Radar Vectors
FAA Order Cancelled Issued Sep 12, 2006 AIR-40 155 pages Copy saved Nov 18, 2026

Order 8100.14A Procedures for Working with European Community on Airworthiness Certification & Continued Airworthiness

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (2 of 155 pages). Check the original, as some words may be misread.

Federal Aviation

Administration

Memorandum

Date: DEC 2 2011

To: Al Spence, Strategy and Investment Analysis Division, AIO-020

Cc: Angeline Garrett, AIR-510, AIR DMO

From: Chris Carter, Manager International Policy Office, AIR-40

Prepared by: Walt Dillon, Foreign Specialist, AIR-40 ext 58943

Subject: Cancellation of Order 8100.14A, Interim Procedures for Working with the European Community on Airworthiness Certification and Continued Airworthiness – dated September 7, 2008.

This memorandum cancels Order 8100.14A, Interim Procedures for Working with the European Community on Airworthiness Certification and Continued Airworthiness – dated September 7, 2008.

Order 8100.14 was issued to provide interim policy and guidance on how to interact with the European Aviation Safety Agency (EASA) and the National Aviation Authorities of European Union (EU) Member States for the purposes of type, production, and airworthiness certification, and continued airworthiness of aeronautical products while the FAA was negotiating an international agreement with the EU.

This Order is considered obsolete now that the new U.S. / EU aviation safety agreement has entered in force. The Technical Implementation Procedures of the agreement provides procedures and guidance for our workforce when interacting with EASA. Continued reference to Order 8100.14A may result in confusion.

For the reasons mentioned above, we consider this order obsolete.

TECHNICAL IMPLEMENTATION PROCEDURES

TECHNICAL IMPLEMENTATION PROCEDURES

FOR

AIRWORTHINESS AND ENVIRONMENTAL

CERTIFICATION

BETWEEN THE

FEDERAL AVIATION ADMINISTRATION

OF THE UNITED STATES OF AMERICA

AND THE

EUROPEAN AVIATION SAFETY AGENCY

OF THE EUROPEAN Union

Revision 1

October 19, 2011

TABLE OF CONTENTS

Implementation Procedures i Revision 1, October 2011

SECTION I GENERAL Page

SECTION I GENERAL Page

1.0 Purpose … 1-1

1.1 Communications … 1-1

1.2 Reserved … 1-4

1.3 Certification Oversight Board Procedures … 1-4

1.4 Applicable Requirements, Procedures, and Guidance Material … 1-6

1.5 Entry into Force and Termination … 1-6

1.6 Definitions … 1-7 SECTION II DESIGN APPROVAL PROCEDURES

2.0 General … 2-1

2.0 General … 2-1

2.1 Design Approval Procedures for Type Certificates … 2-4

2.2 Design Approval Procedures for Supplemental Type Certificates … 2-8

2.3 Procedures for Approval of Manuals, including Flight Manuals … 2-13

2.4 Evaluation of Operational and Maintenance Aspects … 2-13

2.4 Evaluation of Operational and Maintenance Aspects … 2-13

2.5 Design Approval Procedures for Technical Standard Order (TSO) and European Technical Standard Order (ETSO) Design Approval … 2-14

2.6 Acceptance of Non-TSO Functions … 2-21

2.7 Acceptance of Equipment Standards and Aeronautical Databases … 2-21

2.8 Procedures for Acceptance of Design Approvals of Parts … 2-21

2.9 Environmental Testing and Approval Procedures … 2-24

2.9 Environmental Testing and Approval Procedures … 2-24

2.10 Recordkeeping Requirements … 2-27 SECTION III POST DESIGN APPROVAL PROCEDURES

3.0 General … 3-1

3.1 Continued Airworthiness … 3-1

3.2 Design Changes … 3-7

3.3 Approval of Design Data Used in Support of Repairs … 3-11

TABLE OF CONTENTS

TABLE OF CONTENTS

Implementation Procedures ii Revision 1, October 2011

3.4 Design Support for Any Production Approval Based on a Licensing Agreement … 3-16

SECTION IV ADMINISTRATION OF DESIGN APPROVALS

4.0 General … 4-1

4.1 Transfer of Type Certificates/Supplemental Type Certificates … 4-1

4.2 Surrender of a Type Certificate or Supplemental Type Certificate … 4-5

4.3 Revocation or Suspension of a Type Certificate or Supplemental Type Certificate … 4-5

4.3 Revocation or Suspension of a Type Certificate or Supplemental Type Certificate … 4-5

4.4 Surrender or Withdrawal of a TSO or ETSO Design Approval … 4-6

4.5 Change of Ownership of an ETSO Authorisation … 4-6

4.6 Surrender, Withdrawal or Termination of an FAA PMA for a Critical Component … 4-6

SECTION V EXPORT AIRWORTHINESS CERTIFICATION

SECTION V EXPORT AIRWORTHINESS CERTIFICATION

5.0 General … 5-1

5.1 Certifying Statements for Export … 5-1

5.2 Information on Aircraft Noise and Engine Emissions Levels … 5-13

5.3 Coordination of Export Certificate of Airworthiness Exceptions … 5-13

5.4 Coordination of Authorized Release Certificate Exceptions … 5-14

5.5 Additional Requirements for Imported Products … 5-15

5.5 Additional Requirements for Imported Products … 5-15

SECTION VI TECHNICAL ASSISTANCE

6.0 General … 6-1

6.1 Witnessing of Tests During Design Approval … 6-2

6.2 Compliance Determinations … 6-3

6.3 Conformity Certifications During Design Approval … 6-3

6.4 Surveillance and Other Support … 6-4

6.5 Airworthiness Determination … 6-4

6.5 Airworthiness Determination … 6-4

TABLE OF CONTENTS

Implementation Procedures iii Revision 1, October 2011

6.6 Airworthiness Certificates … 6-5

6.7 Handling of Requests for Proprietary Data and Freedom of Information Act (FOIA)/Public Access to Official Documents Information … 6-5

6.6 Airworthiness Certificates … 6-5

6.8 Accident/Incident and Suspected Unapproved Parts Investigation Information Requests … 6-6 SECTION VII FURTHER WORKING ARRANGEMENTS … 7-1

SECTION VIII AUTHORITY … 7-1

APPENDICES APPENDIX A List of Addresses for EASA and FAA … A-1 APPENDIX B FAA and EASA Recognized Standards … B-1 APPENDIX C FAA/EASA Type Validation Principles/Post-Type Validation Principles … C-1 APPENDIX D Acronym List … D-1 APPENDIX E Scope of Acceptance for EU STCs Dated Before September 28, 2003 … E-1 APPENDIX F Management Plan for CFM International SA F-1 APPENDIX G Record of Revisions G-1

TECHNICAL IMPLEMENTATION PROCEDURES FOR AIRWORTHINESS AND ENVIRONMENTAL CERTIFICATION

TECHNICAL IMPLEMENTATION PROCEDURES FOR AIRWORTHINESS AND ENVIRONMENTAL CERTIFICATION

SECTION I GENERAL 1.0 Purpose. The purpose of these technical implementation procedures, (hereafter referred to as Implementation Procedures) entered into pursuant to Article 5 and Annex I of the Agreement between the Government of the United States of America and the European Union on Cooperation in the Regulation of Civil Aviation Safety (“the Agreement”), is to define the interface requirements and activities between the Federal Aviation Administration (FAA), the European Aviation Safety Agency (EASA) and European Union (EU) Member State Aviation Authorities (AAs) for the import, export, and continued support of civil aeronautical products.

Note: Appendix D lists all acronyms used in this document. 1.1 Communications. 1.1.1 Changes in Aircraft Certification Systems.

(a) These Implementation Procedures are based upon sufficiently similar aircraft certification systems being in place at the time of signing. Therefore, the FAA and EASA shall keep each other informed of significant changes within those systems, such as changes in:

(1) statutory responsibilities; (2) organizational structure (e.g., key personnel, management structure,

technical training, office location);

(3) airworthiness and environmental standards and procedures; (4) production quality control system oversight, including system oversight

outside their territory; or (5) delegated or contracted functions or the kinds of organizations to

which functions have been delegated or contracted. (b) Revision by the FAA, EASA or an AA to its regulations, airworthiness codes, policies, procedures, organizational structure, production quality control system

oversight, or delegation system may affect the basis and the scope of these Implementation Procedures. Accordingly, upon notice of such changes by FAA or EASA, FAA or EASA may request a meeting to review the need for amendment to these Implementation Procedures. 1.1.2 Communications. Data and documents exchanged under these Implementation Procedures between the FAA and EASA, and where applicable the FAA and AAs, shall be in the English language. 1.1.3 Technical Consultations. (a) The FAA and EASA shall notify each other of draft guidance material and consult on new appliance performance standards or proposed changes to these standards. (b) The FAA and EASA Certification Directors agree to consult as necessary to provide input when requested on technical issues and resolve technical disagreements. The frequency of these exchanges will depend on the number and significance of the issues to be discussed. 1.1.4 Interpretations and Resolution of Conflicts between FAA and EASA.

(a) In the case of conflicting interpretations by FAA and EASA of the laws, airworthiness or environmental regulations/standards, requirements, or acceptable means of compliance pertaining to certifications, approvals, or acceptance under these Implementation Procedures, the interpretation of the Technical Agent whose law, regulation/standard, requirement, or acceptable means of compliance is being interpreted shall prevail.

(b) The FAA and EASA agree to resolve issues through consultation or any other mutually agreed-upon means. Every effort should be made to resolve issues at the lowest possible level before elevating the issue to higher management.

(c) To resolve conflicts the FAA and EASA shall use the following processes.

(1) For the FAA, when a project manager (PM) and project certification manager (PCM) cannot agree, the first certification decision point is the local office manager, who shall consult with the EASA Certification Manager.

(1) For EASA, when a PCM and PM cannot agree, the first certification decision point is the EASA Certification Manager, who shall consult with the local FAA office manager.

(2) If resolution cannot be reached, the issue shall be expeditiously raised to the Directorate Manager (or Division Manager where applicable), who shall consult with the EASA Head of Products or Head of Organisations, as applicable.

(2) If resolution cannot be reached, the issue shall be expeditiously raised to the EASA Head of Products, or Head of Organisations where applicable, who shall consult with the FAA Directorate/Division Manager.

(3) If resolution cannot be reached, the Directorate/Division Manager shall consult with the Aircraft Certification Service Director as appropriate.

(3) If resolution cannot be reached, the Head of Products/Organisations shall consult with the EASA Certification Director and/or other Directors or the Internal Safety Committee, as appropriate.

(4) The Aircraft Service Director shall resolve the matter or consult with the EASA Certification Director, per paragraph 1.1.3.

(4) The Certification Director shall resolve the matter or consult with the FAA Aircraft Certification Director, per paragraph 1.1.3.

(d) Issues that cannot be satisfactorily resolved between the FAA and EASA Certification Directors, may be raised to the Certification Oversight Board for further consideration. (See Article 2.2 of Annex 1, Airworthiness and Environmental Certification (hereinafter Annex 1).)

(e) Issues that cannot be resolved by the Certification Oversight Board may be forwarded by either FAA or EASA to the Bilateral Oversight Board for resolution.

1.1.5 Communications Regarding Designees and Approved Organizations.

(a) Compliance findings, conformity inspections, test witnessing, and other certification activities in support of an FAA certification program sometimes take place in the territory of the European Union and conversely similar activities in support of an EASA certification program may take place in the territory of the United States. When resources or schedule do not permit the use of technical assistance (see Section VI), designees or representatives of delegated or approved organizations may need to travel to the other’s territory to perform these functions. Unless otherwise agreed for specific projects, the FAA or EASA shall not routinely notify the other of designee or organization activities in advance of designees or representatives of approved organizations traveling to the United

States or to the European Union, to make findings of compliance and/or to perform conformity inspections.

(b) FAA and EASA understand that there may be occasional situations where either may interact directly with an individual designee or approved organization of the other. In such cases it is the responsibility of the initiator of the contact to notify the other as soon as possible. Any such direct communication between FAA or EASA and the other’s designees or organizational representatives should be limited to information exchange. The FAA and EASA shall always consult with one another on significant validation program decisions. 1.1.6 Projects Involving a Separate State of Design and State of Manufacture. The FAA and EASA recognize that some projects of their aviation industries may involve products designed under one party's jurisdiction and manufactured under the other party's jurisdiction.

In such cases, the FAA, EASA and, as appropriate the AA, shall work together to develop a working arrangement defining their respective responsibilities to ensure that the relevant functions applicable to the State of Design and State of Manufacture under Annex 8 of the 1944 Convention on International Civil Aviation done at Chicago (“Chicago Convention”) adopted by the International Civil Aviation Organization (ICAO) are carried out. Such working arrangements shall address the continued airworthiness responsibilities applicable to the State of Design and the State of Manufacture and shall be documented in accordance with Section VII of these Implementation Procedures. 1.2 Reserved. 1.3 Certification Oversight Board Procedures. 1.3.1 Meetings. The Certification Oversight Board under the leadership of the FAA and EASA’s Certification Directors shall meet annually to review progress on implementation of these Implementation Procedures. The meetings will rotate between the U.S. and Europe with one meeting hosted by FAA and the next by EASA, unless otherwise agreed.

When necessary and by mutual agreement additional meetings may be held and can be face to face, videoconference or by teleconference.

(a) Each annual meeting shall provide an open session for public/industry participation. (b) Meeting attendees shall include the offices responsible for administration and technical implementation of these Implementation Procedures and additional officials as needed to address the meeting agenda items. At the discretion of the co-chairs, other staff and representatives of appropriate organizations may be invited to participate.

(c) The host is responsible for meeting minutes and action items, which are tracked. (d) The Certification Oversight Board 1) may report any unresolved issues to the Bilateral Oversight Board, and 2) shall report the status of the implementation of any decisions of the Bilateral Oversight Board, on request.

1.3.2 Taskings/Subgroups. The Certification Oversight Board may charter subteams to address specific technical issues and make recommendations to the Certification Oversight Board. 1.3.3 Cooperation in Quality Assurance and Standardization Activities. In order to promote continued understanding and compatibility in each other’s certification systems, FAA and EASA shall consult and share information on quality assurance and standardization-accreditation activities. For this purpose, FAA and EASA focal points shall meet and communicate on a regular basis to agree upon an annual schedule of joint activities including mutual attendance as an observer in each other’s future activities, and to discuss significant audit findings and reports as a result of these activities. The record of such meetings and recommendations, with appropriate supporting materials, shall be submitted to the Certification Oversight Board.

1.3.4 Procedures for Adding and Suspending the Acceptance of Findings and Approvals Made by Specific Aviation Authorities. (a) EASA shall notify the FAA of a proposed addition of the acceptance of production and/or airworthiness findings or approvals made by an AA, as defined in the Appendix to Annex 1. EASA and the FAA shall consult on the basis for this proposal. EASA shall provide the opportunity for FAA’s participation in its standardization audit or the FAA and EASA shall conduct a joint assessment. In exceptional cases, if a joint assessment is not practical and EASA cannot change its plans to accommodate FAA’s participation, the FAA shall conduct its own assessment of the AA, with an EASA observer. The FAA, following the applicable assessment, shall inform EASA of concurrence or non-concurrence with EASA’s recommendation. If the FAA concurs with a recommendation to accept production and/or airworthiness findings or approvals, the Certification Oversight Board shall make a recommendation to the Bilateral Oversight Board to revise the Appendix to Annex 1, accordingly, or otherwise report its disagreement. (b) In the case of the proposed suspension of the acceptance of findings made by an AA, EASA or the FAA shall promptly notify the other and consult. If EASA has made the decision to suspend acceptance of production and/or airworthiness findings or approvals, a recommendation shall be made to the Bilateral Oversight

Board to revise the Appendix to Annex 1. If the FAA makes the proposal to suspend the acceptance of findings or approvals, then a possible joint confidence building activity may be undertaken. If confidence is not restored, through whatever means, the Certification Oversight Board shall notify the Bilateral Oversight Board requesting that the Appendix to Annex 1 be revised accordingly.

1.3.5 Amendments and Points of Contact.

(a) These Implementation Procedures may be amended based on a decision of the Certification Oversight Board. Such amendments shall be made effective by signature of the duly authorized representatives of the FAA and EASA. Administrative/editorial changes to these procedures may be made by the focal points after mutual consultation.

(b) The focal points for the implementation of these Implementation Procedures are listed in Appendix A. (c) EASA shall maintain and make available to the FAA a list of AA contacts for production and export airworthiness certification.

1.4 Applicable Requirements, Procedures, and Guidance Material.

1.4.1 The U.S. requirements for aircraft airworthiness and environmental certification are contained in the United States Code of Federal Regulations (CFR), Title 14, Parts 21, 23, 25, 26, 27, 29, 31, 33, 34, 35, and 36. Additional requirements are in Parts 43 and 45. The FAA also uses European certification specification (CS)-22 and CS-VLA for some special class aircraft. Appliance performance standards are contained in FAA Technical Standard Orders (TSO). Guidance material, policy, and procedures are contained in FAA Advisory Circulars, Orders, Notices, and Policy Memoranda. 1.4.2 The European Union requirements for aircraft airworthiness and environmental certification are contained in the European Union regulation (EC) No 216/2008 of the European Parliament and of the Council of 15 July 2002, Commission Regulation EC 1702/2003, (hereafter referred to as EASA Part 21), and EASA Certification Specifications, Acceptable Means of Compliance (AMC), and Guidance Material. 1.5 Entry into Force and Termination. These Implementation Procedures shall enter into force upon signature and shall remain in force until terminated by either Technical Agent. Either the FAA or EASA may terminate these Implementation Procedures upon sixty days written notice to the other Technical Agent.

Termination shall not affect the validity of activity conducted under these Implementation Procedures prior to termination. 1.6. Definitions. For the purpose of these Implementation Procedures, the following definitions apply, in addition to those definitions found in Article 1 of the Agreement.

(a) “Acoustical Change” means any voluntary change in the type design of an aircraft to be FAA-approved that may increase the noise levels of that aircraft (regardless of its classification of major or minor per 14 CFR §21.93(a)). (Ref. 14 CFR §21.93(b)) (b) “Airworthiness Standards” means regulations, airworthiness codes or other certification specifications governing the design and performance of civil aeronautical products, parts, and appliances. (c) “Article” means a material, part, component, process, or appliance. (d) “Appliance” means any instrument, equipment, mechanism, part, apparatus, appurtenance or accessory, including communications equipment, that is used or intended to be used in operating or controlling an aircraft in flight, and is installed in or attached to the aircraft. (e) “Approved Manuals” means manuals, or sections of manuals, requiring approval by the FAA or EASA as part of a certification program.

These include the approved sections of the Flight Manual, the airworthiness limitation section of the Instructions for Continued Airworthiness (ICA), the structural repair manual, the engine and propeller installation and operating instruction manuals, and the certification maintenance requirements, where applicable. (f) “Basic Supplemental Type Certificate (Basic STC)” means a Supplemental Type Certificate whose validation does not require Validating Authority (VA) technical involvement. (g) “Certificating Authority (CA)” means the FAA for design approvals that are U.S. State of Design; EASA when exercising State of Design functions for design approvals in the EU. (h) “Compliance Determination” means the determination, by either the CA’s system or the VA’s system, that the applicant has demonstrated compliance with identified, individual airworthiness standards. (i) “Critical Component” means a part identified as critical by the design approval holder during the product type validation process, or otherwise by the

exporting authority. Typically, such components include parts for which a replacement time, inspection interval, or related procedure is specified in the Airworthiness Limitations section or certification maintenance requirements of the manufacturer’s maintenance manual or Instructions for Continued Airworthiness. (j) “Deviation” is a grant of relief from the requirements of a certification specification when processed through the appropriate regulatory procedure by EASA. (k) “Emissions Change” means any voluntary change in the type design of an airplane or engine to be FAA-approved that may increase fuel venting or exhaust emissions.

(Ref. 14 CFR §21.93(c)). (l) “Environmental Standards” means regulations or certification specifications governing the certification of designs with regard to noise characteristics and exhaust emissions of civil aeronautical products and appliances. (m) “Equivalent Level of Safety Finding” means a finding that alternative action taken provides a level of safety equal to that provided by the airworthiness standards for which equivalency is being sought. (n) “Exemption” means a grant of relief from requirements of a current regulation when processed through the appropriate regulatory procedure by the FAA or the European Commission or AA, as applicable. (o) “Export” means the process by which a product, part or appliance is released from one regulatory system for subsequent use by another country. (p) “Exporting Civil Airworthiness Authority” means the organization within the exporting State charged by the laws of the exporting State, to regulate the airworthiness and environmental certification, approval, or acceptance of civil aeronautical products, parts, and appliances.

The exporting civil airworthiness authority will be referred to herein as the exporting authority. For the United States of America, this exporting authority is the FAA. For the European Union, this is:

(1) EASA, for: (i) the functions and tasks of the State of Design, Manufacture or Registry when related to design approval; and (ii) the approval of certain production organisations and their export airworthiness approvals. (2) the AA, for: (i) the approval of production organisations within their State; (ii) the issuance of corresponding Certificate of Airworthiness; and

(iii) export airworthiness approvals. (q) “Finding” means a final determination of compliance/non-compliance from FAA’s or EASA’s system as a result of a review, investigation, inspection, test, and/or analysis. (r) “Generic Validation Item” means a certification item identified by the VA for particular scrutiny in all products of a certain class. The VA will publish and periodically update Generic Validation Item lists that will be publicly available. (s) “Import” means the process by which an exported product, part, or appliance is accepted by a country’s civil airworthiness authority, or EASA on behalf of an EU Member State, for use and is subsequently placed under that authority’s regulatory system. (t) “Importing Civil Airworthiness Authority” means the organization within the importing State charged by the laws of the importing State with regulating the airworthiness and environmental certification, approval, or acceptance of civil aeronautical products, parts, and appliances. The importing civil airworthiness authority will be referred to herein as the importing authority. For the United States of America, this importing authority is the FAA. For the European Union, this is: (1) EASA for the functions and tasks related to design approval; (2) the AA for all other issues related to the import of a product, part or

appliance. (u) “Licensing Agreement” means a commercial contract between a Type Certificate (TC) or Supplemental Type Certificate (STC) holder and a production organization approval holder (or applicant) formalizing the rights and duties of both parties to use the design data for the purpose of manufacturing the product or part. (v) “Manufacturer” means a person who, by FAA or European Union regulation, is responsible for determining that all products, parts, or appliances produced within their quality control system conform to an FAA or EASA -approved design or established government or industry standard and are in a condition for safe operation. For the European Union this includes a production organisation. (w) “New Aircraft” means an aircraft that is still owned by the manufacturer, distributor, or dealer, if there is no intervening private owner, lease, or time-sharing arrangement, and the aircraft has not been used in any pilot school and/or other commercial operation.

(x) “Non-Basic Supplemental Type Certificate (Non-Basic STC)” means a Supplemental Type Certificate whose validation may require VA technical involvement. (y) “Non-Significant Standards Difference (Non-SSD)” means a VA airworthiness standard that has no CA equivalent, yet it does not result in a difference that is classified by the VA as significant. (z) “Person” means an individual, firm, partnership, corporation, company, association, joint stock association, or governmental entity, and includes a trustee, receiver, assignee, or other similar representative of any of them. (aa) “Product” means a civil aircraft, aircraft engine, or aircraft propeller. (bb) “Production Quality System” means a systematic process which meets the requirements of the exporting authority and ensures that products, parts, and appliances will conform to the approved design and will be in a condition for safe operation. (cc) “Project Validation Item” means a certification item that is unique to a particular validation project, for example, unique design, usage, or Method of Compliance (MOC).

A Project Validation Item is established solely to address that uniqueness. (dd) “Rebuilt Engine” means a U.S. engine that has been disassembled, cleaned, inspected, repaired, as necessary, reassembled, and tested in accordance with 14 CFR Part 43. (ee) “Significant Standards Difference (SSD)” means a VA airworthiness standard that has no CA equivalent, which results in a difference that may require type design changes, approved manual changes, or the imposition of operational limitations to meet the VA standards. The type design or operation approved by the VA could then differ from the design and/or operation approved by the CA. (ff) “Special Condition” means (1) to the FAA: an additional airworthiness standard prescribed by the FAA when the airworthiness standards for the category of product do not contain adequate or appropriate safety requirement due to novel or unusual design features. Special Conditions contain such safety standards as the FAA finds necessary to establish a level of safety equivalent to that established in the applicable regulations.

(2) to EASA: an additional detailed technical specification prescribed by EASA when the airworthiness code for the category of product does not contain adequate or appropriate safety standards due to novel or unusual design features, unconventional use of the product, or experience in service with similar products showing that unsafe conditions may develop. Special Conditions contain such detailed technical specifications as the European Union finds necessary to establish a level of safety equivalent to that intended in the applicable airworthiness code. (gg) “Standards Equivalencies” means the FAA and EASA airworthiness standards that are determined to be equivalent despite their language differences. (hh) “Standard Part” means a part that is manufactured in accordance with an established government or industry-accepted specification, which includes design, manufacturing, and uniform identification requirements.

The specification must include all information necessary to produce and conform the part, and must be published so that any person or organization may manufacture the part. (ii) “Supplier” means a person or organization (at any tier) contracted to furnish aviation products, parts, appliances, components, material or services. (jji) “Used Aircraft” means each aircraft that is not a new aircraft, as defined in paragraph (v) above. (kk) “Validation” means the importing authority’s approval process of a design certificated by either the FAA or EASA. (ll) “Validating Authority (VA)” means the FAA for import into the U.S.; EASA for import into the European Union. (mm) “Validating Authority Certification Basis” means the applicable airworthiness standards identified by the VA plus any exemptions, deviations, special conditions, and equivalent level of safety findings declared by the VA to establish its design acceptance of an imported product or to certify the design change. (oo) “Validation Item (VI)” means a certification item or airworthiness standard of particular interest to the VA.

There are three types of VI: a SSD, a Project Validation Item, and a Generic Validation Item.

SECTION II DESIGN APPROVAL PROCEDURES 2.0 General.

2.0.1 The FAA and EASA shall use these procedures for the initial design approval of each other’s products and appliances. 2.0.2 The FAA and EASA shall use the validation process based on the Type Validation Principles, which are defined in Appendix C, when certificating each other’s products and issuing STCs. 2.0.3 FAA and EASA shall also use a simplified validation process when issuing an appliance approval. (See paragraph 2.5) 2.0.4 EASA shall use the validation process defined in paragraph 2.8 when accepting FAA-approved critical Parts Manufacturer Approval (PMA) parts. 2.0.5 In accordance with Article 16.C of the Agreement, the FAA and EASA shall continue to recognize and accept design approvals and data certified by FAA, EASA, and AAs, and validated by FAA, EASA or an AA prior to the date of these Implementation Procedures under the bilateral aviation safety agreements and bilateral airworthiness agreements listed in Attachment 1 of the Agreement until such approvals are replaced or cancelled.

These design approvals include TCs, amended TCs, STCs, Letters of TSO Design Approval, European Technical Standard Order/Joint Technical Standard Order (ETSO/JTSO) Authorisations or national appliance approvals, and FAA Parts Manufacturer Approval (PMA) parts. 2.0.6 Assigning Compliance Determinations. The VA’s design approval shall be based on the CA system’s technical evaluations, tests, inspections, and compliance determinations to the maximum extent practicable. The VA is expected, with only a few exceptions, to assign determinations of compliance to its requirements to the CA system. Nevertheless, the VA must maintain a general awareness and understanding of the CA’s compliance activities to be able to exercise its responsibilities as a State of Registry. The VA is able to make findings of compliance, without further showing, based upon the CA’s statements of compliance. 2.0.7 Communications During a Validation Project. Validation requires effective communication between the FAA, EASA, and the applicant. Communication should occur authority-to-authority.

The expectation is that there will be an early exchange of information and discussion between the certificating and validating authorities. Continued communication between the CA and VA is necessary in order for the VA to adequately understand actions taken by the CA and applicant.

2.0.8 Project Prioritization. The FAA does not normally issue a design approval for a product manufactured outside the United States unless it is to be imported, i.e., an aircraft to be U.S.-registered or an engine, propeller, appliance or part to be incorporated into the design of a U.S.-registered aircraft or U.S.-manufactured product. Union applicants for U.S. design approval should provide the FAA with evidence of import. EASA will adopt a similar project prioritization approach for applications from U.S. applicants under this agreement. 2.0.9 Validation Applications.

2.0.9.1 Applications for FAA or EASA approval are intended for civil aeronautical products and appliances. Products and appliances which are intended only for military, customs, police, search and rescue, firefighting, coastguard or similar activities or services are not eligible for FAA or EASA validation under this agreement unless the CA has accepted to certify the product or appliance and there is 1) a civilian use/application by a civilian customer within the jurisdiction of the importing authority or 2) a contract with the VA for its approval of the product or appliance, i.e. a contract between FAA and the U.S. military or a contract between the U.S. applicant and EASA. In these cases, the FAA and EASA shall consult to determine whether validation is within the scope of the Agreement or requires a Special Arrangement under Section VII.

2.0.9.2 Applications for FAA Design Approval.

(a) All applications for FAA design approval from applicants in the European Union shall follow the following procedure.

(1) The applicant shall:

(i) Complete the FAA form appropriate to the design approval requested (i.e., FAA Form 8110-12 or via letter) and, (ii) Forward the FAA form plus the applicable technical data package (See paragraphs 2.1.1, 2.2.2, and 2.5.1) to EASA.

2.0.9.3 Applications for EASA Design Approval.

(a) All applications for EASA design approval from applicants in the United States shall follow the following procedure.

(1) The applicant shall:

(i) Complete the EASA form appropriate to the design approval requested (see EASA website) and,

(ii) Forward the EASA form for each individual design approval to the FAA plus the applicable technical data package (See paragraphs 2.1.2, 2.2.3, and 2.5.2).

(2) EASA shall:

(i) Review the application package to determine if it is within the scope of these Implementation Procedures. (ii) Forward the application plus the applicable data along with an EASA cover letter to the appropriate FAA office (See Appendix A). Where electronic data is submitted, it must be in a format that is compatible with FAA’s information systems and there must be an arrangement between the applicant and the EASA under paragraph 2.10.2.

(2) The FAA shall:

(i) Review the application package to determine if it is within the scope of these Implementation Procedures.

(ii) Forward the application plus the applicable data along with an FAA cover letter to EASA via email. (See Appendix A or EASA website for applicable EASA office). Where electronic data is submitted, it must be in a format that is compatible with EASA’s information systems and there must be an arrangement between the applicant and the FAA under paragraph 2.10.1.

(3) Upon receipt of the FAA cover letter and application form, EASA shall:

(i) Notify the applicant of acceptance and identify a technical focal point contact for further communication.

(ii) Notify the applicant of EASA fees.

(4) To proceed with the project, the applicant must:

(i) Comply with the EASA Fees and Charges Regulation.

2.1 Design Approval Procedures for Type Certificates. 2.1.1 Application Package for FAA Type Certification.

(a) An application for an FAA Type Certificate from an applicant in the European Union may be submitted for products with an EASA Type Certificate, or for products where application for type certification has been made to EASA.

(b) EASA should ensure that the applicant’s technical data package contains the following information:

(1) Data defined in 14 CFR §21.15;

(2) EASA TC and TC Data Sheet, if available, and a definition of the airworthiness and environmental standards upon which EASA design approval was (or is to be) based, and the amendment level of the U.S. airworthiness and environmental standards that the applicant proposes and EASA believes to be equivalent to its own standards;

(3) Date of application to EASA; and

(4) The applicant’s requested date for FAA type certification.

(c) Also, the application should contain the following, if known at the time of application:

2.1.2 Application Package for EASA Type Certification.

(a) An application for EASA Type Certificate from an applicant in the United States may be submitted for products with an FAA Type Certificate, or for products where application for type certification has been made to the FAA.

(b) FAA should ensure that the applicant’s technical data package contains the following information:

(1) Data defined in EASA Part 21A.15;

(2) The FAA TC and TC Data Sheet, if available, and a definition of the airworthiness and environmental standards upon which the FAA design approval was (or is to be) based, and the amendment level of EASA airworthiness and environmental standards that the applicant proposes and the FAA believes to be equivalent to its own standards;

(3) Date of application to the FAA; and (4) The applicant’s requested date for EASA type certification.

(c) Also, the application should contain the following, if known at the time of application:

(1) A description of all novel or unusual design features known to

(1) A description of all novel or unusual design features known to the applicant or EASA at the time of application which might necessitate issuance of FAA special conditions under 14 CFR §21.16, or which might require a special review of acceptable means of compliance; and

(2) All known or expected deviations or equivalent level of safety findings relative to EASA’s standards for design approval that might affect compliance with the applicable U.S. airworthiness and environmental standards.

(3) The information necessary to complete FAA Form 8110-23, 8110-24 or 8110-27, as appropriate in accordance with FAA Order 8110.35, for the Aircraft Noise Certification Historical Database. (4) Available information on U.S. market potential, including specific customers, delivery schedule, and U.S. content (e.g. major components) of the product.

(d) If the application is incomplete, the FAA shall notify EASA within 10 working days and return the application in 30 days if the necessary information is not provided.

the applicant or FAA at the time of application which might necessitate issuance of EASA special conditions under EASA Part 21A.16B, or which might require a special review of acceptable means of compliance; and

(2) All known or expected exemptions or equivalent level of safety findings relative to the FAA’s national standards for design approval that might affect compliance with the applicable EASA airworthiness and environmental standards.

(3) The information necessary to complete the EASA type-certificate data sheet for noise and for the databases of EASA approved noise levels. (4) Available information on specific EU customers, delivery schedule, and EU content (e.g. major components) of the product.

(d) If the application is incomplete, EASA shall notify the FAA within 10 working days and return the application in 30 days if the necessary information is not provided.

2.1.3 Establishment of the FAA or EASA Type Certification Basis.

2.1.3.1 FAA Type Certification Basis.

(a) The FAA shall develop its type certification basis using the applicable airworthiness standards (14 CFR) in effect on the date application was made to EASA, or where applicable an AA, for its type certificate. (When 14 CFR part 26 applies to a European transport category airplane, the applicable standard is the amendment in effect on the date the FAA type certificate is issued.) (b) The applicable airworthiness requirements may be supplemented with the following additional requirements:

(1) Special conditions: The FAA shall review all novel and unusual design features for development of special conditions.

(2) Technical requirements necessary in the interest of safety: These include requirements to preclude a potential unsafe condition finding for the product under 14 CFR §21.21(b)(2). These may be generated as a result of adverse service history of this product, or other products of a similar nature or design. This includes, but is not limited to, actions taken by EASA to correct unsafe conditions.

(c) Applicants for U.S. type

2.1.3.2 EASA Type Certification Basis. (a) EASA shall develop its type certification basis using the applicable airworthiness codes in effect on the date application was made to the FAA for its type certificate. The applicable airworthiness requirements may be supplemented with the following additional requirements:

(1) Special conditions: For the development of special conditions, EASA shall review:

(i) All novel or unusual design features,

(ii) The intended use of the product,

(iii) Its service history, and

(iv) the experience from other similar products in service or products having similar design features, having shown that unsafe conditions may develop.

(b) Applicants must also comply with the applicable noise, fuel venting, and exhaust emission standards, as defined in EASA Part 21, that are in effect on the date of application for type certification to EASA.

certificate must also comply with the applicable fuel venting and exhaust emission standards of 14 CFR Part 34 and the noise standards of 14 CFR Part 36 in effect on the date of application to the FAA for type certification. 2.1.4 FAA and EASA Validation Process.

(a) After receipt of an application, the FAA or EASA shall conduct certification activities under the “Type Validation Principles” (See Appendix C). These principles recognize that the VA has sovereign authority over the certification process and compliance findings within its jurisdiction. The principles do not diminish the VA’s responsibilities or future right to type design information; they define how the VA's rights shall be routinely exercised. In particular, the VA must have ready access to information necessary to carry out its continued airworthiness responsibilities. If there are overwhelming reasons to go outside these defined principles, such reasons shall be technically explained by the VA in every instance.

(b) When the CA, VA and the TC applicant agree to use a joint certification/validation process per Article 3.2.6 of Annex 1, they shall:

(1) Document their agreement, including resource commitments.

(2) Establish a delegation and work sharing program between the CA and VA via a working arrangement (See Section VII) to cover both TC and post- TC activities.

(c) The TC applicant is responsible for communicating with and obtaining the agreement of all suppliers including those under the jurisdiction of the VA.

(d) To implement this validation process, the FAA shall employ its internal procedures as defined in FAA Order 8110.52, Type Validation and Post-Type Validation Procedures. EASA shall use Appendix C of these Implementation Procedures as its internal procedures.

2.1.5 Issuance of the Type Certificate.

2.1.5.1 Issuance of U.S. Type Certificate. The FAA shall issue a TC for an EU

2.1.5.2 Issuance of a European Type Certificate. EASA shall issue a TC (or where applicable a Restricted

product when:

(a) The applicant has demonstrated compliance to the U.S. type certification basis, and (b) EASA has issued a statement of compliance to the U.S. type certification basis, and (c) EASA has issued an EASA TC for the product.

Type Certificate (RTC)) for a U.S. product when: (a) The applicant has demonstrated and declared compliance to the European type certification basis, and

(b) FAA has issued a statement of compliance to the European type certification basis, and (c) FAA has issued an FAA TC for the product.

2.1.6 Design Approval Procedures for Type Certificates that Have Received an EASA Restricted Type Certificate (RTC). For EU aircraft which have been or shall be granted an EASA RTC, the FAA may agree to validate such aircraft designs on a case-by-case basis. In these cases, the FAA and EASA agree to follow the validation procedures in paragraph 2.1 for TCs.

2.2 Design Approval Procedures for Supplemental Type Certificates (STCs).

2.2.1 Scope of FAA STC Application Acceptance. The FAA may accept applications for STCs for: (a) All STCs (Basic and Non-Basic) issued after 28 September 2003 when the original STC application is made to EASA:

(1) On U.S. State of Design products,

(2) On products for which EASA acts on behalf of the State of Design, and

(3) On third country aircraft which have been type certificated by both the FAA and

EASA. (b) All STCs (Basic and Non-Basic), issued before 28 September 2003, in accordance with the scope defined in Appendix E, from applicants in France, Germany, Italy, Netherlands, Sweden and the United Kingdom.

2.2.2 Application Package for a U.S. STC.

(a) As provided above in paragraph 2.2.1, U.S. STCs may be issued under the provisions of 14 CFR §21.117 and §21.29 for approval of EASA-approved major changes to the type design of an aircraft, engine, or propeller if:

(1) The FAA has certificated/validated the product, and

(2) EASA is acting on behalf of the State of Design for the design change, and

(3) EASA has issued an EASA STC.

2.2.3 Application Package for an EASA STC.

(a) EASA STCs may be issued for approval of FAA-approved major design changes to a type design of an aircraft, aircraft engine, or propeller regardless of the product’s State of Design if:

(1) EASA has certificated/validated the product, and (2) the FAA is the authority of the State of Design for the design change, and (3) the FAA has issued an STC.

(b) A European Union applicant for a U.S. STC should send the application to EASA and request that the application and required information be forwarded to the New York Aircraft Certification Office (ACO). (See Appendix A.)

(b) In cases where a critical part has been approved under FAA PMA (see paragraph 2.8.2) without a corresponding FAA STC, EASA will also issue an STC.

(c) EASA should ensure that each application contains the following information:

(1) A description of the change, together with the make and model of the product; (2) The classification as Basic or Non Basic STC, as explained in Appendix C, paragraph 6;

(c) A U.S. applicant for an EASA STC should send the application to the FAA and request that the application and required information be forwarded to EASA, as listed in Appendix A.

(d) This STC application shall be made in accordance with EASA Part 21.113(a), and include the information to fulfill Part 21.113(b) regarding a link to the TC holder. FAA should ensure that each application contains the following information:

(3) A copy of the EASA STC and certification basis; (4) The applicant’s requested date for FAA issuance of the STC; (5) A description of all novel or unusual design features which might necessitate issuance of FAA special conditions;

(6) All deviations or equivalent level of safety findings granted by EASA for the STC; (7) A statement as to the effect of the STC on the changed product’s noise and/or emissions levels, and (d) In addition, the applicant should provide available information on U.S. market potential, including specific customers and delivery schedule.

(e) If the application is incomplete, the FAA shall notify EASA within 10 working days and return the application in 30 days if the necessary information is not provided. (f) The FAA may accept applications for concurrent STC certification/validation, in which case the information specified in paragraphs 2.2.2(c) may not be available.

(1) A description of the change, together with the make and model of the product; (2) The classification as Basic or Non Basic STC, as explained in Appendix C, paragraph 6; (3) A copy of the FAA STC and certification basis; (4) The applicant’s requested date for EASA issuance of the STC; (5) A description of all novel or unusual design features which might necessitate issuance of EASA special conditions; (6) All exemptions or equivalent level of safety findings granted by the FAA for the U.S. STC.; (7) A statement as to the effect of the STC on the changed product’s noise and/or emissions levels, and (e) In addition, the applicant should provide available information on EU market potential, including specific customers and delivery schedule.

(f) In cases where the STC applicant has not entered into an arrangement with the TC holder, the FAA shall review and confirm the applicant’s justification that an arrangement is not necessary. The applicant’s justification and the FAA concurrence statement shall be provided to EASA.

(g) If the application is incomplete, EASA shall notify the FAA within 10

working days and return the application in 30 days if the necessary information is not provided. (h) EASA may accept applications for concurrent STC certification/validation, in which case the information specified in paragraphs 2.2.3(d) may not be available.

2.2.4 Establishing the FAA or EASA STC Certification Basis.

2.2.4.1 Establishing the FAA STC Certification Basis.

(a) The FAA shall develop the STC certification basis, including the environmental requirements, in accordance with FAA Order 8110.4, Type Certification, and 14 CFR §21.115 in a manner that is consistent with the criteria that is used to establish the certification basis for a domestic STC of similar design and service history. The date of application is the date application is made to EASA, or where applicable under prior Bilateral Aviation Safety Agreements to an AA, for the STC. (b) In the case of an STC involving an acoustical change, compliance must be shown with the applicable noise requirements of 14 CFR Part 36 in effect on the date of application to the FAA for the STC. In the case of an emissions change, compliance must be shown with the applicable fuel venting and exhaust emissions requirements of 14 CFR Part 34.

2.2.4.2 Establishing the EASA STC Certification Basis.

(a) The EASA shall develop the STC certification basis in accordance with EASA Internal Working Procedures Supplemental Type Certification (STCP) and EASA Part 21A.101 in a manner that is consistent with the criteria that is used to establish the certification basis for a domestic STC of similar design and service history. The date of application is the date application is made to FAA for the STC. (b) Applicants must also comply with the applicable noise, fuel venting, and exhaust emissions standards as defined in EASA Part 21, that are in effect on the date of application for STC to the EASA.

2.2.5 FAA and EASA Validation Process for STCs.

(a) After receipt of an application, the FAA or EASA shall conduct certification activities under the “Type Validation Principles” (See Appendix C).

(b) The following documentation shall be required for review, as applicable, during the STC approval process:

(1) Compliance Checklist, (2) Airplane/Rotorcraft Flight Manual Supplement, (3) Master Documentation List/Master Drawing List, (4) Manufacturing and Installation Instruction Drawings, (5) Maintenance/Repair Manual Supplements, (6) Weight and Balance data, (7) Instructions for Continued Airworthiness, and (8) Documentation concerning the effect of the STC on the changed product’s noise and/or emissions levels.

2.2.6 Issuance of the STC. 2.2.6.1 The FAA shall issue an STC when compliance with the applicable U.S. airworthiness and environmental certification requirements has been verified, EASA has made a compliance statement to FAA’s certification basis, and EASA has issued its STC.

2.2.6.2 EASA shall issue an STC when compliance with the applicable EASA airworthiness and environmental certification requirements has been verified, the FAA has made a compliance statement to EASA’s certification basis, and the FAA has issued its STC.

2.3 Procedures for Approval of Manuals, including Flight Manuals.

(a) Initial Approval of Manuals. Approved Manuals including initial STC supplements must be submitted to the VA for review and approval. Following VA notification of its approval, the CA shall sign the Approved Manual(s) on behalf of the VA.

(b) Revisions to Approved Manuals. The FAA and EASA may authorize the review and signature of revisions to flight manuals and other Approved Manuals, supplements, and appendices on behalf of each other as follows, in order to facilitate their timely approval:

(i) The CA shall notify the VA of changes to the existing approved VA limitations, performance, weight and balance, or procedures of Approved Manuals, and changes to any parts of the Approved Manuals for which the VA retained the compliance determination during its validation. The VA shall review the changes, notify its approval, and may authorize signature on its behalf to the CA. The VA and the CA may agree to notify fewer changes on an individual certificate holder basis.

(ii) The CA shall review editorial, administrative, and other minor changes on behalf of the VA, and shall ensure that those changes meet the VA's requirements. Such revisions shall be submitted promptly for the VA’s record, but the VA may authorize the CA to sign such revisions on behalf of the VA without prior notification. 2.4 Evaluation of Operational and Maintenance Aspects.

2.4.1 FAA Evaluation of Aircraft Operational and Maintenance Aspects.

(a) The FAA has established Aircraft Evaluation Groups (AEG), located at the product accountable Directorates. The AEGs are responsible for the operational and maintenance aspects of the type certification/supplemental type certification process.

(b) The AEG shall conduct Boards, as appropriate, to review the following items on EU products

2.4.2 EASA Evaluation of Aircraft Operational and Maintenance Aspects.

(a) EASA does not yet have implementing rules relating to operational aspects, so Operational Evaluations are carried out using interim procedures under a Operations Evaluation Board (OEB). The Flight Standards Department in the EASA Certification Directorate is responsible for managing this process on behalf of EU Member States. (b) The OEB shall review the following items at the request of the

prior to their entry into U.S. operations: operational configuration; pilot training and licensing requirements; and the formulation and approval of a Master Minimum Equipment List (MMEL). The AEG shall be invited to participate in the familiarization meeting by the FAA Project Manager, and shall identify items for inclusion in issue papers as appropriate to the type design. Compliance with AEG requirements is not required at the time of the issuance of the U.S. TC/STC, but to avoid operational suitability problems, applicants are encouraged to complete AEG requirements early in the project.

manufacturer: operational suitability; pilot training and licensing requirements; and the review and recommendation for approval by the AAs of a Master Minimum Equipment List (MMEL). The OEB chairman shall identify items for inclusion in Operation Review Item papers as appropriate to the applicant. The formation of a OEB is not required, but it is encouraged to run the process in tandem with the type certification process to avoid operational suitability issues and provide a European standard for the areas covered.

2.4.3 The FAA and EASA shall accept a Maintenance Review Board (MRB) Report and associated Instructions for Continued Airworthiness documentation when developed jointly. Changes to this documentation may also be addressed jointly. In the absence of a joint MRB, the FAA AEG shall conduct its own MRB or equivalent process to develop acceptable ICA in accordance with FAA Order 8110.54 and communicate changes. Similarly, in the absence of a joint MRB, EASA shall conduct its own MRB or equivalent process to develop acceptable ICA and communicate changes.

2.5 Design Approval Procedures for Technical Standard Order (TSO) and European Technical Standard Order (ETSO) Design Approval.

2.5.1 Design Approval Procedures for FAA Letters of TSO Design Approval.

(a) Application.

(1) A European Union applicant for an FAA Letter of TSO Design Approval shall make application through EASA with a request that the application and required

2.5.2 Design Approval Procedures for ETSO Authorisation (except Auxiliary Power Units (APUs)).

(a) Application.

(1) A U.S. applicant for an ETSO Authorisation is required to make an application through the responsible FAA ACO with a request that the application and required information be

information be forwarded to the FAA Boston Aircraft Certification Office, at the address indicated in Appendix A. (2) EASA should check to see that the applicant has used the FAA technical policy and procedures related to the latest FAA TSO performance standard. EASA shall not forward applications that have not used the latest standards. (3) EASA must ensure that the application package includes the following:

(i) All the required data/documentation as specified in the FAA TSO performance standard;

(ii) If applicable, request to deviate from the FAA TSO standard (including any EASA-approved equivalencies) and substantiation data for FAA approval, or identification of the deviation and evidence of FAA approval (if request was made in advance of application);

(iii) Statement of conformance to the FAA TSO performance standard from the applicant;

(iv) Certifying statement from EASA indicating that the appliance has been examined, tested, and

forwarded to EASA, at the address indicated in Appendix A.

Note: A U.S. holder of FAA TSOA under FAA TSO-C148 fasteners, FAA TSO-C149 bearings, and FAA TSO-C150 seals should not apply for ETSO Authorisation. EASA considers such parts to be standard parts.

(2) FAA should check to see that the applicant has used the EASA technical policy and procedures related to the latest ETSO performance standard. FAA shall not forward applications that have not used the latest standards.

(3) FAA must ensure that the application package includes the following:

(i) EASA Application Form 34, Declaration of Design and Performance (DDP) and all the required data/documentation as specified in the ETSO performance standard.

(ii) If applicable, request to deviate from the ETSO standard (including any FAA-approved equivalencies) and substantiation data for EASA approval, or identification of the deviation and evidence of EASA approval (if request

found to meet the applicable FAA TSO or other standards found by the FAA to provide an equivalent level of safety; and

(v) Copy of the EASA ETSO Authorisation or equivalent European approval issued by an EU Member State prior to September 2003.

(4) Also, the application should contain the following, if known at the time of application:

(i) Evidence that the appliance will be imported into the U.S., installed on a U.S.–registered aircraft, or installed on a U.S.– manufactured product.

(ii) The evidence must identify the FAA TSO appliance model at a minimum. The evidence provided must also be valid at the time of application in order for the project to be worked promptly.

(5) If the application is incomplete, the FAA shall notify EASA within 10 working days and return the application in 30 days if the necessary information is not provided.

(6) In a case where there is no ETSO standard, but EASA has approved an appliance using an

was made in advance of application);

(iii) Statement of conformance to the ETSO performance standard from the applicant, using the EASA Form 35;

(iv) Certifying statement from FAA indicating that the appliance has been examined, tested, and found to meet the applicable EASA ETSO or other standards found by EASA to provide an equivalent level of safety; and

(v) Copy of the FAA TSO Authorisation.

(4) Also, the application should contain the following, if known at the time of application:

(i) Evidence that the appliance will be imported into the EU, installed on an aircraft registered in an EU Member State, or installed on an EU–manufactured product.

(ii) The evidence must identify the ETSO appliance model at a minimum. The evidence provided must also be valid at the time of application in order for the project to be worked promptly.

FAA TSO standard via an STC, the FAA may issue an FAA TSO Letter of TSO Design Approval provided that EASA certifies that:

(i) the appliance meets the FAA TSO standard, and

(ii) EASA shall exercise continued operational safety functions for those appliances that do not have an ETSO. EASA shall maintain an internal process to monitor these appliances in the same manner as they would monitor appliances that have an ETSO standard. Note: The EASA STC/design approval must clearly identify what was approved per the FAA TSO and what, if any, installation approval is included. For FAA approval of the installation, an FAA STC validation is required per paragraph 2.2.2. (b) Issuance of an FAA Letter of TSO Design Approval.

(1) In accordance with 14 CFR §21.617, the FAA may issue a Letter of TSO Design Approval after:

(i) Receipt of all the items identified in

(5) If the application is incomplete, EASA shall notify the FAA within 10 working days and return the application in 30 days if the necessary information is not provided.

(6) In a case where there is no FAA TSO standard, but FAA has approved an appliance using an ETSO standard via an STC, EASA may issue an ETSO Authorisation provided that FAA certifies that:

(i) the appliance meets the ETSO standard, and

(ii) FAA shall exercise continued operational safety functions for those appliances that do not have an FAA TSO. (b) Issuance of EASA ETSO Authorisation.

(1) In accordance with Part 21A.606, EASA may issue an ETSO Authorisation after:

(i) Receipt of all the items identified in paragraphs 2.5.2(a)(3) and (4), above;

(ii) Conducting a review of the data/documentation specified in the ETSO performance standard;

(iii) Receipt of other specific technical data, as jointly agreed between the FAA and EASA needed to

paragraphs 2.5.1(a)(3) and (4), above;

(ii) Conducting a review of the data/documentation specified in the FAA TSO performance standard;

(iii) Receipt and review of other specific technical data, as jointly agreed between EASA and the FAA, needed to demonstrate compliance with an FAA TSO standard; and

(iv) Approval of all proposed deviations to the FAA TSO Standard in accordance with 14 CFR §21.609.

(2) The FAA may issue a Letter of TSO Design Approval without further investigation when the FAA TSO and ETSO are identical, unless there are deviations to, or it is a first-of-akind TSO (paragraphs iii and iv above). The applicant must still submit all the items identified in paragraphs 2.5.1(a)(3) and (4), above.

Note: The FAA has determined that while most ETSOs are technically similar, they are not identical to FAA TSOs due to different data or marking requirements.

demonstrate compliance with an ETSO standard; and

(iv) Approval of all proposed deviations.

(2) EASA may issue the ETSO Authorisation without further investigation when the ETSO and FAA TSO are identical, unless there are deviations, or it is a first-of-a-kind ETSO (paragraphs iii and iv above). The applicant must still submit all the items identified in paragraphs 2.5.2(a)(3) and (4), above.

Note: EASA has determined that while most FAA TSOs are technically similar, they are not identical to EASA ETSOs due to different data or marking requirements.

2.5.3 Design Approval Procedures for ETSO Authorisation for APUs. (a) Application.

(1) An application for EASA ETSOA for APU from an applicant in the United States may be submitted for APUs with an FAA TSOA, or for APUs where application for TSOA has been made to the FAA.

Note: An ETSOA is not required for an APU for which no previous individual European approval has been granted if the APU was grandfathered under EC 1702/2003 as a part of the configuration of one aircraft type design or STC and the APU is now proposed for installation on another aircraft type. Such installation can be approved under an EASA STC.

(2) FAA should ensure that the applicant’s technical data package contains the following information:

(i) Data defined in EASA Part 21A.15 and 21A.605;

(ii) The FAA TSOA, if available; and

(iii) A description of how the applicant proposes to address any APU standards differences. (3) Certification basis. EASA will determine the APU's

certification basis based on the European certification specifications applicable on the date of application to the FAA for the FAA's TSOA.

(4) Validation of Standards Differences.

(i) Where standards differences exist between the EASA certification basis and the FAA TSOA approval basis of the APU model, the applicant may use relevant service experience in support of an equivalent level of safety finding to specific standard differences where applicable.

(ii) EASA shall determine if there is a need for any additional involvement with compliance findings for the standards differences and notify the FAA. (b) Issuance of ETSOA. EASA shall issue an ETSO Authorisation for an APU after:

(1) the applicant has demonstrated compliance to the EASA certification basis, (2) the FAA has issued a TSOA, and (3) the FAA has provided a certifying statement that the APU complies with the applicable certification specifications.

2.6 Acceptance of Non-TSO Functions. (a) FAA and EASA shall accept, without further validation, data related to non- TSO functions that are integrated into an existing or proposed TSO appliance when: (1) the non-TSO functions included in the appliance do not interfere with the appliance’s functionality and/or ability to comply with the TSO standard; and (2) the data provided with the appliance relative to non-TSO functions is valid data as processed by the FAA’s or EASA’s system in accordance with the applicable VA policy. (b) If an applicant applies to have such functions included in their Letter of TSO Design Approval/ETSO Authorisation, they must be covered under the applicant’s quality system. (c) The acceptance of this additional data does not constitute installation approval. 2.7 Acceptance of Equipment Standards and Aeronautical Databases. (a) Appendix B defines equivalent RTCA and EUROCAE standards that may be used for issuing approvals under these implementation Procedures. (b) FAA and EASA have adopted comparable procedures for the acceptance of aeronautical databases used on aircraft. (FAA guidance is found in Advisory Circular (AC) 20-153, Acceptance of Data Processes and Associated Navigation Databases.) FAA shall accept an EASA Letter of Acceptance as evidence that an EU data supplier complies with RTCA/DO-200A (or European Organization for Civil Aviation Electronics (EUROCAE) ED-76). EASA shall accept an FAA Letter of Acceptance as evidence that a U.S. data supplier complies with EUROCAE ED- 76 (or RTCA/DO-200A). This acceptance does not constitute operational approval. 2.8 Procedures for Acceptance of Design Approvals for Parts.

2.8.1 Procedures for FAA Acceptance of EASA Parts Approvals. (a) Direct Acceptance by FAA of Parts Design Approvals. Not applicable.

2.8.2 Procedures for EASA Acceptance of FAA PMA. (a) Direct Acceptance by EASA of PMA Design Approvals. EASA shall directly accept PMA approvals, without further showing, for

Note: This provision is not applicable because the European Union system has no stand-alone parts design approval. Replacement or modification parts are approved through design changes or STCs. Thus, the FAA shall directly accept the design of modification and/or replacement parts when FAA has accepted or validated the design change or STC for those parts, as appropriate, without issuing a separate FAA parts design approval.

modification and/or replacement parts for installation on products certified or validated by EASA in the following cases: (1) The PMA part is not a “critical component.” (See definition, paragraph 1.6(i); or

(2) The PMA part conforms to design data obtained under a licensing agreement from the TC or STC holder according to 14 CFR §21.303; or

(3) The PMA holder is the holder of an EASA STC which incorporates the PMA part. (b) FAA PMA Parts Requiring Explicit Design Authorization by EASA.

(1) Applicability. An explicit EASA design authorization is required prior to using PMA parts as modification and/or replacement parts when:

(i) the PMA part has not been produced under a licensing agreement from the TC or STC Holder according to 14 CFR § 21.303; and (ii) the PMA part is a “critical component.” (See definition, paragraph 1.6(i)).

(2) Application. The applicant shall make an application for an STC in writing through the FAA ACO to EASA (see paragraph

2.2.3). This application should contain the following information:

(i) The FAA PMA approval, with all supplements, and in particular the description of the means by which the FAA PMA approval was granted; (ii) Overview of the technical data transmitted to the FAA for the purpose of approving the critical PMA part; (iii) Description of the means by which the PMA part user would be made aware of any changes on the PMA part by the PMA holder with a potential impact on safety; and (iv) Description of the means by which the PMA part user would be made aware of any changes by the TC holder with a potential safety impact on the PMA part.

(3) Technical validation by EASA. EASA shall issue an STC to validate the FAA PMA in accordance with the Design Approval Procedures for Non- Basic EASA STCs (see paragraph 2.2).

2.9 Environmental Testing and Approval Procedures. 2.9.1 FAA Procedures.

(a) The FAA is authorized to make findings of compliance to 14 CFR Parts 34 and 36 based upon FAAwitnessed tests conducted in accordance with FAA-approved test plans. FAA shall review and approve all compliance demonstration plans and reports submitted via the EASA. FAA environmental requirements are documented in FAA Order 8110.4, Type Certification.

(b) Upon request to EASA, and after mutual agreement, the FAA may authorize compliance test witnessing and other functions to be performed by EASA on behalf of the FAA. For tests conducted prior to a TC or STC application being made to the FAA, FAA may accept EASA-approved noise and emissions certification compliance data, provided the data meets the applicable FAA regulations, guidance, and policy material. Note: None of the bilateral airworthiness agreements listed in Attachment 1 of the Agreement have within their scope the approval of compliance with environmental standards. (c) In the absence of any authorization to EASA, the FAA process for environmental testing and approvals, includes the following:

(1) Environmental (noise, fuel venting and exhaust emissions)

2.9.2 EASA Procedures. (a) EASA is required to make findings of compliance to the environmental essential requirements, found in Article 6 of the Basic Regulation, the requirements of Part 21A.18, and in accordance with the procedures as defined in CS34 and CS36. EASA shall review and approve all compliance demonstration plans and reports submitted via the FAA.

(b) Upon request to FAA, and after mutual agreement, EASA may delegate compliance test witnessing and other functions to FAA to be performed on behalf of EASA. For tests conducted prior to a TC or STC application being made to EASA, EASA may accept FAA-approved noise and emissions certification compliance data, provided the data meets the applicable EU regulations, and EASA guidance and policy material. (c) In the absence of any delegation to FAA, or acceptable previously undertaken environmental testing, the EASA process for environmental testing and approvals, includes the following:

(1) Environmental (noise, fuel venting and exhaust emissions) certification compliance demonstration plans must be submitted to EASA for review, comment, and subsequent approval prior to undertaking

certification compliance demonstration plans must be submitted to the FAA for review, comment, and subsequent approval prior to undertaking certification testing. (2) Information and data must be supplied to the FAA in order to conduct an evaluation of the measurement and analysis methods and practices, and data correction procedures of the applicant for aircraft noise certification under 14 CFR Part 36, Subpart B and/or Subpart H. (3) Aircraft noise compliance demonstration test plans and engine exhaust emissions test plans to be used for demonstrating U.S. environmental certification compliance must be submitted to the FAA for review and comment, and subsequent approval not less than 90 days prior to commencing testing. (4) Proposed equivalent procedures to be used by the applicant during testing, data processing, data reduction, and data analysis must be specifically identified to the FAA and approved in advance by the FAA as part of items (1), (2) and (3) above. (5) Compliance demonstration tests must be witnessed by FAA personnel or authorized FAA designees. Prior to the start of testing it is necessary to assure

certification testing.

(2) Information and data must be supplied to the EASA in order to conduct an evaluation of the measurement and analysis methods and practices, and data correction procedures of the applicant for aircraft noise certification under CS36.

(3) Aircraft noise compliance demonstration test plans and engine exhaust emissions test plans to be used for demonstrating compliance must be submitted to the EASA for review and comment, and subsequent approval not less than 90 days prior to commencing testing.

(4) Proposed equivalent procedures to be used by the applicant during testing, data processing, data reduction, and data analysis must be specifically identified to the EASA and approved in advance by EASA as part of items (1), (2) and (3) above.

(5) Compliance demonstration tests must be witnessed by EASA personnel or EASA approved delegates. Prior to the start of testing it is necessary to assure the conformity of the test article (aircraft or engine configuration) to that identified in the EASA approved compliance demonstration test plans.

the conformity of the test article (aircraft or engine configuration) to that identified in the FAA approved compliance demonstration test plans.

(6) Compliance demonstration reports must be submitted to the FAA for review and/or comment and subsequent approval prior to type certification approval.

(d) The following actions must be performed by the FAA and are not subject to the delegation process.

(1) In addition to compliance with 14 CFR Part 36, information and data must be supplied to the FAA in order to make a finding in accordance with Title 49 U.S.C. Section 44715 (previously known as the Noise Control Act of 1972). The FAA, before issuing an original type certificate for an aircraft of any category, must assess the extent of noise abatement technology incorporated into the type design and determine whether additional noise reduction is achievable. This examination must be initiated as soon as possible after the application for type certification in each original type certification project and reflect noise reduction potentials that become evident during the design and certification process.

(2) The National Environmental Policy Act of 1969 (NEPA) requires the FAA

(6) Compliance demonstration reports must be submitted to the EASA for review and/or comment and subsequent approval prior to type certification approval.

to publicly assess and analyze potential environmental consequences of its actions. In order to grant an aircraft type certificate (new, amended, or supplemental) in the absence of noise regulations that are applicable and appropriate to a particular aircraft type, the FAA must prepare an Environmental Assessment, including a decision on whether to prepare a finding of no significant impact or an environmental impact statement. Information and data must be supplied to the FAA in order to prepare the Environmental Assessment.

2.10 Recordkeeping Requirements.

2.10.1 U.S. design approval holders are required to hold relevant design information and to make it available to the FAA upon request in accordance with FAA regulations and policy (14 CFR §21.49 for TC holders; CFR §21.49 and FAA Order 8110.4, Type Certification, for STC holders; CFR §21.613 for TSO Authorization holders; and CFR §21.303 and FAA Order 8110.42, Parts Manufacturer Approval Procedures, for PMA holders.) This information is available from the design approval holders via the FAA upon request from EASA. (Note: U.S. approval holders using electronic formats must comply with FAA Order 8000.79, Use of Electronic Technology and Storage of Data.)

2.10.2 In accordance with EU law and EASA Part 21, approved organizations are required to hold relevant design information and make it available upon request. This information is available from the design approval holders via EASA upon request from the FAA. In cases where an EU approval holder chooses to submit data in electronic format, a written procedure on the use of electronic technology and storage of data shall be established with EASA.

2.10.3 When an applicant in the U.S. or EU complies with FAA's Order 8000.79 or EASA's electronic data policy, as applicable, the applicant is considered to have

an arrangement acceptable to both the FAA and EASA for the submission and storage of electronic data so long as the data is in a format that is compatible with the VA’s information system.

SECTION III POST DESIGN APPROVAL PROCEDURES 3.0 General. This Section consists of procedures for continued airworthiness, design changes including FAA approved or accepted alterations, and approval of design data used in support of repairs. 3.1 Continued Airworthiness.

3.1.1 General. (a) FAA in carrying out State of Design functions applicable to the United States under Annex 8 of the Chicago Convention, and EASA in carrying out the State of Design functions applicable to European Union Member States, are responsible for resolving in-service safety issues related to design. The FAA and the AA or where applicable, EASA, is responsible for resolving in-service safety issues related to production under their respective regulatory jurisdictions. (b) FAA or EASA shall provide applicable information which it has found to be necessary for mandatory modifications, required limitations and/or inspections to the importing authority to ensure continued operational safety of the product, part, or appliance. The importing authority shall review and normally accept the corrective actions taken by the authority representing the State of Design, or where applicable the State of Manufacture, in the issuance of its own mandatory corrective actions.

(c) At the request of the importing authority, the exporting authority, carrying out State of Design functions, shall assist the importing authority in determining what importing authority action is considered necessary for the continued operational safety of the product, part, or appliance.

(d) The FAA and EASA shall strive to resolve differences, but the decision as to the final action to be taken with respect to the products, parts, or appliances under the jurisdiction of the importing country lies solely with the importing authority following consultation with the exporting authority as described in paragraph 3.1.4.(c). (e) The FAA and EASA recognize the importance of the routine sharing of Continuing Airworthiness information as a means to assist in the identification and resolution of emerging airworthiness issues. (f) With regard to post-type validation activities, the FAA or EASA as VA has the right to seek information, including access to design data, to understand and agree on findings of compliance made by the CA to all VA requirements and on any mandatory corrective action or any significant on-going continued airworthiness topic and its means of resolution, necessary to ensure acceptable

continued airworthiness of aircraft registered in the jurisdiction of the VA and engines, propellers, and appliances installed on any such aircraft. (g) The FAA and EASA shall establish structured processes, including specific focal points, for regular feedback and communicating continued airworthiness issues on products certified by either FAA or EASA and validated by the other. The extent of these processes shall be commensurate with the continued airworthiness activities associated with the product.

3.1.2 Sharing of In-Service Reports and Information on Malfunctions, Failures, or Defects.

(a) The FAA and EASA agree to perform the following functions for the products, appliances, and parts exported to the other’s jurisdiction:

(1) Collecting information on in-service safety events, malfunction/failure/defects, and accident/incidents. (2) Evaluating in-service safety events and malfunction/failure/defect reports and accident/incidents. (3) Investigating and resolving all suspected unsafe conditions. (4) Advising the importing authority of all unsafe conditions and the necessary corrective actions (see paragraph 3.1.4 below). (5) Upon request, when concerning matters of safety for products registered in the importing country, providing the importing authority with the following:

(i) Reports of malfunctions, failures, or defects and accidents/incidents; (ii) Status of investigations into malfunctions, failures, or defects and accidents/incidents; (iii) Copies of conclusions reached in its investigation into malfunctions or defects; and (iv) Copies of conclusions reached in investigations into accidents/incidents in accordance with ICAO Annex 13.

(6) Making a reasonable effort to resolve issues raised by the importing authority concerning matters of safety for products registered in the importing country.

(b) The FAA and EASA agree to perform the following functions:

(1) Advising each other of malfunctions or defects and accidents/incidents which are believed to be potentially unsafe conditions occurring on the products and appliances which are imported from the country of the exporting authority. (2) Supporting each other in the investigations of unsafe conditions and their occurrences on the imported aircraft and in the resolution of continued airworthiness issues directly related to an accident or incident in the jurisdiction of either the FAA or EASA. (3) Advising each other, if as a result of investigations made by the importing authority into malfunctions or defects and accidents/incidents and consultations with the other, it has determined that it shall make corrective actions mandatory.

(c) Copies of U.S. SDR/Malfunction or Defect reports are available from the FAA Delegation and Airworthiness Programs Branch, AIR-140. Copies of U.S. SDR and accident/incident reports are also available on the FAA’s internet web site at www.faa.gov (http://av-info.faa.gov/isdr). Copies of EU malfunction or defect reports are available from the EASA Certification Directorate, Products Department.

3.1.3 Sharing Information on Any Airworthiness Limitation Changes. The FAA and EASA shall share information on any changes that affect operating limitations, life limits, or any other airworthiness limitation, including manual changes and changes to certification maintenance requirements. These changes should be promptly sent to the importing authority in order to ensure the continued operational safety of the aircraft. The FAA and EASA shall treat a reduced life limit as an unsafe condition and shall accordingly issue an Airworthiness Directive (AD). The FAA and EASA may also issue an AD for other limitation changes if they are considered an unsafe condition. 3.1.4 Unsafe Condition and Mandatory Continuing Airworthiness Information.

(a) The FAA (under 14 CFR Part 39) and EASA (under EASA Part 21), issue mandatory continuing airworthiness information. The FAA and EASA agree to perform the following functions listed below for the products, appliances, parts and design changes for which it is the CA.

(1) Issuing mandatory continuing airworthiness information whenever the responsible authority determines that an unsafe condition exists in a type certificated product or appliance, and is likely to exist or develop on a type certificated product or appliance of the same design. This may include a product that has an engine, propeller, part, or appliance installed on it and the installation causes the unsafe condition. The contents of such mandatory continuing airworthiness information should include, but are not limited to, the following:

(i) Make, model, and serial numbers of affected aircraft, aircraft engines, propellers, appliances, and parts;

(ii) Description of the unsafe condition, reasons for the mandatory action, and its impact on the overall aircraft and continued operation;

(iii) Description of the cause of the unsafe condition (e.g., stress corrosion, fatigue, design problem, quality control, unapproved part); (iv) The means by which the unsafe condition was detected and, if resulting from in-service experience, the number of occurrences; and (v) Corrective actions and corresponding compliance times, with a list of the relevant manufacturer’s service information including reference number, revision number and date. (2) Ensuring that the following information is provided to the VA as part of the mandatory continuing airworthiness information or directly from the approval holder:

(i) The number of aircraft worldwide needing corrective action; (ii) A statement on the availability of parts; and (iii) An estimate of the total number of labor hours and the cost of parts required for the corrective actions. (This total should include all applicable supplier labor hours and costs.)

(3) Issuing a revised or superseding mandatory continuing airworthiness information whenever the responsible authority finds any previously issued mandatory continuing airworthiness information was incomplete or inadequate to fully correct the unsafe condition.

(4) Notifying the importing authority of the unsafe condition and the necessary corrective actions by electronically submitting a copy of the mandatory continuing airworthiness information at the time of publication to the electronic mail addresses referenced in Appendix A. Additionally, the FAA or EASA shall arrange for copies of all relevant service bulletins referenced in their mandatory action, including any supplier service bulletins, as well as other supporting documentation, to be forwarded to the appropriate focal point in the product-responsible FAA Directorate and EASA Certification Manager, as applicable.

(5) Providing advance electronic notice of anticipated emergency ADs (including security-sensitive ADs) or other significant safety events that affect continued airworthiness. (6) Ensuring, in the case of emergency airworthiness action, special handling so that the importing authority is notified prior to adoption of the mandatory continuing airworthiness information. (7) Advising and assisting the importing authority in defining the appropriate actions for the importing authority to take in the issuance of its own mandatory continuing airworthiness information. (8) Maintaining a web-based database of mandatory continuing airworthiness information that can be accessed by the State of Registry. (b) The FAA and EASA agree to perform the functions listed in paragraph 3.1.4(a) when an unsafe condition is related to production or maintenance of the products, appliances, and parts under this Agreement. For certain cases of unsafe condition related to production or maintenance, EASA may issue an Emergency Conformity Information (ECI) instead of an AD. Both AD and ECI are EASA issued Mandatory Continuing Airworthiness Information under ICAO Annex 8. (c) The FAA and EASA recognize that they may disagree as to the finding of an unsafe condition and propose to issue a unilateral AD. In that case, it is expected that the VA shall consult in a timely manner as follows prior to issuing any AD that substantially deviates or is additional to those issued by the CA.

(1) The responsible office of the VA shall consult with its counterpart organization. (2) If the CA agrees that the proposed mandatory action is needed, then it shall issue an AD.

(3) If the CA disagrees with the proposed mandatory action, it shall notify the VA with its written justification via email. The VA shall review the justification and determine whether or not to continue its AD action.

(4) If the decision is to continue with a unilateral AD, the VA shall hold a teleconference with appropriate management of both Technical Agents (FAA Directorate Manager and EASA Head of Products) to advise that unilateral AD action shall commence. (d) The FAA and AA shall similarly consult if they disagree as to the finding of an unsafe condition related to production or maintenance. (e) In the situation where the FAA or EASA works with a manufacturer to conduct a monitored retrofit/recall of the global fleet of aircraft or parts, the FAA or EASA shall notify each other of this activity. (f) The FAA and EASA agree to respond quickly to the issuance of a mandatory continuing airworthiness action by the exporting authority in making its own determination of the need for issuing its own similar mandatory continuing airworthiness action that addresses the unsafe condition on the affected product certified, approved or otherwise accepted by the importing authority.

(g) EASA shall immediately notify the FAA of any known immediate safety actions taken by an AA under the provisions of Article 14(1) of Regulation (EC) 216/2008 on products, appliances, parts and design changes for which the FAA carries out the functions of State of Design.

3.1.5 Alternative Means of Compliance (AMOC) to a Mandatory Continuing Airworthiness Action. If an AMOC of general applicability to an existing AD is issued by the CA for its own State of Design products, the CA shall electronically notify the VA of the decision. 3.1.5.1 At the AMOC holder’s request, EASA shall initiate FAA approval of such an AMOC by providing sufficient information to the FAA for its use in making a determination as to the acceptability of the AMOC. Based on this information, the FAA shall write an AMOC approval letter for U.S. operations.

3.1.5.2 FAA AMOCs for U.S. State of Design products of general applicability are automatically considered to be EASA-approved.

3.2 Design Changes.

3.2.1 Procedures for Changes to a Type Certificate by the Type Certificate Holder and Changes to a Supplemental Type Certificate by the Supplemental Type Certificate Holder.

(a) Changes to a type design that require a new TC or STC should be done in accordance with paragraphs 2.1 and 2.2, respectively.

(b) All other changes to a type design by the TC holder or STC holder (on their own STC) should be done in accordance with the Post-Type Validation Principles (Appendix C of this document). These types of changes include: amended type certificates (derivative models), amendments to STCs; and those changes necessary for customer unique design features, product improvements and any other design changes, including revisions to approved manuals, made by the TC or STC holder, for whatever reason.

(c) Irrespective of paragraph 3.2.1(b), any change in type design, minor or major, that may increase the noise levels of the aircraft or that may increase the fuel venting or exhaust emissions of an engine should be done in accordance with paragraph 3.2.6.

(d) The FAA shall employ its procedures as defined in FAA Order 8110.52 to implement the Post-Type Validation Principles. EASA shall employ the procedures defined in the Appendix C of this document.

(e) Where design changes are proposed, they shall be defined relative to the VA’s current definition of the approved type design. (f) For changes to a type design, except for acoustical or emissions changes, the VA’s date of application is the date application was made to the CA for the change. For design changes, the FAA shall develop its certification basis in accordance with 14 CFR §21.101, and §21.93(b) and (c). EASA shall develop its certification basis in accordance with EASA Part 21.101. FAA and EASA shall consult when changes to the certification basis justify using the TVP process to validate an amended TC. (g) In the case of an acoustical change, for FAA approval compliance must be shown with the applicable noise requirements of 14 CFR Part 36 in effect on the date of application to the FAA for approval of the design change. In the case of an emissions change, for FAA approval compliance must be shown with the applicable fuel venting and exhaust emissions requirements of 14 CFR Part 34.

(h) Design changes shall be classified as either Major or Minor in accordance with the CA’s criteria and procedures. Design changes classified as Major shall be further categorized as Level 1 Major and Level 2 Major in accordance with Post- Type Validation Principles (see Appendix C). (i) In discharging its responsibilities, the VA should seek to rely on the findings made and actions taken by the CA to the maximum extent possible.

(j) The VA’s involvement shall be limited to activities, including design changes, affecting aircraft types registered, or due to be registered, in the VA’s jurisdiction and other products imported or planned to be imported, except where the TC or STC holder requests greater VA involvement (e.g., for design changes that could eventually be incorporated into the VA fleet) and this is agreed by the certificating and validating authorities.

(k) The CA shall address relevant changes to the ICA during its design change approval. If changes to the ICA are required, these changes must be communicated to the VA. 3.2.2 Procedures for Major Changes to a Type Design by Persons Other Than the TC/STC Holder. For major changes to a type design by persons other than the TC/STC holder, the FAA and EASA agree to follow the design approval procedures in paragraph 2.2 for STCs.

3.2.3 Procedures for Minor Changes to a Type Design by Persons Other Than the TC/STC Holder.

(a) For the FAA, minor design change data by other than the TC/STC holder are approved using PMA procedures or through alterations. EASA's acceptance of PMA is addressed in paragraph 2.8 and the acceptance of alterations is addressed in paragraph 3.2.4 below. (b) For EASA, all minor changes to the type design must be approved in accordance with EASA Part 21. Minor changes can be approved by a DOA or EASA in the EU system. These minor changes are considered approved by FAA, except when retained by FAA per paragraph 3.2.6.1(a), following the approval under EASA's system on behalf of the State of Design for the design change.

3.2.4 Procedures for Acceptance of Design Data in Support of FAA Alterations.

3.2.5 Procedures for Changes to Appliances by the Design Approval Holder. 3.2.5.1 Procedures for Changes to an FAA Letter of TSO Design Approval.

(a) Major changes to a TSO design require re-substantiation of the new design and issuance of a Letter of TSO Design Approval, and shall be done in accordance with the procedures in paragraph 2.5.1.

(b) FAA shall rely upon an EASA determination of compliance for minor changes that remain within the scope of the Letter of TSO Design Approval. FAA shall not require notification of these minor changes.

3.2.5.2 Procedures for Changes to an EASA ETSO Authorisation.

(a) Major changes to an ETSO design require re-substantiation of the new design and issuance of a new ETSO Authorisation. The procedures in paragraph 2.5.2 apply in this case.

(b) EASA shall rely upon an FAA determination of compliance for minor changes that remain within the scope of the ETSO Authorisation. EASA shall not require notification of these minor changes.

3.2.4.1 FAA Acceptance of EASA Alteration Data.

Not applicable. Note: This provision is not applicable because the European system has no equivalent to FAA’s alterations. Alterations are approved through design changes or EASA STCs.

3.2.4.2 EASA Acceptance of FAA Alteration Data. (a) Except for alterations on critical components, FAA approved or accepted alterations per 14 CFR Part 43, installed on an aircraft exported from the U.S., regardless of the State of Design of the aircraft, are considered approved by the EASA at the time of import to the European Union. EASA shall accept such FAA alteration data when substantiated via an appropriately executed FAA Form 8110-3, 8100-9, or FAA Form 337 or logbook entry.

(b) Alterations on critical components must be EASA-approved via STC in accordance with paragraph 2.2.

3.2.5.3 Procedures for Changes to an EASA ETSO Authorisation for APUs.

(a) Major changes to an ETSO APU design require re-substantiation of the new design and issuance of a new ETSO Authorisation for APUs. The procedures in paragraph 2.5.3 apply in this case.

(b) Minor changes, including bracket changes approved under 14 CFR §21.605(b), shall be accepted by EASA without further review. The FAA shall review the design change against the EASA certification basis.

(c) The FAA shall notify EASA about any new APU model designation identified through bracket changes following its FAA approval. For all other minor design changes not resulting in a new APU model designation, the FAA shall arrange for the changes to be recorded in the definition of the EASA approved APU configuration. A listing of these changes shall be transmitted to the EASA Certification Manager for Propulsion on a yearly basis and shall also be made available at any time, upon request from EASA.

3.2.6 Procedures for Changes to a Type Design (TC/STC) Affecting Noise and Emissions.

3.2.6.1 FAA Noise and Emissions Requirements for Changes to Type Design. (a) Any determination of an acoustical or emissions change,

3.2.6.2 EASA Noise and Emissions Requirements for Changes to Type Design. All design changes having an appreciable effect on noise, fuel venting, or exhaust emission are classified as Major under paragraph

regardless if the type design change is major or minor, requires further demonstration of compliance. The FAA retains all findings of acoustical or emissions change under 14 CFR §21.93(b) & (c).

(b) A technical substantiation must be provided to the FAA to determine whether or not the changes may be considered an acoustic or emissions changes for type design changes that:

(1) have any affect on the performance characteristics of the aircraft, (e.g. drag, weight, lift, power, RPM, etc.); (2) add or modify any externally radiating noise sources, (e.g. APU operation, fuselage distensions, wing extensions, rigging changes, hollow cavities in landing gear or airframe, etc.); and/or

(3) modify the engine(s), nacelle(s), propeller (s), or rotor system, (c) Technical substantiation is not required for type design changes that have no possibility of affecting the noise or emissions certification levels, e.g. type design changes involving a component internal to the fuselage.

3.2.1(h), and regardless of whether the change is classified as Level 1 or Level 2, shall be subject to the EASA procedures for environmental testing and approval described under paragraph 2.9.2.

3.3 Approval of Design Data Used in Support of Repairs. 3.3.1 Design data used in support of repairs must be approved or accepted, as appropriate, by the exporting authority (State of Design). The following describes the process that shall be followed by FAA and EASA so that repair design data can be approved or accepted. Repair designs for the fabrication of new parts are not

eligible for acceptance or approval (import) under these Implementation Procedures.

3.3.2 FAA and EASA Repair Design Data Approval Process.

(a) FAA shall approve design data in support of major repairs in accordance with FAA Order 8110.4 Type Certification; FAA Order 8110.37, Designated Engineering Representative Guidance Handbook; FAA Order 8100.15, Organization Designation Authorization Procedures; and FAA Order 8900.1, Flight Standards Information Management System. Minor repairs are made in accordance with “acceptable” data, in accordance with 14 CFR Part 43.

(b) EASA shall approve design data in support of repairs in accordance with EASA Part 21 Subpart M-Repairs and EASA’s procedure Type Certificate Change and Repair Approval. A design approval shall be issued for all Union repair design data.

3.3.3 FAA Acceptance of EASA Repair Design Data.

(a) General.

(1) Except as provided in (b) below, the FAA shall accept EASA approved design data produced under EASA Part 21 Subpart M used in support of major or minor repairs regardless of the State of Design of the product, part, or appliance, if:

(i) the FAA has certificated/validated the product or appliance,

(ii) EASA is acting on behalf of the State of Design for the repair design data,

(iii) EASA repair design data approval is substantiated via a repair

3.3.4 EASA Acceptance of FAA Repair Design Data. (a) Non-Critical Components.

(1) EASA shall accept data used in support of major repairs regardless of the State of Design of the product, part or appliance, if:

(i) EASA has certificated/validated the product or appliance,

(ii) the FAA is the authority of the State of Design for the repair design data, and

(ii) the FAA repair design data approval is substantiated via an FAA letter or properly executed FAA Form 8110-3, 8100-9, or FAA Form 337. (2) EASA shall also accept data

design approval letter or a repair design approval issued under a DOA. For repair data approved prior to September 28, 2003, in France, Germany, Italy, the Netherlands, Sweden, and the United Kingdom, FAA shall accept either the AA approval document, or equivalent, or a repair design approval issued under a former national DOA as evidence of the approval, and (iv) the repair is not in an area that is subject to an FAA AD, unless the AD allows for acceptance of an EASA repair design approval.

(2) In these circumstances, repair design data are considered to be approved by the FAA following its approval under EASA’s system. This process does not require application to the FAA or compliance findings to the FAA certification basis. (b) For major repair design data for critical components by other than the TC/STC holder:

(1) The applicant shall submit an application to EASA with a request that the application and required information be forwarded to the applicable FAA Directorate Standards

used in support of minor repairs when:

(i) EASA has certificated/validated the product or appliance,

(ii) the FAA is the authority of the State of Design for the repair design data, and

(iii) the repair design data has been provided by a U.S. TC/STC or TSOA holder, or

(iv) for minor repairs from other than a U.S. TC/STC or TSOA holder, the determination that data are acceptable (under 14 CFR Part 43) has been made by a U.S. maintenance organization under FAA’s authorized system,

Note: An EU company must use EASA Part 21 for the approval of repair data for use on an EU-registered aircraft. Unless the minor repair data has been previously used to repair an N-registered aircraft, an EU company cannot determine any data to be acceptable data under 14 CFR Part 43 for use on an EU-registered aircraft. (3) In these circumstances, repair design data are considered to be EASA-approved following its approval or acceptance under FAA’s system. This process does

Staff as listed in Appendix A.

(2) In cases where the applicant has entered into an arrangement with the TC/STC holder, EASA shall confirm this to the FAA. FAA shall issue a letter approving the major repair based on EASA's repair data approval without further technical review. (3) In cases where the applicant has not entered into an arrangement with the TC/STC holder, EASA shall ensure that each application contains the following:

(i) drawings, specifications and other data necessary to define the configuration and design features of the repair;

(ii) a compliance summary that identifies the applicable airworthiness standards, methods of compliance, and compliance results;

(iii) substantiation for continued applicability of existing ICAs or supplemental ICAs, if any; and (iv) an EASA statement that the approved repair brings the product or part back to an airworthy condition.

not require application to EASA or compliance findings to the EASA certification basis.

(b) Critical Components

(1) EASA shall accept any critical component repair design data from a TC/STC holder, regardless of the State of Design of the product, if.

(i) EASA has certificated/validated the product, and

(ii) the FAA is the authority of the State of Design for the repair design data.

(iii) In these circumstances, repair design data are considered to be EASAapproved following its approval under FAA’s system. This process does not require application to EASA or compliance findings to the EASA certification basis.

(2) EASA shall approve critical component repair design data by other than the TC/STC holder, regardless of the State of Design of the product, as follows:

(i) The applicant shall submit an application to the FAA with a request that the application and required information be forwarded to EASA, as listed in Appendix A. The application

(4) FAA shall then issue a letter approving the major repair design following issuance of EASA's repair design approval.

for approval of the repair design data shall be made to EASA in the manner prescribed on EASA’s website.

Continue reading ↓ 120 of 317 passages shown