AC 150/5390-2C Heliport Design
Provides standards for the design of heliports serving helicopters with single rotors. Basic concepts can also be applied to facilities serving helicopters with tandem (front and rear) or dual (side by side) rotors; although many standards will not apply to these facilities. This version adds guidance for pavement or structure larger than the touchdown and liftoff area (TLOF), but less than the size of the final approach and take off (FATO); turbulence effects; clearance between parking areas and taxi routes and within parking areas; minimum dimensions of curved approach/departure airspace; Touchdown/Positioning Circle (TDPC) Marking; Flight Path Alignment Guidance markings and lights; Emergency Helicopter Landing Facility Requirements (EHLF); FATO to FATO separation distance for simultaneous operations; revised standards for size of “H” for general aviation heliports; increased TLOF size when the FATO of a hospital heliport is not load bearing; and Heliport Protection Zone (HPZ) for hospital heliports. See "Principal Changes" for a complete list.
This document is no longer current. Cancelled by 150/5390-2D. Check the official source before relying on it.
Department of Transportation logoAdvisory U.S. Department of Transportation Circular Federal Aviation Administration
Subject: Heliport Design Date: 4/24/2012 AC No: 150/5390-2C Initiated by: AAS-100 Change:
1. Purpose. This advisory circular (AC) provides standards for the design of heliports serving helicopters with single rotors. Apply basic concepts to facilities serving helicopters with tandem (front and rear) or dual (side by side) rotors, however many standards will not apply.
2. Cancellation. This AC cancels AC 150/5390-2B, Heliport Design, dated September 30, 2004.
3. Application. The Federal Aviation Administration (FAA) recommends the guidelines and specifications in this AC for materials and methods used in the construction of heliports. In general, use of this AC is not mandatory. However, use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and with revenue from the Passenger Facility Charge (PFC). See Grant Assurance No. 34, Policies, Standards, and Specifications, and PFC Assurance No. 9, Standards and Specifications. For information about grant assurances, see http://www.faa.gov/airports/aip/grant_assurances/. The use of terms implying strict compliance applies only to those projects. Other federal agencies, states, or other authorities having jurisdiction over the construction of other heliports decide the extent to which these standards apply.
4. Principal changes.
a. Changed the term for the helicopter overall length (OL) to ‘D’ or ‘D-value.’
b. Added definitions for design loads for static and dynamic load-bearing areas (LBA).
c. Added guidance for pavement or structure larger than the touchdown and liftoff area (TLOF), but less than the size of the final approach and take off (FATO).
d. Added guidance for turbulence effects.
e. Added guidance to provide adequate clearance between parking areas and taxi routes and within parking areas.
f. Added guidance for minimum dimensions of curved approach/departure airspace.
g. Added guidance for Touchdown/Positioning Circle (TDPC) Marking.
h. Added guidance for Flight Path Alignment Guidance markings and lights.
i. Added an appendix providing guidance for Emergency Helicopter Landing Facility Requirements (EHLF).
j. Added FATO to FATO separation distance for simultaneous operations.
k. Revised standards for size of “H” for general aviation heliports.
l. Added increased TLOF size when the FATO of a hospital heliport is not load bearing.
n. Combined chapter 6, Non-Precision Instrument Operations and Chapter 7, Precision Approach Operations into chapter 6, Instrument Operations. Reference FAA Order 8620 series.
o. To improve the legibility of the AC, changed the format to a single column and nested the tables in the text.
p. Deleted requirements for load bearing capacity of a FATO at general aviation and hospital heliports when the TLOF is marked.
q. Changed color of landing direction lights from yellow to green.
r. Added references to Engineering Brief 87, Heliport Lights for Visual Meteorological Conditions (VMC).
5. Use of metrics. This AC includes both English and metric dimensions. The metric conversions may not be exact equivalents, and the English dimensions govern.
6. Copies of this AC. This and other advisory circulars published by the Office of Airport Safety and Standards are available on the FAA Office of Airports web page at www.faa.gov/airports. Signature of Michael J. O'DonnellMICHAEL J. O’DONNELL
Director of Airport Safety and Standards
ii
TABLE OF CONTENTS
Paragraph Page
Chapter 1. Introduction … 1
101. Background … 1 102. General … 1 103. Facilities … 1 104. Planning … 1 105. Existing heliports … 1 106. Location … 1 107. AC organization … 2 108. Explanation of terms … 2 109. Selection of approach/departure paths … 6 110. Notification requirements … 6 111. Hazards to air navigation … 9 112. Federal assistance … 10 113. Environmental impact analyses … 10 114. Access to heliports by individuals with disabilities … 11 115. State role … 11 116. Local role … 11 117. Related referenced material … 11
Chapter 2. General Aviation Heliports … 13
201. General … 13 202. Applicability … 13 203. Prior permission required (PPR) facilities … 14 204. Access by individuals with disabilities … 14 205. Heliport site selection … 14 206. Basic layout … 14 207. Touchdown and liftoff area (TLOF) … 15 208. Final approach and takeoff area (FATO) … 20 209. Safety area … 22 210. VFR approach/departure paths … 22 211. Heliport protection zone (HPZ) … 29 212. Wind cone … 29 213. Taxiways and taxi routes … 29 214. Helicopter parking … 35 215. Heliport markers and markings … 44 216. Heliport lighting … 53 217. Marking and lighting of difficult-to-see objects … 58 218. Safety considerations … 61 219. Visual glideslope indicators (VGSI) … 64 220. Terminal facilities … 64 221. Zoning and compatible land use … 64
iii
Chapter 3. Transport Heliports … 65
301. General … 65 302. Applicability … 65 303. Access by individuals with disabilities … 65 304. Heliport site selection … 65 305. Basic layout … 67 306. Touchdown and liftoff area (TLOF) … 67 307. Final approach and takeoff area (FATO) … 71 308. Safety area … 72 309. VFR approach/departure paths … 73 310. Heliport protection zone (HPZ) … 76 311. Wind cone … 76 312. Taxiways and taxi routes … 77 313. Helicopter parking … 77 314. Heliport markers and markings … 88 315. Heliport lighting … 93 316. Marking and lighting of difficult-to-see objects … 100 317. Safety considerations … 103 318. Visual glideslope indicators (VGSI) … 105 319. Terminal facilities … 107 320. Zoning and compatible land use … 107
Chapter 4. Hospital Heliports … 109
401. General … 109 402. Applicability … 109 403. Access by individuals with disabilities … 109 404. Heliport site selection … 109 405. Basic layout … 112 406. Touchdown and liftoff area (TLOF) … 112 407. Final approach and takeoff area (FATO) … 114 408. Safety area … 116 409. VFR approach/departure paths … 118 410. Heliport protection zone (HPZ) … 123 411. Wind cone … 123 412. Taxiways and taxi routes … 126 413. Helicopter parking … 130 414. Heliport markers and markings … 138 415. Heliport lighting … 147 416. Marking and lighting of difficult-to-see objects … 154 417. Safety considerations … 157 418. Visual glideslope indicators (VGSI) … 159 419. Zoning and compatible land use … 159
Chapter 5. Helicopter Facilities on Airports … 161
501. General … 161
iv
LIST OF FIGURES
502. Applicability … 161 503. Touchdown and liftoff area (TLOF) … 161 504. Final approach and takeoff area (FATO) … 161 505. Safety area … 161 506. VFR approach/departure paths … 161 507. Heliport protection zone (HPZ) … 162 508. Taxiways and taxi routes … 162 509. Helicopter parking … 162 510. Security … 162
Chapter 6. Instrument Operations … 165
601. General … 165 602. Planning … 165 603. Airspace … 165 604. Final approach reference area (FARA) … 165 605. Improved lighting system … 165 606. Obstacle evaluation surfaces … 166
Chapter 7. Heliport Gradients and Pavement Design … 169
701. General … 169 702. TLOF gradients … 169 703. FATO gradients … 169 704. Safety area gradients … 169 705. Parking area gradients … 169 706. Taxiway and taxi route gradients … 169 707. Design loads … 171 708. Pavement design and soil stabilization … 171
Appendix A. Emergency Helicopter Landing Facilities (EHLF) … 175
Appendix B. Helicopter Data … 179
Appendix C. Dimensions for Marking Size and Weight Limitations … 185
Appendix D. Associated Publications and Resources … 187
LIST OF FIGURES
Figure 1–1. Form 7480-1, Notice of Landing Area Proposal … 7 Figure 1–2. Example of a Heliport Layout Plan … 8 Figure 1–3. Example of a Heliport Location Map … 10 Figure 1–4. Offsite Development Requiring Notice to the FAA … 12 Figure 2–1. Essential Features of a Heliport: General Aviation … 13
v
Figure 2–2. TLOF/FATO Safety Area Relationships and Minimum Dimensions: General Aviation … 16 Figure 2–3. Elongated FATO with Two Takeoff Positions: General Aviation … 17 Figure 2–4. Elevated Heliport: General Aviation … 19 Figure 2–5. Additional FATO Length for Heliports at Higher Elevations: General Aviation … 21 Figure 2–6. Non-load-bearing FATO and Safety Area: General Aviation … 23 Figure 2–7. VFR Heliport Approach/Departure and Transitional Surfaces: General Aviation … 25 Figure 2–8. Curved Approach/Departure: General Aviation … 26 Figure 2–9. VFR PPR Heliport Lateral Extension of the 8:1 Approach / Departure Surface: General
Aviation … 27 Figure 2–10. VFR PPR Heliport Lateral Extension of the Curved 8:1 Approach / Departure Surface:
Figure 1-1 · page 5Picture of the page from the copy saved here
General Aviation … 28 Figure 2–11. Flight Path Alignment Marking and Lights: General Aviation … 30 Figure 2–12. Heliport Protection Zone: General Aviation … 31 Figure 2–13. Taxiway/Taxi Route Relationship – Paved Taxiway: General Aviation … 32 Figure 2–14. Taxiway/Taxi Route Relationship – Unpaved Taxiway with Raised Edge Markers: General
Aviation … 33 Figure 2–15. Taxiway/Taxi Route Relationship – Unpaved Taxiway with Flush Edge Markers: General
Figure 2-11 · page 6Picture of the page from the copy saved here
Aviation … 34 Figure 2–16. Parking Area Design – “Taxi-through” Parking Positions: General Aviation … 37 Figure 2–17. Parking Area Design – “Turn-around” Parking Positions: General Aviation … 38 Figure 2–18. Parking Area Design – “Back-out” Parking Positions: General Aviation … 39 Figure 2–19. “Turn-around” Parking Position Marking: General Aviation … 40 Figure 2–20. “Taxi-through” and “Back-out” Parking Position Marking: General Aviation … 41 Figure 2–21. Parking Position Identification, Size, and Weight Limitations: General Aviation … 43 Figure 2–22. Standard and Alternate TLOF Marking: General Aviation … 46 Figure 2–23. Standard Heliport Identification Symbol, TLOF Size and Weight Limitations: General
Figure 2-16 · page 6Picture of the page from the copy saved here
Aviation … 47 Figure 2–24. Extended Pavement / Structure Marking: General Aviation … 48 Figure 2–25. Paved TLOF/Paved FATO – Paved TLOF/ Unpaved FATO – Marking: General Aviation 49 Figure 2–26. Unpaved TLOF/Unpaved FATO – Marking: General Aviation … 50 Figure 2–27. Marking a Closed Heliport: General Aviation … 52 Figure 2–28. Elevated TLOF – Perimeter Lighting: General Aviation … 53 Figure 2–29. TLOF/FATO Flush Perimeter Lighting: General Aviation … 55 Figure 2–30. TLOF Flush and FATO Raised Perimeter Lighting: General Aviation … 56 Figure 2–31. Landing Direction Lights: General Aviation … 57 Figure 2–32. Airspace Where Marking and Lighting are Recommended: Straight Approach: General
Aviation … 59 Figure 2–33. Airspace Where Marking and Lighting are Recommended: Curved Approach: General
Figure 2-24 · page 6Picture of the page from the copy saved here
Aviation … 60 Figure 2–34. Caution Sign: General Aviation … 62 Figure 2–35. Visual Glideslope Indicator Siting and Clearance Criteria: General Aviation … 63 Figure 3–1. Typical Transport Heliport: Transport … 66 Figure 3–2. TLOF/FATO Safety Area Relationships and Minimum Dimensions: Transport … 68 Figure 3–3. Elongated FATO with Two Takeoff Positions: Transport … 69 Figure 3–4. Elevated Heliport: Transport … 70 Figure 3–5. Additional FATO Length for Heliports at Higher Elevations: Transport … 71 Figure 3–6. Non-load-bearing Safety Area: Transport … 74 Figure 3–7. VFR Heliport Approach/Departure and Transitional Surfaces: Transport … 75
vi
Figure 3–8. Curved Approach/Departure: Transport … 78
Figure 3–25. Airspace Where Marking and Lighting are Recommended: Straight Approach: Transport101
Figure 4–13. Taxiway/Taxi Route Relationship – Unpaved Taxiway with Raised Edge Markers: Hospital
Figure 2-34 · page 6Picture of the page from the copy saved here
Figure 3–9. Flight Path Alignment Marking and Lights: Transport … 79 Figure 3–10. Heliport Protection Zone: Transport … 80 Figure 3–11. Taxiway/Taxi Route Relationship, Centerline and Edge Marking: Transport … 81 Figure 3–12. “Turn-around” Helicopter Parking Position Marking: Transport … 82 Figure 3–13. “Taxi-through” Helicopter Parking Position Marking: Transport … 83 Figure 3–14. Parking Area Design – “Turn-around” Parking Positions: Transport … 85 Figure 3–15. Parking Area Design – “Taxi-through” Parking Position … 86 Figure 3–16. Parking Position Identification, Size and Weight Limitations: Transport … 87 Figure 3–17. Standard Heliport Identification Symbol, TLOF Size and Weight Limitations: Transport ..89 Figure 3–18. Paved TLOF/Paved FATO – Paved TLOF/Unpaved FATO – Marking: Transport … 90 Figure 3–19. Marking a Closed Heliport: Transport … 93 Figure 3–20. TLOF and FATO Flush Perimeter Lighting: Transport … 94 Figure 3–21. FATO Raised and TLOF Flush Perimeter Lighting: Transport … 95 Figure 3–22. Optional TLOF Lights: Transport … 97 Figure 3–23. Elevated FATO – Perimeter Lighting: Transport … 98 Figure 3–24. Landing Direction Lights: Transport … 99
Figure 3-9 · page 7Picture of the page from the copy saved here
Figure 3–26. Airspace Where Marking and Lighting are Recommended: Curved Approach: Transport 102 Figure 3–27. Caution Sign: Transport … 104 Figure 3–28. Visual Glideslope Indicator Siting and Clearance Criteria: Transport … 106 Figure 4–1. Essential Features of a Ground-level Hospital Heliport: Hospital … 110 Figure 4–2. TLOF/FATO Safety Area Relationships and Minimum Dimension: Hospital … 111 Figure 4–3. Elongated FATO with Two Takeoff Positions: Hospital … 113 Figure 4–4. Additional FATO Length for Heliports at Higher Elevation: Hospital … 115 Figure 4–5. Rooftop Hospital Heliport: Hospital … 117 Figure 4–6. VFR Heliport Approach/Departure and Transitional Surfaces: Hospital … 119 Figure 4–7. Curved Approach/Departure: Hospital … 120 Figure 4–8. VFR Heliport Lateral Extension of the 8:1 Approach / Departure Surface: Hospital … 121 Figure 4–9. VFR Heliport Lateral Extension of the Curved 8:1 Approach/Departure Surface: Hospital 122 Figure 4–10. Flight Path Alignment Marking and Lights: Hospital … 124 Figure 4–11. Heliport Protection Zone: Hospital … 125 Figure 4–12. Taxiway/Taxi Route Relationship – Paved Taxiway: Hospital … 127
Figure 3-26 · page 7Picture of the page from the copy saved here
… 128 Figure 4–14. Taxiway/Route Relationship – Unpaved Taxiway with Flush Edge Markers: Hospital … 129 Figure 4–15. Parking Area Design – “Taxi-through” Parking Positions: Hospital … 132 Figure 4–16. Parking Area Design – “Turn-around” Parking Positions: Hospital … 133 Figure 4–17. Parking Area Design – “Back-out” Parking Positions: Hospital … 134 Figure 4–18. “Turn-around” Helicopter Parking Position Marking: Hospital … 135 Figure 4–19. “Taxi-through” and “Back-out” Helicopter Parking Position Marking: Hospital … 136 Figure 4–20. Parking Position Identification, Size, and Weight Limitations: General Aviation … 137 Figure 4–21. Standard Hospital Heliport Identification Symbols: Hospital … 139 Figure 4–22. Alternative Hospital Heliport Identification Symbols: Hospital … 140 Figure 4–23. Paved TLOF/Paved FATO – Paved TLOF/Unpaved FATO – Marking: Hospital … 141 Figure 4–24. Unpaved TLOF/Unpaved FATO – Marking: Hospital … 142 Figure 4–25. TLOF Size and Weight Limitations: Hospital … 144
vii
Figure 4-14 · page 7Picture of the page from the copy saved here
LIST OF TABLES
Figure 4–26. Extended Pavement or Structure Marking: Hospital … 145 Figure 4–27. Marking a Closed Heliport: Hospital … 147 Figure 4–28. Flush TLOF/FATO Perimeter Lighting: Hospital … 149 Figure 4–29. Elevated TLOF, Safety Net and Lighting Heliport Partial Elevation: Hospital … 150 Figure 4–30. Flush TLOF and Raised FATO Perimeter Lighting: Hospital … 151 Figure 4–31. Landing Direction Lights: Hospital … 153 Figure 4–32. Airspace Where Marking and Lighting are Recommended: Hospital … 155 Figure 4–33. Airspace Where Marking and Lighting are Recommended: Curved Approach: Hospital ..156 Figure 4–34. Caution Sign: Hospital … 158 Figure 4–35. Visual Glideslope Indicator Siting and Clearance Criteria: Hospital … 160 Figure 5–1. Heliport Located on an Airport: On Airport … 163 Figure 6–1. FARA/FATO Relationship: Precision … 166 Figure 6–2. Heliport Instrument Lighting System (HILS): Non-precision … 167 Figure 6–3. Heliport Approach Lighting System … 168 Figure 7–1. Heliport Grades and Rapid Runoff Shoulder: Gradients and Pavement … 170 Figure 7–2. Helicopter Landing Gear Loading: Gradients and Pavement … 172 Figure 7–3. FATO Elevation … 173 Figure A-1. Rooftop Emergency Landing Facility … 177 Figure B–1. Helicopter Dimensions … 184 Figure C–1. Form and Proportions of 36 Inch (91 cm) Numbers for Marking Size and Weight Limitations
Figure 4-26 · page 8Picture of the page from the copy saved here
… 185 Figure C–2. Form and Proportions of 18 Inch (45.7 cm) Numbers for Marking Size and Weight
Limitation … 186
LIST OF TABLES
Table 2-1. Minimum VFR Safety Area Width as a Function of General Aviation and PPR Heliport
Markings … 15 Table 2-2. Taxiway/Taxi Route Dimensions – General Aviation Heliports … 36 Table 3-1. Taxiway and Taxi Route Dimensions – Transport Heliports … 77 Table 4-1. Minimum VFR Safety Area Width as a Function of Hospital Heliport Markings … 116 Table 4-2. Taxiway / Taxi Route Dimensions – Hospital Heliports … 130 Table 5-1. Recommended Distance between FATO Center to Runway Centerline for VFR Operations 161
viii
Chapter 1. Introduction › 106. Location.
Chapter 1. Introduction
101. Background. Section 103 of the Federal Aviation Act of 1958 states in part, “In the exercise and performance of his power and duties under this Act, the Secretary of Transportation shall consider the following, among other things, as being in the public interest: (a) The regulation of air commerce in such manner as to best promote its development and safety and fulfill the requirements of defense; (b) The promotion, encouragement, and development of civil aeronautics . . .” This public charge, in effect, requires the development and maintenance of a national system of safe heliports. Using the standards and recommendations contained in this publication in the design of heliports supports this public charge. These standards and recommendations, however, do not limit or regulate the operations of aircraft. When it is not feasible to meet all the standards and recommendations in this AC, consult with the appropriate offices of the Federal Aviation Administration (FAA) Office of Airports and Flight Standards Service to identify any adjustments to operational procedures necessary to accommodate operations to the maximum extent.
102. General. This chapter provides an explanation of terms used in this AC, describes the notification responsibilities of heliport proponents to FAA, provides general siting guidance, and identifies sources of technical information relating to heliport planning and design of a civil heliport.
103. Facilities. While heliports can be large and elaborate, most are not. The basic elements of a heliport are clear approach/departure paths, a clear area for ground maneuvers, final approach and takeoff area (FATO), touchdown and liftoff area (TLOF), safety area, and a wind cone. This minimal facility may be adequate as a private use prior permission required (PPR) heliport, and may even suffice as the initial phase in the development of a public use heliport capable of serving the general aviation segment of the helicopter community.
104. Planning. While the heliport itself may be simple, the planning and organization required to properly put one into place can be intimidating. Consider the physical, technical, and public interest matters described in this document in the planning and establishment of a heliport. While this AC is a technical document intended to help engineers, architects, and city planners design, locate, and build the most effective heliport, anyone considering the construction of a heliport can use it. Figures in this document are general representations and are not to scale.
105. Existing heliports. When a change to an existing heliport requires the submission of FAA Form 7460-1, Notice of Proposed Construction or Alteration, or FAA Form 7480-1, Notice of Landing Area Proposal, bring the heliport up to current standards. It may not, however, be feasible to meet all current standards at existing heliports. In those cases, consult with the appropriate offices of the FAA Office of Airports and Flight Standards Service to identify any adjustments to operational procedures necessary to accommodate operations to the maximum extent.
106. Location. The optimum location for a heliport is near the desired origination and/or destination of the potential users. Industrial, commercial, and business operations in urban locations are demand generators for helicopter services, even though they often compete for the limited ground space available. Heliport sites may be adjacent to a river or a lake, a railroad, a freeway, or a highway, all of which offer the potential for multi-functional land usage. These locations also have the advantage of relatively unobstructed airspace, which can be further protected from unwanted encroachment by properly enacted zoning. As vertical flight transportation becomes more prevalent, requirements for scheduled “airline type” passenger services may necessitate the development of an instrument procedure to permit “allweather” service.
Chapter 1. Introduction › 108. Explanation of terms.
107. AC organization. This AC is structured to provide communities and persons intending to develop a heliport, or become involved in regulating helicopter facilities, with general guidance on heliport requirements. The AC covers general aviation heliports (including PPR), transport heliports, hospital heliports, and emergency landing facilities. It is important for a heliport proponent to be familiar with the terminology used in this specialized field. This chapter defines terms used in the industry and identifies actions common to developing a heliport.
a. General aviation heliports. The term “general aviation” is technically defined as “flights conducted by operators other than Title 14 of the Code of Federal Regulations (CFR) Part 121 or Part 135 certificate holders.”1 However, for the purposes of this AC, “general aviation” refers to all helicopter operations other than scheduled passenger service. Hospital heliports and emergency landing facilities fall under general aviation, but are treated separately in the AC due to their unique requirements. General aviation heliports are normally privately owned although they can be publicly owned. Find design standards for general aviation heliports in Chapter 2.
b. Transport heliports. Transport heliports will provide the community with a full range of vertical flight services including scheduled service by air carriers (airlines) using helicopters. These operations will require a more extensive airside and landside infrastructure with the potential capability to operate in instrument meteorological conditions. Find design standards for transport heliports in Chapter 3.
c. Hospital heliports. Hospital heliports are general aviation heliports that provide a unique public service. They are normally located close to the hospital emergency room or a medical facility. Find design standards for hospital heliports in 4Chapter 4.
d. Helicopter facilities on airports. When there are a significant number of helicopter operations on an airport, consider developing separate facilities specifically for helicopter use. Chapter 5 addresses helicopter facilities on airports.
e. Instrument operations. With the introduction of the global positioning system (GPS), it is now practical for heliports to have instrument approach procedures. Good planning suggests that heliport proponents plan for the eventual development of instrument approaches to their heliports. Consider the recommendations in Chapter 6 in contemplating future instrument operations at a heliport. It is wise to consider these issues during site selection and design.
f. Heliport gradients and pavement design. 4Chapter 7 addresses heliport gradients and pavement design issues.
g. The appendices provide information about emergency helicopter landing facilities, helicopter dimensional data, form and proportions of certain heliport markings, and a list of publications and resources referenced in this AC.
108. Explanation of terms. The Pilot/Controller Glossary of the Aeronautical Information Manual (AIM) defines terms used in the Air Traffic System. Copies of the AIM are available from the FAA web site http://www.faa.gov/atpubs. Other terms used in this publication follow:
a. Air taxi. Used both to refer to on-demand air carriers and as a synonym for “hover taxi.” See hover taxi.
b. Approach/departure path. The flight track helicopters follow when landing at or departing from a heliport. The approach/departure paths may be straight or curved.
1Plane Sense General Aviation Information, U.S. Department of Transportation FAA-H-8083-19A, http://www.faa.gov/library/manuals/aviation/media/faa-h-8083-19A.pdf
c. Design helicopter. A single or composite helicopter that reflects the maximum weight, maximum contact load/minimum contact area, overall length (D), rotor diameter (RD), tail rotor arc radius, undercarriage dimensions, and pilot’s eye height of all helicopters expected to operate at the heliport.
d. D (Formerly “OL”). The overall length of the helicopter, which is the dimension from the tip of the main or forward rotor to the tip of the tail rotor, fin, or other rear-most point of the helicopter. This value is with the rotors at their maximum extension. See Figure B–1. If only the value of the rotor diameter (RD) is known, estimate the value for D using the relationship D = 1.2 RD (or conversely, RD = 0.83 D).
e. Design loads. Design and construct the TLOF and any load-bearing surfaces to support the loads imposed by the design helicopter and any ground support vehicles and equipment.
(1) Static load. For design purposes, the design static load is equal to the helicopter’s maximum takeoff weight applied through the total contact area of the wheels or skids. See paragraph 707.
(2) Dynamic load. For design purposes, assume the dynamic load at 150 percent of the maximum takeoff weight of the design helicopter applied through the main undercarriage on a wheelequipped helicopter or aft contact areas of skid-equipped helicopter. See paragraph 707.
f. Elevated heliport. A heliport located on a rooftop or other elevated structure where the TLOF is at least 30 inches (76 cm) above the surrounding surface (a ground level heliport with the TLOF on a mound is not an elevated heliport).
g. Emergency helicopter landing facility (EHLF). A clear area at ground level or on the roof of a building capable of accommodating helicopters engaged in fire fighting and/or emergency evacuation operations. An EHLF meets the definition of a heliport in this AC and under Title 14 CFR Part 157, Notice of Construction, Alteration, Activation, and Deactivation of Airports.
h. Final approach and takeoff area (FATO). A defined area over which the pilot completes the final phase of the approach to a hover or a landing and from which the pilot initiates takeoff. The FATO elevation is the lowest elevation of the edge of the TLOF. See Figure 7–3.
i. Final approach reference area (FARA). An obstacle-free area with its center aligned on the final approach course. It is located at the end of a precision instrument FATO.
j. Flush lights. Where the term “flush lights” is specified in this AC, interpret it as including semi-flush lights.
k. Frangible/frangibly mounted. While there is no accepted standard for frangibility in regard to helicopter operations, remove all objects from a FATO or safety area except those of the lowest mass practicable and frangibly mounted to the extent practicable.
Figure 7-3 · page 8Picture of the page from the copy saved here
l. General aviation heliport. A heliport intended to accommodate individuals, corporations, helicopter air taxi operators, and public safety agencies. For the purposes of this AC, “general aviation” refers to all helicopter operations other than scheduled passenger service. Hospital heliports and emergency landing facilities fall under general aviation, but are treated separately in the AC due to their unique requirements.
m. Ground taxi. The surface movement of a wheeled helicopter under its own power with wheels touching the ground.
n. Hazard to air navigation. Any object having a substantial adverse effect upon the safe and efficient use of the navigable airspace by aircraft, upon the operation of air navigation facilities, or upon existing or planned airport/heliport capacity as determined by the FAA.
o. Heliport. The area of land, water, or a structure used or intended to be used for the landing and takeoff of helicopters, together with appurtenant buildings and facilities.
p. Heliport elevation. The highest point of the TLOF expressed as the distance above mean sea level.
q. Heliport imaginary surfaces. The imaginary planes defined in Title 14 CFR Part 77, Safe, Efficient Use, and Preservation of the Navigable Airspace, centered about the FATO and the approach/departure paths, which are used to identify the objects where notice to and evaluation by the FAA is required. Recommendations may include realignment of approach/departure paths or removal, lowering, marking and lighting of objects.
r. Heliport layout plan. The plan of a heliport showing the layout of existing and proposed heliport facilities including the approach/departure paths.
s. Heliport protection zone (HPZ). An area off the end of the FATO and under the approach/departure path intended to enhance the protection of people and property on the ground.
t. Heliport reference point (HRP). The geographic position of the heliport expressed as the latitude and longitude at:
(1) The center of the FATO, or the centroid of multiple FATOs, for heliports having visual and non-precision instrument approach procedures; or
(2) The center of the FARA when the heliport has a precision instrument procedure.
u. Helistop. A term sometimes used to describe a minimally developed heliport for boarding and discharging passengers or cargo. This AC does not use this term, as the design standards and recommendations this AC apply to all heliports.
v. Hospital heliport. A heliport limited to serving helicopters engaged in air ambulance, or other hospital related functions. A designated helicopter landing area located at a hospital or medical facility is a heliport and not a medical emergency site.
w. Hover taxi (also called air taxi). The movement of a wheeled or skid-equipped helicopter above the surface. Generally, this takes place at a wheel/skid height of 1 to 5 feet (0.3 to 1.5 m) and at a ground speed of less than 20 knots (37 km/h). For facility design purposes, assume a skid-equipped helicopter to hover-taxi.
x. Landing position. An area, normally located in the center of an elongated TLOF, on which the helicopter lands.
y. Large helicopter. A helicopter with a maximum takeoff weight of more than 12,500 lbs.
z. Load-bearing area (LBA). The portion of the FATO capable of supporting the dynamic load of the design helicopter.
aa. Medical emergency site. An unprepared site at or near the scene of an accident or similar medical emergency on which a helicopter may land to pick up a patient in order to provide emergency medical transport. A medical emergency site is not a heliport as defined in this AC.
bb. Medium helicopter. A helicopter with a maximum takeoff weight of 7,001 to 12,500 lbs.
cc. Obstruction to air navigation. Any fixed or mobile object, including a parked helicopter, of greater height than any of the heights or surfaces presented in subpart C of part 77 (see also paragraph 111 in this AC).
dd. Overall length (D). See D, paragraph 108.d.
ee. Parking pad. The paved center portion of a parking position.
ff. Prior permission required (PPR) heliport. A heliport developed for exclusive use of the owner and persons authorized by the owner and about which the owner and operator ensure all authorized pilots are thoroughly knowledgeable. These features include but are not limited to: approach/departure path characteristics, preferred heading, facility limitations, lighting, obstacles in the area, and size and weight capacity of the facility.
gg. Public use heliport. A heliport available for use by the general public without a requirement for prior approval of the owner or operator.
hh. RD. Rotor Diameter. The length of the main rotor, from tip to tip.
ii. Rotor downwash. The downward movement of air caused by the action of the rotating main rotor blades. When this air strikes the ground or some other surface, it causes a turbulent outflow of air from beneath the helicopter.
jj. Safety area. A defined area on a heliport surrounding the FATO intended to reduce the risk of damage to helicopters accidentally diverging from the FATO.
kk. Shielded obstruction. A proposed or existing obstruction that does not need to be marked or lighted due to its close proximity to another obstruction whose highest point is at the same or higher elevation.
ll. Shoulder line. A marking line perpendicular to a helicopter parking position centerline that is intended to provide the pilot with a visual cue to assist in parking.
mm. Small helicopter. A helicopter with a maximum takeoff weight of 7,000 lbs or less.
nn. Tail rotor arc radius. The distance from the hub of the main rotor to the outermost tip of the tail rotor or the rear-most point of the helicopter tail, whichever is farther.
oo. Takeoff position. An area, normally located on the centerline and at the ends of an elongated TLOF, from which the helicopter takes off. Typically, there are two such positions on an elongated TLOF, one at each end.
pp. Taxi route. An obstruction-free corridor established for the movement of helicopters from one part of a heliport/airport to another. A taxi route includes the taxiway plus the appropriate clearances on both sides.
qq. Taxiway. A marked route between the TLOF and other areas on the heliport. This AC defines two types of helicopter taxiways:
(1) Ground taxiway. A taxiway intended to permit the surface movement of a wheeled helicopter under its own power with wheels on the ground. The minimum dimensions defined for a ground taxiway may not be adequate for hover taxi.
(2) Hover taxiway. A taxiway intended to permit the hover taxiing of a helicopter.
rr. Touchdown and liftoff area (TLOF). A load-bearing, generally paved area, normally centered in the FATO, on which the helicopter lands and/or takes off.
ss. Transport heliport. A heliport intended to accommodate air carrier operators providing scheduled service.
tt. Touchdown/positioning circle (TDPC) marking. A circular marking located in the center of a TLOF or a parking position. When the pilot’s seat is over the TDPC, the whole of the helicopter undercarriage will be within the TLOF or parking position and all parts of the helicopter rotor system will be clear of any obstacle by a safe margin.
Chapter 1. Introduction › 110. Notification requirements.
uu. Unshielded obstruction. A proposed or existing obstruction that may need to be marked or lighted since it is not near another marked and lighted obstruction whose highest point is at the same or higher elevation.
109. Selection of approach/departure paths. Design heliports to the extent practicable for two approach/departure paths. Consider items such as the following in selecting the approach/departure paths:
a. Wind. Well-designed approach/departure paths permit pilots to avoid downwind conditions and minimize crosswind operations. Align the preferred flight approach/departure path, to the extent feasible, with the predominant wind direction. Base other approach/departure paths on the assessment of the prevailing winds or, when this information is not available, separate such flight paths and the preferred flight path by at least 135 degrees. If it is not feasible to provide complete coverage of wind through multiple approach/departure paths, operational limitations may be necessary under certain wind conditions. See paragraph 101.
b. Obstructions. In determining approach/departure paths, take into account the obstructions in the vicinity of the heliport and, in particular, those likely to be a hazard to air navigation. See paragraph 111.
c. Environmental impacts. In environmentally sensitive areas, select the final approach/departure path(s) to minimize any environmental impact, providing it does not decrease flight safety. See paragraph 113.
110. Notification requirements. Part 157 sets requirements for persons proposing to construct, activate, deactivate, or alter a heliport to give advance notice of their intent to the FAA. This includes changing the size or number of FATOs; adding, deleting, or changing an approach or departure route; or changing heliport status. An example of a heliport status change would be a change from private to public use or vice versa. When notification is required, file Form 7480-1 (see Figure 1–1) with the appropriate FAA Airports Regional or District Office at least 90 days before construction, alteration, deactivation, or change in use. See the FAA Airports web site at http://www.faa.gov/airports/ for contact information.
a. Draw the heliport layout plan to scale showing key dimensions, such as the heliport elevation, TLOF size, FATO size, safety area size, distance from safety area perimeter to property edges, and approach/departure paths showing locations of buildings, trees, fences, power lines, obstructions (including elevations), schools, churches, hospitals, residential communities, waste disposal sites, and other significant features as specified on Form 7480-1 and as suggested in Figure 1–2.
b. The preferred type of location map is the 7.5-minute U.S. Geological Survey Quadrangle Map, available from the US Geological Survey at nationalmap.gov. Web-based maps are also acceptable. Show the location of the heliport site and the approach/departure paths on the map. Point out the heliport site on this map with an arrow. Indicate the latitude and longitude of the proposed heliport in North American Datum of 1983 (NAD-83) coordinates. See Figure 1–3.
Figure 1-2 · page 16Picture of the page from the copy saved here
c. The FAA role. The FAA will conduct an aeronautical study of the proposed heliport under part 157. Title 14 CFR Part 157.7, FAA determinations, states: “The FAA will conduct an aeronautical study of an airport proposal and, after consultations with interested persons, as appropriate, issue a determination to the proponent and advise those concerned of the FAA determination. The FAA will consider matters such as the effects the proposed action would have on existing or contemplated traffic patterns of neighboring airports; the effects the proposed action would have on the existing airspace structure and projected programs of the FAA; and the effects that existing or proposed manmade objects (on file with the FAA) and natural objects within the affected area would have on the airport proposal. While determinations consider the effects of the proposed action on the safe and efficient use of airspace by aircraft and the safety of persons and property on the ground, the determinations are only advisory. Except for an objectionable determination, each determination will contain a determination-void date to
facilitate efficient planning of the use of the navigable airspace. A determination does not relieve the proponent of responsibility for compliance with any local law, ordinance or regulation, or state or other federal regulation. Aeronautical studies and determinations will not consider environmental or land use compatibility impacts.” Form 7480-1, Notice of Landing Area ProposalFigure 1–1. Form 7480-1, Notice of Landing Area Proposal
Example of a He
liport Layout Pla
n
Figure 1–2. Example of a Heliport Layout Plan
d. Penalty for failure to provide notice. Persons who fail to give notice are subject to civil penalty under Title 49 United States Code 46301, Civil Penalties, of not more than $25,000 (or $1,100 if the person is an individual or small business concern).
e. Notice exemptions. Paragraph 157.1, Applicability, of part 157 exempts sites meeting one of the conditions below from the requirement to submit notice. These exemptions do not negate a notice or formal approval requirement prescribed by state law or local ordinance. For the purposes of applying the part 157 exemption criteria cited in (2) and (3) below, a landing and associated takeoff is considered to be one operation. Part 157.1 projects are:
(1) [A heliport] subject to conditions of a federal agreement that requires an approved current heliport layout plan to be on file with the FAA, or
(2) [A heliport] at which flight operations will be conducted under visual flight rules (VFR) and which is used or intended to be used for a period of less than 30 consecutive days with no more than 10 operations per day.
Chapter 1. Introduction › 111. Hazards to air navigation.
(3) The intermittent use of a site that is not an established airport, that is used or intended to be used for less than 1 year, and at which flight operations will be conducted only under VFR. For the purpose of this part, “intermittent use of a site” means:
(a) the site is used or is intended to be used for no more than 3 days in any one week and
(b) no more than 10 operations will be conducted in any one day at that site.
111. Hazards to air navigation. Part 77 establishes requirements for notification to the FAA of objects that may affect navigable airspace. It sets standards for determining obstructions to navigable airspace and provides for aeronautical studies of such obstructions to determine their effect on the safe and efficient use of airspace. Part 77 applies only to public airports and heliports, airports operated by a federal agency or the Department of Defense, and private airports and heliports with at least one FAAapproved instrument approach procedure. See Figure 1–4.
a. FAA studies.
Figure 1-4 · page 20Picture of the page from the copy saved here
(1) Part 77. Part 77 defines objects that are obstructions to surfaces. Presume these objects to be hazards unless an FAA study determines otherwise. The FAA conducts aeronautical studies to determine the physical and electromagnetic effect on the use of navigable airspace, air navigational facilities, public airports and heliports, and private airports and heliports with at least one FAA-approved instrument approach procedure. The FAA encourages public agencies to enact zoning ordinances to prevent man-made features from becoming hazards to navigation.
(2) Part 157. While the FAA performs aeronautical studies under part 157 (see paragraph 110.c), such studies do not identify hazards to private facilities that do not have an FAA-approved instrument approach.
b. Mitigation of hazards. You may mitigate the adverse effect of an object presumed or determined to be a hazard by:
(1) Removing the object.
(2) Altering the object, for example, reducing its height.
(3) Marking and/or lighting the object, provided an FAA aeronautical study has determined that the object would not be a hazard to air navigation if it were marked and/or lighted. Find guidance on marking and lighting objects in AC 70/7460-1, Obstruction Marking and Lighting.
c. Notification requirements. Part 77 requires persons proposing certain construction or alteration to give 45-day notice to the FAA of their intent. Use FAA Form 7460-1, Notice of Proposed Construction or Alteration to provide notification. See https://oeaaa.faa.gov for more information and to download the form.
d. Heliport development plans. Future public heliport development plans and feasibility studies on file with the FAA may influence the determinations resulting from part 77 studies. Owners of public heliports and owners of private heliports with FAA-approved instrument approach procedures can ensure full consideration of future heliport development in part 77 studies only when they file plans with the FAA. Include in heliport plan data the coordinates and elevations of planned FATO(s), approach/departure paths including their azimuths, and types of approaches for any new FATO or modification of an existing FATO.
AC 150/5390-2C 4/24/2012 Example of a Heliport Location Map
Figure 1–3. Example of a Heliport Location Map
112. Federal assistance. The FAA administers a grant program that provides financial assistance to eligible sponsors to develop a public use heliport. Information on federal aid program eligibility requirements is available from FAA Airports Regional and District Offices and on the FAA Airports web site, www.faa.gov/airports.
Figure 1-3 · page 18Picture of the page from the copy saved here
113. Environmental impact analyses. The National Environmental Policy Act of 1969 requires the FAA to consider potential environmental impacts prior to agency decision making, including, for example, the decision to fund or approve a project, plan, license, permit, certification, rulemaking, or operations specification, unless these actions are within an existing categorical exclusion and no
extraordinary circumstances exist. Actions that may require an environmental assessment are normally associated with federal grants or heliport layout plan approvals leading to the construction of a new heliport or significant expansion of an existing heliport.
a. Assessment items. An environmental assessment addresses noise, historic and cultural resources, wildlife, energy conservation, land usage, air quality, water quality, pollution prevention, light emissions and other visual effects, electromagnetic fields, other public health and safety issues, the “no action” alternative and a reasonable range of feasible alternatives, including mitigation not integrated into the alternative initially. It also describes the action taken to ensure public involvement in the planning process. An opportunity for a public hearing may be required for the federally funded development of, or significant improvement to, an existing heliport.
b. Guidance. FAA Order 5050.4, National Environmental Policy Act (NEPA) Implementing Instructions for Airport Projects, and FAA Order 1050.1, Polices and Procedures for Considering Environmental Impacts, and other supplemental guidance from FAA Air Traffic and Flight Standards provide guidance on environmental impact analysis. Contact state and local governments, including metropolitan planning organizations and local transit agencies, directly as they may also require an environmental report. The procedures in AC 150/5020-1, Noise Control and Compatibility Planning for Airports, describe a means of assessing the noise impact. Contact the appropriate FAA Airports Regional or District Office for current information related to assessing noise impact of heliports. Proponents of non-federally assisted heliports work with local governmental authorities concerning environmental issues.
114. Access to heliports by individuals with disabilities. Congress has passed various laws concerning access to airports. Since heliports are a type of airport, these laws are similarly applicable. Find guidance in AC 150/5360-14, Access to Airports by Individuals with Disabilities.
115. State role. Many state departments of transportation, aeronautical commissions, or similar authorities require prior approval and, in some instances, a license for the establishment and operation of a heliport. Several states administer a financial assistance program similar to the federal program and are staffed to provide technical advice. Contact your respective state aeronautics commissions or departments for particulars on licensing and assistance programs. Contact information for state aviation agencies is available at http://www.faa.gov/airports/resources/state_aviation.
116. Local role. Some communities have enacted zoning laws, building codes, fire regulations, etc. that can affect heliport establishment and operation. Some have or are in the process of developing codes or ordinances regulating environmental issues such as noise and air pollution. A few localities have enacted specific rules governing the establishment of a heliport. Therefore, make early contact with officials or agencies representing the local zoning board, the fire, police, or sheriff's department, and the elected person(s) who represent the area where the heliport is to be located.
117. Related referenced material. Find a list of related and referenced publications in Appendix D.
Offsite
Develop
ment Requiring Noti ce to the FAA
Figure 1–4. Offsite Development Requiring Notice to the FAA
Chapter 2. General Aviation Heliports › 202. Applicability.
Chapter 2. General Aviation Heliports
201. General. A general aviation heliport accommodates helicopters used by individuals, corporations, and helicopter air taxi services. While general aviation heliports may be publicly owned, this is not required. Most general aviation heliports are privately owned.
202. Applicability. The standards in this chapter apply to projects funded under the Airport Improvement Program (AIP) or the Passenger Facility Charge (PFC) program. For other projects/heliports, these standards are the FAA’s recommendations for designing all general aviation heliports. The design standards in this chapter assume that there will never be more than one helicopter within the final approach and takeoff area (FATO) and the associated safety area. If there is a need for more than one touchdown and liftoff area (TLOF) at a heliport, locate each TLOF within its own FATO and within its own safety area. Figure 2–1 illustrates the essential features of a general aviation heliport.
Essential Features of a Heliport: General Aviation
Figure 2-1 · page 21Picture of the page from the copy saved here
Figure 2–1. Essential Features of a Heliport: General Aviation
203. Prior permission required (PPR) facilities. The standards in this AC are recommended for all heliports. As PPR heliports are never eligible for federal financial assistance, do not interpret any recommendation in this AC that is not required by federal law or regulation as mandatory for PPR heliports. Recommendations for PPR heliports are provided in recognition of the unique nature of facilities where the operator ensures pilots are thoroughly familiar with the heliport, its procedures, and any facility limitations.
Chapter 2. General Aviation Heliports › 206. Basic layout.
204. Access by individuals with disabilities. Various laws require heliports operated by public entities and those receiving federal financial assistance to meet accessibility requirements. See paragraph 114.
205. Heliport site selection.
a. Long term planning. The FAA encourages public agencies and others planning to develop a general aviation heliport to consider the possible future need for instrument operations and expansion.
b. Property requirements. The property needed for a general aviation heliport depends upon the volume and types of users, size of helicopters, and the scope of amenities provided. Property needs for helicopter operators and for passenger amenities frequently exceed those for “airside” purposes.
c. Turbulence. Air flowing around and over buildings, stands of trees, terrain irregularities, etc. can create turbulence on ground-level and roof-top heliports that may affect helicopter operations. Where the FATO is located near the edge and top of a building or structure, or within the influence of turbulent wakes from other buildings or structures, assess the turbulence and airflow characteristics in the vicinity of, and across the surface of the FATO to determine if an air-gap between the roof, roof parapet or supporting structure, and/or some other turbulence mitigating design measure is necessary. FAA Technical Report FAA/RD-84/25, Evaluating Wind Flow around Buildings on Heliport Placement, addresses the wind’s effect on helicopter operations. Take the following actions in selecting a site to minimize the effects of turbulence.
(1) Ground-level heliports. Features such buildings, trees, and other large objects can cause air turbulence and affect helicopter operations from sites immediately adjacent to them. Therefore, locate the landing and takeoff area away from such objects in order to minimize air turbulence in the vicinity of the FATO and the approach/departure paths.
(2) Elevated heliports. Establishing a 6 foot (1.8 m) or more air gap on all sides above the level of the roof will generally minimize the turbulent effect of air flowing over the roof edge. Keep air gaps free at all times of objects that would obstruct the airflow. If it is not practical to include an air gap or some other turbulence mitigating design measure where there is turbulence, operational limitations may be necessary under certain wind conditions. See paragraph 101.
d. Electromagnetic effects. Nearby electromagnetic devices, such as a large ventilator motor, elevator motor or other devices that consume large amounts of electricity may cause temporary aberrations in the helicopter magnetic compass and interfere with other onboard navigational equipment.
206. Basic layout. A basic heliport consists of a TLOF contained within a FATO. A safety area surrounds the FATO. Table 2-1 shows how the standards for safety area width vary as a function of heliport markings. The relationship of the TLOF to the FATO and the safety area is shown in Figure 2–2. A FATO contains only one TLOF. Provide appropriate approach/departure airspace to allow safe approaches to and departures from landing sites. To the extent feasible, align the preferred approach/departure path with the predominant winds. See paragraph 210.
Figure 2-2 · page 24Picture of the page from the copy saved here
Chapter 2. General Aviation Heliports › 207. Touchdown and liftoff area (TLOF).
Table 2-1. Minimum VFR Safety Area Width as a Function of General Aviation and PPR Heliport Markings
General aviation heliports
1/3 RD but not less than 20 ft (6 m)**
1/3 RD but not less than 30 ft (9 m)**
½D but not less than
20 ft (6 m)
½ D but not less than
30 ft (9 m)
PPR heliports
1/3 RD but not less than 10 ft (3 m) **
1/3 RD but not less than 20 ft (6 m)**
½ D but not less than
20 ft (6 m)
½ D but not less than
30 ft (9 m)
TLOF perimeter marked Yes Yes No No
FATO perimeter marked Yes Yes Yes Yes
Standard “H” marking Yes No Yes No
D: Overall length of the design helicopter RD: Rotor diameter of the design helicopter ** Also applies when the FATO is not marked. Do not mark the FATO if (a) the FATO (or part of the FATO) is a non-load bearing surface and/or (b) the TLOF is elevated above the level of a surrounding loadbearing area.
207. Touchdown and liftoff area (TLOF).
a. TLOF location. TLOFs of general aviation heliports are at ground level, on elevated structures, and at rooftop level. Center the TLOF within the FATO. At a PPR rooftop or other PPR elevated facility, where the entire FATO is not load-bearing, locating the TLOF in a load-bearing area (LBA) that is as large as possible may provide some operational advantages. In this case, locate the TLOF in the center of the LBA.
b. TLOF size. Design the TLOF so the minimum dimension (length, width, or diameter) is at least equal to the RD of the design helicopter (except as noted in (2) below). Design the TLOF to be rectangular or circular. Each has its advantages. A square or rectangular shape provides the pilot with better alignment cues than a circular shape, but a circular TLOF may be more recognizable in an urban environment. Increasing the LBA centered on the TLOF may provide some safety and operational advantages. At PPR facilities, if only a portion of the TLOF is paved, design the TLOF so the minimum length and width of this paved portion is not less than two times the maximum dimension (length or width) of the undercarriage of the design helicopter. Locate the center of the TLOF in the center of this paved portion. To avoid the risk of catching a skid and the potential for a dynamic rollover, make sure there is no difference in elevation between the paved and unpaved portions of the TLOF.
(1) Elevated public general aviation heliport. If the FATO outside the TLOF is not loadbearing, increase the minimum width, length or diameter of the TLOF to the overall length (D) of the design helicopter. See paragraph 207.b(3).
(2) Elevated PPR heliports. At PPR rooftop or elevated facilities where the height of the TLOF surface above the adjacent ground or structure is no greater than 30 inches (76 cm), and there is a solid adjacent ground or structure equal to the rotor diameter (RD) able to support 20 lbs/sq ft (98 kg/sq m) live load, design the minimum dimension of the TLOF to be at least the smaller of the RD and two times the maximum dimension (length or width) of the undercarriage of the design helicopter. Locate the center of the LBA of the TLOF in the center of the FATO.
(3) Elongated TLOF. An elongated TLOF can provide an increased safety margin and greater operational flexibility. As an option, design an elongated TLOF with a landing position in the center and two takeoff positions, one at either end. Design the landing position to have a minimum length equal to the RD of the design helicopter. If the TLOF is elongated, also provide an elongated FATO. Figure 2–3 shows an elongated TLOF and an elongated FATO.
TLOF/
FATO
Safe
ty
A
re
a
Re
latio
nships and Minimum D
imensi
ons:
Gene
ra l Aviati
on
Figure 2–2. TLOF/FATO Safety Area Relationships and Minimum Dimensions:
General Aviation
Elon
ga
te
d
FA
TO wi th Two
Take
off P
os itions: Genera
l Avia
tion
Figure 2–3. Elongated FATO with Two Takeoff Positions: General Aviation
c. Ground-level TLOF surface characteristics.
(1) Design loads. Design the TLOF and any supporting TLOF structure to be capable of supporting the dynamic loads of the design helicopter.
Figure 2-3 · page 25Picture of the page from the copy saved here
(2) Paving. Provide either a paved or aggregate-turf surface for the TLOF (see AC 150/5370-10, Standards for Specifying Construction of Airports items P-217, Aggregate-Turf Pavement and P-501, Portland Cement Concrete Pavement). Use portland cement concrete (PCC) when feasible for groundlevel facilities. An asphalt surface is less desirable for heliports as it may rut under the wheels or skids of
a parked helicopter. This has been a factor in some rollover accidents. Use a broomed or roughened pavement finish to provide a skid-resistant surface for helicopters and non-slippery footing for people. For PPR heliports where only a portion of the TLOF is paved, design the paved portion to dynamic loadbearing. Design the adjacent ground or structure of the TLOF for the static loads of the design helicopter.
d. Rooftop and other elevated TLOFs.
(1) Design loads. Design elevated TLOFs and any TLOF supporting structure to capable of supporting the dynamic loads of the design helicopter described in paragraph 707.b. An elevated heliport is illustrated in Figure 2–4.
Figure 2-4 · page 27Picture of the page from the copy saved here
(2) Elevation. Elevate the TLOF above the level of any obstacle in the FATO and safety area that cannot be removed.
(3) Obstructions. Elevator penthouses, cooling towers, exhaust vents, fresh-air vents, and other raised features can affect heliport operations. Establish control mechanisms to ensure obstruction hazards are not installed after the heliport is operational.
(4) Air quality. Helicopter exhaust can affect building air quality if the heliport is too close to fresh air vents. When designing a building intended to support a helipad, locate fresh air vents accordingly. When adding a heliport to an existing building, relocate fresh air vents if necessary or, if that is not practical, installing charcoal filters or a fresh air intake bypass louver system for HVAC systems may be adequate.
(5) TLOF surface characteristics. Construct rooftop and other elevated heliport TLOFs of metal or concrete (or other materials subject to local building codes). Use a finish for TLOF surfaces that provides a skid-resistant surface for helicopters and non-slippery footing for people.
(6) Safety net. If the platform is elevated 4 feet (1.2 m) or more above its surroundings, Title 29 CFR Part 1910.23, Guarding Floor and Wall Openings and Holes, requires the provision of fall protection. The FAA recommends such protection for all platforms elevated 30 inches (76 cm) or more. However, do not use permanent railings or fences since they would be safety hazards during helicopter operations. As an option, install a safety net meeting state and local regulations but not less than 5 feet (1.5 m) wide. Design the safety net to have a load carrying capability of 25 lbs/sq ft (122 kg/sq m). Make sure the net, as illustrated in Figure 2–28, does not project above the level of the TLOF. Fasten both the inside and outside edges of the safety net to a solid structure. Construct nets of materials that are resistant to environmental effects.
HELIPORT BEACON
LIGHTED WIND CONE
FATO
RAISED TLOF
5 FT [1.5 M] WIDE SAFETY NET
SAFETY AREA
FLUSH TLOF
LIGHTING
RAMP
Post at Personnel Entrance
CAUTION
HELICOPTER LANDING
AREA
SAFETY
AVOID FRONT AND REAR
AREA OF HELICOPTER
STAY CLEAR
OF THE AVOID FRONT AND REAR TAIL ROTOR AREA OF HELICOPTER Notes:
APPROACH AND LEAVE HELICOPTER AS DIRECTED BY CREW
IN A CROUCHED MANNER WHEN ROTORS ARE TURNING
1. See Figure 2-28, Elevated TLOF Perimeter Lighting: General INSTRUCTIONS Aviation, for detailed views of the safety net and lighting. AUTHORIZED
PERSONNEL 2. TLOF size and weight limitation box is not ONLY shown for clarity.
Figure 2–4. Elevated Heliport: General Aviation
Chapter 2. General Aviation Heliports › 208. Final approach and takeoff area (FATO).
(7) Access to elevated TLOFs. Title 29 CFR Part 1926.34, Means of Egress, requires two separate access points for an elevated structure such as one supporting an elevated TLOF. Title 29 CFR Part 1910.24, Fixed Industrial Stairs applies to stairs. Design handrails required by this regulation to fold down or be removable to below the level of the TLOF so they will not be hazards during helicopter operations.
e. TLOF gradients. See paragraph 702 for TLOF gradient standards.
208. Final approach and takeoff area (FATO). A general aviation heliport has at least one FATO. The FATO contains a TLOF within its borders at which arriving helicopters terminate their approach and from which departing helicopters take off.
a. FATO size.
(1) Design the minimum width, length, or diameter of a FATO to be at least 1.5 times the overall length (D) of the design helicopter. Design the FATO to be circular or rectangular, regardless of the shape of the TLOF. At elevations above 1,000 feet MSL, include a longer, rectangular FATO to provide an increased safety margin and greater operational flexibility. Use the additional FATO length depicted in Figure 2–5. Where the operator of a PPR heliport chooses not to provide additional FATO length, the operator makes sure that all pilots using the facility are thoroughly knowledgeable with this and any other facility limitations.
(2) Design the minimum distance between the TLOF perimeter and the FATO perimeter to be not less than the distance (¾ D - ½ RD) where D is the overall length and RD is the rotor diameter of the design helicopter. Note that if the TLOF and FATO are not of similar shape, this applies at all points of the TLOF perimeter. The relationship of the TLOF to the FATO and the safety area is shown in Figure 2– 2.
Figure 2-5 · page 28Picture of the page from the copy saved here
b. FATO surface characteristics. If the heliport operator marks the TLOF, the FATO outside the TLOF need not load-bearing.
(1) Ground level public general aviation heliports. If the heliport operator does not mark the TLOF (see paragraph 215.a), and/or intends that the helicopter be able to land anywhere within the FATO, design the FATO outside the TLOF and any FATO supporting structure, like the TLOF, to be capable of supporting the dynamic loads of the design helicopter, as described in paragraph 707.b.
(2) Ground level PPR heliports. If the heliport operator does not mark the TLOF, and/or intends for the helicopter to be able to land anywhere within the FATO, design the FATO outside the TLOF and any FATO supporting structure, like the TLOF, to be capable of supporting the dynamic loads of the design helicopter, as described in paragraph 707.b.
Addi
tion
al F
AT
O Le ng th f or H
el
ipo
rts
a
t Higher Elevations: General A
viation
Figure 2–5. Additional FATO Length for Heliports at Higher Elevations:
General Aviation
(3) Elevated heliports. As an option, design the FATO outside the TLOF to extend into clear airspace. However, there are some helicopter performance benefits and increased operational flexibility if the FATO outside the TLOF is load bearing. Design the FATO outside of the TLOF to be load-bearing, or increase the minimum width and length or diameter of TLOF to the overall length of the design helicopter.
(4) Elevated PPR heliports. For elevated PPR heliports, if the heliport operator intends to mark the TLOF, as an option design the FATO outside the TLOF and the safety area to extend into the clear airspace (see Figure 2–4). If the heliport operator does not mark the TLOF, and/or intends that the helicopter be able to land anywhere within the FATO, design the FATO outside the TLOF and any FATO supporting structure, like the TLOF, to support the dynamic loads of the design helicopter. As an option, increase the length and width or diameter of the LBA without a corresponding increase in the size of the FATO.
(5) If the FATO is load-bearing, design the portion abutting the TLOF to be contiguous with the TLOF, with the adjoining edges at the same elevation.
(6) If the FATO is unpaved, treat the FATO to prevent loose stones and any other flying debris caused by rotor downwash.
(7) When the FATO or the LBA in which it is located is elevated 4 feet (1.2 m) or more above its surroundings, part 1910.23 requires the provision of fall protection. The FAA recommends such protection for all platforms elevated 30 inches (76 cm) or more. However, do not use permanent railings or fences since they would be safety hazards during helicopter operations. As an option, install a safety net meeting state and local regulations but not less than 5 feet (1.5 m) wide. Design the safety net to have a load carrying capability of 25 lbs/sq ft (122 kg/sq m). Make sure the net, as illustrated in Figure 2–28,
Chapter 2. General Aviation Heliports › 210. VFR approach/departure paths.
does not project above the level of the TLOF. Fasten both the inside and outside edges of the safety net to a solid structure. Construct nets of materials that are resistant to environmental effects.
c. Mobile objects within the FATO. The FATO design standards of this AC assume the TLOF and FATO are closed to other aircraft if a helicopter or other mobile object is within the FATO or the safety area.
d. Fixed objects within the FATO. Remove all fixed objects projecting above the FATO elevation except for lighting fixtures, which may project a maximum of 2 inches (5 cm). See Figure 7–3. For ground level heliports, remove all above-ground objects to the extent practicable.
e. FATO/FATO separation. If a heliport has more than one FATO, separate the perimeters of the two FATOs so the respective safety areas do not overlap. This separation assumes simultaneous approach/departure operations will not take place. If the heliport operator intends for the facility to support simultaneous operations, provide a minimum 200 foot (61 m) separation.
f. FATO gradients. See paragraph 703 for FATO gradient standards.
209. Safety area. A safety area surrounds a FATO.
a. Safety area width. The standards for the width of the safety area are shown in Table 2-1. The value is the same on all sides. The provision or absence of standard heliport markings affects the width standards. As an option, design the safety area to extend into clear airspace.
b. Mobile objects within the safety area. The safety area design standards of this AC assume the TLOF and FATO are closed to other aircraft if a helicopter or other mobile object is within the FATO or the safety area.
c. Fixed objects within a safety area. Remove all fixed objects within a safety area projecting above the FATO elevation except for lighting fixtures, which may project a maximum of 2 inches (5 cm). See Figure 7–3. For ground level heliports, remove all above-ground objects to the extent practicable.
d. Safety area surface. The safety area need not be load bearing. Figure 2–6 depicts a safety area extending over water. If possible, design the portion of the safety area abutting the FATO to be contiguous with the FATO with the adjoining edges at the same elevation. This is needed to avoid the risk of catching a helicopter skid or wheel. Clear the safety area of flammable materials and treat the area to prevent loose stones and any other flying debris caused by rotor wash.
e. Safety area gradients. Find safety area gradient standards in Chapter 7.
210. VFR approach/departure paths. The purpose of approach/departure airspace, shown in Figure 2–7 and Figure 2–8 is to provide sufficient airspace clear of hazards to allow safe approaches to and departures from the TLOF.
N
o
n
- load-bearing
FATO and Safe ty Area: Gen
eral Avia tion
Figure 2–6. Non-load-bearing FATO and Safety Area: General Aviation
Figure 2-6 · page 31Picture of the page from the copy saved here
a. Number of approach/departure paths. Align preferred approach/departure paths with the predominant wind direction to avoid downwind operations and minimize crosswind operations. To accomplish this, design the heliport with more than one approach/departure path. Base other approach/departure paths on the assessment of the prevailing winds or, when this information is not available, separate such flight paths and the preferred flight path by at least 135 degrees. See Figure 2–7, Figure 2–8, and Figure 2–9. At a PPR heliport that has only one approach/departure path, the operator makes sure all pilots using the facility are thoroughly knowledgeable with this and any other facility limitations. A second flight path provides additional safety margin and operational flexibility. If it is not feasible to provide complete coverage of wind through multiple approach/departure paths, operational limitations maybe necessary under certain wind conditions. See paragraph 101.
Figure 2-7 · page 33Picture of the page from the copy saved here
b. VFR approach/departure and transitional surfaces. Figure 2–7 illustrates the approach/departure and transitional surfaces.
(1) An approach/departure surface is centered on each approach/departure path. The approach/departure path starts at the edge of the FATO and slopes upward at 8:1 (8 units horizontal in 1 unit vertical) for a distance of 4,000 feet (1,219 m) where the width is 500 feet (152 m) at a height of 500 feet (152 m) above the heliport elevation.
(2) The transitional surfaces start from the edges of the FATO parallel to the flight path center line, and from the outer edges of the 8:1 approach/departure surface, and extend outwards at a slope of 2:1 (2 units horizontal in 1 unit vertical) for a distance of 250 feet (76 m) from the centerline. The transitional surface does not apply to the FATO edge opposite the approach/departure surface.
(3) Make sure the approach/departure and transitional surfaces are free of penetrations unless an FAA aeronautical study determines such penetrations not to be hazards. The FAA conducts such aeronautical studies only at public heliports, heliports operated by a federal agency or the Department of Defense, and private airports with FAA-approved approach procedures. Paragraph 111 provides additional information on hazards to air navigation.
(4) At PPR facilities, an alternative to considering transitional surfaces is to increase the size of the 8:1 approach/departure surface for a distance of 2,000 feet (610 m) as shown in Figure 2–9 and Figure 2–11. The lateral extensions on each side of the 8:1 approach/departure surface start at the width of the FATO and are increased so at a distance of 2,000 feet (610 m) from the FATO they are 100 feet (30 m) wide. Make sure obstacles do not penetrate into both Area A and Area B. Make sure obstacles do not penetrate into Area A or Area B unless the FAA determines that the penetration is not a hazard. Mark or light all such penetrations. See paragraph 111 for more information on hazard determinations.
Figure 2-9 · page 35Picture of the page from the copy saved here
c. Curved VFR approach/departure paths. As an option, include one curve in VFR approach/departure paths. As an option, design these paths to use the airspace above public lands, such as freeways or rivers. When including a curved portion in the approach/departure path, make sure the sum of the radius of the arc defining the center line and the length of the straight portion originating at the FATO is not less than 1,886 feet (575 m). Design the approach/departure path so the minimum radius of the curve is 886 feet (270 m) and the curve follows a 1,000 feet (305 m) straight section. Design the approach/departure path so the combined length of the center line of the curved portion and the straight portion is 4,000 feet (1,219 m). See Figure 2–8. Figure 2–10 shows a curved approach/departure path for an 8:1 approach/departure surface.
V
F
R
H e
l
i
p
ort A
pproach/Departure and Trans
itional Surfaces: Gener al Aviation
Figure 2–7. VFR Heliport Approach/Departure and Transitional Surfaces: General Aviation
Cu
r
v
e
d
A p
p
r
o
a c
h
/
Departu re: Gene
ral Aviation
Figure 2-8 · page 34Picture of the page from the copy saved here
Figure 2–8. Curved Approach/Departure: General Aviation
V F
R
P
P
R
He liport Lateral Extens ion o
f the 8:1 Approach / Departure Surface: General Aviation
Figure 2–9. VFR PPR Heliport Lateral Extension of the 8:1 Approach / Departure Surface: General Aviation
V
FR P P R H
e
l
i
p
o r t
Later al Ext ens
io
n of the C urved 8:1 Appr
oach / Departure Surface
: General Aviation
Figure 2–10. VFR PPR Heliport Lateral Extension of the Curved 8:1 Approach / Departure Surface: General Aviation
Figure 2-10 · page 36Picture of the page from the copy saved here
Chapter 2. General Aviation Heliports › 213. Taxiways and taxi routes.
d. Flight path alignment guidance. As an option, use flight path alignment markings and/or flight path alignment lights (see paragraphs 215 and 216) where it is desirable and practicable to indicate available approach and/or departure flight path direction(s). See Figure 2–11.
e. Periodic review of obstructions. Vigilant heliport operators reexamine obstacles in the vicinity of approach/departure paths on at least an annual basis. This reexamination includes an appraisal of the growth of trees near approach and departure paths. Paragraph 111 provides additional information on hazards to air navigation. Pay particular attention to obstacles that need to be marked or lighted. It may be helpful to maintain a list of the GPS coordinates and the peak elevation of obstacles.
211. Heliport protection zone (HPZ). The FAA recommends the establishment of an HPZ for each approach/departure surface. The HPZ is the area under the 8:1 approach/departure surface starting at the FATO perimeter and extending out for a distance of 280 feet (85.3 m), as illustrated in Figure 2–12�. The HPZ is intended to enhance the protection of people and property on the ground. This is achieved through heliport owner control over the HPZ. Such control includes clearing HPZ areas (and maintaining them clear) of incompatible objects and activities. The FAA discourages residences and places of public assembly in an HPZ. (Churches, schools, hospitals, office buildings, shopping centers, and other uses with similar concentrations of persons typify places of public assembly.) Do not locate hazardous materials, including fuel, in the HPZ.
212. Wind cone.
a. Specification. Use a wind cone conforming to AC 150/5345-27, Specification for Wind Cone Assemblies, to show the direction and magnitude of the wind. Use a color that provides the best possible color contrast to its background.
Figure 2-12 · page 39Picture of the page from the copy saved here
b. Wind cone location. Locate the wind cone so it provides the pilot with valid wind direction and speed information in the vicinity of the heliport under all wind conditions.
(1) At many landing sites, there may be no single, ideal location for the wind cone. At other sites, it may not be possible to site a wind cone at the ideal location. In such cases, install more than one wind cone in order to provide the pilot with all the wind information needed for safe operations.
(2) Place the wind cone so a pilot on the approach path can see it clearly when the helicopter is 500 feet (150 m) from the TLOF.
(3) Place the wind cone so pilots can see it from the TLOF.
(4) To avoid presenting an obstruction hazard, locate the wind cone(s) outside the safety area, and so it does not penetrate the approach/departure or transitional surfaces.
c. Wind cone lighting. At a heliport intended for night operations, illuminate the wind cone, either internally or externally, to ensure it is clearly visible.
213. Taxiways and taxi routes. Taxiways and taxi routes provide for the movement of helicopters from one part of a landing facility to another. They provide a connecting path between the FATO and a parking area. They also provide a maneuvering aisle within the parking area. A taxi route includes the taxiway plus the appropriate clearances needed on both sides. The relationship between a taxiway and a taxi route is illustrated in Figure 2–13, Figure 2–14, and Figure 2–15. At heliports with no parking or refueling area outside the TLOF(s), it is not necessary to provide a taxi route or taxiway.
Figure 2–11. Flight Path Alignment Marking and Lights: General Aviation
H e
l
i
p
o r
t
P
rot ection Zone: Gener al Aviat
ion
Figure 2–12. Heliport Protection Zone: General Aviation
Taxiway/Taxi Route Relationship – Paved Taxi way: General Aviation
Figure 2–13. Taxiway/Taxi Route Relationship – Paved Taxiway: General Aviation
Taxiway/Taxi Route Relation
ship – Unpaved Taxiway with Raised Edge Mar
kers: General Aviation
Figure 2–14. Taxiway/Taxi Route Relationship – Unpaved Taxiway with Raised Edge Markers: General Aviation
Taxiway/Taxi Route Relationship – Unp
aved Taxiway with Flush Edge
Markers: General Aviation
Figure 2–15. Taxiway/Taxi Route Relationship – Unpaved Taxiway with Flush Edge Markers: General Aviation
Figure 2-14 · page 41Picture of the page from the copy saved here
Chapter 2. General Aviation Heliports › 214. Helicopter parking.
a. Taxiway/taxi route widths. The dimensions of taxiways and taxi routes are a function of helicopter size, taxiway/taxi route marking, and type of taxi operations (ground taxi versus hover taxi). These dimensions are defined in Table 2-2. Normally, the requirement for hover taxi dictates the taxiway/taxi route widths. However, when the fleet comprises a combination of large ground taxiing helicopters and smaller air taxiing helicopters, the larger aircraft may dictate the taxiway/taxi route widths. If wheel-equipped helicopters taxi with wheels not touching the surface, design the facility with hover taxiway widths rather than ground taxiway widths. Where the visibility of the centerline marking cannot be guaranteed at all times, such as locations where snow or dust commonly obscure the centerline marking and it is not practical to remove it, determine the minimum taxiway/taxi route dimensions as if there was no centerline marking.
b. Surfaces. For ground taxiways, provide a portland cement concrete, asphalt, or stabilized surfaces, such as turf, in accordance with the standards of items P-217 of AC 150/5370-10. For unpaved portions of taxiways and taxi routes, provide a turf cover or treat the surface in some way to prevent dirt and debris from being raised by a taxiing helicopter’s rotor wash.
c. Gradients. Taxiway and taxi route gradient standards are defined in Chapter 7.
214. Helicopter parking. If more than one helicopter at a time is expected at a heliport, design the facility with an area designated for parking helicopters. The size of this area depends on the number and size of specific helicopters to be accommodated. It is not necessary that every parking position accommodate the design helicopter. Construct individual parking positions to accommodate the helicopter size and weights expected to use the parking position at the facility. However, use the design helicopter to determine the separation between parking positions and taxi routes. Use the larger helicopter to determine the separation between parking positions intended for helicopters of different sizes. Build the parking positions to support the static loads of the helicopter intended to use the parking area. Design parking areas as one large, paved, apron or as individual, paved, parking positions. Ground taxi turns of wheeled helicopters are significantly larger than a hover turn. Consider the turn radius of helicopters when designing taxi intersections and parking positions for wheeled helicopters. Design heliport parking areas so helicopters will be parked in an orientation that keeps the “avoid areas” around the tail rotors clear of passenger walkways. See Figure 2–16, Figure 2–17, and Figure 2–19.
Figure 2-17 · page 46Picture of the page from the copy saved here
a. Location. Do not locate aircraft parking areas under an approach/departure surface. However, as an option, allow aircraft parking areas under the transitional surfaces.
(1) For “turn around” parking positions, locate the parking position to provide a minimum distance between the tail rotor circle and any object, building, safety area, or other parking position. The minimum distance is 10 feet (3 m) for ground taxi operations and the greater of 10 feet (3 m) or 1/3 RD for hover taxi operations. See Figure 2–19.
(2) For “taxi-through” and “back-out” parking positions, locate the parking position to provide a minimum distance between the main rotor circle and any object, building, safety area, or other parking position. The minimum distance is 10 feet (3 m) for ground taxi operations and the greater of 10 feet (3 m) or 1/3 RD for hover taxi operations. See Figure 2–20.
(3) Locate the parking position to provide a minimum distance between the main rotor circle and the edge of any taxi route. Design parking positions such that the helicopter taxis through, turns around, or backs out to depart. The minimum distance is 1/3 RD for “turn around” and “taxi through” parking areas, and ½ RD for “back-out” parking areas. See Figure 2–16, Figure 2–17, and Figure 2–18.
Table 2-2. Taxiway/Taxi Route Dimensions – General Aviation Heliports
Taxiway
(TW)
Type
Minimum
Width of Paved Area
Centerline
Marking
Type
TW Edge
Marking
Type
Lateral Separation Between TW
Edge Markings
Total Taxi Route Width
Ground Taxiway
2 x UC Painted
Painted 2 x UC
1 ½ RD
Elevated 1 RD but not greater than 35 ft (10.7 m)
Unpaved but stabilized for ground taxi
None
Flush 2 x UC
Elevated 1 RD but not greater than 35 ft (10.7 m)
Hover Taxiway
2 x UC Painted Painted 2 x UC
2 RD
Unpaved None Elevated or Flush
1 RD but not greater than 35 ft (10.7 m)
RD: rotor diameter of the design helicopter TW: taxiway UC: undercarriage length or width (whichever is greater) of the design helicopter
Figure 2-18 · page 47Picture of the page from the copy saved here
Parking Area Desig n – “Taxi-through”
Parking Positions:
General
Aviation
Figure 2–16. Parking Area Design – “Taxi-through” Parking Positions: General Aviation
Parking Ar ea Des ign – “Turn-aroun d” Pa rking Positions: Ge
neral Aviati
on
Figure 2–17. Parking Area Design – “Turn-around” Parking Positions: General Aviation
Parking Ar
ea De
sign – “Back-out” Pa rking Po
sitions: Gen
eral Aviati
on
Figure 2–18. Parking Area Design – “Back-out” Parking Positions: General Aviation
“T
u
rn
-
a
r
ou
nd
”
Pa
rk
i
n
g
Po
si
ti
on
M
ar
ki
n
g
:
G
e
ne
ral Aviation
Figure 2–19. “Turn-around” Parking Position Marking: General Aviation
"
T
a x
i
- t h
r o u g h ”
a n
d
“
B
a
ck
-
o
ut
”
Pa
rk
in
g
P
o
si
ti
on Marking: Gen
eral Aviati on
Figure 2–20. “Taxi-through” and “Back-out” Parking Position Marking: General Aviation
b. Size. Parking position sizes are dependent upon the helicopter size. The clearance between parking positions are dependent upon the type of taxi operations (ground taxi or hover taxi) and the intended paths for maneuvering in and out of the parking position. The more demanding requirement will dictate what is required at a particular site. Usually, the parking area requirements for skid-equipped helicopters will be the most demanding. However, when the largest helicopter is a very large, wheeled aircraft (for example, the S-61), and the skid-equipped helicopters are all much smaller, the parking requirements for wheeled helicopters may be the most demanding. If wheel-equipped helicopters taxi with wheels not touching the surface, design parking areas based on hover taxi operations rather than ground taxi operations.
(1) If all parking positions are the same size, design them to accommodate the largest helicopter that will park at the heliport.
(2) When there is more than one parking position, as an option design the facility with parking positions of various sizes with at least one position that will accommodate the largest helicopter that will park at the heliport. Design other parking positions to be smaller, for the size of the individual or range of individual helicopters parking at that position. Figure 2–21 provides guidance on parking position identification, size, and weight limitations.
(3) “Taxi-through” parking positions are illustrated in Figure 2–16. When using this design for parking positions, the heliport owner and operator take steps to ensure all pilots are informed that “turnaround” or “back-up” departures from the parking position are not permitted.
(4) “Turn-around” parking positions are illustrated in Figure 2–17.
(5) “Back-out” parking positions are illustrated in Figure 2–18. When using this design for parking positions, design the adjacent taxiway to accommodate hover taxi operations so the width of the taxiway will be adequate to support “back-out” operations.
Figure 2-21 · page 51Picture of the page from the copy saved here
c. Parking pads. When partially paving a parking area, design the smallest dimension of the paved parking pad to be a minimum of two times the maximum dimension (length or width, whichever is greater) of the undercarriage or the RD, whichever is less, of the largest helicopter that will use the parking position. Place the parking pad in the center of the parking position circle.
d. Walkways. At parking positions, provide marked walkways where practicable. Design the pavement to drain away from walkways.
e. Fueling. Design the facility to allow fueling with the use of a fuel truck or a specific fueling area with stationary fuel tanks.
(1) Various federal, state, and local requirements for petroleum handling facilities apply to systems for storing and dispensing fuel. Guidance is found in AC 150/5230-4, Aircraft Fuel Storage, Handling, and Dispensing on Airports. Additional information may be found in various National Fire Protection Association (NFPA) publications. For more reference material, see Appendix D.
P
a
r
k
i
ng Position Identification, Size, and Weight Limitations: General Aviation
Figure 2–21. Parking Position Identification, Size, and Weight Limitations: General Aviation
(2) Do not locate fueling equipment in the TLOF, FATO, or safety area. Design and mark separate fueling locations to minimize the potential for helicopters to collide with the dispensing equipment. Design fueling areas so there is no object tall enough to be hit by the main or tail rotor blades within a distance of RD from the center point of the position where the helicopter would be fueled (providing ½ RD clearance from the rotor tips). If this is not practical at an existing facility, install long fuel hoses.
Chapter 2. General Aviation Heliports › 215. Heliport markers and markings.
(3) Lighting. Light the fueling area if night fueling operations are contemplated. Ensure any light poles do not constitute an obstruction hazard.
f. Tiedowns. Install recessed tiedowns to accommodate extended or overnight parking of based or transient helicopters. Recess any tiedowns so they will not be a hazard to helicopters. Ensure any depression associated with the tiedowns is of a diameter not greater than ½ the width of the smallest helicopter landing wheel or landing skid anticipated to be operated on the heliport surface. In addition, provide storage for tiedown chocks, chains, cables and ropes off the heliport surface to avoid fouling landing gear. Find guidance on recessed tiedowns in AC 20-35, Tiedown Sense.
215. Heliport markers and markings. Markers and/or surface markings identify the facility as a heliport. Use paint or preformed materials for surface markings. (See AC 150/5370-10, Item P-620, for specifications for paint and preformed material.). As options, use reflective paint and reflective markers, though overuse of reflective material can be blinding to a pilot using landing lights. As an option, outline lines/markings with a 6-inch (15 cm) wide line of a contrasting color to enhance conspicuity. Place markings that define the edges of a TLOF, FATO, taxiway or apron within the limits of those areas. Use the following markers and markings.
a. Heliport identification marking. The identification marking identifies the location as a heliport, marks the TLOF and provides visual cues to the pilot.
(1) Standard heliport identification symbol. Mark the TLOF with a white “H” marking. The “H” has a minimum height of the lesser of 0.3 D or 10 feet (3 m). Locate the “H” in the center of the TLOF and orient it on the axis of the preferred approach/departure path. Place a one-foot wide bar under the “H” when it is necessary to distinguish the preferred approach/departure direction. The proportions and layout of the letter “H” are illustrated in Figure 2–23. For a height of “H” less than 10 feet (3 m), reduce other dimensions proportionately.
(2) Nonstandard heliport identification marking. As an option use a distinctive marking, such as a company logo, to identify the facility as a PPR heliport. However, a nonstandard marking does not necessarily provide the pilot with the same degree of visual cueing as the standard heliport identification symbol. To compensate, increase the size of the safety area when the standard heliport identification symbol “H” is not used. See Table 2-1.
b. TLOF markings.
Figure 2-23 · page 53Picture of the page from the copy saved here
(1) TLOF perimeter marking. Define the TLOF perimeter with markers and/or lines. If the heliport operator does not mark the TLOF, increase the size of the safety area as described in paragraph 209.a and Table 2-1.
(a) Paved TLOFs. Define the perimeter of a paved or hard surfaced TLOF with a continuous, 12-inch-wide (30 cm), white line. See Figure 2–25.
(b) Unpaved TLOFs. Define the perimeter of an unpaved TLOF with a series of 12-inchwide (30 cm), flush, in-ground markers, each approximately 5 feet (1.5 m) in length with end-to-end spacing of not more than 6 inches (15 cm). See Figure 2–25.
(2) Touchdown/positioning circle (TDPC) marking. A TDPC marking provides guidance to allow a pilot to touch down in a specific position on paved surfaces. When the pilot’s seat is over the
Figure 2-25 · page 53Picture of the page from the copy saved here
marking, the undercarriage will be inside the LBA, and all parts of the helicopter will be clear of any obstacle by a safe margin. A TDPC marking is a yellow circle with an inner diameter of ½ D and a line width of 18 in (46 m). Locate a TDPC marking in the center of a TLOF. (See Figure 2–23). As an option, at PPR heliports where the TLOF width is less than 16 feet (5 m), omit the TDPC marking.
(3) TLOF size and weight limitations. Mark the TLOF to indicate the length and weight of the largest helicopter it will accommodate, as shown in Figure 2–23. Place these markings in a box in the lower right-hand corner of a rectangular TLOF, or on the right-hand side of the “H” of a circular TLOF, when viewed from the preferred approach direction. The box is 5 feet (1.5 m) square. The numbers are 18 inches (46 cm) high. (See Figure C–1). If necessary, allow this marking to interrupt the TDPC marking. (See Figure 2–23 and Figure C–1.) The numbers are black with a white background. This marking is optional at a TLOF with a turf surface. This marking is also optional at PPR heliports, since the operator ensures all pilots using the facility are thoroughly knowledgeable with this and any other facility limitations.
(a) TLOF size limitation. This number is the length (D) of the largest helicopter the TLOF will accommodate, as shown in Figure 2–23. The marking consists of the letter “D” followed by the dimension in feet. Do not use metric equivalents for this purpose. Center this marking in the lower section of the TLOF size/weight limitation box.
(b) TLOF weight limitations. If a TLOF has limited weight-carrying capability, mark it with the maximum takeoff weight of the design helicopter, in units of thousands of pounds, as shown in Figure 2–23. Do not use metric equivalents for this purpose. Center this marking in the upper section of a TLOF size/weight limitation box. If the TLOF does not have a weight limit, add a diagonal line, extending from the lower left hand corner to the upper right hand corner, to the upper section of the TLOF size/weight limitation box. See Figure 2–23.
c. Extended pavement/structure markings. As an option, increase the pavement or structure without a corresponding increase in the length and width or diameter of the FATO to accommodate pedestrians and/or support operations. Whether or not this increased area is part of the LBA, mark the area outside the TLOF with 12-inch-wide (30 cm) diagonal black and white stripes. See Figure 2–24 for marking details.
d. FATO markings.
(1) FATO perimeter marking. Define the perimeter of a load-bearing FATO with markers and/or lines. Do not mark the FATO perimeter if any portion of the FATO is not a load-bearing surface. In such cases, mark the perimeter of the LBA (see paragraph (b) below).
(a) Paved FATOs. Define the perimeter of a paved load-bearing FATO with a 12-inch-wide (30 cm) dashed white line. Define the corners of the FATO. The perimeter marking segments are approximately 5 feet (1.5 m) in length, and with end-to-end spacing of approximately 5 feet (1.5 m). See Figure 2–25.
(b) Unpaved FATOs. Define the perimeter of an unpaved load-bearing FATO with 12-inchwide (30 cm), flush, in-ground markers. Define the corners of the FATO. The rest of the perimeter markers are approximately 5 feet (1.5 m) in length, and have end-to-end spacing of approximately 5 feet (1.5 m). See Figure 2–26.
S
t
a
n d
a
r
d
and Alternate TLOF Mar king: General Avia
tion
Figure 2–22. Standard and Alternate TLOF Marking:
General Aviation
S t
a
n d a
r
d
H
e l
i
port Identification Sym
bol, T
LOF Size and Weight Limitations: General Aviation
Figure 2–23. Standard Heliport Identification Symbol,
TLOF Size and Weight Limitations: General Aviation
E
x t e
n
d e d
P
avement / Structure Marking: General Aviation
Figure 2–24. Extended Pavement / Structure Marking: General Aviation
Paved TLOF /Paved FATO – Paved
TLOF/ Unpave d FATO – Marking:
General Aviati
on
Figure 2–25. Paved TLOF/Paved FATO – Paved TLOF/ Unpaved FATO – Marking: General Aviation
U
n
p
a
v
e
d
T L
O
F / U
n
paved FATO –
Marking:
General Aviation
Figure 2–26. Unpaved TLOF/Unpaved FATO – Marking: General Aviation
Figure 2-22 · page 54Picture of the page from the copy saved here
e. Flight path alignment guidance marking. An optional flight path alignment guidance marking consists of one or more arrows to indicate the preferred approach/departure direction(s). Mark it on the TLOF, FATO and/or safety area surface as shown in Figure 2–11. The shaft of the each arrow is 18 inches (50 cm) in width and at least 10 feet (3 m) in length. Use a color which provides good contrast against the background color of the surface. An arrow pointing toward the center of the TLOF depicts an approach direction. An arrow pointing away from the center of the TLOF depicts a departure direction. In the case of a flight path limited to a single approach direction or a single departure path, the arrow marking is unidirectional. In the case of a heliport with only a bidirectional approach/takeoff flight path available, the arrow marking is bidirectional.
f. Taxiway and taxi route markings.
(1) Paved taxiway markings. Mark the centerline of a paved taxiway with a continuous 6-inch (15 cm) yellow line. As an option, mark both edges of the paved portion of the taxiway with two continuous 6-inch (15 cm) wide yellow lines spaced 6 inches (15 cm) apart. Figure 2–13 illustrates taxiway centerline and edge markings.
(2) Unpaved taxiway markings. Use either raised or in-ground flush edge markers to provide strong visual cues to pilots. Space them longitudinally at approximately 15-foot (5 m) intervals on straight segments and at approximately 10-foot (3 m) intervals on curved segments. Figure 2–14 and Figure 2–15 illustrate taxiway edge markings.
(a) Raised-edge markers are blue, 4 inches (10 cm) in diameter, and 8 inches (20 cm) high, as illustrated in Figure 2–14.
(b) In-ground, flush edge markers are yellow, 12 inches (30 cm) wide, and approximately 5 feet (1.5 m) long.
(3) Raised edge markers in grassy areas. Tall grass sometimes obscures raised edge markers Address this issue by using 12-inch (30 cm) diameter solid material disks around the poles supporting the raised markers.
(4) Taxiway to parking position transition requirements. For paved taxiways and parking areas, taxiway centerline markings continue into parking positions and become the parking position centerlines.
g. Helicopter parking position markings. Helicopter parking positions have the following markings:
(1) Paved parking position identifications. Mark parking position identifications (numbers or letters) if there is more than one parking position. These markings are yellow characters 36 inches (91 cm) high. See Figure 2–21 and Figure C–1.
(2) Rotor diameter circle. Define the circle of the RD of the largest helicopter that will park at that position with a 6-inch (15 cm) wide, solid yellow line with an outside diameter of RD. In paved areas, this is a painted line (see Figure 2–21). In unpaved areas, use a series of flush markers, 6 inches (15 cm) in width, a maximum of 5 feet (1.5 m) in length, and with end-to-end spacing of approximately 5 feet (1.5 m).
(3) Touchdown/positioning circle (TDPC) marking. An optional TDPC marking provides guidance to allow a pilot to touch down in a specific position on paved surfaces. When the pilot’s seat is over the marking, the undercarriage will be inside the LBA, and all parts of the helicopter will be clear of any obstacle by a safe margin. A TDPC marking is a yellow circle with an inner diameter of ½ D and a line width of 18 in (46 cm). Locate a TDPC marking in the center of a parking area. See Figure 2–21 and Figure 2–25. The FAA recommends a TDPC marking for “turn-around” parking areas.
(4) Maximum length marking. This marking on paved surfaces indicates the D of the largest helicopter that the position is designed to accommodate (for example, 49). This marking consists of yellow characters at least 36 inches (91 cm) high. See Figure 2–21 and Figure C–1.
(5) Parking position weight limit. If a paved parking position has a weight limitation, mark it in units of 1,000 lbs as illustrated in Figure 2–21. (A 4 indicates a weight-carrying capability of up to 4,000 lbs. Do not use metric equivalents for this purpose.) This marking consists of yellow characters 36 inches (91 cm) high. When necessary to minimize the possibility of being misread, place a bar under the number. See Figure 2–21, Figure 2–25, and Figure C–1.
(6) Shoulder line markings. As an option, use shoulder line markings for paved parking areas (Figure 2–21) to ensure safe rotor clearance. Locate a 6-inch (15 cm) wide solid yellow shoulder line, perpendicular to the centerline and extending to the RD marking, so it is under the pilot’s shoulder such that the main rotor of the largest helicopter the position will accommodate will be entirely within the rotor diameter parking circle (see Figure 2–21). Use ¼ D from the center of parking area to define the location of shoulder line. The FAA recommends a shoulder line marking for “taxi-through” and “back-out” parking areas.
h. Walkways. Figure 2–21 illustrates one marking scheme.
i. Closed heliport. Obliterate all markings of a permanently closed heliport, FATO, or TLOF. If it is impractical to obliterate markings, place a yellow “X” over the “H” as illustrated in Figure 2–27. Make the yellow “X” large enough to ensure early pilot recognition that the heliport is closed. Remove the wind cone(s) and other visual indications of an active heliport.
Figure 2-27 · page 60Picture of the page from the copy saved here
j. Marking sizes. See Appendix C for guidance on the proportions of painted numbers.
Marking a Closed Heliport:
General Aviation
Figure 2–27. Marking a Closed Heliport: General Aviation
216. Heliport lighting. If the heliport operator intends for the facility to support night operations, light it with FATO and/or TLOF perimeter lights as described below. Design flush light fixtures and installation methods to support point loads of the design helicopter transmitted through a skid or wheel.
Chapter 2. General Aviation Heliports › 216. Heliport lighting.
a. TLOF perimeter lights. Use flush green lights meeting the requirements of FAA Airports Engineering Brief 87, Heliport Perimeter Light for Visual Meteorological Conditions (VMC), to define the TLOF perimeter. Use a minimum of. As an option at PPR facilities, use three light fixtures per side of a square or rectangular TLOF. Locate a light at each corner, with additional lights uniformly spaced between the corner lights. Using an odd number of lights on each side will place lights along the centerline of the approach. Define a circular TLOF using an even number of lights, with a minimum of eight, uniformly spaced. Space the lights at a maximum of 25 feet (7.6 m). Locate flush lights within 1 foot (30 cm) inside or outside of the TLOF perimeter.
(1) Raised TLOF perimeter lights. As an option, use raised, omnidirectional lights meeting the requirements of EB 87. Locate them on the outside edge of the TLOF or the outer edge of the safety net, as shown in Figure 2–28. Lighting on the outer edge of the safety net provides better visual cues to pilots at a distance from the heliport since it outlines a larger area. Make sure the raised lights do not penetrate a horizontal plane at the FATO elevation by more than 2 inches (5 cm). See Figure 7–3.
Elevated TL
OF
– Perimeter Lighting: Gene
ral Aviation
Figure 2–28. Elevated TLOF – Perimeter Lighting: General Aviation
Figure 2-28 · page 61Picture of the page from the copy saved here
(2) PPR facilities. Use flush lights for PPR heliports. As an option if only the TLOF is load bearing, use raised omnidirectional lights. Locate the raised lights outside and within 10 feet (3 m) of the edge of the TLOF. Make sure the lights do not penetrate a horizontal plane at the TLOF elevation by more than 2 inches (5 cm). As an option when the pavement or structure is larger than the TLOF, mount perimeter lights on the outer edge of the pavement or structure or the inner or outer edge of the safety net.
b. Load-bearing FATO perimeter lights. Green lights meeting the requirements of EB 87 define the perimeter of a load bearing FATO. Do not light the FATO perimeter if any portion of the FATO is not a load-bearing surface. Use a minimum of four. As an option at PPR facilities, use a minimum of three flush or raised light fixtures per side of a square or rectangular FATO. Locate a light at each corner, with additional lights uniformly spaced between the corner lights. Using an odd number of lights on each side will place lights along the centerline of the approach. To define a circular FATO, use an even number of lights, with a minimum of eight, uniformly spaced. Space lights at a maximum of 25 feet (7.6 m). Locate flush lights within 1 foot (30 cm) inside or outside of the FATO perimeter (See Figure 2–29). As an option, use a square or rectangular pattern of FATO perimeter lights even if the TLOF is circular.
Figure 2-29 · page 63Picture of the page from the copy saved here
At a distance during nighttime operations, a square or rectangular pattern of FATO perimeter lights provides the pilot with better visual alignment cues than a circular pattern, but a circular pattern may be more effective in an urban environment. In the case of an elevated FATO with a safety net, mount the perimeter lights a similar manner as discussed in paragraph 215.a(1). As an option, locate raised FATO perimeter lights, no more than 8 inches (20 cm) high, 10 feet (3 m) from the FATO perimeter. (See Figure 2–30. When a heliport on an airport is sited near a taxiway, there may be a concern that a pilot may confuse the green taxiway centerline lights with the FATO perimeter lights. As an option in such cases, use yellow lights as an alternative color for marking the FATO.
Figure 2-30 · page 64Picture of the page from the copy saved here
c. Floodlights. The FAA has not evaluated floodlights for effectiveness in visual acquisition of a heliport. However, if ambient light does not adequately illuminate markings for night operations, use floodlights to illuminate the TLOF, the FATO, and/or the parking area. If possible, mount these floodlights on adjacent buildings to eliminate the need for tall poles. Take care, however, to place floodlights clear of the TLOF, the FATO, the safety area, and the approach/departure surfaces, and transitional surfaces and ensure floodlights and their associated hardware do not constitute an obstruction hazard. Aim floodlights down to provide adequate illumination on the surface. Make sure floodlights that might interfere with pilot vision during takeoff and landings are capable of being turned off by pilot control or at pilot request.
Continue reading ↓ 120 of 319 passages shown