Order 8100.15B Organization Designation Authorization Procedures, Including Change 3
This document is cancelled. Cancelled by 8100.15C. Check the official source before relying on it.
Text read by OCR from a scanned file (7 of 319 pages). Check the original, as some words may be misread.
Distribution: Electronic Only Initiated By: AFS-600
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION 8100.15B CHG 3 CHANGE
National Policy Effective Date:
6/15/18
SUBJ: Organization Designation Authorization Procedures
1. Purpose. This change provides for delegation of approval of Aircraft Inspection Programs (AIP) and determining eligibility of previously approved intervals greater than the manufacturer’s inspection intervals for Air Operator Organization Designation Authorization (AO ODA) types.
2. Who This Change Affects. This change affects all offices of the Flight Standards Service and the Aircraft Certification Service (AIR) that manage ODA holders.
3. Explanation of Changes. This change introduces to the Air Operator (AO) ODA Type the approval of 14 CFR part 91, § 91.409(f)(4), Aircraft Inspection Programs and Determining Eligibility Of Previously Approved Intervals Greater Than the Manufacturer’s Inspection Intervals.
4. Effective Date. This change is effective on October 1, 2018. ODA holders must incorporate any needed procedures manual revisions to address the requirements of this change by December 1, 2018.
5. Disposition of Transmittal Paragraph. Retain this transmittal sheet until the directive is cancelled by a new directive.
PAGE CHANGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
Page iii 5/16/13 Pages ii and iii 6/15/18
Page iv 9/6/16
Page vii 2/3/14 Pages vi and vii 6/15/18
Page viii 9/6/16
Pages 2-2 thru 2-5 5/16/13 Pages 2-2 thru 2-6 6/15/18
Page 3-2 5/16/13 Page 3-2 6/15/18
Pages 3-5 and 3-6 5/16/13 Pages 3-5 thru 3-7 6/15/18
ii
Remove Pages Dated Insert Pages Dated
Page 3-13
Page 3-14
Pages 3-15 thru 3-19
5/16/13
2/3/14
9/6/16
Pages 3-14 thru 3-20 6/15/18
Page 4-1 2/3/14 Page 4-1 6/15/18
Page 5-1
Pages 5-2 and 5-3
2/3/14
9/6/16
Pages 5-1 thru 5-3 6/15/18
Page 5-7 9/6/16 Page 5-7 6/15/18
Page 5-8 9/6/16 Page 5-9 6/15/18
Pages 5-12 and 5-13 9/6/16 Pages 5-12 and 5-13 6/15/18
Page 6-1 9/6/16 Page 6-1 6/15/18
Pages 15-1 thru 15-4 5/16/13 Pages 15-1 thru 15-8 6/15/18
Page G-2 2/3/14 Page G-2 6/15/18
Page I-1 5/16/13 Page I-1 6/15/18
6. Administrative Information. You can find this order on the FAA Regulatory and Guidance Library (RGL) website at http://rgl.faa.gov. Ali Bahrami's signatureAssociate Administrator for Aviation Safety
Distribution: Electronic Initiated By: AIR-100
CHANGE
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
ORDER 8100.15B CHG 2 National Policy 09/06/2016
SUBJ: Organization Designation Authorization Procedures
1. Purpose. This change transmits revised pages to Federal Aviation Administration (FAA) Order 8100.15B, Organization Designation Authorization Procedures. Organization Designation Authorization (ODA) is the FAA program for authorizing an organization to act as a representative of the Administrator. This change provides allowances for delegation of noise and emissions functions, standardizes the reasons for FAA project participation, and incorporates various changes outlined in paragraph 3 below.
2. Who This Change Affects. This change affects all offices of the Flight Standards Service (AFS) and the Aircraft Certification Service (AIR) that manage ODA holders.
3. Explanation of Changes. This change―
a. Removes references to the former AIR-200, Production and Airworthiness Division.
b. Makes revisions to accommodate the delegation of findings of compliance for Title 14 of the Code of Federal Regulations (14 CFR) part 34 and part 36.
c. Clarifies ODA unit member (UM) training requirements. Allows for equivalent training to be provided to ODA UMs in lieu of FAA seminars when determined acceptable by AIR-160 or AFS-600.
d. Clarifies Organization Management Team (OMT) training requirements and incorporates new requirements OMT members and personnel participating in ODA inspections to attend audit training and on-line OMT training by December 31, 2017.
e. Updates corrective action processes to align with the Administrator’s compliance and enforcement philosophy and changes to FAA Order 2150.3, FAA Compliance and Enforcement Program.
f. Removes the requirement for ODA holders to provide quarterly reports of ODA inspection unit member training status.
g. Clarifies that 14 CFR part 183 regulatory violations are eligible under the Voluntary Disclosure Reporting Program.
h. Clarifies suspension and termination procedures, including sample memos.
ii
i. Standardizes the reasons for FAA participation in ODA projects.
j. Allows for Type Certification (TC) ODA holders to approve alternative methods of compliance (AMOC) to airworthiness directives (AD) for a number of products operated by a single operator. Also provides for AMOC approvals in areas other than structures, for deviations not relevant to the unsafe condition addressed by the AD.
k. Allows for design approvals to be based on an applicant’s showing of compliance in lieu of specific ODA unit member approvals.
l. Allows for ODA prototype installations at any location determined to be capable by the ODA holder and as required for return to service.
m. Allows for additional supplemental type certificate (STC) and parts manufacturer approval projects to be conducted without submittal of a program notification letter (PNL).
n. Clarifies that an STC ODA holder may approve new, or changed, airworthiness limitations associated with an STC it issues.
o. Allows STC ODA holders to re-issue STCs for correcting administrative errors.
p. Removes limitation on ODA acceptance of instructions for continued airworthiness (ICA) for security-related projects.
q. Clarifies that Major Repair, Major Alteration and Airworthiness (MRA) ODA holders may conduct compliance inspections under function code 12130.
r. Clarifies notification requirements for MRA ODA holders working outside of their geographic boundaries.
s. References the new FAA Form 8110-31, Type Inspection Report.
4. Effective Date. This change is effective on October 7, 2016. ODA holders must incorporate any needed procedures manual revisions to address the requirements of this change by April 8, 2017.
5. Disposition of Transmittal Paragraph. Retain this transmittal sheet until the directive is cancelled by a new directive.
iii
PAGE CHANGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
iv 02/03/2014 iv 09/06/2016
viii 02/03/2014 viii 09/06/2016
3-9 thru 3-11 02/03/2014 3-9 thru 3-11 09/06/2016
3-15 thru 3-19 02/03/2014 & 05/16/2013 3-15 thru 3-19 09/06/2016
4-3 05/16/2013 4-3 09/06/2016
5-2 thru 5-13 02/03/2014 & 05/16/2013 5-2 thru 5-13 09/06/2016
6-1 05/16/2013 6-1 09/06/2016
6-3 thru 6-8 02/03/2014 & 05/16/2013 6-3 thru 6-8 09/06/2016
7-1 thru 7-6 05/16/2013 7-1 thru 7-6 09/06/2016
8-1 05/16/2013 8-1 09/06/2016
8-4 thru 8-27 02/03/2014 & 05/16/2013 8-4 thru 8-30 09/06/2016
9-4 02/03/2014 9-4 09/06/2016
9-6 02/03/2014 9-6 09/06/2016
10-2 05/16/2013 10-2 09/06/2016
11-1 thru 11-2 05/16/2013 11-1 thru 11-2 09/06/2016
11-4 thru 11-24 02/03/2014 & 05/16/2013 11-4 thru 11-26 09/06/2016
12-3 05/16/2013 12-3 09/06/2016
12-6 thru 12-7 05/16/2013 12-6 thru 12-8 09/06/2016
13-4 thru 13-15 05/16/2013 13-4 thru 13-19 09/06/2016
iv
Remove Pages Dated Insert Pages Dated
14-3 thru 14-7 05/16/2013 14-3 thru 14-6 09/06/2016
A-37 thru A-39 09/06/2016
B-9 5/16/2013 B-9 09/06/2016
C-3 05/16/2013 C-3 09/06/2016
C-18 thru C-19 05/16/2013 C-18 thru C-19 09/06/2016
D-2 05/16/2013 D-2 09/06/2016
H-1 05/16/2013 H-1 09/06/2016
6. Administrative Information. You can find this order on the FAA Regulatory and Guidance Library (RGL) website at http://rgl.faa.gov.
Distribution: Electronic Initiated By: AIR-100
CHANGE
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
ORDER 8100.15B CHG 1 National Policy 02/03/2014
SUBJ: Organization Designation Authorization Procedures
1. Purpose. This change transmits revised pages to Order 8100.15B, Organization Designation Authorization Procedures. Organization Designation Authorization (ODA) is the FAA program for authorizing an organization to act as a representative of the Administrator. This change incorporates various program improvements described in paragraph 3 below.
2. Who This Change Affects. This change affects all offices of the Flight Standards Service and the Aircraft Certification Service that manage ODA holders.
3. Explanation of Changes. This change―
a. Revises paragraph 3-9a and appendix B to clarify the types of ODA manual revisions which may be incorporated by the ODA holder without FAA review.
b. Revises paragraph 3-9b to clarify that procedures manual revisions incorporated without any FAA approval must be submitted to the Organization Management Team (OMT) within 30 days after incorporation of the revision.
c. Revises paragraph 3-10c to require certain manufacturing ODA unit members to attend the web-based Recurrent Manufacturing ODA Unit Member course and to require that engineering unit members only attend DER recurrent technical sessions.
d. Revises paragraph 3-13g to require an ODA holder to provide the OMT with contact information for a unit member removed for ODA-related performance.
e. Revises paragraph 3-19 to clarify that ODA holders must submit proposed corrective actions within 30 days of being notified by the OMT.
f. Revises figure 4-1 to remove the requirement for flight standards membership on the evaluation panel and OMT for supplemental type certification ODA (STC ODA).
g. Revises paragraph 5-2a to require the OMT lead to maintain a listing of OMT members.
h. Revises paragraph 5-3a to remove to requirement for AIR-110 coordination of procedures manual revisions.
i. Revises paragraph 5-4 to clarify supervision visit requirements for OMT members.
ii
j. Revises paragraph 5-6d to provide for notification of proposed Designee Information Network (DIN) tracking to a removed unit member whose performance is determined to be misconduct.
k. Revises paragraph 8-3c to allow an ODA holder to be authorized to approve initial airworthiness limitations for turbine engines.
l. Revises paragraphs 8-7 and 11-8 to allow ODA prototype installations at facilities certificated by a foreign airworthiness authority.
m. Revises paragraphs 8-7f and 11-8f to only require OMT coordination with an off-site facility’s principal inspector if there is a question regarding the facility’s experience with the type of alteration being performed.
n. Revises paragraphs 8-3m and 11-3n to clarify that the “Perform Review and Acceptance of ICA” function includes providing concurrence on maintenance aspects of Electronic Wiring Interconnection System (EWIS) ICA.
o. Revises paragraph 8-9d to standardize the type certification ODA (TC ODA) documentation requirements for alternative methods of compliance approvals.
p. Revises paragraphs 8-12, 9-9, and 11-14 to require submittal of airworthiness certification packages to the Aircraft Registration Branch only when required by FAA Order 8130.2.
q. Revises paragraph 9-4 to clarify that PC ODA holders may only perform functions on products or articles manufactured by the ODA holder or in support of its projects.
r. Revises paragraph 11-7a(7) to allow certain STC ODA projects to be completed without submittal of a program notification letter (PNL).
s. Revises paragraph 11-7d to no longer require a “formal” response to a PNL. The requirement to respond to a STC PNL within 30 days has been eliminated.
t. Revises paragraph 12-3c(6) to prohibit MRA ODA units from issuing special flight permits for the purpose of conducting customer demonstration flights in new production aircraft.
u. Revises paragraph 16-5 to require AIR-110 to enter data documenting unit member misconduct into the DIN system.
v. Revises appendix D, Certification Plans, to allow an ODA holder to provide alternative information in lieu of identifying individual unit members on its compliance checklist.
4. Effective Date. This change is effective on March 10, 2014. All changes introduced in this change must be complied with on March 10, 2014 except for item 3o above, which must be complied with by June 10, 2014. ODA holders must submit procedures manual revisions to address the requirements of this change by May 12, 2014.
iii
5. Disposition of Transmittal Paragraph. Retain this transmittal sheet until the directive is cancelled by a new directive.
iv
PAGE CHANGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
v thru vii v thru vii 02/03/2014
3-7 05/16/2013 3-7 02/03/2014
3-9 thru 3-11 05/16/2013 3-9 thru 3-11 02/03/2014
3-14 05/16/2013 3-14 02/03/2014
3-18 thru 3-19 05/16/2013 3-18 thru 3-19 02/03/2014
4-1 05/16/2013 4-1 02/03/2014
5-1 thru 5-3 05/16/2013 5-1 thru 5-3 02/03/2014
5-5 thru 5-13 05/16/2013 5-5 thru 5-13 02/03/2014
6-3 thru 6-4 05/16/2013 6-3 thru 6-4 02/03/2014
6-8 05/16/2013 6-8 02/03/2014
8-2 thru 8-26 05/16/2013 8-2 thru 8-27 02/03/2014
9-3 thru 9-8 05/16/2013 9-3 thru 9-8 02/03/2014
11-3 05/16/2013 11-3 02/03/2014
11-5 05/16/2013 11-5 02/03/2014
11-7 thru 11-23 05/16/2013 11-7 thru 11-24 02/03/2014
12-2 05/16/2013 12-2 02/03/2014
16-2 05/16/2013 16-2 02/03/2014
A-31 thru A-33 05/16/2013 A-31 thru A-33 02/03/2014
B-6 thru B-16 05/16/2013 B-6 thru B-17 02/03/2014
D-1 thru D-2 05/16/2013 D-1 thru D-2 02/03/2014
G-1 thru G-2 05/16/2013 G-1 thru G-2 02/03/2014
v
6. Administrative Information. You can find this order on the FAA Regulatory and Guidance Library (RGL) website at http://rgl.faa.gov.
Dorenda Baker Director, Aircraft Certification Service
5/16/13 8100.15B
Distribution: Electronic Initiated By: AIR-100
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
05/16/2013
SUBJ: Organization Designation Authorization Procedures
This order establishes the procedures, guidance, and limitations of authority that the Federal Aviation Administration (FAA) grants to an organization under the Organization Designation Authorization (ODA) program. If you work for the Aircraft Certification Service or Flight Standards Service and are involved in appointment or oversight of delegated organizations, you must follow these procedures. This order also offers guidance to help designated organizations understand what the FAA may authorize them to do, and the procedures they must follow.
Margaret Gilligan Associate Administrator for Aviation Safety
ii
Table of Contents
Paragraph Page
Chapter 1. Introduction
1-1. Purpose … 1-1 1-2. Audience … 1-1 1-3. Where You Can Find This Order … 1-1 1-4. Explanation of Policy Changes … 1-1 1-5. Effective Date … 1-3 1-6. General … 1-3
Chapter 2. Program Overview
2-1. FAA Appointment of ODAs … 2-1 2-2. Eligibility For ODA … 2-1 2-3. Definition of ODA Holder and ODA Unit … 2-1 2-4. Types of ODAs … 2-1 Figure 2-1. ODA Functions … 2-3 Figure 2-2. Airworthiness Certificate and Approval Functions … 2-4 Figure 2-3. Operational Approval Functions … 2-5 2-5. Multiple ODA Types … 2-5 2-6. Organization Management Team … 2-5 2-7. Applicability of Referenced FAA Procedures … 2-5 2-8. Certification Activity … 2-6
Chapter 3. Qualifications, Responsibilities, and Authority
3-1. Granting an ODA … 3-1 3-2. Reducing Designees … 3-1 3-3. ODA Holder Location … 3-1 3-4. ODA Holder Qualifications … 3-1 3-5. ODA Staff Qualifications … 3-2 3-6. Responsibilities … 3-6 3-7. Memorandum of Understanding … 3-6 3-8. Authority and Functions … 3-7 3-9. Procedures Manual … 3-7 3-10. Training … 3-9 3-11. Duration of Appointments … 3-10 3-12. Continued Eligibility … 3-11 3-13. Selection of ODA Unit Members … 3-11 Figure 3-1. ODA Unit Member Selection Process … 3-13 3-14. Self-Audit … 3-15 3-15. Self-Disclosure … 3-16 3-16. Work Activity Reports … 3-16
iii
Paragraph Page
3-17. Records … 3-16 3-18. Data Review and Service Experience … 3-18 3-19. Corrective Action … 3-19 3-20. Activity Outside The United States … 3-20 3-21. Use of FAA Forms … 3-20 3-22. Inspection Unit Members at Suppliers … 3-20
Chapter 4. Application, Selection, and Appointment
4-1. Pre-Application Communication … 4-1 Figure 4-1. Appointing/Managing Offices … 4-1 4-2. Application … 4-2 4-3. Selection Process … 4-3 4-4. Appointment … 4-6
Chapter 5. Oversight
5-1. Oversight Program … 5-1 5-2. Organization Management Team (OMT) … 5-1 5-3. Supervision Overview … 5-2 5-4. Supervision … 5-5 5-5. Delegated Organization Inspection Program … 5-9 5-6. Corrective Action … 5-9 5-7. Geographic Coordination … 5-12 5-8. ODA Renewal … 5-12
Chapter 6. Delegated Organization Inspection Program
6-1. Inspection Program Overview … 6-1 6-2. Responsibilities … 6-1 6-3. Inspection Scheduling … 6-2 6-4. Inspection Planning … 6-3 6-5. Performing the Inspection … 6-5 6-6. Post-Inspection Activity … 6-7 Figure 6-1. Inspection Dispute Resolution Flow Chart … 6-9
Chapter 7. Suspension and Termination of an ODA
7-1. General … 7-1 7-2. Cause for Suspension or Termination of ODA … 7-1 7-3. Documentation of Suspension or Termination Decisions … 7-2 7-4. Coordination of Suspension or Termination Decisions … 7-2 7-5. Notice of Suspension or Termination … 7-2 7-6. Appeal Procedures … 7-3 7-7. Surrender of Records … 7-4 7-8. Additional Information on Suspension or Termination of AKT ODA … 7-4 7-9. DIN Status … 7-6
iv
Paragraph Page
Chapter 8. Type Certification Functions
8-1. General … 8-1 8-2. Eligibility … 8-1 8-3. Functions … 8-1 8-4. Limitations … 8-3 8-5. Records … 8-4 8-6. Type Certification Programs … 8-5 8-7. Off-Site Project Requirements … 8-14 8-8. Approval of Major Alteration or Major Repair Data … 8-17 8-9. Approvals of AMOCs to AD and AD-Mandated Repairs … 8-18 8-10. Global AMOCs for Revisions to Service Bulletin … 8-22 8-11. Airworthiness Certification … 8-23 8-12. Special Flight Permits … 8-23 8-13. Special Considerations-Military Commercial Derivative Aircraft (MCDA) … 8-23 8-14. Data Approvals Supporting Certification Projects … 8-25 8-15. Procedures Manual Requirements … 8-25
Chapter 9. Production Certification Functions
9-1. General … 9-1 9-2. Eligibility … 9-1 9-3. Functions … 9-1 9-4. Limitations … 9-3 9-5. Records … 9-3 9-6. Production Certificate and PLR Changes … 9-4 9-7. TC/STC Conformity … 9-5 9-8. Airworthiness Certificates … 9-6 9-9. Special Flight Permits … 9-6 9-10. Airworthiness Approvals … 9-6 9-11. Procedures Manual Requirements … 9-7
Chapter 10. Technical Standard Order Authorization Holder Functions
10-1. General … 10-1 10-2. Eligibility … 10-1 10-3. Functions … 10-1 10-4. Limitations … 10-1 10-5. Records … 10-2 10-6. Conformity Functions … 10-2 10-7. Airworthiness Approvals … 10-2 10-8. Procedures Manual Requirements … 10-3
v
Paragraph Page
Chapter 11. Supplemental Type Certification Functions
11-1. General … 11-1 11-2. Eligibility … 11-1 11-3. Functions … 11-1 11-4. Limitations … 11-3 11-5. Records … 11-4 11-6. Alteration Locations … 11-5 11-7. Supplemental Type Certification Programs … 11-5 11-8. Off-Site Project Requirements … 11-17 11-9. Off-Site Prototype Installations on Military Commercial-Derivative Aircraft ... 11-20 11-10. STC Projects Involving Foreign-Registered Aircraft or Foreign State of Design Products … 11-20 11-11. Finding Compliance With Foreign Regulations … 11-21 11-12. Other Approval Functions … 11-21 11-13. Airworthiness Certification … 11-22 11-14. Special Flight Permits … 11-22 11-15. Special Considerations-Military Commercial Derivative Aircraft (MCDA) … 11-23 11-16. Procedures Manual Requirements … 11-24
Chapter 12. Major Repair, Major Alteration, and Airworthiness Functions
12-1. General … 12-1 12-2. Eligibility … 12-1 12-3. Functions … 12-1 12-4. Limitations … 12-3 12-5. Records … 12-3 12-6. Approving Major Alteration or Major Repair Data … 12-4 12-7. Airworthiness Certification … 12-5 12-8. Special Flight Permits … 12-5 12-9. Activity Outside Geographic Area … 12-6 12-10. Procedures Manual Requirements … 12-7
Chapter 13. Parts Manufacturer Approval Functions
13-1. General … 13-1 13-2. Eligibility … 13-1 13-3. Functions … 13-2 13-4. Limitations … 13-4 13-5. Records … 13-4 13-6. PMA Test and Computation Approvals … 13-5 13-7. PMA Approvals Based on Licensing Agreement or STC … 13-12 13-8. Other Approval Functions … 13-15 13-9. Airworthiness Approvals … 13-15 13-10. Conformity Determinations … 13-16
vi
Paragraph Page
13-11. Data Review and Service Experience … 13-16 13-12. Procedures Manual Requirements … 13-16
Chapter 14. Airman Knowledge Testing Functions
14-1. General … 14-1 14-2. Eligibility … 14-1 14-3. Functions … 14-5 14-4. Limitations … 14-5 14-5. Records … 14-6 14-6. Procedures Manual Requirements … 14-6
Chapter 15. Air Operator Certification Functions
15-1. General … 15-1 15-2. Eligibility … 15-1 15-3. Rotorcraft External-Load Operator Certification Functions … 15-1 15-4. Limitations … 15-2 15-5. Records … 15-3 15-6. Certification Programs … 15-5 15-7. Procedures Manual Requirements … 15-5
Chapter 16. Designee Information Network
16-1. Keeping The Designee Information Network Up To Date … 16-1 16-2. Designation Form … 16-1 16-3. ODA Numbers … 16-1 16-4. Status Definitions … 16-1 16-5. DIN Documentation of ODA Unit Member Misconduct … 16-2
Appendix A. Sample Forms and Letters (36 pages)
Figure 1. Sample FAA Form 8100-13, ODA Statement of Qualifications … 1 Figure 2. Sample ODA Application Checklist … 2 Figure 3. Sample ODA Letter of Designation … 3 Figure 4. Sample ODA Denial Letter … 4 Figure 5. Sample FAA Form 8100-9 Used For ODA STC Data Approval … 5 Figure 6. Sample FAA Form 8100-9 Used For ODA TC Data Approval … 6 Figure 7. Sample FAA Form 8100-9 Used For TC ODA Approval In Support of STC … 7 Figure 8. Sample FAA Form 8100-9 Used For TC ODA Repair Data Approval … 8 Figure 9. Sample FAA Form 8100-9 Used For MRA ODA Compliance Finding … 9 Figure 10. Sample Summary Activity Report … 10 Figure 11. Sample FAA Form 8100-11, Statement of Completion … 12 Figure 12. Sample FAA Form 8100-12 Production Limitation Record Report … 13 Figure 13. Sample ODA Supervision Record … 15
vii
Paragraph Page
Figure 14. Memorandum of Understanding … 17 Figure 15. Sample Conformity Inspection Plan … 20 Figure 16. Sample Inspection Notification Letter … 24 Figure 17. Sample Inspection Discrepancy Record … 25 Figure 18. Sample Inspection Report Cover Sheet … 27 Figure 19. Sample Inspection Survey Sheet … 28 Figure 20. Sample Inspection Report Transmittal Letter … 30 Figure 21. Sample PMA Supplement-Licensing … 31 Figure 22. Sample PMA Supplement-Test and Computations … 32 Figure 23. Sample PMA Supplement-STC … 33 Figure 24. Sample PMA Supplement-All Types … 33 Figure 25. Sample FAA Form 8130-31, Statement of Conformity-Military Aircraft … 34 Figure 26. Sample ODA Termination Letter … 37 Figure 27. Sample ODA Suspension Letter … 39
Appendix B. Sample ODA Procedures Manual (16 pages)
Appendix C. Standardized DOIP Criteria (58 pages)
Appendix D. Certification Plans (TC and STC ODAs) (2 pages)
Appendix E. Related FAA Publications (2 pages)
Appendix F. Definitions (2 pages)
Appendix G. Acronyms (3 pages)
Appendix H. Administrative Information (1 page)
H-1. Distribution … 1 H-2. Authority to Change This Order … 1 H-3. Deviations … 1 H-4. Records Management … 1 H-5. Directive Feedback … 1
Appendix I. FAA Directive Feedback Form (1 page)
5/16/13 8100.15B
Chapter 1. Introduction
1-1. Purpose. This order outlines the Federal Aviation Administration’s (FAA) Organization Designation Authorization (ODA) program. Under this program, the FAA can delegate certain types of authority to organizations. This order addresses how to qualify, appoint, and oversee organizations in the ODA program.
1-4. Explanation of Policy Changes. › h. Provides procedures for removal of ODA unit members with performance…
1-2. Audience. The FAA wrote this order for Aircraft Certification Service (AIR) and Flight Standards Service personnel who manage delegated organizations. The FAA also wrote this order for organizations granted an ODA to act on the FAA’s behalf.
1-3. Where You Can Find This Order. You can find this order on the MyFAA employee website: https://employees.faa.gov/tools_resources/orders_notices, http://www.faa.gov/regulations_policies/orders_notices/ and on the Regulatory and Guidance Library (RGL) website: http://rgl.faa.gov.
1-4. Explanation of Policy Changes. This revision incorporates the following changes:
a. Establishes that the Organization Management Team (OMT) has the discretion to determine that an ODA holder’s procedures are equivalent to referenced FAA procedural requirements. See paragraph 2-7 of this order.
b. Clarifies the ODA unit member selection process and requires the OMT to review all ODA unit member selection decisions for at least two years. See paragraph 3-13 of this order.
c. Requires ODA holders to submit reports on the training status of its manufacturing unit members. See paragraph 3-16e of this order.
d. Requires that ODA procedures manual language addressing certification project notification (CPN) requirements be coordinated with the accountable directorate standards staff. See paragraphs 4-3d(4) and 5-3a(2)(a) of this order.
e. Requires the OMT lead to expedite the review of procedures manual revisions which address policy changes, corrective actions, or findings from self-audits or FAA oversight. See paragraph 5-3a(2)(a) of this order.
f. Clarifies that OMT leads must complete FAA Academy Course 12020, Compliance and Enforcement Procedures. See paragraph 5-2f(3) of this order.
g. Requires that the OMT retain only the last 3 self-audit reports submitted by the ODA holder. See paragraph 5-3d(1)(i) of this order.
h. Provides procedures for removal of ODA unit members with performance problems and requires the OMT to input information into the Designee Information Network (DIN) regarding ODA unit members who have been removed for misconduct, including lack of care or judgment or lack of integrity issues. See paragraphs 5-6d and 16-5 of this order.
1-4. Explanation of Policy Changes. › u. Requires Parts Manufacturer Approval (PMA) ODA holders which are…
5/16/13 8100.15B
i. Requires annual supervision to be based on the fiscal year calendar. See paragraph 5-4a of this order.
j. Addresses appropriate communications and interactions between the OMT and the ODA holder/unit members. See paragraph 5-4i of this order.
k. Eliminates information regarding the correction of non-compliant conditions. See paragraph 5-6b of this order.
l. Allows for use of electronic tools to temporarily capture and maintain inspection discrepancy records. See paragraph 6-5g of this order.
m. Requires Type Certification ODA (TC ODA) and Supplemental Type Certification ODA (STC ODA) holders to submit recommendations for FAA specific findings or FAA participation with their program notification letters. See paragraphs 8-6b and 11-7b. It also requires their OMTs to provide the ODA holder with the rationale for specific findings or FAA participation in ODA projects. See paragraph 8-6c and 11-7e of this order.
n. Requires the geographic MIDO to approve limitations on experimental airworthiness certificates issued by the geographic MIDO the kTC and STC ODA holders. See paragraphs 8-11 and 11-13 of this order.
o. Clarifies that FAA participation in Final Type Certification Board Meetings is only mandatory for new type certificate projects. See paragraph 8-15t of this order.
p. Requires the certificate managing Aircraft Certification Office (ACO), rather than the STC ODA holder, to provide a copy of an STC to AIR-110. Also requires an ODA holder which issues an STC outside of its managing ACO’s geographic area to coordinate with the geographic ACO for the STC holder. See paragraph 11-7l(2) of this order.
q. Clarifies airworthiness function codes. See Chapters 8 through 13 of this order.
r. Requires Major Repair, Major Alteration and Airworthiness ODA (MRA ODA) holders to provide airworthiness certification packages to the OMT’s flight standards representative, rather than the OMT lead. See paragraphs12-7 and 12-8 of this order.
s. Requires MRA ODA holders authorized airworthiness approval functions to hold a part 121, 135, or 145 certificate. See paragraph 12-2c.
t. Eliminates the requirement to submit a copy of the PMA assist letter or reference to the STC number with the program notification for PMA substantiated by STC or licensing. The ODA holder must verify these are available before issuing the PMA supplement. See paragraphs 13-7a and 13-7e of this order.
u. Requires Parts Manufacturer Approval (PMA) ODA holders which are authorized to approve major repair data to include procedures for approval of such data in their ODA procedures manual. See paragraph 13-12j of this order.
1-6. General. › d. The ODA program does not affect how the FAA delegates authority to…
5/16/13 8100.15B
v. Eliminates the requirement to use the certification project notification (CPN) process to coordinate PMA projects for critical or life-limited parts substantiated by STC or licensing. See paragraph 13-7b of this order.
w. Revises inspection criteria to improve assessment of software. See appendix C, section 3 of this order.
x. Updates FAA Forms and record templates. See appendix A, figures 1, 11, 12 and 17 of this order.
1-5. Effective Date. This order is effective June 17, 2013. Those provisions requiring the revision of ODA procedures manuals must be incorporated into approved ODA procedures manuals by January 17, 2014. ODA holders must submit revised procedures manuals for approval by October 18, 2013 or as required earlier by their OMTs.
1-6. General.
a. Under Title 49 of the United States Code (49 USC) 44702(d), the FAA may delegate to a qualified private person a matter related to issuing certificates, or related to the examination, testing, and inspection necessary to issue a certificate on behalf of the FAA Administrator as authorized by statute to issue under 49 USC 44702(a).
b. The FAA established the ODA program in Title 14 of the Code of Federal Regulations (14 CFR) part 183, subpart D, which addresses all FAA delegations to organizations.
c. Because some ODAs involve both AIR and AFS functions, AIR and AFS personnel must work simultaneously or in coordination with each other to oversee these ODAs.
d. The ODA program does not affect how the FAA delegates authority to individuals under 14 CFR part 183, subparts A through C. However, organizations with an ODA must use ODA authority if available, rather than individual designees.
2-4. Types of ODAs. › b. Production Certification oda (PC ODA). Holders of a PC ODA may issue…
5/16/13 8100.15B
Chapter 2. Program Overview
2-1. FAA Appointment of ODAs. The FAA may not grant an ODA to every qualified applicant. The FAA will only grant ODAs when it determines the following:
a. The organization’s FAA workload is large enough to warrant approval;
b. The FAA will benefit from granting the ODA; and
c. The FAA has the resources available to manage the authorization.
2-2. Eligibility For ODA. Any organization consisting of two or more individuals may apply for an ODA. However, every organization is not eligible for every ODA type. For some ODA types, the organization must be a certificate holder or meet specific eligibility requirements. For example, only a PMA holder can get a PMA ODA.
2-3. Definition of ODA Holder and ODA Unit. An ODA holder is the organization to which the FAA grants the ODA. It may be a certificate holder, such as a repair station or aircraft operator, or a consultant group. The ODA unit is the group of individuals (at least two) within the ODA holder that perform the authorized functions. For consultant groups, the ODA holder may consist entirely of the ODA unit. In this order, some requirements apply specifically to the ODA holder, others to the unit. The ODA holder is responsible for administering the ODA unit, and ensuring all requirements of this order are met.
2-4. Types of ODAs. There are eight types of ODA programs. Each type has a chapter in this order that addresses qualifications and functions. To perform functions available to a certain ODA type, organizations must meet certain eligibility requirements. These organizations, when performing delegated functions, must follow all applicable FAA regulations and policies appropriate to those functions. These ODA organizations must use authorized unit members to perform all of the FAA functions necessary for FAA approvals unless specifically provided for otherwise within this order. See figures 2-1, 2-2, and 2-3 of this order for an overview of the available functions. Other types of ODA programs may be added by the appropriate headquarters policy office by future changes to this order.
a. Type Certification ODA (TC ODA). Holders of a TC ODA may manage and make findings for type certification programs. In addition to the engineering and manufacturing approvals that are part of the certification program, a TC ODA holder may issue airworthiness certificates, but may not issue an original type certificate (TC) or amended TC. A TC ODA is available to organizations holding a TC issued by the FAA.
b. Production Certification ODA (PC ODA). Holders of a PC ODA may issue airworthiness certificates and approvals, determine conformity, perform evaluation leading to amendment of its production limitation record, and approve minor changes to its quality control manual. To qualify for a PC ODA, an applicant must be an existing production certificate (PC) holder, or have applied for a TC and PC.
2-4. Types of ODAs. › h. Air Operator ODA (AO ODA). Holders of an AO ODA may conduct…
c. Supplemental Type Certification ODA (STC ODA). Holders of a STC ODA may develop and issue supplemental type certificates (STC)s and related airworthiness certificates. An STC ODA is intended primarily for repair stations, operators, and manufacturers, but consultant groups with the required knowledge and experience may also qualify for an STC ODA.
d. Technical Standard Order Authorization Holder ODA (TSOA ODA). Holders of a TSOA ODA may issue airworthiness approvals and determine conformity of articles, test articles and test set-ups in support of FAA managed TC or STC projects. Only existing technical standard order (TSO) authorization holders qualify for a TSOA ODA.
e. Major Repair, Alteration, and Airworthiness ODA (MRA ODA). Holders of an MRA ODA may approve data for major repairs and alterations, issue airworthiness certificates and approvals, and perform aging aircraft inspections and records reviews. Repair stations and operators qualify for all functions available under MRA ODA. Consultant groups are only eligible for engineering approval functions.
f. Parts Manufacturer Approval ODA (PMA ODA). Holders of a PMA ODA may issue PMA supplements based on test and computation approvals, STCs, or licensing agreements. Only existing PMA holders qualify for this ODA type.
g. Airman Knowledge Testing ODA (AKT ODA). Holders of an AKT ODA type are responsible for testing center personnel and facility management, administration and delivery of airman knowledge tests, and issuance of airman knowledge test reports (AKTR) to airman applicants. The AKT ODA managing office is the Airman Testing Standards Branch (AFS-630), located in Oklahoma City, Oklahoma. AKT ODA must be reviewed, approved, and authorized by this office.
h. Air Operator ODA (AO ODA). Holders of an AO ODA may conduct certification or portions of the certification process towards issuance of a Rotorcraft External-Load Operator Certificate, or approve Aircraft Inspection Programs for eligible part 91 aircraft. ODAs for operational certifications may be expanded in future revisions of this order to include additional air operator, airman, air carrier, or air agency certification functions.
Figure 2-1. ODA Functions
CHAP 8 TC ODA
CHAP 9 PC ODA
CHAP 10
TSOA
ODA
CHAP 11 STC ODA
CHAP 12
MRA ODA
CHAP 13
PMA ODA
CHAP 14
AKT ODA AVAILABLE FUNCTIONS
APPROVE TECHNICAL DATA AND FIND COMPLIANCE TO THE AIRWORTHINESS
STANDARDS
8010 (E) 11010 (E) 13010 (E)
ISSUE STCS and/or AMENDMENTS 11020 (E)
ISSUE and REVISE PMA SUPPLEMENTS
BASED ON TEST AND COMPUTATIONS 13031 (M)
BASED ON LICENSING AGREEMENT OR STC 13032 (M)
APPROVE OPERATIONAL OR REPAIR
INFORMATION 8040 (E) 11040 (E)
12040 (E)
13040 (E)
APPROVE AIRWORTHINESS LIMITATIONS
INFORMATION 8050 (E) 11050 (E)
12050 (E)
13050 (E)
ISSUE AIRWORTHINESS CERTIFICATES &
APPROVALS See figure 2-2 for Airworthiness Functions
ESTABLISH CONFORMITY INSPECTION
REQUIREMENTS 8070 (E) 9070 (M) 11070 (E)
13070 (E, M)
DETERMINE CONFORMITY OF ARTICLES
INCLUDING TEST ARTICLES 8080 (M) 9080 (M)
10080 (M)
11080 (M)
13080 (M)
DETERMINE CONFORMITY OF TEST SETUP 8090 (M) 9090 (M)
10090 (M)
11090 (M)
13090 (M)
DETERMINE CONFORMITY OF INSTALLATIONS
OF ARTICLES, INCLUDING TIA INSPECTIONS
ON A PRODUCT
8100 (M) 9100 (M)
11100 M 13100 (M)
PERFORM COMPLIANCE INSPECTIONS 8110 (E) 11110 E 13110 (E)
EVALUATE PRODUCTION LIMITATIONS RECORD , PC AND PROCESS CHANGES 9120 (M)
APPROVE DATA FOR MAJOR ALTERATIONS
OR MAJOR REPAIRS 8130 (E)
11130 E 12130 (E)
13130 (E)
PERFORM AGING AIRCRAFT INSPECTIONS
AND RECORDS REVIEWS
12140 O
APPROVE MINOR CHANGES TO QUALITY
CONTROL MANUAL/PROCEDURES
9150 (M)
PERFORM APPROVALS IN SUPPORT OF TC
ODA HOLDER PROJECTS 8160 11160 13160
ISSUE FAA FORM 8130-31, STATEMENT OF
CONFORMITY - MILITARY AIRCRAFT 8170 (M) 9170 (M)
11170 (M)
PERFORM REVIEW AND ACCEPTANCE OF
INSTRUCTIONS FOR CONTINUED
AIRWORTHINESS (ICA)
8180 (A)
11180 (A)
13180 (A)
Legend: Primary FAA Office: A=Aircraft Evaluation Division; E=Aircraft Certification Office; M=Manufacturing Inspection District Office; and O=Flight Standards Office
Note: For function code descriptions and additional clarification, see specific chapters of this order. Underlined codes are available to consultant group organizations.
Figure 2-2. Airworthiness Certificate and Approval Functions
CHAP 8 TC ODA
CHAP 9 PC ODA
CHAP 10 TSO ODA
CHAP 11 STC ODA
CHAP 12 MRA ODA
CHAP 13 PMA ODA
CHAP 14 AKT ODA AVAILABLE FUNCTION CODES
ISSUE/AMEND STANDARD AIRWORTHINESS CERTIFICATES 8061 (M) 9061 (M) 11061 (M)
12061 (O)
ISSUE/AMEND SPECIAL AIRWORTHINESS CERTIFICATES 8062 (M) 9062 (M) 11062 (M)
12062 (O)
ISSUE DOMESTIC AIRWORTHINESS APPROVALS 9063 (M) 10063 (M) 12063 (O)
13063 (M)
ISSUE EXPORT AIRWORTHINESS
APPROVALS 9064 (M) 10064 (M) 12064 (O)
13064 (M)
ISSUE EXPORT AIRWORTHINESS
APPROVALS 9065 (M) 12065 (O)
ISSUE SPECIAL FLIGHT PERMITS 8066 (M) 9066 (M) 11066 (M)
12066 (O)
ISSUE/AMEND SPECIAL AIRWORTHINESS CERTIFICATES
FOR PRIMARY CATEGORY
AIRCRAFT
9067 (M) 11067 (M)
ISSUE/AMEND SPECIAL AIRWORTHINESS CERTIFICATES
FOR RESTRICTED CATEGORY
AIRCRAFT
9068 (M) 11068 (M)
12068 (O)
ISSUE PROVISIONAL AIRWORTHINESS CERTIFICATES 9069 (M)
ISSUE A REPLACEMENT AIRWORTHINESS CERTIFICATE 110610 (M)
120610 (O)
DELIVERY OF AIRMAN
KNOWLEDGE TESTS 1401(S)
Legend: Primary FAA Office: M=MIDO; O=FSO; and S=AFS-630
Note: For function code descriptions and additional clarification, see specific chapters of this order. Underlined codes are available to consultant group organizations.
Chapter 2. Program Overview › 2-7. Applicability of Referenced FAA Procedures.
Figure 2-3. Operational Approval Functions
CHAPTER 15
AO ODA Part 133
CHAPTER 15
AO ODA
Part 91 AVAILABLE FUNCTION CODES
REVIEW ELIGIBILITY 15010 (O)
EVALUATE RLCFM 15020 (O)
ADMINISTER CHIEF PILOT TESTS 15030 (O)
ADMINISTER FLIGHT CHECKS 15040 (O)
VERIFY AIRWORTHINESS 15050 (O)
CONDUCT BASE INSPECTION 15060 (O)
ISSUE OPERATING CERTIFICATE 15070 (O)
EVALUATE AND APPROVE AIRCRAFT INSPECTION
PROGRAM
15080 (O)
DETERMINE ELIGIBILITY OF PREVIOUSLY APPROVED INTERVALS GREATER THAN THE
MANUFACTURER’S INSPECTION INTERVALS
15090 (O)
Legend: Primary FAA Office: A=Aircraft Evaluation Division; E=Aircraft Certification Office; M=Manufacturing Inspection District Office; and O=Flight Standards Office
2-5. Multiple ODA Types. An organization that seeks an ODA may apply for as many types of ODA for which it qualifies. The appointing office will only issue one ODA letter of designation, and assign one ODA number. Organizations with multiple ODA types will usually be required to address all ODA types within a single procedures manual. An organization may have separate procedures manuals for each type of ODA, only if required by the FAA.
2-6. Organization Management Team. The organization management team (OMT) is the group of FAA personnel responsible for oversight of the ODA holder. See paragraph 5-2 of this order for information about OMTs.
2-7. Applicability of Referenced FAA Procedures. This order commonly requires ODA holders to perform FAA functions in accordance with the procedural requirements of other FAA Orders, such as 8110.4, Type Certification, or 8120.22, Production Approval Procedures. In many circumstances, literal compliance with procedural requirements prescribed in other FAA orders may not be possible for an ODA holder because these FAA orders are based on FAA organizational structures and interfaces. In these cases, the reference means to impose a requirement that the ODA holder’s procedures follow the same procedures to the extent possible, given the ODA holder’s structure. If literal compliance is not possible with the referenced order, discretion is given to the OMT to evaluate the ODA holder’s procedures and determine equivalence to the FAA process. It is expected that the ODA holder’s procedures will reflect the
Chapter 2. Program Overview › 2-8. Certification Activity.
defined FAA processes to the extent possible with minimal adaptations needed for implementation in an ODA environment. For Air Operator ODA holders; FAA advisory circulars (AC), FAA notices, and FAA Flight Standards Information Management System (FSIMS), Order 8900.1 and the contents of this order may be used as a guide to complete the functions. The procedures developed and used to comply with these documents will be required to be approved by the OMT, and any revisions thereafter will require submission to and approval by the OMT. Performance of functions, qualifications and training of Unit Members, and other references not specifically addressed by FAA Order 8100.8 will be included in this order.
2-8. Certification Activity. Organizations that are not eligible for or do not want an ODA may continue to use standard certification procedures, including individual designees. Organizations with ODAs are expected to complete all projects possible using ODA authority, but may continue using standard certification procedures for projects or functions not authorized under the ODA. All approval functions needed for project work must be accomplished by the organization’s ODA unit members unless the use of other approvals is provided for in this order.
b. Organizational Model. One key to the success of the ODA system is… › (2) Each ODA unit member must be in a position that provides enough…
5/16/13 8100.15B
Chapter 3. Qualifications, Responsibilities, and Authority
3-1. Granting an ODA. This chapter outlines the general ODA eligibility and qualification requirements. It also explains the general requirements and limitations that apply to all ODAs. The specific requirements for the various types of ODAs are addressed in Chapters 8 through 15 of this order.
3-2. Reducing Designees. The designee system leverages the FAA’s resources by authorizing individuals and organizations to perform functions for the agency. Managing organizations is more efficient for the FAA than managing the activity of many individual designees. The FAA expects an ODA applicant that employs individual designees to significantly reduce the number of designees for the type of ODA functions it seeks. An ODA holder may retain individual designees to operate under standard procedures, if the needed functions are not available under the ODA program.
3-3. ODA Holder Location. Each ODA holder must be located in the United States. However, ODA unit members may be located apart from the ODA holder’s facility if agreed to by the OMT. An ODA holder may appoint ODA unit members in another country only after the OMT decides the ODA unit member’s location poses no undue burden on the FAA. The ODA unit member must attend all required training, and meet with the OMT yearly if required by the OMT. An AO ODA holder may not be appointed nor perform functions outside the United States.
3-4. ODA Holder Qualifications. Every applicant must meet the qualifications in this paragraph as well as the eligibility requirements in Chapters 8 through 15 of this order for the specific type of ODA requested.
a. Integrity. The applicant’s management, its ODA administrator, and the proposed ODA unit members must possess demonstrated integrity in their experience with the FAA.
b. Organizational Model. One key to the success of the ODA system is that the ODA holder’s executive management fully supports the ODA unit. The ODA unit also must be free to do its duties. The organizational model for ODAs will vary significantly depending on the ODA holder’s functions, size, and corporate structure. The model must meet the following:
(1) The ODA administrator must ensure that the organization performs all authorized functions in accordance with the regulations and applicable FAA policy. (Terms used in this order, such as “ODA administrator,” are defined in appendix E of this order.) The ODA administrator must also ensure that the organization always complies with its ODA procedures manual. The ODA administrator must be in a position that provides authority to act in the FAA’s interest.
(2) Each ODA unit member must be in a position that provides enough authority and time to perform duties without pressure or influence from other parts of the organization.
a. ODA Administrator. The ODA administrator must have technical… › (3) Demonstrated sound judgment and integrity.
(3) An ODA unit member must have no conflicting restraints while performing authorized functions. Additionally, an ODA unit member must not have responsibilities that conflict with those of the ODA unit.
c. Experience. Each applicant must have experience and a thorough working knowledge of the FAA regulations, methods of compliance, policy, processes, and procedures applicable to the authorized functions sought. Additionally, applicants seeking a TC, STC, or PMA ODA must have a recent and successful history performing certification work and have completed projects as an organization. For these ODA types, newly formed organizations must complete projects under standard procedures in order to be eligible for ODA even if the ODA members are experienced individuals. An applicant for type and production certificates may be appointed as a PC ODA if it is expected to obtain a production certificate. Each applicant for AO ODA functions must have the ability to manage operator certification projects or program approvals.
d. Resources. Each applicant must have sufficient administrative and technical resources to satisfy all the requirements of the requested authorization. It must employ an ODA administrator and have available an ODA unit consisting of the appropriate personnel capable of performing the authorized functions. Except for the lead administrator, an ODA unit may consist solely of individuals who are not employed full time by the organization.
e. Facilities. Each ODA holder’s primary facilities must be in the United States. The facilities must be appropriate for the ODA sought, as detailed in Chapters 8 through 15 of this order.
3-5. ODA Staff Qualifications. Qualifications for the ODA administrator and ODA unit are as follows:
a. ODA Administrator. The ODA administrator must have technical experience with the functions performed under the ODA and a broad range of management experience. This experience must enable the ODA administrator to manage the entire ODA unit activities effectively. The following are the minimum requirements for an ODA administrator:
(1) At least five years of working experience with the FAA on projects similar to those authorized under the ODA. This experience must include various levels of technical airworthiness responsibilities and experience (for example, compliance engineer, quality assurance inspector, manufacturing inspector, or airworthiness inspector) or technical operations responsibilities and experience (for example, director of operations, chief pilot, safety manager, or operations inspector). The ODA administrator must also have management experience in one or more technical disciplines such as engineering, manufacturing, airworthiness, maintenance, quality assurance, or operations.
(2) Comprehensive knowledge of FAA regulations, policies, and procedures applicable to the ODA functions.
(3) Demonstrated sound judgment and integrity.
b. Engineering and Flight Test ODA Unit Members. › (2) Qualification Requirements for an ODA Unit Member Making Findings…
5/16/13 8100.15B
(4) Sufficient technical knowledge, training, skill, and experience for the type of ODA sought. An ODA administrator need not be qualified to perform all authorized functions but must possess at least a basic understanding of all of the functions performed.
(5) The lead ODA administrator must be a full-time employee of the ODA holder. Alternate ODA administrators need not be full-time employees, but must meet all ODA administrator qualification requirements.
(6) In addition, AKT ODA administrators must:
(a) Have a good reputation and record in the industry and community for integrity and dependability.
(b) Have a willingness to serve the aviation community.
(c) Have a history of cooperation with the FAA (if applicable).
(d) Be at least 21 years of age.
(e) Be citizens or legal resident aliens of the United States (except for locations outside the United States).
(f) Know and understand AKT authorization requirements.
(g) Know computer uses as they relate to the AKT Program.
(h) Be knowledgeable in the structure, processing, and transmission of applicant data.
(i) Know and understand the English language.
b. Engineering and Flight Test ODA Unit Members.
(1) An engineering or flight test ODA unit member must meet the qualifications for a DER. The FAA defines these qualifications in FAA Order 8100.8, Designee Management Handbook. The ODA unit members need to meet only those requirements for the functions and areas they will perform. However, the requirement to have direct working experience with the FAA may be satisfied by having direct working experience within an ODA holder’s or other delegated organization.
(2) Qualification Requirements for an ODA Unit Member Making Findings to Foreign Requirements. The OMT may authorize an ODA holder to make findings of compliance with foreign regulations in support of TC or STC validation programs. Each ODA unit member authorized to make such findings must thoroughly understand the foreign requirements and be knowledgeable of their application. This knowledge typically will be evidenced by participation on previous validation programs with the foreign authority and the FAA. The ODA unit member listing must identify, for each ODA unit member, the foreign requirements to which the ODA unit member is authorized to make findings.
d. AKT Unit Members. Each AKT unit member must: › (8) Know computer uses as they relate to the AKT program.
5/16/13 8100.15B
c. Manufacturing and Maintenance ODA Unit Members.
(1) Each ODA unit member performing airworthiness, conformity, production or maintenance inspections must meet the qualifications to perform those inspections in FAA Order 8100.8. However, the requirement to have direct working experience with the FAA may be satisfied by having direct working experience within an ODA holder’s or other delegated organization.
(2) Each ODA unit member determining conformity of installations must have five years of experience performing conformity inspections of installations on a product.
(3) Each ODA unit member performing type inspection authorization (TIA) inspections must have five years of experience inspecting aircraft systems installations and be able to determine airworthiness of the aircraft before flight testing.
(4) Each ODA unit member performing TIA inspections involving weight and balance of aircraft must have knowledge of weight and balance practices described in FAA Advisory Circular (AC) 120-27, Aircraft Weight and Balance Control.
(5) Each ODA unit member determining conformity of compliance test setups must have two years of experience performing conformity inspections of compliance test setups.
d. AKT Unit Members. Each AKT unit member must:
(1) Have a good reputation and record in the industry and community for integrity and dependability.
(2) Have a willingness to serve the aviation community.
(3) Have a history of cooperation with the FAA.
(4) Be at least 21 years of age.
(5) Be a citizen or legal resident alien of the United States (except for locations outside the United States).
Note: A foreign national may be appointed as an ODA unit member at a location outside the United States. A foreign national may NOT be appointed as an ODA unit member at a location in the United States.
(6) Know policies and requirements outlined in this order.
(7) Know airman knowledge test authorization requirements.
(8) Know computer uses as they relate to the AKT program.
e. Air Operator ODA Unit Members. For Air Operator ODA holders, the… › (6) Each unit member for codes 15080 and 15090 must have specialized…
Note: Former FAA employees must undergo and/or comply with the same approval, background check, training, and oversight processes as any other ODA unit members.
e. Air Operator ODA Unit Members. For Air Operator ODA holders, the baseline experience requirement minimums for unit members are the same as those for a qualified aviation safety inspector (ASI) with the disciplines associated with the functions or the equivalent level of experience and/or authority in aircraft maintenance and inspection activity and completion of all FAA required training prior to performing the functions. For maintenance functions, extensive experience with the same category and class of aircraft is required (as a certificate holder under parts 121/133/135/145) with the appropriate ratings or operating the same make and models. For operations functions, extensive experience as a part 119 management person with the appropriate type ratings and operational experience in the functions and specific make and models.
(1) An AO ODA must consist of unit members who have experience in all aspects of the applicable operational certification functions. Each AO ODA unit member must have at least two years of experience developing AIPs.
(2) Each AO ODA unit member administering pilot knowledge and skill testing, observing operational flight checks, approving operating manuals and training programs, or conducting base inspections must hold the appropriate certificates and ratings similar to those required for an FAA ASI (operations) conducting the same functions. The unit member must also have three years of experience as a pilot in the same type of operation or as an FAA inspector (operations).
(3) Each AO ODA unit member conducting airworthiness record reviews or inspections must meet the qualifications of a DAR-T in FAA Order 8000.95 to perform the specific functions listed based on the category of aircraft (i.e., standard or special airworthiness certification of aircraft or aging aircraft inspections).
(4) Each ODA unit member for function codes 15080 and 15090 must have a mechanics certificate under part 65 and at least 60 months in maintenance or aircraft inspection as an aircraft inspector/mechanic (Inspection Authorization not required), quality control inspector, or supervisory/management over these positions with the experience in the same category and class of aircraft the programs are intended for. See Chapter 15 for more details.
(5) Each ODA unit member for function codes 15080 and 15090 must have experience in maintaining aircraft in the classification and category of operation or specific knowledge of the modifications and alterations performed for the restricted/experimental operation prior to being assigned an ODA project performing function codes 15080 or 15090. For example, projects involving experimental aircraft for (showing compliance, Research & Development), restricted category for operations in (rotorcraft external load, space vehicle launch, or target towing), limited category large and turbine-powered aircraft.
(6) Each unit member for codes 15080 and 15090 must have specialized knowledge/experience in aircraft maintenance, inspection programs, and technical publications
commensurate with aircraft program development. This experience must have been gained in activities that resulted in the approval of aircraft inspection or maintenance programs with the FAA.
3-7. Memorandum of Understanding. › a. ODA Holder’s Commitment. An ODA holder agrees to use the same care,…
3-6. Responsibilities. ODA holders and units must follow the FAA regulations, directives, policies, guidance, and procedures as applicable to the authorized functions. The responsibility for finding compliance with the regulations and applicable policy remains with the ODA holder. The ODA holder is responsible for the activity of the ODA unit and ODA administrator.
a. ODA Holder. The ODA holder must ensure that its ODA administrators and ODA units remain free to perform their authorized functions in accordance with FAA regulations, and are not subject to conflicts of interest that might impact their ODA unit responsibilities. In addition to performing their authorized functions, the ODA unit members must have enough time and resources to keep up to date on the current FAA regulations, directives, and guidance applicable to the authorized functions.
b. ODA Administrator. The ODA administrator manages the ODA unit activities and communicates with the OMT. The ODA administrator must ensure that the ODA unit has sufficient organizational authority and resources to perform its authorized functions in accordance with FAA requirements. The ODA administrator must report to a level of management that is senior enough to enable the ODA unit to administer duties for the FAA, without undue pressure or influence from other organizational segments or individuals. The ODA administrator must ensure that the organization follows the procedures in its procedures manual and that the processes comply with all applicable FAA regulations and policy. If the ODA holder has more than one ODA administrator, a lead ODA administrator must be identified.
c. ODA Unit. Each ODA unit member must:
(1) Comply with the procedures in the approved procedures manual.
(2) Meet the qualifications for specific functions under the ODA.
(3) Cooperate with the FAA when the FAA oversees the ODA holder.
d. Separation of Duties. ODA holders and unit members should be aware that the delegated functions performed as an individual designee are separate and distinct from the functions performed as an ODA unit member.
3-7. Memorandum of Understanding.
a. ODA Holder’s Commitment. An ODA holder agrees to use the same care, diligence, judgment, and responsibility when performing the authorized functions as the FAA would use in performing the function. This commitment starts at the senior management level of the ODA holder and extends through the ODA administrator, ODA unit, and the rest of the applicant’s organization. As proof of that commitment, senior management of the organization will sign a memorandum of understanding (MOU) that outlines the charter, authority, and responsibility of
a. Content. The procedures manual must address all procedures and… › (3) Procedure for revising the procedures manual and obtaining approval…
the ODA holder. As a minimum, the MOU must contain the language in appendix A, figure 14 of this order.
b. Preparing an MOU. The prospective OMT and ODA holder jointly prepare the MOU. The ODA holder’s senior management must sign the MOU before the ODA is issued. Appendix A, figure 14 of this order contains acceptable MOU. All personnel within the ODA holder that manage ODA unit members in any capacity must read and understand the MOU.
c. Changes to ODA Holder Signatories. Any time an ODA holder signatory of the MOU changes, the replacement must sign a revised MOU. If an ODA holder’s new senior management refuses to sign the MOU, the managing office must terminate the ODA. The revised MOU must be provided to the OMT lead within 90 days.
3-8. Authority and Functions.
a. Functions Available. The functions that may be authorized are shown in figures 2-1, 2-2 and 2-3 of this order. Each chapter in this order that covers an ODA type gives specific function code descriptions. Limitations for each ODA type are given in Chapters 8 through 15 of this order as well. Individual limitations will be identified in the approved procedures manual.
b. Authorized Functions. We will identify the authorized ODA types in the letter of designation and specify the authorized functions and limitations in the ODA procedures manual. See appendix A, figure 3 of this order for an example of an ODA letter of designation. To add functions, an ODA holder must apply in accordance with 14 CFR 183.43 and paragraph 4-2 of this order. The FAA must approve any changes in functions before they may be performed.
c. Products and/or Articles Selected. The ODA is limited to the products and/or articles identified in the procedures manual and approved by the OMT.
3-9. Procedures Manual. Each ODA holder must perform all authorized functions in accordance with its FAA-approved procedures manual. The procedures manual must be available to all members of the ODA unit.
a. Content. The procedures manual must address all procedures and limitations regarding functions performed by the ODA holder. The OMT may not use separate documentation to establish agreements or procedures for functions performed by the ODA holder. The procedures manual must contain at least the following (See appendix B of this order for format and Chapters 8 through 15 for detailed requirements.):
(1) Signature blocks for the FAA managing office(s) and ODA administrators. A single aircraft evaluation group (AEG) managing office manager may sign the procedures manual on behalf of any other AEG managing office(s) manager.
(2) General table of contents and a method for maintaining configuration control such as complete revision control or a log of revisions/list of effective pages.
(3) Procedure for revising the procedures manual and obtaining approval of revisions.
a. Content. The procedures manual must address all procedures and… › (19) Corrective action procedures.
5/16/13 8100.15B
(a) Definition of manual changes which don’t require OMT approval. See appendix B, section III for more information.
(b) Method of documenting OMT approval of changes.
(c) Method of documenting and determining approval requirements for changes in facilities or organizational structure.
(4) Preface and introduction, including procedures for FAA and ODA holder communications. The ODA holder’s procedures for communications must address the types of communications that are appropriate between the ODA holder/unit and the OMT. The types of communications may vary based on the size and complexity of the organization and the working arrangements with its OMT.
(5) Authorized functions and limitations. Limitations section must identify the products and/or articles addressed by the ODA holder’s authority.
(6) Description of the ODA holder and ODA unit organizational structure and responsibilities.
(7) ODA administrator and unit member duties and responsibilities.
(8) Required capabilities and ODA unit positions.
(9) Unit member listing information (see paragraph 3-13g of this order).
(10) Procedures to select and remove ODA unit members and coordinate ODA unit member selections with the FAA, when required.
(11) Description of the training courses each ODA unit member and ODA administrator must complete. Include standardization, recurrent, and in-house training.
(12) Self-audit procedures and responsibilities.
(13) Duration of the ODA.
(14) Maintenance of eligibility.
(15) Acknowledgement of the FAA’s right to inspect the ODA holder or unit.
(16) Procedures for performing continued airworthiness functions, including investigation and resolution of service difficulties and potentially unsafe, or non-compliant conditions.
(17) Procedures for performing authorized functions.
(18) Records maintenance and submittal requirements.
(19) Corrective action procedures.
a. ODA Holder-Provided Training. An ODA holder must provide training to… › (4) Applicable FAA regulations, policy, and guidance material.
(20) Procedures for obtaining and maintaining related regulatory and guidance material.
(21) Procedures to report manufacturing activity, if applicable.
(22) Procedures for determining the impact of operational suitability issue and coordinating with the AEG.
(23) Procedures to report air operator certification activity, if applicable.
(24) Appendices:
(a) MOU.
(b) Organization charts of ODA holder and unit and company interface.
(c) Facility descriptions and addresses of ODA unit members, including remote locations.
(d) ODA unit position descriptions and required qualifications.
(e) Sample forms used within the ODA system.
(f) Content of certification plans.
b. Approval. The OMT must review and approve those changes that require approval before the ODA unit performs any function affected by the change. Approval by the OMT will be indicated by FAA signature on the log of revisions page or other means agreed to by the OMT. The ODA holder must submit to the OMT any change to its manual which is incorporated without OMT approval within 30 calendar days after the manual is revised.
3-10. Training.
a. ODA Holder-Provided Training. An ODA holder must provide training to its ODA administrator and unit members to ensure continued compliance with the approved procedures manual, the regulations, and applicable FAA policies. An ODA holder must provide this training before authorizing an ODA unit member to perform a delegated function. ODA unit members must receive this training at least every two years. An ODA holder must allow the FAA to review the training materials and attend any training session. An ODA holder must incorporate changes to the training material as required by the FAA. The training must explain:
(1) The ODA holder’s processes, and its procedures manual, including documentation and forms.
(2) The functions delegated to the authorization.
(3) The ODA unit member’s authority and responsibility when performing authorized functions.
(4) Applicable FAA regulations, policy, and guidance material.
3-11. Duration of Appointments. › c. Change to the ODA Unit. A change in the ODA unit that involves ODA…
b. Temporary ODA unit members or those unit members with limited use are only required to receive that ODA holder training commensurate with their involvement in the project. For example, an engineering ODA unit member performing a burn test or manufacturing ODA unit member performing specific article conformity inspections at a supplier location would not need training on all of the organization’s functions and procedures. The ODA holder must provide the ODA unit member sufficient training on the specific procedures related to the ODA unit member’s functions. The scope, usage and content of such limited training must be agreed to by the OMT.
c. FAA Seminars. Each ODA unit member, in addition to the ODA holder’s training, must attend the following FAA-sponsored training:
(1) Except for AKT ODA administrators, each ODA lead administrator and those administrators overseeing a “type” of ODA authority (TC, STC, PC, etc.) must complete ODA applicant training prior to appointment. This training is available on-line at https://avinfo.faa.gov/DsgReg/Sections.aspx and includes a “Part I” and “Part II” module based on the type of authority sought. These administrators must also attend an ODA seminar at least every two calendar years. The AKT ODA OMT lead may administer program-specific training to AKT ODA lead administrators every calendar year at an annual meeting as a substitute for attending the ODA seminar.
(2) Each ODA unit member performing certain functions must attend FAA training seminars as described at http://www.faa.gov/other_visit/aviation_industry/designees_delegations/training/ or equivalent training that is determined acceptable by AIR-160 or AFS-600. If an ODA holder desires to rely on equivalent training it must inform the OMT. If the OMT determines that the ODA holder is capable of conducting equivalent training, the OMT will coordinate with AIR-160 or AFS-600 regarding training materials and delivery requirements.
d. Standardization Workshops. If required by the OMT, ODA unit members must attend FAA standardization workshops. Standardization workshops are subject-specific and usually developed and presented by FAA personnel or industry personnel as needed.
3-11. Duration of Appointments. An ODA is effective until the expiration date listed on the letter of designation. See paragraphs 4-4 and 5-8 of this order for guidance on the allowed duration of an appointment.
a. Transferability. An ODA is not transferable.
b. Change in Ownership. A change in ownership of the ODA holder as a result of a company name change or a corporate merger, no change in organizational structure, etc., may be executed by reissuing the ODA letter of designation and the MOU, along with revising the procedures manual to reflect the new name.
c. Change to the ODA Unit. A change in the ODA unit that involves ODA administrators, structure within the ODA holder, or changes to the ODA holder or ODA unit, may change an organization’s eligibility for ODA. The ODA holder must notify its OMT lead of anticipated
3-13. Selection of ODA Unit Members. › a. FAA Pre-screening of Proposed Unit Members. The ODA unit member…
organizational changes to determine whether the changes will impact the authorization and how they will be handled.
3-12. Continued Eligibility. To maintain eligibility, an ODA holder must:
a. Notify the OMT lead within 48 hours of any change that would affect the ODA holder’s ability to meet the requirements of its authorization. A notification due on Saturday, Sunday, or a holiday may be delivered on the next working day.
b. Comply with the requirements in its approved procedures manual.
c. Maintain a staff of qualified ODA unit members.
d. Implement corrective action for deficiencies identified by the FAA.
e. Not perform an authorized function if a change in the facilities, resources, or organizational structure affects how the ODA holder performs that function. This includes a move to a new location or the inability of the ODA holder to accommodate the ODA unit or records needed to perform the authorized function. The ODA holder may perform that function only after it notifies the OMT lead of the change, and the OMT documents and approves the change as required in the ODA holder’s procedures manual.
f. Not perform any authorized function if it moves its principal manufacturing facility or adds another facility, if an ODA holder’s basis of eligibility is a PC. The ODA holder must notify the OMT of the change in accordance with 14 CFR 21.150, or any other issue that may affect the quality system. In this case, the company would have to apply for a PC extension or a new PC in accordance with 14 CFR 21.133.
Note: A PC is not transferable, see 14 CFR 21.144.
g. Not perform any authorized function if it moves its principal manufacturing facility or adds another facility, if an ODA holder’s basis of eligibility is a PMA. The ODA holder must notify the OMT of the change in accordance with 14 CFR 21.309. In this case, the company would have to apply for a new PMA or an extension to its production approval.
h. If an ODA holder’s basis of eligibility is a TSOA, the ODA holder cannot perform any authorized function if it moves its principal manufacturing facility or adds another facility. The ODA holder must notify the OMT of the change since a TSOA is not transferable in accordance with 14 CFR 21.614. In this case, the company would have to apply for TSOA in accordance with 14 CFR 21.603.
3-13. Selection of ODA Unit Members. The ODA holder must select qualified ODA unit members. The ODA holder’s procedures manual must contain its ODA unit member selection and approval process and documentation. See figure 3-1. This section does not apply to the selection of administrators.
a. FAA Pre-screening of Proposed Unit Members. The ODA unit member selection process for any proposed unit member (including existing designees or unit members at other
ODA holders) must include an initial notification to the OMT identifying the individual. The ODA holder is advised to coordinate with the OMT before it expends significant resources evaluating the individual. The OMT must investigate the individual and inform the ODA holder if the FAA is aware of any information that indicates that the individual has demonstrated a lack of care or judgment, or a lack of integrity, or is otherwise unsuitable to act as an ODA unit member. This investigation must include at least review of both the active and archival DIN and Designee Management System (DMS) databases. The AFS OMT members must review Program Tracking & Reporting Subsystem records for historical information. In addition to pre-screening, in some cases the OMT may also review ODA unit member selection decisions before the ODA holder may add a new ODA unit member to the staff. See paragraph 3-13d of this order. FAA pre-screening is not required for proposed AKT ODA unit members unless directed by the OMT or the AKT ODA managing office.
5/16/13 8100.15B
Figure 3-1. ODA Unit Member Selection Process
b. Existing Designees or ODA Unit Members at Another Delegated Organization. An ODA holder can appoint prospective ODA unit members that are existing designees without evaluating their qualifications if they will perform the same functions within its ODA unit. The ODA holder must maintain evidence of the ODA unit member’s designee authority. An ODA unit member from another delegated organization may be similarly appointed if the other delegated organization provides evidence of the ODA unit member’s authority and limitations. The ODA unit member must have experience on the same type and complexity of projects performed by the ODA holder. If the prospective ODA unit member is expected to perform any functions outside the scope of current authority, the ODA holder must evaluate the unit member for additional functions according to paragraph 3-13c of this order.
3-13. Selection of ODA Unit Members. › f. Appointment of ODA Unit Members at Foreign Locations. If the ODA…
c. Other Individuals. The ODA holder must evaluate each prospective ODA unit member who is not currently a designee or ODA unit member using a process and preparing documentation similar to that used by the FAA to evaluate designee applicants. For more information, see FAA Order 8100.8, 8000.95, or the specific requirements identified in Chapter 15 of this order.
d. FAA Review of ODA Unit Member Selection Decisions. It is the FAA’s intention for ODA holders ultimately to select ODA unit members without OMT concurrence on selection decisions. However, the OMT must review ODA unit selection decisions for at least two years after ODA appointment and as long as necessary for the ODA holder to prove that it can select ODA unit members that meet the qualification requirements.
(1) During the initial evaluation of ODA applicants, all proposed ODA unit member appointment packages should be reviewed by the OMT prior to appointing the ODA holder.
(2) For a period of two years after the initial ODA appointment, selection decisions for proposed ODA unit members, who are not currently designees or ODA unit members at other delegated organizations, must be reviewed by the OMT prior to the ODA unit member performing any authorized function for the ODA unit.
(3) After two years, the FAA anticipates that the OMT will not need to review any ODA unit member selection decisions unless the ODA holder has not had sufficient activity appointing ODA unit members or there are documented problems with the ODA holder’s selection process or performance. The OMT must document these problems and actively pursue corrective action with the ODA holder to improve the ODA holder’s selection process or performance.
e. Coordination of Proposed Noise Unit Members with AEE-100. The selection of unit members with authority to make approvals for 14 CFR part 36 must be coordinated with the Office of Environment and Energy, Noise Division (AEE-100). This coordination may be done by either the OMT or by the ODA holder as part of its selection process. Procedures for coordination with AEE-100 must be addressed in the ODA holder’s procedures manual if authorized to make 14 CFR part 36 approvals.
f. Appointment of ODA Unit Members at Foreign Locations. If the ODA holder desires to appoint an ODA unit member at a foreign location, it must get OMT concurrence on the
3-14. Self-Audit. › a. Personnel. The self-audit must include evaluation of each ODA unit…
location and functions to be performed by the ODA unit member. The ODA unit member is subject to the same training and oversight requirements as domestic ODA unit members.
g. ODA Unit Member Listing. The ODA holder must maintain a listing of active ODA unit members. The listing may be in any format acceptable to the OMT and must be provided to the OMT as required. The OMT must be notified and provided contact information for the individual if the removal of a unit member from the active listing was based on ODA-related performance. (See paragraph 5-6d(5) of this order.)
(1) For each unit member, the listing must contain:
(a) Name,
(b) Signatures,
(c) Functions and limitations for each unit member,
(d) Location and name of the company for any unit member located at facilities not identified in appendix C of the ODA procedures manual,
(e) Authority and limitations corresponding to the organization’s authority and functions defined in appendix D of the ODA procedures manual. The authority for all members will be defined by function codes from this order, and engineering unit member authority further described by discipline, and authorized areas/delegated functions using the charts of FAA Order 8110.37.
(f) For AO ODA unit members, the type, number, and ratings for each airmen certificate required for the function (if applicable).
(2) The procedures manual must describe:
(a) How the unit member listing will be updated and maintained,
(b) The format of the listing, and
(c) The procedures for coordinating changes to the listing with the OMT along with the information the organization will provide to the OMT while unit member selection decisions are under review by the FAA.
3-14. Self-Audit. The ODA holder must perform self-audits that evaluate the ODA unit members, the ODA processes, and compliance with all applicable FAA regulations and policy. A self-audit must be performed at least once every 12 months, and as requested by the OMT. The self-audit does not replace the FAA inspection required by this order. The procedures manual must contain the ODA holder’s audit procedures.
a. Personnel. The self-audit must include evaluation of each ODA unit member using the processes and criteria contained in FAA Order 8100.8, 8000.95, or FAA Order 8900.1, Flight Standards Information Management System (FSIMS), as appropriate for the functions performed
Chapter 3. Qualifications, Responsibilities, and Authority › 3-17. Records.
by the ODA unit member. The evaluation must include review of individual ODA unit members’ work for accuracy. This includes ODA unit members located at suppliers or at other locations away from the ODA holder’s facility. The ODA holder must make at least one on-site visit every 18 months to manage an ODA inspection unit member’s activity.
b. Procedures. The self-audit must include evaluation of the procedures used to perform all authorized functions and the other requirements of the authorization, including ODA unit appointment and training, and service difficulty support.
c. Compliance with Procedures. The self-audit must evaluate whether the ODA holder complies with its procedures manual.
d. Self-Audit Records. The ODA holder must maintain records of its self-audits and submit copies to the OMT within 14 calendar days of completion.
e. Corrective Action. The ODA unit will review proposed corrective actions before submittal to the FAA.
3-15. Self-Disclosure. Pursuant to FAA Order 2150.3, FAA Compliance and Enforcement Program, the FAA may elect not to seek a civil penalty for 14 CFR part 183 regulatory violations if the ODA holder notifies us of the noncompliance in accordance with the criteria of AC 00-58, Voluntary Disclosure Reporting Program. See FAA Order 2150.3 and AC 00-58, for more information.
3-16. Work Activity Reports.
a. Manufacturing and Airworthiness. The ODA unit must complete and document its manufacturing and airworthiness activity on the summary activity report; an example is shown in appendix A, figure 10 of this order. Use of a similar form to report this information is also acceptable. Unless directed to do so more frequently, the ODA holder must submit this report to the OMT on a quarterly basis.
b. Alteration/Repair Activity. The ODA holder must submit reports of alteration or repair data approvals quarterly or as more frequently required by its OMT. The report should identify the make and model of product and a description of the approved repair or alteration.
c. Design Change Activity Reports. A TC ODA holder must provide quarterly reports to the OMT lead identifying any type design change approved by the ODA unit that did not require program notification. The report must include the information specified by the OMT.
d. Air Operator ODA Activity. For AO ODA, the ODA unit must document operational certification activity in a manner acceptable to the OMT. AO ODA with function codes 15080 and 15090 must submit a quarterly report listing each completed function code activity identifying: the aircraft registration number, the aircraft serial number, the registered owner’s information, and the task card description (if applicable).
3-17. Records. The ODA holder must ensure that the records described below are maintained. ODA holder records must be located within the United States. The ODA holder must also ensure
a. The following must be retained for the duration of the authorization: › (8) Any correspondence between the ODA holder and the OMT related to…
the records specific to the authorizations described in Chapters 8 through 15 of this order are maintained. The records may be kept by the ODA holder, its suppliers, or others, as agreed to by the OMT. Certification project files retained by the ODA holder must match the requirements for FAA offices as prescribed in FAA Order 8110.4 or FAA Order 8900.1 (as applicable). The ODA holder must also keep any records required for any certificates or authorizations it holds in addition to an ODA. At the OMT’s request, an ODA holder must make the records available for examination at any time without undue delay. The ODA holder must make the records usually maintained by suppliers available at its facility for FAA inspections when requested. In addition to FAA inspections, all records associated with AO ODA types for function codes 15080 and 15090 must be in an electronic format (acceptable to the OMT) and readily available for transmittal to any FAA Flight Standards Office responsible for the aircraft. These records requirements and procedures must be stipulated in the ODA Procedures Manual. The ODA holder must identify all records and submit them to the OMT lead as soon as the ODA is surrendered or terminated.
a. The following must be retained for the duration of the authorization:
(1) Any records generated and maintained under the designated alteration station (DAS), delegation option authorization (DOA) or special federal aviation regulation (SFAR) 36 regulations.
(2) For approvals and certificates issued under the ODA:
(a) The application and data required to be submitted by the regulations.
(b) The data and records documenting the ODA unit’s approval, determination of compliance, or review.
Note: Airworthiness certificates and approvals need only be retained for two years, except those issued in support of a type certification project, which must be retained indefinitely. See AO ODA, Chapter 15 for additional records requirements.
(3) A list of the products and/or articles for which ODA unit members have issued a certificate or approvals. For AO ODA with function codes 15080 and 15090 the list must include the items specified in Chapter 15 of this order.
(4) The names, responsibilities, qualifications, and example signature of the individuals who perform, or have performed, functions for the ODA unit.
(5) A copy of each manual approved by the ODA unit.
(6) Training records for ODA unit members and ODA administrators.
(7) All other records required by the approved ODA procedures manual.
(8) Any correspondence between the ODA holder and the OMT related to functions or activity performed with the authorization.
c. FAA Notification. For any approvals, authorizations, certificates… › (6) Is subject to 14 CFR part 91, § 91.415 action by the FAA.
(9) The procedures manual, including all revisions.
b. The following must be retained for five years:
(1) Records of the ODA holder’s self-audits and implementation of corrective action.
(2) Records of any reported service difficulties associated with any design approval or certificate (including TCs, STCs, PMA by test and computation, and repair and alteration data) issued under the ODA.
c. Records Storage and Identification. The OMT and the ODA holder must agree on how to store and identify all required records for future retrieval. Certification records should be arranged by project number for easy retrieval. All ODA documentation and data must be consistent with that required by the FAA for its own records and organized in a manner that is compatible with the FAA records control system described in FAA Order 1350.14, Records Management. For AO ODA type with function code 15080 and 15090 the records storage and identification procedures must be in an electronic format (acceptable to the OMT).
3-18. Data Review and Service Experience. The ODA holder must provide continued support for approvals or certificates issued under ODA procedures in accordance with 14 CFR §§ 183.63 and 183.65. Procedures for monitoring service information, investigation, and FAA notification must be included in the procedures manual.
a. Other Data Reporting Requirements. An ODA holder must comply with all existing applicable reporting requirements in the FAA regulations, such as 14 CFR 21.3.
b. Service Difficulty Monitoring. The ODA holder must monitor any service information available to it that is associated with approvals or certificates it holds that were issued under its ODA authority.
c. FAA Notification. For any approvals, authorizations, certificates issued or acceptance of instructions for continued airworthiness (ICA) under an ODA, the ODA holder must notify the OMT lead of any item it identifies that:
(1) Might result in an unsafe condition.
(2) Requires corrective action.
(3) Does not meet the airworthiness standards.
(4) Is an error made when issuing an operational approval.
(5) Does not meet applicable operational certification requirements.
(6) Is subject to 14 CFR part 91, § 91.415 action by the FAA.
Note: Potentially unsafe conditions require 24 hour notification. All others require 72 hour notification. A notification due on Saturday, Sunday, or holiday may be delivered on the next working day.
Chapter 3. Qualifications, Responsibilities, and Authority › 3-19. Corrective Action.
d. Investigating Safety Concerns.
(1) For any approvals, authorizations, certificates issued or ICA acceptance under an ODA, the ODA holder must investigate potentially unsafe, or non-compliant conditions in any product, article, authorization, or certificate, as required by the FAA. As part of this investigation, the ODA holder must:
(a) Determine the cause of the condition.
(b) Determine whether the problem is systemic or isolated.
(c) Review the procedures that led to the approval and determine if the procedures are adequate and if qualified ODA unit members performed them.
(d) Develop and propose corrective action acceptable to the OMT.
(2) An ODA holder must submit its determination of the cause of the condition and proposed corrective action within 30 calendar days from FAA notification, or as required by the OMT. The ODA holder must submit any information it has to support FAA corrective action if further action is necessary to ensure the safe operation of the product.
(3) For AO ODA types with function codes 15080 and 15090, whenever the Administrator finds that revisions to an ODA-approved § 91.409(f)(4) program are required for continued adequacy of the program, the ODA holder may be requested to review and assess all similar programs and make the necessary revisions to all the affected programs. The ODA holder may not petition the Administrator to reconsider on behalf of the owner or operator of the aircraft.
e. Suspending Operational Approvals. The OMT may notify and direct the ODA holder to suspend issuance of any operational authorizations and certificates until the ODA holder implements any corrective action required by the OMT.
f. Aircraft Inspection Program Review. AO ODA with function code 15080 must cooperate with any § 91.415 procedures as directed by the OMT on programs approved by the AO ODA holder. Any inquiries from FAA field offices concerning these programs will be forwarded to the OMT for coordination. The ODA unit must provide access to or copies of all records and data associated with the ODA project of any program approved by the ODA holder to any FAA field office as directed by the OMT in order to assist the Administrator in making the findings of adequacy of such programs.
3-19. Corrective Action. The ODA holder must implement corrective action to address any unsatisfactory conditions with the organization’s ODA procedures or performance as required by the OMT. The ODA holder must show a willingness to do this and be proactive in incorporating
Chapter 3. Qualifications, Responsibilities, and Authority › 3-22. Inspection Unit Members at Suppliers.
improvements into its ODA system. Failure to implement needed corrective action is reason for the FAA to suspend or terminate an ODA.
a. Regulatory Non-compliances. The ODA holder must provide corrective action for any violations of the regulations as required by the OMT.
b. Other Conditions Requiring Correction. The ODA holder must submit to the OMT the determination of the cause of the condition and proposed corrective action as required by the OMT.
3-20. Activity Outside The United States. The ODA holder must notify the OMT prior to performing any function in a foreign country. To determine if the OMT must notify a civil aviation authority (CAA) of an ODA holder’s activity in the CAA country, check the individual bilateral agreement for the country. Prior CAA coordination of ODA holder activity is required for those countries with which the United States does not have a bilateral agreement. The OMT will coordinate technical assistance support from a CAA only when that CAA restricts the use of ODA holder personnel. When required, the OMT will develop an undue burden decision paper as described in FAA Order 8100.11, Decision Paper Requirements for Undue Burden and No Undue Burden Determinations Under 14 CFR part 21 for Production and Export Airworthiness Approvals. Further information about working with bilateral partners on type validation activities can be found in FAA Order 8110.52, Type Validation and Post Type Validation Procedures. See additional limitations for AO ODA holders in Chapter 15.
3-21. Use of FAA Forms. The ODA holder must use FAA forms to document the certification process if an applicable FAA form exists. Refer to appendix E of this order for FAA orders which contain the applicable forms. If necessary, forms may be altered only by striking through existing text entries and adding additional entries or supplemental information as required. The ODA holder’s procedures manual must contain a copy of the forms used within and instructions for completion of forms. If instructions by reference are not appropriate, the procedures manual should specify how the forms are to be completed.
3-22. Inspection Unit Members at Suppliers. ODA unit members employed by and located at a supplier facility must perform their authorized functions at that supplier’s facility, or a sub-tier facility for that same supplier. The unit member’s work must support the same products or articles produced by the supplier for the supported ODA holder.
Chapter 4. Application, Selection, and Appointment › 4-1. Pre-Application Communication.
Chapter 4. Application, Selection, and Appointment
4-1. Pre-Application Communication. A prospective ODA applicant must discuss with the FAA its desire to obtain an ODA before formal application. The FAA issues ODAs at its discretion. Each prospective applicant must confirm whether the FAA needs to appoint the organization and whether the FAA has the resources to manage its organization. An organization must begin discussions with the appropriate appointing offices (as defined in figure 4-1 of this order) before preparing the application contents. The appointing office must inform the applicant if the FAA does not need the authorization or have the resources to manage the authorization. The appointing offices must give applicants feedback on their proposed organizational structure to determine if it is adequate before they submit the application.
Figure 4-1. Appointing/Managing Offices
If the application is for:
And the applicant seeks:
Then the appointing office is:
And the evaluation panel also includes these managing offices:
And the lead managing office is:
TC ODA ACO MIDO AEG ACO
PC ODA MIO MIDO MIDO
TSOA ODA MIO MIDO MIDO
STC ODA ACO MIDO AEG ACO
MRA ODA Only data approval functions
ACO ACO ACO
MRA ODA Both airworthiness and data approval functions
FSO ACO FSO
MRA ODA Only airworthiness functions
FSO FSO FSO
PMA ODA Only airworthiness or production functions
MIO MIDO MIDO
PMA ODA Both engineering and airworthiness functions
ACO MIDO AEG ACO
AKT ODA AFS-630 N/A AFS-630
AO ODA FSO FSO FSO
FAA Offices: ACO - Aircraft Certification Office AEG - Aircraft Evaluation Group MIO - Manufacturing Inspection Office FSO - Flight Standards Office (includes Certificate Management Office) MIDO - Manufacturing Inspection District Office (includes Certificate Management Office, Certificate Management Unit, and Manufacturing Inspection Satellite Office)
4-2. Application. › g. A draft procedures manual that includes the information required by…
5/16/13 8100.15B
4-2. Application. Applications must be submitted to the appropriate appointing office as shown in figure 4-1 of this order. If an applicant is applying for more than one type of ODA that will involve multiple appointing offices, they should coordinate with all appropriate appointing offices prior to submitting its application. The appointing offices will establish a lead office responsible for accepting the application and conducting the evaluation. An appointing manufacturing inspection office (MIO) may delegate selection and appointment responsibilities to the manufacturing inspection district office (MIDO). Each application must include:
a. FAA Form 8100-13, ODA Statement of Qualifications, (appendix A, figure 1 of this order).
b. A cover letter stating the authority and limitations requested for the authorization, including the products and/or articles for which the authorization will be used. The cover letter must also contain a brief statement describing the applicant’s eligibility under 14 CFR 183.47.
c. A detailed description of how the applicant meets the eligibility and qualification requirements defined in paragraphs 3-4 and 3-5 of this order, and the specific eligibility requirements defined in Chapters 8 through 15 of this order.
d. A detailed description of the applicant’s proposed ODA setup, including the ODA holder’s organizational structure, the ODA unit’s relationship to the applicant’s organization, and facilities.
e. The ODA administrator’s name, experience, and qualifications in a resume that clearly demonstrates that the proposed ODA administrator meets the qualifications of Chapter 3 of this order.
f. A list of the proposed ODA unit members and information outlining the experience, qualifications, proposed functions, and limitations of each ODA unit member.
(1) The applicant must evaluate the proposed ODA unit members to determine that they meet all qualifications before application. The applicant must use a process that is similar to that used by the FAA to evaluate designee applicants. See FAA Order 8100.8. Proposed ODA unit members that are existing designees need not be evaluated if they will be performing the same functions as under a current designation.
(2) For a new AO ODA, the applicant must evaluate proposed ODA unit members to determine if their experience and expertise are sufficient to support the proposed functions. The applicant should develop and document in the procedures manual a process for evaluation that is similar to that used by the FAA to evaluate designee applicants. See FAA Orders 8100.8 or 8900.1. The OMT makes the final determination of whether or not the applicant’s process is acceptable based on the functions the unit members will be performing.
g. A draft procedures manual that includes the information required by paragraph 3-9 of this order, and the specific information outlined in the procedures manual example in appendix B and in Chapters 8 through 15 of this order.
4-3. Selection Process.
a. Initial Application Screening.
(1) If an application passes the initial screening, the appointing… › (b) Technical specialists from all areas proposed for the authorization.
(1) The appointing office will screen each application to verify that:
(a) All required documentation is complete.
(b) Appointing the organization will be a benefit to the FAA.
(c) The FAA has the resources to manage the organization and its activity.
(d) The organization meets the eligibility requirements of 14 CFR 183.47 and Chapters 8 through 15 of this order.
(2) If the FAA does not need, or does not have the resources to manage a particular ODA applicant, the appointing office must prepare a denial letter for the office manager’s signature. (See appendix A, figure 4 of this order.) Further, if the appointing office determines that the applicant is ineligible, it prepares a denial letter. The appointing office must inform the applicant if it needs additional information to determine the applicant’s eligibility.
b. Evaluation Panel (EP) Makeup.
(1) If an application passes the initial screening, the appointing office must organize an evaluation panel (EP) of FAA personnel that will evaluate the application. An appointing office representative will manage the EP. The EP will consist of the following:
(a) Representatives from each relevant FAA organization in figure 4-1 of this order.
(b) Technical specialists from all areas proposed for the authorization.
Note 1: The EP may consist of the prospective OMT members for the organization, or the appointing office may use a standard panel for all applicants. See paragraph 5-2 of this order for information about the OMT.
Note 2: The appointing office must inform the appropriate regional (AFS only) and headquarters office representative(s) of all ODA applications it receives. Regional and headquarters specialists from AIR-100, AFS-600, or AFS-800 may participate in evaluation panel activity (such as review and comment on the ODA holder’s procedures manual) as they determine necessary, but are not considered official EP members. Each regional/headquarters office will determine its participation based on the desired functions and the need to be involved in the appointment decision.
d. Evaluation of the Application. The EP will review each application… › (2) Interviews.
5/6/13 8100.15B
(2) The EP must be qualified, familiar with the functional areas of delegation requested, and experienced with the applicable certification processes.
c. Appointment Considerations. The EP must consider the following to determine whether the FAA will grant the ODA:
(1) The applicant must employ or have available a staff of qualified personnel appropriate to the authorization requested.
(2) The applicant must have adequate resources, facilities in the United States, equipment, tools, and manuals appropriate for the authorization.
(3) The ODA administrator(s) and unit must possess integrity, sound judgment, and a cooperative attitude.
(4) The organization must have a history of enough work to justify the appointment.
(5) The FAA must have the appropriate resources to oversee, manage, and support the appointment.
(6) The ODA administrator(s) must meet the qualifications of paragraph 3-5a of this order.
(7) The procedures manual must contain the information required by the regulations and this order.
d. Evaluation of the Application. The EP will review each application to determine whether the applicant qualifies for the authorization. The EP will thoroughly evaluate the application, the proposed procedures manual, the applicant’s qualifications, the proposed ODA administrator’s and ODA unit members’ qualifications, and the organization’s resources and structure. The EP must verify the accuracy and authenticity of the information in the application. The EP must verify that the information in the application and procedures manual complies with all applicable regulations and this order.
Note 1: If an ODA holder’s authority will include any authority with respect to part 34 or 36, the EP must coordinate with AEE-100. AEE-100 must concur with any part 34 or part 36 authority granted to the organization or individual unit members.
Note 2: If an ODA holder’s authority will include ICA review and acceptance authority, the AEG EP member is responsible for determining eligibility and for reviewing the applicant’s process for accepting ICA.
(1) Evaluation Panel Documentation. The EP must create and maintain documentation such as meeting minutes, email, or other correspondence about its evaluation.
(2) Interviews. The EP may interview the proposed ODA administrator, ODA unit members, or ODA applicant’s management to verify the information in the application and
h. Functioning of the Appeal Panel. The appeal panel must determine if… › (1) The documentation in the applicant’s file,
5/6/13 8100.15B
determine whether the ODA applicant understands the requirements its organization must meet. While interviewing staff members, the EP may evaluate their knowledge of the certification procedures and technical responsibilities for which the ODA holder will be responsible.
(3) Site Visits. The EP may conduct site visits to evaluate an organization’s facilities and abilities. Although existing certificate holders usually have existing facilities known to the FAA that may not require inspection, the EP will usually need to inspect consultant groups’ facilities to verify they have the facilities necessary for the authorization.
(4) Procedures Manual Review. The EP must approve each applicant’s procedures manual prior to appointment. A single AEG EP office manager may approve the applicant’s procedures manual on behalf of all other AEG EP office managers. The evaluation panel must coordinate any procedures manual language addressing certification project notification (CPN) requirements with the accountable directorate standards staff. During an evaluation, the EP must review the proposed procedures manual and ensure that it:
(a) Contains the information required by paragraph 3-9 of this order.
(b) Contains procedures that comply with all orders pertaining to the functions described.
e. Denial of ODA Applications. The appointing office will notify the applicant if it denies its application. The appointing office must send the applicant the denial in writing via registered mail within 30 days of the decision. The denial letter must explain the reasons for the denial and detail what steps the applicant must take before the FAA will reconsider the application. (See appendix A, figure 4 of this order for an example of the ODA denial letter.)
f. Appeals. If denied, an applicant may usually appeal the FAA decision in writing and request a review by an appeal panel. Denial decisions based on failure to attend required training, lack of benefit to the FAA or the FAA’s inability to manage the organization may not be appealed. An applicant must submit its appeal within 60 calendar days of receiving notification of the denial.
g. Appeal Panel. An appeal panel will consist of at least two managers and an engineer or inspector or flight test pilot from the geographic directorate, manufacturing inspection office (MIO), and/or flight standards regional office (RO) as appropriate for the application. The appeal panel will consider all available information and may interview the applicant, applicant’s staff, and evaluation panel personnel. The appeal panel may also invite other persons as needed at its deliberations. The appeal panel will reach a decision by consensus and all decisions are final.
h. Functioning of the Appeal Panel. The appeal panel must determine if the appointing office conducted the appointment process properly. If the appeal panel finds discrepancies, it must take appropriate actions to ensure the integrity of the appointment process. To determine whether the appointing office conducted the appointment process properly, the appeal panel may interview members of the EP and review:
(1) The documentation in the applicant’s file,
Chapter 4. Application, Selection, and Appointment › 4-4. Appointment.
5/6/13 8100.15B
(2) The EP’s written justification for the denial, and
(3) Other information it determines appropriate.
Note: The appeal panel must complete its deliberations within 45 calendar days from the date of the appeal, and must document its decision. Each panel member must sign the decision before the panel sends it to the directorate or RO manager. The directorate or regional office manager will notify the applicant and appointing office of the appeal panel’s decision by registered mail within 15 calendar days of the appeal panel’s decision.
i. Appeal Panel Decisions. The appeal panel may:
(1) Uphold the previous decision;
(2) Override the previous decision with a new decision and provide appropriate justification; or
(3) Request that any part of the appointment process be repeated citing new information that the EP must review, or issue additional instructions and clarifications to the EP. The appeal panel may direct that the previous EP review the application, or it may direct the appointing office to appoint a new EP.
4-4. Appointment. If an EP approves an application, the OMT and ODA holder must prepare an MOU, as described in paragraph 3-7 of this order. At least one member of the applicant’s senior level management, typically the organization’s chief executive officer, must sign the MOU. After completing the selection process (including getting the MOU signed) and notifying its directorate or regional office manager, the appointing office will provide the applicant a letter of designation. The letter of designation must be signed by all of the OMT’s office manager(s), except that single OMT AEG office manager may sign the letter of designation on behalf of any other OMT AEG office managers. The letter of designation must note the organization, main operating location, types of ODA, authorization number, and expiration date for the ODA. The ODA procedures manual must include the functions and limitations of the authorization. The scope of the limitations may be in any form appropriate to the authorization. For example, limitations may be imposed based on a lack of certain experience, equipment, or limited to certain types of aircraft. See appendix A, figure 3 of this order for a sample letter of designation. New ODAs will be granted for two years.
Continue reading ↓ 120 of 730 passages shown