Radar Vectors
Advisory Circular Cancelled Issued Jan 20, 1994 AAS-100 123 pages Copy saved Nov 18, 2026

AC 150/5390-2A Heliport Design

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (65 of 123 pages). Check the original, as some words may be misread.

Advisory U.S. Department of Transportation Circular Federal Aviation Administration

Subject: HELIPORT DESIGN

1. PURPOSE. This Advisory Circular (AC) provides recommendations and standards for heliport and helistop design initiated after the date of this AC.

2. CANCELLATION. AC 150/5390-2, Heliport Design, dated January 4, 1988, is canceled.

3. EXECUTIVE SUMMARY. The modern helicopter is one of the most versatile transportation vehicles known to man. The helicopters ability to operate from minimal real estate has given it the capability of providing a wide variety of important services to any community which integrates the helicopter into its local transportation system.

a. Service. In addition to their service in the transportation of people, helicopters have proven to be useful to their communities in the following ways:

(1) Disaster Relief. Natural disasters often result in the breakdown of ground transportation systems. Helicopters are able both to bring in response teams and supplies and to evacuate injured people during the critical period before and while ground transportation is being restored.

(2) Air Ambulance Services. For an injured or critically ill person, time is life. Only helicopters can provide high speed point-to-point transportation without being constrained by the limitations of the ground infrastructure.

(3) Police Departments. Many municipalities consider their police department helicopters vital force multipliers in carrying out search and rescue, chase, and surveillance.

Date: 1/20/94 AC No: 150/5390-2A Initiated by: AAS-110 Change:

(4) Moving High Value Assets. High-value or time-sensitive cargo, such as canceled checks, and people, including the President of the United States, frequently travel on helicopters because this mode of transportation is fast and flexible. Companies use helicopters as an invaluable part of an in-house transportation system to connect the office with various plants, job sites, and the local airport. Utility companies use helicopters to construct and inspect high-voltage electrical lines and to monitor underground gas transmission lines. Newspapers and radio/TV stations use helicopters for on-site news gathering, taking photos, and airborne reporting of rush hour traffic conditions.

b. Facilities. The most effective way for a community to realize the benefits of helicopter services is by developing or permitting the development of places where helicopters can land and takeoff. While heliports can be large and elaborate, most are not. In many situations, a wind sock on a grass area with clear approaches is sufficient to provide an effective and safe heliport. This minimal facility may be adequate as a private use heliport, and may even suffice as the initial phase in the development of a public use heliport capable of serving the general aviation segment of the helicopter community.

c. Planning. While the heliport itself may be simple, the planning and organization required to properly put one into place can be intimidating. To help make the process easier, the Federal Aviation Administration has published this AC 150/5390-2A, Heliport Design. While the AC is a technical document intended to help engineers, architects, and city planners design, locate, and build the most effective heliport, it can be used by anyone considering the construction of a heliport.

AC 150/5390-2A 1/20/94

d. Location. The optimum location for a heliport is in close proximity to the desired origination and/or destination of the potential users. Industrial, commercial, and business operations in urban locations are demand generators for helicopter services, yet in many cases compete for the limited ground space available. A site permitting the aeronautical and commercial usage to be shared is a viable alternative to non-aeronautical use alone. Heliport sites may be adjacent to a river or a lake, a railroad, a freeway, or a highway, all of which offer the potential for multifunctional land usage. These locations also have the advantage of relatively unobstructed airspace which can be further protected from unwanted encroachment by properly enacted zoning. As vertical lift transportation becomes more and more prevalent, requirements for scheduled "airline type" passenger services will necessitate the development of an instrument procedure to permit "all-weather" service. This requirement may materialize at a few metropolitan heliports.

e. AC Organization. The AC is structured to provide communities and or persons intending to develop a heliport, or become involved in regulating helicopter facilities, with general guidance on heliport requirements. The AC is organized to minimize the amount of material that the reader is obligated to digest in order to have an understanding of heliport design based on the functional role the heliport is intended to perform.

(1) A heliport proponent should be familiar with the terminology used in this specialized field. Chapter 1 defines pertinent terms used in the industry and identifies actions common to developing a heliport.

(2) Private use heliports are usually owned by an individual or corporation who can control heliport usage. Generally, a private use heliport is used by a single pilot or a small number of pilots who are familiar with the heliport and any physical or operational limitations. For this reason, private use heliports can be designed to more flexible standards. Design recommendations relevant to developing a private use heliport are found in chapter 2.

(3) Public use general aviation heliports are normally publicly owned although they can be privately owned. As public use facilities, they can be used by any qualified pilot. Therefore, the recommended dimensions and clearances are more demanding than for private use heliports. Design standards relevant to developing a public use general aviation heliport are found in chapter 3.

(4) Transport heliports are developed to provide the community with a full range of vertical flight services including scheduled service by air carriers (airlines) using helicopters. When the heliport serves any scheduled or unscheduled passenger operation of an air carrier that is conducted with an aircraft having a seating capacity of more than 30 passengers, the heliport is required to be certificated by the FAA in accordance with Federal Aviation Regulation (FAR) Part 139, Certification and Operations: Land Airports Serving Certain Air Carriers. In any event, a transport heliport would also accommodate corporate users and local air taxi operators. This broad spectrum of activities frequently requires a more extensive air-side and land-side infrastructure with the potential capability to operate in instrument meteorological conditions. Not withstanding these requirements, a community's investment in a heliport may be substantially less than the investment required for an airport providing comparable services. Design standards relevant to developing a transport heliport are found in chapter 4.

(5) Hospital heliports are treated as special cases of private use facilities providing a unique public service. They are normally located in close proximity to the hospital emergency room or a medical facility. Design standards relevant to developing a hospital heliport are found in chapter 5.

(6) When there is a significant number of helicopter operations on an airport, it may be prudent to consider developing separate facilities specifically for helicopter use. Chapter 6 addresses helicopter facilities on airports.

(7) Currently, when the weather is poor, helicopters tend to use an airport with an instrument landing procedure. Good planning suggests municipalities should plan for the eventual development of instrument approaches to their heliports. Recommendations to be considered in contemplating future instrument operations at a heliport are found in chapters 7 and 8.

(8) Chapter 9 addresses heliport gradients and pavement design issues.

(9) The appendices provide helicopter dimensional data, dimensional recommendations for heliport markings, and addresses of aviation organizations.

ii

4. APPLICATION. The recommendations and standards in this AC are for planning and designing civil heliports. These recommendations and standards are predicated on average conditions, thus may require adaptation to meet the specific conditions of a particular site. To the extent that it is feasible and practical to do so, these standards should be used in planning and designing improvements to an existing heliport when significant expansion or reconstruction is undertaken. Conformity with these standards is prerequisite to Federal grant-in-aid assistance. The recommendation and standards in this AC are not intended to govern either helicopter or heliport operations or be used to design an instrument approach procedure.

LEONARD E. MUDD Director, Office of Airport Safety and Standards

iii

v

AC 150/5390-2A 1/20/94

vi

vii

AC 150/5390-2A 1/20/94

viii

CHAPTER 1. INTRODUCTION

CHAPTER 1. INTRODUCTION

1. GENERAL. This chapter defines terms used in this Advisory Circular (AC), and addresses matters of a general nature relating to heliport development.

2. BASIS. This AC implements the objective set forth in Section 103 of the Federal Aviation Act of 1958 as amended. That states, in part:

"In the exercise and performance of his power and duties under this Act, the Secretary of Transportation shall consider the following, among other things, as being in the public interest:

(a) The regulation of air commerce in such manner as to best promote its development and safety and fulfill the requirements of defense;

(b) The promotion, encouragement, and development of civil aeronautics;

(c) The control of the use of the navigable airspace of the United States and the regulation of both civil and military operations in such airspace in the interest of the safety and efficiency of both."

This AC recognizes that FAR Part 77, Objects Affecting Navigable Airspace, establishes standards for determining obstructions to navigable airspace and provides for aeronautical studies of such obstructions to determine their effect on the safe and efficient use of airspace. These standards apply to the effect of construction proposals upon a heliport available for public use or a planned or proposed heliport that will be available for public use. The heliport primary surface described in FAR Part 77 coincides in size and shape with the designated takeoff and landing area, i.e., the FATO. The heliport approach and transitional surfaces described in FAR Part 77 are depicted in figure 1-6. Public agencies are encouraged to enact zoning ordinances to prevent man-made features from penetrating these surfaces.

3. EXPLANATION OF TERMS. The Pilot/Controller Glossary of the Airman's Information Manual (AIM) defines terms used in the Air Traffic Control system such as instrument flight rules (IFR), and visual flight rules (VFR). Copies of the AIM are available from the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402. Other terms used in this publication follow:

\a. Approach/Takeoff Path. The flight track helicopters follow when landing at or taking off from a heliport.

b. Design Helicopter. A generic rotorcraft which reflects the maximum weight, overall length, rotor diameter, etc. of all helicopters expected to operate at the heliport.

c. Emergency Evacuation Facility. A clear area on a roof of a tall building, that is not intended to function as a heliport, yet is capable of accommodating helicopters engaged in fire fighting and/or emergency evacuation operations.

d. Final Approach and Takeoff Area (FATO). A defined area over which the final phase of the approach to a hover, or a landing, is completed and from which the takeoff is initiated. This area was called the "takeoff and landing area" in previous publications.

e. Final Approach Reference Area (FARA). A 150 foot (45 m) wide by at least 150 foot (45 m) long obstacle-free area with its center aligned on the final approach course. It is located at the end of a precision instrument FATO.

f. Hazard to Air Navigation. Any object having a substantial adverse effect upon the safe and efficient use of the navigable airspace by aircraft or upon the operation of an air navigation facility.

NOTE: Obstructions to air navigation are presumed to be hazards to air navigation until an FAA study determines otherwise.

g. Heliport. The area of land, water, or structure used or intended to be used for the landing and takeoff of helicopters, together with appurtenant buildings and facilities.

h. Heliport Elevation. The elevation, expressed as the distance above mean sea level, of the highest point in the FATO or the FARA.

i. Heliport Imaginary Surfaces. The imaginary planes, centered about the FATO and the approach/takeoff path, that identify the objects to be evaluated to determine whether the objects should be removed, lowered, and/or marked and lighted--or the approach/takeoff path realigned.

AC 150/5390-2A 1/20/94

j. Heliport Reference Point (HRP). The geographic position of the heliport expressed as the latitude and longitude at:

(1) The center of the FATO, or the centroid of multiple FATOs, for heliports having visual and nonprecision instrument approach procedures; or

(2) The center of the FARA when the heliport has a precision instrument procedure.

k. Helistop. A minimally developed helicopter facility for boarding and discharging passengers or cargo. The heliport--helistop relationship is comparable to a bus terminal--bus stop relationship with respect to the extent of services provided or expected.

NOTE: The heliport design recommendations and standards in this AC are equally applicable to helistops.

l. Hospital Heliport. A heliport limited to serving helicopters engaged in air ambulance, or other hospital related functions.

m. Medical Emergency Site. An unprepared site at or near the scene of an accident or similar medical emergency on which a helicopter may land to pick up a patient in order to provide emergency medical transport.

NOTE: A designated helicopter landing area located at a hospital or medical facility is a heliport and not a medical emergency site.

n. Obstruction. Any object, including a parked helicopter, exceeding the obstruction standards specified by FAR Part 77, Objects Affecting Navigable Airspace, Subpart C, Obstruction Standards.

o. Private Use Heliport. A heliport developed for the exclusive use of the owner and persons authorized by the owner.

p. Protection Zone. An area off the end of the FATO and under the approach/takeoff path to enhance the protection of people and property on the ground.

q. Public Use Heliport. A heliport available for use by the general public without a requirement for prior approval of the owner or operator.

(1) General Aviation Heliport. A heliport intended to accommodate individuals, corporations, and helicopter air taxi operators. Scheduled passenger services may be available.

(2) Transport Heliport. A heliport intended to accommodate air carrier operators providing scheduled or unscheduled service with large helicopters.

r. Safety Area. A defined area on a heliport surrounding the FATO which is free of objects, other than those required for air navigation purposes, and intended to reduce the risk of damage to helicopters accidentally diverging from the FATO.

s. Taxi Route. An obstruction free corridor in which helicopters hover taxi above the surface at airspeeds less than approximately 20 knots.

t. Taxiway. A defined path established for the ground taxi of helicopters from one part of a heliport to another.

u. Touchdown and Liftoff Area (TLOF). A load bearing, generally paved area, normally centered in the FATO, on which the helicopter lands or takes off. The TLOF is frequently called a helipad or helideck. This area was called the "FATO" in previous publications.

4. NOTICE OF HELIPORT DEVELOPMENT. Except as noted in subparagraph b, FAR Part 157, Notice of Construction, Alteration, Activation, and Deactivation of Airports, requires any person proposing to construct, activate, or deactivate a heliport to provide the FAA advance notice of their intent. Notice is also required when an existing heliport changes the size/number of FATOs; adds, deletes, or modifies an approach or departure route; or changes its status from private use to public use or public use to private use. States and local governments may have notice requirements that parallel the Federal requirement. Heliport proponents are urged to contact their appropriate state and local governmental offices or transportation departments for their requirements.

a. Notification Procedures. Notification is accomplished by forwarding a completed FAA Form 7480-1 (figure 1-1), a location map (figure 1-2), and a layout sketch (figure 1-3) to the appropriate FAA Regional Airports Office. Airspace submissions should be made at least 90 days prior to construction, alteration, or date of changed use begins. Addresses for FAA Regional Airports Offices are on the Form. It is recommended that a 7.5 Minute U.S. Geological Survey (USGS) Quadrangle Map be used for the location map. The sketch should show the heliport layout, all proposed approach (departure) routes, buildings, trees, fences, power lines, etc.

NOTE: (1) In an emergency involving essential public service, public health, public safety, or when the delay arising from the 90 day advance notice requirement would result in an unreasonable hardship, a proponent may provide notice to the appropriate FAA Airport District/Field Office or Regional Office by telephone or other expeditious means as soon as practicable in lieu of submitting FAA Form 7480-1. However, the proponent shall provide full notice, through submission of FAA Form 7480-1, when otherwise requested or required by the FAA.

(2) The latitude and longitude of the proposed heliport should be stated in North American Datum of 1983 (NAD-83) coordinates. If another datum series is used, that fact should be noted in the submission.

b. Notice Exemptions. Paragraph 157.1, Applicability, of FAR Part 157 exempts heliports meeting the conditions under (1), (2), and (3) below from the requirement to submit notice. However, these exemptions do not negate a notice or formal approval requirement prescribed by state law or local ordinance.

(1) Any heliport subject to conditions of a Federal agreement that requires an approved current layout plan to be on file with the FAA.

(2) A heliport at which flight operations will be conducted under visual flight rules (VFR) and which is used or intended to be used for a period of less than 30 consecutive days with no more than 10 operations per day.

(3) The intermittent use of a site that is not an established airport, which is used or intended to be used for less than one year and at which flight operations will be conducted only under VFR. For the purpose of this part, "intermittent use of a site" means: (1) the site is used or is intended to be used for no more than 3 days in any one week; and (2) no more than 10 operations will be conducted in any one day at that site."

NOTE: For the purposes of applying the FAR Part 157 exemption criteria cited in (2) and (3) above, a landing and associated takeoff is considered to be one operation.

c. FAA Action. The FAA evaluates the proposed heliport for its impact upon the safe and efficient use of navigable airspace; for its impact upon the operation of air navigation facilities; and for its effect on the safety of persons and property on the ground. The proponent is advised of the FAA findings.

d. Notice Benefits. In order for the FAA to study the impact of off-site construction (Refer to paragraph 7) upon a heliport available for public use, it is essential that the heliport's latitude and longitude, elevation, and the direction and type of approach and departure be on record with the FAA.

5. MEDICAL EMERGENCY SITES. Medical emergency sites are clear and level areas at or near the scene of an accident or incident that have been selected or designated by the local emergency response team as the place where the helicopter air ambulance is directed to land in order to transport an injured person to a hospital.

a. Notice. Because of their transitory nature, medical emergency sites are not heliports and submission of FAA Form 7480-1 is not required. Proponents of predesignated emergency landing sites should coordinate their emergency plan with the local airport traffic control tower (ATCT). This coordination is especially important if a site(s) may be used under conditions of low visibility and/or use of the site(s) would require ATC clearance.

b. Marking/Lighting. Depending upon the level of training of the local accident or emergency response teams and agreements worked out with the local air ambulance operators, medical emergency landing sites may be identified with flags, markers, lights, flares, etc.

c. Landing Discretion. All landings at a medical emergency site are made at the pilot's discretion after weighing the urgency for air transport against the performance capability of the helicopter, his or her piloting ability and experience, and the limitations and/or constraints of the site.

6. EMERGENCY EVACUATION FACILITIES. To facilitate fire fighting or emergency evacuation operations, local building codes may require structures over a specified height to provide a clear area on the roof capable of accommodating a helicopter. Since the cleared area is not intended to function as a heliport, there is no requirement to submit an FAA Form 7480-1. As in the case of medical emergency sites, proponents of emergency evacuation facilities should advise the local ATCT of the facility. The landing surface should be developed to the local fire department requirements based on the size and weight of the helicopter(s) expected to engage in fire or rescue operations. The following markings are recommended to identify the limits of the landing area and to alert the pilot to any weight limitation. Markings should be in a color (red or orange is suggested) that provides the greatest possible contrast to the roof coloration.

AC 150/5390-2A 1/20/94

a. Edge Marking. A 12 inch (30 cm) wide line defines the limits of the intended landing surface. It is recommended that the edge marking provide at least 10 feet (3 m) of clearance to any object that could be struck by a helicopter's main or tail rotor.

b. Weight Limitation. Any limitation on allowable weight should be placed in the center of the circle as viewed from the preferred direction of approach. Weight limitations should be stated in units of 1,000 pound as illustrated in figure 1-4. To assure early recognition of a weight limit it is suggested that the numeral(s) be a minimum of 3 feet (0.9 m) in height. A bar may be placed under the number to minimize the possibility of being misread.

7. NOTICE OF PROPOSED CONSTRUCTION. FAR Part 77 requires the FAA be notified of certain proposed construction or alteration of a structure or object. It also specifies standards for determining obstructions to air navigation and provides for FAA aeronautical studies of obstructions to determine their effect on the safe and efficient use of airspace.

a. Notice. Proposed construction or alteration of structures or objects in the vicinity of a public use heliport requiring notice to the FAA include those which are:

(1) more than 200 feet AGL or

(2) less than 200 feet AGL and;

(a) are located within 5,000 feet (1 500 m) of a public use or military heliport and penetrate a 25:1 sloping surface originating at the heliport as illustrated in figure 1-5, or

(b) the FAA requests notice.

b. FAA Aeronautical Study. Information on the FAA's role in conducting an aeronautical study of off heliport construction is found in AC 70/7460-2, Proposed Construction or Alteration of Objects That May Affect the Navigable Airspace. The FAA also may choose to study a proposed structure that the FAA believes may pose a hazard to navigation. In most cases, wires and their supporting structures fall into this discretionary category of structures less than 200 feet AGL.

c. Determination. The FAA summarizes the findings of an aeronautical study in a determination of hazard or no hazard that is issued to the sponsor. An FAA determination discusses the aeronautical impact of the proposed construction or alteration on the use of

navigable airspace. The FAA does not have authority to approve or disapprove the construction of a proposed structure that would be a possible hazard to air navigation, but FAA's recommendations on the subject are not easily dismissed by project sponsors because of potential liability.

(1) An FAA marking-and-lighting recommendation may be incorporated into a determination of no hazard and, if included, is considered to be a condition to that determination.

(2) The FAA also provides copies of determinations to state and local aviation agencies and airport authorities.

(3) When the study involves a proposal for which a Federal Communications Commission (FCC) construction permit is required, then the FAA provides the FCC with a copy of the determination.

8. FAA STUDY OF EXISTING OBJECTS. Existing objects that are obstructions to air navigation are presumed to be hazards until an FAA study determines otherwise.

a. FAA Study. Aeronautical studies of existing objects are conducted when deemed necessary by the FAA to determine the physical and electromagnetic effect on the use of navigable airspace and air navigational facilities. Aeronautical studies of existing objects may be initiated as a result of information received or a situation observed.

b. Mitigating Adverse Effects. The adverse effect of an object presumed or determined to be a hazard to air navigation may be mitigated by:

(1) Removing the object, if practical;

(2) Marking and/or lighting the object, provided an FAA aeronautical study has determined that the object would not be a hazard to air navigation if it were marked and lighted;

(3) Realigning the approach/takeoff path to avoid the object; or

(4) Modification of operations.

9. FEDERAL ASSISTANCE. The FAA administers a grant program that provides financial assistance to eligible sponsors to develop a public use heliport. Information on Federal-aid program eligibility requirements is available in FAA Regional and District Airports Offices. Addresses of Regional offices are listed in Appendix 3. AC 150/5000-3, Address List for Regional Airports Divisions and Airports District/Field Offices, lists all addresses.

10. ENVIRONMENTAL ASSESSMENTS. The National Environmental Policy Act of 1969 requires an environmental assessment be made prior to undertaking certain Federal actions relating to heliport development. Actions which may require an environmental assessment are normally associated with Federal grants or heliport layout plan approvals leading to the construction of a new heliport or significant expansion of an existing heliport.

a. Assessment Items. An environmental assessment must address noise, land usage, water and air quality, socio-economic issues, and viable alternatives to the proposed development, etc. It must also describe the action taken to ensure public involvement and citizen participation in the planning process. An opportunity for a public hearing may be required for a federally funded development of, or significant improvement to, an existing heliport.

b. Guidance. FAA Order 5050.4A, Airport Environmental Handbook, and Order 1050.1, Policies and Procedures for Considering Environmental Impacts, provide guidance on environmental assessments. State and local governments should be contacted directly as they may also require an environmental report. The procedures in AC 150/5020­ 1, Noise Control and Compatibility Planning for Airports, describe a means of assessing the noise impact for airports which can be used in conjunction with the Heliport Noise Model (HNM) for assessing noise impact. The HNM is available from the FAA Office of Environment and Energy. Proponents of non-federally assisted heliports are encouraged to work closely with local governmental authorities concerning environmental issues.

c. Turbulence. Air flowing around and over buildings, stands of trees, terrain irregularities, etc. can create turbulence which may affect helicopter operations. A report, Evaluating Wind Flow Around Buildings on Heliport Placement. addresses winds effect on helicopter operations. A copy of the report (Accession number is AD-A153512) is available from the National Technical Information Service, Springfield, Virginia 22161. The following actions

may be taken in selecting a site to minimize the effects of turbulence.

(1) Ground Level Heliports. Helicopter operations from sites immediately adjacent to buildings, trees, etc. are subjected to air turbulence effects caused by such features. Therefore, locate the landing and takeoff area as far from nearby buildings, trees, or significant terrain features as the site permits.

(2) Elevated Heliports. Elevating heliports 6 feet (1.8 m) or more above the level of the roof will generally minimize the turbulent effect of air flowing over the roof edge. While elevating the platform helps reduce or eliminate the air turbulence effects, a safety net/shelf may be required.

11. STATE ROLE. Many state departments of transportation, aeronautical commissions, or similar authorities, require prior approval, and in some instances a license, for the establishment and operation of a heliport. Several states administer a financial assistance program similar to the Federal program and are staffed to provide technical advice. Heliport proponents are encouraged to contact their respective state aeronautics commissions or departments for particulars on licensing and assistance programs. Appendix 3 lists addresses for state aviation offices.

12. LOCAL ROLE. Some communities have enacted zoning laws, building codes, fire regulations, etc. that can impact heliport establishment and operation. Some have or are in the process of developing codes or ordinances regulating environmental issues such as noise and air pollution. A few localities have enacted specific rules governing the establishment of a heliport. Therefore, heliport proponents are encouraged to make early contact with officials or agencies representing the local zoning board, the fire, police, or sheriff's department, and the elected person(s) who represent the area where the heliport is to be located.

AC 150/5390-2A

J. auRvE Compary

Estab ahmanc or Aclivaliça AhtHicn à. Loendón orLandng Arep

Alenandris, Virginia

Hel1-Alex B. Purpose TipeUu P C

C. O Lenuding reas

t. Obstructons

Hasenic Teple 430 Halio Touer 200 Hi-Rise Apartments 150 Maxkod Pouer Li:e 75 Cffice Bulidings 120

G 0tr Coifalions

Muary 5ch Jeffersor-Houston Sch RcSerl E Lee Sch Curan Sch Stonewsl1 Jackson Sch Rishop Ireton High Sch

1/20/94

NOTICE OF LANDING AREA PROPOSAL

NOTICE OF LANDING AREA PROPOSAL

INa. Ainpar. Cry. Shte. 2p Codal 300 Duke Street Alexandzia, Virginia 23003

C Ueuigh:Fligfert Other (Specrly)

3. Ciru-hb bnd Cincci-on From Nct applicable . L 6. Landtude J. ERTHO 3B 46′:06 10 10 1.5

i Chu ar Aanb, Certy Curg EL CHibor 0cL.193 Har'y4

D. Lending Ayn Dpa Propc4d Dit Any t Pwy y 43 AMY Undro fr Megrene Beuing cl Rurwsy) or M HNB 3.5 10

inFL

Typa or Furrwts: Sundce (Circrdte. Aspha Turd, Etc.I Oimansond d Fhad Aporoac. Lnc 100 x 200

Dinmnonsiong of Touchdowr and Li-OH AsH TLOF; Ir FHN 50 x 50

FEdH 1C3/306

Typa ar Sunfice Conccete AI , , r, .] ME 0.5 Doriptknof Liphing (/any: Ciroctior of Presiling Wird 0.3 -Edge E Landing Dircction NorthArly 55 D.E F. u D s 0.05 1. Emuad or Aue Nurba- Buad Arcrt 0.1 HHFH

0 2 U 5

drdcn 2 JAwwnige Humber Lorahy Larings Fron Fron Landing H N 0.9 M HHOW 20 E 50 ME 0.8 E 0.94 1 0.9 H 4 0.1 H Apploeion Ier Rmperl Lhowwing 0.3

Fesidercen lall direction)

Coumty surla

Sepnatuns (nh wnk)

Ail 1, 1993 222-267-2763

FAA Fom 8-1 1-c: Sucarade F-troE Catior

Figure 1-1. Example of required notice

NORTH

SCALE 1 24000

1000 620

Figure 1-2. Example of a beliport location map

AC 150/5390-2A

FRUCHT AVENUE

AUTO PARKING

CITY PRÓPERTY OFFICE CITY PROPERTY FUTURE PAVED APRON Figure 1-3. Example of a helipon layout sketch APPROACII/TAKEOFF PATH LEAD-IN LIGHTS IN-GROUND FATO EDGE MARKERS TLOF APPROACH/TAKEOFF PATH

EDGE LIGHTS

EDGE LIGHTS

PROFRRTY LINE

1/20/94

WEIGHIT LIMITATION (1, 000 Pound Units) ROOF SURFACE SHOULD BE FREE OF LOOSE GRAVEL

RED/ORANGE PAINTED CIŘCLE SLIGHTLY RAISED PLATFORM

FLAG USED AS CAUTION HELICOPTER LANDINO AREA AUTHORIZED PERSONNEL DNCY WIND INDICATOR TERCE

Figure 1-4. Emergency evacuaion faciliry

RED/ORANGE PAINTED CIŘCLE SLIGHTLY RAISED PLATFORM

(00 m)

5,000°( 500 m)

Figure 1-5. Off site development rcquiring notice Antenna les thaa 200 feet (80 m) in height (Notiee required by FAR 77.13(n)(1).) which penetratcs the 25:1 surface. but top will penetrale the 25;1 surface. [Notice is required by FAR 77,13(a)(2)(ii).1 Antenna is over 200 feet. (60 m) in height. Buildíog ie tost than 200 feet (60 m) in height

[Notice requirud by FAR 77.13(a)(2)(ii).]

Conatruotion crane penetratee 25:1 surface. [Notice is required by FAR 77.13(a)(2X(ii).]

Building less than 200 feet (60 n) in height does not penetrate 25:1; aurface. (Notice is not roquired.†

Buikling ie more than 6,0ã0 feet from leliport. [Notice ie required if building wutld be 200 fet (60 m) or more in heighi.]

AC 150/5390-2A

LANDING AND TAKEOFT AREA PRIMARY SURFACE FATO

LANDING AND TAKEOFT AREA PRIMARY SURFACE FATO

1/20/94

1/20/94

Hedipor?? Primuzy Sre (FATO:

ISOMETRIC VIEW

* FRIMARY SURFACE: 200775 π74X X VARIABLE MINIMUM 1.S OVERALL LENGTII)

Heliport Translional Srface (Spe21

Halipor pproach Euríac Səpa 8:1) Helipert Trabsitonnl Surfare (Sloge 2:1)

* FRIMARY SURFACE: 200775 π74X X VARIABLE MINIMUM 1.S OVERALL LENGTII)

4,000' (1 200 m)

Helipot Appro Surace (Siape 6.1) Ground Leve:

PLAN VIEW

Figure 1-6. Obstruction identification surfaces for visual operalioas

AC 150/5390-2A

50H' (150m)

CHAPTER 2. PRIVATE USE HELIPORTS

13. GENERAL. Helicopters are routinely used for public services such as news gathering, traffic reports, and law enforcement. Numerous firms transport oil field workers from their on-shore heliports to offshore oil platforms saving hours of transit time over shipbased transportation systems. Companies have found the helicopter to be an efficient and effective way to transport people and products between headquarters offices and suburban manufacturing plants, to remote or inaccessible field/mine sites, as well as a convenient shuttle to/from the local airport. To save time and avoid the congestion on streets and highways, an increasing numbers of helicopter owners are finding the helicopter to be a convenient way of commuting between their homes and their places of business. With this diverse usage, private use heliports can vary considerably in both size and complexity. This chapter contains recommendations for designing a heliport intended to be used as a private use facility. Figure 2-1 identifies the essential features of a private use heliport while figure 2-2 depicts an extremely large private use heliport.

CHAPTER 2. PRIVATE USE HELIPORTS

14. FINAL APPROACH AND TAKEOFF AREA (FATO). A private use heliport should have an identifiable, object free area (FATO) available for helicopter landings and takeoffs.

a. Location. A FATO may be at ground or water level, or at pier or roof top level. Objects or structures should be outside the FATO to permit at least one clear approach/takeoff path aligned with the prevailing winds. Figure 2-1 illustrates this recommendation. Heliports located on raised platforms, piers and docks, or buildings may have outer portions of the FATO extend beyond the platform, pier, dock, or building edge as illustrated in figure 2-4.

b. Size. A FATO may have any shape provided that its least dimension, i.e., length, width, or diameter, is not less than 1.5 times the overall length of the design helicopter.

c. Gradients. When a TLOF is not provided, the FATO should be graded to provide a smooth surface. To assure drainage, a 0.5 to 2 percent gradient is suggested for any part of a FATO surface on which a helicopter is expected to land.

15. SAFETY AREA. A safety area surrounds the FATO. Its recommended width is 1/3 rotor diameter of the design helicopter, but not less than 10 feet (3 m).

The FATO and the safety area should be free of objects such as other helicopters, buildings, fences, parapets, etc., which could be struck by the main or tail rotor, or be hit by the skids of a helicopter while landing or taking- off.

16. TOUCHDOWN AND LIFT-OFF AREA (TLOF). When the entire FATO is not load bearing, a paved or an aggregate-turf TLOF is recommended.

a. Location. When a TLOF is provided, it is normally centered within the FATO. For irregularly shaped or oversized FATOs, the center of the paved or aggregate-turf TLOF should be located at least 3/4 of the design helicopter's overall length in from the FATO boundaries. Figure 2-3 illustrates the recommended FATO/TLOF relationship. To the extent practical, the TLOF of a roof top heliport should be elevated above the level of any obstacle in the FATO.

b. Size. The least dimension of a TLOF should be a minimum of 1.5 times the length or width of the undercarriage of the design helicopter, whichever is greater.

c. Surface Characteristics. If a surface more durable than aggregate-turf is needed, Portland Cement Concrete (PCC) pavement is suggested. An asphaltic surface is "less desirable" for heliports as it may rut under the wheels or skids of a parked helicopter, a possible factor in some roll-over incidents. Pavements should have a broomed or other roughened finish that provides a skid resistant surface for helicopters and non- slippery footing for persons. Pavements should be designed to support 1.5 times the maximum takeoff weight of the design helicopter. Roof top heliport TLOFs may be constructed of wood, metal, or concrete.

d. Elevated TLOFs. Roof top heliport TLOFs may be constructed of wood, metal, or concrete. Elevator penthouses, cooling towers, exhaust/fresh air vents, and other raised features impact roof top helicopter operations. To the extent practical, the TLOF of a roof top heliport should be elevated above the level of any obstacle in the FATO. Other objects or structures should be outside the FATO to permit at least one clear approach/takeoff path aligned with the prevailing winds. Figure 2-4 illustrates this recommendation. Elevated platforms should be designed to support 1.5 times the maximum takeoff weight of the design helicopter. When the TLOF is on a platform elevated more than 30 inches

AC 150/5390-2A 1/20/94

(75 cm) above its surroundings, a 5 foot (1.5 m) wide safety net or shelf should be provided. The safety net or shelf should have a load carrying capability of 25 pounds per square foot (122 Kg per sq. m). The net or shelf, as illustrated in figure 2-4, should not project more than 2 inches (5 cm) above the level of the TLOF. A report, Structural Design Guidelines for Heliports, (Report Number AD-A148967) is available from the National Technical Information Service, Springfield, VA 22161.

e. Gradients. To assure drainage, TLOF gradients should range between 0.5 to 2.0 percent.

17. APPROACH/TAKEOFF SURFACE.

a. Approach/Takeoff Path. A private use heliport must have at least one approach/takeoff path. This path, to the extent practical, should be aligned with the dominate winds. Additional approach/takeoff paths are recommended. Approach/takeoff paths may curve to avoid objects and/or noise sensitive areas and utilize the airspace above public lands, e.g., freeways, rivers, etc.

b. Approach/Takeoff Surface. An approach/ takeoff surface is centered on each approach/takeoff path and should conform to the dimensions of the FAR Part 77 heliport approach surface. Figure 1-6 illustrates the FAR Part 77 approach surface which should be free of object penetrations.

18. HELICOPTER PARKING. A separate helicopter parking area is not required unless the heliport must accommodate more than one helicopter at a time. Parked helicopters should not penetrate an approach/takeoff surface or be parked within the safety area. While parking areas need not be paved, figure 2­ 2 depicts a large private use heliport with a number of paved parking pads. Figure 2-5 illustrates a simple parking apron with details of recessed eyes/loops permitting helicopters to be tied down.

19. HELIPORT MARKERS AND MARKINGS. Markers and/or surface markings are suggested to identify the facility as a heliport, the perimeters of the FATO and/or TLOF, and, if needed, the operational limitations on weight. Lines used as surface markings may be paint or preformed material.

a. Perimeter Markings. In-ground or surface markings may be used to define either, or both, the FATO and TLOF.

(1) Unpaved Surfaces. The perimeter of a turf FATO should be identified with in-ground markers

that will not catch helicopter skids or create barriers to helicopter maneuvering. If raised markers are used, they should be located at the outer edge of the safety area and no more than 8 inches (20 cm) in height. Markers are placed at the corners, and as needed along the edges of the FATO. Figure 2-6 illustrates different types of in- ground and raised markers.

(2) Paved Surfaces. A 12 inch (30 cm) wide dashed line, as illustrated in figures 2-5 and 2-7, defines the limits of the FATO when the entire surface is paved. A 12 inch (30 cm) wide solid line is used to define the limits of a TLOF. While white is the color most commonly used, any color which provides good contrast to the background, may be used.

b. Identification Marking. A distinctive marking, such as the company logo, serves to identify the facility as a private use heliport. The identification marking should be placed at the preferred touchdown location, be as large as practical and be oriented to be legible from the preferred direction of approach. The marking should be at least 10 feet (3 m) in height. The capital H illustrated in Appendix 2 may be used in lieu of a logo.

c. Weight Limitations. Surfaces which are limited in weight-carrying ability should be marked with a number, in thousands of pounds. The marking should be large enough to be legible from the approaching helicopter. The number is located to the right and below the heliport symbol as viewed from the preferred directions of approach.

d. Closed Heliport. All markings on a permanently closed heliport should be obliterated. When obliteration is impractical, a yellow X should be placed over the markings. The X marking, as illustrated in figure 2-8, must be large enough to ensure pilot recognition from 1/4 mile (400 m).

e. Parking Apron. If a parking apron is provided, it is recommended that it be designed and marked utilizing the guidance in paragraphs 30 and 31.

20. HELIPORT LIGHTING. When night operations are intended and ambient lighting is inadequate, it is recommended that the perimeter of the FATO or TLOF (but not both) be defined with yellow lights. Alternatively, floodlights may be used to illuminate the heliport's FATO or TLOF surfaces. Figures 2-9 and 2-10 illustrate the recommended perimeter lighting systems.

a. Perimeter Lights. At least 3 uniformly spaced lights are recommended per side of a square or rectangular FATO or TLOF with a light located at each corner. A minimum of eight lights are needed to define a circular FATO or TLOF. The interval between lights should not exceed 25 feet (7.5 m).

(1) FATOs. Flush lights may be located on, or within 1 foot (30 cm) of, the FATO edge. Raised light fixtures, modified to be no more than 8 inches (20 cm) in height, should be located 10 feet (3 m) out from the edge of the FATO.

(2) TLOFs. Flush lights may be located on, or within 1 foot (30 cm) of, the TLOF edge. Raised light fixtures, modified to be no more than 8 inches (20 cm) in height, may be located 10 feet (3 m) out from the TLOF edge and should not penetrate a horizontal plane at the TLOF's elevation by more than 2 inches (5 cm).

(3) Raised TLOFs. Flush lights should be within 1 foot (30 cm) of the edge of a raised TLOF. Raised fixtures should be within 1 foot (30 cm) of the TLOF edge and should not project more than 2 inches (5 cm) above the TOLF as illustration in figure 2-10. In snow areas, it is suggested that the lights be placed along the outer edge of the safety net or shelf.

b. Floodlights. When floodlighting is used, care should be taken to place floodlights clear of the safety area and the approach/takeoff surface(s). Floodlights should be aimed down so as not to interfere with pilot vision and provide a minimum of 3 foot candles (32 lux) of illumination over the FATO or TLOF surfaces. To eliminate the need for tall poles, floodlights may be mounted on adjacent buildings. Floodlights which might interfere with pilot vision during takeoff and landings must be capable of being turned off during landings and takeoffs.

21. WIND DIRECTION INDICATOR. A private use heliport must have at least one wind indicator. A wind sock is the preferred indicator as it shows both the direction and magnitude of the wind. The wind sock should be placed where it provides a true indication of surface wind and is clear of the safety area and any approach/takeoff surface. The wind sock may be internally or externally lighted for night operations, or, alternatively be located in an illuminated area.

22. HELIPORT SAFETY AND SECURITY.

a. Safety. Provisions should be made to prevent any spilled fuel from collecting in a confined location and/or contaminating a waterway. National Fire Protection Association pamphlets provide guidance on fuel handling and storage.

b. Security. The operational areas of a heliport need to be kept free of people, animals, and vehicles. The method to be used to control access depends upon the heliport location and type of potential intruder. In urban areas, a curb will normally keep vehicles from entering while in rural areas cattle guards or fences will prevent the entry of animals. Generally, people will not enter a fenced area. In all cases where a fence is used, it should be as low as possible and at the greatest possible distance from the safety area and not penetrate any approach/takeoff surface. A visible reminder such as a sign, a low trimmed hedge, or flower bed may suffice to alert people to the heliport presence where access to the heliport owners property is already controlled.

AC 150/5390-2A 1/20/94

APROP SLRRAOE

APROP SLRRAOE

CED

TVNOLLJ

Pigure 2-1. Essential features of a private use heliport

ATO

Figure 2-2. A large private use beliport

AC 150/5390-2A

TLOF B

B

FATO Figure 2-3. FATO/TLOF relationship C FATO PROTECTION ZONE

RECOMMENDED FATO/TLOF MINIMUM DIMENSIONS Based On The Design Helicopter

A-FINAL APPROACH AND TAKEOFF AREA (FATO) 1.6 x OVERALL LENGTII B-TOUCHDOWN AND LIFT-OFF AREA (TLOF) 1.5 × UNDERCARRIAGE LENGTH OR WIDTH NORMALLY CENTERED IN THE FATO C-SAFETY AREA 0.33 x ROTOR DIAMETER NOT LESS THAN 10 FEET (3 m)

1/20/94

¿IX3 D H ) )

Figure 2-4. Elevated TLOF and safery net

APPROACH/TAKROFF SURFACE

APPROACH/TAKROFF SURFACE

PAVED

AC 150/5390-2A

PAVED

TAXIWAY CENTERLINE

Figure 2-5. Helicopter parking LIGHTED SOCK WIND

FATO

SAFETY AREA

APPROACH/TAKEOFF SUHFACE

PARKING APRON

APRON PAVEMENT

RECESSED-TIE DOWNS 1/20/94

ABOVE GROUND MARKERS

ABOVE GROUND MARKERS (Low Fenco, Embudded Rocka) [10 Feet (3 m) from FATO Edge]

WIND SOCK

WIND SOCK

1/20/94

APPROACH/TAKEOFF SURFACE

(Voe Board4, Half Barrela) [10 Fest (a m} from FATO Fdge)

Figure 2-6. In-ground and raised muarkers

FATO WITHOUT A TLOF

IN-GROUND MARKERS (Concrete, Stone, 'ISmbera) [On FATO Elge]

NATURAL ADOVE GROUND MARKERS (Low Hedge, Flower Bed) (10 Foct (3 ri) from FATO Edgel

FATO WITHOUT A TLOF

AC 150/5390-2A

BUT NOT LESS TIAN 1O FEET (S IL) LO ROTOR DIAMETER SAFCTY AREA AC 150/5390-2A

A 12 1NOH (00 em LASIIED LINE DEFINES FATO EDGE (i e. 1 5 OVERALL LENGTH)

FATO

APPROACH/TAKEOFF SURFACE

Figure 2-7. Marking paved beliports A 18 INGH {O cm) SOLID LINE DEFINFS TLOF EDGE (i.P, 1.0 SIID LENGTED) TLOF

APPROACH/TAKEOFF SURFACE

NOTE: THE PATO, TLOF, AND SAFETY AREA ARE SCALED TO THE ILLUISTRATED UELICOPTER

1/20/94

YEL X. ES IDEN INCG

Figure 2-8. A closed heliport

AC 150/5390-2A 1/20/94

Figure: 2-9. Lighting a privae use heliport

ALTERNATE OMNIDIRBOTIONAL OMNIDIRFCTIONAL LIGIT LUICATICIN LICHT LOCATION 5' (1.5 m) - B" (A em)

TLOF SURFACE

TLOF SURFACE

SAFETY NEIVSHELI

1/20/94

FATO LIMITS

FLUSH LIOHTS

RAISED TLOF

REQUIRED WHEN TLOF SURFACE RAISED MORE THAN 30" (75 em)

LIX3

5 FOOT

ROOF SIRPACE Figure 2-10. Lighting an elevated private use hellipont AND EDGE LIGHT PLACEMENT INSET OF SAFETY NETSIEL,P

SAFET

WIND BOCK

1/8 ROTOR/10 FOOT (3 m) MIN.

WIND BOCK

AC 150/5390-2A

CHAPTER 3. PUBLIC USE GENERAL AVIATION HELIPORTS

23. GENERAL. A public use heliport is a heliport available for use by the general public without a requirement for prior approval of the owner or operator. A public use general aviation heliport accommodates helicopters used by individuals, corporations, and helicopter air taxi services. Scheduled passenger services may be available if sufficient demand exists. The property needed for a public use general aviation heliport depends upon the volume and type of users and the scope of amenities, including automobile parking, provided. Property requirements for helicopter operators and for passenger amenities frequently exceeds that required for "air side" purposes. While the typical public use general aviation heliport is also publicly owned, public ownership is not a requirement for the public use designation. Public agencies and persons proposing to develop a general aviation heliport are encouraged to select a heliport site that has the potential for future expansion. This chapter contains standards and recommendations for designing a public use general aviation heliport. Figure 3-1 illustrates the essential features of a public use general aviation heliport.

CHAPTER 3. PUBLIC USE GENERAL AVIATION HELIPORTS

NOTE: To the extent that it is feasible to do so, existing public use heliports should be brought into conformity with the standards and recommendations in this AC at such time as major expansion or reconstruction is undertaken.

24. FINAL APPROACH AND TAKEOFF AREA (FATO). A public use general aviation heliport must have at least one FATO. The FATO may contain one or more touchdown lift-off areas--locations within its borders at which arriving helicopters terminate their approach in a hover or a landing, and from which departing helicopters takeoff.

a. Location. The FATO of a general aviation heliport may be at ground or water level, or at rooftop level.

b. Size. The least dimension (length, width, or diameter) of the FATO shall not be less than 1.5 times the overall length of the design helicopter. For heliports at elevations of 1,000 feet (300 m) or more above mean sea level, elongation by the amount determined from figure 3-2 is recommended. The elongation should be in the direction of takeoff.

c. Gradients. The FATO should be graded to remove surface irregularities and assure drainage. The recommended gradients for the FATO range from a minimum of 0.5 percent to a maximum of 5.0 percent. FATO grades should not exceed 2 percent in any area where a helicopter is expected to land.

25. SAFETY AREA. A safety area equal to 1/3 the rotor diameter of the design helicopter, but not less than 20 feet (6 m) in width, surrounds the FATO. The FATO and the safety area must be free and clear of objects such as parked helicopters, buildings, fences, or objects which could be struck by the main or tail rotor, or catch the skids, of an arriving or departing helicopter.

26. TOUCHDOWN AND LIFT-OFF AREA (TLOF). When the entire FATO is load bearing, an identifiable TLOF may not be required. A TLOF may have any shape. TLOFs are paved or other hard surfaces normally centered in the FATO. For irregularly shaped or oversized FATOs, the center of a TLOF is located at least 3/4 of the design helicopter's overall length in from the FATO boundaries. An elongated FATO may have an elongated TLOF or contain more than one TLOF as illustrated in figure 3-3.

a. Size. The recommended minimum dimension of the TLOF should not be less than the rotor diameter of the design helicopter.

b. Surface Characteristics. A Portland Cement Concrete (PCC) surface is recommended for ground level heliports. An asphaltic surface is "less desirable" for heliports as it may rut under the wheels or skids of a parked helicopter, a possible factor in some roll-over incidents. Pavements should have a broomed or other roughened finish that provides a skid resistant surface for helicopters and non-slippery footing for persons. Pavements should be designed to support 1.5 times the maximum takeoff weight of the design helicopter.

c. Elevated TLOFs. Elevated heliport TLOFs may be constructed of wood, metal, or concrete. The TLOF should be designed to support 1.5 times the maximum takeoff weight of the design helicopter. When the TLOF is on a platform elevated more than 30 inches (75 cm) above its surroundings, a 5 foot (1.5 m) wide safety net or shelf should be provided in lieu of a railing. The safety net or shelf should have a load carrying capability of at least 25 pounds per square foot (122 Kg per sq. m). The net or shelf, as illustrated in figure 3-4, should not project more than 2 inches (5 cm) above the level of the TLOF.

AC 150/5390-2A 1/20/94

d. Gradients. To assure drainage, the TLOF should have a minimum gradient of 0.5 percent and a maximum gradient of 2.0 percent. To insure TLOF drainage, gradients of rapid runoff shoulders should range between 2.0 and 5.0 percent.

27. APPROACH/TAKEOFF SURFACE.

a. Approach/Takeoff Path. A public use general aviation heliport should have more than one approach/takeoff path. One of these paths should be oriented to align with the direction of the predominant wind. Approach/takeoff paths may curve to avoid objects and/or noise sensitive areas and utilize the airspace above public lands e.g. freeways, rivers, etc.

b. Approach/Takeoff Surface. An approach/takeoff surface is centered on each approach/takeoff path and conforms to the dimensions of the FAR Part 77 heliport approach surface. Figure 1­ 6 illustrates the FAR Part 77 heliport approach and transitional surfaces which must be free of hazards to air navigation. Paragraph 8 provides guidance on how to identify and mitigate hazards to air navigation.

28. PROTECTION ZONE. The protection zone is the property under lying the approach/takeoff surface out to where the surface is 35 feet (10.5 m) above the heliport elevation as illustrated in figure 3-5. The heliport proponent should own or control this property. The control should include the ability to clear incompatible objects and to preclude activities that contribute to the congregation of people.

29. TAXI ROUTES AND TAXIWAYS. A taxi route is both an object free right-of-way connecting the FATO to a parking area/apron, and a maneuvering aisle on the parking area/apron. Taxiways are paved surfaces, normally centered in a taxi route, used by wheel equipped helicopters in ground maneuvering. The relationship between taxi routes and paved taxiways is illustrated in figures 3-6 and 3-7.

a. Widths.

(1) Taxi Routes. The width of a taxi route is determined by adding the clearance specified in "b" below to the maximum rotor diameter of the helicopter that will hover or ground taxi.

(2) Taxiways. The width of a paved taxiway should be designed to provide at least twice the undercarriage width of the design helicopter.

b. Clearances. Taxi routes and taxiways should be designed to provide 20 feet (6 m) of rotor tip clearance to objects and parked helicopters for hover taxiing, and 10 feet (3 m) of clearance for ground taxiing.

c. Surfaces. Unpaved portions of taxi routes should have a turf cover, or be treated in some manner, to prevent dirt and debris from being raised by a taxiing helicopter's rotor wash. Taxiways may have an asphaltic, portland cement, or other stabilized surface. Taxiway pavements should be capable of sustaining the maximum gross weight of the design helicopter under all weather conditions.

d. Gradients. Taxiway longitudinal gradients should not exceed 2.0 percent. Transverse gradients should not be less than 0.5 percent nor greater than 2.0 percent.

30. HELICOPTER PARKING. A public use general aviation heliport, unless designed as a helistop, should have an area designated for parking helicopters. The size of the area or apron depends upon the number of helicopters to be accommodated. Parking positions should be designed to accommodate the range of helicopter sizes expected at the facility. Individual parking pads may be used in lieu of an apron.

a. Size. Parking position size is dependent upon the helicopter size and the intended paths in maneuvering in and out of the parking position. There should be at least 1/3 rotor, but not less than 10 feet (3 m), of clearance between skid equipped helicopters and at least 10 feet (3 m) for wheel equipped helicopters to another helicopter or object. Clearances are measured from any part of a helicopter with the helicopter on the intended path. Tail rotor clearance may become the critical clearance when the helicopter turns 30 degree or more within a parking position. Figure 3-7 illustrates apron design concepts and figure 3-15 illustrates parking position clearances.

b. Parking Pads. The least dimension of a parking pad should be a minimum of 1.5 times the undercarriage length or width of the design helicopter.

c. Fueling. AC 150/5230-4, Aircraft Fuel Storage, Handling, and Dispensing on Airports, contains guidance on fueling services. Systems for storing and dispensing fuel must conform to federal, state, and local requirements for petroleum handling facilities. Guidance is found in AC 150/5230-4, Aircraft Fuel

Storage, Handling, and Dispensing on Airports, and appropriate National Fire Protection Association (NFPA) publications. Fueling locations should be designed and marked to minimize the potential for helicopters to collide with the dispensing equipment. The area should be lighted if night fueling operations are contemplated.

d. Additional Apron. Additional area may be required adjacent to hangars used by private helicopter owners and for hangars and other structures used by fixed base operators.

e. Tie Downs. Recessed tie downs may be installed to accommodate extended or overnight parking of based or transient helicopters. Guidance on recessed tie downs recommended for extended or overnight parking is found in AC 20-35, Tiedown Sense.

31. HELIPORT MARKERS AND MARKINGS. Markers and/or surface markings identify the facility as a heliport, the perimeter of the FATO and TLOF, any taxi route, taxiway, and/or parking positions. Surface markings may be paint or preformed material. Heliport FATOs and TLOFs are defined with in-ground markers and/or surface white lines. Taxi routes are defined with raised edge markers. Taxiways and aprons are defined with yellow lines/markings. Lines/markings may be outlined with a 6 inch (15 cm) wide stripe of a contrasting color to enhance conspicuity.

a. Perimeter Markings. The perimeter of the FATO and/or TLOF should be defined with markers and/or lines. Figure 3-8 illustrates a heliport with inground markers and surface markings while figure 3-9 illustrates a heliport with surface markings.

(1) Unpaved FATOs. The perimeter of an unpaved FATO is defined with in-ground markers, approximately 1 foot by 5 foot (30 cm by 1.5 m), located at the corners and along the FATO edges.

(2) Paved FATOs. A 1 foot (30 cm) wide dashed white line defines the FATO perimeter. The segments and separation between segments should be even. The corners must be defined and the edge segments should be approximately 5 feet (1.5 m) in length.

(3) TLOFs. A continuous 12 inch (30 cm) wide solid white line defines the perimeter of a paved or hard surfaced TLOF. A continuous 12 inch (30 cm) inground marking defines the perimeter of a load-bearing aggregate-turf TLOF.

b. Identification Marking. An in-ground H marking will identify the heliport as a public use facility as well as mark the intended landing position within the FATO. The letter H is illustrated in figures 3-7 and 3-8. The H is oriented on the axis of the dominate approach/takeoff path. A bar may be placed under the H when it is necessary to distinguish the preferred approach direction. Appendix 2 contains dimension recommendations.

c. Taxi Route and Taxiway Markings. Taxi route edges are defined with yellow-blue-yellow raised markers that are not more than 8 inches (20 cm) in height nor less than 4 inches (10 cm) in diameter. Taxiway centerline and edges are marked with yellow lines. The centerline is a continuous 6 inch (15 cm) wide yellow line. The edges are defined with two continuous 6 inch (15 cm) wide yellow lines spaced 6 inches (15 cm) apart. Figure 3-6 illustrates taxiway centerline and edge markings.

d. Apron Markings. In addition to the taxiway and parking position markings, the yellow (double) taxiway edge lines continue around the apron to define the apron edge. Figures 3-7 and 3-15 illustrate apron markings.

e. Parking Position Markings. The yellow taxiway centerline continues into the individual parking positions to define the centerline of the parking positions. A parking position is further identified by a 12 inch (30 cm) wide yellow line defining a circle. The diameter of the circle is equal to the rotor diameter of the largest helicopter the position is designed to accommodate.

f. Closed Heliport. All markings of a permanently closed heliport, FATO, or TLOF should be obliterated. If it is impractical to obliterate markings, a yellow X, as illustrated in figure 3-10, should be placed over the H. The yellow X must be large enough to ensure early pilot recognition that the heliport is closed.

32. HELIPORT LIGHTING. For night operations, the FATO or TLOF, but not both, and taxiways (or taxi routes) need to be lighted. Yellow lights define the limits of the FATO or TLOF. Flush green lights define taxiway centerlines. Blue omni-directional lights or reflectors define taxi route edges. Figure 3-11 illustrates these lighting systems. AC 150/5340-19, Taxiway Centerline Lighting System, AC 150/5340-24, Runway and Taxiway Edge Lighting System, and AC 150/5345­ 46, Specification for Runway and Taxiway Light Fixtures, contain technical guidance on lighting equipment and installation details.

AC 150/5390-2A 1/20/94

a. Perimeter Lights. A minimum of 4 flush or raised light fixtures is recommended per side of a square or rectangular FATO or TLOF. A light is located at each corner with additional lights uniformly spaced between the corner lights with a maximum interval of 25 feet (7.5 m) between lights. An even number of lights, at least eight, uniformly spaced with a maximum interval of 25 feet (7.5 m) between lights is required to define a circular FATO or TLOF. Flush lights may be located on the TLOF edge or within 1 foot (30 cm) of the TLOF edge. Raised light fixtures, modified to be no more than 8 inches (20 cm) in height, should be located 10 feet (3 m) out from the TLOF edge and should not penetrate a horizontal plane at the TLOF's elevation by more than 2 inches (5 cm). When non-flush lights are used on a raised TLOF, they should be positioned as illustrated in figure 3-11. In snow areas, it is recommended that these lights be placed along the outer edge of the safety net/shelf to minimize the chances of being damaged by snow removal operations.

b. Landing Direction Lights. Landing direction lights are a configuration of five L-861 lights with omni- directional yellow lenses. The lights are spaced at 15 foot (4.5 m) intervals beginning at the line of perimeter lights and extend outward in the direction of the preferred approach/takeoff path as illustrated in figure 3-11. Landing direction lights are an optional feature to be installed when it is necessary to provide directional guidance.

c. Taxi Route and Taxiway Lighting.

(1) Taxi Routes. The edges of a taxi route, that does not contain a paved taxiway, are defined with blue lenses on raised lighting fixtures or reflectors modified to be no more than 8 inches (20 cm) tall. Taxi route lights or reflectors are placed at intervals of 50 feet (15 m) on straight sections and 25 feet (7.5 m) on curved sections. A minimum of four lights are needed to define a curve. Blue retro-reflector Type II markers spaced at 50 foot (15 m) intervals may be used to identify the edges of a taxi route.

(2) Taxiways. Taxiway centerlines are defined with flush L-852A bi-directional or L-852B unidirectional green lights. The lights are spaced at 50 feet (15 m) intervals on straight sections and at 25 feet (7.5 m) intervals on curved sections with a minimum of four lights needed to define the curve. Green retro- reflective markers meeting requirements for Type II markers in AC 150/5345-39, FAA Specification L-853, Runway and Taxiway Centerline Retro-reflective

Markers, may be used in lieu of the L-852A or L-852B lighting fixtures.

b. Heliport Identification Beacon. A heliport identification beacon is recommended to aid pilots in locating the heliport when its location cannot be readily identified by a prominent lighted landmark. The beacon, flashing white/green/yellow at the rate of 30 to 45 flashes per minute, should be located on or close to the heliport. Guidance on heliport beacons is found in AC 150/5345-12, Specification for Airport and Heliport Beacon.

e. Floodlights. Floodlights may be used to illuminate the apron. To eliminate the need for tall poles, these floodlights may be mounted on adjacent buildings. Care should be taken, however, to place floodlights clear of the safety area, the approach/takeoff surface(s), and the heliport transitional surfaces. Floodlights should be aimed down and provide a minimum of 3 foot candles (32 lux) of illumination on the apron surface. Floodlights which might interfere with pilot vision during takeoff and landings must be capable of being turned off during landings and takeoffs.

33. WIND DIRECTION INDICATOR. A wind sock conforming to AC 150/5345-27, Specification for Wind Cone Assemblies, is recommended to show the direction and magnitude of the wind. Wind socks must be lighted for night operations. The wind sock should be placed where it provides a true indication of surface wind and is clear of the safety area, the approach/takeoff surface(s), and the heliport transitional surfaces. The wind sock should provide the best possible color contrast to its background. When the heliport is large or located among buildings, wind direction and speed may differ significantly from one part of the heliport to another and multiple wind socks may be necessary.

34. VISUAL GLIDE PATH INDICATORS. A visual glide path indicator, such as Heliport Approach Path Indicator (HAPI), Visual Approach Slope Indicator (VASI), or Precision Approach Path Indicator (PAPI), provides pilots with visual course and descent cues. The lowest on course visual signal must provide a minimum of 1 degree of clearance over any object in the approach path that lies within 10 degrees of the approach course centerline. The optimum location of a visual glide path indicator is on the extended centerline of the approach path at a distance that brings the helicopter to a hover 3 to 8 feet (0.9 to 2.5 m) above the TLOF center. Figure 3-12 illustrates visual glide path indicator clearance criteria. AC 150/5345-28, Precision Approach Path Indicator (PAPI) Systems, and AC 150/5345-52, Generic

Visual Glideslope Indicators (GVGI), provide additional information.

35. TERMINAL FACILITIES. The heliport terminal requires curb side access for passengers using private autos, taxicabs, and public transit vehicles. Public waiting areas need the usual amenities and a counter for rental car services may be desirable. Passenger auto parking areas should accommodate current requirements and have the capability of being expanded to meet future requirements. Readily available public transportation may reduce the requirement for employees and service personnel auto parking spaces. The heliport terminal building or sheltered waiting area should be attractive and functional. AC 150/5360-9, Planning and Design of Airport Terminal Facilities at Non-Hub Locations, contains guidance on designing terminal facilities.

36. SAFETY CONSIDERATIONS. The following safety related features should be provided on an as needed basis.

a. Wire Marking And Lighting. Unmarked electric and telephone wires in the heliports immediate area may be difficult to see. It is recommended that, where practical, wires located within 500 feet (150 m) of the FATO, as well as those within 1/2 mile (1 km) that are beneath and up to 100 feet (30 m) to the side of an approach/takeoff path be marked to make them more conspicuous. Figure 3-13, illustrates the area of concern. Guidance on marking and lighting objects is contained in AC 70/7460-1, Obstruction Marking and Lighting.

b. Security. Ground level general aviation heliports may require their operational areas to be fenced to prevent the inadvertent or unauthorized entry of persons or vehicles. Fences should be as low as possible and located as far as possible from the FATO. Fences should not penetrate any approach/ takeoff or transitional surface. Access to airside areas should be through controlled and locked gates or doors displaying a cautionary sign similar to that illustrated in figure 3-14.

c. Rescue and Fire Fighting Services. Rescue and fire fighting service requirements vary. Public use utility heliports should meet (NFPA) Pamphlet 418, Standards for Heliports, and (NFPA) Pamphlet 403, Aircraft Rescue Services, criteria. A fire hose cabinet or extinguisher should be provided at each access gate and each fueling location. Fire hose cabinets, fire extinguishers, and other fire fighting equipment at elevated TLOFs should be located adjacent to, but below the level of the TLOF.

d. Equipment/Object Marking. Heliport maintenance and servicing equipment, as well as other objects used in the air side operational areas, should be made conspicuous with reflective tape, paint, or other markings. Particular attention should be given to marking objects that are hard to see in marginal visibility such as at night, in mist, or in fog.

e. Passenger Walkways. Passenger movement in operational areas should be restricted to marked walkways. Figure 3-15 illustrates one marking scheme. Apron pavements should be designed so that spilled fuel does not drain onto passenger walkways or toward parked helicopters. Two separated access points are required for elevated TLOFs.

f. Communications and Weather. A UNICOM radio may be used to provide arriving helicopters with heliport and traffic advisory information but may not be used to control air traffic. The Federal Communications Commission (FCC) should be contacted for information on UNICOM licensing. An AWOS measures and automatically broadcasts current weather conditions at the heliport site. When an AWOS is installed, it should be located at least 100 feet (30 m) and not more than 700 feet (215 m) from the edge of the TLOF. Guidance on AWOS systems is found in AC 150/5220-16, Automated Weather Observing Systems (AWOS) for Non- Federal Applications.

g. Winter Operations. Swirling snow raised by a landing helicopter's rotor wash can cause the pilot to lose sight of the intended landing point. Swirling snow on takeoff can hide objects which need to be avoided. At least the TLOF, and as much of the FATO and the safety area as practical, should be kept free of snow. Guidance on winter operations is found in AC 150/5200-30, Airport Winter Safety and Operations.

37. ZONING AND COMPATIBLE LAND USE. Where state statutes permit, the sponsor of a public use general aviation heliport is encouraged to promote the adoption of zoning measures to ensure that the heliport will continue to be available for public use as well as to protect the community's investment in the facility.

a. Zoning to Limit Building/Object Heights. General guidance on drafting an ordinance which would limit building and object heights is contained in AC 150/5190-4, A Model Zoning Ordinance to Limit Height of Objects Around Airports. The ordinance should substitute the heliport surfaces for the airport surfaces in the model ordinance.

AC 150/5390-2A 1/20/94

b. Zoning for Compatible Land Use. A zoning ordinance may be enacted, or an existing ordinance modified, to control the use of property within the heliports approach/takeoff path environment. The ordinance should restrict activities to those which are compatible with helicopter operations.

1/20/94 AC 150/5390-2A APESCE SAY AA

1/20/94 AC 150/5390-2A APESCE SAY AA

ATO INRRS

Pigure 3-1. Essential features of » general aviation heliport

AC 150/5390-2A

1/20/94

ADN D O RS)

E TTE O E OT

006

000

100

5

44 SIO O T)

Figure 3-2. FATO length increase for elevation

1/20/94

F

TOF FOR TAKEOFF IN -TLOF OPPOSITE DIREÇTION TAKE-OFF DIRECTION

TOF FOR TAKEOFF IN -TLOF OPPOSITE DIREÇTION TAKE-OFF DIRECTION

FATO

RECOMMENDED FATO/TLOF RELATIONSHIPS Figure 3-3. A leagthened FATO with two TLOFt FOR A GENERAL AVIATION HELIPORT A-FATO WIDTH B-FATO LENGTH C.TLOF LENGTH AND/OR WIDTH ADDITION FROM FIGURE 3-2 1.6 x OVERALL LENGTH 1.5 x OVERALL LENGTH PLUS

1.0 x ROTOR DIAMETER D-DISTANOE FROM FATO EDGE TO CENTER OF TLOF 0.75 x OVERALL. LENGTH E--SAFETY AREA 0.33 ROTOR DIAMETER MINIMUM OF 20 FEET (6 m) F-RECOMMENDED MINIMUM DISTANCE BETWEEN TLOF EDGES DEVELOPED FOR 3 OPPOSITE DIRECTION OPERATIONS 1.0 : ROTOR DIAMETER AC 150/5390-2A

AC 150/5390-2A 1/20/94

FATO LIMITS

FATO LIMITS

FLUSH LIGHTS

FATO

RAISED TLOF

5 FOOT (1.5m) SAFETY NETISHELF

AUTRORIZEUPERRONMELONLY CALTTON KELEOPTER LANDNGANEA AUTRORREDPERSONMELONAY WIND SOCK

Figure 3-4. Raised TLOF with a safety net

2:1 TRANSITIONAL SURFACE

SAFETY AREA

FATO PROTECTION ZONE

2:1 TRANSITIONÁL SURFACE Figure 3-5. Protection zone 280 FEET (85.3m) ON LEVEL (ROIJNO

2:1 TRANSITIONAL. SURFACE

2:1 TRANSITIONAL. SURFACE

FATO PROTECTTON ZONE

1/20/94

APPROACH/TAKEOFF SURFACE

FLIGHT TRACK OF HELICOFTER APPROACH/TAKEOFF SURFACE 8:1 SLOPE 35 FEFT (10.6 m)

AC 150/5390-2A

AC 150/5390-2A 1/20/94

20 FEET (6 m)

ROTOR DAMETER

20 FEET (θ m) TAXI ROUTE WIDTH = ROTOR DLAMETER + 2 × REQ'D CLEARANCE

20 FEET (θ m) TAXI ROUTE WIDTH = ROTOR DLAMETER + 2 × REQ'D CLEARANCE

8INCI(20 cm)HIGH TAXI ROUTE EDGE MARKERS 2 INCH (5 cm: WIDE DANDS YELLOW-BLUE-YELLOW

TAXI ROUTE WITIIOUT A PAVED TAXIWAY

10 FEET YELLOW CENTEHLINE STRITE

ROTOR DAMETER

GREEN TAXIWAY TAKTWAY WITH EQUAL TO 11 UNDERCARRIAGE WIDTH YELLOW DOLBLF. LINE EOGE STUIPES

CENTERLINE LIÇHTS 10 FEET (3 )

TAXI ROUTE WTDTH ■ ROTOR DUMETER – 1 ± REQD CLEARANCE

TAXI ROUTE WTDTH ■ ROTOR DUMETER – 1 ± REQD CLEARANCE

TAXI ROUTE WITH PAVED TAXIWAY

Figure 3-6. Taxi route and taxiway markings

ROUTE TAU ROUTE

POSITIONS ÁRE RPOTANGLES EQUAT. TO HtiCOPtER 1ENOTH AND WIDTH

13 ROTORIO MJN, CLEÁRANCÉ

Figure 3-7. Parking aproa design PARKING bFSIÓNED SO THAT 10 ROTORIGI3 m) MIN, CLEARANCE

HELHOOPTFR EXIS OY TALXING FORWARD

HELHOOPTFR EXIS OY TALXING FORWARD

1/20/94

TAXI NOUTE

POG|TIONS ARE QIRCLES TAT ASSIRE TAIL ROTOR CLEARANCE

- 1/1 ROTON L0 FEET (O > CLEAMANCE

13 ROTR 10 FEET (0 ml

7

PARKING DESIONED SO THAT 1IELICOPTER MUST PRVOT AAÓTT HUTUE MAST OR WIEEL TO EXIT H

AC 150/5390-2A

AC 150/5390-2A

'IN.GROUND MAEKER

'IN.GROUND MAEKER

WIND SOCK

1/20/94

APPROACH/TAKEOFF SURFACE

IN-GROUND FATO CORNEREDGE MARKERS

PAINTED TLOP EDGEMARKING TAX ROUTE MARKER

1 1

HELIPORT-H MARKING TO PARKING AREA

1

SAFETY AREA

APPROACH/TAKEOFF SURFACE

Figure 3-8. Heliport with markers and markiogs

APPROACH/TAKEOFF SURFACE

DASHED FATO EDOE MARHING

DASHED FATO EDOE MARHING

SOLID TLOF EDGE MARKING TAXI ROUTEMARKER

7 HELIPORT *H" MAEKING TAXIWAY CENTERLINE

WIND SOCK TAXIWAY EDGE MARKINC

SAFETY AREA

APPROACH/TAKEOFF SURFACE

Figue 3-9. Helipon wità surfaxe markiogsi

AC 150/5390-2A 1/20/94

Figure 3-10. Marking a dlosed belipon

LIOHTED WIND SOCK

LIOHTED WIND SOCK

Figure 3-1 l. Lighting system for night operations 1 FOOT (30 em) IN-PAVEMENT FLUSII YELLOW LIGHTS

1/20/94

BLANDING DIRECTION LIGHTS (OPTIONAL FEATURE)

RAISED YELLOW OMNI-DIRECTIONAL LIFGIITS

2 INOIPS (5 em) MAXIMUM PENETRATION

IN-OROUND FATO CORNERFDGE MARKERS

FLUSH IN-PAVEMENT LIGIIT DETAIL (Seo Figure θ-1 for shoulder details)

IN-OROUND FATO CORNERFDGE MARKERS

s INCH (20 eua)

10 PEET (9 mH

OMNI-DIRECTIONAL LIGIT DETAIL (See Figure 9-1 for shoulder detaits)

AC 150/5390-2A

AC 150/5390-2A

WIND SOCK

CLME PATH INDICATOR (GPI)

10°

COURSE CENTERLINE

CRITICAL. OBJECT

LOWER LIMIT OF ON COUREE SIGNAL

1/20/94

OBSTACLE CLEARANCE PLANE

1°MINIMUM CLEARANCE

OFSTACLE CLEARANCE REFERENCE LINE

OFSTACLE CLEARANCE REFERENCE LINE

GPI

VARLABI.E→

CRITICAL QRJECT

Figure 3-12. Visual gfide path indicator sitiog and clearanke criteria

WIND SOCK 500 FEET (150 m) 100 FEET (30 m)

APPROACH/TAKEOFFSURFACE

100 FEET (30 m) POLE LINE SHOULD BE MARKED/LIGHTED

OBSTRUOTION 090) LIGHTS ON AUILDINO

PLAN VIEW

PLAN VIEW

APPROACH/TAKEOFF SURFACE

SEE INSET RECOMMEND THAT WIRES & OBJECTS PROFILE VIEW THIS AREA ALSO BE

81 APPROACH/TAKEOFF SURFACE 25:1 20 FEET (6 m) 9.21:2 MARKED/LIGHTED

316 FEET (92 ) -500 FEET (150 m)-

INSET NOT TO SCALE

Figure 3-13. Recommended area for wire marking and’or lighting

INSET NOT TO SCALE

AC 150/5390-2A 1/20/94

BE ALERT

AROUND THE HELICOPTER

0

APPROACH AND LEAVE THE HELICOPTER IN A CROUCHED MANNER WHEN ROTORS ARE TURNING

ALWAYS AVOID THIS BLIND AREA AS THE HELICOPTER PILOT CANT SEE YOU

THE PILOT CAN'T SEE YOU HERE EITHER DON'T EVEN GET CLOSE TO THE TAIL ROTOR

Figure 3-14. Caution sign

ALWAYS AVOID THIS BLIND AREA AS THE HELICOPTER PILOT CANT SEE YOU

1/20/94

ILLUSTRATION PRESUMES THE

HELIÇOPTER ROTATES ABOUT PAINE THE MAST IN ORDER TO EXIT THE PARKING POSITION

CLEARANCE LINE BASED ON ARG OF TAIL ROTOR

CLEARANCE ARCS OF CLEARANCE ARCS OF ADAGENT POSITIONS ARC GENERATED BY TAIL ROTOR ADJACENT POSITONS MAY QYERLAP MAY OVERLAP

RADIUS – OVERAIL, IFNGTH -TN ROTOR DLAMETER

RADIUS – OVERAIL, IFNGTH -TN ROTOR DLAMETER

Figure 3-15. Apron parking position clearances PARKING CIRCLE (1 × ROTOR DTAMETEH) REOOMMENDED CLEARANCES: SKID FQUIPPBD HELICOPTERS PARKING CIRCLE (1 × ROTOR DIAMETER) EA

1/3 AOTOR DUT NOT LESS TILAN LD FEET (3 m) WHEEL EQUIPPED HELICOPTERS NOT LESS THAN 1O FEET (3 m)

FIRE FXTINÓCISHER -FIRR PXTMNGUISHER FENCE GATEWARNING SIGN GATE WARNINGSIGN YENCE

4 AC 150/5390-2A

4 AC 150/5390-2A

CHAPTER 4. TRANSPORT HELIPORTS

38. GENERAL. A transport heliport is available for use by the general public without a requirement for prior approval of the owner or operator and is intended to accommodate air carrier operators providing scheduled service with large helicopters. When the heliport is served by helicopters carrying more than 30 passengers, the heliport operator is required to have an FAA certificate issued under FAR Part 139, Certification and Operations: Land Airports Serving Certain Air Carriers. Because of the need for allweather operating capability, public agencies planning a transport heliport are encouraged to select a site capable of accommodating precision instrument operations. This chapter contains standards and recommendations for designing a transport heliport. Figure 4-1 illustrates the essential features of a transport heliport.

CHAPTER 4. TRANSPORT HELIPORTS

NOTE: If operations by tilt rotor aircraft are contemplated, criteria in AC 150/5390-3, Vertiport Design is applicable.

39. FINAL APPROACH AND TAKEOFF AREA (FATO). A transport heliport must have a FATO which may contain one or more touchdown liftoff areas­ - locations within the FATO at which arriving helicopters terminate the approach and from which departing helicopters takeoff.

a. Location. The FATO of a transport heliport is normally at ground level but may be developed with the TLOF located on a pier, or when carefully planned, on the roof of a building. Figure 4-2 depicts a FATO extending over water.

b. Size. FATOs are normally rectangles with the long axis aligned with the prevailing wind. FATO width is based on the rotor diameter of the design helicopter. FATO length is based on the elevation of the heliport site above mean sea level.

(1) FATO Width. The minimum width of a FATO should be at least 2 rotor diameters of the design helicopter. A recommended FATO width of 100 feet (30 m) will accommodate the majority of large helicopters in the current fleet.

(2) FATO Length. The minimum recommended FATO length is 200 feet (60 m). For heliports at elevations of 1,000 feet (300 m) or more above mean sea level, an elongated FATO as determined from figure 4-3 is recommended. The elongation should

be in the direction of takeoff. Figure 4-3 depicts recommended FATO lengths.

c. Gradients. The turf portions of a FATO should be graded to remove surface irregularities and assure drainage. Longitudinal gradients should match those of the paved touchdown and liftoff surface (TLOF). To insure drainage, a shoulder with gradients ranging between 2 and 5 percent should exist along the TLOF edge.

40. SAFETY AREA. A safety area not less than 30 foot (9 m) in width surrounds the FATO. The FATO and the safety area must be free and clear of objects such as parked helicopters, buildings, fences, etc. which could be struck by the main or tail rotor, or catch the skids, of an arriving or departing helicopter.

41. TOUCHDOWN AND LIFT-OFF AREA (TLOF). TLOFs are rectangular paved surfaces centered on the major axis of the FATO. For irregularly shaped or oversized FATOs, the center of the TLOF is located at least the rotor diameter of the design helicopter in from the FATO boundaries. Figure 4-4 illustrates this FATO/TLOF relationship.

a. Size. The minimum dimension of a the TLOF shall not be less than the rotor diameter of the design helicopter or 50 feet (15 m).

b. Surface Characteristics. A Portland Cement Concrete (PCC) surface is recommended for ground level heliports. An asphaltic surface is "less desirable" for heliports as it may rut under the wheels or skids of a parked helicopter, a possible factor in some roll-over incidents. Pavements should have a broomed or other roughened finish that provides a skid resistant surface for helicopters and non-slippery footing for persons. Pavements should be designed to support 1.5 times the maximum takeoff weight of the design helicopter.

c. Gradients. To assure drainage, the TLOF should have a maximum longitudinal gradient of 0.5 percent and a transverse gradient between 0.5 and 2.0 percent. 42. APPROACH/TAKEOFF SURFACE.

a. Approach/Takeoff Path. A transport heliport should have more than one approach/takeoff path. A path should be oriented to align with the direction of the

AC 150/5390-2A 1/20/94

predominant wind during visual conditions and, to the extent practicable, an other with the prevailing winds during instrument conditions. Visual approach/takeoff paths may curve to avoid objects, noise sensitive areas, and/or utilize the airspace above public lands e.g. freeways, rivers, etc.

b. Approach/Takeoff Surface. An approach/ takeoff surface is centered on each approach/takeoff path. The visual approach/takeoff surface conforms to the dimensions of the FAR Part 77 heliport approach surface. Figure 1-6 illustrates the heliport approach and transitional surfaces which must be free of hazards to air navigation. Paragraph 8 provides guidance on how to identify and mitigate hazards to air navigation. The approach/takeoff surface centered on the path aligned with the prevailing winds during instrument conditions should comply with the obstacle evaluation surfaces criteria cited in chapters 7 and 8.

43. PROTECTION ZONE. The protection zone is the property under lying the approach/takeoff surface out to where the surface is 35 feet (10.5 m) above the heliport elevation as illustrated in figure 4-5. The heliport proponent should own or control this property. The control should include the ability to clear incompatible objects and to preclude activities that contribute to the congregation of people.

44. TAXI ROUTES AND TAXIWAYS. A taxi route is both an object free right-of-way connecting the FATO to a parking area/apron, and a maneuvering aisle on the parking area/apron. Taxiways are paved surfaces, normally centered in a taxi route, used by helicopters in ground maneuvering. The relationship between taxi routes and paved taxiways is illustrated in figure 4-6.

a. Widths.

(1) Taxi Routes. The width of a taxi route is determined by adding the clearance specified in "b" below to the maximum rotor diameter of the helicopter that will hover or ground taxi.

(2) Taxiways. The width of paved taxiway should be at least twice the undercarriage width of the design helicopter.

b. Clearances. Taxi routes and taxiways should provide the design helicopter with 20 feet (6 m) of rotor tip clearance for hover taxiing and 10 feet (3 m) clearance for ground taxiing.

c. Surfaces. Unpaved portions of taxi routes should have a turf cover, or be treated in some manner, to prevent dirt and debris from being raised by a taxiing helicopter's rotor wash. Taxiways may have an asphaltic, portland cement, or other stabilized surface. Taxiway pavements should be capable of sustaining the maximum gross weight of the design helicopter under all weather conditions.

d. Gradients. Taxiway longitudinal gradients should not exceed 2.0 percent. Transverse gradients should not be less than 0.5 percent nor greater than 2.0 percent.

45. HELICOPTER PARKING. A transport heliport should have a paved apron for parking helicopters. The size of the apron depends upon the number of helicopters to be accommodated. Separate aprons may be established for specific functions such as passenger boarding, maintenance, and parking of based and transient helicopters. Parking positions should be designed to accommodate the range of helicopter sizes expected at the facility.

a. Size. Parking position size is dependent upon the helicopter size and the intended paths in maneuvering in and out of the parking position. There should be at least 1/3 rotor, but not less than 10 feet (3 m), of clearance between skid equipped helicopters and at least 10 feet (3 m) for wheel equipped helicopters to another helicopter or object. Clearances are measured from any part of a helicopter with the helicopter on the intended path. Tail rotor clearance may become the critical clearance when the helicopter turns 30 degree or more within a parking position. Figure 4-7 illustrates this design principle.

b. Fueling. AC 150/5230-4, Aircraft Fuel Storage, Handling, and Dispensing on Airports, contains guidance on fueling services. Systems for storing and dispensing fuel must conform to federal, state, and local requirements for petroleum handling facilities. Guidance is found in AC 150/5230-4, Aircraft Fuel Storage, Handling, and Dispensing on Airports, and appropriate National Fire Protection Association (NFPA) publications. Fueling locations should be designed and marked to minimize the potential for helicopters to collide with the dispensing equipment. The area should be lighted if night fueling operations are contemplated.

c. Additional Apron. Additional area may be required adjacent to hangars used by private helicopter owners and for hangars and other structures used by fixed base operators.

d. Tie Downs. Recessed tie downs may be installed to accommodate extended or over night parking of based or transient helicopters. Guidance on recessed tie downs recommended for extended or overnight parking is found in AC 20-35, Tiedown Sense.

46. HELIPORT MARKERS AND MARKINGS. Markers and/or surface markings identify the facility as a heliport, the perimeter of the FATO and TLOF, any taxi route, taxiway, and/or parking positions. Surface markings/lines may be paint or preformed material. Heliport FATOs and TLOFs are defined with in-ground markers and/or white lines. Taxi routes are defined with raised edge markers. Taxiways and aprons are defined with yellow lines/markings. Lines/markings may be outlined with a 6 inch (15 cm) wide stripe of a contrasting color to enhance conspicuity.

a. Perimeter Markings. The perimeter of the FATO and/or TLOF should be defined with markers and/or lines. Figure 4-8 illustrates a heliport with inground markers and surface markings while figure 4-9 illustrates a heliport with surface markings.

(1) Unpaved FATOs. The perimeter of an unpaved FATO is defined with in-ground markers, approximately 1 foot by 5 foot (30 cm by 1.5 m) located at the corners and along the FATO edges.

(2) Paved FATOs. A 1 foot (30 cm) wide dashed white line defines the FATO perimeter. The segments and separation between segments should be even. The corners must be defined and the edge segments should be approximately 5 feet (1.5 m) in length.

(3) TLOFs. A continuous 12 inch (30 cm) wide solid white line defines the perimeter of a paved or a hard surfaced TLOF.

b. Identification Marking. Transport heliports are identified by the white capital letter H centered on the TLOF as illustrated in figures 4-8 and 4-9. The H is oriented on the axis of the dominate approach/takeoff path. Appendix 2 contains dimension recommendations.

c. Closed Heliport. All markings of a permanently closed heliport, FATO, or TLOF should be obliterated. If it is impracticable to obliterate markings, a yellow X, as illustrated in figure 4-10, should be placed over the H. The yellow X must be large enough to ensure early pilot recognition that the heliport is closed.

d. Taxi Routes and Taxiway Markings. Taxi route edges are defined with yellow-blue-yellow raised

markers that are not more than 8 inches (20 cm) in height nor less than 4 inches (10 cm) in diameter. Taxiway centerlines and edges are marked with lines. The centerline is a continuous 6 inch (15 cm) wide yellow line. The edges are defined with two continuous 6 inch (15 cm) wide yellow lines spaced 6 inches (15 cm) apart. Figure 4-6 illustrates taxi route and taxiway centerline and edge markings.

e. Apron Markings. In addition to the taxiway and parking position markings, the yellow (double) taxiway edge lines continue around the apron to define the apron edge. Figure 4-7 illustrates apron markings.

f. Parking Position Markings. The yellow taxiway centerline continues into the individual parking positions to define the centerline of the parking positions. A parking position is further identified by a 12 inch (30 cm) wide yellow line defining a circle. The diameter of the circle is equal to the rotor diameter of the largest helicopter the position is designed to accommodate. The spacing between circles, and a circle and an object depends upon how much the helicopter must turn to exit the position. Refer to paragraph 45.a.

47. HELIPORT LIGHTING. For night operations, the TLOF and taxiways (or taxi routes) need to be lighted. Yellow lights define the limits of the TLOF. Green lights define taxi route and taxiway centerlines. Alternatively, blue lights may be used to define taxiway and taxi route edges. Figure 4-11 illustrates these lighting systems. AC 150/5340-19, Taxiway Centerline Lighting System, AC 150/5340-24, Runway and Taxiway Edge Lighting System, and AC 150/5345-46, Specification for Runway and Taxiway Light Fixtures, contain technical guidance on lighting equipment and installation details.

a. Perimeter Lights. A minimum of 5 lights are recommended per side or end of the TLOF. A light is located at each corner with additional lights uniformly spaced between the corner lights with a maximum interval of 25 feet (7.5 m) between lights. Flush lights may be located on, or within 1 foot (3 cm) of, the TLOF edge. Raised light fixtures, modified to be no more than 8 inches (20 cm) in height, may be located 10 feet (3 m) out from the TLOF edge and should not penetrate a horizontal plane at the TLOF's elevation by more than 2 inches (5 cm).

b. Landing Direction Lights. An optional feature, landing direction lights, is a configuration of five L-861 lights fitted with omni-directional yellow lenses. The lights are spaced at 15 foot (4.5 m) intervals beginning at the line of perimeter lights and extending

AC 150/5390-2A 1/20/94

outward in the direction of the preferred approach/takeoff path as illustrated in figure 4-11.

c. Taxiways. Taxiway centerlines are defined with flush bi-directional or uni-directional green lights. Alternatively, taxiway edges may be marked with blue taxiway edge lights. Lights are spaced at 50 feet (15 m) intervals on straight sections and at 25 feet (7.5 m) intervals on curved sections with a minimum of four lights needed to define the curve. Green retro-reflective markers meeting requirements for Type II markers in AC 150/5345-39, FAA Specification L-853, Runway and Taxiway Centerline Retro-reflective Markers, may be used in lieu of the centerline lighting fixtures. Blue retro- reflective markers may be used in lieu of edge lights.

d. Heliport Identification Beacon. A heliport identification beacon is recommended to aid in locating the heliport. The beacon, flashing white/green/yellow at the rate of 30 to 45 flashes per minute, should be located on or close to the heliport. Guidance on heliport beacons is found in AC 150/5345-12, Specification for Airport and Heliport Beacon.

e. Floodlights. Floodlights may be used to illuminate the apron area. Care should be taken to place floodlights clear of the safety area, the approach/takeoff surface(s), and the heliport transitional surfaces and not interfere with pilot vision.

48. WIND DIRECTION INDICATOR. A wind sock conforming to AC 150/5345-27, Specification for Wind Cone Assemblies, is recommended to show the direction and magnitude of the wind. Wind socks must be lighted for night operations. The wind sock should be placed where it provides a true indication of surface wind and is clear of the safety area, the approach/takeoff surface(s), and the heliport transitional surfaces. The wind sock should provide the best possible color contrast to its background. When the heliport is large or located among buildings, wind direction and speed may differ significantly from one part of the heliport to another and multiple wind socks may be necessary.

49. VISUAL GLIDE PATH INDICATORS. A visual glide path indicator, such as Heliport Approach Path Indicator (HAPI), Visual Approach Slope Indicator (VASI), or Precision Approach Path Indicator (PAPI), provides pilots with visual course and descent cues. The lowest on course visual signal must provide a minimum of 1 degree of clearance over any object in the approach path that lies within 10 degrees of the approach course centerline. The optimum location of a visual glide path indicator is on the extended centerline of the approach

path at a distance that brings the helicopter to a hover 3 to 8 foot (0.9 to 2.5 m) above the TLOF. Figure 4-12 illustrates visual glide path indicator clearance criteria. AC 150/5345-28, Precision Approach Path Indicator (PAPI) Systems, and AC 150/5345-52, Generic Visual Glideslope Indicators (GVGI), provide additional information.

Continue reading ↓ 120 of 207 passages shown