AC 150/5320-6D Airport Pavement Design and Evaluation
Provides guidance to the public for the design and evaluation of pavements at civil airports.
This document is cancelled. It may have been replaced. Check the official source before relying on it.
Text read by OCR from a scanned file (9 of 165 pages). Check the original, as some words may be misread.
.-
U.S. Department of Transportation
Federal Aviation Administration
Advisory
Circular
Subject: AIRPORT PAVEMENT DESIGN AND Date: 7/7/95 EVALUATION Initiated by: AAS-
AC No: 150/5320-6D Change:
1. PURPOSE. This advisory circular provides guidance to the public for the design and evaluation of pavements at civil airports.
2. CANCELLATION. AC 150/5320-6C, Airport Pavement Design and Evaluation, dated December 7, 1978, is canceled.
3. APPLICATION. The guidelines contained herein are recommended by the Federal Aviation Administration for applications at airports as appropriate.
4. RELATED READING MATERIAL. The publications listed in Appendix 4 provide further guidance and detailed information on the design and evaluation of airport pavements.
5. METRIC UNITS. To prl)mote an orderly transition to metric units, this advisory circular includes both English and metric dimensions. The metnc conversions may not be the exact equivalents, and until an official changeover to metric units is effected, the English dimensions will be used.
-’ RAYMOND T. UHL Acting Director, Office of Airport Safety and Standards
CANCELLED
7t7195 AC 150/5320-6D
CONTENTS FOREWORD … … -Jx
CHAPTER 1. AIRPORT PAVEMENTS - THEIR FUNCTION AND PURPOSES … 1
100. GENERAL … 1 10 1. SPECIFICATIONS AND STANDARDS … 1 102. SPECIAL CONSIDERATIONS … 2 103. STAGE CONSTRUCTION OF AIRPORT PAVEMENTS … 2
CHAPTER 1. AIRPORT PAVEMENTS - THEIR FUNCTION AND PURPOSES … 1
CHAPTER 2. SOIL INVESTIGATIONS AND EVALUATION … 3 200. GENERAL … 3 20 1. SOIL INVESTIGATIONS … 3 202. SURVEYING AND SAMPLING … 4 TABLE 2- 1. RECOMMENDED SOIL BORING SPACINGS AND
DEPTHS … 4 203. SOIL TESTS … 5 FIGURE 2- 1. TYPICAL BORING LOG … 6 204. UNIFIED SOIL CLASSIFICATION SYSTEM … 8 TABLE 2-2. CLASSIFICATION OF SOILS FOR AIRPORT PAVEMENT APPLICATIONS … 8 205. EXAMPLES … 9 FIGURE 2-2. SOIL CLASSIFICATION CRITERIA … 10 FIGURE 2-3. FLOW CHART FOR UNIFIED SOIL CLASSIFICATION SYSTEM … 11 TABLE 2-3. SOIL CHARACTERISTICS PERTINENT TO PAVEMENT FOUNDATIONS … 12 206. SOIL STRENGTH TESTS … 13 FIGURE 2-4. EFFECT OF SUBBASE ON MODULUS OF SUBGRADE REACTION … 15 207. SUBGRADE STABILIZATION … 16 208. SEASONAL FROST … 16 FIGURE 2-5. DISTRIBUTION OF DESIGN AIR FREEZING INDEXES IN THE CONTINENTAL U.S … 17 FIGURE 2-6. DISTRIBUTION OF DESIGN AIR FREEZING INDEX VALUES IN ALASKA … 18 TABLE 2-4. SOIL FROST GROUPS … 19 209. PERMAFROST … 19 FIGURE 2-7 DEPTH OF FROST PENETRATION … 20 FIGURE 2-8 RELATIONSHIP BETWEEN AIR THAWING INDEX AND THAW PENETRATION INTO GRANULAR, NON-FROST SUSCEPTIBLE SUBGRADE SOIL … 2 1
CHAPTER 3. PAVEMENT DESIGNS … 23 SECTION 1. DESIGN CONSIDERATIONS … 23 300. SCOPE … 23 30 1. DESIGN PHILOSOPHY … 23 302. BACKGROUND … 23
i
CANCELLED
AC 150/5320-6D 7r7195
303. AIRCRAFT CONSIDERATIONS … 24 304. DETERMINATION OF DESIGN AIRCRAFT … 24 305. DETERMINATION OF EQUIVALENT ANNUAL DEPARTURES BY THE DESIGN AIRCRAFT … 25 306. TRAFFIC DISTRIBUTION … 26 307. TYPICAL SECTIONS … 27 308. FROST AND PERMAFROST DESIGN … 27 FIGURE 3- 1. TYPICAL PLAN AND CROSS SECTION FOR RUNWAY PAVEMENT … 28 TABLE 3-l. REDUCED SUBGRADE STRENGTH RATINGS … 29 SECTION 2. FLEXIBLE PAVEMENT DESIGN … 31
309. GENERAL … 31 3 10. HOT MIX ASPHALT SURFACING … 31 3 11. BASE COURSE … 31 3 12. SUBBASE … 31 313. SUBGRADE … 32 TABLE 3-2. SUBGRADE COMPACTION REQUIREMENTS FOR FLEXIBLE PAVEMENTS … 33 314. SWELLING SOILS … 33 TABLE 3-3. RECOMMENDED TREATMENT OF SWELLING SOILS … 34 3 15. SELECTION OF DESIGN CBR VALUE … 34 3 16. DESIGN CURVES … 34 FIGURE 3-2. FLEXIBLE PAVEMENT DESIGN CURVES, SINGLE WHEEL GEAR … 35 FIGURE 3-3. FLEXIBLE PAVEMENT DESIGN CURVES, DUAL WHEEL GEAR … 36 FIGURE 3-4. FLEXIBLE PAVEMENT DESIGN CURVES, DUAL TANDEM GEAR … 37 FIGURE 3-5. FLEXIBLE PAVEMENT DESIGN CURVES, A-300 MODEL B2 … 38 FIGURE 3-6. FLEXIBLE PAVEMENT DESIGN CURVES, A-300 MODEL B4 … 39 FIGURE 3-7. FLEXIBLE PAVEMENT DESIGN CURVES, B-747-100, SR, 200 B, C, F … 40 FIGURE 3-8. FLEXIBLE PAVEMENT DESIGN CURVES, B-747-SP … 4 1 FIGURE 3-9. FLEXIBLE PAVEMENT DESIGN CURVES, B-757 … 42 FIGURE 3- 10. FLEXIBLE PAVEMENT DESIGN, B-767 … 43 FIGURE 3- 11. FLEXIBLE PAVEMENT DESIGN CURVES, C-130 … 44 FIGURE 3- 12. FLEXIBLE PAVEMENT DESIGN CURVES, DC lo- 10,
1OCF … 45 FIGURE 3-13. FLEXIBLE PAVEMENT DESIGN CURVES, DC 10-30, 30CF, 40,40CF … 46 FIGURE 3- 14. FLEXIBLE PAVEMENT DESIGN CURVES, L- 10 1 l- 1,
100 … 47 FIGURE 3- 15 FLEXIBLE PAVEMENT DESIGN CURVES, L-101 1, -100,200 … 48
-
CANCELLED
7r7/95 AC150/5320-61)
3 17. DESIGN INPUTS … 49 TABLE 3-4. MINIMUM BASE COURSE THICKNESS … 49 3 18. CRITICAL AND NONCRITICAL AREAS … 49 TABLE 3-5. PAVEMENT THICKNESS FOR HIGH DEPARTURE LEVELS .a...4 9 3 19. DESIGN EXAMPLE … 49 320. STABILIZED BASE AND SUBBASE … 51 321. SUBBASE AND BASE EQUIVALENCY FACTORS … 51 TABLE 3-6. RECOMMENDED EQUIVALENCY FACTOR RANGES FOR HIGH QUALITY GRANULAR SUBBASE … 52 TABLE 3-7. RECOMMENDED EQUIVALENCY FACTOR RANGES FOR STABILIZED SUBBASE … 52 TABLE 3-8. RECOMMENDED EQUIVALENCY
FACTOR RANGES FOR GRANULAR BASE … 52 TABLE 3-9. RECOMMENDED EQUIVALENCY
FACTOR RANGES FOR GRANULAR BASE … 52 TABLE 3-9. RECOMMENDED EQUIVALENCY
FACTOR RANGES FOR STABILIZED BASE … 52 322. FULL-DEPTH ASPHALT PAVEMENTS … 53 323. FROST EFFECTS … 53 SECTION 3. RIGID PAVEMENT DESIGN … 55
324. GENERAL … 55 325. CONCRETE PAVEMENT … 55 326. SUBBASE … 55 TABLE 3-10. CONDITIONS WHERE NO SUBBASE IS REQUIRED … 55 327. SUBBASE QUALITY … 55 328. STABILIZED SUBBASE … 55 329. SUBGRADE … 55 330. DETERMINATION OF FOUNDATION MODULUS (k VALUE) FOR RIGID PAVEMENT … 56 FIGURE 3-16. EFFECT OF STABILIZED SUBBASE ON SUBGRADE MODULUS … 56 33 1. DETERMINATION OF CONCRETE SLAB THICKNESS … 58 332. USE OF DESIGN CURVES … 58 333. CRITICAL AND NONCRITICAL AREAS … 58 FIGURE 3-17. RIGID PAVEMENT DESIGN CURVES, SINGLE WHEEL GEAR … 59 FIGURE 3-18. RIGID PAVEMENT DESIGN CURVES, DUAL WHEEL GEAR … 60 FIGURE 3- 19. RIGID PAVEMENT DESIGN CURVES, DUAL TANDEM GEAR … 61 FIGURE 3-20. RIGID PAVEMENT DESIGN CURVES, A-300 MODEL B2 … 6 2 FIGURE 3-21. RIGID PAVEMENT DESIGN CURVES, A-300 MODEL B4 … 6 3 FIGURE 3-22. RIGID PAVEMENT DESIGN CURVES, B-747-100, SR, 200 B, C, F … 64 FIGURE 3-23. RIGID PAVEMENT DESIGN CURVES, B-747-SP … 65 FIGURE 3-24. RIGID PAVEMENT DESIGN CURVES, B-757 … 66 FIGURE 3-25. RIGID PAVEMENT DESIGN CURVES, B-767 … 67
... 111
CANCELLED
AC 150/5320-6D 7l7l95
334. 335. 336. 337.
338. 339.
340. 341. 342. 343. 344.
FIGURE 3-26. RIGID PAVEMENT DESIGN CURVES, C- 130 … 68 FIGURE 3-27. RIGID PAVEMENT DESIGN CURVES, DC lo- 10, 1OCF … 69 FIGURE 3-28. RIGID PAVEMENT DESIGN CURVES, DC lo-30,30CF, 40,40CF … 70 FIGURE 3-29. RIGID PAVEMENT DESIGN CURVES, L-101 l-l, 100 … 71 FIGURE 3-30. RIGID PAVEMENT DESIGN CURVES, L- 10 1 l- 100,200 … 72 FIGURE 3-3 1. OPTIONAL RIGID PAVEMENT DESIGN CURVES, DUAL TANDEM GEAR … 73 FIGURE 3-32. OPTIONAL RIGID PAVEMENT DESIGN CURVES, A-300 MODEL B2 … 74 FIGURE 3-33. OPTIONAL RIGID PAVEMENT DESIGN CURVES, B-747-100, SR, 200 B, C, F … 75 FIGURE 3-34. OPTIONAL RIGID PAVEMENT DESIGN CURVES, B-747-SP … 76 FIGURE 3-35. OPTIONAL RIGID PAVEMENT DESIGN CURVES, A-300 Model B-4 … 77 FIGURE 3-36. OPTIONAL RIGID PAVEMENT DESIGN CURVES, B-757 … 78 FIGURE 3-37. OPTIONAL RIGID PAVEMENT DESIGN CURVES, B-767 … 79 FIGURE 3-38. OPTIONAL RIGID PAVEMENT DESIGN CURVES, DClO-10, 1OCF … 80 FIGURE 3-39. OPTIONAL RIGID PAVEMENT DESIGN CURVES, DC-lo-30,30CF, 40,40CF … 81 FIGURE 3-40. OPTIONAL RIGID PAVEMENT DESIGN CURVES, L-101 l-l, 100 … * … 82 FIGURE. 3-4 1. OPTIONAL PAVEMENT DESIGN CURVES, L-101 l-100,200 … 83
DESIGN EXAMPLE … I … 84 FROST EFFECTS … * … 84 HIGH TRAFFIC VOLUMES … 84 JOINTING OF CONCRETE PAVEMENTS … 85 FIGURE 3-42. RIGID PAVEMENT JOINT TYPES AND DETAILS … 86 TABLE 3- 11. RECOMMENDED MAXIMUM JOINT SPACINGS RIGID PAVEMENT WITHOUT STABILIZED SUBBASE … I.. 87
SPECIAL JOINTING CONSIDERATIONS … ‘ … 87 JOINTING STEEL … I … 88 TABLE 3- 12. DIMENSIONS AND SPACING OF STEEL DOWELS … 88
JOINT SEALANTS AND FILLERS … 88 JOINT LAYOUT … I … 88 REINFORCED CONCRETE PAVEMENT … 89 TYPE AND SPACING OF REINFORCEMENT … 89 AMOUNT OF REINFORCEMENT … 89 FIGURE 3-43. TYPICAL JOINT LAYOUT PATTERN FOR RUNWAY, PARALLEL; TAXIWAY AND CONNECTOR … 90 TABLE 3-13. YIELD STRENGTHS OF VARIOUS GRADES OF REINFORCING STEEL … 91
-
iv
CANCELLED
7l7l95 AC 150/5320-6D
TABLE 3- 14. DIMENSIONS AND UNIT WEIGHTS OF DEFORMED
TABLE 3- 14. DIMENSIONS AND UNIT WEIGHTS OF DEFORMED
STEEL REINFORCING BARS … 91 345. DIMENSIONS AND WEIGHTS OF REINFORCEMENT … 91 346. WELDED WIRE FABRIC … 91 TABLE 3-15. SECTIONAL AREAS OF WELDED FABRIC … 92 347. JOINTING OF REINFORCED PAVEMENTS … 92 FIGURE 3-44. JOINTING OF REINFORCED RIGID PAVEMENTS … 93 348. CONTINUOUSLY REINFORCED CONCRETE PAVEMENT … 94 FIGURE 3-45. CONTINUOUSLY REINFORCING CONCRETE PAVEMENT - LONGITUDINAL STEEL REINFORCEMENT … 95 349. CRCP JOINTING … 96 350. CRCP TERMINAL TREATMENT … 96 FIGURE 3-46. CONTINUOUSLY REINFORCING CONCRETE PAVEMENT - TRANSVERSE STEEL REINFORCEMENT … 97 FIGURE 3-47. CONTINUOUSLY REINFORCED CONCRETE PAVEMENT - JOINTING DETAILS … 98 FIGURE 3-48. CONTINUOUSLY REINFORCED CONCRETE PAVEMENT - WIDE FLANGE BEAM TERMINAL JOINT … 100 35 1. CRCP DESIGN EXAMPLE … 101 352. PRE STRESSED CONCRETE PAVEMENT … 102
CHAPTER 4. AIRPORT PAVEMENT OVERLAYS AND RECONSTRUCTION … lO 3
CHAPTER 4. AIRPORT PAVEMENT OVERLAYS AND RECONSTRUCTION … lO 3
400. GENERAL … 103 40 1. CONDITION OF EXISTING PAVEMENT … 103 402. MATERIAL SELECTION CONSIDERATIONS … 103 403. OVERLAY DESIGN … 103 FIGURE 4- 1. TYPICAL OVERLAY PAVEMENTS … 104 404. DESIGN OF STRUCTURAL HOT MIX ASPHALT OVERLAYS … 105 405. HOT MIX ASPHALT OVERLAYS ON EXISTING FLEXIBLE PAVEMENT … 105 406. HOT MIX ASPHALT OVERLAY ON EXISTING RIGID PAVEMENT … 106 FIGURE 4-2. ILLUSTRATION OF VARIOUS “F” FACTORS FOR HOT MIX ASPHALT OVERLAY … 107 FIGURE 4-3. GRAPH OF “F” FACTOR VS. MODULUS OF SUBGRADE REACTION FOR DIFFERENT TRAFFIC LEVELS … 108 FIGURE 4-4. ILLUSTRATION OF A “C” FACTOR OF 1.0 FOR HOT MIX ASPHALT OVERLAY DESIGN … 109 FIGURE 4-5. ILLUSTRATION OF A “C” FACTOR OF 0.75 FOR HOT MIX ASPHALT OVERLAY DESIGN … 110 407. NON STRUCTURAL HOT MIX ASPHALT OVERLAYS … 112 408. REFLECTION CRACKING IN HOT MIX ASPHALT OVERLAYS … 112 409. DESIGN OF CONCRETE OVERLAYS … 112 410. CONCRETE OVERLAY ON FLEXIBLE PAVEMENT … 112 4 11. CONCRETE OVERLAY ON RIGID PAVEMENT … 113 412. BONDED CONCRETE OVERLAYS … 114 413. JOINTING OF CONCRETE OVERLAYS … 114
V
CANCELLED
AC 150/5320-6D 7l7195
FIGURE 4-6. ILLUSTRATION OF A “Cr.” FACTOR OR 1.0 … 115 FIGURE 4-7. ILLUSTRATION OF A “C” FACTOR OF 0.6 … 116 FIGURE 4-8. ILLUSTRATION OF A “C” FACTOR OF 0.35 … 117 FIGURE 4-9. CONCRETE OVERLAY ON RIGID PAVEMENT … 118 FIGURE 4- 10. CONCRETE OVERLAY ON RIGID PAVEMENT … 119 FIGURE 4- 11. CONCRETE OVERLAY ON RIGID PAVEMENT WITH LEVELING COURSE … f … 120 FIGURE 4-12. CONCRETE OVERLAY ON RIGID PAVEMENT WITH LEVELING COURSE … f … 121 4 14. PREPARATION OF THE EXISTING SURFACE FOR THE OVERLAY … 122 4 15. MATERIALS AND METHODS … , … 123 416. NEW OVERLAY MATERIALS … 123 4 17. POSSIBLE ANOMALIES … 124
CHAPTER 5. PAVEMENTS FOR LIGHT AIRCRAFT … 125
CHAPTER 5. PAVEMENTS FOR LIGHT AIRCRAFT … 125
500. GENERAL … 125 501. TYPICAL SECTIONS … 125 502. FLEXIBLE PAVEMENT MATERIALS … 125 FIGURE 5- 1. TYPICAL SECTIONS FOR LIGHT AIRCRAFT PAVEMENTS … 126 TABLE 5-l. SUBGRADE COMPACTION REQUIREMENTS FOR LIGHT LOAD FLEXIBLE PAVEMENTS … 127 503. FLEXIBLE PAVEMENT DESIGN … 127 FIGURE 5-2. DESIGN CURVES FOR FLEXIBLE PAVEMENTS - LIGHT AIRCRAFT … 128 504. RIGID PAVEMENT MATERIALS … 129 505. RIGID PAVEMENT THICKNESS … 130 506. AGGREGATE TURF … 130 507. OVERLAYS … 130 FIGURE 5-3. JOINTING DETAIL FOR LIGHT LOAD RIGID PAVEMENTS … 131 FIGURE 5-4. CON’T JOINTING DETAILS FOR LIGHT LOAD RIGID PAVEMENTS … 131 FIGURE 5-5. JOINT LAYOUT PATTERNS FOR LIGHT LOAD RIGID PAVEMENTS - 60 FEET WIDE … 133 FIGURE 5-6. JOINT LAYOUT PATTERNS FOR LIGHT LOAD RIGID PAVEMENTS - 50 FEET WIDE … 134
CHAPTER 6. PAVEMENT EVALUATION … 135
CHAPTER 6. PAVEMENT EVALUATION … 135
600. PURPOSES OF PAVEMENT EVALUATION … 135 60 1. EVALUATION PROCESS … 135 602. FLEXIBLE PAVEMENTS … 136 FIGURE 6- 1. CBR - FAA SUBGRADE CLASS COMPARISONS … 137 603. APPLICATION OF FLEXIBLE PAVEMENT EVALUATION PROCEDURES … 137 604. RIGID PAVEMENTS … 138
vi
-
CANCELLED
7/7/95 AC 150/5320-6D
605. APPLICATION OF RIGID PAVEMENT EVALUATION PROCEDURES … 139 606. USE OF RESULTS … 139 607. REPORTING PAVEMENT STRENGTH … 139
APPENDIX 1. ECONOMIC ANALYSIS … 1
APPENDIX 1. ECONOMIC ANALYSIS … 1
1. BACKGROUND … 1 2. ANALYSIS METHOD … 1 3. STEP BY STEP PROCEDURE … 1 4. EXAMPLE PROBLEM - LIGHT-LOAD GENERAL AVIATION AIRPORT … 2 TABLE 1. COSTS OF REHABILITATION ACTIVITIES … 3 TABLE 2. PRESENT WORTH LIFE-CYCLE COSTING … 4 TABLE 3. SUMMARY OF ALTERNATIVES … 5 TABLE 4. COMPARATIVE RANKING OF ALTERNATIVES … 5 5. SUMMARY … 5
APPENDIX 2. DEVELOPMENT OF PAVEMENT DESIGN CURVES … 1
APPENDIX 2. DEVELOPMENT OF PAVEMENT DESIGN CURVES … 1
1. BACKGROUND … 1 TABLE 1. SINGLE WHEEL ASSEMBLY … 1 TABLE 2. DUAL WHEEL ASSEMBLY … 1 TABLE 3. DUAL TANDEM ASSEMBLY … 1 2. RIGID PAVEMENTS … 1 TABLE 4. PASS-TO-COVERAGE RATIOS FOR RIGID PAVEMENTS … 2 FIGURE 1. ASSEMBLY POSITIONS FOR RIGID PAVEMENT ANALYSIS … 3 FIGURE 2. PERCENT THICKNESS VS. COVERAGES … 4 3. FLEXIBLE PAVEMENTS … 5 TABLE 5. PASS-TO-COVERAGE RATIOS FOR FLEXIBLE PAVEMENTS … 5 FIGURE 3. LOAD REPETITION FACTOR VS. COVERAGES … we.6
APPENDIX 3. DESIGN OF STRUCTURES FOR HEAVY AIRCRAFT … 1
APPENDIX 3. DESIGN OF STRUCTURES FOR HEAVY AIRCRAFT … 1
1. BACKGROUND … 1 2. RECOMMENDED DESIGN PARAMETERS … 1 FIGURE 1. TYPICAL GEAR CONFIGURATIONS FOR DESIGN OF STRUCTURES … 2
APPENDIX 4. RELATED READING MATERIAL … ~ … 1
vii and (ix)
CANCELLED
717195 AC 150/532&6D
FOREWORD
This advisory circular is intended to provide guidance on the structural design and evaluation of airport pavements.
APPENDIX 4. RELATED READING MATERIAL … ~ … 1
Although aircraft landing gears are involved in airport pavement design and evaluation, this circular is not intended to dictate any facet of landing gear design. In 1958, the FAA adopted a policy of limiting maximum Federal participation in airport pavements to a pavement section designed to serve a 350,000-pound (159 000 kg) aircraft with a DC-S-50 series landing gear configuration. In addition, the intent of the policy was to insure that future aircraft were equipped with lauding gears which would not stress Pavements more than the referenced 350,000-pound (159 000 kg) aircraft.
Aircraft manufacturers have accepted and followed the 1958 policy and have designed aircraft landing gear which conform to the policy even though aircraft gross weights have substantially exceeded 350,000 pounds (159 000 kg). This has been accomplished by increasing the number and spacing of landing gear wheels. This circular does not affect the 1958 policy with regard to landing gear design.
The pavement design guidance presented in Chapter 3 of this circular is based on methods of analysis which have resulted from experience and recent research. The change in methods was adopted to exploit these advances in pavement technology and thus provides better performing pavements and easier-to-use design curves. Generally speaking, the new design guidance will require somewhat thicker pavement sections than were required in the past.
The pavement evaluation portion of this circular is presented in Chapter 6 and is related back to the previous FAA method of design to insure continuity. An aircraft operator could be penalized unfairly if an existing facility were evaluated using a method different from that employed in the original design. A slight change in pavement thickness can have a dramatic effect on the payload or range of an aircraft. Since the new pavement design methodology generally requires slightly greater pavement thicknesses, an evaluation of an existing pavement using the new methodology would likely reduce allowable loads and penalize operators. To avoid this situation the evaluation should be based on the same methodology as was used for design.
ix
CANCELLED
7l7l95 AC 150/5320-6D
CHAPTER 1. AIRPORT PAVEMENTS -THEIR FUNCTION AND PURPOSES
CHAPTER 1. AIRPORT PAVEMENTS -THEIR FUNCTION AND PURPOSES
100. GENERAL. Airport pavements are constructed to provide adequate support for the loads imposed by aircraft using an airport and to produce a firm, stable, smooth, all-year, all-weather surface free from dust or other particles that may be blown or picked up by propeller wash or jet blast. In order to satisfactorily fulfill these requirements, the pavement must be of such quality and thickness that it will not fail under the load imposed. In addition, it must possess sufficient inherent stability to withstand, without damage, the abrasive action of traffic, adverse weather conditions, and other deteriorating influences. To produce such pavements requires a coordination of many factors of design, construction, and inspection to assure the best possible combination of available materials and a high standard of workmanship.
a. Types of Pavement. Pavements discussed in this circular are flexible, rigid, hot mix asphalt overlays, and rigid overlays. Various combinations of pavement types and stabilized layers can result in complex pavements which would be classified in between flexible and rigid. The design and evaluation guidance in this circular can be adapted to any pavement type.
b. Economic Analysis and Design Selection. When properly designed and constructed, any pavement type (rigid, flexible, composite, etc.) can provide a satisfactory pavement for any civil aircraft. However, some designs may be more economical than others and still provide satisfactory performance. The engineer is required to provide a rationale for the selected design in the engineer’s report (see AC 150/5300-9). Often this rationale will be based on economic factors derived from evaluating several design alternatives. Life-cycle cost analysis should be used if the design selection is based on least cost. An example of a life-cycle cost analysis of alternatives for pavement rehabilitation is shown in Appendix 1. More details on life-cycle cost analysis can be found in research report DOT/FAA&D-81/78 (see Appendix 4). Many new developments in construction have evolved in recent times which can significantly affect pavement costs, such as, recycling. In instances where no clear cost advantage can be established in the design process, alternate bids should be taken. Design selection is not always controlled by economic factors. Operational constraints, funding limitations, future expansion, etc., can override economic factors in the design selection. These considerations should be addressed in the engineer’s report.
C. Pavement Courses.
(1) Surface. Surface courses include portland cement concrete, hot mix asphalt, sand-bituminous mixture, and sprayed bituminous surface treatments.
(2) Base. Base courses consist of a variety of different materials which generally fall into two main classes, treated and untreated. The untreated bases consist of crushed or uncrushed aggregates. The treated bases normally consist of a crushed or uncrushed aggregate that has been mixed with a stabilizer such as cement, bitumen, etc.
(3) Subbase. Subbase courses consist of a granular material, a stabilized granular material, or a stabilized soil.
(4) Geotextile. Geotextiles are permeable, flexible, textile materials sometimes used to provide separation between pavement aggregate and the underlying subgrade. Geotextile needs and requirements within a pavement section are dependent upon subgrade soil and groundwater conditions and on the type of overlying pavement aggregate.
101. SPECIFICATIONS AND STANDARDS.
a. Specifications. Reference is made by Item Number throughout the text to construction material specifications contained in AC 150/5370-10, Standards for Specifying Construction of Airports.
b. Geometric Standards. Geometric standards concerning pavement lengths, widths, grades, and slopes
CANCELLED
AC 150/5320-61) 7/7/95
are presented in advisory circulars listed in Appendix 4.
102. SPECIAL CONSIDERATIONS. Airport pavements should provide a surface which is not slippery and will provide good traction during any weather conditions. AC 150/5320-12, Measurement, Construction and Maintenance of Skid Resistant Airport Pavement Surfaces, presents information on skid resistant surfaces.
103. STAGE CONSTRUCTION OF AIRPORT PAVEMENTS. In some instances it may be necessary to construct the airport pavement in stages; that is, to build up the pavement profile, layer by layer, as the traffic using the facility increases in weight and number. Lateral staging, i.e., planning for future widening of pavements is sometimes advantageous to accommodate larger aircraft. If stage construction is to be undertaken, the need for sound planning cannot be overemphasized. The complete pavement should be designed prior to the start of any stage, and each stage must provide an operational surface. The planning of a stage constructed pavement should recognize a number of considerations.
a. Economics. Careful economic studies are required to determine if staged construction is warranted. Construction materials and labor costs follow inflationary trends and can be expected to increased as later stages are constructed. The costs and time involved in any pavement shutdown or diversion of traffic necessitated by the construction of any stage should be considered. The costs of mobilizing construction equipment several times should be compared with mobilizing once. The costs of maintaining an intermediate stage should be considered.
b. Adequacy of Each Stage. Each stage should be designed to adequately accommodate the traffic which will use the pavement until the next stage is constructed.
C. Drainage. The underlying layers and drainage facilities of a stage constructed pavement should be built to the standards required for the final cross section. Providing the proper foundation and drainage facilities in the first stage is mandatory as the underlying layers will not be readily accessible for upgrading in the future.
d. Communication. All parties concerned and, insofar as practicable, the general public should be informed that staged construction is planned. Staged construction sometimes draws unjust criticism when relatively new facilities are upgraded for the next stage.
CANCELLED
717195 AC 150/5320-6D
CHAPTER 2. SOIL INVESTIGATIONS AND EVALUATION
CHAPTER 2. SOIL INVESTIGATIONS AND EVALUATION
200. GENERAL. The importance of accurate identification and evaluation of pavement foundations cannot be overemphasized. Although it is impossible to explore the entire field of soil mechanics in a publication such as this, the following text will highlight those aspects which are particularly important to the airport paving engineer.
a. Classification System. The Unified Soil Classification (USC) system should be used in engineering matters concerning civil airport pavements. To avoid misunderstanding, certain terms employed are defined below:
(1) Definition. For engineering purposes, and particularly as it applies to airports, soil includes all natural deposits which can be moved with earth moving equipment, without requiring blasting under unfrozen conditions. Harder materials are considered to be rock.
(2) Conditions and Properties. Soil conditions include such items as the elevation of the water table, the presence of water bearing strata, and the field properties of the soil. Field properties of the soil include the soil’s density, moisture content, and frost penetration.
(3) Profile. The soil profile is the vertical arrangement of layers of soils, each of which possesses different physical properties from the adjacent layer.
(4) Subgrade. Subgrade soil is that soil which forms the foundation for the pavement. It is the soil directly beneath the pavement structure.
b. Costs. Soil conditions and the local prices of suitable construction materials are important items affecting the cost of construction of airport pavements. Earthwork and grading costs are directly related to the difficulty with which excavation can be accomplished and compaction obtained.
C. Subgrade Support. It should be remembered that the subgrade soil ultimately provides support for the pavement and the imposed loads. The pavement serves to distribute the imposed load to the subgrade over an area greater than that of the tire contact area. The greater the thickness of pavement, the greater is the area over which the load on the subgrade is distributed. It follows, therefore, that the more unstable the subgrade soil, the greater is the required area of load distribution and consequently the greater is the required thickness of pavement. The soils having the best engineering characteristics encountered in the grading and excavating operations should be incorporated in the upper layers of the subgrade by selective grading if economically feasible.
d. Drainage. In addition to the relationship which soil conditions bear to grading and paving operations, they determine the necessity for underdrains and materially influence the amount of surface runoff. Thus, they have a resulting effect on the size and extent of other drainage structures and facilities. (See FAA publication, AC 150/5320-5, Airport Drainage.)
201. SOIL INVESTIGATIONS.
a. Distribution and Properties. To provide essential information on the various types of soils, investigations should be made to determine their distribution and physical properties. This information combined with data on site topography and area climatic records, provides basic planning material essential to the logical and effective development of the airport. An investigation of soil conditions at an airport site will include:
(1) Survey. A soil survey to determine the arrangement of different layers of the soil profile with relation to the proposed subgrade elevation.
(2) Sampling. Collection of representative samples of the layers of soil.
(3) Testing. Testing of samples to determine the physical properties of the various soil materials with respect to in-place density and subgrade support.
CANCELLED
AC 150/5320-6D 7m95
(4) Availability. A survey to determine the availability of materials for use in construction of the subgrade and pavement.
b. Procedures. With respect to sampling and surveying procedures and techniques, ASTM D 420, Investigating and Sampling Soils and Rock for Engineering Purposes, is one of the most frequently used. This method is based entirely on the soil profile. In the field, ASTM D 2488, Description of Soils (Visual-Manual Procedures) is commonly used to identify soils by such characteristics as color, texture, structure, consistency, compactness, cementation, and to varying degrees, chemical composition.
(1) Maps. The use of Department of Agriculture soils maps, United States Geodetic Survey (USGS) geologic maps, and USGS engineering geology maps can prove valuable aids in the study of soils at and in the vicinity of the airport. Although the pedological classification, determined from these maps, does not treat soil as an engineering or construction material, data so obtained are extremely useful to the agronomist in connection with the development of turf areas on airports and to the engineer concerned with preliminary investigations of site selection, development costs, and alignment.
(2) Aerial Photography. The practice of determining data on soils by use of aerial photographs is established and commonly acceptable. Relief, drainage, and soil patterns may be determined from the photographs, and an experienced photo interpreter can define differences in characteristics of soils. By employing this method of investigation, it is possible to expedite soil studies and reduce the amount of effort required to gather data.
202. SURVEYING AND SAMPLING.
a. Soil Borings. The initial step in an investigation of soil conditions is a soil survey to determine the quantity and extent of the different types of soil, the arrangement of soil layers, and the depth of any subsurface water. These profile borings are usually obtained with a soil auger or similar device. Washed borings are not recommended due to inaccuracies of depth determinations. The intent of the borings is to determine the soil or rock profile and its lateral extent. Inasmuch as each location presents its particular problems and variations, the spacing of borings cannot always be definitely specified by rule or preconceived plan. Suggested criteria for the location, depth, and number of borings are given in Table 2-1. Wide variations in these criteria can be expected due to local conditions.
TABLE 2-1. RECOMMENDED SOIL BORING SPACINGS AND DEPTHS AREA SPACING DEPTH Runways and Taxiways Random across pavement at 200 Cut Areas - 10’ (3.5 m) Below foot (68 m) intervals Finished Grade Fill Areas - 10’ (3.5 m) Below Existing Ground’ Other Areas of Pavement 1 Boring per 10,000 Square Feet Cut Areas - 10’ (3.5 m) Below (930 sq m) of Area Finished Grade Fill Areas - 10’ (3.5 m) Below Existing Ground’ Borrow Areas Sufficient Tests to Clearly Define To Depth of Borrow Excavation the Borrow Material ‘For deep fills, boring depths shall be sufficient to determine the extent of consolidation and/or slippage the fill may cause.
b. Number of Borings, Locations, and Depths. Obviously, the locations, depths, and numbers of borings must be such that all important soil variations can be determined and mapped. Whenever past experience at the location in question has indicated that settlement or stability in deep fill areas may be a problem or, if in the opinion of the engineer, additional investigations are warranted, more or deeper borings may be required in order that the proper design, location, and construction procedures may be determined. Cdnversely, where uniform soil conditions are encountered, fewer borings may be acceptable.
CANCELLED
7l7l95 AC150/5320-6D
C. Boring Log. A graphic log of soil conditions can be of great value in assessing subgrade conditions. It is recommended that the graphic log be developed which summarizes the results of the soil explorations. A typical graphic log is included as Figure 2-1. The graphic log should include:
(1) Location
(2) Date Performed
(3) Type of exploration
(4) Surface elevation
(5) Depth of materials
(6) Sample identification numbers
(7) Classification
(8) Water table
d. Soil Survey Areas. The soil survey is not confined to soils encountered in grading or necessarily to the area within the boundaries of the airport site. Possible sources of locally available material that may be used as borrow areas or aggregate sources should be investigated.
e. Undisturbed Samples. Samples representative of the different layers of the various soils encountered and various construction material discovered should be obtained and tested in the laboratory to determine their physical and engineering properties. In-situ properties such as in-place density, shear strength, consolidation characteristics, etc. may necessitate obtaining “undisturbed” core samples. ASTM D 1587, Thin Walled Tube Sampling of Soils, describes a method of obtaining “undisturbed” soil samples. Because the results of a test can only be as good as the sampling, it is of utmost importance that each sample be representative of a particular type of soil material and not be a careless and indiscriminate mixture of several materials.
f. Inplace Testing. Pits, open cuts, or both may be required for making inplace bearing tests, for the taking of undisturbed samples, for charting variable soil strata, etc. This type of supplemental soil investigation is recommended for situations which warrant a high degree of accuracy or when in situ conditions are complex and require extensive investigation,
203. SOIL TESTS.
a. Physical Soil Properties. To determine the physical properties of a soil and to provide an estimate of its behavior under various conditions, it is necessary to conduct certain soil tests. A number of field and laboratory tests have been developed and standardized. Detailed methods of pet forming soil tests are completely covered in publications of the American Society for Testing and Materials (ASTM).
b. Testing Requirements. Soil tests are usually identified by terms indicating the soil characteristics which the tests will reveal. Terms which identify the tests considered to be the minimum or basic requirement for airport pavement, with their ASTM designations and brief explanations, follow:
CANCELLED
AC 150/5320-6D 7m95
STATION 68 6 9 7 0 71 7 2
BORING NUMBER 31 3 2 3 3
ELEVATION
LEGEND 0 BORING @i FI-FJE S A N D , S P
m T O P S O I L m HEAVY BROWN CLAY, CH
q SANDY CLAY,SC P WATER TABLE
NOTE: ALL SAMPLES OBTAINED WITH SPLIT BARREL TECHNIQUES
FIGURE 2-1 TYPICAL BORING LOG
CANCELLED
FIGURE 2-1 TYPICAL BORING LOG
7r7l95 AC 150/5320-6D
(1) Dry Preparation of Soil Samples for Particle-Size Analysis and Determination of Soil Constants (ASTM D 421) or Wet Preparation of Soil Samples for Grain-Size Analysis and Determination of Soil
Constants (ASTM D 2217). The dry method (D-421) should be used only for clean, cohesionless granular materials.
The wet method (D-2217) should be used for all cohesive or borderline materials. In case of doubt, the wet method
should be used.
(2) Particle-Size Analysis of Soils (ASTM C 422). This analysis provides a quantitative determination of the distribution of particle sizes in soils.
(3) Liquid Limit, Plastic Limit and Plasticity Index of Soils (ASTM D 4318). The plastic and liquid limits of soil define in a standard manner the lowest moisture contents at which a soil will change from a semisolid to a plastic state and at which a solid passes from a plastic to a liquid state, respectively. The plasticity index is the numerical difference between the plastic limit and the liquid limit. It indicates the range in moisture content over which a soil remains in a plastic state prior to changing into a liquid. The plastic limit, liquid limit and plasticity index of soils are used in engineering classification in accordance with the Unified Soil Classification System (ASTM D 2487). In conjunction with particle size analysis, natural moisture content and other soil properties or conditions, the limits may be used to estimate engineering properties or behavior of soils such as shrink/swell potential, consolidation characteristics, construction/stabilization characteristics, permeability, and strength characteristics.
(4) Moisture-Density Relations of Soils (ASTM D 698, D 1557). For purposes of compaction control during construction, tests to determine the moisture-density relations of the different types of soils should be performed.
(0 Heavy Load Pavements. For pavements designed to serve aircraft weighing 30,000 pounds (13 000 kg) or more, use ASTM Method D 1557.
(ii) Light Load Pavements. For pavements designed to serve aircraft weighing less than 30,000 pounds (13 000 kg), use ASTM Method D 698.
(5) Bearing Ratio of Laboratory-Compacted Soils (ASTM D 1883). This test is used to assign a California Bearing Ratio (CBR) value to subgrade soils for use in the design of flexible pavements.
(6) Modulus of Soil Reaction (AASHTO T 222). This test is used to determine the modulus of soil reaction, K, for use in the design of rigid pavements.
C. Supplemental Tests. In many cases additional soil tests will be required over those listed in paragraph 203b above. It is not possible to cover all the additional tests which may be required; however, a few examples are presented below. This list should not be considered all inclusive.
(1) Shrinkage Factors of Soils (ASTM D 427). This test may be required in areas where swelling soils might be encountered.
(2) Permeability of Granular Soils (ASTM D 2434). This test may be needed to assist in the design of subsurface drainage.
(3) Determination of Organic Material in Soils by Wet Combustion (AASHTO T-194). This test may be needed in areas where deep pockets of organic material are encountered or suspected.
(4) California Bearing Ratio, Field In-place Tests (Mil-Std 621, Method 101). Field bearing tests can be performed when the in site conditions satisfy density and moisture conditions which will exist under the pavement being designed. The method is also described in Manual Series No. 10, Soils Manual, The Asphalt Institute, College Park, MD.
CANCELLED
AC 150/5320-6D 7m95
204. UNIFIED SOIL CLASSIFICATION SYSTEM.
a. Purpose. The standard method of classifying soils for engineering purposes is ASTM D 2487, commonly called the Unified system. The primary purpose in determining the soil classification is to enable the engineer to predict probable field behavior of soils. The soil constants in themselves also provide some guidance on which to base performance predictions. The Unified system classifies soils first on the basis of grain size, then further subgroups soils on the plasticity constants. Table 2-2 presents the classification of soils by the Unified system.
b. Initial Division. As indicated in Table 2-2, the initial division of soils is based on the separation of coarse-and fine-grained soils and highly organic soils. The distinction between coarse and fine grained is determined by the amount of material retained on the No. 200 sieve. Coarse-grained soils are further subdivided into gravels and sands on the basis of the amount of material retained on the No. 4 sieve. Gravels and sands are then classed according to whether or not fine material is present. Fine-grained soils are subdivided into two groups on the basis of liquid limit. A separate division of highly organic soils is established for materials which are not generally suitable for construction purposes.
TABLE 2-2. CLASSIFICATION OF SOILS FOR AIRPORT PAVEMENT APPLICATIONS
TABLE 2-2. CLASSIFICATION OF SOILS FOR AIRPORT PAVEMENT APPLICATIONS
MAJOR DIVISIONS GROUP SYMBOLS Coarse-grained Soils more 1 Gravels 50% or more of coarse fraction I Clean I GW than 50% retained on No. 200 sieve’ retained on No. 4 sieve
Fine-grained Soils 50 % or less retained on No. 200 sieve’
Fines CC Sands less than 50% of coarse fraction retained Clean SW on No. 4 sieve Sands SP Sands with SM Fines SC Silts and Clays Liquid Limit 50% or less ML CL OL
Silts and Clays Liquid Limit Greater than 50% MH CH OH
Highly Organic Soils ‘Based on the material passing the 3-in (75-mm) sieve.
PT
C. Soil Groups. Soils are further subdivided into 15 different groupings. The group symbols and a brief description of each is given below:
(1) GW (2) GP
(3) GM
(4) GC
(5) SW (6) SP
(7) SM
(8) SC
(9) ML WV CL
(9) ML WV CL
(11) OL (12) MH
Well-graded gravels and gravel-sand mixtures, little or no fines. Poorly graded gravels and gravel-sand mixtures, little or no fines. Silty gravels, gravel-sand-silt mixtures. Clayey gravels, gravel-sand-clay mixtures. Well-graded sands and gravelly sands, little or no fines. Poorly graded sands and gravelly sands, little or no tines. Silty sands, sand-silt mixtures. Clayey sands, sand-clay mixtures. Inorganic silts, very fine sands, rock flour, silty or clayey fine sands. Inorganic clays of low to medium plasticity, gravelly clays, silty clays, lean clays. Organic si!:s and organic silty clays of low plasticity. Inorganic silts, micaceous or diatomaceous fine sands or silts, plastic silts.
CANCELLED
7/7/95 AC 150/5320-6D
(13) CH Inorganic clays or high plasticity, fat clays. (14) OH Organic clays of medium to high plasticity. (15) PT Peat, muck and other highly organic soils.
d. Final Classification. Determination of the final classification group requires other criteria in addition to that given in Table 2-2. These additional criteria are presented in Figure 2-2 and have application to both coarse and tine grained soils.
e. Flow Chart. A flow chart which outlines the soil classification process has been developed and is included as Figure 2-3. This flow chart indicates the steps necessary to classify soils in accordance with ASTM D 2487.
f. Field Identification. ASTM D 2488, Description of Soils (Visual-Manual Procedure), presents a simple, rapid method of field identification of soils. This procedure provides techniques for classifying soils rather accurately with a minimum of time and equipment.
g. Characteristics as Pavement Foundations. A table of pertinent characteristics of soils used for pavement foundations is presented in Table 2-3. These characteristics are to be considered as approximate, and the values listed are generalizations which should not be used in lieu of testing.
205. EXAMPLES. The following examples illustrate the classification of soils by the Unified system. The classification process progresses through the flow chart shown in Figure 2-3.
a. Example 1. Assume a soil sample has the following properties and is to be classified in accordance with the Unified system.
(1) Fines. Percent passing No. 200 sieve = 98%.
\ (2) Liquid Limit. Liquid limit on minus 40 material 30%.
(3) Plastic Limit. Plastic limit on minus 40 material 10%.
(4) Plasticity Chart. Above “A” line, see Figure 2-2. The soil would be classified as CL, lean clay of low to medium plasticity. Table 2-3 indicates the material would be of fair to poor value as a foundation when not subject to frost action. The potential for frost action is medium to high.
b. Example 2. Assume a soil sample with the following properties is to be classified by the Unified system.
(1) Fines. Percent passing No. 200 sieve = 48%.
CANCELLED
AC 15015320-61) 7m95
CLASSIFICATION CRITERIA
CLASSIFICATION CRITERIA
C I
u = D60/DJD G r e a t e r t h a n 4
3 n z (D30) 2
E -ii WI ‘z = D JO x ‘60
Between 1 and 3
E o,LE
% “E ix-m v1 gy,*= Not meeting both criteria for GU .- - - ..- m +.a.;;~
:: ..TL L 3 x 0 0 Atterberg I imits plot below “A” J inc Atterberg limits plotting
x *om
or plasticity index less than 4 in hatched area are : * borderline classifications *oaf = Atterberg limits plot above “A” line requiring use of dual >U r u .- ,” and blasticity index greater than 7 symbols
r
‘; Y( f .; ,
ou- c 0 oo- 3 ON Y) u ” = D60/DJo Greater.thrn 6 6” -0 2 (D3D)2 5 +E cZ= D 0 ; VI ..- 10 ’ ‘60 Getween I and 3
Z,“ro’ : roe
; ;lz 2 Not meeting both criteria for SW -2
s S E c 11L- Atterberg I imi ts plot below “A” line Atterberg limits plotting YY or plasticity index less than 4 i n h a t c h e d a r e a a r e ;:‘o borderline classifications
SS% Atterberg I imi ts plot above “A” I ine requiring use of dual and plasticity index greater than 7 symbol 5
FIGURE 2-2 SOIL CLASSIFICATION CRITERIA
FIGURE 2-2 SOIL CLASSIFICATION CRITERIA
CANCELLED
Make vrsual ertmrnrtion of sod to determine whether 4 IS hghly org~mc, CoarW gUmed, or fmc gramed. In bordcr- Irne cases determine Jmount pJssmg No. 200 sreve
r
1 I 1 IllnrGllinrdI
More lhan 50% oass No. 200 SIWC. I
Highly Organrc sailt
1 I 1 IllnrGllinrdI
ml
Coarse Crrmed
Fibrous texture, cdor, odor, very
50% or less pass No. 200 sieve.
1 1
high morsture content, p~rWcs of vegetable matter (stick, IeJues, etc.)
1 Run 11 and FL on mmus 40 srcve materral 1
1 mtJmldbl:lZY: sieve 1 1 pJS.Zi;:I:,, 1 Greater percentrgc of cwrse fraction CreJler percentage of coarse fraction phi ;,;;;;;;Jrt ;plz;:.;.
1 Run 11 and FL on mmus 40 srcve materral 1
plastrcrty chart PlJstlcity Chart P!JStlCltY chart
LL and PL on oven
I
1 r 1 3c
Inorganrc OrgJnw
Borderhne. to
hrve double symbol Jpproprralei
to grading Jnd
PtJStlCity ChJrJC-
terrstrcs, e.g., SW-SM
I
I ExJmine ;T’,;;;;;ny- Run LL Jld
gram-size to grading md on minus
curw plJWity ChUJc- No. 40 sieve
teristrcs, e.g., frJctron
CW-CM 1
Color, odor. possrbly
IL Jnd PL on oven
dry sod
OrgJnrc@!
Inorganic
1 01 ML ML-CL
1 01 ML ML-CL
I I I I ~~~~
plrsticity chJrt plJstrcrty chart PkllClty chart
Note: Sieve sizes are U.S. Standard.
l If frnet interlere wrth free-dnining properties use double symbol such u GW-GM, rtc
Figure 213. Flow chart for Unified Soil Classification System
CANCELLED
TABLE 2-3. Soil Characteristics Pertinent to Pavement Foundations
hklJ0' b'lSlOIlS Letter Name
Value as Foundation When
Not Subject to
Frost Action
Value as
Base Directly
under Wearing
Surface
Potential Frost Action
Compressi-
bility and Expanston
Dramage Characteristics Compaction Equipment
Unit Dry
Weight
(pcfl
Freld CUR
Subgrade Modulus k
(pci) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13)
(iW Gravel or sandy gravel. Excellent Good None to very Ahnost none Excellent Crawler-type tractor. 125-140 60-80 300 or more
t‘onrse-
gramcd
(iI’
well graded
< irwcl
p"'1 ly
or saiitly g1;&d
gravel,
Gravel and
gral ell)
soils
GU
titv1
Gravel or sandy gravel, nmformfy graded
Silty glilvd 01 Silty S;llllly
g1 avcl
(iC Clayey gravel sandy gravel
or clayey
slight
Figure 213 · page 20Picture of the page from the copy saved here
<ku~cl to excellent Poor to fair None to very hilllost none slight
Good Poor None to very Almost none slight
(kxxl to cxcellcllt Fair to good slight t0 Very slight medium
Good Poor Slight to
medium
Slight
rubber-tired equipment.
steel-wheeled roller
Ilxcellcnt Crawler-type Iraclor. 120-130 35-60 300 or more rubber-tired equipment.
steel-wheeled roller
Excellent Crawler-type tractor, 115-125 25-50 300 or more rubber-tired equipment
Fair to poor Rubber-tired equipmeut, 130-145 40-mo 3tJtJ or mote sheepsfoot roller, close
conIrol of moisture
Poor to practi- Rubber-tired equipment, 120-140 20-40 200-300 tally impervious sheepsfoo1 roller Wllb
SW Sand or gravelly sand, Good Poor None to very Almost noue Excellent Crawler-type tractor. I IO-130 20-40 200-300 well graded slight rubber-tired equipmeut
SI’ Sand or gravelly sand. poorly graded
Fair to good Poor 10 not None to very suitable slight
Almost none . Excellent Crawler-type tractor. rubber-tired equipment
105-120 15-25 200-300
Sand and sandy soils
SIJ
SM
Sand or gravelly sand, uniformly graded
Silty sriitl or silty gravelly sand
Farr to good
Good
Not suitable None to very Almost none Excellent Crawler-type tractor, 100-115 IO-20 200-300 slight rubber-tired equipment
Poor Sliglit to high Very slight Fair to poor Rubber-tired equipment, 120-135 20-40 200-300 sheepsfoot roller. close
coutrol of moisture
SC Clayey sand or clayey Fau to good Not suitable Slight to high Slight IO Poor to practi- Rubber-tired quipment. 105-130 JO-20 200-300
Fine-
Low compressi-
bility LL < 50
M L
CL
01,
gravelly sand
Silts, sandy silts, gravelly stlts, or diatomaceous soils
Lean clays, sandy clays, or gravelly clays
Organic silts or lean
Fair to good
Fau to good
Poor
Not suitable
Not suitable
Not suitable
Medium to
very high
Medium to
high
Medium to
medium tally impervious sheepsfoot roller
Slight to Fair to poor Rubber-tired equipment, 100-125 5-15 IOO-200 medium skepsfoot roller, close
control of moisture
Medium Practically Rubber-tired equipment, It-IO-125 5-15 100-200 impervious sheepsfoot roller
Medium to Poor Rubber-tired quipmeut. 90-105 4-8 IOO-200
gramed
Soils
organic clays high high sheepsfoot roller
Ml1 Micaceous clays or Poor Not suitable Medium to ffigh Fair to poor Rubber-tired quipment, 80- IO0 4-g IOO-200
Ilieb diatomaceous soils very high sheepsfoot roller -- D compressi-
bthty
CII Fat clays Poor to very poor Not suitable Medium ffigh Practically Rubber-tired equipment. 90-I IO 3-5 50-100 impervious sheepsfoot roller
LL > 50 011 Fat orgamc clays Poor to very poor Not suitable Medium Ifigh Practically Rubber-tired quipmeut, SO-105 3-5 50-100
Peat and other librous Pt Peat, humus and other Not suitable Not suitable Slight Very high
impervious
Fair to poor
sheepsfoot roller
Compaction not practical
organic soils
CANCELLED
7l7i95 AC150/5320-6D
(2) Gravel. Percent of coarse fraction retained on No. 4 sieve = 70%.
(3) Liquid Limit. Liquid limit on minus 40 fraction = 60%.
(4) Plastic Limit. Plastic limit on minus 40 fraction = 20%.
(5) Plasticity Index. Compute Plasticity Index LL-PL = 40%.
(6) Plasticity Chart. Above “A” line, see Figure 2-2.
(7) Classification. This sample is classified as CC, clayey gravel. Table 2-3 indicates the material is good for use as a pavement foundation when not subject to frost action. The potential for frost action is slight to medium.
206. SOIL STRENGTH TESTS. Soil classification for engineering purposes provides an indication of the probable behavior of the soil as a pavement subgrade. This indication of behavior is, however, approximate. Performance different from that expected can occur due to a variety of reasons such as degree of compaction, degree of saturation, height of overburden, etc. The possibility of incorrectly predicting subgrade behavior can be largely eliminated by measuring soil strength. The strength of materials intended for use in flexible pavement structures is measured by the California Bearing Ratio (CBR) tests. Materials intended for use in rigid pavement structures are tested by the plate bearing method of test. Each of these tests is discussed in greater detail in the subsequent paragraphs.
a. California Bearing Ratio. The CBR test is basically a penetration test conducted at a uniform rate of strain. The force required to produce a given penetration in the material under test is compared to the force required to produce the same penetration in a standard crushed limestone. The result is expressed as a ratio of the two forces. Thus a material with a CBR value of 15 means the material in question offers 15% of the resistance to penetration that the standard crushed stone offers. Laboratory CBR tests should be performed in accordance with ASTM D 1883, Bearing Ratio of Laboratory-Compacted Soils. Field CBR tests should be conducted in accordance with the ASTM D 4429, Standard Test Method for Bearing Ratio of Soils in Place.
(1) Laboratory. Laboratory CBR tests are conducted on materials which have been obtained from the site and remolded to the density which will be obtained during construction. Specimens are soaked for 4 days to allow the material to reach saturation. A saturated CBR test is used to simulate the conditions likely to occur in a pavement which has been in service for some time. Pavement foundations tend to reach nearly complete saturation after about 3 years. Seasonal moisture changes also dictate the use of a saturated CBR design value since traffic must be supported during periods of high moisture such as spring seasons.
(2) Field. Field CBR tests can provide valuable information on foundations which have been in place for several years. The materials should have been in place for a sufficient time to allow for the moisture to reach an equilibrium condition. An example of this condition is a fill which has been constructed and surcharged for a long period of time prior to pavement construction.
(3) Gravelly Materials. CBR tests on gravelly materials are difficult to interpret. Laboratory CBR tests on gravel often yield CBR results which are too high due to the confining effects of the mold. The assignment of CBR values to gravelly subgrade materials may be based on judgment and experience. The information given in Table 2-3 may provide helpful guidance in selecting a design CBR value for a gravelly soil. Table 2-3 should not, however be used indiscriminately as a sole source of data. It is recommended that the maximum CBR for unstabilized grave1 subgrade be 50.
(4) Number of Tests. The number of CBR tests needed to properly establish a design value cannot be simply stated. Variability of the soil conditions encountered at the site will have the greatest influence on the number of tests needed. As an approximate “rule of thumb” three CBR tests on each different major soil type should be considered. The preliminary soil survey will reveal how many different soil types will be encountered. The design CBR value should be conservatively selected. Common paving engineering practice is to select a value which is one standard
CANCELLED
AC 150/5320-6D 7l7l95
deviation below the mean. As a rule, a design CBR value of 3 the lowest practical value which should be assigned. In instances where the subgrade strength is lower than CBR = 3, the subgrade should be improved through stabilization or other means to raise the design CBR value.
(5) Lime Rock Ratio. Some areas of the country use the lime rock ratio, LBR, to express soil strength. To convert LBR to CBR, multiply LBR by 0.8.
b. Plate Bearing Test. As the name indicates, the plate bearing test measures the bearing capacity of the pavement foundation. The result, k value, can be envisioned as the pressure required to produce a unit deflection of the pavement foundation. The plate bearing test result, k value, has the units of pounds per cubic inch (Mega-Newtons per cubic meter). Plate bearing tests should be performed in accordance with the procedures contained in AASHTO T 222.
(1) Sensitivity. Rigid pavement design is not too sensitive to the k value. An error in establishing a k value will not have a drastic impact on the design thickness of the rigid pavement. Plate bearing tests must be conducted in the field and are best performed on test sections which are constructed to the design compaction and moisture conditions. A correction to the k value for saturation is required to simulate the moisture conditions likely to be encountered by the in-service pavement.
(2) Number of Tests. Plate bearing tests are relatively expensive to perform and thus the number of tests which can be conducted to establish a design value is limited. Generally only 2 or 3 tests can be performed for each pavement feature. The design k value should be conservatively selected.
(3) Plate Size. The rigid pavement design and evaluation curves presented in this circular are based on a k value determined by a static plate load test using a 30-inch (762 mm) diameter plate. Use of a plate of smaller diameter will result in a higher k value than is represented in the design and evaluation curves.
(4) Subbase Effects. It is recommended that plate bearing tests be conducted on the subgrade and the results adjusted to account for the effect of subbase. Figure 2-4 shows the increase in k value for various thicknesses of subbase over a given subgrade k. Plate bearing tests conducted on top of subbase courses can sometimes yield erroneous results since the depth of influence beneath a 30” inch (762 mm) bearing plate is not as great as the depth of influence beneath a slab loaded with an aircraft landing gear assembly. In this instance a subbase layer can influence the response of a bearing plate more than the response of a loaded pavement.
(5) Stabilized Subbase. The determination of k value for stabilized layers is a difficult problem. The k value normally has to be estimated. It is recommended that the k value be estimated as follows. The thickness of the stabilized layer should be multiplied by a factor ranging from 1.2 to 1.6 to determine the equivalent thickness of well-graded crushed aggregate. The actual value in the 1.2 - 1.6 range should be based on the quality of the stabilized layer and the thickness of the slab relative to the thickness of the stabilized layer. High quality materials which are stabilized with high percentages of stabilizers should be assigned an equivalency factor which is higher than a lower quality stabilized material. For a given rigid pavement thickness, a thicker stabilized layer will influence pavement performance more than a thin stabilized layer and should thus be assigned a higher equivalency factor.
(6) Maximum k Value. It is recommended that a design k value of 500 lbs/in3 (136 MN/m’) not be exceeded for any foundation. The information presented in Table 2-3 gives general guidance as to probable k values for various soil types.
C. Additional Soil Strength Tests. Where stability of the underlying section is questionable, additional soil strength tests may be necessary. Direct shear tests (ASTM D 3080) or field vane tests (ASTM D 2573) may be required to adequately design the pavement structure.
CANCELLED
7l7l95 AC 150/5320=6D
Gi0 - &0 E-l z 0
500
400
300
200
100 90 80 70 60
50
(mm> 120 140 160 180 200 220 240 260 280 301r
I 1 I 1 I I I I I 1
I 1 I 1 I I I I I 1
0’793 4 5 6 7 8 9 10 11 12 THICKNESS OF SUBBASE, INCHES
- 120
- 100
- 90
- 80
- 70
- 60
- 30
- 25
- 20
- 15
FIGURE 2-4. EFFECT OF SUBBASE ON MODULUS OF SUBGRADE REACTION
CANCELLED
AC 150/5320-6D 7/7/95
207. SUBGRADE STABILIZATION. Subgrade stabilization should be considered if one or more of the following conditions exist: poor drainage, adverse surface drainage, frost, or need for a stable working platform. Subgrade stabilization can be accomplished through the addition of chemical agents or by mechanical methods.
FIGURE 2-4. EFFECT OF SUBBASE ON MODULUS OF SUBGRADE REACTION
a. Chemical Stabilization. Different soil types require different stabilizing agents for best results. The following publications are recommended to determine the appropriate type and amount of chemical stabilization for subgrade soils. US Army, Corps of Engineers, Technical Manual TM 5-818-2/AFM 88-6 Chapter 6 ; Technical Manual 5-825.UAFM 88-6 Chapter 2; Technical Manual 5-824-3/AFM 88-6, Chapter 3; Soil Cement Handbook, Portland Cement Association; and The Asphalt Institute Manual Series MS-19, A Basic Asphalt Emulsion Manual.
b. Mechanical Stabilization. In some instances subgrades cannot be adequately stabilized through the use of chemical additives. The underlying soils may be so soft that stabilized materials cannot be mixed and compacted over the underlying soils without failing the soft soils. Extremely soft soils may require bridging in order to construct the pavement section. Bridging can be accomplished with the use of thick layers of shot rock or cobbles. Thick layers of lean, porous concrete have also been used to bridge extremely soft soils. Geotextiles should be considered as mechanical stabilization over soft, fine-grained soils. Geotextiles can facilitate site access over soft soils and aid in reducing subgrade soil disturbance due to construction traffic. The geotextile will also function as a separation material to limit long-term weakening of pavement aggregate associated with contamination of the aggregate with underlying fine-grained soils. More information regarding construction over soft soils using geotextiles is provided in FHWA-KI-90-001 (see Appendix 4).
208. SEASONAL FROST. The design of pavements in areas subject to seasonal frost action requires special consideration. The detrimental effects of frost action may be manifested by nonuniform heave and in loss of soil strength during frost melting. Other related detrimental effects include: possible loss of compaction, development of pavement roughness, restriction of drainage, and cracking and deterioration of the pavement surface. Detrimental frost action requires three conditions be met simultaneously: first, the soil must be frost susceptible; secondly, freezing temperatures must penetrate into the frost susceptible soil; thirdly, free moisture must be available in sufficient quantities to form ice lenses.
a. Frost Susceptibility. The frost susceptibility of soils is dependent to a large extent on the size and distribution of voids in the soil mass. Voids must be of a certain critical size for the development of ice lenses. Empirical relationships have been developed correlating the degree of frost susceptibility with the soil classification and the amount of material finer than 0.02 mm by weight. Soils are categorized into four groups for frost design purposes, Frost Group 1 (FG-l), FG-2, FG-3, and FG-4. The higher the frost group number the more susceptible the soil, i.e., soils in frost group 4 are more frost susceptible than soils in frost groups 1, 2, or 3. Table 2-4 defines the frost groups.
b. Depth of Frost Penetration. The depth of frost penetration is a function of the thermal properties of the pavement and soil mass, the surface temperature, and the temperature of the pavement and soil mass at the start of the freezing season. Several methods are available to calculate the depth of frost penetration and subsurface temperatures. The method presented here is a simplification of a method based on the modified Berggren equation. This method requires the use of the air freezing index and the dry unit weight of the soil.
(1) Air Freezing Index. The air freezing index is a measure of the combined duration and magnitude of below freezing temperatures occurring during any given freezing season. the average daily temperature is used in the calculation of freezing index. For example, assume the average daily temperature is 10 degrees below freezing for 10 days. The freezing index would be calculated as follows, 10 degrees X IO days = 100 degree days. Ideally, air freezing indices should be based on actual data obtained from a meteorological station located in close proximity to the construction site. The air freezing index used for design (design air freezing index) should be based on the average of the 3 coldest winters in a 30 year period, if available, or the coldest winter observed in a 10 year period. Figures 2-6 and 2-7 show the approximate design air freezing indices for the lower United States and Alaska, respectively. The values shown in Figures 2-6 and 2-7 do not show local variation which may be substantial, especially in mountainous areas.
CANCELLED
8 0001
0051 000t 0052 000 1500
1500 2500
Design freezing index values are cumulative degree days of air temperature below 32° for the coldest year in a 10 year cycle or the average of the three coldest years in a 30 year cycle.
The isolines of design freezing values were drawn using data from nearly 400 U. S. Weather Bureau Stations shown as dots on the map. The map is olfered as a guide only. It doés not altempt to show local variations, which may be substantial, particularly in mountainous areas.
The actual design freezing index used should be computed for the specific project using temperature data from station nearest site. .See text.
OOSE
2500
2000
2500 200z 2000
1500
7/7/95
2500 2000
1000 500
AC
150/5320-6D
FIGURE 2-5. DISTRIBUTION OF DESIGN AIR FREEZING INDEXES IN THE CONTINENTAL U.S.
L
AC 150/5320-6D 7/7/95
-
FIGURE 2-6. DISTRIBUTION OF DESIGN AIR FREEZING INDEX VALUES IN ALASKA
FIGURE 2-6. DISTRIBUTION OF DESIGN AIR FREEZING INDEX VALUES IN ALASKA
CANCELLED
7m95 AC150/5320-6D
(2) Depth of Frost Penetration. The relationship between air freezing index and depth of frost penetration is shown in Figure 2-8. The thermal properties of the soil mass are reflected by differences in the dry unit weight of the subgrade soil. In the development of this method, the pavement is assumed to be either a 12 inch (300 mm) thick rigid pavement or a 20 inch (5 IO mm) thick flexible pavement. The depths of frost penetration shown on Figure 2-8 are measured from the pavement surface downward.
Frost Kind of Soil
TABLE 2-4. SOIL FROST GROUPS
TABLE 2-4. SOIL FROST GROUPS
Percentage finer than Soil Classification Group FG- I Gravelly Soils
0.02 mm by weight 3to 10 GW, GP, GW-GM, GP-GM
FG-2 Gravelly Soils Sands
lOto 3to 15 GM, GW-GM, GP-GM, SW, SP, SM, SW-SM SP-SM
FG-3
FG-4
Gravelly Soils Sands, except very fine silty sands Clays, PI above 12 Very fine silty sands All Silts Clays, PI = I2 or less Varied Clays and other fine prained banded sediments.
Over 20 Over I5
Over I5
-
GM, GC SM, SC
GM, GC SM, SC
CL, CH SM ML, MH CL, CL-ML CL, CH, ML, SM
C. Free Water. The availability of free water in the soil mass to freeze and form ice lenses is the third consideration which must be present for detrimental frost action to occur. Water may be drawn from considerable depths by capillary action, by infiltration from the surface or sides, or by condensation of atmospheric water vapor. Generally speaking, if the degree of saturation of the soil is 70% or greater, frost heave will probably occur. For all practical purposes, the designer should assume that sufficient water to cause detrimental frost action will be present.
CL, CH SM ML, MH CL, CL-ML CL, CH, ML, SM
d. Frost Design. The design of pavements to offset seasonal frost effects is presented in Chapter 3. A more detailed and rigorous discussion of frost action and its effects can be found in Research Report No. FAA/RDf74/30, see Appendix 3.
209. PERMAFROST. In arctic regions soils are often frozen at considerable depths year round. Seasonal thawing and refreezing of the upper layer of permafrost can lead to severe loss of bearing capacity and/or differential heave. In areas with continuous high-ice-content permafrost at shallow depths, satisfactory pavements are best ensured by restricting seasonal thawing to the pavement and to a non-frost susceptible base course. This approach is intended to prevent degradation (thawing) of the permafrost layer.
a. Susceptibility. The frost susceptibility of soils in permafrost areas is classified the same as given above in paragraph 206.
b. Depth of Thaw Penetration. Pavement design for permafrost areas must consider the depth of seasonal thaw penetration, The depth to which thawing temperatures penetrate into permafrost may be estimated using Figure 2-9. Use of Figure 2-9 requires inputs air thawing index, average wind speed during the thaw period, pavement type, and density of the permafrost layer. The air thawing index is expressed in degree days and is the difference between average daily temperature and 32 degrees Fahrenheit (0 degrees Celsius) multiplied by the number of days the temperature exceeds freezing. The thawing index used for design (design thawing index) should be based on the 3 warmest summers in the last 30 years of record. If 30 year records are not available, data from the warmest summer in the latest 10 year period may be used.
CANCELLED
AC 150/5320-6D 7m95
i-jw w fY Lx,
I f f ] ]
IiTiiiiii
CANCELLED
All Soil Moisture Assumed Frozen At Start of Thaw Period
- - --.- - Rigid Pavement
= Dry Unit Weight
Subqrade Soil = W&r Content
of Subgrade Soil
Pd =
RELATIONSHIP BETWEEN AIR THAWING INDEX AND THAW
RELATIONSHIP BETWEEN AIR THAWING INDEX AND THAW
Note:
1 foot = 0.3048 m
1 pcf - 16.02 kg/m’
1 mph = 1.609 km/h
0
1000
2000
3000
4000
5000
FIGURE 2-8. RELATIONSHIP BETWEEN AIR THAWING INDEX AND THAW PENETRATION INTO GRANULAR, NON-FROST SUSCEPTABLE SUBGRADE SOIL
CANCELLED
AC 150/5320-6D 7l7195
C. Muskeg. Muskeg is sometimes encountered in arctic areas. Muskeg is a highly organic soil deposit which is essentially a swamp. Every effort should be made to avoid pavement construction on this material. If construction in areas of muskeg is unavoidable and the soil survey shows the thickness of muskeg is less than 5 feet (1.5 m), the muskeg should be removed and replaced with granular fill. If the thickness of muskeg is too great to warrant removal and replacement, a 5 foot (1.5 m) granular fill should be placed over the muskeg. These thicknesses are based on experience and it should be anticipated that differential settlement will occur and considerable maintenance will be required to maintain a smooth surface. Use of a geotextile between the muskeg surface and the bottom of granular fill is recommended to prevent migration of the muskeg up into the granular till. In this application, the geotextile is considered to perform the function of separation. Additional information on the design and construction of geotextiles performing the separation function within pavement sections is provided in FHWA-HI-90-001 (see Appendix 4).
d. Permafrost Design. Design of pavements in areas of permafrost is discussed in Chapter 3. Further information on permafrost can be found in Research Report No. FAAfRDi74130, see Appendix 4.
CANCELLED
7m95 AC150/5320-6D
CHAPTER 3. PAVEMENT DESIGN
SECTION 1. DESIGN CONSIDERATIONS
SECTION 1. DESIGN CONSIDERATIONS
300. SCOPE. This chapter covers pavement design for airports serving aircraft with gross weights of 30,000 pounds (13 000 kg) or more. Chapter 5 is devoted to the design of pavements serving lighter aircraft with gross weights under 30,000 pounds (13 000 kg).
301. DESIGN PHILOSOPHY. The FAA policy of treating the design of aircraft landing gear and the design and evaluation of airport pavements as three separate entities is described in the Foreword to this advisory circular. The design of airport pavements is a complex engineering problem which involves a large number of interacting variables. The design curves presented in this chapter are based on the CBR method of design for flexible pavements and a jointed edge stress analysis for rigid pavements. Other design procedures such as those based on layered elastic analysis and those developed by The Asphalt Institute and the Portland Cement Association may be utilized to determine pavement thicknesses when approved by the FAA. These procedures will yield slightly different design thicknesses due to different basic assumptions. All pavement designs should be summarized on FAA Form 5100-1, Airport Pavement Design, which is considered to be part of the Engineer’s Report. An Engineer’s Report should be prepared for FAA review and approval along with initial plans and specifications. Because of thickness variations, the evaluation of existing pavements should be performed using the same method as was employed in the design. Procedures to be used in evaluating pavements are described in detail in Chapter 6 of this advisory circular. Details on the development of the FAA method of design are as follows:
- -
a. Flexible Pavements. The flexible pavement design curves presented in this chapter are based on the California Bearing Ratio (CBR) method of design. The CBR design method is basically empirical; however, a great deal of research has been done with the method and reliable correlations have been developed. Gear configurations are related using theoretical concepts as well as empirically developed data. The design curves provide the required total thickness of flexible pavement (surface, base, and subbase) needed to support a given weight of aircraft over a particular subgrade. The curves also show the required surface thickness. Minimum base course thicknesses are given in a separate table. A more detailed discussion of CBR design is presented in Appendix 2.
b. Rigid Pavements. The rigid pavement design curves in this chapter are based on the Westergaard analysis of edge loaded slabs. The edge loading analysis has been modified to simulate a jointed edge condition. Pavement stresses are higher at the jointed edge than at the slab interior. Experience shows practically all load induced cracks develop at jointed edges and migrate toward the slab interior. Design curves are furnished for areas where traffic will predominantly follow parallel or perpendicular to joints and for areas where traffic is likely to cross joints at an acute angle. The thickness of pavement determined from the curves is for slab thickness only. Subbase thicknesses are determined separately. A more detailed discussion of the basis for rigid pavement design is presented in Appendix 2.
302. BACKGROUND. An airfield pavement and the operating aircraft represent an interactive system which must be addressed in the pavement design process. Design considerations associated with both the aircraft and the pavement must be recognized in order to produce a satisfactory design. Careful construction control and some degree of maintenance will be required to produce a pavement which will achieve the intended design life. Pavements are designed to provide a finite life and fatigue limits are anticipated. Poor construction and lack of preventative maintenance will usually shorten the service life of even the best designed pavement.
a. Variables. The determination of pavement thickness requirements is a complex engineering problem. Pavements are subject to a wide variety of loadings and climatic effects. The design process involves a large number of interacting variables which are often difficult to quantify. Although a great deal of research work has been completed and more is underway, it has been impossible to arrive at a direct mathematical solution of thickness requirements. For this reason the determination of pavement thickness must be based on the theoretical analysis of load distribution through pavements and soils, the analysis of experimental pavement data, and a study of the performance of pavements under actual service conditions. Pavement thickness curves presented in this chapter have been developed through correlation of the data obtained from these sources. Pavements designed in accordance with these standards are intended to provide a structural life of 20 years that is free of major maintenance if no major changes in forecast traffic are encountered. It is
CANCELLED
AC 150/5320-6D 7l7195
likely that rehabilitation of surface grades and renewal of skid resistant properties will be needed before 20 years due to destructive climatic effects and deteriorating effects of normal usage.
b. Structural Design. The structural design of airport pavements consists of determining both the overall pavement thickness and the thickness of the component parts of the pavement. There are a number of factors which influence the thickness of pavement required to provide satisfactory service. These include the magnitude and character of the aircraft loads to be supported, the volume of traffic, the concentration of traffic in certain areas, and the quality of the subgrade soil and materials comprising the pavement structure.
303. AIRCRAFT CONSIDERATIONS.
a. Load. The pavement design method is based on the gross weight of the aircraft. For design purposes the pavement should be designed for the maximum anticipated takeoff weight of the aircraft. The design procedure assumes 95 percent of the gross weight is carried by the main landing gears and 5 percent is carried by the nose gear. AC 150/5300-13, Airport Design, lists the weight of nearly all civil aircraft. Use of the maximum anticipated takeoff weight is recommended to provide some degree of conservatism in the design and is justified by the fact that changes in operational use can often occur and recognition of the fact that forecast traffic is approximate at best. By ignoring arriving traffic some of the conservatism is offset.
b. Landing Gear Type and Geometry. The gear type and configuration dictate how the aircraft weight is distributed to the pavement and determine pavement response to aircraft loadings. It would have been impractical to develop design curves for each type of aircraft. However, since the thickness of both rigid and flexible pavements is dependent upon the gear dimensions and the type of gear, separate design curves would be necessary unless some valid assumptions could be made to reduce the number of variables. Examination of gear configuration, tire contact areas, and tire pressure in common use indicated that these follow a definite trend related to aircraft gross weight. Reasonable assumptions could therefore be made and design curves constructed from the assumed data. These assumed data are as follows:
(1) Single Gear Aircraft. No special assumptions needed.
(2) Dual Gear Aircraft. A study of the spacing between dual wheels for these aircraft indicated that a dimension of 20 inches (0.5 1 m) between the centerline of the tires appeared reasonable for the lighter aircraft and a dimension of 34 inches (0.86 m) between the centerline of the tires appeared reasonable for the heavier aircraft.
(3) Dual Tandem Gear Aircraft. The study indicated a dual wheel spacing of 20 inches (0.51 m) and a tandem spacing of 45 inches (1.14 m) for lighter aircraft, and a dual wheel spacing of 30 inches (0.76 m) and a tandem spacing of 55 inches (1.40 m) for the heavier aircraft are appropriate design values.
(4) Wide Body Aircraft. Wide body aircraft; i.e., B-747, DC-lo, and L-101 1 represent a radical departure from the geometry assumed for dual tandem aircraft described in paragraph (c) above. Due to the large differences in gross weights and gear geometries, separate design curves have been prepared for the wide body aircraft.
C. Tire Pressure. Tire pressure varies between 75 and 200 PSI (516 to 1 380 kPa) depending on gear configuration and gross weight. It should be noted that tire pressure asserts less influence on pavement stresses as gross weight increases, and the assumed maximum of 200 PSI (1 380 kPa) may be safely exceeded if other parameters are not exceeded and a high stability surface course is used.
d. Traffic Volume. Forecasts of annual departures by aircraft type are needed for pavement design. Information on aircraft operations is available from Airport Master Plans, Terminal Area Forecasts, the National Plan of Integrated Airport Systems, Airport Activity Statistics and FAA Air Traffic Activity. These publications should be consulted in the development of forecasts of annual departures by aircraft type.
304. DETERMINATION OF DESIGN AIRCRAFT. The forecast of annual departures by aircraft type will result in a list of a number of different aircraft. The design aircraft should be selected on the basis of the one requiring the
CANCELLED
7l7l95 AC 150/5320-6D
greatest pavement thickness. Each aircraft type in the forecast should be checked to determine the pavement thickness required by using the appropriate design curve with the forecast number of annual departures for that aircraft. The aircraft type which produces the greatest pavement thickness is the design aircraft. The design aircraft is not necessarily the heaviest aircraft in the forecast.
305. DETERMINATION OF EQUIVALENT ANNUAL DEPARTURES BY THE DESIGN AIRCRAFT.
a. Conversions. Since the traffic forecast is a mixture of a variety of aircraft having different landing gear types and different weights, the effects of all traffic must be accounted for in terms of the design aircraft. First, all aircraft must be converted to the same landing gear type as the design aircraft. Factors have been established to accomplish this conversion. These factors are constant and apply to both flexible and rigid pavements. They represent an approximation of the relative fatigue effects of different gear types. Much more precise and theoretically rigorous factors could be developed for different types and thicknesses of pavement. However, such precision would be impractical for hand calculation as numerous iterations and adjustments would be required as the design evolved. At this stage of the design process such precision is not warranted. The following conversion factors should be used to convert from one landing gear type to another:
To Convert From To Multiply Departures by single wheel dual wheel 0.8 single wheel dual tandem 0.5 dual wheel dual tandem 0.6 double dual tandem dual tandem 1.0 dual tandem single wheel 2.0 dual tandem dual wheel 1.7 dual wheel single wheel 1.3 double dual tandem dual wheel 1.7
Secondly, after the aircraft have been grouped into the same landing gear configuration, the conversion to equivalent annual departures of the design aircraft should be determined by the following formula:
log R,
w2 1 = log R, X(7)2
1
where: R, = equivalent annual departures by the design aircraft R, = annual departures expressed in design aircraft landing gear W , = wheel load of the design aircraft W, = wheel load of the aircraft in question
For this computation 95 percent of the gross weight of the aircraft is assumed to be carried by the main landing gears. Wide body aircraft require special attention in this calculation. The procedure discussed above is a relative rating which compares different aircraft to a common design aircraft. Since wide body aircraft have significantly different landing gear assembly spacings than other aircraft, special considerations are needed to maintain the relative effects. This is done by treating each wide body as a 300,000-pound (136 100 kg) dual tandem aircraft when computing equivalent annual departures. This should be done in every instance even when the design aircraft is a wide body. After the equivalent annual departures are determined, the design should proceed using the appropriate design curve for the design aircraft. For example if a wide body is the design aircraft, all equivalent departures should be calculated as described above; then the design curve for the wide body should be used with the calculated equivalent annual departures.
b. Example: Assume an airport pavement is to be designed for the following forecast traffic:
CANCELLED
AC150/5320-6D 7/7/95
Aircraft Gear Type
727-100 727-200 707-320B DC-g-30 cv-880 737-200 L-101 l-100 747-100
dual dual dual tandem
dual dual tandem
dual dual tandem
double dual
tandem
Average
Annual Departures
3,760 9,080 3,050 5,800 400 2,650 1,710 85
Maximum Takeoff Weight
lbs. (kg)
160,000 (72600) 190,500 (86500) 327,000 (148 500) 108,000 (49 ow 184,500 (83 948) 115,500 (52 440) 450,000 (204 120) 700,000 (3 17 800)
(1) Determine Design Aircraft. A pavement thickness is determined for each aircraft in the forecast using the appropriate design curves. The pavement input data, CBR, K value, flexural strength, etc., should be the same for all aircraft. Aircraft weights and departure levels must correspond to the particular aircraft in the forecast. In this example the 727-200 requires the greatest pavement thickness and is thus the design aircraft.
(2) Group Forecast Traffic into Landing Gear of Design Aircraft. In this example the design aircraft is equipped with a dual wheel landing gear so all traffic must be grouped into the dual wheel configuration.
(3) Convert Aircraft to Equivalent Annual Departures of the Design Aircraft. After the aircraft mixture has been grouped into a common landing gear configuration, the equivalent annual departures of the design aircraft can be calculated.
Aircraft Equi. Dual Wheel Load Wheel Load of Design Equi. Annual Gear Departs. lbs. (kg) Aircraft Departs lbs. (kg) Design Aircraft 727-100 3,760 38,000 (17 240) 45,240 (20 520) 1,891 727-200 9,080 45,240 (20 520) 45,240 (20 520) 9,080 707-320B 5,185 38,830 (17 610) 45,240 (20 520) 2,764 DC-g-30 5,800 25,650 (11 630) 45,240 (20 520) 682 cv-880 680 21,910 (9 940) 45,240 (20 520) 94 737-200 2,650 27,430 (12,440) 45,240 (20 520) 463 747 145 35,625’ (16 160) 45,240 (20520) 83 L-101 1 2,907 35,625’ (16 160) 45,240 (20,520) 1,184 Total = 16,241 ‘Wheel loads for wide body aircraft will be taken as the wheel load for a 300,000-pound (136 100 kg) aircraft for equivalent annual departure calculations.
(4) Final Result. For this example the pavement would be designed for 16,000 annual departures of a dual wheel aircraft weighing 190,500 pounds (86 500 kg). The design should, however, provide for the heaviest aircraft in the traffic mixture, B747-100, when considering depth of compaction, thickness of asphalt surface, drainage structures, etc.
C. Other Methods. More refined methods of considering mixed traffic are possible. These refined methods may consider variations in material properties due to climatic effects, take-off versus landing loads, aircraft tread dimensions, etc. Use of these refined methods is allowable under the conditions given in paragraph 301.
-
306. TRAFFIC DISTRIBUTION. Research studies have shown that aircraft traffic is distributed laterally across runways and taxiways according to statistically normal (bell shaped) distribution. FAA Report No. FAA-RD-36, Field Survey and Analysis of Aircraft Distribution on Airport Pavements, dated February 1975, contains the latest research information on traffic distribution. The design procedures presented in this circular incorporate the statistically normal distribution in the departure levels. In addition to the lateral distribution of traffic across pavements, traffic distribution and nature of loadings are considered for aprons, and high speed turnoffs.
CANCELLED
717195 AC 150/5320-6D
307. TYPICAL SECTIONS. Airport pavements are generally constructed in uniform, full width sections. Runways may be constructed with a transversely variable section, if practical. A variable section permits a reduction in the quantity of materials required for the upper paving layers of the runway. However, more complex construction operations are associated with variable sections and are usually more costly. The additional construction costs may negate any savings realized from reduced material quantities. Typical plan and section drawings for transversely variable section runway pavements are shown in Figure 3-1. Deviations from these typical sections will be common
due to the change inherent in staged construction projects where runways are extended and the location of taxiways is uncertain. As a general rule-of-thumb the designer should specify full pavement thickness T where departing traffic will be using the pavement; pavement thickness of 0.9T will be specified where traffic will be arrivals such as high speed turnoffs; and pavement thickness of 0.7T will be specified where pavement is required but traffic is unlikely such as along the extreme outer edges of the runway. Note that the full-strength keel section is 50 feet (15 m) on the basis of the research study discussed in paragraph 306a.
308. FROST AND PERMAFROST DESIGN. The design of an airport pavement must consider the climatic conditions which will act on the pavement during its construction and service life. The protection of pavements from the adverse effects of seasonal frost and permafrost effects are considered in the design of airport pavements as discussed below.
a. Seasonal Frost. The adverse effects of seasonal frost have been discussed in Chapter 2. The design of pavements in seasonal frost areas may be based on either of two approaches. The first approach is based on the control of pavement deformations resulting from frost action. Under this approach, sufficient combined thickness of pavement and non-frost-susceptible material must be provided to eliminate, or limit to an acceptable amount, frost penetration into the subgrade and its adverse effects. The second approach is based on providing adequate pavement load carrying capacity during the critical frost melting period. The second approach provides for the loss of load carrying capacity due to frost melting but ignores the effects of frost heave. Three design procedures have been developed which encompass the above approaches and are discussed below.
(1) Complete Frost Protection. Complete frost protection is accomplished by providing a sufficient thickness of pavement and non-frost-susceptible material to totally contain frost penetration. This method is intended to prevent underlying frost susceptible materials from freezing. To use the complete protection method , the depth of frost penetration is determined by the procedure given in Chapter 2. The thickness of pavement required for structural support is compared with the depth of frost penetration computed. The difference between the pavement thickness required for structural support and the computed depth of frost penetration is made up with non-frostsusceptible material. Depending on grades and other considerations, provision for complete protection may involve removal and replacement of a considerable amount of subgrade material. Complete frost protection is the most positive, and is usually the most costly, method of providing frost protection.
(2) Limited Subgrade Frost Penetration. The limited subgrade frost penetration method is based on holding frost heave to a tolerable level. Frost is allowed to penetrate a limited amount into the underlying frost susceptible subgrade. Sixty five (65%) of the depth of frost penetration is made up with non-frost-susceptible material. Use of the method is simi@r to the complete protection method. Additional frost protection is required if the thickness of the strnctural section is less than 65% of the frost penetration. The limited subgrade frost penetration method allows a tolerable (based on experience) amount of frost heave.
(3) Reduced Subgrade Strength. The reduced subgrade strength method is based on the concept of providing a pavement with adequate load carrying capacity during the frost melting period. This method does not consider the effects of frost heave. Use of the reduced subgrade strength method involves assigning a subgrade strength rating to the pavement for the frost melting period. The various soil frost groups as defined in Chapter 2, should be assigned strength ratings as shown below:
CANCELLED
A TRANSI I
A TRANSI I
NOTES -
2” (Icm) MINIMUM
I - - I I I I I
S U B B A S E 0 3 SURFACE,BASE,PCC,ETC.,THICKNESS
AS INDICATED ON DESIGN CHART.
4 A A *+ F* MINIMUM 12” (30cm) UP TO 30”(90cm) r” - 05 6 @ 2 5 ’ (7.6m) -h’o’ Lao A L L O W A B L E .
5 05 FOR RUNWAYS WIDER THAN 150’(45.7m)
v I RUNWAY WIDTHS IN ACCORDANCE WITH
v I RUNWAY WIDTHS IN ACCORDANCE WITH
APPLICABLE ADVISORY CIRCULAR.
TRANSVERSE SLOPES IN ACCORDANCE
WITH APPLICABLE ADVISORY CIRCULAR.
LEGEND THIS DIMENSION W I L L INCREASE.
I 1 T H I C K N E S S =T
1 1 ’ ’ ’ ’ ’ 1 THICKNESS TAPERS = T .-*(),7T
17 /l//J THICKNESS=O,ST
.*.a … ‘.‘.... * , … t,*. .( .v.:r.1 THICKNESS f 0.7 T
FIGURE 3-1. TYPICAL PLAN AND CROSS SECTION FOR RUNWAY PAVEMENT
FIGURE 3-1. TYPICAL PLAN AND CROSS SECTION FOR RUNWAY PAVEMENT
CANCELLED
7/7/95 AC 150/5320-6D
TABLE 3-l. REDUCED SUBGRADE STRENGTH RATINGS Frost Group Flexible Pavement CBR Value Rigid Pavement k-value FG-1 9 50 FG-2 7 40 FG-3 4 25 FG-4 Reduced Subgrade Strength Method Does Not Apply
The required pavement thicknesses are determined from the appropriate design curves using the reduced subgrade strength ratings. Pavement thicknesses thus established reflect the requirements for the subgrade in its weakened condition due to frost melting.
b. Applications. Due to economic considerations, the maximum practical depth of frost protection that should be provided is normally 72 inches (1.8 m). The recommended applications of the three methods of frost protection discussed above are as follows. In addition to these recommended applications, local experience should be given strong consideration when designing for frost conditions.
(1) Complete Frost Protection. The complete frost protection method applies only to FG-3 and FG-4 soils which are extremely variable in horizontal extent. These soil deposits are characterized by very large, frequent, and abrupt changes in frost heave potential. The variability is such that the use of transition sections is not practical.
(2) Limited Subgrade Frost Penetration. This design method should be used for FG-4 soils except where the conditions require complete protection, see (1) above. The method also applies to soils in frost groups FG-1, FG-2, and FG-3 when the functional requirements of the pavement permit a minor amount of frost heave. Consideration should be given to using transition sections where horizontal variability of frost heave potential permits.
(3) Reduced Subgrade Strength. The reduced subgrade strength method is recommended for FG-I, FG-2, and FG-3 subgrades which are uniform in horizontal extent or where the functional requirements of the pavement will permit some degree of frost heave. the method may also be used for variable FG-1 through FG-3 subgrades for less sensitive pavements which are subject to slow speed traffic and heave can be tolerated.
C. Permafrost, The design of pavements in permafrost regions must consider not only the effects of seasonal thawing and refreezing, but also the effects of construction on the existing thermal equilibrium. Changes in the subsurface thermal regime may cause degradation of the permafrost table, resulting in severe differential settlements drastic reduction of pavement load carrying capacity. Gravel surfaced pavements are rather common in permafrost areas and generally will provide satisfactory service. These pavements often exhibit considerable distortion but are rather easily regraded. The absence of a waterproof surface is not a great problem because these areas are usually have low precipitation. Three design methods for asphaltic or concrete surfaced pavements are discussed below.
(1) Complete Protection Method. The objective of the complete protection method is to ensure that the underlying permafrost remains frozen year round. Seasonal thawing is restricted to non-frost-susceptible materials. This method is analogous to the complete frost protection method of design for seasonal frost. The thickness of pavement required for structural support is first determined. The depth of seasonal thaw is then computed as described in Chapter 2 or using information based on local experience. The difference between the depth of seasonal thaw and the thickness needed for structural support is the amount of non-frost-susceptible material which must be provided to fully contain the depth of seasonal thaw. The use of relatively high moisture retaining soils, such as uniformly graded sands, should be considered. If some heaving can be tolerated, the use of frost-susceptible soils in the FG- 1 or FG-2 groups may also be considered. If FG-1 or FG-2 soils are used, they must be placed so as to be as uniform as possible. Normally economic considerations will limit the depth of treatment to a maximum of 6 feet (1.8 m).
(2) Reduced Subgrade Strength Method. If conditions are such that the complete protection method of design is not practical, the design may be based on the reduced subgrade strength method. The use of this
CANCELLED
AC 150/5320-6D 7f7l95
method for permafrost design is identical to that presented in paragraph 308b(3) above. this method should provide a pavement with sufficient structural support during the seasonal permafrost thaw period but will likely result in differential heaving. If practical, it may be advisable to delay paving for 2 or 3 years to allow the embankment to reach equilibrium.
(3) Insulating Panels. A third approach which is not as common is the use of insulating panels beneath the pavement structure to protect against degradation of the permafrost. This method can lead to problems if the insulating panels are crushed by the weight of the overburden or by the live loads. Crushing of the cell structure of the insulation results in loss of insulating properties and failure to serve its intended purpose. Pavements using this technique must be very carefully constructed and may be subject to load limitations because of the need to guard against crushing the insulating panels. A significant change in the weight of using aircraft may fail the insulating panels. Since the FAA has no standards or design criteria for the use of insulating panels, their use on federally funded construction requires FAA approval on a case-by-case basis.
CANCELLED
7l7l95 AC150/5320-61)
SECTION 2. FLEXIBLE PAVEMENT DESIGN
SECTION 2. FLEXIBLE PAVEMENT DESIGN
309. GENERAL. Flexible pavements consist of a hot mix asphalt wearing surface placed on a base course and, when required by subgrade conditions, a subbase. The entire flexible pavement structure is ultimately supported by the subgrade. Definitions of the function of the various components are given in the following paragraphs. For some aircraft the base and subbase should be constructed of stabilized materials. The requirements for stabilized base and subbase are also discussed in this section.
310. HOT MIX ASPHALT SURFACING. The hot mix asphalt surface or wearing course must prevent the penetration of surface water to the base course; provide a smooth, well-bonded surface free from loose particles which might endanger aircraft or persons; resist the shearing stresses induced by aircraft loads; and furnish a texture of nonskid qualities, yet not cause undue wear on tires. To successfully fulfill these requirements, the surface must be composed of mixtures of aggregates and bituminous binders which will produce a uniform surface of suitable texture possessing maximum stability and durability. Since control of the mixture is of paramount importance, these requirements can best be achieved by use of a central mixing plant where proper control can be most readily obtained. A dense-graded hot mix asphalt concrete such as Item P-401 produced in a central mixing plant will most satisfactorily meet all the above requirements. Whenever a hot mix asphalt surface is subject to spillage of fuel, hydraulic fluid, or other solvents; such as at aircraft fueling positions and maintenance areas, protection should be provided by a solvent resistant surface.
-
311. BASE COURSE. The base course is the principal structural component of the flexible pavement. It has the major function of distributing the imposed wheel loadings to the pavement foundation, the subbase and/or subgrade. The base course must be of such quality and thickness to prevent failure in the subgrade, withstand the stresses produced in the base itself, resist vertical pressures tending to produce consolidation and resulting in distortion of the surface course, and resist volume changes caused by fluctuations in its moisture content. In the development of pavement thickness requirements, a minimum CBR value of 80 is assumed for the base course. The quality of the base course depends upon composition, physical properties and compaction. Many materials and combinations thereof have proved satisfactory as base courses. They are composed of select, hard, and durable aggregates. Specifications covering the quality of components, gradation, manipulation control, and preparation of various types of base courses for use on airports for aircraft design loads of 30,000 pounds (14 000 kg) or more are as follows:
Continue reading ↓ 120 of 410 passages shown