Order 8130.2K Airworthiness Certification of Aircraft
As summarized in table 1-1 of this chapter, this order establishes policies and procedures for issuing: a. FAA Form 8100-2, Standard Airworthiness Certificate. b. FAA Form 8130-7, Special Airworthiness Certificate. c. Special flight authorizations (SFA). d. FAA Form 8130-4, Export Certificate of Airworthiness (export C of A). e. This order is used with FAA Order 8130.34, Airworthiness Certification of Unmanned Aircraft Systems and Optionally Piloted Aircraft.
This document is cancelled. Cancelled by 8130.2L. Check the official source before relying on it.
U.S. DEPARTMENT OF TRANSPORTATION
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
ORDER
8130.2K
08/28/2024 National Policy
SUBJ: Airworthiness Certification of Aircraft
This order establishes policies and procedures for issuing airworthiness certificates, export certificates of airworthiness, and special flight authorizations for aircraft. This order applies to Federal Aviation Administration (FAA) aviation safety inspectors and certain persons designated to act as representatives of the FAA.
Digitally signed by DANIEL J. DANIEL J. ELGAS Date: 2024.08.28 ELGAS 15:41:49 -04'00' Daniel J. Elgas Director, Policy and Standards Division Aircraft Certification Service
Distribution: Electronic Initiated By: AIR-632
Table of Contents
ii
Table of Contents
Paragraph Page
Table of Contents … ii
List of Tables … x
List of Figures … xi
Chapter 1. Introduction … 1-1
1-1. Purpose of This Order … 1-1
1-2. Audience … 1-1
1-3. Where Can I Find This Order? … 1-1
1-4. Showing and Finding … 1-1
1-5. Aircraft Located Outside the United States … 1-1
1-6. Cross Utilization … 1-1
1-7. Explanation of Policy Changes … 1-2
1-8. Cancellation … 1-2
1-9. FAA Forms … 1-2
1-10. Acronyms, Definitions, and Related Publications … 1-2
1-11. Conflicts … 1-2
1-12. Effective Date … 1-2
Chapter 2. Common Policies and Procedures for Issuing an Airworthiness Certificate … 2-1
2-1. Introduction … 2-1
2-2. Persons Authorized to Issue an Airworthiness Certificate … 2-1
2-3. Common Procedures for Issuing an Airworthiness Certificate … 2-2
2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers … 2-9
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) … 3-1
3-1. Introduction … 3-1
3-2. Common Requirements for Reviewing Aircraft Records … 3-1
3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)) … 3-1
3-4. New Aircraft Manufactured Under a TC Only (§ 21.183(b)) … 3-2
3-5. New Import Aircraft, Foreign SOM (§ 21.183(c)) … 3-2
3-6. Used Aircraft (§ 21.183(d)) … 3-2
3-7. Manned Free Balloons … 3-3
Table of Contents (Continued)
Paragraph Page
iii
Chapter 4. Issuing Special Airworthiness Certificates … 4-1
Section 1. General … 4-1
4-1. Introduction … 4-1
4-2. Common Procedures for Issuing a Special Airworthiness Certificate … 4-2
4-3. Flight Operations Outside the United States … 4-2
4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores … 4-2
Section 2. Experimental Certificates … 4-3
4-5. Introduction … 4-3
4-6. Common Procedures for Issuing an Experimental Certificate (§ 21.191) … 4-3
4-7. Flight Test Areas … 4-4
4-8. Multipurpose Experimental Airworthiness Certificates … 4-6
4-9. PC Holder’s or Modifier’s Procedure for Operating Experimental Aircraft … 4-7
4-10. Former-Military Aircraft Operated for Experimental Purposes … 4-8
4-11. Flight Operations in Reduced Vertical Separation Minimum (RVSM) Airspace. 4-11
4-12. Pioneer Era Aircraft … 4-11
Chapter 5. Primary Category (§ 21.184) … 5-1
5-1. Introduction … 5-1
5-2. General Requirements … 5-1
5-3. New Aircraft Manufactured Under a PC (§ 21.184(a)) … 5-1
5-4. New Imported Aircraft (§ 21.184(b)) … 5-1
5-5. Aircraft Having a Current Standard Airworthiness Certificate (§ 21.184(c)) … 5-1
5-6. Other Aircraft (§ 21.184(d)) … 5-2
Chapter 6. Restricted Category (§ 21.185) … 6-1
6-1. Introduction … 6-1
6-2. Common Requirements … 6-1
Table of Contents (Continued)
Paragraph Page
iv
6-3. New Aircraft Manufactured as Restricted Category (§ 21.185(a)) … 6-1
6-4. Surplus Military Aircraft of a U.S. Armed Force (§ 21.185(b)) … 6-1
6-5. Aircraft Previously TC’d in Another Category (§ 21.185(b)) … 6-2
6-6. Recurrent Certificates for Restricted Category Aircraft (§ 21.185(b)) … 6-2
6-7. Import Aircraft (§ 21.185(c)) … 6-2
Chapter 7. Multiple Certificates for Restricted Category Aircraft (§ 21.187) … 7-1
7-1. Introduction … 7-1
7-2. Procedures for Issuing Multiple Airworthiness Certificates for an Aircraft … 7-1
Chapter 8. Limited Category (§ 21.189) … 8-1
8-1. Introduction … 8-1
8-2. Procedures for Issuing an Airworthiness Certificate … 8-1
Chapter 9. Light-Sport Category Aircraft (§ 21.190) … 9-1
9-1. Introduction … 9-1
9-2. General … 9-1
9-3. Procedures for Issuing an Airworthiness Certificate … 9-2
9-4. Changing From Experimental Purpose to Light-Sport Category … 9-7
Chapter 10. Experimental Purposes of R&D and Showing Compliance § 21.191(a) and (b))10-1
10-1. Introduction … 10-1
10-2. Procedures for Issuing an Airworthiness Certificate … 10-1
10-3. Holding an Airworthiness Certificate in Suspension … 10-1
Chapter 11. Experimental Purpose of Crew Training (§ 21.191(c)) … 11-1
11-1. Introduction … 11-1
11-2. Procedures for Issuing an Airworthiness Certificate … 11-1
Chapter 12. Experimental Purpose of Exhibition (§ 21.191(d)) … 12-1
12-1. Introduction … 12-1
12-2. Procedures for Issuing Airworthiness Certificates … 12-1
Table of Contents (Continued)
Paragraph Page
v
Chapter 13. Experimental Purpose of Air Racing (§ 21.191(e)) … 13-1
13-1. Introduction … 13-1
13-2. Procedures for Issuing Airworthiness Certificates … 13-1
Chapter 14. Experimental Purposes of Market Surveys, Sales Demonstrations, and Customer Crew Training (§§ 21.191(f) and 21.195) … 14-1
14-1. Introduction … 14-1
14-2. Procedures for Issuing an Airworthiness Certificate … 14-1
14-3. Reducing Flight Hour Requirements of § 21.195(d)(2) … 14-1
Chapter 15. Experimental Purpose of Operating Amateur-Built Aircraft (§ 21.191(g)) … 15-1
15-1. Introduction … 15-1
15-2. General … 15-1
15-3. When Builders or Applicants Contact the FAA … 15-2
15-4. Procedures for Issuing an Airworthiness Certificate … 15-2
Chapter 16. Experimental Purpose for Primary Kit-Built Aircraft (§ 21.191(h)) … 16-1
16-1. Introduction … 16-1
16-2. Procedures for Issuing an Airworthiness Certificate … 16-1
Chapter 17. Experimental Purpose of Operating Light-Sport Aircraft (§ 21.191(i)) … 17-1
17-1. Introduction … 17-1
17-2. General … 17-1
17-3. Procedures for Issuing an Airworthiness Certificate … 17-2
Chapter 18. Special Flight Permits (§ 21.197) … 18-1
Section 1. Common Policies and Procedures … 18-1
18-1. Introduction … 18-1
18-2. Who May Issue an SFP? … 18-1
18-3. Purposes … 18-2
18-4. Procedures … 18-3
Table of Contents (Continued)
Paragraph Page
vi
Section 2. Additional Policies and Procedures for Particular Purposes … 18-6
18-5. Production Flight Testing of Aircraft Produced under a TC/PC … 18-6
18-6. Production Flight Testing LSA … 18-7
18-7. Conducting Customer Demonstration Flights … 18-9
18-8. Operation of Overweight Aircraft … 18-10
18-9. Aircraft to Which § 91.409(e) Is Applicable … 18-13
Chapter 19. Provisional Airworthiness Certificates (14 CFR Part 21, Subpart I) … 19-1
19-1. Introduction … 19-1
19-2. Procedures for Issuing an Airworthiness Certificate … 19-1
Chapter 20. Import Aircraft … 20-1
20-1. Introduction … 20-1
20-2. Civil Aviation Authority (CAA) Assistance with U.S. Airworthiness Certificates for New Aircraft Manufactured Outside the United States … 20-1
20-3. Export Certificate of Airworthiness (Export C of A) … 20-1
20-4. Procedures for Issuing an Airworthiness Certificate … 20-3
20-5. Aircraft with Mandatory Continuing Airworthiness Information (MCAI) … 20-6
Chapter 21. Issuing an Export Certificate of Airworthiness (§ 21.329) … 21-1
21-1. Introduction … 21-1
21-2. Procedures for Issuing an Export C of A … 21-1
21-3. Unassembled Aircraft … 21-4
21-4. Approval of Alterations … 21-5
21-5. Multiple Categories … 21-5
21-6. Replacement and Correction of FAA Form 8130-4 … 21-5
Chapter 22. Special Flight Authorizations for Foreign Civil Aircraft (§ 91.715) … 22-1
22-1. Introduction … 22-1
22-2. Eligibility … 22-1
22-3. Procedures … 22-2
Table of Contents (Continued)
Paragraph Page
vii
Chapter 23. Other Policies and Procedures … 23-1
23-1. Introduction … 23-1
23-2. Public Aircraft Operations (PAO) … 23-1
23-3. Production Flight Testing of Aircraft Built Under Military Contract … 23-1
23-4. Operation of Civil Aircraft with a Door Open or Removed … 23-1
23-5. Replacement ID Plates … 23-2
23-6. New Aircraft Manufactured Under § 21.6(b) … 23-3
Chapter 24. Administrative Information … 24-1
24-1. Distribution … 24-1
24-2. Authority to Change This Order … 24-1
24-3. Deviations … 24-1
24-4. Suggestions for Improvements … 24-1
24-5. Records Management … 24-1
Table of Contents (Continued)
Paragraph Page
viii
Appendix A. Completing and Reviewing FAA Forms … A-1
Section 1. General Procedures … A-1
A-1. General … A-1
Section 2. Application for U.S. Airworthiness Certificate … A-2
A-2. Completion of FAA Form 8130-6, Application for U.S. Airworthiness Certificate.A-2
Section 3. Standard Airworthiness Certificate … A-3
A-3. Completion of FAA Form 8100-2, Standard Airworthiness Certificate … A-3
Section 4. Special Airworthiness Certificate … A-6
A-4. Completion of FAA Form 8130-7, Special Airworthiness Certificate … A-6
Section 5. Light-Sport Aircraft Statement of Compliance … A-11
A-5. Reviewing FAA Form 8130-15, Light-Sport Aircraft Statement of Compliance. A-11
Section 6. Application for Export Certificate of Airworthiness … A-23
A-6. Reviewing FAA Form 8130-1, Application for Export C of A … A-23
Section 7. Export Certificate of Airworthiness … A-24
A-7. Completion of FAA Form 8130-4, Export Certificate of Airworthiness … A-24
Appendix B. Documents for Review and Forwarding … B-1
B-1. Introduction … B-1
B-2. Airworthiness Certification Files … B-1
B-3. Review Certification Files … B-1
B-4. Forward Certification Files to AFB-710 … B-2
Appendix C. Program Letters … C-1
C-1. General … C-1
C-2. Program Letter Content … C-1
C-3. Aircraft That Could Perform Public or Military Aircraft Operations … C-4
Appendix D. Issuing Operating Limitations with Special Airworthiness Certificates … D-1
D-1. Introduction … D-1
D-2. General … D-1
Table of Contents (Continued)
Paragraph Page
ix
D-3. Phased Operating Limitations … D-1
D-4. Procedures for Creating Operating Limitations … D-2
D-5. Requests to Add, Modify, or Omit a Limitation, and Required Coordination … D-5
D-6. Review with Applicant … D-6
Appendix E. Civil Aviation Authority (CAA) Assistance with U.S. Airworthiness Certificates for
New Aircraft Manufactured Outside the United States … E-1
E-1. Introduction … E-1
E-2. Applicability … E-1
E-3. Procedure … E-1
Appendix F. Sample Special Flight Authorizations … F-1
Appendix G. Limitations for Operation of an Aircraft with a Door Removed … G-1
Appendix H. Acronyms … H-1
Appendix I. Definitions … I1
Appendix J. Related Publications … J-1
Appendix K. FAA Form 1320-19, Directive Feedback Information … K-1
x
List of Tables
Table Page
Table 1-1. Summary of Airworthiness Regulations, Policies, and Procedures … 1-4
Table 1-2. FAA Forms Completed by the FAA Under This Order … 1-5
List of Tables
Table 8-1. Limited Category TCs … 8-2
Table B-1. Standard Airworthiness Certificates: Documents for Review and Forwarding to the Registry … B-2
Table B-2. Special Airworthiness Certificates: Documents for Review and Forwarding to the Registry … B-5
Table D-1. Operating Limitations … D-8
List of Figures
xi
List of Figures
Figure Page
Figure 2-1. Common Steps for Issuing an Airworthiness Certificate … 2-12
Figure A-1. Sample FAA Form 8100-2, Standard Airworthiness Certificate … A-5
Figure A-2. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Restricted Category Aircraft … A-8
Figure A-3. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Research and Development … A-9
Figure A-4. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Special Flight Permit for Production Flight Test and Customer Demonstration … A-9
Figure A-5. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Light- Sport Category Aircraft Certificated Under § 21.190 … A-10
Figure A-6. Sample FAA Form 8130-7, Special Airworthiness Certificate, for Experimental LSA Certificated Under § 21.191 … A-10
Figure A-7. Sample FAA Form 8130-15, Light-Sport Aircraft Statement of Compliance .. A-21
Figure A-8. Sample FAA Form 8130-15, Light-Sport Kit-Built Aircraft Statement of Compliance … A-22
Figure A-9. Sample FAA Form 8130-4, Export Certificate of Airworthiness … A-27
Figure C-1. Sample R&D/Exhibition/PAO Applicant Program Letter for a Special Airworthiness Certificate … C-5
Figure F-1. Sample SFA for the Flight of an Aircraft to a Place Where Repairs or Alterations Are to Be Made … F-1
Figure F-2. Sample SFA for the Flight of an Aircraft to a New SOR (This Format Is Generally Applicable to a Single Aircraft Authorization for Ferry Flights) … F-3
Figure F-3. Sample SFA for the Purpose of Flight Testing … F-5
Figure F-4. Sample Blanket SFA for Customer Crew Training … F-7
Figure F-5. Sample SFA for Export Delivery … F-9
Figure F-6. Sample Blanket SFA for Delivering Aircraft for the Purpose of Export Delivery … F-11
Figure F-7. Sample SFA for the Purpose of Demonstration … F-12
Figure F-8. Sample SFA for Participating in Aviation Events … F-14
Figure G-1. Sample Limitations for Operation of an Aircraft with a Door Removed … G-1
Chapter 1. Introduction › 1-6. Cross Utilization.
Chapter 1. Introduction
1-1. Purpose of This Order. As summarized in table 1-1 of this chapter, this order establishes policies and procedures for issuing:
a. FAA Form 8100-2, Standard Airworthiness Certificate.
b. FAA Form 8130-7, Special Airworthiness Certificate.
c. Special flight authorizations (SFA).
d. FAA Form 8130-4, Export Certificate of Airworthiness (export C of A).
e. This order is used with FAA Order 8130.34, Airworthiness Certification of Unmanned Aircraft Systems and Optionally Piloted Aircraft.
1-2. Audience. FAA manufacturing and airworthiness aviation safety inspectors (ASI) and certain persons designated to act as representatives of the FAA. Airworthiness ASIs must also refer to FAA Order 8900.1, Flight Standards Information Management System, for related policies and procedures.
1-3. Where Can I Find This Order? You can find this order on the FAA employee website, e FAA public website, and in the FAA Dynamic Regulatory System (DRS). on th
1-4. Showing and Finding. In seeking a certificate or an authorization under this order, an applicant is responsible for presenting evidence necessary to show compliance with applicable requirements; that is, the burden of proof is on the applicant. The FAA is responsible for reviewing and inspecting the applicant’s evidence to make findings of compliance to applicable requirements. If an applicant’s evidence is insufficient to enable the FAA to make its findings, reviews and inspections may be stopped until such time as the applicant presents new evidence to support the FAA’s findings.
1-5. Aircraft Located Outside the United States. Except for issuing an airworthiness certificate under paragraph 20-2 of this order, before processing an application for a certificate under this order for an aircraft located outside the United States, the issuing office must find that the activity can be accomplished without placing an undue burden on FAA resources. Using designees to issue a certificate under this order for an aircraft located outside the United States, would not constitute an undue burden on the FAA but must be authorized in accordance with FAA Order 8000.95, Designee Management Policy.
1-6. Cross Utilization. The FAA performs a variety of functions in issuing certificates and authorization under this order. Many of these functions should be accomplished via coordination among manufacturing, airworthiness, or operations ASIs who have expertise in particular subject matters. Consult with other ASIs as necessary.
Chapter 1. Introduction › 1-12. Effective Date.
1-7. Explanation of Policy Changes. The following changes are included in this revision.
a. This revision incorporates extensive changes throughout the document. Users should perform a complete review of this revision.
b. This revision introduces the use of the Aviation Safety Knowledge Management Environment (ASKME) electronic Airworthiness Certification Application (AWC). Until AWC is updated to reflect the revision of this order, issuance of special airworthiness certificates within AWC will require manually uploading operating limitations from Table D-1 of this order to AWC. Policy changes in this revision that affect AWC may require revision to the application. If a conflict develops between Order 8130.2 and AWC, the order takes precedence. If users are not able to comply with a policy requirement using AWC, users may revert to the paper products or digital equivalent to document and capture data, as well as process and issue certificates as necessary. Users are required to update AWC once the system has been updated to comply with policy.
c. This revision updates office symbols throughout to reflect organizational changes in Aircraft Certification Service (AIR) and Flight Standards.
d. Users must review DRS for applicable issuance of any AIR policy memorandums to ensure they are meeting current national policy.
e. Advisory Circular (AC) Form 8050-72, Export Certificate Number Assignment Card (E-card), is no longer used. FAA Form 8130-4, Export Certificate of Airworthiness, will be revised to remove the block for the E-number.
1-8. Cancellation. The following are cancelled upon the effective date of this order:
a. FAA Order 8130.2J, Airworthiness Certification of Aircraft, dated July 21, 2017, and with Change 1, dated October 27, 2023.
b. All clarification, deviation, and policy memorandums issued for Order 8130.2 before the effective date of this order.
1-9. FAA Forms. Table 1-2 of this chapter lists forms the FAA completes under this order.
1-10. Acronyms, Definitions, and Related Publications. A list of acronyms and definitions are provided in the appendices; see Appendix H and Appendix I, respectively. Additionally, this order references several publications; unless otherwise stated, always refer to the latest revision. See related publications listed in Appendix J.
1-11. Conflicts. If a conflict exists between this order and an applicable bilateral agreement, follow the bilateral agreement.
1-12. Effective Date. This order is effective December 2, 2024.
Table 1-1. Summary of Airworthiness Regulations, Policies, and Procedures
14 CFR Part Airworthiness Certificate Classification / Aircraft Category
Design Standard
Design Approval
Production
Approval
Airworthiness
Certificate
Policy
Standard Airworthiness Certificates for: Normal Utility Acrobatic Commuter Transport Manned free balloons Special classes Airplanes with turbine engines
23, 27 23 23 23 25, 29 31 21.17(b) 34
TC per 21.21/29 PC per 21/G 21.183(a): new under 21/G 21.183(b): new under 21/F 21.183(c): new import, foreign SOM 21.183(d): used & surplus military
Chapter 3
Special Airworthiness Certificates for: Primary Restricted Multiple (Restricted & __ ) Limited Light sport Experimental purpose of: R&D Showing compliance Crew training Exhibition Air racing Market surveys Amateur-built Primary kit-built Experimental LSA SFP (US-registered) Provisional
21.17(f) Varies Varies DOD ASTM N/A
N/A Varies
21.24/29 TC 21.25/29 Varies TC N/A N/A
N/A
TC per 21/C
PC per 21/G Varies Varies N/A N/A N/A
N/A PC per 21/G
21.184 21.185 21.187 21.189 21.190 21.191/3 21.191(a) 21.191(b) 21.191(c) 21.191(d) 21.191(e) 21.191(f)/195 21.191(g) 21.191(h) 21.191(i) 21.197/199 Part 21/subpart I
Chapter 4
Chapter 5 Chapter 6 Chapter 7 Chapter 8 Chapter 9
Chapter 10 Chapter 10 Chapter 11 Chapter 12 Chapter 13 Chapter 14 Chapter 15 Chapter 16 Chapter 17 Chapter 18 Chapter 19 SFA (Foreign-registered) N/A N/A N/A Part 375, 91.715 Chapter 22 Out of Scope of This Order UAS Small UAS (<55#) N/A N/A N/A N/A Part 107
Moored balloons, kites, amateur rockets, & unmanned free balloons
N/A N/A N/A N/A Part 101
Ultralight vehicles N/A N/A N/A N/A Part 103 Limited Recreational UAS N/A N/A N/A N/A 49 U.S. Code § 44809
Public aircraft operations N/A N/A N/A N/A FSIMS Vol 3,
Chapter 14 Commercial space transportation
N/A N/A N/A N/A 14 CFR Chapter III
Table 1-2. FAA Forms Completed by the FAA Under This Order
Form Number Title Source
FAA Form 8100-1 Conformity Inspection Record FAA public website
FAA Form 8100-2 Standard Airworthiness Certificate
ASKME Electronic Airworthiness Certification Application (AWC) or FAA employee website for fillable PDF format
FAA Form 8130-1 Application for Export Certificate of Airworthiness FAA public website
FAA Form 8130-4 Export Certificate of Airworthiness
GPO pad or FAA employee website for fillable PDF format
FAA Form 8130-6 Application for U.S. Airworthiness Certificate
AWC or FAA public website for fillable PDF format
FAA Form 8130-7 Special Airworthiness Certificate
AWC or FAA employee website for fillable PDF format
FAA Form 8130-10 Surplus Military Aircraft Inspection Record FAA public website
Chapter 2. › 2-2. Persons Authorized to Issue an Airworthiness Certificate.
Chapter 2. Common Policies and Procedures for Issuing an Airworthiness
Certificate
2-1. Introduction. This chapter provides common policies and procedures for issuing, amending, exchanging, and replacing standard and special airworthiness certificates. Additional classification-, category-, and purpose-specific procedures for issuing an airworthiness certificate are included in subsequent chapters of this order. This chapter does not apply to issuance of a special flight permit (SFP) except as referenced by chapter 18 of this order.
Note: The procedures for issuing an airworthiness certificate are a combination of the common procedures of this chapter and the applicable classification-, category-, and purpose-specific procedures in subsequent chapters.
2-2. Persons Authorized to Issue an Airworthiness Certificate.
a. ASIs. FAA ASIs are authorized to issue airworthiness certificates.
b. Delegation. The FAA may delegate the issuance of an airworthiness certificate per Title 14 of the Code of Federal Regulations (14 CFR) part 183 and the applicable designee management order.
c. Original and Recurrent Certifications.
Note: Refer to Appendix I of this order for definitions of original and recurrent certification as well as definitions of other terms used throughout this order.
(1) Manufacturing ASIs in the AIR are primarily responsible for original certifications, while airworthiness ASIs in the Flight Standards Service (AFS) are primarily responsible for recurrent certifications. When it is unclear whether a given activity is an original or recurrent certification, the affected offices should coordinate to establish mutual agreement on the responsible office. Manufacturing and airworthiness ASIs may assist each other by mutual agreement.
(2) If a responsible Flight Standards Office receives an application for an original certification, that Flight Standards Office must coordinate with the responsible AIR Certificate Management (CM) section to determine which office will process the application. Similarly, if an AIR CM section receives an application for a recurrent certification, the AIR CM section must coordinate with the responsible Flight Standards Office to determine which office will process the application.
(3) Exceptions to paragraphs 2-2.c(1) and (2) of this chapter:
(a) Any request, original or recurrent, for a special airworthiness certificate for light-sport aircraft (LSA), research and development (R&D), crew training, exhibition, air racing, market survey, amateur-built, or SFP for new aircraft may be handled by a FAA
Chapter 2. › 2-3. Common Procedures for Issuing an Airworthiness Certificate.
manufacturing or airworthiness ASI without further coordination to determine which office will process the application.
(b) Experimental Showing Compliance. Processing an application for an experimental certificate for showing compliance with regulations is the primary responsibility of an AIR CM section. In remote areas or under special circumstances, an AIR CM section may request an airworthiness ASI perform these duties if that person has experience in type certification programs of a type and complexity comparable to the certificate requested.
2-3. Common Procedures for Issuing an Airworthiness Certificate. Common procedures for issuing an airworthiness certificate are illustrated in figure 2-1 of this chapter and specified in this paragraph.
a. The ASKME Airworthiness Certification Application (AWC).
(1) AWC provides an electronic means to process an application for certain certificates and authorizations under this order. ASIs, designees, and ODA unit members must establish an account, process FAA Form 8130-6, and issue standard and special airworthiness certificates using AWC. Unless otherwise stated in this order, all requirements concerning completion of FAA Form 8130-6 must be accomplished in AWC. Advisory Circular 21-12, Application for a U.S. Airworthiness Certificate, provides additional information for using AWC.
(2) Use of AWC by applicants is not mandatory but is the preferred method for application submission. If an applicant is unable or elects not to submit the application in AWC, the FAA will upload to AWC the hard copy of the application from the applicant and transcribe the information to AWC. The ASI must include a statement that the application information was entered on behalf of the applicant. When completing the application on the Documentation- Certification page of AWC, enter the following statement in the SIGNATURE block of Section III, OWNER’S CERTIFICATION: “Application information entered on behalf of the applicant by (Name), (Title). Original attached.” In such cases, do not sign the hard copy or the uploaded application from the applicant, but digitally sign appropriate sections of Form 8130-6 generated by AWC. Per paragraph B-4 of this order, submit both the application signed by the applicant and the AWC-generated application to the FAA Registry (hereafter referred to as Registry).
(3) Access AWC portals as follows. For ASIs, register on the FAA ASI AWC Internet Portal. For Organization Designation Authorization (ODA) unit members and designees, register on the External ODA/Designee AWC Portal; follow prompts for “New User Registration.” Contact the AWC Help Desk at [email protected] for help with access problems.
(4) You may only issue airworthiness certificates and operating limitations outside of AWC in the event of AWC, FAA network, or internet outage. In such cases, revert to the paper process (or portable document format (PDF) equivalent) to document and capture data, process applications, and issue certificates. Once the outage is repaired, upload documents to
AWC that you created offline using the Upload Approval page in AWC and use the comments block to record what you uploaded.
b. Review Application.
(1) A properly completed FAA Form 8130-6, Application for U.S. Airworthiness Certificate, is required to begin the process for issuing an airworthiness certificate. Review FAA Form 8130-6 to verify the applicant completed the form properly. As necessary, refer to FAA AC 21-12, for related guidance.
(2) Letter of Authorization/Agent Letter. If an agent completed the application, verify the registered owner of the aircraft provided a notarized letter of authorization and that the information in this letter is consistent with the application. A true copy of the notarized letter is acceptable.
Note: Requirements and forms of notarization vary among countries.
(3) Type Certificate Data Sheet (TCDS). For an application for an aircraft in a category that requires a type certificate (TC), review the applicable TCDS or aircraft specification to verify the aircraft is eligible for issuance of the requested airworthiness certificate by make, model, and serial number (S/N). An aircraft listing maintained by the responsible certification branch may consist of aircraft model and S/Ns of newly manufactured aircraft that are not yet listed on the TCDS. If none of these documents clearly show the eligibility of the applicant’s aircraft by make, model, and S/N, contact the responsible certification branch to verify eligibility.
Note: DRS contains TCDSs and aircraft specifications. Terms for type certificate data have changed over time including aircraft specifications and TCDS. See the latest version of FAA Order 8110.4, Type Certification, for further information.
c. Review FAA Airworthiness Records on File at the Registry. The requirements in this paragraph also apply to the owner’s information page in AWC.
(1) Current Registration. Access the Registry to verify the aircraft is currently registered per 14 CFR part 47.
(a) Except for paragraphs (b) through (d), the aircraft is registered when an inquiry of the Registry shows that the nationality and aircraft’s registration number (or registration mark) (hereafter referred to as the N-number) is “assigned” and the status is “valid” or “valid-asgn to mfr.”
(b) For a new owner of a used aircraft, lag time in processing the application for registration may result in records of ownership within the Registry database that lag actual transfers in ownership from one United States (U.S.) owner to another. In such cases, the prior owner remains the registered owner of record within the Registry’s database and registration by
the current owner may only be verified as part of the aircraft records review under paragraph 2-3.e.
(c) For a manufacturer temporary N-number, the aircraft is considered registered when an inquiry of the Registry shows that the N-number is “reserved,” and the status is “manufacturer (temp).”
(d) For assignment of a new special registration number, the aircraft is registered when an inquiry of the Registry shows that the N-number is “assigned,” and the status is “valid” or “pending.”
Note1: When searching the Registry for antique or replica aircraft displaying nationality and registration marks as provided for under 14 CFR 45.22(b), omit the inserted symbol allowed by § 45.22(b).
Note2: For a recurrent certification, including previously exported aircraft that are returning to the United States, you may retrieve permanent aircraft records from the Registry using the aircraft make, model, and S/N. For aircraft that do not have a data plate or S/N, you may retrieve records using the N-number or prior N-number for previously exported aircraft returning to the United States.
(2) Prior Denials. Except for new aircraft, check the Electronic Document Retrieval System (EDRS) or order a copy of the aircraft record to determine if the FAA previously issued a denial for this aircraft. If previously denied, verify that the reasons for the denial have been corrected, and record the action taken to clear the denial on the FAA Form 8100-1, Conformity Inspection Record.
d. Identify Potential Safety Hazards. Review available information as necessary to assist you in becoming familiar with the aircraft, aircraft engine, and propeller models and with potential safety hazards. For example, review information as applicable and necessary to understand the manufacturer/builder; configuration; installed equipment; novel or unique features, characteristics, or systems; recent customer findings for new aircraft deliveries; recent quality escapes for new aircraft; histories of service difficulties, incidents, and accidents; ownership history of the aircraft; and potential for degradation from long-term storage. Designees should review the designee alert system for any pertinent information.
Note: The National Transportation Safety Board (NTSB) maintains a searchable database of accidents and incidents involving civil aircraft.
Note: For rotorcraft, review guidance on the Congressional mandate for rotorcraft crash resistant fuel systems. Refer to AIR Memo No. AIR-600-2600-PM04R1.
e. Review Aircraft Records.
(1) Registration. Review the certificate of aircraft registration to verify the aircraft is currently registered and that information on the registration and application match. Note that
the manufacturer’s name may be abbreviated on the application and/or registration. If the registration does not have an expiration date, the registration is not effective. Evidence of aircraft registration may be shown via any of the following [hereafter referred to as registration]:
(a) Aeronautical Center Form 8050-3, Certificate of Aircraft Registration.
(b) Aeronautical Center Form 8050-6, Dealer’s Aircraft Registration Certificate.
(c) Form REGAR-FAX-4, Temporary Certificate of Registration.
(d) Aircraft Registration Application, FAA AC Form 8050-1, under the provisions of § 47.31(c).
(e) A copy of Assignment of Special Registration Number, AC Form 8050-64, along with the current, AC Form 8050-3, Certificate of Aircraft Registration.
(2) Exemptions. For exemptions that the applicant claims to apply to this aircraft, verify each exemption is included in DRS and that each exemption applies to this aircraft make, model, and S/N.
(3) Maintenance Records. Verify the following:
(a) The applicant has all maintenance records required by 14 CFR 91.417.
(b) All maintenance required as of the date you inspect the aircraft is complete, including compliance with applicable airworthiness directives (AD) and applicable aircraft and component life limits.
(c) For used, type-certificated aircraft, that maintenance, preventive maintenance, and alterations were accomplished per 14 CFR part 43.
(4) Weight and Balance. Review the aircraft weight and balance report, including CG limitations, to verify it reflects the current configuration.
(5) Manuals. Verify the applicant has applicable manuals and documents. Applicable manuals and documents may include an aircraft flight manual (AFM), equipment list, FAA-accepted Instructions for Continued Airworthiness (ICA), and FAA-accepted maintenance manual(s). Note that such manuals and documents may not be required for some aircraft certificated under the Civil Air Regulations (CAR).
(6) Flight Testing. Determine if the aircraft has been flight tested if required or as necessary to verify condition for safe operation. As necessary, issue a special airworthiness certificate for showing compliance with the airworthiness regulations (14 CFR 21.127, 21.137(e)(1), 21.189(a)(2), 21.185(d), 21.190(c)(7), and 91.319(b)) per the applicable requirements of this order.
f. Inspect Aircraft. Physically inspect the aircraft to verify−
(1) Nationality, Registration, and Special Marks. The nationality and registration marks meet the requirements of §§ 45.21 through 45.31.
(a) Size. When verifying an N-number is the proper size, verify the height of the marks were measured vertically. The font may be slanted, but do not use the length of the slant line to determine the height of the numbers.
Note: If a surface authorized for displaying required marks under § 45.25 is not large enough for display of full-size marks, § 45.25 allows for marks as large as practicable to be displayed. Assessing “as large as practicable” requires judgment based on the aircraft make/model. For example, for some strongly contoured surfaces, smaller marks may be more legible, and therefore more practicable, than the largest marks that could fit on that surface.
(b) Legibility, Style, Borders, and Shading. The N-number must be legible and written in capital Roman letters without ornamentation. Borders or shading is allowed only if it makes the number more legible. The color of the registration marks must contrast with the background. The N-number must be legible from 500 feet away when viewing it perpendicular to the side of the aircraft during daylight hours.
Note: Section 45.21(b) prohibits a person from placing on any aircraft a design, mark, or symbol that modifies or confuses the N-number. Note this requirement is very broad and includes any feature that would modify or confuse the N-number. For example, N-number paint type, paint color, font type(s), or background patterns must not modify or confuse the N-number.
(c) Display of Foreign Marks for Exporting New Aircraft. Per § 45.31, a person who manufactures an aircraft in the United States for export delivery may display foreign marks on the aircraft as required by the importing state of registry (SOR) of the aircraft while the aircraft is registered in the United States. The manufacturer may operate the aircraft with the foreign marks within the United States for testing, demonstration, or delivery; note these flights are performed under an SFP because the aircraft is registered in the United States.
(d) Marking of certain aircraft with a special airworthiness certificate. When aircraft marks include only the Roman capital letter ‘‘N’’ and the registration number on limited, restricted or light-sport category aircraft or experimental or provisionally certificated aircraft, verify the operator displays on that aircraft near each entrance to the cabin, cockpit, or pilot station, in letters not less than two inches nor more than six inches high, the words ‘‘limited,’’ ‘‘restricted,’’ ‘‘light-sport,’’ ‘‘experimental,’’ or ‘‘provisional,’’ as applicable. Refer to § 45.23.
Note: Although § 45.23 requires these marks “near each entrance to the cabin, cockpit, or pilot station,” this rule does not specify whether these marks must be inside or outside the aircraft; either is acceptable.
(e) Special Marks for Antique or Replica Aircraft. § 45.22(b) provides special marks for exhibition and amateur-built aircraft.
(2) Product Marking.
(a) The aircraft is identified per § 21.182 except for an SFP or an experimental airworthiness certificate not issued for operating amateur-built aircraft, operating primary kit-built aircraft, or operating LSA. Each installed aircraft engine, propeller, propeller blade, and propeller hub manufactured under a TC or production certificate (PC) is marked per § 45.11.
(b) Product identification (ID) plates include the information specified in § 45.13 and must meet § 45.11. Verify the make, model, and serial number (S/N) on the aircraft engine and aircraft propeller product ID plate(s) match the application. Verify the aircraft make, model, and S/N on the aircraft ID plate matches the registration. Note the builder’s name may be abbreviated on the application and/or registration.
Note 1: For aircraft manufactured outside the United States pursuant to a § 21.29 TC, the TC and PC numbers on the ID plate may reflect the foreign design and production approval numbers. The ID plate information should provide a means to determine the applicable U.S. TC number if the TC number of the state of manufacture (SOM) is used.
Note 2: The FAA has, in some cases, granted regulatory exemptions permitting alternate mounting locations of aircraft ID plates for certain aircraft of qualifying air carriers. For any aircraft whose ID plate is mounted in a location other than that which is required in § 45.11, verify this is covered by the provisions of a current regulatory exemption for alternate ID plate location.
(c) When an aircraft has been modified to conform to another make/model, verify the supplemental ID plate contains the information specified in § 45.13. If Aircraft Registration (AFB-710) has not yet issued the new registration with the new model designation, verify that the aircraft make, and the S/N match the application and current registration. If ownership of the aircraft has not changed, an application for aircraft registration, reflecting the new model designation, need not be submitted; AFB-710 will change the model and issue a new registration after receipt of the certification files. Verify the original ID plate has not been altered in any manner.
(d) Inspect the aircraft and review aircraft records to determine whether a violation of §§ 45.13(c) or (e) is apparent. If a violation of §§ 45.13(c) or (e) is found, deny the airworthiness certificate and initiate an enforcement action.
(3) Conformity to TC. For an application for an aircraft in a category that requires a TC, verify the aircraft conforms to its TC. This includes conformity to applicable ADs, major repairs, and major alterations. Verify minor repairs or alterations conform to FAA-accepted data.
(4) Engines, Propellers, and Associated Instruments. Engine(s), propeller(s), and associated instruments operate per the manufacturer’s instructions or other FAA-approved instructions, placards, or flight manual supplements.
(5) Systems. Aircraft systems have been checked for proper operation, including the flight control system and pitot static system, as applicable.
(6) Equipment. Installed equipment is functioning properly, including all equipment on the aircraft equipment list, as applicable.
(7) Instruments and Placards. Instruments and placards are correctly located, installed, and properly marked in the English language. In addition, for those instruments necessary for operation in the U.S. air traffic system, verify that measurements display in standard U.S. units of measure.
(8) Airframe Emergency Parachutes. Verify the aircraft log includes reinspection date for the parachute and associated deployment system components. As applicable, verify that airframe emergency parachutes that are ballistic, assisted, or deployable are properly marked, identified, and within their service dates. Verify aircraft marks clearly identify all explosive devices used in conjunction with ballistic parachutes; marks indicating the aircraft is equipped with explosive devices must be applied externally and be readable from the ground. Verify the aircraft log includes reinspection date for the parachute and associated deployment system components.
(9) Foreign Objects. No foreign objects are present that could pose a safety hazard. For example, foreign objects could include tools, scrap material, or miscellaneous debris.
(10) Airworthiness. The aircraft is airworthy.
g. Document Reviews and Inspections. Document all completed reviews and inspections on FAA Form 8100-1, per the instructions on the form. Verify the applicant corrects all unsatisfactory findings, and document those corrections on FAA Form 8100-1 before issuing an airworthiness certificate.
h. Issue Airworthiness Certificate. If you find the aircraft airworthy and all other requirements are met for the requested certificate:
(1) Complete sections V and VIII of FAA Form 8130-6 per the block-by-block instructions in section 2 of appendix A to this order.
(2) Complete the standard or special airworthiness certificate, as applicable, per the block-by-block instructions in section 3 or 4, respectively, of appendix A to this order. Review the certificate to verify it was completed without error.
(3) Make a maintenance record entry. The following is a satisfactory statement for the maintenance record entry: “I find that this aircraft meets the requirements for the certificate requested and have issued a [standard airworthiness certificate or special airworthiness
Chapter 2. › 2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers.
certificate for the purpose(s) of (enter purpose) and operating limitations] dated … The next inspection is due no later than … [Signature: John Smith, Aviation Safety Inspector, AIR-883].”
(4) Give the completed airworthiness certificate to the applicant. Advise the applicant to display the certificate in the aircraft at the cabin or cockpit entrance so the certificate is legible to passengers or flight crew per § 91.203(b).
Note: In certain circumstances such as replacements and others deemed appropriate by the local office manager, it is permissible to transmit the certificate by email.
i. Issue Letter of Denial.
(1) If, after notifying the applicant of all unsatisfactory findings, the applicant does not correct those findings to your satisfaction in a timely manner, write a letter to the applicant denying issuance of the certificate and stating the reason(s) for the denial. If feasible, identify which steps may be accomplished to meet the certification requirements.
(2) Do not complete sections V and VIII of FAA Form 8130-6.
j. Review Records and Forward to the Registry.
(1) Review your records to verify completeness, accuracy, legibility, and compliance with applicable requirements.
(2) Review and forward certification files per appendix B to this order.
2-4. Amendments, Exchanges, Replacements, Surrenders, and Transfers.
a. Amendment.
(1) Eligibility. An airworthiness certificate may be amended when there is—
(a) A change in the aircraft model specified on an airworthiness certificate.
(b) An alteration to the aircraft, such as one that has been approved by a supplemental type certificate (STC) or amended TC, that changes the category of the aircraft specified in block 4 of the standard airworthiness certificate.
(c) A change in the operating limitations for an aircraft with a special airworthiness certificate.
(2) Procedures for Amending an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.e of this order is not required. Review aircraft records as necessary in consideration of the reason for the amendment.
(b) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.f of this order is not required. Inspect the aircraft as necessary in consideration of the reason for the amendment.
Note: In amending a special airworthiness certificate, all operating limitations must be issued per the current version of this order; appendix D, table D-1.
b. Exchange.
(1) Eligibility. Owners that hold a current FAA Form 1362A, Certificate of Airworthiness, FAA Form 1362B, Certificate of Airworthiness, or unexpired Form ACA-1362, Certificate of Airworthiness, may apply for FAA Form 8100-2, Standard Airworthiness Certificate, or FAA Form 8130-7, Special Airworthiness Certificate, as applicable.
(2) Procedures for Exchanging an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review Application. The existing certificate serves as the application; an FAA Form 8130-6 is not required.
(b) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.e of this order is not required. Review aircraft records as necessary to verify the applicant’s request is valid.
(c) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.f of this order is not required. Inspect the aircraft per paragraph 2-3.f(1) and 2-3.f(2)(b) to verify the exterior aircraft N-registration numbers and ID plate information match the application and registration.
c. Replacement.
(1) Eligibility. The FAA may issue a replacement airworthiness certificate when a certificate is declared lost, has been mutilated, is no longer legible, or contains inaccurate and/or erroneous information; or when the aircraft registration number has changed. If the “inaccurate and/or erroneous information” was a result of errors induced or not detected by the assigned inspector (or designee) within 6 months of the most recently submitted airworthiness file, the inspector (or designee) should make the necessary corrections and resubmit the certification file to the Registry. Otherwise, an application or signed statement with a valid reason for a replacement airworthiness certificate must be completed by the applicant to correct the error(s).
(2) Do not issue a replacement airworthiness certificate for the scenarios provided for under paragraph 2-4.a(1) of this order for amending an airworthiness certificate.
Note: Replacing an airworthiness certificate is an administrative function and does not require a finding of airworthiness.
(3) Procedures for Replacing an Airworthiness Certificate. Follow the procedures in paragraph 2-3 of this order except as follows:
(a) Review Application. FAA Form 8130-6 is not required; a signed statement is acceptable. Inspect the signed statement requesting the replacement certificate to verify it is from the registered owner or the operator and includes the aircraft registration number, make, model, and S/N; and a valid reason for replacing the certificate.
(b) Review FAA Airworthiness Records on File at the Registry. A replacement airworthiness certificate may be issued if all the information from the lost or mutilated certificate can be positively established from the maintenance records, from the remains of the certificate, or from the Registry. If there is insufficient data on which to base issuance of the replacement certificate, including the original operating limitations, do not issue the replacement certificate; advise the applicant to apply for a new airworthiness certificate.
(c) Review Aircraft Records. A complete review of aircraft records per paragraph 2-3.e of this order is not required. Review records as necessary to verify the applicant’s request is valid and the aircraft is eligible for the requested airworthiness certificate. When replacing an airworthiness certificate because the aircraft registration number has changed, review both the registration and Aeronautical Center Form 8050-64, Assignment of Special Registration Marks, to verify the aircraft is currently registered and to verify the current N-number.
(d) Inspect Aircraft. A complete aircraft inspection per paragraph 2-3.e of this order is not required. Inspect the aircraft as necessary to verify the applicant’s request is valid and the aircraft is eligible for the requested certificate.
(e) Issue Airworthiness Certificate. When issuing a replacement for a special airworthiness certificate, the operating limitations must match the operating limitations on the original certificate verbatim. Only modifications to the operating limitations for correcting administrative mistakes are allowed. When issuing a replacement for a standard airworthiness certificate that lists an exemption or exemptions in block 5, follow paragraph A-3.e for completing block 5.
d. Surrender. Verify the aircraft owner’s written authorization to surrender the airworthiness certificate states why the certificate is being surrendered. Except for an expired experimental airworthiness certificate, forward the authorization and certificate to AFB-710 for retention in the permanent airworthiness files.
e. Transfer. An airworthiness certificate is transferred with the aircraft (§ 21.179), for example, if there is a change of ownership or transfer of registration.
Chapter 2. › Figure 2-1. Common Steps for Issuing an Airworthiness Certificate
Figure 2-1. Common Steps for Issuing an Airworthiness Certificate
Review application (2.3.b)
Review airworthiness records
on file at the Registry (2.3.c)
Identify potential safety
hazards (2.3.d)
Review aircraft records (2.3.e)
Inspect aircraft (2.3.f)
Document reviews &
inspections (2.3.g)
Issue airworthiness certificate (2.3.h) or letter of denial (2.3.i)
arro
Review records & forward to
the Registry (2.3.j)
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) › 3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)).
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183)
3-1. Introduction. This chapter provides policies and procedures for issuing standard airworthiness certificates under § 21.183 for aircraft in the normal, utility, acrobatic, commuter, or transport category; manned free balloons; and special class aircraft designated by the FAA under § 21.17(b).
3-2. Common Requirements for Reviewing Aircraft Records. In addition to the common requirements for reviewing aircraft records in paragraph 2-3.e of this order, the following requirements also apply to certain airplanes per § 21.183:
Note: This list is not exhaustive. Other requirements may apply and require verification during your review of aircraft records such as § 91.1505, Repair assessment for pressurized fuselages, and § 91.1507, Fuel tank system inspection program.
a. Noise. Per § 21.183(e), for an application for issuance of an original standard airworthiness certificate, review records to verify compliance with the applicable noise requirements of 14 CFR part 36 or part 91, subpart I, as applicable.
b. Emergency Exit. For transport category airplanes manufactured after October 16, 1987, review records to verify compliance with the passenger emergency exit requirements of § 21.183(f).
c. Fuel Venting and Exhaust Emission. Per § 21.183(g), review records to verify compliance with the fuel venting and exhaust emission requirements of part 34.
3-3. New Aircraft Manufactured Under a PC (§ 21.183(a)). Aircraft manufactured under a PC are eligible for the issuance of an airworthiness certificate without further showing in accordance with § 21.183(a). The submission of FAA Form 8130-9 is not required. The FAA may inspect each aircraft to determine conformity with the approved type design. The inspection frequency may be adjusted by the geographic CM section, or CM branch having certificate management responsibility over the certificate holder. Consider the following in adjusting inspection frequencies: recent changes in the aircraft design, the quality system, personnel, and the supply base; and recent customer-identified deficiencies, quality escapes, service difficulties, incidents, and accidents. When inspecting an aircraft, follow the applicable procedures in paragraphs 2-3 and 3-2 and the following:
a. Review Aircraft Records.
(1) Review the PC and the production limitation record (PLR) to verify the holder is authorized to manufacture the applicable aircraft make and model.
(2) Review the manufacturer’s records to verify that quality system procedures have been completed satisfactorily, including production flight testing of the aircraft.
b. Reserved.
3-4. New Aircraft Manufactured Under a TC Only (§ 21.183(b)). Follow the common procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2 of this order and the following:
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) › 3-6. Used Aircraft (§ 21.183(d)).
a. Review Application.
(1) Verify that the manufacturer is still authorized to manufacture under a TC since such authorizations are of limited duration.
(2) Review FAA Form 8130-9, Statement of Conformity, to verify proper completion and to verify the applicant certifies the aircraft is airworthy and was flight tested. Refer to FAA Order 8110.4 for additional information on FAA Form 8130-9.
b. Review Aircraft Records.
(1) Review the FAA’s inspection records for each aircraft to verify that any prior findings have been properly addressed.
(2) Review the manufacturer’s records to verify that any interim quality system procedures have been completed satisfactorily, including production flight testing of the aircraft.
(3) Verify any nonconformities involving material review actions have been resolved through the responsible certification branch before issuance of an airworthiness certificate.
c. Inspect Aircraft. You must inspect each aircraft presented for issuance of a standard airworthiness certificate to find the aircraft airworthy. Adjust inspections as necessary for any significant changes in manufacturing systems, procedures, or personnel, or when changes have been introduced into the aircraft. Inspect the aircraft to verify conformity to its TC, including applicable ADs. This does not imply that every article must be subjected to a conformity inspection. Conformity inspections of articles should only be conducted when, in the FAA’s judgment, conformity cannot be substantiated by any other means.
3-5. New Import Aircraft, Foreign SOM (§ 21.183(c)). Follow the procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2, and chapter 20 of this order.
3-6. Used Aircraft (§ 21.183(d)). This paragraph applies to issuing a standard airworthiness certificate for a used aircraft, including a surplus aircraft of the U.S. Armed Forces. Follow the common procedures for issuing an airworthiness certificate in paragraphs 2-3 and 3-2 of this order and the following:
a. Review Aircraft Records.
(1) Review aircraft maintenance records to verify the aircraft was inspected and found airworthy per § 21.183(d)(2) within 30 days before the date of the application. The rule requires the aircraft to have been inspected per the performance rules for 100-hour inspections in § 43.15, meaning use of a checklist that includes at least the scope and detail of appendix D to
Chapter 3. Issuing Standard Airworthiness Certificates (§ 21.183) › 3-7. Manned Free Balloons.
part 43. In lieu of a 100-hour type inspection, it is acceptable for the aircraft to have been inspected with an equivalent performance standard acceptable to the FAA, such as any inspection program prescribed under § 91.409; if inspected per an approved progressive or continuous airworthiness inspection program, this means all inspections must be current. For aircraft with no manufacturer’s recommended inspection program, the inspection program must be one approved by the FAA. This inspection program must have the equivalent performance standard defined to be eligible for compliance with any aircraft certificate conformity inspection used for issuance of an airworthiness certificate. Verify that one of the following persons performed this inspection and found the aircraft airworthy:
(a) The manufacturer;
(b) The holder of a repair station certificate issued under 14 CFR part 145;
(c) The holder of a mechanic certificate as authorized in 14 CFR part 65; or
(d) The holder of a certificate issued under 14 CFR part 119, and having a maintenance and inspection organization appropriately rated for the type of aircraft involved.
(2) Surplus Aircraft of the U.S. Armed Forces. Review:
(a) FAA Form 8130-31, Statement of Conformity – Military Aircraft, or its predecessor, FAA Form 8130-2, Conformity Certificate – Military Aircraft. This form is issued to a military service at the time of manufacture to identify deviations from the FAA TC for a new, military aircraft that was derived from an FAA, type-certificated aircraft. Verify any deviations have been corrected. Refer to FAA Order 8110.101, Type Certification Procedures For Military Commercial Derivative Aircraft, concerning the use of these forms.
(b) Military maintenance records to determine if operating limitations were exceeded; if so, contact the responsible certification branch for an airworthiness assessment of all exceedances.
(c) Records of engines, gearbox assemblies, landing gear, instruments, or other articles establishing that they originally conformed to the TC and have been maintained per applicable FAA requirements. Military maintenance and/or repair station records may be used for this purpose.
b. Used, Imported Aircraft. For an application for a standard airworthiness certificate for a used, imported aircraft, refer to chapter 20 of this order for additional, related policies and procedures.
3-7. Manned Free Balloons. Follow the applicable procedures for issuing a standard airworthiness certificate in paragraphs 3-3 through 3-6 of this order and the following:
a. Inspect Aircraft. Inspect the aircraft to verify the applicant is presenting a complete aircraft for issuance of a standard airworthiness certificate. For a manned free balloon, a complete aircraft consists of an envelope with an eligible burner, fuel system, and basket; verify the combination is allowed per the TCDS. You may not issue a standard airworthiness certificate for an article only.
b. Delivery of New Envelopes. Manufacturers of manned free balloons may deliver a balloon envelope when the envelope is the only article ordered. A balloon envelope that is manufactured, assembled to a burner and basket, and flight tested is eligible for a standard airworthiness certificate. The envelope, along with the standard airworthiness certificate and the logbook, may be delivered without the burner and basket. The envelope may then be assembled to a different burner and basket per the TC. A person may accomplish the interchange of the burner and basket as a preventive maintenance task as described below.
c. Changing the Burner and Basket. A new airworthiness certificate is not required when the aircraft is disassembled and a different burner and basket combination is installed, as allowed by the TC. Reassembly of the envelope and bottom-end articles into a complete aircraft may be performed as preventive maintenance under 14 CFR part 43, appendix A, paragraph (c)(27). The aircraft records must properly reflect the installation of the bottom-end articles and record the new empty weight. The bottom-end components must be in a current “annual or 100-hour” inspection status. The individual records of the bottom-end articles must be maintained.
d. Replacement Envelopes. If an envelope is provided only as a replacement article without obtaining a new aircraft S/N, registration number, or ID plate, the installation of the replacement envelope is a maintenance item under part 43. This requires appropriate documentation of the work performed and a return to service entry in the aircraft records by a person authorized to perform the maintenance. The aircraft ID plate, S/N, and registration number are carried over from the previous aircraft envelope.
Section 1. General › 4-1. Introduction.
Chapter 4. Issuing Special Airworthiness Certificates
Section 1. General
4-1. Introduction.
a. This section provides common procedures for issuing a special airworthiness certificate. A special airworthiness certificate may be issued for:
(1) Primary. A primary category aircraft under § 21.184.
(2) Restricted. A restricted category aircraft under § 21.185.
(3) Limited. A limited category aircraft under § 21.189.
(4) Provisional. An aircraft that meets part 21, subpart C, Provisional Type Certificates, and subpart I, Provisional Airworthiness Certificates.
(5) Light-Sport. A light-sport category aircraft under § 21.190.
(6) Experimental. An aircraft for an experimental purpose under § 21.191.
(7) Special Flight Permits. An aircraft that does not currently meet applicable airworthiness requirements, but is capable of safe flight, and meets §§ 21.197 and 21.199.
b. Section 2 of this chapter provides common policies and procedures for issuing a special airworthiness certificate for experimental purposes.
c. Additional policies and procedures that are specific to certain aircraft categories, experimental purposes, and for SFPs are provided in subsequent chapters of this order.
d. The following special airworthiness certificates have similar provisions for crew training and for demonstration flights. Note the differences among the scopes of these provisions to ensure you issue the appropriate certificate.
(1) Experimental certificate for crew training under § 21.191(c) is for training the applicant’s flight crews. This normally includes a manufacturer’s employees who need to be trained in experimental aircraft but may also include a company/applicant that operates an experimental aircraft and needs to train its pilots/employees to obtain an appropriate type rating or authorization to serve as pilot in command (PIC) of the aircraft.
(2) Experimental certificate for market survey under § 21.191(f) is for purposes of conducting market surveys, sales demonstrations, and customer crew training only as provided for in § 21.195. Customer crew training is for training the customer’s flight crews.
(3) An SFP under § 21.197(a)(5) is for aircraft manufacturers for conducting customer demonstration flights in new production aircraft that have satisfactorily completed production flight testing.
Section 1. General › 4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores.
(4) An aircraft manufacturer, therefore, could conduct sales/customer demonstration flights as experimental for market survey or with an SFP under § 21.197(a)(5).
4-2. Common Procedures for Issuing a Special Airworthiness Certificate. Except for issuance of an SFP, follow the common procedures in paragraph 2-3 of this order for issuing an airworthiness certificate and appendix D to this order for issuing operating limitations. As applicable, include the systems of paragraph 4-4 in the aircraft inspection.
4-3. Flight Operations Outside the United States. A special airworthiness certificate does not authorize flight operations over a foreign country. However, the FAA may issue the certificate when the applicant intends to operate the aircraft over other countries if the applicant meets requirements for that certificate. A U.S. special airworthiness certificate is often helpful to a civil aviation authority (CAA) when issuing its permission to operate the aircraft in or over its country. If the FAA knows the affected CAA will not permit operation of the aircraft in or over its country, the FAA cannot deny issuance of the certificate if the applicant has met requirements for that certificate. In any case, an ASI should make the applicable CAA(s) aware of the aircraft, its category or experimental purpose, and the operating limitations for the aircraft.
4-4. Aircraft Equipped with Explosive Devices or Jettisonable Stores. These types of systems are usually associated with former-military or certain restricted category aircraft.
a. Maintenance of Jettisonable Stores. Verify that applicant’s inspection program includes maintenance and inspection of jettisonable stores systems per the manufacturer’s procedures.
b. Ejection Seat Systems. Verify the ejection seat system has been approved for use in the aircraft model by the aircraft manufacturer or by a military service using that aircraft model.
c. Procedures for Securing Aircraft. Verify the applicant has provisions and procedures for securing the aircraft whenever the aircraft is parked to prevent inadvertent operations of a system that uses an explosive device.
d. Airport Notification. Verify that applicant has notified the manager of the airport where the aircraft is based concerning the presence of jettisonable stores, any explosive devices, and planned operations of the aircraft from that airport.
e. Marks for Explosive Devices. Verify the applicant clearly marked all explosive devices on the exterior of the aircraft. Marks must clearly indicate that the aircraft is equipped with explosive devices.
Section 2. Experimental Certificates › 4-6.
f. Operations with Jettisonable Stores. Except for certain restricted category aircraft, only aircraft with an experimental certificate for R&D may be operated with a jettisonable store and only for a test that requires jettisoning that store.
Section 2. Experimental Certificates
4-5. Introduction. This section provides common policies and procedures for issuing special airworthiness certificates for experimental purposes.
4-6. Common Procedures for Issuing an Experimental Certificate (§ 21.191). Follow the procedures for issuing an airworthiness certificate in section 1 of this chapter and the following:
a. Review Application.
(1) Verify the program letter meets § 21.193:
(a) Purpose. Ensure the program letter clearly describes how the aircraft will be used and verify the operation meets a § 21.191 purpose. Guidance is contained in appendix C. The use of the same aircraft for overlapping programs is acceptable, and the program letter can outline one or more programs. After showing compliance with § 91.319(b), the aircraft can be used to support other aircraft in the program or other experimental programs the applicant has underway. If applicable, verify such support activities are described in the program letter.
(b) Time. Verify the program letter contains the estimated number of flights or flight hours and the period of calendar time required for the operation.
(c) Area. Verify the program letter defines the specific area over which the aircraft will be operated, including routes to and from specified airports. A written or pictorial description or an aeronautical chart is acceptable. You should consult with an operations ASI, per paragraph 1-6, to ensure suitability of the area.
(d) Drawings or Photographs. Unless converted from a previously type-certificated aircraft without significant change in the external configuration, verify the program letter includes three-view drawings or three-view dimensioned photographs of the aircraft.
(2) Eligibility. Verify the program letter supports the requested experimental purpose and that purpose is one listed in § 21.191. For example, except as provided for under §§ 21.191(f) and 21.195, brokering or marketing of experimental aircraft is not a valid experimental purpose; this includes an individual who manufactures, imports, or assembles an aircraft, and then applies for an experimental airworthiness certificate to help sell the aircraft.
(3) Information for Operating Limitations. Verify the level of detail in the program letter is sufficient to enable the FAA to prescribe all appropriate operating limitations.
Section 2. Experimental Certificates › 4-7. Flight Test Areas.
(4) Multiple Purposes. If the applicant is seeking an experimental certificate for multiple purposes, verify the program letter clearly documents all of the items listed in paragraph 4-6.a(1) of this order separately for each purpose. In addition, verify the program letter describes any required configuration changes for changing purposes, to include adding or removing equipment and enabling or disabling systems; required configuration changes are typically specified via the modification or addition of operating limitations. Configuration changes may also require adjustments to the aircraft inspection program. Refer to paragraph 4-8 of this order for additional policies and procedures concerning multiple experimental purposes.
b. Inspect Aircraft.
(1) Special Aircraft Marks. Inspect the aircraft to verify the aircraft is marked, “Experimental.”
(2) Information to Safeguard the Public. Per § 21.193(c), upon inspecting the aircraft, obtain any pertinent information from the applicant as necessary to safeguard the general public.
4-7. Flight Test Areas.
a. Assigned Flight Test Area.
(1) Section 91.319 requires that an experimental aircraft be assigned to a flight test area until it is shown that the aircraft is controllable throughout its normal range of speeds, is controllable throughout all maneuvers to be executed, and has no hazardous operating characteristics or design features. Per § 91.305, verify the assigned test area includes only open water, or sparsely populated areas, and having light air traffic. Evaluate each application to determine that the flight test area and airports are sufficient to accomplish the program. In some cases, assigning multiple flight test areas and airports may be required to accommodate various aircraft configurations, types of operations, airport facilities, or safety hazards.
(2) Coordinate the applicant’s proposed flight test area with an operations ASI. If no response is received, contact the office manager for assistance. In addition, consider coordinating with the applicable Air Traffic Control (ATC) facilities.
b. Airport Adjacent to Densely Populated Area.
(1) Coordination of Approach/Departure Routes. Before issuing operating limitations for the aircraft, coordinate approach and departure routes with a responsible Flight Standards Office operations ASI that has the geographic responsibility for the applicable airport(s) and flight test area(s). Advise applicants of their responsibility to do the same with the respective ATC facility prior to operations.
(2) Acceptable Approach/Departure Route. In the case of the first flight of an aircraft from an airport adjacent to densely populated areas, but with at least one acceptable approach/departure route that is compliant with § 91.305, ensure a route is selected which
subjects the fewest number of persons and the least property to possible hazards. The description of the area selected by the applicant and agreed to by the FAA must be included in the operating limitations.
Note: An acceptable approach/departure route must comply with § 91.305 and provide a reasonable opportunity to execute an off-airport emergency landing that will not jeopardize other persons or property.
(3) No Acceptable Approach/Departure Route. In the case of an aircraft located at an airport with no acceptable approach/departure route, you may issue the airworthiness certificate that includes an operating limitation that prohibits operations at that airport. Advise the applicant to relocate the aircraft to an airport suitable for flight testing.
c. Aerobatics.
(1) Aerobatic maneuvers may be permitted while the aircraft is in the assigned flight test area if the aircraft has the capability of such flight. However, these maneuvers should not be attempted until sufficient flight experience has been gained to establish that the aircraft is controllable.
(2) Aerobatic maneuvers that have been demonstrated in the assigned flight test area should be documented in the aircraft records. Only those aerobatic maneuvers that have been successfully accomplished should be permitted after leaving the assigned flight test area.
d. Duration of Assignment to the Flight Test Area.
(1) Duration. Judge each program duration based on the type, complexity, and condition of the aircraft and the complexity of the test. For example, flight testing in conjunction with a minor STC alteration may require only one hour in an assigned flight test area while the initial operation of a prototype jet aircraft or a former-military aircraft may require much more time. In some cases, it may be appropriate to specify the duration as completion of the flight test program, not a fixed flight time.
(2) Finding Compliance. You may amend the operating limitations to permit flight outside of the assigned flight test area after the applicant shows and you find compliance with § 91.319(b). Your finding may be based on a statement by the pilot in the aircraft maintenance records that the aircraft is controllable throughout its normal range of speeds and throughout all the maneuvers to be executed and has no hazardous operating characteristics or design features. You may also witness flights or inspect the aircraft if deemed necessary. You may also find compliance based on the FAA-approved procedures of a PC holder or modifier as discussed in paragraph 4-9 of this order. Note that an application is required to amend the airworthiness certificate/operating limitations.
Section 2. Experimental Certificates › 4-8. Multipurpose Experimental Airworthiness Certificates.
e. Phased Operating Limitations. Phased operating limitations are issued for exhibition, air racing, operating amateur-built aircraft, operating primary kit-built aircraft, or operating light-sport aircraft under § 21.191. Phased operating limitations are further discussed in paragraph D-3 of appendix D.
(1) Phase I typically means the initial period of flight testing for an applicant to demonstrate that the aircraft complies with § 91.319(b). For example, Phase I flight testing is required for a newly assembled amateur-built aircraft, newly assembled kit-built LSA, other experimental aircraft that were disassembled and re-assembled, and expansions of flight limitations beyond what was previously demonstrated under Phase I testing. Phase I may also apply to an aircraft that has been in long term storage or following a major alteration.
(2) Phase II means the period after satisfactory completion of phase I testing.
f. Operating Outside Flight Test Areas. Except as provided for in paragraphs 4-9 and D-3 of appendix D to this order, operation of the aircraft outside an assigned flight test area will require issuance of an amended experimental airworthiness certificate with amended operating limitations if Phase II operating limitations were not included with the certificate.
4-8. Multipurpose Experimental Airworthiness Certificates. An experimental airworthiness certificate may be issued for more than one of the purposes under § 21.191. When more than one purpose is requested, verify the operator has adequate procedures for ensuring the aircraft is in condition for safe operation when changing purposes. The issuance of multiple purpose certificates for R&D and showing compliance should be limited to PC holders; this may be extended to modifiers (§ 21.195(c)) when justified. PC holders or modifiers may submit a procedure that meets the requirements of paragraph 4-9 of this order to their geographic responsible FAA office for approval.
Note: Issuing multiple certificates for a restricted category aircraft under § 21.187 is different than issuing an experimental certificate with multiple purposes or issuing multiple experimental certificates for multiple purposes. Issuance of multiple certificates for restricted category aircraft is covered by chapter 7 of this order.
a. Options. Use your discretion in determining the best option for the desired use. Options include issuing multiple certificates, issuing a multipurpose certificate, or not allowing the aircraft to be used for more than one purpose.
b. Configuration Changes. Consider how the aircraft configuration may change and how the operation of the aircraft may change from one purpose to another. This information should be included in the program letter because it may impact the operating limitations issued to the applicant, and/or additional inspections may be required when changing purposes.
Example 1: The holder of an experimental exhibition certificate seeks an experimental R&D certificate for flying as a chase aircraft in support of an R&D project. No alterations to the aircraft are necessary. An applicant
could be allowed to hold both exhibition and R&D certificates. When the R&D project is completed, no further action is required because the applicant still holds the exhibition certificate.
Section 2. Experimental Certificates › 4-9.
Example 2: The holder of an experimental exhibition certificate seeks an experimental R&D certificate to test new sensor technology. The operator will need to appreciably modify the aircraft. The aircraft should only hold the R&D certificate.
Example 3: An applicant for an experimental certificate for operating an amateur-built aircraft mentions they intend to race the aircraft. A single certificate with both purposes listed may be appropriate in this situation.
Note: Configuration changes and operational differences should also be considered if the applicant intends to conduct public or military aircraft operations while holding the experimental certificate.
4-9. PC Holder’s or Modifier’s Procedure for Operating Experimental Aircraft. A PC holder or aircraft modifier who applies regularly for special airworthiness certificates to conduct flight tests following the same procedures may submit its procedures to its geographic responsible FAA office for approval. Coordinate the document review with a local operations inspector. Having an approved procedure benefits the applicant and the FAA with increased standardization, simpler program letters, reduced duplication of coordination among FAA offices, and timelier issuance of airworthiness certificates. After approval, the procedure may be listed in the operating limitations as indicated in appendix D to this order. The FAA may exclude certain aircraft from the privileges of either all or part of this procedure such as the first aircraft of a new model or a non-production R&D aircraft. These procedures must not provide relief from any operation limitation or regulation. The procedure should include the following elements:
a. Flight Test Area. A description of the flight test area that meets paragraph 4-7 of this order.
b. Flight Log. A daily flight log that records completion of pre-flight inspections and compliance with § 91.319(b) for the duration of the certificate.
c. Flights Outside the Test Area. A description of the method used to conduct and record necessary flights outside the test area, and for maintaining these records. This procedure will remain active for the duration of the certificate and will eliminate the need for the PC holder to obtain approval for each flight.
d. Carriage of Persons. A description of the method used to define the persons who may be carried during these flight operations that includes:
(1) A requirement that the PIC advise each person of the experimental nature of the aircraft, per § 91.319(d).
Section 2. Experimental Certificates › 4-10. Former-Military Aircraft Operated for Experimental Purposes.
(2) A method of recording persons carried on each flight for the duration of the certificate.
(3) A provision that no persons may be carried in the aircraft during flight unless that person is required for the purpose of the flight. Persons other than flight crew members may be carried when the following conditions are met:
(a) The aircraft is of the same basic model that previously has shown compliance with §§ 91.319(b) and 21.195.
(b) Flight tests do not include intentional maneuvers involving abrupt changes in the aircraft’s attitude, abnormal attitudes, or abnormal acceleration/deceleration not necessary for normal flight.
(c) The procedures specifically cover the types of flying to be permitted while carrying persons other than flight crew members.
e. Multiple Experimental Purposes. A description of the method used to determine an aircraft is in a condition appropriate for the purpose intended when changing from one experimental purpose to another, including documenting the results of this determination in a maintenance record or daily flight sheet.
f. Carrying the Approved Procedure. A requirement that a copy of the procedures approved under paragraph 4-9 of this order be carried in the aircraft while operating under the privileges of this procedure. A copy of this procedure may also be included or directly referenced in the PC holder’s quality manual for the convenience of the manufacturer and the FAA.
g. Other. Any other procedures deemed necessary in the interest of safety.
h. Approval of this procedure. Review and approval may require the coordination of different offices within the FAA (such as CM sections, responsible Flight Standards Office, the Air Traffic Organization (ATO), the Aircraft Evaluation Division (AED), and outside the agency. This could include airport first responders such as fire departments and security. The FAA office responsible for oversite of the manufacturer is responsible for coordination.
4-10. Former-Military Aircraft Operated for Experimental Purposes.
a. Advising the Applicant. Advise the applicant to review the following FAA ACs.
(1) FAA AC 21-54, Experimental Airworthiness Certification of Certain Former- Military Aircraft.
(2) FAA AC 43-209, Recommended Inspection Procedures for Former Military Aircraft.
b. Eligibility.
(1) If a TC has not been issued for the aircraft, it may be eligible for a special airworthiness certificate for the experimental purpose of R&D, crew training, exhibition, or air racing.
(2) Some aircraft may have high risk factors that may be impractical to mitigate and, consequently, may not be eligible for an airworthiness certificate.
c. Identify Potential Safety Hazards. Given the variety of aircraft types, models, alterations, operational histories, and airworthiness ramifications of possible long-term storage, becoming familiar with former-military aircraft is especially important. Additional considerations for becoming familiar with the aircraft and with potential safety hazards include the following:
(1) Identify the aircraft model and/or series, as well as the type of engine(s), propellers, and other systems installed, as applicable. Obtain as much historical information as possible to include S/Ns, aircraft and component life limits, overhaul dates, airframe cycles, and engine time and cycles.
(2) Review accident and incident data for the aircraft model. Data can be retrieved from the NTSB database of accidents and incidents, the FAA, and other international and military sources.
(3) Review available aircraft type club information.
(4) Review the ownership history of the aircraft. This may provide information on how the aircraft was previously operated and maintained, which may have implications for the airworthiness inspection.
(5) Become familiar with the scope of any restoration, repairs, and maintenance conducted by or for the applicant. It is also helpful to become familiar with the general condition of working/storage areas, availability of spare parts, and equipment before conducting the formal records inspection.
(6) Ensure the operator has a complete set of the applicable military flight, inspection, and maintenance manuals for the aircraft and inspection and maintenance manuals for the engine.
(7) Ensure the operator has applicable military technical orders to address known issues related to airworthiness, maintenance, and servicing.
(8) Identify any high-risk factors associated with the design, manufacture, maintenance, and operation of the aircraft. Verify the applicant adequately mitigates any high-risk factors.
d. Import Documentation for Imported, Former-Military Aircraft.
(1) Records for imported former-military aircraft that may have weapons installed should include the following documents issued by the Department of Justice, Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF):
(a) ATF Form 6, Application and Permit for Importation of Firearms, Ammunition, and Implements of War.
(b) ATF Form 6A, Release and Receipt of Imported Firearms, Ammunition, and Implements of War.
Note: For any questions regarding ATF Forms 6 or 6A, contact the ATF Firearms and Explosives Imports Branch.
(2) A product that was declared as parts, scrap, or for museum display on any documentation related to importing that product is not eligible for an airworthiness certificate. This includes documents issued by or for ATF, Customs and Border Protection, or the Department of State.
e. Demilitarization of Former-Military Aircraft.
(1) Removing or Disabling Systems. The FAA may require that some systems be removed or disabled to establish a condition for safe operation for the intended use. For example, safe operation of guns, cannons, targeting radars, electronic jammers, jettisonable stores (including external store pylons and external fuel tanks), or explosive devices may not be feasible under or consistent with the intended experimental purpose. Potential safety hazards related to these systems include accidental firing of guns, accidental release of stores, accidental operation of radars on the ground, compartment fires, and damage to the airframe. These hazards may pose risks to other aircraft and to persons and property on the ground and may not be able to be adequately mitigated via operating limitations. Although some of these systems may be required to support a valid R&D purpose, the applicant and the FAA need to understand the corresponding safety risks and work closely together to determine the feasibility of mitigating these risks via operating limitations.
(2) Additional Information on Weapons. For additional information on aircraft weapons systems, refer to aircraft maintenance manuals and the related weapons delivery manual. Some aircraft manufacturers may offer guidance on aircraft demilitarization. U.S. Air Force Technical Order 00-80G-1, Make Safe Procedures for Public Static Display, can be used as a reference.
f. Ejection Seats.
(1) An inspection program for operable ejection seats will be based on a current manufacturers or military program and will include replacement intervals for life-limited or shelf-life-limited components such as pyrotechnic cartridges. These limits cannot be extended without the manufacturer’s approval.
Section 2. Experimental Certificates › 4-12. Pioneer Era Aircraft.
(2) The PIC and flight crew operating aircraft equipped with operational ejection seat(s), whether armed or not armed, must have satisfactorily completed an ejection seat training program per FAA AC 91-87, Ejection Seat Training Programs, within the past 24 calendar months prior to operation for this make and model of aircraft. Passengers of these aircraft must have a safety brief prior to flight per FAA AC 91-87.
(3) The PIC and flight crew operating aircraft that were previously issued an operating limitation that required FAA acceptance or approval of an ejection seat training program, meet that operating limitation if they successfully complete training using an ejection seat training program per the FAA AC 91-87 for the applicable aircraft make/model.
(4) For questions concerning specific aircraft and ejection seat training, contact the responsible Flight Standards Office or AFS-830.
g. Drag Chutes. As applicable, verify the drag chute installation records reflect installation per applicable military installation requirements.
4-11. Flight Operations in Reduced Vertical Separation Minimum (RVSM) Airspace. Experimental aircraft that do not meet the requirements of § 91.180(a) may be allowed to operate in RVSM airspace in certain circumstances as described in § 91.180; part 91, appendix G; and the Aeronautical Information Manual. In addition, at the time of the flight, ATC must find the aircraft can be provided appropriate separation and that the flight will not interfere with, or impose a burden on, other approved RVSM operations.
a. Flights for aircraft certification and development purposes may be allowed in RVSM airspace. These flights are typically limited to gathering data to show that the aircraft can meet the minimum standards for the operation in RVSM airspace specified in part 91, appendix G. Further information regarding modifications or alterations that impact RVSM approval can be found in FAA AC 91-85, Authorization of Aircraft and Operators for Flight in Reduced Vertical Separation Minimum (RVSM) Airspace.
b. Aircraft climbing or descending through RVSM flight levels without intermediate level off, to or from flight levels above RVSM airspace, may be accommodated. Obtain data from the operator showing that the aircraft can complete a non-stop climb to flight level 430.
4-12. Pioneer Era Aircraft. Replica, reproduction, restored, and similar aircraft based on aircraft from the pioneer era, before the year 1914, require special consideration. Many of these aircraft have limited maneuverability and are only capable of flying for very short distances. An application for an airworthiness certificate for these aircraft should be coordinated with the Systems Policy Branch (AIR-630) and the General Aviation and Commercial Division (AFS-800) by emailing the coordination mailbox (9-AVS-AIR- [email protected]) to ensure the operating limitations are appropriate for the intended operations.
Chapter 5. Primary Category (§ 21.184) › 5-5.
Chapter 5. Primary Category (§ 21.184)
5-1. Introduction. This chapter provides policies and procedures for issuing a special airworthiness certificate for a primary category aircraft under § 21.184.
5-2. General Requirements. Follow the procedures in chapter 4, section 1 of this order and the following:
a. Review Aircraft Records. Verify that any special inspection and preventive maintenance program for the applicable aircraft make and model was accepted by the FAA as follows:
(1) For airplanes, acceptance by the AED (MKC-AED) with engineering input by the certification branch where TC application was made.
(2) For rotorcraft, acceptance by the AED (FTW-AED) with engineering input by the certification branch where TC application was made.
b. Issue Airworthiness Certificate. Advise the applicant that only a properly qualified pilot/owner may perform preventive maintenance under the special inspection and preventive maintenance program. To be properly qualified, a pilot/owner must successfully complete an FAA-approved course given by an approved aviation maintenance technician school, the holder of the PC for the pilot/owner’s aircraft, or another entity approved by the FAA.
5-3. New Aircraft Manufactured Under a PC (§ 21.184(a)). Follow the procedures in paragraphs 3-3 and 5-2 of this order.
5-4. New Imported Aircraft (§ 21.184(b)). Follow the procedures in paragraph 5-2 and chapter 20 of this order.
5-5. Aircraft Having a Current Standard Airworthiness Certificate (§ 21.184(c)). As provided for under § 21.184(c), an applicant may exchange a current standard airworthiness certificate for a special airworthiness certificate in the primary category if the aircraft meets § 21.24(a)(1). Note that conversion from standard to primary categories allows an owner/pilot to perform preventive maintenance. The conversion will be made via STC. To issue a special airworthiness certificate under § 21.184(c), follow the procedures in paragraph 5-2 of this order and the following:
a. Issue Airworthiness Certificate.
(1) Obtain the standard airworthiness certificate from the applicant.
(2) Advise the applicant that its aircraft cannot be returned to a standard airworthiness certificate without showing that it meets all the requirements for a standard airworthiness certificate as prescribed by the regulations. Such a showing historically has been difficult when an aircraft has remained in a different classification or category for a lengthy
Chapter 5. Primary Category (§ 21.184) › 5-6. Other Aircraft (§ 21.184(d)).
period. To facilitate the return to a standard airworthiness certificate, the aircraft records should indicate, among other requirements, that the aircraft has been maintained according to the manufacturer’s instructions, and that any alterations to the aircraft either were removed or approved by the FAA.
b. Reserved.
5-6. Other Aircraft (§ 21.184(d)). For an application for a special airworthiness certificate in the primary category for an aircraft that meets the criteria of § 21.24(a)(1) and is not covered by paragraphs 5-3, 5-4, or 5-5 of this order, follow the procedures of paragraph 5-2 of this order and the following:
a. Review Aircraft Records. Review applicable records to verify:
(1) The aircraft conforms to an approved primary, normal, utility, or acrobatic type certificate, including compliance with all applicable ADs.
(2) The aircraft has been inspected and found airworthy within the past 12 calendar months per § 91.409(a)(1).
b. Reserved.
Chapter 6. Restricted Category (§ 21.185) › 6-4. Surplus Military Aircraft of a U.S. Armed Force (§ 21.185(b)).
Chapter 6. Restricted Category (§ 21.185)
6-1. Introduction. This chapter provides policies and procedures for issuing a special airworthiness certificate for a restricted category aircraft under § 21.185.
6-2. Common Requirements. Follow the procedures in chapter 4, section 1 of this order and the following:
a. Review Application.
(1) Verify the restricted category operation is indicated in section II, block B.3 of the application. Refer to FAA Order 8110.56, Restricted Category Type Certification, for the current listing of all special purpose operations approved under § 21.25(b)(7).
(2) If an applicant wishes to obtain approval for a new special purpose operation not previously approved under § 21.25(b)(7), refer to FAA Order 8110.56 for guidance in proposing new special purpose operations. Verify the aircraft is type-certificated in the restricted category under § 21.25, CAR 8, or § 21.29 or previously type-certificated in another category and modified for a special purpose.
(3) In the case of an aircraft previously type-certificated in another category and modified for a restricted special purpose operation under § 21.25 or CAR 8, the previously approved TC and the STC or approved data can be considered as the equivalent of a restricted TC. The TC and STC or approved design data should define the design parameters that make up the restricted category TCDS.
(4) Non-U.S.-manufactured aircraft type-certificated in any other category under § 21.29 are not eligible for certification in the restricted category unless the aircraft was issued a new or amended TC under § 21.29 or an STC under § 21.25, and subsequently was modified per the TC or STC. In this instance, § 21.185(b) is the basis for issuing the restricted airworthiness certificate.
(5) Verify the special purpose operation(s) indicated on the application is listed in the TCDS certification basis or approved by an installed STC.
b. Review Aircraft Records. Per § 21.185(d), review records to verify compliance with the applicable noise requirements of part 36.
6-3. New Aircraft Manufactured as Restricted Category (§ 21.185(a)).
a. Under a PC. Follow the procedures in paragraphs 3-3 and 6-2 of this order.
b. Under a TC. Follow the procedures in paragraphs 3-4 and 6-2 of this order.
6-4. Surplus Military Aircraft of a U.S. Armed Force (§ 21.185(b)). Follow the procedures in paragraph 6-2 of this order.
Chapter 6. Restricted Category (§ 21.185) › 6-7. Import Aircraft (§ 21.185(c)).
6-5. Aircraft Previously TC’d in Another Category (§ 21.185(b)). For modified aircraft that were either surplus military aircraft of a U.S. Armed Force or previously type-certificated in another category and modified for a restricted special purpose operation under § 21.25 or CAR 8, the previously approved TC and the STC or approved data can be considered as the equivalent of a restricted TC. The TC and STC or approved design data should define the design parameters that make up the restricted category TCDS. Follow the procedures in paragraph 6-2 of this order, and verify the following:
a. The alteration conforms to the FAA-approved data forming the basis for the restricted TC.
b. The aircraft is in a good state of preservation and repair and is in a condition for safe operation.
6-6. Recurrent Certificates for Restricted Category Aircraft (§ 21.185(b)). Follow the procedures in paragraph 6-2 of this order.
6-7. Import Aircraft (§ 21.185(c)). Follow the procedures in paragraph 6-2 and Chapter 20 of this order.
Chapter 7. › 7-2.
Chapter 7. Multiple Certificates for Restricted Category Aircraft (§ 21.187)
7-1. Introduction. This chapter provides policies and procedures for issuing multiple airworthiness certificates for a restricted category aircraft under § 21.187.
Note: Issuing multiple certificates for a restricted category aircraft under § 21.187 is different than issuing an experimental certificate with multiple purposes or issuing multiple experimental certificates for multiple purposes. Issuance of multiple certificates and a multi-purpose certificate for experimental aircraft is covered by paragraph 4-8 of this order.
7-2. Procedures for Issuing Multiple Airworthiness Certificates for an Aircraft. The procedures for issuing multiple airworthiness certificates are a combination of the procedures covering standard (Chapter 3 of this order) and restricted (Chapter 6 of this order) airworthiness certificates, or limited (Chapter 8 of this order) and restricted airworthiness certificates and the following:
a. Review Application.
(1) Determine if the applicant needs one or more certificates. If an aircraft already holds an eligible airworthiness certificate under § 21.187, it is unnecessary to reissue that certificate when exercising the provisions of § 21.187 for issuance of multiple airworthiness certificates for a restricted category aircraft. Issue only the certificated needed. For example, if the aircraft already holds a standard airworthiness certificate, only issue the restricted category certificate. AWC includes an instructional aid that provides supplemental information on issuance of a special airworthiness certificate while allowing the applicant to retain a current standard airworthiness certificate when applying for multiple certificates for restricted category aircraft.
(2) Verify the aircraft is eligible−
(a) For multiple certificates for the requested aircraft categories. An aircraft in the restricted category may be eligible for multiple airworthiness certificates if it can be converted to the normal, utility, acrobatic, commuter, transport, or limited category by removing or adding equipment by simple mechanical means. This provision does not extend to an aircraft in the primary or light sport category, or to an aircraft issued a certificate for an experimental purpose.
(b) By S/N for both categories according to the applicable TCDSs or STC.
b. Review Aircraft Records. Determine if operations in the restricted category would exceed operating limitations of the other aircraft category. If so, the aircraft may not be eligible for a multiple airworthiness certificate. Any operations outside of the other category operating limitations while operating in the restricted category, unless approved for that aircraft, may make it impossible to return the aircraft to the other category unless a complete engineering evaluation
is made. Therefore, to retain eligibility for return to the other category after being operated in the restricted category, the following applies:
(1) While being operated in the restricted category, any changes made to the aircraft that are to be retained when returning to the other category, or any operations that are outside of the operating limitations of the other category, must be approved per the regulations and procedures applicable to the other category.
(2) If the maximum gross weight and/or operating limitations for the restricted category is/are higher than that for the other category, the aircraft is not eligible for operation in the other category after having been operated in the restricted category unless—
(a) The TCDS specifically states that the aircraft is eligible for operation in the other category after having been operated at the limitations applicable to the restricted category; or
(b) If the TCDS does not have such a note or any other reference, the operations outside of the other category operating limitations including increased gross weights must be FAA-approved.
c. Inspect Aircraft.
(1) Witness the applicant’s method of compliance with §§ 21.187(a)(1) and 21.187(a)(2) and determine if the instructions for converting the aircraft from one category to the other are adequate.
(2) Reserved.
d. Issue Airworthiness Certificate(s).
(1) If the application is for restricted and limited categories, issue FAA Form 8130- 7 with appropriate operating limitations for each category. If the application is for the restricted category and a category in the standard classification, issue FAA Form 8100-2 for the standard classification and FAA Form 8130-7 with appropriate conditions and operating limitations for the restricted category. If the aircraft already holds one of the certificates, only issue the certificate that is needed.
(2) If one of the multiple certificates is a standard airworthiness certificate, and the aircraft will be used for the carriage of passengers for compensation or hire in the standard configuration, evaluate the restricted special purpose operation to determine whether the airworthiness inspection prescribed in § 21.187(b) will be required each time the aircraft is converted from a restricted airworthiness certificate to a standard airworthiness certificate. Normally, if the special purpose operation involves carriage of maximum loads or is subject to contamination by pesticides, herbicides, corrosives or other hazardous materials, the airworthiness inspection must be required and an operating limitation to this effect should be prescribed. In such cases, specify in that operating limitation whether this airworthiness inspection must be conducted by the FAA or an appropriately certificated mechanic.
Chapter 8. Limited Category (§ 21.189) › 8-2. Procedures for Issuing an Airworthiness Certificate.
Chapter 8. Limited Category (§ 21.189)
8-1. Introduction. This chapter provides policies and procedures for issuing a special airworthiness certificate for an aircraft in the limited category under § 21.189.
8-2. Procedures for Issuing an Airworthiness Certificate. Follow the procedures in chapter 4, section 1 of this order and the following:
a. Review Aircraft Records.
(1) Review the TCDS, aircraft specifications, and/or applicable aircraft listing to verify the aircraft is eligible for issuance of a special airworthiness certificate in the limited category. Refer to table 8-1 of this chapter for aircraft makes and models with TCs in the limited category. If you are unsure whether an aircraft is eligible according to its TCDS, contact the responsible office listed in DRS for that TCDS.
(2) Review the aircraft maintenance records to verify the applicant met the § 21.189(a)(2) requirement for flight testing the aircraft. Verify these records include the findings of the flight test and were signed by the pilot who conducted the flight test.
(3) Review available documents, such as military technical orders and inspection records to help you assess the airworthiness of the aircraft.
(4) Look for evidence of long-term storage and inactivity which may impact the scope of your aircraft inspection.
b. Inspect Aircraft.
(1) Because surplus military aircraft may have deteriorated due to prolonged storage, prolonged inactivity, or age, the applicant must show that the aircraft was thoroughly inspected to determine its state of preservation and repair and to ensure it is in a condition for safe operation. The inspection may require removing rivets and cutting openings to check the condition of faying surfaces and closed areas. If this is the case, the applicant should be advised that the inspection would be expedited if an airworthiness inspection is performed by an appropriately rated repair station or mechanic per the requirements of part 43.
(2) Reserved.
Table 8-1. Limited Category TCs
Original Manufacturer TC Holder Model Limited Spec No.
DRS Listing Boeing Transcontinental and Western
B-17F and B-17G AL-1 LTC-1
North American S and R B-25, B-25C, B-25G, B-25H, B-25J, and B-25N
AL-2 AL-2
Douglas P.V. Shields A-26B and A-26C AL-3 TCS L-3 Douglas Seaboard and Western
A-24 (Navy SBD-5) AL-4 TCS L-4
Consolidated Vultee
R.M. Lewis PB2Y-3, PB2Y-3R, PB2Y-5, PB2- 5R, and PB2Y-5Z AL-5 LTC-5
Consolidated Vultee
Consolidated Vultee LB-30 AL-6 LTC-6
Sikorsky Holmes R-4B Helicopter AL-7 LTC-7 Grumman Air Trading Corp TBF-1, TBF-1C, TBM-1, TBM-1C, TBM-3, and TBM-3E
AL-8 LTC-8
Douglas Hughes A-20B, A-20C, A-20G, A-20H, and A-20J
AL-9 TCL-9
Lockheed Lockheed P-38E, P-38J, P-38L, P-38M, F-5E, F-5F, and F-5G
AL-10 LTC-10
North American Cal Pacific P-51C, P-51D, and P-51K AL-11 LTC-11 Beech Cameron AT-10, AT-10BH, AT-10GF, and AT-10GL
AL-12 LTC-12
Lockheed Air Trading Corp B-34, PV-1, and PV-2 AL-13 LTC AL-13 Northrup Northrup P-61, P-61A, and P-61B AL-14 LTC-14 North American Edmondson A-36A AL-15 LTC-15 Curtis Holmberg O-52 AL-16 LTC-16 Grumman Utterback J2F-3, J2F-4, J2F-5, and J2F-6 AL-17 LTC-17 Curtis-Wright Prevost P-40L and P-40N AL-18 LTC-18 Sikorsky Hel-i-cop Advertising R-5A Helicopter AL-19 LTC-19 Martin Krogman PBM-5 AL-20 LTC-20 Bell Aircraft Bell Helicopter Textron
P-63C and P-63E AL-21 LTC-21
North American Mustang Aviation BC-1 AL-22 LTC-22 Grumman Grumman F8F-1 AL-23 LTC-23 Chance-Vought Chance-Vought OS2N-1, OS2U-1, OS2U-2, and OS2U-3
AL-24 LTC-24
Grumman Carlisle FM-1 AL-25 LTC-25 Consolidated Vultee
Executive Airlines L-1, L-1A, L-1B, L-1C, L-1D, L-1E, and L-1F
AL-26 LTC-26
North American Wyatt BT-9, BT-9A, BT-9B, and BT-9C AL-27 LTC-27 Culver Superior PQ-14A, PQ-14B, YPG-14B, YPQ- 14A, and Navy TD2C1 AL-28 LTC-28
Sikorsky Stolp-Adams R-6A and YR-6A, HOS-1 Helicopter
AL-29 LTC-29
Continue reading ↓ 120 of 519 passages shown