Radar Vectors
Advisory Circular Cancelled Issued Mar 31, 1998 ANM-111 459 pages Copy saved Nov 18, 2026

AC 25-7A Flight Test Guide for Certification of Transport Category Airplanes

This advisory circular (AC) provides guidance for the flight test evaluation of transport category airplanes. This AC includes flight test methods and procedures to show compliance with the regulations contained in subpart B of Title 14, Code of Federal Regulations (14 CFR) part 25, which address airplane performance and handling characteristics. Part 25 has been amended significantly since the last revision of this AC and, likewise, guidance and policy have changed in many areas as experience has been gained. During this time period, technology has advanced as well, resulting in a need for new or modified test techniques. This revision, AC 25-7B, adds acceptable means of compliance for the regulatory changes associated with amendments 108, 109, and 115 to part 25, and a revised means of compliance for expansion of takeoff and landing data for higher airport elevations. Means of compliance associated with flight in icing conditions was removed as this material is now contained in AC 25-25.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. Department

ederal Aviation

dministration Circular

of Transportation

F A

Advisory

AC 25-7A DA

TE: 3/31/98

FLIGHT TEST GUIDE

FOR CERTIFICATION OF

TRANSPORT CATEGORY AIRPLANES

Subject: FLIGHT TEST GUIDE FOR CERTIFICATION OF TRANSPORT CATEGORY AIRPLANES

Date: 6/3/99 Initiated By: ANM-110

AC No: 25-7A Change: 1 1. PURPOSE. This change provides updated guidance material to ensure consistent application of certain airworthiness requirements adopted by recent amendments to 14 CFR part 25. Changed material is indicated in the margins by asterisks and at the top of each changed page with the change number and date. New material on pages 80-1 through 80-28 is indicated by the change number and date only. Some text, although not changed, has been rearranged to accommodate new material. 2. PRINCIPAL CHANGES. a. New guidance regarding an acceptable means of compliance with the wet runway and worn brake requirements adopted by Amendment 25-92, “Improved Standards for Determining Rejected Takeoff and Landing Performance.” b. Additional guidance regarding criteria for locating the gate when the airplane has multiple go-around configurations, for compliance with the gate design requirements adopted by Amendment 25-98, “Revision of Gate Requirements for High-Lift Device Controls.”

PAGE CONTROL CHART Remove Pages Dated Insert Pages Dated iii thru x 3/31/98 iii thru x 6/3/99 71 thru 105 3/31/98 71 thru 106 6/3/99 129 thru 148 3/31/98 129 thru 149 6/3/99 283 thru 300 3/31/98 283 thru 301 6/3/99 /s/ John J. Hickey Acting Manager, Transport Airplane Directorate Aircraft Certification Service

Subject: FLIGHT TEST GUIDE FOR CERTIFICATION OF TRANSPORT CATEGORY AIRPLANES

Date: 3/31/98 Initiated By: ANM-110

AC No: 25-7A Change: 1. PURPOSE. This revised advisory circular (AC) provides updated guidance for the flight test evaluation of transport category airplanes. These guidelines provide an acceptable means of demonstrating compliance with the pertinent regulations of 14 CFR part 25. The methods and procedures described herein have evolved through many years of flight testing of transport category airplanes and, as such, represent current certification practice. Like all AC material, these guidelines are not mandatory and do not constitute regulations. They are derived from previous FAA experience in finding compliance with the airworthiness requirements and represent methods and procedures found to be acceptable by that experience. Although mandatory terms such as “shall” and “must” are used in this AC, because the AC method of compliance is not in itself mandatory, these terms apply only to applicants who seek to demonstrate compliance by use of the specific methods described in this AC. 2. CANCELLATION.

AC 25-7, “Flight Test Guide for Certification of Transport Category Airplanes,” dated April 9, 1986. 3. BACKGROUND. Since AC 25-7 was released on April 9, 1986, it has been the primary source of guidance for flight test methods and procedures to show compliance with the regulations contained in subpart B of part 25, which are related to airplane performance and handling characteristics. For certification flight testing to show compliance with other part 25 regulations, Order 8110.8, “Engineering Flight Test Guide for Transport Category Airplanes,” provided guidance for internal FAA use in determining acceptable means of compliance. Order 8110.8, as revised on September 26, 1974, has been subject to five change updates to reflect significant policy changes; the last change being the removal of the subpart B-related material concurrent with the original release of AC 25-7. Order 8110.8 reflected the policy in place when Amendment 25-29 to part 25 was adopted, and the original release of AC 25-7 reflected an Amendment 25-59 time frame.

Part 25 has been amended significantly since the two referenced documents were last revised and, likewise, guidance and policy have changed in many areas as experience has been gained. During this time period, many advances in technology have also taken place that require new or modified test techniques. This revision updates the original AC to incorporate the latest policy and guidance material applicable to all sections of part 25. The material related to regulations outside of subpart B supersedes that contained in Order 8110.8, which has been cancelled accordingly upon issuance of this AC.

4. APPLICABILITY. These methods and procedures are promulgated, in the interest of standardization, for use during all transport category airplane flight test certification activities. This material is not to be construed as having any legal status and must be treated accordingly. The procedures set forth herein are one acceptable means of compliance with applicable sections of part 25. Any alternate means proposed by the applicant should be given due consideration. Applicants are encouraged to use their technical ingenuity and resourcefulness in order to develop more efficient and less costly methods of achieving the objectives of Part 25. Since these methods and procedures are only one acceptable means of compliance, individuals should be guided by the intent of the methods provided in this AC. As deviations from the methods and procedures described in this AC may occur, FAA certification personnel will coordinate what they consider to be major deviations with the Transport Standards Staff (ANM-110) of the Transport Airplane Directorate. If in their judgment, however, a deviation is considered to be minor, coordination with ANM-110 may not be necessary. 5. RELATED PUBLICATIONS. Certification personnel should be familiar with FAA Order 8110.4A, “Type Certification Process,” and FAA Order 8100.5, “Aircraft Certification Directorate Procedures.” In this AC, reference is made to other FAA advisory circulars that provide guidance on various aspects of type certification and supplemental type certification. /s/ Ronald T. Wojnar Manager, Transport Airplane Directorate Aircraft Certification Service

ii

6/3/99 AC 25-7A Chg. 1

CONTENTS Paragraph Page No.

CHAPTER 1. GENERAL 1. FAR 25.1 Applicability [RESERVED] 1 2. FAR 25.2 Special Retroactive Requirements [RESERVED] 1

CHAPTER 2. FLIGHT

Section 1. GENERAL 3. FAR 25.21 Proof of Compliance … 31 Figure 3-1 Weight Tolerance Limits … 33 Figure 3-2 Equivalent Weight Extrapolation … 34 Figure 3-3 Test Parameters That Normally Can Be Corrected … 35 Figure 3-4 Wind Profile Variation … 36 4. FAR 25.23 Load Distribution Limits [RESERVED] … 42 5. FAR 25.25 Weight Limits [RESERVED] … 42 FAR 25.27 Center of Gravity Limits [RESERVED] … 42 6. FAR 25.29 Empty Weight and Corresponding Center of Gravity [RESERVED] … 42 7. FAR 25.31 Removable Ballast [RESERVED] … 42 8. FAR 25.33 Propeller Speed and Pitch Limits … 43

Section 2. PERFORMANCE 9. FAR 25.101 General … 71 FAR 25.103 Stalling Speed (see paragraph 29) 10. FAR 25.105 Takeoff … 71 FAR 25.107 Takeoff Speeds … 71 11. FAR 25.109 Accelerate-Stop Distance … 80 Figure 11-1 Accelerate-Stop Time Delays … 80-7 Figure 11-2 Accelerate-Stop Speed Vs. Distance … 80-9 Figure 11-3 Anti-Skid System Response Characteristics (On-Off System) … 80-13 Figure 11-4 Anti-Skid System Response Characteristics (Quasi-Modulating System) … 80-15 Figure 11-5 Anti-Skid System Response Characteristics (Fully Modulating System) … 80-17 Figure 11-6 Instantaneous Brake Force and Peak Brake Force … 80-21 Figure 11-7 Anti-Skid Efficiency-Wheel Slip Relationship … 80-23 Figure 11-8 Substantiation of the Optimal Slip Value … 80-24

iii

AC 25-7A 6/3/99 Chg. 1

12. FAR 25.111 Takeoff Path … 81 13. FAR 25.113 Takeoff Distance and Takeoff Run … 88 Figure 13-1 Takeoff Distance on a Dry Runway … 89 Figure 13-2 Takeoff Distance (All Engines Operating) … 89 Figure 13-3 Takeoff Distance on a Wet Runway … 90 Figure 13-4 Takeoff Run (Critical Engine Fails at VEF) … 91 Figure 13-5 Takeoff Run (All Engines Operating) … 91 Figure 13-6 Clearway Profiles … 92 14. FAR 25.115 Takeoff Flight Path … 92 Figure 14-1 Takeoff Segments & Nomenclature … 93 Figure 14-2 Net Takeoff Flight Path … 94 15. FAR 25.117 Climb: General..94 16. FAR 25.119 Landing Climb: All-Engines Operating … 95 17. FAR 25.121 Climb: One-Engine-Inoperative … 96 18. FAR 25.123 En route Flight Paths … 97 19. FAR 25.125 Landing … 98 Figure 19-1 Landing Time Delays … 103

Section 3. CONTROLLABILITY AND MANEUVERABILITY 20. FAR 25.143 General … 121 Figure 20-1 Sample Pitch Tracking Task … 129 Figure 20-2 A-PC Rating Criteria & Comparison to MIL Standard … 130 Figure 20-3 Example of Minimum Permitted HQ Rating for A-PC Tendencies … 131 21. FAR 25.145 Longitudinal Control … 135 22. FAR 25.147 Directional and Lateral Control … 140 23. FAR 25.149 Minimum Control Speed … 143

Section 4. TRIM 24. FAR 25.161 Trim [RESERVED] … 157

Section 5. STABILITY 25. FAR 25.171 General [RESERVED] … 171 26. FAR 25.173 Static Longitudinal Stability … 171 FAR 25.175 Demonstration of Static Longitudinal Stability … 171 Figure 26-1 Longitudinal Static Stability … 173 27. FAR 25.177 Static Directional and Lateral Stability … 173 28. FAR 25.181 Dynamic Stability … 175

iv

6/3/99 AC 25-7A Chg. 1

Section 6. STALLS 29. Stall Testing … 189 FAR 25.201 Stall Demonstration … 189 FAR 25.203 Stall Characteristics … 194 FAR 25.207 Stall Warning … 197 Figure 29-1 Stall Test Time History … 199 Figure 29-2 Stall CLCG vs. Entry Rate … 200 Figure 29-3 Stall CL vs. Weight and Flap Setting … 200 Figure 29-4 Stall Speeds vs. Weight and Flap Setting … 201 Figure 29-5 Thrust Effect on Stall CL … 201

Section 7. GROUND AND WATER HANDLING CHARACTERISTICS

30. General … 211 FAR 25.231 Longitudinal Stability and Control … 211 FAR 25.233 Directional Stability and Control … 211 FAR 25.235 Taxiing Condition [RESERVED] … 212 FAR 25.237 Wind Velocities … 212 FAR 25.239 Spray Characteristics, Control, and Stability on Water … 213

Section 8. MISCELLANEOUS FLIGHT REQUIREMENTS 31. FAR 25.251 Vibration and Buffeting … 221 Figure 31-1 Maneuvering Characteristics … 224 (Speeds up to the Lesser of VFC or MFC or Buffet Onset) Figure 31-2 Maneuvering Characteristics … 225 (Speeds between Figure 31-1 and VDF or MDF) 32. FAR 25.253 High Speed Characteristics … 225 33. FAR 25.255 Out-of-Trim Characteristics … 229 Figure 33-1 Mistrimmed Maneuvering Characteristics … 231

CHAPTER 3. STRUCTURE

[RESERVED]

CHAPTER 4. DESIGN AND CONSTRUCTION

Section 1. GENERAL [RESERVED]

Section 2. CONTROL SURFACES [RESERVED]

v

AC 25-7A 6/3/99 Chg. 1

Section 3. CONTROL SYSTEMS 34. FAR 25.671 General … 261 [35-45] [RESERVED] … 261 46. FAR 25.701 Flap and Slat Interconnections … 261 47. FAR 25.703 Takeoff Warning System [RESERVED] … 262

Section 4. LANDING GEAR [48-51] [RESERVED] … 283 52. FAR 25.729 Retracting Mechanisms … 283 53. FAR 25.731 Wheels … 284 54. FAR 25.733 Tires [RESERVED] … 286 55. FAR 25.735 Brakes … 286 56. FAR 25.737 Skis [RESERVED] … 301

Section 5. FLOATS AND HULLS [57-59] [RESERVED] … 311

Section 6. PERSONNEL AND CARGO ACCOMMODATIONS [60-61] [RESERVED] … 323 62. FAR 25.773 Pilot Compartment View … 323 [63-72] [RESERVED] … 323

Section 7. EMERGENCY PROVISIONS 73. FAR 25.801 Ditching [RESERVED] … 333 74. FAR 25.803 Emergency Evacuation … 333 [75-83] [RESERVED] … 333

Section 8. VENTILATION AND HEATING 84. FAR 25.831 Ventilation … 343 85. FAR 25.832 Cabin Ozone Concentration [RESERVED] … 343 86. FAR 25.833 Combustion Heating Systems [RESERVED] … 343

Section 9. PRESSURIZATION 87. FAR 25.841 Pressurized Cabins … 353 88. FAR 25.843 Tests for Pressurized Cabins … 355

vi

6/3/99 AC 25-7A Chg. 1

Section 10. FIRE PROTECTION [RESERVED]

Section 11. MISCELLANEOUS [RESERVED]

CHAPTER 5. POWERPLANT

Section 1. GENERAL 89. FAR 25.901 Installation [RESERVED] … 387 90. FAR 25.903 Engines … 387 FAR 25.903(b) Engine Isolation … 387 FAR 25.903(c) Control of Engine Rotation … 387 FAR 25.903(d) Turbine Engine Installations … 388 FAR 25.903(e) Engine Restart Capability … 389 91. FAR 25.904 Automatic Takeoff Thrust Control Systems (ATTCS) … 390 92. FAR 25.905 Propellers … 392 93. FAR 25.907 Propeller Vibration [RESERVED] … 392 94. FAR 25.925 Propeller Clearance [RESERVED] … 392 95. FAR 25.929 Propeller Deicing … 392 96. FAR 25.933 Reversing Systems … 393 97. FAR 25.934 Turbojet Engine Thrust Reverser Sys. Tests [RESERVED] ..396 98. FAR 25.937 Turbopropeller-Drag Limiting Systems … 396 99. FAR 25.939 Turbine Engine Operating Characteristics … 398 100. FAR 25.941 Inlet, Engine, and Exhaust Capability (RESERVED … 398 101. FAR 25.943 Negative Acceleration … 399 102. FAR 25.945 Thrust or Power Augmentation System [RESERVED] … 399

Section 2. FUEL SYSTEM [103-108] [RESERVED] … 419 109. FAR 25.959 Unusable Fuel Supply … 419 110. FAR 25.961 Fuel System Hot Weather Operation … 421 [111-116] [RESERVED] … 423 117. FAR 25.975 Fuel Tank Vents and Carburetor Vapor Vents … 423 [118-120] [RESERVED] … 424

Section 3. FUEL SYSTEM COMPONENTS [121-126] [RESERVED] … 445 127. FAR 25.1001 Fuel Jettisoning System … 445

Section 4. OIL SYSTEM [RESERVED]

vii

AC 25-7A 6/3/99 Chg. 1

Section 5. COOLING [128-130] [RESERVED] … 481

Section 6. INDUCTION SYSTEM 131. FAR 25.1091 Air Induction … 497 132. FAR 25.1093 Induction System Icing Protection … 499 [133-136] [RESERVED] … 501

Section 7. EXHAUST SYSTEM

137. FAR 25.1121 General … 511 [138-140] [RESERVED]

Section 8. POWERPLANT CONTROLS AND ACCESSORIES [141-154] [RESERVED] … 521

Section 9. POWERPLANT FIRE PROTECTION [155-158] [RESERVED] … 537 159. FAR 25.1187 Drainage and Ventilation of Fire Zones … 537 [160-164] [RESERVED] … 537 165. FAR 25.1197 Fire Extinguishing Agents … 537 [166-169] [RESERVED] … 538

CHAPTER 6. EQUIPMENT

Section 1. GENERAL 170. FAR 25.1301 Function and Installation … 559 171. FAR 25.1303 Flight and Navigation Instruments … 592 172. FAR 25.1305 Powerplant Instruments [RESERVED] … 594 173. FAR 25.1307 Miscellaneous Equipment [RESERVED] … 594 174. FAR 25.1309 Equipment, Systems, and Installations … 594

Section 2. INSTRUMENTS: INSTALLATION 175. FAR 25.1321 Arrangement and Visibility [RESERVED] … 605 176. FAR 25.1322 Warning, Caution, and Advisory Lights [RESERVED] … 605 177. FAR 25.1323 Airspeed Indicating System … 605 178. FAR 25.1325 Static Pressure Systems … 608 179. FAR 25.1326 Pitot Heat Indicator Systems [RESERVED] … 609 180. FAR 25.1327 Magnetic Direction Indicator [RESERVED] … 609

viii

6/3/99 AC 25-7A Chg. 1

181. FAR 25.1329 Automatic Pilot System … 609 Figure 181-1 Altitude Loss vs. Altitude Go-Around Mode … 617 [182-185] [RESERVED] … 625

Section 3. ELECTRICAL SYSTEMS AND EQUIPMENT 186. FAR 25.1351 General … 635 187. FAR 25.1353 Electrical Equipment and Installations … 637 188. FAR 25.1355 Distribution System … 639 189. FAR 25.1357 [RESERVED] … 639 190. FAR 25.1363 Electrical System Tests … 639

Section 4. LIGHTS 191. FAR 25.1381 Instrument Lights … 651 192. FAR 25.1383 Landing Lights … 651 193. FAR 25.1385 Position Light System Installation … 651 [194-200] [RESERVED] … 652 201. FAR 25.1401 Anticollision Light System … 652 202. FAR 25.1403 Wing Icing Detection Lights … 652

Section 5. SAFETY EQUIPMENT [203-207] [RESERVED] … 659

Section 6. MISCELLANEOUS EQUIPMENT 208. FAR 25.1431 Electronic Equipment … 669 [209-223] [RESERVED] … 669

CHAPTER 7. OPERATING LIMITATIONS & INFORMATION

Section 1. [RESERVED]

Section 2. Operating Limitations [RESERVED]

Section 3. Markings and Placards [RESERVED]

Section 4. Airplane Flight Manual 224. FAR 25.1581 General … 679 [225-227] [RESERVED] … 679

ix

AC 25-7A 6/3/99 Chg. 1

CHAPTER 8. AIRWORTHINESS-MISCELLANEOUS ITEMS 228. Design and Function of Artificial Stall Warning and Identification Systems … 701 229. Reduced and Derated Thrust Takeoff Operations … 704 230. Runway Gradients Greater than +2 Percent … 705 231. Performance Requirements for Flight in Icing Conditions … 707 232. Flying Qualities in Natural Icing Conditions … 708 233. Criteria for Approval of Steep Approach to Landing … 709 234. Takeoff and Landing on Unpaved Runways … 713 235. Accountability of Performance Degradation Relative Both Minor Design Changes (External Exposure) and Configuration Deviation List (CDL) Items … 716 236. Configuration Deviation List (CDL) … 717 237. Spare Engine Pod … 719 238. Authorization for Ferry Flight with One Engine Inoperative … 719 239. Instrument Landing System Weather Minima … 720 240. Takeoff Performance Credit for Alternate Forward Center of Gravity Limits....721 241. Performance Credit for Automatic Propeller Drag Reduction Devices … 724 242. Airplane Backing Using Reverse Thrust … 725

APPENDICES Appendix 1 History of Jet Transport Performance Standards (CAR 4b Special Regulations 422, 422A and 422B) Appendix 2 History of Accelerate-Stop Transition Time Development Appendix 3 Correction of Air Minimum Control Speed (VMCA) to Standard Conditions Appendix 4 Rudder Pedal Force-Limited Air Minimum Control Speed (VMCA) Appendix 5 One-G Stall Compliance Basis Appendix 6 Sample Flight Test Program [RESERVED Appendix 7 FAA Handling Qualities Rating System Appendix 8 Functional and Reliability Tests (§ 21.35(b)(2))

x

CHAPTER 1 - GENERAL 1.-2. [RESERVED]

1 (thru 30)

This page intentionally left blank

CHAPTER 2 - FLIGHT

Section 1. GENERAL 3. PROOF OF COMPLIANCE - § 25.21. a. Explanation. In an effort to provide the necessary guidelines for the flight test evaluation of transport category airplanes, without producing a cumbersome document, this advisory circular assumes a conventional transport airplane configuration. In general, a “conventional” airplane configuration is one with: distinct wing and fuselage elements that are joined together; aft-mounted horizontal and vertical stabilizers that are attached to the fuselage; and propulsion provided either by turbojet/turbofan engines that do not provide any significant increase in lift due to their operation or engine-driven propellers. The effects of nonconventional airplane configurations (e.g., blown flaps) on the compliance methods should be evaluated and determined based on the intent of the guidelines presented for conventional airplane configurations. (1) Section 25.21(a) - Proof of Compliance. (i) The burden of showing compliance with the flight requirements for an airworthiness certificate or a type certificate rests with the applicant.

The applicant should, at his own expense and risk, conduct such official flight tests as required by the FAA to demonstrate compliance with the applicable requirements. During the certification process, the applicant should make available the airplane, as well as all of the personnel and equipment necessary to obtain and process the required data. (ii) If the airplane flight characteristics or the required flight data are affected by weight and/or center of gravity (c.g.), the compliance data should be presented for the most critical weight and c.g. position. Unless it can be shown that the allowable c.g. travel in one or more axes (e.g., lateral fuel imbalance) has a negligible effect on the airworthiness requirements, compliance at the critical c.g. must be substantiated. (iii) The gross weight and c.g. tolerances specified in paragraphs 3a(3)(ii)(A) and (D) are test tolerances and are not intended to allow compliance to be shown at less than critical conditions. (iv) Section 25.21(a)(1) requires, in part, that the test airplane be in conformity with its type design specifications.

(A) This is interpreted as meaning the test airplane must be in conformity with its type design specification as relates to the particular test being conducted. (B) Any deviation from conformity must be clearly shown to be of no consequence to the particular test being conducted. For example, if the slip resistant escape

surface required by § 25.810(c) is not installed, it must be shown that its presence would have no effect on measured airplane performance and flight characteristics. (2) Section 25.21(c) - Proof of Compliance (Altitude Effect on Flight Characteristics). (i) Any of the flying qualities, including controllability, stability, trim, and stall characteristics, affected by altitude should be investigated for the most adverse altitude conditions approved for operations and limited, as appropriate, in accordance with § 25.1527. (ii) Consideration should be given in the test program to aerodynamic control system changes with altitude (e.g., control throws or auto slats which are sometimes inhibited by Mach number at altitude). (3) Section 25.21(d) - Proof of Compliance (Flight Test Tolerances). (i) To allow for variations from precise test values, certain tolerances during flight testing should be maintained. The purpose of these tolerances is to allow for variations in flight test values from which data are acceptable for reduction to the value desired.

They are not intended for tests to be routinely scheduled at the lower weights, or to allow for compliance to be shown at less than the critical condition; nor are they to be considered as allowable inaccuracy of measurement. As an example, when demonstrating stability with a specified trim speed of 1.4 VS1, the trim speed may be 1.4 VS1 +3 knots or 3 percent; however, no positive tolerance is permitted when demonstrating the minimum prescribed trim speed of 1.4 VS1 (Ref. § 25.161). (ii) Where variation in the parameter on which a tolerance is allowed will have an effect on the results of the test, the results should be corrected to the most critical value of that parameter within the operating envelope being approved. If such a correction is impossible or impractical (e.g., performance at forward c.g.), the average test conditions should assure that the measured characteristics represent the actual critical value. (A) Weight limits. Figure 3-1, below, presents weight tolerances that have been found acceptable for the specified flight tests.

Many flight tests need to be conducted at or very near the maximum operating weight for the airplane configuration, particularly those tests used to establish Airplane Flight Manual performance information. As noted in paragraph (i), above, the purpose of the test tolerances is to allow for variations in flight test values, not to routinely schedule tests at less than critical weight conditions or to allow for compliance to be shown at less than the critical weight condition.

FIGURE 3-1. WEIGHT TOLERANCE LIMITS

Flight Test Conditions Weight Tolerance Limit +5% +10% Stall Speeds X Stall Characteristics X Climb Performance X Takeoff Flight Paths X Landing Braking Distance X Landing Air Distance X Takeoff Distance & Speed X Accelerate-Stop Distance X Maximum Energy RTOs X Minimum Unstick Speed X (1) For follow-on airplane certification programs (e.g., minor gross weight increase), where it is desired to use an existing certificated data base from an aerodynamically similar model of the same airplane type, the test weight tolerance limits of Figure 3-1 have also been applied as extrapolation limits to minimize additional test requirements. (2) For follow-on airplane certification programs, test data may be extrapolated to higher gross weights than specified in Figure 3-1, if the available test data include an adequate range of weights and an appropriate number of points at the highest weight tested. If the test data analysis verifies the predicted effect of weight, then other extrapolation limits may apply. (3) Equivalent weight extrapolation limits.

For follow-on airplane certification programs where it is desired to increase a maximum operating weight based on existing certified performance parameters that have weight as one of their independent terms, those parameters should be examined for equivalent compliance with the weight tolerance limits of Figure 3-1. An example would be the reduction of an airplane’s landing flap position, to one approved on a similar model of the same airplane type, which would incur an increase in landing speeds and brake energy, relative to the original certificated landing flap, at any given weight. The brake energy, at the maximum certificated landing weight, should be calculated for the reduced landing flap. This brake energy should account for the increased landing speeds and reduced aerodynamic drag associated with the reduced flap setting. It should then be determined what “equivalent” gross weight would have rendered that brake energy with the original landing flap (see Figure 3-2).

The resulting “equivalent” gross weight should not exceed the certificated maximum landing weight by more than the five percent weight extrapolation limit specified in Figure 3-1. If the “equivalent” gross weight (at the existing landing flap setting) is not more than five percent greater than the certificated maximum landing weight, the reduced flap certification

may be eligible for a limited flight test program (e.g., stall speed verification, handling characteristics, and qualitative landing demonstration). Further limitations may be imposed by the criteria of Technical Standard Order (TSO) C26c (“Aircraft Wheels and Wheel-Brake Assemblies, with Addendum I,” dated May 18, 1984), wheel fusible plug energy limits, quick turnaround considerations, the maximum demonstrated kinetic energy level, wheel spin-up loads, etc.

FIGURE 3-2. EQUIVALENT WEIGHT EXTRAPOLATION

e meanerodynamic-chord (MAC), as deter

ble. If performance data are obtained with winds greater than 5 knots, these data should ot n ce sari

(B) Wind Limits. For takeoff and landing tests, a wind velocity limit of 10 knots (from any direction) or 0.12 VS1 (whichever is lower) at the height of th a mined with the airplane in a static ground attitude, has been considered the maximum acceptable. When test wind velocity is to be measured at the wing MAC height, a measurement height of six feet above the ground should be considered as a limit to avoid possible measurement inaccuracies due to surface interference. Because of likely unsteady wind conditions, it is generally considered that takeoff and landing performance data obtained under runway wind conditions greater than 5 knots are likely to be inconsistent and unrelia n e s ly be ignored. (C) C.G. Limits. A test tolerance of +7 percent of the total c.g. range is intended to allow some practical relief for inflight c.g. movement. This relief is only acceptable when the test data general scatter is on both sides of the limiting c.g. or when c.g. correction fro test c.g. to limit c.g. is acceptable.

m

(D) Airspeed Limits. Normally, tests conducted within 3 percent or 3 knots (whichever is the higher) of the desired test speed are considered acceptable.

(E) Thrust Limits. Thrust critical tests, such as minimum control speeds, should be conducted at the highest thrust (power) allowable on the engine given the constraints

f temperature and altitude. It is then permitted to calculate further corrections to allow xtra d

ay thrust, unless a detailed analysis is performed (see Appendix 3 of this C).

tiation, it is not the purpose of these tolerances to allow flights at values in excess of ose authorized in the type design. If such flights are to be conducted, adequate structural substa ys onducted under controlled conditions and with the flight test crew’s full cognizance of the si mples of such flights are: (A) Takeof r a m the purp reaching a test area at the maximum takeoff weight. (B) Landing rea than m weights during the course of co s. hts to obtain data for future approvals beyond that substantiated for the in in re indica he case which corrections are normally al fl t test data should be made by methods that are agreed to by the

o e polation of ata to cover the entire operating envelope. These thrust corrections are limited to 5 percent of test d A (iii) Because the tolerance values normally are not considered in the airplane design substan th

ntiation for the flight conditions should be available. These flights, however, are alwa c

tuation. Exa

f at g eater th n maximu takeoff weight for ose of

at g ter aximum landing nducting takeoff test

(C) Flig itial type design.

(iv) The table

ctions to

F u ig 3 -3 tes t s in lowed. Any corre AA.

igh F

FIGURE 3-3. TEST PARAMETERS THAT NORMALLY CAN BE CORRECTED

Flight Test Condition

Correctable Parameters

Wt. C.G. Airspeed Altitude Power/ Wind Thrust Airspeed calibration X --- --- --- --- --- Stall speeds X X --- --- X --- Climb performance X X X X X --- Landing performance X --- X X --- X Takeoff performance X X --- X X X Accelerate-stop perf. X X --- X X X Minimum control speed --- --- --- --- X --- Minimum unstick speed X X X --- X --- Buffet boundary X X --- X --- ---

(v) All ins d be appropriately alibrated and acceptable to the FAA test team.

trumentation used in the flight test program shoul c (4) Section 25.21(f) - Proof of Compliance (Wind Measurement and Corrections). The relationship between the wind measured at one height and the corresponding wind at another height may be obtained by the following equation: VW2 = VW1(H2/H1)1/7

Where: H = Height above the runway surface VW2 = Wind velocity at H2 VW1 = Wind velocity at H1 This equation is presented graphically below. Values of H less than 5 feet should not be used in this relationship.

FIGURE 3-4. WIND PROFILE VARIATION

(5) Wind Profile Variation for Test Data. The performance data of airplanes should be

e determined. The test orded he rface to the height of on is not measured, the in paragr

Other methods have also been found

obtained in such a manner that the effect of wind on the test data may b wind velocity should be corrected from the rec ight above the test su the airplane wing mean-aerodynamic-chord. If the wind profile variati variation may be calculated using the equation aph (4) above. The following examples are methods of handling wind profile variation data. acceptable.

0 0 3

10

60

70

0 40 50 6

WIND VELOCITY - KNOTS

I A - FEET

20

BO

30

40

50

VE FIELD ELEVATION

10 meters

GHT HE

0 10 2 0

Example: Test Data Given: o Height of mean-aerodynamic-chord with airplane on surface 8 ft. o Height of wind measurement 6 ft. 4.8 kts. o Measured wind velocity Results: o Test wind velocity with airplane 50 ft. above landing surface

4.8((50 + 8)/6)1/7 = 5 ft. above takeoff surface 4.8((35 + 8)/6)1/7 = 6.4 kts. Test wind velocity with airplane on surface

5.0 kts.

ta

6.6 kts. o Test wind velocity with airplane 3 o 4.8(8/6)1/7 = (6) Wind Profile Variation for Airplane Flight Manual (AFM) Da . When expanding

ty lane’s ing wind condition as measured at 10

f (1).

the data to the AFM conditions, the result should include the effective veloci , at the airp w mean-aerodynamic-chord, which corresponds to the meters (32.81 ft.) above the takeoff surface, and corrected for wind factors o § 25.105(d) Example: Airplane Flight Manual Data Given: o Height of mean-aerodynamic-chord with airplane on surface 8.0 ft. o Reported head wind at 10 meters 40.0 kts. o Section 25.105(d)(1) wind factor 0.5 Results: o Factored wind velocity with airplane 50 ft. above landing surface

(0.5)(40)((50 + 8)/32.81)1/7 = 21.7 kts. 5 ft. above takeoff surface )((35 + 8)/32.81)1/7 = ty th irpl ne on surface

(8/32.81)1/7 = 1

Airplane Airspeed Variation Due to Wind Profile Variation With Simultaneous

o Factored wind velocity with airplane 3 (0.5)(40 20.8 kts. o Factored wind veloci wi a a (0.5)(40) 6.3 kts. (7) Speed Changes Due to Airplane Dynamic Performance. In the reduction of test data and in the

xpa io dynamic ifested by only the change in ground speed. These hanges in speed (zero wind speed changes) may be generalized either as speed increments or

rofile are superimposed on these speed hanges.

e ns n of such data to AFM conditions, the increase or decrease of speed due to the effect of the forces on the airplane are man c speed ratios. The changes in airspeed due to wind p c

E p e: Takeoff Test Data xam l Given:

ff surface o Test wind at liftoff 5.0 kts. . above takeoff surface 6.4 kts.

esults

o True airspeed at liftoff, VLOF 144 kts. o True airspeed at 35 ft. above takeo 147 kts. o Test wind with airplane 35 ft R :

lan dy performance, d

xampl Manual Data

ive

o Speed change due to airp e namic zero wind spee change (V35-VLOF) = (147-6.4)-(144-5.0) 1.6 kts. E e: Takeoff--Airplane Flight G n: o Factored wind at liftoff 16.3 kts. o Factored wind with airplane 35 ft. above takeoff surface 20.8 kts. o Zero wind speed change, (V35-VLOF) 1.6 kts. o Zero wind speed change, (VLOF-VR) 0.5 kts. o True airspeed required at 35 ft. 150 kts. Results: o Ground speed required at 35 ft. 150-20.8 = 129.2 kts. o Ground speed at liftoff 129.2-1.6 = 127.6 kts. o True airspeed at liftoff 127.6+16.3 = 143.9 kts. o Ground speed at rotation 127.6-0.5 = 127.1 kts.

(for distance calculations) 127.1+16.3 = 143.4 kts. Airplane flight manual rotation speed, true airspeed 150-0.5-1.6 = 147.9 kts.

o True airspeed at rotation o NOTE: The indicated airspeed at rotation (V the AFM, should be predicated on the

e change” increments shown above). The proper tation speed, assuming the airplane will gain 4.5 knots due to wind profile, is 143.4 knots.

if this airspeed increase does not materialize, the airplane will be slow by 4.5 knots at 5 feet. It is therefore more desirable to allow the airplane to attain this 4.5 knots on the ground. ny gin s ety by this increase in sated r b s a o eliminates a requir d. e d le gths, the airspeed a ay be cluded.

R), given in required speed at 35 ft. minus the speed increment (V35-VR) assuming no airspeed change due to wind profile (i.e., use the “zero wind spe d ro However, 3 A reduction in field length mar of af VR is adequately compen fo y the 50 percent wind factor. Thi ls ement to adjust VR for win Howev r, in calculating the AFM fiel n ttained due to wind profile m in

Example: Landing--Airplane Flight Manual Data Given: o F ored wind with airplane 50 ft. above landing surface 21.7 kts. o Factored wind with airplane on landing surface 16.3 kts. o Zero wind speed change for 50 ft. to touchdown (V

act

50-VTD) 4.0 kts. o True airspeed required at 50 ft. 130 kts. Results: o Ground speed at 50 ft. 130-21.7 = 108.3 kts. o Ground speed at touchdown 108.3-4.0 = 104.3 kts. o True airspeed at touchdown 104.3+16.3 = 120.6 kts. (8) Expansion of Takeoff Data for a Range of Airport Elevations. (i) These guidelines are applicable to expanding takeoff data above the altitude at which the basic or verifying tests were obtained. (ii) In general, takeoff data may be extrapolated above and below the altitude at

traints.

-

by gine

at tion

(iii) When the basic takeoff test data are obtained between sea level and

tion. If it is desired to extrapolate beyond these limits, when roven data reduction and expansion methods are used, one of the two following procedures may

(A) Extrapolation of Performance Data for a Range of Altitudes When

which the basic test data was obtained without additional conservatism within certain cons The extrapolation limits and constraints for expansion of the measured takeoff performance parameters (e.g., data used to develop V/VS=f(T/W)) to operating altitudes is addressed in sub paragraph 3a(9)(iii), below. Extrapolation of takeoff performance data may be further limited engine data extrapolation limits, typically to 3,000 feet above the highest altitude at which en parameters were evaluated for the pertinent power/thrust setting. (See paragraph 9 of this AC for more information on engine testing and data extrapolation.) Certification testing for operation airports that are above 8,000 feet should also include functional tests of the cabin pressuriza system in accordance with paragraph 87b(3) of the AC. approximately 3,000 ft., the maximum allowable extrapolation limits are 6,000 ft. above, and 3,000 ft. below, the test field eleva p be employed: Verifying Tests are Not Conducted. The approval of performance data for airport elevations beyond the maximum elevation permitted by basic tests may be allowed without conducting

erifying tests, if the calculated data include a conservative factor. This conservatism should

mount equal to zero percent for the highest airport elevation approved on the results of the basic

v result in an increase of the calculated takeoff distance at the desired airport elevations by an a tests, and an additional cumulative 2 percent incremental factor for each 1,000 ft. of elevation above the highest airport elevation approved for zero percent conservatism. The 2 percent

incremental factor should have a straight line variation with altitude. When performance data are calculated for the effects of altitude under this procedure, the following provisions are applicab

le:

(1 ) Previously established calculation procedures should be used, taking

(2

into account all known variables. ) The calibrated installed engine power for the pertinent speed and altitude ranges should be used. (3) The brake kinetic energy limits established by airplane ground tests should not be exceeded. (B) Extrapolation of Performance Data When Verifying Tests Are Conducted.

(1 ) If data approval is desired for a greater range of airport elevations, the erf m ce

he orrespond losely to the calculated performance values.

p or an may be calculated from the basic test data up to the maximum airport elevation, provided verifying tests are conducted at appropriate elevations to substantiate the validity of t calculations. The actual airplane performance data from the verifying tests should c c (2) For the verifying tests, it has been found that normally three takeoffs at maximum weights for the elevations tested will provide adequate verification.

(3) If verifying tests substantiate the expanded takeoff data, the data may e further expanded up to 6,000 ft. above the altitude at which the verifying tests were

bove the verifying test altitude, the 2 percent per ,000 ft. cumulative factor discussed in paragraph 3a(9)(iii)(A), above, should be applied,

b conducted. At altitudes higher than 6,000 ft. a 1 starting at zero percent at the verifying test altitude plus 6,000 feet. (9) Expansion of Landing Data for a Range of Airport Elevations.

opellers, the landing distance data may e extrapolated to more than 6,000 ft. above the test altitude without the penalty described in

(10) Tailwind Takeoff and Landing

(i) For turbine powered airplanes without pr b paragraph 3a(9), provided the true airspeed effect on the distance is accounted for. (ii) For turbopropeller and reciprocating engine-powered airplanes, the extrapolated performance should include the conservative factor described in paragraph 3a(9). This may not be necessary if it can be shown that the effects of altitude on the landing performance, as affected by propeller drag, are known from data available for the airplane configuration. .

(i) Wind Velocities of 10 Knots or Less - Approval may be given for performance,

cities

(ii) Wind Velocities Greater than 10 Knots

controllability, and engine operating characteristics for operations in reported tailwind velo up to 10 knots, measured at a 10 meter height, without specific flight tests. . (A) Performance. It is considered that takeoff, rejected takeoff, and landing distances, measured in tailwind conditions greater than 10 knots, are unreliable for use in

gth of the runway or over the time period required to perform e test maneuver. The 150 percent operational tailwind velocity factor, required by

f ro wind conditions.

with tailwinds greater than 0 knots is desired.

determining airplane performance. Wind conditions of such magnitude are generally not sufficiently consistent over the len th §§ 25.105(d)(1) and 25.125(e), affords a satisfactory method for determination of airplane takeoff and landing performance information and limitations up to a limiting tailwind velocity o 15 knots when using a flight test data base obtained under ze NOTE: The design requirements of § 25.479 (Level landing conditions) also require the effects of increased contact speeds to be investigated if approval for landings 1 (B) Control Characteristics. Airplane control characteristics should be evaluated under the following conditions with the center of gravity at the aft limit and the test tailwind velocity equal to the proposed limit tailwind factored by 150 percent: (1) Takeoff. At light weight with maximum approved takeoff flap deflection, both all-engines operating and one-engine inoperative takeoffs should be evaluated. (2) Landing. Approach and landing at light weight with maximum approved landing flap deflection. (3) Determination of the increased ground speed effect on gear vi shimmy, flight director and/or autopilot Instrument Landing System (ILS) approaches, Ground

bration,

roximity Warning Systems (GPWS) sink rate modes, etc.

(4

P ) If engine idle thrust is increased to account for the increased tailwind velocity, ensure that deviations above the glideslope are recoverable. (C) Weight Limits. In accordance with the requirements of §§ 25.105(d)(1) and 25.125(e), maximum takeoff weight and maximum quick turnaround weight should be

etermined using brake energies and tire speeds, as appropriate, calculated with the limit tailwind

50 percent. d velocity factored by 1 (D) Engine Operating Characteristics. Satisfactory engine operation sh demonstrated at the limit tailwind

ould be velocity factored by 150 percent. The demonstrations should clude: in

(1) Zer g n e ation. o rou dsp ed oper (2) Takeoff pow r se rocedure used for AFM p e tting p erformance p oximately 80 nots), b lly (autothrottle). (typically completed by a pr k oth manually and automatica (3) Reverse thrust operations. (E) Airplane Flight Manual. The AFM should contain a statement that th limitation for tailwinds greater than 10 knots reflects the capability of the airplane as evaluate terms of airworthiness but does not constitute approval for operation in tailwinds exceeding 10 knots.

e

d in

b. Procedures. (1) The performance-related flight test procedures are discussed in each of the following paragraphs of this AC: 10. Takeoff and Takeoff Speeds 15. Climb: General

(2) Performance Data for Multiple Flap or Additional Flap Positions

11. Accelerate-Stop Distance 16. Landing Climb 12. Takeoff Path 17. Climb: One Engine Inoperative 13. Takeoff Distance and Takeoff Run 18. En route Flight Path 14. Takeoff Flight Path 19. Landing . If approval of quested for flap settings at which no test data areavailable, the data may be btained from interpolation of flight data obtained at no less than four flap settings that are within a constant configuration of other lift devices. If the span of flap settings is small and previously obtained data provide sufficient confidence (i.e., the shape of the curves are known and lend themselves to accurate interpolation), data from three flap settings may be acceptable. (3) Flight Characteristics for Abnormal Configurations

performance data is re o

(Ref. § 25.671(c)). (i) For purposes of this AC, an abnormal configuration is an operational configuration that results from any single failure or any combination of failures not shown to be improbable. (ii) Flight characteristics for abnormal configurations may be determined by test or analysis to assure that the airplane is capable of continued safe flight and landing. Flight tests, if required, should be conducted at the critical conditions of altitude, weight, c.g., and engine thrust associated with the configuration, and at the most critical airspeed between stall warning (see paragraph 29d(2)(ix) of this AC) and the maximum operating airspeed for the configuration. 4.-7. [RESERVED]

8. PROPELLER SPEED AND PITCH LIMITS - § 25.33. a. Explanation. None. b. Procedures. The tachometers and the airspeed indicating system of the test airplane must have been calibrated in the last six months. With those conditions satisfied, the following should be accomplished: (1) Determine that the propeller speeds and pitch settings are safe and satisfactory during all tests that are conducted in the flight test program within the certification limits of the airplane, engine, and propeller. This includes establishing acceptable low pitch (flight idle) blade angles on turbopropeller airplanes and verifying that propeller configurations are satisfactory at VMO/MMO to prevent propeller overspeed. (2) Determine that the propeller speeds and pitch settings are safe and satisfactory during all tests that are conducted to satisfy the performance requirements.

(3) With the propeller governors operative and the propeller controls in full high r.p.m. position, determine that the maximum takeoff power settings do not exceed the rated takeoff r.p.m. of each engine during takeoff and climb at the best rate-of-climb speed. (4) With the propeller governors made inoperative by mechanical means, maximum power, no-wind, static r.p.m.’s must be determined. On reciprocating engines with the propeller governors operating on the low pitch stop, the engine speeds must not exceed 103 percent of the maximum allowable takeoff r.p.m. On turbopropeller engines, the engine speeds must not exceed the maximum engine speeds allowed by engine and propeller type designs. Note which systems were disabled and how the disablement was done. If maximum takeoff power torque or sea level standard conditions cannot be obtained on the test day, the data must be corrected to these conditions by an acceptable means. A no-wind condition is considered to be a wind of 5 knots or less.

The static r.p.m. should be the average obtained with a direct crosswind from the left and a direct crosswind from the right. (5) If the above determinations are satisfactory, the low-pitch stop setting and also the high-pitch stop setting must be measured. These data may have been obtained from the propeller manufacturer and may be used, provided the pitch stops have not been changed since the manufacturer delivered the propeller. If measured, the blade station should be recorded. These blade angles must be included in the Type Certificate Data Sheet.

Chap 2 43 (thru 70)

This page intentionally left blank

Section 2. PERFORMANCE 9. GENERAL - § 25.101 a. Explanation - Engine Behavior. Section 25.101(c) requires that airplane “performance must correspond to the propulsive thrust available under the particular ambient atmospheric conditions, the particular flight conditions.... Therefore, engine parameter evaluations, engine torque, thrust lapse, propeller thrust, and throttle sensitivity, especially with the Electronic Control Unit off (if installed), should be accounted for at all altitudes up to and including the maximum approved takeoff altitude. b. Procedures. This aspect of the rule may be accomplished by actual flight test, with approved takeoff ratings, at the maximum desired takeoff altitude, or with acceptable parameter variation analysis associated with tests conducted at less than the maximum objective takeoff altitude. (1) One acceptable method of demonstrating high altitude engine operability and performance is to simulate the maximum operating altitude conditions by overboosting (i.e., using a higher than normal power setting) at a lower altitude.

(2) It is the applicant’s responsibility, in conjunction with the engine manufacturer, to define the test plan for the engine parameter evaluation up to the maximum approved takeoff altitude. Supportive data from the engine manufacturer on the same “type or series” of engine may also be included to reduce the amount of testing conducted. (3) Extrapolation of engine performance data to 3,000 feet above the highest altitude tested (up to the maximum takeoff altitude to be approved) has been accepted, provided the supportive data, including the flight testing accomplished, establishes a consistent baseline. (4) Detailed guidance for the testing necessary to show compliance with § 25.101(c) may be found in Advisory Circular 25-XX, “Turbojet Operations at High Altitude Airports,” dated (to be released). 10. TAKEOFF AND TAKEOFF SPEEDS - §§ 25.105 AND 25.107 (PART 25 AS AMENDED THROUGH AMENDMENT 25-42). a. Explanation.

The primary objective of the takeoff tests required by § 25.107 is to determine the takeoff speed schedule for all takeoff configurations at all weight, altitude, and temperature conditions within the operational limits selected by the applicant. The provisions of § 25.105 are self evident and are not repeated or amplified in this discussion. Guidance material for unpaved runway evaluation is contained in Chapter 8 (paragraph 234) of this Advisory Circular (AC).

AC 25-7A 6/3/99 Chg. 1

b. Procedures. Although the following speed definitions are given in terms of calibrated airspeed, the Airplane Flight Manual (AFM) presentations shall be given in terms of indicated airspeed. Attention should be paid to all potential sources of airspeed error, but special consideration should be given to airplanes with electronic instruments in the cockpit that apply electronic filtering to the airspeed data. This filtering, which causes a time delay in the airspeed indication, can be a source of significant systematic error in the presentation of airspeed to the flightcrew. During a normal takeoff acceleration, the airplane will be at a higher speed than is indicated by the cockpit instrument, which can result in longer distances than are presented in the AFM, particularly in the event of a rejected takeoff near the indicated V1 speed. The effects of any time delays caused by electronic filtering, pneumatic system lag, or other sources should be adequately addressed in the AFM speed and distance presentations.

Further explanation of airspeed lag, particularly pertaining to airplanes with electronic instruments in the cockpit, and procedures for calibrating the airspeed indicating system (§ 25.1323(b)) are presented in paragraph 177 of this AC. (1) Section 25.107(a)(1) - Engine Failure Speed (VEF). The engine failure speed (VEF) is defined as the calibrated airspeed at which the critical engine is assumed to fail and must be selected by the applicant. VEF cannot be less than the ground minimum control speed (VMCG) as described in §§ 25.149(e) and 25.107(a)(1). (2) Section 25.107(a)(2) - Takeoff Decision Speed (V1). The takeoff decision speed (V1) may not be less than VEF plus the speed gained with the critical engine inoperative during the time interval between VEF and the instant at which the pilot takes action after recognizing the engine failure. This is indicated by pilot application of the first deceleration device such as brakes, throttles, spoilers, etc. during accelerate-stop tests, or by the first control input during VMCG testing. The applicant may choose the sequence of events.

Refer to paragraph 11 of this AC, addressing § 25.109, for a more complete description of RTO transition procedures and associated time delays. If it becomes evident in expansion of takeoff data for the AFM that excessive variation in V1 exists, resulting from the many performance variables involved (variations of +1.5 knots or +100 ft. have been found acceptable), then measures must be taken to ensure that scheduled performance variations are not excessive. Examples of such measures are small field length factors, or increments, and multiple web charts (accelerate-go/stop, V1/VR) for a particular configuration. (3) Section 25.107(b) - Minimum Takeoff Safety Speed (V2MIN). (i) V2MIN, in terms of calibrated airspeed, cannot be less than: (A) 1.1 times the VMCA defined in § 25.149. (B) 1.2 times VS for two-engine and three-engine turbopropeller and reciprocating engine-powered airplanes and for all turbojet airplanes that do not have provisions for obtaining significant reduction in the one-engine inoperative power-on stalling speed (i.e., boundary layer control, blown flaps, etc.).

The value of VS to be used in determining V2MIN is

the stall speed in the applicable takeoff configuration, landing gear retracted, except for those airplanes with a fixed landing gear or for gear-down dispatch. (ii) V2MIN may be reduced to 1.15 times VS for turbopropeller and reciprocating engine-powered airplanes with more than three engines, and turbojet powered airplanes with adequate provisions for obtaining significant power-on stall speed reduction through the use of such things as boundary layer control, blown flaps, etc. (iii) For propeller-driven airplanes, the difference between the two margins, based upon the number of engines installed on the airplane, is because the application of power ordinarily reduces the stalling speed appreciably. In the case of the two-engine propeller-driven airplane, at least half of this reduction is eliminated by the failure of an engine.

The difference in the required factors therefore provides approximately the same margin over the actual stalling speed under the power-on conditions that are obtained after the loss of an engine, no matter what the number of engines (in excess of one) may be. Unlike the propeller-driven airplane, the turbojet/turbofan powered airplane does not show any appreciable difference between the poweron and power-off stalling speed. This is due to the absence of the propeller, which ordinarily induces a slipstream with the application of power causing the wing to retain its lift to a speed lower than the power-off stalling speed. The applicant’s selection of the two speeds specified will influence the nature of the testing required in establishing the takeoff flight path. (4) Section 25.107(c) - Takeoff Safety Speed (V2). V2 is the calibrated airspeed that is attained at or before the airplane reaches a height of 35 ft. above the takeoff surface after an engine failure at VEF using an established rotation speed (VR).

During the takeoff speeds demonstration, V2 should be continued to an altitude sufficient to assure stable conditions beyond the 35 ft height. V2 cannot be less than V2MIN. In addition, V2 cannot be less than the liftoff speed, VLOF, as defined in § 25.107(f). In accordance with § 25.107(c), V2 in terms of calibrated airspeed “...may not be less than VR plus the speed increment attained before reaching a height of 35 feet above the takeoff surface. Section 25.111(c)(2) stipulates that the airplane must reach V2 before it is 35 feet above the takeoff surface and continue at a speed not less than V2 until it is 400 feet above the takeoff surface. These requirements were first expressed in SR-422A, paragraphs 4T.114(b)(4) and (c)(3) and 4T.116(e). The intent of these requirements is discussed in the preamble to SR-422A, which states, in part, “For these reasons, this regulation permits the airplane to lift off the ground at a speed lower than the V2 speed.

The concern that the regulation change was addressing was the overshoot of V2 after liftoff when it was required that the airplane attain V2 on, or near, the ground. It was therefore the intent of the regulation to allow an acceleration to V2 after liftoff but not to allow a decrease in the field length required to attain a height of 35 feet above the takeoff surface by attaining a speed greater than V2, under low drag ground conditions, and using the excess kinetic energy to attain the 35 foot height. (i) In the case of turbojet powered airplanes, when the bulk of the one-engineinoperative data have been determined with idle cuts, V2, and its relationship to VR, should be substantiated by a limited number of fuel cuts at VEF. For derivative programs not involving a new or modified engine type (i.e., a modification that would affect thrust decay characteristics), fuel cuts are unnecessary if thrust decay characteristics have been adequately substantiated.

(ii) For propeller-driven airplanes, the use of fuel cuts can be more important in order to ensure that the takeoff speeds and distances are obtained with the critical engine’s propeller attaining the position it would during a sudden engine failure. The number of tests that should be conducted using fuel cuts, if any, depends on the correlation obtained with the idle cut data and substantiation that the data analysis methodology adequately models the effects of a sudden engine failure. (5) Section 25.107(d) - Minimum Unstick Speed (VMU). (i) An applicant should comply with § 25.107(d) by conducting minimum unstick speed (VMU) determination tests with all engines operating and with one engine inoperative. If a stick pusher is installed, it should normally be active and set to the minimum angle of attack side of its rigging tolerance band. If desired, artificial stall warning systems may be disabled for this demonstration. (See paragraph (vi) below for further discussion regarding the setting of stick pusher and stall warning systems during VMU testing.

During this demonstration, the takeoff should be continued until the airplane is out of ground effect. The airplane pitch attitude should not be decreased after liftoff. (ii) In lieu of conducting actual one-engine-inoperative VMU tests, the applicant may conduct all-engines-operating VMU tests that simulate and account for all pertinent factors that would be associated with an actual one-engine-inoperative VMU test. To account fully for pertinent factors, it may be necessary to adjust the resulting VMU test values analytically. The factors to be accounted for must at least include the following: (A) Thrust/weight ratio for the one-engine-inoperative range. (B) Controllability (may be related to one-engine-inoperative free air tests, such as VS, VMCA, etc.). (C) Increased drag due to lateral/directional control systems. (D) Reduced lift due to devices such as wing spoilers used for lateral control.

(E) Adverse effects of any other systems or devices on control, drag, or lift. (iii) The number of VMU tests required may be minimized by testing only the critical all-engines-operating and one-engine-inoperative thrust/weight ratios, provided that the VMU speeds determined at these critical conditions are used for the range of thrust/weights appropriate to the all-engines-operating and one-engine-inoperative configurations. The critical thrust/weight is established by correcting, to the VMU speed, the thrust that results in the airplane achieving its limiting one-engine-inoperative climb gradient at the normally scheduled speed and in the appropriate configuration.

(iv) Amendment 25-42, effective March 1, 1978, revised §§ 25.107(d) and 25.107(e)(1)(iv) in order to permit the one-engine-inoperative VMU to be determined by allengines-operating tests at the thrust/weight ratio corresponding to the one-engine-inoperative condition. As revised, § 25.107(d) specifies that VMU must be selected for the range of thrust/weight ratios to be certificated, rather than for the all-engines-operating and one-engineinoperative conditions as was previously required. In determining the all-engines-operating thrust/weight ratio that corresponds to the one-engine-inoperative condition, consideration should be given to trim and control drag differences between the two configurations in addition to the effect of the number of engines operating.

The minimum thrust/weight ratio to be certificated is established by correcting, to the VMU speed, the thrust that results in the airplane achieving its limiting engine-out climb gradient in the appropriate configuration and at the normally scheduled speed. (v) To conduct the VMU tests, rotate the airplane as necessary to achieve the VMU attitude. It is acceptable to use some additional nose-up trim over the normal trim setting during VMU demonstrations. If additional nose-up trim is required, the additional considerations of paragraph (vii), below, apply. VMU is the speed at which the weight of the airplane is completely supported by aerodynamic lift and thrust forces. Some judgment may be necessary on airplanes that have tilting main landing gear bogies. Determining the liftoff point from gear loads and wheel speeds has been found acceptable in past programs. After liftoff, the airplane should be flown out of ground effect.

During liftoff and the subsequent climbout, the airplane should be fully controllable. (vi) VMU testing is a maximum performance flight test maneuver, and liftoff may occur very near the angle of attack for maximum lift coefficient. Also, even though pitch attitude may be held fairly constant during the maneuver, environmental conditions and transiting through ground effect may result in consequential changes in angle of attack. It is permissible to lift off at a speed that is below the normal stall warning speed, provided no more than light buffet is encountered. An artificial stall warning system (e.g., a stick shaker) may be disabled during VMU testing, although doing so will require extreme caution and depend upon a thorough knowledge of the airplane’s stall characteristics. If the airplane is equipped with a stick pusher, for flight test safety reasons it should normally be active and set to the minimum angle of attack side of its rigging tolerance band.

However, depending on the airplane’s stall characteristics and the stick pusher design, disabling the pusher or delaying activation of the system until a safe altitude is reached may be the safer course. Again, this decision should be made only with a thorough knowledge of the airplane’s stall characteristics combined with a complete understanding of the stick pusher design. (vii) VMU Testing for Airplanes Having Limited Pitch Control Authority. (A) For some airplanes with limited pitch control authority, it may not be possible, at forward c.g. and normal trim, to rotate the airplane to a liftoff attitude where the airplane could otherwise perform a clean flyaway at a minimum speed had the required attitude been achieved. This may occur only over a portion of the takeoff weight range in some configurations. When limited pitch control authority is clearly shown to be the case, VMU test

conditions may be modified to allow testing aft of the forward c.g. limit and/or with use of more airplane nose-up trim than normal. The VMU data determined with this procedure should be corrected to those values representative of the appropriate forward limit; the variation of VMU with c.g. may be assumed to be like the variation of free air stalling speed with c.g. Although the development of scheduled takeoff speeds may proceed from these corrected VMU data, additional tests are required (see paragraph (B) below) to check that the relaxed VMU criteria have not neglected problems that might arise from operational variations in rotating airplanes with limited pitch control authority. (B) In the following assurance test, the airplane must demonstrate safe flyaway characteristics. (1) Minimum speed liftoff should be demonstrated at the critical forward c.g. limit with normal trim. For airplanes with a cutback forward c.g. at heavy weight, two weight/c.g. conditions should be considered.

The heavy weight tests should be conducted at maximum structural or maximum sea level climb-limited weight with the associated forward c.g. The full forward c.g. tests should be conducted at the highest associated weight. These tests should be conducted at minimum thrust/weight for both the simulated one-engine-inoperative test (symmetrical reduced thrust) and the all-engines-operating case. (2) One acceptable test technique is to hold full nose-up control column as the airplane accelerates. As pitch attitude is achieved to establish the minimum liftoff speed, pitch control may be adjusted to prevent overrotation, but the liftoff attitude should be maintained as the airplane flies off the ground and out of ground effect. (3) Resulting liftoff speeds do not affect AFM speed schedules if the test proves successful and the resulting liftoff speed is at least 5 knots below the normally scheduled liftoff speed. Adjustments should be made to the scheduled VR, forward c.g. limit, etc., if necessary, to achieve this result.

(4) This minimum 5 knot reduction below the scheduled liftoff speed provides some leeway for operational variations such as mis-trim, c.g. errors, etc., that could further limit the elevator authority. The reduced VMU margins of the minimum liftoff speeds demonstrated in this test, relative to those specified in § 25.107(e)(1)(iv), result from the reduced probability of a pitch control authority-limited airplane getting into a high drag condition due to overrotation. (viii) VMU Testing for Geometry Limited Airplanes. (A) For airplanes that are geometry limited, the 110 percent of VMU required by § 25.107(e)(1)(iv) may be reduced to an operationally acceptable value of 108 percent on the basis that equivalent airworthiness is provided for the geometry limited airplane. For acceptance of the 108 percent of VMU liftoff speed, safeguards protecting the geometry limited airplane against both overrotation on the ground and in the air must be provided. Also, the airplane should be geometry limited to the extent that a maximum gross weight takeoff with the tail

dragging will result in a clean liftoff and fly-away in the all-engines-operating condition. During such a takeoff for the all-engines-operating condition, the resulting distance to the 35 ft. height must not be greater than 105 percent of the normal takeoff distance under similar weight, altitude, and temperature conditions before the 15 percent margin is added. Lastly, the VMU demonstrated must be sound and repeatable. Compliance with these criteria should be formally addressed in a finding of equivalent safety. (B) The criteria for demonstrating the capability for a clean liftoff and flyaway are as follows: (1) The airplane’s pitch attitude from a speed of 96 percent of the actual liftoff speed must be within 5 percent (in degrees) of the tail dragging attitude to the point of liftoff. (2) During the above speed range (96 to 100 percent of the actual liftoff speed), the aft under-surface of the airplane must have achieved actual runway contact. It has been found acceptable in tests for contact to exist approximately 50 percent of the time that the airplane is in this speed range.

(3) Beyond the point of liftoff to a height of 35 ft., the airplane’s pitch attitude must not decrease below that at the point of liftoff, or the speed must not increase more than 10 percent. (4) The airplane shall be at the critical thrust/weight condition, as defined in § 25.107(d), but with all engines operating. (ix) VMU for a Stretched Version of a Tested Airplane. (A) It has been considered that the VMU speed represents the aerodynamic potential minimum liftoff speed related to a safe liftoff and fly-away, even though the body contact attitude may prevent achieving the lift coefficient (CL) for this speed. Such is the case when VMU is determined with body contact, whether or not geometry-limited “credit” is sought. It is therefore concluded that a VMU schedule obtained on one model of an airplane type may be applied to a geometry-limited stretched version of that tested airplane. The 108 percent speed factor of paragraph 10b(5)(viii)(A), above, is only applicable to the stretched version if it was applicable to the tested airplane.

(B) Since the concern for tail strikes is increased with the stretched airplane, the following shall be accomplished, in addition to normal takeoff tests, when applying a shorter body airplane’s VMU schedule to the stretched derivative: (1) Scheduled rotation speeds (VR) for the stretched airplane should result in at least the required liftoff speed margins above VMU (i.e., 1.05 and 1.10 or 1.08, as applicable) of the shorter body airplane, corrected for the reduced runway pitch attitude capability and revised c.g. range of the stretched airplane.

(2) At both the forward and aft c.g. limits, and over the thrust-to-weight range for each takeoff flap, the following abuse takeoff tests must be accomplished. The tests described in paragraphs (i) and (ii), below, should be accomplished with not more than occasional, minor (i.e., non-damaging) tail strikes. (i) All-engines-operating, early rotation abuse tests specified in paragraph 10b(6)(iii)(B), including both the rapid rotations and over-rotations as separate test conditions. (ii) One-engine-inoperative, early rotation abuse tests specified in paragraph 10b(6)(ii). (iii) All-engines-operating, moderate rotation rate (i.e., more rapid than normal) takeoff abuse tests, using the scheduled VR, and normal pitch attitude after liftoff. No tail strikes may occur for this condition. (6) Section 25.107(e) - Rotation Speed (VR). (i) The rotation speed, (VR) in terms of calibrated airspeed, must be selected by the applicant.

VR has a number of constraints that must be observed in order to comply with § 25.107(e): (A) VR may not be less than V1; however, it can be equal to V1 in some cases. (B) VR may not be less than 105 percent of the air minimum control speed (VMCA). (C) VR must be a speed that will allow the airplane to reach V2 at or before reaching a height of 35 ft. above the takeoff surface. (D) VR must be a speed that will result in liftoff at a speed not less than 110 percent of VMU (unless geometry limited) for the all-engines-operating condition and not less than 105 percent of the VMU determined at the thrust/weight ratio corresponding to the oneengine-inoperative condition for each set of conditions such as weight, altitude, temperature, and configuration when the airplane is rotated at its maximum practicable rate. (ii) Early rotation, one-engine-inoperative abuse test. (A) In showing compliance with § 25.107(e)(3), some guidance relative to the airspeed attained at the 35 ft. height during the associated flight test is necessary.

As this requirement dealing with a rotation speed abuse test only specifies an early rotation (VR-5 knots), it is interpreted that pilot technique is to remain the same as normally used for a one-engineinoperative condition. With these considerations in mind, it is apparent that the airspeed achieved at the 35 ft. point can be somewhat below the normal scheduled V2 speed. However,

the amount of permissible V2 speed reduction must be limited to a reasonable amount as described below. (B) These test criteria are applicable to all unapproved, new, basic model airplanes. They are also applicable to previously approved airplanes when subsequent abuse testing is warranted. However, for those airplanes where the criteria herein are more stringent than that previously applied, consideration will be given to permitting some latitude in the test criteria. (C) In conducting the flight tests required by § 25.107(e)(3), the test pilot shall use a normal/natural rotation technique as associated with the use of scheduled takeoff speeds for the airplane being tested. Intentional tail or tail skid contact is not considered acceptable. Further, the airspeed attained at the 35 ft. height during this test must not be less than the scheduled V2 value minus 5 knots. These speed limits should not be considered or used as target V2 test speeds, but rather are intended to provide an acceptable range of speed departure below the scheduled V2 value.

(D) In this abuse test, the simulated engine failure should be accomplished sufficiently in advance of the VR test speed to allow for engine spin-down, unless this would be below the VMCG, in which case VMCG should govern. The normal one-engine-inoperative takeoff distance may be analytically adjusted to compensate for the effect of the early thrust reduction. Further, in those tests where the airspeed achieved at the 35-ft. height is slightly less than the V2-5 knots limiting value, it will be permissible, in lieu of conducting the tests again, to analytically adjust the test distance to account for the excessive speed decrement. (iii) All-engines-operating abuse tests. (A) Section 25.107(e)(4) states that there must not be a “marked increase” in the scheduled takeoff distance when reasonably expected service variations such as early and excessive rotation and out-of-trim conditions are encountered.

This has been interpreted as requiring takeoff tests with all engines operating with: (1) An abuse on rotation speed, and (2) Out-of-trim conditions, but with rotation at the scheduled VR speed. NOTE: The expression “marked increase” in the takeoff distance is defined as any amount in excess of 1 percent of the scheduled takeoff distance. Thus, the abuse tests should not result in field lengths more than 101 percent of the takeoff field lengths calculated in accordance with the applicable requirements of Part 25 for presentation in the AFM. (B) For the early rotation abuse condition with all engines operating, and at a weight as near as practicable to the maximum sea level standard day takeoff weight limit, it should be shown by test that when the airplane is overrotated at a speed below the scheduled VR, no “marked increase” in the scheduled AFM field length will result. For this demonstration, the

AC 25-7A 6/3/99 Chg.1

airplane should be rotated at a speed 7 percent or 10 knots, whichever is less, below the scheduled VR. Tests should be conducted at a rapid rotation rate or should include an overrotation of 2 degrees above normal attitude after liftoff. Tail strikes during this demonstration are acceptable if they are minor and do not result in unsafe conditions. (C) For reasonably expected out-of-trim conditions with all engines operating and as near as practicable to the maximum weight allowed under sea level standard day conditions, it should be shown that there will not be a “marked increase” in the scheduled AFM takeoff distance when rotation is initiated in a normal manner at the scheduled VR speed. (See paragraph 21(b)(7)(ii) for additional guidance regarding the evaluation of flight characteristics for out-of-trim conditions. The amount of mistrim should be the maximum mistrim that would not result in a takeoff configuration warning, including taking into account the takeoff configuration warning system rigging tolerance.

It is permissible to accept an analysis in lieu of actual testing if the analysis shows that the out-of-trim condition would not present unsafe flight characteristics or “marked increase” in the scheduled AFM field lengths. (iv) Stall Warning During Takeoff Speed Abuse Tests. The presumption is that if an operational pilot was to make an error in takeoff speeds that resulted in an encounter with stall warning, the likely response would be to aggressively recover to a safe flight condition rather than making a conscious effort to duplicate the AFM takeoff performance data. Therefore, the activation of any stall warning devices, or the occurrence of airframe buffeting during takeoff speed abuse testing, is unacceptable. (7) Section 25.107(f) - Liftoff Speed (VLOF). The liftoff speed (VLOF) is defined as the calibrated airspeed at which the airplane first becomes airborne (i.e., no contact with the runway). This allows comparison of liftoff speed with tire limit speed.

VLOF differs from VMU in that VMU is the minimum possible VLOF speed for a given configuration, and depending upon landing gear design, VMU liftoff is shown to be the point where all of the airplane weight is being supported by airplane lift and thrust forces and not any portion by the landing gear. For example, after the VMU speed is reached, a truck tilt actuator may force a front or rear wheel set to be in contact with the runway, even though the flyoff is in progress by virtue of lift being greater than weight. *11. ACCELERATE-STOP DISTANCE - § 25.109. a. Explanation. This section describes test demonstrations and data expansion methods necessary to determine accelerate-stop distances for publication in the FAA-approved Airplane Flight Manual (AFM), as required by § 25.1583(h) (by reference to § 25.1533). Amendment 25-92 revised some aspects of the Part 25 accelerate-stop criteria and added new requirements related to the stopping capability of the airplane as affected by brake wear and wet runways.

The changes imparted to the accelerate-stop requirements by Amendment 25-92 are listed below. (For other material related to the use of accelerate-stop distances, see Parts 121 and 135 of the FAR.) *

6/3/99 AC 25-7A Chg. 1

(1) Section 25.101(i) was added to require accelerate-stop distances to be determined with all the airplane wheel brake assemblies at the fully worn limit of their allowable wear range. (2) Section 25.105(c)(1) was revised to require takeoff data to be determined for wet, in addition to dry, hard surfaced runways. At the applicant’s option, takeoff data may also be determined for wet runways that have grooved or porous friction course surfaces. (3) Section 25.107(a)(2) was revised to remove the reference to “takeoff decision speed” from the definition of V1. (4) Section 25.109 was revised to add a requirement to determine accelerate-stop distances for wet runways. Additionally, the requirement for the AFM expansion to include two seconds of continued acceleration beyond V1, with the operating engines at takeoff thrust, as introduced by Amendment 25-42, was replaced with a distance increment equivalent to two seconds at V1.

Also, the text of § 25.109(a) was modified to clarify that the accelerate-stop distances must take into account the highest speed reached during the rejected takeoff maneuver, including, as applicable, speeds higher than V1. (5) Section 25.109(f) was added to permit credit for the use of reverse thrust in determining wet runway accelerate-stop distances (subject to the requirements of § 25.109(e)) and to explicitly deny reverse thrust credit for determining dry runway accelerate-stop distances. (6) Section 25.109(i) was added to require a maximum brake energy accelerate-stop test to be conducted with not more than 10 percent of the allowable brake wear range remaining on each individual wheel-brake assembly. (7) Section 25.735(h) was added to require the maximum rejected takeoff brake energy absorption capacity rating used during qualification testing to the applicable Technical Standard Order to be based on the fully worn limit of the brake’s allowable wear range.

(8) Section 25.1533(a)(3) was revised to add runway surface condition (dry or wet) as a variable that must be accounted for in establishing minimum takeoff distances. Section 25.1533(a)(3) was also revised to allow wet runway takeoff distances on grooved and porous friction course (PFC) runways to be established as additional operating limitations, but approval to use these distances is limited to runways that have been designed, constructed, and maintained in a manner acceptable to the FAA Administrator. b. The applicable Federal Aviation Regulations (FAR) are § 25.109, and the following: § 25.101(f) Airplane configuration and procedures. § 25.101(h) Pilot retarding means time delay allowances. § 25.101(i) Worn brake stopping performance.

Chap 2 80-1

AC 25-7A 6/3/99 Chg. 1

§ 25.105 Takeoff configuration and environmental and runway conditions. §§ 25.107(a)(l) & (2) Defines V1 and VEF speeds. § 25.735 Brakes. § 25.1301 Function and installation. § 25.1309 Equipment, systems, and installation. § 25.1533 Additional operating limitations - maximum takeoff weights and minimum takeoff distances. § 25.1583(h) FAA-approved Airplane Flight Manual - operating limitations. § 25.1587 FAA-approved Airplane Flight Manual - performance information. c. Procedures. The following paragraphs provide guidance for accomplishing acceleratestop flight tests and expanding the resulting data for the determination of AFM performance information. (1) Accelerate-stop testing. The following guidance is applicable to turbine-powered airplanes with and without propellers. Guidance regarding flight testing applies only to dry runway accelerate-stop distances. Guidance for expanding the flight test data to determine AFM distances applies to both dry and wet runways, unless otherwise noted.

Further guidance for determining wet runway accelerate-stop distances is provided in paragraph 11c(4). (i) In order to establish a distance that would be representative of the distance needed in the event of a rejected takeoff, where the first action to stop the airplane is taken at or below V1, a sufficient number of test runs should be conducted for each airplane configuration specified by the applicant. (For intermediate configurations, see paragraph 3 of this advisory circular.) (ii) The guidance outlined in paragraph 11c(3) describes how to apply the appropriate time delays, as required by § 25.101(h)(3), for the flightcrew to accomplish the rejected takeoff operating procedures. (iii) Section 25.101(i) states that the accelerate-stop distances must be determined with all the airplane wheel-brake assemblies at the fully worn limit of their allowable wear range. The fully worn limit is defined as the amount of wear allowed before the brake must be removed from the airplane for overhaul. The allowable wear should be defined in terms of a linear

80-2 Chap 2

6/3/99 AC 25-7A Chg. 1

dimension in the axial direction, which is typically determined by measuring the wear pin extension. (A) The only accelerate-stop test that must be conducted at a specific brake wear state is the maximum brake kinetic energy demonstration, which must use brakes that have no more than 10 percent of the allowable brake wear range remaining (see paragraph 11c(2)(iii)). The remainder of the accelerate-stop tests may be conducted with the brakes in any wear state as long as a suitable combination of airplane and dynamometer tests is used to determine the accelerate-stop distances corresponding to fully worn brakes. For example, dynamometer testing may be used to determine whether there is a reduction in brake performance from the wear state used in the airplane tests to a fully worn brake. The airplane test data could then be adjusted analytically for this difference without additional airplane testing. (B) Either airplane-worn or mechanically-worn brakes (i.e., machined or dynamometer worn) may be used.

If mechanically-worn brakes are used, it must be shown that they can be expected to provide similar results to airplane-worn brakes. This comparison can be based on service experience on the test brake or an appropriate equivalent brake, or on dynamometer wear test data when service data are unavailable. (iv) Section 25.109(f)(1) denies credit for the use of reverse thrust as a decelerating means in determining the accelerate-stop distance for a dry runway. This provision applies to both turbine engine and propeller engine reverse thrust. Credit for the additional deceleration available from reverse thrust is permitted for wet runway accelerate-stop distances, provided the thrust reverser system is shown to be safe, reliable, capable of giving repeatable results, and does not require exceptional skill to control the airplane.

(See paragraph 11c(4)(v) for guidance related to obtaining accelerate-stop performance credit for reverse thrust on wet runways.) (v) The accelerate-stop test runs should be conducted at weight/speed combinations that will provide an even distribution of test conditions over the range of weights, speeds, and brake energies for which takeoff data will be provided in the AFM. The effects of different airport elevations can be simulated at one airport elevation, provided the braking speeds employed are relevant for the range of airplane energies that must be absorbed by the brakes. The limiting brake energy value in the AFM shall not exceed the maximum demonstrated in these tests or the maximum for which the brake has been approved.

(See paragraph 11c(2) for further guidance related to tests and analyses for the demonstration of the maximum brake energy absorption capability.) (vi) The V1 speeds used in the accelerate-stop tests need not correspond precisely to the AFM values for the test conditions since it may be necessary to increase or decrease the AFM V1 speed to fully investigate the energy range and weight envelope. (vii) A total of at least six accelerate-stop flight tests should be conducted. Unless sufficient data are available for the specific airplane type showing how braking performance varies with weight, kinetic energy, lift, drag, ground speed, torque limit, etc., at least two tests should be conducted for each configuration when the same braking coefficient of friction is being

Chap 2 80-3

AC 25-7A 6/3/99 Chg. 1

claimed for multiple aerodynamic configurations. These tests must be conducted on hard surfaced, dry runways. (viii) For approval of dispatch capability with anti-skid inoperative, nose wheel brakes or specified main wheel-brake(s) inoperative, autobraking systems, etc., a full set of tests, as in paragraph (vii) above, should normally be conducted. A lesser number of tests may be accepted for “equal or better” demonstrations, to establish small increments or if adequate conservatism is used during testing. (ix) Either ground or airborne instrumentation should include means to determine the horizontal distance time-history. (x) The wind speed and direction relative to the test runway should be determined and corrected to a height corresponding to the approximate height of the mean aerodynamic chord. (See paragraph 3 of this advisory circular.) (xi) The accelerate-stop tests should be conducted in the following configurations: (A) Heavy to light weight as required. (B) Most critical c.g. position. (C) Wing flaps in the takeoff position(s).

(D) Tire pressure: before taxi and with cold tires, set to the highest value appropriate to the takeoff weight for which approval is being sought. (E) Engine idle thrust: set at the recommended upper limit for use on the ground or the effect of maximum ground idle thrust may be accounted for in data analyses. For maximum brake energy and fuse plug no-melt tests, data analysis may not be used in place of maximum ground idle thrust. (xii) Engine thrust should be appropriate to each segment of the rejected takeoff and should include accounting for thrust decay rates (i.e., spindown) for failed or throttled back engines. At the speed that corresponds to the energy level defined for the test demonstration, the stopping sequence is initiated by employing the first acceptable braking means. (A) Turbojet powered airplanes. For AFM calculation purposes, the critical engine failure accelerate-stop data may be based on the failed engine spinning down to a windmilling condition.

(Note: If, due to the certification basis of the airplane, all-engineaccelerate-stop distances are not being considered, the one-engine-inoperative AFM distances should be based on the critical engine failing to maximum ground idle thrust rather than the windmilling condition. The thrust from the operative engine(s) should be consistent with a throttle chop to maximum ground idle thrust. For determining the all-engines-operating dry runway accelerate-stop AFM distances, the stopping portion should be based on all engines

80-4 Chap 2

6/3/99 AC 25-7A Chg. 1

producing maximum ground idle thrust (after engine spindown), as noted in paragraph 11c(1)(xi)(E). The accelerate-stop tests may be conducted with either concurrent or sequential throttle chops to idle thrust as long as the data are adjusted to take into account pilot reaction time, and any control, system, or braking differences (e.g., electrical or hydraulic/mechanical transients associated with an engine failing to a windmilling condition resulting in reduced braking effectiveness). Test data should also be analytically corrected for any differences between maximum ground idle thrust and the idle thrust level achieved during the test. For the criteria relating to reverse thrust credit for wet runway accelerate-stop distances, see paragraph 11c(4)(v). (B) Turbopropeller-powered airplanes. For the one-engine-inoperative accelerate-stop distances, the critical engine’s propeller should be in the position it would normally assume when an engine fails and the power levers are closed.

For dry runway oneengine-inoperative accelerate-stop distances, the high drag ground-idle position of the operating engines’ propellers (defined by a pitch setting that results in not less than zero total thrust, i.e., propeller plus jet thrust, at zero airspeed) may be used provided adequate directional control is available on a wet runway and the related operational procedures comply with §§ 25.109(f) and (h). Wet runway controllability may either be demonstrated by using the guidance available in paragraph 11c(4)(v)(F) at the appropriate power level, or adequate control can be assumed to be available at ground idle power if reverse thrust credit is approved for determining the wet runway accelerate-stop distances. For the all-engines-operating accelerate-stop distances on a dry runway, the high drag ground-idle propeller position may be used for all engines (subject to § 25.109(f) and (h)).

For the criteria relating to reverse thrust credit for wet runway acceleratestop distances, see paragraph 11c(4)(v). (xiii) System transient effects (e.g., engine spin-down, brake pressure ramp-up, etc.) should be determined and properly accounted for in the calculation of AFM accelerate-stop distances (see paragraph 11c(3)(ix)). (2) Maximum Brake Energy Testing. The following paragraphs describe regulatory requirements and acceptable test methods for conducting an accelerate-stop test run to demonstrate the maximum energy absorption capability of the wheel-brakes. (i) The maximum brake energy accelerate-stop demonstration should be conducted at not less than the maximum takeoff weight and should be preceded by at least a 3-mile taxi with all engines operating at maximum ground idle thrust, including three full stops using normal braking.

Following the maximum brake energy stop, it will not be necessary to demonstrate the airplane’s ability to taxi. (ii) Section 25.735(h) requires the rejected takeoff brake kinetic energy capacity rating of each main wheel-brake assembly to be determined at the fully worn limit of its allowable wear range. The calculation of maximum brake energy limited takeoff weights and speeds, for presentation in the AFM performance section, must therefore be based on each airplane main wheel-brake being in the fully worn condition.

Chap 2 80-5

AC 25-7A 6/3/99 Chg. 1

(iii) Section 25.109(i) requires a flight test demonstration of the maximum brake kinetic energy accelerate-stop distance to be conducted with not more than 10 percent of the allowable brake wear range remaining on each of the airplane wheel-brakes. The 10 percent allowance on the brake wear state is intended to ease test logistics and increase test safety, not to allow the accelerate-stop distance to be determined with less than fully worn brakes. If the brakes are not in the fully worn state at the beginning of the test, the accelerate-stop distance should be corrected as necessary to represent the stopping capability of fully worn brakes. (iv) The maximum airplane brake energy allowed for dispatch should not exceed the value for which a satisfactory after-stop condition exists, or the value documented under the applicable Technical Standard Order (TSO) (or an acceptable equivalent), whichever value is less.

A satisfactory after-stop condition is defined as one in which fires are confined to tires, wheels, and brakes, such that progressive engulfment of the rest of the airplane would not occur during the time of passenger and crew evacuation. The application of fire fighting means or artificial coolants should not be required for a period of 5 minutes following the stop. (v) Landings are not an acceptable means for demonstrating the maximum rejected takeoff brake energy. Though permitted in the past, service experience has shown that methods used to predict brake and tire temperature increases that would have occurred during taxi and acceleration, as specified in paragraph 11(c)(2)(i), were not able to accurately account for the associated energy increments. (3) Accelerate-Stop Time Delays. Section 25.101(h) of the FAR requires allowance for time delays in the execution of procedures. Amendment 25-42 (effective March 1, 1978) amended the airworthiness standards to clarify and standardize the method of applying these time delays to the accelerate-stop transition period.

Amendment 25-42 also added the critical engine failure speed, VEF, and clarified the meaning of V1 with relation to VEF. The preamble to Amendment 25-42 states that “V1 is determined by adding to VEF (the speed at which the critical engine is assumed to fail) the speed gained with the critical engine inoperative during the time interval between the instant at which the critical engine is failed and the instant at which the test pilot recognizes and reacts to the engine failure, as indicated by the pilot’s application of the first retarding means during accelerate-stop tests. Thus it can be seen that V1 is not only intended to be at the end of the decision process, but it also includes the time it takes for the pilot to perform the first action to stop the airplane. The purpose of the time delays is to allow sufficient time (and distance) for a pilot, in actual operations, to accomplish the procedures for stopping the airplane. The time delays are not intended to allow extra time for making a decision to stop as the airplane passes through V1.

Since the typical transport category airplane requires three pilot actions (i.e., brakes-throttles-spoilers) to achieve the final braking configuration, Amendment 25- 42 defined a two-second time period, in § 25.109, to account for delays in activating the second and third deceleration devices. Amendment 25-92 (effective March 20, 1998) redefined, and reinterpreted the application of that two-second delay time as a distance increment equivalent to two seconds at V1. No credit may be taken for system transient effects (e.g., engine spin-down, brake pressure ramp-up, etc.) in determining this distance. The following paragraphs provide guidance related to the interpretation and application of delay times to show compliance with the accelerate-stop requirements of Amendment 25-92.

80-6 Chap 2

6/3/99 AC 25-7A Chg. 1

(i) Figure 11-1 presents a pictorial representation of the accelerate-stop time delays considered acceptable for compliance with § 25.101(h) as discussed above. FIGURE 11-1. ACCELERATE-STOP TIME DELAYS

Initiation of

first pilot

action

Initiation of second pilot

action

Initiation of

third pilot

action Engine failure

V1 VEF

tact 1

tact 1

Event

Demonstrated Time Delays

Flight Manual Expansion Time Delays

Initiation of subsequent pilot actions

tact 4 n

tact+ 1 sec.

tact 2

tact 2

tact 3

tact 3

Distance equivalent

to 2 sec. at V1 (ii) VEF is the calibrated airspeed selected by the applicant at which the critical engine is assumed to fail. The relationship between VEF and V1 is defined in § 25.107. (iii) ∆tact 1 = the demonstrated time interval between engine failure and initiation of the first pilot action to stop the airplane. This time interval is defined as beginning at the instant the critical engine is failed and ending when the pilot recognizes and reacts to the engine failure, as indicated by the pilot’s application of the first retarding means during accelerate-stop tests. A sufficient number of demonstrations should be conducted using both applicant and FAA test pilots to assure that the time increment is representative and repeatable. The pilot’s feet should be on the rudder pedals, not the brakes, during the tests. For AFM data expansion purposes, in order to provide a recognition time increment that can be executed consistently in service, this time increment must be equal to the demonstrated time or one second, whichever is greater.

If the airplane incorporates an engine failure warning light, the recognition time includes the time increment necessary for the engine to spool down to the point of warning light activation, plus the time increment from light “on” to pilot action indicating recognition of the engine failure. (iv) ∆tact 2 = the demonstrated time interval between initiation of the first and second pilot actions to stop the airplane. (v) ∆tact 3 = the demonstrated time interval between initiation of the second and third pilot actions to stop the airplane. (vi) ∆tact 4→n = the demonstrated time interval between initiation of the third and fourth (and any subsequent) pilot actions to stop the airplane. For AFM expansion, a one-second reaction time delay to account for in-service variations should be added to the demonstrated time interval between the third and fourth (and any subsequent) pilot actions. If a command is required for another crewmember to initiate an action to stop the airplane, a two-second delay, in

Chap 2 80-7

AC 25-7A 6/3/99 Chg. 1

lieu of the one-second delay, should be applied for each action. For automatic deceleration devices that are approved for performance credit for AFM data expansion, established systems actuation times determined during certification testing may be used without the application of the additional time delays required by this paragraph. (vii) The sequence for initiation of pilot actions may be selected by the applicant, but it must match the sequence established for operation in service, as prescribed by § 25.101(f). If, on occasion, the specified sequence is not achieved during testing, the test need not be repeated; however, sufficient testing must be conducted to establish acceptable values of ∆tact. (viii) Sections 25.109(a)(1)(iv) and (a)(2)(iii) require the one-engine-inoperative and all-engines-operating accelerate-stop distances, respectively, to include a distance increment equivalent to two seconds at V1.

(Although the requirement for the distance increment equivalent to two seconds at V1 is explicitly stated in the “dry runway” criteria of § 25.109, it is also applied to the “wet runway” accelerate-stop distances by reference in § 25.109(b). This distance increment is represented pictorially on the right side of the “Flight Manual Expansion Time Delays” presentation in Figure 11-1, and in the speed versus distance plot of Figure 11-2, on the following page. The two-second time period is only provided as a method to calculate the required distance increment, and is not considered to be a part of the accelerate-stop braking transition sequence. Consequently, no credit for pilot actions, or engine and systems transient responses (e.g., engine spin-down) may be taken during this two-second time period. Similarly, the two-second time period may not be reduced for airplanes incorporating automated systems that decrease the number of pilot actions required to obtain the full braking configuration (e.g., autospoiler systems).

80-8 Chap 2

6/3/99 AC 25-7A Chg. 1

FIGURE 11-2. ACCELERATE-STOP SPEED VS. DISTANCE

3rd Action 2nd Action V1 (1st Action)

VEF

AFM model must accurately represent demonstrated energy state of the airplane after V1.

}

Distance for 2 secs. at V1

SPEED

DISTANCE

(ix) Any residual acceleration that occurs after V1, while the airplane and its systems become stabilized in the braking configuration, must be accounted for in the expansion of accelerate-stop performance data for presentation in the AFM. The effects of system transients, such as engine spin-down, brake pressure ramp-up, spoiler actuation times, etc., should be accounted for in this time period. The area of interest is noted at the top of the graphical representation of the speed versus distance relationship in Figure 11-2. (x) All-Engine Accelerate-Stop Distance. For the all-engines-operating acce stop distance prescribed by § 25.109(a)(2), apply the demonstrated time intervals, and ass delays, of paragraphs 11c(3)(iv) through (vi) after the airplane has accelerated to V

lerateociated

1. (xi) The procedures used to determine the accelerate-stop distance must be described in the performance section of the AFM.

Chap 2 80-9

AC 25-7A 6/3/99 Chg. 1

(4) Wet Runway Accelerate-Stop Distance. The following guidance is provided for showing compliance with the requirements stated in §§ 25.109(b) through (d) for determinin accelerate-stop distances applicable to wet runways. In general, the wet runway accelerate-stop distance is determined in a similar manner to the dry runway accelerate-stop distance. The only differences are in reflecting the reduced stopping force available from the wheel brakes on the wet surface and in provisions for performance credit for the use of reverse thrust as an a decelerating means. The general method for determining the reduced stopping capability of the wheel brakes on a smooth wet runway is as follows: First, determine the maximum tire-to-gro

g

dditional

und et runway braking coefficient of friction versus ground speed from the relationships provided in

the

e

topping force used to determine the dry runway accelerate-stop distance (under § 25.109(a)).

rce g the method st described.

w § 25.109(c)(1). Then, adjust this braking coefficient to take into account the efficiency of anti-skid system. (See paragraph 11c(4)(ii) for a definition of anti-skid efficiency. Next, determine the resulting braking force and adjust this force for the effect of the distribution of th normal load between braked and unbraked wheels at the most adverse center-of-gravity position approved for takeoff, as prescribed by § 25.109(b)(2)(ii). In accordance with § 25.109(b)(2)(i), apply further adjustments, if necessary, to ensure that the resulting stopping force attributed to the wheel brakes on a wet runway never exceeds (i.e., during the entire stop) the wheel brakes s Neither the dry runway brake torque limit nor the dry runway friction (i.e., anti-skid) limit should be exceeded. Alternative methods of determining the wet runway wheel brakes stopping fo may be acceptable as long as that force does not exceed the force determined usin ju (i) Maximum Tire-to-Ground Braking Coefficient of Friction.

The values specified in § 25.109(c)(1) were derived from data contained in Engineering Sciences Data Unit (ESDU) 71026, “Frictional and Retarding Forces on Aircraft Types - Part II: Estimation of Braking Force,” (August 1981). The data in ESDU 71026 is a compilation from many different sources, including the National Aeronautics and Space Administration, the British Ministry of Aviation, and others. ESDU 71026 contains curves of wet runway braking coefficients versus speed for smooth and treaded tires at varying inflation pressures. These data are presented for runways of various surface roughness, including grooved and porous friction course runw Included in the data presentation are bands about each of the curves, which represent variations

ays.

: water depths from damp to flooded, runway surface texture within the defined texture levels,

d curves of wet runway raking coefficient versus speed that are prescribed by the equations in § 25.109(c)(1), the effects

in tire characteristics, and experimental methods. In defining the standar b of the following variables were considered: tire pressure, tire tread depth, runway surface texture, and the depth of the water on the runway. (A) Tire Pressure: Lower tire pressures tend to improve the airplane’s stopping capability on a wet runway. The effect of tire pressure is taken into account by providing separate curves (equations) in § 25.109(c)(1) for several tire pressures. As stated in the rule, the tire pressure used to determine the maximum tir

e-to-ground braking coefficient of iction must be the maximum tire pressure approved for operation. Linear interpolation may be fr used for tire pressures other than those listed.

80-10 Chap 2

6/3/99 AC 25-7A Chg. 1

(B) Tire Tread Depth: The degree to which water can be channeled out from under the tires significantly affects wet runway stopping capability. The standard curves of braking coefficient versus speed prescribed in § 25.109(c)(1) are based on a tire tread depth of 2 mm. Th

is tread depth is consistent with tire removal and retread practices reported by airplane nd tire manufacturers and tire retreaders. It is also consistent with FAA guidance provided in

ot

a AC 121.195(d)-1A, regarding the tread depth for tires used in flight tests to determine operational landing distances on wet runways. Although operation with zero tread depth is n prohibited, it is unlikely that all of the tires on an airplane would be worn to the same extent. (C) Runway Surface Texture: ESDU 71026 groups runways into five categories. These categories are labeled “A” through “E,” with “A” being the smoothest and “C” the most heavily textured ungrooved runways. Categories “D” and “E” represent grooved and

ther open textured surfaces. Category A represents a very smooth texture (an average texture

gory o depth of less than 0.004 inches), and is not very prevalent in runways used by transport cate airplanes. The majority of ungrooved runways fall into the category C grouping. The curves represented in § 25.109(c)(1) represent a texture midway between categories B and C. (D) Depth of Water on the Runway: Obviously, the greater the water depth, the greater the degradation in braking capability. The curves prescribed in § 25.109(c)(1)

present a well-soaked runway, but with no significant areas of standing water. re (ii) Anti-Skid System Efficiency. Section 25.109(c)(2) requires adjusting the maximum tire-to-ground braking coefficient determined in § 25.109(c)(1) to take into acco the efficiency of the anti-skid system. The anti-skid system efficiency i

unt s defined as the relative apability of the anti-skid system to obtain the maximum friction available between the tire and

at es

less g must

s.

c the runway surface (µmax). It is expressed as either a percentage of µmax or a factor based on th percentage (e.g., 85% or 0.85). Applicants can either use one of the anti-skid efficiency valu specified in § 25.109(c)(2), or derive the efficiency from flight tests on a wet runway. Regard of which method is used, § 25.109(c)(2) requires that an appropriate level of flight testin be performed to verify that the anti-skid system operates in a manner consistent with the efficiency value used, and that the system has been properly tuned for operation on wet runway (A) Classification of Types of Anti-Skid Systems. (1) The efficiency values specified in § 25.109(c)(2) are a function of the type of anti-skid system installed on the airplane. Three broad system types are identified in the

le: on/off, quasi-modulating, and fully modulating. These classifications represent evolving levels of technology and differing performance capabilities on dry and wet runways. The classification of anti-skid system types and the assigned efficiency values are based on information contained in Society of Automotive Engineers (SAE) Aerospace Information Report (AIR) 1739, titled “Information on Anti-Skid Systems.” (2

ru

) On/off systems are the simplest of the three types of anti-skid systems. For these systems, full-metered brake pressure (as commanded by the pilot) is applied until wheel locking is sensed. Brake pressure is then released to allow the wheel to spin back up.

Chap 2 80-11

AC 25-7A 6/3/99 Chg. 1

When the system senses that the wheel is accelerating back to synchronous speed (i.e., ground speed), ful te pressure release is repeated throughout the stop (or until the wheel ceases to skid with pressure applied). (3

l-metered pressure is again applied. The cycle of full pressure application/comple

) Quasi-modulating systems attempt to continuously regulate brake pressure as a function of wheel speed. Typically, brake pressure is released when the wheel deceleration rate exceeds a preselected value. Brake pressure is re-applied at a lower level after a length of time appropriate to the depth of the skid. Brake pressure is then gradually increased until another incipient skid condition is sensed. In general, the corrective actions taken by these systems to exit the skid condition are based on a pre-programmed sequence rather than the wheel speed time history. (4) Fully modulating systems are a further refinement of the quasimodulating systems. The major difference between these two types of anti-skid systems is in the implementation of the skid control logic. During a skid, corrective action is based on the sensed wheel speed signal, rather than a pre-programmed response. Specifically, the amount of pressure reduction or reapplication is based on the rate at which the wheel is going into or recovering from a skid. (5) In addition to examining the control system for the differences noted above, a time history of the response characteristi s of the anti-skid system during a wet runway

op should be used to help identify the type of anti-skid system. Comparing the response

c st characteristics between wet and dry runway stops can also be helpful. (6) Figure 11-3 shows an example of the response characteristics typical on-off system on both dry and wet runways. In general, the on-off system exhibits a cyclic behavior of brake pressure application until a skid is sensed, followed by the complete release of brake pressure to allow the wheel to spin back up. Full-metered pressure (as commanded by the pilot) is then re-applied, starting the cycle over again. The wheel speed trace exhibits deep and frequent skids (the troughs in the wheel speed trace), and the average wheel speed is significantly less than the synchronous speed (which is represented by the flat-topped portions of the wheel speed trace). Note that the skids are deeper and more frequent on a wet runway than on a dry runway. For the particular example shown in Figure 11-3, the brake becomes torque-limited toward the

of a

end of the dry runway stop, and is unable to generate enough rque to cause further skidding. to

80-12 Chap 2

6/3/99 AC 25-7A Chg. 1

FIGURE 11-3. ANTI-S CHARACTERISTICS KID SYSTEM RESPONSE On-Off System

(7) The effectiveness of quasi-modulating systems can vary significantly depending on the slipperiness of the runway and the design of the particular control system. On dry runways, these systems typically perform very well; however, on wet runways their performance is highly dependent on the design and tuning of the particular system. An example of the response characteristics of one such system is shown in Figure 11-4. On both dry and wet runways, brake pressure is released to the extent necessary to control skidding. As the wheel

turns to the synchronous speed, brake pressure is quickly increased to a pre-determined level re

Chap 2 80-13

AC 25-7A 6/3/99 Chg. 1

Continue reading ↓ 120 of 1025 passages shown