Radar Vectors
Advisory Circular Cancelled Issued Sep 30, 2009 AAS-100 124 pages Copy saved Nov 18, 2026

AC 150/5320-6E Airport Pavement Design and Evaluation

Provides guidance to the public on the design and evaluation of pavements at civil airports. Because of the size of the document, it is available as one large file (see Complete) or as four smaller files (see Parts 1-4). See also related Airport Design Software.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Airport Pavement Design and Evaluation

Date: 9/30/2009 Initiated by: AAS-100

AC No: 150/5320-6E Change:

1. PURPOSE. This advisory circular (AC) provides guidance to the public on the design and evaluation of pavements at civil airports.

2. CANCELLATION. This AC cancels AC 150/5320-6D, Airport Pavement Design and Evaluation, dated July 7, 1995.

3. APPLICATION. The FAA recommends the guidelines and standards in this AC for airport pavement design and evaluation. In general, use of this AC is not mandatory. However, use this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and with revenue from the Passenger Facility Charge (PFC) Program. See Grant Assurance No. 34, “Policies, Standards, and Specifications,” and PFC Assurance No. 9, “Standards and Specifications.

4. RELATED READING MATERIAL. The publications listed in Appendix 4 provide further guidance and detailed information on the design and evaluation of airport pavements.

5. UNITS. Through this AC, customary English units will be used with soft conversion to metric units for tables and figures and hard conversion for the text.

Michael O’Donnell Director of Airport Safety and Standards

ii

This page intentionally blank.

TABLE OF CONTENTS

TABLE OF CONTENTS iii

TABLE OF CONTENTS

LIST OF TABLES vi

LIST OF FIGURES vii

FOREWORD viii

CHAPTER 1. AIRPORT PAVEMENTS— 1

THEIR FUNCTION AND PURPOSES 1

100. GENERAL 1 101. SPECIFICATIONS AND STANDARDS 1 102. SPECIAL CONSIDERATIONS 1 103. STAGED CONSTRUCTION OF AIRPORT PAVEMENTS 2

CHAPTER 2. SOIL INVESTIGATIONS AND EVALUATION 3

200. GENERAL 3 201. SOIL INVESTIGATIONS 3 202. SURVEYING AND SAMPLING 4 203. SOIL TESTS 5 204. UNIFIED SOIL CLASSIFICATION 6 205. SOIL STRENGTH TESTS 9 206. SUBGRADE STABILIZATION 10 207. SEASONAL FROST 10 208. PERMAFROST 11

CHAPTER 3. PAVEMENT DESIGN FOR AIRPLANES WEIGHING 13

MORE THAN 30,000 POUNDS 13

SECTION 1. DESIGN CONSIDERATIONS 13 300. SCOPE 13 301. DESIGN PHILOSOPHY 13 302. REPORTING PAVEMENT STRENGTH 13 303. BACKGROUND 13 304. PAVEMENT DESIGN USING FAARFIELD 14 305. TRAFFIC DISTRIBUTION 20 306. TYPICAL SECTIONS 20 307. FROST AND PERMAFROST DESIGN 21 SECTION 2. FLEXIBLE PAVEMENT DESIGN 24 308. GENERAL 24 309. HOT MIX ASPHALT SURFACING 24 310. BASE COURSE 24 311. SUBBASE 24 312. SUBGRADE 25 313. SWELLING SOILS 27 314. SELECTION OF DESIGN CBR VALUE 27 315. FLEXIBLE PAVEMENT DESIGN 28 316. DESIGN EXAMPLE 30 317. STABILIZED BASE AND SUBBASE 32 318. FULL-DEPTH ASPHALT PAVEMENTS 32 319. FROST EFFECTS 32

iii

AC 150/5320-6E 9/30/2009 SECTION 3. RIGID PAVEMENT DESIGN 33 320. GENERAL 33 321. CONCRETE PAVEMENT 33 322. SUBBASE 33 323. SUBBASE QUALITY 33 324. STABILIZED SUBBASE. 33 325. SUBGRADE 34 326. DETERMINATION OF MODULUS (E VALUE) FOR RIGID PAVEMENT SUBGRADE 34 327. DETERMINATION OF CONCRETE SLAB THICKNESS 34 328. USE OF FAARFIELD FOR NEW RIGID PAVEMENT DESIGN 35 329. CRITICAL AND NONCRITICAL AREAS 36 330. DESIGN EXAMPLE 36 331. FROST EFFECTS 36 332. JOINTING OF CONCRETE PAVEMENTS 38 333. SPECIAL JOINTING CONSIDERATIONS FOR POSSIBLE FUTURE EXPANSION 42 334. JOINTING STEEL 43 335. JOINT SEALANTS AND FILLERS 44 336. JOINT LAYOUT 44 337. CONCRETE PAVEMENT CONTAINING EMBEDDED STEEL FOR CRACK CONTROL 44 338. TYPE AND SPACING OF EMBEDDED STEEL BARS 44 339. AMOUNT OF EMBEDDED STEEL. 46 340. DIMENSIONS AND WEIGHTS OF EMBEDDED STEEL 46 341. WELDED WIRE FABRIC 47 342. JOINTING OF EMBEDDED STEEL CONCRETE PAVEMENTS 48 343. CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 48 344. CRCP JOINTING 51 345. CRCP TERMINAL TREATMENT 51 346. CRCP DESIGN EXAMPLE 54 347. PRESTRESSED CONCRETE PAVEMENT 55

CHAPTER 4. AIRPORT PAVEMENT OVERLAYS AND RECONSTRUCTION 57

400. GENERAL 57 401. CONDITION OF EXISTING PAVEMENT 57 402. MATERIAL SELECTION CONSIDERATIONS 57 403. OVERLAY DESIGN 57 404. OVERLAYS OF EXISTING FLEXIBLE PAVEMENTS 59 405. OVERLAYS OF EXISTING RIGID PAVEMENTS 61 406. THICKNESS DESIGN FOR RUBBLIZED CONCRETE PAVEMENTS 68 407. PREPARATION OF THE EXISTING SURFACE FOR THE OVERLAY 69 408. MATERIALS AND METHODS 70 409. NEW OVERLAY MATERIALS 70

CHAPTER 5. PAVEMENT DESIGN FOR AIRPLANES WEIGHING LESS THAN 30,000 POUNDS 71

500. GENERAL 71 501. REPORTING PAVEMENT STRENGTH 71 502. TYPICAL SECTIONS 71 503. FLEXIBLE PAVEMENT MATERIALS 71 504. FLEXIBLE PAVEMENT DESIGN 72 505. RIGID PAVEMENT MATERIALS 75 506. RIGID PAVEMENT THICKNESS 76 507. AGGREGATE TURF 81 508. OVERLAYS 81 509. HELIPORT/VERTIPORT DESIGN 82

iv

CHAPTER 6. PAVEMENT EVALUATION 83

600. PURPOSES OF PAVEMENT EVALUATION 83 601. EVALUATION PROCESS 83 602. FLEXIBLE PAVEMENTS 84 603. APPLICATION OF FLEXIBLE PAVEMENT EVALUATION PROCEDURES 84 604. RIGID PAVEMENTS 86 605. APPLICATION OF RIGID PAVEMENT EVALUATION PROCEDURES 87 606. USE OF RESULTS 88 607. REPORTING PAVEMENT STRENGTH 88

CHAPTER 7. PAVEMENT DESIGN FOR AIRFIELD SHOULDERS 89

700. PURPOSE 89 701. APPLICATION 89 702. BACKGROUND 89 703. PURPOSE OF DESIGN PROCEDURE 89 704. REPORTING PAVED SHOULDER DESIGN 89 705. DESIGN PROCEDURE 89 706. PAVEMENT LAYER THICKNESS AND MATERIAL REQUIREMENTS 90 707. EMERGENCY AND MAINTENANCE VEHICLE CONSIDERATIONS 90 708. AREAS SUSCEPTIBLE TO FROST HEAVE 90

APPENDIX 1. ECONOMIC ANALYSIS 91

APPENDIX 2. ORDER 5300.7 95

APPENDIX 3. DESIGN OF STRUCTURES FOR HEAVY AIRPLANES 105

APPENDIX 4. RELATED READING MATERIAL 107

APPENDIX 5. AIRFIELD PAVEMENT DESIGN SOFTWARE 110

APPENDIX 6. FAARFIELD INTERNAL AIRPLANE LIBRARY 111

v

LIST OF TABLES

LIST OF TABLES

TABLE 2-1. TYPICAL SUBSURFACE BORING SPACING AND DEPTH FOR NEW CONSTRUCTION 4 TABLE 2-2. SOIL CHARACTERISTICS PERTINENT TO PAVEMENT FOUNDATIONS 8 TABLE 2-3. SOIL FROST GROUPS 11 TABLE 3-1. STANDARD NAMING CONVENTION FOR COMMON AIRPLANE GEAR

CONFIGURATIONS 15 TABLE 3-1. STANDARD NAMING CONVENTION FOR COMMON AIRPLANE GEAR

CONFIGURATIONS (CONTINUED) 16 TABLE 3-2. PAVEMENT REMAINING LIFE BASED ON CDF VALUE 18 TABLE 3-3. REDUCED SUBGRADE STRENGTH RATINGS 21 TABLE 3-4. SUBGRADE COMPACTION REQUIREMENTS FOR FLEXIBLE PAVEMENTS 26 TABLE 3-5. DENSITIES FOR SUBGRADE IN EXAMPLE 26 TABLE 3-6. COMPACTION REQUIREMENTS FOR EXAMPLE 27 TABLE 3-7. RECOMMENDED TREATMENT OF SWELLING SOILS 27 TABLE 3-8. LAYER TYPES IN FAARFIELD 28 TABLE 3-9. MINIMUM AGGREGATE BASE COURSE THICKNESS 30 TABLE 3-10. AIRPLANE TRAFFIC MIX EXAMPLE 31 TABLE 3-11. PAVEMENT STRUCTURE INFORMATION FOR DESIGN EXAMPLE 31 TABLE 3-12. ADDITIONAL AIRPLANE INFORMATION FOR DESIGN EXAMPLE 32 TABLE 3-13. AIRPLANE MIXTURE INPUT DATA 36 TABLE 3-14. PAVEMENT LAYER INPUT DATA 36 TABLE 3-15. PAVEMENT JOINT TYPES 41 TABLE 3-16. RECOMMENDED MAXIMUM JOINT SPACINGS - RIGID PAVEMENT WITH OR WITHOUT

STABILIZED SUBBASE 41 TABLE 3-17. DIMENSIONS AND SPACING OF STEEL DOWELS 44 TABLE 3-18. YIELD STRENGTHS OF VARIOUS GRADES OF REINFORCING STEEL 46 TABLE 3-19. DIMENSIONS AND UNIT WEIGHTS OF DEFORMED STEEL REINFORCING BARS

NOMINAL DIMENSIONS 47 TABLE 3-20. SECTIONAL AREAS OF WELDED FABRIC 47 TABLE 3-21. AIRPLANE MIX DATA FOR CRCP DESIGN EXAMPLE 54 TABLE 4-1. RIGID PAVEMENT DISTRESS TYPES USED TO CALCULATE THE STRUCTURAL

CONDITION INDEX, SCI 61 TABLE 5-1. SUBGRADE COMPACTION REQUIREMENTS FOR LIGHT LOAD FLEXIBLE PAVEMENTS 72

vi

LIST OF FIGURES

LIST OF FIGURES

FIGURE 2-1. TYPICAL BORING LOG 7 FIGURE 2-2. RELATIONSHIP BETWEEN AIR THAWING INDEX AND THAW PENETRATION INTO

GRANULAR, NON-FROST SUSCEPTABLE SUBGRADE SOIL 12 FIGURE 3-1. TWO EFFECTIVE TIRE WIDTHS - NO OVERLAP 19 FIGURE 3-2. ONE EFFECTIVE TIRE WIDTH – OVERLAP 19 FIGURE 3-3. EXAMPLE OF CDF CONTRIBUTION FOR AIRPLANE MIX 20 FIGURE 3-4. TYPICAL PLAN AND CROSS SECTION FOR RUNWAY PAVEMENT 23 FIGURE 3-5. FAARFIELD SCREENSHOT SHOWING FINAL PAVEMENT THICKNESS DESIGN 31 FIGURE 3-6. STRUCTURE WINDOW IN FAARFIELD 37 FIGURE 3-7. AIRPLANE WINDOW IN FAARFIELD 37 FIGURE 3-8. RIGID PAVEMENT JOINT TYPES AND DETAILS 39 FIGURE 3-9. RIGID PAVEMENT JOINT TYPE DETAILS 40 FIGURE 3-10. TYPICAL JOINT LAYOUT PATTERN FOR RUNWAY, PARALLEL TAXIWAY, AND

CONNECTOR 45 FIGURE 3-11. JOINTING IN RIGID PAVEMENT WITH EMBEDDED STEEL 50 FIGURE 3-12. CONTINUOUSLY REINFORCED CONCRETE PAVEMENT – JOINT DETAILS 51 FIGURE 3-13. CONTINUOUSLY REINFORCED CONCRETE PAVEMENT – JOINT DETAILS 52 FIGURE 3-14. CONTINUOUSLY REINFORCED CONCRETE PAVEMENT – WIDE FLANGE BEAM

TERMINAL JOINT 53 FIGURE 3-15. COMPUTED SLAB THICKNESS, CRCP EXAMPLE 54 FIGURE 4-1. TYPICAL OVERLAY PAVEMENTS 58 FIGURE 4-2. DESIGN EXAMPLE OF FLEXIBLE OVERLAY ON EXISTING FLEXIBLE PAVEMENT 59 FIGURE 4-3. DESIGN EXAMPLE OF RIGID OVERLAY ON EXISTING FLEXIBLE PAVEMENT 61 FIGURE 4-4. CDFU COMPUTATION USING FAARFIELD 63 FIGURE 4-5. DESIGN EXAMPLE OF FLEXIBLE OVERLAY ON EXISTING RIGID PAVEMENT WITH SCI

70 64 FIGURE 4-6. DESIGN EXAMPLE OF FLEXIBLE OVERLAY ON EXISTING RIGID PAVEMENT WITH SCI

100 65 FIGURE 4-7. DESIGN EXAMPLE OF RIGID OVERLAY ON EXISTING FULLY UNBONDED RIGID

PAVEMENT 67 FIGURE 5-1. TYPICAL SECTIONS FOR PAVEMENTS SERVING LIGHT AIRPLANES 73 FIGURE 5-2. FAARFIELD AIRPLANE WINDOW – LIGHT LOAD PAVEMENT DESIGN 74 FIGURE 5-3. CALCULATION OF SUBBASE LAYER THICKNESS 75 FIGURE 5-4. JOINTING TYPES FOR LIGHT-LOAD RIGID PAVEMENT 77 FIGURE 5-5. JOINTING DETAILS FOR LIGHT-LOAD RIGID PAVEMENT 78 FIGURE 5-6. JOINTING LAYOUT PATTERNS FOR LIGHT-LOAD RIGID PAVEMENT – 60 FEET WIDE 79 FIGURE 5-7. JOINTING LAYOUT PATTERNS FOR LIGHT-LOAD RIGID PAVEMENT – 50 FEET WIDE 80 FIGURE 5-8. DESIGN EXAMPLE FOR AGGREGATE TURF PAVEMENT. 81 FIGURE 6-1. EXAMPLE OF A FLEXIBLE PAVEMENT STRUCTURE FOR EVALUATION 85 FIGURE 6-2. EXAMPLE OF A RIGID PAVEMENT STRUCTURE FOR EVALUATION 87

vii

FOREWORD

viii

FOREWORD

This AC provides guidance on the structural design and evaluation of airport pavements.

Although airplane landing gears play a role in airport pavement design and evaluation, this AC does not dictate any facet of landing gear design. In 1958, the FAA adopted a policy of limiting maximum Federal participation in airport pavements to a pavement section designed to serve a 350,000-pound (158 757 kg) airplane with a DC-8-50 series landing gear configuration. The intent of the policy was to ensure that future airplanes were equipped with landing gears that would not stress pavements more than the referenced 350,000-pound (158 757 kg) airplane.

Throughout the 20th century, airplane manufacturers accepted and followed the 1958 policy and designed airplane landing gears that conformed to it—even though airplane gross weights have long exceeded 350,000 pounds (158 757 kg). Despite increases in airplane weights, manufacturers were able to conform to the policy by increasing the number and spacing of landing gear wheels. Unfortunately, adding extra wheels and landing gears does not contribute to efficiency, and airplane manufacturers are focusing on designing airplane gear configurations to optimize the efficiency of the airplanes. With this change in philosophy and increasing airplane weights, airfield pavements must be designed to withstand increased loading conditions.

Historical pavement design guidance presented in previous versions of this AC was based on methods of analysis that resulted from empirical research and field performance. Although it may have been possible to adjust these methods to address new gear configurations and increased pavement loading, newer design procedures, such as the layered elastic and finite element procedures discussed in Chapter 3, were better adapted for this challenge

The pavement design guidance presented in this AC implements layered elastic theory for flexible pavement design and three-dimensional finite element theory for rigid pavement design. The FAA adopted these methodologies to address the impact of new landing gear configurations and increased pavement load conditions. These procedures are robust and can address future gear configurations without modifying their underlying design procedures.

Chapter 6 presents the pavement evaluation portion of this AC. An airplane operator could be penalized unfairly if an existing facility was evaluated using a method different from that employed in the original design. A slight change in pavement thickness can have a dramatic effect on the payload or range of an airplane. Since a new pavement design methodology might produce different pavement thicknesses, an evaluation of an existing pavement using the new methodology could result in incompatible results. To avoid this situation, airport operators should base the evaluation, whenever possible, on the same methodology as was used for the design.

Where new airplanes are added to the traffic mix at an existing facility, it may not be possible to evaluate the pavement with the original design procedure. For example, when adding a new airplane with a unique gear configuration to the traffic mixture at a facility, it may be impossible to assess the impact of the new airplane using the original design procedures. In these instances, it is necessary to evaluate the pavement with a design procedure capable of addressing the new traffic mixture.

CHAPTER 1. AIRPORT PAVEMENTS—

THEIR FUNCTION AND PURPOSES

100. GENERAL. Airport pavements are constructed to provide adequate support for the loads imposed by airplanes and to produce a firm, stable, smooth, all-year, all-weather surface free of debris or other particles that may be blown or picked up by propeller wash or jet blast. In order to satisfactorily fulfill these requirements, the pavement must be of such quality and thickness that it will not fail under the load imposed. In addition, it must possess sufficient inherent stability to withstand, without damage, the abrasive action of traffic, adverse weather conditions, and other deteriorating influences. To produce such pavements requires a coordination of many factors of design, construction, and inspection to assure the best possible combination of available materials and a high standard of workmanship.

a. Types of Pavement. Pavements discussed in this circular are flexible, rigid, hot mix asphalt overlays, and rigid overlays. Various combinations of pavement types and stabilized layers result in complex pavements classified between flexible and rigid. The design and evaluation guidance in this circular can be adapted to any pavement type.

b. Economic Analysis and Design Selection. With proper design and construction, any pavement type (rigid, flexible, composite, etc.) can provide a satisfactory pavement for any civil airplane. However, some designs may be more economical than others and can still provide satisfactory performance. The engineer is required to provide a rationale for the selected design in the engineer’s report (see AC 150/5300-9, Predesign, Prebid, and Preconstruction Conferences for Airport Grant Projects). Engineers often base this rationale on economic factors derived from evaluating several design alternatives. Use life-cycle cost analysis if the design selection is based on least cost. Appendix 1 demonstrates an example of a life-cycle cost analysis of alternatives for pavement rehabilitation. Research report FAA-RD-81/078, Economic Analysis of Airport Pavement Rehabilitation Alternatives – An Engineering Manual, provides more details on life-cycle cost analysis. Many new developments in construction have evolved, such as recycling, that can significantly affect pavement costs. Alternate construction bids are appropriate in instances where no clear cost advantage is established in the design process. Economic factors do not always control the design selection. Operational constraints, funding limitations, future expansion, and other issues can override economic factors in the design selection. The engineer’s report should address these considerations.

c. Pavement Courses.

(1) Surface. Surface courses include Portland cement concrete (PCC), hot mix asphalt (HMA), sand-bituminous mixture, and sprayed bituminous surface treatments.

(2) Base. Base courses consist of a variety of different materials, which generally fall into two main classes, treated and untreated. An untreated base consists of crushed or uncrushed aggregates. A treated base normally consists of a crushed or uncrushed aggregate mixed with a stabilizer such as cement, bitumen, etc.

(3) Subbase. Subbase courses consist of a granular material, a stabilized granular material, or a stabilized soil.

(4) Geosynthetics. The term geosynthetics describes a range of manufactured synthetic products used to address geotechnical problems. The term is generally understood to encompass four main products: geotextiles, geonets/geogrids, geomembranes and geocomposites. The synthetic nature of the materials in these products makes them suitable for use in the ground where high levels of durability are required. These products have a wide range of applications, including use as a separation between subbase aggregate layers and the underlying subgrade. The need for geosynthetics within a pavement section is dependent upon subgrade soil conditions, groundwater conditions, and the type of overlying pavement aggregate.

101. SPECIFICATIONS AND STANDARDS.

a. Specifications. Reference is made by Item Number throughout the text to construction material specifications contained in AC 150/5370-10, Standards for Specifying Construction of Airports.

b. Geometric Standards. AC 150/5300-13, Airport Design, presents geometric standards for pavement lengths, widths, grades, and slopes.

102. SPECIAL CONSIDERATIONS. Airport pavements should provide a skid resistant surface that will provide good traction during any weather conditions. AC 150/5320-12, Measurement, Construction, and Maintenance of Skid Resistant Airport Pavement Surfaces, presents information on skid resistant surfaces.

103. STAGED CONSTRUCTION OF AIRPORT PAVEMENTS. In some instances, it may be necessary to construct the airport pavement in stages; that is, to build up the pavement profile, layer by layer, as the traffic using the facility increases in weight and number. Lateral staging, i.e., planning for future widening of pavements, is sometimes advantageous to accommodate larger airplanes. If stage construction is to be undertaken, the need for sound planning cannot be overemphasized. It is important to design the complete pavement prior to the start of any stage and to assure that each stage provides an operational surface. The planning of a stage-constructed pavement should recognize a number of considerations.

a. Adequacy of Each Stage. Design each stage to adequately accommodate the traffic that will use the pavement until the next stage is constructed.

b. Drainage. Design and construct the underlying layers and drainage facilities of a pavement constructed in stages to the standards required for the final cross-section. Providing the proper foundation and drainage facilities in the first stage is mandatory, as the underlying layers will not be readily accessible for upgrading in the future.

CHAPTER 2. SOIL INVESTIGATIONS AND

EVALUATION

200. GENERAL. The importance of accurate identification and evaluation of pavement foundations cannot be overemphasized. Although it is impossible to explore the entire field of soil mechanics in a publication such as this, the following text will highlight those aspects that are particularly important to the airport paving engineer.

a. Classification System. Use the Unified Soil Classification (USC) system in engineering matters concerning civil airport pavements. To avoid misunderstanding, certain terms employed are defined below:

(1) SOIL Definition. For engineering purposes, and particularly as it applies to airports, soil includes all natural deposits that can be moved with earth moving equipment, without requiring blasting under unfrozen conditions. Harder materials are considered to be rock.

(2) Conditions and Properties. Soil conditions include such items as the elevation of the water table, the presence of water bearing strata, and the field properties of the soil. Field properties of the soil include the density, moisture content, and frost penetration.

(3) Profile. The soil profile is the vertical arrangement soil layers, each of which possesses different physical properties from the adjacent layer.

(4) Subgrade. Subgrade soil is the soil that forms the foundation for the pavement. It is the soil directly beneath the pavement structure.

b. Subgrade Support. It should be remembered that the subgrade soil ultimately provides support for the pavement and the imposed loads. The pavement serves to distribute the imposed load to the subgrade over an area greater than that of the tire contact area. The greater the thickness of pavement, the greater is the area over which the load on the subgrade is distributed. It follows, therefore, that the more unstable the subgrade soil, the greater is the required area of load distribution and consequently the required thickness of pavement is greater. The soils having the best engineering characteristics encountered in the grading and excavating operations should be incorporated in the upper layers of the subgrade by selective grading.

c. Drainage. In addition to the relationship that soil conditions bear to grading and paving operations, they determine the necessity for underdrains and materially influence the amount of surface runoff. Thus, they have a resulting effect on the size and extent of other drainage structures and facilities. (See AC 150/5320-5, Surface Drainage Design.)

201. SOIL INVESTIGATIONS.

a. Distribution and Properties. To provide essential information on the various types of soils, investigations should be made to determine their distribution and physical properties. This information combined with data on site topography and area climatic records, provides basic planning material essential to the logical and effective development of the airport. An investigation of soil conditions at an airport site will include—

(1) Subsurface Soil Profile. An investigation of subsurface soil properties to determine the arrangement of different layers of the soil with relation to the proposed subgrade elevation.

(2) Sampling. Collection of representative samples of the layers of soil.

(3) Testing. Testing of samples to determine the physical properties of the various soil materials with respect to in-place density and subgrade support.

(4) Availability. A review to determine the availability of materials for use in construction of the subgrade and pavement.

b. Procedures. With respect to sampling and surveying procedures and techniques, American Society for Testing and Materials (ASTM) D 420, Standard Guide to Site Characterization for Engineering Design and Construction Purposes, is most frequently used. This method is based entirely on the soil profile. In the field, ASTM D 2488, Standard Practice for Description and Identification of Soils (Visual-Manual Procedures), is commonly used to identify soils by such characteristics as color, texture, structure, consistency, compactness, cementation, and, to varying degrees, chemical composition.

(1) Maps. Department of Agriculture soils maps, United States Geodetic Survey (USGS) geologic maps, and USGS engineering geology maps can prove valuable aids in the study of soils at and in the vicinity of the airport. Although the pedological classification, determined from these maps, does not treat soil as an engineering or construction material, data so obtained are extremely useful to the agronomist in connection with the development of turf areas on airports and to the engineer concerned with preliminary investigations of site selection, development costs, and alignment.

(2) Aerial Photography. The practice of determining data on soils with aerial photographs is established and commonly acceptable. Relief, drainage, and soil patterns may be determined from the photographs, and an experienced photo interpreter can define differences in characteristics of soils. By employing this method of investigation, it is possible to expedite soil studies and reduce the amount of effort required to gather data.

202. SURVEYING AND SAMPLING.

a. Subsurface Borings. The initial step in an investigation of subsurface conditions is a soil survey to determine the quantity and extent of the different types of soil, the arrangement of soil layers, and the depth of any subsurface water. These profile borings are usually obtained with a soil auger or similar device. Washed borings are not recommended due to inaccuracies of depth determinations. The intent of the borings is to determine the soil or rock profile and its lateral extent. Inasmuch as each location presents its particular problems and variations, the spacing of borings cannot always be definitely specified by rule or preconceived plan. Suggested criteria for the location, depth, and number of borings for new construction are given in table 2-1. Wide variations in these criteria can be expected due to local conditions.

Nondestructive testing (NDT), as described in AC 150/5370-11, Use of Nondestructive Testing Devices in the Evaluation of Airport Pavement, can be used for computing subgrade strength and to locate soil borings and sampling locations for evaluation of existing pavements. Also, boring logs from original construction and prior evaluations can be used.

TABLE 2-1. TYPICAL SUBSURFACE BORING SPACING AND DEPTH FOR NEW CONSTRUCTION

AREA SPACING DEPTH

Runways and Taxiways Random Across Pavement at 200foot (60 m) Intervals

Cut Areas - 10' (3 m) Below Finished Grade Fill Areas - 10' (3 m) Below Existing Ground1 Other Areas of Pavement 1 Boring per 10,000 Square Feet (930 sq m) of Area

Cut Areas - 10' (3 m) Below Finished Grade Fill Areas - 10' (3 m) Below Existing Ground1 Borrow Areas Sufficient Tests to Clearly Define the Borrow Material

To Depth of Borrow Excavation

1For deep fills, boring depths must be sufficient to determine the extent of consolidation and/or slippage the fill may cause.

b. Number of Borings, Locations, and Depths. Obviously, the locations, depths, and numbers of borings must be such that all important soil variations can be determined and mapped. Whenever past experience at the location in question has indicated that settlement or stability in deep fill areas may be a problem or, if in the opinion of the engineer, additional investigations are warranted, more or deeper borings may be required in order to determine the proper design, location, and construction procedures. Conversely, where uniform soil conditions are encountered, fewer borings may be acceptable.

c. Boring Log. A graphic log of soil conditions can be of great value in assessing subgrade conditions. It is recommended that the graphic log be developed, which summarizes the results of the soil explorations. A typical graphic log is included as figure 2-1. The graphic log should include—

(1) Location

(2) Date performed

(3) Type of exploration

(4) Surface elevation

(5) Depth of materials

(6) Sample identification numbers

(7) Classification

(8) Water table

(9) Standard penetration test (SPT)

d. Soil Survey Areas. The soil survey is not confined to soils encountered in grading or necessarily to the area within the boundaries of the airport site. Possible sources of locally available material that may be used as borrow areas or aggregate sources should be investigated.

e. Undisturbed Samples. Samples representative of the different layers of the various soils encountered and various construction materials discovered should be obtained and tested in the laboratory to determine their physical and engineering properties. In-situ properties such as in-place density, shear strength, consolidation characteristics, etc. may necessitate obtaining “undisturbed” core samples. ASTM D 1587, Standard Practice for Thin-Walled Tube Sampling of Soils for Geotechnical Purposes, describes a method of obtaining “undisturbed” soil samples. Because the results of a test can only be as good as the sampling, it is of utmost importance that each sample be representative of a particular type of soil material and not be a careless and indiscriminate mixture of several materials.

f. Inplace Testing. Pits, open cuts, or both may be required for making in-place bearing tests, taking undisturbed samples, charting variable soil strata, etc. This type of supplemental soil investigation is recommended for situations that warrant a high degree of accuracy or when in-situ conditions are complex and require extensive investigation.

203. SOIL TESTS.

a. Physical Soil Properties. To determine the physical properties of a soil and to provide an estimate of its behavior under various conditions, it is necessary to conduct certain soil tests. A number of field and laboratory tests have been developed and standardized. Detailed methods of performing soil tests are completely covered in publications of the ASTM.

b. Testing Requirements. Soil tests are usually identified by terms indicating the soil characteristics that the tests will reveal. Terms that identify the tests considered to be the minimum or basic requirement for airport pavement, with their ASTM designations and brief explanations, follow:

(1) Standard Practice for Dry Preparation of Soil Samples for Particle-Size Analysis and Determination of Soil Constants (ASTM D 421). The dry method should be used only for clean, cohesion-less granular materials.

(2) Standard Test Method for Particle-Size Analysis of Soils (ASTM D 422). This analysis provides a quantitative determination of the distribution of particle sizes in soils.

(3) Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils (ASTM D 4318). The plastic and liquid limits of soil define in a standard manner the lowest moisture content at which a soil will change from a semisolid to a plastic state and at which a solid passes from a plastic to a liquid state, respectively. The plasticity index is the numerical difference between the plastic limit and the liquid limit. It indicates the range in moisture content over which a soil remains in a plastic state prior to changing into a liquid. The plastic limit, liquid limit, and plasticity index of soils are used in engineering classification in accordance with the Unified Soil Classification System (ASTM D 2487). In conjunction with particle size analysis, natural moisture content, and other soil properties or conditions, the limits may be used to estimate engineering properties or behavior of soils such as shrink/swell potential, consolidation characteristics, construction/stabilization characteristics, permeability, and strength characteristics.

(4) Moisture-Density Relations of Soils . For purposes of compaction control during construction, tests to determine the moisture-density relations of the different types of soils should be performed.

(i) Heavy Load Pavements. For pavements designed to serve airplanes weighing 60,000 pounds (27 216 kg) or more, use ASTM Method D 1557, Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3)).

(ii) Light Load Pavements. For pavements designed to serve airplanes weighing less than 60,000 pounds (27 216 kg), use ASTM Method D 698, Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ftlbf/ft3 (600 kN-m/m3)).

(5) Standard Test Method for CBR (California Bearing Ratio) of Laboratory-Compacted Soils (ASTM D 1883). This test is used to assign a CBR (California Bearing Ratio) value to subgrade soils for use in the design of flexible pavements.

(6) Modulus of Soil Reaction (AASHTO T 222). This test is used to determine the modulus of soil reaction, k, for use in the design of rigid pavements.

c. Supplemental Tests. In many cases, additional soil tests will be required over those listed in paragraph 203b above. It is not possible to cover all the additional tests that may be required; however, a few examples are presented below. This list should not be considered all-inclusive.

(1) Test Method for Shrinkage Factors of Soils by the Mercury Method (ASTM D 427). This test may be required in areas where swelling soils might be encountered.

(2) Standard Test Method for Permeability of Granular Soils (Constant Head) (ASTM D 2434). This test may be needed to assist in the design of subsurface drainage.

(3) Determination of Organic Material in Soils by Wet Combustion (AASHTO T-194). This test may be needed in areas where deep pockets of organic material are encountered or suspected.

(4) Standard Test Method for CBR (California Bearing Ratio) of Soils in Place (ASTM D4429-04). Field bearing tests can be performed when the on site conditions satisfy density and moisture conditions that will exist under the pavement being designed. The method is also described in Manual Series No. 10, Soils Manual (The Asphalt Institute).

204. UNIFIED SOIL CLASSIFICATION. The standard method of classifying soils for engineering purposes is ASTM D 2487, commonly called the Unified System. Table 2-2 provides general soil characteristics pertinent to pavements.

FIGURE 2-1. TYPICAL BORING LOG

TABLE 2-2. SOIL CHARACTERISTICS PERTINENT TO PAVEMENT FOUNDATIONS

205. SOIL STRENGTH TESTS. Soil classification for engineering purposes provides an indication of the probable behavior of the soil as a pavement subgrade. This indication of behavior is, however, approximate. Performance different from that expected can occur due to a variety of reasons such as degree of compaction, degree of saturation, height of overburden, etc. The possibility of incorrectly predicting subgrade behavior can be largely eliminated by measuring soil strength. The strength of materials intended for use in flexible pavement structures is measured by the CBR tests. Materials intended for use in rigid pavement structures are tested by the plate bearing method. Each of these tests is discussed in greater detail below. Resilient modulus is used for rigid pavement design because of the variable stress states. Elastic modulus is estimated from CBR and k using the correlations E = 1500  CBR and E = 26  k1.284

a. California Bearing Ratio. The CBR test is basically a penetration test conducted at a uniform rate of strain. The force required to produce a given penetration in the material under test is compared to the force required to produce the same penetration in a standard crushed limestone. The result is expressed as a ratio of the two forces. Thus a material with a CBR value of 15 means the material in question offers 15 percent of the resistance to penetration that the standard crushed stone offers. Laboratory CBR tests should be performed in accordance with ASTM D 1883, Bearing Ratio of Laboratory-Compacted Soils. Field CBR tests should be conducted in accordance with the ASTM D 4429, Standard Test Method for Bearing Ratio of Soils in Place.

(1) Laboratory. Laboratory CBR tests are conducted on materials that have been obtained from the site and remolded to the density that will be obtained during construction. Specimens are soaked for 4 days to allow the material to reach saturation. A saturated CBR test is used to simulate the conditions likely to occur in a pavement that has been in service for some time. Pavement foundations tend to reach nearly complete saturation after about 3 years. Seasonal moisture changes also dictate the use of a saturated CBR design value since traffic must be supported during periods of high moisture such as spring seasons.

(2) Field. Field CBR tests can provide valuable information on foundations that have been in place for several years. The materials should have been in place for a sufficient time to allow for the moisture to reach an equilibrium condition. An example of this condition is a fill that has been constructed and surcharged for a long period of time prior to pavement construction.

(3) Gravelly Materials. CBR tests on gravelly materials are difficult to interpret. Laboratory CBR tests on gravel often yield CBR results that are too high due to the confining effects of the mold. The assignment of CBR values to gravelly subgrade materials may be based on judgment and experience. The FAA pavement design procedure recommends a maximum subgrade E value of 50,000 psi (345 MPa) (CBR=33.3) for use in design.

(4) Number of Tests. The number of CBR tests needed to properly establish a design value cannot be simply stated. Variability of the soil conditions encountered at the site will have the greatest influence on the number of tests needed. As an approximate “rule of thumb”, three CBR tests on each different major soil type should be considered. The preliminary soil survey will reveal how many different soil types will be encountered. The design CBR value should be conservatively selected. Common paving engineering practice is to select a value that is one standard deviation below the mean. As a rule, a design CBR value of 3 is the lowest practical value that should be assigned. In instances where the subgrade strength is lower than CBR equals 3, the subgrade should be improved through stabilization or other means to raise the design CBR value. The following formula can be used to convert CBR to k value for the subgrade. However, this is only an approximate relationship and it is the recommended appropriate testing to establish design values.

7788 .0

26 CBR 1500 

 

   k , (k in pci)

(5) Lime Rock Bearing Ratio. Some areas of the country use the lime rock bearing ratio (LBR) to express soil strength. To convert LBR to CBR, multiply LBR by 0.8.

b. Plate Bearing Test. As the name indicates, the plate bearing test measures the bearing capacity of the pavement foundation. The result, k value, can be envisioned as the pressure required to produce a unit deflection of the pavement foundation. The plate bearing test result, k value, has the units of pounds per cubic inch (Mega-Newton per cubic meter). Plate bearing tests should be performed in accordance with the procedures contained in AASHTO T 222.

(1) Test Conditions. Plate bearing tests must be conducted in the field and are best performed on test sections that are constructed to the design compaction and moisture conditions. A correction to the k value for saturation is required to simulate the moisture conditions likely to be encountered by the in-service pavement.

(2) Number of Tests. Plate bearing tests are relatively expensive to perform and thus the number of tests that can be conducted to establish a design value is limited. Generally only two or three tests can be performed for each pavement feature. The design k value should be conservatively selected.

(3) Plate Size. The rigid pavement design presented in this circular is based on the elastic modulus (E) or k value. The k value can be determined by a static plate load test using a 30-inch (762 mm) diameter plate. Use of a plate of smaller diameter will result in a higher k value than is represented in the design and evaluation curves.

c. Additional Soil Strength Tests. Where stability of the underlying section is questionable, additional soil strength tests may be necessary. Direct shear tests (ASTM D 3080) or field vane tests (ASTM D 2573) may be required to adequately design the pavement structure.

206. SUBGRADE STABILIZATION. Subgrade stabilization should be considered if one or more of the following conditions exist: poor drainage, adverse surface drainage, frost, or need for a stable working platform. Subgrade stabilization can be accomplished through the addition of chemical agents or by mechanical methods.

a. Chemical Stabilization. Different soil types require different stabilizing agents for best results. The following publications are recommended to determine the appropriate type and amount of chemical stabilization for subgrade soils: Unified Facilities Criteria (UFC) Manual Pavement Design for Airfields, UFC 3-260-02; Soil Cement Construction Handbook, Portland Cement Association; and The Asphalt Institute Manual Series MS-19, Basic Asphalt Emulsion Manual (see Appendix 4).

b. Mechanical Stabilization. In some instances, subgrades cannot be adequately stabilized through the use of chemical additives. The underlying soils may be so soft that stabilized materials cannot be mixed and compacted over the underlying soils without failing the soft soils. Extremely soft soils may require bridging in order to construct the pavement section. Bridging can be accomplished with the use of thick layers of shot rock or cobbles. Thick layers of lean, porous concrete have also been used to bridge extremely soft soils. Geosynthetics should be considered as mechanical stabilization over soft, fine-grained soils. Geosynthetics can facilitate site access over soft soils and aid in reducing subgrade soil disturbance due to construction traffic. Geosynthetics will also function as a separation material to limit long-term weakening of pavement aggregate associated with contamination of the aggregate with underlying fine-grained soils. FHWA-HI-95-038, Geosynthetic Design and Construction Guidelines, provides more information about construction over soft soils using geosynthetics (see Appendix 4).

207. SEASONAL FROST. The design of pavements in areas subject to seasonal frost action requires special consideration. The detrimental effects of frost action may be manifested by non-uniform heave and in loss of soil strength during frost melting. Other related detrimental effects include possible loss of compaction, development of pavement roughness, restriction of drainage, and cracking and deterioration of the pavement surface. Detrimental frost action requires that three conditions be met simultaneously: first, the soil must be frost susceptible; second, freezing temperatures must penetrate into the frost susceptible soil; third, free moisture must be available in sufficient quantities to form ice lenses.

a. Frost Susceptibility. The frost susceptibility of soils is dependent to a large extent on the size and distribution of voids in the soil mass. Voids must be of a certain critical size for the development of ice lenses. Empirical relationships have been developed correlating the degree of frost susceptibility with the soil classification and the amount of material finer than 0.02 mm by weight. Soils are categorized into four groups for frost design purposes: Frost Group 1 (FG-l), FG-2, FG-3, and FG-4. The higher the frost group number, the more susceptible the soil, i.e., soils in FG-4 are more frost susceptible than soils in frost groups 1, 2, or 3. Table 2-3 defines the frost groups.

b. Depth of Frost Penetration. The depth of frost penetration is a function of the thermal properties of the pavement and soil mass, the surface temperature, and the temperature of the pavement and soil mass at the start of the freezing season. In determining the frost penetration depth, primary consideration should be given to local engineering experience. Residential construction practice, including the experience of local building departments, is generally the best guide to frost penetration depth.

c. Free Water. The availability of free water in the soil mass to freeze and form ice lenses is the third consideration that must be present for detrimental frost action to occur. Water can be drawn from considerable depths

9/30/2009 AC 150/5320-6E by capillary action, by infiltration from the surface or sides, or by condensation of atmospheric water vapor. Generally speaking, if the degree of saturation of the soil is 70 percent or greater, frost heave will probably occur. For all practical purposes, the designer should assume that sufficient water to cause detrimental frost action will be present.

d. Frost Design. The design of pavements to offset seasonal frost effects is presented in Chapter 3. A more detailed and rigorous discussion of frost action and its effects can be found in Research Report No. FAA-RD-74- 030, Design of Civil Airfield Pavement for Seasonal Frost and Permafrost Conditions (see Appendix 4).

TABLE 2-3. SOIL FROST GROUPS

FROST GROUP KIND OF SOIL

PERCENTAGE FINER THAN 0.02 mm BY WEIGHT

SOIL CLASSIFICATION

FG-1 Gravelly Soils 3 to 10 GW, GP, GW-GM, GP-GM FG-2 Gravelly Soils Sands

10 to 20 3 to 5 GM, GW-GM, GP-GM, SW, SP, SM, SW-SM, SP-SM FG-3 Gravelly Soils Sands, except very fine silty sands Clays, PI above 12

Over 20 Over 15 -

GM, GC SM, SC CL, CH FG-4 Very fine silty sands All Silts Clays, PI = 12 or less Varved Clays and other fine grained banded sediments

Over 15 - - -

SM ML, MH CL, CL-ML CL, CH, ML, SM

208. PERMAFROST. In arctic regions, soils are often frozen at considerable depths year round. Seasonal thawing and refreezing of the upper layer of permafrost can lead to severe loss of bearing capacity and/or differential heave. In areas with continuous high-ice-content permafrost at shallow depths, satisfactory pavements are best ensured by restricting seasonal thawing to the pavement and to a non-frost susceptible base course. This approach is intended to prevent degradation (thawing) of the permafrost layer.

a. Susceptibility. The frost susceptibility of soils in permafrost areas is classified the same as given above in paragraph 207.

b. Depth of Thaw Penetration. Pavement design for permafrost areas must consider the depth of seasonal thaw penetration. Although the Modified Berggren equation (see reference 18, Appendix 4) can theoretically be used with local climatic data to approximate the depth of thawing in permafrost, there are currently no software programs available to do this. However, the depth to which thawing temperatures penetrate into permafrost may be estimated using figure 2-2. Use of figure 2-2 requires inputs of air thawing index, average wind speed during the thaw period, pavement type, and density of the permafrost layer. The air thawing index is expressed in degree days and is the difference between average daily temperature and 32 degrees Fahrenheit (0 degrees Celsius) multiplied by the number of days the temperature exceeds freezing. The thawing index used for design (design thawing index) should be based on the three warmest summers in the last 30 years of record. If 30-year records are not available, data from the warmest summer in the latest 10-year period may be used.

c. Muskeg. Muskeg is sometimes encountered in arctic areas. Muskeg is a highly organic soil deposit that is essentially a swamp. Every effort should be made to avoid pavement construction on this material. If construction in areas of muskeg is unavoidable and the soil survey shows the thickness of muskeg is less than 5 feet (1.5 m), the muskeg should be removed and replaced with granular fill. If the thickness of muskeg is too great to warrant removal and replacement, a 5-foot (1.5 m) granular fill should be placed over the muskeg. These thicknesses are based on experience and it should be anticipated that differential settlement will occur and considerable maintenance will be required to maintain a smooth surface. Use of a geosynthetic between the muskeg surface and the bottom of granular fill is recommended to prevent migration of the muskeg up into the granular till. In this application, the geosynthetic is considered to perform the function of separation. Additional information on the design and construction of geosynthetics performing the separation function within pavement sections is provided in FHWA-HI-95-038 (see Appendix 4).

d. Permafrost Design. Design of pavements in areas of permafrost is discussed in Chapter 3. Further information on permafrost can be found in Research Report No. FAA-RD-74-030 (see Appendix 4).

FIGURE 2-2. RELATIONSHIP BETWEEN AIR THAWING INDEX AND THAW PENETRATION INTO GRANULAR, NON-FROST

SUSCEPTABLE SUBGRADE SOIL

CHAPTER 3. PAVEMENT DESIGN FOR AIRPLANES WEIGHING

MORE THAN 30,000 POUNDS SECTION 1. DESIGN CONSIDERATIONS.

300. SCOPE. This chapter provides pavement design guidance for airfield pavements intended to serve airplanes with gross weights in excess of 30,000 pounds (13 608 kg). Chapter 5 discusses the design of pavements serving lighter airplanes with gross weights under 30,000 pounds (13 608 kg).

301. DESIGN PHILOSOPHY. The foreword of this AC describes the FAA policy of treating the design of airplane landing gear and the design and evaluation of airport pavements as three separate entities. The design of airport pavements is a complex engineering problem that involves a large number of interacting variables. This chapter presents pavement mechanistic design procedures that are implemented in the FAA Rigid and Flexible Iterative Elastic Layer Design (FAARFIELD) program. FAARFIELD implements both layered elastic-based and three-dimensional finite element-based design procedures for new and overlay designs of flexible and rigid pavements, respectively.

Because of thickness variations, the evaluation of existing pavements should be performed using the same method employed for design. Chapter 6 describes in detail procedures to use when evaluating pavements. Details on the development of the FAA method of design are as follows:

a. Flexible Pavements. For flexible pavement design, FAARFIELD uses the maximum vertical strain at the top of the subgrade and the maximum horizontal strain at the bottom of the asphalt surface layer as the predictors of pavement structural life. FAARFIELD provides the required thickness for all individual layers of flexible pavement (surface, base, and subbase) needed to support a given airplane traffic mix over a particular subgrade.

b. Rigid Pavements. For rigid pavement design, FAARFIELD uses the maximum horizontal stress at the bottom edge of the PCC slab as the predictor of pavement structural life. The maximum horizontal stress for design is determined using an edge loading condition. FAARFIELD provides the required thickness of the rigid pavement slab needed to support a given airplane traffic mix over a particular subgrade/subbase.

302. REPORTING PAVEMENT STRENGTH. When designing new pavements, summarize all pavement designs on FAA Form 5100-1, Airport Pavement Design, which is considered part of the Engineer’s Design Report. Submit the Engineer’s Design Report for FAA review and approval along with initial plans and specifications.

303. BACKGROUND. An airfield pavement and the airplanes that operate on it represent an interactive system that must be addressed in the pavement design process. Design considerations associated with both the airplanes and the pavement must be recognized in order to produce a satisfactory design. Producing a pavement that will achieve the intended design life will require careful construction control and some degree of maintenance. Pavements are designed to provide a finite life and fatigue limits are anticipated. Poor construction and a lack of preventative maintenance will shorten the service life of even the best-designed pavement.

a. Variables. The determination of pavement thickness requirements is a complex engineering problem. Pavements are subject to a wide variety of loading and climatic effects. The design process involves a large number of interacting variables, which are often difficult to quantify. Despite considerable research on this subject, it has been impossible to arrive at a direct solution for thickness requirements. For this reason, pavement engineers must base pavement thickness on a theoretical analysis of load distribution through pavements and soils, the analysis of experimental pavement data, and a study of the performance of pavements under actual service conditions. The FAA developed the FAARFIELD program using failure models based on full-scale tests conducted from the 1940s until the present. Pavements designed and constructed in accordance with FAA standards are intended to provide a minimum structural life of 20 years that is free of major maintenance if no major changes in forecast traffic are encountered. Rehabilitation of surface grades and renewal of skid-resistant properties may be needed before 20 years because of destructive climatic effects and the deteriorating effects of normal usage.

b. Structural Design. The structural design of airport pavements consists of determining both the overall pavement thickness and the thickness of the component parts of the pavement. There are a number of factors that influence the thickness of pavement required to provide satisfactory service. These include the magnitude and character of the airplane loads to be supported, the volume of traffic, the concentration of traffic in certain areas, and the strength of the subgrade soil and quality of materials that make up the pavement structure.

304. PAVEMENT DESIGN USING FAARFIELD.

a. Purpose. The design procedure presented in this chapter provides a method of design based on layered elastic and three-dimensional finite element-based structural analysis developed to calculate design thicknesses for airfield pavements. Layered elastic and three-dimensional finite element-based design theories were adopted to address the impact of new complex gear and wheel arrangements. The design method is computationally intense, so the FAA developed a computer program called FAARFIELD to help pavement engineers implement it.

b. Application. The procedures and design software identified in this chapter are intended to provide pavement thickness design standards for all airfield pavements. To aid in the design review, the summary information from the design software should be printed and included with the pavement design submittal. The summary information can be printed from the FAARFIELD Notes Window by clicking the ‘Save XML’ button. FAARFIELD then saves the information into an Extensible Markup Language (XML) format file for future import into FAA Form 5100-1.

FAARFIELD is based on the cumulative damage factor (CDF) concept, in which the contribution of each airplane in a given traffic mix to total damage is separately analyzed. Therefore, the FAARFIELD program should not be used to compare individual airplane pavement thickness requirements with the design methods contained in previous versions of the AC that are based on the “design aircraft” concept. Likewise, due care should be used when using FAARFIELD to evaluate pavement structures originally designed with the thickness design curves in previous versions of this AC. Any comparison between FAARFIELD and the design curve methodology from previous versions of this AC must be performed using the entire traffic mix.

c. Computer Program. The structural computations are performed by two subprograms within FAARFIELD. These subprograms are called LEAF and NIKE3D_FAA. LEAF is a layered elastic computational program implemented as a Microsoft WindowsTM dynamic link library written in Visual BasicTM 2005. NIKE3D_FAA is a three-dimensional finite element computational program implemented as a dynamic link library written in FORTRAN. NIKE3D_FAA is a modification of the NIKE3D program originally developed by the Lawrence Livermore National Laboratory (LLNL) of the U.S. Department of Energy and is distributed in compiled form under a software sharing agreement between LLNL and the FAA.

(1) Airplane Considerations. A wide variety of airplanes with pertinent pavement design characteristics are stored in the program library. The FAARFIELD internal airplane library is divided into six airplane groups: Generic, Airbus, Boeing, Other Commercial, General Aviation, and Military. The designer has considerable latitude in selecting and adjusting airplane weights and frequencies.

(i) Load. The pavement design method is based on the gross weight of the airplane. The pavement should be designed for the maximum anticipated takeoff weight of the airplane at the anticipated facility. The design procedure assumes 95 percent of the gross weight is carried by the main landing gears and 5 percent is carried by the nose gear. FAARFIELD provides manufacturer-recommended gross operating weights for many civil and military airplanes. The FAA recommends using the maximum anticipated takeoff weight, which provides some degree of conservatism in the design. This will allow for changes in operational use and forecast traffic. The conservatism is offset somewhat by ignoring arriving traffic.

(ii) Landing Gear Type and Geometry. Gear type and configuration dictate how airplane weight is distributed to a pavement and how the pavement will respond to airplane loadings. Table 3-1 shows typical gear configurations and new gear designations in accordance with FAA Order 5300.7, Standard Naming Convention for Aircraft Landing Gear Configurations (Appendix 2).

(iii) Tire Pressure. Tire pressure varies depending on gear configuration, gross weight, and tire size. Tire pressure has significantly more influence on strains in the asphalt surface layer than at the subgrade. Tire pressures in excess of 221 psi (1.5 MPa) may be safely exceeded if the pavement surface course and base course meet the minimum design requirements for pavement loading along with a high stability asphalt surface.

(iv) Traffic Volume. Forecasts of annual departures by airplane type are needed for pavement design. Information on airplane operations is available from Airport Master Plans, Terminal Area Forecasts, the National Plan of Integrated Airport Systems, Airport Activity Statistics, and FAA Air Traffic Activity Reports. Pavement engineers should consult these publications when developing forecasts of annual departures by airplane type.

TABLE 3-1. STANDARD NAMING CONVENTION FOR COMMON AIRPLANE GEAR

CONFIGURATIONS

Gear Designation Gear Designation Airplane Example

S

Single

Sngl Whl-45

D

Dual

B737-100

2S

2 Singles in Tandem

C-130

2D

2 Duals in Tandem

B767-200

3D

3 Duals in Tandem

B777-200

2T

Two Triple Wheels in Tandem

C-17A

TABLE 3-1. STANDARD NAMING CONVENTION FOR COMMON AIRPLANE GEAR

CONFIGURATIONS (CONTINUED)

Gear Designation Gear Designation Airplane Example

2D/D1

Two Dual Wheels in Tandem Main Gear/Dual

Wheel Body Gear

DC10-30/40

2D/2D1

2D/2D1 Two Dual Wheels in Tandem Main Gear/Two Dual Wheels in Tandem Body Gear

A340-600 std

2D/2D2

Two Dual Wheels in Tandem Main Gear/Two

Dual Wheels in Tandem Body Gear

B747-400

2D/3D2

Two Dual Wheels in Tandem Main Gear/Three

Dual Wheels in Tandem Body Gear

A380-800

5D

Five Dual Wheels in Tandem Main Gear

An-124

(2) Units. The program may be operated with U.S. customary or metric dimensions.

(3) Availability. FAARFIELD can be downloaded from the Office of Airport Safety and Standards website (http://www.faa.gov/airports/).

(4) Related Reference Material. The internal help file for FAARFIELD contains a user’s manual, which provides detailed information on proper execution of the program. The manual also contains additional technical references for specific details of the FAARFIELD design procedure.

(5) Airplane Traffic Mixture. FAARFIELD was developed and calibrated specifically to produce pavement thickness designs consistent with previous methods based on a mixture of different airplanes rather than an individual airplane. If a single airplane is used for design, a warning will appear in the Airplane Window indicating a non-standard airplane list is used in the design. This warning is intended to alert the user that the program was intended for use with a mixture of different airplane types. Nearly any traffic mix can be developed from the airplanes in the program library. Solution times are a function of the number of airplanes in the mix. The FAARFIELD design procedure deals with mixed traffic differently than did previous design methods. Determination of a design aircraft is not required to operate FAARFIELD. Instead, the program calculates the damaging effects of each airplane in the traffic mix. The damaging effects of all airplanes are summed in accordance with Miner’s law. When the cumulative damage factor (CDF) sums to a value of 1.0, the design conditions have been satisfied.

d. Pavement Design Considerations. There are distinct differences between the previous FAA design methodology and the methodology contained in FAARFIELD. These differences, along with some common design assumptions between the two methods, are discussed below.

(1) Design Life. The FAA design standard for pavements is based on a 20-year design life. The computer program is capable of considering other design life time frames, but the use of a design life other than 20 years constitutes a deviation from FAA standards.

(2) Traffic Mix. The design procedures in previous versions of this AC required the traffic mixture to be converted into a single design aircraft and all annual departures converted to equivalent annual departures of the design aircraft. The design aircraft was determined by selecting the most damaging airplane based on the anticipated gross weight and the number of departures for each airplane. As noted in 303c(5), the FAARFIELD design program does not convert the traffic mixture to equivalent departures of a design aircraft. Instead, it analyzes the damage to the pavement for each airplane and determines a final thickness for the total cumulative damage. FAARFIELD considers the placement of each airplane’s main gear in relationship to the pavement centerline. It also allows the pavement damage associated with a particular airplane to be completely isolated from one or more of the other airplanes in the traffic mixture.

(3) Pass-to-Coverage Ratio. As an airplane moves along a pavement section it seldom travels in a perfectly straight path or along the exact same path as before. This lateral movement is known as airplane wander and is modeled by a statistically normal distribution. As an airplane moves along a taxiway or runway, it may take several trips or passes along the pavement for a specific point on the pavement to receive a full-load application. The ratio of the number of passes required to apply one full load application to a unit area of the pavement is expressed by the passto-coverage (P/C) ratio. It is easy to observe the number of passes an airplane may make on a given pavement, but the number of coverages must be mathematically derived based upon the established P/C ratio for each airplane. By definition, one coverage occurs when a unit area of the pavement experiences the maximum response (stress for rigid pavement, strain for flexible pavement) induced by a given airplane.

For flexible pavements, coverages are a measure of the number of repetitions of the maximum strain occurring at the top of subgrade. For rigid pavements, coverages are a measure of repetitions of the maximum stress occurring at the bottom of the PCC layer (see Report No. FAA-RD-77-81, Development of a Structural Design Procedure for Rigid Airport Pavements). Coverages resulting from operations of a particular airplane type are a function of the number of airplane passes, the number and spacing of wheels on the airplane main landing gear, the width of the tire-contact area, and the lateral distribution of the wheel-paths relative to the pavement centerline or guideline markings (see Report No. FAA-RD-74-036, Field Survey and Analysis of Aircraft Distribution on Airport Pavements). In calculating the P/C ratio, FAARFIELD uses the concept of effective tire width. For rigid pavements, the effective tire width is defined at the surface of the pavement and is equal to a nominal tire contact patch width.

For flexible pavements, for the failure mode of shear in the subgrade layer, the effective tire width is defined at the top of the subgrade. “Response lines” are drawn at a 1:2 slope from the edges of the contact patches to the top of the subgrade, as illustrated in figures 3-1 and 3-2. Tires are considered to be either separate or combined,

depending on whether the response lines overlap. Figures 3-1 and 3-2 are shown for information only. All effective tire width and P/C ratio calculations are performed internally within the FAARFIELD program.

(4) Annual Departures and Traffic Cycles. Airport pavement design using FAARFIELD considers only departures and ignores the arrival traffic when determining the number of airplane passes. This is because in most cases airplanes arrive at an airport at a significantly lower weight than at takeoff due to fuel consumption. During touchdown impact, remaining lift on the wings further alleviates the dynamic vertical force that is actually transmitted to the pavement through the landing gears. The FAA has defined a standard traffic cycle (TC) as one takeoff and one landing of the same airplane. In the situation described above, one traffic cycle produces one pass of the airplane which results in a pass-to-traffic cycle ratio (P/TC ) of 1. To determine annual departures for pavement design purposes multiply the number of departing airplanes by the P/TC. For most airport pavement design purposes, a P/TC of 1 may be used.

In cases where the landing weight is not significantly less than the take off weight or in a case where the airplane must travel along the pavement more than once, it may be appropriate to adjust the number of annual departures used for thickness design to reflect a different pass-to-traffic cycle (P/TC) ratio. For example, in the case of a runway with a central taxiway configuration the airplane is required to traffic a large part of the runway during the taxi movement. In this case the airplane must travel along the same portion of the runway pavement two times during the take off operation. For this scenario a P/TC ratio of 2 would be used (assuming that the airplane obtains fuel at the airport), and the number of annual departures used for design should accordingly be increased by a factor of 2. Additional definitions and guidance on determining the P/TC ratio may be found in AC 150/5335-5, “Standardized Method of Reporting Airport Pavement Strength – PCN,” Appendix 1.

(5) Cumulative Damage Factor. In FAARFIELD, the “design aircraft” concept has been replaced by design for fatigue failure expressed in terms of a cumulative damage factor (CDF) using Miner’s rule, CDF is the amount of the structural fatigue life of a pavement that has been used up. It is expressed as the ratio of applied load repetitions to allowable load repetitions to failure. For a single airplane and constant annual departures, CDF is expressed as—

failure to s repetition allowable of number

s repetition load applied of number CDF 

or   

  failure to coverages ratio coverage pass

years in life departures annual CDF

    

 

or

failure to coverages

coverages applied CDF 

Table 3-2 describes pavement condition for different values of CDF.

TABLE 3-2. PAVEMENT REMAINING LIFE BASED ON CDF VALUE

CDF value Pavement Remaining Life 1 The pavement has used up all of its fatigue life. < 1 The pavement has some life remaining, and the value of CDF gives the fraction of the life used. > 1 The pavement has exceeded its fatigue life.

In the program implementation, CDF is calculated for each 10-inch (254 mm) wide strip along the pavement over a total width of 820 inches (20 828 mm). Pass-to-coverage ratio is computed for each strip based on a normally distributed

9/30/2009 AC 150/5320-6E airplane wander pattern with standard deviation of 30.435 inches (773 mm) (equivalent to airplane operation on a taxiway) and used in the above equation for Miner’s rule. The CDF for design is taken to be the maximum over all 82 strips. Even with the same gear geometry, therefore, airplanes with different main gear track widths will have different pass-to-coverage ratios in each of the 10-inch (254 mm) strips and may show little cumulative effect on the maximum CDF. Removing the airplanes with the lowest stress or strain may then have little effect on the design thickness, depending on how close the gear tracks are to each other and the number of departures.

FIGURE 3-1. TWO EFFECTIVE TIRE WIDTHS - NO OVERLAP

FIGURE 3-2. ONE EFFECTIVE TIRE WIDTH – OVERLAP

Example: To illustrate the results of CDF calculations, an existing taxiway pavement composed of the following section was assumed: the subgrade k-value is 141 pci (38.4 MN/m3), equivalent to an E modulus of 15,000 psi (103.42 MPa), the PCC surface course is 15.2 inches (386 mm) thick, the P-306 econocrete base course is 6 inches (152 mm) thick, and the P-209 crushed aggregate subbase course is 6 inches (152 mm). The pavement is designed for the following airplane mix: B747-200B Combi Mixed weighing 836,000 pounds (379 203 kg) at an annual departure level of 1,200, B777-200 ER weighing 657,000 pounds (298 010 kg) at an annual departure level of 1,200, and DC8-63/73 weighing 358,000 pounds (162 386 kg) at an annual departure level of 1,200. The CDF contributions for each individual airplane and the cumulative CDF across the pavement section are shown on figure 3-3. Values of individual airplane contributions depend on several factors of which the most important are annual departure level and airplane gross weight.

FIGURE 3-3. EXAMPLE OF CDF CONTRIBUTION FOR AIRPLANE MIX

(6) Materials. In the FAARFIELD design procedure, pavement layers are assigned a thickness, elastic modulus, and Poisson’s ratio. The same layer properties are used in layered elastic and finite element analysis mode. Layer thicknesses can be varied, subject to minimum thickness requirements. Elastic moduli are either fixed or variable, depending on the material. The permissible range of variability for elastic moduli is fixed to ensure reasonable values. Poisson’s ratio for all materials is fixed. Materials are identified by their corresponding FAA specification designations; for example, crushed stone base course is identified as Item P-209. The list of materials contains an undefined layer with variable properties. If an undefined layer is used, a warning will appear in the Structure Window stating that a non-standard material has been selected and its use in the structure will require FAA approval.

(7) Minimum Layer Thickness. When used in accordance with the user’s manual, FAARFIELD will automatically establish the minimum layer thickness for each layer, as required. However, it is recommended that the user consult the applicable paragraphs of this AC for design of new flexible, new rigid, and overlaid pavements to assure that the minimum thickness requirements are obtained.

305. TRAFFIC DISTRIBUTION. Research studies have shown that airplane traffic is distributed laterally on runways and taxiways according to statistically normal (bell-shaped) distribution. FAA Report No. FAA-RD-74-036 contains research information on traffic distribution. The design procedures presented in this AC incorporate the statistically normal distribution in the departure levels. In addition to the lateral distribution of traffic across pavements, it also considers traffic distribution and the nature of loadings for aprons and high-speed turnoffs.

306. TYPICAL SECTIONS. Airport pavements are generally constructed in uniform, full-width sections. Runways may be constructed with a transversely variable section, if practical or economically feasible. A variable section permits a reduction in the quantity of materials required for the upper paving layers of the runway. However, more complex construction operations are associated with variable sections and are usually more costly. The additional construction costs may negate any savings realized from reduced material quantities. Typical plan and section drawings for transversely variable section runway pavements are shown in figure 3-4. Deviations from these typical sections will be common due to the change inherent in staged construction projects where runways are extended and the location of

9/30/2009 AC 150/5320-6E taxiways is uncertain. As a general rule-of-thumb the designer should specify full pavement thickness where departing traffic will be using the pavement; pavement thickness designed using arrivals weight and estimated frequency where traffic will be arrivals such as high speed turnoffs; and pavement thickness designed using departure weight and 1 percent of estimated frequency where pavement is required but traffic is unlikely such as along the extreme outer edges of the runway. Note that the full-strength keel section is 50 feet (15 m) on the basis of the research study discussed in paragraph 305.

307. FROST AND PERMAFROST DESIGN. The design of an airport pavement must consider the climatic conditions that will act on the pavement during its construction and service life. The protection of pavements from the adverse effects of seasonal frost and permafrost effects are considered in the design of airport pavements as discussed below.

a. Seasonal Frost. The adverse effects of seasonal frost are discussed in Chapter 2. The design of pavements in seasonal frost areas may be based on either of two approaches. The first approach is based on the control of pavement deformations resulting from frost action. Under this approach, sufficient combined thickness of pavement and non-frost-susceptible material must be provided to eliminate, or limit to an acceptable amount, frost penetration into the subgrade and its adverse effects. The second approach is based on providing adequate pavement load carrying capacity during the critical frost melting period. The second approach provides for the loss of load carrying capacity due to frost melting but ignores the effects of frost heave. Three design procedures that encompass the above approaches have been developed and are discussed below.

(1) Complete Frost Protection. Complete frost protection is accomplished by providing a sufficient thickness of pavement and non-frost-susceptible material to totally contain frost penetration. This method is intended to prevent underlying frost susceptible materials from freezing. To use the complete protection method, the depth of frost penetration is determined by local experience or engineering analysis following the procedure given in Chapter 2. The thickness of pavement required for structural support is compared with the depth of frost penetration computed. The difference between the pavement thickness required for structural support and the computed depth of frost penetration is made up with non-frost susceptible material. Depending on grades and other considerations, provision for complete protection may involve removal and replacement of a considerable amount of subgrade material. Complete frost protection is the most positive, and is usually the most costly, method of providing frost protection.

(2) Limited Subgrade Frost Penetration. The limited subgrade frost penetration method is based on holding frost heave to a tolerable level. Frost is allowed to penetrate a limited amount into the underlying frost susceptible subgrade. Sixty-five percent of the depth of frost penetration is made up with non-frost-susceptible material. Use of the method is similar to the complete protection method. Additional frost protection is required if the thickness of the structural section is less than 65 percent of the frost penetration. The limited subgrade frost penetration method allows a tolerable (based on experience) amount of frost heave.

(3) Reduced Subgrade Strength. The reduced subgrade strength method is based on the concept of providing a pavement with adequate load carrying capacity during the frost melting period. This method does not consider the effects of frost heave. Use of the reduced subgrade strength method involves assigning a subgrade strength rating to the pavement for the frost melting period. The various soil frost groups, as defined in Chapter 2, should be assigned strength ratings as shown below:

TABLE 3-3. REDUCED SUBGRADE STRENGTH RATINGS

Frost Group Flexible Pavement CBR Value Rigid Pavement k-value FG-1 9 50 FG-2 7 40 FG-3 4 25 FG-4 Reduced Subgrade Strength Method Does Not Apply

The required pavement thicknesses are determined using FAARFIELD, using the reduced subgrade strength value from table 3-3 in lieu of the nominal subgrade CBR or k-value determined by testing. Pavement thicknesses thus established reflect the requirements for the subgrade in its weakened condition due to frost melting.

b. Applications. Due to economic considerations, the maximum practical depth of frost protection that should be provided is normally 72 inches (1 829 mm). The recommended applications of the three methods of frost protection discussed above are as follows. In addition to these recommended applications, local experience should be given strong consideration when designing for frost conditions.

(1) Complete Frost Protection. The complete frost protection method applies only to FG-3 and FG-4 soils, which are extremely variable in horizontal extent. These soil deposits are characterized by very large, frequent, and abrupt changes in frost heave potential. The variability is such that the use of transition sections is not practical.

(2) Limited Subgrade Frost Penetration. This design method should be used for FG-4, soils except where the conditions require complete protection, see (1) above. The method also applies to soils in frost groups FG-1, FG-2, and FG-3 when the functional requirements of the pavement permit a minor amount of frost heave. Consideration should be given to using transition sections where horizontal variability of frost heave potential permits.

(3) Reduced Subgrade Strength. The reduced subgrade strength method is recommended for FG-1, FG-2, and FG-3 subgrades, which are uniform in horizontal extent or where the functional requirements of the pavement will permit some degree of frost heave. The method may also be used for variable FG-1 through FG-3 subgrades for less sensitive pavements, which are subject to slow speed traffic and heave can be tolerated.

c. Permafrost. The design of pavements in permafrost regions must consider not only the effects of seasonal thawing and refreezing, but also the effects of construction on the existing thermal equilibrium. Changes in the subsurface thermal regime may cause degradation of the permafrost table, resulting in severe differential settlements and drastic reduction of pavement load carrying capacity. Gravel surfaced pavements are rather common in permafrost areas and generally will provide satisfactory service. These pavements often exhibit considerable distortion but are rather easily regraded. The absence of a waterproof surface is not a great problem because these areas usually have low precipitation. Three design methods for asphaltic or concrete surfaced pavements are discussed below.

(1) Complete Protection Method. The objective of the complete protection method is to ensure that the underlying permafrost remains frozen year-round. Seasonal thawing is restricted to non-frost-susceptible materials. This method is analogous to the complete frost protection method of design for seasonal frost. The thickness of pavement required for structural support is first determined. The depth of seasonal thaw is then computed as described in Chapter 2 or using information based on local experience. The difference between the depth of seasonal thaw and the thickness needed for structural support is the amount of non-frost-susceptible material that must be provided to fully contain the depth of seasonal thaw. The use of relatively high moisture retaining soils, such as uniformly graded sands, should be considered. If some heaving can be tolerated, the use of frost-susceptible soils in the FG-1 or FG-2 groups may also be considered. If FG-1 or FG-2 soils are used, they must be placed so as to be as uniform as possible. Normally, economic considerations will limit the depth of treatment to a maximum of 6 feet (1.8 m).

(2) Reduced Subgrade Strength Method. If conditions are such that the complete protection method of design is not practical, the design may be based on the reduced subgrade strength method. The use of this method for permafrost design is identical to that presented in paragraph 307b(3) above. This method should provide a pavement with sufficient structural support during the seasonal permafrost thaw period but will likely result in differential heaving. If practical, it may be advisable to delay paving for 2 or 3 years to allow the embankment to reach equilibrium.

(3) Insulating Panels. A third approach, which is not as common, is the use of insulating panels beneath the pavement structure to protect against degradation of the permafrost. This method can lead to problems if the insulating panels are crushed by the weight of the overburden or by the live loads. Crushing of the cell structure of the insulation results in loss of insulating properties and failure to serve its intended purpose. Pavements using this technique must be very carefully constructed and may be subject to load limitations because of the need to guard against crushing the insulating panels. A significant change in the weight of using airplanes may fail the insulating panels. Since the FAA has no standards or design criteria for the use of insulating panels, the FAA must approve their use on federally funded construction on a case-by-case basis.

FIGURE 3-4. TYPICAL PLAN AND CROSS SECTION FOR RUNWAY PAVEMENT

FOREWORD › SECTION 2. FLEXIBLE PAVEMENT DESIGN

SECTION 2. FLEXIBLE PAVEMENT DESIGN

308. GENERAL. Flexible pavements consist of a hot mix asphalt wearing surface placed on a base course and, when required by subgrade conditions, a subbase. The entire flexible pavement structure is ultimately supported by the subgrade. Definitions of the function of the various components are given in the following paragraphs.

309. HOT MIX ASPHALT SURFACING. The hot mix asphalt surface or wearing course must prevent the penetration of surface water to the base course; provide a smooth, well-bonded surface free from loose particles which might endanger airplanes or persons; resist the shearing stresses induced by airplane wheel loads; and furnish a texture of nonskid qualities, yet not cause undue wear on tires. To successfully fulfill these requirements, the surface must be composed of mixtures of aggregates and bituminous binders which will produce a uniform surface of suitable texture possessing maximum stability and durability. Since control of the mixture is of paramount importance, these requirements can best be achieved by use of a central mixing plant where proper control can be most readily obtained. A dense-graded hot mix asphalt concrete such as Item P-401 produced in a central mixing plant will most satisfactorily meet all the above requirements. Whenever a hot mix asphalt surface is subject to spillage of fuel, hydraulic fluid, or other solvents, such as at airplane fueling positions and maintenance areas, protection should be provided by a solvent resistant surface.

310. BASE COURSE. The base course is the principal structural component of the flexible pavement. It has the major function of distributing the imposed wheel loadings to the pavement foundation, the subbase and/or subgrade. The base course must be of such quality and thickness to prevent failure in the subgrade, withstand the stresses produced in the base itself, resist vertical pressures tending to produce consolidation and resulting in distortion of the surface course, and resist volume changes caused by fluctuations in its moisture content. The quality of the base course depends upon composition, physical properties and compaction. Many materials and combinations thereof have proved satisfactory as base courses. They are composed of select, hard, and durable aggregates. Specifications covering the quality of components, gradation, manipulation control, and preparation of various base materials for use on airports for airplane design loads of 30,000 pounds (13 608 kg) or more are as follows:

(1) Item P-208 – Aggregate Base Course¹

(2) Item P-209 – Crushed Aggregate Base Course2

(3) Item P-211 – Lime Rock Base Course

(4) Item P-219 – Recycled Concrete Aggregate Base Course

(5) Item P-304 – Cement Treated Base Course

(6) Item P-306 – Econocrete Subbase Course

(7) Item P-401 – Plant Mix Bituminous Pavements

(8) Item P-403 – HMA Base Course

¹The use of Item P-208, Aggregate Base Course, as base course is limited to pavements designed for gross loads of 60,000 lb (27 216 kg) or less. When Item P-208 is used as base course the minimum thickness of the hot mix asphalt surfacing should be 5 inches (127 mm).

2The use of item P-209, Crushed Aggregate Base Course, as a base course is limited to pavements serving airplanes having gross loads of 100,000 lbs (45 359 kg) or less except as noted in paragraph 317.

Rubblized Portland cement concrete can also be used as a base course for flexible pavement.

Depending on their composition, these materials have been divided into two major types: stabilized (P-211, P-304, P- 306, P-401, and P-403) and unstabilized (P-208, P-209, P-219, and rubblized Portland cement concrete) base courses. Details on these materials are described in paragraph 315d.

311. SUBBASE. A subbase is included as an integral part of the flexible pavement structure in all pavements except those on subgrades with a CBR value of 20 or greater (usually GW or GP type soils). The function of the subbase is similar to that of the base course. However, since it is further removed from the surface and is subjected to lower loading intensities, the material requirements are not as strict as for the base course. In the development of pavement thickness requirements the CBR value of the subbase course is a variable.

a. Quality. Specifications covering the quality of components, gradations, manipulation control, and preparation of various types of subbase courses for use on airports for airplane design loads of 30,000 pounds (13 608 kg) or more are as follows:

(1) Item P-154 – Subbase Course

(2) Item P-210 – Caliche Base Course

(3) Item P-212 – Shell Base Course

(4) Item P-213 – Sand Clay Base Course¹

(5) Item P-301 – Soil Cement Base Course¹

¹ Use of Items P-213 and P-301 as subbase course is not recommended where frost penetration into the subbase is anticipated.

Any material suitable for use as base course can also be used on subbase if economy and practicality dictate.

b. Sandwich Construction. Pavements should not be configured such that a pervious granular layer is located between two impervious layers. This type of section is often called sandwich construction. Problems are often encountered in sandwich construction when water becomes trapped in the granular layer causing a dramatic loss of strength and results in poor performance. A rubblized concrete layer over a stabilized base layer is not considered as sandwich construction.

312. SUBGRADE. The subgrade soils are subjected to lower stresses than the surface, base, and subbase courses. Subgrade stresses attenuate with depth, and the controlling subgrade stress is usually at the top of the subgrade, unless unusual conditions exist. Unusual conditions such as a layered subgrade or sharply varying water contents or densities can change the location of the controlling stress. The ability of a particular soil to resist shear and deformation vary with its density and moisture content. Such unusual conditions should be revealed during the soils investigation. Specification Item P-152, Excavation and Embankment, covers the construction and density control of subgrade soils. Table 3-4 shows depths below the subgrade surface to which compaction controls apply. To use table 3-4, consider the mix of the airplanes that will be using the pavement feature under consideration. The airplane in the mix that should be used to determine compaction requirements is the airplane requiring the maximum compaction depth from table 3-4, regardless of the anticipated number of operations.

a. Contamination. A loss of structural capacity can result from contamination of base or subbase elements with fines from underlying subgrade soils. This contamination occurs during pavement construction and during pavement loading. Aggregate contamination results in a reduced ability of the aggregate to distribute and reduce stresses applied to the subgrade. Fine grained soils are most likely to contaminate pavement aggregate. This process is not limited to soft subgrade conditions. Problematic soils may be cohesive or noncohesive and usually exhibit poor drainage properties. Chemical and mechanical stabilization of the subbase or subgrade can be effectively used to reduce aggregate contamination (refer to paragraph 206). Geosynthetics are effective at providing separation between finegrained soils and overlying pavement aggregates (FHWA-HI-95-038) (see Appendix 4). In this application, the geosynthetic is not considered to act as a structural element within the pavement. For separation applications the geosynthetic is designed based on survivability properties. Refer to FHWA-HI-95-038 (see Appendix 4) for additional information about design and construction using separation geosynthetics.

b. Example. An apron extension is to be built to accommodate the following airplane mix: B767-200 (340,000 lbs./154 221 kg), B757-200 (256,000 lbs./116 1200 kg), and A310-200 (315,041 lbs./142 900 kg). A soils investigation has shown the subgrade will be noncohesive. In-place densities of the soils have been determined at even foot increments below the ground surface. Design calculations indicate that the top of subgrade in this area will be approximately 10 inches (254 mm) below the existing grade. Depths and densities may be tabulated as follows in table 3-5.

TABLE 3-4. SUBGRADE COMPACTION REQUIREMENTS FOR FLEXIBLE PAVEMENTS

NON-COHESIVE SOILS Depth of Compaction, inch

COHESIVE SOILS Depth of Compaction, inch GEAR TYPE GROSS WEIGHT Lb. 100% 95% 90% 85% 95% 90% 85% 80% 30,000 8 8-18 18-32 32-44 6 6-9 9-12 12-17 50,000 10 10-24 24-36 36-48 6 6-9 9-16 16-20 S

75,000 12 12-30 30-40 40-52 6 6-12 12-19 19-25 50,000 12 12-28 28-38 38-50 6 6-10 10-17 17-22 100,000 17 17-30 30-42 42-55 6 6-12 12-19 19-25 150,000 19 19-32 32-46 46-60 7 7-14 14-21 21-28

D (incls. 2S)

200,000 21 21-37 37-53 53-69 9 9-16 16-24 24-32 100,000 14 14-26 26-38 38-49 5 6-10 10-17 17-22 200,000 17 17-30 30-43 43-56 5 6-12 12-18 18-26 300,000 20 20-34 34-48 48-63 7 7-14 14-22 22-29

2D (incls. B757, B767, A-300, DC- 10-10, L1011) 400,000 – 600,000 23 23-41 41-59 59-76 9 9-18 18-27 27-36

2D/D1, 2D/2D1 (incls. MD11, A340, DC10-30/40)

500,000 – 800,000 23 23-41 41-59 59-76 9 9-18 18-27 27-36

800,000 23 23-41 41-59 59-76 9 9-18 18-27 27-36 2D/2D2 (incls. B747 series) 975,000 24 24-44 44-62 62-78 10 10-20 20-28 28-37 550,000 20 20-36 36-52 52-67 6 6-14 14-21 21-29 650,000 22 22-39 39-56 56-70 7 7-16 16-22 22-30 3D (incls. B777 series)

750,000 24 24-42 42-57 57-71 8 8-17 17-23 23-30 1,250,000 24 24-42 42-61 61-78 9 9-18 18-27 27-36 2D/3D2 (incls. A380 series) 1,350,000 25 25-44 44-64 64-81 10 10-20 20-29 29-38 Notes: 1. Noncohesive soils, for the purpose of determining compaction control, are those with a plasticity index of less than 3. 2. Tabulated values denote depths below the finished subgrade above which densities should equal or exceed the indicated percentage of the maximum dry density as specified in Item P-152. 3. The subgrade in cut areas should have natural densities shown or should (a) be compacted from the surface to achieve the required densities, (b) be removed and replaced at the densities shown, or (c) when economics and grades permit, be covered with sufficient select or subbase material so that the uncompacted subgrade is at a depth where the in-place densities are satisfactory. 4. For intermediate airplane weights, use linear interpolation. 5. For swelling soils, refer to paragraph 313. 6. 1 inch = 25.4 mm, 1 pound. = 0.454 kg

TABLE 3-5. DENSITIES FOR SUBGRADE IN EXAMPLE

Depth Below Existing Grade

Depth Below Finished Grade

In-Place Density 1′ (0.3 m) 2″ (50 mm) 70% 2′ (0.6 m) 14″ (0.36 m) 84% 3′ (0.9 m) 26″ (0.66 m) 86% 4′ (1.2 m) 38″ (0.97 m) 90% 5′ (1.5 m) 50″ (1.27 m) 93%

For this example, the B767-200 gives the maximum required compaction values from table 3-4. Using table 3-4 for non-cohesive soils and applying linear interpolation, obtain the following compaction requirements as shown in table 3- 6.

TABLE 3-6. COMPACTION REQUIREMENTS FOR EXAMPLE

100% 95% 90% 85% 0-21 21-37 37-52 52-68

Comparison of the tabulations show that for this example in-place density is satisfactory at a depth of 38 inches (0.97 m), being 90 percent within the required 90 percent zone. It will be necessary to compact an additional 1 inch (0.03 m) at 95 percent. Therefore, compact the top 21 inches (0.53 m) of subgrade at 100 percent density and the 21 to 38 inches at 95 percent density.

313. SWELLING SOILS. Swelling soils are clayey soils that exhibit significant volume changes brought on by moisture variations. The potential for volumetric change of a soil due to moisture variation is a function of the type of soil and the likelihood of moisture fluctuation. Airport pavements constructed on these soils are subject to differential movements causing surface roughness and cracking. The design of pavements in areas of swelling soils should incorporate methods that prevent or reduce the effects of soil volume changes.

a. Soil Type. Only clayey soils containing a significant amount of particular clay minerals are prone to swelling. The clay minerals that cause swelling, in descending order of swelling activity, are: smectite, illite, and kaolinite. These soils usually have liquid limits above 40 and plasticity indexes above 25.

b. Identification. Soils that exhibit a swell of greater than 3 percent when tested for the CBR (California Bearing Ratio), ASTM D 1883, require treatment. Experience with soils in certain locales is often used to determine when treatment is required.

c. Treatment. Treatment of swelling soils consists of removal and replacement, stabilization, modified compaction efforts and careful control of compaction moisture. Provisions for adequate drainage are of paramount importance when dealing with swelling soils. Recommended treatments for swelling soils are shown in table 3-7. Local experience and judgment should be applied in dealing with swelling soils to achieve the best results. Care should be taken to minimize water flow along the contact plane between the stabilized / nonstabilized material.

TABLE 3-7. RECOMMENDED TREATMENT OF SWELLING SOILS

Swell Potential (Based on Experience)

Percent Swell Measured (ASTM D 1883)

Potential for Moisture Fluctuation1

Treatment

Low Compact soil on wet side of optimum (+2% to +3%) to not greater than 90% of appropriate maximum density2. Low 3-5

High Stabilize soil to a depth of at least 6 in. (150 mm) Low Stabilize soil to a depth of at least 12 in. (300 mm) Medium 6-10 High Stabilize soil to a depth of at least 12 in. (300 mm) Low Stabilize soil to a depth of at least 12 in. (300 mm) High Over 10

High For uniform soils, i.e., redeposited clays, stabilize soil to a depth of at least 36 in. (900 mm) or raise grade to bury swelling soil at least 36 in. (900 mm) below pavement section or remove and replace with nonswelling soil. For variable soil deposits depth of treatment should be increased to 60 in. (1 500 mm). Notes: 1Potential for moisture fluctuation is a judgmental determination and should consider proximity of water table, likelihood of variations in water table, as well as other sources of moisture, and thickness of the swelling soil layer. 2When control of swelling is attempted by compacting on the wet side of optimum and reduced density, the design subgrade strength should be based on the higher moisture content and reduced density.

d. Additional Information. Additional information on identifying and handling swelling soils is presented in FAA Reports No. FAA-RD-76-066, Design and Construction of Airport Pavements on Expansive Soils, and DOT/FAA/PM-85115, Validation of Procedures for Pavement Design on Expansive Soils.

314. SELECTION OF DESIGN CBR VALUE. Subgrade soils are usually rather variable and the selection of a design CBR value requires some judgment. The design CBR value should be equal to or less than 85 percent of all the

subgrade CBR values. This corresponds to a design value of one standard deviation below the mean. In some cases subgrade soils that are significantly different in strength occur in different layers. In these instances several designs should be examined to determine the most economical pavement section. It may be more economical to remove and replace a weak layer than to design for it. On the other hand, circumstances may be such that designing for the weakest layer is more economical. Local conditions will dictate which approach should be used.

315. FLEXIBLE PAVEMENT DESIGN. The design process for flexible pavement considers two modes of failure for flexible pavement: vertical strain in the subgrade and horizontal strain in the asphalt layer. Limiting vertical strain in the subgrade is intended to preclude failure by subgrade rutting. Limiting horizontal strain at the bottom of the asphalt surfacing layer guards against pavement failure initiated by cracking of the asphalt surface layer. By default, FAARFIELD computes only the vertical subgrade strain for flexible pavement thickness design. However, the user has the option of enabling the asphalt strain computation by deselecting the “No AC CDF” checkbox in the FAARFIELD options screen. In most cases the thickness design is governed by the subgrade strain criterion. The user has the option of performing the asphalt strain check for the final design, and it is good engineering practice to do so.

a. Design Life. The FAA design standards for airport pavements use the 20 year structural design life criteria as a policy. FAARFIELD is capable of considering design life timeframes other than the 20 year life criteria, but they are considered a deviation from FAA standards.

b. Traffic Mix. Input the complete air traffic mix into FAARFIELD. See paragraph 304c(5).

c. Hot Mix Asphalt Surfacing. Hot mix asphalt surfacing should meet the requirements of FAA Item P-401. A minimum thickness of 4 inches (102 mm) of hot mix surfacing is required. A fixed modulus value for hot mix surfacing is set in the program at 200,000 psi (1 380 MPa). This modulus value was conservatively chosen and corresponds to a pavement temperature of approximately 90 ºF (32ºC).

Two types of asphalt surface layers are available in FAARFIELD: asphalt surface and asphalt overlay. Both have the same properties, with modulus fixed at 200,000 psi (1 380 MPa) and Poisson’s ratio fixed at 0.35. The asphalt overlay type can be placed over asphalt surface or PCC surface types. The asphalt surface type can only be placed on the top of a structure, or under an asphalt overlay.

d. Base Course. Two types of base courses are defined: stabilized and unstabilized (aggregate). A stabilized base course may be required as described in paragraph 317.

(1) Stabilized Base Course. FAARFIELD includes two types of stabilized layers, classified as stabilized (flexible) and stabilized (rigid). Variable modulus types are provided as well as fixed modulus types corresponding to standard material items. The two stabilized flexible base options are designated P-401/P-403 and Variable. The word flexible is used to indicate that these bases have a higher Poisson’s ratio (0.35), act as flexible layers as opposed to rigid layers, and are not likely to crack. The standard FAA bituminous base is P-401/P-403, which has a fixed modulus of 400,000 psi (2 760 MPa). The variable stabilized flexible base can be used to characterize a stabilized base, which does not conform to the properties of P-401/P-403. It has a variable modulus ranging from 150,000 to 400,000 psi (1 035 to 2 760 MPa). Stabilized (rigid) bases, P-304, and P-306 may also be used as base courses in flexible pavements. Item P-301, Soil Cement Base, is not acceptable for use as a stabilized base course for flexible pavements. The properties of the various stabilized base layer types used in FAARFIELD are summarized in table 3-8.

TABLE 3-8. LAYER TYPES IN FAARFIELD

Base Layer Modulus, psi (MPa) Poisson’s Ratio Stabilized (flexible) Variable Minimum Variable Maximum P-401/403 Asphalt

150,000 (1 035) 400,000 (2 760) 400,000 (2 760)

0.35

Stabilized (rigid) Variable Minimum Variable Maximum P-304 Cement Treated Base P-306 Econocrete Subbase

250,000 (1 720) 700,000 (4 830) 500,000 (3 450) 700,000 (4 830)

0.20

The above minimum and maximum modulus values were determined on the basis of producing thickness designs comparable with the CBR design procedures. Therefore, typical laboratory test data for stabilized materials should not

9/30/2009 AC 150/5320-6E be used in preparing input data for FAARFIELD designs. If it is necessary to establish a modulus for a variable base layer the following guidance should be used:

For flexible pavement design, the minimum modulus value of 150,000 psi (1 034 MPa) corresponds to a base course equivalency factor of 1.2 and the maximum value of 400,000 psi (2 758 MPa) corresponds to a base course equivalency factor of 1.6 previously used in CBR method. The equivalency factor represents the ratio of the thickness of a standard aggregate base layer (Item P-208) to a base layer of higher quality in the CBR method. The choice of base course modulus value can have a significant effect on total thickness of a flexible pavement.

When a variable modulus layer is first created, the modulus is automatically set to the minimum value.

(2) Unstabilized (Aggregate) Base Course. The standard aggregate base course for flexible pavement design is Item P-209, Crushed Aggregate Base Course. In FAARFIELD, P-209 Crushed Aggregate corresponds to the standard material. Item P-208, Uncrushed Aggregate, is not suitable as a base course material. Item P-208, when used as a base course is subject to the restrictions in paragraph 310. The modulus of aggregate layers is computed automatically and cannot be changed manually.

To compute the modulus of non-stablized layers, the “Modulus” procedure developed by the U.S. Army Corps of Engineers Waterways Experiment Station is followed with sublayering performed automatically (maximum sublayer thicknesses are 8 inches (203 mm) for uncrushed aggregate and 10 inches (254 mm) for crushed aggregate). The modulus values of the sublayers decrease with increasing depth of a sublayer within the aggregate layer and are also dependent on the modulus of the layer below the aggregate layer.

Aggregate layers can be placed anywhere in the pavement structure except at the surface or subgrade. The following additional restrictions also apply:

 Only one crushed layer and one uncrushed layer may be present in a structure. This is for compatibility with the “Modulus” procedure. (Sublayering by the “Modulus” procedure accounts for thick layers, and multiple layers of a single aggregate type are not necessary.) The maximum number of aggregate layers that may be present in a structure is therefore two, one of each type.

 If crushed and uncrushed layers are adjacent, the crushed layer must be above the uncrushed layer (to be compatible with the “Modulus” procedure).

The modulus value displayed in the structure table for an aggregate layer is the average value of the sublayer modulus values. The only exception is for newly created layers, in which case the modulus values of 75,000 psi (517 MPa) and 40,000 psi (276 MPa) are displayed for crushed and uncrushed respectively. These default modulus values are never used in calculations.

(3) Minimum Base Course Thickness. FAARFIELD, by default, computes the structural thickness required for the base course. Since it is assumed that the subbase layer provides the equivalent bearing capacity of a CBR 20 subgrade, the structural base course thickness is computed as the thickness required to protect a subgrade of CBR 20.

When an aggregate base course is used, the automatic base thickness design procedure in FAARFIELD consists of two steps:

Step 1 Compute the aggregate base thickness structurally required to protect an assumed CBR 20 subgrade. Step 2 Compare the base thickness computed in step 1 against the minimum base thickness requirements in table 3-9.

Select the thicker of the two values as the design base course thickness.

For traffic mixtures with airplanes exceeding 100,000 pounds (45 400 kg), a stabilized base course is required as described in paragraph 317. The minimum stabilized base thickness is 5 inches (127 mm). When a stabilized base is used, an additional step is added to the automated base thickness design procedure. After the thickness of the aggregate base structurally required to protect a CBR 20 subgrade is computed (step 1 above), the required thickness of the stabilized base is obtained by dividing by 1.6. The required stabilized base thickness thus obtained is compared with the 5 inch (127 mm) minimum requirement, and the larger of the two values is selected as the design stabilized base course thickness.

TABLE 3-9. MINIMUM AGGREGATE BASE COURSE THICKNESS

Design Load Range Minimum Base Course (P-209) Thickness Gear Type

lbs (kg) in. (mm) 30,000 - 50,000 (13 600 – 22 700) 4 (100) S

50,000 - 75,000 (22 700 – 34 000) 6 (150) 50,000 - 100,000 (22 700 – 45 400) 6 (150) D

Continue reading ↓ 120 of 343 passages shown