Radar Vectors
FAA Order Cancelled Issued Dec 7, 2007 AFS-420 343 pages Copy saved Nov 18, 2026

Order 8260.54A The United States Standard for Area Navigation

This document is cancelled. Cancelled by 8260.58. Check the official source before relying on it.

Official source ↗ Open PDF

Order 8260.54A

Distribution: A-W(AS/ND/AT/AF/FS)-3; A-X(FS/AF/AT/AS)-3; AJW-32 (200 Cys); AMA-200 (12 Cys); ZVS-827; Special Military and Public Addresses

Initiated By: AFS-420

The Global Positioning System (GPS) provides greater flexibility in the design of instrument approach procedures. FAA Order 8260.38, Civil Utilization of Global Positioning System (GPS), introduced GPS approach procedures into the National Airspace System (NAS) in 1993. Order 8260.48, Area Navigation (RNAV) Approach Construction Criteria (1999) and Order 8260.50, The United States Standard for LPV Approach Procedure Construction Criteria (2002), introduced Wide Area Augmentation System (WAAS) approach construction criteria. As the NAS evolves from one based on conventional navigation aids to an RNAV system, the capability of the GPS based systems is being more clearly quantified. This document consolidates and refines RNAV criteria, incorporating GPS, WAAS, and Local Area Augmentation System (LAAS) navigation systems. Original Signed By Carol Giles James J. Ballough Director Flight Standards Service

National Policy

Effective Date:

12/07/07

SUBJ: The United States Standard for Area Navigation (RNAV)

ORDER

8260.54A

RECORD OF CHANGES

8260.54A

CHANGE SUPPLEMENTS CHANGE SUPPLEMENTS

TO OPTIONAL USE TO OPTIONAL USE BASIC BASIC

FAA Form 1320-5 SUPERSEDES PREVIOUS EDITION

i

TABLE OF CONTENTS Page Chapter 1.

Order 8260.54A › Table of Contents

General 1.0 Purpose of this Order------------------------------------------------------------------1-1 1.1 Audience --------------------------------------------------------------------------------1-1 1.2 Where Can I find this Order----------------------------------------------------------1-1 1.3 Cancellation-----------------------------------------------------------------------------1-1 1.4 Explanation of Changes---------------------------------------------------------------1-1 1.4.1 Chapter 1--------------------------------------------------------------------------------1-2 1.4.2 Chapter 2--------------------------------------------------------------------------------1-2 1.4.3 Chapter 3--------------------------------------------------------------------------------1-4 1.4.4 Chapter 4--------------------------------------------------------------------------------1-4 1.4.5 Chapter 5--------------------------------------------------------------------------------1-4 1.4.6 Chapter 6--------------------------------------------------------------------------------1-4 1.4.7 Appendix

1------------------------------------------------------------------------------1-4 1.4.7 Appendix 2------------------------------------------------------------------------------1-4 1.5 Background-----------------------------------------------------------------------------1-4 1.6 Effective Date --------------------------------------------------------------------------1-5 1.7 Definitions ------------------------------------------------------------------------------1-5 1.7.1 Along-Track Distance (ATD)--------------------------------------------------------1-5 1.7.2 Along-Track (ATRK) Tolerance (ATT)--------------------------------------------1-5 1.7.3 Barometric Altitude--------------------------------------------------------------------1-5 1.7.4 Cross-Track (XTT) Tolerance -------------------------------------------------------1-5 1.7.5 Decision Altitude (DA) ---------------------------------------------------------------1-6 1.7.6 Departure End of Runway (DER)---------------------------------------------------1-6 1.7.7 Distance of Turn Application (DTA)

-----------------------------------------------1-6 1.7.8 Fictitious Threshold Point (FTP) ----------------------------------------------------1-6 1.7.9 Fix Displacement Tolerance (FDT)-------------------------------------------------1-7 1.7.10 Flight Path Alignment Point (FPAP)------------------------------------------------1-7 1.7.11 Geoid Height (GH) --------------------------------------------------------------------1-7 1.7.12 Glidepath Angle (GPA)---------------------------------------------------------------1-7 1.7.13 Glidepath Qualification Surface (GQS) --------------------------------------------1-8 1.7.14 Height Above Ellipsoid (HAE) ------------------------------------------------------1-8 1.7.15 Height Above Threshold (HATh) ---------------------------------------------------1-9 1.7.16 Inner-Approach Obstacle Free Zone (OFZ)----------------------------------------1-9 1.7.17 Inner-Transitional OFZ ---------------------------------------------------------------1-9 1.7.18 Landing Threshold Point (LTP) -----------------------------------------------------1-9 1.7.19 Lateral

Navigation (LNAV)----------------------------------------------------------1-10 1.7.20 Lateral Navigation/Vertical Navigation (LNAV/VNAV) -----------------------1-10 1.7.21 Localizer Performance (LP)----------------------------------------------------------1-10 1.7.22 Localizer Performance with Vertical Guidance (LPV)---------------------------1-10 1.7.23 Obstacle Evaluation Area (OEA)----------------------------------------------------1-10 1.7.24 Obstacle Clearance Surface (OCS)--------------------------------------------------1-10

12//07/07 8260.54A

ii

TABLE OF CONTENTS (Continued) Page Chapter 1. General (Continued) 1.7.25 Obstacle Positions (OBSX,Y,Z)--------------------------------------------------------1-11 1.7.26 Precise Final Approach Fix (PFAF)-------------------------------------------------1-11 1.7.27 Reference Datum Point (RDP)-------------------------------------------------------1-11 1.7.28 Runway Threshold (RWT)-----------------------------------------------------------1-12 1.7.29 Start of Climb (SOC)------------------------------------------------------------------1-12 1.7.30 Threshold Crossing Height (TCH) --------------------------------------------------1-12 1.7.31 Visual Glide Slope Indicator (VGSI) -----------------------------------------------1-12 1.7.32 Wide Area Augmentation System (WAAS)---------------------------------------1-12 1.8 Information Update--------------------------------------------------------------------1-12 Chapter 2. General Criteria Section 1.

Basic Criteria Information 2.0 General ----------------------------------------------------------------------------------2-1 2.1 Data Resolution ------------------------------------------------------------------------2-1 2.1.1 Documentation Accuracy-------------------------------------------------------------2-2 2.1.2 Mathematics Convention -------------------------------------------------------------2-2 2.1.3 Geospatial Standards ------------------------------------------------------------------2-5 2.1.4 Evaluation of Actual and Assumed Obstacles (AAO)----------------------------2-6 2.1.5 ATT Values-----------------------------------------------------------------------------2-6 2.2 Procedure Identification---------------------------------------------------------------2-7 2.3 Segment Width (General)-------------------------------------------------------------2-7 2.3.1 Width Changes at 30 NM from ARP (non-RF) -----------------------------------2-9 2.3.2 Width Changes at 30 NM from ARP (RF)-----------------------------------------2-9 2.4 Calculating the Turn Radius

(R)-----------------------------------------------------2-11 2.5 Turn Construction----------------------------------------------------------------------2-15 2.5.1 Turns at Fly-Over Fixes---------------------------------------------------------------2-15 2.5.2 Fly-By Turn-----------------------------------------------------------------------------2-20 2.5.3 Radius-to-Fix (RF) Turn--------------------------------------------------------------2-22 2.6 Descent Gradient-----------------------------------------------------------------------2-24 2.6.1 Calculating Descent Gradient (DG)-------------------------------------------------2-25 2.7 Feeder Segment ------------------------------------------------------------------------2-26 2.7.1 Length -----------------------------------------------------------------------------------2-26 2.7.2 Width ------------------------------------------------------------------------------------2-26 2.7.3 Obstacle Clearance --------------------------------------------------------------------2-28 2.7.4 Descent

Gradient-----------------------------------------------------------------------2-29 Section 2. Terminal Segments 2.8 Initial Segment -------------------------------------------------------------------------2-30 2.8.1 Course Reversal------------------------------------------------------------------------2-30 2.8.2 Alignment-------------------------------------------------------------------------------2-31

iii

TABLE OF CONTENTS (Continued) Page Chapter 2. General Criteria (Continued) 2.8.3 Area - Length---------------------------------------------------------------------------2-31 2.8.4 Area - Width----------------------------------------------------------------------------2-31 2.8.5 Obstacle Clearance --------------------------------------------------------------------2-31 2.8.6 Holding Pattern Initial Segment -----------------------------------------------------2-32 2.9 Intermediate Segment -----------------------------------------------------------------2-34 2.9.1 Alignment-------------------------------------------------------------------------------2-34 2.9.2 Length -----------------------------------------------------------------------------------2-34 2.9.3 Width ------------------------------------------------------------------------------------2-34 2.9.4 Obstacle Clearance --------------------------------------------------------------------2-41 2.9.5 Minimum IF to LTP Distance--------------------------------------------------------2-42 Section 3.

Basic Vertically Guided Final Segment General Criteria 2.10 Authorized Glidepath Angles (GPAs) ----------------------------------------------2-43 2.11 Threshold Crossing Height (TCH) --------------------------------------------------2-43 2.12 Determining FPAP Coordinates (LPV and LP only) -----------------------------2-44 2.13 Determining PFAF/FAF Coordinates-----------------------------------------------2-46 2.14 Determining Glidepath Altitude at a Fix -------------------------------------------2-49 2.15 Common Fixes -------------------------------------------------------------------------2-50 2.16 Clear Areas and Obstacle Free Zones (OFZ) --------------------------------------2-50 2.17 Glidepath Qualification Surface (GQS) --------------------------------------------2-50 2.17.1 Area--------------------------------------------------------------------------------------2-51 2.18 Precision Obstacle Free Zone (POFZ)----------------------------------------------2-58 Section 4.

Missed Approach General Information 2.19 Missed Approach Conventions ------------------------------------------------------2-60 2.19.1 Charted Missed Approach Altitude -------------------------------------------------2-61 2.19.2 Climb-In-Holding----------------------------------------------------------------------2-61 Chapter 3.

Non-Vertically Guided Procedures (NVGP) 3.0 General ----------------------------------------------------------------------------------3-1 3.1 Alignment-------------------------------------------------------------------------------3-1 3.2 Area - LNAV Final Segment---------------------------------------------------------3-2 3.2.1 Length -----------------------------------------------------------------------------------3-2 3.2.2 Width ------------------------------------------------------------------------------------3-2 3.3 Area - LP Final Segment--------------------------------------------------------------3-3 3.3.1 Length -----------------------------------------------------------------------------------3-4 3.3.2 Width ------------------------------------------------------------------------------------3-4 3.4 Obstacle Clearance --------------------------------------------------------------------3-5 3.4.1 Primary Area ---------------------------------------------------------------------------3-5 3.4.2 Secondary Area

------------------------------------------------------------------------3-5

iv

TABLE OF CONTENTS (Continued) Page Chapter 3. Non-Vertically Guided Procedures (Continued) 3.5 Final Segment Stepdown Fixes (SDF)----------------------------------------------3-5 3.6 Minimum Descent Altitude (MDA)-------------------------------------------------3-8 3.7 Missed Approach Section 1 (MAS-1) ----------------------------------------------3-8 3.7.1 Length -----------------------------------------------------------------------------------3-8 3.7.2 Width. LNAV and LP----------------------------------------------------------------3-9 3.7.3 Obstacle Clearance. LNAV and LP ------------------------------------------------3-10

Chapter 4.

Lateral Navigation with Vertical Navigation (LNAV/VNAV) Final Segment 4.0 General ----------------------------------------------------------------------------------4-1 4.1 Final Approach Course Alignment--------------------------------------------------4-1 4.2 Area--------------------------------------------------------------------------------------4-2 4.2.1 Length -----------------------------------------------------------------------------------4-3 4.2.2 Width ------------------------------------------------------------------------------------4-3 4.3 Obstacle Clearance Surface (OCS)--------------------------------------------------4-3 4.3.1 Low Temperature Limitation --------------------------------------------------------4-5 4.3.2 High Temperature Limitation--------------------------------------------------------4-6 4.3.3 OCS Slope ------------------------------------------------------------------------------4-9 4.3.4 Final Segment Obstacle Evaluation -------------------------------------------------4-9 4.4 Missed Approach Section 1

----------------------------------------------------------4-15 4.4.1 Area--------------------------------------------------------------------------------------4-15 Chapter 5.

LPV Final Approach Segment (FAS) Evaluation 5.0 General ----------------------------------------------------------------------------------5-1 5.1 Final Segment Obstruction Evaluation Area (OEA)------------------------------5-1 5.1.1 OEA Alignment------------------------------------------------------------------------5-2 5.1.2 OCS Slope(s)---------------------------------------------------------------------------5-3 5.1.3 OCS Origin -----------------------------------------------------------------------------5-4 5.2 W OCS ----------------------------------------------------------------------------------5-4 5.2.1 Width ------------------------------------------------------------------------------------5-5 5.2.2 Height------------------------------------------------------------------------------------5-5 5.2.3 W OCS Evaluation --------------------------------------------------------------------5-7 5.3 X OCS-----------------------------------------------------------------------------------5-8 5.3.1 Width

------------------------------------------------------------------------------------5-8 5.3.2 X Surface Obstacle Elevation Adjustment (Q) ------------------------------------5-9 5.4 Y OCS-----------------------------------------------------------------------------------5-9 5.4.1 Width ------------------------------------------------------------------------------------5-10 5.4.2 Y Surface Obstacle Elevation Adjustment (Q) ------------------------------------5-10 5.5 HATh and DA--------------------------------------------------------------------------5-11 5.5.1 DA Calculation (Clear OCS)---------------------------------------------------------5-11

Policy Memo Mar 3 2008

v

TABLE OF CONTENTS (Continued) Page Chapter 5. LPV Final Approach Segment (FAS) Evaluation (Continued) 5.5.2 DA Calculation (OCS Penetration)--------------------------------------------------5-12 5.6 Revising Glidepath Angle (GPA) for OCS Penetrations-------------------------5-13 5.7 Adjusting TCH to Reduce/Eliminate OCS Penetrations -------------------------5-14 5.8 Missed Approach Section 1 (Height Loss and Initial Climb)--------------------5-14 5.8.1 Section 1a -------------------------------------------------------------------------------5-16 5.8.2 Section 1b-------------------------------------------------------------------------------5-17 5.9 Surface Height Evaluation------------------------------------------------------------5-20 5.9.1 Section 1a -------------------------------------------------------------------------------5-20 5.9.2 DA Adjustment for a Penetration of Section 1bSurface--------------------------5-21 5.9.3 End of Section 1 Values --------------------------------------------------------------5-22 Chapter 6.

Missed Approach Section 2 6.0 General ----------------------------------------------------------------------------------6-1 6.1 Straight Missed Approach------------------------------------------------------------6-2 6.2 Turning Missed Approach (First Turn)---------------------------------------------6-2 6.2.1 Turn at an Altitude---------------------------------------------------------------------6-3 6.2.2 Turns at a Fix---------------------------------------------------------------------------6-10 6.2.3 Section 2 Obstacle Evaluations ------------------------------------------------------6-15 6.3 Turning Missed Approach (Second Turn)------------------------------------------6-16 6.3.1 DF/TF Turn (Section Turn, following turn-at-altitude)---------------------------6-16 6.3.2 TF/TF Turn (Second Turn, following turn-at-fix)---------------------------------6-18 6.4 Wind Spiral Cases ---------------------------------------------------------------------6-19 6.4.1 First MA Turn WS Construction ----------------------------------------------------6-21 6.4.2 Second MA Turn WS Construction

(DF/TF FO) ---------------------------------6-24 6.5 Missed Approach Climb Gradient---------------------------------------------------6-26 Appendix 1. Formulas by Chapter, Formatted for an Aid to Programming Formulas, Chapter 1 and 2------------------------------------------------------------A1-1 Formulas, Chapter 3 and 4------------------------------------------------------------A1-2 Formulas, Chapter 5-------------------------------------------------------------------A1-3 Formulas, Chapter 6-------------------------------------------------------------------A1-4 Appendix 2.

Geodetic Formula Standard 1.0 Purpose----------------------------------------------------------------------------------A2-1 2.0 Introduction-----------------------------------------------------------------------------A2-2 2.1 Data Structures -------------------------------------------------------------------------A2-3 2.1.1 Geodetic Locations --------------------------------------------------------------------A2-3 2.1.2 Geodetic Curves------------------------------------------------------------------------A2-4 2.1.3 Fixed Radius Arc ----------------------------------------------------------------------A2-4

vi

TABLE OF CONTENTS (Continued) Page Appendix 2.

Geodetic Formula Standard (Continued) 2.1.4 Locus of Points Relative to a Geodesic---------------------------------------------A2-4 3.0 Basic Calculations ---------------------------------------------------------------------A2-6 3.1 Iterative Approach ---------------------------------------------------------------------A2-6 3.2 Starting Solutions ----------------------------------------------------------------------A2-7 3.2.1 Spherical Direction Intersect ---------------------------------------------------------A2-7 3.2.2 Spherical Distance Intersection ------------------------------------------------------A2-8 3.2.3 Spherical Tangent Point---------------------------------------------------------------A2-9 3.2.4 Two Points and a Bearing Case------------------------------------------------------A2-9 3.2.5 Given Three Points Case--------------------------------------------------------------A2-10 3.3 Tolerances-------------------------------------------------------------------------------A2-10 3.4 Direct and Inverse Algorithms-------------------------------------------------------A2-11

3.4.1 Vincenty’s Direct Formula -----------------------------------------------------------A2-11 3.4.2 Vincenty’s Inverse Formula----------------------------------------------------------A2-12 3.5 Geodesic Oriented at Specified Angle----------------------------------------------A2-13 3.6 Determine if Point Lies on Geodesic------------------------------------------------A2-15 3.7 Determine if Point Lies on Arc ------------------------------------------------------A2-18 3.8 Calculate Length of Fixed Radius Arc----------------------------------------------A2-20 3.9 Find Distance from Defining Geodesic to Locus----------------------------------A2-25 3.10 Project Point on Locus from Point on Defining Geodesic -----------------------A2-26 3.11 Determine if Point Lies on Locus----------------------------------------------------A2-27 3.12 Compute Course of Locus------------------------------------------------------------A2-29 4.0 Intersections ----------------------------------------------------------------------------A2-32 4.1 Intersection of Two

Geodesics-------------------------------------------------------A2-32 4.2 Intersection of Two Arcs--------------------------------------------------------------A2-36 4.3 Intersections of Arc and Geodesic---------------------------------------------------A2-40 4.4 Arc Tangent to Two Geodesics------------------------------------------------------A2-45 4.5 Intersections of Geodesics and Locus-----------------------------------------------A2-50 4.6 Intersections of Arc and Locus-------------------------------------------------------A2-54 4.7 Intersections of Two Loci-------------------------------------------------------------A2-56 4.8 Arc tangent to Two Loci--------------------------------------------------------------A2-59 5.0 Projections ------------------------------------------------------------------------------A2-64 5.1 Project Point to Geodesic -------------------------------------------------------------A2-64 5.2 Project Point to Locus-----------------------------------------------------------------A2-68 5.3 Tangent Projection from Point to

Arc-----------------------------------------------A2-72 5.4 Project Arc to Geodesic---------------------------------------------------------------A2-75 6.0 Converting Geodetic Latitude/Longitude to ECEF Coordinates----------------A2-80 6.1 Signed Azimuth Difference ----------------------------------------------------------A2-80 6.2 Approximate Fixed Radius Arc Length --------------------------------------------A2-80 7.0 Sample Function Test Results--------------------------------------------------------A2-82

Order 8260.54A › Chapter 1. General

Chapter 1. General 1.0 Purpose of This Order. This order specifies criteria for obstacle clearance evaluation of area navigation (RNAV) approach procedures; e.g., Localizer Performance with Vertical Guidance (LPV), Lateral Navigation (LNAV), Lateral Navigation/Vertical Navigation (LNAV/VNAV), and Localizer Performance (LP). These criteria support adding an instrument landing system (ILS) line of minimums to an RNAV (GPS) approach procedure using LPV construction criteria at runways served by instrument landing system. Apply feeder segment criteria (paragraph 2.7) to satisfy RNAV Standard Terminal Arrival Route (STAR) and Tango (T) Air Traffic Service (ATS) route obstacle clearance requirements. Note: These criteria do not support very high frequency (VHF) omnidirectional range/distance measuring equipment (VOR/DME) RNAV, inertial navigation system (INS), or inertial reference unit (IRU) RNAV operations, or DME/DME RNAV final or missed approach operations. 1.1 Audience.

This order is distributed in Washington headquarters to the branch level in the Offices of Airport Safety and Standards and Communications, Navigation, and Surveillance Systems; Air Traffic Organization (Safety, En Route and Oceanic Services, Terminal Services, System Operations Services, and Technical Operations Services), and Flight Standards Services; to the National Flight Procedures Office and the Regulatory Standards Division at the Mike Monroney Aeronautical Center; to branch level in the regional Flight Standards and Airports Divisions; special mailing list ZVS-827, and to Special Military and Public Addressees. 1.2 Where Can I Find This Order? This information is also available on the FAA's Web site at http://fsims.avr.faa.gov/fsims/fsims.nsf. 1.3 Cancellation.

Order 8260.38A, Civil Utilization of Global Positioning System (GPS), dated April 5, 1995; Order 8260.48, Area Navigation (RNAV) Approach Construction Criteria, dated April 8, 1999, and Order 8260.51, United States Standard for Required Navigation Performance (RNP) Instrument Approach Procedure Construction, dated December 30, 2002. 1.4 Explanation of Changes. These criteria were written for automated implementation. Formulas are presented in Math notation and standard text to facilitate programming efforts.

Calculation examples were eliminated. Instead, an Adobe Acrobat version of the criteria document is available where each formula performs the calculation as an imbedded calculator. 1.4.1 Chapter 1. 1.4.1 a. Paragraph 1. Clarifies that these criteria support RNAV STARS, and T- Routes. 1.4.1 b. Paragraph 1.4. Reflects addition of new criteria. 1.4.1 c. Paragraph 1.6. Removes definition of nonprecision approach with vertical guidance (APV) and touchdown zone elevation (TDZE), replaces height above touchdown (HAT) definition with height above threshold (HATh), adds LP definition, and redefines Precise Final Approach Fix (PFAF). 1.4.2 Chapter 2. 1.4.2 a. Paragraph 2.0. Adds explanation of Math notation and support for RNAV STARS and T-routes. 1.4.2 b. Paragraph 2.1.2. Updates to reflect formulas are written for “radian” calculation. Changes the calculation value of a nautical mile (NM) from 6076.11548 to 1852/0.3048. Adds conversions to and from degrees/radians, feet to meters, meters to NM, NM to feet, and temperature Celsius to Fahrenheit. 1.4.2 c. Paragraph 2.1.3. Adds Geospatial standards. 1.4.2 d. Table 2-1. Adds LP. 1.4.2 e. Paragraph 2.3. Adds feeder segment. 1.4.2 f. Tables 2-2 and 2-3. Adds feeder segment. 1.4.2 g. Paragraph 2.4. Adds method for determining turn altitude. 1.4.2 h. Formula 2-1a. Updates to harmonize with International Civil Aviation Organization (ICAO). 1.4.2 i. Table 2-3. Adds feeder segment. 1.4.2 j. Formula 2-1b. Updates to be consistent with ICAO. 1.4.2 k. Formula 2-1c. Updates and renumbers radius formula for accuracy. Adds notes for bank limitations above FL 195.

1.4.2 l. Formula 2-2. Renumbers formula from 2-3 and provides clarification to more accurately represent 6 seconds using new definition of NM. 1.4.2 m. Figures 2-4 and 2-5. Updates figures for clarity. 1.4.2 n. Formula 2-5. Adds distance turn anticipation (DTA) computation. 1.4.2 o. Formula 2-7. Provides a formula to calculate minimum length of track to fix (TF) leg following a Fly-by turn. 1.4.2 p. Paragraph 2.5.3. Adds radius to fix (RF) turn criteria. 1.4.2 q. Figure 2-7. Renumbers figure to 2-8. 1.4.2 r. Formula 2-5. Updates and renumbers formula to 2-8. 1.4.2 s. Paragraph 2.7. Adds feeder segment. 1.4.2 t. Section 2. Renumbers paragraph starting with 2.8. 1.4.2 u. Paragraph 2.8.1. Adds course reversal. 1.4.2 v. Formula 2-6. Renumbers formula to 2-9. 1.4.2 w. Paragraph 2.8.6. Adds Holding Pattern Initial Segment. 1.4.2 x. Paragraph 2.8. Renumbers paragraph to 2.9. Adds standards for LNAV/VNAV, LNAV, and LP. Renumbers figures for intermediate segment. Adds additional figures supporting offset intermediate segment construction. 1.4.2 y. Formula 2-7. Renumbers formula to 2-10.

Updates to be consistent with new definition of nautical mile. 1.4.2 z. Table 2-4. Adds LPV glidepath angle restrictions for HATh values < 250. 1.4.2 aa. Table 2-5. Deletes Standard LPV Landing Minimums. Adds reference to Order 8260.3B, United States Standard for Terminal Instrument Procedures (TERPS) chapter 3. Renumbers the remaining tables. 1.4.2 bb. Paragraph 2.13. Renumbers paragraph "Determining Precise Final Approach Fix/Final Approach Fix (PFAF/FAF) Coordinates. Revises to calculate PFAF based on Barometric vertical navigation (BaroVNAV) when publishing combined procedures (LPV with LNAV/VNAV). Adds associated formulas. 1.4.2 cc. Section 4. Adds "Missed Approach General Information."

1.4.3 Chapter 3.

Adds "Non vertically Guided Procedures" and LP and LNAV segment construction. 1.4.4 Chapter 4.

Adds "Lateral Navigation with Vertical Guidance (LNAV/VNAV)." 1.4.5 Chapter 5. 1.4.5 a. Paragraph 5.1.4. Removes paragraph and incorporates in paragraph 5.2.2, formula 5-5. 1.4.5 b. Paragraph 5.2. Changes how obstacle surfaces are applied. All final segment obstacle clearance surface (OCS) [W, X, and Y] obstacles are evaluated relative to the height of the W surface based on their along-track distance (OBSX) from the landing threshold point (LTP), perpendicular distance (OBSY) from the course centerline, and mean sea level (MSL) elevation (OBSMSL) adjusted for earth curvature and X/Y surface rise if appropriate. This changes the numbering of subsequent formulas. 1.4.5 c. Paragraph 5.8. Adds section 1 of the LPV missed approach segment. 1.4.6 Chapter 6.

Reorganizes chapter 6 for simplification. Renumbers paragraphs and formulas. Updates figures for clarity and some re-labeling. Most of the figures are full page illustrations; therefore, all figures are grouped at the end of the chapter. 1.4.7 Appendix 1.

This appendix provides a listing of formulas in text format. 1.4.8 Appendix 2.

This appendix provides the standard geodetic formulas for use in development of TERPS instrument procedures. 1.5 Background.

The National Airspace System (NAS) is evolving from a system of conventional ground based navigational aids [VHF omnidirectional radio range (VOR), nondirectional radio beacon (NDB), etc.] to a system based on RNAV [GPS, wide area augmentation system (WAAS), local area augmentation system (LAAS), etc.]

and RNP. This order provides criteria for the application of obstacle clearance standards to approaches based on RNAV. 1.6 Effective Date. January 1, 2008 1.7 Definitions. 1.7.1 Along-Track Distance (ATD).

A distance specified in nautical miles (NM) along a defined track to an RNAV fix. 1.7.2 Along-Track (ATRK) Tolerance (ATT). The amount of possible longitudinal fix positioning error on a specified track expressed as a ± value (see figure 1-1).

Figure 1-1. ATT.

Along-track

tolerance.

Note: The acronym ATRK FDT (along-track fix displacement tolerance) has been used instead of ATT in the past. The change to ATT is a step toward harmonization of terms with ICAO Pans-Ops. 1.7.3 Barometric Altitude.

A barometric altitude measured above mean sea level (MSL) based on atmospheric pressure measured by an aneroid barometer. This is the most common method of determining aircraft altitude. 1.7.4 Cross-Track (XTT) Tolerance.

The amount of possible lateral positioning error expressed as a ± value (see figure 1-2).

Figure 1-2. XTT.

Cross-track

tolerance.

Note: The acronym XTRK FDT (cross-track fix displacement tolerance) has been used instead of XTT in the past. The change to XTT is a step toward harmonization of terms with ICAO Pans-Ops. 1.7.5 Decision Altitude (DA).

The DA is a specified barometric altitude at which a missed approach must be initiated if the required visual references to continue the approach have not been acquired. DA is referenced to MSL. It is applicable to vertically guided approach procedures. 1.7.6 Departure End of Runway (DER).

The DER is the end of the runway that is opposite the landing threshold. It is sometimes referred to as the stop end of runway. 1.7.7 Distance of Turn Anticipation (DTA).

DTA represents the maximum distance from (prior to) a fly-by-fix that an aircraft is expected to start a turn to intercept the course of the next segment. The ATT value associated with a fix is added to the DTA value when DTA is applied (see figure 1-3).

Figure 1-3. DTA.

DTA radius x ( degrees of turn 2) ÷ tan

ATT

1.7.8 Fictitious Threshold Point (FTP). The FTP is the equivalent of the landing threshold point (LTP) when the final approach course is offset from the runway centerline and is not aligned through the LTP. It is the intersection of the final course and a line perpendicular to the final course that passes through the LTP. FTP elevation is the same as the LTP (see figure 1-4). For the purposes of this document, where LTP is used, FTP may apply as appropriate.

Jan 26 2005 Policy Memo

Figure 1-4. FTP.

1.7.9 Fix Displacement Tolerance (FDT).

FDT is a legacy term providing 2-dimensional (2D) quantification of positioning error. It is now defined as a circular area with a radius of ATT centered on an RNAV fix (see figure 1-3). The acronym ATT is now used in lieu of FDT. 1.7.10 Flight Path Alignment Point (FPAP).

The FPAP is a 3-dimensional (3D) point defined by World Geodetic System of 1984/North American Datum of 1983 (WGS-84/NAD-83) latitude, longitude, MSL elevation, and WGS-84 Geoid height. The FPAP is used in conjunction with the LTP and the geometric center of the WGS-84 ellipsoid to define the final approach azimuth (LPV glidepath’s vertical plane) associated with an LP or LPV final course. 1.7.11 Geoid Height (GH).

The GH is the height of the Geoid relative to the WGS-84 ellipsoid. It is a positive value when the Geoid is above the WGS-84 ellipsoid and negative when it is below. The value is used to convert an MSL elevation to an ellipsoidal or geodetic height - the height above ellipsoid (HAE). Note: The Geoid is an imaginary surface within or around the earth that is everywhere normal to the direction of gravity and coincides with mean sea level (MSL) in the oceans. It is the reference surface for MSL heights. 1.7.12 Glidepath Angle (GPA).

The GPA is the angle of the specified final approach descent path relative to a horizontal line tangent to the surface of the earth at the runway threshold (see figure 1-5). In this order, the glidepath angle is represented in formulas and figures as the Greek symbol theta (θ ).

1.7.13 Glidepath Qualification Surface (GQS).

The GQS is a narrow inclined plane centered on the runway centerline that limits the height of obstructions between the DA and LTP. A clear GQS is required for authorization of vertically-guided approach procedure development. 1.7.14 Height Above Ellipsoid (HAE).

The elevation of the glidepath origin (threshold crossing height [TCH] point) for an LPV approach procedure is referenced to the LTP. RNAV avionics calculate heights relative to the WGS-84 ellipsoid. Therefore, it is important to specify the HAE value for the LTP. This value differs from a height expressed in feet above the geoid (essentially MSL) because the reference surfaces (WGS-84 ellipsoid and the geoid) do not coincide. Ascertain the height of the orthometric geoid (MSL surface) relative to the WGS-84 ellipsoid at the LTP. This value is considered the GH. For Westheimer Field, Oklahoma the GH is -87.29 ft. This means the geoid is 87.29 ft below the WGS-84 ellipsoid at the latitude and longitude of the runway 35 threshold. To convert an MSL height to an HAE height, algebraically add the geoid height* value to the MSL value. HAE elevations are not used for instrument procedure construction, but are documented for inclusion in airborne receiver databases. NOTE for users of the Aviation System Standards Information System (AVNIS) Database: The “Ellipsoid Elev” field value is the HAE for the runway threshold.

Formula 1-1. HAE Example.

HAE Z GH = +

Runway ID ANYTOWN RWY 35

Latitude 35°14’31.65” N

Longitude 97°28’22.84” W

MSL Elevation (Z) 1117.00

Given Variables

Geoid Height* (GH) -87.146 feet

Z+GH

Calculator

Z =

GH = Calculation

HAE = * Calculate GH for CONUS using NGS GEOID03 program, for Alaska, use GEOID06. See the NGS website - http://www.ngs.noaa.gov/TOOLS/.

Click Here to

Calculate

Click Here to Calculate

1.7.15 Height Above Threshold (HATh). The HATh is the height of the DA above LTP elevation; i.e.,

Formula 1-2. HATh Example.

elev HATh DA LTP = −

DA-LTPelev

Calculator

LTPelev

DA

HATh

Click Here

to Calculate 1.7.16 Inner-Approach Obstacle Free Zone (OFZ). The inner-approach OFZ is the airspace above a surface centered on the extended runway centerline. It applies to runways with an approach lighting system of any authorized type. (USAF NA) 1.7.17 Inner-Transitional OFZ. The inner-transitional OFZ is the airspace above the surfaces located on the outer edges of the runway OFZ and the inner-approach OFZ. It applies to runways with approach visibility minimums less than ¾ statute miles (SM). (USAF NA) 1.7.18 Landing Threshold Point (LTP). The LTP is a 3D point at the intersection of the runway centerline and the runway threshold (RWT). WGS-84/NAD-83 latitude, longitude, MSL elevation, and geoid height define it. It is used in conjunction with the FPAP and the geometric center of the WGS-84 ellipsoid to define the vertical plane of an RNAV final approach course (see figure 1-5). (USAF must use WGS-84 latitude and longitude only.) Note: Where an FTP is used, apply LTP elevation (LTPE).

Figure 1-5. LTP.

1.7.19 Lateral Navigation (LNAV). LNAV is RNAV lateral navigation. This type of navigation is associated with nonprecision approach procedures (NPA) because vertical path deviation information is not provided. LNAV criteria are the basis of the LNAV minima line on RNAV GPS approach procedures. 1.7.20 Lateral Navigation/Vertical Navigation (LNAV/VNAV). An approach with vertical guidance (APV) evaluated using the Baro VNAV obstacle clearance surfaces conforming to the lateral dimensions of the LNAV obstruction evaluation area (OEA). The final descent can be flown using Baro VNAV, or LPV vertical guidance in accordance with Advisory Circular (AC) 90-97, Operational Approval of Barometric VNAV Instrument Approach Operations Using Decision Altitude. 1.7.21 Localizer Performance (LP).

An LP approach is an RNAV NPA procedure evaluated using the lateral obstacle evaluation area dimensions of the precision localizer trapezoid, with adjustments specific to the WAAS. See chapter 3. These procedures are published on RNAV GPS approach charts as the LP minima line. 1.7.22 Localizer Performance with Vertical Guidance (LPV). An approach with vertical guidance (APV) evaluated using the OCS dimensions (horizontal and vertical) of the precision approach trapezoid, with adjustments specific to the WAAS. See chapter 5. These procedures are published on RNAV GPS approach charts as the LPV minima line. 1.7.23 Obstacle Evaluation Area (OEA). An area within defined limits that is subjected to obstacle evaluation through application of required obstacle clearance (ROC) or an obstacle clearance surface (OCS). 1.7.24 Obstacle Clearance Surface (OCS). An OCS is an upward or downward sloping surface used for obstacle evaluation where the flight path is climbing or descending. The separation between this surface and the vertical path angle defines the MINIMUM required obstruction clearance at any given point.

Policy Memo Aug 10 2011

1.7.25 Obstacle Positions (OBSX,Y,Z). OBSX, Y & Z are the along track distance to an obstacle from the LTP, the perpendicular distance from the centerline extended, and the MSL elevation, respectively, of the obstacle clearance surfaces. 1.7.26 Precise Final Approach Fix (PFAF).

The PFAF is a calculated WGS-84 geographic position located on the final approach course where the designed vertical path (NPA procedures) or glidepath (APV and PA procedures) intercepts the intermediate segment altitude (glidepath intercept altitude). The PFAF marks the beginning of the final approach segment (see figure 1-6). The calculation of the distance from LTP to PFAF includes the earth curvature.

Figure 1-6. PFAF.

1.7.27 Reference Datum Point (RDP).

The RDP is a 3D point defined by the LTP or FTP latitude/longitude position, MSL elevation, and a threshold crossing height (TCH) value. The RDP is in the vertical plane associated with the final approach course and is used to relate the glidepath angle of the final approach track to the landing runway. It is also referred to as the TCH point or flight path control point (FPCP) (see figure 1-7).

Figure 1-7. RDP, TCH, GPA (θ).

RDP

Orthometric Geoid

or WGS-84 Ellipsoid

LTP

Glidepath

ASBL

Parallel

lines

tangent point

TCH θ

Policy Memo Feb 9 2011

1.7.28 Runway Threshold (RWT).

The RWT marks the beginning of the part of the runway that is usable for landing (see figure 1-5). It includes the entire width of the runway. 1.7.29 Start of Climb (SOC). The SOC is the point located at a calculated along-track distance from the decision altitude/missed approach point (DA/MAP) where the 40:1 missed approach surface originates. 1.7.30 Threshold Crossing Height (TCH).

The height of the glidepath above the threshold of the runway measured in feet (see figure 1-7). The LPV glidepath originates at the TCH value above the LTP. 1.7.31 Visual Glide Slope Indicator (VGSI). The VGSI is an airport lighting aid that provides the pilot a visual indication of the aircraft position relative to a specified glidepath to a touchdown point on the runway. 1.7.32 Wide Area Augmentation System (WAAS). The WAAS is a navigation system based on the GPS. Ground correction stations transmit position corrections that enhance system accuracy and add satellite based VNAV features. 1.8 Information Update. For your convenience, FAA Form 1320-19, Directive Feedback Information, is included at the end of this order to note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this order. When forwarding your comments to the originating office for consideration, please use the "Other Comments" block to provide a complete explanation of why the suggested change is necessary.

Chapter 2. General Criteria › Section 1. Basic Criteria

Chapter 2. General Criteria

Section 1. Basic Criteria Information

2.0 General. The following FAA orders apply. 8260.3, United States Standard for Terminal Instrument Procedures (TERPS). 8260.19, Flight Procedures and Airspace. 7130.3, Holding Pattern Criteria. The feeder, initial, intermediate, final, and missed approach criteria described in this order supersede the other publications listed above. See TERPS, Volume 1, chapter 3 to determine visibility minima. The feeder criteria in paragraph 2.7 may be used to support RNAV Standard Terminal Arrival Route (STAR) and Tango (T) Air Traffic Service (ATS) route construction. Formulas are numbered by chapter and depicted in standard mathematical notation and in standard text to aid in computer programming. Each formula contains a java script functional calculator.

Formula x-x. Formula Title.

2 X Y

tan 3 180

= π ⎛ ⎞ ⋅ ⎜ ⎟ ⎝ ⎠

where X = variable value

x^2/tan(3*π/180)

Calculator

X input value here Click here

to calculate Y Calculated Result

2.1 Data Resolution. Perform calculations using an accuracy of at least 15 significant digits; i.e., floating point numbers must be stored using at least 64 bits. Do not round intermediate results. Round only the final result of calculations for documentation purposes. Required accuracy tolerance is 1 centimeter for distance and 0.002 arc-second for angles. The following list specifies the minimum accuracy standard for documenting data expressed numerically. This standard

Click here after entering input values to make the calculator

function

Enter variable

values in the

green areas

The calculated answer is

printed after the grey

button is clicked

Formula in math notation

Formula in standard text

notation

applies to the documentation of final results only; e.g., a calculated adjusted glidepath angle of 3.04178 degrees is documented as 3.05 degrees. The standard does not apply to the use of variable values during calculation. Use the most accurate data available for variable values. 2.1.1 Documentation Accuracy: 2.1.1 a. WGS-84 latitudes and longitudes to the nearest one hundredth (0.01) arc second; [nearest five ten thousandth (0.0005) arc second for Final Approach Segment (FAS) data block entries]. 2.1.1 b. LTP mean sea level (MSL) elevation to the nearest foot; 2.1.1 c. LTP height above ellipsoid (HAE) to the nearest tenth (0.1) meter; 2.1.1 d. Glidepath angle to the next higher one hundredth (0.01) degree; 2.1.1 e. Courses to the nearest one hundredth (0.01) degree; and 2.1.1 f. Course width at threshold to the nearest quarter (0.25) meter; 2.1.1 g. Distances to the nearest hundredth (0.01) unit [except for “length of offset” entry in FAS data block which is to the nearest 8 meter value]. 2.1.2 Mathematics Convention. Formulas in this document as depicted are written for radian calculation. Note: The value for 1 NM was previously defined as 6,076.11548 ft. For the purposes of RNAV criteria, 1 NM is defined as the result of the following calculation:

1852 0.3048

2.1.2 a. Conversions:

• Degree measure to radian measure:

radians degrees 180

π = i

• Radian measure to degree measure:

180 degrees radians = π i

• Feet to meters:

meters feet 0.3048 = i

• Meters to feet

meters feet 0.3048 =

• Feet to Nautical Miles (NM)

0.3048 NM feet 1852 = ⋅

• NM to feet:

1852 feet NM 0.3048 = i

• NM to meters meters NM 1852 = i

• Meters to NM

meters NM 1852 =

• Temperature Celsius to Fahrenheit:

Fahrenheit Celcius T 1.8 T 32 = + i

• Temperature Fahrenheit to Celsius

Fahrenheit Celcius

T 32 T 1.8 − =

2.1.2 b. Definition of Mathematical Functions and Constants. b a + indicates addition b a − indicates subtraction or o a b ab r or a b a*b × ⋅ indicates multiplication

a a a b b or or b ÷ indicates division

( ) b a − indicates the result of the process within the parenthesis b - a indicates absolute value ≈ indicates approximate equality 0.5 a a a or or ^0.5 indicates the square root of quantity "a" 2 or a a^2 indicates a a × ( ) ( ) or ln a log a indicates the natural logarithm of "a"

( ) a tan indicates the tangent of "a" degrees ( ) ( ) 1 or tan a atan a − indicates the arc tangent of "a" ( ) a sin indicates the sine of "a" degrees ( ) ( ) 1 or sin a asin a − indicates the arc sine of "a" ( ) a cos indicates the cosine of "a" degrees ( ) ( ) 1 or cos a acos a − indicates the arc cosine of "a" e The constant e is the base of the natural logarithm and is sometimes

known as Napier’s constant, although its symbol (e) honors Euler. With the possible exception of π, e is the most important constant in mathematics since it appears in myriad mathematical contexts involving limits and derivatives. Its value is approximately 2.718281828459045235360287471352662497757... r The TERPS constant for the mean radius of the earth for spherical

calculations in feet. r = 20890537 2.1.2 c. Operation Precedence (Order of Operations). First: Grouping Symbols: parentheses, brackets, braces, fraction bars, etc. Second: Functions: Tangent, sine, cosine, arcsine, and other defined functions Third: Exponentiations: Powers and roots Fourth: Multiplication and Division: Products and quotients Fifth: Addition and subtraction: Sums and differences e.g., 1 2 3 5 − = × − because multiplication takes precedence over subtraction ( ) 4 2 3 5 = × − because parentheses take precedence over multiplication

12 3 62 = because exponentiation takes precedence over division

5 16 9 = + because the square root sign is a grouping symbol 7 16 9 = + because roots take precedence over addition

( ) 1 5 . 0 30 sin = ° because functions take precedence over division

30 08660254 05 sin . .

° ⎛ ⎞= ⎜ ⎟ ⎝ ⎠ because parentheses take precedence over functions

Notes on calculator usage:

1. Most calculators are programmed with these rules of precedence.

2. When possible, let the calculator maintain all of the available digits of a number in memory rather than re-entering a rounded number. For highest accuracy from a calculator, any rounding that is necessary should be done at the latest opportunity.

2.1.3 Geospatial Standards. The following standards apply to the evaluation of obstacle and terrain position and elevation data relative to RNAV OEAs and OCSs. Terrain and obstacle data are reported in NAD-83 latitude, longitude, and elevation relative to MSL in National Geodetic Vertical Datum of 1929 (NGVD-29) or North American Vertical Datum of 1988 (NAVD-88) vertical datum. Evaluate obstacles using their NAD-83 horizontal position and NAVD-88 elevation value compared to the WGS-84 referenced course centerline (along-track and cross-track), OEA boundaries, and OCS elevations as appropriate. 2.1.3 a. WGS-84[G873] for Position and Course Construction. This reference frame is used by the FAA and the U.S. Department of Defense (DoD). It is defined by the National Geospatial-Intelligence Agency (NGA) (formerly the National Imagery and Mapping Agency, formerly the Defense Mapping Agency [DMA]). In 1986, the Office of National Geodetic Survey (NGS), redefined and readjusted the North American Datum of 1927 (NAD-27), creating the North American Datum of 1983 (NAD-83).

The WGS-84 was defined by the DMA. Both NAD-83 and WGS-84 were originally defined (in words) to be geocentric and oriented as the Bureau International d I’Heure (BIH) Terrestrial System. In principle, the three-dimensional (3D) coordinates of a single physical point should therefore be the same in both NAD-83 and WGS-84 Systems; in practice; however, small differences are sometimes found. The original intent was that both systems would use the Geodetic Reference System of 1980 (GRS-80) as a reference ellipsoid. As it happened, the WGS-84 ellipsoid differs very slightly from GRS-80). The difference is 0.0001 meters in the semi-minor axis. In January 2, 1994, the WGS-84 reference system was realigned to be compatible with the International Earth Rotation Service’s Terrestrial Reference Frame of 1992 (ITRF) and renamed WGS-84 (G730). The reference system underwent subsequent improvements in 1996, referenced as WGS-84 (G873) closely aligned with ITRF-94, to the current realization adopted by the NGA in 2001, referenced as WGS-84 (G1150) and considered equivalent systems to ITRF 2000.

2.1.3 b. NAVD-88 for elevation values. NAVD-88 is the vertical control datum established in 1991 by the minimum-constraint adjustment of the Canadian-Mexican- U.S. leveling observations. It held fixed the height of the primary tidal bench mark, referenced to the new International Great Lakes Datum of 1985 local MSL height value, at Father Point/Rimouski, Quebec, Canada. Additional tidal bench mark elevations were not used due to the demonstrated variations in sea surface topography, (i.e., the fact that MSL is not the same equipotential surface at all tidal bench marks). 2.1.3 c. OEA Construction and Obstacle Evaluation Methodology. 2.1.3 c. (1) Courses, fixes, boundaries (lateral dimension). Construct straight-line courses as a WGS-84 ellipsoid geodesic path. If the course outbound from a fix differs from the course inbound to the fix (courses measured at the fix), then a turn is indicated. Construct parallel and trapezoidal boundary lines as a locus of points

measured perpendicular to the geodesic path. (The resulting primary and/or secondary boundary lines do not display a “middle bulge” due to curvature of the ellipsoids surface since they are not geodesic paths.) NAD-83 latitude/longitude positions are acceptable for obstacle, terrain, and airport data evaluation. Determine obstacle lateral positions relative to course centerline/OEA boundaries using ellipsoidal calculations (see appendix 2). 2.1.3 c. (2) Elevations (vertical dimension). Evaluate obstacles, terrain, and airport data using their elevation relative to their orthometric height above the geoid (for our purposes, MSL) referenced to the NAVD-88 vertical datum. The elevations of OCSs are determined spherically relative to their origin MSL elevation (NAVD-88). Department of Defense (DoD) procedure developers may use EGM-96 vertical datum. 2.1.4 Evaluation of Actual and Assumed Obstacles (AAO). Apply the vertical and horizontal accuracy standards in Order 8260.19, paragraphs 272, 273, 274, and appendix 3. (USAF, apply guidance per AFI 11-230) Note: When applying an assumed canopy height consistent with local area vegetation, contact either the National Forestry Service or the FAA regional Flight Procedures Office (FPO) to verify the height value to use. 2.1.5 ATT Values. ATT is the value used (for segment construction purposes) to quantify position uncertainty of an RNAV fix. The application of ATT can; therefore, be considered “circular;” i.e., the ATT value assigned describes a radius around the plotted position of the RNAV fix (see figure 2-1 and table 2-1).

Figure 2-1. ATT.

Fix displacement

Note: Cross-track tolerance (XTT) values were considered in determining minimum segment widths, and are not considered further in segment construction.

Table 2-1. ATT Values.

En Route (STARs, SIDs, Feeder, Initial, Intermediate, Missed Approach > 30 NM) 2.0 NM

Terminal (STARS, SIDs, Feeder, Initial, Intermediate, Missed Approach ≤ 30 NM) 1.0 NM GPS

Approach

(final) 0.3 NM

WAAS* (LPV & LP)

Approach

(final) 40 meters

*Applies to final segment only. Apply GPS values to all other segments of the approach procedure. 2.2 Procedure Identification. Title RNAV procedures based on GPS or WAAS: “RNAV (GPS) RWY XX.” Where more than one RNAV titled approach is developed to the same runway, identify each with an alphabetical suffix beginning at the end of the alphabet. Procedures with the lowest minimums should normally be titled with a “Z” suffix.

Examples RNAV (GPS) Z RWY 13 (Lowest HATh: example 200 ft) RNAV (RNP) Y RWY 13 (2nd lowest HATh: example 278 ft) RNAV (GPS) X RWY 13 (3rd lowest HATh: example 360 ft) Note: Operational requirements may occasionally require a different suffix grouping; e.g., “Z” suffix procedures are RNP SAAAR, “Y” suffix procedures contain LPV, etc. 2.3 Segment Width (General). Table 2-2 lists primary and secondary width values for all segments of an RNAV approach procedure. Where segments cross* a point 30 NM from airport reference point (ARP), segment primary area width increases (expansion) or decreases (taper) at a rate of 30 degrees relative to course to the appropriate width (see figure 2-3). Secondary area expansion/taper is a straight-line connection from the point the primary area begins expansion/taper to the point the primary area expansion/taper ends (see figure 2-2). Reference to route width values is often specified as NM values measured from secondary area edge across the primary area to the secondary edge at the other side. For example, route width for segments more than 30 NM from ARP is “2-4-4-2.” For distances ≤ 30 NM, the width is “1-2-2-1.” See table 2-2 and figures 2-2 and 2-3. *Note: STARs and Feeder segment width is 2-4-4-2 at all distances greater than 30 NM from ARP. A segment designed to cross within 30 NM of the ARP more than

once does not taper in width until the 30 NM limit is crossed for approach and landing; i.e., crosses the limit for the last time before landing. A missed approach segment designed to cross a point 30 NM of the ARP more than once expands when it crosses the boundary the first time and remains expanded.

Table 2-2. RNAV Linear Segment Width (NM) Values.

Segment Primary Area Half-Width (p) Secondary Area (s)

± 4.00 2.00 STARs, Feeder, Initial & Missed

Approach

> 30

NM from

ARP

2-4-4-2

± 2.00 1.00 STARs, Feeder,

Initial, Missed

Approach

≤ 30 NM

from

ARP 1-2-2-1

Intermediate

Continues initial segment width until 2 NM prior to PFAF. Then tapers uniformly to final segment width.

Continues initial segment width until 2 NM prior to PFAF. Then it tapers to final segment width.

Figure 2-2. Segment Width Variables.

S P S P

Figure 2-3a. Segment Width Changes at 30 NM.

4 NM 2 NM

2.0 NM 2.0 NM 1NM 1NM

2 NM 4 NM

4 NM 2 NM

2.0 NM 2.0 NM 1NM 1NM

2 NM 4 NM

30 NM from ARP

2.3.1 Width Changes at 30 NM from ARP (non-RF). Receiver sensitivity changes at 30 NM from ARP. From the point the designed course crosses 30 NM from ARP, the primary OEA can taper inward at a rate of 30 degrees relative to course from ± 4 NM to ± 2 NM. The secondary area tapers from a 2 NM width when the 30 NM point is crossed to a 1 NM width abeam the point the primary area reaches the ± 2 NM width. The total along-track distance required to complete the taper is approximately 3.46 NM (21,048.28 ft). Segment width tapers regardless of fix location within the tapering section unless a turn is associated with the fix. Delay OEA taper until the turn is complete and normal OEA turn construction is possible. EXCEPTION: The taper may occur in an RF turn segment if the taper begins at least 3.46 NM (along-track distance) from the RF leg termination fix; i.e., if it is fully contained in the RF leg. 2.3.2 Width Changes at 30 NM from ARP (RF). When the approach segment crosses the point 30 NM from airport reference point in an RF leg, construct the leg beginning at a width of 2-4-4-2 prior to the 30 NM point and taper to 1-2-2-1 width after the 30 NM point. Calculate the perpendicular distance (Bprimary, Bsecondary) from the RF segment track centerline to primary and secondary boundaries at any along-track distance (specified as degrees of RF arc “α”) from the point the track crosses the 30 NM point using formula 2-1 (see figure 2-3b).

Formula 2-1. RF Segment Taper Width.

primary

secondary

Calculates degrees of arc ( )

4-2 180 D D= R tan 30 180

R B 4 2

to com

180 D

R B 6 3 18

plete tap r

0 D

e

⋅ α = π π ⋅ ⎛ ⎞ ⋅ ⎜ ⎟ ⎝ ⎠

φ ⋅π ⋅ = − ⋅ ⋅

φ ⋅π ⋅

α

= − ⋅ ⋅

where R = RF leg radius φ = degrees of arc (RF track)

Note: “D” will be in the same units as “R”

α = (180*D)/(π*R) Bprimary = 4-2*(φ*π*R)/(180*D) Bsecondary = 6-3*(φ*π*R)/(180*D)

Calculator

R

φ

α

D

Bprimary

Bsecondary

Click Here

to Calculate

°

°

Figure 2-3b. Segment Width Changes in RF Leg

(advanced avionics required).

R

R

φ

α

D

30 NM from ARP

Bsecondary

Bprimary

2.4 Calculating the Turn Radius (R). The design turn radius value is based on four variables: indicated airspeed, assumed tailwind, altitude, and bank angle. Apply the indicated airspeed from table 2-3 for the highest speed aircraft category that will be published on the approach procedure. Apply the highest expected turn altitude value. The design bank angle is assumed to be 18 degrees. Note: Determine the highest altitude within a turn by:

For approach –calculate the vertical path altitude (VPalt) by projecting a 3-degree vertical path from the PFAF along the designed nominal flight track to the turn fix (see formula 2-2).

Policy Memo Jul 15 2011

Formula 2-2. Vertical Path Altitude.

( )

Z D tan 3 180

r alt alt VP e r PFAF r

π ⎛ ⎞ ⋅ ⋅ ⎜ ⎟ ⎝ ⎠ = ⋅ + − where PFAFalt = Designed PFAF MSL altitude θ = glidepath angle DZ = distance (ft) from PFAF to fix Note: If DZ is a NM value, convert to feet by multiplying NM by 1852/0.3048

e^((DZ*tan(3*π/180))/r)*(r+PFAFalt)-r

Calculator

PFAFalt

θ

DZ

VPalt

Click Here

to Calculate

For missed approach – project a vertical path along the nominal flight track from the SOC point and altitude to the turn fix, that rises at a rate of 250 ft/NM (Cat A/B), 500 ft/NM (Cat C/D) or a higher rate if a steeper climb gradient is specified. For turn at altitude construction, determine the altitude to calculate VKTAS based on the climb-to altitude plus an additive based on a continuous climb of 250 (Cat A/B)or 500 (Cat C/D) ft per 12 degrees of turn [ φ*250/12 or φ*500/12 ] (not to exceed the missed approach altitude). Cat D example: 1,125 ft would be added for a turn of 27 degrees, 958 ft would be added for 23 degrees, 417 ft for 10 degrees of turn. Compare the vertical path altitude at the fix to minimum published fix altitude. The altitude to use is the higher of the two. For missed approach, the turn altitude must not be higher than the published missed approach altitude. STEP 1: Determine the true airspeed (KTAS) for the turn using formula 2-3a. Locate and use the appropriate knots indicated airspeed (KIAS) from table 2-3. Use the highest altitude within the turn.

°

Formula 2-3a. True Airspeed.

( )

( )

KIAS KTAS 2.628 V 171233 288 15 0.00198 alt V

288 0.00198 alt

⋅ ⋅ + − ⋅ =

− ⋅

where alt = aircraft MSL elevation VKIAS = knots indicated airspeed

(VKIAS*171233*((288+15)-0.00198*alt)^0.5)/(288-0.00198*alt)^2.628

Calculator

VKIAS

alt

VKTAS

Click Here to Calculate

Table 2-3. Indicated Airspeeds (Knots).

Indicated Airspeed by Aircraft Category (CAT) Segment

CAT A CAT B CAT C CAT D CAT E

Feeder, Initial Intermediate,

Missed Approach

Above 10,000 180 250 300 300 350

Feeder, Initial

Intermediate At/Below 10,000 150 250

Final 90 120 140 165 165 or as Specified*

Missed Approach (MA) 110 150 240 265 265 or as Specified* * Record Cat E final or MA indicated airspeed in procedure documentation if different than listed. STEP 2: Calculate the appropriate tailwind component (VKTW) using formula 2-3b for the highest altitude within the turn. EXCEPTION: If the MSL altitude is 2,000 ft or less above airport elevation, use 30 knots.

Policy Memo Oct 19 2010

Policy Memo Oct 19 2010

Formula 2-3b. Tailwind.

= ⋅ + KTW V 0.00198 alt 47 where alt = highest turn altitude

Note: If “alt” is 2000 or less above

airport elevation, then VKTW = 30

0.00198*alt+47

Calculator

alt

VKTW

Click Here to Calculate

*Greater tailwind component values may be used where data indicates higher wind conditions are likely to be encountered. Where a higher value is used, it must be recorded in the procedure documentation. STEP 3: Calculate R using formula 2-3c.

Formula 2-3c. Turn Radius.

( )

2

KTAS KTW

angle

V V R

tan bank 68625.4 180

+ = π ⎛ ⎞ ⋅ ⋅ ⎜ ⎟ ⎝ ⎠

where bankangle = assumed bank angle (normally 14° for Cat A, 18° for Cats B-D)

(VKTAS+VKTW)^2/(tan(bankangle*π/180)*68625.4)

Calculator

VKTAS

VKTW

bankangle

R

Click Here

to Calculate

Note 1: (formula 2-3c) For fly-by turns where the highest altitude in the turn is between 10,000 ft and flight level 195, where the sum of “VKTAS+VKTW” is greater than 500 knots, use 500 knots.

Note 2: (formula 2-3c) For fly-by turns, where the highest altitude in the turn is greater than flight level 195, use 750 knots as the value for “VKTAS+VKTW” and 5 degrees of bank rather than 18 degrees. If the resulting DTA is greater than 20 NM,

Policy Memo Oct 19 2010

Policy Memo Oct 19 2010

°

then 20 R

tan 2 180

= φ π ⎛ ⎞ ⋅ ⎜ ⎟ ⎝ ⎠

where φ is the amount of turn (heading change). Use formula

2-8 to verify the required bank angle does not exceed 18 degrees. 2.5 Turn Construction. If the course outbound from a fix differs from the course inbound to the fix (courses measured at the fix), a turn is indicated. 2.5.1 Turns at Fly-Over Fixes (see figures 2-4 and 2-5). 2.5.1 a. Extension for Turn Delay. Turn construction incorporates a delay in start of turn to account for pilot reaction time and roll-in time (rr). Calculate the extension distance in feet using formula 2-4.

Formula 2-4. Reaction & Roll Dist.

KTAS

1852 0.3048 rr 6 V 3600 = ⋅ ⋅

6*1852/0.3048/3600*VKTAS

Calculator

VKTAS

rr

Click Here

to Calculate STEP 1: Determine R. See formula 2-3c. STEP 2: Determine rr. See formula 2-4. STEP 3: Establish the baseline for construction of the turn expansion area as the line perpendicular to the inbound track at a distance past the turn fix equal to (ATT+rr). STEP 4: On the baseline, locate the center points for the primary and secondary turn boundaries. The first is located at a distance R from the non-turning side primary boundary. The second is located at a distance R from the turning side secondary boundary (see figures 2-4 and 2-5). STEP 5: From these center points construct arcs for the primary boundary of radius R. Complete the secondary boundary by constructing additional arcs of radius (R+WS) from the same center points. (WS=width of the secondary). This is shown in figures 2-4 and 2-5.

STEP 6: The arcs constructed in step 5 are tangent to the outer boundary lines of the inbound segment. Construct lines tangent to the arcs based on the first turn point tapering inward at an angle of 30 degrees relative to the outbound track that joins the arc primary and secondary boundaries with the outbound segment primary and secondary boundaries. If the arcs from the second turn point are inside the tapering lines as shown in figure 2-4, then they are disregarded and the expanded area construction is completed. If not, proceed to step 7.

Figure 2-4. Fly-Over with No Second Arc Expansion.

SECONDARY AREA

LATEATT

Evaluated as both segments A and B

EARLY ATT

rr

PRIMARY AREA

PRIMARY AREA

INBOUND SEGMENT A

OUTBOUND SEGMENT B

PRIMARY AREA

PRIMARY AREA

SECONDARY AREA

SECONDARY AREA

R

R

SECONDARY AREA

STEP 3

STEP 4

STEP 5

STEP 6

STEP 8

STEP 7: If both the inner and outer arcs lie outside the tapering lines constructed in step 6, connect the respective inner and outer arcs with tangent lines and then construct the tapering lines from the arcs centered on the second center point as shown in figure 2-5.

STEP 8: The inside turn boundaries are the simple intersection of the preceding and succeeding segment primary and secondary boundaries.

Figure 2-5. Fly-Over with Second Arc Expansion.

SECONDARY AREA

LATE ATT EARLY ATT

rr

PRIMARY AREA

PRIMARY AREA

INBOUND SEGMENT A

OUTBOUND SEGMENT B

SECONDARY AREA

PRIMARY AREA

R

R

SECONDARY AREA

STEP 4

STEP 5

STEP 7

Evaluated as both segments A and B

STEP 3

STEP 8

The inbound OEA end (± ATT) is evaluated for both inbound and outbound segments. 2.5.1 b. Minimum length of TF leg following a fly-over turn. The leg length of a TF leg following a fly-over turn must be sufficient to allow the aircraft to return to course centerline. Determine the minimum leg length (L) using formulas 2-5 and 2-6.

Formula 2-5. Distance of Turn Anticipation.

DTA R tan 2 180

φ π ⎛ ⎞ = ⋅ ⋅ ⎜ ⎟ ⎝ ⎠

where R = turn radius from formula 2-3c

φ = degrees of heading change

DTA ATT

φ

R

R*tan(φ/2*π/180)

Calculator

R

φ

DTA

Click Here

to Calculate °

Formula 2-6. TF Leg Minimum Length Following Fly-Over Turn.

L f1 cos 3 sin R sin 4 3 3 cos DTA f2 180 180 180 180 ⎛ ⎞ ⎛ ⎞ π π π π ⎛ ⎞ ⎛ ⎞ ⎛ ⎞ ⎛ ⎞ = ⋅ φ ⋅ + ⋅ φ ⋅ + ⋅ φ ⋅ + − − ⋅ φ ⋅ + + ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠

where R = turn radius (NM) from formula 2-3c φ = degrees of track change at fix f1 = ATT (NM) of fly-over fix (segment initial fix) f2 = ATT (NM) of segment termination fix DTA = value from formula 2-5 (applicable only if the fix is “fly-by”)

L

R

R

30°

30° 30°

φ

φ

f1 f1

f2 DTA

f1*(cos(φ*π/180)+3^0.5*sin(φ*π/180))+R*(sin(φ*π/180)+4-3^0.5-3^0.5*cos(φ*π/180))+DTA+f2

Calculator

f1

f2

φ

R

DTA

L

Click Here

to Calculate

°

2.5.2 Fly-By Turn. See figure 2-6. STEP 1: Establish a line through the turn fix that bisects the turn angle. Determine Turn Radius (R). See formula 2-3c. Scribe an arc (with origin on bisector line) of radius R tangent to inbound and outbound courses. This is the designed turning flight path. STEP 2: Scribe an arc (with origin on bisector line) that is tangent to the inner primary boundaries of the two segment legs with a radius equal to Primary Area Half-width

2

(example: half width of 2 NM, the radius would be R+1.0 NM). STEP 3: Scribe an arc that is tangent to the inner secondary boundaries of the two segment legs using the origin and radius from step 2 minus the secondary width. STEP 4: Scribe the primary area outer turning boundary with an arc with a radius equal to the segment half width centered on the turn fix. STEP 5: Scribe the secondary area outer turning boundary with the arc radius from step 4 plus the secondary area width centered on the turn fix.

Figure 2-6. Fly-By Turn Construction.

STEP 5

STEP 4

STEP 3

STEP 2

STEP 1

SECONDARY AREA

SEGMENT A

SEGMENT B

PRIMARY AREA

PRIMARY AREA

PRIMARY AREA

PRIMARY AREA

SECONDARY AREA

SECONDARY AREA

SECONDARY AREA

Evaluated as both segments A and B

Bisector Line

2.5.2 a. Minimum length of track-to-fix (TF) leg following a fly-by turn. Calculate the minimum length for a TF leg following a fly-by turn using formula 2-7.

Formula 2-7. TF Leg Minimum

Length Following Fly-by Turn.

L f1 DTA1 DTA2 f2 = + + + where f1 = ATT of initial fix f2 = ATT of termination fix R1 = turn radius for first fix from formula 2-3c R2 = turn radius for subsequent fix from formula 2-3c Note: zero when φ2 is fly-over φ1 = degrees of heading change at initial fix

φ2 = degrees of heading change at termination fix

1 DTA1 R1 tan 2 180 φ π ⎛ ⎞ = ⋅ ⋅ ⎜ ⎟ ⎝ ⎠

2 DTA2 R2 tan 2 180 φ π ⎛ ⎞ = ⋅ ⋅ ⎜ ⎟ ⎝ ⎠

Note: zero when φ2 is fly-over

φ1 φ2

L

f1

DTA1 DTA2

f2

R1 R2

F1+DTA1+DTA2+F2

Calculator

f1

f2

R1

R2

φ1

φ2

DTA1

DTA2

L

Click Here

to Calculate °

°

2.5.3 Radius-to-Fix (RF) Turn. Incorporation of an RF segment may limit the number of aircraft served by the procedure. RF legs are used to control the ground track of a turn where obstructions prevent the design of a fly-by or fly-over turn, or to accommodate other operational requirements.* The curved leg begins tangent to the previous segment course at its terminating fix and ends tangent to the next segment course at its beginning fix (see figure 2-7). OEA construction limits turn radius to a minimum value equal-to or greater-than the OEA (primary and secondary) half-width. The RF segment OEA boundaries are parallel arcs. *Note: RF legs segments are not applicable to the final segment or section 1 of the missed approach segment. RF legs in the intermediate segment must terminate at least 2 NM prior to the PFAF. Where RF legs are used, annotate the procedure (or segment as appropriate) “RF Required.” Use Order 8260.52, table 1-3 for VKTW values for radius calculations for RF legs. STEP 1: Determine the segment turn radius (R) that is required to fit the geometry of the terrain/airspace. Enter the required radius value into formula 2-8 to verify the resultant bank angle is ≤ 20 degrees (maximum allowable bank angle). Where a bank angle other than 18 degrees is used, annotate the value in the remarks section of the FAA Form 8260-9 or appropriate military procedure documentation form.

Formula 2-8. RF Bank Angle.

( )

2

KTAS KTW angle

V V 180 bank a tan R 68625.4

⎛ ⎞ + ⎜ ⎟ = ⋅ ⎜ ⎟ ⋅ π ⎝ ⎠

where VKTAS = value from formula 2-3a

VKTW = value from Order 8260.52, table 1-3

R = required radius

atan((VKTAS+VKTW)^2/(R*68625.4))*180/π

Calculator

VKTAS

VKTW

R

bankangle

Click Here

to Calculate

Note: Where only categories A and B are published, verify the resultant bank angle is ≤ 15 degrees.

Policy Memo Oct 19 2010

Segment length may be calculated using formula 2-9.

Formula 2-9. RF Segment Length.

length

R Segment 180 π ⋅ ⋅φ =

where R = RF segment radius (answer will be in the units entered) φ = # of degrees of ARC

(heading change)

π*R*φ/180

Calculator

R

φ

Segmentlength

Click Here

to Calculate

STEP 2: Turn Center. Locate the turn center at a perpendicular distance R from the preceding and following segments. STEP 3: Flight path. Construct an arc of radius R from the tangent point on the preceding course to the tangent point on the following course. STEP 4: Primary area outer boundary. Construct an arc of radius R+Primary area half-width from the tangent point on the preceding segment primary area outer boundary to the tangent point on the following course primary area outer boundary. STEP 5: Secondary area outer boundary. Construct an arc of radius R+Primary area half-width+secondary area width from the tangent point on the preceding segment secondary area outer boundary to the tangent point on the following course secondary area outer boundary. STEP 6: Primary area inner boundary. Construct an arc of radius R-Primary area half-width from the tangent point on the preceding segment inner primary area boundary to the tangent point on the following course inner primary area boundary. STEP 7: Secondary area inner boundary. Construct an arc of radius R-(Primary area half-width+secondary area width) from the tangent point on the preceding segment inner secondary area boundary to the tangent point on the following course inner secondary area boundary.

°

Figure 2-7. RF Turn Construction.

Evaluated as both segments B and C

Evaluated as both segments A and B

Determine Radius (R)

Locate Turn Center

SEGMENT A

SEGMENT B

STEP 1

STEP 2

SEGMENT C

R

R

STEP 6

STEP 7

STEP 4

STEP 3

STEP 5

STEP 5

2.6 Descent Gradient. The optimum descent gradient in the initial segment is 250 ft/NM (4.11%, 2.356°); maximum is 500 ft/NM (8.23%, 4.70°). For high altitude penetrations, the optimum is 800 ft/NM (13.17%, 7.5°); maximum is 1,000 ft/NM (16.46%, 9.35°). The optimum descent gradient in the intermediate segment is 150 ft/NM (2.47%, 1.41°); maximum is 318 ft/NM (5.23%, 3.0°).

2.6.1 Calculating Descent Gradient (DG). Determine total altitude lost between the plotted positions of the fixes. Determine the distance (D) in NM. Divide the total altitude lost by D to determine the segment descent gradient (see figure 2-8 and formula 2-10).

Figure 2-8. Calculating Descent Gradient.

FIX

FIX

1,500

( ) b

2,900

( ) a

5.14 ( ) D

Formula 2-10. Descent Gradient.

r a r ln r b DG D

+ ⎛ ⎞ ⋅ ⎜ ⎟ + ⎝ ⎠ =

where a = beginning altitude b = ending altitude D = distance (NM) between fixes r = 20890537

(r*ln((r+a)/(r+b)))/D

Calculator

a

b

D

DG

Click Here

to Calculate

2.7 Feeder Segment. When the initial approach fix (IAF) is not part of the en route structure, it may be necessary to designate feeder routes from the en route structure to the IAF. The feeder segment may contain a sequence of TF segments (and/or RF segments). The maximum course change between TF segments is 70 degrees above FL190, and 90 degrees (70 degrees preferred) below FL190. Formula 2-3c Notes 1 and 2 apply. Paragraph 2.5 turn construction applies. The feeder segment terminates at the IAF (see figures 2-9a and 2-9b). 2.7.1 Length. The minimum length of a sub-segment is determined under paragraph 2.5.1b or 2.5.2a as appropriate. The maximum length of a sub-segment is 500 miles. The total length of the feeder segment should be as short as operationally possible. 2.7.2 Width. Primary area width is ± 4.0 NM from course centerline; secondary area width is 2.0 NM (2-4-4-2). These widths apply from the feeder segment initial fix to the approach IAF/termination fix. Where the initial fix is on an airway, chapter 2 construction applies. Note: These criteria also support STARs. STARs beginning ≤ 30 NM from ARP width is ± 2.0 NM from course centerline; secondary area width is 1.0 NM (1-2-2-1).

Figure 2-9a. Feeder route (fly-by protection).

See paragraph 2.5 for turn construction details

Figure 2-9b. Feeder Route (Fly-over Protection).

See paragraph 2.5 for turn construction details

2.7.3 Obstacle Clearance.

The minimum ROC over areas not designated as mountainous under Federal Aviation Regulation (FAR) 95 is 1,000 ft. The minimum ROC within areas designated in FAR 95 as “mountainous” is 2,000 ft. TERPS paragraphs 1720 b(1), b(2) and 1721 apply. The published minimum feeder route altitude must provide at least the minimum ROC value and must not be less than the altitude established at the IAF.

2.7.4 Descent Gradient. (feeder, initial, intermediate segments) The optimum descent gradient in the feeder and initial segments is 250 ft/NM (4.11%, 2.356°); maximum is 500 ft/NM (8.23%, 4.70°). For high altitude penetrations, the optimum is 800 ft/NM (13.17%, 7.5°); maximum is 1,000 ft/NM (16.46%, 9.35°). The optimum descent gradient in the intermediate segment is 150 ft/NM (2.47%, 1.41°); maximum is 318 ft/NM (5.23%, 3.0°).

Chapter 2. General Criteria › Section 2. Terminal Segments

Chapter 2. General Criteria

Section 2. Terminal Segments 2.8 Initial Segment. The initial segment begins at the IAF and ends at the intermediate fix (IF). The initial segment may contain sequences of straight sub segments (see figure 2-10). Paragraphs 2.8.2, 2.8.3, 2.8.4, and 2.8.5 apply to all sub segments individually. The total length of all sub segments must not exceed 50 NM. For descent gradient limits, see paragraph 2.7.4.

Figure 2-10. Initial Sub Segments.

IAF Sub Segment

Sub Segment

IF

FAF

Initial Segment

2.8.1 Course Reversal. The optimum design incorporates the basic Y or T configuration. This design eliminates the need for a specific course reversal pattern. Where the optimum design cannot be used and a course reversal is required, establish a holding pattern at the initial or intermediate approach fix. See paragraph 2.8.6b. The maximum course change at the fix (IAF/IF) is to 90 degrees (70 degrees above FL 190).

2.8.2 Alignment. Design initial/initial and initial/intermediate TF segment intersections with the smallest amount of course change that is necessary for the procedure. No course change is optimum. Where a course change is necessary, it should normally be limited to 70 degrees or less; 30 degrees or less is preferred. The maximum allowable course change between TF segments is 90 degrees.

2.8.3 Area – Length. The maximum segment length (total of sub segments) is 50 NM. Minimum length of sub segments is determined as described in paragraphs 2.5.1b and 2.5.2a. 2.8.4 Area – Width (see table 2-2). 2.8.5 Obstacle Clearance. Apply 1,000 ft of ROC over the highest obstacle in the primary OEA. The ROC in the secondary area is 500 ft at the primary boundary tapering uniformly to zero at the outer edge (see figure 2-11).

Figure 2-11. Initial Segment ROC.

1000’ 500’ 500’

P P S S

Calculate the secondary ROC values using formula 2-11a.

Formula 2-11a. Secondary ROC.

sec ondary

d ROC 500 1 D ⎛ ⎞ = ⋅ − ⎜ ⎟ ⎝ ⎠ where D = width (ft) of secondary

d = distance (ft) from edge of primary area measured perpendicular to boundary

500*(1-d/D)

Calculator

d

D

ROCsecondary

Click Here

to Calculate

2.8.6 Holding Pattern Initial Segment. A holding pattern may be incorporated into the initial segment procedure design where an operational benefit can be derived; e.g., arrival holding at an IAF, course reversal pattern at the IF, etc. See FAA Order 7130.3, Holding Pattern Criteria, for RNAV holding pattern construction guidance. 2.8.6 a. Arrival Holding. Ideally, the holding pattern inbound course should be aligned with the subsequent TF leg segment (tangent to course at the initial fix of the subsequent RF segment). See figure 2-12a. If the pattern is offset from the subsequent TF segment course, the subsequent segment length must accommodate the resulting DTA requirement. Maximum offset is 90 degrees (70 degrees above FL190). Establish the minimum holding altitude at or above the IAF/IF (as appropriate) minimum altitude. MEA minimum altitude may be lower than the minimum holding altitude.

Figure 2-12a. Arrival Holding Example.

2.8.6 b. Course Reversal. Ideally, establish the minimum holding altitude as the minimum IF fix altitude (see figure 2-12b). In any case, the published holding altitude must result in a suitable descent gradient in the intermediate segment: optimum is 150 ft/NM (2.47%, 1.41°); maximum is 318 ft/NM (5.23%, 3.0°). If the pattern is offset from the subsequent TF segment course, the subsequent segment length must accommodate the resulting DTA requirement. Maximum offset is 90 degrees.

Figure 2-12b. Course Reversal Example.

2.9 Intermediate Segment. The intermediate segment primary and secondary boundary lines connect abeam the plotted position of the PFAF at the appropriate primary and secondary final segment beginning widths. 2.9.1 Alignment (Maximum Course Change at the PFAF).

• LPV & LNAV/VNAV. Align the intermediate course within 15 degrees of the final approach course (15 degrees maximum course change). • LNAV & LP. Align the intermediate course within 30 degrees of the final approach course (30 degrees maximum course change). Note: For RNAV transition to ILS final, no course change is allowed at the PFAF. 2.9.2 Length (Fix to Fix). The minimum category (CAT) A/B segment length is 3 NM; the optimum is 3 NM. The minimum CAT C/D segment length is 4 NM; the optimum is 5 NM, where turns over 45 degrees are required, the minimum is 6 NM. The minimum CAT E segment length is 6 NM. Where turns to and from the intermediate segment are necessary, determine minimum segment length using formula 2-6 or 2-7 as appropriate. 2.9.3 Width. The intermediate segment primary area tapers uniformly from ± 2 NM at a point 2 NM prior to the PFAF to the outer boundary of the X OCS abeam the PFAF (1 NM past the PFAF for LNAV and LNAV/VNAV). The secondary boundary tapers uniformly from 1 NM at a point 2 NM prior to the PFAF to the outer boundary of the Y OCS abeam the PFAF (1 NM past the PFAF for LNAV and LNAV/VNAV). See figures 2-13a and 2-13b.

Policy Memo Oct 02 2009

Figure 2-13a. RNAV Intermediate

Segment (LPV, ILS, LP).

PFAF

“X” OCS

“X” OCS

“Y” OCS

IF “W” OCS

2 NM

1 NM

1 NM

2 NM

2 NM

Evaluated as both

segments A & B

Segment B

Segment A

Figure 2-13b. RNAV Intermediate Segment

(LNAV and LNAV/VNAV).

1 NM

0.30 NM

IF

0.30 NM

0.60 NM

0.60 NM

2 NM

2 NM

1 NM

2 NM

Evaluated as both

segments A & B

Segment B

Segment A

1 NM

PFAF

Evaluated as final segment from early PFAF ATT to late MAP ATT

If a turn is designed at the IF, it is possible for the inside turn construction to generate boundaries outside the normal segment width at the taper beginning point 2 miles prior to the PFAF. Where these cases occur, the inside (turn side) boundaries are a simple straight line connection from the point 1 NM past the PFAF on the

final segment, to the tangent point on the turning boundary arc as illustrated in figures 2-13c and 2-13d.

Figure 2-13c. LNAV, LNAV/VNAV Example.

Figure 2-13d. LP, LPV Example.

2.9.3 a. LNAV/VNAV, LNAV Offset Construction. Where LNAV intermediate course is not an extension of the final course, use the following construction (see figure 2-13e). STEP 1: Construct line A perpendicular to the intermediate course 2 NM prior the PFAF. STEP 2: Construct line B perpendicular to the intermediate course extended 1 NM past the PFAF. STEP 3: Construct the inside turn boundaries by connecting the points of intersection of line A with the turn side intermediate segment boundaries with the intersection of line B with the turn side final segment boundaries. STEP 4: Construct arcs centered on the PFAF of 1 NM and 1.3 NM radius on the non-turn side of the fix. STEP 5: Connect lines from the point of intersection of line A and the outside primary and secondary intermediate segment boundaries to tangent points on the arcs constructed in step 4. STEP 6: Connect lines tangent to the arcs created in step 4 that taper inward at 30 degrees relative to the FAC to intersect the primary and secondary final segment boundaries as appropriate. The final segment evaluation extends to a point ATT prior to the angle bisector. The intermediate segment evaluation extends ATT past the angle bisector. Therefore, the area within ATT of the angle bisector is evaluated for both the final and intermediate segments.

Figure 2-13e. Offset LNAV Construction.

SEGMENT A

SEGMENT B

Evaluated as both segments A and B

0.30 NM

STEP 3

STEP 4 STEP 6

STEP 5

STEP 2

A

B

B

A

0.30 NM

0.60 NM

0.60 NM

1 NM

IF

2 NM

2 NM

1 NM

30°

PFAF

1 NM 2 NM

Bisector

Offset LNAV/VNAV Construction.

0.30 NM

STEP 1

STEP 3

STEP 4

STEP 6

STEP 5

STEP 2

A

B

B

SEGMENT A

SEGMENT B

A

0.30 NM

0.60 NM

0.60 NM

1 NM

IF

2 NM

2 NM

1 NM

2 NM

15°

1 NM

PFAF

Evaluated as both segments A and B

Angle Bisector

2.9.3 b. LPV, LP Offset Construction. Where LP intermediate course is not an extension of the final course, use the following construction (see figure 2-13f). STEP 1: Construct line A perpendicular to the intermediate course 2 NM prior the PFAF. STEP 2: Construct line B perpendicular to the intermediate course extended 1 NM past the PFAF. STEP 3: Construct the inside turn boundaries by connecting the points of intersection of line A with the turn side intermediate segment boundaries with the intersection of line B with the turn side final segment boundaries. STEP 4: Connect lines from the point of intersection of line A and the outside primary and secondary intermediate segment boundaries to the final segment primary and secondary final segment lines at a point perpendicular to the final course at the PFAF. The final segment evaluation extends to a point ATT prior to the angle bisector. The intermediate segment evaluation extends ATT past the angle bisector. Therefore, the area within ATT of the angle bisector is evaluated for both the final and intermediate segments.

Figure 2-13f. Offset LP Construction.

A

B

B

A

PFAF

STEP 1

Bisector

STEP 2

STEP 3

STEP 4

1 NM

IF

2 NM

2 NM

1 NM

1 NM

30°

Evaluated as both segments A and B

2 NM

Offset LPV Construction.

B

Evaluated as both segments A and B

A

PFAF

SEGMENT A

SEGMENT B

STEP 1

STEP 2

STEP 3

STEP 4

1 NM

IF

2 NM

2 NM

1 NM

1 NM

“X” OCS

“X” OCS

“Y” OCS

“W” OCS

15°

2 NM

A

B

Bisector

2.9.3 c. RF intermediate segments. Locate the intermediate leg’s RF segment’s terminating fix at least 2 NM outside the PFAF. 2.9.4 Obstacle Clearance. Apply 500 ft of ROC over the highest obstacle in the primary OEA. The ROC in the secondary area is 500 ft at the primary boundary tapering uniformly to zero at the outer edge (see figure 2-14).

Figure 2-14. Intermediate Segment ROC.

S S P

500’

P

ROC adjustment if required

Calculate the secondary ROC values using formula 2-11b.

Formula 2-11b. Secondary ROC.

( )

primary sec ondary

S

d ROC 500 adj 1 W

⎛ ⎞ = + ⋅ − ⎜ ⎟ ⎝ ⎠

where dprimary = perpendicular distance (ft) from edge of primary area

WS = Width of the secondary area adj = TERPS para 323 adjustments

(500+adj)*(1-dprimary/WS)

Calculator

dprimary

WS

adj

ROCsecondary

Click Here

to Calculate

2.9.5 Minimum IF to LTP Distance. (Applicable for LPV and LP procedures with no turn at PFAF) Locate the IF at least dIF (NM) from the LTP (see formula 2-12).

Formula 2-12. Min IF Distance.

IF

d 0.3048 d 0.3 d a 1852 = ⋅ − ⋅

where d = distance (ft) from FPAP to LTP/FTP a = width (ft) of azimuth signal at LTP (table 2-7, column 5 value)

0.3*d/a-d*0.3048/1852

Calculator

a

d

dIF

Click Here

to

Calculate

Policy Memo Sep 16 2009

Chapter 2. General Criteria › Section 3. Basical Vertically Guided Final Segment

Chapter 2. General Criteria

Section 3. Basic Vertically Guided

Final Segment General Criteria 2.10 Authorized Glidepath Angles (GPAs). The optimum (design standard) glidepath angle is 3 degrees. GPAs greater than 3 degrees that conform to table 2-4 are authorized without Flight Standards/ military authority approval only when obstacles prevent use of 3 degrees. Flight Standards approval is required for angles less than 3 degrees or for angles greater than the minimum angle required for obstacle clearance. Note: USAF only – apply guidance per AFI 11-230.

Table 2-4. Maximum Allowable GPAs*.

Category θ

A** 5.7

B 4.2

C 3.6

D&E 3.1

* LPV: Where HATh < 250, Cat A-C Max 3.5 degrees, Cat D/E Max 3.1 degrees. ** Cat A 6.4 degrees if VKIAS limited to 80 knots maximum. Apply the TERPS, Volume 1, chapter 3 minimum HATh values based on glidepath angle where they are higher than the values in this order.

2.11 Threshold Crossing Height (TCH). Select the appropriate TCH from table 2-5. Publish a note indicating VGSI not coincident with the procedures designed descent angle (VDA or GPA, as appropriate) when the VGSI angle differs by more than 0.2 degrees or when the VGSI TCH is more than 3 ft from the designed TCH.

Note: If an ILS is published to the same runway as the RNAV procedure, it’s TCH and glidepath angle values should be used in the RNAV procedure design. The VGSI TCH/angle should be used (if within table 4-5 tolerances) where a vertically guided procedure does not serve the runway.

Policy Memo Dec 29 2011

Table 2-5. TCH Requirements.

Representative

Aircraft Type

Approximate Glidepath-to- Wheel Height

Recommended

TCH ± 5 Ft Remarks

HEIGHT GROUP 1 General Aviation, Small Commuters, Corporate

turbojets: T-37, T-38, C-12, C-20,

C-21, T-1, T-3, T-6,

UC-35, Fighter Jets

10 ft or less 40 ft

Many runways less than 6,000 ft long with reduced widths and/or

restricted weight bearing which would normally prohibit landings

by larger aircraft.

HEIGHT GROUP 2 F-28, CV-340/440/580, B- 737, C-9, DC-9, C-130, T- 43, B-2, S-3

15 ft 45 ft Regional airport with limited air

carrier service.

HEIGHT GROUP 3 B-727/707/720/757, B-52, C-17, C-32, C-135,

C-141, E-3, P-3, E-8

20 ft 50 ft

Primary runways not normally

used by aircraft with ILS glidepath-to-wheel heights

exceeding 20 ft.

HEIGHT GROUP 4 B-747/767/777, L-1011,

DC-10, A-300, B-1, KC-10, E-4,

C-5, VC-25

25 ft 55 ft Most primary runways at major

airports.

Notes: 1: To determine the minimum allowable TCH, add 20 ft to the glidepath-to-wheel height.

2: To determine the maximum allowable TCH, add 50 ft to the glidepath-to-wheel height.

3: Maximum LPV TCH is 60 ft.

2.12 Determining FPAP Coordinates (LPV and LP only). The positional relationship between the LTP and the FPAP determines the final approach ground track. Geodetically calculate the latitude and longitude of the FPAP using the LTP as a starting point, the desired final approach course (optimum course is the runway bearing) as a forward true azimuth value, and an appropriate distance (see formulas 2-13, 2-14, and 2-15). Apply table 2-7 to determine the appropriate distance from LTP to FPAP, signal splay, and course width at LTP.

Table 2-6. FPAP Location.

1 2 3 4 5

ILS Serves Runway ILS Does Not Serve Runway

LTP Dist to LOC FPAP Dist from

LTP

FPAP Dist from

LTP

± Slay ± Width Offset Length

≤ 10,023' ≤

9,023' 9023 2.0° ** Formula 2-15

**

> 10,023' and ≤

13,366' Formula 2-13*

**

350 ft (106.75 m)*

**

> 13,366 and ≤

17,185'

to DER

> 17,185' (AFS

or Appropriate Military Agency

Approval)

to DER or as

specified by

approving

agency

9023

1.5° ** Formula 2-14*

**

0 **

* Round result to the nearest 0.25 meter. ** Use the ILS database values if applying column 1.

Formula 2-13. Signal Splay.

length

350 180 splay a tan RWY 1000

⎛ ⎞ = ⋅ ⎜ ⎟ ⎜ ⎟ + π ⎝ ⎠

atan(350/(RWYlength+1000))*180/π

Calculator

RWYlength

splay

Click Here

to Calculate

Formula 2-14. Width at LTP.

( ) length width tan 1.5 RWY 1000 0.3048 180 π ⎛ ⎞ = ⋅ ⋅ + ⋅ ⎜ ⎟ ⎝ ⎠

Round result to the nearest 0.25 meters

tan(1.5*π/180)*(RWYlength+1000)*0.3048

Calculator

RWYlength

width

Click Here

to Calculate

Formula 2-15. Offset Length.

length dis tance length offset FPAP RWY = −

FPAPDistance-RWYlength

Calculator

FPAPdistance

RWYlength

offsetlength

Click Here

to Calculate 2.13 Determining Precise Final Approach Fix/Final Approach Fix (PFAF/FAF) Coordinates (see figure 2-15).

Figure 2-15. Determining PFAF Distance to LTP.

Curved Line BaroVNAV

Straight Line ILS

ILS PFAF Calculation Baro VNAV PFAF

Calculation

Curved Line BaroVNAV

coded θ

Intermediate

Segment M

inimum Altitude

DPFAF form

ula 2-16a

DPFAF form

ula 2-16b

Geodetically calculate the latitude and longitude of the PFAF using the true bearing from the landing threshold point (LTP) to the PFAF and the horizontal distance (DPFAF) from the LTP to the point the glidepath intercepts the intermediate segment altitude. The ILS/LPV glidepath is assumed to be a straight line in space. The LNAV/VNAV (BaroVNAV) glidepath is a curved line (logarithmic spiral) in space. The calculation of PFAF distance from the LTP for a straight line is different than the calculation for a curved line. Therefore, two formulas are provided for determining this distance. Formula 2-16a calculates the glide slope intercept point (GPIP, ILS nomenclature; PFAF, LPV nomenclature) distance from LTP; i.e., the point that the straight line glide slope intersects the minimum intermediate segment altitude.) Formula 2-16b calculates the LNAV/VNAV PFAF distance from LTP; i.e., the point that the curved line BaroVNAV based glidepath intersects the minimum intermediate segment altitude. If LNAV/VNAV minimums are published on the chart, use formula 2-16b. If no LNAV/VNAV line of minima is published on the approach chart, use formula 2-16a, (DGPIP = DPFAF). Note: Where an RNAV LNAV/VNAV procedure is published to an ILS runway, and the ILS PFAF must be used, publish the actual LNAV/VNAV glidepath angle (θBVNAV) calculated using formula 2-16c.

Formula 2-16a. ILS GPIP/LPV PFAF.

( ) elev

GPIP

cos r LTP TCH 180 D r asin 2 180 r alt

⎛ ⎞ ⎛ ⎞ π ⎛ ⎞ θ ⋅ ⋅ + + ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ π π ⎝ ⎠ ⎜ ⎟ ⎜ ⎟ = ⋅ −θ ⋅ − ⎜ ⎟ ⎜ ⎟ + ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ ⎝ ⎠

where alt = minimum intermediate segment altitude LTPelev = LTP MSL elevation TCH = TCH value r = 20890537 θ = glidepath angle

r*(π/2-θ*π/180-asin((cos(θ*π/180)*(r+LTPelev+TCH))/(r+alt)))

Calculator

LTPelev

θ

TCH

alt

DGPIP

Click Here

to Calculate

°

Formula 2-16b. LNAV/VNAV PFAF.

elev PFAF

r alt ln r r LTP TCH D

tan 180

⎛ ⎞ + ⋅ ⎜ ⎟ + + ⎝ ⎠ = π ⎛ ⎞ θ ⋅ ⎜ ⎟ ⎝ ⎠ where alt = minimum intermediate segment altitude LTPelev = LTP MSL elevation TCH = TCH value r = 20890537 θ = glidepath angle

(ln((r+alt)/(r+LTPelev+TCH))*r)/tan(θ*π/180)

Calculator

LTPelev

TCH

θ

alt

DPFAF

Click Here

to Calculate

Formula 2-16c. VNAV/VNAV Angle.

alt BVNAV

elev PFAF

r PFAF r 180 a tan ln r LTP TCH D

⎛ ⎞ ⎛ ⎞ + θ = ⋅ ⋅ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ + + π ⎝ ⎠ ⎝ ⎠

where LTPelev = LTP MSL elevation PFAFalt = Minimum MSL altitude at PFAF DPFAF = value from formula 2-14A or distance of existing PFAF TCH = TCH value r = 20890537

atan(ln((r+PFAFalt)/(r+LTPelev+TCH))*r/DPFAF)*180/π

Calculator

PFAFalt

LTPelev

TCH

DPFAF

θBVNAV

Click Here

to Calculate

Policy Memo Sep 16 2009

°

2.14 Determining Glidepath Altitude at a Fix. Calculate the altitude (Zglidepath) of the glidepath at any distance (DZ) from the LTP using formula 2-17a for ILS and LPV, and formula 2-17b for LNAV/VNAV.

Formula 2-17a. ILS/LPV.

( ) elev

glidepath

Z

r LTP TCH cos 180 Z r D cos r 180

π ⎛ ⎞ + + ⋅ θ ⋅ ⎜ ⎟ ⎝ ⎠ = − π ⎛ ⎞ + θ ⋅ ⎜ ⎟ ⎝ ⎠

where LTPelev = LTP MSL elevation TCH = TCH value θ = glidepath angle r = 20890537 DZ = distance (ft) from LTP to fix

((r+LTPelev+TCH)*cos(θ*π/180))/cos(DZ/r+θ*π/180)-r

Calculator

LTPelev

TCH

θ

DZ

Zglidepath

Click Here

to Calculate

Formula 2-17b. LNAV/VNAV.

( )

Z D tan 180 r glidepath elev Z e r LTP TCH r

π ⎛ ⎞ ⋅ θ⋅ ⎜ ⎟ ⎝ ⎠ = ⋅ + + − where LTPelev = LTP MSL elevation TCH = TCH value θ = glidepath angle r = 20890537 DZ = distance (ft) from LTP to fix

e^((DZ*tan(θ*π/180))/r)*(r+LTPelev+TCH)-r

Calculator

LTPelev

TCH

θ

DZ

Zglidepath

Click Here

to Calculate

°

°

2.15 Common Fixes. Design all procedures published on the same chart to use the same sequence of charted fixes. 2.16 Clear Areas and Obstacle Free Zones (OFZ). Airports Division is responsible for maintaining obstruction requirements in AC 150/5300-13, Airport Design. Appropriate military directives apply at military installations. For the purpose of this order, there are two OFZs that apply: the runway OFZ and the inner approach OFZ. The runway OFZ parallels the length of the runway and extends 200 ft beyond the runway threshold. The inner OFZ overlies the approach light system from a point 200 ft from the threshold to a point 200 ft beyond the last approach light. If approach lights are not installed or not planned, the inner OFZ does not apply. When obstacles penetrate either the runway or inner OFZ, visibility credit for lights is not authorized, and the lowest ceiling and visibility values are (USAF/USN NA): • For GPA ≤ 4.2°: 300-¾ (RVR 4000) • For GPA > 4.2°: 400-1 (RVR 5000) 2.17 Glidepath Qualification Surface (GQS). The GQS extends from the runway threshold along the runway centerline extended to the DA point. It limits the height of obstructions between DA and runway threshold (RWT). When obstructions exceed the height of the GQS, an approach procedure with positive vertical guidance (ILS, MLS, TLS, LPV, Baro-VNAV, etc.) is not authorized.* *Note: Where obstructions penetrate the GQS, vertically guided approach operations may be possible with aircraft groups restricted by wheel height. Contact the FAA Flight Procedure Standards Branch, AFS-420, (or appropriate military equivalent) for case-by-case analysis.

2.17.1 Area. 2.17.1 a. Origin and Length. The GQS extends from the origin to the DA. The OCS origin is dependent on the TCH value (see figures 2-16a, b, and c).

• If the TCH > 50, the GQS originates at z feet above LTP elevation (see formula 2-18a).

Formula 2-18a. OCS Origin height adjustment.

= − offset V TCH 50

TCH-50

Calculator

TCH

Voffset

Click Here to Calculate

• If the TCH ≥ 40 and ≤ 50, the GQS originates at RWT at LTP elevation.

• If the TCH < 40, the GQS originates x feet from (toward PFAF) RWT at LTP elevation. See formula 2-18b.

Formula 2-18b. OCS Origin along-track adjustment.

− = π ⎛ ⎞ θ ⋅ ⎜ ⎟ ⎝ ⎠

offset

40 TCH X

tan 180

Where θ = glide slope angle TCH = threshold crossing height

(40-TCH)/tan(θ*π/180)

Calculator

TCH

θ

Xoffset

Click Here to Calculate

Where Xoffset > 200 ft, the area between the end of the POFZ (see paragraph 2.18) and the GQS origin is Rwy Width 100 2 ' ± + wide, centered on the runway

centerline extended. Obstacles higher than the clearway plane (see paragraph 2.17.1e) that are not fixed by function for instrument landing operations are not allowed in this area.

°

Figure 2-16a. GQS Origin.

Xoffset

Voffset

GQS (TCH > 50)

GQS (TCH < 40)

GQS (TCH 40 and 50) ≥ ≤

Glidepath

d

ZBaro/ILS TCH

2.17.1 b. Width. The GQS originates 100 ft from the runway edge at RWT.

Figure 2-16b. GQS (TCH ≥ 40).

Figure 2-16c. GQS (TCH < 40).

W E

d

100’

100’

D

GQS

x

Calculate the GQS half-width E at the DA point measured along the runway centerline extended using formula 2-18c:

Formula 2-18c. Half Width.

E 0.036 D 392.8 = ⋅ + where D = distance (ft) measured along RCL extended from LTP to DA point

0.0036*D+392.8

Calculator

D

E

Click Here

to Calculate

Calculate the half-width of the GQS at any distance d from RWT using the formula 2-19:

Formula 2-19. GQS Half-width.

E k w d k D

− = ⋅ +

where D = distance (ft) measured along RCL extended from

LTP to DA point E = Result of formula 2-18c d = desired distance (ft) from LTP

w = GQS half-width at distance "d"

width RWY k 100 2 = +

d*(E-k)/D+k

Calculator

E

D

d

RWYwidth

w

Click Here

to Calculate

2.17.1 c. If the course is offset from the runway centerline, expand the GQS area on the side of the offset as follows referring to figures 2-17 and 2-18: STEP 1: Construct line BC. Locate point B on the runway centerline extended perpendicular to course at the DA point. Calculate the half-width (E) of the GQS for the distance from point B to the RWT. Locate point C perpendicular to the course distance E from the course line. Connect points B and C. STEP 2: Construct line CD. Locate point D 100 ft from the edge of the runway perpendicular to the LTP. Draw a line connecting point C to point D. STEP 3: Construct line DF. Locate point F 100 ft from the edge of the runway perpendicular to the LTP. Draw a line connecting point D to point F. STEP 4: Construct line AF. Locate point A distance E from point B perpendicular to the runway centerline extended. Connect point A to point F. STEP 5: Construct line AB. Connect point A to point B.

Figure 2-17. Example: TCH ≥ 40 ft.

D STEP 3 LINE DF

STEP 2 LINE CD

STEP 4 LINE AF

STEP 1 LINE BC

C

B

DA

A

GQS

FINAL APPROACH

COURSE

F

E

E

RWY

Figure 2-18. Example: TCH < 40 ft.

D STEP 3 LINE DF

STEP 2 LINE CD

STEP 4 LINE AF

STEP 1 LINE BC

C

B

DA

A

GQS

FINAL APPROACH

COURSE

F

E

E

D

F

X

Calculate the half-width of the offset side of the GQS trapezoid using formula 2-20.

Formula 2-20. Offset Side Half-width.

( )

( )

offset

cos sin D i E k 180 180 w d k D sin sin D i E 180 180

⎛ ⎞ ⎛ ⎞ π π ⎛ ⎞ ⎛ ⎞ φ ⋅ ⋅ φ ⋅ ⋅ − + − ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠ ⎜ ⎟ = ⋅ + ⎜ ⎟ ⎛ ⎞ π π ⎛ ⎞ ⎛ ⎞ − φ ⋅ ⋅ φ ⋅ ⋅ − + ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠ where d = distance (ft) from LTP to point in question D = distance (ft) along RCL from LTP to point B i = distance (ft) from LTP to RWY centerline intersection φ = degree of offset E = 0.036D+392.8

width RWY k 100 2 = +

DA LTP W

RWY

FINAL APPROACH

COURSE

i

d

D

B

d*((cos(φ*π/180)*(sin(φ*π/180)*(D-i)+E)-k)/(D-sin(φ*π/180)*(sin(φ*π/180)*(D-i)+E)))+k

Calculator

d

D

i

φ

E

RWYwidth

woffset

Click Here to

Calculate °

2.17.1 d. OCS. The GQS vertical characteristics reflect the glidepath characteristics of the procedure; i.e., the ILS/MLS/TLS/LPV based glidepath is a straight line in space, and the Baro-VNAV based glidepath (LNAV/VNAV, RNP) is a curved line in space. Obstructions must not penetrate the GQS. Calculate the MSL height of the GQS at any distance “d” measured from runway threshold (RWT) along runway centerline (RCL) extended to a point abeam the obstruction using the applicable version of formula 2-21.

Formula 2-21. GQS Elevation.

( ) θ π ⎛ ⎞ + + ⋅ ⎜ ⎟ ⎝ ⎠ = − − θ π ⎛ ⎞ + ⋅ ⎜ ⎟ ⎝ ⎠

elev offset

GQS

offset

2 r LTP V cos 3 180 Z r d X 2 cos r 3 180

Where d = obstacle along RCL distance (ft) from RWT LTPelev = LTP MSL elevation θ = Glidepath angle Voffset = see formula 2-18a Xoffset = see formula 2-18b

(r+LTPelev+Voffset)*cos((2*θ/3)*π/180)/cos((d-Xoffset)/r+(2*θ/3)*π/180)-r

( )

( )

offset

2 d X tan 3 180 r Baro elev offset Z e r LTP V r

θ π ⎛ ⎞ − ⋅ ⋅ ⎜ ⎟ ⎝ ⎠ = ⋅ + + −

Where d = obstacle along RCL distance (ft) from RWT LTPelev = LTP MSL elevation θ = Glidepath angle Voffset = see formula 2-18a Xoffset = see formula 2-18b lev = LTP MSL elevation

e^((d-Xoffset)*tan((2*θ/3)*π/180)/r)*(r+LTPelev+Voffset)-r

Calculator

LTPelev

Xoffset

Voffset

d

θ

ZGQS

ZBaro

Click Here

to Calculate

°

2.17.1 e. Terrain under the clearway plane (1st 1,000 ft off the approach end of the runway) is allowed to rise at a slope of 80:1 (grade of 1.25%) or appropriate military equivalent (see figure 2-19). Terrain and obstacles under the 80:1 slope (grade of 1.25 percent) are not considered obstructions; i.e., for the first 1,000 ft of the GQS, only obstacles that penetrate the clearway plane are evaluated.

Figure 2-19. Allowable GQS Penetrations.

2.18 Precision Obstacle Free Zone (POFZ). (Effective when reported ceiling is less than 300 ft and/or visibility less than ¾ statute miles (SM) while an aircraft on a verticallyguided approach is within 2 NM of the threshold.) The tail and/or fuselage of a taxiing aircraft must not penetrate the POFZ when an aircraft flying a vertically guided approach (ILS, MLS, LPV, TLS, RNP, LNAV/ VNAV, PAR) reaches 2 NM from threshold. The wing of aircraft holding on a perpendicular taxiway waiting for runway clearance may penetrate the POFZ; however, the fuselage or tail must not infringe the area. The minimum authorized HATh and visibility for the approach is 250 ft and ¾ SM where the POFZ is not clear (see figure 2-20).

Figure 2-20. POFZ.

Chapter 2. General Criteria › Section 4. Missed Approach General Information

Chapter 2. General Criteria

Section 4. Missed Approach General Information 2.19 Missed Approach Segment (MAS) Conventions. Figure 2-21 defines the MAP point OEA construction line terminology and convention for section 1.

Figure 2-21. MAS Point/Line Identification.

Line CD begins, Line AB ends Section 1 Line EF ends MAP ATT (if used) Line GH ends distance to accommodate pilot reaction time Line JK marks SOC, ends Section 1A Line PP’ indicates the late turn point (if used) Line P’P” may be used when required Line LL’ indicates the early turn point (if used) Line L’L’’ may be used when required

Line C-E-G-J-L-A-P

Turn Side Points

Default and Left Turn

Right Turn

MAP

SOC

C

D

E

F

G

H

J

K

L

L’

A

B

P

P’

Section 1A

Section 1B (LPV Only)

MAP

SOC

D

C

F

E

H

G

K

J

L’

L

B

A

P’

P”

P”

P

Section 1A

Section 1B (LPV Only)

2-61 (and 2-62)

The missed approach obstacle clearance standard is based on a minimum aircraft climb gradient of 200 ft/NM, protected by a ROC surface that rises at 152 ft/NM. The MA ROC value is based on a requirement for a 48 ft/NM (200-152 = 48) increase in ROC value from the start-of-climb (SOC) point located at the JK line (AB line for LPV). The actual slope of the MA surface is (1 NM in feet)/152 ≈ 39.974. In manual application of TERPS, the rounded value of 40:1 has traditionally been applied. However, this order is written for automated application; therefore, the full value (to 15 significant digits) is used in calculations. The nominal OCS slope (MAOCSslope) associated with any given missed approach climb gradient is calculated using formula 2-22.

Formula 2-22. Missed Approach OCS Slope.

( ) OCSslope

1852 MA 0.3048 CG 48 = ⋅ −

where CG = Climb Gradient (nominally 200 ft/NM)

1852/(0.3048*(CG-48))

Calculator

CG

MAOCSslope

Click Here to Calculate 2.19.1 Charted Missed Approach Altitude. Apply TERPS Volume 1, paragraphs 277d and 277f to establish the preliminary and charted missed approach altitudes. 2.19.2 Climb-In-Holding. Apply TERPS Volume 1, paragraph 277e for climb-in-holding guidance.

Chapter 3. Non-Vertically Guided Procedures 3.0 General. This chapter contains obstacle evaluation criteria for Lateral Navigation (LNAV), and Localizer Performance (LP) non-vertically guided approach procedures. For RNAV transition to Localizer (LOC) final, use LP criteria to evaluate the final and missed approach when RNAV is used for missed approach navigation. When constructing a “stand-alone” non-vertically guided procedure, locate the PFAF using formula 2-16b, nominally based on a 3-degree vertical path angle. The PFAF location for circling procedures that do not meet straight-in alignment are based on the position of the MAP instead of the LTP (substitute Airport elevation + 50 for LTP elevation + TCH). 3.1 Alignment. Optimum non-vertically guided procedure final segment alignment is with the runway centerline extended through the LTP. When published in conjunction with a vertically guided procedure, alignment must be identical with the vertically guided final segment.

Order 8260.54A › Chapter 3. Non-Vertically Guided Procedures

3.1.1 When the final course must be offset, it may be offset up to 30 degrees (published separately) when the following conditions are met: 3.1.1 a. For offset ≤ 5 degrees, align the course through LTP. 3.1.1 b. For offset > 5 degrees and ≤ 10 degrees, the course must cross the runway centerline extended at least 1,500 ft prior to LTP (5,200 ft maximum). 3.1.1 c. For offset > 10 degrees and ≤ 20 degrees, the course must cross the runway centerline extended at least 3,000 ft prior to LTP (5,200 ft maximum). (Offsets >15 degrees, Category C/D minimum published visibility 1 SM, minimum HATh of 300) 3.1.1 d. For offset > 20 to 30 degrees (Cat A/B only), the course must cross the runway centerline extended at least 4,500 ft prior to the LTP (5,200 ft maximum). Note: Where a-d above cannot be attained or the final course does not intersect the runway centerline or intersects the centerline more than 5,200 ft from LTP, and an operational advantage can be achieved, the final may be aligned to lie laterally within 500 ft of the extended runway centerline at a point 3,000 ft outward from LTP.

This option requires Flight Standards approval.

3.1.2 Circling. The OPTIMUM final course alignment is to the center of the landing area, but may be to any portion of the usable landing surface. The latest point the MAP can be located is abeam the nearest usable landing surface. 3.2 Area - LNAV Final Segment. The intermediate segment primary and secondary areas taper from initial segment OEA width (1-2-2-1) to the width of the final segment OEA. The taper begins at a point 2 NM prior to the PFAF and ends 1.0 NM past the PFAF. The final segment OEA primary and secondary areas follow the tapering boundaries of the intermediate segment from ATT prior to the PFAF to the point 1 NM past the PFAF, and then are a constant width to 0.3 NM past the MAP. See figure 3-1.

Figure 3-1. LNAV Final Segment OEA.

0.3 NM

0.3 NM

0.3 NM

0.6 NM

0.6 NM 1.0 NM

PFAF LTP/FTP

0.3 NM

3.2.1 Length. The OEA begins 0.3 NM prior to the PFAF and ends 0.3 NM past the LTP. Segment length is the distance from the PFAF location to the LTP/FTP location. Determine the PFAF location per paragraph 2.13. The maximum length is 10 NM. 3.2.2 Width. The final segment OEA primary and secondary boundaries are coincident with the intermediate segment boundaries (see paragraph 2.9) from a point 0.3 NM prior to the PFAF to a point 1 NM past the PFAF. See formula 3-1. From this point, the Primary OEA boundary is ± 0.6 NM (≈ 3,646 ft) from course centerline. A 0.3 NM (≈ 1,823 ft) secondary area is

Formula 3-1. Tapering Segment Width.

1 2 1.4d wp 0.6 3 0.7d ws 0.3 3

= +

= +

where d = along-track distance from line “B”

½wp = 1.4*d/3+0.6

ws = 0.7*d/3+0.3

Calculator

d

½wp

ws

Click Here

to Calculate

3.3 Area – LP Final Segment. The intermediate segment primary and secondary areas taper from initial segment OEA width (1-2-2-1) to the width of the final segment OEA. The taper begins at a point 2 NM prior to the PFAF and ends abeam the PFAF. The final segment OEA primary and secondary areas are linear (constant width) at distances greater than 50,200 ft from LTP. Inside this point, they taper uniformly until reaching a distance of 200 ft from LTP. From this point the area is linear to the OEA end 131.23 ft (40 m) past the LTP. See figure 3-2.

Figure 3-2. LP Final Area.

700’

700’ PRIMARY AREA

PFAF

LTP or FTP

300’

300’

200’

40 Meters 131.23 feet 40 Meters 131.23 feet

6076’

6076’ 8576’

8576’

2500’

2500’

50,200 feet

3.3.1 Length. The OEA begins 131.23 ft (40 m) prior to the PFAF and ends 131.23 ft (40 m) past the LTP. Segment length is the distance from the PFAF location to the LTP/FTP location. Determine the PFAF location per paragraph 2.13. The maximum length is 10 NM. 3.3.2 Width. (See figure 3-2) The perpendicular distance (Wp) from the course centerline to the outer boundary of the primary area is a constant 700 ft from a point 131.23 ft (40 m) past (inside) the LTP to a point 200 prior to (outside) the LTP. It expands from this point in a direction toward the PFAF. Calculate Wp from the 200 ft point to a point 50,200 from LTP using formula 3-2. The value of Wp beyond the 50,200-ft point is 6,076 ft.

Formula 3-2. Primary Area Width.

P W 0.10752 D 678.5 = ⋅ +

where D = Along-track distance (> 200 ≤ 50,200) from LTP/FTP

0.10752*D+678.5

Calculator

D

WP

Click Here to Calculate

The perpendicular distance (Ws) from the course centerline to the outer boundary of the secondary area is a constant 1,000 ft from a point 40 meters past (inside) the LTP to a point 200 prior to (outside) the LTP. It expands from this point in a direction toward the PFAF. Calculate Ws from the 200 ft point to a point 50,200 from LTP using formula 3-3. The value of Ws beyond the 50,200-ft point is 8,576 ft.

Formula 3-3. Secondary Area Width.

S W 0.15152 D 969.7 = ⋅ +

where D = Along-track distance (> 200 ≤ 50,200) from LTP/FTP

0.15152*D+969.7

Calculator

D

WS

Click Here to Calculate

Policy Memo Sep 16 2009

Policy Memo Sep 16 2009

3.4 Obstacle Clearance. 3.4.1 Primary Area. Apply 250 ft of ROC to the highest obstacle in the primary area. TERPS Volume 1, chapter 3 precipitous terrain, remote altimeter, and excessive length of final adjustments apply. 3.4.2 Secondary Area. Secondary ROC tapers uniformly from 250 ft (plus adjustments) at the primary area boundary to zero at the outer edge. See figure 3-3.

Figure 3-3. Primary/Secondary ROC.

S S P

250’

P

ROC adjustment if required

Calculate the secondary ROC value using formula 3-4.

Formula 3-4. Secondary Area ROC.

( )

primary sec ondary

S

d ROC 250 adj 1 W

⎛ ⎞ = + ⋅ − ⎜ ⎟ ⎝ ⎠

where dprimary = perpendicular (relative to course centerline)

distance (ft) from edge of primary area WS = Width of the secondary area (s) adj = TERPS para 323 adjustments

(250+adj)*(1-dprimary/WS)

Calculator

dprimary

WS

adj

ROCsecondary

Click Here to Calculate

3.5 Final Segment Stepdown Fixes (SDF). Where the MDA can be lowered at least 60 ft or a reduction in visibility can be achieved, SDFs may be established in the final approach segment.

3.5.1 TERPS, Volume 1, paragraph 289 applies, with the following: 3.5.1 a. Establish step-down fix locations in 0.10 NM increments from the LTP/FTP. 3.5.1 b. The minimum distance between stepdown fixes is 1 NM. 3.5.1 c. For step-down fixes published in conjunction with vertically-guided minimums, the published altitude at the fix must be equal to or less than the computed glidepath altitude at the fix. Note: Glidepath altitude is calculated using the formula associated with the basis of the PFAF calculation. 3.5.1 d. The altitude at any stepdown fix may be established in 20 ft increments and shall be rounded to the next HIGHER 20-ft increment. For example, 2104 becomes 2120. 3.5.1 e. Where a RASS adjustment is in use, the published stepdown fix altitude must be established no lower than the altitude required for the greatest amount of adjustment (i.e., the published minimum altitude must incorporate the greatest amount of RASS adjustment required). 3.5.1 f. TERPS, Volume 1, paragraph 252 applies to LNAV and LP descent gradient. Note: Where turns are designed at the PFAF, the 7:1 OIS starts ATT prior to the angle bisector, and extends 1 NM parallel to the final approach centerline. See figure 2-13e (LNAV) and figure 2-13f (LP). 3.5.1 g. Obstacles eliminated from consideration under this paragraph must be noted in the procedure documentation. 3.5.1 h. Use the following formulas to determine OIS elevation (OISZ) at an obstacle and minimum fix altitude (MFa) based on an obstacle height.

Formula 3-5. OIS elevation & Minimum Fix Altitude.

X Z

O OIS a c 7 = − −

X Z

O MFa O c 7 = + +

where c = ROC plus adjustments (TERPS Vol 1, para 3.2.2) a = MSL fix altitude Ox = Obstacle along-track distance (ft) from ATT prior to fix (1 NM max)

Oz = MSL obstacle elevation

Stepdown

Fix

ATT

c

a

OISZ

MFa

OX

1 NM

Flight Direction

Mean Sea Level

OZ

OISZ=a-c-OX/7 MFa=OZ+c+OX/7

Calculator

a

c

OX (1 NM Max)

OZ

OISZ

MFa

Click Here

to Calculate

3.6 Minimum Descent Altitude (MDA). The MDA value is the sum of the controlling obstacle elevation MSL (including vertical error value when necessary) and the ROC + adjustments. Round the sum to the next higher 20-ft increment; e.g., 623 rounds to 640. The minimum HATh value is 250 ft. 3.7 Missed Approach Section 1. (MAS-1). Section 1 begins ATT prior to the MAP and extends to the start-of-climb (SOC) or the point where the aircraft is projected to cross 400 ft above airport elevation, whichever is the greatest distance from MAP. See figure 3-4. 3.7.1 Length. 3.7.1 a. Flat Surface Length (FSL). 3.7.1 a. (1) LNAV. Section 1 flat surface begins at the cd line (0.3 NM prior to the MAP) and extends (distance FSL feet) to the jk line. 3.7.1 a. (2) LP. Section 1 flat surface begins at the cd line (40 meters prior to the MAP) and extends (distance FSL feet) to the jk line. Calculate the value of FSL using formula 3-6. 3.7.1 b. Location of end of section 1 (ab line). 3.7.1 b. (1) MDA ≥ 400 ft above airport elevation. The ab line is coincident with the jk line.

3.7.1 b. (2) MDA < 400. The ab line is located ( )

1852 0.3048 CG ⋅ feet beyond the

jk line for each foot of altitude needed to reach 400 ft above airport elevation. The surface between the jk and ab lines is a rising surface with a slope commensurate with the rate of climb (nominally 40:1).

Formula 3-6. Flat Surface Length.

( )

( ) KIAS 2.628 171233 288 15 0.00198 MDA FSL 20.2537 V 10 2 ATT 288 0.00198 MDA

⎛ ⎞ ⎛ ⎞ ⋅ + − ⋅ ⎜ ⎟ ⎜ ⎟ = ⋅ ⋅ + + ⋅ ⎜ ⎟ ⎜ ⎟ − ⋅ ⎝ ⎠ ⎝ ⎠

20.2537*((VKIAS*(171233*((288+15)-0.00198*MDA)^0.5)/(288-0.00198*MDA)^2.628)+10)+2*ATT

Calculator

VKIAS

ATT

MDA

FSL

Click Here to Calculate

3.7.2 Width. LNAV and LP. 3.7.2 a. LNAV. The primary area boundary splays uniformly outward from the edge of the primary area at the cd line until it reaches a point 2 NM from course centerline. The secondary area outer boundary lines splay outward 15 degrees relative to the missed approach course from the outer edge of the secondary areas at the cd line (0.3 NM prior to MAP) until it reaches a point 3 NM from course centerline. Calculate the distance from course centerline to the primary and outer secondary boundary of the MAS-1 OEA at any distance from the cd line using formula 3-7a.

Formula 3-7a. LNAV Primary & Secondary Width.

Yprimary

Y sec ondary

tan 15 1.4 NM 180 MAS d 0.6 NM 2.1 NM

MAS d tan 15 0.9 NM 180

π ⎛ ⎞ ⋅ ⋅ ⋅ ⎜ ⎟ ⎝ ⎠ = ⋅ + ⋅ ⋅

π ⎛ ⎞ = ⋅ ⋅ + ⋅ ⎜ ⎟ ⎝ ⎠

where d = along-track distance (ft) from the cd line ≤ 47620.380 NM = 1852/0.3048

MASYprimary=d*((tan(15*π/180)*1.4*1852/0.3048))/(2.1*1852/0.3048)+0.6*1852/0.3048

MASYsecondary=d*tan(15*π/180)+0.9*1852/0.3048

Calculator

d

LNAV MASYprimary

LNAV MASYsecondary

Click Here to Calculate

Continue reading ↓ 120 of 542 passages shown