Radar Vectors
FAA Order Cancelled Issued Oct 1, 2005 AJW-331 570 pages Copy saved Nov 18, 2026

Order 8200.1C United States Standard Flight Inspection Manual (with Changes 1, 2, 3, 4, 5, 6, 7, 8, and 9 Incorporated)

This document is cancelled. Cancelled by 8200.1D. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (1 of 570 pages). Check the original, as some words may be misread.

Cover

DEPARTMENT OF THE ARMY TECHNICAL MANUAL TM 95-225

DEPARTMENT OF THE NAVY MANUAL NAVAIR 16-1-520

DEPARTMENT OF THE AIR FORCE MANUAL AFMAN 11-225

FEDERAL AVIATION ADMINISTRATION ORDER 8200.1C

UNITED STATES

STANDARD FLIGHT INSPECTION

MANUAL

October 2005

DEPARTMENTS OF THE ARMY, THE NAVY, AND THE AIR FORCE

AND THE FEDERAL AVIATION ADMINISTRATION

DISTRIBUTION: ZVN-820 Initiated By: AJW-331

DIRECTIVE NO. RECORD OF CHANGES 8200.1C

CHANGE SUPPLEMENTS OPTIONAL CHANGE SUPPLEMENTS OPTIONAL TO BASIC

TO BASIC

1

2

3

4

5

The material contained herein was formerly issued as the United States Standard Flight Inspection Manual, dated December 1956.

The second edition incorporated the technical material contained in the United States Standard Flight Inspection Manual and revisions thereto and was issued as the United States Standard Facilities Flight Check Manual, dated December 1960.

The third edition superseded the second edition of the United States Standard Facilities Flight Check Manual; Department of Army Technical Manual TM-11-2557-25; Department of Navy Manual NAVWEP 16-1-520; Department of the Air Force Manual AFM 55-6; United States Coast Guard Manual CG-317.

FAA Order 8200.1A was a revision of the third edition of the United States Standard Flight Inspection Manual, FAA OA P 8200.1; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; Department of the Air Force Manual AFMAN 11-225; United States Coast Guard Manual CG-317.

FAA Order 8200.1B, dated January 2, 2003, was a revision of FAA Order 8200.1A. The current FAA Order 8200.1C is effective October 15, 2005.

6

7

8

9

Chg 9 Cover › Chg 9 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 9 to

8200.1C

11/02/2014

SUBJ: United States Standard Flight Inspection Manual 1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005. 2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Aviation System Standards; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees. 3. Where Can I Find This Change? Go to http://www.faa.gov/regulations_policies/orders_notices/#browseTopics. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/). 4. Explanation of Policy Changes. Changes periodic flight inspection interval for Instrument Landing System (ILS) and Localizer Directional Aid (LDA)/Simplified Directional Facility (SDF) with Glideslope (GS) facilities. This change was endorsed by a Safety Risk Management Panel on August 5, 2014. Panel members included Flight Standards, NAS Engineering, the National Resource Engineer for Navigation, Flight Inspection Services, Safety Services, Safety Engineering, and Safety Management Oversight.

a. Chapter 4, Paragraph 4.25. Requires monitor inspection every periodic for ILS and LDA/SDF with GS. Periodic inspection requirements for LDA/SDF/Localizer (LOC) only facilities do not change.

b. Table 4-1. Changes ILS and LDA/SDF with GS periodic interval from 270 to 540 days.

PAGE CONTROL CHART

REMOVE

PAGES

DATED INSERT

PAGES

DATED

Page 4-9 05/30/2011 Page 4-9 11/02/2014 Page 4-10* 10/01/2005 Page 4-10* 10/01/2005 *Page did not change Robert P. Walker Acting Director Flight Inspection Services

Page 2

Chg 8 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 8 to

8200.1C

09/29/2013

SUBJ: United States Standard Flight Inspection Manual 1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005. 2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Aviation System Standards; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees. 3. Where Can I Find This Change? Go to http://www.faa.gov/regulations_policies/orders_notices/#browseTopics. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/). 4. Explanation of Policy Changes.

a. General: Incorporates the concept of “flight validation” in Chapters 6 and 13. Flight validation is a flight assessment of an instrument flight procedure concerned with factors other than the performance of a navigation aid or system. Evaluation of ARINC 424 coding is a prime focus of the validation process. Multiple paragraphs in Chapter 6 were moved and renumbered. A new section 6.11, “The Validation Process” was added, and all subsequent sections renumbered. The list below uses paragraph references as they appear in the new change.

b. Chapter 6, Paragraph 6.10 and 6.11. Defines the Validation Process, including the Preflight and Flight Validation of Instrument Flight Procedures. This brings Flight Inspection guidance up to date with current Flight Standards and ICAO practices.

c. Chapter 6, Paragraph 6.12a, b. Expanded and reorganized guidance on reviewing a procedure package.

d. Chapter 6, Paragraph 6.12c. Added details for conducting evaluations of RNAV IFPs using a flight simulator.

e. Chapter 6, Paragraph 6.12e. Changed guidance for verifying obstacle heights in flight to improve the accuracy code. It is no longer a routine action, and should only be done when all other avenues have been exhausted.

f. Chapter 6, Paragraph 6.13b (Checklist). Added Checklist item, “Runway Markings, Lighting, and Supporting Infrastructure.” This was always required if you read the text, but not included in the checklist explicitly. Also moved the “Obstacle Verification” to the top to mirror the new organization in the chapter.

g. Chapter 6, Paragraph 6.13b (Checklist). Reworded Note 2 to improve clarity. Added Note 3 to emphasize conducting a surveillance check of associated VGSIs when possible. This is in keeping with the safety mitigations when VGSI periodics were eliminated.

h. Chapter 6, Paragraph 6.13c(1)(e). Removes the requirement to conduct an airborne obstacle verification when the entire procedure segment is above a previously established minimum IFR altitude.

i. Chapter 6, Paragraph 6.13c(2). Added guidance for obstacle evaluations of new or amended approach procedures.

j. Chapter 6, Paragraph 6.13c(3). Added guidance for obstacle evaluation during periodic inspections.

k. Chapter 6, Paragraph 6.13c(9)(c). Updated guidance for estimating the height of newly discovered obstacles. Do not attempt to measure obstacle heights in flight when other means are practical. If it is measured in flight, the preferred method is to use GNSS avionics to determine the altitude.

l. Chapter 6, Paragraph 6.13c(13). Added instructions for checking Advisory Vertical Guidance on non-precision approaches.

m. Chapter 6, Paragraph 6.13d. Expanded guidance for Airways, Routes, and Terminal Route Segments.

n. Chapter 6, Paragraph 6.13g. Allows for some segments of RNAV SIAP(s) based on GNSS to not be flown per the instructions found in Chapter 13.

o. Chapter 6, Paragraph 6.13g(3)(b). Flying to 100 feet below the MDA does not apply to GNSS-only RNAV SIAPs.

p. Chapter 6, Paragraph 6.13h. Expanded information on assessing flyability per AFS and ICAO guidance.

q. Chapter 6, Paragraph 6.13i. Moved and expanded paragraph on Departure Procedures. Updated terminology for departure procedures and graphical and textual obstacle departure procedures. Additional guidance for “low, close-in obstacles.”

r. Chapter 6, Paragraph 6.14b(3)(a). Added statement that “minor changes [to approach lighting] may not require a night evaluation.”

s. Chapter 6, Paragraph 6.14c. Changed assessment standard for human factors from, “a minimally qualified sole pilot flying an aircraft with basic IFR instrumentation…” to “the target user with the minimum required IFR instrumentation.” The intent is to allow for procedures designed for specific aircraft capabilities, and/or specific crew training. The wording still allows for the target user to be that minimally qualified sole pilot with basic instrumentation when applicable.

t. Chapter 6, Paragraph 6.15. Expanded language in general tolerance guidance to include factors associated with data-based RNAV instrument flight procedures.

Page 2

u. Chapter 13, Paragraph 13.11.c. Pilot Defined Procedure requires FIS Technical Services guidance.

v. Chapter 13, Paragraph 13.11.d. Expands guidance for use of desk-top evaluation of ARINC 424 coding. With an in-depth ARINC 424 evaluation, with an approved desktop software and documentation, some procedural segments may not have to be flown.

w. Chapter 13, Paragraph 13.12.a. Checklist note (4) added requiring two miles of the intermediate segment to be flown for proper avionics approach activation.

x. Chapter 13, Paragraph 13.12.c.(1) “Low, close-in” obstacles addressed on departure procedures.

y. Chapter 13, Paragraph 13.12.c.(2) Updated radar coverage requirements.

z. Chapter 13, Paragraph 13.12.c.(3) Corrected wording on positioning aircraft for STAR vertical flyability from “steepest” to “shallowest descent path”.

aa. Chapter 13, Paragraph 13.12.c.(4) Deleted requirement to fly 100’ below MDA. This was a holdover from ground based navaids to check coverage. GPS coverage is from the surface of the earth and above. Added requirement to evaluate ARINC 424 coding providing VDA below MDA per guidance in Chapter 6.

bb. Chapter 13, Paragraph 13.31. The change allows that previously verified DME/DME coverage along the same routing and altitudes may be used in lieu of a new flight inspection. The change also recognizes that a valid DME/DME coverage prediction-modeling tool may be used in lieu of flight inspection for coverage verification on procedure and route segments at and above 18,000 feet.

cc. Chapter 13, Paragraph 13.42.c. Added guidance for offset LPV and LP procedures.

dd. Appendix 1. Added definitions for preflight validation and deletes geostationary earth orbit satellite.

PAGE CONTROL CHART

REMOVE

PAGES

DATED INSERT

PAGES

DATED

Pages 6-i thru 6-9(and 10) Various Pages 6-i thru 6-22 09/29/2013 Pages 13-1 thru 13-18 Various Pages 13-1 thru 13-20 09/29/2013 Pages A1-1 thru 1-44 05/30/11 Pages A1-1 thru 46 09/29/2013 *Page did not change Edward W. Lucke, Jr. Director Flight Inspection Services

This Page Intentionally Left Blank.

Chg 7 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 7 to

8200.1C

03/17/2013

SUBJ: United States Standard Flight Inspection Manual

1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005.

2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Aviation System Standards; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees.

3. Where Can I Find This Change? Go to http://www.faa.gov/regulations_policies/orders_notices/#browseTopics. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

4. Explanation of Policy Changes.

a. Chapter 11, Removed all instances of “course sensitivity” because the check is no longer described in the chapter. Tolerance and method to check course sensitivity was removed in change 1 to 8200.1A.

b. Chapter 11, Paragraph 11.12. Removed last sentence; it contradicted the requirements in the VOT section.

c. Chapter 11, 11.12 Checklist. Added note 14 to emphasize when TACAN null checks should be performed.

d. Chapter 11, Paragraph 11.20.a. Removed the instructions to re-establish the reference radial and alignment orbit when during a periodic inspection Alignment Reference Radial (ARR) alignment is found to have shifted more than 1°. A new radial selection may be no better than the one replaced. It may also show an alignment shift the orbit will not confirm. Technical Operations Services Maintenance is not concerned with the ARR alignment as they use the orbital alignment as their reference for ground checks. The intent is to give maintenance a chance to evaluate the facility before any changes are made. If the ARR alignment shifts by more than 1° from previously established, perform an alignment orbit and then follow the requirements of paragraph 11.20f(1)(f) in the 8200.1C.

e. Chapter 11, Paragraph 11.20.e.(5)(a)1. Improved description of cases when a TACAN null check is required.

f. Chapter 11, Paragraph 11.20.f.(1)(b). Corrected due to a name changed.

g. Chapter 11, Paragraph 11.20.f.(2)(a). Changed the paragraph to add obstructions as a consideration during the preflight map study. Current coverage orbit required altitudes are 1000 ft (2000 ft in designated mountainous areas) above antenna elevation and intervening terrain. The change improves safety by keeping the aircraft above obstacles that may be in its path, and is consistent with earlier practices.

h. Chapter 11, Paragraph 11.33. Added coverage requirements for a stand-alone DME facility.

PAGE CONTROL CHART

REMOVE

PAGES

DATED INSERT

PAGES

DATED

Page 11-1* 02/01/07 Page 11-1 02/01/07 Page 11-2 02/01/07 Page 11-2 03/17/13 Page 11-3 02/01/07 Page 11-3 03/17/13 Page 11-4* 02/01/07 Page 11-4 02/01/07 Page 11-5* 09/14/09 Page 11-5 09/14/09 Page 11-6 02/01/07 Page 11-6 03/17/13 Page 11-7* 02/01/07 Page 11-7 02/01/07 Page 11-8 11/05/07 Page 11-8 03/17/13 Page 11-27 02/01/07 Page 11-27 03/17/13 Page 11-28* 02/01/07 Page 11-28 02/01/07 *Page did not change Edward W. Lucke, Jr. Director Flight Inspection Services

Chg 6 Cover

Edward W. Lucke, Jr. Director Flight Inspection Services

CHANGE U.S. DEPARTMENT OF TRANSPORTATION Change 6 to FEDERAL AVIATION ADMINISTRATION 8200.1C

03/25/12

SUBJ: United States Standard Flight Inspection Manual

1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005.

2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Flight Inspection Services; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees.

3. Where Can I Find This Change? Go to http://www.faa.gov/regulations_policies/orders_notices/#browseTopics. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

4. Explanation of Policy Changes. Chapter 17, Paragraph 17.12g. This Change corrects the Tolerance Table on page 17-18. The Lateral Alignment tolerance is 0.10, but was incorrectly changed to 0.010 in Change 4.

PAGE CONTROL CHART

REMOVE PAGES DATED INSERT PAGES DATED

17-17 05/30/11 17-17 05/30/11 17-18 05/30/11 17-18 03/25/12

This Page Intentionally Left Blank.

Chg 5 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION Change 5 to FEDERAL AVIATION ADMINISTRATION 8200.1C

12/25/11

SUBJ: United States Standard Flight Inspection Manual

1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005.

2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Aviation System Standards; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees.

3. Where Can I Find This Change? Go to http://www.faa.gov/regulations_policies/orders_notices/#browseTopics. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

4. Explanation of Policy Changes. Chapter 11, Paragraph 11.60a. Added Doppler VOR deviation tolerance when measured above 5° angle from the facility to align tolerances with ICAO.

PAGE CONTROL CHART

REMOVE PAGES DATED INSERT PAGES DATED

11-25 02/01/07 11-25 02/01/07 11-26 02/01/07 11-26 12/25/11

This Page Intentionally Left Blank.

Chg 4 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 4 to

8200.1C

5/30/11

SUBJ: United States Standard Flight Inspection Manual

1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005.

2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Aviation System Standards; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees.

3. Where Can I Find This Change? Go to http://www.faa.gov/air_traffic/flight_info/avn/flightinspection/onlineinformation/8200/. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

4. Cancellations:

a. Notice 8200.116, Flight Inspection/ Validation of Ground-Based Augmentation System (GBAS) Precision Approach and Flight Procedures, dated October 30, 2009.

b. Notice 8200.118, Flight Inspection of Wide Area Augmentation System (WAAS) RNAV Instrument Flight Procedures (Order 8200.1C, Chapter 13), dated August 16, 2010.

c. Notices 8200.119, Distance Measuring Equipment (DME) DME/ DME Support Area Navigation (RNAV) (Order 8200.1C, Chapter 13), dated August 16, 2010.

Distribution: Special Addressees Initiated By: Aviation System Standards

Flight Inspection Operations Flight Inspection Policy (AJW-331)

5. Explanation of Policy Changes:

a. Chapter 4. Added GBAS requirements to Paragraphs 4.24 and 4.25 (Table 4-1).

b. Chapter 5. Added GBAS requirements to Paragraphs 5.12d and 5.12i(8).

c. Chapter 13. Updated “AFIS” to “FIS”, deleted instructions for AFIS, updated terminology, and updated FAA Order numbers and titles throughout the chapter.

Language).

(1) Paragraph 13.10. RNAV sensor systems listed in bullet format (Plain

(2) Paragraph 13.11b. Added ARINC 424 requirements.

(3) Paragraphs 13.12 and 13.13. Included term “navigation data” in evaluation of RNAV procedures. Clarified requirements for periodic inspection of RNAV.

(4) Paragraph 13.21. Clarified obstacle evaluation requirements.

(5) Paragraph 13.32. Clarified GNSS navigation.

(6) Paragraph 13.33. Analysis guidance rewritten to delete obsolete information.

(7) Paragraph 13.34. Deleted Parameter/ Tolerance PEE/ < RNP Limit and TSE/ < RNP Limit.

(8) Paragraph 13.41. Deleted Paragraph 13.41a, “Pilot-Defined Procedure”. Added threshold crossing height to items FIS uses the FAS data to calculate.

(9) Paragraph 13.44, Tables 13-2 and 13-3. Deleted Parameter/ Tolerance SNR-W/ ≥ 30 dB/Hz.

d. Chapter 14:

(1) Paragraph 14.25a. In the checklist, replaced “X” in the “AZ Alignment” box for “Azimuth Only” with Note “(4)”. Added Note “(4)” to the bottom of the checklist notes, “(4) Measure alignment at threshold.” Clarifies what to measure.

(2) Paragraph 14.25b. In the checklist, added Note “(10)” to the “AZ Alignment” box for “Azimuth Only”. Added Note “(10)” to the bottom of the checklist notes, “(10) Measure alignment at threshold.”

(3) Paragraph 14.25c. In the checklist, added Note “(6)” to the “AZ Alignment” box for “Azimuth Only”. Added Note “(6)” to the bottom of the checklist notes, “(6) Measure alignment at threshold.”

(4) Paragraph 14.25d. In the checklist, replaced “X” in the “AZ Alignment” box for “Azimuth Only” with Note “(6)”. Added Note “(6)” to the bottom of the checklist notes, “(6) Measure alignment at threshold.”

(5) Paragraph 14.25d. In the checklist, deleted “X” in the “GP Alignment” box for Azimuth Only”. Glidepath alignment not measured during this check.

Page 2 Par 5

e. Chapter 15:

(1) Paragraph 15.20b. Updated paragraph by deleting “and relocated” from 1st

sentence of * paragraph, as it does not apply when the facility is moved but retains the same antennas.

(2) Paragraph 15.20k(2)(b). Deleted “Monitor Reference Evaluations” subparagraph and renumbered succeeding subparagraphs. An update in maintenance practices requires a final normal clearance value regardless of the clearances found in the monitor configuration.

e. Chapter 17. Expanded to include and update guidance from N 8200.116.

f. Appendix 1. Acronyms and Definitions from N 8200.116 rolled into Appendix 1. Specific definitions updated in accordance with AIM.

PAGE CONTROL CHART

REMOVE PAGES DATED INSERT PAGES DATED

4-7 10/01/05 4-7 10/01/05 4-8 02/01/07 4-8 5/30/11 4-9 11/01/10 4-9 5/30/11 4-10 10/01/05 4-10 10/01/05 5-1 10/01/05 5-1 10/01/05 5-2 02/01/07 5-2 5/30/11 5-3 02/01/07 5-3 02/01/07 5-4 and 5 11/01/10 5-4 and 5 5/30/11 5-6 02/01/07 5-6 5/30/11 13-i and ii 02/01/07 13-i and ii 5/30/11 13-1 10/01/05 13-1 5/30/11 13-2 02/01/07 13-2 5/30/11 13-3 9/14/09 13-3 5/30/11 13-4 10/01/05 13-4 5/30/11 13-5 thru 10 02/01/07 13-5 thru 10 5/30/11 13-11 thru 17 (and 18) 9/14/09 13-11 thru 18 5/30/11 14-33 11/01/10 14-33 11/01/10 14-34 thru 14-39 11/01/01 14-34 thru 14-39 5/30/11 14-40 11/01/10 14-40 11/01/10 14-45 11/01/10 14-45 5/30/11 14-46 11/01/10 14-46 11/01/10

Par 5 Page 3

PAGE CONTROL CHART

(continued)

REMOVE PAGES DATED INSERT PAGES DATED

15-27 10/01/05 15-27 10/01/05 15-28 02/01/07 15-28 5/30/11 15-43 02/0107 15-43 02/01/07 15-44 and 45 02/01/07 15-44 and 45 5/30/11 15-46 02/01/07 15-46 02/01/07 17-i thru 17-1 (and 2) 11/01/10 17-i thru 17-18 5/30/11 A1-1 thru A1-5 10/01/05 A1-1 thru A1-5 5/30/11 A1-6 and A1-7 02/01/07 A1-6 and A1-7 5/30/11 A1-8 and A1-9 10/01/05 A1-8 and A1-9 5/30/11 A1-10 thru A1-12 02/01/07 A1-10 thru A1-12 5/30/11 A1-13 thru A1-15 10/01/05 A1-13 thru A1-15 5/30/11 A1-16 thru A1-18 9/14/09 A1-16 thru A1-18 5/30/11 A1-19 thru A1-32 10/01/05 A1-19 thru A1-32 5/30/11 A1-33 9/14/09 A1-33 5/30/11 A1-34 thru A1-36 02/01/07 A1-34 thru A1-36 5/30/11 A1-37 thru A1-40 10/01/05 A1-37 thru A1-44 5/30/11 Edward W. Lucke, Jr. Acting Director of Aviation System Standards

Page 4 Par 5

Chg 3 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 3 to

8200.1C

11/01/10

SUBJ: United States Standard Flight Inspection Manual

1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C; Department of the Army Technical Manual TM 95-225; Department of the Navy Manual NAVAIR 16-1-520; and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005.

2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Aviation System Standards; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees.

3. Where Can I Find This Change? Go to http://www.faa.gov/air_traffic/flight_info/avn/flightinspection/onlineinformation/8200/. Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

4. Cancellations:

a. N 8200.115, FAA Order 8200.1C, Chapters 4 and 20, dated July 27, 2009

b. N 8200.117, Wide Area Multilateration (WAM), dated November 16, 2009

c. N 8200.120, Markers/ Beacons Major Axis Tolerance (Order 8200.1C, Chapter 24), dated August 20, 2010.

d. N 8200.121, MLS DME and TACAN Distance Accuracy Tolerances (Order 8200.1C, Chapter 24), dated August 20, 2010.

Distribution: Special Addressees Initiated By: Aviation System Standards

Flight Inspection Operations Flight Inspection Policy (AJW-331)

5. Explanation of Policy Changes:

a. Chapter 4:

(1) Paragraph 4.25, Table 4-1. Added WAM to list of facilities with 540-day periodic interval. VFR Aeronautical Charts deleted.

(2) Paragraph 4.25, Table 4-1, Note (5). Reworded note on periodic SIAP inspections to clarify requirements.

b. Chapter 5, Paragraph 5.12j(11). Reworded NOTAM wording per current guidance.

c. Chapter 7:

run.

(1) Paragraph 7.12b(2)(b)1. Corrected instructions for starting position for a level

(2) Paragraph 7.12b(2)(c)1. Clarified description of Level Run method.

(3) Paragraph 7.12b(2)(c)2. Clarified description of On Path method.

(4) Paragraph 7.12b(2)(c)2a. Added reference to VASI diagrams.

(5) Paragraph 7.12b(3)(a). Added “normally”, as sometimes they are not aligned with the runway.

(6) Paragraph 7.12(4)(a). Added reference to blanking devices and baffles.

(7) Paragraph 7.12b(7)(a)2. Clarified how to determine VGSI coincidence with Baro_VNAV procedures.

(8) Paragraph 7.14c. Added information about blanking devices and baffles.

d. Chapter 14:

(1) Title chapter changed to “Surveillance”.

(2) Table of Contents and Paragraph 14.13. Changed Section 1 Title to include WAM and Paragraph 14.13 title to read, “Surveillance Radar/ ATCRBS Checklist”.

(3) Paragraph 14.10. Added WAM.

(4) Paragraph 14.11c. Removed specific instructions for reporting MSAW discrepancies that are below the level of detail appropriate for this order.

(5) Paragraph 14.11c(1)(a). Removed specific instructions for reporting MSAW discrepancies that are below the level or detail appropriate for this order.

(6) Paragraph 14.12a. Added reference for WAM inspections.

Page 2 Par 5

Checklist.

(7) Paragraph 14.13. Changed title of Checklist to differentiate from WAM

(8) Paragraph 14.14g(2). Facility Maintenance/ Engineering should choose a radial.

(9) Paragraph 14.14t(2). Removed specific instructions for reporting MSAW discrepancies that are below the level of detail appropriate for this order.

(10) Paragraph 14.15 in its entirety. Instructions for WAM inspections added.

(11) Paragraph 14.16 in its entirety. Instructions for WAM inspections added.

(12) Paragraph 14.17 in its entirety. Instructions for WAM inspections added.

(13) Paragraph 14.19, Tolerances. Updated with WAM tolerances per the WAM Notice.

(14) Paragraph 14.23b. Added exception to required equipment for Military Contingency or Natural Disaster.

(15) Paragraph 14.25b, Checklist. Note 4 changed to make Scan-Only an Mx request configuration change.

(16) Paragraph 14.25d. Opening paragraph updated with latest operational information from military, including the addition of TPN-31A PAR.

(17) Paragraph 14.25d, Checklist. “Rain/ Clear” column removed from “Measurements Required” section. This is a configuration, not an item to be checked.

(18) Paragraph 14.25d, Checklist. Note 2 clarified.

(19) Paragraph 14.25d, Checklist. Note 5 added. Added information on AZ-only mode of operation.

(20) Section 3, Automatic Dependent Surveillance Broadcast (ADSB), added as a reserved section to the Table of Contents and the end of Chapter 14.

e. Chapter 15:

(1) Paragraph 15.12h(7). Editorial only. “Angle” removed from “Structure” column of “Phase” in Endfire Glide Slope checklist.

f. Chapter 17. Changed title to Ground-Based Augmentation System (GBAS). The FAA version of GBAS is Local Area Augmentation System (LAAS).

g. Chapter 20. Added to Paragraph 20.10 as last sentence, “VFR charts will be evaluated on an on-demand, as needed basis and have no minimum periodic interval.”

h. Chapter 22. Deleted 3rd sentence. Localizer ESV(s) are not done outside Sector 1.

Par 6 Page 3

i. Chapter 24:

(1) Paragraph 24.21c. Paragraph reworded for clarity.

(2) Paragraph 24.24d. Added advisory information about potential confusion over facility status.

(3) Paragraph 24.40, ILS Glide Slope Checklist. Reworded “Clearance” Procedures for clarity.

(4) Paragraph 24.40. Reworded “Course Structure” Procedure for clarity.

(5) Paragraph 24.41, ILS Localizer Checklist. Reworded “Coverage” Procedures for clarity.

(6) Paragraph 24.41. Reworded “Course Structure” Procedures for clarity.

(7) Paragraph 24.42, Markers/ Beacons Checklist. Changed Major Axis Tolerance. Major Axis measurement is not essential to establishing safe operations.

(8) Paragraph 24.43, Microwave Landing System Checklist. Reworded “Vertical Coverage” Procedures for clarity.

(9) Paragraph 24.43. Reworded “Control Motion Noise” Procedures for clarity.

(10) Paragraph 24.43. Changed DME tolerance.

(11) Paragraph 24.44, VOR Checklist. Reworded first note for clarity.

(12) Paragraph 24.45, TACAN Checklist. Changed Distance Accuracy Tolerances/ Procedures wording. Reworded first note for clarity.

6. Disposal of Transmittal. After filing the revised pages, the change transmittal should be retained.

PAGE CONTROL CHART

REMOVE PAGES DATED INSERT PAGES DATED

4-3 10/01/05 4-3 11/01/10 4-4 02/01/07 4-4 02/01/07 4-9 9/14/09 4-9 11/01/10 4-10 10/01/05 4-10 10/01/05 5-3 02/01/07 5-3 02/01/07 5-4 10/01/05 5-4 11/01/10 5-5 10/01/05 5-5 11/01/10 5-6 02/01/07 5-6 02/01/07

Page 4 Par 6

PAGE CONTROL CHART

(continued)

REMOVE PAGES DATED INSERT PAGES DATED

7-i 10/01/05 7-i 11/01/10 7-ii 10/01/05 7-ii 10/01/05 7-5 9/14/09 7-5 9/14/09 7-6 and 7 02/01/07 7-6 and 7 11/01/10 7-8 10/01/05 7-8 11/01/10 7-9 10/01/05 7-9 10/01/05 7-10 10/01/05 7-10 11/01/10 7-11 10/01/05 7-11 11/01/10 7-12 10/01/05 7-12 10/01/05 14-i 10/01/05 14-i 11/01/10 14-ii 10/01/05 14-ii 11/01/10 14-iii 02/01/07 14-iii 11/01/10 14-iv 14-iv 11/01/10 14-1 and 2 9/14/09 14-1 and 2 11/01/10 14-3 and 4 10/01/05 14-3 and 4 11/01/10 14-5 9/14/09 14-5 11/01/10 14-6 02/01/07 14-6 11/01/10 14-7 9/14/09 14-7 11/01/10 14-8 10/01/05 14-8 11/01/10 14-9 02/01/07 14-9 11/01/10 14-10 thru 18 10/01/05 14-10 thru 18 11/01/10 14-19 02/01/07 14-19 11/01/10 14-20 9/14/09 14-20 11/01/10 14-21 10/01/05 14-21 11/01/10 14-22 9/14/09 14-22 11/01/10 14-23 and 24 10/01/05 14-23 and 24 11/01/10 14-25 02/01/05 14-25 11/01/10 14-26 thru 28 9/14/09 14-26 thru 28 11/01/10 14-29 and 30 02/01/07 14-29 and 30 11/01/10 14-31 9/14/09 14-31 11/01/10 14-32 thru 38 02/01/07 14-32 thru 46 11/01/10 15-23 10/01/05 15-23 10/01/05 15-24 02/01/07 15-24 11/01/10

Par 6 Page 5

This Page Intentionally Left Blank.

Chg 2 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 2 to

8200.1C

9/14/09

SUBJ: United States Standard Flight Inspection Manual

1. Purpose of This Change. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C Department of the Army Technical Manual TM 95-225, Department of the Navy Manual NAVAIR 16-1-520, and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005.

2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Flight Inspection Operations Offices and crewmembers in Aviation System Standards; Flight Standards Flight Technologies and Procedures Division; NAS Implementation Centers; and special military addressees.

3. Where Can I Find This Change? Go to http://www.avn.faa.gov). Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

4. Cancellations. The following Notices are canceled:

a. N 8200.102, Pen and Ink Changes to FAA Order 8200.1C, Change 1, Chapters 4 and 7, dated July 10, 2007.

b. N 8200.103, FAA Order 8200.1C, United States Standard Flight Inspection Manual, Chapter 11, dated July 30, 2007.

c. N 8200.106, Changes to Precision Approach Radar Flight Inspection Requirements, FAA Order 8200.1C, Chapter 14, dated October 15, 2007.

d. N 8200.107, FAA Order 8200.1C, United States Standard Flight Inspection Manual, Chapter 15, dated November 5, 2007.

e. N 8200.108, Pen and Ink Changes to Chapters 4 and 13 of FAA Order 8200.1C, United States Standard Flight Inspection Manual, dated July 25, 2008.

f. N 8200.109, Pen and Ink Changes to Chapter 15 of FAA Order 8200.1C, United States Standard Flight Inspection Manual, Level Run Altitude Adjustment for Weather, dated July 25, 2008.

Distribution: Special Addressees Initiated By: Air Traffic Operations (ATO-W)

Aviation System Standards Flight Inspection Operations Flight Inspection Policy (AJW-331)

g. N 8200.112, FAA Order 8200.1C, Chapter 13 (Area Navigation), dated March 27, 2009.

h. N 8200.113, Elimination of Periodic Inspection of Approach Path Monitors (FAA Order 8200.1C, Chapters 4 and 14), dated April 13, 2009.

i. N 8200.114, RNAV WAAS Glidepath Fly-Up Verification (FAA Order 8200.1C, Chapter 13), dated April 20, 2009.

5. Explanation of Policy Changes:

a. Chapter 4:

(1) Paragraph 4.25, Table 4-1. In the last row of the Facility column, added “VGSI” after “Communications”. Deleted APM row from table; APM inspections will be conducted as a “by request” Special Inspection.

(2) Paragraph 4.25, Table 4-1, NOTE 5. Clarified periodic requirements for RNAV SIAP(s).

b. Chapter 6, Paragraph 6.15b(3)(b). Added detail and clarification to guidance for night evaluation of runway lighting systems.

c. Chapter 7:

(1) Paragraph 7.12a, NOTE. In the second sentence, changed “should” to “will”.

(2) Paragraph 7.22. Added detail and clarification for night evaluation requirements when a change has been made to lighting systems.

d. Chapter 11:

(1) Paragraph 11.20e. Changed “and changes to the applicable SIAP” to “and applicable changes to the final approach segment”.

(2) Paragraph 11.51, Checklist. Deleted “X” under “Periodic Inspection” for “VOT Reference Point”.

(3) Paragraph 11.60, VOT Tolerances. Under the Periodic Inspection (P) column for the Alignment Parameter, deleted the X that indicates 0.0° and inserted an X to indicate 1.0° or less.

e. Chapter 13:

(1) Paragraph 13.12a, Checklist, NOTE 3. Deleted the words “public RNAV” and inserted “RNAV-based”.

(2) Paragraph 13.33a and b. Deleted “(“Type A”)” and “(“Type B”)” references, as they are no longer charted. Deleted “may” in subparagraph b, as the 1 nm performance is required.

Page 2 Par 4

(3) Paragraph 13.40. Clarified guidance for LP/ LPV WAAS RNAV procedures.

(4) Paragraph 13.42. Clarified guidance for LP/ LPV WAAS RNAV procedures.

(5) Paragraph 13.42c. Changed to read, “(b) Confirm WAAS glidepath full scale fly-up.” Clarified LP/ LPV guidance when encountering WAAS interference.

(6) Paragraph 13.44, Table 13-2. Footnote (1) added to identify Glide Path Alignment and Threshold Crossing Height as not applicable to LP; LP does not provide vertical guidance. Table 13-3. Added SNR-W parameter and tolerance.

f. Chapter 14:

(1) Paragraph 14.10c. In the last line, changed “general terrain map” to “general terrain monitor”.

(2) Paragraph 14.10c(1). Changed first two sentences to more accurately describe General Terrain Monitor (GTM) characteristics.

(3) Paragraph 14.11c, 2nd paragraph. Delete 2nd and 3rd sentences. The referenced website is no longer available.

(4) Paragraph 14.13, Checklist. Deleted “- GTM” from “MSAW – GTM” in last line and replaced Footnote (2). The change replaces the previous practice of scheduling periodic APM(s) with standard instrument approach procedures and leave the requirement to check GTM functionality during both commissioning and periodic ASR flight inspections.

(5) Paragraph 14.14t(2). Replaced “General Terrain Map (GTM)” with “General Terrain Monitor (GTM)”.

(6) Paragraph 14.23a, GENERIC PAR Checklist. Made the following changes to the checklist:

under “AC EL”.

(a)

(b)

(c)

Added “(3)” in the Inspection column next to “AC AZ”.

Added “(3)” in the Inspection Column next to “AC EL”.

Added an “X” in the “Approach #1” row under “AC AZ” and another

(d)

(e)

Added an “X” in the “Approach #2” row under “AC AZ”.

Added a third note under the checklist that reads, “(3) Apply commissioning tolerances when conducting a special inspection for antenna change (AZ or EL)”.

(7) Paragraph 14.23b, GPN-22, TPN-25 Checklist. Made the following changes to the checklist:

(a) In the Inspection column for “AC AZ”, changed it to read “AC” and add a “(9)” next to it.

(b) Added an “X” in the “Approach #3” row under the new “AC” heading.

Par 5 Page 3

(c) Added an “X” in the “Approach #4” row under the new “AC” heading.

(d) Added an “X” in the “Alternate Angle” row under the new “AC” heading.

(e) Deleted the entire “AC EL” column.

(f) Added a ninth note under checklist note (8) on Page 14-28, that reads,

“(9) Apply commissioning tolerances when conducting a special inspection for antenna change. These types of PAR(s) do not have separate AZ and EL antennas.”

(8) Paragraph 14.23d, MPN-25, TPN-31, FPN-67 (U.S. Army), GCA-2000 Checklist. Made the following changes to the checklist:

(a) Added “(4)” in the Inspection column next to “AC AZ”.

(b) Added “(4)” in the Inspection column next to “AC EL”.

under “AC EL”.

(c) Added an “X” in the “Normal Approach” row under “AC AZ” and another

(d) Added an “X” in the “Lower Safe” row under “AC AZ”.

(e) Added a fourth note under the checklist that reads, “(4) Apply commissioning tolerances when conducting a special inspection for antenna change (AZ or EL).”

(9) Paragraph 14.16, Figure 14-5, Tolerances. Corrected errors in foot conversion to nautical miles in Footnotes (1) and (2).

g. Chapter 15. References to “FICO Technical Services Sub-Team (TSS)” changed to “Flight Inspection Policy”.

(1) Paragraph 15.10b. Office responsible for researching ILS facilities for higher category service updated.

(2) Paragraph 15.12a(7). Office responsible for researching ILS facility history for restriction removal updated.

(3) Paragraph 15.12b, Standby Equipment – Localizer/ Glide Slope. U.S. Army and U.S. Navy/ Marine Corps added to facility types.

(4) Paragraph 15.12h(5), Capture Effect Glide Slope. Corrected Measurements Required.

(5) Paragraph 15.20g(1), NOTE. U.S. Army and U.S. Navy/ Marine Corps added to facility types and reference to Order VN200 8240.52 changed to TI 8200.52.

(6) Paragraph 15.20g(2), Roll-Out Procedures. Deleted “at Part 139 airports”.

Page 4 Par 5

(7) Paragraph 15.20g(2)(a), Site, Commissioning, Reconfiguration, and Categorization Inspections. Office responsible for researching ILS facility history for restriction removal update.

(8) Paragraph 15.20g(2)(b), Periodic or Special Inspections which require Structure Analysis. Office responsible for researching ILS facility history for restriction removal updated.

(9) Paragraph 15.30f(1), Approved Procedures – Level Run. Altitude limitation and adjustment guidance added.

(10) Paragraph 15.51f, NOTE. U.S. Army and U.S. Navy/ Marine Corps added to facility types.

(11) Paragraph 15.51f(1), Reference Values. U.S. Army and U.S. Navy/ Marine Corps added to facility types.

(12) Paragraphs 15.52a, 15.52b, and 15.52c, 75 MHz Marker Analysis. Corrected figure reference.

(13) Paragraph 15.52, Figure 15-9B. Corrected figure reference.

(14) Paragraph 15.60a, Localizers. U.S. Army and U.S. Navy/ Marine Corps added to facility types.

h. Appendix 1: On Page A1-16, added definition for Localizer Performance (LP) and clarified definition for Localizer Performance with Vertical Guidance (LPV). On Page A1­ 17, replaced definition of MSAW Approach Path Monitor (APM), replaced “MSAW General Terrain Map (GTM)” with “MSAW General Terrain Monitor (GTM)”, and replaced the definition of MSAW GTM. On Page A1-33, corrected acronym “GTM”.

i. Appendix 2:

(1) Paragraph A2.11b. Changed “should” to “must not be rounded off to an in-tolerance condition” when value exceeds a tolerance.

(2) Paragraph A2.15c. Moved parentheses to include Log in E1/ E2 computation, to match TI 8240.52.

Par 6 Page 5

6. Disposal of Transmittal. After filing the revised pages, the change transmittal should be retained.

PAGE CONTROL CHART

REMOVE PAGES DATED INSERT PAGES DATED

4-9 02/01/07 4-9 9/14/09 4-10 10/01/05 4-10 10/01/05 4-13 10/01/05 4-13 10/01/05 4-14 02/01/07 4-14 9/14/09 4-15 02/01/07 4-15 9/14/09 4-16 10/01/05 4-16 10/01/05 6-7 10/01/05 6-7 10/01/05 6-8 10/01/05 6-8 9/14/09 7-5 02/01/07 7-5 9/14/09 7-6 02/01/07 7-6 02/01/07 7-23 02/01/07 7-23 02/01/07 7-24 10/01/05 7-24 9/14/09 11-5 02/01/07 11-5 9/14/09 11-6 02/01/07 11-6 02/01/07 11-21 02/01/07 11-21 02/01/07 11-22 02/01/07 11-22 9/14/09 11-31 02/01/07 11-31 02/01/07 11-32 02/01/07 11-32 9/14/09 13-3 02/01/07 13-3 9/14/09 13-4 10/01/05 13-4 10/01/05 13-11 02/01/07 13-11 9/14/09 13-12 02/01/07 13-12 9/14/09 13-13 02/01/07 13-13 9/14/09 13-14 02/01/07 13-14 9/14/09 13-15 02/01/07 13-15 9/14/09 13-16 02/01/07 13-16 9/14/09 13-17 (and 18) 02/01/07 13-17 (and 18) 9/14/09

Page 6 Par 6

PAGE CONTROL CHART

(continued)

REMOVE PAGES DATED INSERT PAGES DATED

14-1 02/01/07 14-1 9/14/09 14-2 10/01/05 14-2 9/14/09 14-5 02/01/07 14-5 9/14/09 14-6 02/01/07 14-6 02/01/07 14-7 10/01/05 14-7 9/14/09 14-8 10/01/05 14-8 10/01/05 14-19 02/01/07 14-19 02/01/07 14-20 02/01/07 14-20 9/14/09 14-21 10/01/05 14-21 10/01/05 14-22 10/01/05 14-22 9/14/09 14-25 02/01/07 14-25 02/01/07 14-26 02/01/07 14-26 9/14/09 14-27 10/01/05 14-27 9/14/09 14-28 02/01/07 14-28 9/14/09 14-31 02/01/07 14-31 9/14/09 14-32 02/01/07 14-32 02/01/07 15-1 02/01/07 15-1 9/14/09 15-2 10/01/05 15-2 10/01/05 15-9 02/01/07 15-9 9/14/09 15-10 02/01/07 15-10 02/01/07 15-19 10/0/1/05 15-19 10/01/05 15-20 02/01/07 15-20 9/14/09 15-31 02/01/07 15-31 02/01/07 15-32 02/01/07 15-32 9/14/09 15-33 02/01/07 15-33 9/14/09 15-34 02/01/07 15-34 9/14/09 15-35 02/01/07 15-35 9/14/09 15-36 02/01/07 15-36 9/14/09 15-55 02/01/07 15-55 9/14/09 15-56 02/01/07 15-56 02/01/07

Par 6 Page 7

PAGE CONTROL CHART

(continued)

REMOVE PAGES DATED INSERT PAGES DATED

15-69 02/01/07 15-69 9/14/09 15-70 02/01/07 15-70 02/01/07 15-73 02/01/07 15-73 9/14/09 15-74 02/01/07 15-74 02/01/07 15-77 02/01/07 15-77 02/01/07 15-78 02/01/07 15-78 9/14/09 A1-15 10/01/05 A1-15 10/01/05 A1-16 02/01/07 A1-16 9/14/09 A1-17 10/01/05 A1-17 9/14/09 A1-18 10/01/05 A1-18 9/14/09 A1-33 02/01/07 A1-33 9/14/09 A1-34 02/01/07 A1-34 02/01/07 A2-1 01/01/05 A2-1 9/14/09 A2-2 10/01/05 A2-2 10/01/05 A2-5 10/01/05 A2-5 9/14/09 A2-6 10/01/05 A2-6 10/01/05 /s/ Thomas C. Accardi Director of Aviation System Standards

Page 8 Par 6

Chg 1 Cover

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION CHG 1 to

8200.1C

02/01/07

SUBJ: United States Standard Flight Inspection Manual

1. PURPOSE. This change transmits revisions to the United States Standard Flight Inspection Manual (USSFIM), FAA Order 8200.1C Department of the Army Technical Manual TM 95-225, Department of the Navy Manual NAVAIR 16-1-520, and Department of the Air Force Manual AFMAN 11-225, dated October 1, 2005.

2. DISTRIBUTION. This change is distributed to selected offices on special mailing list ZVN­ 820. It is available on the Internet (http://www.avn.faa.gov). Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

3. EFFECTIVE DATE. This order is effective March 1, 2007.

4. CANCELLATIONS. The following Notices are canceled:

a. N 8200.85, Interim Changes to FAA Order 8200.1C, dated December 1, 2005.

b. N 8200.87, Elimination of Periodic Inspections of Public RNAV SIAP(s) (FAA Order 8200.1C), dated March 20, 2006.

c. N 8200.90, Low and Medium Frequency Non-directional Beacons (NDB(s)), FAA Order 8200.1C, Chapter 12, dated May 15, 2006.

d. N 8200.91, Interim Change to FAA Order 8200.1C, Chapter 4, dated June 12, 2006.

e. N 8200.92, Interim Change to FAA Order 8200.1C, Chapter 11, Rho and Theta Systems, dated June 20, 2006.

f. N 8200.94, Interim Changes to Update FAA Order 8200.1C, dated July 25, 2006.

g. N 8200.95, Change to N 8200.94, Attachment (FAA Order 8200.1C, Chapter 15, dated August 22, 2006.

h. N 8200.96, Change to Precision Approach Radar Flight Inspection Requirements, FAA Order 8200.1C, Chapter, 14, dated September 1, 2006.

Distribution: Special Addressees Initiated By: Air Traffic Operations (ATO-W)

Aviation System Standards Flight Inspection Operations Flight Inspection Policy (AJW-3310)

i. N 8200.99, Elimination of Periodic Flight Inspection of VGSI Systems (FAA Order 8200.1C), dated December 15, 2006.

j. N VN200 8200.21, Flight Inspection of RNAV Course-to-Fix (CF) and Holding, dated February 1, 2007.

k. N VN200 8200.22, Flight Inspection of RADAR Vector to Area Navigation (RNAV) Route, dated February 1, 2006.

l. N VN200 8200.27, ROC Check and SIAP Inspection Guidance, dated April 10, 2006.

m. N VN200 8200.31, PAR/ VGSI Recordings, dated June 28, 2006.

5. EXPLANATION OF CHANGES:

a. Chapter 4:

(1) Paragraphs 4.15b and 4.35d. Title of FAA Order 8240.36 changed to read, “Flight Inspection Report Processing System”.

(2) Paragraph 4.20a, first paragraph, last sentence. Changed to read, “The next inspection will be predicated upon the actual date of completion” to reflect guidance from Notice 8200.91.

(3) Paragraph 4.24a(2). “Airway Facilities” changed to “Air Traffic Technical Operations”.

(4) Paragraph 4.25. VGSI interval deleted from Table 4-2. No longer a requirement. Note (5) changed.

b. Chapter 5:

(1) Paragraph 5.12a, b, c, and g(2). Added “General” instructions. Deleted the “Flight Data Center (FDC) NOTAM(s)” paragraph. Reorganized the information in the “Facility NOTAM(s)” and “Instrument Flight Procedures” paragraphs. Directions were updated to match current offices and policies. More detail was added to the paragraph concerned with initiating NOTAM(s) for military facilities and/or instrument procedures.

(2) Paragraph 5.21. Removed requirement to retain source material for PAR, VGSI, and NDB inspections once the report has been archived. Added requirement to archive data logger files for all inspections utilizing AFIS, when conducted with a functioning data logger.

(3) Paragraph 5.22. Title of FAA Order 8240.36 changed to read, “Flight Inspection Report Processing System”.

Page 2 Par 4

c. Chapter 6. Paragraph 6.13, Checklist. Note 2 added, “Public RNAV SIAP(s) have no periodic inspection requirement; however, a periodic obstacle verification must still be completed for the runway(s) serviced.” Note 2 added in the Periodic column for Final Approach Segment, Missed Approach Segment, and Obstacle Verification. (N 8200.87)

d. Chapter 7:

(1) Paragraph 7.12a:

(a) Last sentence. Document for facility data submission has changed from FAA Order 8240.36, Instructions for Flight Inspection Reporting, to FAA Order 8240.52, Aeronautical Data Management.

(b) Removed VGSI Periodic checklist requirements and supporting notes.

(2) Paragraph 7.12b(2)(c)1. Changed requirement to allow level run method to be used to determine the path angle of all VGSI types.

(3) Paragraphs 7.12b(2)(c)2. Requirement of On-Path Method for commissioning type inspection of PAPI removed. Level run method may be used. On-Path Method should be used to confirm questionable Level Run results. Minimum pair of light color change data for On-Path Method changed from four to three.

(4) Paragraph 7.12k. Added information for Omni-directional Runway End Identifier Lights (OD REIL).

(5) Paragraph 7.22d. Added flashing rate for OD REIL, 60 flashes per minute.

e. Chapter 11:

(1) Paragraph 11.12. Dedicated VOT checklist established in Paragraph 11.51.

(a) Footnote (13) added. ESV(s) must be revalidated any time a coverage orbit is required by this order.

(b) Footnote (14) added. VOT periodic requirements may be performed on the ground or in the air within the areas approved for use.

(2) Paragraph 11.20. Formatting change moves previous “Detailed Procedures” from Paragraph 11.21 to “Flight Inspection Specifications” in Paragraph 11.20.

(3) Paragraph 11.20e(2), 3rd sentence. Added frequency change as requirement to check VOR radials 5 either side of the approach radials and TACAN null checks.

(4) Paragraph 11.20f, 3rd sentence. Added frequency change as requirement for orbit evaluation.

(5) Paragraph 11.20h(1)(d) 1 and 2. Deleted 1 Airport Surface Markings and 2 Signs. Information included in Order VN 200 8240.52.

Par 5 Page 3

(6) Paragraph 11.33, COVERAGE. In the 2nd sentence, after “Stand-alone DME fixes,” added “located outside the FISSV.”

(7) Paragraph 11.41. Changed from “Detailed Procedures” to “Flight Inspection Specifications”.

(8) Paragraph 11.41l(9) Demand Mode. (Reserved) deleted. No planned use of this paragraph is expected.

(9) Paragraph 11.60c, DME Tolerances. Added Unlock information for Approach and En Route Radials to the Coverage parameter.

f. Chapter 12. Renumbered and reorganized major paragraphs. Deleted “Preflight Requirements”, “Analysis”, and “Adjustments” paragraphs. Added “Maintenance Actions Requiring Flight Inspection” and “Reporting” paragraphs. Divided into two Sections, “General” and “Flight Inspection Tolerances”.

(1) Paragraph 12.10. Added details to NDB classifications and added information about NDB identification signals.

(2) Paragraph 12.11. Renamed “Flight Inspection Specifications”. Contents include the inspection checklist and detailed specifications for each item. Made the following changes to the Checklist: Added columns for Antenna Change and Frequency Change. Deleted row labeled “Coverage” and inserted two new rows in its place labeled, “Coverage Orbit” and “Routes and Transitions”. Deleted the existing footnotes. Added new footnotes.

(3) Paragraph 12.12. Deleted “Flight Inspection Procedures” and renamed “Maintenance Actions Requiring Flight Inspection”. Added information about maintenance requiring flight inspections.

(4) Paragraph 12.13. Deleted “Analysis” and renamed “Flight Inspection Procedures”. Expanded directions for Identification and Voice. Deleted Coverage paragraph and replaced with Coverage Orbit; added 30 maximum when switching transmitters during coverage orbit. Changed SIAP paragraph to “Instrument Flight Procedures” with expanded directions. Added ESV paragraph. Added specific directions for standby power. Added new paragraph for Special Inspections, including directions for Antenna Change, Transmitter Change, and Frequency Change inspections.

(5) Paragraph 12.14. Moved “Tolerances” to Section 2, renamed “Reporting.”. Added instructions for reporting inspection results.

(6) Paragraph 12.15. Deleted “Adjustments.”

(7) Paragraph 12.20. Added Section 2, paragraph titled “Tolerances.” Added tolerance for holding patterns in Paragraphs 12.20d and 12.20e(2).

Page 4 Par 5

g. Chapter 13:

(1) Paragraph 13.11d. Incorporated Notice VN200 8200.21.

(2) Paragraph 13.12a. Checklist. Added Note 3, regarding periodic inspection of Public RNAV LPV procedures”. “(3)” added to “P” in header of right column. (N 8200.87)

(3) Paragraph 13.13. Deleted reference to NFD. Changed “Resource and Data Management” to “Flight Inspection Policy”.

(4) Paragraph 13.21. Added FAA Order 8260.52.

(5) Paragraph 13.32a. Added Figure 1, SID Overview and Pilot Navigation Area Arc Radius information. Incorporated Notice VN200 8200.22.

(6) Paragraph 13.33. Substituted “RNAV 2” for “Type A” and “RNAV 1” for “Type B”, per AC 90-100 and charting to be effective February 2007. This change is due to the terms being changed in AC 90-100, which is aligning with ICAO terminology. AC 90-100A publication will be first quarter 2007.

(7) Paragraph 13.34. Added note 1 to DME Accuracy parameter (Notice VN200 8200.20).

(8) Paragraph 13.40. Changed HAT value supported from  250 ft to  200 ft (FAA Administrator announcement WAAS to 200 feet.

(9) Paragraph 13.42a, Checklist. Added Note 2, regarding periodic inspection of Public RNAV LPV procedures”. “(2)” added next to “P” in header of right column. (N 8200.87)

(10) Table 13-1. Added Note 2 regarding SNR from a WAAS GEO (Notice VN200 8200.23).

(11) Table 13-2. Changed WAAS Vertical Protection Level to include approach minima down to 200 feet.

h. Chapter 14:

(1) Paragraph 14.14q. Two sentences inserted following the first sentence. Allows UHF coverage to be confirmed by targets of opportunity. Minimizes impact after King Air fleet no longer has UHF capability.

(2) Paragraph 14.22. Changed from “Flight Inspection Procedures” to “Flight Inspection Specifications.”

Par 5 Page 5

(3) Paragraph 14.23a, Checklist for Generic PAR. Added requirement to checklist for Standby Transmitter to inspect both the A and B Cursors.

(4) Paragraph 14.23b, Checklist for GPN-22, TPN-25. Further explanation added to Note (5)(b).”

(5) Paragraph 14.23c, Checklist for TPN-22. Deleted all the text associated with “TPN-22 CONTROLLER INSTRUCTIONS.” Not relevant to flight inspection.

(6) Paragraph 14.23d, Checklist for MPN-25, TPN-31, FPN-67 (U.S. Army), GCA-2000. Added note to clarify Standby Transmitter inspection requirements.

(7) Paragraph 14.24. Changed from “Detailed Procedures” to “Flight Inspection Procedures.”

(8) Paragraph 14.24m. Two sentences inserted following the first sentence. Allows UHF coverage to be confirmed by targets of opportunity. Minimizes impact after King Air fleet no longer has UHF capability.

i. Chapter 15:

(1) Paragraph 15.10.b, NOTE deleted. No longer applicable, as single transmitter facilities are acceptable, provided they meet the Level 2 performance requirements. Updated new office name.

(2) Paragraph 15.12a(7). Updated new office name.

(3) Paragraph 15.12b. Added clarification to Standby Transmitter for Order 6750.49A, Change 5, Equality in Normal.

(4) Paragraphs 15.12h(1), (2), (3), (4), (5), and (7). Checklist changes made implementing Change 5 to FAA Order 6750.49A, per Notice 8200.88. Allows monitors to be checked on one transmitter only when facility is maintained using FAA Order 6750.49A.

(5) Para 15.12j(15). NOTAM Example for PAPI restriction corrected.

(6) Paragraph 15.20b. Replaced term LCA with specified altitude.

(7) Paragraph 15.20b. NOTE * Clarification of Installed added.

(8) Paragraph 15.20e. Replaced term LCA with procedural altitude.

(9) Paragraph 15.20f. Replaced term LCA with specified altitude.

(10) Paragraph 15.20g(1)(e). Added requirement to use Differential GPS AFIS “truth system” to determine alignment during commissioning-type inspections of LDA(s) where adequate visual checkpoints are not available. Clarified the use of Satisfactory (S) or Unsatisfactory (U) during a periodic when AFIS updates are impractical.

(11) Paragraph 15.20g(2). Corrected reference paragraph. Updated new office names.

Page 6 Par 5

(12) Paragraph 15.20j. Replaced term LCA with specified altitudes.

(13) Paragraph 15.20k. Replaced term LCA with specified altitude. Corrected flow chart.

(14) Paragraph 15.20m. Replaced term LCA with specified altitude.

(15) Paragraph 15.30f. The level run altitude changed from GSI to an ICAO Standards and Recommended Practice (SARPS) of 1,500 feet. True altitude is added to compensate for temperature and altimeter with the intent that the height flown above the facility will remain the same from inspection to inspection. Requirement added to document the established level run altitude using Form VN200 8240-20. This will require the flight crew to submit a change to the AVNIS data sheet remark until all glide slopes have an established level run altitude documented. For reporting purposes on the ILS report (FAA Form 8240­ 8) and Form VN200 8240-20, report the established true altitude. For example, if the level run altitude is established at 2,500 ft true altitude and it was corrected to an indicated altitude of 2,449 ft, the established level run altitude documented on the data sheet and the reported level run altitude would both be 2,500 ft.

(16) Paragraph 15.30f(4). Replaced term GSI with established level run altitude.

(17) Paragraph 15.30i. Replaced GSI altitude with established level run altitude.

(18) Paragraph 15.30n. Replaced LCA with an altitude equal to 0.45 times the commissioned angle at 10 nm. Aligned policy with ICAO SARPS.

(19) Paragraph 15.51b. Added clarification of Rate of Change Reversal.

(20) Paragraph 15.51c(1)(c). Removed 10µA linearity tolerance per recommendations from third party engineering perspective.

(21) Paragraph 15.51c(2)(b). Replaced term LCA.

(22) Paragraph 15.51c(3)(a). Removed reference to “Point C”.

(23) Paragraph 15.51e. Corrected duplication of paragraphs by creating separate “CAT III Adjust and Maintain” paragraph. Renumbered remaining paragraphs under “ILS Maintenance Reference Tolerances and Alerts”, 15.51f and 15.51g.

(24) Paragraph 15.51f(1)(a)8, previously 15.51e(2)(a)8. Moved old paragraph to Order VN200 8240.52. Inserted text from previous Paragraph 15.51e(2)(a)9.

(25) Paragraph 15.51f(1)(a)9, previously 15.51e(2)(a)10. Implements Change 5 to FAA Order 6750.49A, per Notice 8200.88. Provides instructions for dual transmitter facilities when unable to meet equality limits.

(26) Paragraph 15.51f(2)(c), previously 15.51e(3)(c). Added emphasis for the flight inspector to issue a Maintenance Alert when a value exceeds the “adjust and maintain” limits.

Par 5 Page 7

(27) Previous Figure 15-8, Required Airborne Measurements per Facility Type, moved to Order VN200 8240.25.

(28) Paragraph 15.60a. Corrected alignment tolerance for independently monitored back courses from =8A to = 10A.

(29) Paragraph 15.60b. Corrected reference for Reference Datum Height (RDH).

(30) Previous Paragraphs 15.60c and d. Reference tolerance paragraphs moved to Order VN200 8240.52. Reference tolerances updated, per Notice 8200.88.

j. Chapter 16:

(1) Paragraph 16.20b(2)(b). Redefined positioning for checking vertical coverage.

(2) Paragraph 16.34e(4), Azimuth Collocated with Elevation Checklist: PFE Maximum Tolerance changed from “0.30” to“0.50.” Corrects previous typographical error.

(3) Paragraph 16.34e(5), Elevation Checklist: PFE Maximums Tolerance changed from “0.20” to “0.30.” Per Notice 8200.80, this is based on a typical Collocated MMLS installation located 1.0 nm from the published Missed Approach Point/ Decision Height, the tolerance change represents an increased allowable aircraft vertical position error, from 21 ft. to 32 ft.

k. Chapter 22:

(1) Paragraph 22.11b(2)(a). Deleted Note 1. The altitude to verify ESV is 0.45 times the commissioned angle at the ESV distance. 150µA or greater is required at an altitude equal to 0.45 times the commissioned angle at the ESV distance.

(2) Paragraph 22.11f. Updates descriptions of RNAV PRO, AFIS DME/ DME mode operation and reporting ESV results. Requires the inspection to be terminated if a DME designated as critical is off the air, or when there are 3 or less DME(s) to be evaluated and 1 of the 3 is out of service.

l. Chapter 24:

(1) Paragraph 24.21. Paragraph c added, “RNAV SIAP(s). RNAV and satellite-based SIAP(s) have no periodic inspection requirement, except obstacle verification. The periodic requirement to conduct obstacle verification may be evaluated independent of a SIAP inspection.” (N 8200.87)

(2) Paragraph 24.40. Changes ILS inspection requirements to include SBP, width and symmetry, and provides an exception for glide slope clearance checks during subsequent inspections of the same facility.

Page 8 Par 5

m. Appendix 1:

(1) Updated definition of Critical DME per latest AC 90-100.

(2) Deleted LCA definition which no longer exists per LCA discussions about using ICAO definition.

(3) Added definitions for ILS-Glidepath Rate of Change, ILS-Glidepath Reversal, ILS-Half ILS Glidepath Sector, HLOM, and MLOM.

6. DISPOSAL OF TRANSMITTAL. After filing the revised pages, the change transmittal should be retained.

PAGE CONTROL CHART

REMOVE PAGES DATED INSERT PAGES DATED

4-3 10/01/05 4-3 10/01/05 4-4 10/01/05 4-4 02/01/07 4-5 10/01/05 4-5 02/01/07 4-6 10/01/05 4-6 02/01/07 4-7 10/01/05 4-7 10/01/05 4-8 10/01/05 4-8 02/01/07 4-9 10/01/05 4-9 02/01/07 4-10 10/01/05 4-10 10/01/05 4-13 10/01/05 4-13 10/01/05 4-14 10/01/05 4-14 02/01/07 4-15 10/01/05 4-15 02/01/07 4-16 10/01/05 4-16 10/01/05 5-i (and ii) 10/01/05 5-i (and ii) 02/01/07 5-1 10/01/05 5-1 10/01/05 5-2 10/01/05 5-2 02/01/07 5-3 10/01/05 5-3 02/01/07 5-4 10/01/05 5-4 10/01/05 5-5 10/01/05 5-5 10/01/05 5-6 10/01/05 5-6 02/01/07 5-7 10/01/05 5-7 02/01/07 5-8 10/01/05 5-8 02/01/07 6-3 10/01/05 6-3 10/01/05 6-4 10/01/05 6-4 02/01/07

Par 5 Page 9

PAGE CONTROL CHART

(continued)

REMOVE PAGES DATED INSERT PAGES DATED

7-iii (and iv) 10/01/05 7-iii (and iv) 02/01/07 7-5 thru 7-7 01/01/05 7-5 thru 7-7 02/01/07 7-8 10/01/05 7-8 10/01/05 7-23 thru 7-29 (and 30) 10/01/05 7-23 thru 7-30 02/01/07 11-i thru 11-37 (and 38) 10/01/05 11-i thru 11-32 02/01/07 12-i thru 12-8 10/01/05 12-i thru 12-8 02/01/07 13-i and ii 10/01/05 13-i and ii 02/01/07 13-1 10/01/05 13-1 10/01/05 13-2 10/01/05 13-2 02/01/07 13-3 10/01/05 13-3 02/01/07 13-4 10/01/05 13-4 10/01/05 13-5 thru 13-15 (and 16) 10/01/05 13-5 thru 13-17 (and 18) 02/01/07 14-iii (and iv) 10/01/05 14-iii (and iv) 02/01/07 14-1 10/01/05 14-1 02/01/07 14-2 10/01/05 14-2 10/01/05 14-5 thru 6 10/01/05 14-5 thru 6 02/01/07 14-9 10/01/05 14-9 02/01/07 14-10 10/01/05 14-10 10/01/05 14-19 10/01/05 14-19 02/01/07 14-20 10/01/05 14-20 10/01/05 14-25 thru 14-26 10/01/05 14-25 02/01/07 14-27 10/01/05 14-27 10/01/05 14-28 thru 14-39 (and 40) 10/01/05 14-28 thru 14-38 02/01/07 15-i - iv 10/01/05 15-i - iv 02/01/07 15-1 10/01/05 15-1 02/01/07 15-2 10/01/05 15-2 10/01/05 15-9 thru 15-18 10/01/05 15-9 thru 15-18 02/01/07 15-19 10/01/05 15-19 10/01/05 15-20 100105 15-20 02/01/07 15-21 10/01/05 15-21 10/01/05 15-22 10/01/05 15-22 02/01/07 15-23 10/01/05 15-23 10/01/05

Page 10 Par 6

PAGE CONTROL CHART

(continued)

REMOVE PAGES DATED INSERT PAGES DATED

15-24 thru 25 10/01/05 15-24 thru 25 02/01/07 15-26 thru 27 10/01/05 15-26 thru 27 10/01/05 15-28 thru 37 10/01/05 15-28 thru 37 02/01/07 15-38 10/01/05 15-38 10/01/05 15-39 thru 90 10/01/05 15-39 thru 15-82 02/01/07 16-9 10/01/05 16-9 02/01/07 16-10 10/01/05 16-10 10/01/05 16-23 10/01/05 16-23 10/01/05 16-24 10/01/05 16-24 02/01/07 16-31 10/01/05 16-31 10/01/05 16-32 10/01/05 16-32 02/01/07 16-33 10/01/05 16-33 02/01/07 16-34 10/01/05 16-34 10/01/05 22-3 10/01/05 22-3 10/01/05 22-4 10/01/05 22-4 02/01/07 22-5 10/01/05 02/01/07 22-6 10/01/05 10/01/05 22-7 thru 9 (and 10) 10/01/05 02/01/07 24-3 10/01/05 24-3 02/01/07 24-4 10/01/05 24-4 10/01/05 24-7 10/01/05 24-7 02/01/07 24-8 10/01/05 24-8 10/01/05 A1-5 10/01/05 A1-5 10/01/05 A1-6 10/01/05 A1-6 02/01/07 A1-7 10/01/05 A1-7 02/01/07 A1-8 10/01/05 A1-8 10/01/05 A1-9 10/01/05 A1-9 10/01/05 A1-10 thru A1-12 10/01/05 A1-10 thru A1-12 02/01/07 A1-15 10/01/05 A1-15 10/01/06 A1-16 10/01/05 A1-16 02/01/07

Par 6 Page 11

PAGE CONTROL CHART

(continued)

REMOVE PAGES DATED INSERT PAGES DATED

A1-33 10/01/05 A1-33 02/01/07 A1-34 10/01/05 A1-34 02/01/07 A1-35 10/01/05 A1-35 02/01/07 A1-36 10/01/05 A1-36 02/01/07 /s/ Thomas C. Accardi Director of Aviation System Standards

Page 12 Par 6

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION ORDER

Foreward

8200.1C

10/01/05 SUBJ: United States Standard Flight Inspection Manual (USSFIM)

The purpose of this order is to prescribe standardized procedures for flight inspection of air navigation services. It is not intended as authorization for an agency to assume flight inspection authority over any group of services which are not now under its jurisdiction. Similarly, it carries no designation of responsibility within any agency unless such has been so designated in its usual procedural manner, such as general orders, regulations, etc.

This order is directive upon all personnel charged with the responsibility for execution of the flight inspection mission, when such personnel or organization is so designated by its agency. Compliance with this order, however, is not a substitute for common sense and sound judgment. Nothing in this order will be construed to relieve flight inspection crews or supervisory personnel of the responsibility of exercising initiative in the execution of the mission, or from taking such emergency action as the situation warrants.

The Federal Aviation Administration will coordinate and provide approved changes to this order by means of a page revision method. Revised pages will be transmitted by a Federal Aviation Administration Change or Notice. Recommendations concerning changes or additions to the subject material are welcomed and should be forwarded to one of the following addresses:

U.S. Army: Headquarters, Department of the Army, Office of the Deputy Chief of Staff, G-3/5/7, (DAMO-OD-A) Commander, United States Army Aeronautical Services Agency, 9325 Gunston Road, Building 1466, Suite N319, Fort Belvoir, Virginia 22060­ 5582

US Navy: Office of the Chief of Naval Operations (N785F), 2000 Navy Pentagon, Washington DC 20350-2000

US Air Force: Commander, Air Force Flight Standards Agency, 1535 Command Drive Suite D308, Andrews AFB MD 20331-7002

FAA: Director of Aviation System Standards, PO Box 20582, Oklahoma City OK 73125

Page i

8200.1C 10/01/05

This order of Flight Inspection Procedures has been officially approved by:

US Army: Headquarters, Department of the Army, Deputy Chief of Staff, G-3/5/7 US Navy: Chief of Naval Operations, U.S. Navy US Air Force: Chief of Staff, U.S. Air Force FAA: Director of Aviation System Standards /s/ Thomas C. Accardi Director of Aviation System Standards Federal Aviation Administration

Page ii

TOC

10/01/05 8200.1C

TABLE OF CONTENTS

Chapter Title Page

Chapter 1 Introduction … 1-1

Chapter 2 Flight Inspector’s Authority and Responsibilities … 2-1

Chapter 3 Special Requirements … 3-1

Chapter 4 Flight Inspection Types, Priorities, Intervals, Procedures … 4-1

Chapter 5 Facility Status Classification, Notices to Airman (NOTAM), Records, and Reports … 5-1

Chapters 9 – 10 … Reserved

Chapters 18 – 19 … Reserved

Chapter 21 Helicopter … Reserved

Chapter 22 Flight Inspection of Expanded Service Volume (ESV)

Chapter 6 Flight Inspection of Instrument Flight Procedures … 6-1

Chapter 7 Lighting Systems … 7-1

Chapter 8 Communications … 8-1

Chapter 11 Rho and Theta Systems … 11-1

Chapter 12 Low and Medium Frequency Nondirectional Beacons (NDB) … 12-1

Chapter 13 Area Navigation (RNAV) … 13-1

Chapter 14 Radar … 14-1

Chapter 15 Instrument Landing System (ILS) … 15-1

Chapter 16 Microwave Landing System (MLS) … 16-1

Chapter 17 Local Area Augmentation System (LAAS) … 17-1

Chapter 20 Flight Inspection of VFR Aeronautical Charts … 20-1

For Ground-Based Navigational Aids … 22-1

Chapter 23 Radio Frequency Interference (RFI) Detection … 23-1

Chapter 24 Military Contingency and Natural Disaster Flight Inspection Procedures … 24-1

Appendix 1 Supplemental Information (Glossary, Abbreviations, Acronyms, Symbols) … A1-1

Appendix 2 Formulas … A2-1

Appendix 3 Working Graphs and Charts … A3-1

Appendix 4 Frequency Spectrum … A4-1

Appendix 5 Map Interpretation … A5-1

Appendix 6 UHF Homing Beacons … A6-1

Page iii (and iv)

This Page Intentionally Left Blank.

Chapter 1 - Intro

10/01/05 8200.1C

CHAPTER 1. INTRODUCTION

TABLE OF CONTENTS

Paragraphs Title Pages

1.10 PURPOSE … 1-1

1.11 DISTRIBUTION … 1-1

1.12 EFFECTIVE DATE … 1-1

1.13 CANCELLATIONS … 1-1

1.14 EXPLANATION OF CHANGES … 1-2

1.15 BACKGROUND … 1-7

1.16 DEFINITIONS … 1-9

1.17 UNIT OF MEASUREMENT … 1-9

1.18 IDENTIFYING CHANGES IN THE TEXT OF THIS ORDER … 1-9

1.19 AUTHORITY TO CHANGE THIS ORDER … 1-9

Page 1-i (and ii)

This Page Intentionally Left Blank.

10/01/05 8200.1C

CHAPTER 1. INTRODUCTION

1.10 PURPOSE. This order contains the policy, procedures, and criteria for flight inspection and certification of air navigation services, instrument flight procedures, and FAA VFR Aeronautical Charts. The order applies to the flight inspection of all National Airspace System (NAS) and Department of Defense air navigation services and instrument flight procedures.

1.11 DISTRIBUTION. This order is distributed to selected offices on special mailing list ZVN-820. It is available on the Internet (http://www.avn.faa.gov). Distribution within the Department of Defense is handled by the National Geospatial Intelligence Agency. For the U.S. Air Force, this revision is included in the AF STDPUBs CD-ROM and is available on the Internet (http://afpubs.hq.af.mil/).

1.12 EFFECTIVE DATE. This order is effective October 15, 2005.

1.13 CANCELLATIONS

a. The following orders are canceled:

(1) FAA Order 8200.1B, dated .January 2, 2003.

(2) FAA Order 8200.1B, Change 1, dated April 1, 2003.

(3) FAA Order 8200.1B, Change 2, dated June 21, 2004.

b. The following notices are canceled.

(1) N 8200.72, Expanded Service Volume Process, dated October 15, 2004

(2) N 8200.74, Interim Changes to Flight Inspection Requirements, dated October 25, 2004

(3) N8200.75, Interim Change to FAA Order 8200.1B, Section 207, dated October 25, 2004

(4) N 8200.76, Authorization for Portable ILS/ VOR Reciever to Inspect VOTs, dated October 25, 2004

(5) N 8200.77, ILS Supporting Lower than Category I Minima, dated October 25, 2004

(6) N 8200.80, Interim Changes to Flight Inspection Tolerances, dated March 1, 2005

(7) N 8200.83, Visual Glide Slope Indicator (VGSI) Flight Inspection Requirements, dated August 30, 2005

(8) N 8200.84, Frequency of Periodic Flight Inspection, dated August 30, 2005.

(9) N VN200 8200.1, Runway Declared Distance Guidance, dated October 1, 2004

Par 1.10 Page 1-1

8200.1C 10/01/05

(10) N VN200 8200.4, Flight Inspection Frequencies, dated October 1, 2004

(11) N VN200 8200.6, WAAS Supported LNAV/ VNAV dated October 1, 2004

(12) N VN200 8200.7, Flight Inspection of GPS Overlay Procedures When the Primary Facility (e.g., VOR, NDB) is Out of Service (OTS) or Decommissioned, dated October 1, 2004

(13) N VN200 8200.8, ARR/ Orbit Dates, dated October 1, 2004

(14) N VN200 8200.14, Interim Guidance for FAA Order 8200.1, Section 214, dated February 7, 2005

(15) N VN200 8200.17, FAA Order 8200.1, Section 210, dated May 16, 2005.

(16) N VN200 8200.18, FAA Order 8200.1, Section 109, dated June 10, 2005.

1.14 EXPLANATION OF CHANGES. This order has been completely reformatted. It is in one-column format, versus two. The order is divided into chapters, with sections within chapters as necessary, IAW FAA Order 1320.1. Names of offices and organizations changed as a result of reorganization. Paragraph and item references in checklists and tolerance tables changed to reflect new numbering structure.

a. Former Appendix 1, Loran-C, was removed and archived electronically due to inactivity of system.

b. Chapter 2, Flight Inspection Crew Authority & Responsibilities (Formerly Sections 104, 105, and 106). Changed title from “Flight Inspector’s Authority and Responsibilities” to “Flight Inspection Crew Authority and Reponsbilities”.

c. Chapter 4, Section 3, General Flight Inspection Procedures (Formerly Section 106).

(1) Paragraph 4.32. Clarified an Airway Facilities requirement for two-way communications.

(2) Paragraph 4.32a(1). Added requirement to ensure Air Traffic is notified when a facility will be unusable during a flight inspection.

d. Chapter 5, Section 2, Records and Reports (Formerly Section 108). Added requirement to document Airborne Flight Inspection Calibrations.

e. Chapter 6, Flight Inspection of Instrument Flight Procedures (Formerly Section 214). Interim guidance from N VN200 8200.14, Interim Guidance for FAA Order 8200.1, Section 214, added. Reference to obstacle verification for multiple approaches to a runway added. Skipping of a periodic obstacle verification inspection removed. Specific information for flyability removed, to be included in Order VN200 8240.52, Flight Inspection Standard Operating Procedures.

Page 1-2 Par 1.12

10/01/05 8200.1C

f. Chapter 7, Lighting Systems. (Formerly Sections 214 and 218).

(1) Section 1, Visual Glide Slope Indicator (VGSI). Included N 8200.81, Visual Glide Slope Indicator (VGSI) Flight Inspection Requirements, policy in Paragraph 7.12a.. Changed obstacle clearance procedure in Paragraph 7.12f(3). Softened the 1 obstacle clearance tolerance in Paragraph 7.14d.

(2) Section 2, Approach and Runway Lights. Changed title from “Approach Lights” to “Approach and Runway Lights”.

(3) Paragraph 7.20f. Added information to clarify the SSALR operation.

RAIL.

(4) Paragraph 7.20l. Added information to clarify operational use of SFL/

(5) Paragraph 7.22c(3). Added guidance about radio-controlled lighting systems that have a photocell that prevents operation during daylight hours.

(6) Paragraph 7.24a(1). Added, “Light intensity should be checked by pilot control function and controller operation.”

(7) Paragraph 7.24b(1). Added guidance to this tolerance.

g. Chapter 11, Rho Theta Systems (Formerly Sections 201 and 202). Combines all Rho-Theta systems as follows:

Section 2. VHF Omnirange (VOR) Section 3. VOR Test Facility (VOT) Section 4. TACAN Section 5. Distance Measuring Equipment (DME)

ESV information consolidated in Chapter 22. Integrated the use of DGPS truth systems.

(1) Paragraph 11.12, Checklist. Footnote 3 clarifies VOT alignment monitor as maintenance request. Footnote (9) clarifies revalidation of an ESV.

(2) Paragraph 11.21c, En Route Radials. Changed the definition of MOCA to height above obstruction.

(3) Paragraph 11.21f, Orbit Evaluations. Clarifies ARR/ Orbit Date reporting requirements.

(4) Paragraph 11.21i, Detailed Procedures. Clarified primary and standby equipment checks.

Par 1.13 Page 1-3

8200.1C 10/01/05

(5) Paragraph 11.22c, Sensing and Rotation. Clarifies sensing and rotation verification by observation of instrumentation.

(6) Paragraph 11.22e, Polarization. Clarifies polarization is to be checked on one transmitter only.

(7) Paragraph 11.53e(2). Incorporated the use of a PIR for a Periodic or Special VOT inspection and incorporated Notice 8200.76.

h. Chapter 13, RNAV (Formerly Sections 209 and 210). Area Navigation and RNAV WAAS combined into this chapter. Readily available public information removed from introductions. Information duplicated in Chapter 6, Flight Inspection of Instrument Procedures, removed. Avionics specific information duplicated in aircraft manuals removed. RNP levels defined. DME/ DME RNAV analysis and tolerance changed to reflect AFIS software evaluation capability. AFIS software delivered December 2004. AFIS announced data for LPV Glide Path Alignment have been tightened. Representative of precision required for FAS data block. AFIS announced data for LPV Threshold Crossing Height added. AFIS software errors for calculating TCH have been improved. Introduction to LAAS added.

i. Chapter 14, Radar.

(1) Paragraph 14.14t, Minimum Safe Altitude Warning (MSAW). Wording changed to agree with Order VN200 8240.4, Daily Flight Log (DFL), FAA Form 4040-5. Reference to block number removed and replaced with “block title”.

(2) Paragraph 14.23b, GPN-22, TPN-25 Checklist. Added reference 14.24h to Approach 1. Add Periodic requirement to Approach 3.

j. Chapter 15, Instrument Landing System (ILS)(Formerly Sections 217 and 219). ILS and 75 MHz beacons combined into this chapter. Integrated the use of DGPS. Incorporated Rollout guidance. Titles of offices changed due to reorganization. Hazardously Misleading Information (HMI) guidance added.

of Service”.

(1) Paragraph 15.10. Expanded definition of “ILS used for Higher Category

(2) Paragraph 15.12h, Checklists.

(a) Paragraph 15.12h(1), Single Frequency Localizer. Added Footnotes (9) and (10). Added “One XMTR Only” requirement to Clearance Comparability. “Caution: HMI” added to Modulation Equality, Phasing, and Alignment Monitors.

(b) Paragraph 15.12h(2), Dual Frequency Localizer. Added Footnotes (7) and (8). Added “One XMTR Only” requirement to Clearance Comparability. “Caution: HMI” added to Modulation Equality, Phasing, and Alignment Monitors. Changed Course Wide/ Clearance Normal Reference Alarm to MR on Dual Frequency Checklist.

Page 1-4 Par 1.13

10/01/05 8200.1C

(c) Paragraph 15.12h(3), Null Reference Glide Slope. Deleted CBP requirement on standby transmitter. Added Footnote (5). “Caution: HMI” added to Engineering Tests, Modulation Equality, and Phasing. Added “One XMTR Only” requirement to Engineering tests. “CBP One XMTR Only” added to Clearance Checklist Requirement.

(d) Paragraph 15.12h(4), Side Band Reference Glide Slope. Deleted CBP requirement on standby transmitter. Added Footnote (7). “Caution: HMI” added to Engineering Tests, Modulation Equality, and Phasing. Added “One XMTR Only” requirement to Engineering tests. “CBP One XMTR Only” added to Clearance Checklist requirement. Changed Footnote (5), final ILS-3 requirement after width or angle inspection. Changed Main SBO Dephase Commissioning requirement to Maintenance Request.

(e) Paragraph 15.12h(5), Capture Effect Glide Slope. Deleted CBP requirement on standby transmitter. “Caution: HMI” added to Engineering Tests, Modulation Equality, and Phasing. “One XMTR Only” requirement added to Engineering Tests. “CBP One XMTR Only” added to Clearance Checklist requirement. Deleted Upper Antenna Attenuate CBP requirement IAW Notice N8200.74, Interim Changes to Flight Inspection Requirements.

(f) Paragraph 15.12.h(6), Waveguide Glide Slope. Deleted CBP requirement on standby transmitter. Added Footnote (6). “Caution: HMI” added to Engineering Tests and Modulation Equality. “One XMTR Only” added to Engineering Tests, “CBP One XMTR Only” added to Clearance Checklist requirement.

(g) Paragraph 15.12h(7), Endfire Glide Slope. Deleted CBP requirement on standby transmitter. Added Footnote (10). “Caution: HMI” added to Modulation Equality. “CBP One XMTR Only” added to Clearance Checklist requirement. Changed Footnote (6) final ILS-3 requirement after width or angle inspection.

(3) Paragraph 15.20, Detailed Procedures – Localizers. Added HMI instructions to turn off the localizer if the glide slope is transmitting HMI, and vice-versa, in each affected paragraph. Added Modulation Equality procedures during HMI conditions.

(a) Paragraph 15.20b . Changed ILS-1 modulation requirement for “New Type Antenna” changes in NOTE. Changed ILS-1 modulation requirement for standby transmitters.

(b) Paragraph 15. 20d. Changed “RF alarm” to “RF Power Monitor Reference setting”.

Par 1.13 Page 1-5

8200.1C 10/01/05

(c) Paragraph 15.20f. Changed localizer course width distances to match clearance distances. Deleted the requirement for modulation to be in tolerance for course width measurements. Re-defined LCA to coincide with ICAO Annex 10 and Document 8071, International Civil Aviation Organization (ICAO) Manual on Testing of Radio, as pertains to localizer. Added a provision to check course width to a distance of 14 nm on periodic checks. Deleted the requirement to document the data sheet if a higher altitude than LCA is flown, based on width comparability. Deleted Clearance plotting requirements.

(d) Paragraph 15.20g. Moved requirement to establish a modulation balance reference for “Point-In-Space” LDA(s). References DGPS truth system in lieu of an “S/U” alignment for “Point-In-Space” LDA(s). Added localizer structure rollout guidance.

(e) Paragraph 15.20g(2). Added localizer rollout procedures IAW N8200.77, ILS Supporting Lower than Category I Minima.

(f) Paragraph 15.20i. Deleted localizer monitor requirements for lowering LCA. Added reference to localizer alignment monitor requirements only per region request. Deleted the localizer RF monitor reference for lowering LCA.

(g) Paragraph 15.20j. Clarified localizer RF monitor reference when terrain is a factor. Clarified the LCA requirement for localizer RF monitor reference check. Deleted reference to “Requested ESV(s)” pertaining to localizer RF monitor reference checks.

(h) Paragraph 15.20k. Redefined LCA to coincide with ICAO Annex 10 and Document 8071, as pertains to localizer.

(i) Paragraph 15.20m. Added instructions for Fixes, Transitions, SID(s), and STAR (s) when the procedure altitude is below LCA.

(j) Paragraph 15.20o. Deleted the reference to checking Ident and Voice at LCA.

(4) Paragraph 15.30, Glide Slope Flight Inspection Procedures.

(a) Paragraph 15.30d. Added reference to flying the procedural ground track during glide slope phasing. Loosened the requirement for a 1 CBP during glide sope PV. Changed glide slope SBO dephase 30 PV checks to maintenance request in Paragraph 15.30d(3)(a). Added reference to Clearance XMTR status during Glide Slope Phasing Procedures 1 and 2 in Paragraph 15.30d(3)(b)1 and 2.

(b) Paragraph 15.30f. Deleted reference to “GSI corrected to true altitude” on altitude requirement for G/S ILS-2 runs.

(c) Paragraph 15.30n. Restructured “RF Power Monitor Reference” paragraph.

Page 1-6 Par 1.13

10/01/05 8200.1C

(5) Paragraph 15.51, Analysis. Expanded on the Reversal/ Rate-of-Change criteria for standardization purposes. Expanded Order 6750.49, ILS Handbook, requirements into this order. Added Figures 15-8A – F, ILS Reference Requirements checklists.

(6) Paragraph 15.60, Tolerances. Added “Initial” tolerance alignment requirements.

k. Chapter 16, Microwave Landing System (MLS)(Formerly Section 220). Integrated the use of DGPS.

(1) Paragraph 16.20, MLS. Added “DA 200 ft or less” requirement to evaluate an approach below 100 ft DA in Paragraph 16.20b(3)(d). Added to select the MGP angle on AFIS, fly (MGP X 0.75) – 02.5 angle to show full-scale deflection (FSD) in Paragraph 16.20b(4)(c). Changed CBP from fixed angle to FSD. AZ reference point changed to ARD only if DA is less than 200 ft in Paragraph 16.20b(3)(c)3.

(2) Paragraph 16.31, Mobile MLS. Changed Footnote (2) and added Footnote (6)in Checklist. Clarified CEU Change Checklist. Deleted requirement to check AZ/ EL for DEU Change.

(3) Paragraph 16.32. Clarified MCE/ Coverage check in Paragraph 16.32c(2)(a) and (b). Clarified tolerance application for DH above/ below 200 ft. Notice 8200.80, Interim Changes to Flight Inspection Tolerances, added to Paragraph 16.34e(3).

l. Chapter 22, Expanded Service Volume.

(1) Paragraph 22.11b(1). Clarifies NDB crossing radial for  5.

(2) Paragraph 22.12. Incorporates N 8200.72, Expanded Service Volume Process.

m. Appendix 1 (Formerly Section 301). Definition for ILS – Lowest Coverage Altitude clarified on Page A1-12.

n. Appendix 2, (Formerly Section 302).

(1) Paragraph A2.15c. Added parentheses to dual frequency localizer power ratio formula for clarification.

(2) Paragraph A2.16. Added glide slope reference to FAA Order 8240.36 for the purpose of obtaining formula to calculate “Point C”.

Par 1.13 Page 1-7

8200.1C 10/01/05

1.15 BACKGROUND

a. U.S. Policy. International Group on International Aviation (IGIA) 777/4.6G specifies that the FAA will provide flight inspection of the common air navigation system, U.S. military aids worldwide, reimbursable services to other countries, and encourage other countries to establish their own flight inspection capability.

The VFR Flight Inspection Program (VFR FIP) is a support activity of the FAA/ Aviation System Standards (AVN)/ National Aeronautical Charting Office (NACO). In keeping with the statutory responsibilities of the Federal Aviation Act of 1958, NACO is responsible for maintaining the standards of accuracy, completeness, and currency of all air cartographic materials that will meet the minimum standards approved by the FAA and/or the Inter-Agency Air Cartographic Committee’s U.S. Government Chart Specifications.

To supplement office review and ensure the accu racy, completeness, and overall adequacy of these charts, the FAA conducts a system atic program of chart verification by visual flight inspection.

b. Program Objectives. The following objectives re flect FAA philosophy. Current and future planning should be aligned to these objectives.

(1) Adequate site survey and analysis of ground and inflight data.

(2) Correlated ground and flight measurements at the time of facility commissionings.

(3) System reliability to meet justified user needs.

(4) Maximum reliance on ground measurements supported by inflight measurements of those facility parameters which cannot satisfactorily be measured by other means.

(5) Through continued inflight surveillance of the National Airspace System (NAS), determine system adequacy, isolate discrepancies, and provide feedback for system improvement.

(6) To review, verify, and edit topographic, cultural, and obstruction data (roads, railroads, antennas, towers, power lines, rivers, urban areas, etc.) depicted on FAA VFR Aeronautical Charts for accuracy and navigational usefulness.

c. The Interface with Agency Rules. Instrument flight procedures and ATC services require periodic flight surveillance of the air navigation system and dictate strict enforcement of the performance standards adopted for each aid.

d. Flight inspection programs were unified under the FAA by Executive Order 11047, August 28, 1962, subject to the provisions of Executive Order 11161, July 7, 1964. The programs are based on joint DOD/FAA standards, procedures, techniques, and criteria.

Page 1-8 Par 1.14

10/01/05 8200.1C

e. The design standards for air navigation services are documented in Annex 10 to the Convention on International Civil Aviation Organization (ICAO) and in various FAA standards and directives.

f. This order implements the applicable provisions of the North Atlantic Treaty Organization (NATO) Standardization Agreement (STANAG) 3374 AS.

g. Quality Assurance. Flight inspection is the quality assurance program which verifies that the performance of air navigation services and associated instrument flight procedures conform to prescribed standards throughout their published service volume.

1.16 DEFINITIONS. This manual contains policy statements and guidance material. Directive verbs are used.

a. Use MUST when an action is mandatory.

b. Use WILL when it is understood the action will be taken.

c. Use SHOULD when an action is desirable but not mandatory.

d. Use MAY when an action is permissible.

1.17 UNIT OF MEASUREMENT. Unless otherwise stated, the following references are used throughout this manual:

Term(s) Referenced to Mile Nautical Miles Airspeeds and Ground Speeds Knots Bearings, Headings,Azimuths, Radials Direction Magnetic North Information and Instructions RNAV Tracks True North Altitudes Absolute True

1.18 IDENTIFYING CHANGES IN THE TEXT OF THIS MANUAL. A vertical bar is used to highlight substantive changes in the text. The bar will be inserted in the left margin of each column to identify the changes. This paragraph is used as a typical example. Vertical bars are not used in complete rewrites of the Basic Order.

1.19 AUTHORITY TO CHANGE THIS ORDER. The Administrator, in coordination with the DOD, reserves the authority to approve changes which establish policy, delegate authority, or assign responsibility. The Director of Aviation System Standards may issue changes as necessary to implement policy and standardize procedures and techniques for the flight inspection of air navigation services to ensure accomplishment of the U.S. Flight Inspection Program.

Par 1.14 Page 1-9 (and 10)

This Page Intentionally Left Blank.

Chapter 2 - FI Auth

10/01/05 8200.1C

CHAPTER 2. FLIGHT INSPECTION CREW AUTHORITY AND

RESPONSIBILITIES

2.10. AUTHORITY. The flight inspection crew is authorized to:

a. Perform flight inspections of air navigation systems to determine that such systems meet applicable tolerances contained in this manual, and that the facility will support the associated instrument flight procedures.

b. Perform surveillance of aeronautical services.

c. Issue NOTAMs subject to the limitations contained in Chapter 5, Section 1.

d. Certify the signal-in-space of a facility based on the result of the flight inspection.

e. Report hazards encountered during a flight inspection of any type.

f. Take appropriate procedural actions.

g. Review, Verify, and Edit topographic, cultural, and obstruction data depicted on FAA VFR Aeronautical Charts for accuracy and navigational usefulness.

2.11 RESPONSIBILITY. The flight inspection crew is responsible for:

a. Conducting flight inspections in accordance with the procedures established by this manual.

b. Determining the adequacy of the system to meet its required functions.

c. Analyzing and evaluating the flight inspection data to enable a status classification to be assigned.

d. Certifying the signal-in-space of a NAVAID in accordance with the tolerances prescribed in this manual.

e. Coordinating with engineering, maintenance, and/or Air Traffic Operations personnel.

f. Reporting the flight inspection results and status of the system to the appropriate authority.

g. Providing the technical details for NOTAMs based on the flight inspection data.

h. Making recommendations to military installation commanders regarding NOTAMs for military services.

i. Verifying the accuracy of NOTAMs and published information.

j. Flight inspecting instrument flight procedures prior to their publication.

Par 2.10 Page 2-1

8200.1C 10/01/05

k. Optimizing facility performance during flight inspections requiring adjustments.

l. Determining that RNAV procedural leg types meet the intent of the instrument procedure.

m. Conducting flight inspection of non-public procedures IAW this manual and proponent’s approved criteria. Documenting findings for Flight Standards Service (AFS) use in approving or denying the procedure.

Page 2-2 Par 2.11

10/01/05 8200.1C

CHAPTER 3. SPECIAL REQUIREMENTS

3.10 INTRODUCTION. This chapter describes the concept for the special requirements of the aircraft, flight inspection crewmembers, and airborne and ground support equipment used for flight inspection.

Chapter 3 - Spec Rqmts

3.11 AIRCRAFT. Flight inspection organizations (Technical Operations Aviation System Standards (AVN), regions, and the U.S. Military) must identify specific requirements based on their operational needs. Appropriately equipped aircraft and helicopters, from service proponent or other sources, may be used when required to complete flight inspection requirements. The general characteristics of a flight inspection aircraft should be as follows:

a. Equipped for night and instrument flight.

b. Sufficient capacity for a flight inspection crew, observers, ground maintenance and/or installation personnel, and required electronic equipment with spares.

c. Sufficient range and endurance for a normal mission without reservicing.

d. Aerodynamically stable throughout the speed range.

e. Low noise and vibration level.

f. Adequate and stable electrical system capable of operating required electronic and recording equipment and other aircraft equipment.

g. Wide speed and altitude range to allow the conduct of flight inspections under normal conditions as encountered by the users.

h. Appropriate for modifications for flight inspection of new and improved navigation services.

3.12 FLIGHT INSPECTION CREW-MEMBERS. Flight inspection organizations certifying air navigation services must develop a program to formally certify flight inspection personnel. The objectives of this program are to:

a. Grant authority to the flight inspection crewmember who carries out the administration's responsibility of ensuring the satisfactory operation of air navigation services, instrument flight procedures, and VFR Aeronautical Chart verification.

b. Provide a uniform method for examining employee competence.

c. Issue credentials which authenticate certification authority for the crewmember.

Par 3.10 Page 3-1

8200.1C 10/01/05

3.13 AIRBORNE AND GROUND SUPPORT EQUIPMENT. Aircraft and ground support flight inspection equipment must be calibrated to a standard traceable to the National Institute of Standard and Technology.

a. An Automated Flight Inspection System (AFIS), when applicable, is the primary method for conducting flight inspections.

b. Other AVN Approved Systems (Portable/Utility Class) and Methods (Theodolite, RTT, or Manual) may be used unless prohibited by other guidance for flight inspection. These systems/ methods must not be used solely to bypass the need for facility data of sufficient accuracy to support AFIS. Portable/Utility class equipment, installed in aircraft for the purpose of conducting flight inspections, must be installed in accordance with AVN approved procedures.

Page 3-2 Par 3.13

Chapter 4 - FI Types

10/01/05 8200.1C

CHAPTER 4. FLIGHT INSPECTION TYPES, PRIORITIES, INTERVALS,

PROCEDURES

TABLE OF CONTENTS

SECTION 1. TYPES AND PRIORITIES OF FLIGHT INSPECTIONS

Paragraphs Title Pages

4.10 INTRODUCTION … 4-1

4.11 SITE EVALUATION … 4-1

4.12 COMMISSIONING … 4-1

Commissioning of Facilities on Incomplete Runways … 4-1

4.13 PERIODIC … 4-1

4.14 SPECIAL FLIGHT INSPECTIONS … 4-1 a. USAF ATCALS Evaluation Requirements … 4-1 b. USAF Deployable (Mobile) ATCALS (DATCALS) … 4-1 c. Unapproved Facilities … 4-2 d. Facility Removal and Replacement … 4-2 e. New or Modified Equipment Testing … 4-2 f. Radio Frequency Interference (RFI) … 4-2 g. After Accident … 4-2 h. Reconfiguration … 4-3 i. Inspections of Shipboard TACAN(s) … 4-3

4.15 SURVEILLANCE … 4-3 Surveillance of Aeronautical Services … 4-4

4.16 PRIORITIES OF FLIGHT INSPECTIONS … 4-5

Page 4-i

8200.1C 10/01/05

TABLE OF CONTENTS

Paragraphs Title Pages

SECTION 2. FREQUENCY OF PERIODIC FLIGHT INSPECTIONS

4.20 INTRODUCTION … 4-6

4.21 EXTENSION OF SERVICES OVERDUE PERIODIC INSPECTION … 4-7

4.22 NAVAIDS TEMPORARILY OUT-OF-SERVICE … 4-7

4.23 RHO-THETA RECEIVER CHECKPOINTS … 4-8

4.24 PERIODIC FLIGHT INSPECTION INTERVALS … 4-9

4.25 ILS MONITOR (OR REFERENCE) INTERVALS … 4-9

SECTION 3. GENERAL FLIGHT INSPECTION PROCEDURES

4.30 INTRODUCTION … 4-10

4.31 REQUEST FOR FLIGHT INSPECTION … 4-10

4.32 PREFLIGHT INSPECTION PREPARATION … 4-11

4.33 FLIGHT INSPECTION … 4-12

4.34 ANALYSIS AND EVALUATION … 4-14

4.35 POST FLIGHT INSPECTION ACTIONS … 4-14

Page 4-ii

10/01/05 8200.1C

CHAPTER 4. FLIGHT INSPECTION TYPES, PRIORITIES, INTERVALS,

PROCEDURES

SECTION 1. TYPES AND PRIORITIES OF FLIGHT INSPECTIONS

4.10 INTRODUCTION. Official flight inspections are of five basic types: site evaluation, commissioning, periodic, special, and surveillance.

4.11 SITE EVALUATION: A flight inspection to determine the suitability of a proposed site for the permanent installation of a facility. It may include checks normally made during a commissioning inspection and any additional tests which may be required.

4.12 COMMISSIONING: A comprehensive flight inspection designed to obtain complete information as to system performance and to establish that the system will support its operational requirements.

Commissioning of Facilities or Services on Incomplete Runways. Occasionally, a commissioning inspection is performed prior to the completion of runway construction activities, including but not limited to, painting and lighting. When this occurs, a Special Flight Inspection should be performed after completion of the runway work and before the facility is placed into service. The flight inspector performing the commissioning check must request the Special inspection, specifying the items needing inspection. If, in the flight inspector's judgment, the remaining runway work is negligible and no Special inspection is required before facility use, the condition must be documented on the Daily Flight Log.

4.13 PERIODIC: A regularly scheduled flight inspection to determine that the system meets standards and supports the operational requirements.

4.14 SPECIAL FLIGHT INSPECTIONS are inspections performed outside the normal periodic interval. They may be used to define/evaluate performance characteristics of systems, subsystems, or individual facilities. Facilities maintenance personnel must be responsible for coordinating with flight inspection which checks are to be accomplished, based on their requirements and type of maintenance performed on the equipment. Special inspections are also performed when radio frequency interference (RFI) degrades intended facility services.

a. USAF Air Traffic Control and Landing System (ATCALS) evaluation requirements. ATCALS evaluation inspections require a minimum of a periodic-with-monitors type profile for ILS and periodic-type profile for all other facilities.

b. USAF Deployable (Mobile) ATCALS (DATCALS). Flight inspections of DATCALS deployed to support an exercise or operational readiness inspection (ORI), and not intended for actual use, are considered special inspections. These facilities will be inspected to the extent necessary to assess the mobile unit’s deployment capability. The procedures and checklists contained in Chapter 24 will normally be accomplished. The ORI/exercise team chief will be responsible, after consulting with the flight inspector, for assessing the facility and determining if the unit could operate during an actual deployment. The facility classification will be “unusable” due to the limited nature of the check.

Par 4.10 Page 4-1

8200.1C 10/01/05

c. Unapproved Facilities. Inspections of facilities not approved for use (equipment under test, facilities without monitors, etc.) will be special inspections. Since these facilities cannot be commissioned for IFR use, the status will be unusable. Items inspected will be largely dependent on the customer’s request.

d. Facility Removal and Replacement. When the equipment replaced is the same type and configuration as the former and located on the same physical site, including antenna location, a special check is required. Required items for an antenna change in each chapter must be accomplished as a minimum. Additional requirements of such a check will be jointly determined by the flight inspector and facilities maintenance.

e. New or Modified Equipment Testing. All testing of new or modified types of equipment that require flight inspection support must be coordinated with Flight Inspection Policy. Flight Inspection Policy will determine if personnel from that office will participate in the testing to both ensure the adequacy of the testing and scope of any flight inspection procedural changes required to support the equipment. This encompasses Operational Testing and Evaluation (OT&E), First Article Testing, Developmental Test and Evaluation (DT&E), and similar formal testing; it does not include normal flight inspection of subsequent installations. If any doubt exists about the need for coordination, contact Flight Inspection Policy.

f. Radio Frequency Interference (RFI). All inspections to confirm or locate natural or man-made interference to Communication, Navigation, or Surveillance (CNS) systems using flight inspection aircraft must be performed by qualified flight inspection personnel; spectrum management specialists may assist in the mission as necessary. A flight inspection report on the affected system must be completed.

g. After Accident. This inspection is performed at the request of the accident coordinator/investigator to verify that system performance is satisfactory and continues to support instrument flight procedure(s).

(1) Response. This inspection has a priority of 1a and should be accomplished as soon as possible.

(2) Preflight Requirements. The flight inspector must obtain the following information:

(a) Equipment configuration at the time of the accident, i.e., the receiver(s), transmitter(s), or radar channel(s) in operation.

(b) Instrument flight procedure(s) used.

(c) Any additional information that may aid in the inspection analysis.

Page 4-2 Par 4.14

(3) Inspection Procedure(s)

(a) Coordinate with maintenance to configure the system as indicated in Paragraph g(2)(a).

(b) Complete periodic checklist requirements. Only the equipment and instrument flight procedures used by the accident aircraft need to be checked. A VOR or TACAN alignment orbit is not required. Do not make any facility adjustments during the after accident inspection. Any adjustments must require a separate special inspection.

(c) If a system or procedure has no periodic inspection requirements, evaluate performance in the area in which the accident occurred.

(d) Complete any additional items requested by maintenance, air traffic control personnel, the accident coordinator, or the commander at a military facility.

(e) Where an accident involves contact with the terrain or a manmade obstruction, confirm the procedural controlling obstruction by map study or flight evaluation.

(4) Dissemination of After Accident Information. All flight inspection findings or other pertinent accident investigation information must be restricted to the cognizant accident coordinator/ investigator, maintenance, and air traffic personnel. Results of the flight inspection must be given to the FAA Inspector-in-Charge (IIC) as soon as possible. A flight inspection report must be filed in accordance with current directives.

h. Reconfiguration. A special flight inspection requested by maintenance when modifications or the relocation of a facility affect the radiation pattern of the facility. Antenna changes to different type antennas must be classified as a reconfiguration inspection. All commissioning checks should be performed following a facility reconfiguration, except those that are not required as determined jointly by flight inspection and facilities maintenance personnel. Commissioning tolerances must be applied.

i. Inspections of Shipboard TACAN(s) are considered com plete at the term ination of the inspection. Any subsequent inspection must be a new "special" inspection.

4.15 Surveillance. An ongoing observation of individual components of commissioned systems, procedures, or services. This inspection encompasses spot checks of individual components observed during normal flight operations. No reporting is required unless a discrepancy is found. An out-of-tolerance or unsatisfactory condition found on a surveillance inspection requires a Daily Flight Log entry, report, and, if necessary, NOTAM action.

Par 4.14 Page 4-3

Surveillance of Aeronautical Services. During the course of routine flight operations, flight inspection personnel must be alert for items which are unusual, substandard, or possibly hazardous.

a. Inspections. Inspections may include, but are not limited to, the following:

(1) Condition of runways, taxiways, and ramp areas.

(2) Runway, taxiway paint markings, and position signs missing or deteriorated to the extent that visual guidance is obscured or missing.

(3) Conditions which may lead to runway incursion by aircraft, vehicles, or pedestrians.

(4) Construction activity at airports which is a hazardous condition or might affect NAVAID performance.

(5) New obstructions in the instrument approach area which might become the controlling obstruction or constitute a hazardous condition.

(6) Brush or tree growth obstructing the view of approach lights.

(7) Obscured or broken runway or obstruction lights.

(8) Other hazardous situations (e.g., bird hazards).

(9) Air traffic services (e.g., clearances, flight plans, communications).

(10) Other services (e.g., weather bureau services or other airport support services).

b. Reports. See FAA Order 8240.36, Flight Inspection Report Processing System (latest edition).

Page 4-4 Par 4.15

4.16 PRIORITIES OF FLIGHT INSPECTIONS. The priorities listed below must be used to determine which mission will be supported first when two or more requirements are competing for limited flight inspection resources. All inspections should be scheduled to make the most effective use of aircraft and aircrew. Schedulers should consider weather; maintenance team availability; other facilities enroute; impact on both the airport and NAS; and Technical Operations Facilities, Service, and Equipment Profile (FSEP) Response Codes when scheduling missions.

Priority

1a

Type of Service

Accident Investigation, RFI impacting NAS services, any facility which has exceeded its inspection interval, inspection of facilities in support of military contingencies, or other nationally directed military deployments.

1b Restoration of a commissioned facility after an unscheduled outage, restoration of CAT II/ III ILS approach minimums, or inspection of NAVAID(s) in support of military operational readiness and JCS directed exercises.

1c Flight inspection of reported malfunctions.

1d Restoration of a commissioned facility following a scheduled shutdown or inspections supporting DOD NAVAID evaluations (USAF TRACALS).

2a Site evaluation.

2b Commissioning inspection of a new facility or new instrument flight procedures.

3a Periodic inspections.

3b Restoration of standby equipment (except CAT II/ III ILS, see priority lb).

3c Navigational Aids Signal Evaluator (NASE) evaluations

3d Restoration of VFR training facilities following a scheduled or unscheduled outage.

Par 4.16 Page 4-5

SECTION 2. FREQUENCY OF PERIODIC FLIGHT INSPECTIONS

4.20 Introduction. This section prescribes the minimum frequency of periodic flight inspections. More frequent inspections may be made when deemed necessary or as requested by the owner or organization responsible for the operation of the facility.

a. Intervals. Table 4-1 specifies the intervals between scheduled periodic flight inspections. Due dates for periodic inspections are based on this schedule. Military, foreign, and MOA systems, facilities, and procedures may have unique requirements and non-standard inspection intervals. All records and reports will reflect the actual date(s) of the inspection and will specifically denote the date of completion. The next periodic inspection will be predicated on the actual date of completion.

(1) Due date window for facilities with a 90-day periodicity is from 15 days before to 15 days after the due date.

(2) Due date window for all other facilities, systems, and procedures is from 60 days before to 60 days after the due date.

(3) Due date window for VFR Aeronautical Charts is from 120 days before to 120 days after the due date.

NOTE: The VFR Flight Inspection Pr ogram will im plement VFR Chart periodicity over a period of years.

For the contiguous United States, the chart periodicity is being implemented over the next several years. The periodic due date for each individual Sectional Aeronautical Chart and its associated Terminal Area and Flyway Chart is being established as the chart is inspected. Inspection and periodicity for the Aeronautical Charts outside the contiguous United States will be implemented in the future. Helicopter and Special VFR Charts have no periodicity and are updated as determined by NACO.

b. Scheduling

(1) NAVAID(s) such as VORTAC, VOR/ DME, ILS, MLS, etc., must be flight inspected as a service with the same due date and inspection interval for all component facilities.

(2) The inspection priority must be raised to 1a when the system, facility, or procedure has exceeded the end of the due date window.

(3) Periodic inspections are considered complete when all scheduled checks are accomplished except as noted below. When flight inspection of all Standard Instrument Approach Procedures (SIAP(s)) cannot be completed within the periodic window and extension, the periodic inspection will be documented as complete, as directed by the Flight Inspection Central Operations (FICO) Manager.

Page 4-6 Par 4.20

10/01/05 8200.1C

Special inspections must be established to ensure the remaining SIAP(s) are completed. In the event the SIAP(s) are not checked by the end of the periodic window/ extension, the FICO must initiate NOTAM action to remove them from service. The SIAP(s) must be restored by a special flight inspection.

(4) Progressive Inspections. The requirements for periodic inspections are specified in a checklist in each chapter of this order. Partial or progressive inspections may be conducted, provided all of the individual periodic checklist items are satisfied within the due date window.

4.21 Extension of Services Overdue Periodic Inspection. When the inspection of a commissioned NAVAID or SIAP is not completed within the due date window, the window may be extended. The flight inspection priority of a NAVAID or SIAP in an extension is the same as an overdue NAVAID or procedure.

a. The periodic flight inspection window for a ground NAVAID may be extended an additional seven (7) calendar days if the FICO and regional facility maintenance engineering agree that no conditions exist which could adversely affect the safety of flight.

b. The periodic flight inspection window for all SIAP(s) may be extended an additional thirty (30) calendar days providing:

(1) A review of the SIAP is accomplished by a Flight Inspector and;

(2) Flight Inspection Central Operations (FICO), by coordination with regional or local airport personnel can determine that no known environmental (i.e., construction or natural growth) changes have occurred which could adversely affect the procedure and;

(3) The National Flight Procedures Office agrees that an extension of the window will not adversely affect the safety of flight.

4.22 NAVAIDS Temporarily Out-of-Service

a. Use the priority listed in Section 1 of this chapter when a restoration inspection is required. The next periodic inspection must be predicated on the completion date of an inspection which satisfies all periodic checklist requirements.

b. When a portion of a NAVAID is restored to service, the periodic due dates must be established in accordance with Paragraphs 4.20a and 4.23.

c. Standby Equipment or Associated NAVAID. When flight inspection of standby equipment or an associated NAVAID is required but cannot be accomplished, the periodic inspection will be considered complete if the standby equipment or associated NAVAID is out-ofservice (awaiting parts, etc.), or removed from service (due to an uncorrectable discrepancy, etc.)

Par 4.20 Page 4-7

Continue reading ↓ 120 of 1100 passages shown