Order 8000.95E Designee Management Policy
This order establishes policy for integrated designee management across the Office of Aerospace Medicine (AAM), Aircraft Certification Service (AIR), Flight Standards Service (FS), and Air Traffic Safety Oversight Service (AOV), as well as the use of the Designee Management System (DMS), which is a web-based tool designed to standardize the management of designees.
Distribution: Electronic Only Initiated By: AVS-60
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
National Policy
ORDER 8000.95E
Effective Date:
SUBJ: Designee Management Policy
This Order is a comprehensive publication establishing policy and procedures for managing all aspects of certain representatives of the Administrator, including selection, appointment, orientation, training, oversight, suspension, and termination.
This Order represents a consolidation of existing policies across the following Aviation Safety services and offices: Aircraft Certification Service, Flight Standards Service, the Office of Aerospace Medicine, and the Air Traffic Safety Oversight Service. This Order also describes updates to the Designee Management System, which is a web-based tool designed to standardize the management of designees.
Kevin Dickert Director Organization Designation Authorization Office, AVS-60
KEVIN A DICKERT
Digitally signed by KEVIN A DICKERT Date: 2026.09.15 12:57:23 -04'00'
09/15/2026
Table of Contents
ii
Table of Contents
Content Page Table of Contents … ii List of Tables … v List of Figures … vi
VOLUME 1. COMMON DESIGNEE POLICY … 1-1
Chapter 1. General Information … 1-1 Chapter 2. Application Process … 1-15 Chapter 3. Selection and Evaluation of a Designee Applicant … 1-18 Chapter 4. Designee Appointment … 1-20 Chapter 5. Responsibilities and Obligations of a Designee … 1-21 Chapter 6. Oversight and Management of a Designee … 1-23 Chapter 7. Training … 1-31 Chapter 8. Annual Request for Extension of a Designee’s Designation … 1-32 Chapter 9. Termination of a Designation … 1-34 Chapter 10. Suspension of a Designation … 1-39 Chapter 11. Other Designee Management Functions … 1-41 Chapter 12. Administrative Information … 1-43
VOLUME 2. AME DESIGNEE POLICY … 2-1
Chapter 1. Introduction … 2-1 Chapter 2. Application Process … 2-2 Chapter 3. Selection and Evaluation of a Designee Applicant … 2-5 Chapter 4. Designee Appointment … 2-7 Chapter 5. Responsibilities and Obligations of a Designee … 2-10 Chapter 6. Oversight and Management of a Designee … 2-13 Chapter 7. Training … 2-19 Chapter 8. Annual Request for Extension of a Designee’s Designation … 2-22 Chapter 9. Termination of a Designation … 2-23 Chapter 10. Suspension of a Designation … 2-27 Chapter 11. Other Designee Management Functions … 2-28
VOLUME 3. DPE, SAE, AND ADMIN PE DESIGNEE POLICY … 3-1
Chapter 1. General Information … 3-1 Chapter 2. Application Process … 3-11 Chapter 3. Selection and Evaluation of a Designee Applicant … 3-23 Chapter 4. Designee Appointment … 3-27 Chapter 5. Responsibilities and Obligations of a Designee … 3-29 Chapter 6. Oversight and Management of a Designee … 3-36 Chapter 7. Training … 3-51 Chapter 8. Annual Request for Extension of a Designee’s Designation … 3-55 Chapter 9. Termination of a Designation … 3-56 Chapter 10. Suspension of a Designation … 3-57 Chapter 11. Other Designee Management Functions … 3-58
iii
VOLUME 4. DADE DESIGNEE POLICY … 4-1
Chapter 1. General Information … 4-1 Chapter 2. Application Process … 4-5 Chapter 3. Selection and Evaluation of a Designee Applicant … 4-8 Chapter 4. Designee Appointment … 4-14 Chapter 5. Responsibilities and Obligations of a Designee … 4-16 Chapter 6. Oversight and Management of a Designee … 4-22 Chapter 7. Training … 4-34 Chapter 8. Annual Request for Extension of a Designee’s Designation … 4-39 Chapter 9. Termination of a Designation … 4-40 Chapter 10. Suspension of a Designation … 4-41 Chapter 11. Other Designee Management Functions … 4-42
VOLUME 5. DME, DPRE, AND DAR-T DESIGNEE POLICY … 5-1
Chapter 1. General Information … 5-1 Chapter 2. Application Process … 5-13 Chapter 3. Selection and Evaluation of a Designee Applicant … 5-23 Chapter 4. Designee Appointment … 5-27 Chapter 5. Responsibilities and Obligations of a Designee … 5-30 Chapter 6. Oversight and Management of a Designee … 5-37 Chapter 7. Training … 5-56 Chapter 8. Annual Request for Extension of a Designee’s Designation … 5-59 Chapter 9. Termination of a Designation … 5-60 Chapter 10. Suspension of a Designation … 5-61 Chapter 11. Other Designee Management Functions … 5-62
VOLUME 6. APD DESIGNEE POLICY … 6-1
Chapter 1. General Information … 6-1 Chapter 2. Application Process … 6-7 Chapter 3. Selection and Evaluation of a Designee Applicant … 6-9 Chapter 4. Designee Appointment … 6-13 Chapter 5. Responsibilities and Obligations of a Designee … 6-15 Chapter 6. Oversight and Management of a Designee … 6-19 Chapter 7. Training … 6-27 Chapter 8. Annual Request for Extension of a Designee’s Designation … 6-30 Chapter 9. Termination of a Designation … 6-31 Chapter 10. Suspension of a Designation … 6-32 Chapter 11. Other Designee Management Functions … 6-33
VOLUME 7. TCE DESIGNEE POLICY … 7-1
Chapter 1. General Information … 7-1 Chapter 2. Application Process … 7-8 Chapter 3. Selection and Evaluation of a Designee Applicant … 7-13 Chapter 4. Designee Appointment … 7-18 Chapter 5. Responsibilities and Obligations of a Designee … 7-20 Chapter 6. Oversight and Management of a Designee … 7-26 Chapter 7. Training … 7-37
iv
Chapter 8. Annual Request for Extension of a Designee’s Designation … 7-42 Chapter 9. Termination of a Designation … 7-43 Chapter 10. Suspension of a Designation … 7-44 Chapter 11. Other Designee Management Functions … 7-45
VOLUME 8. DMIR AND DAR-F DESIGNEE POLICY … 8-1
Chapter 1. General Information … 8-1 Chapter 2. Application Process … 8-2 Chapter 3. Selection and Evaluation of a Designee Applicant … 8-14 Chapter 4. Designee Appointment … 8-17 Chapter 5. Responsibilities and Obligations of a Designee … 8-21 Chapter 6. Oversight and Management of a Designee … 8-23 Chapter 7. Training … 8-33 Chapter 8. Annual Request for Extension of a Designation … 8-35 Chapter 9. Termination of a Designation … 8-36 Chapter 10. Suspension of a Designation … 8-37 Chapter 11. Other Designee Management Functions … 8-39
VOLUME 9. DER DESIGNEE POLICY … 9-1
Chapter 1. General Information … 9-1 Chapter 2. Application Process … 9-7 Chapter 3. Selection and Evaluation of a Designee Applicant … 9-19 Chapter 4. Designee Appointment … 9-22 Chapter 5. Responsibilities and Obligations of a Designee … 9-25 Chapter 6. Oversight and Management of a Designee … 9-26 Chapter 7. Training … 9-33 Chapter 8. Annual Request for Extension of a Designee’s Designation … 9-35 Chapter 9. Termination of a Designation … 9-36 Chapter 10. Suspension of a Designation … 9-37 Chapter 11. Other Designee Management Functions … 9-38
VOLUME 10. DCTO-E DESIGNEE POLICY … 10-1
Chapter 1. General Information … 10-1 Chapter 2. Application Process … 10-2 Chapter 3. Selection and Evaluation of a Designee Applicant … 10-4 Chapter 4. Designee Appointment … 10-6 Chapter 5. Responsibilities and Obligations of a Designee … 10-7 Chapter 6. Oversight and Management of a Designee … 10-9 Chapter 7. Training … 10-15 Chapter 8. Annual Request for Extension of a Designee’s Designation … 10-17 Chapter 9. Termination of a Designation … 10-18 Chapter 10. Suspension of a Designation … 10-19 Chapter 11. Other Designee Management Functions … 10-20
APPENDIX A. DEFINITIONS … A-1 APPENDIX B. ACRONYM LIST … B-1
List of Tables
v
List of Tables
Table Page
Table 1-1. Offices Responsible for Designee Policy … 1-10 Table 1-2. Overall Performance Result … 1-26 Table 3-1. Types of Designees … 3-2 Table 3-2. Certificate Level Testing/Checking Authorizations … 3-3 Table 3-3. Aircraft Category/Class/Privileges Testing/Checking Authorizations … 3-4 Table 3-4. Administrative Authorizations … 3-6 Table 3-5. Specific Eligibility Requirements for Designation as a PE or a CE … 3-15 Table 3-6. Specific Eligibility Requirements for Designation as an LAE, a CIRE, an ATPE, a
PPE, or a Type Rating Examiner … 3-16 Table 3-7. Specific Eligibility Requirements for Designation as an SPE … 3-17 Table 3-8. Specific Eligibility Requirements for Designation as a VAE, VFEE, and EAE ... 3-19 Table 3-9. DPE and SAE PIC Experience Requirements … 3-32 Table 3-10. Initial Training Requirements for Each Designee … 3-51 Table 3-11. Recurrent Training Requirements for Each Designee … 3-52 Table 5-1. Standard Airworthiness Certification Function Codes … 5-2 Table 5-2. Special Airworthiness Certification Function Codes—Primary and Restricted
Categories … 5-3 Table 5-3. Limited Category Function Codes … 5-4 Table 5-4. Experimental Purposes of Market Survey, R&D, or Crew Training Function Codes
… 5-4 Table 5-5. Experimental Purposes of Exhibition or Air Racing Function Codes … 5-5 Table 5-6. Experimental Purposes of Operating Amateur-Built Aircraft Function Codes … 5-6 Table 5-7. Light-Sport Category and Experimental Purposes of Operating Light-Sport
Category Aircraft Function Codes … 5-7 Table 5-8. Export Approvals Function Codes … 5-8 Table 5-9. Domestic Approval of Engines, Propellers, and Articles Function Codes … 5-8 Table 5-10. Other Authorizations Function Codes … 5-9 Table 6-1. Certificate Level Testing Authorizations … 6-2 Table 6-2. Aircraft Category and Class Authorizations … 6-2 Table 6-3. Administrative Authorizations … 6-3 Table 6-4. Special Authorizations … 6-3 Table 6-5. FAA-Conducted Training and Meeting Requirements … 6-28 Table 7-1. Certificate Level Testing and Checking Authorizations … 7-2 Table 7-2. Aircraft Category and Class Authorizations … 7-3 Table 7-3. Administrative Authorizations … 7-4 Table 7-4. Special Authorizations … 7-5 Table 7-5. TCE Training Requirements … 7-38 Table 7-6. FAA-Conducted Training and Meeting Requirements … 7-40 Table 8-1. Minimum Qualification Requirements … 8-6 Table 8-2. Schedule a DO Based on the Highest Risk from this Table … 8-25 Table 10-1. Performance Measures and Oversight Activity Results … 10-13 Table 10-2. FAA-Conducted Training and Meeting Requirements … 10-16 Table A-1. Designee Management Definitions—Common … A-1
List of Figures
vi
Table A-2. Designee Management Definitions—AME … A-2 Table A-3. Designee Management Definitions—DPE, Admin PE, and SAE … A-3 Table A-4. Designee Management Definitions—DADE … A-5 Table A-5. Designee Management Definitions—DME, DPRE, and DAR-T … A-5 Table A-6. Designee Management Definitions—APD … A-7 Table A-7. Designee Management Definitions—TCE … A-7 Table A-8. Designee Management Definitions—DMIR and DAR-F … A-8 Table A-9. Designee Management Definitions—DER … A-9
List of Figures
Figure Page
Figure 3-1. High-Level Selection Process Flow … 3-23 Figure 3-2. High-Level Appointment Process Flow … 3-27 Figure 4-1. High-Level Selection Process Flow … 4-8 Figure 4-2. High-Level Appointment Process Flow … 4-14 Figure 4-3. DADE Checklist … 4-20 Figure 4-4. Sample Designated Aircraft Dispatcher Examiner Surveillance Checklist … 4-33 Figure 4-5. Sample Annual Meeting—Combined Safety Standardization Meeting, FAA
Briefing, and Recurrent Training Agenda … 4-37 Figure 5-1. High-Level Selection Process Flow … 5-23 Figure 5-2. High-Level Appointment Process Flow … 5-27 Figure 5-3. Designee Post-Activity Attachments … 5-54 Figure 6-1. High-Level Selection Process Flow … 6-9 Figure 6-2. High-Level Appointment Process Flow … 6-13 Figure 7-1. High-Level Selection Process Flow … 7-13 Figure 7-2. High-Level Appointment Process Flow … 7-18 Figure 8-1. High-Level Selection Process Flow … 8-14 Figure 8-2. High-Level Appointment Process Flow … 8-17 Figure 8-3. Performance Measures and Oversight Activity Results … 8-26 Figure 10-1. High-Level Selection Process Flow … 10-4 Figure 10-2. High-Level Appointment Process Flow … 10-6
Section 1. Introduction › 6. Implementation.
VOLUME 1. COMMON DESIGNEE POLICY
Chapter 1. General Information
Section 1. Introduction
1. Purpose of This Order. This order establishes policy for integrated designee management across the Office of Aerospace Medicine (AAM), Aircraft Certification Service (AIR), Flight Standards Service (FS), and Air Traffic Safety Oversight Service (AOV), as well as the use of the Designee Management System (DMS), which is a web-based tool designed to standardize the management of designees.
a. This order consolidates orders across Aviation Safety (AVS) services and offices (S/O) and establishes a common policy section for all designees and provides respective volumes for the specific designee types. These policy changes are global in nature and, therefore, are not listed individually.
b. All users of this order must familiarize themselves with its contents and comply with the instructions and guidance contained herein. Many of the procedural functions are not included in the order since they are now incorporated into the functionality of DMS.
2. Audience. The primary audience for this order is AVS designees, Federal Aviation Administration (FAA) managing specialists (MS), and FAA personnel who may interact with designees or designee programs, including FAA management, operational, and administrative employees, as appropriate. The secondary audience is persons seeking to become designees.
3. Where You Can Find This Order. You can find this order on the MyFAA employee website at https://employees.faa.gov/tools_resources/orders_notices and the Dynamic Regulatory System (DRS) at https://drs.faa.gov. Operators and the public can find this order on the FAA’s website at https://www.faa.gov/regulations_policies/orders_notices and DRS.
4. What this Order Cancels. This order cancels FAA Order 8000.95D, Designee Management Policy, dated January 21, 2025.
5. How This Order Is Organized. This order contains ten volumes. Volume 1 contains common policy applicable to all AVS designee types. Volumes 2 through 10 contain policy applicable to specific designee types. Together, these volumes represent the designee management policy for AVS designees, excluding holders of Organization Designation Authorization (ODA).
6. Implementation. Compliance with this order will be phased in by designee type(s) and achieved in accordance with the implementation plans established by each S/O for their respective designee types. Implementation will involve transition from existing management and information systems and designee management policies to the DMS policy and automation. Affected employees and designees will be notified through directive/memo or other means of communication when each implementation will begin and end, as well as when full compliance with this policy is required. FAA employee access and designee login credentials and
c. Volume 3 – Designated Pilot Examiner (DPE), Specialty Aircraft… › (2) Updated definitions for the following:
instructions will be provided at the beginning of each implementation. Timing for release and completion of each implementation plan will depend upon:
a. Availability of the DMS policy and automation for the respective designee type.
b. Completion of transition training in the electronic Learning Management System (eLMS) by the MS and their respective management officials, if required.
7. Explanation of Policy Changes. This revision incorporates the following changes:
a. Volume 1 – Common Designee Policy.
(1) Updates to website links throughout.
(2) Defines order precedence over conflicting AVS directives. See Chapter 1, Section 1, paragraph 8.
(3) Standardizes directive versus guidance terminology. See Chapter 1, Section 1, paragraph 12.
(4) Clarifies legal authority for delegation. See Chapter 1, Section 1, paragraph 13.
(5) Clarifies people not eligible for designee appointment. See Chapter 2, paragraph 2.b.
(6) Clarifies post-application actions to include updating applications and cancellation of applications. See Chapter 2, paragraph 6.
(7) Clarifies requirements of an Overall Performance Evaluation (OPE) if an OPE rating requires a 6-month follow-up. See Chapter 6, paragraph 3.d.(5).
(8) Incorporates FAA Hotline Program requirements. See Chapter 6, paragraph 4.c.(1)
(9) Corrects language to distinguish that Designee Management System (DMS) will notify the Managing Specialist (MS) to remove a suspension or initiate a termination. See Chapter 10, paragraph 2.d.
b. Volume 2 – Aviation Medical Examiner (AME) Designee Policy.
(1) Updates to website links throughout.
(2) Removes yearly requirement for monitoring of license identification number for Quality Management System (QMS) and International Aviation Medical Examiner (AME). See Chapter 6, paragraph 3.b.(2)(c).
c. Volume 3 – Designated Pilot Examiner (DPE), Specialty Aircraft Examiner (SAE), and Administrative Pilot Examiner (Admin PE) Designee Policy.
(1) Updated website links and email addresses throughout.
(2) Updated definitions for the following:
c. Volume 3 – Designated Pilot Examiner (DPE), Specialty Aircraft… › (8) Added requirement BasicMed Comprehensive Medical Examination…
(a) Designated Pilot Examiner (DPE). See Table 3-1.
(b) Sport Pilot Examiner (SPE). See Table 3-2.
(c) Sport Pilot Flight Instructor Examiner (SPFIE). See Table 3-2.
(d) Flight Instructor Examiner (FIE). See Table 3-2.
(e) Flight Instructor Examiner Initial (FIEI). See Table 3-2.
(f) Pilot Proficiency Examiner (PPE). See Table 3-2.
(g) Type Rating Examiner (TYPE). See Table 3-2
(3) Added definition for Rotorcraft Simplified Flight Control (SPE-RSFC). See Table 3-2.
(4) Updated definitions for:
(a) Airplane Single-Engine Land (ASEL). See Table 3-3.
(b) Airplane Multiengine Land (AMEL). See Table 3-3.
(c) Airplane Single-Engine Sea (ASES). See Table 3-3.
(d) Airplane Multiengine Sea (AMES). See Table 3-3.
(5) Added definition for Special Federal Aviation Regulation (SFAR) 73 Qualified. See Table 3-3.
(6) Updated definitions for:
(a) Flight Instructor Recent Experience Examiner (FIRE). See Table 3-4.
(b) Airman Certification Representative for a Part 141 Pilot School With Examining Authority (ACR-141). See Table 3-4.
(c) Airman Certification Representative for a Flight Instructor Refresher Course (ACR-FIRC). See Table 3-4.
(d) Basic Administrative Examiner (BAE). See Table 3-4.
(7) Included Code of Conduct requirement for applications. See Chapter 2, paragraph 2.d.
(8) Added requirement BasicMed Comprehensive Medical Examination Checklist (CMEC) and course completion certificate. See Chapter 2, paragraph 2.g.
c. Volume 3 – Designated Pilot Examiner (DPE), Specialty Aircraft… › (24) Updated limitations to initial Certificated Flight Instructor…
(9) Clarified minimum qualifications for DPE, Specialty Aircraft Examiner (SAE), and Administrative Pilot Examiner (Admin PE) Applicants. See Chapter 2, paragraph 6.a.
(10) Removed paragraph (5) and (6) from specific eligibility requirements for designees with PPE authorizations. See Chapter 2, paragraph 7.b.
(11) Clarified hours as a certified flight instructor for airplane required for specific eligibility requirements for designation as a PE or a CE. See Table 3-5.
(12) Clarified specific eligibility requirements for SPEs. See Chapter 2, paragraph 7.c.(1).
(13) Clarified specific eligibility requirements for SPFIEs. See Chapter 2, paragraph 7.d.(1).
(14) Added rotorcraft helicopter simplified flight controls to specific eligibility requirements for designation as an SPE. See Table 3-7.
(15) Clarified hours as acting pic and hours as a certified flight instructor for airplane. See Table 3-7.
(16) Removed experimental group category from specific eligibility requirements for designation as a Vintage Aircraft Examiner (VAE), Vintage Flight Engineer Examiner (VFEE), and Experimental Aircraft Examiner (EAE). See Table 3-8.
(17) Clarified hours as a pic for specific eligibility requirements for designation as a VAE, VFEE, and EAE. See Table 3-8.
(18) Added SFAR 73 qualified procedures and requirements. See Chapter 2, paragraph 7.h.
(19) Clarified specific eligibility requirements for Admin PEs, as an ACR-FIRC. See Chapter 2, paragraph 7.i.(2)(a).
(20) Clarified National Program Tracking and Reporting Subsystem (NPTRS) entries that would disqualify an applicant. See Chapter 3, paragraph 5.c.(7)(c).
(21) Clarified requirements for a preappointment proficiency check DPE applicants. See Chapter 3, Note to paragraph 5.d.(2).
(22) Added expectation to responsibilities and obligations of a designee. See Chapter 5, paragraph 2.f.
(23) Updated expectations and limitations to specify designees instead of DPEs, SAEs, and Admin PEs. See Chapter 5 paragraph 2.f and 2.h.
(24) Updated limitations to initial Certificated Flight Instructor (CFI) applications. See Chapter 5, paragraph 2.h.(15).
(25) Updated limitations to conditions for test applicants trained by the examiner. See Chapter 5, paragraph 2.h.(18)(a).
(26) Updated DPE and SAE Pilot-In-Command (PIC) experience requirements for rotorcraft. See Table 3-9.
c. Volume 3 – Designated Pilot Examiner (DPE), Specialty Aircraft… › (42) Updated annual request for extension of a designee’s designation.
(27) Clarified definition of “type” for the purposes of Volume 3. See Note to Table 3-9.
(28) Clarified accumulated time that can be counted toward experience. See Note to Table 3-9.
(29) Added Code of Conduct requirements to annual meeting as part of ongoing requirements of a designee. See Chapter 5, paragraph 3.c.(1)(g).
(30) Removed duplicate requirement addressing applicants with only a foreign address. See Chapter 5, paragraph 3.d.
(31) Clarified that DMS establishes direct oversight activities for designees based on their authorized activities. See Chapter 6, paragraph 2.c.(1).
(32) Updated extension limits for direct observations. See Chapter 6, paragraph 2.c.(3).
(33) Updated terminology to reflect National Program Tracking and Reporting Subsystem (NPTRS). See Chapter 6, paragraph 3.a.(2)(a)2.
(34) Clarified timing of minimum direct observations. See Chapter 6, paragraph 3.b.(1)(b).
(35) Clarified FAA reference for FAA Actions to Address Regulatory or Statutory Noncompliance. See Chapter 6, paragraph 3.d.(2).
(36) Updated DMS role in overview. See Chapter 7, paragraph 2.a.
(37) Updated DMS role in documentation. See Chapter 7, paragraph 2.b.
(38) Removed requirement for designee to forward a copy of the certificate of Completion. See Chapter 7, paragraph 3.b.(3).
(39) Clarified DPE recurrent training course information. See Chapter 7, Note to paragraph 3.b.(4).
(40) Updated the procedures Managing FAA offices may take if an applicant/designee fails to satisfactorily complete all required course assignments or pass the post-course test after completing the training curriculum. See Chapter 7, paragraph 3.c.(2).
(41) Updated training limitations. See Chapter 7, paragraph 3.e.
(42) Updated annual request for extension of a designee’s designation. See Chapter 8, paragraph 1 and 2.
e. Volume 5 – Designated Mechanic Examiner (DME), Designated Parachute… › (11) Added “Evaluation Process” to align language with Volume 3.
(43) Updated items that require an MS to initiate an investigation. See Chapter 9, paragraph 2, 2.b, and 2.c.
(44) Revised “pilot certificate or authorization” to “pilot certificate or rating”. See Chapter 9, paragraph 2.c.
(45) Added requirement for Appointing Official (AO) to contact AFS-850 via email for Termination for Cause Review Panel Members. See Chapter 9, paragraph 5.d.
d. Volume 4 – Designated Aircraft Dispatcher Examiner (DADE) Designee Policy.
(1) Updated website links and email addresses throughout.
(2) Removed requirement for Managing Specialist (MS) to review feedback in Oversight Activities. See Chapter 6, paragraph 6.h.
e. Volume 5 – Designated Mechanic Examiner (DME), Designated Parachute Rigger Examiner (DPRE), and Designated Airworthiness Representative—Maintenance (DAR-T) Designee Policy.
(1) Updated website links and email addresses throughout.
(2) Updated the description of Function Code 128. See Table 5-4.
(3) Updated the descriptions for Function Codes 137, 138, 139, and 140. See Table 5-5.
(4) Updated the descriptions for Function Codes 147, 148, 149, and 150. See Table 5-6.
(5) Updated the descriptions for Function Codes 157, 158, and 159. See Table 5-7.
(6) Clarified requirements for DME/DPRE Additional Testing Facilities. See Chapter 2, paragraph 3.e.
(7) Updated additional requirements for DMEs. See Chapter 2, paragraph 4.a.(2)(b) and (c), and paragraph 4.a.(4).
(8) Updated what qualifies as a position of responsibility. See Chapter 2, paragraph 4.c.(1)(c)4.
(9) Removed requirements for minimum qualification requirements for the experimental category operating amateur-built aircraft. See Chapter 2, paragraph 4.c.(2)(a)2, and 3.
(10) Updated minimum qualification requirements for other specific authorizations to issue data approvals in support of major repairs or alterations. See Chapter 2, paragraph 4.c.(4)(b)1 and 3.
(11) Added “Evaluation Process” to align language with Volume 3. See Chapter 3, paragraph 5.a.
f. Volume 6 – AIRCREW PROGRAM DESIGNEE (APD) DESIGNEE POLICY. › (2) Updated direct observation requirements.
(12) Clarified when the lead role should make contact with other evaluation panel members. See Chapter 3, paragraph 5.b.(1).
(13) Clarified evaluation panel tasks. See Chapter 5, paragraph 5.c.(1) and (8).
(14) Clarified DMS actions in appointment considerations. See Chapter 4, paragraph 2.b.(2).
(15) Removed requirement for DAR-T to obtain FAA Form 8130-9. See Chapter 4, paragraph 2.b.(2)(b)1.ix.
(16) Updated testing location information for DME and DPRE Responsibilities. See Chapter 5, paragraph 2.b.(7).
(17) Updated DME and DPRE privileges. See Chapter 5, paragraph 2.c.(4).
(18) Updated DME and DPRE limitations. See Chapter 5, paragraph 2.d.(16).
(19) Clarified approval is required from the geographic expansion coordinator at the office responsible for the geographic area, rather than district, at the area where the activity is requested to be performed. See Chapter 5, Note to paragraph 2.f.(7).
(20) Updated oversight activities. See Chapter 6, paragraph 3.b and 3.b.(1).
(21) Updated records research to Civil Aviation Registry Electronic Services (CARES). See Chapter 6, paragraph 3.b.(3)(d)1.
(22) Removed requirement for MS to report feedback in DMS. See Chapter 6, paragraph 3.b.(7).
(23) Updated preapproval requirements in designee management functions. See Chapter 6, paragraph 5.f.(1).
(24) Added DME testing at multiple domestic Part 147 Aviation Maintenance Technical Schools (AMTS). See Chapter 6, paragraph 5.i.
(25) Clarified DMS actions in training. See Chapter 7, paragraph 2 and 3.a.(1)(a).
(26) Updated recurrent training for DME/DPRE/DAR-T Training. See Chapter 7, paragraph 3.a.(2)(b), 3.a.(4)(a), 3.a.(4)(b), and 3.a.(4)(b)1, 2, 4, and 5.
(27) Updated training limitations. See Chapter 7, paragraph 3.b.(1).
f. Volume 6 – AIRCREW PROGRAM DESIGNEE (APD) DESIGNEE POLICY.
(1) Updated website links and email addresses throughout.
(2) Updated direct observation requirements. See Chapter 6, paragraphs 6.a and 6.b.
i. Volume 9 – Designated Engineering Representative (DER) Designee… › (3) Clarified evidence of knowledge. See Chapter 2, paragraph 4.a.(8).
(3) Removed requirement for MS to review feedback in oversight activities. See Chapter 6, paragraph 6.d.
g. Volume 7 – Training Center Evaluator (TCE) Designee Policy.
(1) Updated website links and email addresses throughout.
(2) Clarified TCE experience requirements. See Chapter 2, paragraphs 3.g. and 3.g.(1).
(3) Clarified surveillance of initial cadre TCEs required minimum experience requirements. See Chapter 2, paragraph 5.h.
(4) Updated direct observation requirements. See Chapter 6, paragraphs 6.a. through 6.a.(5).
(5) Removed requirement for MS to review feedback in oversight activities. See Chapter 6, paragraph 6.e.
h. Volume 8 – Designated Manufacturing Inspection Representative (DMIR) and Designated Airworthiness Representative—Manufacturing (DAR-F) Designee Policy.
(1) Updated website links and email addresses throughout.
(2) Updated minimum qualification requirements for amateur-built and light sport (LS) category aircraft certification function codes. See Table 8-1.
(3) Defined scope of functions not authorized. See Chapter 5, paragraph 2.c.(2).
(4) Clarifies timeframe of direct observation (DO) to align with facility audit and ability to adjust DO cycle in accordance with the parameters of the DMS tool. See Chapter 6, paragraphs 5.a.(2) and (3).
(5) Clarified other oversight activities and considerations. See Chapter 6, paragraph 7.a and 7.b.
(6) Removed requirement to submit a suspension release request in DMS. See Chapter 7, paragraph 3.c.(2).
(7) Updated Automatic suspension requirements. See Chapter 10, paragraph 3.b.
(8) Clarified reinstatement from suspension. See Chapter 10, Note to paragraph 3.c.
i. Volume 9 – Designated Engineering Representative (DER) Designee Policy.
(1) Updated website links and email addresses throughout.
(2) Updated language from “delegation” to “authority.” See Chapter 2, paragraph 4.
(3) Clarified evidence of knowledge. See Chapter 2, paragraph 4.a.(8).
k. Appendices. › (5) Added Flight Instructor Recent Experience Examiner. See Appendix B.
(4) Clarified that an applicant’s training record can be verified in DMS. See Chapter 3, paragraph 5.a.(1)(c).
(5) Clarified request additional authorizations process. See Chapter 6, paragraph 6.a.
(6) Clarified expectations for creating FAA Form 8110-3 outside of DMS. See Chapter 6, paragraph 6.h.(1).
(7) Clarified that all training information is documented and held in DMS. See Chapter 7, paragraph 3.d.
(8) Clarified guidance regarding failure to complete training. See Chapter 7, paragraph 3.e.(1) and (2).
(9) Specified MS training requirements. See Chapter 7, paragraph 4.
j. Volume 10 – Designated Control Tower Operator Examiner (DCTO-E) Designee Policy.
(1) Added Corporate-Level Manager to Designee Program Roles. See Chapter 1, Section 2, paragraph 5.
(2) Updated minimum qualifications for Single-Facility Examiner and Multi-Facility Examiner. See Chapter 2, paragraph 6.a. and 6.b.
(3) Clarified DMS role in certification packages. See Chapter 5, paragraph 2.c.
(4) Removed requirement for FAA DCTO-E Training related to Special Emphasis Oversight. See Chapter 6, paragraph 6.b.
(5) Clarified selections available to MS for Performance Measures and Oversight Activity Results. See Chapter 6, paragraph 8.
(6) Updated performance measures and oversight activity results. See Figure 10-3.
(7) Clarified follow-up actions related to oversight and management of DCTO-Es. See Chapter 6, paragraph 10.
k. Appendices.
(1) Added Simplified Flight Control and definition. See Table A-3.
(2) Added CFR reference for Product definition. See Table A-9.
(3) Added CARES acronym. See Appendix B.
(4) Removed Designee Registration System acronym. See Appendix B.
(5) Added Flight Instructor Recent Experience Examiner. See Appendix B.
Section 1. Introduction › 11. Responsible Offices/Divisions for Designee Policy.
(6) Removed Light Sport Aircraft acronym. See Appendix B.
8. Conflicts With Other FAA Orders. The guidance in this order may conflict with that in other FAA orders and directives. This situation may arise inadvertently or because it is impractical to revise all orders simultaneously. Because FAA Order 8000.95, Designee Management Policy, encompasses all aspects of individual designee management, this order takes precedence over other AVS orders containing conflicting information. If the guidance in this order conflicts with a statute or regulation, the statute or regulation controls.
9. Authority to Change This Order. The AVS Organization Designation Authorization (ODA) Office (AVS-60) has the authority to revise or cancel material in this order. AVS-60 is responsible for coordinating and managing order revisions. AVS-60 is responsible for the content of Volume 1, and the service offices identified in Table 1-1 below are responsible for the content of Volumes 2 through 10. Specific changes requested by service offices must be provided to AVS-60, which will then coordinate with the other organizations to ensure consistency and alignment with DMS policy.
10. Deviations to This Order. Requests to deviate from Volume 1 of this order must be sent to AVS-60 for review and approval/disapproval. Requests to deviate from Volumes 2 through 10 of this order will be sent to the responsible service office identified in Table 1-1 below for review and approval/disapproval. Deviation requests affecting more than one organization or that may require changes to DMS automation must be coordinated across the affected organizations and with AVS-60. When a deviation is requested to Volume 1 of this order, AVS-60 will coordinate with all responsible policy offices before issuance. Service offices may grant deviations to Volumes 2 through 10 of this order, as appropriate. Such deviations do not require precoordination with AVS-60. Once a deviation is granted, the issuing office must provide an electronic copy of the deviation memorandum and a copy of the initiating request to AVS-60.
11. Responsible Offices/Divisions for Designee Policy.
Table 1-1. Offices Responsible for Designee Policy
Designee Type Volume Office/Division Aviation Medical Examiner (AME) Volume 2 AAM-400 Administrative Pilot Examiner (Admin PE)
Designated Pilot Examiner (DPE) Specialty Aircraft Examiner (SAE)
Volume 3 AFS-800
Designated Aircraft Dispatcher Examiner (DADE) Volume 4 AFS-800
Designated Airworthiness Representative – Maintenance (DAR-T) Designated Mechanic Examiner (DME) Designated Parachute Rigger Examiner (DPRE)
Volume 5 AFS-800
Aircrew Program Designee (APD) Volume 6 AFS-800
Training Center Evaluator (TCE) Volume 7 AFS-800 Designated Airworthiness Representative—Manufacturing (DAR-F) Designated Manufacturing Inspection Representative (DMIR)
Volume 8 AIR-600
Designated Engineering Representative (DER) Volume 9 AIR-600 Designated Control Tower Operator Examiner (DCTO-E) Volume 10 AOV-200
Section 2. Designee Overview › 2. Vision of Delegation Management Programs.
12. Directive and Guidance Information.
a. Directive Information.
(1) This type of information is directive in nature and contains terms such as “will” or “must.” These words indicate that the actions are mandatory. “Will not” or “must not” prohibits the action.
(2) The use of these terms does not allow for flexibility.
b. Guidance Information.
(1) This type of information is considered guidance and contains terms such as “should,” “can,” or “may.”
(2) These terms indicate actions that may not be mandatory; however, they are strongly encouraged, permissive, and allow flexibility.
13. Designation of a Designee Authorization.
a. Authority to Delegate. Title 49 of the United States Code (49 U.S.C.) § 44702 empowers the Administrator to “...delegate to a qualified private person, or to an employee under the supervision of that person, a matter related to the examination, testing, and inspection necessary to issue a certificate under this chapter; and issuing the certificate.”
b. Designation Authority. Title 14 of the Code of Federal Regulations (14 CFR) Part 183, Representatives of the Administrator, prescribes the requirements for designating a private person or an organization to act as a representative of the Administrator.
14. Employee Status. A designee is not considered an employee of the U.S. Government and is not federally protected for the work performed or the decisions made as a designee.
15. Role of DMS. DMS will collect, store and process data and information associated with designees and the designee management processes in accordance with FAA recordkeeping requirements. DMS may utilize information from other FAA systems where appropriate and other FAA systems may utilize information from DMS where appropriate.
16. Technical Support. For questions regarding the operation of DMS, contact the AVS National IT Service Desk at 844-322-6948 or via email at [email protected]. For non-system-related questions, please visit the DMS web page to find the email addresses for various designee types.
Section 2. Designee Overview
1. Legal Authority. Title 49 U.S.C. § 44702(d) is the statutory authority to delegate private persons to perform certain authorized functions on behalf of the FAA. These persons are called designees. The designee’s function is vital to enhancing the FAA’s public service role and improving overall safety in the National Airspace System (NAS). The FAA appoints designees to provide airman and aircraft certifications and other services to the public in accordance with FAA policy, guidance, and regulations.
2. Vision of Delegation Management Programs. The FAA delegation programs leverage agency resources; respond to changes in workloads and aviation industry needs in a dynamic environment; demand the highest technical and ethical standards from designees; and ensure
(2) Airworthiness Certification and Airman Examiner. › (c) DPRE.
public, governmental, and industry confidence in aviation safety through strict compliance with certification policies and regulations.
3. Designation Principles. The FAA bases the designation programs on the following principles, which are implicit in the day-to-day management of these programs:
a. Privilege. Designation is a privilege, not a right. The FAA may rescind a designation at any time for any reason the Administrator considers appropriate.
b. Conduct. Designees must not conduct themselves in a manner that casts doubt on their integrity, honesty, moral judgment or character at any time, or conduct any actions that bring discredit to the FAA.
c. Knowledgeable. Designees must be knowledgeable, qualified, and competent.
d. Risk-Based Approach. Management of designation programs must employ a risk-based approach.
e. Essential. Designation programs are essential.
f. Need and Ability. A need for and ability to manage a designee must exist for all designees.
4. Designee Types Covered by This Order. Specific designee types covered by this order include:
a. AAM. AME.
b. FS.
(1) Air Transportation Designated Examiner (ATDE).
(a) APD. 1
(b) DADE.
(c) TCE.
(2) Airworthiness Certification and Airman Examiner.
(a) DAR-T.
(b) DME.
(c) DPRE.
1 For purposes of this order, the term “Aircrew Program Designee” encompasses “aircrew designated examiners” in 14 CFR part 121.
b. Risk Management Strategy (RMS). RMS provides the MS with a… › (5) Monitoring the effectiveness of the decision.
(3) General Aviation Pilot Examiner.
(a) Admin PE.
(b) DPE.
(c) SAE.
c. AIR.
(1) Airworthiness Designee.
(a) DAR-F.
(b) DMIR.
(2) DER.
(a) Company (DER-Y).
(b) Consultant (DER-T).
d. AOV. DCTO-E.
5. Risk-Based Principles.
a. Risk-Based Management. Risk-based management is a continuous process of identifying, analyzing, evaluating, controlling, and monitoring risks that exist with the designee program. DMS captures and manages the data, including the substantiation and documentation of the decisions.
b. Risk Management Strategy (RMS). RMS provides the MS with a methodology for managing hazards and the associated risks related to designee performance. DMS provides the MS with a means to document and track the performance of a designee utilizing the oversight module. The oversight module allows the MS to review and evaluate the disposition of any risks associated with discrepancy findings. This methodology may include the following:
(1) Identifying the discrepancy and determining the hazard;
(2) Analyzing and assessing the risk;
(3) Making a decision;
(4) Implementing the decision; and
(5) Monitoring the effectiveness of the decision.
c. Oversight. Throughout the oversight process for each designee, there are both automated and manual entries within DMS that may trigger specific actions by the MS. Using risk-based principles provides a comprehensive method of managing designees.
Section 3. Minimum Qualifications Overview › 1. Minimum Qualifications of MSs.
Section 3. Minimum Qualifications Overview
1. Minimum Qualifications of MSs. The minimum qualifications for MSs are established by the responsible offices for designee policy. See Chapter 1, General Information, of each volume of the designee type-specific volumes for details.
Chapter 2. Application Process
a. Minimum Qualifications. The designee applicant must: › (2) Be at least 23 years of age.
1. Purpose. This chapter describes the designee application process. This chapter and the corresponding designation type-specific volumes constitute the application process policy.
2. General.
a. Application Information. To learn about the designee program or initiate the designee application process, qualified individuals should access the FAA Designee & Delegations website at https://www.faa.gov/other_visit/aviation_industry/designees_delegations.
b. Eligibility. Anyone may apply to be a designee; however, the following persons are not eligible for appointment:
(1) Current FAA employees.
(2) Designees who have been terminated for cause.
c. Multiple Designee Types.
(1) The FAA may appoint an individual to more than one type of designation. Once appointed, any designee holding multiple designations will have only one designee number.
(2) Designee applicants must complete a separate application for each designation type sought. Each designation is a separate appointment.
d. References. The applicant may provide the following:
(1) Three verifiable character references to substantiate that the applicant possesses integrity and sound judgment.
(2) Three verifiable technical references to substantiate that the applicant possesses the required technical expertise for the designation sought. These references may be the same individuals used as character references.
3. Qualifications. In addition to the requirements in subparagraph 2b above, applicants may also have additional eligibility and qualification requirements which can be found in the appropriate designation type-specific volumes of this order.
a. Minimum Qualifications. The designee applicant must:
(1) Meet FAA English language standards as described in Advisory Circular (AC) 60-28 (as revised), FAA English Language Standard for an FAA Certificate Issued Under Parts 61, 63, 65, and 107; and
(2) Be at least 23 years of age.
Chapter 2. Application Process › 5. Privilege, Not a Right.
b. Character. At all times, the designee applicant must:
(1) Have a high degree of integrity, even when not exercising their delegated authority;
(2) Have a cooperative attitude;
(3) Be able to exercise sound judgment;
(4) Be engaged in the aviation industry;
(5) Have a reputation for dependability and professionalism; and
(6) Be able to maintain the highest degree of objectivity while performing authorized functions.
c. Technical Experience. The applicant must have up-to-date extensive knowledge and experience that is pertinent to the designation being sought.
d. FAA Interaction. Any previous working relationship the applicant had with the FAA must have been positive.
4. Disqualifiers. Applicants will be disqualified for any of the following reasons:
a. Terminated for Cause. See Chapter 9, Termination of a Designation, for details.
b. Convictions and Felonies. Having, within the past 7 years:
(1) Been convicted of any violation of any local, state, or Federal law pertaining to drugs or alcohol.
(2) Been convicted of any felony offenses. A felony offense is considered a conviction where the punishment could have been greater than 1 year regardless of the sentence.
(3) Been imprisoned, been on probation, or is on parole because of a felony conviction (including civilian or military felonies, firearms, or explosive violations).
(4) Been other than “honorably” discharged from the military.
(5) Had an airman certificate (other than medical), rating, or authorization (or foreign equivalent) suspended, revoked, or paid a civil penalty as a result of a violation of any FAA or other Civil Aviation Authority (CAA) regulations (foreign or domestic).
c. Current Disqualifiers. Is currently under investigation, charged indictments, or has a pending action for the items described in subparagraph 4b of this chapter.
5. Privilege, Not a Right. Successfully meeting the minimum qualifications does not guarantee appointment as a designee. During the application process in DMS, the designee applicant will be required to acknowledge the following in DMS:
6. Post-Application. › c. Updating Applications. Applicants must update their applications…
a. Designation is a privilege, not a right.
b. The FAA can terminate any designation at any time, for any reason the Administrator considers appropriate.
6. Post-Application.
a. Retention of Application Data. DMS saves all application data in accordance with FAA Order 1350.14, Records Management.
b. Notification. DMS will automatically notify designee applicants regarding the status of their application by sending a generic email to check the DMS message center. This email is sent to the email address provided during the registration/application process.
c. Updating Applications. Applicants must update their applications whenever information changes and they must validate and verify the application data at least every 12 calendar months. Failure to maintain up-to-date information may affect selection eligibility and appointment as a designee. An application that is updated will remain active in DMS until the applicant is selected, fails to renew the application at the end of the 12-calendar month period, or cancels the application.
d. Cancellation. A designee applicant may cancel an application at any time in DMS.
Chapter 3. Selection and Evaluation of a Designee Applicant
1. Purpose. This chapter describes the common policy related to the selection and evaluation of a designee applicant. This chapter and the corresponding designation type-specific volumes constitute the policy for the selection and evaluation of a designee applicant.
b. Considerations for Determining Ability to Manage. › (3) Adequate funds (e.g., travel allocation) exist to oversee the…
2. General. Selection refers to the identification of qualified designee applicants that best meet the FAA’s needs. Evaluation refers to the FAA’s responsibility to determine if an applicant is the best qualified for appointment.
a. Qualified Applicants. DMS will provide a list of qualified applicants that meet the needs identified by the requesting FAA office.
b. Selection Timeframe. Once DMS presents a list of qualified applicants, the selecting official (SO) should complete the selection action within 30 calendar days.
3. Need and Ability to Manage. The FAA must show the need for specific functions to be delegated and, subsequently, the ability to manage a designee performing those functions before an applicant can be appointed. The managing FAA office, within its sole discretion, determines the need for and ability to manage a designee. The SO at the managing FAA office must validate the need and ability to manage an additional designee by answering a series of questions during the selection process in DMS.
a. Considerations for Determining Specific Need.
(1) The FAA cannot support the certification work and need with existing designees.
(2) The activity in the office has increased or is forecasted to increase and cannot be supported with existing designees.
(3) The FAA has lost an employee or designee resource.
(4) The need for a new designee is driven by the needs of the public and not by the impact on other existing designees or entities.
b. Considerations for Determining Ability to Manage.
(1) The managing office staff has the technical skills and knowledge to manage the designee.
(2) The existing or projected office workload allows the office to effectively manage the designee.
(3) Adequate funds (e.g., travel allocation) exist to oversee the additional or existing designee.
5. Evaluation. The following tasks are part of the evaluation process: › d. Completing Evaluation Checklist. The evaluation panel lead,…
4. Requesting Qualified Applicants.
a. List of Qualified Applicants. Once the FAA establishes the need and ability to manage a designee, the SO can request a list of qualified applicants from DMS. DMS will search active applicants to identify applicants that most closely match the specified criteria.
b. Deviation from Minimum Qualifications. For most designee types, if no qualified applicants are available within DMS, a managing office may request a deviation from the minimum qualification requirements if:
(1) The FAA demonstrates a significant need for the appointment, and
(2) The applicant meets an equivalent qualification or possesses equivalent experience. (See the appropriate designee type-specific volume for more information.)
5. Evaluation. The following tasks are part of the evaluation process:
a. Evaluating Applications. Once DMS has generated a list of applicant(s) based on the search criteria, the SO may choose to review the applications prior to assigning personnel to evaluate the applicant’s qualifications. Determining which applicants will be evaluated for appointment is at the sole discretion of the SO.
b. Assigning Evaluation Panel. Once the SO determines which applicant(s) will be evaluated for appointment, DMS will prompt the SO to assign a panel of individuals to conduct an evaluation of the applicant based on designee type-specific policies.
c. Reviewing Application for Minimum Qualifications. For each applicant, the personnel assigned to evaluate the application will review the application for completeness to ensure that all minimum qualifications have been met.
d. Completing Evaluation Checklist. The evaluation panel lead, depending on the designee type-specific policies, completes an evaluation checklist in DMS for each applicant being evaluated. See Chapter 3 in each designee type-specific volume for more information.
Chapter 4. Designee Appointment › 3. Appointment Duration.
Chapter 4. Designee Appointment
1. Purpose. This chapter describes the common policy associated with the appointment of a selected qualified applicant. This chapter and the corresponding designation type-specific volumes constitute the policy for designee appointment.
2. General.
a. Identity Verification. Prior to appointment, the managing office must verify the identity of the designee applicant. Such identification must include an official government-issued identification with a photograph of the applicant, the applicant’s signature, and the applicant’s residential address, if different from the mailing address. This information may be presented in more than one form of identification.
b. Designee Number. During the application process, DMS assigns a unique nine-digit identification number known as the designee number. However, this number is not known to applicants and only visible to the designee once appointed. This designee number is used in documentation to identify the activities completed by the designee when authorized by the Administrator.
c. Certificate Letter of Authority (CLOA). For each appointment, DMS generates and stores a CLOA that serves as the letter of authority, certificate of authority, and certificate of designation. The CLOA provides a detailed description of the designee’s authorities, limitations, and associated expiration as contained within DMS. A CLOA is available to the designee for each type of designation held and serves as the record of the designee’s authority. Authorized users can view a designee’s authority in DMS. A designee may print a copy of the CLOA but is not required to do so.
3. Appointment Duration. Appointment duration is 1 year from the appointment date. See Volume 1, Chapter 8, Annual Request for Extension of a Designee’s Designation, and the designee type-specific policy for considerations to extend the designation beyond the expiration date.
Chapter 5. Responsibilities and Obligations of a Designee › 3. Ongoing Requirements.
Chapter 5. Responsibilities and Obligations of a Designee
1. Purpose. This chapter describes the common policy associated with the responsibilities and obligations of a designee. This chapter and the corresponding designation type-specific volumes constitute responsibilities and obligations of a designee.
2. Responsibilities. A designee must:
a. Represent the Administrator in a Positive Manner. Each designee must represent the Administrator in a manner that reflects positively on the FAA at all times.
b. Conduct Approved Activities. Each designee must conduct only those activities approved in DMS.
c. Follow Guidance. Designees must follow all requirements found in regulations, orders, and other guidance related to the functions they perform.
d. Maintain Skills and Knowledge. Designees must maintain technical skill and knowledge of subject matter specific to the designation held.
e. Exhibit Sound Judgment. Designees must display sound judgment.
f. Exhibit Integrity. Designees must show a high degree of integrity, responsibility, and professionalism.
Note: Any designee conduct that casts doubt on the designee’s judgment, integrity, or character at any time could lead to an investigation and be grounds for termination. Refer to Chapter 9, paragraph 4(b)(1) of this Order for additional detail on FAA-initiated “for cause” termination.
g. Report Criminal Charges. All individual designees authorized to act on behalf of the Administrator must report in writing any arrest, indictment, or conviction for violation of local, state, or Federal law to their MS within 30 days of such arrest, indictment, or conviction.
(1) Upon receipt of the reported criminal charges, the MS must suspend the designee and initiate an investigation to determine the appropriate course of action.
(2) Follow-on actions, to include termination or removal of suspension, must be completed in a timely manner based on the results of the investigation.
(3) Managing Offices will forward all individual designee reports of arrests, indictments, and convictions and the results of the Managing Office investigation to the Organization Designation Authorization (ODA) Office (AVS-60) at 9-AWA-AVS-Designee- [email protected].
3. Ongoing Requirements. In addition to maintaining minimum qualifications as specified in this and the designee type-specific volumes, all designees must continue to meet the following requirements:
Chapter 5. Responsibilities and Obligations of a Designee › 4. Other.
a. Use DMS. Designees must use DMS as directed in this order. Designees have the responsibility to read and respond to DMS messages and provide requested information within DMS, as directed, in a timely manner.
b. Maintain Contact Information. Designees must update their DMS profile when changes occur and review their profile at least annually.
c. Access to Internet. Designees must have access to DMS and email through the internet.
(1) The designee is responsible for accessing DMS and checking DMS messages, notifications, and email on a regular and recurring basis.
(2) The designee is responsible for scanning and uploading documents required for designation.
d. Attend Required Training. Designees must comply with minimum training requirements.
e. Attend Required Meetings. Designees must comply with meeting requirements.
4. Other. Designees must maintain other requirements deemed necessary by the appointing office.
2. General. › c. Oversight and DMS. The FAA uses DMS to record the outcomes of…
Chapter 6. Oversight and Management of a Designee
1. Purpose. This chapter describes the common policy associated with the oversight and management of a designee. This chapter and the corresponding designation type-specific volumes constitute the policy for oversight and management of a designee.
2. General.
a. Oversight Principles.
(1) Promote Safety. A primary responsibility of the FAA is to promote safety through systematic oversight of industry stakeholders, including designees. Information generated from oversight programs permits the FAA to identify safety hazards, mitigate risk, and enhance aviation safety. In order for oversight programs to be effective, they must be carefully planned and executed during the conduct of specific inspection activities.
(2) Evaluate Performance. The objective of an oversight program is to ensure that the designee performs to the standards and expectations set forth by the FAA in its policies and regulations. Oversight is not merely an isolated event or series of activities. Oversight results should be considered in total to provide a high-level perspective of a designee’s performance over time.
b. Managing Office and MS.
(1) Designation Type. Designees have a managing office and MS for each designation type. If the designee holds more than one type of designation, a designee may have more than one managing office and more than one MS.
(2) Area of Responsibility. The FAA expects designees to perform a sufficient number of their functions within the bounds of their managing office’s area of responsibility to support required oversight, unless otherwise noted in the designee type-specific volume.
(3) Regulatory Oversight Responsibility. MSs have regulatory oversight responsibility of designees and must monitor them to ensure that they continue to meet the requirements of their designations. A comprehensive oversight plan enables MSs to:
(a) Determine the designee’s compliance with regulatory requirements, guidance, policy, and safe operating practices;
(b) Validate any corrective actions;
(c) Detect changes as they occur in the operational environment; and
(d) Detect the need for regulatory, managerial, and operational changes.
c. Oversight and DMS. The FAA uses DMS to record the outcomes of oversight activities for a designee which may vary depending on the designee type. By documenting oversight activity in DMS, the FAA can make an overall assessment of the designee’s performance.
Chapter 6. Oversight and Management of a Designee › 3. Oversight Actions.
(1) Oversight Characteristics. In DMS, oversight activities have the following characteristics:
(a) A definite beginning and a definite end;
(b) Defined procedures;
(c) Specific objectives; and
(d) A required report of findings.
(2) DMS Oversight and Management Activities. The following activities are available in DMS for most designee types:
(a) Direct observation;
(b) Counseling;
(c) Record feedback;
(d) Training record;
(e) Overall performance evaluation (OPE).
(f) Suspend; and
(g) Terminate.
d. Performance Measures. For many of the oversight activities, the MS should use the following performance measures to determine designee performance:
(1) Technical. The designee demonstrates sufficient knowledge, skill, and ability to conduct authorized tasks within established guidance and standards. The designee possesses an expert level of knowledge and skill, understands and uses appropriate terminology, uses the correct equipment, applies appropriate standards, and accurately interprets results.
(2) Procedural. The designee demonstrates the ability to complete administrative functions correctly. The designee accurately completes and issues appropriate documentation, submits required data, follows established procedures, and complies with all regulations, orders, and directives.
(3) Professional. The designee conducts activities in an ethical, courteous, and conscientious manner reflecting highly on the Administrator. The designee presents a cooperative attitude and demonstrates integrity, tact, and diplomacy when dealing with industry and the FAA. The designee communicates effectively in a manner that reflects positively on the FAA, both orally and written.
3. Oversight Actions. MSs may use DMS to plan but must use DMS to document the outcome of oversight activities.
d. Overall Performance Evaluation (OPE). In addition to normally… › (4) Unless otherwise noted in the designee type-specific volumes, if…
a. Planning an Oversight Activity. DMS allows MSs to plan and record oversight activities.
(1) MSs should use risk management principles when planning oversight.
(2) MSs should review the designee’s previous oversight outcomes as well as current activities, records, and policy as part of the planning.
b. Oversight Activity. For a list and explanation of oversight activities applicable to a specific designee type, see Chapter 6, Oversight and Management of a Designee, in the respective designee type-specific volume.
c. Outcomes of Oversight Activities.
(1) For some oversight activities, the MS must select from three general categories in DMS for the overall ranking of the oversight activity: Satisfactory, Needs Improvement, and Unsatisfactory. If the designee’s oversight outcome results in “Needs Improvement” or “Unsatisfactory,” the MS must enter descriptive text in the appropriate performance measure category(ies).
(2) Additionally, if the designee’s oversight outcome results in “Needs Improvement” or “Unsatisfactory,” the MS must also determine and record appropriate follow-up action(s). For more detail on follow-up actions, see Table 1-2, Overall Performance Result, and Paragraph 4, Follow-up Actions, in this chapter, as well as the performance evaluation information in Chapter 6 of each designee type-specific volume.
d. Overall Performance Evaluation (OPE). In addition to normally scheduled oversight, MSs will complete an assessment of the designee’s OPE over a set period of time by reviewing the designee’s record in DMS.
(1) MSs should perform at least one OPE within the first year after initial designee appointment. After that the schedule is set by the MS. See Chapter 6 in the respective designee type-specific volumes for more information.
(2) During each OPE period, the MS conducts a consolidated review of the designee’s documented oversight activity and other data available in DMS.
(3) Based on an analysis of the information and considering risk-based elements, the MS selects an OPE rating (Satisfactory, Unsatisfactory, or Needs Improvement) and any follow-up actions, if required. See Table 1-2 below.
(4) Unless otherwise noted in the designee type-specific volumes, if the OPE rating is “Needs Improvement” or “Unsatisfactory,” the next performance evaluation must be completed within 6 calendar months from the previous performance evaluation date. If the performance evaluation result is “Satisfactory,” the due date for the next performance evaluation is between 12 and 36 calendar months.
Chapter 6. Oversight and Management of a Designee › 4. Designee Management Functions.
(5) If the OPE rating requires a 6-month follow-up, the next performance evaluation of the designee must be a “Satisfactory” rating or MS must follow the process for terminating the designee described in Chapter 9.
Table 1-2. Overall Performance Result
Overall Performance Result The MS will choose the overall rating that best represents the overall performance result of the designee during the performance period:
Overall Rating Required Action Against
Designee Authority Follow-up Actions Performance Evaluation Required within 6 Months?* Satisfactory None None No
Needs Improvement
See designee type-specific volume, as applicable
Plan and execute an oversight activity
Yes
Unsatisfactory
Suspend* Plan and execute a corrective action activity
Yes
Reduce/Restrict Authority Change authority, plan
and execute oversight activity
Yes
Terminate Terminate N/A * Requires description of planned follow-up activity.
e. Follow-up Actions. Depending on the issues involved, additional follow-up or oversight may be needed to ensure that the deficiency has been corrected. The intent of the follow-up action is to correct the deficiency using the most appropriate method. The following options are available to provide support for designee management:
Note: If suspension or termination is required, please see the designee typespecific “Suspension of a Designation” and “Termination of a Designation” chapters for more information. For “Reduce Authority” decisions, see subparagraph 5b below.
f. Counseling. MSs may use counseling as a type of corrective action to follow up from a specific event, an oversight activity, or to address specific performance issues. The MS must record the results of the counseling session in DMS.
g. Additional Training.
(1) MSs may prescribe additional training to correct a deficiency related to a specific event, an oversight activity, or to address specific performance issues.
(2) If the deficiency is such that the designee is unable to perform authorized functions correctly, the MS may initiate the suspension process to suspend the designation or specific authority until the designee completes the training.
4. Designee Management Functions. Designee management includes the comprehensive evaluation, oversight, and monitoring of a designee’s activities. DMS provides a group of
c. Investigations. The FAA may determine an investigation of a designee… › (1) Reports of alleged misconduct must be submitted through the FAA…
management functions designed to manage the designee’s authorities, limitations, performance and conduct throughout the lifecycle of the designee.
a. Request for Additional Authorizations or Limitations.
(1) Authorities can be expanded and limitations changed on an existing designation only.
(2) When designees believe that they are qualified to perform additional authorized tasks within their designee type, other than those that the FAA currently authorizes, they may request the change through DMS.
Note: In some cases, the MS may also initiate this process in DMS.
(3) The appointing official (AO) must approve all requests for additional authorizations or limitations in DMS. In order for the AO to approve the request, the designee must meet all requirements, and the FAA must have the need and ability to manage the designee. In some cases, an evaluation panel will be convened to review the designee’s qualifications for the additional authorizations. Refer to the designee type-specific volumes for specific instructions.
(4) If approved, DMS will automatically update the authority and CLOA as appropriate, notifying both the designee and the MS. A designee will not exercise any expanded authority until the request has been approved and official notification has been made.
b. Reduce Authority. A MS may initiate a reduction in a designee’s authority for a specific designation through DMS, or a designee can request a reduction of authority through the MS.
(1) DMS requires the MS to enter a justification for reducing a designee’s authority.
(2) In order for the request to be approved, the FAA must consider whether the need and ability to manage the designation still exists given the reduction in authority. If there is no longer a need or ability to manage the designee with reduced authority, the MS will initiate the termination (not for cause) process.
(3) An AO must approve all requests to reduce authority in DMS. If approved, DMS will automatically update the designee’s authorities and CLOA, as appropriate.
c. Investigations. The FAA may determine an investigation of a designee is warranted. Investigations can be initiated based on information discovered during oversight, internal or external feedback, complaints, allegations of misconduct, inappropriate behavior, misuse of authority granted to a designee or other matters the FAA becomes aware of warranting further investigation. This may include investigating actions not directly related to a designee’s activity, but raise questions or concerns about the designee’s ability to continue to act as a Representative of the Administrator. If termination for cause is a possible outcome, the MS will initiate an investigation to determine the appropriate course of action.
(1) Reports of alleged misconduct must be submitted through the FAA Hotline in accordance with FAA Order 1070.1 (as revised), FAA Hotline Program.
(5) Results of the Investigation. › (a) No Action Required.
Note: Investigations as defined in this policy are intended to address issues with designee performance or conduct and are not related to investigations as defined in FAA Order 2150.3 (as revised), FAA Compliance and Enforcement Program.
(2) Purpose. The purpose of the investigation is to determine the appropriate outcome through analysis and assessment. Successful completion will result in a decision on the appropriate management action(s) related to the designee.
(3) Investigation Process. The investigation process may vary depending on designee type. Refer to each designee type-specific volume for additional guidance. At a minimum, the investigation will include the following elements:
(a) The reason(s) for the investigation, to include any complaints or allegations.
(b) Collection of evidence related to the investigation.
(c) A review of the facts and circumstances surrounding the case.
(d) A review of the designee’s record in DMS and any relevant background information in the appropriate FAA databases to determine if there is a pattern of inappropriate behavior or misconduct.
(e) If the FAA notifies the designee of the investigation and the designee chooses to respond, a review of the designee’s response and any documentation provided by the designee.
(f) A decision on the appropriate course of action based on the results of the investigation.
(g) Recording the results in DMS, to include at a minimum:
1. The specific reason(s) for the decision;
2. Any additional designee management actions taken;
3. The designee’s response, if any; and
4. Any associated documentation.
(4) Suspension During an Investigation. The MS may suspend a designee during an investigation depending on the type of designation and authority the designee holds. Refer to each designee type-specific volume for more information.
(5) Results of the Investigation. Based on the outcome of the investigation, the MS will recommend to the AO one of three courses of action in DMS to resolve the investigation:
(a) No Action Required. If the investigation reveals no further action is required, the MS will document the outcome in DMS. If the designee is under suspension, the MS will remove the suspension.
(b) Additional Action Required. If the investigation reveals additional action is required such as counseling, corrective action, training or additional oversight, the MS will document the outcome in DMS and initiate the additional action(s).
(3) Types of feedback or interactions that should be recorded in DMS… › (a) Corrective—intended to correct an error;
(c) Termination of a Designation. If the investigation reveals termination of the designation is warranted, the MS will begin the termination process immediately. If terminating for cause, the AO will initiate a termination for cause review panel as outlined in Chapter 9 of this volume.
(6) Suspected Criminal Activity. If the investigation reveals suspected criminal activity, the MSs will consult with their management for referral to the appropriate Law Enforcement Agency.
d. Inquiries. The FAA will provide support to any official inquiries by other government agencies regarding a designee. An inquiry could result in an FAA investigation.
e. Record Note. MSs can create a personal note or reminder in DMS. This note is the digital equivalent of a sticky note; it is not part of the designee’s official record, and only the author can view the note. MSs should not use this feature to record performance-related issues or other oversight-related information.
f. Send Message to Designee.
(1) MSs can use DMS to send a message to one or more of their assigned designees.
(2) DMS will store the message and record the date the message is sent, along with the date the message is opened by the designee.
(3) DMS users can view these messages. Designees are required to monitor DMS for new messages.
g. Record Feedback or an Interaction Regarding a Designee.
(1) Interaction can be verbal or written communication between the designee, FAA, and industry.
(2) Feedback should be provided promptly following the activity to which it references. While the MS has management responsibility for the designee, any FAA employee working with a designee or designee’s work product has the responsibility to provide feedback regarding the designee’s performance or activity. Any FAA employee with access to DMS can enter feedback on a designee. If the user providing the feedback is not the MS, DMS will send a notification to the MS.
(3) Types of feedback or interactions that should be recorded in DMS include, but are not limited to, the following:
(a) Corrective—intended to correct an error;
(3) Types of feedback or interactions that should be recorded in DMS… › (d) Compliments, critiques, and suggestions.
(b) Evaluative—intended to detail specific positive feedback;
(c) Instructional—intended to provide information about the quality of performance; and
(d) Compliments, critiques, and suggestions.
Chapter 7. Training
1. Purpose. This chapter describes the common policy associated with training of designee applicants, designees, and FAA personnel. This chapter and the corresponding designation type-specific volumes constitute the policy for training.
Chapter 7. Training › 5. Other FAA Employee Training Requirements.
2. General. Designees and FAA personnel must develop and maintain the technical skills, knowledge, ability, and proficiency to effectively perform their duties and roles.
3. Designee Training Requirements.
a. Initial Training. Prior to the FAA appointing an individual as a designee, the individual must participate in and successfully complete the initial training program.
b. Recurrent Training. A designee must regularly attend and successfully complete recurrent training.
c. Specialized Training. Specialized training covers specific authority not held by the majority of designees of a particular type, or covers new concepts, processes, and delegation authority. These topics are not normally covered in the initial or recurrent training for those designee types and are therefore addressed outside of this normal training environment. Specialized training is typically web-based and addresses those areas where specialized experience and authority is required. Where applicable, a designee must complete any specialized training that is required for the specific authority requested or held. This specialized training must be completed prior to appointment or adding the special authority and in some cases must be repeated at the interval specified.
4. FAA Managing Specialist Training Requirements. MSs should complete relevant initial training prior to being assigned as an MS. If an individual cannot complete the relevant initial training prior to being assigned as an MS, they should enroll in relevant training that takes place within 6 calendar months of assignment. The managing office may assign another MS (either from the managing office or another office) to manage the designee(s) until the desired MS completes training.
5. Other FAA Employee Training Requirements. Managers of DMS users who have assigned DMS roles should complete AVS training associated with designee management within 6 calendar months of being assigned that role.
Chapter 8. Annual Request for Extension of a Designee’s Designation › 5. Termination—Nonsubmittal.
Chapter 8. Annual Request for Extension of a Designee’s Designation
1. Purpose. This chapter describes the common policy associated with the FAA’s extension of a designee’s designation from the current expiration date. This chapter and the corresponding designation type-specific volumes constitute the policy for extending a designee’s expiration date.
2. General. Extension of the designee’s expiration date is the responsibility of the designee. Since designee oversight requirements have defined intervals, extension of a designation is not contingent upon completion of a particular oversight activity. As long as a designee is in good standing and continues to meet the requirements of the designation, the designee will be given a one-year extension of their expiration date upon completion of the annual request to extend expiration date action in DMS.
3. Annual Request to Extend Expiration Date.
a. Timeframe. The action item to extend the expiration date will appear on the designee’s home page 60 days prior to the expiration date. If a designee does not complete the action item in DMS prior to the expiration date, DMS changes the designee’s status to “expired.” Designees in an expired status are no longer authorized to perform any duties related to the expired designation and will have limited access to DMS. The designee can return to an active status by completing the action item.
b. Extension Workflow. The extension workflow in DMS requires the designee to verify basic designation information such as designee location, personal profile, and the eligibility requirements to maintain the specific designation. Additionally, the designee must:
• Be in good standing; • Have no violation history; • Be current on all required training; • Have no arrests or convictions; and • Have not had an airman certificate (other than medical), rating, or authorization (or foreign equivalent) suspended or revoked; or have not had to pay a civil penalty as a result of a violation of any FAA or other CAA regulations (foreign or domestic).
4. Updated Expiration Date. Once the annual request to extend the expiration date has been successfully submitted, the expiration date will be extended 12 months to the last day of the month.
Note: Designees in a suspended status may qualify for extension of the expiration date, but they must be in an active status in order to submit the annual request to extend expiration date.
5. Termination—Nonsubmittal. If a designee fails to submit the annual request to extend expiration date, the FAA will initiate the termination process. See Chapter 9 for additional information. Designees terminated for nonsubmittal of an extension are considered terminated “not for cause” and may reapply or be reinstated where designee-specific policy allows.
Chapter 8. Annual Request for Extension of a Designee’s Designation › 10. Disqualifiers.
6. Reminders. The designee is responsible for accessing DMS on a regular basis to check DMS message center notifications and action required items. The designee has the sole responsibility to extend their expiration date upon receipt of the action item in DMS.
7. Surrender. A designee who does not intend to extend a designation is encouraged to voluntarily surrender the designation in DMS prior to expiration.
8. Expansion of Authority. The designee may not seek an expansion of authority using the expiration date extension process. See Chapter 6, Subparagraph 4a, Request for Additional Authorizations or Limitations.
9. Privilege, Not a Right. During the annual request to extend expiration date, the designee will acknowledge that the designation is a privilege, not a right, and the FAA Administrator can terminate the designation at any time, for any reason.
10. Disqualifiers. See the list in Volume 1, Chapter 2, Application Process.
c. Voluntary Surrender Process. › (2) The MS will review the voluntary surrender request in DMS, ensure…
Chapter 9. Termination of a Designation
1. Purpose. This chapter describes the common policy associated with the termination of a designation. This chapter and the corresponding designation type-specific volumes constitute the policy for termination of a designation.
2. General. There are two methods used to terminate a designation: voluntary surrender and FAA-initiated termination.
3. Voluntary Surrender.
a. Voluntarily Surrendering a Designation. A designee may voluntarily surrender a designation.
(1) Designees must surrender each designation separately. The voluntary surrender process applies only to a single designation at a time.
Note: For a company designee, a company representative may contact the designee’s MS to request voluntary surrender in DMS.
(2) A voluntary surrender of a designation does not preclude the individual from applying to be a designee in the future.
(3) Once DMS notifies a designee of the suspension based on a pending termination for cause action, the designee may not submit a voluntary surrender request in DMS.
b. Possible Reasons for Voluntary Surrender of a Designation.
(1) Retirement;
(2) Employment termination;
(3) Lack of business activity;
(4) Difficulty in meeting requirements;
(5) Dissatisfied with being a designee; or
(6) Personal reasons.
c. Voluntary Surrender Process.
(1) To begin the voluntary surrender process, a designee must submit a voluntary surrender request in DMS.
(2) The MS will review the voluntary surrender request in DMS, ensure the reason for the voluntary surrender is stated, and indicate whether or not the designee is considered in “good standing.” This determination is helpful should the designee choose to reapply at a later date.
(1) For Cause. Examples of “for cause” reasons include: › (f) Other.
(3) DMS will limit access to DMS functionality as appropriate for the designation being terminated. The designee is no longer authorized to perform any duties related to the designation.
4. FAA-Initiated Termination. Designees are selected, appointed, and trained to serve the needs of the FAA in fulfilling its safety mission, allowing the FAA to leverage its resources. Therefore, the FAA can rescind a designation at any time for any reason considered appropriate by the Administrator. Designees who are performing poorly, who are representing the Administrator in a negative manner, or who require excessive resources to manage, must have their designations terminated to ensure continued effectiveness of the designee system.
a. Terminating a Designation.
(1) The FAA must document termination decisions in DMS and include the specific reason(s) for the termination.
(2) When applicable, the FAA should review feedback from individuals who have observed the designee’s activities outside of the designee’s managing office.
(3) Only MSs assigned to the designee can initiate the termination process in DMS.
b. Types of Termination. There are two types of termination: “for cause” and “not for cause.”
(1) For Cause. Examples of “for cause” reasons include:
(a) Performance deficiencies found during oversight activities or identified by other sources;
(b) Lack of integrity (e.g., making false statements, misrepresenting information, failing to disclose pertinent information, exhibiting behavior that reflects poorly on the Administrator, etc.);
(c) Misconduct (e.g., purposefully not following prescribed procedures for gain, participating in unethical or illegal activity, etc.);
(d) Inability to work constructively with the FAA or public (e.g., failure to return phone calls, follow guidance, exhibit a cooperative attitude, etc.);
(e) Improper representation of the FAA (e.g., using designee number for inappropriate purposes, etc.); and
(f) Other. Any other reason that the FAA Administrator considers appropriate.
Note: DMS sends termination notifications to all MSs assigned responsibilities for a given designee. The AO will initiate a termination for cause review panel per subparagraph 4.f. below.
(2) Not For Cause. Examples of “not for cause” reasons include any reason other than “for cause.” A designee terminated not for cause may reapply for designation. A “not for cause” termination is not subject to the investigation and review panel process used in “for cause” terminations. Examples of termination other than “for cause” include:
c. Termination Process. › (1) When it has been determined termination is warranted, the MS should…
(a) Lack of FAA Need.
1. Activity in the office decreased, or is forecasted to decrease, eliminating the need for the designee.
2. The FAA plan for delegated work changed, eliminating the need for the designee.
3. The FAA can support the certification work or need with other existing designees.
(b) FAA is Unable to Manage.
1. The existing and projected office workload does not allow the office to effectively manage the designee.
2. The FAA does not have the ability to provide authorization, testing, or additional training needed for its employees to oversee the designee. Adequate funds (for example, travel allocation) are not available to oversee the designee.
3. FAA staff do not have the technical skills and knowledge to oversee the designee.
(c) Other.
1. Designee no longer meets minimum qualifications;
2. Designee does not meet training requirements;
3. Designee is physically unable to perform designee duties;
4. Designee did not extend designation before expiration;
5. Designee’s authority expired while suspended; or
6. Designee is deceased.
c. Termination Process.
(1) When it has been determined termination is warranted, the MS should begin the process immediately. Termination decisions must be formally documented in DMS, to include the specific reason(s). The AO must approve or deny the termination recommendation in DMS.
(2) Once the termination process has begun, DMS will prevent the designee from conducting new work under the designation being terminated. The status of the designee’s authority will change to “suspended” during the termination process. The designee must immediately cease exercising designee privileges for the designation being terminated.
f. Termination For Cause Review Panel. › (2) The review panel will review the facts and circumstances…
(3) Upon completion of the termination process, the designee’s status will be changed to “terminated.” DMS will send an electronic termination notice to the designee.
d. Termination For Cause Investigation. If termination for cause is a possible outcome, the MS will initiate an investigation to determine the appropriate course of action. See Investigations in Chapter 6 of this volume.
e. Designee Response to Termination For Cause. If the termination for cause investigation determines termination for cause is the appropriate course of action, once the MS initiates the termination for cause process, the designee may respond in DMS. To respond to a possible termination for cause action, the designee must respond in DMS within 15 calendar days of the termination for cause action being initiated.
f. Termination For Cause Review Panel.
(1) During the termination for cause process, the AO will initiate a termination for cause review panel to determine if termination is appropriate. There are two types of panels. Only one panel will be conducted, depending on the designee:
(a) Designee with One Designation. When a designee who only holds one designation is being terminated for cause, the members required for the review panel depend on the specific designee type being terminated. Refer to each designee type-specific volume for instructions.
(b) Designee with Multiple Designations. When a designee with multiple designations is being terminated for cause, the AO associated with the designation from the office that initiated the investigation will establish the review panel to determine if the termination is appropriate and if the additional designation(s) should be terminated. In this case, the review panel will consist of:
1. The AO associated with the designation from the office that initiated the termination process. This individual will be the panel point of contact (POC).
2. Each AO associated with the additional designation(s) that may be terminated.
3. A representative from the associated policy office(s).
(2) The review panel will review the facts and circumstances surrounding the termination for cause decision, including all documentation and the designee’s record in DMS, and provide a recommendation to the AO(s) responsible for making the decision. The review panel will determine the following:
• Was an investigation performed? • Is termination justified?
f. Termination For Cause Review Panel. › (5) The AO will make the decision to either terminate the designee or…
(3) The review panel will complete the review process and submit a recommendation within 45 calendar days of the termination for cause process being initiated.
(4) All documentation associated with the review panel (e.g., outcome, members of the review panel, communication with the designee or the associated office) should be included in the designee’s DMS file.
(5) The AO will make the decision to either terminate the designee or reject the termination and reinstate the designee’s privileges. For a designee with multiple designations, the AO for each designation will determine whether to terminate the designee or reject the termination. Each AO’s decision is final and concludes the process.
3. FAA-Initiated Suspension. › d. Other. Any other reason that the FAA Administrator considers…
Chapter 10. Suspension of a Designation
1. Purpose. This chapter describes the common policy associated with the suspension of a designation. This chapter and the corresponding designation type-specific volumes constitute the policy for suspension of a designation.
2. General. Suspension is a management process that allows the FAA to temporarily remove a designee’s privileges without terminating the designation. If an individual holds multiple designations, suspension of one designation may or may not impact other designations held. The impact of the suspension on other designations, if held, is determined by the respective MS.
a. DMS Actions. During the suspension process, DMS will change the designee’s status to “suspended.” In suspended status, DMS:
(1) Notifies the designee of suspension and denies access to initiate new work for the designation being suspended;
(2) Cancels all previously approved activities, as applicable; and
(3) Allows the designee to submit post-activity entries for up to 7 calendar days after the date of suspension.
b. Designee Action While Suspended. The designee must immediately stop exercising authorized duties for the designation being suspended.
c. Suspension Release. If suspended designees believe they have met all of the requirements to release the suspension, they may submit a suspension release request in DMS.
d. Length of Suspension. Designees will remain in a suspended status until they have corrected the deficiency or until the designation expires. If the deficiency has not been corrected within 180 calendar days of the suspension being initiated, DMS will notify the MS to remove the suspension or initiate termination.
3. FAA-Initiated Suspension. The FAA may suspend a designation for the following reasons:
a. Lapse in Minimum Qualifications. The designee no longer meets the minimum qualifications.
(1) The designee loses a required certificate, rating, or license.
(2) The designee fails to maintain required currency, knowledge or proficiency.
b. Failure to Attend a Required Meeting. The designee fails to attend a required meeting.
c. Poor Performance. The designee demonstrates an unsatisfactory level of performance for the designation.
d. Other. Any other reason that the FAA Administrator considers appropriate.
4. Failure to Maintain Currency with Training Requirements. If a designee fails to maintain their currency with training requirements, they will be suspended until they complete their training.
Chapter 10. Suspension of a Designation › 5. Follow-up Actions.
a. Deadline Passes for Required Training. The designee fails to successfully complete required training within the specified timeframe.
b. Failed Test for Required Training. The designee fails a test that is part of required training, regardless of the due date of that training.
5. Follow-up Actions. The FAA may require the designee to complete certain follow-up actions to remove the suspension. FAA follow-up actions may include additional training, counseling, and requalification. The designee should propose a plan of action and timeline to meet requirements. The MS should follow up with the designee to ensure that any requirements are completed. Based on the results of the follow-up actions, the MS will remove the suspension or initiate termination.
4. Impact of Updates to Information. › b. Additional Information. Additional information can be found in the…
Chapter 11. Other Designee Management Functions
1. Purpose. This chapter describes the common policy associated with other designee management functions in DMS. This chapter and the corresponding designation type-specific volumes constitute the policy for other designee management functions in DMS.
2. Assign DMS Roles.
a. General. The primary purpose of this process is to authorize a qualified FAA employee to have appropriate access to functionality within DMS.
(1) DMS roles allow users the ability to access DMS and perform functions within each process, including apply, select, appoint, etc., as described in this order. DMS roles control specific user access within DMS. The FAA may assign users more than one role within DMS.
(2) DMS roles are assigned based on the office needs and in accordance with the designation type-specific volumes of this order.
(3) The term “DMS role” does not convey an official position or title.
b. Master Role Assigner (MRA). MRAs ensure FAA personnel are assigned appropriate roles within DMS to carry out assigned duties.
(1) “Designee Applicant” and “Designee” are roles but are not assigned via the MRA process. DMS automatically assigns designee roles during the appointment process.
(2) The MRA function may be given at different levels within each service or office. It is the responsibility of the MRA to add roles for their office or remove roles for individuals who have moved offices, retired, or no longer need a role in DMS.
3. DMS Message Center. DMS provides a method to send messages between the MS and the designee through the message center.
4. Impact of Updates to Information. Depending on the designation type, updates to certain information in the designee record, such as a change in designation location or qualifications, may affect the designation.
a. Change of Designation Location. A change of designation location may cause the FAA to review need and ability to manage considerations. DMS will notify the current MS if there has been a change of physical address, and the MS will determine if the new address will initiate a change in the managing office. A change in designation location may require the FAA to initiate a designee transfer to the new location.
Note: The FAA is under no obligation to transfer the designee to a new overseeing office.
b. Additional Information. Additional information can be found in the appropriate type-specific volumes for guidance on the types of changes and their impact.
Chapter 11. Other Designee Management Functions › 6. Document Upload.
5. Designee Records.
a. DMS Electronic Records. Once a designee is appointed in DMS, DMS becomes the electronic system of record for all designee information.
b. Prior Designee Records. The FAA must maintain any records associated with the designee prior to appointment in DMS in accordance with the recordkeeping requirements of FAA Order 1350.14.
6. Document Upload. DMS provides the ability to upload documents in support of designee management functions. This capability should not be used to upload designee files associated with the designee prior to DMS appointment.
Chapter 12. Administrative Information › 2. Directive Feedback Information.
Chapter 12. Administrative Information
1. Distribution. This order will be distributed to:
a. The division level within AAM, including the Civil Aerospace Medical Institute (CAMI) and Regional Flight Surgeons (RFS).
b. The division level within FS; all Flight Standards District Offices (FSDO), Certificate Management Offices (CMO), and International Field Offices (IFO).
c. The Washington Headquarters (HQ) branch levels within AIR; all responsible AIR offices; all Certification Branches; the Integrated Certificate Management Division (AIR-500); Policy & Standards Division (AIR-600); the Compliance & Airworthiness Division (AIR-700); the System Oversight Division (AIR-800); Certificate Management Branches (CMBs), and Certificate Management Section (CMS).
d. The division level within the AOV.
e. The Office of the Chief Counsel (AGC).
f. The FAA Academy branches.
g. All individual designees.
2. Directive Feedback Information. For your convenience, you may use FAA Form 1320-19, Directive Feedback Information (which is found on the last page of this order), to submit suggested changes or comments. Please use the “Other Comments” block on FAA Form 1320-19 to provide a complete explanation of why the suggested change is necessary. You may correct, as necessary, a copy of the pertinent policy language, or provide a handwritten note for consideration.
Chapter 1. Introduction › 2. Audience.
VOLUME 2. AME DESIGNEE POLICY
Chapter 1. Introduction
1. Purpose of This Volume. This volume supplements the common designee policy by providing specific guidance for the administration of the Aviation Medical Examiner (AME) designee management program not otherwise given in detail in the common designee policy.
2. Audience. The primary audience of this volume is the Manager/Appointing Official (MGR/AO) of the Aerospace Medical Education Division (AMED), Regional Flight Surgeons/Appointing Officials (RFS/AO), AME Program Analysts/Managing Specialists (AME PA/MS), AME Surveillance Program Analysts (SPA), and AMEs.
a. Minimum Qualifications. Applicants for designation as an AME must: › (6) Be thoroughly familiar with instructions as to techniques of…
Chapter 2. Application Process
1. Purpose. This chapter provides the policy related to the application of AME designees. This designation type-specific policy and Volume 1, Common Designee Policy, constitute the overall policy for an individual applying for designation authority.
2. General.
a. Application Information.
(1) Candidates for initial designation as an AME must submit an application through the DMS.
(2) Contact information for RFSs is located on the FAA website at https://www.faa.gov/pilots/medical_certification/rfs.
(3) The FAA advises all AME applicants to read the selection information in this chapter to ensure that they meet all of the selection criteria before applying for designation as an AME.
b. Multiple Site Authorizations. The RFS/AO may approve, upon request, two authorized work locations within reasonable proximity to one another and within the same region, as appropriate. If a third designation location is desired, within the same region, it must be approved by the senior RFS. Locations in multiple regions are not permitted.
c. Special Considerations. The RFS may give special consideration for designation to those applicants who are pilots, have been military flight surgeons, have special training expertise in aviation medicine, or were previously designated, but have relocated to a new geographic area.
3. Minimum Qualifications.
a. Minimum Qualifications. Applicants for designation as an AME must:
(1) Be in good standing and possess a Doctor of Medicine (M.D.) or Doctor of Osteopathic Medicine (D.O.) degree from an accredited university.
(2) All applicants (foreign and domestic) must possess a current and unrestricted license to fully practice medicine in the state.
(3) Demonstrate past professional performance and personal conduct suitable for a position of responsibility and trust.
(4) Be able to read, write, speak, and understand the English language.
(5) Be knowledgeable of the principles of aerospace medicine.
(6) Be thoroughly familiar with instructions as to techniques of examination, medical assessment, and certification of airmen.
c. Credentials. At the time of initial application for designation, the… › (6) An official government-issued identification with a photograph of…
(7) Abide by the policies, rules, and regulations of the FAA.
b. Methods for Seeking Designees. The FAA expects that all AAM physicians will proactively seek qualified AME applicants using all available forums to advertise needs, requirements, and the application process, including:
(1) Aerospace Medical Association or other aerospace medicine meetings;
(2) Briefings to military flight surgeons and aerospace medicine residency groups;
(3) The FAA AAM website:
https://www.faa.gov/about/office_org/headquarters_offices/avs/offices/aam;
(4) The FAA AME Designee Information website:
https://www.faa.gov/other_visit/aviation_industry/designees_delegations/designee_typ es; and
(5) Social Media and Web Services.
c. Credentials. At the time of initial application for designation, the physician must submit to DMS the following documents or copies (translated into English if in another language):
(1) Medical school diploma.
(2) Certificate of any postgraduate professional training (e.g., internship, residency, fellowship).
(3) Certificate of Good Standing by all medical licensing bodies from which the applicant has active medical licenses, proving there are no restrictions or limitations to practice medicine. This requirement is for international applicants only.
(a) These may be obtained by the region in written form or electronically, or the regional office may request the applicant instruct the licensing body to send certifications to the regional office.
(b) Under no circumstances should a Certificate in Good Standing be accepted directly from the applicant.
(4) Notice of certification by an American specialty board, if applicable.
(5) A current curriculum vitae.
(6) An official government-issued identification with a photograph of the applicant, the applicant’s signature, and the applicant’s residential address, if different from mailing address. This information may be presented in more than one form of identification.
Chapter 2. Application Process › 7. Maintaining an Active Designee Application.
4. Disqualifiers. The FAA will disqualify an AME applicant for certain personal or professional deficiencies and intentional misrepresentations, including:
a. False Statements. In connection with completion of FAA Form 8500-8, AMEs are subject to Title 18 of the United States Code (18 U.S.C.) §§ 1001 and 3571, which indicate that whoever in any matter within the jurisdiction of any department or agency of the United States knowingly and willfully falsifies, conceals, or covers up by any trick, scheme, or device a material fact, or who makes any false, fictitious, or fraudulent statements or representations, or entry, may be fined up to $250,000 or imprisoned not more than 5 years, or both
b. Medical License History. Any past or present adverse action against the medical license of the AME is subject to review by the RFS for suitability or selection.
5. Privilege, Not a Right. See Volume 1.
6. Post-Application. See Volume 1.
7. Maintaining an Active Designee Application. All AMEs or prospective AMEs must immediately update their record in DMS when there is a change in status of licensure to practice medicine or adverse action or warning issued by a state licensing authority.
Chapter 3. Selection and Evaluation of a Designee Applicant
5. Selection & Evaluation. › b. Selection Panel. The evaluation panel consists of an RFS/AO or…
1. Purpose. This chapter provides the policy related to the selection and evaluation of an AME designee applicant. This designation type-specific policy and Volume 1 constitute the overall policy for the selection and evaluation of an AME applicant.
2. General.
a. Selection Process. The general process of selection consists of three steps: DMS determines if system-defined minimum qualifications are met; the selecting official (SO) determines if need and ability requirements are met; and an MS is then assigned to further review the applicant’s qualifications and abilities.
b. Selection Considerations.
(1) DMS is the sole source from which to obtain a list of qualified applicants.
(2) An evaluation panel, determined by the SO, will then be established to review and evaluate the list of viable applicants identified through DMS.
Continue reading ↓ 120 of 1101 passages shown