Order 8100.8D Designee Management Handbook
This document is cancelled. It may have been replaced. Check the official source before relying on it.
Text read by OCR from a scanned file (1 of 261 pages). Check the original, as some words may be misread.
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION ORDER
National Policy 8100.8D
Effective Date:
10/28/2011
SUBJ: Designee Management Handbook
This order is a comprehensive publication establishing policy and procedures for the selection, appointment, orientation, training, oversight, renewal tracking, and tennination ofcertain representatives of the Administrator, under the cognizance of the Aircraft Certification Service and Flight Standards Service. The information contained in this order is the result ofan ongoing effort to improve the processes involving representatives ofthe Administrator and to update the procedures as appropriate.
~~~~ Dorenda D. Baker Director Aircraft Certification Service
Distribution: Electronic Initiated by: AIR-100/200
Table of Contents
Paragraph Page
Chapter 1. Introduction
100. Purpose … 1-1 101. Audience … 1-1 102. Where To Find This Order … 1-1 103. Cancellation … 1-1 104. Explanation of Changes … 1-1 105. Compliance Date … 1-2 106. General Authority … 1-2
Chapter 2. AIR Roles and Responsibilities
200. General … 2-1 201. Training … 2-1 202. Designee Process Coordinator … 2-1 203. Advisor … 2-2 204. Appointing Office Manager … 2-3 205. Evaluation Panel … 2-4 206. Appeal Panel … 2-4 207. Evaluator … 2-5 208. Managing Office Manager … 2-5
Chapter 3. AIR Designee Authority and Responsibilities
300. General … 3-1 301. Manufacturing Designee Authority … 3-2 302. Cross-Utilization of DARs … 3-3 303. Manufacturing Designees — International Operating Procedures … 3-4 304. Engineering Designee — DER Authority … 3-4 305. Engineering Designee Appointments — Company/Consultant Categories … 3-4 306. Engineering Designations … 3-5 307. Engineering Designees — Special Designations … 3-7 308. Engineering Designees — Special Authorizations … 3-10 309. Engineering Designees — Delegated Functions/Authorized Areas/Limitations/Specific Functions … 3-11 310. Engineering Designees — International Operating Procedures … 3-12
iii
Paragraph Page
Chapter 4. AIR Application Process
400. General … 4-1 401. Application Package … 4-1 402. Regulatory Appointment Criteria … 4-2 403. Technical Appointment Criteria — General … 4-2 404. Technical Appointment Criteria — Specialized — DER … 4-3 Table 4-1. Technical Appointment Criteria — Specialized — DER … 4-3 405. Interface Appointment Criteria — DER … 4-15 406. Standardization Appointment Criteria … 4-16 407. FAA Employee Applicants … 4-16 408. Multiple Appointments … 4-16 409. Supplier DMIR Applications … 4-17 410. Appointment of DMIRs Outside the United States … 4-18 411. Appointment of DARs Outside the United States … 4-18 412. Appointment of DERs Outside the United States … 4-18
Chapter 5. AIR Designee Appointment Process
500. General … 5-1 501. Initial Application Processing … 5-1 502. Advisor’s Evaluation of the Application … 5-2 503. Purpose and Makeup of the EP … 5-3 504. EP Review of the Application … 5-4 505. Administrative Requirements … 5-5 506. DER Candidate Identification … 5-6 507. DER Candidate Procedures … 5-7 508. Requests for Multiple Appointments, Dual Appointments, Expanded Authority, and Transfer … 5-7
Chapter 6. AIR Appeal Process
600. General … 6-1 601. Appeal Panel … 6-1 602. Scope of Appeal Panel Authority … 6-1 603. Functioning of Appeal Panel … 6-1
iv
Paragraph Page
Chapter 7. AIR Designee Orientation
700. General … 7-1 701. General Designee Orientation … 7-1 702. DER Orientation … 7-2 703. DMIR Orientation … 7-3 704. DAR Orientation … 7-5
Chapter 8. Designee Training
800. General … 8-1 801. Types of Designee Training Seminars … 8-1 802. Initial Seminars … 8-1 803. Recurrent Seminar … 8-3 804. Additional Provisions … 8-5 805. Seminar Attendance Records … 8-5 806. Seminar Registration … 8-5
Chapter 9. AIR Designee Oversight
900. General … 9-1 901. Responsibilities … 9-1 902. Manufacturing DMIR/DAR Oversight (Supervision, Monitoring, and Tracking) … 9-2 903. DMIR/DAR Geographic Restrictions … 9-4 904. DER Oversight … 9-5 905. Minimum Levels of DER Oversight … 9-9 906. FAA Form 8110-3 Submittal … 9-10 907. DER Candidate Oversight … 9-10 908. Designee Information Network … 9-11
Chapter 10. AIR Designee Renewal
1000. AIR Designee Renewal … 10-1 1001. Duration of Appointments … 10-1 1002. DMIR and Manufacturing DAR Renewal Guidelines … 10-2 1003. Executive-level DMIRs/DARs … 10-4 1004. Executive-level DMIR/DAR Evaluation Considerations … 10-4 1005. DER Renewal Procedures … 10-5 1006. Executive-level DER Evaluation Considerations … 10-8
v
Paragraph Page
Chapter 11. Suspension, Reinstatement, and Termination of AIR Designations
1100. General … 11-1 1101. Suspension … 11-1 1102. Suspension Process and Documentation … 11-1 1103. Suspension Requirements … 11-1 1104. Reinstatement from Suspension … 11-2 1105. Termination … 11-2 1106. Cause for Termination of Designations … 11-3 1107. Voluntary Termination Procedures for Designees … 11-4 1108. Termination Procedures of a DMIR, DER, or DAR … 11-4 1109. Coordination of Termination Decisions … 11-6 1110. Designee Information Network Status … 11-6
Chapter 12. AIR Designee File Management
1200. Establishment and Maintenance of Files … 12-1 1201. Designee File Content … 12-1 1202. Designee File Management … 12-1
Chapter 13. Amateur-Built and Light-Sport Aircraft Certification Functions
1300. Purpose … 13-1 1301. Function Code Descriptions … 13-1 1302 Limitations … 13-1 1303. National Examiner Board (NEB) … 13-1 1304. Selection and Appointment Process … 13-3 1305. Qualification Criteria … 13-3 1306. Training Requirements … 13-5 Figure 13-1. Amateur-Built and Light-Sport Aircraft Supplemental
Information … 13-7
vi
Paragraph Page
Chapter 14. AFS DAR Procedures
1400. General … 14-1 1401. General Qualifications … 14-1 1402. Specialized Experience Required for Maintenance Functions … 14-1 1403. Specialized Experience Required for Data Management Functions … 14-4 1404. National Examiner Board (NEB) Process … 14-5 1405. Application Procedures … 14-6 1406. Authorized Functions and Codes and Their Usage … 14-6 1407. Former FAA Employee Applications … 14-7 1408. Applicant Notification … 14-7 1409. General Designee Orientation … 14-7 1410. Designee Responsibilities … 14-7 1411. DAR Geographical Restrictions … 14-8 1412. Designee Information Network/Program Tracking and Reporting System … 14-9 1413. Compliance and Enforcement … 14-9 1414. Designee Renewal … 14-9 1415. Termination of Designations … 14-10
Chapter 15. Authorized Functions
1501. Authorized Functions and Codes … 15-1 1502. Function Code(s) Usage … 15-1 Table 15-1. DMIR Authorized Functions … 15-1 Table 15-2. DAR-F Authorized Functions … 15-3 Table 15-3. DAR-T Authorized Functions … 15-6 Table 15-4. DAR-F and DAR-T Authorized Functions … 15-8
vii
Page
Appendix A. Application Package
Figure A-1. Sample FAA Form 8110-14, Statement of Qualifications
(Reduced Size) … A-1 Figure A-2. Sample Letter to a DER Applicant … A-2 Figure A-3. DER Application Evaluation … A-3 Figure A-4. DMIR/DAR Application Evaluation … A-35
Appendix B. Appointment/Evaluation Documents
Figure B-1. Designee Appointment Tracking Document … B-1 Figure B-2. Designee Multiple Appointment, Dual Appointment,
Expanded Authority, and Transfer Tracking Document … B-4
Appendix C. Orientation
Figure C-1. Sample Designee Acknowledgment of Responsibilities … C-1
Appendix D. FAA Responses for Appointment
Figure D-1. Sample Acknowledgment of Receipt of Application … D-1 Figure D-2. Sample Notification Application Forwarded to Evaluation
Figure D-3. Sample Notification Application Not Forwarded to Evaluation
Panel … D-2
Panel … D-3 Figure D-4. Sample Notification of Denial Letter … D-4 Figure D-5. Sample Notification of Appointment as a DER … D-5 Figure D-6. Sample Notification of Identification as a DER Candidate —
Company … D-7 Figure D-7. Sample Notification of Identification as a DER Candidate —
Consultant … D-9 Figure D-8. Sample Notification of Appointment as a DMIR/DAR … D-11 Figure D-9. Sample FAA Form 8000-5, Certificate of Designation
(Reduced Size) … D-13
viii
Page
Appendix E. AIR Documents
Figure E-1. DMIR/DAR Summary Activity Report … E-1 Figure E-2. Sample Letter Authorizing Data Approval for Repairs and
Alterations … E-2 Figure E-3. Sample FAA Form 8110-29, DER/FAA Interaction Tracking
Form … E-3 Figure E-4. Sample FAA Form 8110-30, DER Performance Evaluation
Form … E-5 Figure E-5. Sample Notification to a DMIR or Company DER of
Suspension … E-7 Figure E-6. Sample Notification to a Supplier DMIR of Suspension … E-8 Figure E-7. Sample Notification to a DAR or Consultant DER of
Suspension … E-9 Figure E-8. Sample Notification to a DMIR or Company DER of
Reinstatement from a Suspension … E-10 Figure E-9. Sample Notification to a Supplier DMIR of
Reinstatement from a Suspension … E-11 Figure E-10. Sample Notification to a DAR or Consultant DER of
Reinstatement from a Suspension … E-12
Appendix F. FAA Documentation for Termination
Figure F-1. Sample Notice of Termination of a DAR/Consultant DER … F-1 Figure F-2. Sample Notice to a Production Approval Holder on
Termination of a DMIR … F-2 Figure F-3. Sample Notice of Termination of a Company DER … F-3
ix
Page
Appendix G. AFS Documents
Figure G-1. Sample FAA Form 8110-28, Application and Statement of
Qualification (DME/DPRE/DAR-T) … G-1 Figure G-2. Sample Certificate of Authority Letter for DAR —
Figure G-3. Sample Certificate of Authority Supplement, Delegated
Maintenance (DAR-T) … G-10
Functions and Limitations (DAR-T) … G-12 Figure G-4. FAA Geographic Boundaries — Flight Standards Service … G-13
Appendix H. Manufacturing Checklists - Witnessing
Figure H-1. Manufacturing Checklist for Up To an 18-Month
Witnessing Cycle … H-1 Figure H-2. Manufacturing Checklist for Aligning the Witnessing Cycle to the
Principal Inspector Facility Evaluation Cycle … H-4
Appendix I. Administrative Information
1. Distribution … I-1 2. Background … I-1 3. Authority to Change This Order … I-1 4. Forms, Letters, and Formats … I-1 5. Information Currency … I-1 6. Deviations … I-2 7. Records Management … I-2
Appendix J. Definitions … J-1
Appendix K. Acronyms … K-1
Appendix L. FAA Form 1320-19, Directive Feedback Information … L-1
x
Chapter 1. Introduction
100. Purpose. This order establishes the Federal Aviation Administration (FAA) procedures to be used by the Aircraft Certification Service (AIR) and Flight Standards Service (AFS) for managing the FAA’s representatives of the Administrator (designee) program. In addition, this order provides geographic restriction procedures and authorized designee functions. These procedures are designed to ensure they are applied in an unbiased manner to all qualified private persons. Specific designee procedures covered in this order include the following areas:
a. FAA roles and responsibilities.
b. Initial selection and appointment.
c. Orientation, including designee authority and responsibilities.
d. Training.
e. Oversight.
f. Renewal.
g. Termination and appeals.
101. Audience. All FAA employees who oversee private persons acting as representatives of the Administrator and those persons acting as representatives of the Administrator for the purpose of aircraft certification.
102. Where To Find This Order. You can find this order at http://www.faa.gov/regulations_policies/orders_notices/.
103. Cancellation. This order cancels FAA Order 8100.8C, Designee Management Handbook, dated May 7, 2007, and its associated changes, and FAA Order 8130.33, Designated Airworthiness Representatives: Amateur-Built and Light-Sport Aircraft Certification Functions.
104. Explanation of Changes. This revision of the order—
a. Places FAA Order 8100.8 in the format outlined in FAA Order 1320.1E, FAA Directives Management.
b. Incorporates information previously found in FAA Order 8130.33, Designated Airworthiness Representatives: Amateur-Built and Light-Sport Aircraft Certification Functions.
c. Sets a compliance date for advisor recurrent training.
d. Adds specific requirements for data entry into the Designee Information Network (DIN).
e. Deletes the requirement for a geographic expansion form for Designated Airworthiness Representatives (DAR).
f. Directs applicants to the FAA website for application forms.
g. Clarifies the use of designated manufacturing inspection representatives (DMIR) and DARs for TC/STC applicants.
h. Updates policy for DMIRs outside the United States.
i. Authorizes the local office to levy training requirements as necessary.
j. Changes “one on one” meeting to “performance review” for manufacturing designees.
k. Changes witnessing requirements for manufacturing designees.
l. Explains the new DIN process and DIN renewal process.
m. Addresses termination for failure to complete recurrent training.
n. Changes the requirement for record management.
o. Authorizes the listing of all function codes.
p. Revises the manufacturing application.
q. Creates criteria for issuing FAA Form 8130-31, Statement of Conformity – Military Aircraft.
r. Creates new appointment tracking documents.
s. Creates a new manufacturing Summary Activity Report.
t. Creates new manufacturing witnessing cycle change checklists.
105. Compliance Date. This order is effective when signed. The compliance date of this order is 60 days after the order is signed.
106. General Authority.
a. Title 49 of the United States Code 44702(d) empowers the Administrator to “...delegate a qualified private person, or to an employee under the supervision of that person, a matter related to the examination, testing, and inspection necessary to issue a certificate, and issuing the certificate.” Title 14 of the Code of Federal Regulations (14 CFR) part 183, Representatives of the Administrator, prescribes the requirements for designating private persons to act as representatives of the Administrator for the purpose of issuing airmen and aircraft certificates. Part 183, subpart B, Certification of Representatives, empowers the FAA to select designees from qualified persons who apply by letter accompanied by a statement of qualifications. The
delegations are limited in scope in that all requirements, policy, direction, and interpretations must reside with the Administrator.
b. Section 183.29, Designated Engineering Representatives, defines the types of designated engineering representative (DER) appointments in the following technical disciplines:
(1) Structural engineering.
(2) Powerplant engineering.
(3) Systems and equipment engineering.
(4) Radio engineering.
(5) Engine engineering.
(6) Propeller engineering.
(7) Flight analyst.
(8) Flight test pilot (FTP).
(9) Acoustical engineering.
c. Section 183.31, Designated Manufacturing Inspection Representatives, defines the privileges of a DMIR appointment.
d. Section 183.33, Designated Airworthiness Representative, defines the privileges of a DAR appointment.
e. Section 183.15, Duration of Certificates, defines the duration of the above appointments and identifies that the appointments are subject to periodic renewal.
f. Section 183.15(b) identifies the causes for termination of a designation made under part 183.
g. It is essential that designees be familiar with, and have ready access to, all appropriate FAA publications and documents.
h. A designation is a privilege, not a right, and not every qualified applicant will be granted a designation. The FAA is SOLELY responsible for determining if there is sufficient need to justify the appointment of a designee, and that there are adequate FAA resources available to manage the designee. If either of these conditions cannot be met, or for any other reason that the Administrator prescribes, the designee appointment WILL NOT be made. Subsequent to appointment, a designation may be terminated in accordance with § 183.15(b), chapter 11 of this order, and/or FAA Order 8900.1, Flight Standards Information Management System (FSIMS).
i. The FAA is responsible for determining when the services of a designee may be used.
(1) Consistent with general principles of management, the oversight portion of this order addresses setting performance expectations, monitoring performance, and taking any appropriate corrective action. Manufacturing aviation safety inspector (ASI) certification functions will be delegated to the fullest extent practical, but not to the extent an advisor’s technical skills are jeopardized.
(2) Designees must perform only those functions for which they have been authorized, including any unique function(s) specifically authorized on a case-by-case basis. All certification functions identified in this order will be performed on behalf of the FAA and not on behalf of the aviation industry. In addition, a designee is not considered an employee of the U.S. Government and is not federally protected for the work performed or the decisions made as a designee. The limits of Federal protection for FAA employees are defined by Title 28, United States Code § 2679.
j. Section 44702(d) states that when delegation to a qualified private person is made, or to an employee under the supervision of that person, the designee is subject to regulations, supervision, and review. Designee oversight constitutes the supervision and review of designees and is the process by which the FAA compares designee performance to stated expectations.
k. Designee oversight is the process which the FAA uses to manage the designee’s performance as a representative of the Administrator. This process provides the FAA the opportunity to identify and correct any designee performance deficiencies. When a performance deficiency is communicated to the designee, the FAA initiates corrective actions that will result in satisfactory work performance by the designee for future activities.
l. Designee renewal is made subject to the FAA’s determination of the continued need, ability to manage, and continuous satisfactory designee performance, which in turn justifies the continuation of the appointment and designee renewal.
m. The FAA will terminate a designee when it determines that the appointment is not warranted under chapter 11 of this order. Designees are cautioned that because the appointment is a privilege and not a right, the FAA is authorized to terminate a designation in accordance with § 183.15(b).
n. The applicant does not have any appeal rights when there is no FAA need or resources to manage the designation. The managing office(s) should write a courtesy letter notifying the applicant that the FAA is not accepting applications for the requested delegation and that the applicant may reapply at a future date. Current designees may appeal in accordance with the guidelines in chapter 6, AIR Appeal Process, and chapter 11 of this order, or FAA Order 8900.1, vol. 13, chapter 5, section 3.
Chapter 2. AIR Roles and Responsibilities
200. General. This chapter describes roles and responsibilities of the designee process coordinator (DPC), advisor, appointing office manager, evaluation panel (EP), appeal panel, evaluator, and managing office manager in the selection, appointment, oversight, and tracking processes.
201. Training.
a. Initial Training. FAA employees managing designees will complete designee management training as specified by their service headquarters. AIR employees will accomplish training as specified in FAA Order 8000.93, Aircraft Certification Service National Technical Training Plan. ASIs, aviation safety engineers (ASE), and FTPs who have more than 12 months of experience working for the FAA but have not completed the required training may manage designees when assigned a mentor who has successfully completed training. The mentor and/or one of the managing office’s qualified ASIs, ASEs, or FTPs will provide guidance and be available to answer any designee management-related questions.
b. Recurrent Training. ASIs will complete online recurrent training once every 36 months after completion of initial training. ASEs and FTPs will attend the same recurrent seminars that their assigned designees attend once every 4 years after completion of initial training. A detailed description of the designee recurrent seminars is provided in chapter 8. ASEs and FTPs may satisfy the 4 year requirement by attending a DER seminar in the calendar year it is due. ASIs, ASEs, and FTPs currently managing designees must be compliant with this requirement by May 31, 2012.
c. Recording Training Completion. ASI, ASE, and FTP training will be recorded by their FAA organization, in the electronic Learning Management System (eLMS), through their training manager. Their office is responsible for tracking compliance, rather than the Engineering Procedures Office (AIR-110) or the Production and Airworthiness Division, (AIR-200).
202. Designee Process Coordinator. The DPC is responsible for initiating the formal selection and appointment process, and coordinating all subsequent FAA actions for the applicant. Specifically, the DPC will perform the following:
a. Prepare the applicant/designee file.
b. Prepare, coordinate, and send all letters to the applicant.
Note: For manufacturing, if the DPC is the aviation assistant or equivalent, they should not author any technical letters; however, they may perform the administrative functions.
c. Enter the information into the DIN at the beginning and completion of the process.
d. Ensure the applicant has provided all information required by this order.
e. Send the application package and file to the advisor for review.
f. Review the file after completion by the advisor to determine if the applicant is being recommended to an EP.
g. Schedule meetings, notify all parties involved, and provide copies of all necessary documentation. The DPC also may chair and/or facilitate EP meeting(s) and ensure all appropriate documents are in the designee file.
Note: For manufacturing, if the DPC is the aviation assistant or equivalent, they will not chair EP meetings. The appointing office manager or an ASI member to the EP will chair the meeting.
h. Prepare and coordinate appointment letters/certificates and send them to the applicant, or give the letters/certificates to the advisor for presentation or mailing to the applicant, as appropriate.
i. Prepare letters of denial or termination as directed in this order.
j. Inform the managing office manager of receipt of any denial decision appeals from the applicant.
203. Advisor. For the purpose of designee appointment, the advisor conducts a preliminary review of the application package and either denies or makes a recommendation to the EP. For the management of the designee, the advisor oversees the designee’s activity and is responsible for addressing, in a timely manner, questions from a designee concerning certification procedures or policies. For the purpose of renewal, the advisor is responsible for conducting a review of the designee. The advisor will accomplish the following:
a. Review the application package and designee file for completeness.
b. Maintain the designee file and ensure timely updates.
c. Review the application package for general qualifications and scope/specialty.
d. Consult the appropriate manager to determine the FAA’s need and ability to manage the applicant, if the applicant were to be appointed.
e. Document the justification for the appointment or denial.
f. Conduct a preliminary technical review of the application package and seek technical input from other FAA sources, as necessary.
g. Contact the applicant’s references, if required.
h. Contact the applicant at any point during the evaluation process for additional information and/or documentation.
i. Reduce the scope of the functions sought, or deny applications, when appropriate.
j. Recommend to the EP appointment or candidacy including any limitations.
k. Conduct initial orientation of the newly appointed designee or candidate.
l. Ensure that the designee signs the Designee Acknowledgment of Responsibilities.
m. Respond to questions from the designee concerning FAA-accepted methods of compliance and procedures for certification activity.
n. Permit the designee to exercise the appointment authority by performing authorized functions in certification activity.
o. Review technical compliance data from the designee or participate with the designee in certification activities, as appropriate.
p. Provide feedback to the designee concerning performance.
q. Identify and justify a minimum level of oversight for assigned designees.
r. Verify the designee’s completion of required training.
s. Review the designee’s performance as required by this order.
t. Renew the designee appointment as required by this order.
u. Participate, as needed, in activities supporting FAA decisions for termination of a designee appointment.
v. Enter data into the DIN as required by this order.
204. Appointing Office Manager. The appointing office manager’s responsibilities in the designee management process are to accomplish the following:
a. Determine the FAA’s need for the requested designation.
b. Determine that the FAA has the ability to manage the designation.
c. Determine the assignment of an advisor.
d. Select EP members.
e. Sign (or delegate signature authority) for all designee correspondence not generated electronically within the DIN.
f. Sign or coordinate on all designee appointments or candidacies after the EP decision has been reached.
g. Approve a minimum level of oversight for assigned designees and ensure that a minimum level of oversight is conducted for each designation.
h. Oversee and approve designee renewals.
205. Evaluation Panel. The purpose of the EP is to compare qualifications to the appointment criteria and to determine denial, candidacy, appointment, and delegated authority, as appropriate. The EP must consist of at least two individuals who are in the same discipline as the applicant and who are familiar with the selection and appointment process. The applicant’s assigned advisor may be a member of the EP. The EP will accomplish the following:
Note 1: The EP must consist of at least three individuals for applicants seeking specialized delegation for vintage aircraft. One from the Small Airplane Directorate and two who are in one of the requested vintage aircraft disciplines. For applicants seeking special vintage aircraft delegation for engines, the EP will also include a member from the Engine and Propeller Directorate. A representative of the Flight Standards office with knowledge of the applicant’s activity is also highly recommended.
Note 2: Management participation should be reserved for potential appeals; therefore, managers should not serve as EP members. A manager who serves as a member of an EP may not serve on any appeal panel for the same applicant.
a. Review the application package submitted by the advisor.
b. Interview the applicant or document the reasons why an interview was not necessary.
c. Reach consensus for each selection or appointment.
d. Document all meetings and sign all EP forms.
e. Give the completed documentation to the DPC for retention in the applicant’s file.
206. Appeal Panel. The appeal panel provides an avenue for the applicant to appeal the decision regarding a request for appointment as a designee. The decisions of the appeal panel are FINAL. The appeal panel will consist of at least three persons equivalent to the advisor level or above who were not involved in the original denial decision. The appeal panel will accomplish the following:
a. Determine if the appointment process was conducted properly and either upholds the previous decision, override that decision, or request that any part of the appointment process be repeated.
b. Make decisions by reviewing the documentation in the appellant’s file, the EP’s written justification, and any other information.
c. Invite other persons to be resources at its deliberations, when required.
d. Conduct any interviews, as necessary.
e. Initiate corrective action to prevent recurrence if discrepancies are found during the review of the EP decision.
f. Complete deliberations and reach a decision by consensus within 45 days from the date of the appeal.
g. Document and sign all appeal panel decisions.
207. Evaluator. The evaluator assists the advisor by providing technical specialist input during initial review and annual review of designee performance. The evaluator has a technical specialist background different from that of the advisor. The evaluator’s responsibilities are to provide the following:
a. Technical specialist input to the advisor during the application review process.
b. Orientation applicable to the evaluator’s technical specialty to the designee.
c. Technical specialist input to the advisor to support the scheduled renewal process for the assigned designee.
208. Managing Office Manager. The managing office manager is responsible for supervising, monitoring, training, and tracking assigned designees. The managing offices are the aircraft certification offices (ACO), certificate management offices (CMO), and manufacturing inspection district offices (MIDO) in their respective geographic areas. The managing office manager’s responsibilities are to ensure the following:
a. FAA employees are responsive to assigned designees when questions concerning FAA policy and procedures arise.
b. An assigned designee’s activities have at least a minimum level of oversight.
c. Designee performance is reviewed and recommendations concerning renewal are made in accordance with this order.
Intentionally Left Blank
Chapter 3. AIR Designee Authority and Responsibilities
300. General. AIR designees, within limits and under the supervision of the advisor, may be authorized to perform examinations, inspections, and witness tests in the manufacturing and engineering areas.
a. Designees must be familiar with and have ready access to all appropriate FAA publications and documents. Designees may not perform any functions until the required documents are obtained. Material may be downloaded from the FAA Designee and Delegation website at http://www.faa.gov.
b. Designees ARE NOT authorized to perform evaluations, surveillance, or investigation of quality control systems data, procedures, methods, or service difficulty reports, on behalf of the FAA.
c. Designees ARE NOT authorized to approve departures from specific policy and guidance, new/unproven technologies, equivalent level of safety findings, special conditions, or exemptions. These are inherently governmental functions and cannot be delegated to a designee.
d. Designees ARE NOT authorized to issue U.S. airworthiness certificates or special flight permits on non-U.S.-registered aircraft.
e. The FAA inspector or engineer WILL NOT authorize any privileges not covered in part 183. Designees will perform only authorized functions within the limits of designated authority.
f. Designees, while acting pursuant to their appointment, are representatives of the Administrator for specified functions and ARE NOT considered employees of the FAA. Designees are authorized to use their titles (for example, DMIR or DAR) only when performing those functions specifically delegated by the FAA managing office.
g. Designees, upon appointment and renewal, must acknowledge that designation is a privilege, not a right, and understand the designation may be terminated at any time for any reason at the discretion of the Administrator.
h. Designees are responsible for obtaining and maintaining all guidance material (including FAA forms) necessary to perform their authorized functions. All designee guidance material is available on the designee section of the FAA.gov website. This website is intended to be the primary source of electronic designee guidance material. AFS and AIR maintain this website. If designees are unable to obtain guidance material through the Internet, they may contact their managing/appointing offices for assistance.
301. Manufacturing Designee Authority.
a. Manufacturing DMIRs are responsible for performing authorized functions in accordance with the pertinent regulations, FAA directives, and any specific instructions conveyed by their managing office(s). A DMIR will—
(1) Be authorized to assume responsibility for performing authorized functions concerning products and/or articles produced and controlled by their employer’s production approval,
(2) Not issue U.S. airworthiness certificates or special flight permits for non-U.S.-registered aircraft,
(3) Perform functions only within the limits of their authority, and
(4) Provide information related to their accomplishments in accordance with the schedule established by their managing office.
b. Manufacturing DARs are responsible for performing authorized functions in accordance with the pertinent regulations, FAA directives, and any specific instructions conveyed by their managing office(s). A DAR will—
(1) Perform only authorized functions within the limits of their authority.
(2) Contact their managing office for authorization BEFORE accepting any certification or inspection activity requested by an applicant. Obtain any special directions or instructions deemed necessary by the advisor requesting the inspection activity.
(3) Provide information relating to their accomplishments in accordance with the schedule established by their managing office.
(4) Ensure that FAA forms, certificates, and other official documents are properly safeguarded. Under no circumstance may any certificate be in the possession of an applicant until the DAR has completed and signed the certificate. All airworthiness certificates or approvals and related documents (for example, application for airworthiness certificates, limitations cited and attached to FAA Form 8130-7, Special Airworthiness Certificate, and FAA Form 8100-2, Standard Airworthiness Certificate) will indicate the DAR’s printed or typed name, signature, and designation number.
(5) Not perform any mechanical, maintenance, or inspection function on behalf of an applicant (for example, owner, agent, repair station, or production approval holder (PAH)) on products or articles for which an airworthiness certificate or approval is sought. This would not preclude the DARs from performing maintenance, mechanical functions, or inspections in a non-DAR capacity when NOT involved in the airworthiness certification/approval actions under their DAR authority.
(6) Ensure a product meets the FAA-approved type design data, is in a condition for safe operation, and complies with all applicable regulations (for example, marking requirements, registration, and special importing requirements) before issuing an airworthiness certificate. The DARs will seek guidance from their managing office when problems arise that they cannot resolve.
(7) Ensure FAA Form 8100-1, Conformity Inspection Record, is used in accordance with the instructions provided in FAA Order 8130.2, Airworthiness Certification of Aircraft and Related Products.
(8) Submit applicable original or duplicate documents within 7 days of completion to the managing office for review.
(9) Review applications for completeness and ensure the various airworthiness certificates or approvals have certification statements signed by an applicant or authorized agent. When appropriate, the DAR also must obtain a completed FAA Form 8130-9, Statement of Conformity, from an applicant before performing any inspections.
(10) Ensure special flight permits issued for overweight operations are in accordance with the latest revisions of all applicable guidance material (for example, FAA Order 8130.2). The DAR will contact the managing office to obtain any special directions or instructions BEFORE issuing a special flight permit for overweight operations.
302. Cross-Utilization of DARs. Manufacturing designees are primarily responsible for original airworthiness certification, and maintenance designees are primarily responsible for recurrent airworthiness certification. However, there are some manufacturing function codes that authorize recurrent certification activity and some maintenance function codes that authorize original certification activity. When considering an appointment that includes function codes with recurrent authorization, the manufacturing managing office should coordinate with the geographically responsible flight standards district office (FSDO) on the intent to delegate recurrent functions. Include documentation verifying this coordination in the evaluation package for the applicant/designee.
a. When delegating a recurrent certification activity to a designee whose certificate of authority (COA) contains a function code that includes recurrent authority, the manufacturing managing office should notify the geographically responsible FSDO of the activity. This coordination can be in person, telephonic, electronic (for example, email), or by a paper document. Document the coordination by entering a comment in the general comments section of the designee’s DIN record and scan and attach a copy of any appropriate documentation.
Note: Under no circumstances will a manufacturing managing office authorize a designee to perform any recurrent certification activity not specifically included in the manufacturing function codes contained in this FAA order and granted to that designee on the electronic COA (eCOA).
303. Manufacturing Designees - International Operating Procedures.
a. Operating Outside Geographic Boundaries. It is the FAA’s intention that all manufacturing designees perform their authorized functions within the managing office’s geographic boundaries. However, a managing office may authorize a manufacturing designee to perform authorized functions outside its geographic boundaries on a case-by-case basis when the FAA’s ability to adequately monitor and supervise the designee is maintained. Chapter 9 contains detailed instructions on management of designees operating outside their geographic boundaries.
b. Feedback to Foreign Authorities. On some occasions, manufacturing designees may conduct activities in foreign facilities that hold an approval from their local Civil Aviation Authority (CAA). If problems are encountered during a U.S. project, the designee must provide the details to the managing office. The managing office will determine if any system issues or major problems should be forwarded to the applicable CAA for its consideration. For example, if the outcome of a test fails or articles are nonconforming, it may be evidence of a system breakdown or a compliance problem at that facility.
304. Engineering Designee - DER Authority. The DER may approve engineering technical data within the limits of the authority assigned by means of FAA Form 8110-3, Statement of Compliance with the Code of Federal Regulations, and, when authorized by the ACO, may witness FAA compliance tests and perform compliance inspections. DERs will follow the procedures of FAA Order 8110.4, Type Certification Process. The specific roles, authorized areas, and responsibilities of the DER will be established by agreement between the ACO and the DER.
Note: On a case-by-case basis, with proper coordination with the MIDO and assurance of technical ability, the ACO and MIDO may authorize a DAR to witness a compliance test.
305. Engineering Designee Appointments - Company/Consultant Categories.
a. Company DER. An individual may be appointed to act as a company DER for the individual’s employer and may approve, or recommend approval to the FAA of, only technical data for the company. Company DERs may perform their FAA functions at different administrative levels, as agreed upon between the FAA and the company. In some cases, a DER personally may evaluate and approve technical data. In other cases, a DER may ensure, through the company management system, the proper evaluation of technical data by other persons; then the DER will approve that data by certifying that the data comply with the applicable regulations. If a company DER is assigned to work in a consortium, business arrangement (such as using other companies’ DERs), partnership, licensing agreement, etc., the company should request in writing to expand the existing delegation. If the expansion of the DER company delegation involves the geographic area of responsibility of two different ACOs, the two ACOs will determine which office will manage the expanded delegation.
b. Consultant DER. An individual may be appointed to act as an independent (self-employed) consultant DER to approve, or recommend approval of, technical data to the FAA for a client.
c. Dual Appointments. An individual may be appointed to act as both a company DER and a consultant DER. In such a case, two separate (dual) appointments will be made and separate certificates of delegation issued.
(1) The ACO will advise the DER that the employer should be informed of the dual appointment. In the case of dual appointments, the consultant DER delegation may be authorized for areas different from the company DER delegation, depending on the applicant’s experience and the limitations the ACO may place on the DER.
(2) Each of these appointments should be managed by the same appointing ACO. If the company DER delegation and the consulting DER delegation would be in the geographic area of responsibility of two different ACOs, the two ACOs will determine which office will manage the dual delegation.
d. Multiple Specialty Appointments. A qualified person may be appointed to act as more than one type of DER listed in part 183. The appointee must be qualified to determine compliance with 14 CFR in authorized areas and delegated functions assigned from those listed in appendix A, figure A-3 of this order (see DER Application Evaluation — General Technical Criteria).
306. Engineering Designations.
a. Structural DERs may approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Engineering reports.
(2) Drawings.
(3) Test witnessing and reports (with prior FAA approval).
(4) Material and process specifications used in structural applications.
(5) Other data relating to structural considerations.
b. Powerplant DERs may approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Engineering reports.
(2) Drawings.
(3) Test witnessing and reports (with prior FAA approval).
(4) Other data relating to powerplant installations, including all systems and equipment necessary for the proper operation of the powerplant.
c. Systems and equipment DERs may approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Engineering reports.
(2) Drawings.
(3) Test witnessing and reports (with prior FAA approval).
(4) Other data relating to aircraft systems and equipment design not covered by the structural or powerplant DER.
d. Radio DERs may approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Engineering reports.
(2) Drawings.
(3) Other data relating to the design and operating characteristics of radio equipment being manufactured and/or modified.
e. Engine DERs may approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Engineering reports.
(2) Drawings.
(3) Test witnessing and reports (with prior FAA approval).
(4) Other data relating to durability, materials, and processes employed in engine design, operation, and maintenance.
f. Propeller DERs may approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Engineering reports.
(2) Drawings.
(3) Test witnessing and reports (with prior FAA approval).
(4) Other data relating to propeller blade and hub design, pitch control, propeller governing, and maintenance, provided these items comply with the pertinent regulation(s).
g. Flight analyst DERs may approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Aircraft performance flight-test data.
(2) Aircraft quantitative operating data.
(3) Flight characteristic data.
h. FTP DERs may conduct and approve, within the limits of their appointment, flight tests of new or modified aircraft.
i. Acoustical DERs, when delegated on a case-by-case basis, may witness and approve, within the limits of their appointment, the following items that comply with pertinent regulation(s):
(1) Noise certification tests conducted in accordance with an FAA-approved test plan.
(2) Noise data.
(3) Noise analyses.
(4) Test results that were measured and evaluated as prescribed in 14 CFR part 36, Noise Standards: Aircraft Type and Airworthiness Certification, subparts A through J, or by an equivalent procedure previously approved by the FAA Office of Environment and Energy (AEE-1).
307. Engineering Designees - Special Designations. A DER may be appointed to approve technical data not specifically listed in the charts of appendix A, figure A-3 of this order. Each chart has an authorized area of “special,” with delegated functions to cover this contingency. When we authorize a special delegation, we list the “special” authorized area and specifically define the function. A DER must have significant experience in the appropriate area to be given a special delegation. The following “special” delegations may be authorized:
Note: Use of “special delegations” other than those defined in this order should be coordinated with the Engineering Procedures Office (AIR-110).
a. Administrative/Management DERs. A qualified person may be appointed as an administrative coordinator or manager of an applicant’s certification program. We assign this person the authorized designation of administrative DER or management DER. These special designations are not associated with a particular chart for DER authority in appendix A to this order. It must be recognized that the management DER and administrative DER are not actually DER types with authority prescribed by part 183, rather special authorizations introduced by FAA policy. These authorizations were established to recognize certain individual’s capability to provide assistance to the ACO in administrative and project management aspects of certification. In performing this role, an administrative/management DER does not use Form 8110-3.
(1) Administrative DER. The administrative DER, usually a company DER, acts as a focal point for FAA coordination activity, including organizing technical DER activity, correspondence, schedules, meetings, conformity inspections, and FAA participation in official tests. Administrative DERs perform administrative tasks only and therefore are not required to be appointed under one of the delegations listed in § 183.29.
(2) Management DER. The management DER, usually a consultant DER, performs FAA certification project management duties for the FAA, acting like an FAA project manager. They organize the applicant’s certification program, directing, overseeing, and managing the tasks of technical assessments and findings of compliance. The management DER ensures all technical data required to show compliance is reviewed and approved by the appropriate technical DER, except those items reserved by the FAA for approval. To establish his capability as an FAA project manager, we must first appoint a management DER under one of the delegations listed in § 183.29.
b. Major Repairs and Alterations. A DER requires specific authorization to examine and approve data for alterations and/or major repairs. We may assign a DER the authorized area of “special-major repairs” and/or “special-major alterations,” which will be related to the DER’s basic delegations. A sample letter authorizing data approval for repairs and alterations is shown in appendix E, figure E-2 of this order. A DER only needs this delegation if his Form 8110-3 will be referenced as the approved data for a specific major repair or major alteration. The three specific authorizations are as follows:
(1) Special-major repairs.
(2) Special-major alterations.
(3) Special-major repairs and major alterations.
Note 1: DERs with specific delegation for vintage aircraft are limited to examination of data and findings of compliance within their specialty in support of field approvals under FAA Order 8900.1.
Note 2: We may give special-major repair DERs specific authority to approve data for repair specifications and/or approve repair specifications (RS-DER).
Note 3: Service documents and overhaul manuals produced by the original design/PAH are not considered major repair or major alteration data that require this specific authorization.
c. Special Delegation for Repairs and/or Alterations for Vintage Airplanes and Engines
(1) Special Delegation Authority. A designated engineering representative (DER) may be appointed with a special delegation for major repairs and/or major alterations for vintage airplanes and/or engines. This authority allows a DER to approve data for only the types of repairs and/or alterations to vintage airplanes and/or engines that would be eligible for Federal Aviation Administration (FAA) field approvals under FAA Order 8900.1. A DER with
this special delegation may have their authority defined by multiple technical specialty areas with specific limitations noted. The specific authorizations are:
(a) Vintage airplane (or engine) major repairs,
(b) Vintage airplane (or engine) major alterations, and
(c) Vintage airplane (or engine) major repairs and major alterations.
Note: The intent is to allow individuals who don’t meet the conventional DER appointment criteria to become DERs with limited approval authority in multiple technical specialties for repairs and/or alterations of specific makes of vintage airplanes and/or engines. This will facilitate complete approvals by a single DER when practical.
(2) Vintage Airplanes and Engines. For the purpose of this authority, vintage airplanes are those airplanes certificated under Civil Air Regulations (CAR) 3, or earlier certification basis, and manufactured before 1973 that meet all of the following parameters:
(a) Single-engine,
(b) Maximum five-place,
(c) Maximum 7,000 pounds gross takeoff weight,
(d) Nonpressurized, and
(e) Noncomposite metallic or wood primary structure.
Note: Vintage engines are all radial engines, and all other piston engines manufactured before 1973.
(3) Evaluation Panel. The evaluation panel for applicants seeking this special delegation must consist of at least three individuals: one representative from the Small Airplane Directorate and two representatives from the requested technical disciplines. For applicants seeking authority for engines, the evaluation panel will also include a member from the Engine and Propeller Directorate. A representative from the FAA AFS with knowledge of the applicant’s activity also is highly recommended.
d. Repair Specification DER (RS-DER). To be authorized to manage repair specification approval projects, the DER must have appropriate experience and be qualified to manage repair specification data approvals. DERs granted the specific authority to manage and approve technical data in repair specifications are called RS-DERs. An “RS-DER” is a shortened name for a DER with the special delegation to approve serial number-specific major repair data, non-serial number-specific major repair data, and manage repair specification approvals. Once the RS-DER is satisfied that the repair specification meets all the requirements,
then, to indicate they have completed their review of the repair specification, they must sign the cover page with their name and DER number.
(1) An RS-DER is responsible for managing the repair specification project and approving some, if not all, of the technical data associated with the repair specification. The technical data is approved via Form 8110-3. The RS DER may rely on other DER-approved data, provided the DERs have the appropriate delegation of multiple repairs.
(2) DERs may be authorized to perform two specific functions in the repair specification approval process:
(a) To manage the repair specification project and approve the technical data in the repair specification, and/or
(b) To approve data in support of multiple-use, non DAH, non-serial number specific repairs.
(3) A DER must be authorized for at least one of the two functions specified in paragraphs (2)(a) or (2)(b) above, to support repair specification approvals.
Note 1: Existing DERs who are already authorized for multiple-use repairs can approve data to support repair specification approvals without any additional specific authorization.
Note 2: Existing DERs who are already authorized for serial number specific repairs may continue to make those findings.
e. Parts Manufacturer Approval (PMA) Identicality. A DER requires specific authorization to examine and make findings of identicality to obtain a PMA. This is appropriate only where a DER has access to the original design approval holder’s data, allowing them to make a direct comparison of design data.
Note: We authorize test and computation findings within the scope of the DER’s basic delegation.
f. Alternative Methods of Compliance (AMOC) with Airworthiness Directives (AD). We may give a design approval holder’s company structural DER the authority to approve AMOCs for specific structural ADs where the intent of the AD was to restore the airplane to its type certification basis or other known, defined, and published standards.
308. Engineering Designees - Special Authorizations. The level of data approval and/or delegation we grant a DER may vary from project to project depending on the complexity of the project. A project ACO manager or manager’s representative may issue a special authorization, in writing, permitting a DER to approve data normally reserved to us (that is, witness tests, approve test plans) within the DER’s scope of authorization. The special authorization must be specific in its delegation and time-limited, and is valid only at the ACO that issued the authorization. Verbal authorization from the ACO is permitted in some cases, such as witnessing tests, if the DER documents it on the subsequent Form 8110-3 or other acceptable method. See
FAA Order 8110.37, Designated Engineering Representative (DER) Guidance Handbook, appendix A, Limitations on DER Functions, for activities that may be permitted by special authorization letter.
309. Engineering Designees - Delegated Functions/Authorized Areas/Limitations/ Specific Functions.
a. Delegated Functions. A delegated function applies to the technical areas involved in determining compliance with applicable airworthiness regulations.
b. Authorized Areas. An authorized area applies to the specific portion or system of an aircraft or the type of engine or propeller or specialized area to which a delegated function is applicable applies.
c. Limitations. A DER may be appointed for, or limited to, specific types of work. For example, a systems and equipment DER could be limited to handling approval of alterations to specific types of systems (for example, hydraulic and pressurization on only one airplane model), or an FTP DER could be limited to conducting flight tests on fixed-wing aircraft of a specified maximum gross weight. Caution should be exercised in making delegations so narrowly limited that they become burdensome to the FAA.
Note: The FAA retains authority and responsibility for examining and approving certain items. This limits the data that the DER can approve. FAA Order 8110.37, appendix A, lists those areas that would more than likely be reserved for FAA approval but that could be delegated to a DER.
d. Specific Functions. Within a delegated function and authorized area, a DER can be authorized specific function requirements by his managing office. This is not an expansion of a DERs authority, rather a specific direction to the DER’s role within his current delegated authorization. Examples of specific functions are as follows:
(1) Electrical DER-specific functions related to electrical wiring interconnection systems (EWIS), and
(2) Structural DER-specific functions related to the aging airplane safety rule (AASR) to support 14 CFR part 26 requirements.
Note: See FAA Memorandum, Authorization and Delegation of Functions Related to the Aging Airplane Safety Rule (AASR), for areas of delegated authority available for authorization/delegation.
e. DER Authorization. The delegated functions and authorized areas for each DER will be established from the appendix A, figure A-3 charts of this order, before the applicant’s original appointment, and again during review at the DER’s authority change or renewal date. These will be listed on the COA, the letter of appointment, or any letter(s) of renewal or authority for expansion or deletion. Any other limitations appropriate to the appointment, such as certain CAR or other regulation(s), are also listed on the form. “Recommend approval” may be used only for those delegated functions authorized on the COA. The scope of the
designation, and any limitation considered necessary at the time of appointment, will be clearly indicated on the COA or other related documentation.
Note: The delegation of a specific portion of 14 CFR also includes the delegation for predecessor and other applicable regulations unless specifically excluded. Approval for predecessor regulations typically would be limited to 14 CFR or CAR airworthiness requirements.
310. Engineering Designees - International Operating Procedures.
a. Finding Compliance to Foreign Regulations.
(1) Approval Basis. The ACO may authorize a DER to make compliance findings to specific foreign regulations delegated to the FAA by a foreign CAA. This can be done in accordance with Implementation Procedures for Airworthiness (IPA) under a Bilateral Aviation Safety Agreement (BASA) or some other written FAA-approved arrangement with that country (after consultation with the International Policy Office staff, AIR-40). If the FAA accepts the delegation of a compliance finding from a bilateral or Joint Aviation Authorities (JAA) member country or from the JAA under the BASA IPA, that finding could be made either directly by the FAA or by an appropriately qualified designee. The decision to delegate the compliance finding, as well as the decision to provide this special authorization to a designee, is made by the FAA only, depending on availability of resources. A DER who is granted such approval authority must have demonstrated knowledge of the foreign regulations and their application to the appointing ACO. This typically will be evidenced by participation on previous validation programs with the foreign CAA and the FAA.
Note: For paragraph 310a(1) above, the JAA/European Aviation Safety Agency (EASA) may be substituted as a foreign CAA.
(2) Form 8110-3 Distribution. The DER will provide the original Form 8110-3 to the project ACO. The DER must also send a copy of the form to the appointing ACO, if different from the project ACO. The substantiating data must be provided to the project ACO if the Recommend Approval block is checked. The substantiating data must be made available to the project ACO if the Approval block is checked. The project ACO will transmit FAA final approval for the compliance finding to the foreign CAA. In that final approval, the FAA confirms that compliance has been demonstrated and findings of compliance have been made.
(3) Completion of Form 8110-3. A DER with this specific authorization is permitted to approve data only to the additional technical requirements for the affected CAA as specified in the agreed certification basis or as written on the type certificate (TC) data sheet of the affected product. A DER may approve this data only for the aircraft models for which the DER is authorized. When approving data to harmonized requirements, the DER should complete Form 8110-3 to identify the applicable portion(s) of 14 CFR rather than the foreign regulations.
b. FAA-Accepted Foreign Requirements. A finding of compliance also may be made to requirements that have been adopted or accepted by the FAA when used in certifying certain small aircraft. Form 8110-3 is used to approve or recommend approval with U.S. requirements or foreign CAA regulations as authorized by the ACO.
c. Compliance Findings Outside the United States. A DER may be authorized to find compliance to 14 CFR on behalf of the FAA in a country other than the United States under the following conditions and limitations:
(1) Project ACO. The project ACO must coordinate, as applicable, with the certificate managing ACO for significant projects as noted in paragraph 2-4c of FAA Order 8110.4.
(2) DER Access. The DER and the FAA should be aware that some countries do not allow FAA designees to operate in their jurisdiction, or prefer to be given the opportunity to participate on major FAA projects themselves, in lieu of a DER conducting the requested tasks.
(3) U.S.-Certificated and Foreign-Registered Aircraft. The DER may engage only in activities pursuant to an FAA TC or FAA approval, or by direction of the project ACO.
Note: DERs are never authorized to work for another CAA in their FAA DER capacity.
(a) U.S.-Registered Aircraft. Before a project ACO authorizes a DER to perform any authorized function(s) outside the United States, the project ACO must review any bilateral agreements and comply with any requirements for prior notification with the CAA. If required, the notification will outline the proposed visit (anticipated activities, length of stay, etc.).
Note: The FAA is responsible for contacting the CAA if there is no bilateral agreement or if a bilateral agreement requires prior notification. For a list of bilateral agreements, go to the AIR Products and Services website at http://www.faa.gov.
(b) Foreign-Registered Aircraft. If an aircraft is on a foreign registry, the project ACO must have requested and received written permission/authority from the state of registry before conducting any activity with the aircraft. The applicant must submit the letter, or the ACO must obtain the letter from the airworthiness authority of the state of registry with the supplemental type certificate (STC) application, unless prior written permission exists. The foreign CAA letter should state that the CAA will accept the modification itself and that the CAA has no objections to the use of FAA designees to approve this work (for example, FAA DARs making findings of conformity, or DERs making findings of compliance for modifications/alterations on the aircraft registered in their country).
Note: Agreement from the CAA of the state of registry is required by the International Civil Aviation Organization as evidence of the CAA’s awareness of its continued airworthiness and reporting obligations for the modification.
(4) Conformity Inspections. A DAR/DMIR with proper FAA authorization may conduct and verify conformity inspections required for the project. The DER should meet with the project ACO/MIDO as an initial step in the project to establish that the proposed DER and DAR/DMIR have the knowledge of the aircraft type design necessary to make findings of data compliance and conformity. For additional guidance concerning conformity inspections, see FAA Order 8110.4.
(5) Reporting Activities. During the DER’s stay outside the United States, the project ACO may require the DER to report activities periodically.
(6) FAA-Approved Repair Stations. DERs working with FAA-approved repair stations in foreign countries must give prior notification, in writing, to the FAA Flight Standards International Field Office (IFO) having cognizance over the particular repair station involved. For identification and location of IFOs, DERs should consult the ACO or a regional FSDO.
(7) Feedback to Foreign Authorities. On some occasions, DERs may conduct certification activities in facilities that hold an approval from their local CAA. Problems may be encountered during the U.S. project certification activities, such as test failures due to nonconforming test articles or inattention to test plan details. Such experience might be evidence of a system breakdown or major problem at the facility. If such problems are encountered, the DER must advise the project ACO by providing the details of any problems experienced. The ACO will then determine if any systemic issues or major problems should be forwarded to the applicable CAA for its consideration.
Chapter 4. AIR Application Process
400. General. This chapter describes the process by which a qualified private person may apply for appointment as an AIR designee. The initial contact may be a verbal request for information or a request for an application package. Initial contacts are opportunities for the FAA to share with the prospective applicant the responsibilities, expectations, and qualification requirements of designees. By providing this information, the FAA may find that some individuals elect not to submit an application based on their inability to satisfy the high qualification requirements for appointment. This initial contact stating the high FAA expectations for designee appointment may eliminate resource hours being expended on application packages that would be rejected.
a. When an individual elects to pursue appointment, the local FAA managing office will forward all requests to the person who will serve as the DPC. Any false statements made by the applicant in the application package are grounds for denial of appointment. (For FAA locations, visit http://www.faa.gov.)
b. The DPC will direct the applicant to the designee page at http://www.faa.gov. The applicant can download the appropriate application forms. When the prospective applicant submits the completed application package, the DPC will initiate the formal review process and coordinate all subsequent FAA actions.
Note: There may be local working agreements between the appointing ACO/manufacturing inspection office (MIO)/MIDO/CMO and specific companies that provide guidelines for identifying individuals as prospective designees; however, all prospective applicants must meet all qualification criteria before appointment.
401. Application Package. The applicant must submit the following:
a. Cover Letter. A DAR applicant or consultant DER applicant must submit a cover letter requesting appointment. An applicant for a DMIR or company DER must submit a letter from the applicant’s employer requesting an appointment and identifying any special recommendations or limitations considered appropriate with respect to the desired authority. The cover letter for all DER applications must include the applicant’s plans for activity as a DER. Companies should apply for the appointment of only as many designees as they deem appropriate for the services to be rendered.
b. Form 8110-14. The applicant must submit a completed Form 8110-14 with an original signature (see appendix A, figure A-1 of this order). For a company designee, the employer must complete and sign item 13. Include the company’s address and telephone number on the form. Item 4, Social Security number, and item 5, date of birth, are no longer required.
c. Evaluation Forms. The applicant must complete and submit applicable portions of the evaluation forms (see appendix A, figures 3 and 4 of this order) that are based on the specific designation being sought. The applicant also must submit supplemental documentation that substantiates experience in each of the four evaluation criteria (that is, regulatory, technical, interface, and standardization). The applicant must return the evaluation forms and supplemental
information with the rest of the completed application package. When returned, the evaluation forms identify the delegations sought and provide a means for the FAA to record the evaluation and decision regarding the application. The evaluation of the applicant’s information will determine if an applicant may be appointed, identified as a candidate, or denied appointment. Appointment is made when an applicant meets the criteria, has had direct FAA interaction (depending on the designation being sought), and provides verifiable documentation, and the FAA has the need and ability to manage the designation. Failure to meet the applicable criteria will result in a denial. The applicant’s qualifications will be evaluated against the regulatory, technical, interface, and standardization appointment criteria described below.
402. Regulatory Appointment Criteria.
a. DER.
(1) The applicant is cognizant of regulatory requirements and problems related to civil aircraft approvals and has direct experience requiring expertise in the general certification process.
(2) The applicant has a thorough working knowledge of the specific 14 CFR parts and predecessor regulations for which the designation is requested.
b. DMIR/DAR The applicant is knowledgeable of the pertinent regulations, directives, and related guidance material.
403. Technical Appointment Criteria — General.
a. DER.
(1) Each applicant has been in a responsible position in connection with the type of work for which the designation is being sought, and is cognizant of related technical requirements and problems related to civil aircraft approval, or has otherwise demonstrated suitability for this designation; see appendix A, figure A-3 of this order.
(2) The applicant has the basic engineering knowledge appropriate to the designation being sought, as demonstrated by 8 years of progressively responsible engineering experience for which an engineering degree may be substituted for up to 4 years of maximum credit. An applicant who has not earned an engineering degree may substitute 40 credit hours of successfully completed course work in engineering or related curriculum for 1 year of experience, up to 4 years of maximum credit.
(3) Three verifiable technical references are required to substantiate that the applicant possesses the required technical expertise for the areas of delegation being sought. These references may be the same persons used for character references.
(4) For company DERs, the application must include a statement from the company attesting to the applicant’s technical competency.
Note: The applicant’s documented technical expertise will be evaluated against the Delegated Functions/Authorized Area Charts and will be used to determine the scope of appointment.
(5) For DER applicants who wish to be delegated authority to make compliance findings to foreign CAA’s regulations, knowledge in the application and interpretation of the specific foreign regulations must be demonstrated.
b. DMIR/DAR.
(1) Each applicant must possess current technical knowledge and meet experience requirements in connection with the production or inspection of products and/or articles OF THE SAME TYPE AND COMPLEXITY for the functions sought. For specialized technical appointment criteria, refer to the DMIR/DAR application in appendix A, figure A-4 and at http://www.faa.gov.
(2) Three verifiable technical references are required to substantiate that the applicant possesses the required technical expertise for the designation sought. These references may be the same persons used for character references. DMIR applicants must include a letter of recommendation from the company attesting to the applicant’s technical competency; this may be considered one of the three required technical references.
(3) A DMIR must be employed by a PAH or a PAH’s approved supplier and be familiar with the facilities, procedures, manufacturing practices, and inspection techniques in connection with type certification, original airworthiness certification, export certification, and parts approval and associated data, as appropriate for the functions sought.
404. Technical Appointment Criteria — Specialized — DER.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
FTP DER designation 1. Hold a commercial pilot certificate with an instrument rating, and be qualified in aircraft of the same category and class and similar in design to that in which the applicant will be conducting tests.
2. Have logged a minimum of 2,000 pilot-in-command flying hours (1,000 hours for helicopters) of which at least 100 hours have been logged within the past 12 months.
3. Have logged a minimum of 100 hours of appropriate experimental flight testing experience in the same certification category and in a similar type of aircraft for which the DER appointment is requested.
Note: The requirements of paragraphs 2 and 3 above are initial requirements, not annual requirements.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
DER with a delegation 1. A thorough working knowledge and understanding of RTCA of software approval Document DO-178 (as amended), Software Considerations in Airborne Systems and Equipment Certification.
2. An understanding of and experience with DO-178 software life cycle data required for certification (for example, Plan for Software Aspects of Certification, Software Configuration Index, Software Accomplishment Summary, Software Quality Assurance Plan, Software Development Standards, Software Verification Plan, and Software Tool Qualification Plan). The applicant also should demonstrate the ability to assess the quality of all software life cycle data and the development team’s adherence to approved plans and standards.
3. Familiarity with the systems safety assessment process, specifically, those portions that establish the software criticality level.
4. A demonstrated knowledge of the rationale for, and the significance of, each stage in the software development process, as well as its supporting standards, procedures, and documentation. The applicant should be able to identify the critical aspects and contents of each of the documents in DO-178.
5. Experience gained from participation in some technically responsible capacity over a complete software development program life cycle. This qualification may be satisfied by an aggregate of different software development programs.
6. Experience interacting with all phases of software development and testing processes addressed by DO-178, including use of the associated configuration and quality control procedures. This experience should include significant responsible involvement in several of those phases. When assessing an applicant’s capabilities for making a knowledgeable finding of compliance, experience obtained in the requirements development or testing phases may, for example, be weighted more heavily than that obtained in the detail design or coding phases.
7. Fluency in at least one high-level and one assembly-level programming language and familiarity with typical support software used in a software development process. Familiarity with typical software tools available to facilitate the development, documentation, and consistency-checking processes is highly desirable.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
8. Demonstrated knowledge of the sources of software anomalies, the relative merits of the types of testing procedures available to protect against them, and the characteristics of a thorough test program.
9. Familiarity with the aspects of computing peculiar to real-time avionics systems, such as the use of interrupts, multitasking, and software reentrancy. This should include an understanding of the types of analysis and testing necessary to ensure the integrity of these mechanisms.
10. An understanding of the techniques that may be employed to reduce software criticality levels, such as system architecture, dissimilar software, and partitioning. This should include the ability to assess the adequacy of a proposed technique relative to the system integrity required.
11. Knowledge of hardware characteristics such as input/output schemes, memory organization and multiport access, communication-bus protocols, and processor architecture, all of which have an impact on the software interface and the potential for the creation of anomalies.
12. Demonstrated use of DO-178 objective tables and assessing a project’s compliance to those objectives. This includes familiarity with the FAA’s software review approach as explained in FAA policy and the job aid titled “Conducting Software Reviews Prior to Certification.”
13. Experience with software verification process activities, including reviews, analyses, and testing.
14. Experience with software structural coverage analysis, including determination of modified condition/decision, condition coverage (level A only), decision coverage (levels A and B), statement coverage (levels A, B, and C), and data coupling and control coupling analyses (levels A, B, and C), as appropriate for the software level being approved.
15. Familiarity with post-certification software processes (for example, manufacturing quality control, factory configuration control, acceptance test procedures, factory installation and test equipment, production equipment control, and field-loadable software control).
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
16. Familiarity with software modification processes, including change impact analyses, upgrading previously developed software, and regression analyses and testing.
17. Familiarity with current FAA software policy (for example, policy on field-loadable software, software changes in legacy systems, user-modifiable software, software tool qualification, software review process, and previously developed software).
18. A minimum level of successful experience before the DER is allowed to approve certain software. The experience of the DER to be considered in relation to software level is as follows:
a. Level A Software. A DER should have at least 1 year of successful experience reviewing level A software data submittals before being designated to approve any level A data.
b. Level B Software. A DER should have at least 1 year of successful experience reviewing either level A or level B software data submittals before being designated to approve any level B data.
c. Level C Software. A DER should have at least 1 year of successful experience reviewing either level A, level B, or level C software data submittals before being designated to approve any level C data.
d. Level D Software. A DER may be designated to approve level D data if the qualification criteria for appointment as a DER with software approval have been met.
Note 1: The appointing ACO will determine what limitations, if any, will be placed on the DER’s software approval level. These limitations may be expressed in the terms used in DO 178 and defined on related documentation.
Note 2: Normally, the Plan for Software Aspects of Certification and Software Accomplishment Summary should be reserved for approval by the ACO.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
Structural DER with a delegated function of damage tolerance evaluation
1. A degree in one of the following:
a. Engineering mechanics.
b. Aerospace/Aeronautical engineering.
c. Mechanical engineering.
d. Civil engineering.
Note: In addition to one of the above, a course in fracture mechanics is desirable, if not taken during the degree program.
2. The equivalent of 2 full years of experience in damage tolerance analysis. The experience must be within the last 10 years before appointment.
Structural DER with 1. A degree in one of the following: delegated functions of fatigue analysis a. Engineering mechanics.
b. Aerospace/Aeronautical engineering.
c. Mechanical engineering.
d. Civil engineering.
Note: In addition to one of the above, a course in fatigue analysis is desirable, if not taken during the degree program.
2. The equivalent of 2 full years of experience in fatigue analysis. The experience must be within the last 10 years before appointment.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
Administrative DER Significant experience in direct contact with the FAA in which the (who is usually a applicant has been actively engaged in processing FAA approvals. company DER) This experience must enable the FAA to determine that the applicant is cognizant of the overall certification process and the administrative problems encountered in obtaining approvals. When the ACO has documented that an equivalent finding has been made to demonstrate that the applicant meets the intent of paragraph 403 of this chapter (Technical Appointment Criteria–General), and paragraph 405 of this chapter (Interface Appointment Criteria), the ACO manager may, at their discretion, appoint an applicant who does not meet all of the other requirements of table 4-1.
Management DER Significant experience in direct contact with the FAA in which the (who is usually a applicant has been actively engaged in processing FAA approvals consultant DER) and has demonstrated technical DER knowledge over a variety of FAA projects. This experience must enable the FAA to determine that the applicant is cognizant of the overall certification process, has experience working with other technical disciplines, and is cognizant of the management problems encountered in obtaining approvals. Management DERs must first be appointed to one of the delegations listed in appendix A to this order.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
DER with a delegation of vintage aircraft approval
1. Sufficient experience in direct contact with the FAA in which the applicant has been actively engaged in processing FAA approvals and has demonstrated DER knowledge over a variety of vintage aircraft projects. This experience must enable the FAA to determine that the applicant is cognizant of the overall certification process, has experience working with other technical disciplines, and is cognizant of the management problems encountered in obtaining vintage aircraft STC and field approvals.
2. In lieu of general requirements—
a. Each applicant may alternatively have been in a responsible position in connection with the type of work for which the designation is being sought, and be cognizant of the related technical requirement and problems related to civil vintage aircraft alterations via the STC and field approval process.
b. Each applicant may have the basic engineering knowledge appropriate to the designations being sought, as demonstrated by 8 years of progressively responsible work performing alterations via STC or field approvals as a Function Code 50 DAR, as an Airframe and Powerplant Mechanic (A&P) with an Inspection Authorization (IA) or with an FAA Repairman Certificate as appropriate for his particular delegation. An applicant who has Function Code DAR experience may substitute 1.5 years for every 1 year of experience in the certificate process toward the total of 8 years.
c. The applicant may have the basic engineering knowledge appropriate to the designations being sought as well as knowledge of the applicable certification requirements. The applicant must have at least 12 years of progressively responsible experience performing repairs and alterations of the general type of airplanes for which appointment is sought. As an example, if an applicant has had 12 years modifying Piper tube and fabric airplanes doing structural modifications, they would be delegated vintage aircraft approval for Piper tube and fabric airplanes in the structures discipline, as well as aircraft of similar constructions such as Aeronca Champs, Taylorcraft and other similar aircraft. DERs delegated vintage aircraft approval may operate outside their designated area of responsibility when given authorization from their DER advisor in the cognizant ACO.
3. Three verifiable technical references are required to substantiate the applicant possesses the required technical expertise for the areas of
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
delegation being sought. These references may be the same people/persons used for character references.
4. For company (type club or non-profit) DERs delegated vintage aircraft approval, the application must include a statement from the type club attesting to the applicant’s technical competency and a representative of the type club must sign the application form.
Note: The applicant’s documented technical expertise will be evaluated against the vintage aircraft make, certification basis, and individual regulations for which the repair and/or alterations data approval is sought.
5. The goal of the FAA is to have vintage aircraft DERs have “spinner-to-tail” DER approval authority; therefore, they should be appointed to multiple delegations listed in appendix A to this order.
6. Once the base qualifications are verified, the DER may receive delegation for all makes of vintage aircraft of similar construction.
7. A vintage aircraft DER will not be allowed to make findings of compliance with foreign (CAA) regulations.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
Repair Specification ACOs will ensure the applicant for the special delegation of DER (RS-DER) RS-DER has the following experience before authorizing repair specification authority:
1. Experience in approving repair designs as a DER with the special delegation of major repairs, or major repairs and major alterations (or equivalent experience, for example, as an ACO engineer or Organization Authorization Designation unit member). The experience should be of sufficient quality and quantity to ensure the applicant will be able to execute the delegation appropriately. For example, the applicant should have demonstrated this by having approved more than a dozen major repairs in a year’s time.
2. Experience managing projects and being responsible for ensuring all applicable certification requirements for the repair are identified. This can be evidenced by overseeing others who develop and approve data that demonstrates compliance with the certification requirements, and ensuring compliance issues resulting from or associated with overlapping of engineering disciplines are resolved.
3. Experience being the primary contact with the FAA, both FSDO/CMO/IFO and ACO.
Note: A DER may be limited to working on repair specifications appropriate to their experience. For example, the FAA may limit a structures DER to airframe repair specifications. A DER may not be limited if their experience allowed them to manage repair specification data approvals in other technical areas with the support of authorized DERs in those areas.
DER with a delegation 1. A thorough working knowledge and understanding of of Airborne Electronic RTCA/DO-254[ ] (where [ ] indicates the latest revision of Hardware approval the document), Design Assurance Guidance for Airborne Electronic Hardware.
2. An understanding of and experience with RTCA/DO-254[ ] hardware life cycle data needed to demonstrate that the objectives of RTCA/DO-254 are fully met (for example, Plan for Hardware Aspects of Certification, Hardware Accomplishment Summary, Hardware Process Assurance Plan, Hardware Configuration Management Plan, Hardware Design Plan; Hardware Verification Plan, Hardware Validation Plan, Hardware Design Standards, and Traceability data). The DER should also demonstrate the ability to assess the quality of
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
hardware life cycle data and the development team’s adherence to approved plans, standards and procedures.
3. Familiarity with the systems safety assessment process, specifically, those portions that establish the hardware design assurance levels.
4. A demonstrated knowledge of the rationale for, and the significance of, each process and activity in the hardware life cycle, as well as its supporting standards, procedures, and documentation. The DER should be able to identify and evaluate the critical aspects and contents of each of the documents in RTCA/DO-254[ ].
5. Ability to distinguish between complex and simple electronic hardware. This should include the ability to: (1) evaluate the classification of the device as “simple” and its justification; (2) assess the test and analysis strategy; and (3) evaluate the test and analysis results to confirm verification coverage required for the “simple” classification of the electronic hardware.
6. Experience gained from participation in some technically responsible capacity over a complete airborne electronic hardware life cycle. This qualification may be satisfied by an aggregate of involvement in different airborne electronic hardware development programs and various roles in those programs.
7. Experience interacting with the phases of airborne electronic hardware development and testing processes addressed by RTCA/DO-254[ ], including use of the associated configuration management and process assurance. This experience should include significant responsible involvement in several of those phases.
8. Experience with the design of different kinds of airborne electronic hardware devices, such as Application Specific Integrated Circuits (ASIC), Programmable Logic Devices (PLD), Field Programmable Gate Arrays (FPGA), and other types of custom micro-coded devices.
9. Familiarity with Hardware Description Languages used for programming airborne electronic hardware, and an understanding of the types of verification required for using such languages.
10. Familiarity with various tools used in the design, verification, validation, and configuration control of airborne electronic hardware. Familiarity with available typical airborne electronic hardware tools to
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
facilitate the development, documentation, and consistency-checking processes is highly desirable.
11. Demonstrated knowledge of the sources of airborne electronic hardware anomalies, the relative merits of the types of verification processes and activities that are able to detect errors and anomalies, and the characteristics of a thorough verification program.
12. An understanding of the system and hardware design techniques that may be used to assign or reduce a hardware design assurance level (for example, redundancy, built-in-test, monitoring, circuit/function isolation, and dissimilarity). This should include the ability to assess the acceptability of proposed mitigation techniques relative to the required system integrity and reliability.
13. Experience in addressing errors in the different processes and activities where errors can be introduced in airborne electronic hardware (for example, handling of components, use of development tools, design, and the manufacturing/fabrication process).
14. Knowledge of hardware characteristics that can impact interfaces with software and other hardware components, including safety, integrity, and reliability aspects.
15. Experience with airborne electronic hardware verification process activities, including reviews, analyses, simulation/emulation, and testing.
16. Familiarity with post-certification airborne electronic hardware processes (for example, manufacturing quality control, factory configuration control, acceptance test procedures, factory installation and test equipment, production equipment control, and installation approvals for Technical Standard Order (TSO) authorization equipment).
17. Familiarity with airborne electronic hardware modification processes, including modifications to previously developed hardware, changes of aircraft installation, change of application or design environment, upgrading a design baseline, and conducting change impact analyses and regression testing and analyses.
18. The FAA requires a minimum level of successful experience before allowing a DER to approve data pertaining to airborne electronic hardware. The experience to be considered in relation to
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
airborne electronic hardware design assurance levels is as follows:
a. Level A Airborne Electronic Hardware. A DER should have demonstrated knowledge of the different design assurance considerations and strategies in RTCA/DO-254, Appendix B, including Functional Failure Path Analysis, Architectural Mitigation, Product Service Experience, and Advanced Verification Methods. A DER should have at least 1 year of successful experience reviewing Level A airborne electronic hardware data submittals before being designated to approve any Level A data.
b. Level B Airborne Electronic Hardware. A DER should have demonstrated knowledge of the different design assurance considerations and strategies in RTCA/DO-254, Appendix B, including Functional Failure Path Analysis, Architectural Mitigation, Product Service Experience, and Advanced Verification Methods. A DER should have at least 1 year of successful experience reviewing Level A or Level B airborne electronic hardware data submittals before being designated to approve any Level B data.
c. Level C Airborne Electronic Hardware. A DER should have at least 1 year of successful experience reviewing Level A, Level B, or Level C airborne electronic hardware data submittals before being designated to approve any Level C data.
d. Level D Airborne Electronic Hardware. According to AC 20-152, if RTCA/DO-254 is the proposed means of compliance for airborne electronic hardware Level D devices, then DER review of the life cycle data will not be needed. However, if a manufacturer chooses to use a design assurance practice other than RTCA/DO-254, then DER review of the life cycle processes and data may be needed. This will ensure Level D devices will perform their intended functions and the alternate method is acceptable. A DER may be designated to approve Level D data if the qualification criteria for appointment as a DER with airborne electronic hardware approval have been met (see above items 1. through 17.).
Note: 1: The appointing ACO will determine what limitations will be placed on the DER’s authority. These limitations should be expressed in the terms used in RTCA/DO-254 and must be defined in the DER’s authorization letter.
Table 4-1. Technical Appointment Criteria — Specialized — DER
DER Category Applicant Requirements
Note 2: Certain data approvals should be reserved for approval by the ACO. This includes the Plan for Hardware Aspects of Certification, Top Level Drawing or Hardware Configuration Index, and the Hardware Accomplishment Summary. For some systems and complex electronic hardware requiring design assurance Level A or B, the verification and validation data may also be reserved for approval by the ACO.
Note: A DER may be appointed for, or limited to, specific types of work. For example, a systems and equipment DER could be limited to handling approval of alterations to specific types of systems, such as hydraulic and pressurization, on only one airplane model.
405. Interface Appointment Criteria — DER.
a. Interpersonal skills, including the following:
(1) Command of the English Language — Spoken. All designees must have sufficient command of the English language to allow the designee to perform assigned functions.
(2) Command of the English Language — Written. All designees must have the ability to write clear, concise, informative, and meaningful documents and reports.
b. Integrity, professionalism, and sound judgment: All designees must possess and maintain a reputation in the aviation industry, their profession, and the community for a high degree of integrity, honesty, professionalism, dependability, sound judgment, and a cooperative attitude. (Company applicants must include a statement from the company attesting to these attributes.)
c. Three verifiable character references are required to substantiate that the applicant possesses integrity and sound judgment. These references may be the same persons used for technical references.
d. The applicant must have significant experience in a direct working relationship with the FAA office in which the applicant seeks appointment. The applicant’s experience must be related to the processing of engineering data pertaining to FAA approval of the type in which the applicant is seeking appointment. The applicant’s range of activities in obtaining FAA approvals must have been adequate enough to enable the FAA to determine that the applicant is cognizant of the technical and procedural requirements involved in obtaining such approvals and that the applicant is well-versed in all pertinent regulation(s).
Note: The criteria in paragraph d. above need not be met for identification as a candidate. The applicant must satisfy all other criteria.
e. The applicant’s place of residence must be in the United States, but U.S. citizenship is not a requirement for appointment.
f. For company DERs, the applicant must report to a level of management in the organization sufficient to enable the applicant to administer the pertinent regulations effectively without undue pressure or influence from other organizational elements.
g. The applicant must have the ability to maintain the highest degree of objectivity while performing authorized functions on behalf of the FAA.
h. The applicant’s position within a company should not result in any significant conflict of interest.
406. Standardization Appointment Criteria.
a. DER. These criteria verify that the DER applicant possesses knowledge of the designee program, pertinent regulations, directives, and related guidance material, by the applicant’s successful completion of the DER initial seminar.
b. DMIR/DAR. These criteria verify that the DMIR/DAR applicant possesses knowledge of the designee program, pertinent regulations, directives, and related guidance material, by the applicant’s successful completion of initial training.
407. FAA Employee Applicants. Current FAA employees will not be appointed as designees until their employment with the FAA has been terminated. FAA employees may not apply to the National Examiner Board (NEB) earlier than 120 days before their actual date of retirement or separation from the agency. A letter of recommendation must accompany the application from management of the applicant’s last assigned office in lieu of the three letters of reference. All other portions of the application package are required to be completed and returned because former employees must still substantiate the applicant’s experience while employed by the FAA or other experience within the aircraft industry. Appointments will be limited to functions performed while employed by the FAA or other experience within the aircraft industry.
408. Multiple Appointments. An individual may be appointed as more than one type of designee. For example: DAR and DMIR or DAR, DMIR, and DER, as long as all appointment criteria are met. In such cases, separate appointments will be made and separate certificates of designation issued. Separate entries will be required in the DIN for each appointment. A separate advisor should be identified for each functional organization with a DER and DAR appointment; the designee will report to two different offices and two advisors. If the delegations are in separate areas of responsibilities, but within the same geographic area, the two managing offices must ensure each office is aware of the delegations. If the delegations are in different geographic areas of responsibility, the two managing offices will determine which office will manage the delegation.
Note: A designee performing engineering and manufacturing DMIR/DAR functions (or other combination thereof) may not perform both functions on the same product or article. For example, a manufacturing DMIR/DAR cannot perform a conformity inspection on the same product or article for which they approved the design as a DER.
409. Supplier DMIR Applications.
a. Requests for appointment of a DMIR at a PAH’s approved supplier facility must be initiated by a letter from the supplier to the MIDO in the geographic area where the supplier is located. This letter must attest to the applicant’s qualifications, integrity, sound judgment, and cooperative attitude, and it must be accompanied by a completed Form 8110-14. The request for appointment also must contain a letter from the PAH detailing the need for the DMIR appointment. The MIDO in the geographic area where the supplier is located will coordinate the appointment, including determining the need and ability to manage the designee, with the PAH’s certificate management MIDO. If the supplier DMIR applicant is an existing DMIR, the MIDO in the geographic area where the supplier is located will determine if a new Form 8110-14 is required. If the addition of the supplier function codes constitutes an expansion of authority, a full application package will be required as described in paragraph 508 of this order.
b. A supplier DMIR will be limited to perform authorized functions on products produced under a TC/STC for the PAH only for which the designee is appointed.
Note: If a TC/STC applicant that does not hold a production approval is having articles manufactured at a supplier that does not hold a production approval, required conformity inspections must be performed by a DAR/ASI.
c. A PAH may supply articles to a TC/STC applicant that does not hold a production approval. In this case a qualified PAH DMIR (or a DAR) will perform any required conformity inspections. A TC/STC applicant that does not hold a production approval may make a written request to a PAH supplier to provide a DMIR to make conformity inspections on articles manufactured in that facility on the applicant behalf. This written request should include the project number and information, and the specific need for the DMIR. The PAH supplier will make a written request to their manufacturing managing office requesting the DMIR’s eCOA be amended to include this additional authorization. When the managing office approves the request and the eCOA is changed to reflect the additional authorization, the managing office will scan and attach these letters to the DMIR’s DIN record.
d. When revisions are sought to authorized functions listed on a DMIR’s COA, the PAH must submit a letter referencing the existing appointment and requested revisions. The managing office will determine if a new Form 8110-14 is required. Any PAHs added to a DMIR’s COA must be substantiated by a PAH’s letter of recommendation. The appointing MIDO must issue and process a new eCOA in accordance with chapter 5, AIR Designee Appointment Process, of this order and the DMIR will print the new eCOA from the DIN portal. The appointing office will notify the appropriate MIDO of any revisions to a supplier DMIR’s COA.
410. Appointment of DMIRs Outside the United States. Section 183.31(c) allows a DMIR to perform authorized function(s) at any location permitted by the FAA. A PAH or PAH’s approved supplier will make application for a DMIR appointment outside the United States in accordance with the applicable criteria found in this order. The application must be accompanied by adequate written justification providing all information (for example, work location, type of work, and duration) necessary for the FAA to render a judgment. A DMIR may be appointed and perform authorized function(s) outside the United States under the following conditions:
Note: Before appointing a designee outside the United States, the FAA managing office must comply with the requirements in FAA Order 8100.11, Decision Paper Criteria for Undue Burden and No Undue Burden Determinations Under 14 CFR Part 21.
a. The managing office may permit the appointment of a DMIR only when it can adequately supervise, monitor, train, and track the DMIR’s activity. The request will be denied if adequate oversight cannot be maintained.
b. The managing office will request information from the CAA to determine that the applicant has no history of regulatory violations from that country. If the applicant has a violation history, an evaluation must be conducted to ascertain the type of violation(s), any special or mitigating circumstance(s), and the attitude toward compliance with the CAA regulations. The selection and appointment process will continue in accordance with chapter 4, AIR Application Process, and chapter 5 of this order.
411. Appointment of DARs Outside the United States.
a. The FAA may appoint non-U.S. citizens who reside in and have a primary place of business in another country as manufacturing DARs. Managing offices must have the long-term capability and funds to make a minimum of one onsite visit per year to supervise, monitor, train, and track the DAR activity. These activities should be accomplished concurrently with other FAA activities. Applications must be accompanied by a letter from the CAA of the country, addressed to the appointing manager, stating that it has no objection to the DAR making findings of conformity/compliance on products/articles located in its country.
b. Appointing offices must request information from the CAA to determine whether the applicant has a history of regulatory violations and process the application in accordance with chapter 5 of this order.
Note: Comply with the requirements in FAA Order 8110.11, Decision Paper Criteria for Undue Burden and No Undue Burden Determinations Under 14 CFR Part 21 before appointing a designee outside the United States.
412. Appointment of DERs Outside the United States. The FAA will not appoint as a DER an individual who does not have a legal permanent residence in the United States. The FAA has determined the burden to the agency of managing a DER who does not reside in the United States outweighs any FAA need that might be met by appointing such a DER.
Chapter 5. AIR Designee Appointment Process
500. General. This chapter describes the procedure to process and evaluate an application. The selection and appointment process involves initial application review by the DPC, the appointing office manager’s determination of need and ability to manage the designation, and the evaluation by the assigned advisor and the EP. This section also describes the processing of applications for expanded authority and the process by which an applicant can be identified as a candidate. The ACO or MIDO will complete application processing within 90 days of receipt of an acceptable package.
501. Initial Application Processing.
a. The applicant submits the completed application package to the cognizant ACO or MIDO. All applications received will be given to the DPC for processing. Within 30 days of receipt, the DPC will review each application to ensure all necessary information has been provided.
(1) If the application is incomplete, the DPC will request that the applicant provide any missing information. A certificate from AFS-640 for completion of initial training is required as part of the application package for manufacturing designees.
(2) The DPC will check with the DIN to determine if the applicant has a previous designee record. If the applicant has had previous designations terminated because of misconduct, the DPC will deny the application and notify the appointing office manager.
(3) If a recent request for appointment by the applicant has been denied, the DPC will consult the appointing office manager to determine whether to continue with or deny the application.
b. When the package is acceptable, the DPC will―
(1) Contact the appointing office for the advisor’s name. The appointing office manager appoints an advisor who will have the primary responsibilities in the selection and appointment process for the assigned applicant.
(2) Send the applicant a letter that acknowledges receipt of the acceptable application package and identifies the assigned advisor. The letter should state that the applicant can expect an FAA decision within 90 days after receipt of an acceptable package.
(3) Ensure the required information is entered into the DIN. For manufacturing designees, the DPC will update the DIN training record to document successful completion of initial training based on the information provided by the applicant on the completion certificate issued by AFS-640.
(4) Prepare a designee file folder containing the application package.
c. When all initial application processing has been completed, the DPC will forward the designee file folder containing the application package to the evaluating office for action by the advisor.
502. Advisor’s Evaluation of the Application.
a. Upon receipt of the application package from the DPC, the advisor will accomplish the following:
(1) Consult the appointing office manager to determine FAA need and ability to manage. Need and ability to manage are based on a variety of factors such as project workload, geographic location, number of FAA employees, and ratio of designees to advisors. If there is an FAA need and a determination made that there are adequate FAA resources to manage the designee after appointment, the advisor will evaluate the application further. The appointing office manager will initial the Designee Appointment Tracking Document, items 1 and 2 (see appendix B, figure B-1 of this order) to document the FAA need and ability to manage decisions. If the appointing managing office manager determines that there is no FAA need, or the designation cannot be managed, the advisor will deny the application and document the decision in the DIN.
Note: The applicant does not have any appeal rights when there is no FAA need or ability to manage the designation. The appointing office(s) should write a courtesy letter notifying the applicant that the FAA is not accepting applications for the requested delegation and that the applicant may reapply at a future date.
(2) Conduct a preliminary review of the application package for general qualifications and scope, and determine if there is a regulatory violation history (see FAA Order 2150.3, Compliance and Enforcement Program). If the applicant has a violation history, an evaluation must be conducted to ascertain the type of violation(s) and any special or mitigating circumstances, or attitude toward compliance with FAA regulations.
Note: The ultimate decision for appointment of an applicant with a violation history must be the product of judgment and experience applied to the facts and circumstances of the individual case.
(a) For manufacturing designees, the advisor may obtain and review the violation history by using the Enforcement Information System or other means (for example, managing offices and character references). For example, if an applicant has an A&P mechanic’s certificate, a search of the Flight Standards Airman System would reveal if that person has had any violations. It is strongly recommended that the advisor conduct a thorough interview of each applicant’s character references.
(b) For manufacturing designees, the advisor will verify the applicant’s successful completion of initial training.
(c) For engineering designees, the advisor may have to rely solely on the character references provided by the applicant. It is strongly recommended that the advisor conduct a thorough interview of each applicant’s character references.
b. At the completion of the preliminary review, the advisor may deny the application. When denying an application, the advisor will document the justification and coordinate with the DPC and the office manager.
Continue reading ↓ 120 of 605 passages shown