Radar Vectors
Advisory Circular Cancelled Issued May 31, 1991 AAS-100 39 pages Copy saved Nov 18, 2026

AC 150/5390-3 Vertiport Design

Provides guidance to planners and communities interested in developing a civil vertiport or vertistop.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (2 of 39 pages). Check the original, as some words may be misread.

U.S. Deportment of lronsportotiorl Fe&ml Aviation Adminirtmtion

Advisory Circular

s”bjcct: VERTIPORT DESIGN

1. PURPOSE. This advisory circular (AC) provides guidance to planners and communities interested in developing a civil vertiport or vertistop.

2. APPLICATION. The standards and recommendations contained in this AC are recommended by the FAA for use in the design of civil vertiports and vertistops. For vertiport projects receiving Federal grant-in-aid assistance, the use of these standards is mandatory. At certificated vertiports, the standards may be used to satisfy specific requirements of Federal Aviation Regulations (FAR), Part 139, Certification and Operations: Land Airports Serving Certain Air Carriers, Subpart D.

3. BACKGROUND. Tiltrotor technology offers a viable city-center to city-center air transportation capability and air transportation system capacity enhancement. The potential payback exceeds by a large margin that offered by any other technology presently identified or under development.

By eventually replacing many of the fixed-wing commuter aircraft, that utilize limited runway and airport assets, and accommodating their passengers with a tiltrotor aircraft landing and taking off from vertiports or vertistops, significant system capacity can be gained. Vertiports can be on airports, operating on a simultaneous but nonconflicting basis with fixedwing traffic; urban-area vertiports located near city centers, negating the need for commuters with destinations in the urban area to even pass through the airport facilities; or smaller vertistops. Analyses conducted at three New York area airports show a replacement of only half of the commuter flights of 360 miles or less could result in a capacity gain of over 20 percent--with relatively little expenditure in additional construction when compared to the cost of new runways or airports.

Da’e: 5/31/91 *c No: 150/5390-3 Initiated by: m-10~~ Change:

With the objective of providing guidance for the construction of vertiports to meet system capacity and projected needs for civil tiltrotor operations, the FAA, with technical experts representing the industry, developed the design criteria in this AC.

Vertiport ability to support precision instrument operations with the lowest operating minimums is the objective of these design criteria. However, operating minimums are and will continue to be based on demonstrated aircraft, navigational aid, and pilot performance capabilities and limitations. The standards in this AC are based on the assumptions that manufacturers will develop a tiltrotor aircraft and navigational equipment with the demonstrated redundancy of performance to safely: (1) fly a 9-degree approach path during instrument meteorological conditions with an accuracy warranting reduced airspace, (2) decelerate to zero velocity prior to reaching the touchdown point, (3) transition from an instrument flight environment to visual environment before reaching the touchdown point, and (4) eliminate the necessity for missed approach areas and surfaces which differ from the areas and surfaces required for the approach.

A tiltrotor aircraft with navigational equipment and certified capabilities to operate safely and effiientiy within the airspace recommended by this AC--with a sustained safety level commensurate with airplane operations--will have to be developed by industry to obtain the desired operating minimums.

Leonard E. Mudd, Director Office of Airport Safety Standards

ml/91 AC 15015390-3

TABLE OF CONTENTS

TABLE OF CONTENTS

CHAPTER 1. INTRODUCTION

1. General … 1 2. Explanation of Terms … 1 3. Site Considerations … 1 4. Helicopter Usage … 2 5. Federal (FAA) Role … 2

6. State and Local Roles … 2 7. Other Sources of Technical Assistance … 2 8. Modification of Standards … 3 9. Reserved … 3 Figure l-l. Example of Vertiport Construction Notice … 4 Figure l-2. Example of a Location Map … 5 Figure 1-3. Example of a Vertiport Layout … 6 Figure l-4. Example of Notice Requirements … 7

Figure 1-3: picture of page 2Figure 1-3 · page 2
Picture of the page from the copy saved here

CHAPTER 2. AIRSIDE DESIGN

CHAPTER 2. AIRSIDE DESIGN

10. General … 11. Final Approach and Takeoff Area (FATO) … 12. Touchdown Lift-Off Surface (TLOF) … Figure 2-1. FAT0 and TLOF Relationships … Figure 2-2. A Rapid Runoff Shoulder … 13. Taxiways and Hover Taxiways … Figure 2-3. Hover Taxi Safety Area … Figure 2-4. Vertiport Taxiway … 14. Aprons and Ramps … 15. Pavement Design … Figure 2-5. Vertiport Apron or Ramp … 16. Winter Operations … 17. Fueling … 18. Fire Protection … 19. Security Requirements … 20. Other Considerations … 21-29. Reserved …

Figure 2-1: picture of page 2Figure 2-1 · page 2
Picture of the page from the copy saved here

CHAPTER 3. AIRSPACE

CHAPTER 3. AIRSPACE

30. General … 3 1. Primary Surface … 32. Approach Paths …

SECTION 1. VFR

33. Approaches - VFR … Figure 3-l. A Curved Approach Surface … Fieure 3-2. Vertinort Visual Anproach Surfaces …

9 9 9 10 10 10 10 10 10 11 11 12 12 12 12 12 12

13 13 13

13 13 14

. . . 111

SECTION 1. VFR

5r31Pl AC 15015390-3

TABLE OF CONTENTS

CHAPTER 1. INTRODUCTION

. General … 1 2. Explanation of Terms … 1 3. Site Considerations … 1 4. Helicopter Usage … 2 5. Federal (FAA) Role … 2 6. State and Local Roles … 2 7. Other Sources of Technical Assistance … 2 8. Modification of Standards … 3 9. Reserved … 3 Figure l-l. Example of Vertiport Construction Notice … 4 Figure l-2. Example of a Location Map … 5 Figure l-3. Example of a Vertiport Layout … 6 Figure l-4. Example of Notice Requirements … 7

CHAPTER 2. AIRSIDE DESIGN

CHAPTER 2. AIRSIDE DESIGN

10. General … 11. Final Approach and Takeoff Area (FATO) … 12. Touchdown Lift-Off Surface (TLOF) … Figure 2-l. FAT0 and TLOF Relationships … Figure 2-2. A Rapid Runoff Shoulder … 13. Taxiways and Hover Taxiways … Figure 2-3. Hover Taxi Safety Area … Figure 2-4. Vertiport Taxiway … 14. Aprons and Ramps … 15. Pavement Design … Figure 2-5. Vertiport Apron or Ramp … 16. Winter Operations … 17. Fueling … 18. Fire Protection … 19. Security Requirements … 20. Other Considerations … 21-29. Reserved …

Figure 2-2: picture of page 3Figure 2-2 · page 3
Picture of the page from the copy saved here

CHAPTER 3. AIRSPACE

CHAPTER 3. AIRSPACE

3 0. General … 3 1. Primary Surface … 32. Approach Paths …

SECTION 1. VFR

33. Approaches - VFR … Figure 3-1. A Curved Approach Surface … Figure 3-2. Vertinort Visual Annroach Surfaces …

9 9 9 10 10 10 10 10 10 11 11 12 12 12 12 12 12

13 13 13

13 13 14

. . . 111

Figure 3-1: picture of page 3Figure 3-1 · page 3
Picture of the page from the copy saved here

SECTION 1. VFR

AC 15015390-3 5131Pl

ParagraDh Page ” I SECTION 2. IFR

34. Approaches - Nonprecision Instrument … 14 Figure 3-3. Vertiport Nonprecision Instrument Approach Surfaces … 15 35. Approaches - 6-Degree Precision Instrument … 15 Figure 3-4. Vertiport 6-Degree Precision Instrument Approach Surfaces … 16 36. Approaches - 9-Degree Precision Instrument … 17 Figure 3-5. Vertiport 9-Degree Precision Instrument Approach Surfaces … 17 37. Protection of Imaginary Surfaces … 18 Figure 3-6. Typical Vertiport Airside and Protection Areas … 18 38-39. Reserved … 18

Figure 3-3: picture of page 4Figure 3-3 · page 4
Picture of the page from the copy saved here

CHAPTER 4. MARKING, LIGHTING, AND NAVAIDS

CHAPTER 4. MARKING, LIGHTING, AND NAVAIDS

40. General … 19 4 1. Marking … 19 42. Lighting … 19 Figure 4-l. Typical Vertiport Marking and Lighting … 20 Figure 4-2. Typical Vertistop Marking and Lighting … 21 Figure 4-3. HILS/HALS Lighting Systems … 22 43. Microwave Landing System (MLS) … 23 Figure 4-4. MLS Installation … 23 Figure 4-5. MLS Critical Area Antenna Side-by-Side … 23 44. Visual Glide Slope Indicators (VGSI) … 23 45. Wind Indicator … 23 46. Automatic Weather Observation Systems (AWOS) … 24 47. Runway Visual Range (RVR) … 24 48-49. Reserved … 24

Figure 4-2: picture of page 4Figure 4-2 · page 4
Picture of the page from the copy saved here

CHAPTER 5. VERTIPORT LANDSIDE DESIGN

CHAPTER 5. VERTIPORT LANDSIDE DESIGN

50. General … 25 51. Passenger Services … 25 52. Hangars … 25 53. Parking … 25 54. Fuel Storage … 25 55-59. Reserved … 25

CHAPTER 6. TILTROTOR FACILITIES AT AIRPORTS

60. General … 27 61. Flight Operations … 27 62. Runway-TLOF Separation … 27 63. Ground Operations … 27 64. Fueling Areas … 28 65. Passenger Transfers … 28 66-69. Reserved … 28

CHAPTER 6. TILTROTOR FACILITIES AT AIRPORTS

-

iv

s/31/91 AC 15015390-3

Paragraph

CHAPTER 7. EXAMPLES APPLYING VERTIPORT DESIGN

Page

70. General … 27 71. Commercial Service Vertiports … 27 72. A “Small” Vertiport of Vertistop … 27 73. An Elevated Private Use Vertiport … 27 Figure 7-l. A River Front Vertiport … 27 Figure 7-2. A Vertiport Spanning a Freeway … 28 Figure 7-3. A Vertiport on a Pier … 28 Figure 7-4. A Low Activity Vertistop … 29 Figure 7-5. A Rooftop Private Use Vertiport … 29

Figure 7-2: picture of page 5Figure 7-2 · page 5
Picture of the page from the copy saved here

APPENDIX 1

APPENDIX 1

Tiltrotor aircraft ( 1 page)

APPENDIX 2

Vertiport marking (1 page)

-

v (and vi)

5/31Pl AC 15015390-3

CHAPTER 1. INTRODUCTION

1. GENERAL. This chapter explains terms unique to vertiports, provides general siting guidance, and identifies sources of technical information and guidance available to persons seeking assistance in the planning and design of a civil vertiport. The standards and recommendations in this advisory circular (AC) do not limit or regulate the operations of aircraft.

CHAPTER 1. INTRODUCTION

2. EXPLANATION OF TERMS. The FAA’s Pilot/Controller Glossary in the Airman’s Information Manual (AIM) explains common aviation terms. The following are additional terms unique to vertiports:

a. Vertinort. An identifiable ground or elevated area, including any buildings or facilities thereon, used for the takeoff and landing of tiltrotor aircraft and rotorcraft.

b. Vertistop. A vertiport intended solely for takeoff and landing of tiltrotor aircraft and rotorcraft to drop off or pick up passengers or cargo.

C. Vertical Flight Aircraft. Aircraft capable of vertical or near-vertical takeoffs and landings. Vertical-lift aircraft include:

(1) Rotorcraft--rotaty-winged aircraft that lift vertically (to hover) and sustain forward flight by power-driven rotor blades turning on a vertical axis.

(2) Tiltrotor aircraft--rotorcraft with the axes of the power-driven proprotor blades capable of pivoting from vertical for vertical takeoff, landing, and hover operations to horizontal to derive lift from the wing in cruise.

(3) Tilt-wing aircraft--rotorcraft with both the wing chord and the axes of the power-driven proprotor blades capable of pivoting from vertical for vertical takeoff, landing, and hover operations to horizontal to derive lift from the wing in cruise.

(4) Fan-in-wing aircraft--fixed-wing aircraft with rotor fans in the wing to permit vertical or hover operations.

d. Rotor Span. The span (distance) between the extreme edges of the plane(s) generated by spinning rotors or proprotors.

e. Final ADDroach and Takeoff Area (FATOl. A defined area over which the final phase of the approach maneuver to a hover or landing is completed and from which the takeoff maneuver is commenced. See Takeoff and Landing Area.

f. Touchdown and Lift-Off Surface CTLOQ. The prepared (hard/paved) surface located within a FATO.

. g. Takeoff and Landing Area. The defined area whose location, size, elevation, and alignment is used in FAR Part 77 to define the lower limits of the navigable airspace for the determination of obstructions to navigable airspace which are presumed to be hazards to air navigation until an FAA airspace study determines otherwise. Takeoff and Landing Area is the regulatory term for FATO.

3. SITE CONSIDERATIONS. Tiltrotor aircraft and other vertical-lift aircraft, in addition to their ability to serve cities located up to 400 miles (644 km) apart, can operate into population centers convenient to the user’s origin and destination. Site selection should take advantage of these unique capabilities and provide convenient access to other modes of transportation or public transit.

a. Site Alternatives. Normally, vertiports or vertistops will be built at ground level. Near population centers, however, an elevated site may be more practical. Sites for elevated vertiports include: piers and docks; structures spanning interstate highways, city freeways, and railroad facilities; and the roofs of office buildings or parking garages.

b. &. The FAT0 and TLOF should be sized to accommodate the largest vertical-lift aircraft forecasted to use the facility. A large FAT0 may have multiple TLOFs whenever two or more vertical flight aircraft are to be accommodated at one time. A better alternative, however, is to provide a separate parking apron or ramp.

C. Wind Flow Around Buildings. Guidance on locating facilities to compensate for the effect of buildings on the movement of air, i.e., turbulence, etc., is found in the FAA report “Evaluating Wind Flow Around Buildings on Heliport Placement,” DOT/FAA/PM-84/25.

AC 150/5390-3

4. HELICOPTER USAGE. Although vertiports will support operations by both civil tiltrotor aircraft and civil helicopters, the design of certain vertiports where airspace is limited may make it impractical for older, less capable helicopters to operate at a particular vertiport. Design guidelines for all weather helicopter facilities (i.e., heliports and helistops with precision instrument approach capability) are contained in AC 150/5390-Z.

5. FEDERAL (FAA) ROLE. The FAA has diverse roles in the planning, design, and development of a vertiport. These include: planning recommendations, publishing design criteria, reviewing aeronautical studies and environmental assessments, and financial assistance to eligible sponsors of publicuse facilities.

a. Construction Notice.

(1) FAR Part 157, Notice of Construction, Alteration, Activation, and Deactivation of Airports, requires persons proposing to construct, activate, or deactivate a vertiport to give the FAA notice of their intent. Notice is also required when a vertiport is altered by a change in the number or size of the FATO’s or the approach departure patterns. Figures l-l through l-3 illustrate a Notice of Landing Area Proposal submission. For Item D2, Landing Area Data Layout, of FAA Form 7480-1, report the dimensions of the FAT0 as the dimensions of the Landing and Takeoff Area and the dimensions of the TLOF as the dimensions of the Touchdown Area.

(2) The FAA evaluates proposals to determine the impact upon:

(a) the safe and efficient use of the Nation’s navigable airspace,

(b) the operation of existing or proposed air navigation facilities, and

(c) the effect upon the safety of persons and property on the ground. Proponents are notified of the results of the FAA evaluation.

b. Off-Site Construction Notice. FAR Part 77, Objects Affecting Navigable Airspace, requires persons proposing to erect or alter a structure to notify the FAA of any proposed construction or alteration which would be more than 200 feet (60 m) in height, and/or any proposed construction or alteration within a horizontal

5/31Pl

distance of 5,000 feet (1 500 m) measured from the FAT0 edge of each vertlport available for public use that would penetrate an imaginary surface extending outward and upward from the FAT0 at a slope of 25 to 1. Public-use facilities are listed in the current issue of the Airport/Facility Directory. Figure l-4 illustrates situations requiring notice.

C. Financial A s s i s t a n c e . The FAA-administered grant-in-aid program provides financial assistance to qualified proponents of vertiports. The grant covers a percentage of the costs incurred in planning and constructing a public-use facility. Information concerning the FAA grant program is obtainable from any FAA airports office. Addresses for FAA airports offices are found in AC 150/5000-3, Address List For Regional Airports and Airports District/Field Offices.

d. Environmental Assessments. The National Environmental Policy Act of 1969 and FAA’s environmental review procedures require an environmental assessment be made prior to initiating actions concerning the Federal funding of vertiport development. These assessment actions usually accompany FAA approval of the proposed vertiport layout plan.

6. STATE AND LOCAL ROLES. Although in most cases, the proponents of public-use vertiports will be State or local authorities. Any proponent of a vertiport must coordinate the proposal(s) with State and local governmental agencies responsible for aviation, transportation, and land-use planning functions.

a. Notification. Some State and local governments require a favorable FAA “airspace determination” prior to issuing a permit or license to construct or operate a vertiport.

b. Assistance. State aviation authorities can provide technical advice comparable to that available from the FAA. Local planning and zoning offices should be contacted for guidance on matters of local building codes and land-use regulations affecting vertiport siting and development. Some States also have aid programs comparable to the FAA’s.

7. OTHER SOURCES OF TECHNICAL ASSISTANCE. Consultants are available to provide technical advise on vertiport design and development. Tiltrotor, tiltwing, and rotorcraft operators and manufacturers can also provide valuable input to site selection and vertiport development studies.

-

5131191 AC 15015390-3

8. MODIFICATION OF STANDARDS. Unique local conditions may justify modification of the vertiport design standards on a case-by-case basis. The request for modification must show that the modification will provide an acceptable level of safety, economy, durability, and workmanship. The dimensional values cited in paragraphs 11 and 12 are based on a projected civil tiltrotor aircraft with a lOOfoot (30 m) rotor span. While no reduction in dimensional values is recommended for public-use vertiports, paragraph 11 and 12 dimensions may be proportionally reduced for private-use vertiports on the basis of the ratio of rotor spans when the facility will be used exclusively by smaller tiltrotor/tiltwing aircraft.

9. RESERVED.

AC 15015390-3

Form ADDWM OMB No 21xun

5/31/91

36 - -_ __

Qus-b- NOTICE OF LANDING AREA PROPOSAL ,--- UME OF PROPONENT, INDIVIDUM 3R OflG*NU.A~DN 00 f;h~~mmt a Activltion

I

0 firpat i&tfalight FIqhtpul Prince William County UDRESS (ML srrwt my. Stere. ZIP cede) ; DMettnndonmnr

OF ; wkyz,-n -

County Administration Building e Vprt’ t

C. Other bndtng Areas MagneticBaafingofRumyl8)a

Washington Exed (Hyde) Maryland MCAF Quantico Manassas (Davis Field) Dulles International

Radio Tower

Occoquan Schools & Churches as depicted on Quad Attach.

hne. We. (and address II drUerenf fhan above) of person fdmg thss not- Sgnafure ( mk) type or print A. Nonymous 4-m

County Administrator

Date of Sgnakue Telephone No (Precede wi:h mx~ aMe) Jan. 10, 1991 703-444-7777

Figure l-l. Example of vertiport construction notice

5/31/91 AC 150/5390-3

Figure l-2. Example of a location map

AC 150/5390-3

\

.‘..

‘?. \

\. 2\\ r ?Q \

f

!I I Lt

.

.

. 1 , … , .

b .:

. 250’ l

. . .

Figure l-3. Example of a vertiport layout

II

ANTENNA PENETRATES SURFACE NOTICE REQUIRED

ANTENNA PENETRATES SURFACE NOTICE REQUIRED

CONSTRUCTION CRANE PENETRATES SURFACE NOTICE REQUIRED EVEN THOUGH THE BUILDING WOULD NOT PENETRATE THE SURFAC

LANDING SURFACE

AC 150/5390-3 5/31/91

5/31/91 AC 150/5390-3

CHAPTER 2. AIRSIDE DESIGN

10. GENERAL. This chapter contains airside design standards and recommendations for public-use vertiports and vertistops. For private-use vertiports or vertistops, these guidelines apply with the exception that private-use vertiports or vertistops require only an area for takeoffs and landings, i.e., a separate area for parking and loading may not be required and (a minimum of) one approach and departure path.

CHAPTER 2. AIRSIDE DESIGN

11. FINAL APPROACH AND TAKEOFF AREA JFATOl. A vertiport or vertistop must have at least one FATO. The FAT0 may contain one or more touchdown and lift-off surfaces (TLOFs). For IFR operations, the FAT0 shall contain a TLOF.

a. Dimensions. While a FAT0 may have any shape, it must be capable of circumscribing a square with 250-foot (75 m) sides. A minimum size FAT0 is illustrated in Figure 2-l. To compensate for elevation at locations where the elevation of the FAT0 is in excess of 1,000 feet (300 m), the FAT0 length should be increased by 50 feet (15 m) per l,OOO-foot (300 m) of elevation above MSL. When site conditions permit, larger FATOs are recommended.

b. Surface. The surface of the FAT0 shall be free of objects that would adversely affect the takeoff or landing of tiltrotor aircraft and be resistant to the effects of rotor downwash.

C. Alignment. The primary axis should be aligned to provide maximum wind coverage. Guidance on wind coverage is contained in AC 150/5300-13, Airport Design.

d. FATOs shall be clear of objects Clearing. except those whose locations are fixed by function. Objects fixed by function shall be located as far as possible from the TLOF and shall be frangible or mounted on low impact resistant supports.

e. Gradients. The slope in any direction in the unpaved portion of a FAT0 shall be between 1.5 and 5 percent. The maximum slope of paved portions of the FAT0 should not exceed 1 percent.

f. Elevated Vertiports and Vertistops. A full size load bearing FAT0 is recommended for elevated public-use facilities. Elevated private-use vertiports or vertistops may have portions of the FAT0 extend into unobstructed airspace beyond the edge of the building or platform.

12. TOUCHDOWN LIFT-OFF SURFACE (TLOF& The TLOF, normally located within a FATO, is a hard or paved surface capable of supporting the heaviest tiltrotor or other vertical-lift aircraft expected to use the facility.

a. Dimensions. While a TLOF may have any shape, the minimum TLOF must be capable of circumscribing a square with lOO-foot (30 m) sides for VFR and 150-foot (45 m) sides for IFR operations. An elongation of the TLOF [up to 400 feet (120 m)] offers significant operational and economic benefits and is recommended whenever site conditions permit.

b. Location. Normally, the TLOF is centered in the FAT0 with its primary axis centered on the final approach course. If not centered, there must be at least 75 feet (22.5 m) of clear space between the edges or ends of the TLOF and the edge of the FATO. For IFR operations, the TLOF must be located in the FAT0 with its primary axis centered on the final approach course. Figure 2-l illustrates TLOF and FAT0 spatial relationships.

C. Gradients. Longitudinal and transverse gradients of a TLOF should not exceed 1 percent. Vertical curves should be used on elongated TLOFs to eliminate abrupt changes in grade. A rapid runoff shoulder, as illustrated in figure 2-2, is recommended adjacent to the paved surface. Vertiports with significant number of operations should have paved shoulders, 25 foot (7.5 m) wide, to minimize the effect of exhaust heat and proprotor downwash on unpaved areas surrounding the TLOF.

d. Raised TLOFs. TLOF surfaces 4 feet (1.2 m) or more above the level of the FAT0 must have a 5 foot (1.5 m) wide horizontal safety net or shelf installed around the TLOF. The safety net or shelf, capable of supporting the weight of a person, should be at or below the surface of the TLOF.

AC 150/539@3

* Minimum 75’(22.5 In) Clearance

[ FAT0 1

TLOF ILLI *

TLOF ILLI *

M I N I M U M S I Z E

FATO/TLOF

FAT0

- /I ’

* A ELONGATED FATO/TLOF

\

O D D S H A P E D FAT0 / M I N I M U M crLoF

Figure 2-l. FAT0 and TLOF relationships

Figure 2-2. A rapid runoff shoulder

5/31/91

13. TAXIWAYS AND HOVER TAXIWAYS. A taxiway or hover taxiway connecting a TLOF to an apron or ramp used for passenger service, to a - maintenance or storage hangar, to refueling locations, and to aircraft tiedown (parking) positions must be obstacle free. Figures 2-3 and 2-4 illustrate a taxiway and a hover taxiway.

* A ELONGATED FATO/TLOF

a. Taxiway/Hover Taxiway Safetv Areas. A ground taxiway requires a cleared safety area 150 feet (45 m) wide. The safety area for a hover taxiway is 250 feet (75 m) wide.

Figure 2-3. Hover taxiway safety area

b. Taxiways. Paved taxiways should be 75 feet (22.5 m) wide to assure that the engine exhaust is directed onto a heat and blast resistant surface. For economy, a taxiway may be constructed with a loadbearing center section equal to the aircraft’s gear width plus 20 feet (6 m). The pavement, outboard of

the loadbearing center section, must be capable of resisting the effects of the exhaust stream but may be of lesser structural strength.

Figure 2-4. Vertiport taxiway

-

Figure 2-3: picture of page 15Figure 2-3 · page 15
Picture of the page from the copy saved here

C. Clearances. At least one-half the tip-totip span, but not less than 25-feet (7.5 m), separation should be provided between the limit of the rotor span of an aircraft and a fixed or movable object with the aircraft’s undercarriage 15 feet (4.5 m) from the edge of the taxiway. For hover taxiing, there should be 75 feet (22.5 m) of clearance between the limit of the rotor span of an aircraft on centerline and a fixed or moveable object.

Gradients. The gradients of paved taxiways (longikdinal and transverse) should not exceed 2 percent. Transverse grades of up to minus 3 percent are permitted in unpaved portions of a taxiway safety area.

e. Parallel Taxiwavs. The minimum distance between the centerline of an elongated TLOF and the centerline of a parallel taxiway, or between centerlines of parallel paved taxiways, is 200 feet (60 m).

14. APRONS AND RAMPS. Aprons or ramps for loading or unloading, parking, fueling, or servicing aircraft are sized to accommodate the number and type of aircraft which are expected to use the facility during peak activity periods.

a. Clearances. Aircraft parking positions should provide a minimum of one-half the tip-to-tip span, but not less than 25-feet (7.5 m), separation between the limits of rotor spans of adjacent aircraft, or between the limit of the rotor span of an aircraft and a fixed or moveable object. Figure 2-5 illustrates recommended apron and ramp clearances.

b. Gradients. Apron or ramp longitudinal and transverse gradients should be sufficient to assure positive runoff, but should not exceed 2 percent in any direction. Apron or ramp catchbasins should be located clear of passenger walkways.

C. Apron Edge Taxiways. The centerline of an apron or ramp edge taxiway should be located according to the guidelines in paragraph 13.

15. PAVEMENT DESIGN. The TLOF, taxiway, and apron or ramp must be designed to be capable of supporting the heaviest tiltrotor or other aircraft expected to use the facility. FAA AC 150/5320-6, Airport Pavement Design and Evaluation, provides technical guidance on pavement design. Designs must consider the following:

c

AC 15015390-3

Figure 2-5. Vertiport apron or ramp

Figure 2-5: picture of page 16Figure 2-5 · page 16
Picture of the page from the copy saved here

a. Static and Dvnamic Loads. Assume dynamic loads imposed by the most critical aircraft expected to use the facility at 150 percent of the aircraft’s static load (weight) with 75 percent of that load distributed equally through the aircraft’s main landing gear. Appendix 1 provides information on tiltrotor aircraft proposed weights. AC 150/5390-2, Heliport Design, provides similar information for helicopters. Static loads imposed by service vehicles also need to be considered when designing elevated facilities.

b. Dust and Debris. Constructing light duty paved shoulders 25 to 35 feet (7.5 to 11 m) wide around all operational surfaces will help to alleviate dust and debris from being blown about by the downwash from proprotors or rotors.

C. Engine Exhaust. Materials resistant to high temperatures should be used to minimize the effect of a tiltrotor’s exhaust heat and velocity damaging or eroding the pavement or pavement joints.

AC 150/5390-3

16. WINTER OPERATIONS. Snow and ice removal is important for winter operations. Because of the strong downwash from landing or departing tiltrotor aircraft or rotorcraft, snow should be removed from the entire FATO, the taxiway safety area, and the apron or ramp area. The size of the area to be cleared of snow and ice and the frequency of snow fall will determine the method of control or removal used. At very small vertiports, in-pavement heating may be worthy of consideration. Plowing, deicing, and anti-icing may be more economical at larger vertiports. AC 150/5200-30, Airport Winter Safety and Operations, provides guidance on this subject.

17. FUELING. Fueling services may be carried out through a hydrant system located at parking positions, by trucks moving to the aircraft, or by aircraft moving to a centralized refueling location. If fuel trucks are used, the vertiport should be designed to minimize the need for them to operate on the FATO, TLOF, or taxiway system. Guidance for locating fueling areas to compensate for effects of buildings is found in “Evaluating Wind Flow Around Buildings on Heliport Placement,” DOT/FAA/PM-84/25. If winds in the fueling area differ significantly from winds elsewhere on the vertiport, a wind indicator should be located in the fueling area. Hoses for hydrant systems or central fueling systems should be long enough to reach the largest aircraft expected at the vertiport while parked at the gate or fueling position.

a. Grounding Rods. Recessed grounding rods should be installed at all fueling locations.

b. Code Requirements. Fueling systems must comply with national and local codes and/or ordinances for flammable liquid storage and handling. Environmental considerations require that spilled fuel not contaminate water supplies or be discharged into sewer systems.

18. FIRE PROTECTION. Vertiports having scheduled passenger service meeting the conditions stipulated in Title 14, Code of Federal Regulations (14 CFR), Part 139, Certification and Operations: Land Airports Serving Certain Air Carriers, must comply with the fire protection requirements contained therein. Other vertiports and vertistops should apply the fire protection standards promulgated by the National Fire Protection Association (NFPA) and/or the fire protection requirements imposed by the local authority having jurisdiction.

19. SECURITY REQUIREMENTS. To ensure public and passenger safety, all operational areas of a vertiport must be secured to prevent unauthorized entry. The simplest system is a fence preventing access to vertiport operational, maintenance, and fuel storage areas. However, the fence should be located so that it does not become a hazard to flight operations. Legitimate access is through locked or manned gates. By their nature, elevated vertiports usually have simpler security requirements--their primary need being control of passenger movement. Refer to FAR Part 107, Airport Security, for requirements at vertiports having scheduled commercial service.

20. OTHER CONSIDERATIONS.

a. Vehicle Traffic. Mark traffic lanes used by fuel trucks and other support vehicles operating on the apron or ramp to prevent an incident or accident involving vehicles and moving or parked aircraft.

b. Aircraft Tiedowns. Tiedowns are recommended to secure parked aircraft to withstand the forces of unexpected winds. Tiedowns are particularly important for elevated facilities or vertiports or vertistops without hangars. Information on designing aircraft tiedowns is found in AC 20-35, Tiedown Sense.

C. Marking Wires. To assure aeronautical conspicuity, overhead wires in the vicinity of a vertiport should be marked with spherical markers except when an FAA aeronautical study finds that the absence of such markers will not impair aviation safety. Markers should identify overhead wires:

1) above a plane having a slope of 16 to 1 (horizontal to vertical) which rises from each edge of the FAT0 for a horizontal distance of 150 feet (45 m) from the FAT0 edge.

2) above a trapezoidal-shaped plane having a slope of 16 to 1 (horizontal to vertical) under the approach surface. The plane is 1,600 feet (480 m) long and extends 100 feet (30 m) outward beyond each edge of the approach surface.

21-29. RESERVED.

5/31/91 AC 150/5390-3

CHAPTER 3. AIRSPACE

CHAPTER 3. AIRSPACE

30. GENERAL. This chapter contains airspace considerations for vertiports and vertistops. Imaginary surfaces associated with vertiport airspace are the primary surface, approach surfaces, and transitional surfaces. The size and configuration of these surfaces are dependent on location, size, elevation, and alignment of the takeoff and landing areas and the conditions under which operations are anticipated, i.e., visual operating rules (VFR) or instrument operating rules (IFR); and the type of approach associated with operations under those conditions, i.e., visual, nonprecision instrument, and precision instrument approaches. Precision approach surfaces are also highly dependent upon the angle of the approach, equipage of the aircraft, and proficiency and training of the air crews.

31. PRIMARY SURFACE. The primary surface is a horizontal plane having the size and shape of the FATO. It is at the elevation of the highest point on the TLOF(s). It abuts the inner edge of the approach surface, and for IFR, may extend beyond the FATO. The FAT0 is the same as the designated takeoff and landing area referenced in FAR Part 77. l

32. APPROACH PATHS. Regardless of meteorological conditions under which operations are anticipated and the type of approach, public-use vertiports should have two or more object-free approach paths. Vertiport approach paths should be selected to maximize operations into prevailing winds and to minimize operations over noise sensitive areas.

SECTION 1. VFR

SECTION 1. VFR

33. APPROACHES - VFR. The following surfaces, illustrated in figure 3-2, provide protection for visual approaches.

a. Approach Surfaces. The approach surface begins at the edge of the primary surface, where it has the same width as the primary surface, and extends outward and upward for a horizontal distance of 4,000 feet (1 200 m) where its width is 650 feet (195 m). The slope of the approach surface is 8:l (horizontal to vertical).

b. Transitional Surfaces. Transitional surfaces extend outward and upward from the lateral boundaries of the primary surface and the approach surface. The planes slope upward at a ratio of 2:l (horizontal to vertical) for a distance of 325 feet (9s m) measured horizontally from the centerline of the primary and approach surfaces.

C. Curved Approach Surface. While the outer portion of an approach surface may curve, the final 1,200 foot (360 m) segment abutting the primary surface is straight. Figure 3-1 illustrates a curved approach surface.

Figure 3-l. A curved approach surface

AC 15015390-3 5131191

-

t

- 650’<195 m)-

clI D R A W I N C N O T T O S C A L E

250’<75 M) MINIMUfi 4

Figure 3-2. Vertiport visual approach surfaces

SECTION 2. IFR

34. A P P R O A C H E S - NONPRECISION INSTRUMENT. Most operations are VFR. Additional operations can be performed with a nonprecision instrument approach procedure to a point in space.

Figure 3-2: picture of page 19Figure 3-2 · page 19
Picture of the page from the copy saved here

SECTION 2. IFR

a. Procedures To a Point In Space. Nonprecision instrument operations can be conducted to a point in space. Weather permitting, a pilot may discontinue the instrument procedure and continue VFR to the vertiport. Under these conditions, the VFR surfaces defined in section 1 apply.

b. Procedures To The Vertiport. The following surfaces, illustrated in figure 3-3, provide protection for the visual segment of nonprecision instrument approaches to a vertiport. A vertiport’s ability to support low landing minima is sometimes limited by obstructions in the missed approach segment.

(1) Approach Surface. The approach surface begins at the approach end of a primary surface of at least 300 feet (90 m) in length and width, where it has a width of 500 feet (150 m) and

extends outward and upward for a horizontal distance of 5,000 feet (1 500 m), where its width is 2,000 feet (600 m). The slope of the approach surface is 2O:l (horizontal to vertical).

(2) Transitional Surfaces. Transitional surfaces extend outward and upward from the lateral boundaries of the primary surface and the approach surface. The planes slope upward at a ratio of 4:l (horizontal to vertical) for a distance of 350 feet (105 m) measured horizontally from the boundaries of the primaty surface; and the distance varies along the boundaries of the approach surface from 350 feet

(105 m) at the primary surface end and narrows to 0 feet at 2,000 feet (600 m) from the primary surface.

(3) Missed Approach Surfaces. The missed approach surface originates below the missed approach point and has a rising slope of 2O:l. Any object penetrating the slope requires an adjustment of the minimum descent altitude. The dimensions of the missed approach area (including the radius of turn) vary with the type of missed approach. (Further guidance may be found in FAA Handbook 8260.3B.)

5131191 AC 15015390-3

D R A W I N G N O T TO S C A L E

2 . 0 0 0 l < 6 0 0 rn)?

II

* 3 0 0 - (90 m) M I N I M U M *I* 3 5 0 *(105 m> *.c* 5 0 0 ’<150 m) ir**2,000’<600 m>

Figure 3-3. Vertiport nonprecision instrument approach surfaces

35. APPROACHES - 6-DEGREE PRECISION INSTRUMENT. The following surfaces apply to vertiports designed to accommodate 6- and/or 4degree approaches for precision instrument operations. While most helicopters capable of precision instrument flight are certificated to fly 4degree precision approaches, by modification and/or recertification, they may fly 6-degree approaches. The 6-degree approach surface is illustrated in figure 3-4.

taper uniformly to a 600 foot (180 m) width at the 1,225-foot (373 m) point. The transitional surfaces rise at a slope of 7:l (horizontal to vertical).

a. Approach Surface. The approach surface is an imaginary trapezoidal-shaped plane. It begins

1,225 feet (373 m) from the back of the IFR FAT0 and extends outward for 25,000 feet (7 500 m) along the final approach course. It flares from a beginning width of 1,000 feet (300 m) to an ending width of 6,000 feet (1 800 m). The surface slopes upward at a ratio of 17:l for a 6-degree glide slope and 25.5:1 for a 4-degree glide slope.

C. Obstacle Free Zone (OFZ). The OFZ consists of the IFR FAT0 (the approach OFZ) and the inner-transitional surfaces. The IFR FAT0 is 300 feet (90) m) wide by 1,225 feet (373 m) long. The inner-transitional surfaces extend out from the IFR FAT0 at a slope of 7:l measured perpendicular to the IFR FAT0 for a distance of 350 feet (105 m).

b. Transitional Surfaces. At 25,000 feet (7 500 m) from the 1,225-foot point, the surfaces are 1,500 feet (450 m) wide, measured from the outer edge at right angles to the final approach course, and

d. Missed Annroach Surfaces. A vertiport’s ability to support low landing minima may be limited by obstructions in the missed approach segment. The missed approach surface originates 1,500 feet (450 m) beyond the decision point and rises at a slope of 2O:l. Any object penetrating the slope requires an adjustment of the minimum descent altitude. The dimensions of the missed approach area (including the radius of turn) vary with the type of missed approach. Details of missed approach surfaces may be developed with an FAA procedures specialist.

AC 150/5390-3 5/3lPl

-.

SEE ENLAROEMENT

l ’ ’ 25,000’(7 500 m)

\

INNER TRANSITIONAL.r

SURFACE 7:1

1 \ 350 ’ Cl.05 m

1,225’ (373 In)1. 300 - <90 m IFR FAT0 J /

r

+ 350 * (105 n-8 /

INNER TRANSITIONAL, SURFACE 7:l.

I

t MI.9.9ED i 0 0 I D E C I S I O N P O I N T

II ” A P P R O A C H I SURFACE 17:1 0 A P P R O A C H

SURFACE 7:1

: 0 SURFACE 20: 1 /-.d,500.wo m,-aJ

I

Figure 3-4. Vertiport 6-degree precision instrument approach surfaces

5/31/91

36. APPROACHES - 9-DEGREE PRECISION INSTRUMENT. The objective of these criteria is to design a vertiport with the ability to support precision instrument operations with the lowest possible operating minima. Operating minima are and will continue to be based on demonstrated aircraft, navigational aid, and pilot performance capabilities and limitations.

a. Assumptions. The standards in this paragraph are based on the assumptions that manufacturers will develop a tiltrotor aircraft and navigational equipment with the demonstrated redundancy of performance to safely:

(1) fly a 9-degree approach path during instrument meteorological conditions with an accuracy warranting this reduced airspace,

(2) decelerate to zero velocity prior to reaching touchdown point,

(3) transition from an instrument flight environment to visual environment before reaching the touchdown point, and

Figure 3-4: picture of page 21Figure 3-4 · page 21
Picture of the page from the copy saved here

(4) eliminate the necessity for missed approach areas and surfaces which differ from the areas and surfaces required for the approach.

The dedicated approach area for these improved capabilities is illustrated in figure 3-5.

AC 15015390-3

b. Approach Surface. The approach surface is an imaginary trapezoidal-shaped plane. It begins at the edge of, and at the width of the primary surface (250 feet (75 m) square), flaring to a width of 3,000 feet (900 m) in a horizontal distance of 10,000 feet (3 000 m). The trapezoid slopes upward at a ratio of 1O:l (horizontal to vertical).

C. Transitional Surfaces. Transitional surfaces slope outward and upward from the edges of the primary surface and the precision approachbsurface.

(1) The transitional surfaces adjacent to the primary surface slope upward and outward at a ratio of 3:l (horizontal to vertical). These planes have a horizontal width of 600 feet (180 m).

(2) Transitional surfaces also rise from the edges of the precision approach trapezoid at a ratio of 7:l (horizontal to vertical). These planes have a horizontal width of 600 feet (180 m) at the beginning of the approach trapezoid and flare to a horizontal width of 960 feet (293 m) at the outer end of the approach surface.

d. Missed Approach Surfaces. Missed approach surfaces are not prescribed since the missed approach must be flown within the approach airspace.

Figure 3-5. Vertiport 9-degree precision instrument approach surfaces

AC 150/5390-3 5/31/91

37. PROTECTION OF IMAGINARY SURFACES. Vertiport designers and operators should maximize Vertiport proponents should own--or have control use of the available airspace over rivers, highways, over--the surface under the approach, departure, and railroads, etc. Ideally, the protected zones will be transitional surfaces out to the point where the imaginary surfaces are at least 35 feet (11 m) above

Figure 3-5: picture of page 22Figure 3-5 · page 22
Picture of the page from the copy saved here

cleared of all objects not essential to flight operations. If clearing is impractical, acceptable use is limited to the elevation of the highest point on the TLOF(s). Figure 3-6 illustrates the typical surface areas which should be owned or controlled to provide airside and close-in airspace protection for vertiports designed for VFR and IFR (with 6- and 9-degree approach angles)

those activities which do not lead to the congregation of people. Protection through acquisition, supplemented by height and land-use zoning beyond the boundaries of the vertiport, is recommended.

operations.

Figure 3-6: picture of page 23Figure 3-6 · page 23
Picture of the page from the copy saved here

V F R V E R T I P O R T

V F R V E R T I P O R T

38-39. RESERVED.

I F R VER’I’IPORT

W I T H 9= APPROACHES

R VERTIPORT WITH 6” APPROACHES

Figure 3-6. Typical vertiport airside and protected areas

-

5/31/91 AC 15015390-3

CHAPTER 4. MARKING, LIGHTING, AND NAVAIDS

40. GENERAL. This chapter contains standards and recommendations for marking, lighting, and siting NAVAIDs on public-use vertiports and vertistops.

CHAPTER 4. MARKING, LIGHTING, AND NAVAIDS

41. MARKING. Painted lines, numerals, and letters or raised boundary markers identify vertiport and vertistop surfaces. To increase conspicuity on light colored pavements, white markings should be edged with a 6 inch (15 cm) wide black line. Figures 4-l and 4-2 illustrate marking recommendations.

a. FAT0 The limits of the FAT0 should be defined wit-ground edge markers placed at the corners and at intervals of approximately 125 feet (37 m) along the FAT0 edges. Alternatively, raised markers, no more than 6 inches (15 cm) high, may be used in lieu of the recommended in-ground markers. Edges of a paved FAT0 are defined with 16 inch (40 cm) wide painted white lines.

b. TLOF The edges of the TLOF are defined with6 inch (40 cm) wide painted white line not more than 1 foot (30 cm) in from the TLOF edge. When the length of the TLOF is more than three times its width, the TLOF has a centerline marked with 50 foot (15 m) long 16 inch (40 cm) wide painted white lines separated by 25 foot (7.5 m) spaces. The centerline begins 25 feet (7.5 m) from the numerals indicating the magnetic heading. Based on the elongated length, the length of the centerline stripes and spaces shall be reduced proportionally.

1) The distinctive marking shown in this AC is recommended for identifying a vertiport. Dimensions for the marking, suitable for a 100 foot (30 m) wide TLOF, are found in Appendix 2. The marking is centered on a square TLOF and is 20 feet (6 m) in from the end of an elongated TLOF. A one or two digit number, at least one-half the size of the symbol, reflecting the nearest 10 degrees of magnetic heading of the approach, identifies the ends of an elongated TLOF.

2) On a vertiport or vertistop, where the maximum aircraft weight and rotor span is restricted, the restriction is indicated in the near right corner of the TLOF. See figure 7-5. The number above a bar indicates the maximum aircraft weight in thousands of pounds. The number below the bar indicates the maximum rotor span in tens of feet.

C. Taxiwavs. All taxiway markings are yellow. Taxiway centerlines are marked with a 6 inch (15 cm) wide line. Taxiway edges are marked with double 6 inches (15 cm) wide lines spaced 6 inches (15 cm) apart. That portion of taxiway pavement that is not full strength is marked with yellow 3 foot (1 m) wide bars perpendicular to the taxiway centerline at intervals not in excess of 30 feet (9 m).

d. Hover Taxi Routes. Cylindrical raised markers are used to define the outer edges of the hover taxi route safety area. Markers should be 3 feet (1 m) in height, be retroreflective, and provide maximum color contrast with the natural background.

e. Aprons and Ramps. Six inch (15 cm) wide yellow lines may be used to guide aircraft into each

intended parking position. Parking positions (gates) may be identified by a letter or number.

f. Passenger Walkwavs. An enclosed boarding ramp is recommended for the safety, comfort, and convenience of passengers. In the absence of a boarding ramp, a 5 foot (1.5 m) wide walkway should be painted to define a safe path between parked aircraft and the terminal building or exit gate.

42. LIGHTING. Vertiports are lighted with standard aviation lighting fixtures. Shielded floodlights may be used to illuminate passenger boarding positions on the apron. Figures 4-l through 4-3 illustrate vertiport lighting.

a. The limits of a ground level FAT0 FATO. need not be lighted if the TLOF is lighted. On elevated vertiports or vertistops, an odd number of L-810 red double lens obstruction lighting fixtures are used to mark the edges of the building. FAT0 or building edge lights should be spaced approximately 50 feet (15 m) apart.

b. TLOF An odd number, but not less than five L-86lzw omni-directional lights located at least 10 feet (3 m) out from the pavement edge, define a TLOF, or the limits of a FATO. Lights should be flush mounted if located on a paved surface. On other surfaces, lights should be as low as practical--preferably not more than 8 inches (20 cm) high. The typical 100 x 100 foot (30 x 30 m) TLOF requires 16 lights (5 lights per side) spaced approximately 30 feet (9 m) apart.

AC 150/5390-3 5/31/91

A

r A

A

AAA.

I

.

.

I .

.

.

I

.

A

27 cp-l

1

l AAA

g-:

I

.

.

.

.

L E G E N D

L E G E N D

- EDGE MARKER

I l

ELEVATED EDGE LIGHT

Id, ADDITIONAL EDGE LIGHT

a HILS WING & EDGE BARS

9 TAXIWAY CENTERLINE LIGHT

.

I

A A L - A A

A A

J

Figure 4-l. Typical vertiport marking and lighting

5/31/91 AC 150/53!W3

THIS HALF OF DRAWING ILLUSTRATES RAISED EDGE MARKERS 6 ELEVATED LIGHTS

THIS HALF OF DRAWING ILLUSTRATES RAISED EDGE MARKERS 6 ELEVATED LIGHTS

w l'(30 c m )

b C,

0 c -4 .

0

I””

0,

0 k 16°C

PAINTED

4 0 cm) WHITE LINE

THIS HALF

IN-GROUND

OF DRAWING ILLUSTRATES MARKERS & INSET LIGHTS

I J L IJ

LEGEND - RAISED EDGE MARKER - IN-GROUND EDGE MARKER

0 ELEVATED EDGE LIGHT

0 INSET EDGE LIGHT

Symbol Size Exaggerated for Clarity

Figure 4-2. Typical vertistop marking and lighting

0 INSET EDGE LIGHT

AC 15015390-3 5/31Pl

C. Taxiwavs. L-861 blue taxiway lights, not more than 8 inches (20 cm) high, define taxiway edges. The lights are located 10 feet (3 m) out from the edge of the full strength pavement. Alternatively, inset L-852 green bidirectional lights may be used to mark the centerline of a paved taxiway, including a taxiway located on an apron or ramp. Where centerline lights are installed, blue retroreflective markers may be used to delineate the edges of the full strength taxiway pavement. Lights and/or retroreflective markers should be spaced approximately 50 feet (15 m) apart.

d. Hover Taxiwavs. The edges of the hover taxiways are defined with L-861 blue taxiway lights spaced not more than 50 feet (15 m) apart.

e. Apron or Ramp. Aprons or ramps may be illuminated with floodlights located so that the mounting poles are not hazardous to aircraft operations. Floodlights must also be shielded to prevent unwanted glare in the eyes of pilots while approaching to land, while departing, or while maneuvering the aircraft on the apron or ramp.

f. Vertiport Beacon. A lighted vertiport should have an identification beacon flashing whitegreen-yellow pulses of light. The beacon should be located on or immediately adjacent to the vertiport. It must be placed so that it will not penetrate an approach, departure, or transitional surface nor have the beam interfere with pilot or controller vision (see AC 150/5345-12, Specification for Airport and Heliport Beacons).

!3 Parking Positions. Yellow bidirectional inset lights located at 10 foot (3 m) intervals may be used to delineate parking position guidance lines.

h. Enhanced Lighting Svstems. The basic FAT0 and/or TLOF lighting installation must be enhanced in order for the vertiport to have a precision instrument approach procedure. This enhanced system includes high intensity lights (HILS) and an approach lighting system (HALS).

1) The HILS, illustrated in figure 4-3, consists of PAR 56 lights which extend the TLOF edge lights. The system extends both the right and left edge lights as “edge bars” and the front and rear edge lights as “wing bars.”

2) The HAL& illustrated in figure 4-3, consists of PAR 56 lights and has a length of

1,000 feet (300 m).

HILS EDGE BAR 3 LIGHTS

A A

Q SO’(15 m) - -

AAA.*...*.*.AAA I .

HILS WING BAR . :

3 LIGHTS @ lS’(4.5 m) l .

AAA...s.a.e.AAA

A . A

A A

.

z . .

8 LEGEND . ELEVATED EDGE ADDITIONAL EDGE d : HILS FIXTURES &, 1 HALS FIXTURES

HILS EDGE BAR 3 LIGHTS

w” E ?I . . . . 2s . . . .

. . . ”

Figure 4-3. HILSMALS lighting systems

43. MICROWAVE LANDING SYSTEM (MLS). The MLS is the only practical navigational system currently available for a precision instrument approach to a vertiport. It consists of an azimuth (AZ) antenna, an elevation (EL) antenna, and precision distance measuring equipment (PDME).

a. Antenna Siting. The AZ and EL antennas are normally sited within the areas illustrated in figure 4-4. The PDME antenna is usually located with the AZ antenna. Proponents should consult with an FAA regional office for guidance on siting MLS antennas and monitors.

I-r

i

I

I -1

-4ocrflPm)-

h - 25

I .g ’ ! : I \

Q --------- - - - - - - - - - ;’ A ; I-i I-i

* . i ii ; ii

4 + 4 , I i: I ii j----~clsm)---7 j----2%7(75m)-: t :-* __.-.. *_- :-* __.-.. *_-t ---.._--- &l ---.._--- &l

+

+

L - . -- _ _ ^ .------ . ---* .-e -. . _--- *- _ --a-( L 404 (l2Om)U

Figure 4-4. A MLS installation

Figure 4-3: picture of page 27Figure 4-3 · page 27
Picture of the page from the copy saved here

b. MLS Critical Areas. Signal reflections off vehicles in the MLS critical areas can adversely affect the MLS signal. The MIS critical area must be clear of aircraft, fuel trucks, etc., whenever an aircraft is executing an IFR approach. Figure 4-5 illustrates typical MLS critical areas.

AC 15015390-3

Figure 4-5. MIS critical area/

antennas side-by-side

44. VISUAL GLIDE SLOPE INDICATOR (VGSIl. VGSIs include the Visual Approach Slope Indicator (VASI), the Precision Approach Path Indicator (PAPI), or the Pulse Light Approach Slope Indicator (PLASI). AC 150/5345-28, Precision Approach Path Indicator, provides guidance on siting and aiming VGSIs.

a. A VGSI is recommended at all vertiports anticipating night operations.

b. A VGSI is required at vertiports with a nonprecision or precision instrument approach procedure.

Figure 4-5: picture of page 28Figure 4-5 · page 28
Picture of the page from the copy saved here

45. WIND INDICATOR. A wind indicator/wind cone is required. The indicator must be visible to pilots of aircraft approaching to land as well as to pilots taxiing into position for takeoff. It should be positioned so that it provides an accurate indication of the wind conditions in the vicinity of the TLOF but should not penetrate an approach, departure, or transitional surface. Indicators must be lighted for night operations. It may be desirable to install wind indicators at several locations on a vertiport when the wind flow variations in different parts of the vertiport are operationally significant.

AC 150/5390-3 5/31Pl

46. AUTOMATIC WEATHER OBSERVATION SYSTEMS (AWOSl. An AWOS may be required at a vertiport to obtain lower operational minima. Guidance on AWOS installations is found in AC 150/5220-16, Automated Weather Observing Systems (AWOS) for Non-Federal Applications.

47. RUNWAY VISUAL R A N G E (RVRl. Visibility information is required for low visibility operations. The RVR installation provides a measurement of horizontal visibility, i.e., how far ahead the pilot of an aircraft should be able to see a high intensity vertiport edge/boundary light.

48-49. RESERVED.

5/31/91 AC 15015390-3

CHAPTER 5. VERTIPORT LANDSIDE DESIGN

CHAPTER 5. VERTIPORT LANDSIDE DESIGN

50. GENERAL. Vertiport landside features such as: passenger services (terminal and parking), hangars, employee parking, fuel storage, etc., vary from site to site. Ground space required for these features is in addition to the ground space required for airside activities. At elevated vertiports, some of these facilities and services may be located on floors one or more levels below the level of the airside surface. Vertistop landside requirements may consist of a passenger waiting area and a modest parking area. Landside facilities should be functional, attractive, and capable of orderly expansion as future needs develop. AC 150/5360-9, Planning and Design of Airport Terminal Facilities at Non-Hub Locations has guidance on terminal design.

51. PASSENGER SERVICES. The type and extent of services provided to/for passengers dictates the space requirements. Airline operators will need space for administrative purposes in addition to space for passenger ticketing, waiting, and baggage makeup and retrieval. To the extent practical, permit passenger boardings to be carried out through enclosed passageways.

52. HANGARS. Normally, hangars for aircraft storage and/or maintenance would be provided at locations other than a space constrained city-center vertiport. At unconstrained facilities, locate hangars so that they will not penetrate any existing or future approach, departure, or transitional surface. Hangar sites should not compromise plans for terminal expansion or improved passenger services.

53. PARKING. Parking is required for passengers, employees, and other tenants. Employee and/or longterm passenger parking needs should not preempt space best used for short-term parking. Vehicle congestion might be minimized by locating the vertiport close to public mass transit.

54. FUEL STORAGE. Fuel storage sites and facilities must conform with all applicable local codes and ordinances on the subject. A C 15015230-5, Aircraft Fuel Storage, Handling, and Dispensing on Airports, contains guidance on fuel handling and storage

55-59. RESERVED.

-

CHAPTER 6. TILTROTOR

CHAPTER 6. TILTROTOR

60. GENERAL. Capacity demand or operational constraints because of a significant number of tiltrotor and/or rotorcraft operations at an airport will justify development of separate landing and takeoff facilities for their exclusive use. When tiltrotor and/or rotorcraft operations do not justify separate facilities, an analysis should be conducted to ensure that the airport’s runway(s) and terminal or apron area configuration and the proposed location of tiltrotor and rotorcraft operating areas will allow tiltrotor and rotorcraft to operate safely.

a. Tiltrotor Operations. The facilities developed exclusively for tiltrotor operations should conform to the standards and recommendations found in chapters 2, 3, and 4 of this AC.

b. Rotorcraft Operations. The facilities developed exclusively for rotorcraft operations should conform to the standards and recommendations found in AC 150/5390-2, Heliport Design.

61. FLIGHT OPERATIONS. Approach paths and traffic patterns for the airport’s fixed-wing aircraft are fixed by the configuration of the runways. Because tiltrotor and rotorcraft do not need runways, their approach paths may converge, diverge, or parallel the paths used by fixed-wing airplanes.

a. Independent Flight Paths. The approach paths for tiltrotor and rotorcraft instrument operations must take into account and be compatible with the approach paths used for fixed-wing operations.

b. Dependent or Common Flight Paths. Until sufficient demand exists or is forecast, and in the absence of capacity constraints, existing runways and navigational aids will accommodate tiltrotor and rotorcraft operations.

C. Coordination Required. The approach path(s) identified for tiltrotor and rotorcraft use should be developed as a coordinated effort involving the FAA, airport management, and aircraft operators. If new flight paths are expected to overlie previously unaffected residential areas, persons representing those adjacent residential areas should be included in the coordination process.

AC 150/5390-3

FACILITIES AT AIRPORTS

62. RUNWAY-TLOF SEPARATION. The potential impact of downwash generated by tiltrotors and rotorcraft on parked and taxiing light aircraft must be factored into the design and location of the TLOF.

a. Visual Operations. The recommended minimum separation between the center of the TLOF and the centerline of a runway for strictly visual operations is 700 feet (210 m).

FACILITIES AT AIRPORTS

b. Instrument Operations. The minimum TLOF to runway separation for independent nonprecision or precision instrument operations must be developed in consultation with the appropriate FAA offices.

C. FATOs/TzOFs on Aprons or Ramps. Tiltrotor and rotorcraft visual operations may be accommodated on a corner of an apron or ramp provided this area is within the manoeuvering area and the unobstructed approach surfaces described in chapter 3 are available.

d. Rotorwash Considerations. Preliminary data indicates that the rotorwash generated by a tiltrotor or large rotorcraft can affect objects less than 160 feet (49 m) away from the liftoff or touchdown point and protection should be provided for unsecured objects less than 500 feet (150 m) from the liftoff or touchdown point. Additional information on rotorwash can be found in the FAA report “Evaluation of Rotorwash Characteristics for Tiltrotor and Tiltiwing Aircraft in Hovering Flight,” DOT/FAA/RD-90/16.

63. GROUND OPERATIONS. Taxiways and/or hover taxi routes between TLOFs and service facilities or the passenger terminal must be compatible with other airport operations and air traffic control procedures. TLOF sites should be selected to minimize crossings of runways and taxiways used by fixed-wing aircraft.

a. Airport Traffic Control. Air traffic controllers control aircraft and ground vehicle traffic on the movement area of the airport. The airport movement area encompasses the runways, the TLOF, and the taxiway system, including apron edge taxiways. The aircraft operator is responsible for movement of the aircraft from the limit of the taxiway system to the parking or gate positions.

AC 150/5390-3

b. Line of Sight. If the airport has an airport traffic control tower, the TLOFs, runways, taxiways, and/or hover taxi access routes to the terminal/hangar area must be visible to air traffic controllers in the tower.

C. Apron/Ramp Parking Positions. Tiltrotor parking positions should be located on heat resistant pavements and provide clearance from buildings or passenger service equipment in accordance with the object clearance requirements of paragraph 16.

64. FUELING AREAS. A hydrant system or central fueling location in a designated area large enough to accommodate the largest tiltrotor or rotorcraft forecasted to operate at the airport is recommended. Fuel hoses should be long enough to avoid the need for aircraft to taxi close to obstacles. If refueling trucks are used, the tiltrotor and/or rotorcraft facilities should be designed to minimize the need for fuel trucks to operate on the FAT0 or TLOF.

65. PASSENGER TRANSFERS. Tiltrotor operations at airports will generate intra- and interline transfers of passengers and baggage. Tiltrotor and rotorcraft airside access should be designed so that interlining passengers are screened at their origination point and, with their carry-on baggage, will not have to be rescreened on entering the airport terminal’s secured area.

66 to 69. RESERVED

-

S/31/91 AC 150/5390-3

CHAPTER 7. EXAMPLES APPLYING VERTIPORT DESIGN

70. GENERAL. This chapter contains illustrations of scvcral concepts that apply rhc design standards and rccommcndations of this AC to the planning of a vcrtiport or a vcrlistop. It is not intcndcd that these illustrations limil a vcrliport proponent’s ingenuity in designing a facility to meet the rcquircmcnls or limitations of a specific site.

CHAPTER 7. EXAMPLES APPLYING VERTIPORT DESIGN

71. COMMERCIAL SERVICE VERTIPORTS. Figures 7-1, 7-2, and 7-3 illustrate three different concepts of how a large vertiport intended to accommodate commercial passcngcr or cargo scrviccs might appear. Each concept assumes a need for niulliplc gale positions.

72. A “SMALL” VERTIPORT OR VERTISTOP. Figure 7-4 illustrates a concept of a ground level vertiport or vertistop capable of accommodating airline type services. The facility is designed to serve a maximum of one tiltrotor aircraft at a time.

73. AN ELEVATED PRIVATE-USEVERTIPORT. Figure 7-5 illustrates an elevated vertiport inlended for the exclusive use of the owner. The facility dimensions can be proportioned according to the size of the tiltrotor aircraft being used. The limited size of the facility would restrict operations to a visual environment. The indicated weight and size limitations are not necessary since operations are to be conducted only with permission of the owner.

Figure 7-4: picture of page 36Figure 7-4 · page 36
Picture of the page from the copy saved here

In this concept, a commercial service vertiport is located on a large pier structure extending out into the riverflake. Two elongated FATOs and TLOFs cross in a shallow “X”. Approaches are always made toward the shoreline. All departures are made on a heading away from the shoreline.

Figure 7-1. A vertiport on a pier

AC 150;‘5390-3 5131191

In this concept, a facility capable of accommodating 4 tiltrotor aircraft is located on a parking structure spanning a freeway. The dimensions of the structure permit a modestly elongated FAT0 and TLOF to be developed paralleling the long dimensions of the building. Passenger ticketing, parking, etc., is provided for immediately below the flight operations level. Additional parking is available for the general public on lower levels of the building. Passenger access to the aircraft is accomplished via an enclosed disappearing escalator which lowers to be flush with the apron surface when not in use.

Figure 7-2. A vertiport spanning a freeway

Figure 7-1: picture of page 34Figure 7-1 · page 34
Picture of the page from the copy saved here

In this concept, the FAT0 overlies the river allowing the approach surface to be located in the uncluttered airspace over the river. The TLOF is situated on the river bank and has the recommended 75-foot (22.5 m) clearances to adjacent buildings. A paved taxiway leads to a 3 gate terminal located a modest distance in from the river’s edge.

Figure 7-3. A riverfront vertiport

5/31/91 AC 150/5390-3

This concept illustrates a commercial vertistop accommodating minimal activity, i.e., not more than 1 tiltrotor aircraft at a time. Terminal and parking facilities are sized to meet current demands for service. Additional land is provided should there be a need to expand at a later date.

Figure 7-4. A low activity vertistop

Figure 7-3: picture of page 35Figure 7-3 · page 35
Picture of the page from the copy saved here

This concept illustrates a private-use vertiport located on a rooftop intended for the exclusive use of the owner. Therefore, the FAT0 and raised TLOF are sized according to the size of the tiltrotor aircraft using the facility. As a private-use facility, it is permissible to have portions of the FAT0 lie in the clear airspace beyond the buildings edge. The raised TLOF platform is marked with the corporate symbol and shows the facility was designed to accommodate an 8,000 pound aircraft with a 50-foot rotor span.

Figure 7-5. A rooftop private-use vertiport

AC 150/53!20-3 5l31Pl

). .A.,.. ,. ,” . ,.a ....-..a. .A_.,. ..,. ‘ .., ., ,. .-. .a...,

f .1 ~ ‘-’ I ‘.

Figure 7-5: picture of page 36Figure 7-5 · page 36
Picture of the page from the copy saved here

VERTIPORT ON AN AIRPORT TERMINAL 1

VERTIPORT ON AN AIRPORT TERMINAL 1

5/31/91

APPENDIX 1

NOTE: ALL DIMENSIONS ARE APPROXIMATE

* Fan-in-wing F.D. Fan Diameter

l * Tilt-wing

AC 150/5390-3

Appendix 1

EUROTOR CTR-1900

LANDING GEAR NUMBER 1 TREAD WHEELBAsE PASSENGERS FEET I FEET I I

~ 15

I 22 I 31 1

~ 11 30 39

~ 11 30 52

LANDING GEAR NUMBER 1 TREAD WHEELBAsE PASSENGERS FEET I FEET I I

17 28 75

CTR-800

CTR-22A/B

CTR-22C CTR-7500

Tiltrotor aircraft data

ml/91

-

'C

a 0

- 0

I

6-

AC 150/5390-3

Appendix 2

APPENDIX 2

2.7’ 6.3’ J 3.65:, 2.7’ 3.65’ _ 6.3’

*U.S. GOVERNMENT PRINTING OFFICE: 1991--517-000/46037

Vertiport marking