Order 8130.2L Airworthiness Certification of Aircraft
This order establishes policies and procedures for issuing airworthiness certificates, export certificates of airworthiness, and special flight authorizations for aircraft. This order applies to Federal Aviation Administration (FAA) aviation safety inspectors and certain persons designated to act as representatives of the FAA.
This document is cancelled. Cancelled by 8130.2M. Check the official source before relying on it.
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
ORDER
8130.2L
National Policy
SUBJ: Airworthiness Certification of Aircraft
This order establishes policies and procedures for issuing airworthiness certificates, export certificates of airworthiness, and special flight authorizations for aircraft. This order applies to Federal Aviation Administration (FAA) aviation safety inspectors and certain persons designated to act as representatives of the FAA.
If this order is utilized by persons other than the FAA or the Administrator’s designees, it is a guidance document. Its content is not legally binding in its own right and will not be relied upon by the Department as a separate basis for affirmative enforcement action or other administrative penalties. Conformity with the guidance document is voluntary only. Nonconformity will not affect rights and obligations under existing statutes and regulations.
Daniel J. Elgas Director, Policy and Standards Division Aircraft Certification Service
Distribution: Electronic Initiated By: AIR-632
01/30/2026
JAMES DAVID FOLTZ
Digitally signed by JAMES DAVID FOLTZ Date: 2026.01.30 15:23:47 -06'00'
Table of Contents
Paragraph Page
Table of Contents … ii
List of Tables … ix
List of Figures … x
Chapter 1. Introduction … 1-1
1-1. Purpose of This Order … 1-1
1-2. Audience … 1-1
1-3. Where Can I Find This Order? … 1-1
Table of Contents
1-4. Showing and Finding … 1-1
1-5. Aircraft Located Outside the United States … 1-1
1-6. Cross Utilization … 1-1
1-7. Explanation of Policy Changes … 1-2
1-8. Cancellation … 1-3
1-9. FAA Forms … 1-4
1-10. Acronyms, Definitions, and Related Publications … 1-4
1-11. Conflicts … 1-4
1-12. Effective Date … 1-4
Chapter 2. Common Policies and Procedures for Issuing an Airworthiness Certificate … 2-1
2-1. Introduction … 2-1
2-2. Persons Authorized to Issue an Airworthiness Certificate … 2-1
2-3. Common Procedures for Issuing an Airworthiness Certificate … 2-2
2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers … 2-9
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) … 3-1
3-1. Introduction … 3-1
3-2. Common Requirements for Reviewing Aircraft Records … 3-1
3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)) … 3-1
3-4. New Aircraft Manufactured Under a TC Only (§ 21.183(b)) … 3-2
3-5. New Import Aircraft, Foreign SOM (§ 21.183(c)) … 3-2
3-6. Used Aircraft (§ 21.183(d)) … 3-2
3-7. Manned Free Balloons … 3-3
ii
Chapter 4. Issuing Special Airworthiness Certificates … 4-1
Section 1. General … 4-1
4-1. Introduction … 4-1
4-2. Common Procedures for Issuing a Special Airworthiness Certificate … 4-2
4-3. Flight Operations Outside the United States … 4-2
4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores … 4-2
Section 2. Experimental Airworthiness Certificates … 4-3
4-5. Introduction … 4-3
4-6. Common Procedures for Issuing an Experimental Airworthiness Certificate (§ 21.191) … 4-3
4-7. Flight Test Areas … 4-4
4-8. Multipurpose Experimental Airworthiness Certificates … 4-6
4-9. PC Holder’s or Modifier’s Procedure for Operating Experimental Aircraft … 4-7
4-10. Former-Military Aircraft Operated for Experimental Purposes … 4-8
4-11. Flight Operations in Reduced Vertical Separation Minimum (RVSM) Airspace. 4-11
4-12. Pioneer Era Aircraft … 4-11
Chapter 5. Primary Category (§ 21.184) … 5-1
5-1. Introduction … 5-1
5-2. General Requirements … 5-1
5-3. New Aircraft Manufactured Under a PC (§ 21.184(a)) … 5-1
5-4. New Imported Aircraft (§ 21.184(b)) … 5-1
5-5. Aircraft Having a Current Standard Airworthiness Certificate (§ 21.184(c)) … 5-1
5-6. Other Aircraft (§ 21.184(d)) … 5-2
Chapter 6. Restricted Category (§ 21.185) … 6-1
6-1. Introduction … 6-1
6-2. Common Requirements … 6-1
6-3. New Aircraft Manufactured as Restricted Category (§ 21.185(a)) … 6-1
6-4. Aircraft Previously TC’d in Another Category (§ 21.185(b)) … 6-2
6-5. Recurrent Certificates for Restricted Category Aircraft (§ 21.185(a) or (b)) … 6-2
6-6. Import Aircraft (§ 21.185(c)) … 6-2
iii
Chapter 7. Issue of Multiple Airworthiness Certifications for Restricted Category Aircraft (§ 21.187) … 7-1
7-1. Introduction … 7-1
7-2. Procedures for Issuing Multiple Airworthiness Certificates for an Aircraft … 7-1
Chapter 8. Limited Category (§ 21.189) … 8-1
8-1. Introduction … 8-1
8-2. Procedures for Issuing an Airworthiness Certificate … 8-1
Chapter 9. Light-Sport Category Aircraft (§ 21.190) … 9-1
9-1. Introduction … 9-1
9-2. General … 9-1
9-3. Procedures for Issuing an Airworthiness Certificate … 9-2
9-4. Changing From Experimental Purpose to Light-Sport Category … 9-6
Chapter 10. Experimental Purposes of R&D and Showing Compliance § 21.191(a) and (b))10-1
10-1. Introduction … 10-1
10-2. Procedures for Issuing an Airworthiness Certificate … 10-1
10-3. Holding an Airworthiness Certificate in Suspension … 10-1
Chapter 11. Experimental Purpose of Crew Training (§ 21.191(c)) … 11-1
11-1. Introduction … 11-1
11-2. Procedures for Issuing an Airworthiness Certificate … 11-1
Chapter 12. Experimental Purpose of Exhibition (§ 21.191(d)) … 12-1
12-1. Introduction … 12-1
12-2. Procedures for Issuing Airworthiness Certificates … 12-1
Chapter 13. Experimental Purpose of Air Racing (§ 21.191(e)) … 13-1
13-1. Introduction … 13-1
13-2. Procedures for Issuing Airworthiness Certificates … 13-1
Chapter 14. Experimental Purposes of Market Surveys, Sales Demonstrations, and Customer Crew Training (§§ 21.191(f) and 21.195) … 14-1
14-1. Introduction … 14-1
14-2. Procedures for Issuing an Airworthiness Certificate … 14-1
14-3. Reducing Flight Hour Requirements of § 21.195(d)(2) … 14-1
iv
Chapter 15. Experimental Purpose of Operating Amateur-Built Aircraft (§ 21.191(g)) … 15-1
15-1. Introduction … 15-1
15-2. General … 15-1
15-3. When Builders or Applicants Contact the FAA … 15-2
15-4. Procedures for Issuing an Airworthiness Certificate … 15-2
Chapter 16. Experimental Purpose for Primary Kit-Built Aircraft (§ 21.191(h)) … 16-1
16-1. Introduction … 16-1
16-2. Procedures for Issuing an Airworthiness Certificate … 16-1
Chapter 17 Experimental Purpose of Operating Light-Sport Aircraft, Operating Light-Sport
Category Kit-Built Aircraft, and Operating Former Light-Sport Category Aircraft (§ 21.191(i), (k), and (l)) … 17-1
17-1. Introduction … 17-1
17-2. General … 17-1
17-3. Procedures for Issuing an Airworthiness Certificate … 17-2
Chapter 18 Special Flight Permits (§ 21.197) … 18-1
Section 1. Common Policies and Procedures … 18-1
18-1. Introduction … 18-1
18-2. Who May Issue a Special Flight Permit (SFP)? … 18-1
18-3. Purposes … 18-2
18-4. Procedures … 18-2
Section 2. Additional Policies and Procedures for Particular Purposes … 18-6
18-5. Production Flight Testing of Aircraft Produced under a TC/PC … 18-6
18-6. Production Flight Testing LSA … 18-7
18-7. Conducting Customer Demonstration Flights … 18-8
18-8. Operation of Overweight Aircraft … 18-9
18-9. Aircraft to Which § 91.409(e) Is Applicable … 18-12
Chapter 19.Provisional Airworthiness Certificates (14 CFR Part 21, Subpart I) … 19-1
19-1. Introduction … 19-1
19-2. Procedures for Issuing an Airworthiness Certificate … 19-1
Chapter 20. Import Aircraft … 20-1
20-1. Introduction … 20-1
v
20-2. CAA Assistance with U.S. Airworthiness Certificates for New Aircraft Manufactured Outside the United States … 20-1
20-3. Export Certificate of Airworthiness (Export C of A) … 20-1
20-4. Procedures for Issuing an Airworthiness Certificate … 20-3
20-5. Aircraft with Mandatory Continuing Airworthiness Information (MCAI) … 20-6
Chapter 21. Issuing an Export Certificate of Airworthiness (§ 21.329) … 21-1
21-1. Introduction … 21-1
21-2. Issuance of Export Certificates of Airworthiness § 21.329 … 21-1
21-3. Unassembled Aircraft … 21-4
21-4. Approval of Alterations … 21-5
21-5. Multiple Categories … 21-5
21-6. Replacement and Correction of FAA Form 8130-4 … 21-5
Chapter 22. Special Flight Authorizations for Foreign Civil Aircraft (§ 91.715) … 22-1
22-1. Introduction … 22-1
22-2. Eligibility … 22-1
22-3. Procedures … 22-2
Chapter 23. Other Policies and Procedures … 23-1
23-1. Introduction … 23-1
23-2. Public Aircraft Operations (PAO) … 23-1
23-3. Production Flight Testing of Aircraft Built Under Military Contract … 23-1
23-4. Operation of Civil Aircraft with a Door Open or Removed Parachuting, Skydiving, or Other Special Operations … 23-1
23-5. Replacement ID Plates … 23-2
23-6. New Aircraft Manufactured Under § 21.6(b) … 23-3
Section 3. Military Surplus Flight Safety Critical Aircraft Parts, Engines, & Propellers … 23-3
23-7. Evaluation … 23-3
23-8. Dual Use FSCAP (New or Used) … 23-4
Chapter 24. Administrative Information … 24-1
24-1. Distribution … 24-1
24-2. Authority to Change This Order … 24-1
24-3. Deviations … 24-1
24-4. Suggestions for Improvements … 24-1
vi
24-5. Records Management … 24-1
Appendix A. Completing and Reviewing FAA Forms … A-1
Section 1. General Procedures … A-1
A-1. General … A-1
Section 2. Application for U.S. Airworthiness Certificate … A-2
A-2. Completion of FAA Form 8130-6, Application for U.S. Airworthiness Certificate.A-2
Section 3. Standard Airworthiness Certificate … A-4
A-3. Completion of FAA Form 8100-2, Standard Airworthiness Certificate … A-4
Section 4. Special Airworthiness Certificate … A-7
A-4. Completion of FAA Form 8130-7, Special Airworthiness Certificate … A-7
Section 5. Light-Sport Aircraft Statement of Compliance … A-14
A-5. Reviewing FAA Form 8130-15, Light-Sport Aircraft Statement of Compliance…...A-14
Section 6. Application for Export Certificate of Airworthiness … A-24
A-6. Reviewing FAA Form 8130-1, Application for Export C of A … A-24
Section 7. Export Certificate of Airworthiness … A-25
A-7. Completion of FAA Form 8130-4, Export Certificate of Airworthiness … A-25
Appendix B. Documents for Review and Forwarding … B-1
B-1. Introduction … B-1
B-2. Airworthiness Certification Files … B-1
B-3. Review Certification Files … B-1
B-4. Forward Certification Files to AFB-710 … B-2
Appendix C. Program Letters … C-1
C-1. General … C-1
C-2. Program Letter Content … C-1
C-3. Aircraft That Could Perform Public or Military Aircraft Operations … C-4
Appendix D. Issuing Operating Limitations with Special Airworthiness Certificates … D-1
D-1. Introduction … D-1
D-2. General … D-1
D-3. Phased Operating Limitations … D-2
vii
D-4. Procedures for Creating Operating Limitations … D-2
D-5. Requests to Add, Modify, or Omit a Limitation, and Required Coordination … D-6
D-6. Review with Applicant … D-7
Appendix E. CAA Assistance with U.S. Airworthiness Certificates for New
Aircraft Manufactured Outside the United States … E-1
E-1. Introduction … E-1
E-2. Applicability … E-1
E-3. Procedure … E-1
Appendix F. Sample Special Flight Authorizations … F-1
Appendix G. Limitations for Operation of an Aircraft with a Door Removed … G-1
Appendix H. Acronyms … H-1
Appendix I. Definitions … I-1
Appendix J. Related Publications … J-1
Appendix K. FAA Form 1320-19, Directive Feedback Information … K-1
viii
List of Tables
List of Tables
Table Page
Table 1-1. Summary of Airworthiness Regulations, Policies, and Procedures … 1-5
Table 1-2. FAA Forms Completed by the FAA Under This Order … 1-6
Table 8-1. Limited Category TCs … 8-2
Table B-1. Standard Airworthiness Certificates: Documents for Review and Forwarding to the Registry … B-3
Table B-2. Special Airworthiness Certificates: Documents for Review and Forwarding to the Registry … B-5
Table D-1. Operating Limitations … D-8
ix
List of Figures
List of Figures
Figure Page
Figure 2-1. Common Steps for Issuing an Airworthiness Certificate … 2-12
Figure A-1. Sample FAA Form 8100-2, Standard Airworthiness Certificate … A-6
Figure A-2. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Restricted Category Aircraft … A-9
Figure A-3. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Research and Development … A-10
Figure A-4. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Special Flight Permit for Production Flight Test and Customer Demonstration … A-11
Figure A-5. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Light- Sport Category Aircraft Certificated Under § 21.190 … A-12
Figure A-6. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Experimental LSA Certificated Under § 21.191(k) and (l) … A-13
Figure A-7. Reserved
Figure A-8. Reserved
Figure A-9. Sample FAA Form 8130-4, Export Certificate of Airworthiness … A-30
Figure C-1. Sample R&D/Exhibition/PAO Applicant Program Letter for a Special Airworthiness Certificate … C-5
Figure F-1. Sample SFA for the Flight of an Aircraft to a Place Where Repairs or Alterations Are to Be Made … F-1
Figure F-2. Sample SFA for the Flight of an Aircraft to a New SOR (This Format Is Generally Applicable to a Single Aircraft Authorization for Ferry Flights) … F-3
Figure F-3. Sample SFA for the Purpose of Flight Testing … F-5
Figure F-4. Sample Blanket SFA for Customer Crew Training … F-7
Figure F-5. Sample SFA for Export Delivery … F-9
Figure F-6. Sample Blanket SFA for Delivering Aircraft for the Purpose of Export Delivery … F-11
Figure F-7. Sample SFA for the Purpose of Demonstration … F-12
Figure F-8. Sample SFA for Participating in Aviation Events … F-14
Figure G-1. Sample Limitations for Operation of an Aircraft with a Door Removed … G-1
x
Chapter 1. Introduction › 1-6. Cross Utilization.
Chapter 1. Introduction
1-1. Purpose of This Order. As summarized in Table 1-1 of this chapter, this order establishes policies and procedures for issuing:
a. FAA Form 8100-2, Standard Airworthiness Certificate,
b. FAA Form 8130-7, Special Airworthiness Certificate,
c. Special flight authorizations (SFA), and
d. FAA Form 8130-4, Export Certificate of Airworthiness (export C of A)
This order is used with FAA Order 8130.34, Airworthiness Certification of Unmanned Aircraft Systems and Optionally Piloted Aircraft.
1-2. Audience. FAA manufacturing and airworthiness aviation safety inspectors (ASI) and certain persons designated to act as representatives of the FAA. Airworthiness ASIs must also refer to FAA Order 8900.1, Flight Standards Information Management System, for related policies and procedures.
1-3. Where Can I Find This Order? This order is available on the FAA employee website, the FAA public website, and the FAA Dynamic Regulatory System (DRS).
1-4. Showing and Finding. In seeking a certificate or an authorization under this order, an applicant is responsible for presenting evidence necessary to show compliance with applicable requirements; that is, the burden of proof is on the applicant. The FAA is responsible for reviewing and inspecting the applicant’s evidence to make findings of compliance with applicable requirements. If an applicant’s evidence is insufficient to enable the FAA to make its findings, reviews, and inspections may be stopped until the applicant presents new evidence to support the FAA’s findings.
1-5. Aircraft Located Outside the United States. Except for issuing an airworthiness certificate under paragraph 20-2 of this order, before processing an application for a certificate under this order for an aircraft located outside the United States, the issuing office must find that the activity can be accomplished without placing an undue burden on FAA resources. Using designees to issue a certificate under this order for an aircraft located outside the United States, would not constitute an undue burden on the FAA but must be authorized in accordance with FAA Order 8000.95, Designee Management Policy.
1-6. Cross Utilization. The FAA performs a variety of functions in issuing certificates and authorization under this order. Many of these functions should be accomplished via coordination among manufacturing, airworthiness, or operations ASIs with expertise in particular subject matters. Consult with other ASIs as necessary.
Chapter 1. Introduction › 1-7. Explanation of Policy Changes.
1-7. Explanation of Policy Changes. Incorporates changes resulting from the Modernization of Special Airworthiness Certification (MOSAIC) final rule that are applicable to the rule’s first effective date (October 22, 2025) and changes resulting from agency and departmental memos on agency guidance. The following changes are included in this revision.
a. This revision incorporates memos issued to FAA Order 8130.2K and minor changes.
b. Table of Contents, Chapter 7 title, and Appendix D-4. d. (3); revised description to align with § 21.187. 21.191(k) and (l) were added to section D-4.d.(6).
c. Table of Contents, Chapter 17 title; revised description to align with § 21.191(i), (k) and (l).
d. Table of Contents, Section 5, A-5 and removed Figure A-7 and A-8 examples.
e. Table 1-1; added § 21.191(k) and § 21.191(l) to the table.
f. Paragraph 2-3 d., Note 2; corrected memo number.
g. Paragraph 2-3 f. (1)(d); removed “light-sport” marking requirement per § 45.23 change.
h. Paragraph 2-3 f. (2)(a); revised language to match § 21.182.
i. Chapter 2 and Appendix A; instructions for new blocks added to FAA Form 8130-6.
j. Paragraph 3-6 a; last inspection within 30 days changed to 60 days.
k. Paragraph 4-6 c.; added “issue airworthiness certificate” unintentionally deleted.
l. Chapter 4; removed operations inspector review of flight test areas for experimental aircraft.
m. Chapter 9; revised to align with the MOSAIC rule as of October 22, 2025.
n. Paragraphs 14-3 a. and 21-4; changed “Modified and Modification” to “Altered or Alteration” to align with § 21.195.
o. Chapter 17; added that the FAA will no longer issue airworthiness certificates under § 21.191(i), except for replacements. Incorporated § 21.191(k) and (l). Added that experimental aircraft are subject to the requirements of § 91.319.
p. Paragraph 20-1; corrected introduction language error.
q. Paragraph 20-4 b. (2); added the “(v)” to the reference § 21.183(d)(2)(v).
r. Paragraph 21-2; added rule language that an owner of a U.S.-registered aircraft or the owner's agent may apply.
Chapter 1. Introduction › 1-8. Cancellation.
s. Paragraph A-1 b., A-7 a. (3); corrected conflicting statements to allow “strikeovers” on export documents.
t. Paragraphs A-2 a. (3) and B-3; Allow the special flight permit (SFP) file review to be completed by the same ASI who issued the certificate.
u. Paragraph A-2 b. (12); removed Item M.
v. Paragraph A-4 g.; revised certain experimental airworthiness certificates' expiry from one to three years.
w. Paragraphs A-6 and A-7; removed “Export Certificate no.” (E-card) instructions and re-alphabetized sub-paragraphs.
x. Figure A-7 and A-8; removed samples from the order. Table 1-2 identifies where to download the most current forms.
y. Paragraphs A-7 h., D-4. k.; Allow digital signatures.
z. Paragraph B-4; allows the reviewing office to email the required airworthiness certification files to AFB-710 when airworthiness certification application (AWC) is unavailable. Allows the reviewing office to complete the review no later than 14 calendar days after AWC assigns it to the reviewing office.
aa. Table B-1; added “if applicable” to the FAA-approved flight checkoff form.
bb. Table B-2, page B-6; added “including applicable attachments” to the “copy of operating limitations” line.
cc. Table D-1; operating limitations 7, 17, 26, 39, 41, 42, 43, 44, 48, 49, and 52 modified.
dd. Appendix I, consensus standard: Removed the definition of a consensus standard to
allow FAA-accepted documents that may not be described as a consensus standard.
ee. Appendix I, purpose: Added “aerial delivery” to the list of examples for restricted category aircraft per § 21.181.
ff. Appendix J; removed reference Order 1370.121 and canceled AC 45-4.
gg. Changed “experimental certificate” to “experimental airworthiness certificate” throughout the order.
1-8. Cancellation. The following are canceled upon the effective date of this order:
a. FAA Order 8130.2K, Airworthiness Certification of Aircraft, dated August 28, 2024.
b. All clarification, deviation, and policy memorandums issued for Order 8130.2 before the effective date of this order.
Chapter 1. Introduction › 1-12. Effective Date.
1-9. FAA Forms. Table 1-2 of this chapter lists forms the FAA completes under this order.
1-10. Acronyms, Definitions, and Related Publications. A list of acronyms and definitions is provided in the appendices; see Appendix H and Appendix I, respectively. Additionally, this order references several publications; unless otherwise stated, always refer to the latest revision. See related publications listed in Appendix J
1-11. Conflicts. If a conflict exists between this order and an applicable bilateral agreement, follow the bilateral agreement.
1-12. Effective Date. This order is effective January 30, 2026.
Table 1-1. Summary of Airworthiness Regulations, Policies, and Procedures
14 Code of Federal Regulations (CFR) Part Airworthiness Certificate Classification / Aircraft Category
Design Standard
Design Approval
Production
Approval
Airworthiness
Certificate
Policy
Standard Airworthiness Certificates for: Normal Utility Acrobatic Commuter Transport Manned free balloons Special classes Airplanes with turbine
engines
23, 27 23 23 23 25, 29 31 21.17(b) 34
TC per 21.21/29 PC per 21/G 21.183(a): new under 21/G 21.183(b): new under 21/F 21.183(c): new import, foreign SOM 21.183(d): used & surplus military
Chapter 3
Special Airworthiness Certificates for: Primary Restricted Multiple (Restricted & Limited Light-sport SFP (US-registered) Provisional Experimental purpose of:
- R&D - Showing compliance - Crew training - Exhibition - Air racing - Market surveys - Amateur-built - Primary kit-built - Light-sport - Light-sport kit-built - Former light-sport
21.17(f) Varies Varies DOD ASTM N/A Varies
N/A
21.24/29 TC 21.25/29 Varies TC N/A N/A TC per 21/C
N/A
PC per 21/G Varies Varies N/A N/A N/A PC per 21/G
N/A
21.184 21.185 21.187 21.189 21.190 21.197/199 Part 21/subpart I
21.191/3 21.191(a) 21.191(b) 21.191(c) 21.191(d) 21.191(e) 21.191(f)/195 21.191(g) 21.191(h) 21.191(i) 21.191(k) 21.191(l)
Chapter 4
Chapter 5 Chapter 6 Chapter 7 Chapter 8 Chapter 9 Chapter 18 Chapter 19
N/A Chapter 10 Chapter 10 Chapter 11 Chapter 12 Chapter 13 Chapter 14 Chapter 15 Chapter 16 Chapter 17 Chapter 17 Chapter 17 SFA (Foreign-registered) N/A N/A N/A Part 375, 91.715 Chapter 22 Commercial space transportation
N/A N/A N/A N/A 14 CFR Chapter III
Table 1-1. Summary of Airworthiness Regulations, Policies, and Procedures (cont.)
14 CFR Part Out of Scope of This Order Airworthiness Certificate Classification / Aircraft Category
Design Standard
Design Approval
Production
Approval
Airworthiness
Certificate
Policy
UAS Small UAS (<55#) N/A N/A N/A N/A Part 107
Moored balloons, kites, amateur rockets, & unmanned free balloons
N/A N/A N/A N/A Part 101
Ultralight vehicles N/A N/A N/A N/A Part 103 Limited Recreational UAS N/A N/A N/A N/A 49 U.S. Code § 44809
Public aircraft operations N/A N/A N/A N/A FSIMS Vol 3,
Chapter 14 Commercial space transportation
N/A N/A N/A N/A 14 CFR Chapter III
Table 1-2. FAA Forms Completed by the FAA Under This Order
Form Number Title Source
FAA Form 8100-1 Conformity Inspection Record FAA public website
FAA Form 8100-2 Standard Airworthiness Certificate
ASKME Electronic Airworthiness Certification Application (AWC) or FAA employee website for fillable PDF format
FAA Form 8130-1 Application for Export Certificate of Airworthiness AWC or FAA public website
FAA Form 8130-4 Export Certificate of Airworthiness
AWC or FAA employee website for fillable PDF format
FAA Form 8130-6 Application for U.S. Airworthiness Certificate
AWC or FAA public website for fillable PDF format
FAA Form 8130-7 Special Airworthiness Certificate
AWC or FAA employee website for fillable PDF format
FAA Form 8130-10 Surplus Military Aircraft Inspection Record FAA public website
FAA Form 8130-15 Light-Sport Category Aircraft/Kit Statement of Compliance
AWC or FAA employee website for fillable PDF format
Chapter 2. › 2-2. Persons Authorized to Issue an Airworthiness Certificate.
Chapter 2. Common Policies and Procedures for Issuing an Airworthiness
Certificate
2-1. Introduction. This chapter provides common policies and procedures for issuing, amending, exchanging, and replacing standard and special airworthiness certificates. Additional classification-, category-, and purpose-specific procedures for issuing an airworthiness certificate are included in subsequent chapters of this order. This chapter does not apply to the issuance of a SFP except as referenced by chapter 18 of this order.
Note: The procedures for issuing an airworthiness certificate are a combination of the common procedures of this chapter and the applicable classification-, category-, and purpose-specific procedures in subsequent chapters.
2-2. Persons Authorized to Issue an Airworthiness Certificate.
a. ASIs. FAA ASIs are authorized to issue airworthiness certificates.
b. Delegation. The FAA may delegate the issuance of an airworthiness certificate per Title 14 of the Code of Federal Regulations (14 CFR) Part 183 and the applicable designee management order.
c. Original and Recurrent Certifications.
Note: Refer to Appendix I of this order for definitions of original and recurrent certification and definitions of other terms used throughout this order.
(1) Manufacturing ASIs in the Aircraft Certification Service (AIR) are primarily responsible for original certifications, while airworthiness ASIs in Flight Standards Service (FS) are primarily responsible for recurrent certifications. When it is unclear whether a given activity is an original or recurrent certification, the affected offices should coordinate to establish a mutual agreement with the responsible office. Manufacturing and airworthiness ASIs may assist each other by mutual agreement. Manufacturing ASIs issue the first airworthiness certification for the first aircraft which is likely to lead to a new type certificate data sheet (TCDS), new production certificate (PC), or new light-sport category aircraft manufacturer.
(2) If a responsible FS office receives an application for an original certification, that FS office must coordinate with the responsible AIR Certificate Management (CM) section to determine which office will process the application. Similarly, if an AIR CM section receives an application for a recurrent certification, the AIR CM section must coordinate with the responsible FS office to determine which office will process the application.
(3) Exceptions to paragraphs 2-2.c (1) and (2) of this chapter:
(a) Any request, original or recurrent, for an experimental airworthiness certificate for operating former light-sport category aircraft, operating light-sport category kitbuilt aircraft, operating light-sport aircraft, research and development (R&D), crew training, exhibition, air racing, market survey, or operating an amateur-built aircraft, or for an aircraft
Chapter 2. › 2-3. Common Procedures for Issuing an Airworthiness Certificate.
issued an SFP, may be handled by an FAA manufacturing or airworthiness ASI without coordination to determine which office will process the application.
(b) Experimental Showing Compliance. Processing an application for an experimental airworthiness certificate for showing compliance with regulations is the primary responsibility of an AIR CM section. In remote areas or under special circumstances, an AIR CM section may request an airworthiness ASI perform these duties if that person has experience in type certification programs of a type and complexity comparable to the certificate requested.
2-3. Common Procedures for Issuing an Airworthiness Certificate. Common procedures for issuing an airworthiness certificate are illustrated in Figure 2-1 of this chapter and specified in this paragraph.
a. The ASKME Airworthiness Certification Application (AWC).
(1) AWC provides an electronic means to process an application for certain certificates and authorizations under this order. ASIs, designees, and organization designation authorization (ODA) unit members must establish an account, process FAA Form 8130-6, and issue standard and special airworthiness certificates, FAA Form 8130-1, and denials using AWC. Unless otherwise stated in this order, all requirements concerning completion of FAA Forms 8130-6 and 8130-1 must be accomplished in AWC. Advisory Circular 21-12, Application for a U.S. Airworthiness Certificate, provides additional information for using AWC for FAA Form 8130-6, and this order provides additional information for filling out the FAA Form 8130- 1.
(2) The use of AWC by applicants is not mandatory but is the preferred method for application submission. If an applicant is unable or elects not to submit the application in AWC, the FAA will upload to AWC the hard copy of the application from the applicant and transcribe the information to AWC. The ASI must include a statement that the application information was entered on behalf of the applicant. When completing the application on the Documentation- Certification page of AWC, enter the following statement in the SIGNATURE block of Section III, OWNER’S CERTIFICATION: “Application information entered on behalf of the applicant by (Name), (Title). Original attached.” In such cases, do not sign the hard copy or the uploaded application from the applicant, but digitally sign appropriate sections of Form 8130-6 generated by AWC. Per paragraph B4 of this order, submit both the application signed by the applicant and the AWC-generated application to the FAA Registry (hereafter referred to as Registry).
(3) Access AWC portals as follows. For ASIs, register on the FAA ASI AWC Internet Portal. For Organization Designation Authorization (ODA) unit members and designees, register on the External ODA/Designee AWC Portal; follow the prompts for “New User Registration.” Contact the AWC Help Desk at [email protected] for help with access problems.
(4) You may only issue airworthiness certificates and operating limitations outside of AWC in the event of AWC, FAA network, or internet outage. In such cases, revert to the paper process (or portable document format (PDF) equivalent (see table 1-2)) to document and capture data, process applications, and issue certificates. Once the outage is repaired, upload
documents you created offline to AWC using the Upload Approval page in AWC and use the comments block to record what you uploaded.
b. Review Application.
(1) A properly completed FAA Form 8130-6, Application for U.S. Airworthiness Certificate, is required to begin the process of issuing an airworthiness certificate. Review FAA Form 8130-6 to verify that the applicant completed the form properly. Refer to FAA AC 21-12 for related guidance as necessary.
(2) Letter of Authorization/Agent Letter. If an agent completed the application, verify that the aircraft's registered owner provided a notarized letter of authorization and that the information in this letter is consistent with the application. A true copy of the notarized letter is acceptable.
Note: Requirements and forms of notarization vary among countries.
(3) Type Certificate Data Sheet (TCDS). For an application for an aircraft in a category that requires a type certificate (TC), review the applicable TCDS or aircraft specification to verify that the aircraft is eligible for issuance of the requested airworthiness certificate by make, model, and serial number (S/N). An aircraft listing maintained by the responsible certification branch may consist of aircraft model and S/Ns of newly manufactured aircraft that are not yet listed on the TCDS. If none of these documents clearly show the eligibility of the applicant’s aircraft by make, model, and S/N, contact the responsible certification branch to verify eligibility.
Note: DRS contains TCDSs and aircraft specifications. Terms for type certificate data have changed over time, including aircraft specifications and TCDS. See the latest version of FAA Order 8110.4, Type Certification, for further information.
c. Review FAA Airworthiness Records on File at the Registry. The requirements in this paragraph also apply to the owner’s information page in AWC.
(1) Current Registration. Access the Registry to verify that the aircraft is currently registered per 14 CFR Part 47.
(a) Except for paragraphs (b) through (d), the aircraft is registered when an inquiry of the Registry shows that the nationality and aircraft’s registration number (or registration mark) (hereafter referred to as the N-number) is “assigned” and the status is “valid” or “valid-asgn to mfr.”
(b) For a new owner of a used aircraft, lag time in processing the application for registration may result in records of ownership within the Registry database that lag actual transfers in ownership from one United States (U.S.) owner to another. In such cases, the prior owner remains the registered owner of record within the Registry’s database, and registration by the current owner may only be verified as part of the aircraft records review under paragraph 2-3.e.
(c) For a manufacturer temporary N-number, the aircraft is considered registered when an inquiry of the Registry shows that the N-number is “reserved,” and the status is “manufacturer (temp).”
(d) For the assignment of a new special registration number, the aircraft is registered when an inquiry by the Registry shows that the N-number is “assigned”, and the status is “valid” or “pending.”
Note 1: When searching the Registry for antique or replica aircraft displaying nationality and registration marks as provided for under 14 CFR 45.22(b), omit the inserted symbol allowed by § 45.22(b).
Note 2: For a recurrent certification, including previously exported aircraft returning to the United States, you may retrieve permanent aircraft records from the Registry using the aircraft make, model, and S/N. For aircraft that do not have a data plate or S/N, you may retrieve records using the N-number or prior N-number for previously exported aircraft returning to the United States.
(2) Prior Denials. Except for new aircraft, check the Electronic Document Retrieval System (EDRS), the Civil Aviation Registry Electronic Service (CARES), or order a copy of the aircraft record to determine if the FAA previously issued a denial for this aircraft. If previously denied, verify that the reasons for the denial have been corrected, and record the action taken to clear the denial on the FAA Form 8100-1, Conformity Inspection Record.
d. Identify Potential Safety Hazards. Review available information as necessary to familiarize you with the aircraft, aircraft engine, propeller models, and potential safety hazards. For example, review information as applicable and necessary to understand the manufacturer/builder; configuration; installed equipment; novel or unique features, characteristics, or systems; recent customer findings for new aircraft deliveries; recent quality escapes for new aircraft; histories of service difficulties, incidents, and accidents; ownership history of the aircraft; and potential for degradation from long-term storage. Designees should review the designee alert system for any pertinent information.
Note: The National Transportation Safety Board (NTSB) maintains a searchable database of accidents and incidents involving civil aircraft.
Note: For rotorcraft, review guidance on the Congressional mandate for rotorcraft crash-resistant fuel systems. Refer to AIR Memo No. AIR-600-20-600-PM04R1.
e. Review Aircraft Records.
(1) Registration. Review the certificate of aircraft registration to verify that the aircraft is currently registered and that the information on the registration and application matches. The manufacturer’s name may be abbreviated on the application and/or registration. If the registration does not have an expiration date, the registration is not effective. Evidence of aircraft registration may be shown via any of the following [hereafter referred to as registration]:
(a) Aeronautical Center Form 8050-3, Certificate of Aircraft Registration.
(b) Aeronautical Center Form 8050-6, Dealer’s Aircraft Registration Certificate.
(c) Form REGAR-FAX-4, Temporary Certificate of Registration.
(d) Aircraft Registration Application, FAA AC Form 8050-1, under the provisions of- § 47.31(c).
(e) A copy of Assignment of Special Registration Number, AC Form 8050-64, and the current, AC Form 8050-3, Certificate of Aircraft Registration.
(2) Exemptions. For exemptions that the applicant claims to apply to this aircraft, verify that each exemption is included in DRS and applies to this aircraft make, model, and S/N.
(3) Maintenance Records. Verify the following:
(a) The applicant has all maintenance records required by 14 CFR 91.417.
(b) All maintenance required as of the date you inspect the aircraft is complete, including compliance with applicable airworthiness directives (AD) and applicable aircraft and component life limits.
(c) For used, type-certificated aircraft, maintenance, preventive maintenance, and alterations were accomplished per 14 CFR Part 43.
(4) Weight and Balance. Review the aircraft weight and balance report, including center of gravity (CG) limitations, to verify that it reflects the current configuration.
(5) Manuals. Verify that the applicant has applicable manuals and documents. Applicable manuals and documents may include an aircraft flight manual (AFM), equipment list, FAA-accepted Instructions for Continued Airworthiness (ICA), and FAA-accepted maintenance manual(s). Such manuals and documents may not be required for some aircraft certificated under the Civil Air Regulations (CAR).
(6) Flight Testing. Determine if the aircraft has been flight tested, if required, or as necessary to verify condition for safe operation. As necessary, issue a special airworthiness certificate for showing compliance with the airworthiness regulations (14 CFR 21.127, 21.137(e)(1), 21.189(a)(2), 21.185(d), 21.190(c)(7), and 91.319(b)) per the applicable requirements of this order.
f. Inspect Aircraft. Physically inspect the aircraft to verify−
(1) Nationality, Registration, and Special Marks. The nationality and registration marks meet the requirements of §§ 45.21 through 45.31.
(a) Size. When verifying an N-number is the proper size, verify the height of the marks were measured vertically. The font may be slanted, but do not use the length of the slant line to determine the height of the numbers.
Note: If a surface authorized for displaying required marks under § 45.25 is not large enough to display full-size marks, § 45.25 allows for marks as large as practicable to be displayed. Assessing “as large as practicable” requires judgment based on the aircraft make/model. For example, for some strongly contoured surfaces, smaller marks may be more legible and, therefore more practicable than the largest marks that could fit on that surface.
(b) Legibility, Style, Borders, and Shading. The N-number must be legible and written in capital Roman letters without ornamentation. Borders or shading is allowed only if it makes the number more legible. The color of the registration marks must contrast with the background. The N-number must be legible from 500 feet away when viewing it perpendicular to the side of the aircraft during daylight hours.
Note: Section 45.21(b) prohibits a person from placing on any aircraft a design, mark, or symbol that modifies or confuses the N-number. Note that this requirement is very broad and includes any feature that would modify or confuse the N-number. For example, N-number paint type, paint color, font type(s), or background patterns must not modify or confuse the N-number.
(c) Display of Foreign Marks for Exporting New Aircraft. Per § 45.31, a person who manufactures an aircraft in the United States for export delivery may display foreign marks on the aircraft as required by the importing state of registry (SOR) of the aircraft while the aircraft is registered in the United States. The manufacturer may operate the aircraft with foreign marks within the United States for testing, demonstration, or delivery; note that these flights are performed under an SFP because the aircraft is registered in the United States.
(d) Marking of certain aircraft with a special airworthiness certificate. Except for unmanned aircraft, when marks include only the Roman capital letter “N,” and the registration number is displayed on limited, restricted, experimental, or provisionally certificated aircraft, the operator must also display on that aircraft near each entrance to the cabin, cockpit, or pilot station, in letters not less than 2 inches nor more than 6 inches high, the words “limited,” “restricted,” “experimental,” or “provisional,” as applicable. Refer to § 45.23.
Note: Although § 45.23 requires these marks “near each entrance to the cabin, cockpit, or pilot station,” this rule does not specify whether these marks must be inside or outside the aircraft; either is acceptable.
(e) Special Marks for Antique or Replica Aircraft. Section 45.22(b) provides special marks for exhibition and amateur-built aircraft.
(2) Product Marking.
(a) The aircraft is identified as prescribed in § 45.11 except for an SFP or an experimental airworthiness certificate issued for the purposes of research and development, showing compliance with regulations, crew training, exhibition, air racing, and market survey. Each installed aircraft engine, propeller, propeller blade, and propeller hub manufactured under a TC or production certificate (PC) is marked per § 45.11.
(b) Product identification (ID) plates include the information specified in § 45.13 and must meet § 45.11. Verify that the make, model, and serial number (S/N) on the aircraft engine and aircraft propeller product ID plate(s) match the application. Verify that the aircraft make, model, and S/N on the aircraft ID plate match the registration. Note that the builder’s name may be abbreviated on the application and/or registration.
Note 1: For aircraft manufactured outside the United States pursuant to a § 21.29 TC, the TC and PC numbers on the ID plate may reflect the foreign design and production approval numbers. The ID plate information should provide a means to determine the applicable U.S. TC number if the TC number of the state of manufacture (SOM) is used.
Note 2: In some cases, the FAA has granted regulatory exemptions permitting alternate mounting locations of aircraft ID plates for certain aircraft of qualifying air carriers. For any aircraft whose ID plate is mounted in a location other than that required in § 45.11, verify the provisions of a current regulatory exemption for alternate ID plate location cover this.
(c) When an aircraft has been modified to conform to another make/model, verify that the supplemental ID plate contains the information specified in § 45.13. If Aircraft Registration (AFB-710) has not yet issued the new registration with the new model designation, verify that the aircraft make, and the S/N match the application and current registration. If ownership of the aircraft has not changed, an application for aircraft registration reflecting the new model designation, need not be submitted; AFB-710 will change the model and issue a new registration after receipt of the certification files. Verify that the original ID plate has not been altered in any manner.
(d) Inspect the aircraft and review aircraft records to determine whether a violation of §§ 45.13(c) or (e) is apparent. If a violation of §§ 45.13(c) or (e) is found, deny the airworthiness certificate and initiate an enforcement action.
(3) Conformity to TC. For an application for an aircraft in a category that requires a TC, verify that the aircraft conforms to its TC. This includes conformity to applicable ADs, major repairs, and major alterations. Verify that minor repairs or alterations conform to FAAaccepted data.
(4) Engines, Propellers, and Associated Instruments. Engine(s), propeller(s), and associated instruments have been checked per the manufacturer’s instructions or other FAAapproved instructions, placards, or flight manual supplements.
(5) Systems. All aircraft systems, to the extent necessary, including the flight control and pitot-static systems. Aircraft records of inspections may be used to ensure the aircraft has been checked for proper operation.
(6) Equipment. The installed equipment, including all equipment on the aircraft equipment list, has been checked and verified as functioning properly.
(7) Instruments and Placards. Instruments and placards are correctly located, installed, and properly marked in the English language. In addition, verify that measurements are
displayed in standard U.S. units of measure for those instruments necessary for operation in the U.S. national airspace system (NAS).
(8) Airframe Emergency Parachutes. Verify that the aircraft log includes the reinspection date for the parachute and associated deployment system components. As applicable, verify that airframe emergency parachutes that are ballistic, assisted, or deployable are properly marked, identified, and within their service dates. Verify aircraft marks clearly identify all explosive devices used in conjunction with ballistic parachutes; marks indicating the aircraft is equipped with explosive devices must be applied externally and be readable from the ground. Verify that the aircraft log includes the reinspection date for the parachute and associated deployment system components.
(9) Foreign Objects. No foreign objects are present that could pose a safety hazard. For example, foreign objects could include tools, scrap material, or miscellaneous debris.
(10) Airworthiness. The aircraft is airworthy.
g. Document Reviews and Inspections. Document all completed reviews and inspections on FAA Form 8100-1, per the instructions on the form. Verify that the applicant corrects all unsatisfactory findings and document those corrections on FAA Form 8100-1 before issuing an airworthiness certificate.
h. Issue Airworthiness Certificate. If you find the aircraft airworthy and all other requirements are met for the requested certificate:
(1) Complete sections V and VIII of FAA Form 8130-6 per the block-by-block instructions in section 2 of Appendix A to this order.
(2) Complete the standard or special airworthiness certificate, as applicable, per the block-by-block instructions in sections 3 or 4, respectively, of Appendix A to this order. Review the certificate to verify that it was completed without error.
(3) Make a maintenance record entry. The following is a satisfactory statement for the maintenance record entry: “I find that this aircraft meets the requirements for the certificate requested and have issued a [standard airworthiness certificate or special airworthiness certificate for the purpose(s) of (enter purpose) and operating limitations] dated … [Signature: John Smith, Aviation Safety Inspector, AIR-883].”
(4) Give the completed airworthiness certificate to the applicant. Advise the applicant to display it in the aircraft at the cabin or cockpit entrance so it is legible to passengers or flight crew per § 91.203(b).
Note: In certain circumstances, such as replacements and others deemed appropriate by the local office manager, transmitting the certificate by email is permissible.
Chapter 2. › 2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers.
i. Issue Letter of Denial.
(1) If, after notifying the applicant of all unsatisfactory findings, the applicant does not correct those findings to your satisfaction in a timely manner, write a letter to the applicant denying issuance of the certificate and stating the reason(s) for the denial. Identify which steps may be accomplished to meet the certification requirements if feasible.
(2) Complete sections V and VIII of FAA Form 8130-6.
j. Review Records and Forward to the Registry.
(1) Review your records to verify completeness, accuracy, legibility, and compliance with applicable requirements.
(2) Review and forward certification files per Appendix B to this order.
2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers.
a. Amendment.
(1) Eligibility. An airworthiness certificate may be amended when there is—
(a) A change in the aircraft model specified on an airworthiness certificate.
(b) An alteration to the aircraft, such as one approved by a supplemental type certificate (STC) or amended TC, that changes the aircraft category specified in block 4 of the standard airworthiness certificate.
(c) A change in the operating limitations for an aircraft with a special airworthiness certificate.
(2) Procedures for Amending an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.e of this order is not required. Review aircraft records as necessary in consideration of the reason for the amendment.
(b) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.f of this order is not required. Inspect the aircraft as necessary in consideration of the reason for the amendment.
Note: In amending a special airworthiness certificate, all operating limitations must be issued per the current version of this order; Appendix D, Table D-1.
b. Exchange.
(1) Eligibility. Owners that hold an unexpired FAA Form 1362A, Certificate of Airworthiness, FAA Form 1362B, Certificate of Airworthiness, or unexpired Form ACA-1362,
Certificate of Airworthiness, may apply for FAA Form 8100-2, Standard Airworthiness Certificate, or FAA Form 8130-7, Special Airworthiness Certificate, as applicable.
(2) Procedures for Exchanging an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review Application. The existing certificate serves as the application; an FAA Form 8130-6 is not required.
(b) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.e of this order is not required. Review aircraft records as necessary to verify that the applicant’s request is valid.
(c) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.f of this order is not required. Inspect the aircraft per paragraph 2-3.f(1) and 2-3.f(2)(b) to verify that the exterior aircraft N-registration numbers and ID plate information match the application and registration.
c. Replacement.
(1) Eligibility. The FAA may issue a replacement airworthiness certificate when a certificate is declared lost, has been mutilated, is no longer legible, or contains inaccurate and/or erroneous information or when the aircraft registration number has changed. If the “inaccurate and/or erroneous information” was a result of errors induced or not detected by the assigned inspector (or designee) within 6 months of the most recently submitted airworthiness file, the inspector (or designee) should make the necessary corrections and resubmit the certification file to the Registry. If the “inaccurate and/or erroneous information” was detected within 6 months of the most recently submitted airworthiness file, the assigned inspector (or designee) should direct the applicant to create a new application for a replacement airworthiness certificate to correct the error(s). When issuing a replacement special airworthiness certificate, the operating limitations issued with the original airworthiness certificate must be issued with the replacement special airworthiness certificate, or an amended application should be created.
(2) Do not issue a replacement airworthiness certificate for the scenarios provided for under paragraph 2-4.a(1) of this order for amending an airworthiness certificate.
Note: Replacing an airworthiness certificate is an administrative function and does not require a finding of airworthiness.
(3) Procedures for Replacing an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review the Request. FAA Form 8130-6 is not required; a signed statement is acceptable. Inspect the signed statement requesting the replacement certificate to verify that it is from the registered owner, his or her agent, or an operator and includes the aircraft registration number, make, model, and S/N and a valid reason for replacing the certificate.
(b) Review FAA Airworthiness Records on File at the Registry. A replacement airworthiness certificate may be issued if all the information from the lost or mutilated certificate can be positively established from the maintenance records, the certificate's remains, or the Registry. If there is insufficient data on which to base issuance of the replacement certificate, including the original operating limitations, do not issue the replacement certificate; advise the applicant to apply for a new airworthiness certificate.
(c) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.f of this order is not required. Review records as necessary to verify that the applicant’s request is valid, and that the aircraft is eligible for the requested airworthiness certificate. When replacing an airworthiness certificate because the aircraft registration number has changed, review both the registration and, when applicable, Aeronautical Center Form 8050- 64, Assignment of Special Registration Marks, to verify the aircraft is currently registered and to verify the current N-number.
(d) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.e of this order is not required. Inspect the aircraft as necessary to verify that the applicant’s request is valid, and that the aircraft is eligible for the requested certificate.
(e) Issue Airworthiness Certificate. When issuing a replacement for a special airworthiness certificate, the operating limitations must match the operating limitations on the original certificate verbatim. Only modifications to the operating limitations for correcting administrative mistakes are allowed. When issuing a replacement for a standard airworthiness certificate that lists an exemption or exemptions in block 5, follow paragraph A-3.e to complete block 5.
d. Surrender. Verify that the aircraft owner’s written authorization to surrender the airworthiness certificate states why the certificate is being surrendered. Except for an expired experimental airworthiness certificate, email a digital copy of the authorization and certificate to AFB-710 “[email protected],” for retention in the permanent airworthiness files.
e. Transfer. An airworthiness certificate is transferred with the aircraft (§ 21.179), for example, if there is a change of ownership or transfer of registration.
Chapter 2. › Figure 2-1. Common Steps for Issuing an Airworthiness Certificate
Figure 2-1. Common Steps for Issuing an Airworthiness Certificate
Review application (2.3.b)
Review airworthiness records
on file at the Registry (2.3.c)
Identify potential safety
hazards (2.3.d)
Review aircraft records (2.3.e)
Inspect aircraft (2.3.f)
Document reviews &
inspections (2.3.g)
Issue airworthiness certificate (2.3.h) or letter of denial (2.3.i)
arro
Review records & forward to
the Registry (2.3.j)
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) › 3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)).
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183)
3-1. Introduction. This chapter provides policies and procedures for issuing standard airworthiness certificates under § 21.183 for aircraft in the normal, utility, acrobatic, commuter, or transport category; manned free balloons; and special class aircraft designated by the FAA under § 21.17(b).
3-2. Common Requirements for Reviewing Aircraft Records. In addition to the common requirements for reviewing aircraft records in paragraph 2-3.e of this order, the following requirements also apply to certain airplanes per § 21.183:
Note: This list is not exhaustive. Other requirements may apply and require verification during your review of aircraft records, such as § 91.1505, Repair assessment for pressurized fuselages, and § 91.1507, Fuel tank system inspection program.
a. Noise. Per § 21.183(e), for an application to issue an original standard airworthiness certificate, review records to verify compliance with the applicable noise requirements of 14 CFR Part 36 or Part 91, subpart I, as applicable.
b. Emergency Exit. Review records for transport category airplanes manufactured after October 16, 1987, to verify compliance with the passenger emergency exit requirements of § 21.183(f).
c. Fuel Venting and Exhaust Emission. Per § 21.183(g), review records to verify compliance with the fuel venting and exhaust emission requirements of Part 34.
3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)). Aircraft manufactured under a PC are eligible for issuing an airworthiness certificate without further showing in accordance with § 21.183(a). The submission of FAA Form 8130-9 is not required. The FAA may inspect each aircraft to determine conformity with the approved type design. The inspection frequency may be adjusted by the geographic CM section or the CM branch, which has certificate management responsibility over the certificate holder. Consider the following in adjusting inspection frequencies: recent changes in the aircraft design, the quality system, personnel, and the supply base; and recent customer-identified deficiencies, quality escapes, service difficulties, incidents, and accidents. When inspecting an aircraft, follow the applicable procedures in paragraphs 2-3 and 3-2 and the following:
a. Review Aircraft Records.
(1) Review the PC and the production limitation record (PLR) to verify that the holder is authorized to manufacture the applicable aircraft make and model.
(2) Review the manufacturer’s records to verify that quality system procedures have been completed satisfactorily, including production flight testing of the aircraft.
b. Reserved.
3-4. New Aircraft Manufactured Under a TC Only (§ 21.183(b)). Follow the common procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2 of this order and the following:
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) › 3-6. Used Aircraft (§ 21.183(d)).
a. Review Application.
(1) Verify that the manufacturer is still authorized to manufacture under a TC since such authorizations are of limited duration.
(2) Review FAA Form 8130-9, Statement of Conformity, to verify proper completion and to verify the applicant certifies the aircraft is airworthy and was flight tested. Refer to FAA Order 8110.4 for additional FAA Form 8130-9 information.
b. Review Aircraft Records.
(1) Review the FAA’s inspection records for each aircraft to verify that any prior findings have been properly addressed.
(2) Review the manufacturer’s records to verify that any interim quality system procedures have been completed satisfactorily, including production flight testing of the aircraft.
(3) Verify that any nonconformities involving material review actions have been resolved through the responsible certification branch before issuing an airworthiness certificate.
c. Inspect Aircraft. You must inspect each aircraft presented for issuance of a standard airworthiness certificate to find the aircraft airworthy. Adjust inspections as necessary for any significant changes in manufacturing systems, procedures, or personnel or when changes have been introduced into the aircraft. Inspect the aircraft to verify conformity to its TC, including applicable ADs. This does not imply that every article must be subjected to a conformity inspection. Conformity inspections of articles should only be conducted when, in the FAA’s judgment, conformity cannot be substantiated by any other means.
3-5. New Import Aircraft, Foreign SOM (§ 21.183(c)). Follow the procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2 and chapter 20 of this order.
3-6. Used Aircraft (§ 21.183(d)). This paragraph applies to issuing a standard airworthiness certificate for a used aircraft, including a surplus aircraft of the U.S. Armed Forces. Follow the common procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2 of this order and the following:
a. Review Aircraft Records.
(1) Review aircraft maintenance records to verify the aircraft was inspected and found airworthy per § 21.183(d)(2) within 60 days before the date of the application. The rule requires the aircraft to have been inspected per the performance rules for 100-hour inspections in § 43.15, meaning the use of a checklist that includes at least the scope and detail of Appendix D to Part 43. In lieu of a 100-hour type inspection, it is acceptable for the aircraft to have been inspected with an equivalent performance standard acceptable to the FAA, such as any
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) › 3-7. Manned Free Balloons.
inspection program prescribed under § 91.409. If inspected per an approved progressive or continuous airworthiness inspection program, this means all inspections must be current. For aircraft with no manufacturer’s recommended inspection program, the inspection program must be one approved by the FAA. This inspection program must have the equivalent performance standard defined to be eligible for compliance with any aircraft certificate conformity inspection used to issue an airworthiness certificate. Verify that one of the following persons performed this inspection and found the aircraft airworthy:
(a) The manufacturer;
(b) The holder of a repair station certificate issued under 14 CFR Part 145;
(c) The holder of a mechanic certificate as authorized in 14 CFR Part 65; or
(d) The holder of a certificate issued under 14 CFR Part 119 having a maintenance and inspection organization appropriately rated for the type of aircraft involved.
(2) Surplus Aircraft of the U.S. Armed Forces. Review:
(a) FAA Form 8130-31, Statement of Conformity – Military Aircraft, or its predecessor, FAA Form 8130-2, Conformity Certificate – Military Aircraft. This form is issued to a military service at the time of manufacture to identify deviations from the FAA TC for a new military aircraft that was derived from an FAA, type-certificated aircraft. Verify that any deviations have been corrected. Refer to FAA Order 8110.101, Type Certification Procedures For Military Commercial Derivative Aircraft, concerning the use of these forms.
(b) Military maintenance records to determine if operating limitations were exceeded; if so, contact the responsible certification branch for an airworthiness assessment of all exceedances.
(c) Records of engines, gearbox assemblies, landing gear, instruments, or other articles establishing that they originally conformed to the TC and have been maintained per applicable FAA requirements. Military maintenance and/or repair station records may be used for this purpose.
b. Used, Imported Aircraft. For an application for a standard airworthiness certificate for a used, imported aircraft, refer to Chapter 20 of this order for additional related policies and procedures.
3-7. Manned Free Balloons. Follow the applicable procedures for issuing a standard airworthiness certificate in paragraphs 3-3 through 3-6 of this order and the following:
a. Inspect Aircraft. Inspect the aircraft to verify that the applicant is presenting a complete aircraft for issuance of a standard airworthiness certificate. For a manned free balloon, a complete aircraft consists of an envelope with an eligible burner, fuel system, and basket; verify that the combination is allowed per the TCDS. You may not issue a standard airworthiness certificate for an article only.
b. Delivery of New Envelopes. Manufacturers of manned free balloons may deliver a balloon envelope when the envelope is the only article ordered. A manufactured balloon envelope assembled to a burner and basket and flight tested is eligible for a standard airworthiness certificate. The envelope, along with the standard airworthiness certificate and the logbook, may be delivered without the burner and basket. The envelope may then be assembled to a different burner and basket per the TC. A person may interchange the burner and basket as a preventive maintenance task described below.
c. Changing the Burner and Basket. A new airworthiness certificate is not required when the aircraft is disassembled, and a different burner and basket combination is installed, as the TC allows. Reassembly of the envelope and bottom-end articles into a complete aircraft may be performed as preventive maintenance under 14 CFR Part 43, appendix A, paragraph (c)(27). The aircraft records must properly reflect the installation of the bottom-end articles and record the new empty weight. The bottom-end components must be in a current “annual or 100-hour” inspection status. The individual records of the bottom-end articles must be maintained.
d. Replacement Envelopes. If an envelope is provided only as a replacement article without obtaining a new aircraft S/N, registration number, or ID plate, the installation of the replacement envelope is a maintenance item under Part 43. This requires appropriate documentation of the work performed and a return to service entry in the aircraft records by a person authorized to perform the maintenance. The aircraft ID plate, S/N, and registration number are carried over from the previous aircraft envelope.
Section 1. General › 4-1. Introduction.
Chapter 4. Issuing Special Airworthiness Certificates
Section 1. General
4-1. Introduction.
a. This section provides common procedures for issuing a special airworthiness certificate. A special airworthiness certificate may be issued for:
(1) Primary. A primary category aircraft under § 21.184.
(2) Restricted. A restricted category aircraft under § 21.185.
(3) Limited. A limited category aircraft under § 21.189.
(4) Provisional. An aircraft that meets Part 21, subpart C, Provisional Type Certificates, and subpart I, Provisional Airworthiness Certificates.
(5) Light-Sport. A light-sport category aircraft under § 21.190.
(6) Experimental Purposes. An aircraft for an experimental purpose under § 21.191.
(7) Special Flight Permits. An aircraft that does not currently meet applicable airworthiness requirements but is capable of safe flight and meets §§ 21.197 and 21.199.
b. Section 2 of this chapter provides common policies and procedures for issuing a special airworthiness certificate for experimental purposes.
c. Additional policies and procedures specific to certain aircraft categories, experimental purposes, and SFPs are provided in subsequent chapters of this order.
d. The following special airworthiness certificates have similar provisions for crew training and for demonstration flights. Note the differences among the scopes of these provisions to ensure you issue the appropriate certificate.
(1) Experimental airworthiness certificate for crew training under § 21.191(c) is for training the applicant’s flight crews. This normally includes a manufacturer’s employees who need to be trained in experimental aircraft but may also include a company/applicant that operates an experimental aircraft and needs to train its pilots/employees to obtain an appropriate type rating or authorization to serve as a pilot in command (PIC) of the aircraft.
(2) Experimental airworthiness certificate for market survey under § 21.191(f) is for purposes of conducting market surveys, sales demonstrations, and customer crew training only as provided for in § 21.195. Customer crew training is for training the customer’s flight crews.
(3) An SFP under § 21.197(a)(5) is for aircraft manufacturers for conducting customer demonstration flights in new production aircraft that have satisfactorily completed production flight testing.
Section 1. General › 4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores.
(4) An aircraft manufacturer, therefore, could conduct sales/customer demonstration flights as experimental for market survey or with an SFP under § 21.197(a)(5).
4-2. Common Procedures for Issuing a Special Airworthiness Certificate. Except for issuing an SFP, follow the common procedures in paragraph 2-3 of this order for issuing an airworthiness certificate and appendix D to this order for issuing operating limitations. As applicable, include the elements of paragraph 4-4 in the records review and aircraft inspection.
4-3. Flight Operations Outside the United States. A special airworthiness certificate does not authorize flight operations over a foreign country. However, the FAA may issue the certificate when the applicant intends to operate the aircraft over other countries if the applicant meets the requirements for that certificate. A U.S. special airworthiness certificate is often helpful to a civil aviation authority (CAA) when issuing permission to operate the aircraft in or over its country. If the FAA knows the affected CAA will not permit the operation of the aircraft in or over its country, the FAA cannot deny issuance of the certificate if the applicant has met the requirements for that certificate. In any case, an ASI should make the applicable CAA(s) aware of the aircraft, its category or experimental purpose, and the operating limitations for the aircraft.
4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores. These systems are usually associated with former military or certain restricted category aircraft.
a. Maintenance of Jettisonable Stores. Verify that the applicant’s inspection program includes maintenance and inspection of jettisonable stores systems per the manufacturer’s procedures.
b. Ejection Seat Systems. Verify that the ejection seat system has been approved for use in the aircraft model by the aircraft manufacturer or by a military service using that aircraft model.
c. Procedures for Securing Aircraft. Verify that the applicant has provisions and procedures for securing the aircraft whenever it is parked to prevent inadvertent operations of a system that uses an explosive device.
d. Airport Notification. Verify that the applicant has notified the airport manager where the aircraft is based concerning the presence of jettisonable stores, any explosive devices, and planned operations of the aircraft from that airport.
e. Marks for Explosive Devices. Verify that the applicant clearly marked all explosive devices on the exterior of the aircraft. Marks must clearly indicate that the aircraft is equipped with explosive devices.
f. Operations with Jettisonable Stores. Except for certain restricted category aircraft, only aircraft with an experimental airworthiness certificate for R&D may be operated with a jettisonable store and only for a test that requires jettisoning that store.
Section 2. Experimental Airworthiness Certificates
Section 2. Experimental Airworthiness Certificates › 4-6.
4-5. Introduction. This section provides common policies and procedures for issuing special airworthiness certificates for experimental purposes.
4-6. Common Procedures for Issuing an Experimental Airworthiness Certificate (§ 21.191). Follow the procedures for issuing an airworthiness certificate in section 1 of this chapter and the following:
a. Review Application.
(1) Verify the program letter meets § 21.193:
(a) Purpose. Ensure the program letter clearly describes how the aircraft will be used and verify the operation meets a § 21.191 purpose. Guidance is contained in Appendix C. Using the same aircraft for overlapping programs is acceptable, and the program letter can outline one or more programs. After showing compliance with § 91.319(b), the aircraft can be used to support other aircraft in the program or other experimental programs the applicant has underway. If applicable, verify that such support activities are described in the program letter.
(b) Time. Verify that the program letter contains the estimated number of flights or flight hours, and the period of calendar time required for the operation.
(c) Area. Verify that the program letter defines the specific area over which the aircraft will be operated, including routes to and from specified airports. A written or pictorial description or an aeronautical chart is acceptable. You may consult with an operations ASI, per paragraph 1-6, to ensure the suitability of the area.
(d) Drawings or Photographs. Unless converted from a previously type-certificated aircraft without significant change in the external configuration, verify the program letter includes three-view drawings or three-view dimensioned photographs of the aircraft.
Note: If the three-view drawings or photographs are marked as proprietary in the program letter, the ASI will review the drawings and photographs. Do not send any documents to the Aircraft Registration Branch that are labeled as proprietary, confidential, company-sensitive, subject to International Traffic in Arms Regulation (ITAR) or Export Administration Regulations (EAR), or contain any other label indicating the document is restricted from public or foreign disclosure.
(2) Eligibility. Verify that the program letter supports the requested experimental purpose, and that purpose is one listed in § 21.191. For example, except as provided for under §§ 21.191(f) and 21.195, brokering or marketing of experimental aircraft is not a valid experimental purpose; this includes an individual who manufactures, imports, or assembles an aircraft and then applies for an experimental airworthiness certificate to help sell the aircraft.
Section 2. Experimental Airworthiness Certificates › 4-7. Flight Test Areas.
(3) Information for Operating Limitations. Verify that the level of detail in the program letter is sufficient to enable the FAA to prescribe all appropriate operating limitations.
(4) Multiple Purposes. If the applicant is seeking an experimental airworthiness certificate for multiple purposes, verify that the program letter clearly documents all the items listed in paragraph 4-6.a(1) of this order separately for each purpose. In addition, verify that the program letter describes any required configuration changes for changing purposes, including adding or removing equipment and enabling or disabling systems; required configuration changes are typically specified via the modification or addition of operating limitations. Configuration changes may also require adjustments to the aircraft inspection program. Refer to paragraph 4-8 of this order for additional policies and procedures concerning multiple experimental purposes.
b. Inspect Aircraft.
(1) Special Aircraft Marks. Inspect the aircraft to verify that the aircraft is marked “Experimental.”
(2) Information to Safeguard the Public. Per § 21.193(c), upon inspecting the aircraft, obtain any pertinent information from the applicant as necessary to safeguard the general public.
c. Issue Airworthiness Certificate (paragraph 4-2).
(1) Flight Tests. For flight tests, refer to paragraph 4-7 of this order for additional policies and procedures concerning flight test areas.
(2) Reserved.
4-7. Flight Test Areas.
a. Assigned Flight Test Area.
(1) Section 91.319(b) of 14 CFR requires that an unproven experimental aircraft be
assigned to a flight test area until it is shown that the aircraft is controllable throughout its normal range of speeds, is controllable throughout all maneuvers to be executed, and has no hazardous operating characteristics or design features. Per § 91.305, verify the assigned test area includes areas over open water or sparsely populated areas and that it has light air traffic. Evaluate each application to determine that the flight test area and airports are sufficient to accomplish the program. In some cases, assigning multiple flight test areas and airports may be required to accommodate various aircraft configurations, types of operations, airport facilities, or safety hazards.
(2) It is recommended that you coordinate the applicant’s proposed flight test area
with an operations ASI. In addition, consider coordinating with the applicable Air Traffic Control (ATC) facilities. The General Aviation and Commercial Division
Operations Branch (AFS-830) is available to assist in resolving any issues in assigning flight test areas.
b. Airport Adjacent to Densely Populated Area.
(1) Acceptable Approach/Departure Route. In the case of the first flight of an aircraft from an airport adjacent to densely populated areas, but with at least one acceptable approach/departure route that is compliant with § 91.305, ensure a route is selected which subjects the fewest number of persons and the least property to possible hazards. The description of the area selected by the applicant and agreed to by the FAA must be included in the operating limitations.
Note: An acceptable approach/departure route must comply with § 91.305 and provide a reasonable opportunity to execute an off-airport emergency landing that will not jeopardize other persons or property.
(2) No Acceptable Approach/Departure Route. In the case of an aircraft located at an airport with no acceptable approach/departure route, you may issue the airworthiness certificate that includes an operating limitation that prohibits operations at that airport. Advise the applicant to relocate the aircraft to an airport suitable for flight testing.
c. Aerobatics.
(1) Aerobatic maneuvers may be permitted while the aircraft is in the assigned flight test area if the aircraft has the capability of such flight. However, these maneuvers should not be attempted until sufficient flight experience has been gained to establish that the aircraft is controllable.
(2) Aerobatic maneuvers that have been demonstrated in the assigned flight test area should be documented in the aircraft records. Only those aerobatic maneuvers that have been successfully accomplished should be permitted after leaving the assigned flight test area.
d. Duration of Assignment to the Flight Test Area.
(1) Duration. Judge each program duration based on the type, complexity, and condition of the aircraft and the complexity of the test. For example, flight testing in conjunction with a minor STC alteration may require only one hour in an assigned flight test area, while the initial operation of a prototype jet aircraft or a former military aircraft may require much more time. In some cases, it may be appropriate to specify the duration as completion of the flight test program, not a fixed flight time.
(2) Finding Compliance. You may amend the operating limitations to permit flight outside of the assigned flight test area after the applicant shows and you find compliance with § 91.319(b). Your finding may be based on a statement by the pilot in the aircraft maintenance records that the aircraft is controllable throughout its normal range of speeds and throughout all the maneuvers to be executed and has no hazardous operating characteristics or design features. You may also witness flights or inspect the aircraft if deemed necessary. You may also find compliance based on the FAA-approved procedures of a PC holder or modifier, as
Section 2. Experimental Airworthiness Certificates › 4-8. Multipurpose Experimental Airworthiness Certificates.
discussed in paragraph 4-9 of this order. An application is required to amend the airworthiness certificate/operating limitations.
e. Phased Operating Limitations. Phased operating limitations are issued for exhibition, air racing, operating amateur-built aircraft, operating primary kit-built aircraft, operating light-sport category kit-built aircraft, operating former light-sport category aircraft, or operating light-sport aircraft under § 21.191. Phased operating limitations are further discussed in paragraph D-3 of Appendix D.
(1) Phase I typically means the initial period of flight testing for an applicant to demonstrate that the aircraft complies with § 91.319(b). For example, Phase I flight testing is required for a newly assembled amateur-built aircraft, newly assembled kit-built light-sport category aircraft, other experimental aircraft that were disassembled and re-assembled, and expansions of flight limitations beyond what was previously demonstrated under Phase I testing. Phase I may also apply to an aircraft that has been in long term storage or following a major alteration.
(2) Phase II means the period after satisfactory completion of Phase I testing.
f. Operating Outside Flight Test Areas. Except as provided for in paragraphs 4-9 and D-3 of appendix D to this order, operation of the aircraft outside an assigned flight test area will require the issuance of an amended experimental airworthiness certificate with amended operating limitations if Phase II operating limitations were not included with the certificate.
4-8. Multipurpose Experimental Airworthiness Certificates. An experimental airworthiness certificate may be issued for more than one of the purposes under § 21.191. When more than one purpose is requested, verify that the operator has adequate procedures for ensuring the aircraft is in condition for safe operation when changing purposes. The issuance of multiplepurpose certificates for R&D and showing compliance should be limited to PC holders; this may be extended to modifiers (§ 21.195(c)) when justified. PC holders or modifiers may submit a procedure that meets the requirements of paragraph 4-9 of this order to their geographic responsible FAA office for approval.
Note: Issuing multiple certificates for a restricted category aircraft under § 21.187 is different than issuing an experimental airworthiness certificate with multiple purposes or issuing multiple experimental airworthiness certificates for multiple purposes. Issuance of multiple certificates for restricted category aircraft is covered by Chapter 7 of this order.
a. Options. Use your discretion in determining the best option for the desired use. Options include issuing multiple certificates, issuing a multipurpose certificate, or not allowing the aircraft to be used for more than one purpose.
b. Configuration Changes. Consider how the aircraft configuration may change and how the aircraft's operation may change from one purpose to another. This information should be included in the program letter because it may impact the operating limitations issued to the applicant, and/or additional inspections may be required when changing purposes.
Section 2. Experimental Airworthiness Certificates › 4-9.
Example 1: The holder of an experimental exhibition certificate seeks an experimental R&D certificate for flying as a chase aircraft in support of an R&D project. No alterations to the aircraft are necessary. An applicant could be allowed to hold both exhibition and R&D certificates. No further action is required when the R&D project is completed because the applicant still holds the exhibition certificate.
Example 2: The holder of an experimental exhibition certificate seeks an experimental R&D certificate to test new sensor technology. The operator will need to appreciably modify the aircraft. The aircraft should only hold the R&D certificate.
Example 3: An applicant for an experimental airworthiness certificate for operating an amateur-built aircraft mentions they intend to race the aircraft. A single certificate with both purposes listed may be appropriate in this situation.
Note: Configuration changes and operational differences should also be considered if the applicant intends to conduct public or military aircraft operations while holding the experimental airworthiness certificate.
4-9. PC Holder’s or Modifier’s Procedure for Operating Experimental Aircraft. A PC holder or aircraft modifier who applies regularly for special airworthiness certificates to conduct flight tests following the same procedures may submit its procedures to its geographically responsible FAA office for approval. Coordinate the document review with a local operations inspector. Having an approved procedure benefits the applicant and the FAA with increased standardization, simpler program letters, reduced duplication of coordination among FAA offices, and timelier issuance of airworthiness certificates. After approval, the procedure may be listed in the operating limitations as indicated in Appendix D to this order. The FAA may exclude certain aircraft from the privileges of all or part of this procedure, such as the first aircraft of a new model or a non-production R&D aircraft. These procedures must not provide relief from any operation limitation or regulation. The procedure should include the following elements:
a. Flight Test Area. A description of the flight test area that meets paragraph 4-7 of this order.
b. Flight Log. A daily flight log that records the completion of pre-flight inspections and compliance with § 91.319(b) for the duration of the certificate.
c. Flights Outside the Test Area. A description of the method used to conduct and record necessary flights outside the test area, and for maintaining these records. This procedure will remain active for the duration of the certificate and will eliminate the need for the PC holder to obtain approval for each flight.
d. Carriage of Persons. A description of the method used to define the persons who may be carried during these flight operations that includes:
Section 2. Experimental Airworthiness Certificates › 4-10. Former-Military Aircraft Operated for Experimental Purposes.
(1) A requirement that the PIC advise each person of the experimental nature of the aircraft, per § 91.319(d).
(2) A method of recording persons carried on each flight for the duration of the certificate.
(3) A provision that no persons may be carried in the aircraft during flight unless that person is required for the purpose of the flight. Persons other than flight crew members may be carried when the following conditions are met:
(a) The aircraft is of the same basic model that previously has shown compliance with §§ 91.319(b) and 21.195.
(b) Flight tests do not include intentional maneuvers involving abrupt changes in the aircraft’s attitude, abnormal attitudes, or abnormal acceleration/deceleration not necessary for normal flight.
(c) The procedures specifically cover the types of flying permitted while carrying persons other than flight crew members.
e. Multiple Experimental Purposes. A description of the method used to determine whether an aircraft is in a condition appropriate for the purpose intended when changing from one experimental purpose to another, including documenting the results of this determination in a maintenance record or daily flight sheet.
f. Carrying the Approved Procedure. A requirement that a copy of the procedures approved under paragraph 4-9 of this order be carried in the aircraft while operating under the privileges of this procedure. A copy of this procedure may also be included or directly referenced in the PC holder’s quality manual for the convenience of the manufacturer and the FAA.
g. Other. Any other procedures deemed necessary in the interest of safety.
h. Approval of this procedure. Review and approval may require the coordination of different offices within the FAA (such as CM sections, responsible Flight Standards District Office (FSDO), Certificate Management Office (CMO), International Field Office (IFO), the Air Traffic Control (ATC), the Aircraft Evaluation Division (AED), and outside the agency. This could include airport first responders, such as fire departments and security. The FAA office responsible for oversight of the manufacturer is responsible for coordination.
4-10. Former-Military Aircraft Operated for Experimental Purposes.
a. Advising the Applicant. Advise the applicant to review the following FAA ACs.
(1) FAA AC 21-54, Experimental Airworthiness Certification of Certain Former- Military Aircraft.
(2) FAA AC 43-209, Recommended Inspection Procedures for Former Military Aircraft.
b. Eligibility.
(1) If a TC has not been issued for the aircraft, it may be eligible for a special airworthiness certificate for the experimental purpose of R&D, crew training, exhibition, or air racing.
(2) Some aircraft may have high-risk factors that may be impractical to mitigate and, consequently, may not be eligible for an airworthiness certificate.
c. Identify Potential Safety Hazards. Given the variety of aircraft types, models, alterations, operational histories, and airworthiness ramifications of possible long-term storage, becoming familiar with former military aircraft is especially important. Additional considerations for becoming familiar with the aircraft and with potential safety hazards include the following:
(1) Identify the aircraft model and/or series and the type of engine(s), propellers, and other systems installed, as applicable. Obtain as much historical information as possible, including S/Ns, aircraft, and component life limits, overhaul dates, airframe cycles, and engine time and cycles.
(2) Review accident and incident data for the aircraft model. Data can be retrieved from the NTSB database of accidents and incidents, the FAA, and other international and military sources.
(3) Review available aircraft type club information.
(4) Review the ownership history of the aircraft. This may provide information on how the aircraft was previously operated and maintained, which may have implications for the airworthiness inspection.
(5) Become familiar with the scope of any restoration, repairs, and maintenance conducted by or for the applicant. It is also helpful to become familiar with the general condition of working/storage areas, the availability of spare parts, and equipment before conducting the formal records inspection.
(6) Ensure the operator has a complete set of the applicable military flight, inspection, and maintenance manuals for the aircraft and inspection and maintenance manuals for the engine.
(7) Ensure the operator has applicable military technical orders to address known issues related to airworthiness, maintenance, and servicing.
(8) Identify any high-risk factors associated with the aircraft's design, manufacture, maintenance, and operation. Verify that the applicant adequately mitigates any high-risk factors.
d. Import Documentation for Imported, Former-Military Aircraft.
(1) Records for imported former military aircraft that may have weapons installed should include the following documents issued by the Department of Justice, Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF):
(a) ATF Form 6, Application and Permit for Importation of Firearms, Ammunition, and Defense Articles.
(b) ATF Form 6A, Release and Receipt of Imported Firearms, Ammunition, and Defense Articles.
Note: If you have any questions regarding ATF Forms 6 or 6A, contact the ATF Firearms and Explosives Imports Branch.
(2) A product that was declared as parts, scrap, or for museum display on any documentation related to importing that product is not eligible for an airworthiness certificate. This includes documents issued by or for ATF, Customs and Border Protection, or the Department of State.
e. Demilitarization of Former-Military Aircraft.
(1) Removing or Disabling Systems. The FAA may require that some systems be removed or disabled to establish a condition for safe operation for the intended use. For example, safe operation of guns, cannons, targeting radars, electronic jammers, jettisonable stores (including external store pylons and external fuel tanks), or explosive devices may not be feasible under or consistent with the intended experimental purpose. Potential safety hazards related to these systems include accidental firing of guns, accidental release of stores, accidental operation of radars on the ground, compartment fires, and damage to the airframe. These hazards may pose risks to other aircraft and to persons and property on the ground and may not be able to be adequately mitigated via operating limitations. Although some of these systems may be required to support a valid R&D purpose, the applicant and the FAA need to understand the corresponding safety risks and work closely together to determine the feasibility of mitigating these risks via operating limitations.
(2) Additional Information on Weapons. For additional information on aircraft weapons systems, refer to aircraft maintenance manuals and the related weapons delivery manual. Some aircraft manufacturers may offer guidance on aircraft demilitarization. U.S. Air Force Technical Order 00-80G-1, Make Safe Procedures for Public Static Display, can be used as a reference.
f. Ejection Seats.
(1) An inspection program for operable ejection seats will be based on a current manufacturer or military program and will include replacement intervals for life-limited or shelflife-limited components such as pyrotechnic cartridges. These limits cannot be extended without the manufacturer’s approval.
Section 2. Experimental Airworthiness Certificates › 4-12. Pioneer Era Aircraft.
(2) The PIC and flight crew operating aircraft equipped with operational ejection seat(s), whether armed or not armed, must have satisfactorily completed an ejection seat training program per FAA AC 91-87, Ejection Seat Training Programs, within the past 24 calendar months prior to operation for this make and model of aircraft. Passengers of these aircraft must have a safety brief prior to flight per FAA AC 91-87.
(3) The PIC and flight crew operating aircraft that were previously issued an operating limitation that required FAA acceptance or approval of an ejection seat training program, meet that operating limitation if they successfully complete training using an ejection seat training program per the FAA AC 91-87 for the applicable aircraft make/model.
(4) For questions concerning specific aircraft and ejection seat training, contact the responsible FSDO or the Operations section office in the OSS (AFS-830).
g. Drag Chutes. As applicable, verify that the drag chute installation records reflect installation per applicable military installation requirements.
4-11. Flight Operations in Reduced Vertical Separation Minimum (RVSM) Airspace. Experimental aircraft that do not meet the requirements of § 91.180(a) may be allowed to operate in RVSM airspace in certain circumstances as described in § 91.180; Part 91, appendix G; and the Aeronautical Information Manual. In addition, at the time of the flight, ATC must find that the aircraft can be provided with appropriate separation and that the flight will not interfere with or impose a burden on other approved RVSM operations.
a. Flights for aircraft certification and development purposes may be allowed in RVSM airspace. These flights are typically limited to gathering data to show that the aircraft can meet the minimum standards for the operation in RVSM airspace specified in Part 91, appendix G. Further information regarding modifications or alterations that impact RVSM approval can be found in FAA AC 91-85, Authorization of Aircraft and Operators for Flight in Reduced Vertical Separation Minimum (RVSM) Airspace.
b. Aircraft climbing or descending through RVSM flight levels without intermediate level off, to or from flight levels above RVSM airspace, may be accommodated. Obtain data from the operator showing that the aircraft can complete a non-stop climb to flight level 430.
4-12. Pioneer Era Aircraft. Replica, reproduction, restored, and similar aircraft based on aircraft from the pioneer era, before the year 1914 require special consideration. Many of these aircraft have limited maneuverability and are only capable of flying for very short distances. An application for an airworthiness certificate for these aircraft should be coordinated with the Systems Policy Branch (AIR-630) and the General Aviation and Commercial Division (AFS-800) by emailing the coordination mailbox (9-AVS-AIR- [email protected]) to ensure the operating limitations are appropriate for the intended operations.
Chapter 5. Primary Category (§ 21.184) › 5-5.
Chapter 5. Primary Category (§ 21.184)
5-1. Introduction. This chapter provides policies and procedures for issuing a special airworthiness certificate for a primary category aircraft under § 21.184.
5-2. General Requirements. Follow the procedures in Chapter 4, section 1 of this order and the following:
a. Review Aircraft Records. Verify that any special inspection and preventive maintenance program for the applicable aircraft make and model was accepted by the FAA as follows:
(1) For airplanes, acceptance by the AED (MKC-AED) with engineering input by the certification branch where the TC application was made.
(2) For rotorcraft, acceptance by the AED (FTW-AED) with engineering input by the certification branch where the TC application was made.
b. Issue Airworthiness Certificate. Advise the applicant that only a properly qualified pilot/owner may perform preventive maintenance under the special inspection and preventive maintenance program. To be properly qualified, a pilot/owner must successfully complete an FAA-approved course given by an approved aviation maintenance technician school, the PC holder for the pilot/owner’s aircraft or another entity approved by the FAA.
5-3. New Aircraft Manufactured Under a PC (§ 21.184(a)). Follow this order's procedures in paragraphs 3-3 and 5-2.
5-4. New Imported Aircraft (§ 21.184(b)). Follow the procedures in paragraph 5-2 and chapter 20 of this order.
5-5. Aircraft Having a Current Standard Airworthiness Certificate (§ 21.184(c)). As provided for under § 21.184(c), an applicant may exchange a current standard airworthiness certificate for a special airworthiness certificate in the primary category if the aircraft meets § 21.24(a)(1). Note that conversion from standard to primary categories allows an owner/pilot to perform preventive maintenance. The conversion will be made via STC. To issue a special airworthiness certificate under § 21.184(c), follow the procedures in paragraph 5-2 of this order and the following:
a. Issue Airworthiness Certificate.
(1) Obtain the standard airworthiness certificate from the applicant.
(2) Advise the applicant that its aircraft cannot be returned to a standard airworthiness certificate without showing that it meets all the requirements for a standard airworthiness certificate as prescribed by the regulations. Such a showing historically has been difficult when an aircraft has remained in a different classification or category for a lengthy period. To facilitate the return to a standard airworthiness certificate, the aircraft records should
Chapter 5. Primary Category (§ 21.184) › 5-6. Other Aircraft (§ 21.184(d)).
indicate, among other requirements, that the aircraft has been maintained according to the manufacturer’s instructions and that any alterations to the aircraft were either removed or approved by the FAA.
b. Reserved.
5-6. Other Aircraft (§ 21.184(d)). For an application for a special airworthiness certificate in the primary category for an aircraft that meets the criteria of § 21.24(a)(1) and is not covered by paragraphs 5-3, 5-4, or 5-5 of this order, follow the procedures of paragraph 5-2 of this order and the following:
a. Review Aircraft Records. Review applicable records to verify:
(1) The aircraft conforms to an approved primary, normal, utility, or acrobatic type certificate, including compliance with all applicable ADs.
(2) The aircraft has been inspected and found airworthy within the past 12 calendar months per § 91.409(a)(1).
b. Reserved.
Chapter 6. Restricted Category (§ 21.185) › 6-3. New Aircraft Manufactured as Restricted Category (§ 21.185(a)).
Chapter 6. Restricted Category (§ 21.185)
6-1. Introduction. This chapter provides policies and procedures for issuing a special airworthiness certificate for a restricted category aircraft under § 21.185.
6-2. Common Requirements. Follow the procedures in Chapter 4, section 1 of this order and the following:
a. Review Application.
(1) Verify that the restricted category use and special purpose operation is indicated in section II, block B.3 of the application. Refer to FAA Order 8110.56, Restricted Category Type Certification, for the current listing of all special purpose operations approved under § 21.25(b).
(2) If an applicant wishes to obtain approval for a new special purpose operation, refer to FAA Order 8110.56 for guidance in proposing new special purpose operations. Verify the aircraft is type-certificated in the restricted category under § 21.25, CAR 8, or § 21.29 or previously type-certificated in another category and modified for the requested special purpose operation(s).
(3) In the case of an aircraft previously type-certificated in another category and modified for a restricted special purpose operation under § 21.25 or CAR 8, the previously approved TC and the STC or approved data can be considered as the equivalent of a restricted TC. The TC and STC or approved design data should define the design parameters that make up the restricted category TCDS.
(4) Non-U.S.-manufactured aircraft type-certificated in any other category under § 21.29 are not eligible for certification in the restricted category unless the aircraft was issued a new or amended TC under § 21.29 or an STC under § 21.25 and subsequently was modified per the TC or STC. In this instance, § 21.185(b) is the basis for issuing the restricted airworthiness certificate.
(5) Verify that the special purpose operation(s) indicated on the application is listed in the TCDS certification basis or approved by an installed STC.
b. Review Aircraft Records. Per § 21.185(d), review records to verify compliance with the applicable noise requirements of Part 36.
6-3. New Aircraft Manufactured as Restricted Category (§ 21.185(a)).
a. Under a PC. Follow this order's procedures in paragraphs 3-3 and 6-2.
b. Under a TC. Follow this order's procedures in paragraphs 3-4 and 6-2.
Surplus Military Aircraft of a U.S. Armed Force (§ 21.185(b)). Follow the procedures in
paragraph 6-2 of this order.
Chapter 6. Restricted Category (§ 21.185) › 6-6. Import Aircraft (§ 21.185(c)).
6-4. Aircraft Previously TC’d in Another Category (§ 21.185(b)). For modified aircraft that were either surplus military aircraft of a U.S. Armed Force or previously type-certificated in another category and modified for a restricted special purpose operation under § 21.25 or CAR 8, the previously approved TC and the STC or approved data can be considered as the equivalent of a restricted TC. The TC and STC or approved design data should define the design parameters that make up the restricted category TCDS. Follow the procedures in paragraph 6-2 of this order, and verify the following:
a. The alteration conforms to the FAA-approved data, forming the restricted TC's basis.
b. The aircraft is in a good state of preservation and repair and is in a condition for safe operation.
6-5. Recurrent Certificates for Restricted Category Aircraft (§ 21.185(a) or (b)). Follow the procedures in paragraph 6-2 of this order.
6-6. Import Aircraft (§ 21.185(c)). Follow the procedures in paragraph 6-2 and Chapter 20 of this order.
Chapter 7. › 7-2.
Chapter 7. Issue of Multiple Airworthiness Certifications for Restricted Category
Aircraft (§ 21.187)
7-1. Introduction. This chapter provides policies and procedures for issuing multiple airworthiness certificates for a restricted category aircraft under § 21.187.
Note: Issuing multiple certificates for a restricted category aircraft under § 21.187 is different than issuing an experimental airworthiness certificate with multiple purposes or issuing multiple experimental airworthiness certificates for multiple purposes. Issuance of multiple certificates and a multi-purpose certificate for experimental aircraft is covered by paragraph 4-8 of this order.
7-2. Procedures for Issuing Multiple Airworthiness Certificates for an Aircraft. The procedures for issuing multiple airworthiness certificates are a combination of the procedures covering standard (Chapter 3 of this order) and restricted (Chapter 6 of this order) airworthiness certificates, or limited (Chapter 8 of this order) and restricted airworthiness certificates and the following:
a. Review Application.
(1) Determine if the applicant needs one or more certificates. If an aircraft already holds an eligible airworthiness certificate under § 21.187, it is unnecessary to reissue that certificate when exercising the provisions of § 21.187 for issuance of multiple airworthiness certificates for a restricted category aircraft. Issue only the certificate needed. For example, only the restricted category certificate can be issued if the aircraft already holds a standard airworthiness certificate. AWC includes an instructional aid that provides supplemental information on the issuance of a special airworthiness certificate while allowing the applicant to retain a current standard airworthiness certificate when applying for multiple certificates for restricted category aircraft. Ensure section II.D of FAA Form 8130-6 is annotated by the application for the eligible airworthiness certificate the aircraft already holds and to retain.
(2) Verify the aircraft is eligible−
(a) Multiple certificates are required for the requested aircraft categories. An aircraft in the restricted category may be eligible for multiple airworthiness certificates if it can be converted to the normal, utility, acrobatic, commuter, transport, or limited category by removing or adding equipment by simple mechanical means. This provision does not extend to an aircraft in the primary or light sport category, or to an aircraft issued a certificate for an experimental purpose.
(b) By S/N for both categories according to the applicable TCDSs or STC.
b. Review Aircraft Records. Determine if operations in the restricted category would exceed the operating limitations of the other aircraft category. If so, the aircraft may not be eligible for a multiple airworthiness certificate. Any operations outside of the other category operating limitations while operating in the restricted category, unless approved for that aircraft, may make it impossible to return the aircraft to the other category unless a complete engineering
Continue reading ↓ 120 of 555 passages shown