manual ISIS integral spar inspection system ITT inter-turbine temperature
RFMS rotorcraft flight manual supplement KCAS knots calibrated airspeed RGL Regulatory and Guidance KIAS knots indicated air speed Library KTAS knots true airspeed LDP landing decision point
RPM RTCA
revolutions per minute Radio Technical Commission LPV localizer performance with Of Aeronautics vertical guidance LRU line replaceable unit LWC liquid water content MC maximum continuous MCP maximum continuous power MEL minimum equipment list MG miscellaneous guidance MGB main gearbox MGT measured gas temperature MGW maximum gross weight MMEL master minimum equipment list MSL mean sea level MVD median volume diameter NASA National Aeronautics and Space Administration NDI non-destructive inspection NM nautical mile NPRM notice of proposed rulemaking NTSB National Transportation Safety Board NVG night vision goggles NVIS night vision imaging systems OAT outside air temperature OEI one engine inoperative OGE out of ground effect
RVR SAE
SAR SAS SCAS
SHP S/N SRM SSA STC STOL TBO TC TCDS TDP TIA TIR TOP TOT TSO TVP VBIM VFR VMC
runway visual range Society of Automotive Engineers search and rescue stability augmentation system stability and control augmentation systems shaft horsepower stress vs. number of cycles structural repair manual system safety assessment supplemental type certificate short takeoff and landing time between overhaul type certificate type certificate data sheet takeoff decision point type inspection authorization type inspection report takeoff power turbine outlet temperature technical standard order true vapor pressure visual blade inspection method visual flight rules visual meteorological PBA pitch bias actuator conditions
Page xxvi
CHAPTER 1 PART 21 FAR 21 - GENERAL CERTIFICATION PROCEDURES FOR… › 21.16 SPECIAL CONDITIONS
9/30/99 AC 29-2C
CHAPTER 1. PART 21
FAR 21 - GENERAL
CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS
(Amendment 21-50)
AC 21.16. § 21.16 SPECIAL CONDITIONS.
a. The Process. Chapter 2, Section 1, Paragraph 8 of the Type Certificate Handbook, Order 8110.4A, provides detailed guidance on the special conditions process. However, much of that material has been outdated with the implementation of the Aircraft Certification Directorate Program. Rotorcraft special conditions are processed through the Rotorcraft Standards Staff, ASW-110. That office will assure coordination with the affected agency and industry elements including the Assistant Chief Counsel. All comments will be considered and the disposition will be documented by the Rotorcraft Standards Staff. ASW-100 will issue the special conditions.
b. Basis for Development.
(1) Special conditions are justified on the basis of the existing Part 29 being inadequate or inappropriate due to novel or unusual design features of the rotorcraft to be certificated.
(2) The phrase “novel or unusual” as used in § 21.16 is a very relative term. As used hereafter in applying § 21.16 to justify the issuance of special conditions, “novel or unusual” will be taken with respect to the state of technology envisaged by the applicable airworthiness standards of this subchapter. It must be recognized that in some areas which will vary from time to time, the state of the regulations may somewhat lag the state of the art in new design because of the rapidity in which the state of the art is advancing in civil aeronautical design and because of the time required to develop the experience base needed by the FAA/AUTHORITY to proceed with general rulemaking. Applicants for type certification of a new design have the opportunity to mitigate the impact of not knowing the precise airworthiness standards to be applied for “novel or unusual design features” by consulting with the FAA/AUTHORITY early in their certification planning when such features are suspected or known by the applicant to exist. It should also be recognized that, because of the intentional objective nature of the airworthiness standards of this subchapter, many new design features which might be thought of as “novel or unusual” may already be adequately covered by existing regulations, thus obviating the need to issue special conditions.
(3) Before proposing special conditions, the certification staff should very thoroughly analyze the existing regulations and assure they are inadequate or inappropriate in light of a new and novel design feature.
Page FAR 21 - 1
AC 29-2C 9/30/99
AC 21.31 § 21.31 TYPE DESIGN. The regulatory basis for requiring data to define the design is contained in § 21.31. This section is self-explanatory and broad enough in scope to give the certification staff access to sufficient data to determine compliance with Part 29.
CHAPTER 1 PART 21 FAR 21 - GENERAL CERTIFICATION PROCEDURES FOR… › 21.35 (Amendment 21-59) FLIGHT TESTS
AC 21.33 § 21.33 INSPECTION AND TESTS.
a. Applicant Responsibility. Section 21.33 requires the applicant to:
(1) Assure the test rotorcraft conforms to the type design. This must be accomplished prior to presentation to the FAA/AUTHORITY for testing.
(2) Conduct all inspections and tests necessary to determine compliance with the airworthiness and noise requirements.
b. FAA/AUTHORITY Responsibility.
(1) The design evaluation engineers should assure that the type design is adequate in their technical area and that the inspections and tests to be conducted are appropriate and sufficient to show compliance with Part 29.
(2) As changes to the rotorcraft are made during the test program, the flight test crew should assure that the appropriate design evaluation engineer concurs with the change and the conformity inspection of the change has been conducted.
AC 21.35 § 21.35 (Amendment 21-59) FLIGHT TESTS.
a. Explanation.
(1) This section outlines the requirements of the applicant for aircraft type certification and should be used in conjunction with FAA Order 8110.4A, Section 5. Section 21.35 requires, in part, that the applicant conduct sufficient flight tests to show compliance with the flight requirements throughout the proposed flight envelope. The results of the applicant’s flight test should be submitted to the FAA/AUTHORITY in report form for evaluation to determine what verification flight tests the FAA/AUTHORITY may elect to conduct. The report should conclude that in the applicant’s opinion the test aircraft complies with the applicable certification requirements. The FAA/AUTHORITY verification flight test should include, but not be limited to, the critical or marginal results contained in the applicant’s flight test report. The FAA/AUTHORITY’s role in the certification effort is not envisioned to be one of conducting day-to-day routine flight tests with the applicant, but only to verify his results through limited sampling. In certain tests, such as high altitude testing at a remote mountain site, there is an advantage in conducting flight tests concurrently with the applicant. Additionally, the FAA/AUTHORITY can provide technical flight test
Page FAR 21 - 2
9/30/99 AC 29-2C
assistance to the applicant in certain cases. This can be done after a cursory review and a letter of authorization is issued to the flight test crew.
(2) Preflight Test Planning. After the applicant’s flight test report is reviewed, it should be determined what FAA/AUTHORITY engineering flight tests are necessary. These tests are normally specified in the Type Inspection Authorization (TIA). At the same time the FAA/AUTHORITY must know and agree to the applicant’s proposed means of data acquisition, reduction, and expansion of the flight test data. The adequacy of the test instrumentation should be evaluated prior to official type certification tests (reference paragraph AC 21.39).
(3) Order of Testing. The Federal Aviation Regulations are so worded that the results of some flight tests have a definite bearing on the conduct of other tests. For this reason, and to minimize retesting, careful attention should be given to the order of testing. The exact order of testing will be determined only by considering the particular rotorcraft and test program involved. Tests which are particularly important in the early stages of the program are:
(i) Airspeed calibration: All tests involving airspeed depend upon the calibration.
(ii) Engine power available determination.
(iii) Engine cooling.
(4) Test Groupings.
(i) Weight and c.g.: In addition to the regulatory relationship of one test to another, efficient testing requires that consideration be given to the accomplishment of as many tests on a single flight as can be accommodated successfully.
(ii) Special Instrumentation. Similarly, consideration should be given to grouping of tests that involve special instrumentation. Examples of these are takeoff and landing tests which usually require group equipment to record horizontal distance, height, and time. Ground calibration of the airspeed indicating system can be accomplished at the same time. It is the applicant’s responsibility to provide the necessary instrumentation.
(5) Functional and Reliability Testing
(i) Section 21.35(b)(2) requires that the applicant determine that “there is reasonable assurance that the aircraft, its components, and its equipment are reliable and function properly.” Section 21.35(f)(1) requires a Function and Reliability (F&R) program of 300 hours for turbine engine powered aircraft incorporating engines of a type not previously used in a type certificated aircraft. Section 21.35(f)(2) requires a 150-hour F&R program for all other aircraft. The following reflects general practices that
Page FAR 21 - 3
AC 29-2C 9/30/99
have been used during rotorcraft certification programs. FAA/AUTHORITY have supported proposals which gave F&R test time credit for certification testing in lieu of dedicated F&R testing. In establishing such credit, the following should be considered:
(A) The point in time in which the rotorcraft reaches substantial conformity with the approved type design.
(B) The extent and complexity of the new design.
(C) For a previously certified rotorcraft, the F&R program requirement should be commensurate with the modification or change in type design and may be zero.
(ii) Historically, for major rotorcraft type certification programs, flight time credit has been limited so as to require an irreducible minimum of 50 hours of dedicated F&R flight time. For rotorcraft programs that involved new engine installations (mature engine design) or drive train/rotor system changes on previously certified aircraft (TC amendments or STC’s), flight time credit has been liberal and often resulted in very little or no dedicated F&R testing.
b. Procedures.
(1) Type Certification Flight Tests.
(i) Prior to initiating official FAA/AUTHORITY flight tests, a conformity inspection of the test aircraft must be accomplished. This is needed to assure that the test aircraft is in the proper configuration or “conforms” to the engineering drawings and documents that have been submitted to FAA/AUTHORITY, evaluated, and approved. It is absolutely essential to know the configuration being tested in any engineering flight evaluation. Conformity inspection prior to TIA flight tests assures that testing will not be wasted because of configuration uncertainties.
(ii) FAA Order 8110.4A, paragraph 67, contains a requirement that the applicant must keep the FAA/AUTHORITY advised of any configuration changes to the aircraft. The manufacturing inspector should keep the FAA/AUTHORITY flight test pilot apprised of any change which may affect safety of the test aircraft or may influence test results.
(iii) Results of the conformity inspection and the engineering flight test program must be documented. This is normally done in the Type Inspection Report (TIR). Results may be documented in any acceptable engineering format. The report should be in sufficient detail to clearly show how compliance with each appropriate section of the rules was determined.
(iv) The flight test pilot must assure that the FAA/AUTHORITY manufacturing inspector and certification engineer are aware of all configuration
Page FAR 21 - 4
9/30/99 AC 29-2C
changes found necessary as a result of FAA/AUTHORITY tests. The manufacturing inspector is responsible for assuring that all changes are incorporated into production drawings after the design data reflecting the change have been approved by the certification engineer.
(v) Additional flight test responsibilities, procedures, and requirements during the certification flight test process are contained in FAA Order 8110.4A, Section 5, Flight.
(2) Function and Reliability Tests.
(i) A comprehensive and systematic check of all aircraft components must be made to assure that they perform their intended function and are reliable.
(ii) F&R testing should be accomplished on an aircraft which conforms to the type design. Non-conformities must be documented and accepted. F&R testing should follow the type certification testing described in paragraph AC 21.35b(1) above to assure that significant changes resulting from type certification tests are incorporated on the aircraft prior to F&R tests.
(iii) All components of the rotorcraft should be periodically operated in sequences and combinations likely to occur in service. Ground inspections should be made at appropriate intervals to identify potential failure conditions; however, no special maintenance beyond that described in the aircraft maintenance manual should be allowed.
(iv) A complete record of defects and failures should be maintained along with required servicing of aircraft fluid levels. Results of this record should be consistent with inspection and servicing information provided in the aircraft maintenance manual.
(v) A certain portion of the F&R test program may focus on systems, operating conditions, or environments found particularly marginal during type certification tests.
(vi) A substantial portion of the flying should be on a single aircraft. The flying should be carried out to an intensive schedule on an aircraft that is very close to the final certification standard, operated and maintained as though it were in service. A range of representative ambient operating conditions and sites should be considered. It is acceptable for non-F&R flight testing conducted at various sites and in varying ambient conditions to be used to satisfy the F&R requirements for those conditions.
Page FAR 21 - 5
CHAPTER 1 PART 21 FAR 21 - GENERAL CERTIFICATION PROCEDURES FOR… › 21.39 (Amendment 21-59) FLIGHT TEST INSTRUMENT CALIBRATIONAND…
AC 29-2C 9/30/99
AC 21.39. § 21.39 (Amendment 21-59) FLIGHT TEST INSTRUMENT CALIBRATION
AND CORRECTION REPORT.
a. Explanation. It is the applicant’s responsibility to provide instrumentation for all parameters needed to show compliance with the airworthiness regulations.
(1) For those data which are necessary to show compliance with the regulations, a permanent record should be established. A permanent record is acceptable in either graphical or photographic form, and in some instances, a manual recording may be satisfactory.
(2) Regardless of the record form, the accuracy of the record must be established by reference to a laboratory standard traceable to the National Bureau of Standards.
(3) If multiplexing is used, the time base must be synchronized to a reference point from which the magnitude of each parameter can unquestionably be determined. Also, the sampling rate should be sufficiently frequent to assure that the maximums, minimums, and trends of magnitude of the parameter are recorded with respect to time.
b. Procedures. Prior to conducting flight tests, the FAA/AUTHORITY flight test team should review the applicant’s flight test instrumentation calibration and correction report.
(1) Normally the frequency of instrument calibration should not exceed 90 days. However, the frequency of recalibration varies with the consistency of the instrumentation under consideration. For example, cyclic and collective position is sometimes calibrated immediately before and after a flight where these parameters are used to provide critical flight data. Six months is a typical interval for recording/signal conditioning and nonstrain gage sensors, while one year is typical for strain gauged components. Also, environmental effects such as vibration, humidity, temperature, etc., should be considered when determining whether recalibration is necessary.
(2) The highest and lowest magnitude of the parameter being recorded should be considered when establishing the scale for instrumentation. Ideally, the highest magnitude throughout the flight would fall on the maximum indicating point of the recording.
Page FAR 21 - 6
9/30/99 AC 29-2C
CHAPTER 2. PART 29 AIRWORTHINESS STANDARDS TRANSPORT CATEGORY ROTORCRAFT
SUBPART A - GENERAL
AC 29.1. § 29.1 (Amendment 29-21) APPLICABILITY.
a. Explanation. This section prescribes the rotorcraft categories eligible for certification under this part. There is no minimum weight limit for certification under Part 29; however, Part 27 is applicable to rotorcraft with maximum weights of 6,000 pounds or less so that Part 29, in effect, deals with rotorcraft which have a maximum weight greater than 6,000 pounds. In Part 29, there are two categories of rotorcraft, Category A and Category B.
SUBPART A - GENERAL › 29.1 (Amendment 29-21) APPLICABILITY
(1) Category A. Category A provides the most rigid rules, requiring multiengine design with independent engines, fuel systems, and electrical systems. Category A design requires that no single failure can cause loss of more than one engine. Although there is no limit on maximum weight, Category A rotorcraft are certificated at a weight which will assure a minimum climb capability in the event of engine failure and with adequate surface area to assure a safe landing in the event an engine fails early in the takeoff run.
(2) Category B. Category B rotorcraft may be single or multiengine and may not have a maximum weight greater than 20,000 pounds. Category B rotorcraft are not required to have the capability for continued flight with an engine failed.
(i) Without Engine Isolation. For single engine rotorcraft and multiengine rotorcraft without engine isolation, the height-velocity diagram is conducted with sudden failure of all engines and the takeoff distance is measured through the clear area of the diagram to the 50-foot point with all engines operating. The landing distance is determined with all engines inoperative.
(ii) With Engine Isolation. Category B multiengine rotorcraft may be certificated with the Category A design features of Part 29. These rotorcraft meet the design requirements of Category A, but the performance requirements of Category B. Stay-up ability after an engine failure is not assured. The takeoff is conducted with all engines operating, while the height velocity diagram and landing distances are determined with the most critical engine inoperative.
(3) Dual Certification, Categories A and B. A multiengine rotorcraft may be certificated under both categories provided requirements for both categories are met. This combination will typically result in conditions (1) and (2)(ii) above with the primary differences being the gross weight allowed and the surface areas required for takeoff.
b. Procedures. None.
Page A - 1
SUBPART A - GENERAL › 29.1 (Amendment 29-39) APPLICABILITY
AC 29-2C 9/30/99
AC 29.1A. § 29.1 (Amendment 29-39) APPLICABILITY.
a. Explanation. Amendment 29-39 revised the reference in § 29.1(e) from §§ 29.79 to 29.87, which is a redesignation of the section number for the height-velocity envelope. This section prescribes the rotorcraft categories eligible for certification under this part. There is no minimum weight limit for certification under Part 29; however, Part 27 is applicable to rotorcraft with maximum weights of 6,000 pounds or less so that Part 29, in effect, deals with rotorcraft which have a maximum weight greater than 6,000 pounds. In Part 29, there are two categories of rotorcraft. Category A and Category B.
(1) Category A. Category A provides the most rigid rules, requiring multiengine design with independent engines, fuel systems, and electrical systems. Category A design requires that no single failure can cause loss of more than one engine. Although there is no limit on maximum weight, Category A rotorcraft are certificated at a weight which will assure a minimum climb capability in the event of engine failure and with adequate surface area to assure a safe landing in the event an engine fails anywhere in the flight envelope, including takeoff or landing operations.
(2) Category B. Category B rotorcraft may be single or multiengine and may not have a maximum weight greater than 20,000 pounds. Category B rotorcraft are not required to have the capability for continued flight with one engine inoperative.
(i) Without Engine Isolation. For single engine rotorcraft and multiengine rotorcraft without engine isolation, the height-velocity diagram is conducted with sudden failure of all engines and the takeoff and landing distances are measured with all engines operating.
(ii) With Engine Isolation. Category B multiengine rotorcraft may be certificated with the Category A design features of Part 29. These rotorcraft meet the design requirements of Category A but the performance requirements of Category B. Stay-up ability after an engine failure is not assured. The takeoff distance is determined with all engines operating. The landing distance, at the option of the applicant, may be determined with the critical engine inoperative or with all engines operating. The height-velocity diagram is determined following failure of the most critical engine.
(3) Dual Certification, Categories A and B. A multiengine rotorcraft may be certificated under both categories provided requirements for both categories are met. This combination will typically result in conditions (1) and (2)(ii) above with the primary differences being the gross weight allowed and the surface areas required for takeoff.
b. Procedures. The guidance material in paragraph AC 29.1 does not apply to rotorcraft certified with Amendment 29-39 or later.
Page A - 2
SUBPART A - GENERAL › 29.2 (Amendment 29-32) SPECIAL RETROACTIVE REQUIREMENTS
9/30/99 AC 29-2C
AC 29.2. § 29.2 (Amendment 29-32) SPECIAL RETROACTIVE REQUIREMENTS.
a. Explanation.
(1) Amendment 29-32 requires a combined shoulder harness and safety belt (also called a torso restraint system) at each occupant’s seat for all rotorcraft manufactured after September 16, 1992.
(2) The design features of the restraint system are mainly contained in this section rather than having to refer to other sections within Part 29 except for a general reference to the differing strength standards between earlier static strength only standards and the static and dynamic strength standards of Amendment 29-29.
(3) Combined safety belt and harness strength standards system follows:
(i) Those rotorcraft type designs certificated to static strength standards alone prior to Amendment 29-29, such as 4 g’s forward may use belt and harness systems, characterized as 1,500 pounds strength systems, provided they comply with those standards. TSO C22f and earlier restraint systems have such ratings. A combined belt and harness with a 1,500 pounds rating, which comply with the Part 29 standards for the rotorcraft type design, but are not necessarily TSO approved, may be approved as a part of the type design. Such design information for a non-TSO’d item would be included in a note on the aircraft type certificate data sheet (TCDS) or specification sheet by part number as “required equipment.” TSO C114-approved torso restraint systems, characterized as 3,000 pounds strength system, may be used provided the design features comply with this section, but no special information on the TCDS is necessary.
(ii) Those rotorcraft type designs certified to dynamic test requirements of Amendment 29-29 should use torso restraint systems approved under TSO C114 or approved under equivalent standards such as those contained in Part 29.
(4) Load Distribution and Design Requirements. Although not stated in § 29.2, a 60 percent and 40 percent load distribution between the safety belt and harness, respectively, is required in § 29.785(g). The safety belt should withstand 100 percent if the safety belt is capable of being used alone. Also, the safety belt or harness attachments to the seat or structure should include the 1.33 factor described in § 29.785(f)(2) of Amendment 29-24 for those rotorcraft with that certification criteria or should include the 1.15 factor as described in § 29.625 (and predecessor § 7.355(c)(2) CAR Part 7) standards for those rotorcraft with the earlier certification criteria. A factor is used whether test results or analysis methods are used for static substantiation of the seating systems. Refer to paragraph AC 29.785b(1)(i) (§ 29.785).
Page A - 3
(5) The companion operating rule change of Amendment 91-220, amended § 91.205 (Amendment 91-223), affecting the aircraft equipment requirements. Operating rule § 91.107(a) already requires use of the harness whenever the aircraft seat is so equipped.
b. Procedures.
(1) A TSO-approved combined safety belt and harness or torso restraint system may be used provided the installation requirements in § 29.2 are satisfied. A combined belt and harness (not necessarily TSO approved) may be approved as a part of the rotorcraft type design and so noted on the aircraft specification or TCDS.
(2) Structural analysis or static test may be used. For those rotorcraft designs that are subject to the dynamic test standards of § 29.562, the torso restraint system is required to be qualified for the particular use or installation in each rotorcraft type design. A dynamic test may be required for alternate restraint systems as well as the originally approved system. TSO C114 approval does not constitute approval for installation of a restraint system in a rotorcraft design subject to dynamic tests.
(i) Paragraph 27.562 of this AC concerns in part the dynamic test standards of Amendment 29-29.
(ii) AC 23-4 dated June 20, 1986, concerns static test procedures for small airplane seats and restraint systems. (Certain small airplanes manufactured after December 12, 1986, should have harnesses for each seat also.) A test proposal for rotorcraft installations may adopt procedures appropriate to the particular installation. The 60/40 percent distribution is sufficiently achieved when the blocks in Figure 4 of AC 23-4 are used.
(iii) The static design side load for the harness installation may be proven by test or analysis using the load distribution previously noted. For “older” designs, the side load of § 29.561(b)(3)(iii) is 2.0g, and for later designs (Amendment 29-29 and later), it is 8.0g.
Page A - 4
GENERAL › 29.21 (Amendment 29-24) PROOF OF COMPLIANCE
9/30/99 AC 29-2C
CHAPTER 2. PART 29 AIRWORTHINESS STANDARDS TRANSPORT CATEGORY ROTORCRAFT
SUBPART B - FLIGHT
GENERAL
AC 29.21. § 29.21 (Amendment 29-24) PROOF OF COMPLIANCE.
a. Explanation.
(1) This section provides a degree of latitude for the FAA/AUTHORITY test team in selecting the combination of tests or inspections required to demonstrate compliance with the regulations. Compliance must be shown for each combination of gross weight, center of gravity, altitude, temperature, airspeed, rotor RPM, etc. Engineering tests are designed to investigate the overall capabilities and characteristics of the rotorcraft throughout its operational envelope. Testing will identify operating limitations, normal and emergency procedures, and performance information to be included in the FAA/AUTHORITY-approved portion of the flight manual. The testing must also provide a means of verifying that the rotorcraft’s actual performance, structural design parameters, propulsion components, and systems operations are consistent with all certification requirements.
(2) Section 21.35 requires, in part, that the applicant show compliance with the applicable certification requirements, including flight test, prior to official FAA/AUTHORITY Type Inspection Authorization (TIA) testing. Compliance in most cases requires systematic flight testing by the applicant. After the applicant has submitted sufficient data to the FAA/AUTHORITY showing that compliance has been met, the FAA/AUTHORITY will conduct any inspections, flight, or ground tests required to verify the applicant’s test results. FAA/AUTHORITY compliance may be partially determined from tests conducted by the applicant if the configuration (conformity) of the rotorcraft can be verified. Compliance may be based on the applicant’s engineering data, and a spot check or validation through FAA/AUTHORITY flight tests. The FAA/AUTHORITY testing should obtain validation at critical combinations of proposed flight variables if compliance cannot be inferred using engineering judgment from the combinations investigated.
(3) Performance tests include minimum operating speed (hover), takeoff and landing, climb, glide, height-velocity, and power available. Certain other performance tests, such as Category A, are conducted to meet specific requirements. Detailed performance test procedures and allowable extrapolation or simulation limits are contained in the respective paragraphs in this order.
(i) Hover tests are conducted to determine various combinations of altitude, temperature, and gross weight for both in-ground-effect (IGE) and, if required,
Page B - 1
out-of-ground effect (OGE) conditions. From these data the hover ceiling may be calculated.
(ii) Takeoff and landing tests are conducted to determine the total distance to takeoff and land at various combinations of altitude, temperature, and gross weight.
(iii) Climb tests establish the variations of rate-of-climb at the best rate-of-climb or published climb airspeed(s) at various combinations of altitude, temperature, and gross weight.
(iv) Height-velocity tests are conducted to determine the boundaries of the height versus airspeed envelope within which a safe landing can be accomplished following an engine failure.
(v) Power available tests are conducted to verify or reestablish the calculated installed specification engine performance model on which published performance is based.
(4) The purpose of rotorcraft stability and control tests is to verify that the rotorcraft possesses the minimum qualitative and quantitative flying qualities and handling characteristics required by the applicable regulations. In order to assess the handling qualities, standardized test procedures must be utilized and the results analyzed by accepted methods. Section 29.21(a) allows calculation and inference which includes extrapolation and simulation, whereas § 29.21(b) requires demonstration of controllability, stability, and trim. Combinations of §§ 29.21(a) and 29.21(b) may be used to show compliance to the operating envelope limits. Test methods and equipment are described in individual paragraphs of this advisory circular.
b. Procedures.
(1) Efforts should begin early in the certification program to provide advice and assistance to the applicant to insure coverage of all certification requirements. The applicant should develop a comprehensive test plan which includes the required instrumentation.
(2) The tests and findings specified in paragraph a(3) above are required of the applicant to show basic airworthiness and probable compliance with the minimum requirements specified in the applicable regulations. After these basic findings have been submitted and revi2ewed, a Type Inspection Authorization, or equivalent, can be issued. The FAA/AUTHORITY will develop a systematic plan to spotcheck and confirm that compliance with the regulations has been shown. The test plan will consider combinations of weight, center of gravity, RPM and cover the range of altitude and temperature for which certification is requested.
Page B - 2
GENERAL › 29.25 (Amendment 29-12) WEIGHT LIMITS
9/30/99 AC 29-2C
AC 29.21A. § 29.21(Amendment 29-39) PROOF OF COMPLIANCE.
a. Explanation. Amendment 39 added § 29.83 which changes the requirements for determination of landing distance for Category B rotorcraft. This amendment requires landing distance to be determined with all engines operating within approved limits.
b. Procedures. The guidance material presented in paragraph AC 29.21 continues to apply.
AC 29.25. § 29.25 (Amendment 29-12) WEIGHT LIMITS.
a. Explanation.
(1) This section is definitive and specifies criteria for establishing maximum and minimum certificating weights. These weights may be based on those selected by the applicant, design requirements, or the limits for which compliance with all applicable flight requirements has been shown.
(2) Typical requirements that may establish the maximum and minimum weight limits include:
Maximum: Structural limits, performance requirements, stability, and controllability requirements.
Minimum: Autorotative rotor RPM, stability, and controllability requirements.
(3) Jettisonable External Cargo.
(i) Paragraph (c) was added by Amendment 29-12 to provide, in the certification standards, a basis for approving an increase in gross weight (exceed standard limits) that would be an external jettisonable load. The attachment device standards were moved from Part 133 (Amendment 133-5) to Parts 27 and 29. Section 29.865, “External load attaching means,“ now contains the standards, including design features, for the attaching devices. Cargo hoists and hooks were envisioned. Prior to these amendments, type design approvals were made under Part 133 and the policy in Review Cases Nos. 37 and 55 of FAA Order 8110.6 whenever the standard limits were exceeded.
(ii) In the preamble of Amendment 29-12 (Proposal 2-99, 41 FR 55454, December 20, 1976) the agency stated, in part, that “...§ 29.25(c) is intended to provide only a total weight standard for approving the rotorcraft structure (and propulsion systems) for operation under Part 133.” As indicated in § 29.865, fatigue substantiation of the external cargo attaching means is not required. The rotorcraft structure, rotors, transmissions, engines, etc., are subject to evaluation under § 29.571 for external cargo approval whenever the “standard” structural limitations are exceeded (Review Case Nos. 37 and 55).
Page B - 3
GENERAL › 29.25 (Amendment 29-51) WEIGHT LIMITS
(iii) Whether or not the standard limitations are exceeded, the flight characteristics evaluations/standards of § 133.41 are appropriate even for engineering approval. This Part 133 standard is also applicable for the individual operator to obtain his operating certificate. The operator may use an FAA/AUTHORITY approved RFM supplement for external load operations to prepare a rotorcraft load combination flight manual required by § 133.47.
b. Procedures.
(1) It may not be possible to demonstrate quantitatively all the flight requirements at the minimum weight because of test instrumentation requirements. The test team must be assured that the rotorcraft complies with the applicable requirements at the lowest permissible flying weight. This evaluation may be done qualitatively, with the test instrumentation removed, and with minimum crewmembers if no critical areas exist or are anticipated. Additionally, reasonable extrapolation may be warranted. However, if critical areas at minimum flying weights are apparent, extrapolation should not be permitted.
(2) Whenever a gross weight increase (§ 29.25(c)) is requested, a TIA evaluation is necessary to evaluate the new limitations and ensure that § 133.41 for typical or representative cargo shapes and weights (density) is satisfactory. All possible combinations of weights and shapes are not evaluated. The representative configurations may be noted in the RFM or RFM supplement for the operator’s information. Sections 133.41 and 133.47 must be satisfied by the individual operator for the particular case at hand. The approved RFM or RFM supplement should provide the necessary limitations and any other information about the representative cargo configurations evaluated. Section 133.41 also permits the operator to obtain approval of additional and unique cargo configurations provided the approved limitations are observed. Paragraph AC 29.1581 concerns the RFM and its contents.
(3) See paragraph AC 29.571, § 29.571, for fatigue substantiation and external cargo considerations.
(4) Refer to AC 133-1A, Rotorcraft External-Load Operations in Accordance with FAR Part 133, October 16, 1979, for further information on airworthiness and flight manual policy.
AC 29.25A. § 29.25 (Amendment 29-51) WEIGHT LIMITS.
a. Explanation.
(1) Amendment 29-51 added a new paragraph (a)(4) that requires that the operating envelope for the controllability demonstrated under § 29.143(c) be included in the limitations section of the Rotorcraft Flight Manual (RFM). The change allows, in addition to the 17-knot controllability requirements, the applicant to provide additional
Page B - 4
GENERAL › 29.27 (Amendment 29-3) CENTER OF GRAVITY LIMITS
controllability information within an applicant selected limited azimuth range if the rotorcraft is certified with nine or less passenger seats. This effectively allows increased weights within this limited range. Amendments 29-21 and 29-24 allowed for this relief and subsequent regulatory policy recognized these limitations as they are now required. In no case should those limits be established at an altitude that is not operationally suitable. In the past, the minimum operationally suitable altitude for takeoff and landing has been established as 3,000 feet density altitude.
(2) The explanation regarding the relief for presentation of hover controllability limits in AC 29.143.a.(2)(ii) (Amendment 29-24) is superseded by this change.
b. Procedures. The policy material pertaining to the procedures outlined in this section remain in effect.
AC 29.27. § 29.27 (Amendment 29-3) CENTER OF GRAVITY LIMITS.
a. Explanation.
(1) This regulation is definitive and requires that the center of gravity limits be defined. Proof of compliance with all applicable flight requirements is required within the range of established CG’s. Along with the longitudinal CG limits, the lateral CG limits should either be established or determined to be not critical.
(2) Ballast is usually carried during the flight test program to investigate the approved gross weight/center of gravity limits. Lead is the most commonly used form of ballast during rotorcraft flight testing although other types of ballast, such as water, may serve just as well. Water may have the added benefit of being jettisonable during critical flight test conditions. Care must be taken regarding the location of ballast. The strength of the supporting structures should be adequate to support such ballast during the flight loads that may be imposed during a particular test and for the ultimate inertia forces of § 29.561(b)(3). Of critical importance is the method of securing the ballast to the desired locations. To avoid any undesired in-flight movements of the ballast, a positive method of constraint is mandatory. The flight test crews should also visually verify the amount, location, and integrity of the ballast. The effects of mass moment of inertia on the flight characteristics due to the ballast locations should also be considered. The mass moment of inertia of the test rotorcraft should, to the extent possible, be the same as that expected in normal, approved loadings, especially during tests involving dynamic inputs.
b. Procedures.
(1) Center of gravity locations and limits are of prime importance to rotorcraft stability and safety of flight. The primary concern is establishment of the longitudinal center of gravity limits. Lateral center of gravity limits with respect to longitudinal center of gravity limits are also important. The design of the rotorcraft is usually such that approximate lateral symmetry exists. This lateral symmetry can be upset by lateral
Page B – 5
GENERAL › 29.29 (Amendment 29-15) EMPTY WEIGHT AND CORRESPONDINGCENTER OF GRAVITY
loadings resulting in the necessity to establish lateral center of gravity limits. There are two characteristics which may be seriously affected by loading outside the established center of gravity limits; these are stability and control. The established center of gravity limits must be such that as fuel is consumed, it is possible for the rotorcraft to remain within the established limits by acceptable loading and/or operating instructions.
(2) Structural limits may restrict the maximum forward longitudinal center of gravity limits. However, in most cases it is the maximum value established wherein adequate low speed control power exists to meet such requirements as § 29.143(c). Likewise, the maximum aft center of gravity limit may be a “structural limit,” but it usually is determined during flight test after the rotorcraft’s handling qualities tests have been conducted. Additional items which may influence the maximum aft center of gravity limits may be malfunctions of automatic stabilization equipment, excessive rotorcraft attitudes during critical phases of flight, or adequate control power to compensate for an engine failure.
(3) Lateral center of gravity limits have become more critical because of the ever increasing utilization of the rotorcraft for such things as unusual and unsymmetric lateral loads, both internal and external. Maximum allowable lateral center of gravity limits have also influenced the results of the unusable fuel determination.
(4) Summarizing, it is of prime importance that longitudinal and lateral center of gravity limits be determined so that unsafe conditions do not exist within the approved altitude, airspeed, ambient temperature, gross weight, and rotor RPM ranges. All relevant malfunctions must be considered.
AC 29.29. § 29.29 (Amendment 29-15) EMPTY WEIGHT AND CORRESPONDING CENTER OF GRAVITY.
a. Explanation. The empty weight of the rotorcraft consists of the airframe, engines, and all items of operating equipment that have fixed locations and are permanently installed (including both required and optional equipment) in the rotorcraft. It includes fixed ballast, unusable fuel, other unusable fluids, and full operating fluids. “Full operating fluids” such as oils used in an engine, auxiliary power unit, main and auxiliary gearboxes, and hydraulic systems are considered “closed fluid systems” typically filled to a “full mark” indicator level. Fluids necessary for the operation of non-permanently installed equipment (i.e., carry-on equipment) are not considered part of the empty weight.
(1) A ballast is fixed when made a permanent part of the rotorcraft as a means of controlling the certificated empty weight center of gravity (CG).
(2) Installed equipment is any FAA-approved equipment attached to the rotorcraft with hardware and, as a result, becomes an integral part of the rotorcraft. The installation or removal of such equipment must be recorded in the aircraft equipment list. Compliance with paragraph (b) of § 29.29 is accomplished by the use of an
Page B – 6
equipment list specifying the installed equipment at the time of weighing and the weight moment arm of the equipment.
b. Procedures.
(1) Determination of the empty weight and corresponding center of gravity is primarily the responsibility of the manufacturer and is normally made on a production rotorcraft rather than a prototype. If the manufacturer has been issued a production certificate and wishes to avoid weighing each production rotorcraft, the manufacturer may make a detailed proposal defining the procedure it would use to establish an empty weight and CG. When the proposal is approved, the manufacturer will weigh the first five to ten production rotorcraft and show that the rotorcraft will be within ±1 percent on empty weight and ±0.2 inches on CG. After this procedure is established, the empty weight and CG may be computed except that at regular intervals a rotorcraft will be weighed to ensure the tolerances are still being maintained (e.g., one in ten rotorcraft).
(2) For prototype and modified rotorcraft, it is only necessary to establish a known basic weight and CG position (by weighing) from which the extremes of weight and CG travel required by the test program may be calculated. See the current version of FAA-H-8083-1 (Pilots Weight and Balance Handbook) for a sample weight and balance procedure.
(3) The weight and balance should be recalculated if a modification (or series of modifications) to the rotorcraft results in a significant change to the empty weight. Additionally, this change in empty weight should be reflected with the weight and balance information contained in the rotorcraft flight manual or rotorcraft flight manual supplement.
c. Ballast Loading and Type.
(1) Ballast loading of the rotorcraft can be accomplished in any manner to achieve a specific CG location. It is acceptable for such ballast to be mounted outside the physical confines of the rotorcraft if the flight test objectives are not affected by this arrangement. In flight test work, loading problems will occasionally be encountered in which it will be difficult to obtain the desired CG limits. Such cases may require loading in engine compartments or other places not designed for load carrying. When this condition is necessary, care should be taken to ensure that local structural stresses are not exceeded or that the rotorcraft flight characteristics are not changed due to increased moments of inertia by attaching the ballast to extreme CG locations that may not be designed for the added weight.
(2) The two types of ballasts that may be used in loading are solid or liquid. The solids are usually high density materials such as lead, while the liquid usually used is water. In critical tests, the ballast may be loaded in a manner so that disposal in flight can be accomplished. In any case, the load should be securely attached in its loaded position so shifting or interference with safety of flight will not result.
Page B – 7
GENERAL › 29.33 (Amendment 29-15) MAIN ROTOR SPEED AND PITCH LIMITS
AC 29.31. § 29.31 REMOVABLE BALLAST.
a. Explanation. This regulation provides the option of using removable ballast for operational flights to obtain center of gravity locations that are in compliance with the flight requirement of this Part. Fixed ballast used for flight operations after type certification must be documented in the type design data. Removable ballast is used primarily on small rotorcraft to control the CG with different passenger loadings although this regulation does permit its use on transport rotorcraft. If removable ballast is used, the rotorcraft flight manual must include instructions regarding its use and limitations. See paragraph AC 29.873 for information on ballast provisions.
b. Procedures. None.
AC 29.33. § 29.33 (Amendment 29-15) MAIN ROTOR SPEED AND PITCH LIMITS.
a. Explanation.
(1) General. This rule requires the establishment of power-on and power-off main rotor speed limits and the requirements for low rotor speed warning.
(2) Power-On. The power-on limits should be sufficient to maintain the rotor speed within these limits during any appropriate maneuver expected to be encountered in normal operations throughout the flight envelope for which certification is requested. A power-on range of approximately 3 percent has in the past been the minimum range required due to engine governor and engine operating characteristics. With the introduction of advanced engines and electronic engine controls, there may not be a need for a range, but one fixed value may suffice. Transient power-on values may also be acceptable provided they are substantiated.
(3) Power-Off. The power-off rotor speed limits should be sufficient to encompass the rotor speeds encountered during normal autorotative maneuvers except for final landing phase (touchdown) for which rotor RPM may be lower than the minimum transient limit for flight, provided stress limits are not exceeded. The limits should also be sufficient to cover the ranges of airspeed, weight, and altitudes for which certification is requested. It is not the intent of the rule to require the minimum and maximum limit values in conjunction with extremes such as maximum/minimum weights and/or high altitude. The minimum and maximum rotor speed requirements should be thoroughly evaluated at normal operation environment; i.e., at altitudes between approximately sea level and 10,000 feet, temperatures not at extremes, and weights as necessary for other tests and as required to readily establish the limit rotor speeds. Spot checks of the autorotative requirements should be made at the extremes of the flight envelope and environmental conditions during normal tests at those conditions. Under conditions where high autorotative rotor speeds may be encountered, it is acceptable for the pilot to adjust the controls to prevent overspeeding of the rotor. At light weight combined with low altitudes and extreme cold temperatures, the normal low pitch setting may not be sufficient to maintain autorotational rotor speed values within
Continue reading ↓ 120 of 3583 passages shown