Order 6750.16D Siting Criteria for Instrument Landing Systems
This document is cancelled. Cancelled by 6750.16E. Check the official source before relying on it.
Text read by OCR from a scanned file. Check the original, as some words may be misread.
ORDER 6750.16D
ORDER 6750.16D
SITING CRITERIA
FOR
INSTRUMENT LANDING SYSTEMS
February 14, 2005
DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION
Distribution: A-WXYZ-1; A-FFS-0 (SUPV); A-FIA-0 (SUPV) Initiated By: Technical Operations A-FAS-1 (SUPV); A-FAT-2 (SUPV); A-FAF-0 (LTD) (AND-720)
RECORD OF CHANGES
RECORD OF CHANGES
CHANGE TO SUPPLEMENT OPTIONAL
BASIC
FAA FORM 1320-5 (6-80) USE PREVIOUS EDITION
CHANGE TO BASIC
DIRECTIVE NO 6750.16D
SUPPLEMENT OPTIONAL
FOREWORD
The material in this order is a result of a total revision of Order 6750.16C. The purpose of the revision is to delete obsolete material that addressed antenna systems and other units that are no longer used, certain practices and requirements that are no longer required, and items of a similar nature.
SUPPLEMENT OPTIONAL
Števe Ząidman Vice President Technical Operations Services
i (and ii)
2/14/2005
TABLE OF CONTENTS
CHAPTER 1. GENERAL INFORMATION 1-1. PURPOSE.. 1-2. DISTRIBUTION. 1-3. CANCELLATION. 1-4. EXPLANATION OF CHANGES 1-5. APPLICATION 1-6. DIRECTIVE VERBS. 1-7. PROCEDURES.. 1-8. INTRODUCTION 1-9. ILS ESTABLISHMENT CRITERIA.. 1-10. ILS COMPONENTS AS OBSTRUCTIONS
TABLE OF CONTENTS
6750.16D
...1-1 .1-1 1-1 .1-1 .. 1-1 ..1-2 .1-2 1-2 .1-3 .1-3 .1-4
NATIONAL AIRSPACE SYSTEM CHANGE PROPOSAL (NCP)
1-11. 1-12. GENERAL DESCRIPTION OF THE ILS. 1-13. SITING EFFECTS ON ILS OPERATIONS 1-14. MULTIPLE ILS ESTABLISHMENTS. 1-15. ILS CRITICAL AREAS. 1-16. ILS SHELTER STANDARDS 1-17. RESERVED.
NATIONAL AIRSPACE SYSTEM CHANGE PROPOSAL (NCP)
CHAPTER 2. THE ILS LOCALIZER.
2-1. GENERAL DESCRIPTION. 2-2. LOCALIZER LOCATION AND TYPES 2-3. LOCALIZER EQUIPMENT SHELTER.. 2-4. DESCRIPTION OF THE ANTENNA SYSTEMS 2-5. SITING REQUIREMENTS. 2-6. GROUND CHECK POINTS (SEE FIGURE 2-5.) .. 2-7. SITE EFFECTS ON LOCALIZER PERFORMANCE 2-8. RESERVED
CHAPTER 3. THE ILS GLIDE SLOPE
CHAPTER 3. THE ILS GLIDE SLOPE
3-1. GENERAL DESCRIPTION. 3-2. GLIDE SLOPE ANTENNA ARRAY SELECTION
1-4 1-4 ..1-5 ..1-6 .1-9 .1-14 1-14
.2-1
2-1 .2-4 .2-5 .2-5 2-6 .2-10 .2-11 .2-17
..3-1
.3-1 .3-2
TERRAIN CONSIDERATIONS FOR IMAGE-TYPE GLIDE SLOPES.
3-3. 3-4. SITE PREPARATION.. 3-5. RESERVED. 3-6. ENDFIRE GLIDE SLOPE CRITERIA. 3-7. LOCATING THE GLIDE SLOPE FACILITY 3-8. PHYSICAL REQUIREMENTS. 3-9. RESERVED. 3-10. REQUIRED OBSTRUCTION CLEARANCE (ROC) 3-11. SUMMARY.
3-1. GENERAL DESCRIPTION. 3-2. GLIDE SLOPE ANTENNA ARRAY SELECTION
CHAPTER 4.1 MARKER BEACONS AND ANCILLARY AIDS.
4-1. MARKER BEACONS.
V
.3-2 ..3-8 ..3-11 .3-11 .3-12 ..3-26 ..3-26 .3-26 .3-26
2/14/2005
4-2. DISTANCE MEASURING EQUIPMENT (DME) 4-3. COMPASS LOCATORS.. 4-4. RESERVED. 4-5. RESERVED. CHAPTER 5. MONITOR AND CONTROL REQUIREMENTS. 5-1. GENERAL REQUIREMENTS.. 5-2. EQUIPMENT REQUIREMENTS.. 5-3. CONNECTIVITY REQUIREMENTS. 5-4. RESERVED. CHAPTER 6. ILS POWER REQUIREMENTS. 6-1. FACILITY REQUIREMENTS 6-2. RESERVED.. 6-3. INSTALLATION REQUIREMENTS. 6-4. STANDBY POWER... 6-5. CONTINUOUS POWER AIRPORT 6-6. RESERVED.
6750.16D
.4-4 .4-5 .4-5 .4-5 .5-1 .5-1 ..5-2 .5-3 .5-3 .6-1 .6-1 .6-1 .6-1 .6-1 .6-1 .6-1
PROJECT ENGINEERING AND FACILITY ESTABLISHMENT … 7-1
PROJECT ENGINEERING AND FACILITY ESTABLISHMENT … 7-1
CHAPTER 7. 7-1. GENERAL PROCEDURE. 7-2. PRELIMINARY SURVEY 7-3. PRELIMINARY REPORT 7-4. FINAL ENGINEERING ACTIVITIES. 7-5. SITE TESTING APPENDIX 1. GLOSSARY. APPENDIX 2. LOCALIZER SITE EFFECTS. APPENDIX 3. GLIDE SLOPE SITE EFFECTS. APPENDIX 4. RDH/ARDH CONSIDERATIONS. List of Figures
Figures
1-1 Multiple ILS Configurations.. 1-2 Category I, II, & III Localizer Critical Area.. 1-3 Image Glide Slope Critical Area .. 1-4 End Fire Glide Slope Critical Area.. 2-1 ILS Course Displacement Reference Points ... 2-2 Typical Localizer Degrading Sources .. 2-3 Offset Localizer Configuration ... 2-4 Typical Localizer Plot Layout and Site Grading Requirements...
V
7-1 .7-1 7-1 .7-2 7-2 ..1 ...1
...1 .1
Page
.1-8 .1-11 1-12 1-13 .2-2 .2-3 .2-4 .2-10
2-5 Localizer Ground Check Points. .2-11 2-6 LPD vs Vring . .2-14 2-7 SBO Pattern Comparison.. 2-15 2-8 8 Element Array (45-Foot Aperture) . .2-16 2-9 14-Element Array (86-Foot Aperture) ... .2-17 3-1 Image Antenna Concept.. .3-3 3-2 First Fresnel Zones For ILS Glide Slope .. .3-4 3-3 Location Of Glide Slope Geometric Ground Reflection Points . ..3-5 3-4 Location Of Glide Slope Fresnel Zone Centers. .3-6 3-5 First Fresnel Zone Length As Function Of Glide Angle And Aircraft Distance From Glide Slope.. .3-6 3-6 First Fresnel Zone Width As Function Of Glide Angle And Aircraft Distance From Glide Slope .. ..3-7 3-7 Grading Criteria For Image-Type ILS Glide Slopes .. .3-10 3-8 Expected Applicability Of Glide Slope Systems To Different Siting Conditions … 3-11 3-9 Identification Of Glide Slope Siting Parameters .3-14 3-10a Typical End-Fire Glide Slope Equipment Layout Dual-Clearance Configuration … 3-17 3-10b Typical End-Fire Glide Slope Equipment Layout Single-Clearance Configuration ... 3-18 3-11 Glide Slope Site With Ideal Terrain... .3-19 3-12 Longitudinal Terrain Slope Down From Glide Slope To Threshold … 3-20 3-13 Longitudinal Terrain Slope Up From Glide Slope To Threshold … 3-20 3-14 Pedestal Case, Height A. ..3-21
V
2/14/2005
3-15 Glide Slope Site With Positive Terrain Slope. 3-16 Glide Slope Site With Negative Terrain Slope. 3-17 Site With Irregular Slope 4-1 Siting Criteria For Collocated Marker And Compass Locator. 4-2 Compass Locator Elevation And Plot Size Requirements..
vi
6750.16D
.3-23 .3-24 .3-25 4-3 4-4
2/14/2005
APPENDIX 2.
Figures
A2-1 Scalloping Effect - Orbital Flight . A2-2 Scalloping Effect - Radial Flight . A2-3 Scalloping Effect - Angular Flight.. A2-4Analysis of Scalloping - Example 1 A2-5 Analysis of Scalloping - Example 2 .. A2-6Analysis of Scalloping - Example 3 .... A2-7 Signal Cancellation Concept ... A2-8 Effect of a Cancellation Wire on a Reflected Signal.. A2-9 AC Power Line Signal Reflection Cancellation .
APPENDIX 3.
Figures
A3-1 Fresnel Zone for ILS Glide Slope A3-2 Effect Of Rough Terrain On Glide Path .. A3-3 Terrain Roughness Criterion.
vii
6750.16D
Page
..3 ...3
.4
..5 ..6 ..7 ..8 ...9 ..10
Page
..2
..6 ..8
APPENDIX 4. Figures Page
APPENDIX 4. Figures Page
Figure A4-1 RDH and ARDH versus Longitudinal distance from the Antenna Mast to Threshold for Antenna Mast Offset Distances from Centerline of 250, 450, and 650 Feet for a Path Angle of 3.00 Degrees .. ..3 Figure A4-21 Illustration of the Effect of a Uniform, Longitudinal, Up-Sloping Terrain Gradient On The RDH.. Figure A4-3a Illustration of a CEGS with Stepped Terrain, Depicting the Modeled Differences between RDH/ARDH and TCH. Figure A4-3b Illustration of of a CEGS with Multiple Slope Terrain, Depicting the Modeled Differences between RDH/ARDH and TCH..
List of Tables Tables Page
Table 2-1 Localizer Antenna Arrays ... .2-6 Table 2-2 Minimum Normal Course Width for Single-Frequency Localizer Arrays for which Greater Than 60% Abnormal Case DDM will not occur. ..2-13 Table 4-1 Typical ILS Marker Characteristics.. .4-1
viii
CHAPTER 1. GENERAL INFORMATION
CHAPTER 1. GENERAL INFORMATION
1-1. PURPOSE
This order provides guidance to engineering personnel engaged in the siting of Federal Aviation Administration (FAA) instrument landing systems (ILS). Sufficient information, supplemented by relevant drawings, will enable the engineer to select the optimum site, within defined limits, for each of the subsystems that comprise a Category I, II, or III ILS. Because of the wide variation in ILS siting conditions, it is not possible to provide specific instructions on how to overcome or offset the effects of each adverse condition. This order provides guidelines that must be used in conjunction with a thorough understanding of ILS facility operations to arrive at the optimum site and operating parameters.
1-2. DISTRIBUTION
1-2. DISTRIBUTION
This order is distributed to all heads of offices and services in Washington headquarters, the regions, the Mike Monroney Aeronautical Center, and the William J. Hughes Technical Center; to all supervisors in the Flight Standards Field Offices, International Aviation Field Offices, Airports Field Offices, and Air Traffic Airport Traffic Control Tower Field Offices; and to all Airway Facilities field offices with a limited distribution.
1-3. CANCELLATION
1-3. CANCELLATION
Order 6750.16C, Siting Criteria for Instrument Landing Systems, dated October 31, 1995 is cancelled.
1-4. EXPLANATION OF CHANGES
This revision provides updates and clarification to criteria throughout the Order and deletes material that has become obsolete. Some of the more significant changes include the following:
1-4. EXPLANATION OF CHANGES
a. Para 1-13 Computer Modeling. Introduced as an aid in predicting multipath interference sources on an ILS performance. b. Para 1-14 Interlock. Requirements clarified. c. Para 1-15 Critical Areas. Clarifications, adds flexibility, reduces areas behind and adjacent to unidirectional localizer antenna arrays. d. Para 1-16 ILS Shelters. Provides criteria regarding size and material. e. Para 2-4 Antenna Descriptions. Updated antenna types to those currently available. f. Para 2-5 Localizer Siting Requirements. Clarified minimum distance criteria and revised antenna height guidance. g. Para 2-7 Abnormal Case Modulation. Documents the 60 percent maximum requirement on received localizer modulation. h. Para 3-2 Glide Slope Antenna Array Types. New section describing relative siting considerations for the various glide slope antenna configurations. i. Para 3-7 GS Location. Updated to new lateral distance criteria with distinction between Cat I and Cat II/III. j. Para 5-1 Remote Status. Updated to include remote status requirements on all categories of ILS and the limited role of Remote Maintenance Monitoring (RMM).
k. Appendix 4 RDH/ARDH Considerations. Flight Inspection measurements and their impact on glide slope threshold crossing height.
1-5. APPLICATION
The criteria set forth in this Order apply only to new establishments or relocated ILS facilities to include Localizer, Glide Slope, Marker Beacon, Localizer Type Directional Aids, and Offset Localizers. Additional criteria are presented for Non-Directional Beacon and Distance Measuring Equipment specific to collocation with ILS facilities. Changes to existing facilities for the sole purpose of obtaining compliance with these criteria are not required but are acceptable.
1-6. DIRECTIVE VERBS
1-6. DIRECTIVE VERBS
The material in this Order contains FAA criteria, recommended practices, and other guidance material, which require the use of certain directive verbs such as, MUST, SHOULD, WILL, and MAY. In this Order the explicit meaning of the verbs is as follows:
a. MUST. The action is mandatory. For example: “The localizer station MUST automatically shutdown if the monitor detects an out-of-tolerance condition."
b. SHOULD. The action is desirable or recommended. For example: “The glide slope SHOULD be located 400 feet from the runway centerline."
c. WILL. The action is to be taken in the future. For example: "Some facilities WILL be programmed for upgrading to provide Category II performance.
d. MAY. The action is permissible. For example: “Parking of unattended vehicles or aircraft within this area is prohibited at all times, except for maintenance technician vehicles, which MAY be parked adjacent to the equipment shelter."
1-7. PROCEDURES
1-7. PROCEDURES
a. Safety. Personnel must use caution in working on ILS equipment, particularly radio transmitters, since the voltages presented are dangerous to life. Observance of precautions necessary to avoid electrical shock is the direct responsibility of the individual. No one must perform work on the equipment without full knowledge of the dangers involved. An individual should not attempt work on high-voltage circuits without the services of an assistant.
b. Standards and Tolerances. The standards and tolerances for the ILS are contained in Order 6750.49Maintenance of Instrument Landing Systems (ILS) Facilities, and the applicable instruction books. Note that for installation purposes, the initial tolerance must apply.
c. Airborne Performance Requirements. The airborne requirements in this Order are based on information available at the time of publication. FAA Order 8200.1 continues to be the final source for current airborne performance requirements.
NOTE: See Appendix 1 for glossary and acronyms.
1-8. INTRODUCTION
1-8. INTRODUCTION
a. ILS Function. The ILS provides guidance to pilots of properly equipped aircraft to assist them in landing safely under conditions of reduced ceilings and lowered visibility. The use of an ILS materially aids the service to airports under all weather conditions.
b. Categorization of ILSs. The ILS is categorized according to the minimum visibility conditions under which aircraft landings are permissible. The criteria specified in this Order apply to Category I, Category II, and Category III systems.
c. ILS Siting and Installation. The goal of the ILS installation is to provide an allweather ILS that, with the possible use of ancillary equipment, will provide information sufficient to guide the aircraft down to the runway and along the runway surface regardless of weather conditions. The ability to attain this objective depends to a great extent on the proper siting and performance of each ILS subsystem.
1-9. ILS ESTABLISHMENT CRITERIA
1-9. ILS ESTABLISHMENT CRITERIA
a. ILS Establishment Assignments. ILS establishment assignments are made by the Washington office from regional office selections in accordance with the current ILS establishment policy. Assignments should be supported by a fully documented staff study, including a benefit/cost analysis. Consideration is also given to the reduction in the existing landing minimums, which an ILS will permit. At some locations other factors may preclude any improvement in the minimums; however, the assignment may be approved on the basis of the improved margin of safety provided by an ILS.
b. Runway Selection Considerations. The particular runway that the ILS will serve is selected in conjunction with the airport assignment. This choice is based on the following considerations:
(1) Runway length and width. (2) Compliance with the minimum obstruction clearance criteria. (3) Alignment with respect to the prevailing low visibility wind. (4) Orientation with respect to the traffic procedures of the airport and airway concerned. (5) Missed approach procedures.
c. Physical Requirement Considerations. The location of the electronic systems should be considered when making the ILS runway selection. It is impractical to designate a runway for the establishment of an ILS without giving consideration to the physical space requirements, accessibility, and the operating environment for each of the subsystems. When these factors appear to negate the establishment of an ILS, the cost of providing satisfactory facility locations should be weighed against the improvement in weather minimums, safety, and service that the ILS will provide. Siting within restricted areas should only be considered when standard installations are not practical.
d. Back-course Coverage Considerations. The newer localizer antenna systems, using uni-directional antennas, will not provide a useable back-course. If an instrument approach is required in that direction, other means should be considered, such as 1) a facing localizer on the opposite end of the runway, or 2) a 14-element V-ring array, or 3) procedures based on other type navigational systems, or 4) modification to the uni-directional Log Periodic Dipole (LPD) antennas.
e. Equipment Type and Configuration Considerations. Equipment type and configuration used in ILS establishments should be carefully chosen for the environment in which it is installed. Consideration should be given not only to siting ILS equipment to account for current terrain, obstructions, etc., but also for airport expansion and other developments around the airport environment. Type and configuration include single versus dual frequency equipment, narrow versus wide aperture antenna arrays, capture-effect versus null-reference, etc. An example is the airport where a single frequency, narrow aperture, localizer will function satisfactorily, but airport plans indicate a large hangar construction project. In this example, the siting engineer should consider siting a more complex localizer system to protect future facility performance. The glide slope example can be more demanding. If a null-reference glide slope is sited and subsequent changes to the airport environment require change to a capture-effect configuration, the modification to capture-effect could involve more than simply reconfiguring the transmitting equipment. Since a capture-effect configuration requires an additional antenna and mast height, the modification could actually require moving the glide slope site to allow adequate clearance of the Obstacle-Free Zone (OFZ). In this example, major issues in the future can be avoided with prudent siting.
1-10. ILS COMPONENTS AS OBSTRUCTIONS
1-10. ILS COMPONENTS AS OBSTRUCTIONS
The siting engineer considers the effects of the ILS components themselves as obstructions. These considerations should include guidance given in FAA Order 8260.3, 14 CFR Part 77, and applicable Advisory Circulars such as AC 150/5300-13, 70/7460-1. Both the Airport division office and Regional flight procedures office should be consulted and provide approval and/or waiver for any penetrations as part of the required airspace review. Failure to obtain approval or a waiver will preclude installation of that component.
1-11. NATIONAL AIRSPACE SYSTEM CHANGE PROPOSAL (NCP)
1-11. NATIONAL AIRSPACE SYSTEM CHANGE PROPOSAL (NCP)
If in the process of planning or locating the ILS facilities it is determined that the siting criteria set forth in this Order cannot be followed, an NCP must be submitted in conformance to the latest edition of Order 1800.66 National Airspace System Configuration Management. An NCP to the siting criteria should be submitted a minimum of 60 days prior to construction. The facility must not be commissioned without an approved NCP.
1-12. GENERAL DESCRIPTION OF THE ILS
1-12. GENERAL DESCRIPTION OF THE ILS
The ILS provides the aircraft with three basic types of navigational information as outlined below.
a. Lateral Guidance. Lateral guidance information indicates to the aircraft whether it is to the right, left, or aligned with the approach course line. The ILS localizer provides this information.
b. Vertical Guidance. Vertical guidance information indicates the aircraft position above, below, or along the proper descent angle towards the runway touchdown point. The ILS glide slope provides this information.
c. Distance Information. Distance information allows determination of the aircraft's approximate distance from the runway threshold. This information is provided indirectly by the ILS outer, middle, and inner markers and/or directly by installation and use of distance measuring equipment (DME) in conjunction with the applicable instrument approach procedure chart.
d. Additional Equipment. Additional equipments supporting the ILS include Supplementary Aids, Monitor and Control Equipment, and Remote Maintenance Monitoring.
(1) Supplementary Aids. Compass locators are sometimes provided at the middle or outer marker sites to assist the aircraft in locating the ILS course. Other types of navigational aids may also be used for this purpose. Approach lighting systems with sequenced flashers and other visual aids are usually provided to work in conjunction with the ILS.
(2) Monitor and Control Equipment. Each ILS component is continuously monitored at the site with automatic equipment provided to shut down the facility if the signal parameters exceed established limits. Remote status indicators, located at a manned Air Traffic (AT) monitoring location, provide air traffic control (ATC) personnel with an indication of the system status at all times except when the status unit is located in a facility that is not manned 24 hours per day. At these locations, the ILS continues to operate, but the particular airport cannot be designated as an alternate flight terminus during the period of time the ILS components are not being remotely monitored. At some locations, remote control equipment is also provided to turn the equipment on and off from the remote monitor point (see Paragraph 5-1).
(3) Remote Maintenance Monitoring. Some ILS equipment provides for remote maintenance monitoring (RMM) capabilities, which allow the maintenance technician to perform most maintenance tasks remotely via a computer (see Paragraph 5-1.d). The RMM equipment can either be built into the ILS equipment, or may be retrofitted to existing ILS equipment (e.g., airport remote monitoring system – ARMS). Most RMM systems are designed to connect with the maintenance processor system (MPS) equipment. RMM does not fulfill the Air Traffic requirement regarding remote status and control capabilities. Typical RMM equipment will include environmental sensors.
1-13. SITING EFFECTS ON ILS OPERATIONS
1-13. SITING EFFECTS ON ILS OPERATIONS
The ability of each subsystem that comprises the ILS to provide reliable and accurate guidance information depends primarily upon the proper formation of its respective radiation patterns. The greatest detriment to the formation of the desirable patterns is the presence of reflecting objects such as uneven terrain, power lines, buildings, dense vegetation, ground vehicles, water,
snow, and ice conditions, and aircraft moving in the vicinity of the sites. The following siting requirements for each type of facility should enable the responsible engineer to choose the optimum site. Math modeling techniques can be employed to predict the probable location, magnitude, and duration of ILS disturbances caused by multipath conditions, whether from structures or from aircraft of various sizes and orientation at different locations. Issues involved with these techniques are outlined below.
a. Computerized Math Models. Computerized math models are widely available and usable by personnel with a wide variety of experience levels; however, engineering knowledge of and judgment about the appropriate assumptions and limitations of the various models are required when applying such models to specific multipath environments. It should be noted that modeling results do not consider other operational issues such as snow banks, aircraft or vehicular movement, aircraft hold areas, or increase to aircraft taxi times due to ILS critical areas. Additionally, the modeling tends to simplify the topography and surrounding environment.
b. New Facility Math Modeling. For new siting, and particularly for challenging siting conditions, siting engineers with little modeling and validating field experience should be cautious about performing their own modeling. It is recommended that these engineers seek modeling assistance from the FAA Technical Center, outside engineering sources, or other more experienced FAA engineers for peer review of modeling results before making siting recommendations (see Appendix 2, Paragraph A2-2).
c. Existing Facility Math Modeling. Where an ILS has been installed and found satisfactory, computers and simulation techniques can be employed to predict the probable extent of ILS disturbance, which may arise as a result of proposed new construction. Wherever possible, the results of such computer-aided simulation should be validated by direct comparison with actual flight measurements of the results of new construction. Again, it is recommended that the engineer with little modeling and validating field experience should seek modeling assistance from the FAA Technical Center, outside engineering sources, or other more experienced FAA engineers.
1-14. MULTIPLE ILS ESTABLISHMENTS
1-14. MULTIPLE ILS ESTABLISHMENTS
When planning ILS establishments (full or partial) for airports already having one or more commissioned systems, consideration is given to the compatibility of the multiple systems, in addition to their individual compliance with the standard siting criteria (see Figure 1-1). This compatibility is assured to a great extent by assignment of non-interfering frequencies and distinctly different identification codes, and the development of standard instrument approach procedures for each of the multiple systems. When identical frequencies are used, or interference effects are encountered, an interlock system is also required.
a. Interlock requirements for multiple establishments. The installation of multiple ILSs at an airport may require an interlock system to prevent simultaneous radiation.
(1) Interlock System Requirements. An interlock system is required when:
(a) Two ILSs (full or partial) share a common frequency, regardless of runway geometry. The interlock is required to prevent destructive interference from simultaneous co-channel operation of the localizers and glide slopes.
(b) Facing localizers, on common or dissimilar frequencies, are installed on a common runway (see Figure 1-1B). The interlock is required to prevent destructive interference or aircraft receiver cross modulation effects during over flights, and must be installed and used to deactivate the localizer that serves the inactive runway.
(c) Interference effects, typically from aircraft receiver cross modulation, are encountered from other than co-channel or facing ILS facilities. Interlocking of these facilities is required on a case-by-case basis, based on frequency modeling, confirmed user reports, or flight inspection results (see Figure 1-1C).
(2) The interlock system must be:
(a) Remotely controlled.
(b) Interlock Activation Delayed. The ILS interlock system must have a 20-second (minimum) time delay for control point commands. This delay is from the time the active ILS shuts down to the time the newly selected ILS activates.
(c) Failsafe Designed. Failure of any interlock component to include the interfacility connection must ensure equipment shut down or no change in radiating status.
(3) Temporary override of interlock systems. Interlocked ILSs must not be active at the same time except when work is actually being performed and NOTAMS issued to properly address the possibility of hazardously misleading information (HMI). An interlock system must be utilized (refer to FAA Order 6750.49A, Paragraph 1-16) for operational conditions and requirements. Typical reasons for simultaneous operation include facility installation, maintenance, or flight inspections.
b. Non-interlock requirements for multiple establishments. In addition to any interlock requirements, consideration is given to simultaneous operation of markers for parallel approaches (see Figure 1-1A). The outer markers serving parallel runways, whether staggered or abeam of each other, are not always separated sufficiently to preclude interference at altitudes intended for use. If interference is unavoidable, the keyed identification of the two markers must be synchronized by the use of a single common keyer, and the operating frequencies must be separated by 8 kHz (i.e., 75.004 MHz. and 74.996 MHz). There are no additional criteria for the middle or inner markers in a parallel approach configuration, since the respective patterns at lower heights are non-interfering.
2/14/2005
0
LOC
Rwy 18 Approach Slope
Loc #1
Loc #2
GS #2
Potential Overflight Interference Area
Chap 1
6750.16D
⇐ Approach 36R
⇐ Approach 36L GS MM
A. PARALLEL APPROACH SYSTEMS OM
A. PARALLEL APPROACH SYSTEMS OM
Potential Interference Areas Rwy 36 Approach Slope
RWY
GS #2 GS #1 Loc #2
B. FACING SYSTEMS
GS #1 GS #1
GS #2 Potential Crossflight Interference Area
Loc #2 Loc #1 Loc #1
C. ADJACENT & CROSSING RUNWAYS
Figure 1-1. Multiple ILS Configurations
1-15. ILS CRITICAL AREAS
1-15. ILS CRITICAL AREAS
a. Definition. A critical area is a specific ground area near a radiating localizer or glide slope antenna array, which must be protected from aircraft and vehicle parking and the unlimited movement of surface and air traffic, to ensure the continuous integrity of the signal received by the user aircraft.
b. Application. The critical area is intended to protect the ILS facility from moving and stopped aircraft and vehicles, and does not apply to stationary objects whose permanent effects on the signals have been flight inspected.
(1) Evaluation of Permanent Objects. The possible deleterious effects of permanent objects planned for placement in the critical area should be analyzed and/or mathematically modeled prior to construction. If this is not possible prior to construction, a confirming flight inspection must be conducted to determine the effects, if any, on the ILS subsystems. Note that placing an object outside the critical area does not guarantee non-interference with the ILS signal in space.
(2) Critical Area Dimensions. Critical area dimensions have been determined for the different facility antenna configurations and categories of operation by mathematical modeling and empirical validation using various sized aircraft. For a particular localizer or glide slope installation, the critical area must be marked/signed according to the worst-case condition feasible in that portion of the overall critical area, i.e., Aircraft holdlines on taxiways may be more restrictive than those critical area signs installed to restrict access of mowers or maintenance vehicles.
(3) Critical Area Size Considerations. Critical area sizes need not be considered fixed for a particular localizer or glide slope. For example, although a 747 aircraft may routinely taxi near a glide slope, which has been marked for an appropriately large critical area, a grass mower, which has a much smaller profile, can penetrate the outer portions of the large (aircraft) critical area without significant effect. In this case, the mower need only remain outside the critical area boundaries defined for a small aircraft. FAA provided signage must be installed accordingly and maintained to control this smaller critical area from the penetration of surface vehicles.
(4) Allowance. Allowance can be made on a temporary basis to permit penetrations of the critical area based on engineering decisions (which may include modeling) regarding the specific vehicles and operations, with appropriate controls imposed.
(5) Longitudinal Axis. Critical area dimensions are based on the assumption that the entire longitudinal axis of the aircraft is clear of the critical area. For the purposes of this assumption, an aircraft whose longitudinal axis lies on the boundary of the critical area (e.g., where a taxiway centerline coincides with the critical area boundary) is not considered to be violating the critical area.
c. Localizer Critical Area. The critical area dimensions and the corresponding protection requirements depend on several factors. These include size and orientation of interfering parked or
moving aircraft and vehicles, localizer course width, category of operation, and antenna directional characteristics.
(1) Localizer critical area dimensions are defined in Figure 1-2.
(2) Installation of the localizer antenna system on an elevated platform does not negate the requirements of the critical area.
(3) Localizer installations for public Category II or III approaches are not authorized using single frequency antenna arrays, as the critical areas become too large to feasibly protect.
d. Glide Slope Critical Area. As in the case of the localizer, the size of the glide slope critical area is affected by several factors including type of radiating array, category of operation, and size and orientation of interfering parked or moving aircraft and vehicles.
(1) The critical area for image glide slopes is identified in Figure 1-3.
(2) The critical area for endfire glide slopes is shown in Figure 1-4.
e. Critical Jet Blast Areas. In addition to safeguarding the ILS guidance information from surface traffic interference, the system must be protected from long term deterioration resulting from accumulation of jet engine exhaust residue. Therefore, jet aircraft must not be permitted to operate with its jet exhaust directed toward the facility, within 600 feet of the ILS equipment shelters, the localizer antenna array, or the glide slope antennas. This distance is measured from the individual ILS component to the nearest aircraft engine.
f. Restrictions. Although it is desirable to completely restrict the critical areas from all surface traffic, this is generally not feasible since access to and from the runway, terminal areas, ramp, and hangar areas may necessitate traffic movement through these regions. The restrictions must therefore be sufficiently permissive, as delineated in the following subparagraphs, to permit this traffic flow under controlled conditions.
(1) Surface Traffic. Except as provided below, and in the latest edition of Order 7110.65, Air Traffic Control, all surface traffic must remain clear of the localizer and glide slope critical areas whenever the equipment is in operation. Parking of unattended vehicles or aircraft within this area is prohibited at all times, except for maintenance technician vehicles, which may be parked adjacent to the equipment shelter.
(2) Non-Aviation Users. Where non-aviation users pass through the critical area and unacceptable degradation is expected from traffic movement along these routes (e.g., on roads, highways, railroad tracks, etc.), effective measures must be taken to overcome the condition. Such measures may include math modeling and/ or flight inspection (to determine the magnitude of the degradation), controlling traffic along the route, or elevation/ relocation of the antenna array.
(3) Maintenance Vehicles. Maintenance vehicles may pass through the critical area
along access roads when traveling to and from the equipment shelter, provided they do not stop and
the route does not pass in the immediate vicinity of the antenna.
g. Vegetation Control. Lease agreements should contain provisions to control
vegetation growth. Vegetation should not be permitted to exceed 12 inches in height in the ILS
critical areas within 2000 feet of the localizer and 800 feet of glide-slope antennas. Action must
be initiated when observed vegetation growth exceeds this height. Growth of crops of any type
must not be permitted. Mowing operations should be coordinated for a time to coincide with
scheduled facility maintenance.
Area A Area B Taxiway
501 Holding Line Note 3
45° Localizer Antenna Array 250 Radius ILS Runway 45°
X
X Y Category ! 2000 400 Note 4 Category II/II 2000 400 Note 5 Category II 4000 500 Notes: Category III 7000 500
1. Critical area is indicated by shaded zones. 2. Hold line/signs indicate the position beyond which aircraft/vehicles will require ATCT authorization before proceeding on or across runway. 3. Area B is deleted from the critical area when a unidirectional localizer antenna is installed. The standard log-periodic dipole antenna array is in this category. 4. For 8-element localizer array with course widths less than 4 degrees and runways which operate B-747-size and larger aircraft, the Y dimension shall be 600 feet. 5. These dimensions apply where aircraft size is equal to or less than 135 feet in length or 42 feet in height; e.g.. B-727. 6. Critical areās for LDA, SDF, and Offset Localizer facilities are the same as for Category I, but are centered about the course line.
Figure 1-2. Category I, II, & III Localizer Critical Area
- ILS Runway
L E F Notes. 1. The critical area is defined by the pentagon EFGHJ
200' to 50→ 2. All aircraft may be parked as close as 50 feet behind a glideslope mast with directional antennas as defined
650' GS Ant. by line "KL".
Mast
V J 35° G K H -X
V J 35° G K H -X
Not To Scale
FACILITY TYPE CATEGORYI CATEGORY II/II X X Y ALL IMAGE GLIDE SLOPES Small Aircraft 2/ 800 100 800 100 NULL REFERENCE Medium Aircraft 3/ 2000 200 2500 200 Large Aircraft 4/ 3100 200 3200 200 SIDEBANDREFERENCE & CAPTURE EFFECT Medium and Large Aircraft 3/ 4/ 1300 200 1300 200
Notes: 1. All distances are in feet and represent the minimum allowable distances from the nearest point on the aircraft longitudinal axis (line from nose to tail) to the glide slope antenna, as defined in figure 1-3.
2. Small aircraft are defined as aircraft with dimensions less than 60' in length and 20' in height; i.e., Kingair. This includes all surface vehicles and helicopters.
3. Medium aircraft are defined as aircraft with dimensions less than 160' in length and 38' in tail height; i.e., B-727, MD-80.
4. Large aircraft are defined as all aircraft greater than 160' in length or greater than 38' tail height.
5. The small. medium and arge aircraft sizes are based upon the dimension used in computer modeling of critical are as and apply to this document only.
Figure 1-3. Image Glide Slope Critical Area
A B
ILs Rurway
50' F
E Note 1 CLR Ant. Single Note 2 Mon. Rear Ants. Ant. Front Ant. Phase Center G 50' H GS Shelter
Taxiway
150o' or to the end of rurway (whichever is less)
Notes: 1. This distance is approximately 200 feet depending onrunway width. Refer to FAA drawings D-6226-1 and D-6226-2 for installation layout. 2. This distance shall not be less than 25 feet. 3. The critical area is defined by the area "ABCD". Unrestricted taxiing or holding aircraft is permitted in unshaded area. 4. Snow removal area"EFGH".
Figure 1-4. End Fire Glide Slope Critical Area
h. Implementation. Effective implementation of the critical area restrictions requires a coordinated effort by several regional and field offices as follows:
(1) Airport Management. Advise airport management authorities of these criteria and request that they provide and maintain the necessary signs, holding lines, and other markings delineating the critical areas. In addition, new establishments should be planned to avoid critical area encroachment of existing runways and taxiways if possible. (See latest edition of Advisory Circular 150/5340-1, Standards for Airport Marking, Marking of Paved Areas on Airports, for marking information.)
(2) Airway Facilities. When advised by Air Traffic that the implementation of this Order impacts airport operations or capacity, Airway Facilities should request assistance from the regional and national office to obtain site-specific math modeling or flight inspection of any proposed reduction in critical area dimensions.
(3) Air Traffic. Where an ATCT is in operation, and the airport management has provided the required markings and signs, tower personnel will not clear aircraft or vehicular traffic into the ILS critical areas, except as provided in Paragraph 1-15f, in accordance with FAA Order 7110.65, Air Traffic Control, FAA Order 7210.3 Facility Operation and Administration, and applicable letters to airmen and letters of agreement.
(4) Aviation Standards. Conduct flight checks to ascertain whether the exceptions under Paragraph 1-15f are permissible.
1-16. ILS SHELTER STANDARDS
1-16. ILS SHELTER STANDARDS
ILS shelters are allowed in the runway vicinity by exception to typical building restrictions on airports. As such, ILS shelters should be reasonably limited in size and mass to minimize risk.
a. ILS shelters within designated Object Free Areas or Safety Areas must be limited to a size required to provide for the intended function.
b. Concrete shelters must not be used for ILS facilities within airport operations area (AOA). c. Shelters located off airport include security fencing.
d. ILS facilities must be painted and marked in accordance with Advisory Circular 70/7460-1.
1-17. RESERVED
1-17. RESERVED
CHAPTER 2.THE ILS LOCALIZER
2-1. GENERAL DESCRIPTION
a. Channel Assignments. ILS Localizers operate on one of 40 channels within the frequency band of 108 to 112 MHz. Individual channel assignments are made in accordance with frequency management procedures. Each localizer is assigned a four-letter identification code: an “I", to distinguish the ILS from other navigational aids, followed by a three-letter code, which identifies the particular ILS. The identification is accomplished by modulation of the localizer transmitter with a 1020 Hz tone keyed in accordance with the assigned four-letter code, at the rate of approximately eight identification signals per minute. Where DME is used in conjunction with the ILS, every fourth localizer identification signal is used to key the DME transponder.
2-1. GENERAL DESCRIPTION
b. Localizer Course Guidance. The localizer course guidance information is provided by the modulation of the transmitted signal with audio signals of 90 Hz and 150 Hz. The antenna radiation pattern is designed so that the 150 Hz signal is predominant to the right side of the front course approach, and the 90 Hz signal is predominant to the left of the approach. The localizer course itself is a theoretically straight, but in reality it is formed by the locus of the points where equal levels of 90 and 150 Hz signals are received and detected by the aircraft. The localizer course is usually adjusted to coincide with the runway centerline and centerline extended. The course may lie in two directions, forming both a front course and a back course; however, the back course localizer is the exception and is not provided unless essential from an operational standpoint. Localizer antenna systems, which provide bi-directional radiation, should not be installed unless the back-course approach is to be commissioned.
c. Localizer Receiving Equipment. The localizer receiving equipment generates a meter deflection indication, which corresponds to differences in depth of modulation. When the aircraft is on course there will be a zero-centered meter. When the aircraft is left side of the course, the Course Deviation Indicator (CDI) needle will deflect to the right and when the aircraft is right side of the course, the needle deflects to the left. The CDI is calibrated so that 150 micro amps (.155DDM) represent full-scale deflection on each side of the course centerline. The angular value corresponding to the 150-0-150- micro amp values is defined as the course width. The standard or “tailored" course width provides for 700 feet between the full-scale deflection points at the runway threshold. When the localizer antenna to threshold distance is less than 6678 feet, the course width is capped at a maximum of 6.0 degree. Localizers used for Category I service only may be “non-tailored" if necessary within the limits of 6.0 degrees maximum and 400 feet at threshold minimum. Localizers supporting Category II/III service must be “tailored."
NOTE: Where the Localizer course is offset from runway centerline, the alignment and width measurements are relative to the localizer course rather than the runway centerline.
d. Clearance Signal Sectors. In areas beyond the course width limits, the clearance signal sectors are defined (with respect to the localizer front or back-course on each side) as follows for the purpose of establishing minimum clearance requirements:
Sector Defined Area Minimum Normal Clearance 1 ± 10° Linear increase to 175μA and maintain at least 175μA 2 ± 10°to ± 35° 150 μA
NOTE: With the course width broadened to monitor limits, a 15 micro amp reduction is permissible. Additional momentary deviations to as low as 100 micro amps may be permissible (see FAA Order 8200.1, the United States Standard Flight Inspection Manual for guidance.
e. Straight Line Course. It is also highly desirable for the localizer course to be a straight line, which coincides with the runway centerline extended to permit maximum use of automatic approach equipment (see Figure 2-1). In addition to increasing the difficulty of a manual approach, severe course aberrations such as roughness, scalloping, or bends may preclude the use of automatic approach equipment. Departure of the actual localizer course from a theoretical straight line will, to some extent, determine the landing minimums. The permissible course displacement varies with the distance from runway threshold and is tabulated in Section 217 of FAA Order 8200.1.
4 nmi 2000 3000 3500
Point A End of Runway Point B Point C Point E Point D Threshold 12 Extended Glide Path 100
Notes:
Point A is located on the glide path 4 nautical miles outbound from the runway approach threshold, measured along the runwãy centerline extended (or the localizer approach azímuth).
Point B is located on the glide path 3500 feet outbound from the runway approach threshold, measured along the runway centerline extended (or the localizer approach azimuth).
Point C is located at the intercept of the downward-extended straight portion of the glide path (at the commissioned angle), the verticle plane containing the runway centerline extended (or the localizer approach azimuth), ánd the horizontal line 100 feet above the horizontal plane containing the runway threshold.
Point D is a point 12 feet above the runway centerline and 3000 feet from the threshold in the direction of the localizer.
Polnt E is a point 12 feet above the runway centerline and 2000 feet from the stop end of the runway in the direction of the threshold.
Figure 2-1. ILS Course Displacement Reference Points
Power Lines
Water and Fuel Highways and Storage Tanks Railroad Tracks
Localizer
LS Runway ExtendedRunway Centerline
Large Hangars and Buildings
Bi-Directional Direct Signal Arrays Reflected Signal
Figure 2-2. Typical Localizer Degrading Sources
f. Low Clearance Areas. The principal cause of localizer course deviations and low clearance areas is the distortion of the antenna system radiation pattern by signal reflections from nearby objects such as hangars, power lines, vehicular traffic, wire fences, and buildings (see Figure 2-2). It may not be possible to remove these objects from the area; however, by judicious siting of the localizer antenna system, the effects of the degrading sources may in many cases be minimized. The use of math modeling as an engineering tool is recommended during these types of siting activities (see Paragraph 1-13). Unidirectional arrays are much less sensitive to reflecting sources behind them. Little significant energy exists beyond 50 feet to the rear of these arrays.
g. Standard Service Volume. The localizer Standard Service Volume (SSV), which is required to have a minimum receiver input signal level of five microvolts, in addition to the minimum flag current and clearance signal requirements, is measured with the transmitter power reduced to the monitor alarm level. The minimum coverage requirements are 18 nautical miles (NM) within clearance sector 1 and 10 NM within clearance sector 2. Vertical coverage is required below line 7 degrees from horizontal (referenced at the localizer antenna) to 4500 feet above site elevation.
2-2. LOCALIZER LOCATION AND TYPES
2-2. LOCALIZER LOCATION AND TYPES
a. Localizer Equipment. The ILS localizer consists of an antenna array, electronic equipment, integral detectors, and an equipment shelter. Category II and Category III localizer systems also include a far field monitor (FFM), which is sited near the inner or middle marker or both. The localizer is normally located near the stop end of the runway. The antenna array is the prime consideration and will, to a certain extent, fix the location of the shelter.
b. Antenna Systems. There are several types of FAA-procured localizer antenna systems in present use. The more familiar ones are the V-ring, and the log-periodic dipole antenna. The V-ring array is essentially bi-directional and was formerly the FAA standard system, whereas the other types are unidirectional systems originally used to overcome V-ring siting problems caused by reflecting objects. The criteria contained in the following paragraphs apply generally to all systems. A more thorough description of each system is given in Paragraph 2-4.
3.0° Maximum
Localizer Array
Offset Angle - 3.0° Maximum
ILS Runway Extended Runway Centerline
1150' +1-50 Localizer Course Line
Notes: 1. See TERPS handbook for the lowest permissible landing minimums for a full ILS with an offset 2. Markers, if required, should be established in localizer. accordance with current criteria using the localizer course line rather than the extended runway centerline as the reference line. Locae ie way
Figure 2-3. Offset Localizer Configuration
2-3. LOCALIZER EQUIPMENT SHELTER
2-3. LOCALIZER EQUIPMENT SHELTER
a. Centerline Localizer. The localizer electronic equipment shelter must be located a minimum distance of 250 feet from the center of the runway and should be within 30 degrees of the longitudinal axis of the array. When a V-ring antenna system is used, it is preferable to locate the shelter in the minimum signal area that exists at 105 degrees from the front course line and at the above distances. The maximum distance to the building is limited by the attenuation of the antenna feed lines. The building may be situated on either side of the antennas depending on the local terrain, access roads, and power line connections. The criteria for location of the shelter must apply to both permanent buildings and portable shelters (see Paragraph 1-16 of this Order for shelter information).
b. Offset Localizer/ LDA. The equipment shelter must be located outside the runway/ taxiway safety areas, no closer than 250 feet from centerline extended, and must not be located in critical area (see to Figure 1-2).
c. Platform Mounted Arrays. If an elevated array is installed, the shelter may be located directly behind the platform, provided the elevation of the top of the shelter does not exceed the level of the platform.
2-4. DESCRIPTION OF THE ANTENNA SYSTEMS
a. Single-Frequency Arrays. Single-frequency arrays operate on the assigned carrier frequency and are used for Category I operations.
2-4. DESCRIPTION OF THE ANTENNA SYSTEMS
b. Dual-Frequency Arrays. Dual-frequency arrays operate on two frequencies, with the course signal on a carrier frequency offset 4 KHz above the station frequency and a clearance signal offset 4 KHz below the assigned station frequency. This frequency difference is within the receiver's pass-band so the AM-detector principle determines what signal (typically stronger) is captured (used). The course distribution is designed to confine the radiation near the runway centerline and the clearance signal is designed to provide the fly-left, fly-right guidance in the clearance sector.
c. Unidirectional antenna Arrays. Unidirectional antenna arrays are designed to provide coverage to ±35 degrees on the front course and typically use the log periodic dipole antenna (LPD). The LPD antenna incorporates integral monitoring and has a nominal front-toback radiation ratio of 28 dB. The horizontal beam-width is 45o and signal beyond the coverage sector is greatly reduced. The LPD antenna is used for both the single-frequency arrays and dual-frequency arrays. The table below lists the various combinations of antenna array distributions.
Table 2-1. Localizer Antenna Arrays
Number of Antenna Elements Frequency Aperture Size(s) (ft) 8 Single 45,50
14 Single 86,100 14 Dual 86, 100, 126 20 Dual 150
14 Single 86,100 14 Dual 86, 100, 126 20 Dual 150
d. Bi-Directional Antenna Arrays. Bi-Directional Antenna Arrays provide a useable back-course. Two examples are as follows:
(1) V-Ring Array. The directional radiation pattern of the V-Ring array is obtained from a system of eight or fourteen antennas. The individual V-Ring antennas have a front-to-back pattern ratio of about 6 dB and have a broader beam width than the LPD antenna. Off-course reflections will be of higher amplitude for these arrays as compared to an LPD array.
(2) Modified Log Periodic Dipole. A modification was developed for localizer LPD antenna elements in order to reduce the front-to-back ratio of the LPD antennas from 28 dB to about 12 dB without significantly compromising front course horizontal pattern and signal strength. This results in lower amplitude reflections and less roughness and scalloping as compared to V-ring antenna arrays. The trade-off, due to the sharper array pattern, is typically procedural restrictions beyond 20 degrees each side of the back-course centerline. A modification authorization can be requested through the National Airspace System Change Proposal (NCP) process.
2-5. SITING REQUIREMENTS a. Localizer Antenna System. The localizer antenna system must be symmetrically positioned about the extended runway centerline (or approach azimuth for offset or Localizer Directional Aid (LDA) configuration) with the longitudinal axis of the array perpendicular to the runway centerline (or approach azimuth). The optimum distance from the stop end of the runway to the localizer array for each site must be determined by consideration of several factors:
(1) Required obstruction clearance criteria.
(2) Usable distance and signal coverage requirements.
(3) Presence of reflecting or reradiating objects in the vicinity.
(4) Safety considerations and the Runway Safety Area (RSA).
(5) Anticipated facility upgrading and/or airport expansion.
(6) Establishment costs.
b. Minimum Antenna Distance from Runway Stop End. Minimum antenna distance from the stop end of the runway to the localizer array should consider the distance, which precludes penetration of the approach plane surface (Federal Aviation Regulation, FAR Part 77), TERPS surfaces, the RSA, the light plane of a Cat II/III system. The obstruction requirements to all approach lighting systems should be met. For centerline extended localizer antennas, the minimum distance from the stop end of the runway must be the greater of 600 feet or the end of the runway safety area. All points of the localizer array must remain outside the runway safety area. Additional criteria pertaining to the minimum distance requirements are as follows:
(1) When a cleared and graded area extending from the stop end of the runway a distance of 1100 feet or more can be provided, the localizer array must be located beyond 1000 feet from the stop end of the runway.
(2) To assure protection from the effects of aircraft engine jet blasts, the minimum distance a localizer must be located from the end of a runway where jet aircraft are in operation, not precluding RSA requirements of Advisory Circular 150/5300-13, must be 600 feet. Where siting conditions preclude adherence to the 600-foot limitation, consideration will be given to locating the array beyond the maximum standard distance, to an offset location, or inside this limitation with adequate protection to personnel and equipment.
(3) Locating localizer arrays inside the RSA is permissible when the array is frangible at or below 3 inches, 14 CFR Part 139.309 (4), either by design or application of approved frangible bolt couplings at the base of the array.
c. Maximum Standard Distance from Runway Stop End. The maximum standard distance from the stop end of the runway to the localizer array is 2000 feet; however, location of the array beyond this distance is permissible where significant advantages can be obtained.
(1) When the localizer will serve a relatively short runway requiring a wide course width (5 to 6 degrees) to provide the 700-foot tailored width at threshold, the array may be located beyond the 2000-foot distance.
(2) Location of the localizer beyond the 2000-foot limit is permissible when airport expansion includes a runway extension, which would necessitate future localizer relocation. Planned taxiway and building construction should also be considered in this regard.
d. ILS Category II/III Localizers. ILS Category II/III localizers must be located on the runway centerline extended. When planning a CAT I ILS and the potential for future upgrading to Category II/III operation exists, consideration should be given to the CAT II/III requirements.
e. Elevation. The elevation of the array must be considered in conjunction with the distance requirement. Although a ground-mounted array is usually adequate at most facilities, at some locations an elevated array may be necessary to provide the required minimum signal
coverage and performance. This may occur where runway discontinuities exist (humps, elevation changes, or runway safety area grading) or the presence of hills, trees, buildings, or other obstructions in the vicinity cause a shadow effect. As an elevated antenna structure on the extended runway centerline is quite massive, other options should be considered to include placing the antenna on additional fill or moving the antenna array to a higher elevation within the runway safety area.
(1) Antenna Height. The array should be mounted so that the antennaradiating element is in line of sight with threshold crossing height (TCH) at the approach end of the runway. With the lower minimums and more stringent tolerances associated with Category II/III sites it is more essential to satisfy these criteria. At those locations where future upgrading to Category II/III is not programmed or considered feasible, i.e., runway length/width, presence of obstructions, annual instrument approaches, etc., the array may be mounted to provide line-ofsight to a point 100 feet over the threshold. This should be done after a complete site analysis has been completed that indicates satisfactory facility performance can be obtained with the lower antenna height. In the localizer frequency band, VHF propagation techniques may be used to find the usable distance for any given site and antenna height.
(2) Vertical Radiation Pattern. The vertical radiation pattern must be considered when installing an antenna array on a platform or on a rise significantly above a defined reflection ground plane. With increased elevation above the reflection ground plane, the angle of the first vertical null (or minimum) of the antenna array lowers. The upper limit of the standard localizer service volume extends to 7 degrees above the antenna elevation. It is imperative that a null not pass through the service area of the localizer system, as reflections will likely cause unacceptable aberrations due to the decrease in direct signal strength. The first vertical null is of special concern in the siting of localizer antenna arrays close to the approach end of the runway or for use as a back-course, particularly when minimums are relatively high and the missed approach point is relatively close to the facility. Localizer elements at a height of 35 feet above the extension of a reflecting plane will produce a null at an angle of about 7.3 degrees above that reflection plane. By contrast, the first vertical null of a ground-mounted installation, with elements at approximately 7 feet above the extended ground plane, will be at approximately 39 degrees above the ground plane. The formula for calculation of the first vertical null is as follows:
θ= arcsin [490 / (F x H)]
where; θ = the angle of the first null relative to the ground plane (must be added or subtracted to the angle of the ground plane to achieve the null angle relative to horizontal. H= the height of the antenna elements above the ground plane in feet F= the localizer frequency in megahertz.
f. Specular Reflection. The presence of signal reflecting objects in the vicinity (see Figure 2-2), to include critical area concerns (see Paragraph 1-15), may place an additional restriction on the location of the localizer antenna system. By application of the principles of specular reflection, the areas that will be affected by the reflected signals may be predicted by
math modeling techniques available through the Office of Integrated Product Team for Navigation and Landing, HQ FAA Washington, DC.
g. Front Course Quality. The quality of the front course and clearance areas is the primary consideration when establishing the localizer and should not be compromised for the sole purpose of obtaining a usable back-course approach. Expenditure of additional funds to upgrade the back-course, even without degrading the front course, cannot generally be justified.
h. Terrain. The terrain between the antennas and the end of the runway should not contain severe irregularities or obstructions that may affect the localizer signal quality. Existing obstructions should be removed and, if possible, the area graded (see Figure 2-4). Minor terrain irregularities and isolated small objects close to the array will not usually affect the radiated signal quality. Clearing should be limited to the removal of large shadowing objects such as dense trees, shrubs, and hillocks from in front of the array and any significant signal reflectors in the vicinity of the array. It is suggested that modeling and flight test be applied to difficult sites before attempting to commission.
i. Cost Considerations. When a tentative antenna location (based on the signal coverage, obstruction criteria, and other requirements) has been chosen for a localizer, the establishment costs will be estimated. Items to be considered include the cost of installing power lines and control cables, where required; the cost of site grading or landfill; the cost of the antenna support (concrete slab versus elevated platform); and the cost of constructing site access roads. The exact location of the array should be the least costly site consistent with the required level of service.
j. Offset Localizers. At some runways, terrain may prevent the localizer antennas from being positioned on the extended runway centerline. Where this occurs, and landfill or tall supportive structures are impractical, the localizer antenna array may be offset so that the course does not lie along runway centerline but rather intercepts the centerline at a point determined by the amount of angular offset and the glide path angle. To be classified as an “offset localizer", this offset angle can be up to 3 degrees. When offset angles greater than 3 degrees are necessary, the facility must be classified as a “localizer directional aid" (LDA). The landing minimums prescribed for an offset localizer vs. a LDA are prescribed in the latest edition of FAA Order 8260.3, United States Standard for Terminal Instrument Procedures (TERPS). The localizer offset angle (see Figure 2-3) is formed by the vertical plane containing both the decision height point (DHP) and the point on the runway centerline that is 1150 +/- 50 feet inbound from the DHP (with the latter point also containing the localizer course line). The criteria for standard localizer facilities must also apply to offset localizers with the following exceptions:
(1) The antenna array should be offset in the direction that will offer the least signal interference from movement or obstructions.
(2) An offset localizer or LDA facility must be located outside the runway safety area.
(3) The distance from the runway centerline to the nearest element of the array must comply with the obstacle free zone (OFZ) criteria of AC 150/5300-13, Airport Design.
(4) The entire array must be located outside the applicable taxiway safety area as defined in AC 150/5300-13, Airport Design.
(5) The antenna array must be sited to provide vertical and horizontal clearance to taxiing aircraft on adjacent taxiways.
Area A Area B Direction of Approach 501
45° Runway 250 5* 400 Radius 5 45°
30°
Note 4 Shelter Note 4
Notes: 1. Areas A & B should be free of localizer interference sources (trees, buildings,fences, etc.)
2. Grading in Area A should have a negative gradient between 0.5% and 3.0% from runway centerline extended to the outer edges. This grading should be as symmetric as possible across runway centerline. Area B should be graded similar to Area Å for bi-directional or omni-directional arrays.
3. The size and configuration of Area A is applicable to all facilities. Area B may be deleted at facilities that have uni-directional antennas; i.e., unmodified Log Periodic Dipole arrays. 4. Refer to Paragraph 2-4
Figure 2-4. Typical Localizer Plot Layout and Site Grading Requirements
2-6. GROUND CHECK POINTS (SEE FIGURE 2-5.) To facilitate the establishment of the facility parameters and to provide reference points from which the parameters can be periodically verified, ground checkpoints must be established at each localizer facility. Because of the different types of localizer arrays and the unique terrain and siting conditions at each facility, it is not possible to specify the exact location and number of checkpoints. For the establishment of ground checkpoints refer to current version FAA Order 6750.49.
Localizer Array 3 4 ←2
T 350' TYP. ILS RUNWAY HRESHO ←1
T 350' TYP. ILS RUNWAY HRESHO ←1
L D 350' TYP.
V
3 4 2
1. Course Alignment Check Point 2. Course Width Check Point 3. Quadrature Phasing Check Point 4. Low Clearance Check Point
Figure 2-5. Localizer Ground Check Points
2-7. SITE EFFECTS ON LOCALIZER PERFORMANCE
a. Operating Environment Considerations. The quality of an ILS localizer course and clearance signals is to a large extent determined by the operating environment of the system. Environmental factors, which should be considered when siting a localizer facility, include large buildings (such as hangars and terminal complexes), power and tree lines, metallic fences, cylindrical structures (such as water towers and fuel tanks), and terrain. A thorough analysis will help determine the optimum antenna location within the defined limits and will permit an accurate prediction of the system's performance at a particular site. If it is not possible to make an accurate prediction of the system's performance from the information available, a request for mathematical modeling assistance should be submitted in accordance with Appendix 2, Paragraph 2-2.
2-7. SITE EFFECTS ON LOCALIZER PERFORMANCE
b. Theoretical Considerations. Analysis of site effects on a localizer system's performance requires a thorough theoretical knowledge of the system. Since this information is available elsewhere, this section provides guidance on anticipated performance based on the patterns of the antenna elements as well as the nominal CSB and SBO patterns.
(1) Antenna Element Pattern. Performance can be improved by the selection of the antenna element type. In general, the uni-directionality of the LPD antenna suppresses the energy outside the localizer service volume and behind the array. Whereas the V-Ring antenna
element has a broad pattern and signal behind the array, Figure 2-6 shows a comparison between these element patterns. Based only on the antenna element patterns, the LPD array would provide improved course guidance signal over the V-Ring array.
(2) SBO Pattern Comparison. Structure roughness is typically the result of the SBO signal being reflected back into the course line resulting in degradation to the minimum or SBO null for the course line. Figure 2-7 shows a comparison between the course transmitter SBO of various single- and dual-frequency arrays. Figure 2-7 shows the dramatic reduction in SBO signal between the 8 and 14 element single frequency arrays between 7 and 16 degrees offcourse – greater than 6 dB reduction in signal strength, as well as reduced signal strength at all other azimuths. All three of the dual frequency arrays show even more dramatic reduction in Course SBO signal levels, with extremely low SBO levels beyond 11.5, 10.0 and 7.0 for the 14/6, 14/10 and 20/10, respectively.
(3) Dual-Frequency Consideration (Course-to-Clearance Power Ratios). Degradation to the guidance performance in ILS Zone 4 or 5 (FAA Order 8200.1b, Figure 217- 1a) of dual-frequency arrays used for Category II/III operation is typically caused by reflections of clearance signals onto the course centerline. Newer localizer arrays provide additional immunity by tailoring the clearance signal to have little energy outside the clearance sector. If roughness is found, the clearance transmitter parameters can be adjusted to minimize the roughness.
(4) Single-Frequency Considerations (Abnormal Case DDM).
(a) CDI Normalization. When single-frequency arrays are used for installation on long runways, resulting in narrow course widths, the separate sideband components are greater than the carrier sidebands. Where this condition occurs, space modulation is greater than transmitter modulation thus resulting in the measured total modulation exceeding 40 percent (see Figures 2-8 and 2-9). Certain ILS receivers, mostly digital processing receivers, use algorithms, which expect the received total modulation (i.e., -sum depth of modulation or SDM) to be 40 percent throughout the coverage area and úse this value to normalize the calculated cross pointer deflection indicator (CDI). This normalization process reduces the CDI reading.
(b) Maximum Limit Requirements. Recent requirements have placed a maximum limit on the received SDM of 60 percent for new and relocated localizers. Those arrays in our current inventory that have the characteristic where received SDM may exceed 60 percent are the single frequency 8 and 14 element systems based on a 45 foot and a 86 foot aperture, respectively. Table 2-2 exhibits the narrowest course width at which these antenna arrays are modeled to achieve this tolerance. As modeling assumes perfect power and phasing, the practical limit for acceptable course widths of these arrays could be up to 0.50o greater. Ultimate acceptance is determined by flight inspection. Mitigation options include commissioning at a wider than tailored course width or a restriction of the localizer at and beyond those azimuths affected.
Table 2-2. Minimum Normal Course Width for Single-Frequency Localizer Arrays for which Greater Than 60 Percent Abnormal Case DDM will not occur
Type Array Array aperture (ft) 60 % SDM Width Worst-case Azimuth
8 45 3.63 29°
14 86 4.04 30°
(5) Low Clearance Areas. Low clearance areas (below 150 μA) usually are caused by the reflection of signals from one side of the radiation pattern into the opposite side (i.e., 90 Hz signal reflected into the 150 Hz sectors or vice versa), the extent of the clearance signal reduction varying inversely with the ratio of direct-to-reflected signal amplitude. Reflection problems may be resolved by selection of the optimum location of the antenna array and by altering or removing the reflection source. It is imperative that adequate clearances be obtained in sector 1. Full-scale clearances in sector 2 are also desirable but not mandatory if an additional navigational aid is available to guide the aircraft into the usable sectors.
2/14/2005
6750.16D
LPD vs V-Ring Element Radiation Pattern (dB)
330
320
310
300
290
280
270
260
250
240
230
220 210
Chap 2
340
200
0 350 10 20 30
40 10.0 50
200 60
70
80 LPD
90 V-Ring
90 V-Ring
100
110
120
130
140 150 160 190 170 180
Figure 2-6. LPD vs. V-Ring
2/14/2005
6750.16D
Localizer SBO Pattern Comparison
1
0.8
0.6 Reltd Sd Si Stgth 0.4 0.2 0 0
10 20 30
40
Offset from Centerline (degrees)
8SF
14SF14_614_10
Chap 2
Figure 2-7. SBO Pattern Comparison
20_10
2/14/2005
6750.16D
8-Element Array (45-foot Aperture)
5
0
-5
-10
-15 Norl Ll dB) -30 -20 -25
-35
-40
-45
Course Width 3.64
CSB SBO
CSB SBO
SDM
100
-80
60 40 To ll om
-20
-35 -30 -25 -20 -15 -10 -5 0 5 10 15 20 25 30 35
Azimuth Angle (deg.)
Figure 2-8. 8-Element Array (45-Foot Aperture)
Chap 2
14-Element Array (86-foot Aperture) Course Width 3.08
5 130 CSB 0
-5 -110
Level B) -15 -10 SBO -90
Nod Rrr -25 -30 -20 SDM -70 Tol l o%)
-35 -50
-40
-45 -30 -35 -30 -25 -20 -15 -10 -5 0 5 10 15 20 25 30 35 Azimuth Angle (deg.)
Figure 2-9. 14-Element Array (86-Foot Aperture)
2-8. RESERVED
2-8. RESERVED
Chap 2 Page 2-17 (and 2-18)
CHAPTER 3.THE ILS GLIDE SLOPE
3-1. GENERAL DESCRIPTION
a. Glide Slope Frequency. The ILS glide slope operates in the frequency band of 329.15 through 335.0 MHz, with 40 discrete frequencies available within this band. Each glide slope frequency is uniquely paired with a given localizer frequency, forming one ILS channel. The glide slope's guidance information is also provided by 90 HZ and 150 Hz modulation components. Identification signals are not provided with the glide slope.
3-1. GENERAL DESCRIPTION
b. Glide Slope Antenna System Location. The glide slope antenna system is located near the runway approach end at a distance from the threshold to provide optimum threshold crossing height. The preferred offset distance from the runway centerline is 400 feet. An exception is the end-fire glide slope where the antenna array typically extends to 25 feet from the runway edge and is allowed due to antenna frangibility.
c. Glide Slope Siting. The glide slope site may be located on either side of the runway. The most reliable operation will occur when it is located on the side that provides the least interference from buildings, power lines, moving vehicles, and aircraft and which has the greatest extent of smooth terrain outbound from the antennas. Category II and Category III glide slopes should be located at a minimum of 400 feet from the runway centerline.
d. Vertical Radiation Lobe Structure. Proper operation of the glide slope is primarily a function of the quality of the vertical radiation lobe structure. The system is designed so the radiation pattern has a predominance of 150 Hz signal below the glide path and conversely, a greater level of 90 Hz signal above glide path. The glide path itself is the locus of the points where equal levels of 90 and 150 Hz signals exist. The elevation angle of the glide path is a function of the antennas' heights above ground in the image systems. For the end-fire system, the relative phase of the RF radiation from the rear and front course antennas determines the glide path angle.
e. Glide Slope Receiver. The aircraft glide slope receiver responds to the difference in detected levels of the 90 Hz and 150 Hz signals. When the aircraft is on the glide path, the glide path cross-pointer receives equal levels of 90 Hz and 150 Hz signals and remains at mid-scale; the cross-pointer deflects downward when the aircraft is above path (90 Hz predominate) and upward when below path (150 Hz predominate) indicating “fly-down” and “fly-up,’ respectively. The vertical angle corresponding to full-scale deflection for the cross pointer (+150μA & -150μA on a calibrated receiver) is defined as the glide path sector width.
f. Smooth Line Approach. It is desirable that the glide path be a smooth line approaching a theoretical hyperbolic curve. In the area above and below the path sector width (the clearance signal area), the differences in the detected 90 Hz and 150 Hz signals must be sufficient to maintain the cross-pointer in a fully deflected position. The latter is of particular importance in the below-path areas. The glide slope Standard Service Volume is 10 nautical miles, with a horizontal coverage of 8 degrees on each side of the localizer course, abeam the glide slope origination point.
g. Displacement. The maximum permissible displacement of the glide path due to bends, scalloping, or roughness in Category I, II, and III operations is tabulated in Section 217 of FAA Order 8200.1.
h. Terrain Conditions. The capability of the glide slope to meet the operational requirements depends to a great extent on the terrain conditions between the antenna system and the receiving aircraft and the absence of objects that may reflect undesirable energy into the glide path region.
3-2. GLIDE SLOPE ANTENNA ARRAY SELECTION
3-2. GLIDE SLOPE ANTENNA ARRAY SELECTION
The selection of antenna array is highly dependent on the near-field and far-field terrain characteristics in front of the glide slope. Refer to Figures 3-7 and 3-8 regarding typical ground plane requirements and far-field considerations.
a. Image type glide slopes.
(1) Null Reference. The null reference is the simplest of glide slopes; however, it requires a more extensive smooth ground plane and is the most affected by rising terrain or reflectors in the far-field.
(2) Sideband Reference. The sideband reference can operate with the least amount of smooth ground plane due to lower antenna heights; however, the immediate ground plane has more stringent smoothness criteria. Sideband reference works well where terrain drops after a short ground plane and has minimal rising terrain beyond.
(3) Capture Effect. Capture effect is the most tolerant to far-field reflectors and rising terrain. It is also more complex in that it uses separate transmitters to provide the course and clearances. It is generally the system of choice for difficult sites.
b. Non-Image type glide slopes.
(1) End-fire Glide Slope. Unlike image type glide slopes, the end-fire does not use a ground plane to form the pattern. Since siting is close to the runway edge, the end-fire is ideally suited to locations where the lateral terrain is limited, or extensive site preparation would be required for an image system.
(2) RESERVED
(2) RESERVED
3-3. TERRAIN CONSIDERATIONS FOR IMAGE-TYPE GLIDE SLOPES
a. Basic Theory. The glide slope guidance signal depends on the terrain conditions due to the inherent image antenna concept: radiation from an antenna located above a reflecting surface. The reflected signal appears to emanate from an “image" antenna along the same vertical plane as the real antenna and at a distance below the reflecting surface equal to the distance of the real antenna above the surface (see Figure 3-1). The signals from the real and image antenna combine vectorially in space; therefore, the three types of glide slopes are often referred to as “image" systems. The glide path information (null reference system) is formed by
3-3. TERRAIN CONSIDERATIONS FOR IMAGE-TYPE GLIDE SLOPES
the vector sum of four different signals: the direct and reflected signals from the carrier antenna and the direct and reflected signals from the sideband antenna.
Direct Signal Reflected Signal
Glide Slope Aircraft Antennas
H
h Glide Angle
Ground Plane
Geometric Reflection Points
Image Antennas
Figure 3-1. Image Antenna Concept
b. Fresnel Zone Considerations. Although Figure 3-1 indicates a single point of reflected energy, reflection actually occurs from the entire area, which is illuminated by the signals from the antenna. The area of reflection consists of a number of concentric zones called Fresnel zones (see Appendix 3), which are numbered outward. The extent of each Fresnel zone is determined by the phase lag of the reflected signal from that zone. The phase lag is a function of the differential path length between the direct and reflected signals, with the phase from each zone lagging that from the next inner zone by pi radians or 180 degrees. Signals from the second and succeeding zones, being of approximately the same amplitude but opposite in phase, cancel almost completely; therefore, when siting the glide slope, only the first Fresnel zone normally needs to be considered.
c. Fresnel Zone Size and Position. The size and position of the glide slope Fresnel zone is a function of the glide path angle and the aircraft's elevation and distance from the facility. When an aircraft is over the outer marker, the Fresnel zone appears as a long narrow ellipse. As the aircraft approaches the runway, the ellipse becomes continuously smaller and gradually migrates as depicted in Figure 3-2. The distance to the geometric ground reflection point and the distance to the Fresnel zone center are plotted in Figures 3-3 and 3-4 respectively for various glide path angles. The length and width of the Fresnel zone are plotted in Figures 3-5
and 3-6 respectively. These graphs are for the sideband (upper) antenna, for a null reference system, and for ideal reflecting terrain.
G.S. Direction of ANTENNAS Zone Length Approach (Major Axis)
Zone Width (Minor Axis) ILS RUNWAY MM OM
Figure 3-2. First Fresnel Zones for ILS Glide Slope
d. Fresnel Zone Terrain Conditions. The quality of the glide slope information, the smoothness of the glide path, the linearity of the normal approach envelope transitions, and the adequacy of the off-path clearances, are a function of the Fresnel zone terrain conditions. Where the terrain encompassing all of the Fresnel zone is level and uniform, the glide slope signals will approach the theoretical values; where the terrain is irregular or non-uniform, the glide slope will deteriorate accordingly. It is necessary, therefore, to determine whether the terrain's departure from the perfect ground plane can still provide a satisfactory glide slope facility.
e. Fresnel Zone Terrain Considerations. Items to consider when determining the extent of departure of the glide slope terrain from a perfect ground plane include the consistency of the terrain and its coefficient of reflection, the terrain slope or departure of the terrain from the horizontal plane, and the magnitude and extent of broken or irregular terrain or terrain roughness.
(1) Glide Angle and Graze Angle Considerations. For the horizontally polarized glide slope radiation and the low grazing angle of the ground-reflected far-field signal, the ground plane coefficient of reflection has a range of 0.94 for dry, sandy soil to 1.0 for seawater. Therefore, if the Fresnel zone surface is smooth and constant, the coefficient of reflection can be assumed to equal one (R=1) without introducing significant error. Where the Fresnel zone is smooth but not consistent, as where the approach path is partially over water, a change may be encountered in the received signal as the coefficient of reflection changes abruptly. This effect is unavoidable; however, it can be minimized by establishing the lowest possible glide angle (and, therefore, the lowest possible grazing angle) and/or locating the glide slope antennas within the specified criteria, so that the change in the received signal does not occur within a critical part of the approach.
(a) Two additional problems encountered with above-water approaches are the vertical shift in the plane of the Fresnel zone resulting from tides and the dispersion of the ground plane signal by high waves or choppy water. Where these conditions are encountered, the antennas should be located to take advantage of the greatest amount of soil reflection, and possible use of a sideband reference or end-fire system may be required.
2/14/2005
14
12
10
8 H et 6
8 H et 6
4
2
θ = 2.0°
θ =2.5°
θ =3.0°
5
6750.16D
40
2 3 4 10
20
30
50 60
Aircraft distance from Glide Slope in thousands of feet
Figure 3-3. Location of Glide Slope Geometric Ground Reflection Points
Chap 3
2/14/2005
25
20
15
10
5
1
2
6750.16D
θ = 2.0°
θ =2.5°
θ=3.0°
3 4 5 10 20 30 40 50 60 Aircraft distance from Glide Slope in thousands of feet
Figure 3-4. Location of Glide Slope Fresnel Zone Centers
4
3.5
3
2.5
2
1.5
1
0.5
2
θ = 2.0°
θ = 2.50
θ=3.0°
3 5 10 20 30 40 50 60 Aircraft distance from Glide Slope in thousands of feet
Figure 3-5. First Fresnel Zone Length As Function of Glide Angle and Aircraft Distance from
Chap 3
Glide Slope
160
140 θ = 2.0°
120 A=2.50 100 0 = 3.0° 80
60
40
20
0 0 1 2 3 4 5 10 20 30 40 50 60 Aircraft distance from Glide Slope in thousands of feet
Figure 3-6. First Fresnel Zone Width as Function of Glide Angle and Aircraft Distance from Glide Slope
(2) Terrain Slope Considerations. The theoretically evolved glide slope assumes that the ground surface lies in the horizontal plane. In practice, this is seldom the case, because the terrain at and in the vicinity of most airports generally has some slope. As a result, the radiation patterns will be rotated either up or down relative to the horizontal plane through the base of the antenna mast in the same direction and by the same amount as the terrain's longitudinal slope. With the slope at a constant rate, the effect is overcome by adjustment of the glide angle in a direction opposite to and by the same amount as the slope angle.
(3) Terrain Roughness Considerations. Terrain irregularity or roughness is the worst and most common glide slope siting deficiency. The degrading effect of rough terrain results from the random dispersion and/or phase shift of the ground plane signal, which precludes formation of the desired glide slope pattern. Since it is obviously not feasible to provide a smooth ground plane for the entire glide slope Fresnel surface, it is necessary to establish a terrain roughness that can be tolerated.
(a) Criterion for Roughness. Terrain is considered to be rough if the phase shift in the ground-reflected signal caused by the change in the average path length would result in an out-of-tolerance glide slope. Considering the general case of the null reference glide slope then by application of terrain roughness criteria to the glide slope (see Appendix 3):
Z ≤(.0117) (T /H)
Where: Z = height of irregularity (in feet)
T = distance from glide slope antenna to irregularity (in feet)
H = height of sideband antenna in wavelengths.
Hence, irregular terrain roughness is a function of both the distance to the irregularity and the antenna height or glide angle. For a 3.0 degree glide angle, terrain irregularities exceeding 1.22 feet per 1000 feet from the antennas would be considered as roughness: for a 2.5 degree glide angle, the limit on terrain variations would be 1 foot per 1000 feet. This methodology is in general applicable to other type glide slopes as well.
(b) Extent of Terrain Roughness. Because the terrain reflects the ground signal in a specular manner, slight departures from the smooth terrain for small distances (about 10 feet or less) will not usually have an adverse effect on the glide slope signal. The smooth terrain terminates when it encounters extensive roughness or singular roughness of a large magnitude such as a wide ditch, a hill, or valley. The reflected signal contribution must be continuous for the terrain to be considered smooth; therefore, the smooth surface terminates at the point where roughness is encountered even though a smooth reflecting surface exists beyond the roughness. Contributions from the latter surface must be considered a second order effect.
3-4. SITE PREPARATION
3-4. SITE PREPARATION
The ideal siting environment is a perfectly smooth, level ground surface both laterally and longitudinally, and an infinite ground plane extent. Although this is desirable to provide an ideal operating environment for each glide slope facility, at most locations considerations such as drainage requires compromise. To the extent practical, grading contours should be straight, parallel, and equally spaced, within grading lateral slope limits, to provide a consistent ground plane throughout the approach. When preparing a given site, several factors must be considered:
a. Grading criteria. Unique Fresnel Zones exist for each observation point. On an approach inbound to threshold, the Fresnel Zone rotates inward and decreases in both length and width. As indicated by Figures 3-2, 3-3, 3-4, 3-5, and 3-6, the first Fresnel zone extends from the antennas outward for up to 3000 feet and up to 130 feet wide. It would be desirable to grade the entire area encompassing the Fresnel zones to provide a smooth ground plane. In accordance with the roughness criteria and economic feasibility, this should be done; however, at most locations the Fresnel zone extends beyond the airport boundaries. This limits the terrain that can be graded. A site conforming to the minimum grading criteria as depicted in Figure 3-7, will generally provide a satisfactory glide slope if the terrain beyond the specified limits does not contain severe irregularities or interference sources.
(1) Optimum Values. Several requirements are implicitly related, with each affecting the computation of the correct longitudinal distance and limiting the permissible values of the remaining items. However, by initially using the ideal or optimum values for the more critical items, the longitudinal distance, which will satisfy the optimum conditions, can be determined. Then by incrementally adjusting the values and the longitudinal distance within the assigned limits, compliance with the remaining requirements can be attained.
(2) Maximization of Smooth Terrain. Where there is a limited amount of smooth terrain in front of the ideal location, the longitudinal distance should be increased, with a corresponding adjustment in the remaining parameters, within the defined limits, to provide the greatest extent of smooth terrain. In addition, where the smooth terrain is limited, a sideband reference, capture effect, or end-fire system will generally be required (see Figure 3-8). If a sideband reference system is used, the lower antenna height requirements may permit a reduction in the lateral distance and, thereby, a possible increase in the extent of smooth terrain. Since a capture effect system requires a higher antenna mast than a null reference system, a greater distance may be required.
(3) Longitudinal Placement. The glide slope must be established between 2.0 and 4.0 degrees and is typically established with a path angle of 3.00 degrees. Obstacle consideration may dictate a higher angle. Glide slope longitudinal placement is derived from the path angle and threshold crossing height as defined by FAA Order 8260.3, TERPS. Regional Flight Procedures Office (FPO) personnel can provide the angle and threshold crossing height.
b. Severe Terrain Discontinuities. Severe terrain discontinuities, which would require extensive and infeasible landfill or cutting operations to provide the required smooth terrain, limit the use of the null-reference glide slope. Where this type of siting condition is encountered, the use of an alternate image type glide slope or end-fire glide slope must be considered during the analysis. Where the smooth terrain extends for a distance of less than 2000 feet, a sideband reference system may provide satisfactory operation; if terrain roughness is severe throughout the Fresnel zone area, a capture effect or endfire glide slope should be considered. If the costs of site preparation to install an image antenna system are excessive, comparative costs of an endfire system should be considered.
c. Signal Interference Sources. The presence of signal interference sources (such as power lines, fences, buildings, and other metallic structures), which may reflect the glide slope signal into the usable sector should be considered during the site analysis. When feasible, all such objects should be removed, particularly those in the approach zone. If removal is impossible and the interference source is sufficiently low, a capture effect system will partially overcome the effects of the low-angle reflections.
d. Glide Slope Location. The glide slope may be located on either side of the runway; therefore, all other siting factors (terrain, accessibility, etc.) being equal, the glide slope should be located on that side of the runway which is free of taxiways, runways, helicopter pads, and other potential sources of traffic interference (see Paragraph 1-15). To preclude relocations necessitated by new construction, future airport expansion plans should also be considered when determining the site selection.
e. Exclusion. If the siting conditions offer no satisfactory alternatives, exclusion of the glide slope and the establishment of a partial ILS should be considered. Every effort, however, should be made to site a glide slope because the presence of the vertical guidance provides a stabilized descent. The partial ILS consisting of a localizer and outer marker may provide sufficient improvement in the landing minimums or the safety factor to justify omission of the vertical guidance information provided by the glide slope.
Area "C"
400 A C ILS Gide 50 GS Mast 200 Slope Distances GS (Note 2) Ceterline Area "B"
200-850*
Area "A"
A 800 - 1200 *
ILS Runway (Note 1] Threshold
Direction of * . as determined by operational requirements and terran conditions. Approach
θ = Glide slope angle Section A-A a= Desired descent angle (Note 3)
Runway Pavement Edge Drop 0.8
B Ground Plane(GP) A -C
GP 125 System (Feet) Max GP Smoothness (Are a "A")
NR 1500 8/5 ±" from Avg Grade Treated Shouider Fill to line ABC 2000
SBR CEGS 1200 800 (All Values Typical) 8/4 8/3 ±0" from Avg Grade ±4" from Avg Grade Terrain slope, s, = 3 0% max. Terrain smoothness: ±0.5foot
NOTES: 1. Locate gide slope on rurway side awayfrom taxiways,rcads, etc. 2. Distances Y- The greater of 1200 feet or the setback of the glide slope from threshold 2 - The least of : [a) 3000 feet: (b) d stance to the airport property line; (c ) d stance to where smocth terraintermirates. 3. Grading and obstruction removal a. Area A should be uniformly graded and should have the same Iongitudinal sl ope as the runway. b. Area B should be smodthy gaded to comply withterrainmougmess criterion of paragraph 3-3e(3 Ia). Extensive landfill operations determined by feasibility. c. Area C grading may be limited to removal of hill s which wouldreflect the glide slope signa irto the usable area. d. All possible irterference sources (metallic structures,fenœs, etc.) should be removed from areas A, B, and that portion of C that is within 250 feet df the arterna centerline extended. (Refer to paragraph 3-4c.)
Figure 3-7. Grading Criteria for Image-Type ILS Glide Slopes
glide slope glide slope glide slope antenna antenna “up-slope” antenna area "up-slope" 0 to +1° area
5 miles 1000 - 5000' 0 to -1 1000- 5000' Type 1: Ideal Type 2: Terrain Slopes Upwards Type 3: Terrain Slopes Upwards Above Initial Terrain-Projected Below Initial Terrain-Projected
glide slope glide slope antennà "up-slope" area antenna 0 to +1°
Less than 700 Λ 1000 - 0 to -1° 5000 V Type 4: No Up-slope Area: Type 5: Combination of Types 2 and 3 Limited Terrain In Front Of Array
Type 1 Type 2 Type 3 Type 4 Type 5 Percent of Total Sites 5 20 15 15 45 Null Reference all very few few none very few Sideband Reference all few many very few few Capture Effect all most most none most End Fire all many all all many
Figure 3-8. Expected Applicability of Glide Slope Systems to Different Siting Conditions
Continue reading ↓ 120 of 235 passages shown