Radar Vectors
Advisory Circular Current Issued Sep 30, 2011 AAS-100 86 pages Copy saved Nov 18, 2026

AC 150/5370-11B Use of Nondestructive Testing in the Evaluation of Airport Pavements

Focuses on nondestructive testing (NDT) equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement. It also briefly introduces other types of nondestructive measuring equipment to illustrate how supplementing NDT data with other test data may improve the quality and reliability of the pavement evaluation. This version updates Chapter 8, NDT-Based Evaluation and Design Updates, to reflect the requirements of the pavement design program FAARFIELD rather than the previous design program LEDFAA. See also Airport Design Software.

Official source ↗ Open PDF

Advisory Circular

U.S. Department of Transportation

Federal Aviation Administration

Subject: Use of Nondestructive Testing in the Evaluation of Airport Pavements

Date: 9/30/11 Initiated by: AAS-100

AC No.: 150/5370-11B Change:

1. Purpose. This advisory circular (AC) focuses on nondestructive testing (NDT) equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement. It also briefly introduces other types of nondestructive measuring equipment to illustrate how supplementing NDT data with other test data may improve the quality and reliability of the pavement evaluation.

2. Application. The Federal Aviation Administration (FAA) recommends the guidelines and standards in this AC for data collection equipment and methods of data analysis used to conduct NDT. In general, use of this AC is not mandatory. However, use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and with revenue from the Passenger Facility Charges (PFC) Program. See Grant Assurance No. 34, “Policies, Standards, and Specifications,” and PFC Assurance No. 9, “Standard and Specifications.”

3. Cancellation. AC 150/5370-11A Use of Nondestructive Testing Devices in the Evaluation of Airport Pavements, dated December 29, 2004, is cancelled.

4. Principal Changes.

a. Since the previous revision, the FAA has developed and implemented the pavement design program FAARFIELD. Chapter 8 - NDT-BASED EVALUATION AND DESIGN INPUTS is updated to reflect the requirements of FAARFIELD rather than the previous design program LEDFAA.

b. The document has been reformatted to provide a better presentation in the PDF format used for distribution. We switched to a one column format. We also moved the figures and tables from the back up to their first citation for better illustration of the text. We also enlarged the equations for better readability.

c. The numbering was adjusted to include lead paragraphs in the beginnings of some chapters, so they were not un-numbered.

5. Related Advisory Circulars. The following ACs provides additional information regarding NDT and structural analysis of airport pavements:

a. 150/5320-6, Airport Pavement Design and Evaluation.

b. 150/5320-12, Measurement, Construction, and Maintenance of Skid Resistant Airport Pavement Surfaces.

c. 150/5335-5, Standardized Method of Reporting Airport Pavement Strength PCN.

d. 150/5380-6, Guidelines and Procedures for Maintenance of Airport Pavements.

ii

6. Organization of this AC. The following chapters in this AC present an overview of the NDT data collection process and equipment that are used to collect the field data. The AC then focuses on how to prepare a test plan and develop procedures that should be used for data acquisition. The final chapters focus on processing the raw data to obtain pavement material characteristics that can then be used to evaluate a pavement’s load-carrying capacity, remaining structural life, or strengthening requirements.

7. Use of Metrics. To promote an orderly transition to metric units, this AC contains both English and metric dimensions. If the conversion is not exact, the English units govern.

8. Copies of this AC. The FAA is in the process of making all ACs available to the public through the Internet. These ACs may be found by selecting the Regulations and Policies link on the FAA home page (www.faa.gov).

Michael J. O’Donnell

Director of Airport Safety and Standards

iii

Table of Contents

CHAPTER 1. INTRODUCTION 1 1. General … 1 2. Background … 1 3. Limitations to NDT … 2 CHAPTER 2. DESCRIPTION OF NDT PROCESS 3 4. General … 3 5. Pavement Stiffness and Sensor Response … 3 6. Deflection Basin … 4 7. Use of NDT Data … 6 CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT 7 8. General … 7 9. Categories of Equipment … 7 10. General Requirements for NDT Equipment … 10 11. Static Devices … 11 12. Vibratory Devices … 12 13. Impulse Devices … 13 14. Use of Historical Data … 17 CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT 19 15. General … 19 16. Need for Standardization … 19 17. FAA Sensitivity Study … 20 18. Summary of FAA Policy … 22 CHAPTER 5. TEST PLANNING 23 19. General … 23 20. Justification for NDT … 23 21. NDT Test Objectives … 24 22. NDT Test Types … 24 23. Test Locations and Spacing … 25 24. NDT Test Sketches … 27 25. Special Considerations … 29 CHAPTER 6. TEST PROCEDURES 31 26. General … 31 27. Equipment Mobilization … 31 28. Startup Operations … 32 29. Data Collection … 32 30. Special Test Conditions … 34 31. Onsite Review of Data … 35 CHAPTER 7. DEFLECTION DATA ANALYSES 37 32. General … 37 33. Overview of Process … 37 34. Process Raw Deflection Data … 39 35. Back-Calculation Analysis … 43 36. PCC Joint Analysis … 62 37. PCC Void Analysis … 65 38. PCC Durability Analysis … 67

iv

39. Summary … 69 CHAPTER 8. NDT-BASED EVALUATION AND DESIGN INPUTS 71 40. General … 71 41. Statistically Derived Inputs … 71 42. Using NDT Results in FAA Analysis Programs … 75 43. PCC Loss of Support … 77 44. Summary … 78

List of Figures

Figure 1. Impulse Load Created by FWD … 4 Figure 2. Sensors Spaced Radially from the Load Plate … 4 Figure 3. Schematic of Deflection Basin … 5 Figure 4. Comparison of Deflection Basin of Three Pavements … 6 Figure 5. Static and Dynamic Force Components for Vibratory NDT … 7 Figure 6. Time to Peak Load for Impulse-Based NDT Equipment … 8 Figure 7. Benkleman Beam … 11 Figure 8. Dynaflect Deflection Trailer … 12 Figure 9. Road Rater … 13 Figure 10. Kuab FWD … 15 Figure 11. Dynatest FWD … 15 Figure 12. Carl Bro FWD/HWD and LWD Trailer, Van-Integrated or Portable … 16 Figure 13. JILS HWD … 17 Figure 14. Evaluation of HWD Force Linearity in Terms of ISM … 22 Figure 15. Evaluation of HWD Force Linearity in Terms of Subgrade Elastic Modulus … 22 Figure 16. NDT Test Locations within a PCC Slab … 24 Figure 17. Load Transfer across A PCC Joint … 25 Figure 18. Example Runway or Taxiway Sketch When Centerline Lies on Slab Joint … 27 Figure 19. Example Runway or Taxiway Sketch When Centerline Does Not Lie on Slab Joint … 27 Figure 20.

Figure 1: picture of page 4Figure 1 · page 4
Picture of the page from the copy saved here

Example Runway or Taxiway Sketch for HMA Pavements … 28 Figure 21. Thermal Curling in PCC Slab from Temperature Changes … 29 Figure 22. Location of Additional Sensors for Corner and Joint Testing … 34 Figure 23. NDT Data Analysis And Design Flowchart … 37 Figure 24. ISM Plot to Identify Pavement Section Breaks … 40 Figure 25. Normalized Deflection Plot Used to Identify Pavement Section Breaks … 41 Figure 26. Normalized Subgrade Deflection Plot Used to Identify Pavement Sections … 42 Figure 27. Process for Data Preparation and Back-Calculation Method Selection … 44 Figure 28. Flowchart for Closed-Form Back-Calculation Using Area Method … 46 Figure 29. Basin Area for SHRP Four-Sensor Configuration … 47 Figure 30. Comparison of Measured and Calculated Deflection Basins … 55 Figure 31. Back-Calculation Procedures for an Elastic Layer Based Analysis … 60 Figure 32. Initial BAKFAA Run for Example 2 … 61 Figure 33. Second BAKFAA Run for Example 2 … 61 Figure 34. Output From Second BAKFAA Run for Example 2 … 62 Figure 35.

Figure 21: picture of page 4Figure 21 · page 4
Picture of the page from the copy saved here

Deflection vs. Stress LTE Relationship for 12 Inch (30 cm) Diameter Load Plate … 64 Figure 36. Example Plot of Transverse Joint LTE∆ for a 10,000 Ft (3,000 m) Taxiway … 65 Figure 37. Void Detection Beneath PCC Slabs … 66 Figure 38. Example Plot of Transverse Joint Voids for a 10,000 Ft (3,000 m) Taxiway … 67 Figure 39. Example Plot of ISMratio for Transverse Joint for HMA Overlaid PCC … 69 Figure 40. Histogram of ISM Values for Section 3 in Figure 24 … 72

v

List of Tables

Figure 36: picture of page 4Figure 36 · page 4
Picture of the page from the copy saved here

Table 1. Summary of Nondestructive Testing Measuring Equipment … 9 Table 2. Detailed Specifications for Selected FWDs and HWDs … 14 Table 3. ASTM Standards for Deflection Measuring Equipment … 19 Table 4. Common Sensor Configurations … 21 Table 5. Typical Runway and Taxiway Test Locations and Spacing, Feet (m) … 26 Table 6. Typical Apron Test Locations and Frequency … 26 Table 7. FAA Software Tools for Pavement Analysis, Evaluation, And Design … 38 Table 8. Theoretical Basis of FAA Software Tools … 39 Table 9. Required Sensor Distance (Inch) From Load Plate with 12 Inch (30 cm) Diameter … 42 Table 10. Area-Based Constants for Equation 8 … 43 Table 11. Type of Back-Calculation Software Tool Required for Each Load Scenario … 45 Table 12. Constants for D, (Equation 11) … 52 Table 13. Typical Modulus Values and Ranges for Paving Materials … 52 Table 14. Typical Poisson’s Ratios for Paving Materials … 53 Table 15. Linear Analysis Back- Calculation Programs … 54 Table 16. Nonlinear Analysis Back-Calculation Programs … 58 Table 17. Seed Modulus and Poisson’s Ratios for Example Problem 2 … 59 Table 18. Pavement Joint Performance Ratings … 60 Table 19. Statistical Summary of ISM Values for Each Section in Figure 24 … 64 Table 20. Required FAA Advisory Circular Evaluation and Design Inputs … 74 Table 21. Allowable Modulus Values for FAARFIELD (AC 150/5320-6), psi (MPa) … 75 Table 22. HMA Pavement Base and Subbase Modulus and Equivalency Factor Inputs … 76 Table 23. Recommended Reduced Values for Loss of Support Conditions … 78

Figure 24: picture of page 4Figure 24 · page 4
Picture of the page from the copy saved here

vi

Intentionally Left Blank

CHAPTER 1. INTRODUCTION 1

CHAPTER 1. INTRODUCTION

1 . General. Nondestructive testing (NDT) can make use of many types of data-collection equipment and methods of data analysis. In most cases, the data can be used to evaluate the structural or functional condition of a pavement. This AC focuses on collecting and analyzing NDT data, which are used to accomplish the following:

CHAPTER 1. INTRODUCTION › 2. Background.

a. Evaluate the load-carrying capacity of existing pavements.

b. Provide material properties of in-situ pavement and subgrade layers for the design of pavement rehabilitation alternatives that include extensive maintenance and repair work (restoration), functional and structural overlays, partial reconstruction (for example, runway keel), and complete reconstruction.

c. Compare parts of a pavement system to each other to gain relative strength and/or condition within that section. The results of the NDT can show which segments are the strongest and which are the weakest. These results can then be used to focus follow-on testing.

d. Provide structural performance data to supplement pavement condition index (PCI) survey data in an Airport Pavement Management System (APMS).

To accomplish these objectives, this AC provides an overview of the various types of NDT equipment; identifies those scenarios where NDT provides the most benefit to the engineer and owner; describes how NDT test plans should be developed for data collection; presents several methods for using the NDT data to characterize a pavement; and describes how the results from NDT should be used as inputs to evaluation, design, and pavement management analyses that comply with FAA policy.

There are many software programs that can be used to collect and analyze NDT data, and this AC will reference many of them. The FAA’s back-calculation program, BAKFAA, can be downloaded from the FAA website and can be used to analyze NDT data, subject to the limitations discussed herein.

2 . Background. Recent advances in hardware and software technology have significantly improved NDT equipment, data collection, and analysis software. Not only has NDT work been conducted on hundreds of airport pavements throughout the world, it has been extensively used to evaluate and design interstate highways, state highways, tollways, county roads, city streets, and seaports. NDT is also being used by researchers to improve pavement evaluation and design methodologies.

The Federal Highway Administration (FHWA) uses NDT equipment to collect data at hundreds of test section sites throughout the U.S. The FAA currently uses NDT equipment to collect data at the National Airport Pavement Test Facility (NAPTF) in Atlantic City, NJ to advance airport pavement evaluation and design methods.

There are several advantages to using NDT in lieu of or as a supplement to traditional destructive tests. Most important, is the capability to quickly gather data at several locations while keeping a runway, taxiway, or apron operational during these 2-minute to 3-minute tests, provided the testing is under close contact with Air Traffic Control. Without NDT, structural data must be obtained from numerous cores, borings, and excavation pits on an existing airport pavement. This can be very disruptive to airport operations. For example, to conduct a plate load test for measuring in-situ modulus of subgrade reaction, k, tests, 4 ft (1.2 m) by 6 ft (1.8 m) pits are prepared by removing each pavement layer until the subgrade is exposed. Once the plate-bearing test is completed, the repair of a test pit can be expensive and may keep the test area closed for several days.

Nondestructive tests are economical to perform and data can be collected at up to 250 locations per day. The NDT equipment measures pavement surface response (i.e., deflections) from an applied dynamic load that simulates a moving wheel. The magnitude of the applied dynamic load can be varied so that it is

CHAPTER 1. INTRODUCTION › 3. Limitations to NDT.

2 CHAPTER 1. INTRODUCTION

similar to the load on a single wheel of the critical or design aircraft. Pavement deflections are recorded directly beneath the load plate and at typical radial offsets of 12 in (30 cm), out to typical distances of 60 in (150 cm) to 72 in (180 cm).

The deflection data that are collected with NDT equipment can provide both qualitative and quantitative data about the strength of a pavement at the time of testing. The raw deflection data directly beneath the load plate sensor provides an indication of the strength of the entire pavement structure. Likewise, the raw deflection data from the outermost sensor provides an indication of subgrade strength.

In addition, when deflection or stiffness profile plots are constructed with deflection data from all test locations on a pavement facility, relatively strong and weak areas become readily apparent.

Quantitative data from NDT include material properties of each pavement and subgrade layer that engineers use with other physical properties, such as layer thicknesses and interface bonding conditions, to evaluate the structural performance of a pavement or investigate strengthening options. Most of the material property information is obtained using software programs that process and analyze raw NDT data. Once material properties, such as modulus of elasticity, E, and modulus of subgrade reaction, k, are computed, the engineer can conduct structural evaluations of existing pavements, design structural improvements, and develop reconstruction pavement cross-sections using subgrade strength data.

3 . Limitations to NDT. Although NDT has many advantages, it also has some limitations. NDT is a very good methodology for assessing the structural condition of an airfield pavement; however, engineers must use other methods to evaluate the functional condition of the pavement, for example, visual condition, smoothness, and friction characteristics. The visual condition is most frequently assessed using the PCI in accordance with American Society for Testing and Materials (ASTM) D 5340, Standard Test Method for Airport Pavement Condition Index Surveys, and AC 150/5380-6, Guidelines and Procedures for Maintenance of Airport Pavements. Once the NDT-based structural and functional conditions are known, the engineer can assign an overall pavement condition rating.

The differentiation between structural and functional performance is important in developing requirements for pavement rehabilitation. For example, a pavement can have a low PCI due to environmental distress, yet the pavement has sufficient thickness to accommodate structural loading. The converse may also be true, whereby a pavement may be in good condition, but has a low structural life due to proposed heavier aircraft loading.

In addition, while NDT may provide excellent information about structural capacity, the engineer may still require other important engineering properties of the pavement layers, such as grain-size distribution of the subgrade to determine swelling and heaving potential. For subsurface drainage evaluation and design, grain-size distribution and permeability tests may help assess the hydraulic capacity of the base, subbase, and subgrade.

It should also be noted that quantitative results obtained from raw NDT data are model dependent. The results depend on the structural models and software algorithms that are used by programs that process NDT data and perform a back-calculation of layer material properties.

Because of the model dependencies of NDT software analysis tools, the engineer should exercise caution when evaluating selected pavement types, such as continuously reinforced concrete pavement, posttensioned concrete, and pre-tensioned concrete. The structural theory and performance models for these pavement types are significantly different than traditional pavements, which include Asphalt Cement Hot Mix Asphalt (HMA), jointed plain Portland Cement Concrete (PCC), jointed reinforced PCC, HMA overlaid PCC, and PCC overlaid PCC.

Finally, NDT conducted at different times during the year may give different results due to climatic changes. For example, tests conducted during spring thaw or after extended dry periods may provide nonrepresentative results or inaccurate conclusions on pavement at subgrade strength.

CHAPTER 2. DESCRIPTION OF NDT PROCESS › 5. Pavement Stiffness and Sensor Response.

CHAPTER 2. DESCRIPTION OF NDT PROCESS 3

CHAPTER 2. DESCRIPTION OF NDT PROCESS

4 . General. NDT, using static or dynamic testing equipment, has proven useful in providing data on the structural properties of pavement and subgrade layers. The data are typically used to detect patterns of variability in pavement support conditions or to estimate the strength of pavement and subgrade layers. With this information, the engineer can design rehabilitation overlays and new/reconstructed crosssections, or optimize a rehabilitation option that is developed from an APMS.

This AC focuses on nondestructive testing equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement. NDT equipment that imparts dynamic loads creates surface deflections by applying a vibratory or impulse load to the pavement surface through a loading plate. For vibratory equipment, the dynamic load is typically generated hydraulically, as is the case for the Road Rater, or by counter rotating masses, as is the case for the Dynaflect. For impulse devices, such as the Falling Weight Deflectometer (FWD), the dynamic load is generated by a mass free falling onto a set of rubber springs, as shown in Figure 1. The magnitude of the impulse load can be varied by changing the mass and/or drop height so that it is similar to that of a wheel load on the main gear of an aircraft.

For both impulse and vibratory equipment, pavement response is typically measured by a series of sensors radially displaced from the loading plate, as shown in Figure 2. For static devices, such as the Benkleman Beam, a rebound deflection from a truck or other vehicle load is measured. Typically, the rebound deflection is measured only at the location of the load and not at the other radially spaced sensors shown in Figure 2.

5 . Pavement Stiffness and Sensor Response. The load-response data that NDT equipment measure in the field provides valuable information on the strength of the pavement structure. Initial review of the deflection under the load plate and at the outermost sensor, sensors D1 and D7 in Figure 2, respectively, is an indicator of pavement and subgrade stiffness. Although this information will not provide information about the strength of each pavement layer, it does provide a quick assessment of the pavement’s overall strength and relative variability of strength within a particular facility (runway, taxiway, or apron).

Figure 2: picture of page 10Figure 2 · page 10
Picture of the page from the copy saved here

Pavement stiffness is defined as the dynamic force divided by the pavement deflection at the center of the load plate. For both impulse and vibratory devices, the stiffness is defined as the load divided by the maximum deflection under the load plate. The Impulse Stiffness Modulus (ISM) and the Dynamic Stiffness Modulus (DSM) are defined as follows for impulse and vibratory NDT devices, respectively:

I(D)SM = L / do

Where:

I(D)SM = Impulse and Dynamic Stiffness Modulus (kips/in) L = Applied Load (kips) do = Maximum Deflection of Load Plate (in)

CHAPTER 2. DESCRIPTION OF NDT PROCESS › 6. Deflection Basin.

4 CHAPTER 2. DESCRIPTION OF NDT PROCESS

Figure 1. Impulse Load Created by FWD

Figure 2. Sensors Spaced Radially from the Load Plate

6 . Deflection Basin. After the load is applied to the pavement surface, as shown in Figure 1, the sensors shown in Figure 2 are used to measure the deflections that produce what is commonly referred to as a deflection basin. Figure 3 shows the zone of load influence that is created by a FWD and the relative location of the sensors that measure the deflection basin area. The deflection basin area can then be used to obtain additional information about the individual layers in the pavement structure that cannot be obtained by using deflection data from a single sensor.

The shape of the basin is determined by the response of the pavement to the applied load. The pavement deflection is the largest directly beneath the load and then decreases as the distance from the load

CHAPTER 2. DESCRIPTION OF NDT PROCESS 5

Figure 3: picture of page 11Figure 3 · page 11
Picture of the page from the copy saved here

increases. Generally, a weaker pavement will deflect more than a stronger pavement under the same load. However, the shape of the basin is related to the strengths of all the individual layers.

To illustrate the importance of measuring the deflection basin, Figure 4 shows a comparison of three pavements. Pavement 1 is PCC and pavements 2 and 3 are HMA. As expected, the PCC distributes the applied load over a larger area and has a smaller maximum deflection than the other two pavements. Although pavements 2 and 3 have the same cross- section and the same maximum deflection under the load plate, they would presumably perform differently under the same loading conditions because of the differences in base and subgrade strengths.

Figure 4: picture of page 12Figure 4 · page 12
Picture of the page from the copy saved here

In addition to each layer’s material properties, other factors can contribute to differences in the deflection basins. Underlying stiff or apparent stiff layers, the temperature of the HMA layer during testing, moisture contents in each of the layers, and PCC slab warping and curling can affect deflection basin shapes. An important component in the evaluation process, then, is analysis of the NDT data to estimate the expected structural performance of each pavement layer and subgrade.

Figure 3. Schematic of Deflection Basin

CHAPTER 2. DESCRIPTION OF NDT PROCESS › 7. Use of NDT Data.

6 CHAPTER 2. DESCRIPTION OF NDT PROCESS

Figure 4. Comparison of Deflection Basin of Three Pavements

7 . Use of NDT Data. There are many ways to use the NDT data to obtain those pavement characteristics that are needed to identify the causes of pavement distresses, conduct a pavement evaluation, or perform a strengthening design. Engineers can evaluate the NDT data using qualitative and quantitative procedures. Subsequent chapters present several methods that can be used to compute and evaluate such pavement characteristics as:

a. ISM, DSM, and normalized deflections.

b. Back-calculated elastic modulus of pavement layers and subgrade.

c. Correlations to conventional characterizations (for example, California Bearing Ratio [CBR], k).

d. Crack and joint load transfer efficiency.

e. Void detection at PCC corners and joints.

These NDT-derived pavement characteristics can then be used in the FAA’s evaluation and design procedures.

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT › 9. Categories of Equipment.

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT 7

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT

8 . General. This chapter introduces the various types of NDT equipment that are used to evaluate pavements. Although the AC focuses on NDT equipment, other types of nondeflection measuring equipment are introduced to illustrate how NDT data can be supplemented with other test data to improve the quality and reliability of the pavement evaluation.

9 . Categories of Equipment. Nondestructive testing equipment includes both deflection and nondeflection testing equipment. Deflection measuring equipment for nondestructive testing of airport pavements can be broadly classified as static or dynamic loading devices. Dynamic loading equipment can be further classified according to the type of forcing function used, i.e., vibratory or impulse devices. Nondeflection measuring equipment that can supplement deflection testing includes ground-penetrating radar, infrared thermography, dynamic cone penetrometer, and devices that measure surface friction, roughness, and surface waves.

a. Deflection Measuring Equipment. There are several categories of deflection measuring equipment: static, steady state (for example, vibratory), and impulse load devices. A static device measures deflection at one point under a nonmoving load. Static tests are slow and labor intensive compared to the other devices. Examples of a static device include the Benkleman Beam and other types of plate bearing tests.

Vibratory devices induce a steady-state vibration to the pavement with a dynamic force generator, as illustrated in Figure 5. As this figure shows, there is a small static load that seats the load plate on the pavement. The dynamic force is then generated at a precomputed frequency that causes the pavement to respond (deflect). The pavement deflections are typically measured with velocity transducers. There are several types of steady-state vibratory devices, including Dynaflect and Road Rater.

Figure 5: picture of page 13Figure 5 · page 13
Picture of the page from the copy saved here

Impulse load devices, such as the FWD or Heavy-Falling Weight Deflectometer (HWD), impart an impulse load to the pavement with free-falling weight that impacts a set of rubber springs, as illustrated in Figure 6. The time from A to B in this figure is the time required to lift the FWD weight package to the required drop height. The magnitude of the dynamic load depends on the mass of the weight and the height from which the weight is dropped.

Figure 5. Static and Dynamic Force Components for Vibratory NDT

8 CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT

FORCE EXERTED

ON PAVEMENT

25 - 30 MSEC

A B C

TIME (TIME FROM A TO B IS VARIABLE, DEPENDING ON DROP HEIGHT)

IMPULSE LOAD

Figure 6. Time to Peak Load for Impulse-Based NDT Equipment

Figure 6: picture of page 13Figure 6 · page 13
Picture of the page from the copy saved here

The resultant deflections are typically measured with velocity transducers, accelerometers, or linear variable differential transducers (LVDT). Table 1 provides a summary of the various types of static, vibratory, and impulse load NDT equipment that are in use or in production today. The most popular and widely used NDT equipment falls in the impulse-based category. This category of NDT equipment is used extensively for airport, road, and seaport pavement testing.

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT 9

Table 1. Summary of Nondestructive Testing Measuring Equipment

Category Equipment Manufacturer

Load Range, lb (kN)

Load Transmitted by,

in (cm)

Number of

Sensors

Sensor Spacing, in

(cm)

Static

Benkleman

Beam Soiltest Inc. Vehicle Dependent

Loaded Truck or

Aircraft 1 N/A

La Croix Deflectograph Switzerland Vehicle Dependent Loaded Truck 1 N/A

Plate Bearing

Test

Several, ASTM D1196

Vehicle Dependent Loaded Truck 1 N/A

Vibratory

Dynaflect Geolog, Inc. 1,000 (5) 15 (240) Diameter Steel Wheels 4 Variable,

0 - 48 (0 - 120)

Road Rater Foundations Mechanic, Inc.

500 - 8,000 (2 - 35)

18 (45) Diameter plate 4 - 7 Variable,

0 - 48 (0 - 120)

WES Heavy

Vibrator

U.S. Corps of

Engineers

500 - 30,000 (2 - 130)

12 or 18 (30 - 45) Diameter plate

5 Variable,

0 - 60 (0 - 120)

Impulse

Dynatest FWD Dynatest Engineering

1,500 - 27,000 (7 - 240)

12 – 18 (30 - 45) Diameter plate

7 - 9 Variable,

0 - 90 (0 - 120)

Dynatest HWD Dynatest Engineering

6,000 - 54,000 (27 - 240)

12 or 18 (30 - 45) Diameter plate

7 - 9 Variable,

0 - 96 (0 - 240)

JILS FWD Foundation Mechanics, Inc.

1,500 - 24,000 (7 - 107)

12 or 18 (30 - 45) Diameter plate

7 Variable

0 - 96 (0 - 240)

JILS HWD Foundation Mechanics, Inc.

6,000 - 54,000 (27 - 240)

12 or 18 (30 - 45) Diameter plate

7 Variable,

0 - 96 (0 - 240)

KUAB FWD KUAB

1,500 - 24,000 (7 - 150)

12 or 18 (30 - 45) Diameter plate

7 Variable,

0 – 72 (0 - 180)

KUAB HWD KUAB

6,000 - 54,000 (13 - 294)

12 or 18 (30 - 45) Diameter plate

7 Variable,

0 – 72 (0 - 180)

Carl Bro FWD Carl Bro Group

1,500 - 34,000 (7 - 150)

12 or 18 (30 - 45) Diameter plate

9 - 12 Variable,

0 – 100 (0 - 250)

Carl Bro HWD Carl Bro Group

1,500 - 27,000 (7 - 250)

12 or 18 (30 - 45) Diameter plate

9 - 12 Variable,

0 – 100 (0 - 250)

Carl Bro LWD Carl Bro Group

1,500 - 27,000 (1 - 15)

4 or 8 or 12 (30 - 45) Diameter plate

9 - 12 Variable,

0 – 40 (0 - 100)

Equipment mentioned above is for information purposes only.

10 CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT › 10. General Requirements for NDT Equipment.

b. Nondeflection Measuring Equipment. Several other types of nondestructive testing equipment are available that may assist the engineer in conducting a pavement evaluation, performing a pavement design, or implementing a pavement management system. The data that are collected from nondeflection measuring equipment often supplement NDT data or provide standalone information in pavement analysis work. While deflection data from NDT equipment are used primarily to evaluate the structural capacity and condition of a pavement, the following nondeflection measuring equipment can also be used:

(1) Ground-Penetrating Radar (GPR). The most common uses of GPR data include measuring pavement layer thicknesses, identifying large voids, detecting the presence of excess water in structure, locating underground utilities, and investigating significant delamination between pavement layers.

(2) Spectral Analysis of Surface Waves (SASW). SASW equipment provides data that can supplement NDT data. Unlike NDT equipment, which imparts much higher loads to the pavement, SASW equipment consists of small portable units that evaluate pavements from Rayleigh wave measurements that involve low strain levels. Engineers can then evaluate these data to compute the approximate thickness of pavement layers, layer modulus of elasticity values for comparison to NDT computed elasticity values, and approximate depth to rigid layers.

(3) Infrared Thermography (IR). One of the most common uses of IR data is to determine if delamination has occurred between asphalt pavement layers.

(4) Friction Characteristics. There are types of equipment that are available to conduct surface friction tests on a pavement. The methods of testing and several common types of friction testers for airports are addressed in AC 150/5320-12.

(5) Smoothness Characteristics. There are also several types of equipment that are available to collect surface profile data and to determine how aircraft may respond during taxi, takeoff, and landing.

(6) Dynamic Cone Penetrometer (DCP). A DCP is another piece of equipment that can be used to supplement NDT data. If cores are taken through the pavement to verify the thickness of an HMA or PCC layer, the DCP can help evaluate the stiffness of the base, subbase, and subgrade. Data are recorded in terms of the number of blows per inch that is required to drive the cone-shaped end of the rod through each of the layers. Plots of these data provide information about the changes in layer types and layer strengths.

1 0 . General Requirements for NDT Equipment. If deflection measuring equipment is being considered for use in a pavement study, the engineer should first evaluate project requirements. To provide meaningful results, several general requirements should be considered regarding equipment capabilities. The quality of the NDT results will depend on several factors, such as the quality of the test plan, test procedures, and data analyses procedures, as described in subsequent chapters of this AC.

In general, the value of NDT will be greater for primary transport airports compared to general aviation (GA) airports. However, if a GA airport supports, or will support, aircraft with a maximum gross takeoff weight greater than 30,000 lb (13,500 kg), or heavier are expected to use the airport on an infrequent basis, NDT may be useful in evaluating the pavement. Also, because of the increasing number of business jets that operate from reliever and GA airports, NDT may add significant value to a GA pavement study.

If nondestructive testing is indicated, the airport operator should consider the operational impacts of operating the equipment on the airside. While NDT equipment can collect data at many locations over a relatively short period of time, the airport may not be able to close a particular facility during peak periods of aircraft operations.

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT › 11. Static Devices.

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT 11

Depending on the frequency and types of NDT tests, the work on a typical runway that is 9,000 ft (2,800 m) long and 150 ft (45 m) wide normally takes 1 to 2 days. If peak traffic occurs during daylight hours, it may be more efficient to conduct the NDT at night when the facility can be closed for 6 to 8 hour periods.

If the sponsor and engineer decide to conduct NDT, they should carefully consider the type of equipment that will be used for the study. In general, the equipment should be capable of imparting a dynamic load to the pavement that creates deflections and loads that are large enough to be accurately recorded with the sensors on the pavement surface. The required magnitude of the dynamic load will depend primarily on the thickness and strength of the pavement layers. If the deflections are adequate for the structure and type of aircraft that will use the pavement, the NDT equipment sensors should provide accurate and repeatable deflection measurements at each sensor location.

Repeatability is important for two reasons. First, NDT may be conducted at multiple load levels to learn more about the pavement structure, such as whether voids exist or if the subgrade soil is stress sensitive and appears to get harder or softer with increasing load. To characterize the pavement properly, the sensors must accurately and consistently record deflection data. Second, because pavements deteriorate over time, subsequent pavement evaluation and NDT work may be important. To quantify the rate of deterioration, it is important to have reliable deflection data at different times during the pavement’s design life.

1 1 . Static Devices. The most common static device is the Benkleman Beam, although several other devices have been built to automate its use. Examples of automated beams include the Swedish La Croix Deflectograph; the British Transport and Road Research Laboratory Pavement Deflection Data Logging (PDDL), which is a modified La Croix Deflectograph; and Caltran’s California Traveling Deflectometer. Figure 7 shows a Benkleman Beam that has not been automated.

Figure 7: picture of page 17Figure 7 · page 17
Picture of the page from the copy saved here

Figure 7. Benkleman Beam

The Benkleman Beam measures the deflection under a static load, such as a truck or aircraft. The truck weight is normally 18,000 lb (200 kg) or a single axle with dual tires. The tip of the beam is placed between the dual tires and the rebound deflection is measured as the vehicle moves away from the beam.

The primary advantages that are associated with the Benkleman Beam are its simplicity and the numerous design procedures that have historically used beam data. Disadvantages to its use include longer testing

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT › 12. Vibratory Devices.

12 CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT

time and the lack of repeatability of results as compared with more modern devices. The Benkleman Beam also does not typically provide deflection basin data for back-calculation of pavement layer moduli.

1 2 . Vibratory Devices. Vibratory devices include the Dynaflect and the Road Rater.

a. Dynaflect. The Dynaflect, shown in Figure 8, is an electromechanical device for measuring dynamic deflection. It is mounted on a two-wheel trailer and is stationary when the measurements are taken. A 1,000-pound (5 kN) peak-to-peak sinusoidal load is applied through two rubber coated steel wheels at a fixed 8 Hz frequency. The counter-rotating masses produce a sinusoidal pavement deflection, which is recorded by velocity transducers.

Figure 8. Dynaflect Deflection Trailer

Figure 8: picture of page 18Figure 8 · page 18
Picture of the page from the copy saved here

Advantages of the Dynaflect include high reliability, low maintenance, and the ability to measure the deflection basin. A major disadvantage of the equipment is the low dynamic load amplitude, which is significantly less than normal aircraft loads. The relatively light load may not produce adequate deflections on heavy airport pavements and the back- calculated subgrade moduli may not be accurate. Therefore, the use of this device is only recommended for light load pavements serving aircraft less than 12,500 lb (5,670 kg).

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT › 13. Impulse Devices.

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT 13

b. Road Rater. The Road Rater, shown in Figure 9, also measures dynamic deflection using a sinusoidal force generated by a hydraulic acceleration of a steel mass. Several models are available that have peak-to-peak loading that ranges from a low of 500 lb (2 kN) to a high of 8,000 lb (35 kN). Pavement response is measured at the center of the loading plate and at radial offset distances using four to seven velocity transducers, depending on the model. The Road Rater can measure deflection basins, as well as dynamic response over a broad range of frequencies. It has a rapid data acquisition system and its wide use has resulted in the availability of large amounts of data on pavement response and performance. The major disadvantage of some models of the Road Rater is low force amplitude.

Figure 9. Road Rater

Figure 9: picture of page 19Figure 9 · page 19
Picture of the page from the copy saved here

1 3 . Impulse Devices. These devices measure deflection using a free-falling mass onto rubber springs to produce an impulse load. The magnitude of the calculated dynamic load and the resultant pavement deflections are recorded. Generally, these devices fall into one of two categories: FWD and HWD. Most impulse devices are classified as a HWD when they are able to generate a maximum dynamic load that is greater than 34,000 lb (150 kN).

There are several manufacturers of FWDs and HWDs, including KUAB America, Dynatest Group, Phoenix Scientific, Inc., Foundation Mechanics, Inc., and Viatest. These impulse devices all share several common advantages for this type of deflection measuring equipment. The FWD and HWD are believed to better simulate moving wheel loads, can measure the extent of the deflection basin, have relatively fast data acquisition, and require only a small preload on the pavement surface. The disadvantages of the equipment are minimal and related more to the overall systems and different pulse durations used on different models. Table 2 provides a detailed summary of the impulse equipment specifications.

14 CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT

Table 2. Detailed Specifications for Selected FWDs and HWDs

Dynatest Foundation Mechanics, Inc. KUAB Carl Bro Group

Load Range,

lb (kN)

1,500 - 54,000 (7 - 240)

1,500 - 54,000 (7 - 240)

1,500 - 66,000 (7 - 300)

1,500 - 56,000 (7 - 250)

Load Duration,

milliseconds 25 - 30 ms Selectable 56 ms 25 - 30 ms

Load Rise Time Variable Selectable 28 millisecond 12 - 15 ms

Load Generator One-mass Two-mass One-mass One-mass

Type of Load

Plate

Rigid with rubberized

pad or split plate

Rigid with rubberized

pad

Segmented or nonsegmented with

rubberized pads

Four segmented plate

with rubberized pad

Diameter of

Load Plate,

in (cm)

12 and 18 (30 and 45)

12 and 18 (30 and 45)

12 and 18 (30 and 45)

12 and 18 (30 and 45)

Type of Deflection

Sensors

Geophones with or

without dynamic calibration device

Geophones

Seismometers with static field calibration

device

Geophones with or

without dynamic calibration device

Deflection

Sensor Positions,

in (cm)

0 - 90 (0 - 225)

0 - 96 (0 - 240)

0 - 72 (0 - 180)

0 - 96 (0 - 250)

Number of

Sensors 7 - 9 7 7 9 - 12

Deflection Sensor Range,

mils (mm)

80 or 100 (2 or 2.5 mm) 80 (2) 200 (5) 90 (2.2)

Deflection Resolution 1 im (0.04 mils) 1 im (0.04 mils) 1 im (0.04 mils) 1 im (0.04 mils)

Relative Accuracy of

Deflection

Sensors

2 µm ± 2% 2 µm ± 2% 2 µm ± 2% 2 µm ± 2%

Test Time

Required (four loads)

25 seconds 30 seconds 35 seconds 20 seconds

Type of Computer Personal computer Personal computer Personal computer Personal computer

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT 15

a. KUAB America. KUAB manufactures a FWD (Figure 10) and HWD, which include five models with load ranges up to 66,000 lb (290 kN). The load is applied through a two-mass system, and the resultant dynamic response is measured with seismometers and LVDT through a mass-spring reference system. The load plate is segmented to provide a uniform pressure distribution to the pavement.

Figure 10. Kuab FWD

b. Dynatest Group. Dynatest manufactures both a FWD (Figure 11) and a HWD with models that generate dynamic loads up to 54,000 lb (240 kN). The weights are dropped onto a rubber buffer system. Seven to nine velocity transducers are then used to measure the load and dynamic response.

Figure 11. Dynatest FWD

16 CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT

Figure 10: picture of page 21Figure 10 · page 21
Picture of the page from the copy saved here

c. Carl Bro Group. Carl Bro manufactures a FWD and a HWD generating dynamic loads up to 56,000 lb (250 kN). Furthermore, Carl Bro manufactures the portable FWD (LWD) – PRIMA 100 – for on-site measurement and analysis of collected data, shown in Figure 12. All equipment types are moduledesigned. With PRI models, this means that it is possible to move the measuring equipment from a trailer chassis into a van and to upgrade from 7-150 kN to 7-250 kN. With PRIMA 100, this means that one or two additional geophones can be connected depending on the work to be performed and wireless and GPS operation. The LWD uses one to three velocity transducers and FWD and HWD equipment uses 9 - 12 velocity transducers to measure load and dynamic response. Weights are dropped on a rubber buffer system and the load plates are four-split allowing maximum contact to the surface measured upon.

Figure 12. Carl Bro FWD/HWD and LWD Trailer, Van-Integrated or Portable

Figure 12: picture of page 22Figure 12 · page 22
Picture of the page from the copy saved here

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT › 14. Use of Historical Data.

CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT 17

d. Foundation Mechanics, Incorporated. Foundation Mechanics also manufactures a JILS FWD and a JILS HWD (Figure 13) that generate loads from 1,500 lb (7 kN) to 54,000 lb (240 kN). The FWD and HWD use two mass elements and a four-spring set combination to impose a force impulse in the shape of a half-sine wave. Load magnitude, duration, and rise time are dependent on the mass, mass drop height, and arresting spring properties. Seven velocity transducers are typically used to measure the dynamic response.

Figure 13. JILS HWD

1 4 . Use of Historical Data. Although impulse deflection measuring equipment is widely used in the pavement industry, vibratory and static equipment are still in operation, and extensive amounts of data using these devices have been collected over many years. Since historical data are important in a pavement study, Chapter 7 discusses how those data, or data from older devices, can be used in the pavement study.

18 CHAPTER 3. NONDESTRUCTIVE TESTING EQUIPMENT

Intentionally Left Blank

Figure 13: picture of page 23Figure 13 · page 23
Picture of the page from the copy saved here

CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT › 16. Need for Standardization.

CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT 19

CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT

1 5 . General. This chapter addresses key issues that an airport operator or engineer should consider when selecting or approving a specific NDT device for an airport pavement study. The FAA does not have an approved list of deflection measuring equipment but does want to ensure that standards are established for the collection of deflection data.

1 6 . Need for Standardization. The analysis of raw deflection data can lead to varying conclusions regarding the strength of a pavement. Therefore, it is important to ensure that deflection data are consistent and repeatable among the various types of equipment within the static, vibratory, and impulse NDT categories. Because of Federal participation in pavement studies, the FAA must have standards to ensure reliable data collection.

A valuable benefit of NDT data is the ability to record relative variations in pavement strength between test locations. Variations in pavement strength are typically the result of variations in layer thicknesses and strength, temperature susceptibility of paving materials, seasonal effects, water table heights, frost depths, and NDT equipment itself.

This chapter provides guidance on standardization for the various components of deflection measuring equipment so equipment or test variance can be minimized. Table 3 provides ASTM references for the equipment categories addressed in this AC. As previously described, the most common type of NDT equipment in use today is the impulse load device, (i.e., FWD or HWD). ASTM D 4694, Standard Test Method for Deflections with a Falling-Weight-Type Impulse Load Device, addresses key components of this device, which include instruments exposed to the elements, the force-generating device (for example, falling weight), the loading plate, the deflection sensor, the load cell, and the data processing and storage system.

Table 3. ASTM Standards for Deflection Measuring Equipment

ASTM

NDT Equipment Type

Static Vibratory Impulse

D 1195, Standard Test Method for Repetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements

●

D 1196, Standard Test Method for Nonrepetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements

●

D 4602, Standard Guide for Nondestructive Testing of Pavements Using Cyclic-Loading Dynamic Deflection Equipment ●

D 4694, Standard Test Method for Deflections with A Falling-Weight- Type Impulse Load Device ●

D 4695, Standard Guide for General Pavement Deflection Measurements ● ● ●

Calibration of the equipment is very important to ensure accurate recordation of deflection data. ASTM D 4694 recommends the following calibration schedule for the impulse load device:

CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT › 17. FAA Sensitivity Study.

20 CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT

a. Force-Generating Device (prior to testing or other component calibration). This calibration involves preconditioning the device by dropping the weight at least five times and checking the relative difference in each loading.

b. Deflection Sensors (at least once a month or as specified by the manufacturer). During this calibration, the deflection measurements for each sensor are adjusted so they will produce the same deflection measurement within the precision limits of the sensors, as specified by the manufacturer.

1 7 . FAA Sensitivity Study. Assuming the NDT device is correctly calibrated and functioning properly, the engineer or equipment operator will make several decisions concerning testing options for the deflection measuring equipment.

a. Load Plate Diameter. Many impulse-loading equipment manufacturers offer the option of a 12in (30 cm) or an 18 in (45 cm) diameter load plate. There are several important factors that should be considered when selecting the load plate size for a pavement study, including the following:

(1) Most Common Plate Size—It is much easier to evaluate NDT data if all the data has been collected using one plate size. Most analysis software has been written for both 12 in (30 cm) and 18 in (45 cm) plate sizes.

(2) Pavement Layer Compression—A larger load plate has the advantage of distributing the impulse load over larger areas and minimizing the amount of layer compression. The importance of the plate size depends on the magnitude of the load, surface temperature, and if the surface layer consists of unbound or bounded material. Since most NDT work is conducted on HMA and PCC surfaces when the pavement is not extremely hot, compression is generally not a significant concern. However, if NDT is conducted on an unbound granular base, subbase, or subgrade, the larger plate may be more advantageous.

(3) Plate Seating on Pavement Surface—If the surface of the pavement is very rough, the larger plate may not seat properly on the surface and cause a nonuniform distribution of the impulse load. A segmented load plate helps mitigate the effects of a rough surface.

(4) Summary—The 12 in (30 cm) load plate is normally used when testing on bound surface materials. If NDT is to be performed on unbound base, subbase, or subgrade materials an 18 in (45 cm) load plate should be used. If the manufacturer does not provide the larger load plate, the engineer can use the smaller load plate, but should rely more on the deflection sensors away from the load plate.

b. Sensor Spacing and Number. The number of available sensors depends on the manufacturer and equipment model. As a result, the sensor spacing will depend on the number of available sensors and the length of the sensor bar. Although most NDT equipment allows for the sensors to be repositioned for each pavement study, it is desirable to conduct NDT work using the same configuration, regardless of the type of pavement structure.

Table 4 shows common sensor configurations that are used by various agencies. In general, those NDT devices that have more sensors can more accurately measure the deflection basin that is produced by static or dynamic loads. Most agencies prefer to limit the distance between sensor spacing to no more than 12 in (30 cm). The exception is the seventh sensor in the Strategic Highway Research Program (SHRP) configuration, where there are 24 in (60 cm) between the sixth and seventh sensors.

Accurate measurement of the deflection basin is especially important when analyzing the deflection data to compute the elastic modulus of each pavement layer. However, it is also very important to ensure that the magnitude of deflection in the outermost sensor is within the manufacturer’s specifications for the sensors. The magnitude of the deflection in the outermost sensor depends primarily on the magnitude of the dynamic load, the thickness and stiffness of the pavement structure, and the depth to an underlying rock or stiff layer.

CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT 21

Table 4. Common Sensor Configurations

Agency Configuration

Name

Sensor Distance from Center of Load Plate, in (cm)

Sensor 1 Sensor 2 Sensor 3 Sensor 4 Sensor 5 Sensor 6 Sensor 7

U.S. Air Force AF 7-Sensor 0 12 (30)

24 (60)

36 (90)

48 (120)

60 (150)

72 (180)

FHWA and

State DOT

SHRP 4-

Sensor 0 12 (30)

24 (60)

36 (90)

SHRP 7-

Sensor 0 6 (15)

12 (30)

18 (45)

24 (60)

36 (90)

60 (150)

c. Pulse Duration. For impulse-load NDT equipment, the force-pulse duration is the length of time between an initial rise in the dynamic load until it dissipates to near zero. Both the FAA and ASTM recognize a pulse duration in the range of 20 to 60 milliseconds as being typical for most impulse-load devices. Likewise, rise time is the time between an initial rise in the dynamic load and its peak before it begins to dissipate. Typical rise times for impulse-load devices are in the range of 10 to 30 milliseconds.

d. Load Linearity. During the analysis of deflection data, engineers often assume that all layers in the structure respond in a linear elastic mode. For example, this means that a 10-percent increase in the magnitude of the dynamic load from the NDT device will lead to a 10-percent increase in the response to the dynamic load increase. For most pavement structures and testing conditions, traditional paving materials will behave in a linear elastic manner within the load range that the tests are conducted.

At the NAPTF, the FAA studied the response of the flexible pavement test items. The test sections included flexible pavement on aggregate and stabilized bases that were constructed on low-, medium-, and high-strength subgrade. The FAA tested each test section using HWD loads of 12,000 lb (50 kN), 24,000 lb (107 kN), and 36,000 lb (160 kN).

Figure 14 and Figure 15 show the linear behavior of the HMA test sections in terms of the ISM and backcalculated subgrade elastic modulus. The procedures for back-calculation of the subgrade modulus are discussed in Chapter 7. For the ISM and computed subgrade modulus, results of the sensitivity study showed there is little difference in the pavement response when the HWD impulse load is changed, provided the measured deflections are within the specified limits of the sensors. A linear response was also observed when the FAA conducted similar tests on the instrumented PCC runway test section at Denver International Airport (DIA), CO.

Figure 14: picture of page 28Figure 14 · page 28
Picture of the page from the copy saved here

Based on the results from the sensitivity studies at the NAPTF and DIA, the amplitude of the impulse load is not critical provided the generated deflections are within the limits of all deflection sensors. The key factors that will determine the allowable range of impulse loads are pavement layer thicknesses and material types. Thus, unless the pavement is a very thick PCC or HMA overlaid PCC structure, most FWD devices will be acceptable since they will be able to generate sufficient deflections for reliable data acquisition.

Generally, the impulse load should range between 20,000 lb (90 kN) and 55,000 lb (250 kN) on pavements serving commercial air carrier aircraft, provided the maximum reliable displacement sensor is not exceeded. Lighter loads may be used on thinner GA pavements.

CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT › 18. Summary of FAA Policy.

22 CHAPTER 4. REQUIREMENTS FOR NONDESTRUCTIVE TESTING EQUIPMENT

Figure 14. Evaluation of HWD Force Linearity in Terms of ISM

Figure 15. Evaluation of HWD Force Linearity in Terms of Subgrade Elastic Modulus

1 8 . Summary of FAA Policy. This section provides guidance on the equipment options that are associated with most types of deflection measuring equipment. Proper configuration of the NDT device regarding load plate size, sensor number and spacing, and impulse load magnitudes will ensure that consistent, reliable, and reusable deflection data can be recorded with the equipment. Before mobilizing to the field, the engineer should develop an NDT test plan, as described in Chapter 5, that can be properly executed, as described in Chapter 6.

Figure 15: picture of page 28Figure 15 · page 28
Picture of the page from the copy saved here

CHAPTER 5. TEST PLANNING › 20. Justification for NDT.

CHAPTER 5. TEST PLANNING 23

CHAPTER 5. TEST PLANNING

1 9 . General. Chapter 4 presented several equipment options for various NDT devices. This chapter discusses how to prepare an NDT plan before mobilizing to the field. Chapter 6 focuses on executing that NDT plan in the field. Together, all three chapters stress the importance of standardization so the deflection data that is recorded in the field is consistent, repeatable, and reliable. Data collection methods that meet these requirements will help ensure that future deflection data for the same pavement section can be compared to previous results to determine how quickly the pavement may be deteriorating at various stages of its design life.

2 0 . Justification for NDT. Before developing an NDT test plan, the airport operator and engineer should decide if the current situation warrants the collection of deflection data. Visual condition surveys, such as the PCI procedure, provide excellent information regarding the functional condition of the pavement. However, visual distress data can only provide an indirect measure of the structural condition of the pavement structure. Nondestructive testing combined with the analytical procedures described herein can provide a direct indication of a pavement’s structural performance.

Many commercial hub airports have fleet mixes that contain heavy narrow- and wide-body aircraft at a significant number of annual departures. The potential for structural damage typically depends on the number of annual departures and the maximum gross takeoff weights (MGTOW) of aircraft exceeding 100,000 lb (45,000 kg).

On the other end of the scale, most GA airports do not support routine operation of aircraft with MGTOW exceeding 60,000 lb (27,000 kg). However, there are scenarios where one or two departures of a heavy aircraft could cause significant damage to the pavement structure. Therefore, the ability to evaluate whether the pavement can accommodate occasional overload situations significantly benefit airport operation. Also, many GA airports service high tire pressure corporate jet operations of 20,000 lb (9,000 kg) to 60,000 lb (27,000 kg) that could justify an NDT program.

Once the airport operator and engineer have decided to include NDT in their pavement study, they should focus on the number and types of tests that will be conducted. The total number of tests will depend primarily on three factors:

a. The area of the pavements to be included in the study.

b. The types of pavement.

c. The type of study, which is typically referred to as a project or network-level investigation.

Project-level investigations refer to studies that are conducted in support of pavement rehabilitation, reconstruction, and new construction designs. Network-level studies generally support the implementation and updates of pavement management systems. The frequency of the NDT is greater in a project-level study that may typically include only one or two pavement facilities. This is in contrast to a network-level study, which may include all airside pavements, all landside pavements, or both.

CHAPTER 5. TEST PLANNING › 22. NDT Test Types.

24 CHAPTER 5. TEST PLANNING

2 1 . NDT Test Objectives. The objective of the NDT program is to collect deflection data that will support the objectives of a project or network-level pavement study. The data should be collected efficiently with minimal disruption to aircraft or vehicle traffic operations on the airside and landside of an airport. The NDT test plan should support the project and network-level objectives, which can be categorized as follows:

a. Project-Level Objectives:

(1) Evaluate the load-carrying capacity of existing pavements.

(2) Provide material properties of in-situ pavement layers for the design of pavement rehabilitation alternatives, which include restoration, functional and structural overlays, partial reconstruction (for example, runway keel), and complete reconstruction.

b. Network-Level Objectives:

(1) Supplement PCI survey data that may be stored in an APMS database for those scenarios where the NDT data will lead to the development of a multiyear Capital Improvement Program (CIP).

(2) Generate Pavement Classification Numbers (PCN) for each airside facility in accordance with AC 150/5335-5.

2 2 . NDT Test Types. There are several types of tests that may be conducted during a pavement study. For all types of pavements, the most common test is a center test. For jointed PCC and HMA overlaid PCC pavements, this is a test in the center of the PCC slab. For HMA pavements, this is a test in the center of the wheel path away from any cracks that may exist. The center test serves primarily to collect deflection data that form a deflection basin that can be used to estimate the strength of the pavement and subgrade layers.

For PCC and HMA overlaid PCC pavements, there are several other types of tests that will help characterize the structure. All of these tests focus on the fact that most PCC pavements have joints and most HMA overlaid PCC pavements have surface cracks that have reflected up from PCC joints. NDT at various locations on the joints, as shown in Figure 16, provides data regarding pavement response to aircraft loads and changes in climatic conditions.

Figure 16: picture of page 30Figure 16 · page 30
Picture of the page from the copy saved here

Figure 16. NDT Test Locations within a PCC Slab

CHAPTER 5. TEST PLANNING 25

Testing at longitudinal and transverse joints shows how much of an aircraft’s main gear is transferred from the loaded slab to the unloaded slab, as shown in Figure 17. As the amount of load transfer is increased to the unloaded slab, the flexural stress in the loaded slab decreases and the pavement life is extended. The amount of load transfer depends on many factors, including pavement temperature, the use of dowel bars, and the use of a stabilized base beneath the PCC surface layer.

Figure 17: picture of page 31Figure 17 · page 31
Picture of the page from the copy saved here

CHAPTER 5. TEST PLANNING › 23. Test Locations and Spacing.

Figure 17. Load Transfer across A PCC Joint

Corner testing is another common location to test, as shown in Figure 16. This is an area where a loss of support beneath the PCC slab occurs more often than other areas in the slab. Voids or a loss of support generally first occur in the slab corner because this is where deflections are the greatest in a PCC slab.

Therefore, if concrete slabs have corner breaks there is a possibility that voids exist. Corner slab testing on uncracked slabs in the area would be important in this case. Often, concrete midslab, joint, and corner tests are performed on the same slab to evaluate the relative stiffness at different locations.

2 3 . Test Locations and Spacing. Once the types of NDT have been selected, the next step is to select the location and testing interval for each pavement facility. Depending on the operating conditions and types of tests, the NDT operator can typically collect deflection data at 150 to 250 locations per 8hour shift.

While NDT will provide much better coverage of the pavement than destructive testing (for example, bores and cores), a balance should be obtained between coverage, cost, and time.

Table 5 provides general guidance on the spacing and location of testing for taxiways and runways. The offset recommendations are based on an assumed longitudinal joint spacing of approximately 18 ft (6 m) for PCC pavements. The offset distance refers to the distance from the taxiway and runway centerline. The third offset distances of 60 ft (18 m) and 65 ft (20 m) are applicable for runways that are wider than 125 ft (38 m). Table 6 provides general guidance on the frequency and location of testing for aprons.

The total number of tests for each facility should be evenly distributed in a grid. Each adjacent NDT pass in the grid should be staggered to obtain comprehensive coverage. For testing of airside access roads, perimeter roads, and other landside pavement, the recommendations provided in ASTM D 4695, Standard Guide for General Pavement Deflection Measurements, should be followed. This ASTM standard refers to network level testing as “Level I” and project level testing as “Level II” and “Level III.”

26 CHAPTER 5. TEST PLANNING

Table 5. Typical Runway and Taxiway Test Locations and Spacing, Feet (m)

Test Type

Jointed PCC and HMA Overlaid PCC HMA

Project Level Network Level Project Level Network Level

Offset

ft (m)

Spacing

ft (m)

Offset

ft (m)

Spacing

ft (m)

Offset

ft (m)

Spacing

ft (m)

Offset

ft (m)

Spacing

ft (m)

Center

10 (3) 30 (9) 65 (20)

100 (30) 100 - 200 (30 - 60) 400 (120)

10 (3) 200 - 400 (60 - 120)

200 - 400 (60 - 120)

100 (30) 100 - 200 (30 - 60) 200 - 400 (60 - 120)

10 (3) 200 - 400 (60 - 120)

Tran.

Joint

10 (3) 30 (9) 65 (20)

100 - 200 (30 - 60) 200 - 400 (60 - 120) 400 (120)

10 (3)

Long.

Joint

20 (6) 40 (12) 60 (18)

200 (60) 400 (120) 400 (120)

Corner

20 (6) 40 (12) 60 (18)

200 (60) 400 (120) 400 (120)

For each centerline offset, there are two NDT passes, one to the left and one to the right; spacing is staggered between adjacent NDT passes; and a minimum of two NDT tests should be conducted per pavement section.

Table 6. Typical Apron Test Locations and Frequency

Test Type

Jointed PCC and HMA Overlaid PCC HMA, Sq Ft (Sq M)

Project Level Network Level Project Level Network Level

Center 1 test for every 10 - 20 slabs 1 test for every 30 - 60 slabs

1 test for every 1,970 - 4,000 (600 - 1200)

1 test for every 5,750 – 11,490 (1750 to 3,500)

Transverse

Joint

1 test for every 10 - 40 slabs 1 test for every 60 slabs

Longitudinal

Joint

1 test for every 20 - 40 slabs 1 test for every 60 slabs

Corner 1 test for every 20 - 40 slabs

CHAPTER 5. TEST PLANNING › 24. NDT Test Sketches.

CHAPTER 5. TEST PLANNING 27

2 4 . NDT Test Sketches. Once the test types, locations, and spacing have been established for the pavement study, the next step is to prepare a sketch, such as those shown in Figure 18, Figure 19, and Figure 20 that clearly shows this information. In addition, the test plan should show the beginning station for each test facility and the direction of travel. Absent an airport wide stationing plan, the low-number end of a runway (for example, end 16 of RW 16-34) can be established as NDT Station 0+00.

Figure 18. Example Runway or Taxiway Sketch When Centerline Lies on Slab Joint

Note the first number indicates PCC lane number and the second number indicates a location within a lane (for example, along slab center or slab joint).

Figure 19. Example Runway or Taxiway Sketch When Centerline Does Not Lie on Slab Joint

Note the first number indicates PCC lane number and the second number indicates a location within the lane (for example, along slab center or slab joint).

28 CHAPTER 5. TEST PLANNING

Figure 20. Example Runway or Taxiway Sketch for HMA Pavements

Figure 18: picture of page 33Figure 18 · page 33
Picture of the page from the copy saved here

Note the first number indicates the HMA lane number and second number indicates a “center” test for HMA pavements.

The figures show ways to standardize the deflection recording process in the field. For example, the centerline joint in Figure 18 is annotated as joint “9.2” and the centerline in Figure 19 is noted as “Lane 9.”

The figures provide one example of how to develop an NDT sketch so that the engineer and NDT equipment operator can efficiently obtain deflection data in the field and minimize potential errors or misunderstandings. In addition to the test lane nomenclature, the engineer should also develop standard designations for each type of test that will be conducted. Standardizing is very important since each type of data should be grouped for analysis, as discussed in Chapter 7. An example of numerical designations or coding that could be used for HMA, PCC, and HMA overlaid PCC pavements are:

a. Center of PCC slab and HMA

b. Transverse joint

c. Longitudinal joint

d. Corner

e. Transverse crack

f. Longitudinal crack

Figure 19: picture of page 33Figure 19 · page 33
Picture of the page from the copy saved here

CHAPTER 5. TEST PLANNING › 25. Special Considerations.

CHAPTER 5. TEST PLANNING 29

2 5 . Special Considerations. It is important to consider how the climate and weather will affect NDT results. In northern climates, NDT is generally not conducted during the winter if frost has penetrated into the base, subbase, or subgrade. In addition, spring thaw represents a seasonal period when the pavement may be very weak for a short period of time. While it may be beneficial to know the strength of the pavement during spring thaw, it does not represent the typical strength of that structure throughout the year. Therefore, if deflection data are not going to be collected more than once, the engineer should select a test period that best represents the strength of the pavement for a majority of the year.

For both HMA and PCC pavements, NDT should not be conducted near cracks unless one of the test objectives is to measure load transfer efficiency across the crack. For HMA pavements, NDT passes should be made so that deflection data are at least 1.5 ft (0.5 m) to 3 ft (1 m) away from longitudinal construction joints.

Another concern for NDT work on PCC pavements is slab curling. Slab curling occurs when the corner or the center of the slab lifts off of the base due to differences in temperature between the top and bottom of the slab. As shown in Figure 21, the slab corners may lift off the base during nighttime curling, while the slab center and midjoints may lift off during daytime curling. The amount of curling depends primarily on joint spacing, PCC layer thickness, temperature differential between the bottom and top of the slab, and the stiffness of the base.

Figure 21. Thermal Curling in PCC Slab from Temperature Changes

It is important for engineers to be aware of possible curling so they are not confused by the results when they are attempting to conduct a void analysis. Voids, or loss of support, may occur from temperature curling, moisture warping, or erosion of the base. In most instances, the engineer is attempting to determine if voids exist because of erosion, consolidation, or expansive soils. As discussed in Chapter 7, for this purpose, engineers should conduct NDT at a time when the temperature is relatively constant between the day and night.

Finally, NDT test plans should consider that several analysis procedures require more than one test per location. Void analysis techniques generally require at least three load levels at each location. Likewise, if there is concern about stress sensitivity of the subgrade, multiple tests at different load levels will also be needed.

30 CHAPTER 5. TEST PLANNING

Intentionally Left Blank

CHAPTER 6. TEST PROCEDURES › 27. Equipment Mobilization.

CHAPTER 6. TEST PROCEDURES 31

CHAPTER 6. TEST PROCEDURES

2 6 . General. Chapter 5 presented guidelines for the development of a NDT plan that will meet the objectives of project-level or network-level studies. If the NDT equipment is properly configured, as discussed in Chapter 4, and a comprehensive NDT plan has been developed, the last step in the collection of the raw deflection data is to mobilize to the airport and safely conduct the NDT work. To ensure that quality data are collected in accordance with the NDT plan, the equipment operator should follow several procedures, as described below.

2 7 . Equipment Mobilization. Prior to mobilizing to the field site, the equipment operator should run through a pre-departure checklist, one designed for use with all NDT projects. The following list highlights several key items that should appear on the checklist:

a. Airport management notified and facility closures coordinated with Airport Operations staff.

b. Appropriate aircraft security and access security clearances obtained.

c. A copy of the NDT test plan and sketch.

d. An airport map with access roads and gates shown.

e. A check of airport identifiers and radio frequencies.

f. An airport layout plan with all pavements and facilities labeled.

g. A list of key airport personnel and their telephone numbers.

h. Pavement construction history reports.

i. Verification that all badging requirements have been met.

j. Properly configured deflection sensors.

k. Equipment and supplies:

(1) Beacon and flag.

(2) Spray paint for marking key locations.

(3) NDT equipment spare parts.

(4) Radios.

(5) Small drill for temperature holes.

(6) Safety vests.

(7) Equipment lights for nighttime testing.

l. 24-Hour “go-no-go” checks:

(1) Weather acceptable.

(2) NDT equipment checks.

m. Load cell and deflection sensor calibration in check.

Within 24 hours of mobilization, the operator should check to see that weather en route and at the project site is acceptable. In addition, the operator should conduct tests using the anticipated loads in accordance with the test plan. A nondestructive testing device is a high-technology piece of equipment that often requires maintenance and repair. It is much better to discover mechanical problems prior to setting off for the job site.

CHAPTER 6. TEST PROCEDURES › 29. Data Collection.

32 CHAPTER 6. TEST PROCEDURES

2 8 . Startup Operations. Equipment preparation for the start of data collection should be accomplished prior to accessing the Airport Operations Area (AOA). The equipment operator should develop the checklist and reuse it for each NDT project. The following checklist includes some items that should be addressed prior to entering the AOA:

a. Has air traffic control been contacted to verify testing schedule?

b. If required, have escorts been contacted?

c. Are badges properly displayed?

d. Are all supplies readily available?

e. Are radios working?

f. Are copies of the NDT plan, maps, and contact telephone numbers on hand?

g. Has the NDT equipment been run to ensure it is working correctly?

Conducting these operations prior to entering the AOA has several advantages. Most importantly, the NDT equipment will be ready to collect deflection data as soon as it is allowed on the AOA. It also demonstrates to air traffic control that preparations have been made to operate on the airside and collect data as quickly, safely, and efficiently as aircraft traffic operations will permit. Finally, if minor maintenance or repair work is required, better lighting conditions will exist outside the AOA if the work is being done at night.

2 9 . Data Collection. Deflection data may be collected under several operational scenarios. The NDT operator may be working on a small, uncontrolled GA airport or on a large commercial hub airport. Most large commercial airports require the NDT operator to be escorted and may issue a Notice to Airmen (NOTAM) to close very busy facilities, such as a primary runway. Small airports, such as relievers, may allow the NDT operator to collect deflection data on a “give way” basis during slow traffic periods. The operator must be prepared to work under all conditions in a safe and efficient manner.

a. Industry Standards. The references in Table 3 provide guidance on field testing procedures. Key field testing issues that are addressed in these documents include sensor accuracy and repeatability, recording of time and test locations, and measurement of pavement temperature

b. Orientation Photos. Prior to the start of testing on a pavement facility, the operator should spraypaint test lane (PCC) and pass (HMA) locations at Station 0+00. Each lane and pass should be at the centerline offsets or grid locations specified in the NDT test plan. If the offsets need to be adjusted or other elements of the plan need to be modified, the NDT operator should carefully note the changes and reasons for the changes. After Station 0+00 and test lanes have been marked, the operator should photograph or video tape the markings and an overview of the pavement facility, including typical surface distresses.

c. Record and Monitor Pavement Temperature. A pavement’s response under load is often temperature dependent. This is especially true for HMA pavements where the modulus of elasticity may change dramatically as the temperature changes. Also, load transfer across a non-doweled joint on a PCC pavement may also change significantly with a change in temperature.

A good location to monitor the mid-depth temperature of an HMA or PCC surface layer is at Station 0+00. A hole large enough to accommodate a thermometer can be drilled by the operator and filled with oil to record temperatures every two hours or as necessary. This location should be marked with spray paint so the operator can easily find the temperature hole prior to starting NDT on the next lane or pass. Air and pavement surface temperatures should also be recorded, hourly.

CHAPTER 6. TEST PROCEDURES 33

d. Selection of Input Force. The NDT test plan should estimate the magnitude of the dynamic load for the vibratory or impulse equipment. However, one of the first checks that the operator should make is to ensure the pre-selected loads are generating deflections that are within the manufacturer-specified limits of the sensors, as discussed in Chapter 4. If multiple tests are being conducted at each location at different force levels, the operator should ensure that all load levels produce deflections within the sensor limits.

The NDT operator may have to adjust the load levels throughout the data collection work if the pavement types and thicknesses vary significantly. Given the anticipated variation in pavement structures, the operator should select intermediate load levels that will generate deflections that are large enough for thick pavements, but not too large for thin structures. If the range of deflections is within the limits of the sensor accuracy, the testing operations will be more efficient and potential errors that may occur through reconfiguration of the NDT device and operating software will be minimized. In addition, NDT work at large commercial airports may require movement from one pavement facility to another prior to completion of testing on a particular facility to accommodate air traffic control directives. An intermediate load-level configuration will be especially beneficial in this situation.

e. Recording Deflection Measurements. Once proper input force levels have been established, the operator can begin collecting deflection data in accordance with NDT test plan. The NDT operation software that is used to record test data should allow the operator to record the following information, in addition to the input force and sensor deflections:

(1) Configuration setup (for example, sensor spacing, load plate size, and project description).

(2) Air, pavement surface, and surface layer mid-depth temperatures.

(3) Optional comments about pavement condition at a test location.

(4) Test location, as discussed in Chapter 5 and depicted on Figure 18 and Figure 20.

(a) Station (automatically recorded with most software).

(b) Lane (PCC) or pass (HMA) number (for example, 1.X).

(c) Location within each PCC lane (for example, X.1 or X.2 for center or joint).

(d) Location within each PCC slab (for example, 2 for transverse joint)

If the equipment operating software allows this information to be recorded and a comprehensive test plan has been developed, the data can be efficiently processed to allow comprehensive evaluation of results. If data analysis software is available, the NDT operator should record all deflection data for a pavement facility in a single file. The NDT operator should use a file naming nomenclature that allows the engineer to quickly understand what data are in the file, such as “RW12_30” for Runway 12-30. Before the NDT equipment is shut down for the day, the operator should back up all NDT data files on the laptop computer.

f. Monitoring Deflection Data. It is very important for the NDT operator to continuously monitor the data. In addition to the mirrors on a towing vehicle, most NDT devices are equipped with a monitor in the tow vehicle and cameras surrounding the load plate that allow the operator to get a good view of the pavement surface in the vicinity of the load plate. As the equipment is moved into a testing position, the surface area should be checked to be sure it is clean and free of debris. A clean test location ensures the load plate will seat properly and that reliable deflection data will be recorded.

If the deflection data look suspicious, the operator should rerun the test sequence at the same location. Typical deflection anomalies include nondecreasing deflections from the load plate and high D1 sensor (load plate) deflections compared to previous tests in that test lane. These anomalies may occur because of anomalies in the pavement structure or may indicate an equipment problem. In either case, the NDT operator should repeat the test at least once.

CHAPTER 6. TEST PROCEDURES › 30. Special Test Conditions.

34 CHAPTER 6. TEST PROCEDURES

As testing proceeds along the test lane and pavement facility, differences in the pavement construction may require alteration of the NDT test plan. For example, the width of an HMA paving lane may change and require the planned offset distance from the centerline to be changed to avoid being within 3 ft (1 m) of the longitudinal construction joint. These changes should be annotated on the NDT plan sketch and should include information as to why the changes are needed and at what lane and station location the change was made.

3 0 . Special Test Conditions. For the following scenarios, testing time and locations may have to be changed to safely collect accurate deflection data.

a. High or Low Temperatures. Many NDT devices will not operate properly when the ambient air temperature is too high or too low. If the temperature is too low, many manufacturers do not recommend conducting NDT because of the stress put on the equipment, especially those devices that are hydraulically operated. Likewise, if the temperature is too high, an HMA surface layer may compress excessively, leading to the recording of low-quality data. For these scenarios, the testing should be postponed until more moderate temperatures are encountered.

b. High-Volume Landside Roads. If testing must be conducted during the day, traffic control procedures should be used similar to those typically used by state Department of Transportation. Alternatively, testing should be conducted late at night when traffic levels have decreased to an acceptable level.

c. Sensor Configurations for PCC Testing. As discussed in Chapter 5, the NDT plan may require tests to be performed at the center, corner, transverse joint, and longitudinal joints of PCC slabs. These tests may also have to be performed at these locations for HMA overlaid PCC when cracks have reflected to the surface from underlying joints. The manufacturer’s NDT devices and operation software may permit additional sensors to be installed on both sides and behind the load plate, as shown in Figure 22.

PLATE

PLATE

PLATE

PLATE

TRANSVERSE

JOINT TEST

SLAB CENTER

TEST

SLAB CORNER TEST

LONGITUDINAL JOINT TEST

DIRECTION OF TESTING

Figure 22. Location of Additional Sensors for Corner and Joint Testing

Figure 22: picture of page 40Figure 22 · page 40
Picture of the page from the copy saved here

CHAPTER 6. TEST PROCEDURES › 31. Onsite Review of Data.

CHAPTER 6. TEST PROCEDURES 35

As Figure 22 indicates, no additional sensors are required to collect slab center and transverse joint deflections along the PCC lane. However, an additional sensor behind the load plate will allow for transverse joint load transfer with the load plate on either side of the joint. This may be important if the aircraft or vehicle traffic is largely unidirectional.

On PCC pavement, the NDT operator should conduct corner tests so the load plate is within 6 in (15 cm) of the transverse and longitudinal joints. An additional side sensor allows the operator to efficiently move the NDT equipment forward and test for load transfer across the longitudinal joint. Properly positioned cameras on the NDT device around the load plate make this maneuver much easier.

3 1 . Onsite Review of Data. At the end of each day’s testing, the operator should review the NDT data files to ensure the data have been properly recorded. This is also a good time to add any additional comments to the file while the testing events are still fresh in the operator’s mind. The operator should review all files prior to leaving the job site. If there are significant errors or anomalies in the test data, additional tests should be conducted before leaving the site. This eliminates the need to remobilize should these errors not be discovered until after the NDT equipment has left the site.

Although Chapter 7 discusses NDT data analysis, it is important to mention that an onsite preliminary analysis of the deflection data may be extremely valuable. A plot of raw deflection data and ISM values versus station for each pavement facility may show suspect areas where additional test points would improve the reliability of the analysis results.

36 CHAPTER 6. TEST PROCEDURES

Intentionally Left Blank

CHAPTER 7. DEFLECTION DATA ANALYSES › 33. Overview of Process.

CHAPTER 7. DEFLECTION DATA ANALYSES 37

CHAPTER 7. DEFLECTION DATA ANALYSES

3 2 . General. This chapter presents the next step in the pavement study -- analyzing the deflection data to obtain pavement structural characteristics that are needed to complete the project-level or networklevel study. This chapter introduces several analysis procedures that can be used to obtain the desired pavement characteristics for an HMA, PCC, or HMA overlaid PCC pavement.

3 3 . Overview of Process. Figure 23 provides an overview of the NDT data analysis process. Chapter 7 focuses on the analysis of the deflection data to evaluate the characteristics of the existing pavement structure. Chapter 8 then focuses on how engineers use these pavement characteristics in structural capacity analyses, rehabilitation designs, and the development of a multiyear CIP for a pavement management system.

Figure 23. NDT Data Analysis And Design Flowchart

Figure 23: picture of page 43Figure 23 · page 43
Picture of the page from the copy saved here

As shown in Figure 23, there are several characteristics that are used to evaluate the structural condition of an existing pavement structure. The most common use of deflection data is to measure the strength of the structure as a whole and each individual layer within the structure. Because most PCC pavements are built using expansion, contraction, and construction joints, several additional characteristics are used to evaluate the condition of the concrete pavements. These discontinuities in the PCC create opportunities for the joint to deteriorate and transfer less load to the adjacent slab, lead to higher deflections at slab corners that may create voids beneath the slab, and provide opportunities for excessive moisture accumulation at the joints that may accelerate PCC material durability problems.

38 CHAPTER 7. DEFLECTION DATA ANALYSES

a. FAA Software Tools. Table 7 shows the software tools that are available to analyze the deflection data, conduct a structural evaluation, perform a rehabilitation design, or develop a new pavement cross-section. The tools shown in Table 7 will require varying levels of pavement engineering expertise to correctly use them. Before using these tools, it is important to understand their theoretical basis. Most software is accessible from the FAA web site www.faa.gov.

Table 7. FAA Software Tools for Pavement Analysis, Evaluation, And Design

NDT Data Analysis Evaluation 1 Design

Action BAKFAA FEAFAA COMFAA FAARFIELD F806FAA R805FAA

Back-calculate HMA moduli ● Back-calculate PCC moduli ● Back-calculate APC2 moduli ● Compute load transfer ● Conduct void analysis ● Compute allowable loads ● ● ● ● ● Compute remaining life ● ● ● Compute PCN ● Perform HMA overlay design ● ● Perform PCC overlay design ● ●

Design new HMA crosssection ● ● Design PCC Cross-section ● ●

1 These evaluation tools can be used for design checks but are not approved FAA design programs. 2 APC is asphalt overlaid PCC pavements.

b. Background on FAA Software Tools. Most of the design tools shown in Table 7 are based on structural models that use static material property characteristics. Vibratory and impulse NDT devices generate dynamic loads that measure the pavement’s response to those dynamic loads.

Therefore, for selected material properties, adjustments may be required before using the programs in Table 7. These adjustments are discussed throughout this chapter.

Although engineers have several choices regarding FAA software tools, they should select programs that have the same theoretical basis for a study. Stated differently, the back-calculation methods used should be consistent with the forward computational procedure that will be used for structural evaluation and design. As shown in Table 8, the FAA software is based on CBR, elastic layer, or the Winkler foundations. Since there are no NDT data analysis tools that are based on CBR, the engineer must use elastic layer theory or the Winkler foundation to perform a NDT data analysis. If the engineer wants to use elastic layer theory for the study, elastic layer-based programs should be used for NDT data analysis, pavement evaluation, and pavement design. The same would be true for studies based on the Winkler foundation. For CBR-based studies, the engineer should use an elastic layer program, such as BAKFAA, for NDT data analysis and then convert the elastic modulus values to CBR values, as discussed in Chapter 8.

The design theory and, hence, the software tool that should be used to analyze pavement performance is based primarily on pavement type. HMA or flexible pavements are analyzed and designed using CBR or elastic layer theory. PCC or rigid pavements are routinely evaluated using the Winkler foundation and Westergaard’s theory, layered elastic theory, or a finite element analysis. Composite pavements or HMA

CHAPTER 7. DEFLECTION DATA ANALYSES › 34. Process Raw Deflection Data.

CHAPTER 7. DEFLECTION DATA ANALYSES 39

overlaid PCC are normally analyzed using the Winkler foundation if the HMA overlay is thin. However, if the HMA overlay is very thick relative to the thickness of the PCC, elastic layer analysis may be more appropriate.

Table 8. Theoretical Basis of FAA Software Tools

FAA Tool

Structural Theory

CBR Elastic Layer

Winkler Foundation

Westergaard Finite Element

BAKFAA ●

FEAFAA ●

COMFAA ● ●

FAARFIELD ●

F806FAA ●

R805FAA ●

These programs can be downloaded from the FAA’s website at www.faa.gov.

3 4 . Process Raw Deflection Data. The boundary limits of pavement sections within a facility may have already been defined in a pavement management system or through a review of the construction history. In a pavement management system, a section is defined as an area of pavement that is expected to perform uniformly because of aircraft traffic levels, pavement age, or pavement cross-section. Deflection data can be used to define or refine the limits of all sections within a pavement facility.

If the deflection data have been collected as described in Chapter 6, the data for a pavement facility may be contained in one electronic file. This file may contain several types of deflection data, such as PCC center, slab joint, and slab corner tests. The center deflection data should be extracted from the file and reviewed to identify pavement section limits within the facility.

A preliminary analysis of the center deflection data is routinely conducted by plotting normalized deflections or the ISM along the length of an apron, taxiway, or runway. The ISM or DSM is computed as shown in Chapter 2. Raw data deflections are normalized by adjusting deflections to a standard load. For example, one may want to normalize the deflections to a critical aircraft wheel load of 40,000 lb (18,000 kg), although deflections were recorded at impulse load levels of 31,500 lb (140 kN), 36,000 lb (160 kN), and 42,500 lb (190 kN). Each deflection recorded at these load levels would have to be adjusted as follows to obtain three normalized deflections at a load level of 40,000 lb (180 kN):

Where:

d0n = Normalized deflection Lnorm = Normalized load Lapplied = Applied load d0 = Measured deflection at selected sensor location

When reviewing the profile plots of normalized deflections or ISM values, the engineer should look for patterns of variability. The normalized deflections under the load plate and ISM values provide an

40 CHAPTER 7. DEFLECTION DATA ANALYSES

indication of the overall strength of the entire pavement structure (i.e., pavement layers and subgrade) at each NDT test location. For a given impulse load (for example, 40,000 lb (180 kN)), increasing ISM values or decreasing normalized deflections indicate increasing pavement strength. Example profile plots of ISM and normalized deflects are as illustrated in Figure 24 and Figure 25, respectively.

Figure 24. ISM Plot to Identify Pavement Section Breaks

CHAPTER 7. DEFLECTION DATA ANALYSES 41

Figure 25. Normalized Deflection Plot Used to Identify Pavement Section Breaks

Figure 25: picture of page 47Figure 25 · page 47
Picture of the page from the copy saved here

Figure 24 illustrates how the ISM profile plots were used to identify four different pavement sections within this pavement facility. It is clear from this figure that section 1 is the strongest of all four sections since its average ISM value is significantly higher than all other sections. Although the mean ISM values for sections 2, 3, and 4 are similar, ISM variability is much higher in section 3.

Likewise, section 2 may be the weakest of the sections because the HMA layer is less than 5 in (13 cm) thick or the stabilized base may be very weak. Profile plots can identify locations for coring and boring work that will provide additional information on layer thickness and strength.

Figure 25 shows that normalized deflection profile plots can also be used to identify the limits of pavement sections within a particular facility. As these profile plots show, stronger pavement sections have lower normalized deflections. The engineer can use either normalized deflections or ISM values to identify section limits. ISM values are used more frequently and provide information independent of force.

Deflection data can also be used to identify variations in the subgrade strength along a pavement facility. A sensor that is located a precomputed distance from the center of the load plate may provide a good estimate of the subgrade strength. The American Association of State Highway and Transportation Officials (AASHTO) 1993 design procedures provide guidance for the distance the sensor should be from the load plate to reflect the subgrade strength (for example, outside of the stress bulb at the subgradepavement interface).

For typical modulus values of HMA and PCC and three subgrade strengths Table 9 shows the approximate distance the sensor should be from a 12 in (30 cm) diameter load plate to reflect the subgrade strength. Using Table 9 as a guide, the engineer should select the sensor that is closest to the value shown in the table, which is not necessarily the outermost sensor on the NDT device. Since most NDT devices do not record deflections beyond 72 in (180 cm), this table shows that the outermost sensor may not provide a good indication of the subgrade strength for thick PCC pavements.

42 CHAPTER 7. DEFLECTION DATA ANALYSES

Figure 26 shows that deflections measured 24 in (60 cm) from the center of the load plate can be used to compare subgrade strengths along the pavement facility. Table 9 shows that for all four sections, the NDT sensor at a distance of 24 in (60 cm) from the load plate, is acceptable and should provide a good indication of subgrade strength. Figure 26 shows that subgrade strengths for all four sections are significantly different.

Figure 26: picture of page 48Figure 26 · page 48
Picture of the page from the copy saved here

Table 9. Required Sensor Distance (Inch) From Load Plate with 12 Inch (30 cm) Diameter

Surface Type Surface Layer Thickness, in (cm)

Subgrade CBR

4 (Weak) 12 (Average) 20 (Strong)

HMA

4 (10) 15 12 9

8 (20) 30 24 18

PCC

12 (30) 84 60 48

20(50) 144 108 84

The shaded areas show the required sensor distance beyond the typical NDT equipment maximum of 70 in (180 cm).

Figure 26. Normalized Subgrade Deflection Plot Used to Identify Pavement Sections

Once the boundary limits of the pavement sections have been refined or defined within a pavement facility, the raw deflection data for each section must be separated from the facility data file for analysis.

CHAPTER 7. DEFLECTION DATA ANALYSES › 35. Back-Calculation Analysis.

CHAPTER 7. DEFLECTION DATA ANALYSES 43

After the deflection test data has been separated by pavement section, the data need to be further subdivided by NDT test type. As shown in Figure 23, the following types of deflection data collection will be required to conduct the analysis work described in this chapter:

a. Center Deflection (Deflection Basin) Data. Pavement layer strengths and material durability.

b. Joint and Crack Deflection Data. Joint condition and material durability.

c. PCC Slab Corner Deflection Data. Support conditions and material durability.

3 5 . Back-Calculation Analysis. The engineer can use deflection basin data from flexible pavements and rigid center NDT tests to compute the strength of pavement layers. The process that is used to conduct this analysis is referred to as back-calculation because the engineer normally does the opposite of traditional pavement design. Rather than determining the thickness of each pavement layer based on assumed layer strengths, back-calculation typically involves solving for pavement layer strengths based on assumed uniform layer thicknesses. Throughout the remainder of this chapter, layer strength is referred to in terms of Young’s modulus of elasticity or simply the elastic modulus.

As discussed in this AC, the types of loads that are applied through the use of NDT equipment fall into two general categories: static loads and dynamic loads. Dynamic loads include vibratory and impulse load NDT devices discussed in Chapter 3. For both static and dynamic loads, the pavement can respond linearly or nonlinearly to the applied loads.

Table 10 shows the possible scenarios that may exist during back-calculation work. In addition, this table shows that finite element-based tools are required for theoretical modeling of pavements that are dynamically loaded by vibratory- and impulse-based NDT devices. However, for routine fieldwork, the FAA supports those software tools that are commonly used by all agencies and consultants who work in the pavement industry. This includes those tools in Table 10 that fall in the static-linear category.

Table 10. Area-Based Constants for Equation 8

Area Method

Constant

A B C D

SHRP 4-sensor (0 to 36 in (0 to 90 cm) 36 1812.279 -2.559 4.387

SHRP 7-sensor (0 to 60 in (0 to 150 cm) 60 289.078 -0.698 2.566

SHRP 5 outer sensors (12 to 60 in (30 to 150 cm) 48 158.408 -0.476 2.22

Air Force 6 outer sensors (12 to 72 in (30 to 180 cm) 60 301.8 -0.622 2.501

Back-calculation analysis work that falls in the static-linear category is typically conducted using two procedures. The first category allows the engineer to use closed-form procedures that directly compute the elastic modulus of each layer by using layer thicknesses and deflections from one or more sensors. The second category uses an iterative mechanistic process to solve for the elastic modulus by using layer thicknesses and deflections from at least four sensors.

Before conducting an analysis, the engineer should review the deflection tests that have been separated by pavement facility and section for back-calculation. Regardless of the software tool that will be used in the analysis, linear-elastic theory requires that pavement deflections decrease as the distance from the NDT

44 CHAPTER 7. DEFLECTION DATA ANALYSES

load plate increases. In addition, for typical NDT sensor configurations, the deflections should gradually decrease from the load plate to the outermost sensor.

Deflection basin anomalies could occur for several reasons, including the presence of a crack near the load plate, a nonfunctioning sensor, sensor and NDT equipment configuration error, sensors not properly calibrated, voids, loss of support, temperature curling or moisture warping of PCC slab, or several other reasons. The engineer should review the deflection data and remove those data that have the following anomalies.

 Type I Deflection Basin. In this scenario, the deflections at one or more of the outer sensors are greater than the deflection under the load plate. This type of anomaly will produce the largest error during back-calculation analysis.  Type II Deflection Basin. Another less obvious anomaly is an unusually large decrease in deflection between two adjacent sensors. While elastic layer theory requires deflections to decrease as the distance from the load plate increases, the amount of decrease should be gradual and relatively consistent between all sensors.  Type III Deflection Basin. Similar to Type I, the deflection at the outermost sensor of two adjacent sensors is greater than the deflection at the sensor that is closest to the load plate.

Figure 27 summarizes the deflection data preparation and analysis tool selection processes. The AASHTO closed-form procedure for flexible pavements is appropriate for landside pavements and airside access roads where truck and other vehicle traffic are the predominant types of loading, and the analysis will be based on the AASHTO Design Guide. For PCC pavement analysis, HMA overlays are considered to be thin if they are less than 4 in (10 cm) thick and the PCC layer thickness is less than 10 in (25 cm). The HMA overlay is also considered to be thin if it is less than 6 in (15 cm) thick and the PCC layer is greater than 10 in (25 cm) thick.

Figure 27. Process for Data Preparation and Back-Calculation Method Selection

Figure 27: picture of page 50Figure 27 · page 50
Picture of the page from the copy saved here

a. Closed-Form Back-Calculation. Closed-form back-calculation algorithms are commonly used when the results will be used for two specific design methodologies. The first methodology is based on the 1993 AASHTO Design Guide for HMA pavements that relies on the resilient modulus (M,) of the subgrade as computed by laboratory testing. The second algorithm, commonly referred to as the AREAbased methodology, is used primarily for PCC or HMA overlaid PCC pavements when the design procedure relies on the modulus of subgrade reaction, k, as discussed in Chapter 8.

CHAPTER 7. DEFLECTION DATA ANALYSES 45

Equation 2 shows that the M, value for the subgrade can be calculated by using the deflections from the appropriate sensor of the NDT equipment. Referring to Figure 26, this would be the 24 in (60 cm) from the center of the load plate based on guidelines presented in Table 9.

Where:

Mr = Resilient modulus, in psi P = Applied load, in pounds dr = Measured deflection at distance r from applied load, in inches r = Radial distance at which the deflection is measured, in inches

Table 11. Type of Back-Calculation Software Tool Required for Each Load Scenario

Material Response

Type of Load Application

Static Dynamic

Linear Closed-form and iteration-based tools Finite Element Tools

Non-Linear Iteration Based Tools Finite Element Tools

Dynamic loads include those generated by vibratory and impulse load NDT equipment.

For the four pavement sections shown in Figure 26, the dynamic resilient modulus values for the subgrade would be as follows if the mean 12 in (60 cm) sensor deflections were used in the above equation: section 1, 72,150 psi (497 MPa); section 2, 26,780 psi (185 MPa); section 3, 43,650 psi (301 MPa); and section 4, 33,170 psi (229 MPa). The four mean deflections for this sensor position are 2.76, 7.48, 4.57, and 6.02 mils.

As expected, the subgrade strength for section 1 is the highest because it has been stabilized. These subgrade modulus values would have to be adjusted to laboratory resilient modulus values using a correction factor (typically, 0.33), as discussed in the 1993 AASHTO Design Guide, before conducting an HMA pavement design or evaluation in accordance with those design procedures.

Another commonly used closed-form back-calculation procedure is the AREA-based methodology. This methodology, also used in the 1993 AASHTO Design Guide, is predominantly used for PCC and HMA overlaid PCC pavements when the design tool uses the subgrade modulus, k. AREA is computed by using NDT deflections that form the deflection basins described in Chapter 2.

Continue reading ↓ 120 of 195 passages shown