Order 8100.15 Organization Designation Authorization Procedures
This document is cancelled. Cancelled by 8100.15A. Check the official source before relying on it.
ORDER 8100.15
Distribution: A-W (IR/FS/VN)-3; A-X (CD/FS)-3; A-FFS-0 (LTD); Initiated by: AIR-100/200/AFS-300 A-FAC-0 (ALL); AMA-220 (50 copies); AMA-250 (25 copies); AFS-600 (3 copies); AVR-20 (ALL); AEU-100/200
ORGANIZATION DESIGNATION AUTHORIZATION
PROCEDURES
8/18/06 DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
FEDERAL AVIATION ADMINISTRATION
RECORD OF CHANGES DIRECTIVE NO. 8100.15
CHANGE
TO
SUPPLEMENTS
OPTIONAL
CHANGE TO
SUPPLEMENTS
OPTIONAL
BASIC BASIC
FAA Form 1320-5 (6-80) USE PREVIOUS EDITION
Page i (and ii)
FOREWORD
This order establishes the procedures, guidance, and limitations of authority we (the Federal Aviation Administration, or FAA) grant to an organization under the Organization Designation Authorization (ODA) program. If you work for the Aircraft Certification Service or Flight Standards Service and are involved in appointment or oversight of delegated organizations, you must follow these procedures. This order also offers guidance to help designated organizations understand what we may authorize them to do, and the procedures they must follow.
BASIC BASIC
If you find any deficiencies, need clarification, or want to suggest improvements on this order, send a copy of FAA Form 1320-19, Directive Feedback Information (written or electronically), to the Aircraft Certification Service, Planning and Financial Resources Management Branch, AIR-530, Attention: Directives Management Officer. Form 1320-19 is on the last page of this order. You may also send a copy to the Aircraft Engineering Division, AIR-100, Attention: Comments to Order 8100.15. If you urgently need an interpretation, contact AIR-140 at 405-954-7066. Always use Form 1320-19 to follow up each verbal conversation.
Nicholas A. Sabatini Associate Administrator for Aviation Safety
TABLE OF CONTENTS
TABLE OF CONTENTS
Paragraph Page
Page iii
CHAPTER 1. INTRODUCTION
1-1. Purpose … 1 1-2. Distribution … 1 1-3. Effective Date … 1 1-4. General … 1 1-5. Changes To This Order … 2 1-6. Deviations … 2 1-7. Records Management … 2 1-8. Standard Procedures … 2
CHAPTER 2. PROGRAM OVERVIEW
CHAPTER 2. PROGRAM OVERVIEW
2-1. FAA Appointment of ODAs … 3 2-2. Eligibility for ODA … 3 2-3. Meaning of ODA Holder and ODA Unit … 3 2-4. Organization Management Team … 3 2-5. Transition of Existing Delegation Holders … 3 Figure 2-1. Existing Delegation Transition … 5 2-6. Types of ODAs … 5 2-7 Multiple ODA Types … 6 Figure 2-2. ODA Functions … 7 Figure 2-3. Airworthiness Certificate and Approval Functions … 8
CHAPTER 3. QUALIFICATIONS, RESPONSIBILITIES, AND AUTHORITY
CHAPTER 3. QUALIFICATIONS, RESPONSIBILITIES, AND AUTHORITY
3-1. Granting an ODA … 9 3-2. Reducing Designees … 9 3-3. ODA Holder Location … 9 3-4. ODA Holder Qualifications … 9 3-5. ODA Staff Qualifications … 10 3-6. Responsibilities … 11 3-7. Memorandum of Understanding … 12 3-8. Authority and Functions … 12 3-9. Procedures Manual … 13 3-10. Training … 15 3-11. Duration of Appointments … 15 3-12. Continued Eligibility … 16 3-13. Selection and Appointment of ODA Unit Members … 17 3-14. Self-Audit … 18 3-15 Work Activity … 19 3-16. Records … 19 3-17. Data Review and Service Experience … 20 3-18. Activity Outside the U.S … 20
8100.15 8/18/06
TABLE OF CONTENTS (CONTINUED)
TABLE OF CONTENTS (CONTINUED)
Paragraph Page
Page iv
CHAPTER 4. APPLICATION, SELECTION AND APPOINTMENT
4-1. Pre-Application Communication … 21 Figure 4-1. Appointing/Managing Offices … 21 4-2. Existing Delegated Organizations … 22 4-3. Application … 22 4-4. Selection Process … 23 4-5. Appointment … 26
CHAPTER 5. OVERSIGHT
CHAPTER 5. OVERSIGHT
5-1. Oversight Program … 27 5-2. Organization Management Team (OMT) … 27 5-3. Supervision Overview … 27 5-4. Supervision … 29 5-5. Delegated Organization Inspection Program … 33 5-6. Corrective Action … 33 5-7. Geographical Coordination … 34 5-8. ODA Renewal … 34
CHAPTER 6. DELEGATED ORGANIZATION INSPECTION PROGRAM
CHAPTER 6. DELEGATED ORGANIZATION INSPECTION PROGRAM
6-1. Inspection Program Overview … 37 6-2. Responsibilities … 37 6-3. Inspection Scheduling … 38 6-4. Inspection Planning … 39 6-5. Performing the Inspection … 41 6-6. Post-Inspection Activity … 43 Figure 6-1. Inspection Disagreement Resolution Flow Chart … 45
CHAPTER 7. SUSPENSION AND TERMINATION OF AN ODA
CHAPTER 7. SUSPENSION AND TERMINATION OF AN ODA
7-1. General … 47 7-2. Cause for Suspension or Termination of ODAs … 47 7-3. Coordination of Suspension or Termination Decisions … 48 7-4. Notification of Suspension or Termination … 48 7-5. Appeal Procedures … 48 7-6. Surrender of Records … 50 7-7. DIN Status … 50
TABLE OF CONTENTS (CONTINUED)
TABLE OF CONTENTS (CONTINUED)
Paragraph Page
Page v
CHAPTER 8. TYPE CERTIFICATION FUNCTIONS
8-1. General … 51 8-2. Eligibility … 51 8-3. Functions … 51 8-4. Limitations … 53 8-5. Records … 53 8-6. Type Certification Programs … 54 Figure 8-1. ODA Type Certification Process … 61 8-7. Off-Site Project Requirements … 63 8-8. Other Off-Site Activities … 65 8-9. Approval of Major Alteration or Major Repair Data … 66 8-10. Data Approvals in Support of STC Applicants … 66 8-11. Approvals of Alternative Methods of Compliance to Airworthiness Directives (AD) and AD Mandated Repairs … 67 8-12. Airworthiness Certification … 68 8-13. Special Flight Permits … 69 8-14. Procedures Manual Requirements … 69
CHAPTER 9. PRODUCTION CERTIFICATION FUNCTIONS
CHAPTER 9. PRODUCTION CERTIFICATION FUNCTIONS
9-1. General … 75 9-2. Eligibility … 75 9-3. Functions … 75 9-4. Limitations … 77 9-5. Records … 77 9-6. Production Certificate and PLR Changes … 77 9-7. TC/STC Conformity … 78 9-8. Airworthiness Certificates … 79 9-9. Special Flight Permits … 79 9-10. Export Airworthiness Approvals … 79 9-11. Procedures Manual Requirements … 80
CHAPTER 10. TECHNICAL STANDARD ORDER AUTHORIZATION HOLDER FUNCTIONS
CHAPTER 10. TECHNICAL STANDARD ORDER AUTHORIZATION HOLDER FUNCTIONS
10-1. General … 83 10-2. Eligibility … 83 10-3. Functions … 83 10-4. Limitations … 83 10-5. Records … 84 10-6. Conformity Functions … 84 10-7. Airworthiness Approvals … 84 10-8. Procedures Manual Requirements … 84
8100.15 8/18/06
TABLE OF CONTENTS (CONTINUED)
TABLE OF CONTENTS (CONTINUED)
Paragraph Page
Page vi
CHAPTER 11. SUPPLEMENTAL TYPE CERTIFICATION FUNCTIONS
11-1. General … 85 11-2. Eligibility … 85 11-3. Functions … 85 11-4. Limitations … 87 11-5. Records … 88 11-6. Alteration Locations … 88 11-7. Supplemental Type Certification Programs … 88 11-8. Off-Site Project Requirements … 95 11-9. Other Off-Site and International Activitities … 98 11-10. STC Projects Involving Foreign-Registered Aircraft or Foreign State of Design Products … 98 11-11. Finding Compliance With Foreign Regulations … 99 11-12. Airworthiness Certification … 99 11-13. Special Flight Permits … 99 11-14. Procedures Manual Requirements … 100
CHAPTER 12. MAJOR REPAIR, MAJOR ALTERATION, AND AIRWORTHINESS FUNCTIONS
CHAPTER 12. MAJOR REPAIR, MAJOR ALTERATION, AND AIRWORTHINESS FUNCTIONS
12-1. General … 103 12-2. Eligibility … 103 12-3. Functions … 103 12-4. Limitations … 104 12-5. Records … 105 12-6. Approving Major Alteration or Major Repair Data … 105 12-7. Airworthiness Certification … 106 12-8. Special Flight Permits … 107 12-9. Procedures Manual Requirements … 107
CHAPTER 13. PARTS MANUFACTURER APPROVAL FUNCTIONS
CHAPTER 13. PARTS MANUFACTURER APPROVAL FUNCTIONS
13-1. General … 109 13-2. Eligibility … 109 13-3. Functions … 110 13-4. Limitations … 111 13-5. Records … 112 13-6. PMA Test and Computation Approvals … 112 13-7. PMA Approvals Based on Licensing Agreement or STC … 115 13-8. Airworthiness Approvals … 118 13-9. Conformity Determinations … 118 13-10. Data Review and Service Experience … 119 13-11. Procedures Manual Requirements … 119
TABLE OF CONTENTS (CONTINUED)
TABLE OF CONTENTS (CONTINUED)
Paragraph Page
Page vii
CHAPTER 14. DESIGNEE INFORMATION NETWORK
14-1. Keeping the Designee Information Network Up To Date … 121 14-2. Designation Form … 121 14-3. ODA Numbers … 121 14-4. Status Definitions … 121
APPENDIX 1. SAMPLE FORMS AND LETTERS (32 PAGES)
APPENDIX 1. SAMPLE FORMS AND LETTERS (32 PAGES)
Figure 1. Sample FAA Form 8100-13, ODA Statement of Qualifications … 1 Figure 2. Sample ODA Application Checklist … 2 Figure 3. Sample ODA Letter of Designation … 3 Figure 4. Sample ODA Denial Letter … 4 Figure 5. Sample FAA Form 8100-9 Used for ODA STC Data Approval … 5 Figure 6. Sample FAA Form 8100-9 Used for ODA TC Data Approval … 6 Figure 7. Sample FAA Form 8100-9 Used for TC ODA Approval in Support of STC … 7 Figure 8. Sample FAA Form 8100-9 Used for TC ODA Repair Data Approval … 8 Figure 9. Sample FAA Form 8100-9 Used for MRA ODA Compliance Finding … 9 Figure 10. Sample Summary Activity Report … 10 Figure 11. Sample FAA Form 8100-11, Statement of Completion … 11 Figure 12. Sample FAA Form 8100-12, Production Limitation Record … 12 Figure 13. Sample ODA Supervision Record … 14 Figure 14. Sample Memorandum of Understanding … 16 Figure 15. Sample Conformity Inspection Plan … 19 Figure 16. Sample Inspection Notification Letter … 23 Figure 17. Sample Inspection Discrepancy Record … 24 Figure 18. Sample Inspection Report Cover Sheet … 25 Figure 19. Sample Inspection Survey Sheet … 26 Figure 20. Sample Inspection Report Transmittal Letter … 28 Figure 21. Sample PMA Supplement-Licensing-Page 1 … 29 Figure 22. Sample PMA Supplement-Test and Computations-Page 1 … 30 Figure 23. Sample PMA Supplement-STC-Page 1 … 31 Figure 24. Sample PMA Supplement-All Types-Page 2 … 31
8100.15 8/18/06
TABLE OF CONTENTS (CONTINUED)
Paragraph Page
Page viii
APPENDIX 2. SAMPLE ODA PROCEDURES MANUAL (13 PAGES)
APPENDIX 3. DELEGATED ORGANIZATION INSPECTION CRITERIA (56 PAGES)
APPENDIX 4. RELATED FAA PUBLICATIONS (2 PAGES)
APPENDIX 5. DEFINITIONS (3 PAGES)
APPENDIX 6. ACRONYMS (2 PAGES)
APPENDIX 6. ACRONYMS (2 PAGES)
Par 1-1 Page 1
CHAPTER 1. INTRODUCTION
1-1. PURPOSE. This order outlines the Federal Aviation Administration's (FAA) Organization Designation Authorization (ODA) program. Under this program, we (the FAA) can delegate certain types of authority to organizations. We wrote this order for Aircraft Certification Service (AIR) and Flight Standards Service (AFS) personnel, who manage delegated organizations. We also wrote this for organizations granted an ODA to act on the FAA's behalf. This order addresses how to qualify, appoint, and oversee organizations in the ODA program.
CHAPTER 1. INTRODUCTION
1-2. DISTRIBUTION. This order is distributed to the Washington headquarters branch levels of the Aircraft Certification Service, Flight Standards Service, and the Regulatory Support Division; to the Aviation System Standards Office; to the branch level in the Aircraft Certification directorates and regional Flight Standards divisions; to all Aircraft Certification Offices; to all Manufacturing Inspection District and satellite Offices; to all Flight Standards District Offices; to the Aircraft Certification Branch, and Operations and Airworthiness branches at the FAA Academy; to the Brussels International Policy Branch and Flight Standards Staff; and to all International Field Offices.
1-3. EFFECTIVE DATE. Each FAA managing office must immediately adopt the practices in this order concerning the selection and oversight of ODA holders. Any organization listed below must apply for and obtain an ODA by November 14, 2009 if it wants to retain its delegated authority:
• A holder of a Delegation Option Authorization (DOA), • A Designated Alteration Station (DAS),
• An operator or repair station authorized under Special Federal Aviation Regulation Number 36 (SFAR 36), or
• A Organizational Designated Airworthiness Representative (ODAR).
1-4. GENERAL.
a. Under title 49 section 44702(d), the FAA Administrator may delegate to a qualified private person a matter related to issuing certificates, or related to the examination, testing, and inspection necessary to issue a certificate the FAA Administrator is authorized by statute to issue under §44702(a).
b. We established the ODA program in 14 CFR part 183, subpart D, which addresses all FAA delegations to organizations. This program will replace the DOA, DAS, ODAR, and SFAR 36 delegation programs.
c. Because some ODAs involve both AIR and AFS functions, AIR and AFS personnel must work simultaneously or in coordination with each other to oversee these ODAs.
d. The ODA program does not affect how we delegate authority to individuals under 14 CFR part 183, subparts A through C. However, we anticipate that organizations that get an ODA will use significantly fewer individual designees.
8100.15 8/18/06
Page 2 Par 1-5
1-5. CHANGES TO THIS ORDER. The authority to revise or cancel material in this order rests with the Aircraft Certification Service, Aircraft Engineering Division (AIR-100), Production and Airworthiness Division (AIR-200) and the Flight Standards Service Aircraft Maintenance Division (AFS-300).
1-6. DEVIATIONS. You must follow the procedures in this order to ensure uniform administration of this directive. To deviate from this material, you must coordinate with – and get approval from – AIR-100, AIR-200, or AFS-300, as applicable. If deviation is necessary, be sure to substantiate and document the deviations, and get approval from your supervisor and AIR-100, AIR-200, or AFS-300, as applicable.
1-7. RECORDS MANAGEMENT. Refer to FAA Orders 0000.1, FAA Standard Subject Classification System; 1350.14, Records Management; and 1350.15, Records, Organization, Transfer, and Destruction Standards; or see your office Records Management Officer or Directives Management Officer for guidance on keeping or disposing of records.
1-8. CERTIFICATION ACTIVITY. Organizations that are not eligible for or do not want an ODA may continue to use standard certification procedures, including individual designees. Organizations with ODAs may perform some functions or projects under an ODA and other functions or projects using standard certification procedures, as approved by the FAA. However, effective November 14, 2009, FAA delegations to organizations under the DOA, DAS, ODAR and SFAR 36 delegation programs will be terminated.
1-9. REFERENCE MATERIAL. See the following for material referenced in this order:
Appendix 1 - Examples of forms, letters, and formats Appendix 4 - Related FAA publications Appendix 5 - Definitions Appendix 6 - Acronyms
Par 2-1 Page 3
CHAPTER 2. PROGRAM OVERVIEW
CHAPTER 2. PROGRAM OVERVIEW
2-1. FAA APPOINTMENT OF ODAs. We may not grant an ODA to every qualified applicant. We will only grant ODAs when we determine the following:
• The organization's FAA workload is large enough to warrant approval;
• The FAA will benefit from granting the ODA; and
• We have the resources available to manage the authorization.
2-2. ELIGIBILITY FOR ODA. Any organization consisting of two or more individuals may apply for an ODA. However, every organization is not eligible for every ODA type. For some ODA types, the organization must be a certificate holder or meet specific eligibility requirements. For example, only a parts manufacturer approval (PMA) holder can get a PMA ODA. Other program types are available to any type of organization.
2-3. MEANING OF ODA HOLDER AND ODA UNIT. An ODA holder is the organization to which we grant the ODA. It may be a certificate holder, such as a repair station or aircraft operator, or a consultant group. The ODA unit is the group of individuals (at least two) within the ODA holder that perform the authorized functions. For consultant groups, the ODA holder may consist entirely of the ODA unit. In this order, some requirements apply specifically to the ODA holder, others to the unit. Ultimately, the ODA holder must administer the ODA unit, and meet all requirements of this order.
2-4. ORGANIZATION MANAGEMENT TEAM. The organization management team (OMT) is the group of FAA personnel responsible for oversight of the ODA holder. See paragraph 5-2 of this order for information about OMTs.
2-5. TRANSITION OF EXISTING DELEGATION HOLDERS. The ODA rule provides for the existing DAS, DOA, and SFAR 36 authorization rules to be phased out on November 14, 2009. Additionally, ODARs will no longer be appointed under 14 CFR part 183, subpart A, and will have to be re-appointed as an ODA holder by the same date. Figure 2-1 shows how existing delegated organizations will transition into the ODA program.
a. The FAA's priority during the transition period will be to ensure that existing delegated organizations are appointed during that time. New ODA applicants will be appointed only if it will benefit the FAA. The ability of any particular FAA field office to appoint new ODA holders is variable, and depends on the number of existing delegated organizations they manage. During the initial 3 year period, we expect to appoint only those new applicants (those with no existing organizational delegation) with a history of a high level of certification work whose workloads could be better managed under an ODA.
b. Individual FAA managing offices will manage the transition of existing delegated organizations based on:
• Benefit to the FAA.
• The organizations level of certification activity.
• Benefit of other ODA applicants.
8100.15 8/18/06
Page 4 Par 2-5
c. First priority will be given to existing, eligible delegated organizations that have a high level of workload in new areas authorized under the ODA rule. For example, existing DASs that desire to have both STC and PMA functions under an ODA would be a higher transition priority than a DAS that would not be adding any ability under ODA. Additionally, it may be of more benefit to the FAA to appoint a new ODA with a higher workload than transition an existing organization with a lower workload.
d. Each FAA field office will develop its own management strategy for ODA applications based on the considerations discussed above. We anticipate that existing delegated organizations will cooperate with their managing offices in the submittal of their ODA applications. The FAA managing offices will work with their existing delegated organizations and develop a transition schedule that meets the organization's desired transition plan as much as possible based on workload and the factors listed above. Existing organizations are free to submit ODA applications as of November 14, 2006, but should be aware that review and processing of those applications will be prioritized as explained, and the FAA may not take action on any one application until a later date. Existing delegated organizations should apply for ODA not later than April, 2008 to ensure that they will receive their authorizations before their current authority expires.
e. We anticipate that DAS, DOA, and SFAR 36 organizations will be able to transition to an ODA program with minimal changes to their existing procedures. These organizations will have to submit applications and make minimal changes to their procedures manuals in order to be appointed under ODA. The FAA will review the certification activity and performance history of each existing delegated organization to determine whether it is still in the FAA's interest to appoint the organization as an ODA holder. We anticipate that there will be greater impact to existing ODAR organizations, which will have to develop new procedures, such as in-house training, which are not part of existing ODAR requirements. Existing authorized representatives for all types of delegated organizations may be granted the same level of authority under the ODA program without additional review of their qualifications.
f. The FAA will provide transition training for existing DAS, DOA, and SFAR 36 administrators to address the differences between ODA and existing DAS, DOA, and SFAR 36 programs. This training is required for the administrators of these organizations before an ODA will be issued. The FAA will also require ODA administrator training for new ODA applicants. This training will more comprehensively address all aspects of the ODA program. Because ODA represents a significant increase in requirements compared with the ODAR program, existing ODARs must attend this comprehensive applicant training.
Par 2-6 Page 5
FIGURE 2-1. EXISTING DELEGATION TRANSITION
FIGURE 2-1. EXISTING DELEGATION TRANSITION
Then the holder can obtain:
If a holder's
existing delegation authority is:
TC ODA
PC ODA
TSOA
ODA
STC ODA
MRA
ODA
PMA ODA
DAS X
DOA X X
SFAR 36 X
PC ODAR
or seeking TC/PC X
PMA ODAR X
Operator or
145 ODAR X
TSOA ODAR X
2-6. TYPES OF ODAs. There are six types of ODA programs shown in Figure 2-1. Each type has a chapter in this order that addresses qualifications and functions. To perform functions available to a certain ODA type, organizations must meet certain eligibility requirements. These organizations, when performing delegated functions, must follow all applicable FAA regulations and policies appropriate to those functions. See figures 2-2 and 2-3 of this order for an overview of the available functions. Other types of ODA programs may be added by the appropriate headquarters policy office by future changes to this order.
TSOA ODAR X
a. TYPE CERTIFICATION ODA (TC ODA). A TC ODA holder may manage and make findings for type certification programs. In addition to the engineering and manufacturing approvals that are part of the certification program, a TC ODA holder may issue airworthiness certificates, but may not issue an original type certificate (TC) or amended TC. A TC ODA is available to organizations holding a type certificate issued by the FAA.
b. PRODUCTION CERTIFICATION ODA (PC ODA). A PC ODA holder may issue airworthiness certificates and approvals, determine conformity, perform evaluation leading to amendment of its production limitation record, and approve minor changes to its quality control manual. To qualify for a PC ODA, an applicant must be an existing production certificate (PC) holder, or have applied for a TC and PC.
c. SUPPLEMENTAL TYPE CERTIFICATION ODA (STC ODA). Holders of an STC ODA may develop and issue supplemental type certificates (STCs) and related airworthiness certificates. An STC ODA is intended primarily for repair stations, operators, and manufacturers,
8100.15 8/18/06
Page 6 Par 2-6
but consultant groups with the required knowledge and experience may also qualify for an STC ODA.
d. TECHNICAL STANDARD ORDER AUTHORIZATION HOLDER ODA (TSOA ODA). Holders of a TSOA ODA may issue airworthiness approvals and determine conformity in support of FAA-managed certification projects. Only existing technical standard order (TSO) authorization holders qualify for a TSOA ODA.
e. MAJOR REPAIR, ALTERATION, AND AIRWORTHINESS ODA (MRA ODA). Holders of an MRA ODA may approve data for major repairs and alterations, issue airworthiness certificates and approvals, and perform aging aircraft inspections and records reviews. Repair stations, operators, and consultant groups are eligible for an MRA ODA.
f. PARTS MANUFACTURER APPROVAL ODA (PMA ODA). Holders of this ODA may issue PMA supplements based on test and computation approvals, STCs, or licensing agreements. Only existing PMA holders qualify for this ODA type.
2-7. MULTIPLE ODA TYPES. An organization that seeks an ODA may apply for as many types of ODA for which it qualifies. An organization may have separate procedures manuals for each type of ODA, or a common procedures manual that addresses all types of ODAs. We may require separate manuals if necessary to manage the organization. We will only issue one ODA letter of designation, and assign one ODA number. In the letter of designation, we will list each type of ODA and detail the authorized functions for each type.
Par 2-7 Page 7
FIGURE 2-2. ODA FUNCTIONS
FIGURE 2-2. ODA FUNCTIONS
AVAILABLE FUNCTIONS
CHAP 8
TC ODA
CHAP 9
PC ODA
CHAP 10
TSOA ODA
CHAP 11
STC ODA
CHAP 12
MRA ODA
CHAP 13
PMA ODA
APPROVE TECHNICAL DATA AND FIND COMPLIANCE TO THE AIRWORTHINESS
STANDARDS
8010 E 11010 E 13010 E
ISSUE STCS and/or AMENDMENTS 11020 E
ISSUE and REVISE PMA SUPPLEMENTS
BASED ON TEST AND COMPUTATIONS 13031 M
BASED ON TEST AND COMPUTATIONS 13031 M
BASED ON LICENSING AGREEMENT OR STC 13032 M
APPROVE OPERATIONAL AND REPAIR
INFORMATION 8040 E 11040 E 12040 E 13040 E
APPROVE AIRWORTHINESS LIMITATIONS
INFORMATION 8050 E 11050 E 12050 E 13050 E
ISSUE AIRWORTHINESS CERTIFICATES &
APPROVALS See Figure 2-3 for Airworthiness Functions
ESTABLISH CONFORMITY INSPECTION
ESTABLISH CONFORMITY INSPECTION
REQUIREMENTS 8070 E 9070 M 11070 E 13070 E, M
DETERMINE CONFORMITY OF PARTS & TEST
ARTICLES 8080 M 9080 M 10080 M 11080 M 13080 M
DETERMINE CONFORMITY OF TEST SETUP 8090 M 9090 M 10090 M 11090 M 13090 M
DETERMINE CONFORMITY OF INSTALLATIONS, INCLUDING TIA
INSPECTIONS ON A PRODUCT
INSPECTIONS ON A PRODUCT
8100 M 9100 M 11100 M 13100 M
PERFORM COMPLIANCE INSPECTIONS 8110 E 11110 E 13110 E
EVALUATE PRODUCTION LIMITATIONS
RECORD CHANGES 9120 M
APPROVE DATA FOR MAJOR ALTERATIONS
AND/OR MAJOR REPAIRS 8130, E 12130 E
PERFORM AGING AIRCRAFT INSPECTIONS
AND RECORDS REVIEWS 12140 O
APPROVE MINOR CHANGES TO QUALITY
APPROVE MINOR CHANGES TO QUALITY
CONTROL MANUAL/PROCEDURES 9150 M
PERFORM APPROVALS IN SUPPORT OF
OTHER TC ODA HOLDER PROJECTS 8160 11160 13160
Legend: Primary FAA Office – E=Aircraft Certification Office; M=Manufacturing
Inspection District Office; and O=Flight Standards District Office
OTHER TC ODA HOLDER PROJECTS 8160 11160 13160
NOTE: For function code descriptions and additional clarification, see specific chapters.
Underlined codes are available to consultant group organizations.
8100.15 8/18/06
Page 8 Par 2-7
FIGURE 2-3 AIRWORTHINESS CERTIFICATE AND APPROVAL FUNCTIONS
AVAILABLE FUNCTION CODES
CHAPTER 8
CHAPTER 8
TC ODA
CHAPTER 9
PC ODA
CHAPTER 10
TSO ODA
CHAPTER 11
STC ODA
CHAPTER 12
MRA ODA
CHAPTER 13
PMA ODA
ISSUE STANDARD AIRWORTHINESS
CERTIFICATES 9061 M 11061 M 12061 O
ISSUE SPECIAL AIRWORTHIENSS
CERTIFICATES 8062 M 9062 M 11062 M 12062 O
ISSUE DOMESTIC AIRWORTHINESS
APPROVALS 9063 M 10063 M 12063 O 13063 M
ISSUE EXPORT APPROVALS 9064 M 10064 M 12064 O 13064 M
ISSUE EXPORT APPROVALS 9064 M 10064 M 12064 O 13064 M
ISSUE EXPORT APPROVALS 9065 M 12065 O
ISSUE SPECIAL FLIGHT PERMITS 8066 M 9066 M 11066 M 12066 O
ISSUE SPECIAL AIRWORTHINESS CERTIFICATES FOR PRIMARY CATEGORY
AIRCRAFT
9067 M 11067 M
ISSUE SPECIAL AIRWORTHINESS CERTIFICATES FOR RESTRICTED CATEGORY
ISSUE SPECIAL AIRWORTHINESS CERTIFICATES FOR RESTRICTED CATEGORY
AIRCRAFT
9068 M 11068 M 12068 O
ISSUE PROVISIONAL AIRWORTHINESS
CERTIFICATES 9069 M
ISSUE REPLACEMENT FOR A LOST, STOLEN,
OR MUTILATED STANDARD OR SPECIAL
AIRWORTHINESS CERTIFICATE
110610 M 120610 O
Legend: Primary FAA Office – M=MIDO; and O=FSDO
NOTE: For function code descriptions and additional clarification, see specific chapters.
AIRWORTHINESS CERTIFICATE
Underlined codes are available to consultant group organizations.
Par 3-1 Page 9
CHAPTER 3. QUALIFICATIONS, RESPONSIBILITIES, AND AUTHORITY
3-1. GRANTING AN ODA. This chapter outlines the general ODA eligibility and qualification requirements. It also sets out the general procedures for getting and keeping an ODA, and describes the general functions and limitations that apply to all ODAs. We address the specific requirements for the various types of ODAs in chapters 8 through 13 of this order.
CHAPTER 3. QUALIFICATIONS, RESPONSIBILITIES, AND AUTHORITY
3-2. REDUCING DESIGNEES. The designee system leverages the FAA's resources by authorizing individuals and organizations to perform functions for the agency. Managing organizations is more efficient for the FAA than managing the activity of many individual designees. We expect an ODA applicant that employs individual designees to significantly reduce the number of designees for the type of ODA functions it seeks. An ODA holder may retain individual designees to operate under standard procedures, when necessary.
3-3. ODA HOLDER LOCATION. Each ODA holder must be located in the United States. However, ODA unit members may be located apart from the ODA holder's facility if agreed to by the OMT. An ODA holder may appoint ODA unit members in another country only after the OMT decides the ODA unit member's location poses no undue burden on the FAA. The ODA holder must make at least one on-site visit per year to manage the ODA unit member's activity. The ODA unit member must attend all required training, and meet with the OMT yearly if required by the OMT.
3-4. ODA HOLDER QUALIFICATIONS. Every applicant must meet the qualifications in this paragraph as well as the eligibility requirements in chapters 8 through 13 of this order for the specific type of ODA requested:
a. Integrity. The applicant's management, its ODA administrator, and the proposed ODA unit members must possess demonstrated integrity in their experience with the FAA.
b. Organizational Model. One key to the success of the ODA system is that the ODA holder's executive management fully supports the ODA unit. The ODA unit also must be free to do its duties. The organizational model for ODAs will vary significantly depending on the ODA holder's functions, size, and corporate structure. The model must meet the following:
(1) The ODA administrator must ensure that the organization performs all authorized functions in accordance with the regulations and applicable FAA policy. (Terms used in this order, such as "ODA administrator," are defined in appendix 5 of this order.) The ODA administrator must also ensure that the organization always complies with its ODA procedures manual. The ODA administrator must be in a position that provides him the authority to act in the FAA's interest.
(2) Each ODA unit member must be in a position that provides enough authority and time to perform his duties without pressure or influence from other parts of the organization.
(3) An ODA unit member must have no conflicting restraints placed on him while performing authorized functions. Additionally, an ODA unit member must not have responsibilities that conflict with those of the ODA unit.
8100.15 8/18/06
Page 10 Par 3-4
c. Experience. Each applicant must have experience and a thorough working knowledge of the FAA regulations, methods of compliance, policy, processes, and procedures applicable to the authorized functions sought. Additionally, applicants seeking a TC, STC, or PMA ODA must have a recent and successful history performing certification work and have completed projects as an organization. For these ODA types, newly formed organizations must complete projects under standard procedures in order to be eligible for ODA even if the ODA unit members are experienced individuals. An applicant for type and production certificates may be appointed as a PC ODA if it is expected to obtain a production certificate.
d. Resources. Each applicant must have sufficient administrative and technical resources to satisfy all the requirements of the requested authorization. It must employ an ODA administrator and have available an ODA unit consisting of the appropriate personnel capable of performing the authorized functions. The lead ODA administrator must be a full-time employee of the ODA holder. Other ODA administrators need not be full-time employees, but must meet all ODA administrator qualification requirements. Except for the administrator, an ODA unit may consist solely of individuals who are not employed full time by the organization.
e. Facilities. Each ODA holder's facilities must be in the United States. The facilities must be appropriate for the ODA sought, as detailed in chapters 8 through 13 of this order.
3-5. ODA STAFF QUALIFICATIONS. Qualifications for the ODA administrator and ODA unit follow:
a. ODA Administrator. The ODA administrator must have technical experience with the functions performed under the ODA and a broad range of management experience. This experience must enable him to manage the entire ODA unit activities effectively. The following are the minimum requirements for an ODA administrator:
(1) At least five years of working experience with the FAA on projects similar to those authorized under the ODA. This experience must include various levels of technical airworthiness responsibilities and experience (for example, compliance engineer, quality assurance inspector, manufacturing inspector, or airworthiness inspector), and management experience in one or more technical disciplines (such as, engineering, manufacturing, airworthiness, maintenance, or quality assurance).
(2) Comprehensive knowledge of FAA regulations, policies, and procedures applicable to the ODA functions.
(3) Demonstrated sound judgment and integrity.
(4) Sufficient technical knowledge, training, skill, and experience for the type of ODA sought.
b. Engineering and Flight Test ODA Unit Members.
(1) An engineering or flight test ODA unit member must meet the qualifications for a DER. We define these qualifications in FAA Order 8100.8, Designee Management Handbook. The ODA unit members need to meet only those requirements for the functions and areas they will
Par 3-5 Page 11
perform. However, the requirement to have direct working experience with the FAA may be satisfied by having direct working experience within an ODA holder's or other delegated organization.
(2) Qualification Requirements for an ODA Unit Member Making Findings to Foreign Requirements. The OMT may authorize an ODA holder to make findings of compliance with foreign regulations in support of TC or STC validation programs. Each ODA unit member authorized to make such findings must thoroughly understand the foreign requirements and be knowledgeable of their application. This knowledge typically will be evidenced by participation on previous validation programs with the foreign authority and the FAA. The ODA unit member listing must identify, for each ODA unit member, the foreign requirements to which the ODA unit member is authorized to make findings.
c. Manufacturing and Maintenance ODA Unit Members.
(1) Each ODA unit member performing airworthiness, conformity, production or maintenance inspections must meet the qualifications to perform those inspections in FAA Order 8100.8. However, the requirement to have direct working experience with the FAA may be satisfied by having direct working experience within an ODA holder's or other delegated organization.
(2) Each ODA unit member determining conformity of installations must have five years of experience performing conformity inspections of installations on a product.
(3) Each ODA unit member performing type inspection authorization (TIA) inspections must have five years of experience inspecting aircraft systems installations and be able to determine airworthiness of the aircraft before flight testing.
(4) Each ODA unit member performing TIA inspections involving weight and balance of aircraft must have knowledge of weight and balance practices described in FAA Advisory Circular (AC) 120-27, Aircraft Weight and Balance Control.
(5) Each ODA unit member determining conformity of compliance test setups must have two years of experience performing conformity inspections of compliance test setups.
3-6. RESPONSIBILITIES. ODA holders and units must follow the FAA regulations, directives, policies, guidance, and procedures as applicable to the authorized functions. The responsibility for finding compliance with the regulations and applicable policy remains with the ODA holder. The ODA holder is responsible for the activity of the ODA unit and ODA administrator.
a. ODA Holder. The ODA holder must ensure that its ODA administrators and ODA units remain free to perform their authorized functions in accordance with FAA regulations. In addition to performing their authorized functions, the ODA unit members must have enough time and resources to keep up to date on the current FAA regulations, directives, and guidance applicable to the authorized functions.
8100.15 8/18/06
Page 12 Par 3-6
b. ODA Administrator. The ODA administrator manages the ODA unit activities and communicates with the OMT. The ODA administrator must ensure that the ODA unit has sufficient organizational authority and resources to perform its authorized functions in accordance with FAA requirements. The ODA administrator must report to a level of management that is senior enough to enable the ODA unit to administer duties for the FAA, without undue pressure or influence from other organizational segments or individuals. The ODA administrator must ensure that the organization follows the procedures in its procedures manual and that the processes comply with all applicable FAA regulations and policy. If the ODA holder has more than one ODA administrator, a lead ODA administrator must be identified.
c. ODA Unit. Each ODA unit member must be aware of, and avoid potential conflicts of interest between, his responsibilities to the FAA and his role as the ODA holder's employee. Each ODA unit member must:
(1) Comply with the procedures in the approved procedures manual.
(2) Meet the qualifications for his specific functions under the ODA.
(3) Cooperate with the FAA when the FAA oversees the ODA holder.
d. Separation of Duties. ODA holders and unit members should be aware that the delegated functions performed as an individual designee are separate and distinct from the functions performed as an ODA unit member.
3-7. MEMORANDUM OF UNDERSTANDING.
a. ODA Holder's Commitment. An ODA holder agrees to use the same care, diligence, judgment, and responsibility when performing the authorized functions as the FAA would use in performing the function. This commitment starts at the senior management level of the ODA holder and extends through the ODA administrator, ODA unit, and the rest of the applicant's organization. As proof of that commitment, senior management of the organization and the FAA managing office(s) will sign a memorandum of understanding (MOU) that outlines the charter, authority, and responsibility of the ODA holder.
b. Preparing an MOU. The prospective OMT and ODA holder jointly prepare the MOU. The ODA holder's senior management and FAA's managing office(s) must sign the MOU before issuing the ODA. Also, any time a signatory of the MOU changes, the replacement must sign a revised MOU. If an ODA holder's new senior management refuses to sign the MOU, we must terminate the ODA. Appendix 1, figure 14 of this order contains an example of an acceptable MOU. All personnel within the ODA holder that manage ODA unit members in any capacity must read and understand the MOU.
3-8. AUTHORITY AND FUNCTIONS.
a. Functions Available. We list the functions we may grant in figures 2-2 and 2-3 of this order. Each chapter in this order that covers an ODA type gives specific function code descriptions. Limitations for each ODA type are given in chapters 8 through 13 as well. Individual limitations will be identified in the ODA letter of designation and the approved procedures manual.
Par 3-8 Page 13
b. Authorized Functions. We will list the functions we authorize in the ODA letter of designation. In the letter of designation, we will also list any limitations the FAA deems appropriate. See appendix 1, figure 3 of this order for an example of an ODA letter of designation. To add functions, an ODA holder must apply in accordance with 14 CFR §183.43 and paragraph 4-3 of this order. The FAA must approve any changes in functions before they may be performed.
c. Products, Parts, Processes, or Appliances Selected. The ODA is limited to the products, parts, processes, or appliances identified in the procedures manual.
3-9. PROCEDURES MANUAL. Each ODA holder must perform all authorized functions in accordance with its FAA-approved procedures manual. The procedures manual must be available to all members of the ODA unit.
a. Content. The procedures manual may incorporate any previous agreements between the ODA holder and the FAA managing offices that comply with the limitations of this order. The procedures manual must contain at least the following (See appendix 2 of this order for format and chapters 8 through 13 for detailed requirements.):
(1) Cover page with signature blocks for the FAA managing office(s) and ODA administrators.
(2) General – table of contents, log of revisions, list of effective pages.
(3) Procedure for revising the procedures manual and obtaining approval of revisions.
(a) Definition of manual changes which don't require OMT approval.
(b) Method of documenting OMT approval of changes.
(c) Method of documenting and determining approval requirements for changes in facilities or organizational structure.
(4) Preface and Introduction, including procedures for FAA and ODA holder communications.
(5) Authorized functions and limitations.
(6) Description of the ODA holder and ODA unit organizational structure and responsibilities.
(7) ODA administrator and unit member duties and responsibilities.
(8) Required capabilities and ODA unit positions.
(9) The location and procedure for maintaining a list of ODA unit members. The list must contain the names, location, name of the company (if other than ODA holder), signatures, and responsibilities of ODA unit members. Revisions to the list must be provided to the FAA.
8100.15 8/18/06
Page 14 Par 3-9
(10) Procedures to select ODA unit members, and coordinate ODA unit member selections with the FAA.
(11) Description of the training courses each ODA unit member and ODA administrator must take, and where the training will take place. Include both standardization, recurrent, and inhouse training.
(12) Self-audit procedures and responsibilities.
(13) Procedures to maintain all applicable FAA guidance material.
(14) Duration of the ODA.
(15) Maintenance of Eligibility.
(16) Acknowledgement of the FAA's right to inspect the ODA holder or unit.
(17) Procedures for performing continued airworthiness functions, including investigation and resolution of service difficulties, potentially unsafe, or non-compliant conditions.
(18) Procedures for performing authorized functions.
(19) Records maintenance and submittal requirements.
(20) Corrective action procedures.
(21) Procedures for obtaining and maintaining related regulatory and guidance material.
(22) Procedures to report manufacturing activity, if applicable.
(23) Appendices:
• Memorandum of Understanding.
• Organization charts of ODA holder and unit and company interface.
• Facility descriptions and addresses of ODA unit members, including remote locations.
• ODA unit position descriptions and required qualifications.
• Sample forms used within the ODA system.
• Sample forms.
• Certification plans.
b. Approval. The OMT must review and approve those changes that require approval before the ODA unit performs any function affected by the change. Approval by the OMT will be indicated by FAA signature on the log of revisions page.
Par 3-10 Page 15
3-10. TRAINING.
a. ODA Holder-Provided Training. An ODA holder must provide training to its ODA administrator and unit members to ensure continued compliance with the approved procedures manual, the regulations, and applicable FAA policies. An ODA holder must provide this training before authorizing an ODA unit member to perform a delegated function. ODA unit members must receive this training at least every two years. An ODA holder must allow the FAA to review the training materials and attend any training session. An ODA holder must incorporate changes to the training material as required by the FAA. The training must explain:
(1) The functions delegated to the authorization.
(2) The ODA holder's processes, and its procedures manual.
(3) The ODA unit member's authority and responsibility when performing authorized functions.
(4) Applicable FAA regulations, policy, and guidance material. Temporary or limited use ODA unit members are only required to receive that ODA holder training commensurate with their involvement in the project. For example, an engineering ODA unit member performing a burn test or manufacturing ODA unit member performing specific part conformity inspections at a supplier location would not need training on all of the organization's functions and procedures. The ODA holder must provide the ODA unit member sufficient training on the specific procedures related to the ODA unit member's functions.
b. FAA Seminars. Each ODA unit member, in addition to the ODA holder's training, must attend the following FAA-sponsored training:
(1) Each ODA administrator must attend a delegation workshop at least every two years.
(2) Each ODA unit member must attend FAA training seminars. This includes those seminars that individual designees performing similar functions are required to take by other FAA Orders, such as FAA Order 8100.8 or FAA Order 8130.33, Designated Airworthiness Representatives: Amateur-Built and Light-Sport Aircraft Certification Functions. Additionally, ODA unit members performing functions specific to an ODA, such as evaluation of production limitation record changes, must attend seminars as required by the OMT.
c. Standardization Workshops. If required by the OMT, ODA unit members must attend FAA standardization workshops. Standardization workshops are subject-specific and usually developed and presented by FAA personnel or industry personnel as needed.
3-11. DURATION OF APPOINTMENT. An ODA is effective until the expiration date listed on the letter of designation. See paragraphs 4-5 and 5-8 of this order for guidance on the allowed duration of an appointment.
a. Transferability. An ODA is not transferable.
8100.15 8/18/06
Page 16 Par 3-11
b. Change in Ownership. A change in ownership of the ODA holder which results only in a name change with no change in organizational structure, etc., may be executed by reissuing the ODA letter of designation and the MOU, along with revising the procedures manual to reflect the new name.
c. Change to the ODA Unit. A change in the ODA unit that involves ODA administrators, structure within the ODA holder, or changes to the ODA holder or ODA unit, may change an organization's eligibility for ODA. The ODA holder must notify its OMT lead of anticipated organizational changes to determine whether the changes will impact the authorization and how they will be handled.
3-12. CONTINUED ELIGIBILITY. To maintain eligibility, an ODA holder must:
a. Notify the OMT lead within 48 hours of any change that would affect the ODA holder's ability to meet the requirements of its authorization. A notification due on Saturday, Sunday, or a holiday may be delivered on the next working day.
b. Comply with the requirements in its approved procedures manual.
c. Maintain a staff of qualified ODA unit members.
d. Implement corrective and remedial action for deficiencies identified by the FAA.
e. Not perform an authorized function if a change in the facilities, resources, or organizational structure affects how the ODA holder performs that function. This includes a move to a new location or the inability of the ODA holder to accommodate the ODA unit or records needed to perform the authorized function. The ODA holder may perform that function only after it notifies the OMT lead of the change, and the OMT documents and approves the change as required in the ODA holder's procedures manual.
f. If an ODA holder's basis of eligibility is a PC, the ODA holder cannot perform any authorized function if it moves its principal manufacturing facility or adds another facility. The ODA holder must notify the OMT of the change in accordance with 14 CFR §21.147 since a PC is not transferable (see 14 CFR §21.155). In this case, the company would have to apply for a PC extension or a new PC in accordance with 14 CFR §21.133.
g. If an ODA holder's basis of eligibility is a PMA, the ODA holder cannot perform any authorized function if it moves its principal manufacturing facility or adds another facility. The ODA holder must notify the OMT of the change in accordance with 14 CFR §21.303. In this case, the company would have to apply for a new PMA or an extension to its production approval.
h. If an ODA holder's basis of eligibility is a TSOA, the ODA holder cannot perform any authorized function if it moves its principal manufacturing facility or adds another facility. The ODA holder must notify the OMT of the change since a TSOA is not transferable in accordance with 14 CFR §21.621. In this case, the company would have to apply for TSOA in accordance with 14 CFR §21.607.
Par 3-13 Page 17
3-13. SELECTION AND APPOINTMENT OF ODA UNIT MEMBERS.
a. Overview. An ODA holder must select qualified ODA unit members. The ODA holder's procedures manual must contain its ODA unit member selection and approval process and documentation. Additionally, in some cases the OMT may review ODA unit member appointments before the ODA holder may add a new ODA unit member to the staff. See paragraph 3-13d of this order. The ODA unit member selection process must include coordination with the OMT regarding each proposed ODA unit member. The OMT must inform the ODA holder if any information in the FAA databases indicates that the proposed ODA unit member has demonstrated a lack of care, judgement, or integrity.
b. Existing Designees or ODA Unit Members at Another Delegated Organization. An ODA holder can appoint a prospective ODA unit member that is an existing designee without evaluating his qualifications if he will perform the same functions within its ODA unit. The ODA holder must maintain evidence of the ODA unit member's designee authority. An ODA unit member for another delegated organization may be similarly appointed if the other delegated organization provides evidence of the ODA unit member's authority and limitations. The ODA unit member must have experience on the same type and complexity of projects performed by the ODA holder. If the prospective ODA unit member is expected to perform any functions outside the scope of his current authority, the ODA holder must evaluate him for the additional functions according to paragraph 3-13c of this order.
c. Others. The ODA holder must evaluate each prospective ODA unit member that is not currently a designee or ODA unit member using a process and preparing documentation similar to that used by the FAA to evaluate designee applicants. For more information, see FAA Order 8100.8.
d. FAA Review of ODA Unit Member Appointment Decisions. It is the FAA's intention for ODA holders ultimately to appoint ODA unit members without OMT concurrence on appointment decisions. However, the OMT may decide to review an ODA holder's unit appointments until the ODA holder has proven that it can appoint ODA unit members that meet the qualification requirements.
(1) During the initial evaluation of ODA applicants, all proposed ODA unit member appointment packages should be reviewed by the OMT prior to appointing the ODA holder.
(2) For a period of two years after the initial ODA appointment, selection decisions for proposed ODA unit members, who are not currently designees or ODA unit members at other delegated organizations, may be reviewed by the OMT prior to the ODA unit member performing any authorized function for the ODA unit. The OMT should review enough appointment decisions to determine that the ODA holder is appointing qualified ODA unit members.
(3) After two years, the OMT should not need to review any ODA unit member appointment decisions unless:
(a) There are documented problems with the ODA holder's appointment process or performance. The OMT must document these problems and actively pursue corrective action with
8100.15 8/18/06
Page 18 Par 3-13
the ODA holder to improve the ODA holder's appointment process or performance. The appointment records of ODA unit members must be reviewed during subsequent oversight or inspections, or;
(b) The ODA holder has not had sufficient activity appointing ODA unit members.
e. ODA Unit Performance Problems. If the OMT identifies performance issues with an ODA unit member, the OMT must document the deficiency and require corrective action by the ODA holder, which may include removal of that ODA unit member from the ODA unit staff.
f. Appointment of ODA Unit Members at Foreign Locations. Appointment of ODA unit members at foreign locations may not pose an undue burden on the FAA. If the ODA holder desires to appoint an ODA unit member at a foreign location, it must get OMT concurrence on the location and functions to be performed by the ODA unit member. The ODA unit member is subject to the same training and oversight requirements as domestic ODA unit members.
3-14. SELF-AUDIT. The ODA holder must perform self-audits that evaluate the ODA unit members, the ODA processes, and compliance with all applicable FAA regulations and policy. A self-audit must be performed annually, and as requested by the OMT. The self-audit does not replace the FAA inspection required by this order. The procedures manual must contain the ODA holder's general audit procedures.
a. Personnel. The self-audit must include evaluation of the ODA unit members using the processes and criteria contained in FAA Order 8100.8 and Order 8300.10, Airworthiness Inspector's Handbook, as appropriate. The self-audit must include review of individual ODA unit members' work for accuracy. This includes ODA unit members located at suppliers or at other locations away from the ODA holder's facility.
b. Procedures. The self-audit must include evaluation of the procedures used to perform all authorized functions and the other requirements of the authorization, including ODA unit appointment and training, and service difficulty support.
c. Compliance with Procedures. The self-audit must evaluate whether the ODA holder complies with its procedures manual.
d. Self-Audit Records. The ODA holder must maintain records of its self-audits and submit copies to the OMT within 14 calendar days of completion.
e. Corrective Action. The ODA unit will review proposed corrective actions before submittal to the FAA.
f. Self-Disclosure. Pursuant to FAA Order 2150.3, Compliance and Enforcement Program, the FAA will not seek a civil penalty for regulatory violations if the ODA holder promptly notifies us of the noncompliance and meets certain other criteria. See Order 2150.3 and AC 00-58, Voluntary Disclosure Reporting Program, for more information.
Par 3-15 Page 19
3-15. WORK ACTIVITY. The ODA unit must complete and document its manufacturing and airworthiness work on the summary activity report, as described in FAA Order 8100.8. The OMT will determine how often an ODA holder must submit this report.
3-16. RECORDS. The ODA holder must ensure that the records described below are maintained. The ODA holder must also ensure the records specific to the authorizations described in chapters 8 through 13 are maintained. The records may be kept by the ODA holder, its suppliers, or others, as agreed to by the OMT. The ODA holder must also keep any records required for any certificates or authorizations it holds in addition to an ODA. At the OMT's request, an ODA holder must make the records available for examination at any time without undue delay. The ODA holder must make the records usually maintained by suppliers available at its facility for FAA inspections when requested. The ODA holder must identify all records and submit them to the OMT lead as soon as the ODA is surrendered or terminated.
a. The following must be retained for the duration of the authorization:
(1) Any records generated and maintained under the DAS, DOA or SFAR 36 regulations.
(2) For approvals and certificates issued under the ODA:
(a) The application and data required to be submitted by the regulations.
(b) The data and records documenting the ODA unit's approval, determination of compliance, or review.
NOTE: Airworthiness certificates and approvals need only be retained for two years, except those issued in support of a type certification project, which must be retained indefinitely.
(3) A list of the products, components, parts, or appliances for which ODA unit members have issued a certificate or approval.
(4) The names, responsibilities, qualifications, and example signature of the individuals who perform, or have performed, functions for the ODA unit.
(5) A copy of each manual approved by the ODA unit.
(6) Training records for ODA unit members and ODA administrators.
(7) All other records required by the approved ODA procedures manual.
(8) Any correspondence between the ODA holder and the OMT related to functions or activity performed with the authorization.
(9) The procedures manual, including all revisions.
b. The following must be retained for five years:
(1) Records of the ODA holder's self-audits and implementation of corrective action.
8100.15 8/18/06
Page 20 Par 3-16
(2) Records of any reported service difficulties associated with any design approval or certificate (including TCs, STCs, PMA by test and computation, and repair and alteration data) issued under the ODA.
c. Records Storage and Identification. The OMT and the ODA holder must agree on how to store and identify all required records for future retrieval. Certification records should be arranged by project number for easy retrieval. All ODA documentation and data must be consistent with that required by the FAA for its own records and organized in a manner that is compatible with the FAA records control system described in FAA Order 1350.14.
3-17. DATA REVIEW AND SERVICE EXPERIENCE. The ODA holder must provide continued support for approvals or certificates issued under ODA procedures in accordance with 14 CFR §183.63. Procedures for monitoring service information, investigation, and FAA notification must be included in the procedures manual.
a. Other Data Reporting Requirements. An ODA holder must comply with all existing applicable reporting requirements in the FAA regulations, such as 14 CFR §21.3.
b. Service Difficulty Monitoring. The ODA holder must monitor any service information available to it that is associated with approvals or certificates it holds that were issued under its ODA authority.
c. FAA Notification. For any approvals or certificates issued under an ODA, the ODA holder must notify the OMT lead of any item it identifies that:
(1) Might result in an unsafe condition.
(2) Requires corrective action.
(3) Does not meet the airworthiness standards.
d. Investigating Safety Concerns.
(1) For any approvals or certificates issued under an ODA, the ODA holder must investigate potentially unsafe, or non-compliant conditions in any product, part, article, or appliance, as required by the FAA.
(2) An ODA holder must report to the FAA the results of the investigation and any action it takes or proposes. The ODA holder must submit any information it has to support FAA corrective action if further action is necessary to ensure the safe operation of the product.
3-18. ACTIVITY OUTSIDE THE U.S. The ODA holder must notify the OMT prior to performing any function in a foreign country. The OMT must notify foreign Civil Aviation Authorities (CAA) of any ODA holder activity according to existing policy. The OMT will coordinate any necessary technical assistance support from bilateral partners through the CAA, in lieu of ODA holder personnel, if the CAA restricts the use of ODA holder personnel. When required for TC, or production approvals, the OMT will develop an undue burden decision paper as described in FAA Order 8100.11.
Par 4-1 Page 21
CHAPTER 4. APPLICATION, SELECTION AND APPOINTMENT
CHAPTER 4. APPLICATION, SELECTION AND APPOINTMENT
4-1. PRE-APPLICATION COMMUNICATION. A prospective ODA applicant must discuss with the FAA its desire to obtain an ODA before formal application. We issue ODAs at our discretion. Each prospective applicant must confirm whether we need to appoint the organization and whether we have the resources to manage its organization. An organization must begin discussions with the appropriate appointing offices (as defined in figure 4-1 of this order) before preparing the application contents. The appointing office must inform the applicant if we do not need the authorization or if we do not have the resources to manage the authorization. The appointing offices must give applicants feedback on their proposed organizational structure to determine if it is adequate before they submit the application.
FIGURE 4-1. APPOINTING/MANAGING OFFICES
FIGURE 4-1. APPOINTING/MANAGING OFFICES
If the application is for:
And the applicant seeks:
Then the appointing office is the geographic:
And the evaluation panel also includes these managing offices:
And the lead managing office is:
TC ODA ACO MIDO AEG ACO
PC ODA MIO MIDO MIDO
TSOA ODA MIO MIDO MIDO
STC ODA ACO ACO MIDO FSDO
STC ODA ACO ACO MIDO FSDO
AEG
ACO
MRA ODA Only data approval functions
ACO ACO ACO
MRA ODA Both airworthiness and data approval functions
FSDO ACO FSDO
MRA ODA Only airworthiness functions
FSDO FSDO FSDO
PMA ODA Only airworthiness or production functions
MIO MIDO MIDO
PMA ODA Both engineering and airworthiness functions
ACO ACO MIDO AEG ACO
ACO ACO MIDO AEG ACO
FAA Offices: ACO-Aircraft Certification Office AEG-Aircraft Evaluation Group FSDO-Flight Standards District Office (includes Certificate Management Office) MIDO-Manufacturing Inspection District Office (includes Certificate Management Office, Certificate Management Unit, and Manufacturing Inspection Satellite Office) MIO-Manufacturing Inspection Office
8100.15 8/18/06
Page 22 Par 4-2
4-2. EXISTING DELEGATED ORGANIZATIONS. An existing DAS, DOA, SFAR 36 or ODAR organization must apply for an ODA according to paragraph 4-3 of this order. However, it need not provide detailed experience and qualification information on the proposed individuals within the ODA units if the ODA unit members will be performing the same functions as currently authorized. The appointing office and evaluation panels for these organizations do not need to review the qualifications of existing staff members who are qualified under existing delegation programs, but must consider and determine that the applicant satisfies the other appointment considerations.
4-3. APPLICATION. Applications must be submitted to the appropriate appointing office as shown in figure 4-1 of this order. If an applicant is applying for more than one type of ODA that will involve multiple appointing offices, it should coordinate with all appropriate appointing offices prior to submitting its application. The appointing offices will establish a lead office responsible for accepting the application and conducting the evaluation. An appointing MIO may delegate selection and appointment responsibilities to the MIDO. Each application must include:
a. FAA Form 8100-13, ODA Statement of Qualifications (appendix 1, figure 1 of this order).
b. A cover letter stating the authority and limitations requested for the authorization, including the products for which the authorization will be used. The cover letter must also contain a brief statement describing the applicant's eligibility under 14 CFR §183.47.
c. A detailed description of how the applicant meets the eligibility and qualification requirements defined in paragraphs 3-4 and 3-5 of this order, and the specific eligibility requirements defined in chapters 8 through 13 of this order.
d. A detailed description of the applicant's proposed ODA setup, including the ODA holder's organizational structure, the ODA unit's relationship to the applicant's organization, and facilities.
e. The ODA administrator's name, experience, and qualifications in a resume that clearly demonstrates that the proposed ODA administrator meets the qualifications of chapter 3.
f. A list of the proposed ODA unit members and information outlining the experience, qualifications, proposed functions, and limitations of each ODA unit member. Existing DAS, DOA, SFAR 36, and ODAR organizations need not provide experience and qualifications information on current staff members unless the staff members will be authorized to perform different functions under the ODA.
(1) If the applicant does not currently hold a DAS, DOA, SFAR 36 or ODAR authorization, the applicant must evaluate the proposed ODA unit members to determine that they meet all qualifications before application. The applicant must use a process that is similar to that used by the FAA to evaluate designee applicants. See FAA Order 8100.8. Proposed ODA unit members that are existing designees need not be evaluated if they will be performing the same functions as under a current designation.
Par 4-3 Page 23
(2) If the applicant proposes to use ODA unit members at locations outside the U.S., the applicant must include (with its application) a letter from the host country CAA. In the letter, the aviation authority should state it has no objection to an ODA unit member performing his authorized functions in its country.
g. A draft procedures manual that includes the information required by paragraph 3-9 of this order, and the specific information outlined in the procedures manual example in appendix 2 and chapters 8-13.
4-4. SELECTION PROCESS.
a. Initial Application Screening.
(1) The appointing office will screen each application to verify that:
(a) All required documentation is complete.
(b) Appointing the organization will be a benefit to the FAA.
(c) The FAA has the resources to manage the organization and its activity.
(d) The organization meets the eligibility requirements of 14 CFR §183.47 and chapters 8 through 13 of this order.
(2) If the FAA does not need, or does not have the resources to manage a particular ODA applicant, the appointing office must prepare a denial letter for the office manager's signature. (See appendix 1, figure 4 of this order.) Further, if the appointing office determines that the applicant is ineligible, it prepares a denial letter. The appointing office must inform the applicant if it needs additional information to determine the applicant's eligibility.
b. Evaluation Panel (EP) Makeup.
(1) If an application passes the initial screening, the appointing office must organize an EP of FAA personnel that will evaluate the application. An appointing office representative will manage the EP. The EP will consist of the following:
• Representatives from each relevant FAA organization in figure 4-1 of this order.
• Technical specialists from all areas proposed for the authorization.
NOTE 1: The EP may consist of the prospective OMT members for the organization, or the appointing office may use a standard panel for all applicants. See paragraph 5-2 of this order for information about the OMT.
NOTE 2: The appointing office must inform the appropriate headquarters office representative(s) of all ODA applications it receives. Headquarters specialists from AIR-100, AIR-200, or AFS-300 may participate in evaluation panel activity as they determine necessary. Each headquarters office will determine its participation based on the desired functions and the need to be involved in the appointment decision.
8100.15 8/18/06
Page 24 Par 4-4
(2) The EP must be qualified, familiar with the functional areas of delegation requested, and experienced with the applicable certification processes.
c. Appointment Considerations. The EP must consider the following to determine whether we will grant the ODA:
(1) The applicant must employ or have available a staff of qualified personnel appropriate to the authorization requested.
(2) The applicant must have adequate resources, facilities in the United States, equipment, tools, and manuals appropriate for the authorization.
(3) The ODA administrator(s) and unit must possess integrity, sound judgment, and a cooperative attitude.
(4) The organization must have a history of enough work to justify the appointment.
(5) The FAA must have the appropriate resources to oversee, manage, and support the appointment.
(6) The ODA administrator(s) must meet the qualifications of paragraph 3-5a of this order.
(7) The procedures manual must contain the information required by the regulations and this order.
d. Evaluation of the Application. The EP will review each application to determine whether the applicant qualifies for the authorization. The EP will thoroughly evaluate the application, the proposed procedures manual, the applicant's qualifications, the proposed ODA administrator's and ODA unit members' qualifications, and the organization's resources and structure. The EP must verify the accuracy and authenticity of the information in the application. The EP must verify that the information in the application and procedures manual complies with all applicable regulations and this order.
(1) Evaluation Panel Documentation. The EP must create and maintain documentation such as meeting minutes, email, or other correspondence about its evaluation.
(2) Interviews. The EP may interview the proposed ODA administrator, ODA unit members, or ODA applicant's management to verify the information in the application and determine whether the ODA applicant understands the requirements its organization must meet. While interviewing staff members, the EP may evaluate their knowledge of the certification procedures and technical responsibilities for which the ODA holder will be responsible.
(3) Site Visits. The EP may conduct site visits to evaluate an organization's facilities and abilities. Although existing certificate holders usually have existing facilities known to the FAA that may not require inspection, the EP will usually need to inspect consultant groups' facilities to verify they have the facilities necessary for the authorization.
Par 4-4 Page 25
(4) Procedures Manual Review. The EP must approve each applicant's procedures manual prior to appointment. During an evaluation, the EP must review the proposed procedures manual and ensure that it:
(a) Contains the information required by paragraph 3-9 of this order.
(b) Contains procedures that comply with all FAA orders pertaining to the functions described.
e. Denial of ODA Applications. The appointing office will notify the applicant if it denies its application. The appointing office must send the applicant the denial in writing via registered mail within 30 days of the decision. The denial letter must explain the reasons for the denial and detail what steps the applicant must take before the FAA will reconsider the application. (See appendix 1, figure 4 of this order for an example of the ODA denial letter.)
f. Appeals. If denied, an applicant may usually appeal the FAA decision in writing and request a review by an appeal panel. Denial decisions based on failure to attend required training, lack of benefit to the FAA or the FAA's inability to manage the organization may not be appealed. An applicant must submit its appeal within 60 calendar days of receiving notification of the denial.
(1) Appeal Panel. An appeal panel will consist of at least two managers and an engineer or inspector or flight test pilot from the geographic directorate, Manufacturing Inspection Office (MIO), and/or Flight Standards Regional Office (RO) as appropriate for the application. The appeal panel will consider all available information and may interview the applicant, applicant's staff, and evaluation panel personnel. The appeal panel may also invite other persons as needed at its deliberations. The appeal panel will reach a decision by consensus and all decisions are final.
(2) Functioning of the Appeal Panel.
(a) The appeal panel must determine if the appointing office conducted the appointment process properly. If the appeal panel finds discrepancies, it must take appropriate actions to ensure the integrity of the appointment process. To determine whether the appointing office conducted the appointment process properly, the appeal panel may interview members of the EP and review:
• The documentation in the applicant's file, • The EP's written justification for the denial, and • Other information it determines appropriate.
(b) The appeal panel must complete its deliberations within 45 calendar days from the date of the appeal, and must document its decision. Each panel member must sign the decision before the panel sends it to the directorate or regional office manager. The directorate or regional office manager will notify the applicant and appointing office of the appeal panel's decision by registered mail within 15 calendar days of the appeal panel's decision.
8100.15 8/18/06
Page 26 Par 4-4
(3) Appeal Panel Decisions. The appeal panel may:
(a) Uphold the previous decision;
(b) Override the previous decision with a new decision and provide appropriate justification; or
(c) Request that any part of the appointment process be repeated citing new information that the EP must review, or issue additional instructions and clarifications to the EP. The appeal panel may direct that the previous EP review the application, or it may direct the appointing office to appoint a new EP.
4-5. APPOINTMENT. If an EP approves an application, the OMT and ODA holder must prepare an MOU, as described in paragraph 3-7 of this order. The appointing office managers and at least one member of the applicant's senior level management – typically the organization's chief executive officer – sign the MOU. After completing the selection process (including getting the MOU signed), the appointing office will provide the applicant a letter of designation. The letter of designation must be signed by the OMT's office manager(s). The letter of designation must note the organization, types of ODA, authorization number, and expiration date for the ODA. The ODA letter of designation must also include the location of facilities and the functions and limitations of the authorization. The scope of the limitations may be in any form appropriate to the authorization. For example, limitations may be imposed based on a lack of certain experience, equipment, or limited to certain types of aircraft. See appendix 1, figure 3 of this order for a sample letter of designation. New ODAs will be granted for two years; existing delegated organizations may be granted an ODA for up to five years. See paragraph 5-8 of this order for appointment duration considerations for existing delegated organizations.
Par 5-1 Page 27
CHAPTER 5. OVERSIGHT
5-1. OVERSIGHT PROGRAM. The FAA's oversight program for delegated organizations is based on a systems approach to managing and supervising an organization. Oversight consists of supervision, addressed here, and inspections, which are addressed in chapter 6. We will focus on how an organization performs and its approved systems and procedures. We will oversee the organization as necessary to ensure that it performs adequately. The oversight program includes supervising and evaluating an organization's:
CHAPTER 5. OVERSIGHT
• System, personnel, and procedures;
• Projects and activities; and
• Overall performance.
5-2. ORGANIZATION MANAGEMENT TEAM (OMT). An OMT of FAA personnel oversees the ODA holder. The OMT includes members of the Aircraft Certification and Flight Standards field offices and AEG as needed to oversee the ODA holder. Participation will vary depending on the functions the ODA holder is authorized to perform. The OMT members must be knowledgeable and experienced in the functions the ODA unit performs.
a. The OMT lead coordinates the OMT's activity and serves as the focal point for communication with the ODA holder. The manager of the appointing office (see figure 4-1 of this order) selects the OMT lead.
b. An ACO's OMT members oversee all design approval and type certification procedures. The ACO also oversees the engineering and flight test functions performed by the ODA unit. The OMT must include ACO engineers from all authorized technical disciplines.
c. Manufacturing and Flight Standards OMT members oversee the authorized inspection and airworthiness procedures and functions. In addition, the Flight Standards OMT member will inform the OMT of any applicable change in the ratings or limitations of the ODA holder's repair station or operator certificates.
d. An AEG representative is responsible for acceptance of Instructions for Continued Airworthiness (ICA) and maintenance and operational issues on certification projects.
5-3. SUPERVISION OVERVIEW. In supervising an ODA holder, the OMT guides, manages, and provides performance feedback to the ODA holder. Supervision involves the FAA working and interacting with the ODA unit. Supervision consists of the following:
a. Managing the Organization's Activity.
(1) Defining and Understanding the Authority and Limitations of the Organization. The procedures manual defines an ODA holder's authority and limitations. The ODA holder's authority and limitations determine the functions it may perform. The OMT must ensure that the ODA holder's authority and limitations continue to be appropriate based on the organization's capability, experience, and history.
8100.15 8/18/06
Page 28 Par 5-3
(2) Approving the Organization's Procedures. By approving the procedures, the OMT ensures that the functions performed by the organization result in products and approvals that comply with FAA regulations and policies. The OMT must:
(a) Approve Procedures Manual Changes. Procedures manual changes address the authority or limitations of the organization, the organization's system model, or changes in the procedures for performing authorized functions. The OMT must approve procedures manual changes before the ODA holder implements them.
(b) Ensure ODA Unit Members Are Approved. The OMT must ensure that the ODA holder follows its procedures for selecting ODA unit members. The procedures must follow the process defined in paragraph 3-13 of this order.
(3) Managing Program Activity. For TC, STC, and PMA programs, the final step in authorizing certification activity is the OMT review of the program notification letter. The OMT must determine whether the ODA holder may perform its authorized functions on a particular project. The OMT must review each program notification letter and determine what FAA involvement is required. The OMT may delegate all aspects of the program, or retain some parts for FAA approval as it determines necessary.
b. Guidance and Feedback.
(1) Providing Guidance. The OMT will help each ODA holder get required directive and policy material. Most FAA regulations, directives, and ACs of interest to ODA holders are available on the FAA's website. The OMT should provide copies of any needed material not available via the Internet. The OMT must ensure the ODA holder has the information and instruction necessary for it to perform its authorized functions.
(2) Feedback. The OMT must provide feedback to the ODA holder about its performance. The OMT should notify the organization of any problems with its performance as soon as possible. If the feedback requires corrective action, the OMT must notify the ODA holder as described in paragraph 5-6 of this order.
c. Assessing Performance.
(1) Review of the Organization's Work. As determined necessary, the OMT must review the ODA unit's work and data for accuracy and completeness. The OMT will take into consideration the amount of the review on the organization's experience, the safety impact of the work being reviewed, the quality of work performed on previous projects, and the ODA unit member performing the function. Previous service difficulties should be considered when deciding the amount of review needed. The OMT must review samples of completed project records, such as airworthiness, conformity, compliance, and type design data. If the OMT requires personal meetings or inspections with the ODA holder or unit, it should coordinate them through the ODA administrator.
(2) Review of Self-Audits. The OMT must review the self-audit reports generated by the ODA holder for possible trends and items requiring corrective action. The OMT lead must coordinate the review with the other OMT members, and coordinate corrective actions in
Par 5-3 Page 29
accordance with paragraph 5-6 of this order if necessary. The OMT must ensure that self-audits address all of the ODA holder's authorized functions, and that the ODA holder performs them annually.
(3) Verifying compliance with procedures. The OMT must verify that the authorization holder complies with the approved procedures manual and referenced internal processes.
d. Maintaining Oversight Documentation. Proper documentation provides the OMT with the information it needs to oversee the organization properly. Documentation also provides a history of the organization's performance, in case OMT members change or the ODA holder seeks additional authority.
(1) The OMT lead will maintain a file for each authorization he manages. (The OMT members must provide any records not available to the OMT lead.) The file must contain at least the following as applicable:
(a) Approved ODA application package.
(b) Evaluation Panel documentation and rationale.
(c) Copy of the letter of designation and memorandum of understanding.
(d) General correspondence (non-project-specific) between the ODA holder and the OMT.
(e) Copy of the current procedures manual.
(f) Delegated organization supervision records and inspection reports.
(g) Copy of summary activity reports (if applicable).
(h) Enforcement history.
(i) Self audit reports.
(j) Copies of the organization's A-3 operations specifications showing the status of ratings, limitations, and capabilities list (repair stations and operators).
(2) The other OMT members must maintain a file documenting their specific activity in support of the OMT. Their files should include:
(a) Supervision records.
(b) Documentation of their input regarding projects performed by the organization.
5-4. SUPERVISION. The level of supervision depends on the ODA holder's experience, history, and past performance as well as the technical complexity and safety impact of the functions or projects it performs. The OMT members must complete the Delegated Organization
8100.15 8/18/06
Page 30 Par 5-4
Supervision Record (see appendix 1, figure 13 of this order) to document their supervision activities.
a. Required Evaluation Items. The OMT must assess annually the required evaluation items on the Delegated Organization Supervision Record. The OMT should meet and budget annually to establish a strategy for assessment of those items. The strategy should consider which OMT members will assess each item.
b. Coordinating Supervision Activity. The OMT lead will coordinate all supervision activity. The type of coordination will vary depending on the size and complexity of the ODA holder and OMT. If the OMT consists of only a few people, it may be appropriate to inform all OMT members of any activity related to the organization. For larger OMTs, like those overseeing TC ODA holders, it may be more practical to coordinate within technical disciplines, which would report their activity and findings to the OMT lead. The entire OMT will decide exactly how it will coordinate its supervision activity. Regardless of the arrangement, the OMT members must provide the OMT lead with supervision records documenting their supervision visits to the organization.
c. Planning Supervision Visits. Each OMT member should notify the OMT lead of any planned supervision activity at the organization's facility. The OMT lead should notify the ODA administrator of the planned visit. If the OMT has issues with any approvals issued by the organization or other performance issues, the OMT should coordinate them with the ODA administrator. If necessary, the OMT may make unannounced visits.
d. Engineering Supervision. Engineering OMT representatives can accomplish most of their supervision activity by reviewing data. This may not require on-site visits to the organization's facility. The OMT will determine the number of visits needed. At least one engineering OMT representative must make at least one supervision visit to the ODA holder's facility each year, in addition to the inspection requirements of chapter 6. The OMT member may combine this supervision visit with specific project activity, such as witnessing tests or participating in flight tests. However, the focus of the visit must be for the OMT member to:
(1) Review approved test plans and data such as compliance substantiation and type design data.
(2) Discuss self-audit results.
(3) Review implemented corrective actions.
(4) Review project files.
(5) Review internal training and training records.
(6) Review ODA unit member selection decisions and records.
(7) Provide the latest guidance and policy.
(8) Interact with the ODA unit members.
Par 5-4 Page 31
e. Manufacturing Supervision. Manufacturing OMT representatives oversee manufacturing activity primarily through direct interaction with the ODA unit, which requires visiting the ODA holder's facility. They can tailor the number of visits to the facility, but must visit the ODA holder at least once a year. These visits are in addition to the inspection requirements of chapter 6. They should base the number of visits on the ODA unit's experience and effectiveness of previous certification efforts. The frequency of visits will depend on the size of the organization, level of activity, and past performance. For smaller ODA holders or those with a low-level activity or no performance problems, manufacturing OMT representatives may need only one or two visits a year. Quarterly visits may be more appropriate for ODA holder's with increased complexity. During the visit, the manufacturing OMT member will:
(1) Determine compliance with regulatory requirements.
(2) Identify safety issues.
(3) Observe ODA unit members performing airworthiness or conformity inspections.
(4) Discuss self-audit results.
(5) Review implemented corrective actions.
(6) Review project files.
(7) Review internal training and training records.
(8) Review ODA unit member selection decisions and records.
(9) Provide the latest guidance and policy.
(10) Interact with the ODA unit members.
f. Flight Standards Supervision. The Flight Standards OMT representatives oversee the maintenance and operational activity through direct interaction with the organization. This requires visiting the organization. The minimum number of visits will be identified through the National Work Program and may be tailored based on the ODA holder's activity level. These visits may be performed in conjunction with other surveillance activity. During the visits to the facility, the Flight Standards OMT member will:
(1) Determine compliance with regulatory requirements.
(2) Identify safety issues.
(3) Observe ODA unit members performing aging aircraft, airworthiness or conformity inspections.
(4) Discuss self-audit results.
(5) Review implemented corrective actions.
8100.15 8/18/06
Page 32 Par 5-4
(6) Review certification files.
(7) Review internal training and training records.
(8) Review ODA unit member selection decisions and records.
(9) Provide the latest guidance and policy.
(10) Interact with the ODA unit members.
g. Aircraft Evaluation Group Supervision. The AEG's primary activities are to coordinate and review the Instructions for Continued Airworthiness, and support the ACO in determining operational suitability. Since the FAA does not delegate AEG functions to the organization, supervision activity by the AEG is usually limited to its participation during the certification program. The AEG will not normally visit the facility other than during inspections, but may do so if they determine a visit is necessary.
h. Documenting Supervision. The OMT will document supervision activity and significant communications with the ODA holder using the Delegated Organization Supervision Record in appendix 1, figure 13 of this order. The record is used to document both general supervision activity and any unsatisfactory performance.
(1) Required Evaluation Items. The OMT must evaluate the applicable items listed on the record at least once a year. Each OMT member must evaluate each of the items applicable to his technical discipline. Not every interaction with the ODA holder needs to be recorded, but every supervision visit to the organization's facility must be recorded. The OMT member performing the supervision should rate each item assessed as satisfactory, unsatisfactory, or not applicable. If an evaluation item is not assessed during the activity, leave the item blank. Corrective action must be implemented for all items rated as unsatisfactory.
(2) Text Blocks on Back of Form.
(a) Summary of Visit or Communication. Provide a summary of activity performed during any visit or important communications with the organization not otherwise documented. For visits, the summary should include details on how the evaluation items were assessed.
(b) Notable Conditions Encountered. A notable condition is any item or condition of interest that does not require corrective action, but warrants documentation. Highlight the notable conditions found. These may be items to assess during the next visit, or areas of interest to other OMT members.
(c) Items Requiring Corrective Action. Describe any evaluation item rated as unsatisfactory, or any other condition determined to need corrective action. Provide specific details of any unsatisfactory condition and check the box on the front page indicating corrective action is required. The OMT lead must coordinate with the other OMT members regarding items identified as needing corrective action. If the OMT lead concurs that corrective action is required, he must notify the ODA holder in accordance with paragraph 5-6 of this order.
Par 5-4 Page 33
(3) Coordinating Supervision Visit Findings. The OMT member performing the supervision activity should communicate his observations with the ODA administrator (if possible) and any ODA unit members involved in the reviewed activity. The ODA administrator should be told of any items identified as needing corrective action and informed that he will be further notified of such items.
5-5. DELEGATED ORGANIZATION INSPECTION PROGRAM. Under the inspection program described in chapter 6, the OMT inspects all aspects of the ODA holder's performance. It assesses both system-level procedures and compliance, how the ODA holder manages the ODA unit, and the ODA unit's technical proficiency and judgment. The inspection is a means for the OMT to assess whether:
• The ODA holder's procedures are adequate,
• The ODA unit has complied with the procedures, and
• The ODA unit makes technical decisions that are acceptable.
5-6. CORRECTIVE ACTION. The OMT must ensure the ODA holder takes corrective action to address non-compliances and problems with the organization's procedures or performance.
a. Regulatory Non-compliances. The OMT lead must notify the ODA holder of any violations of the regulations (other than non-compliances with the airworthiness standards), in accordance with FAA Order 2150.3.
NOTE: The OMT lead must be familiar with the FAA's compliance and enforcement program and must attend the FAA's compliance and enforcement training. If he has not, he must coordinate any compliance and enforcement activity with other members of the OMT who are familiar with the program's requirements. Manufacturing and flight standards OMT members usually have experience with compliance and enforcement procedures.
b. Non-compliance with the Airworthiness Standards and Potentially Unsafe Conditions. If an ODA unit approval or certificate results in a potentially unsafe product or a product not meeting the airworthiness standards, the OMT lead must immediately notify the organization of the unsafe condition or non-compliance and:
(1) Assess how the condition affects safety to determine whether we will issue an airworthiness directive (AD) to correct the condition on products in service.
(2) Pursue AD action if necessary.
NOTE: The FAA uses the AD process to mandate product changes or repairs for unsafe conditions. If a non-compliant condition in a product does not result in an unsafe condition, the OMT may ask the organization to correct the condition. The OMT must document when the ODA holder does not take corrective action for noncompliant conditions. The OMT will consider this when assessing the ODA holder's performance.
8100.15 8/18/06
Page 34 Par 5-6
(3) Require the ODA holder to:
(a) Determine the cause of the condition.
(b) Determine whether the problem is systemic or isolated in nature.
(c) Review the procedures that led to the approval and determine if the procedures are adequate and if qualified ODA unit members performed them.
(d) Develop any proposed corrective or remedial action.
(e) Submit its determination of the cause of the condition and proposed remedial action within 30 calendar days.
(4) Evaluate the cause of the condition and proposed remedial action in conjunction with the ODA holder as warranted.
(5) Verify that appropriate corrective or remedial action is implemented.
c. Other Conditions Requiring Corrective Action. The OMT lead will notify the ODA holder of any condition requiring corrective action. The OMT must document the condition on a supervision record or inspection report in the FAA's files and notify the ODA holder of the item in writing. The OMT must notify the ODA holder within 30 calendar days of identifying the condition. The ODA holder must submit its determination of the cause of the condition and proposed remedial action within 30 calendar days. The OMT lead must retain the organization's response and any related correspondence in the OMT's files.
d. Following Up on Corrective Action. The OMT must ensure the ODA holder implements corrective action. All corrective action must be verified during a visit to the facility. The OMT will track and re-evaluate all items requiring corrective action after the ODA holder takes corrective action.
5-7. GEOGRAPHIC COORDINATION. FAA personnel may need to oversee ODA holders with facilities in different geographic areas. The OMT lead will coordinate with the FAA offices having geographic responsibility. The geographic FAA office will supervise at the additional facility, if necessary.
5-8. ODA RENEWAL.
a. Renewal Intervals. The FAA will appoint a new ODA holder for two years. At renewal, the OMT must determine whether the ODA holder continues to comply with the requirements for delegation and the need for the authorization continues. The OMT may reappoint for a period of two to five years. The OMT will select the duration based on its experience with the ODA holder and the complexity of approvals.
b. Request for Renewal. An ODA holder must submit a letter requesting renewal of its ODA at least 60 calendar days prior to expiration. If the ODA holder does not request renewal, the OMT should initiate termination action. The renewal letter must include an overview of the activity performed under the ODA, and identify any increase in activity planned for the next
Continue reading ↓ 120 of 541 passages shown