Radar Vectors
Advisory Circular Cancelled Issued Oct 4, 2023 AFS-400 129 pages Copy saved Nov 18, 2026

AC 91-70C Oceanic and Remote Continental Airspace Operations

The Federal Aviation Administration (FAA) (“we”) developed this AC to provide general information and guidance for certificated and General Aviation (GA) operators (“you”) planning flights in oceanic and remote continental airspace. This guidance includes the authorizations you may need for operations in such airspace. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies.

This document is cancelled. Cancelled by 91-70D. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Oceanic and Remote Continental

Airspace Operations

Date: 10/4/23 AC No: 91-70C Initiated by: AFS-400 Change:

This advisory circular (AC) contains both general information and detailed guidance for operators planning flights in oceanic and remote continental airspace. This includes Performance-based Navigation (PBN) and Special Areas of Operation (SAO). The Federal Aviation Administration (FAA) revised this AC to focus on the evolving operations in oceanic and remote continental airspace. This AC is laid out in a building block format, beginning with foundational information, followed by information on the training, authorizations, and equipment required to operate most efficiently in this airspace, and finishing with flight planning, flight execution, and contingency operations guidance. Our goal is to provide you with a template to guide you through planning and executing flight operations through oceanic and remote continental airspace.

Information related to international operations in specific locales continues to be available in the North Atlantic (NAT) Resource Guide for United States Operators; the West Atlantic, Gulf of Mexico, and Caribbean Resource Guide for U.S. Operators; and the Pacific Resource Guide for U.S. Operators. These online resource guides, along with Notices to Air Missions (NOTAM) and FAA International Notices, provide the most current information available to pilots, aircraft dispatchers, and other operational control personnel preparing for oceanic and international operations. We have also included hyperlinks to many documents, available free or for purchase. While we carefully checked at the time of publication that information included in this AC is current, oceanic and remote continental airspace operations are constantly evolving, and it is incumbent on you, the operators, to ensure you are flying with current information.

This AC neither is mandatory nor does it constitute a regulation. When this AC uses mandatory language (e.g., “must” or “may not”), it is quoting or paraphrasing a regulatory requirement or prohibition. When this AC uses permissive language (e.g., “should” or “may”), it describes an acceptable means, but not the only means, of conducting that aspect of operations in oceanic and remote continental airspace. However, if you use the means described in the AC, you must follow them in all important respects.

Wesley L. Mooty Acting Deputy Executive Director, Flight Standards Service

ii

CONTENTS Paragraph Page

Chapter 1. General … 1-1

1.1 Purpose of This Advisory Circular (AC) … 1-1

1.2 Audience … 1-1

1.3 Where You Can Find This AC … 1-1

1.4 What This AC Cancels … 1-1

1.5 Fundamental Changes From Previous Edition … 1-1

1.6 Related Title 14 Of The Code Of Federal Regulations (14 CFR) Parts … 1-1

1.7 Related Reading Material (Current Editions) … 1-2

1.8 AC Feedback Form … 1-3

Chapter 2. Background Information for Operations in Oceanic and Remote

Continental Airspace … 2-1

2.1 ICAO: Its Relationship to U.S. Aviation … 2-1

2.2 ICAO Annexes … 2-1

2.3 Applicability of U.S. and International Regulations … 2-3

2.4 ICAO Guidance Documents and Reference Material … 2-5

2.5 Authorization to Operate in Oceanic/Remote Continental Airspace and Special Areas of Operation (SAO) … 2-9

2.6 Authorization Process … 2-9

2.7 Web-Based Operations Safety System (WebOPSS) … 2-10

Chapter 3. Pilot Qualification and Training Guidance for Oceanic and Remote Continental

Airspace Operations … 3-1

3.1 Training Requirements for Oceanic and Remote Continental Airspace Operations … 3-1

Chapter 4. Communications, Navigation, and Surveillance Systems Guidance for

Operations in Oceanic and Remote Continental Airspace … 4-1

4.1 Communications, Navigation, and Surveillance Improvements—Impact on ATS … 4-1

4.2 Performance-Based Operations … 4-1

4.3 Voice Communications in Oceanic Airspace … 4-3

4.4 CPDLC and Automatic Dependent Surveillance-Contract (ADS-C) … 4-7

4.5 Data Link Systems—Operational Authorization to Use … 4-9

iii

4.6 ATC in Oceanic and Remote Continental Airspace … 4-10

4.7 Special Use Airspace (SUA) … 4-12

4.8 Air Defense Identification Zones (ADIZ) … 4-13

4.9 World Geodetic System 1984 (WGS 84) … 4-13

Chapter 5. Flight Planning Guidance for International and Oceanic and Remote

Continental Airspace Operations … 5-1

5.1 Lead Time Requirements … 5-1

5.2 Preparing an Itinerary … 5-1

5.3 Crew Fatigue … 5-4

5.4 Required Paperwork/Documentation … 5-4

5.5 Entry to Foreign Airspace—Flight Plan vs. Formal Advance Permission … 5-7

5.6 Managing Risk in Oceanic and Remote Continental Airspace Operations … 5-7

5.7 Weather Forecasts and Other Meteorological Planning … 5-7

5.8 FAA International Notices Website … 5-8

5.9 ETOPS … 5-8

5.10 Polar Operations … 5-9

5.11 Areas With Limited or No ATS (Also Called “No FIR” Areas) … 5-9

5.12 Rotorcraft Operations … 5-10

Chapter 6. Flight Execution Guidance for Operations in Oceanic and Remote

Continental Airspace … 6-1

6.1 General Information … 6-1

6.2 Flight Plan … 6-5

6.3 Aircraft Preflight Guidance … 6-6

6.4 En Route Guidance … 6-12

Chapter 7. In-Flight Contingency Guidance for Operations in Oceanic Airspace … 7-1

7.1 Contingency Procedures: When They May Be Needed … 7-1

7.2 Choosing The Correct Contingency Procedure … 7-1

7.3 Altimetry and/or Navigation Degradation … 7-2

7.4 Lost Communications Procedures … 7-2

7.5 Normal Aircraft Tracking … 7-3

iv

Appendix A. Abbreviations and Definitions … A-1

Appendix B. Special Areas of Operation and OpSpecs/MSpecs/LOAs … B-1

Appendix C. Unusual Weather Activity … C-1

Appendix D. Sample Oceanic Checklist … D-1

Appendix E. IATA In-Flight Broadcast Procedure … E-1

Appendix F. Special Procedures for In-Flight Contingencies in Oceanic Airspace … F-1

Appendix G. Suggested Subjects for Inclusion in Oceanic and International Procedures

and/or an Operations Manual … G-1

List of Figures

Figure 4-1. Sample CPDLC Route Uplinks … 4-9

Figure 6-1. Sample Plotting Chart … 6-8

Figure C-1. ICAO Volcanic Ash Advisory Centers … C-1

Figure C-2. Example of a National Oceanic and Atmospheric Administration Scales

Activity Report … C-3

Figure E-1. Map of IFBP Area of Applicability … E-2

Figure F-1. Special Procedures for In-Flight Contingencies in Oceanic Airspace

(Non-Weather) … F-1

Figure F-2. Special Procedures for In-Flight Weather Contingencies … F-6

List of Tables

Table 6-1. Examples of Incorrectly Applied Conditional Clearances … 6-2

Table B-1. SAO-Related OpSpecs/MSpecs/LOAs … B-1

Table B-2. Oceanic and Remote/General En Route OpSpecs/MSpecs/LOAs … B-2

Table F-1. Altitude Offset When Denied Clearance to Deviate 9.3 km (5.0 NM) or More (5 NM Procedures) … F-7

CHAPTER 1. GENERAL › 1.6 Related Title 14 of the Code of Federal Regulations (14 CFR) Parts.

CHAPTER 1. GENERAL

1.1 Purpose of This Advisory Circular (AC). The Federal Aviation Administration (FAA) (“we”) developed this AC to provide general information and guidance for certificated and General Aviation (GA) operators (“you”) planning flights in oceanic and remote continental airspace. This guidance includes the authorizations you may need for operations in such airspace. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies.

1.2 Audience. We wrote this AC primarily for operators who do not have experience with flying in oceanic and remote continental airspace, to assist in developing their own procedures. We also wrote this AC for GA pilots who do not fly regularly in oceanic and remote continental airspace and need a refresher in planning and executing such a flight. Most certificated operators have company procedures for operations in oceanic and remote continental airspace. Those procedures have been accepted by FAA inspectors and conform to all relevant regulations and guidance. If you are working for one of these operators, this AC may serve to reinforce your company procedures.

1.3 Where You Can Find This AC. You can find this AC on the FAA’s website at https://www.faa.gov/regulations_policies/advisory_circulars.

1.4 What This AC Cancels. AC 91-70B CHG 1, Oceanic and Remote Continental Operations, dated February 1, 2019, is canceled.

1.5 Fundamental Changes From Previous Edition. This revision of AC 91-70 contains numerous changes from the previous edition, many of which clarify or amplify information provided earlier. Operators should review this revised AC in its entirety. We have added information on the use of Satellite Voice (SATVOICE) communications, Controller-Pilot Data Link Communication (CPDLC), and space-based Automatic Dependent Surveillance-Broadcast (ADS-B), as well as updated information on common causes of pilot deviations and re-emphasized the importance of accurate flight plan equipment and capability codes. We updated the contingency procedures, in line with International Civil Aviation Organization (ICAO) changes, and explain the requirements for oceanic authorizations. Finally, we provide updated links to the most current sources of international material.

1.6 Related Title 14 of the Code of Federal Regulations (14 CFR) Parts.

• Part 91, §§ 91.1 through 91.21, 91.101 through 91.143, 91.151 through 91.159, 91.167 through 91.193, 91.203, 91.205, 91.209 through 91.217, 91.221, 91.225, 91.227, 91.303 through 91.319, 91.323, 91.509, 91.511, 91.605, 91.609, 91.703 through 91.715, 91.903, 91.1039, and 91.1073; and Appendix G.

• Part 119, §§ 119.5, 119.49, 119.59, and 119.63.

1.7 Related Reading Material (current editions). › 1.7.3 FAA ACs.

• Part 121, §§ 121.11, 121.101, 121.121, 121.163, 121.339, 121.351, 121.353, 121.355, 121.401, 121.415, 121.427, and 121.445; and Appendix G.

• Part 125, §§ 125.23, 125.45, 125.51, 125.203, 125.209, 125.296, and 125.363.

• Part 135, §§ 135.3, 135.43, 135.145, 135.165, 135.167, 135.183, 135.213, 135.323, 135.329, 135.351, 135.364, and 135.381; and Appendix G.

1.7 Related Reading Material (current editions).

1.7.1 RTCA Documents. Available for purchase on the RTCA website at https://www.rtca.org/standards.

1. RTCA/DO-258/ED-100, Interoperability Requirements for ATS Applications Using ARINC 622 Data Communications.

2. RTCA/DO-260/ED-102, Minimum Operational Performance Standards (MOPS) for 1090 MHz Extended Squitter Automatic Dependent Surveillance-Broadcast (ADS-B) and Traffic Information Services – Broadcast (TIS-B).

3. RTCA/DO-306/ED-122, Safety and Performance Standard for Air Traffic Data Link Services in Oceanic and Remote Airspace (Oceanic SPR Standard).

4. RTCA/DO-350/ED-228, Safety and Performance Requirements Standard for Baseline 2 ATS Data Communications (Baseline 2 SPR Standard).

1.7.2 FAA Technical Standard Orders (TSO).

1. TSO-C115, Flight Management System (FMS) Using Multi-Sensor Inputs.

2. TSO-C145, Airborne Navigation Sensors Using The Global Positioning System Augmented by the Satellite Based Augmentation System (SBAS).

3. TSO-C146, Stand-Alone Airborne Navigation Equipment Using The Global Positioning System Augmented by the Satellite Based Augmentation System (SBAS).

4. TSO-C196, Airborne Supplemental Navigation Sensors for Global Positioning System Equipment Using Aircraft-Based Augmentation.

1.7.3 FAA ACs.

1. AC 20-138, Airworthiness Approval of Positioning and Navigation Systems.

2. AC 20-140, Guidelines for Design Approval of Aircraft Data Link Communication Systems Supporting Air Traffic Services (ATS).

3. AC 20-150, Airworthiness Approval of Satellite Voice (SATVOICE) Equipment Supporting Air Traffic Service (ATS) Communication.

4. AC 90-80, Approval of Offshore Standard Approach Procedures, Airborne Radar Approaches, and Helicopter En Route Descent Areas.

5. AC 90-96, Approval of U.S. Operators and Aircraft to Operate Under Instrument Flight Rules (IFR) in European Airspace Designated for Basic Area Navigation (B-RNAV) and Precision Area Navigation (P-RNAV).

CHAPTER 1. GENERAL › 1.8 AC Feedback Form.

6. AC 90-105, Approval Guidance for RNP Operations and Barometric Vertical Navigation in the U.S. National Airspace System and in Oceanic and Remote Continental Airspace.

7. AC 90-114, Automatic Dependent Surveillance-Broadcast Operations.

8. AC 90-117, Data Link Communications.

9. AC 91-85, Authorization of Aircraft and Operators for Flight in Reduced Vertical Separation Minimum (RVSM) Airspace.

10. AC 91-92, Pilot’s Guide to a Preflight Briefing.

11. AC 120-42, Extended Operations (ETOPS and Polar Operations).

12. AC 120-100, Basics of Aviation Fatigue.

13. AC 120-103, Fatigue Risk Management Systems for Aviation Safety.

14. AC 121-31, Flight Crew Sleeping Quarters and Rest Facilities.

15. AC 135-42, Extended Operations (ETOPS) and Operations in the North Polar Area.

1.7.4 FAA IFR Enroute Aeronautical Planning Charts. These charts are available at https://www.faa.gov/air_traffic/flight_info/aeronav/digital_products/ifr.

1. North Atlantic Route Chart.

2. North Pacific Route Chart.

3. Western Atlantic Route System Chart.

1.8 AC Feedback Form. For your convenience, the AC Feedback Form is the last page of this AC. Note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this AC on the AC Feedback Form.

CHAPTER 2. BACKGROUND INFORMATION FOR OPERATIONS IN OCEANIC

2.2 ICAO Annexes. › 2.2.6 Annex 6, Operation of Aircraft (3 Parts).

AND REMOTE CONTINENTAL AIRSPACE

2.1 ICAO and Its Relationship to U.S. Aviation. The United States is a Contracting State to the Convention on International Aviation (Chicago Convention) and an ICAO Member State and has fully supported the organization’s goals from its inception. ICAO works to achieve the highest level of standards and procedures for aircraft, personnel, airways, and aviation services throughout the world. ICAO oversees the international standards ascribed to by its more than 190 Member States for navigation facilities, airports, weather, and radio services. Through active support and participation in ICAO, the FAA strives to improve worldwide safety standards and procedures. ICAO’s strategic objectives are to continue to establish and maintain Standards and Recommended Practices (SARPs) for the safe and orderly development of international aviation. The 19 Annexes to the Chicago Convention (ICAO Annexes) contain more than 10,000 adopted SARPs.

Note: ICAO Member States are obligated to “collaborate in securing the highest practicable degree of uniformity in regulations” and generally achieve this by complying with the SARPs contained in the 19 Annexes and supporting ICAO documents such as ICAO Doc 4444, Procedures for Air Navigation Services—Air Traffic Management, and ICAO Doc 7030, Regional Supplementary Procedures. States notify ICAO of their “differences” with SARPs and publish them in their Aeronautical Information Publication (AIP).

2.2 ICAO Annexes. Find all ICAO Annexes at the ICAO store at https://store.icao.int.

2.2.1 Annex 1, Personnel Licensing. Provides information on licensing of flightcrews, air traffic controllers, and aircraft maintenance personnel, including medical standards for flightcrews and air traffic controllers.

2.2.2 Annex 2, Rules of the Air. Contains visual flight rules (VFR) and instrument flight rules (IFR) for all operators.

2.2.3 Annex 3, Meteorological Service for International Air Navigation. Provides for meteorological services for international air navigation and reporting of meteorological observations from aircraft.

2.2.4 Annex 4, Aeronautical Charts. Contains specifications for aeronautical charts used in international aviation.

2.2.5 Annex 5, Units of Measurement to be Used in Air and Ground Operations. Lists dimensional systems used in air and ground operations.

2.2.6 Annex 6, Operation of Aircraft (3 Parts). Specifies minimum standards for below-listed operations throughout the world:

2.2 ICAO Annexes. › 2.2.15 Annex 15, Aeronautical Information Services.

1. Part I, International Commercial Air Transport—Aeroplanes.

2. Part II, International General Aviation—Aeroplanes.

3. Part III, International Operations—Helicopters.

2.2.7 Annex 7, Aircraft Nationality and Registration Marks. Specifies requirements for registration and identification of aircraft.

2.2.8 Annex 8, Airworthiness of Aircraft. Specifies uniform procedures for certification and inspection of aircraft.

2.2.9 Annex 9, Facilitation. Provides for the standardization and simplification of border-crossing formalities.

2.2.10 Annex 10, Aeronautical Telecommunications:

1. Volume I, Radio Navigation Aids. Provides for standardizing communications equipment and systems.

2. Volume II, Communication Procedures including those with PANS status. Standardizes communications procedures.

3. Volume III, Communication Systems. Standardizes communications systems.

4. Volume IV, Surveillance and Collision Avoidance Systems. Standardizes surveillance radar and collision avoidance.

5. Volume V, Aeronautical Radio Frequency Spectrum Utilization. Standardizes aeronautical radio spectrum utilization.

2.2.11 Annex 11, Air Traffic Services. Includes information on establishing and operating air traffic control (ATC), flight information, and alerting services.

2.2.12 Annex 12, Search and Rescue. Provides information on organization and operation of facilities and services necessary for Search and Rescue (SAR).

2.2.13 Annex 13, Aircraft Accident and Incident Investigation. Provides for uniformity in notifying, investigating, and reporting on aircraft accidents.

2.2.14 Annex 14, Aerodromes:

1. Volume I, Aerodrome Design and Operations. Contains specifications for the design and equipment of aerodromes.

2. Volume II, Heliports. Contains specifications for the design and equipment of heliports.

2.2.15 Annex 15, Aeronautical Information Services. Includes methods for collecting and disseminating aeronautical information required for flight operations.

2.3.1 FAA regulations relating to certification, airworthiness,… › 2.3.1.2 Title 14 CFR part 121, § 121.351; part 125, § 125.203; and part…

2.2.16 Annex 16, Environmental Protection:

1. Volume I, Aircraft Noise. Contains specifications for aircraft noise certification, noise monitoring, and noise exposure units for land-use planning.

2. Volume II, Aircraft Engine Emissions. Contains specifications for aircraft engine emissions.

3. Volume III, Aeroplane CO2 Emissions.

4. Volume IV, Carbon Offsetting and Reduction Scheme for International Aviation (CORSIA).

2.2.17 Annex 17, Security. Specifies methods for safeguarding international civil aviation against unlawful acts of interference.

2.2.18 Annex 18, The Safe Transport of Dangerous Goods by Air. Contains specifications for labeling, packing, and shipping dangerous cargo.

2.2.19 Annex 19, Safety Management. Describes Safety Management System (SMS) development, regulatory framework, and supporting guidance.

2.3 Applicability of U.S. and International Regulations.

2.3.1 FAA regulations relating to certification, airworthiness, licensing, and certain operational aspects (e.g., operational control, communication and navigation equipment, and Extended Operations (ETOPS)), are applicable to U.S. operators wherever they fly. Some of these regulations are fundamental to oceanic operations:

2.3.1.1 Title 14 CFR part 91, § 91.511 (applicable to part 91 subpart F), deals with “overwater” operations which are more than 30 minutes or 100 nautical miles (NM) from the nearest shore.

Note: Section 91.511(b) notes that a unit is “independent if the function of any part of it does not depend on the functioning of any part of another receiver or electronic navigation unit.”

2.3.1.1.1 For such operations, two independent long-range navigation systems (LRNS) are required, except in an area defined by coordinates in § 91.511(f), where only one LRNS is sufficient.

2.3.1.1.2 Part 91 subpart F overwater operations outside very high frequency (VHF) voice communication coverage require two long-range communication systems (LRCS), except when an aircraft has two VHF radios, in which case only one high frequency (HF) radio is sufficient.

2.3.1.2 Title 14 CFR part 121, § 121.351; part 125, § 125.203; and part 135, § 135.165 use a different term, “extended over-water” operations, defined in 14 CFR part 1, § 1.1 as more than 50 NM from the nearest shoreline.

2.3.3 U.S. operators flying outside U.S. sovereign airspace must abide… › 2.3.3.2 According to §§ 121.11, 125.23(b), and 135.3(a)(2), for…

2.3.1.2.1 Section 121.351 specifically requires two “independent long-range navigation systems” for extended over-water operations.

2.3.1.2.2 Sections 125.203 and 135.165 use different language, and only require “two approved independent navigation systems suitable for navigating the airplane along the route” within the “degree of accuracy required for ATC.” This allows extended over-water operations along ATS routes that have ground-based Navigational Aid (NAVAID) coverage, without any LRNS.

2.3.1.2.3 For parts 121, 125, and 135, extended over-water operations “in certain geographic areas” with only a single LRNS can be authorized via operations specification (OpSpec) B054, which defines an area by coordinates where only one LRNS is sufficient.

2.3.1.2.4 Extended overwater operations outside VHF voice communication coverage require two LRCSs, except for holders of OpSpec B045, which defines an area by coordinates where only one LRCS is sufficient.

2.3.2 FAA regulations governing “Flight Rules” (this is the title of part 91 subpart B), on the other hand, are applicable to all operators, in U.S. sovereign airspace only.1 These so-called “flight and maneuver” regulations are generally harmonized with ICAO rules, in accordance with Article 12 to the Chicago Convention. Exceptions are listed as “Differences” in the relevant AIP. In the U.S. AIP, these are found in Section GEN 1.7, Differences From ICAO Standards, Recommended Practices and Procedures.

2.3.3 U.S. operators flying outside U.S. sovereign airspace must abide by the “flight and maneuver” regulations in effect for that airspace. If the airspace is “high seas” (“high seas” airspace generally begins outside 12 NM from the nearest shore), the applicable rules are found in ICAO Annex 2 (titled “Rules of the Air”), and ICAO Doc 7030.2 In other countries’ sovereign airspace, information on regulations is found in the relevant AIP, with Differences from ICAO SARPs also notified there.

2.3.3.1 Section 91.703 says that you must comply with ICAO Annex 2 if you operate your U.S.-registered aircraft “over the high seas.” Section 91.703 further requires that you, when within a foreign country, follow the rules “relating to the flight and maneuver of aircraft there in force.”

2.3.3.2 According to §§ 121.11, 125.23(b), and 135.3(a)(2), for operations under each respective part, when operating within a foreign country, you must comply with the air traffic rules of the country concerned and any local airport rules that may be in force. You must also follow all rules of that part that are more

1 Exception: § 91.703 imposes the following subpart B flight rules for operations of civil aircraft of U.S. registry over the high seas: §§ 91.117(c), 91.127, 91.129, and 91.131. 2 In addition, 14 CFR contains three flight and maneuver regulations (listed in footnote 1) which apply to operations of civil aircraft of U.S. registry over the high seas.

2.4.3.2 Procedures for Air Navigation Services (PANS) and Regional… › 2.4.3.2.1 ICAO Doc 4444, Procedures for Air Navigation Services—Air…

restrictive than the rules of the foreign country in which you are operating, as long as you can do so without violating the rules of that country.

Note: In some countries, Annex 6 fuel requirements are in force, which may be more restrictive than applicable 14 CFR rules.

2.3.4 Differing Airspace Requirements. It is quite possible to transit regions with significantly different procedures in one long-range flight. Therefore, you should familiarize yourself with the equipment and procedural requirements to file and fly in each segment of foreign airspace in which you intend to operate by referencing, for example, the appropriate State’s AIP.

2.4 ICAO Guidance Documents and Reference Material. Find the following ICAO documents at the ICAO store at https://store.icao.int.

2.4.1 Guidance Documents. We developed much of the material in this AC from these foundational documents: ICAO Annexes, other ICAO guidance documents, related sections of 14 CFR, and other FAA guidance material.

2.4.2 Chicago Convention. We single out the following articles of the Convention on International Civil Aviation (listed in ICAO Doc 7300) because of their importance in regulating international aviation. If you operate in oceanic and remote continental airspace, you should thoroughly understand them.

• Article 1, Sovereignty.

• Article 12, Rules of the Air.

• Article 29, Documents Carried in Aircraft.

2.4.3 ICAO Publications. The principal purpose of ICAO publications is the “systematic and prompt dissemination in concise form of the policies and activities of the Organization…” These publications consist of Annexes, documents with “Procedures for Air Navigation Services” and “Regional Supplementary Procedures” in the name, manuals, and other similar publications. The following is a brief description of each category of publications, beginning with the most authoritative, and moving down the hierarchy.

2.4.3.1 Annexes. There are 19 Annexes (named in paragraph 2.2 above) to the Convention on International Civil Aviation (listed in ICAO Doc 7300). They state the SARPs.

2.4.3.2 Procedures for Air Navigation Services (PANS) and Regional Supplementary Procedures (SUPPS). ICAO publications with “Procedures for Air Navigation Services” in the title have special status, as does the publication “Regional Supplementary Procedures.”

2.4.3.2.1 ICAO Doc 4444, Procedures for Air Navigation Services—Air Traffic Management (PANS-ATM). These procedures complement the SARPs

2.4.3 ICAO Publications. › 2.4.3.3 Manuals.

contained in ICAO Annex 2 and Annex 11, and specify, in greater detail than in the SARPs, the actual procedures Air Traffic Service (ATS) units apply when providing various services to air traffic.

2.4.3.2.2 ICAO Doc 8168, Procedures for Air Navigation Services—Aircraft Operations (PANS-OPS). This document has three volumes:

1. Volume I, Flight Procedures, describes operational requirements for flying the procedures designed in accordance with the criteria provided in Volume II.

2. Volume II, Construction of Visual and Instrumental Flight Procedures, is intended for the guidance of procedures specialists and describes the essential areas and obstacle clearance requirements for the achievement of safe, regular instrument flight operations. It provides the basic guidelines to States, and those operators and organizations producing instrument flight charts, that will result in uniform practices at all aerodromes where instrument flight procedures are carried out.

3. Volume III, Aircraft Operating Procedures, describes operational procedures recommended for the guidance of flight operations personnel and flightcrew.

2.4.3.2.3 ICAO Doc 7030, Regional Supplementary Procedures. For each ICAO region, ICAO Doc 7030 provides detailed procedures designed to meet those needs of specific areas that are not covered in the worldwide provisions contained in the Annexes and PANS documents. The SUPPS complement the statement of requirements for facilities and services contained in the Air Navigation Plan publications.

Note: To illustrate the hierarchy among ICAO publications, we can look at the topic of communication failure. ICAO Annex 2 details global procedures on communication failure. ICAO Doc 4444 elaborates on those procedures, which, “unless otherwise prescribed on the basis of regional air navigation agreement,” are in effect. ICAO Doc 7030 describes such regional agreements. FAA principal inspectors (PI) and specialists within the FAA’s Flight Technologies and Procedures Division, Flight Operations Group can help you understand the relationship between various ICAO publications.

2.4.3.3 Manuals. Similar to our ACs, ICAO manuals provide guidance and information concerning selected aspects of aeronautical activity or facilitating the uniform application of ICAO SARPs. Therefore, you should familiarize yourself with the following documents (current editions) prior to undertaking operations in oceanic and remote continental airspace. The following are the more prominent ICAO manuals:

2.4.3.3 Manuals. › 2.4.3.3.5 ICAO NAT Doc 007, North Atlantic Operations and Airspace Manual.

2.4.3.3.1 ICAO Doc 9574, Manual on a 300m (1,000 ft) Vertical Separation Minimum Between FL 290 and FL 410 Inclusive. ICAO Doc 9574 provides States’ regional planning groups with a basis for the revision of documents, procedures, and programs to enable the maintenance of a 300m (1,000 ft) vertical separation minimum between flight level (FL) 290 and FL 410 inclusive, in accordance with the criteria and requirements developed by ICAO. It provides guidance to State aviation authorities on those measures necessary to ensure that the criteria and requirements are met within their area of responsibility, as well as background information for operators to assist in the development of operating manuals and flightcrew procedures.

2.4.3.3.2 ICAO Doc 9613, Performance-based Navigation (PBN) Manual. This manual provides practical guidance on how to implement Area Navigation (RNAV) and Required Navigation Performance (RNP) applications, and how to ensure that the performance requirements are appropriate for the planned application.

2.4.3.3.3 ICAO Doc 9869, Performance-based Communication and Surveillance (PBCS) Manual. This guidance material explains the concepts of Required Communication Performance (RCP) and Required Surveillance Performance (RSP), identifies RCP and RSP requirements applicable to the provision and use of ATS, and provides a basis for the application of RCP and RSP in a specified airspace.

2.4.3.3.4 ICAO Doc 10037, Global Operational Data Link (GOLD) Manual. The GOLD Manual addresses data link service provision, operator readiness, controller and flightcrew procedures, performance-based specifications, and post-implementation monitoring and analysis. GOLD provides guidance and information concerning data link operations and is intended to facilitate the uniform application of ICAO SARPs contained in ICAO Annex 2, Annex 10, and Annex 11; the provisions in ICAO Doc 4444; and, when necessary, ICAO Doc 7030.

2.4.3.3.5 ICAO NAT Doc 007, North Atlantic Operations and Airspace Manual. This document provides information for aircraft operating agencies, pilots, and dispatchers planning and conducting operations in or above the North Atlantic High Level Airspace (NAT HLA). It also offers guidance to the State regulators responsible for the approval/certification/licensing of such aircraft operators, pilots, or dispatchers.

Note: Operators flying below NAT HLA should pay particular attention to ICAO NAT Doc 007, Chapter 17, Flight Operations Below the NAT HLA. Information in the North Atlantic International General Aviation Operations Manual (NAT IGA) was incorporated into ICAO NAT Doc 007 in 2013.

2.4 ICAO Guidance Documents and Reference Material. › 2.4.4 Other References:

2.4.4 Other References:

1. ICAO Satellite Voice Guidance Material (SVGM), available at https://www.icao.int/apac/documents/edocs/cns/satvoice_svgm_v1.pdf. This document is intended to maximize the operational benefits of SATVOICE implementations by promoting seamless and interoperable SATVOICE operations throughout the world. The document provides guidance and information concerning SATVOICE communications for aeronautical use and is intended to facilitate the uniform application of ICAO SARPs contained in ICAO Annex 2, the provisions in ICAO Doc 4444, and, when necessary, ICAO Doc 7030.

2. The FAA website at https://www.faa.gov.

3. Resource Guides for United States Operators:

a. North Atlantic (NAT) Resource Guide for U.S. Operators at

https://www.faa.gov/headquartersoffices/avs/nat-resource-guide.

b. Pacific Resource Guide for U.S. Operators at https://www.faa.gov/headquartersof

fices/avs/pacific-resource-guide.

c. West Atlantic, Gulf of Mexico, and Caribbean Resource Guide for U.S. Operators

at https://www.faa.gov/headquartersoffices/avs/wat-gomex-and-caribbeanresource-guide.

Note: Contact information for specialists from the Flight Operations Group can be obtained from the responsible Flight Standards office, and is available in these resource guides.

4. Applicable FAA Domestic/International Notices and Notices to Air Missions (NOTAM).

5. U.S. AIP and applicable foreign AIPs. The AIP is the State’s official publication that defines and describes the airspace, aeronautical facilities, services, and national rules and practices pertaining to air traffic, particularly if they differ from ICAO SARPs (“differences” are listed in AIPs). Eurocontrol maintains a global listing of links to AIPs here: https://eurocontrol.int/articles/ais-online. Refer to the current AIP for any States whose airspace you intend to operate in/through.

6. Regulations of the foreign countries over which you intend to fly.

7. The customs procedures, cultural considerations, entry and overflight procedures, and health and safety precautions for each country in which you intend to land.

8. The “Oceanic and Remote” section of the FAA’s Flight Operations Group web page at https://www.faa.gov/about/office_org/headquarters_offices/avs/offices/afx/afs/afs4 00/afs410/oceanic_remote. See in particular the “Oceanic and Remote Continental Application Guide” posted there.

9. The “Data Communications” section of the FAA’s Flight Operations Group web page, at https://www.faa.gov/about/office_org/headquarters_offices/avs/offices/a fx/afs/afs400/afs410/datacomm/. See in particular the “Data Link Communication Application Guide” posted there.

2.6 Authorization Process. › 2.6.4 Phase 4.

10. NAT bulletins, found in the “EUR and NAT Documents” area of the ICAO website: https://www.icao.int/EURNAT/Pages/EUR-and-NAT-Document.aspx.

2.5 Authorization to Operate in Oceanic/Remote Continental Airspace and Special Areas of Operation (SAO). The FAA requires all certificated U.S. operators to obtain operational authorization to fly in oceanic and/or remote continental airspace.3 The FAA requires all operators to obtain operational authorization to fly in some or all SAOs. SAOs are areas with unique characteristics that require special equipment, procedures, and/or techniques. The Administrator grants authorization in the form of an OpSpec, a management specification (MSpec), or a Letter of Authorization (LOA), depending on what part of 14 CFR governs your operations.

2.5.1 Appendix B, Special Areas of Operation and OpSpecs/MSpecs/LOAs, provides more information on SAOs, related authorizations, and other operational authorizations pertaining to oceanic, remote continental, and en route operations.

2.5.1.1 Table B-1, SAO-Related OpSpecs/MSpecs/LOAs, lists SAOs that require authorizations, broken down by part.

2.5.1.2 Table B-2, Oceanic and Remote/General En Route OpSpecs/MSpecs/LOAs, lists operations that require authorizations, broken down by part.

2.5.2 Part 91 operators only require authorizations as indicated in the footnotes to Tables B-1 and B-2.

2.6 Authorization Process. The FAA uses a five-phase process to approve operator applications. The responsible Flight Standards office can provide you with the details pertinent to each phase and your specific requirements.

2.6.1 Phase 1. You determine a need for authorization and contact the FAA.

2.6.2 Phase 2. You formally submit a proposal for FAA evaluation.

2.6.3 Phase 3. We evaluate the request and determine what level of demonstration is required. We may conduct the demonstration within the responsible Flight Standards office, at your site of operations, or at another suitable location.

2.6.4 Phase 4. We observe and evaluate a demonstration of your ability to perform in accordance with your proposal. This is an operational evaluation. If the demonstration is unsuccessful, we will provide feedback on deficient areas and their resolution.

3 Certificated operators holding OpSpec B032/MSpec B031, En Route Limitations and Provisions, do not need OpSpec/MSpec B036, Oceanic and Remote Continental Navigation Using Multiple Long-Range Navigation Systems, provided they adhere to the OpSpec B032/MSpec B031 limitation of being able to obtain a “reliable fix” at least once each hour from a standard ICAO ground-based Navigational Aid (NAVAID).

2.7 Web-Based Operations Safety System (WebOPSS). › 2.7.2 WebOPSS Training.

Note: Flight or line observations are not required for GA LOA applications. For GA operators, we evaluate your application and if warranted, conduct a knowledge validation (tabletop exercise and/or static airplane demonstration).

2.6.5 Phase 5. If your demonstration is successful, we issue the requested OpSpec/MSpec/LOA.

2.7 Web-Based Operations Safety System (WebOPSS).

2.7.1 WebOPSS Access. WebOPSS is the FAA’s document management system for issuing OpSpecs, MSpecs, and LOAs to air operators as indicated in 14 CFR. Authorized aviation industry personnel can apply for access to WebOPSS through their PIs. WebOPSS access allows industry personnel to view and propose changes to their authorizations, which can expedite applications.

2.7.2 WebOPSS Training. You will require training prior to receiving WebOPSS access. You can accomplish the training either through an FAA inspector or by taking the WebOPSS formal training course through the FAA’s Mike Monroney Aeronautical Center (MMAC).

Note: The Operations Approval Portal System (OAPS) was introduced late 2018 to streamline processing of NextGen authorizations. OAPS allows bundling, and is integrated with WebOPSS. To register for an account, follow instructions on the web page: https://oaps.faa.gov/. For support and/or questions, email [email protected].

3.1 Training Requirements for Oceanic and Remote Continental Airspace… › 3.1.3 Relevant Subject Matter.

CHAPTER 3. PILOT QUALIFICATION AND TRAINING GUIDANCE FOR OCEANIC

AND REMOTE CONTINENTAL AIRSPACE OPERATIONS

3.1 Training Requirements for Oceanic and Remote Continental Airspace Operations.

3.1.1 Certificated Operator Training. Certificated operators are required to have training approved by the Administrator.4 This normally takes place during the certification process and prior to issuance of OpSpecs or MSpecs.

3.1.2 GA Training. If you are a GA pilot desiring to indicate RNP capability in oceanic and remote continental airspace, you need operational approval via an LOA (see Appendix B, paragraph B.1).5 One or more of the following actions may satisfy training requirements:

1. Completing an operator’s oceanic operations current training program.

2. Completing a commercial oceanic operations current training program.

3. Submitting military training records indicating prior oceanic operations experience.

4. Using other methods indicating that you can safely conduct oceanic operations. Examples could include written testing, oral testing, or evidence of prior recent experience.

3.1.3 Relevant Subject Matter. The following items are examples of the subject matter with which you should be familiar in order to conduct operations in oceanic and remote continental airspace (as required based on the types of operations being conducted):

1. Title 14 CFR (applicable parts).

2. ICAO SARPs and measurement standards.

3. Operator’s international operating procedures, to include the international operations manual,6 its organization and structure, and access via Electronic Flight Bag (EFB), as applicable.

4. Use of oceanic flight planning charts.

5. Sources and content of international flight publications.

6. Itinerary planning and overflight clearances.

7. Meteorology, including Significant Weather (SIGWX) charts, prognostic weather charts, tropopause prognostic charts, and Terminal Aerodrome Forecasts (TAF), as well as contingency procedures for weather diversions.

8. Preparation of international flight plans, plotting charts, and operational flight plans (OFP)/flight logs, to include Equal Time Point (ETP) calculations. These include the

4 Regulatory references are §§ 91.1073, 121.401, 125.296, and 135.323. 5 Regulatory reference is § 91.703, which incorporates ICAO Annex 2 by reference. Annex 2, in turn, refers to ICAO Doc 7030, which requires State of the Operator or State of Registry approval for oceanic RNP operations. 6 See also Appendix G, Suggested Subjects for Inclusion in Oceanic and International Procedures and/or an Operations Manual.

communications, navigation, and surveillance capability codes appropriate to your aircraft and your operational authorization.

9. Specific airspace requirements, to include communications, navigation, and surveillance equipment requirements and specific approvals (OpSpecs/MSpecs/LOAs), as well as operational procedures related to Reduced Vertical Separation Minimum (RVSM) and RNP.

10. Long-range, air-to-ground communication procedures, including all data link and satellite communications (SATCOM) voice operations, as applicable.

11. En route and terminal procedures—differences from U.S. procedures.

12. Use of oceanic checklists.

13. Oceanic error risk mitigations.

14. Understanding of Strategic Lateral Offset Procedures (SLOP).

15. Air traffic clearances, to include proper terminology and phraseology.

16. Emergency and contingency procedures (see Appendix F, Special Procedures for In-Flight Contingencies in Oceanic Airspace), including required emergency equipment, SAR techniques, navigation equipment failure techniques (to include dead reckoning (DR)), and communication equipment failure techniques.

17. Specialized training, (e.g., if conducting operations in areas of magnetic unreliability (AMU), or for parts 121 and 135, ETOPS “preclude and protect” philosophy, as applicable).

18. Use of polar/remote area checklists.

19. Polar/remote continental terrain awareness, risk mitigations, and contingency options.

4.2 Performance-based Operations. › 4.2.2 RCP.

CHAPTER 4. COMMUNICATIONS, NAVIGATION, AND SURVEILLANCE

SYSTEMS GUIDANCE FOR OPERATIONS IN OCEANIC AND REMOTE

CONTINENTAL AIRSPACE

4.1 Communications, Navigation, and Surveillance Improvements—Impact on ATS.

4.1.1 Technological Advances. Technological advances in communications, navigation, and surveillance systems all contribute to an air traffic system that provides increased navigational accuracy and allows you and your aircraft to interact more quickly with controllers. These advances have also improved controller-pilot communications, navigation accuracy, and aircraft surveillance reporting. This enhanced communications, navigation, and surveillance capability greatly reduces the errors and retransmissions that hampered oceanic flights just a few years ago. These safety improvements have facilitated corresponding improvements in efficiency and capacity by reducing separation minima, allowing controllers to space aircraft closer together. Trials of new separation minima or implementations of new operating procedures are common in oceanic airspace. Operators should therefore make sure they have the most up-to-date information concerning the airspace in which they will be flying. U.S. and foreign State AIPs, NOTAMs, and related publications are normally the best sources of current information. International operations manuals that consolidate this information should be current.

4.1.2 ADS-B. ADS-B supports these improvements by providing a higher update and enhanced accuracy of surveillance information over the current radar-based surveillance systems.

4.1.3 Space-Based ADS-B. In 2019, a constellation of low-Earth orbit satellites with ADS-B receivers began supplying surveillance data to air traffic service providers (ATSP). Shortly thereafter, ICAO published a new separation standard for areas under ADS-B surveillance where VHF voice communications are not available. This new separation standard allows aircraft to be more closely spaced in oceanic areas, which in turn allows more efficient routing. While space-based ADS-B update rates are comparable to those of some domestic radar systems, communication systems traditionally used in oceanic and remote continental airspace do not perform as quickly as the VHF voice communications used in domestic environments. Consequently, aircraft cannot yet be spaced as closely as in domestic areas. As communication systems evolve, allowable separation between aircraft will likely be reduced further.

4.2 Performance-based Operations.

4.2.1 Measures of Performance. Performance-based operations rely on RCP, RNP, and RSP. It uses these three primary measures of performance to determine required separation between flights, both in radar contact and in oceanic and remote continental airspace. ATS providers determine separation requirements based on a combination of these three performance indicators.

4.2.2 RCP. RCP establishes aircraft/controller communications timeline, equipment, and flightcrew training standards. Generally, you can measure RCP in terms of the timeline required to complete the communication transaction and the continuity, availability, and

4.2 Performance-based Operations. › 4.2.3 RNP.

integrity of the transaction. In oceanic and remote continental airspace, RCP 240 and RCP 400 are the prevalent performance standards.

4.2.2.1 RCP 240 requires a 99.9 percent probability (continuity) the communications transaction will complete in less than 240 seconds (timeline). It also requires a 99.99 percent probability the communication can be initiated (availability) and no more than 10-5 communications transaction malfunctions per flight-hour (integrity).

4.2.2.2 RCP 400 requires a 99.9 percent probability (continuity) the communications transaction will complete in less than 400 seconds (timeline). It also requires a 99.9 percent probability the communication can be initiated (availability) and no more than 10-5 communications transaction malfunctions per flight-hour (integrity).

4.2.2.3 U.S. operators desiring Performance-based Communications and Surveillance (PBCS) approval for qualifying systems (e.g., with RCP 240 and RSP 180) can obtain OpSpec/MSpec/LOA A056, Data Link Communications. See paragraph 4.5 below.

4.2.2.4 For additional details, please refer to AC 90-117, Data Link Communications; and the ICAO Doc 10037, Global Operational Data Link (GOLD) Manual, Appendix B, RCP Specifications, and ICAO Doc 9869, Performance-based Communication and Surveillance (PBCS) Manual, at https://store.icao.int.

4.2.3 RNP. RNP establishes aircraft navigation accuracy, equipment, and flightcrew training standards. ICAO Doc 9613, Performance-based Navigation (PBN) Manual, outlines these standards. Generally, we measure these standards in terms of accuracy, integrity, continuity, availability, and functionality. Oceanic and remote continental airspace ATS providers primarily provide RNP 10 (also known as RNAV 10) and RNP 4-based separation minima. RNP 2 applications have also become available for oceanic and remote continental airspace, to be used by individual States as necessary to meet their airspace requirements. In all cases, ATS providers will apply appropriate separation minima between adjacent aircraft based on the capabilities each aircraft operator files in the flight plan. You must only indicate the oceanic RNP capability authorized in your OpSpec/MSpec/LOA B036, Oceanic and Remote Continental Navigation using Multiple Long-Range Navigation Systems.7

1. RNP 10 requires accuracy to be within 10 NM 95 percent of the time.

2. RNP 4 requires accuracy to be within 4 NM 95 percent of the time and within 8 NM 99.999 percent of the time.

3. RNP 2 requires accuracy to be within 2 NM 95 percent of the time and within 4 NM 99.999 percent of the time.

7 Regulatory reference is § 91.169, which refers to § 91.153. This requires the flight plan to include “any other information the pilot in command (PIC) or ATC believes is necessary for ATC purposes.”

4.3 Voice Communications in Oceanic Airspace. › 4.3.1 HF Radio Communications.

Note: Regardless of RNP value, pilots are expected to fly the centerline (or up to 2 NM right of course, where use of SLOP is authorized).

4.2.4 RSP. RSP establishes aircraft/controller surveillance timeline and equipment standards. Generally, you can measure RSP in terms of the timeline required to complete the transaction and the continuity, availability, and integrity of the transaction. In oceanic and remote continental airspace, RSP 180 and RSP 400 are the prevalent performance standards.

4.2.4.1 RSP 180 requires a 99 percent probability (continuity) the surveillance transaction will complete in less than 180 seconds (timeline). It also requires a 99.99 percent probability the communication can be initiated (availability) and no more than 10-5 communications transaction malfunctions per flight-hour (integrity).

4.2.4.2 RSP 400 requires a 99 percent probability (continuity) the surveillance transaction will complete in less than 400 seconds (timeline). It also requires a 99.9 percent probability the communication can be initiated (availability) and no more than 10-5 communications transaction malfunctions per flight-hour (integrity).

4.2.4.3 For additional details, please see ICAO Doc 10037, Appendix C, RSP Specifications.

4.2.5 Access to Performance-based Separation. Communications, navigation, and surveillance capabilities of aircraft and crew determine eligibility for authorizations (i.e., via OpSpecs, MSpecs, and LOAs), which in turn allow operators to take advantage of performance-based separation in oceanic and remote continental airspace. The significant improvements in communications, navigation, and surveillance systems have allowed air traffic controllers to reduce separation between aircraft, expanding access to more favorable routing and/or altitudes that offer savings in time and fuel.

Note: For a list of pertinent OpSpecs/MSpecs/LOAs, please see Appendix B, Special Areas of Operation and OpSpecs/MSpecs/LOAs.

4.3 Voice Communications in Oceanic Airspace. When operating over the high seas, ICAO Annex 2 requires you to maintain a continuous air-to-ground voice communication watch with the appropriate ATS authority on the appropriate communication channel.

Note: It is not acceptable to depend solely on other aircraft providing a radio relay to satisfy this requirement. The appropriate authority for the airspace where you conduct the flight may prescribe the aeronautical stations and frequencies used for two-way communications.

4.3.1 HF Radio Communications. HF radios have been in use for almost a century over oceanic and remote continental areas. As technological advances lead to more sophisticated methods of communication, HF equipment has also improved. HF radios now offer digital tuning, compact size, selective calling systems (SELCAL) (see paragraph 4.3.2

4.3.2 SELCAL. › 4.3.2.1 The SELCAL codes are controlled by a commercial service and are…

below), and new antenna concepts. Consider the following when using HF communications:

4.3.1.1 HF radio calls are typically made to a radio operator, who in turn electronically relays the information, via keyboard and pre-formatted messages, to air traffic controllers in oceanic centers. There is some delay between your requests and ATC clearances, where the radio operator coordinates with the appropriate controller. Radio operators do not have the authority to issue ATC clearances on their own.

4.3.1.2 Communications over HF radio rely heavily on proper radio terminology and scripted reports. Use the published guidance found in en route publications or the Aeronautical Information Manual (AIM) to make sure you deliver messages in the proper format. Speak at a moderate speed using the internationally accepted phraseology. You may find ICAO standard phraseology in ICAO Doc 9432, Manual of Radiotelephony. This document and other ICAO reference materials are available on ICAO’s website at https://store.icao.int.

4.3.1.3 If ATC uses the terms “expect” or “when can you accept,” they have not granted you a clearance. Typically, oceanic radio operators will use the phraseology “ATC clears…” when relaying a clearance.

4.3.1.4 ICAO Doc 4444, Procedures for Air Navigation Services—Air Traffic Management, requires the flightcrew to read back level instructions, heading and speed instructions, and ATC route clearances. Ensure that the radio operator acknowledges your exact read back to confirm that you correctly heard the instructions.

4.3.1.5 In general, higher frequencies (above 10.0 megahertz (MHz)) work better during daylight and lower frequencies (below 10.0 MHz) at night. It is common to use several frequencies on one flight while communicating with the same ATS provider.

4.3.1.6 HF communications are dependent on transmitted signals striking the ionosphere and reflecting back to antennae at ground stations. The ionosphere is susceptible to interference from space weather, resulting in periods where HF reception is marginal or unreadable. You may especially notice this phenomenon in polar regions above 60° N or below 60° S and during periods of significant solar activity.

4.3.2 SELCAL. SELCAL is a means to alert an individual aircraft that a ground station wishes to communicate with it. ATS providers can transmit SELCAL signals over VHF or HF. The signals produce an audio tone and possibly a cockpit indication that alerts you to initiate contact with the appropriate ATC unit.

4.3.2.1 The SELCAL codes are controlled by a commercial service and are assigned to a specific aircraft. Since the number of unique SELCAL codes is less than

4.3.3 SATVOICE. › 4.3.3.1 The FAA requires SATVOICE equipment supporting ATS…

the number of aircraft with SELCAL capability, multiple aircraft could be operating and logged in with the same SELCAL code assignment.

4.3.2.2 When you apply for SELCAL codes for your aircraft, the issuing company will de-conflict duplicate codes by region as much as possible. However, aircraft flying in multiple regions may encounter another aircraft using the same code. Therefore, you should be certain that the ATS radio operator uses your exact call sign when responding to a SELCAL.

4.3.2.3 New SELCAL systems use 32 tones, instead of only 16 tones currently used, and thereby increase the number of unique identifiers exponentially. The ICAO Communication Panel approved the global implementation of SELCAL 32 for revisions to take effect in November 2022. SELCAL 32 compliant equipment became available beginning in 2020. Operators with 16-tone HF SELCAL systems may continue to encounter a duplicate code situation.

4.3.2.4 Check HF SELCAL even when your CPDLC is working properly. You should do a SELCAL check prior to oceanic entry and then again at each control area (CTA) boundary. See the sample transcript of an HF SELCAL check below.

Sample Transcript of HF SELCAL Check

HF call from the air: “New York Radio, Airline 123, request SELCAL Check.”

Answer from the ground:

“Airline 123, New York Radio, roger.” [SELCAL tones transmitted]

HF call from the air: [If successful] “SELCAL check good, thank you!”

4.3.3 SATVOICE. In keeping with ICAO’s recognition of SATVOICE as a valid LRCS, the FAA accommodates SATVOICE through arrangements with the recognized Aeronautical Mobile Satellite (Route) Service providers. The FAA currently restricts direct SATVOICE contact between the pilot and FAA ATC to “distress and urgency situations,” or other exceptional circumstances only. For oceanic communications with ATC via New York Radio and San Francisco Radio, relevant SATVOICE policy and short codes are published in the U.S. AIP.

4.3.3.1 The FAA requires SATVOICE equipment supporting ATS communications to be installed in accordance with AC 20-150B (or subsequent edition), Airworthiness Approval of Satellite Voice (SATVOICE) Equipment Supporting Air Traffic Service (ATS) Communication.8 Additional

8 Regulatory references are § 91.703 and ICAO Annex 2, paragraph 3.6.5.1. The U.S. AIP, in describing the “appropriate communication channel,” invokes AC 20-150B.

4.3.3 SATVOICE. › 4.3.3.3 If SATVOICE is used (as authorized in the relevant AIP) as the…

requirements are listed in the U.S. AIP. Portable satellite phones are not approved for normal and routine ATC communications.

4.3.3.2 Additionally, the FAA requires a SATVOICE Callback Check when pilots use SATVOICE to communicate with ATC via New York Radio or San Francisco Radio. A sample transcript is here:

Sample Transcript of SATVOICE Callback Check

SATVOICE call from the air:

“New York Radio, Airline 123, request SATVOICE Callback Check.” For aircraft equipped with both Inmarsat and Iridium: “… on Inmarsat/Iridium (as applicable)”

Answer from the ground:

“Airline 123, roger, terminating call, will call you right back”

New SATVOICE call from ground:

“Airline 123, New York Radio with your SATVOICE Callback, how do you read?”

SATVOICE answer from the air:

“Loud and clear, SATVOICE Callback Check good, good day!”

4.3.3.3 If SATVOICE is used (as authorized in the relevant AIP) as the sole voice LRCS, for purposes of maintaining a continuous air-to-ground voice communication watch with the relevant ATS authority on the appropriate communication channel, several important considerations apply:

1. Flightcrews should be thoroughly familiar with SATVOICE use, to include the aural and visual alerts for incoming calls, call answering, display and selection of call priority, use of press-to-talk switches, call setup with or without the avionics phone book, call preemption, and call termination.

2. Avionics (e.g., flight management computer (FMC)) phone books should be organized in a logical, easy-to-understand manner, and flightcrews should have the appropriate number preloaded to facilitate rapid call setup with the relevant ATS authority. Calls should be managed to ensure a line is always available for an incoming “Operational High” priority (Priority 2/Q12) call from the relevant ATS authority.

3. For purposes of compliance with 14 CFR requirements on numbers of LRCS, the FAA recognizes SATVOICE as an approved LRCS only in areas where the ground infrastructure supports SATVOICE as the “sole voice LRCS.” Such services are described in the relevant AIP. In areas

lacking this designation, at least one operable HF (voice) radio is required.9

4.4 CPDLC and Automatic Dependent Surveillance-Contract (ADS-C). › 4.4.1 Title 14 CFR Requirements for LRCS.

4. As SATVOICE technology evolves, ensure that you comply with the latest guidance. In the United States, see entry in the U.S. AIP, with new changes published in the FAA’s International Notices. For additional guidance, refer to the FAA’s AIM, ICAO’s Satellite Voice Guidance Material (SVGM), and/or the relevant AIP.

4.3.4 Changes to Communications Procedures. Information needed on initial contact with an agency, radio frequencies, and other aspects of oceanic communications are changed frequently. Thus, it is important that you consult the appropriate AIP, international notices, current oceanic charts, and commercial en route publications for the most current information.

• ICAO NAT Doc 007, North Atlantic Operations and Airspace Manual, describes North Atlantic (NAT) operations, to include communication and navigation procedures in NAT airspace. The NAT section of ICAO Doc 7030, Regional Supplementary Procedures, currently requires HF SELCAL checks, meaning that an HF radio is required in NAT airspace.

• Commercially published navigation charts contain details of communication procedures on inserted panels. Exercise some caution in using this reference, as they may be on a different update cycle than the source documents and therefore could be not completely up to date.

4.4 CPDLC and Automatic Dependent Surveillance-Contract (ADS-C). Data link communications systems are widely used throughout the world and are normally used in concert with ADS-C systems that further improve ATS capability. CPDLC technology improves communications between aircraft and ATS providers. CPDLC replaces most of the often-challenging HF voice communications that were the only communication link with oceanic and remote continental airspace air traffic controllers for decades. With CPDLC, you and the controller transfer ATC clearance requests and instructions digitally, reducing the likelihood of miscommunication. CPDLC compliant with RCP 240 is required to fly the most efficient routes in the NAT.

Note: In ADS-C, C = “Contract.” The controller sets up one or more electronic contracts with your aircraft to automatically provide time-triggered (periodic) and/or condition-triggered (e.g., deviation event) reports. In addition, a controller, at any time, can issue a “demand” contract for a single periodic ADS-C report.

4.4.1 Title 14 CFR Requirements for LRCS. For purposes of compliance with 14 CFR requirements on numbers of LRCS (cited in paragraph 2.3.1 above), the FAA recognizes CPDLC that is compliant with RCP 240 as an approved LRCS. Equipage with CPDLC does not eliminate the requirement for at least one operable voice LRCS. This means that

9 Regulatory references are § 91.703 and ICAO Annex 2, paragraph 3.6.5.1. The applicable AIP describes the “appropriate communication channel.”

4.4 CPDLC and Automatic Dependent Surveillance-Contract (ADS-C). › 4.4.3 FAA Domestic CPDLC Use of Free Text in Route Uplinks.

(as is mentioned in paragraph 4.3.3.3, item 3) unless the relevant AIP authorizes SATVOICE as a sole voice LRCS, at least one operable HF (voice) radio is required.

4.4.2 Access to Preferred Airspace. Since equipment like CPDLC and ADS-C improves the efficiency with which aircraft in oceanic and remote continental airspace can be controlled, such better-equipped aircraft are being better served through initiatives to reserve preferred blocks of oceanic airspace for those aircraft. Preferred altitudes and routes around the world are more readily issued to aircraft equipped with robust communications, navigation, and surveillance capabilities.

4.4.3 FAA Domestic CPDLC Use of Free Text in Route Uplinks. The FAA’s domestic flight data processing systems automatically add so-called “Free Text” messages containing the entire cleared route, to all route clearance change messages. This allows pilots to more readily see and understand the given change. However, oceanic systems do not do this. The result is that pilots accustomed to the FAA domestic display of route clearances could be confused when seeing an oceanic route uplink. Figure 4-1, Sample CPDLC Route Uplinks, shows how a CPDLC route uplink might look if sent from a U.S. domestic system versus an oceanic system.

CHAPTER 4. › 4.5 Data Link Systems—Operational Authorization to Use.

Figure 4-1. Sample CPDLC Route Uplinks

4.5 Data Link Systems—Operational Authorization to Use. We grant operational authorization for operators to use Future Air Navigation System (FANS) data link (used in oceanic areas and in the U.S.) by issuing OpSpec/MSpec/LOA A056, as appropriate.10

Note: OpSpec/MSpec/LOA A056 also applies to VHF datalink communications in overland areas, such as Aeronautical Telecommunications Network (ATN) Baseline 1 (B1) (formerly Link 2000+), used in European airspace.

10 AC 90-117 provides information on OpSpec/MSpec/LOA A056.

4.6.1 Procedural Airspace. › 4.6.1.4 Controllers manage longitudinal separation in procedural…

4.5.1 Oceanic Data Link Requires Authorization. U.S. operators (including part 91) must have a data link authorization to file ATC flight plan capability codes J5 and/or J7 in oceanic airspace.11 These codes denote Inmarsat and Iridium satellite communications capability, respectively. You can find our guidance on the process and procedures for operational authorization and aircraft data link system approval in the following documents:

• AC 20-140, Guidelines for Design Approval of Aircraft Data Link Communication Systems Supporting Air Traffic Services (ATS).

• AC 90-117.

4.5.2 Data Link Requirements and Standards. You can consult ICAO Doc 10037 for additional information on data link requirements and standards.

4.6 ATC in Oceanic and Remote Continental Airspace.

4.6.1 Procedural Airspace. In oceanic and remote continental airspace, ATC typically requires position reports via voice or ADS-C, and controllers apply “procedural separation,” spacing aircraft farther apart than in domestic “ATS surveillance airspace” (where radar or ADS-B surveillance is accompanied by VHF voice communication with ATC). Space-based ADS-B provides significant improvements in surveillance, but without ATC being able to issue a vector via VHF voice communications, required separation between aircraft is greater. In areas with space-based ADS-B surveillance that lack direct VHF voice communications with the controller, ATC still therefore provides at least some elements of procedural control.

4.6.1.1 In procedural airspace, ATC issues clearances and instructions providing separation vertically and horizontally, based on the specific aircraft equipment authorizations you indicate on your flight plan.

4.6.1.2 ATC monitors your compliance with the issued clearance. Your aircraft position reports are processed for conformance with the clearance. If your aircraft is equipped with ADS-C, it provides trigger alerting for lateral and vertical deviations.

4.6.1.3 In order to make this procedural separation work the way it is designed, you must provide timely and accurate time estimates (estimated time of arrival (ETA)) and operate with strict discipline and adherence to ATC clearances and procedures, both normal and contingency.12

4.6.1.4 Controllers manage longitudinal separation in procedural airspace by assigning speeds, either true Mach number or true airspeed. Proper separation

11 AC 90-117 cites the regulatory basis for this requirement, which is § 91.123. 12 ICAO Annex 2, paragraph 3.6.2.2d), says: “if the time estimate … changes in excess of 2 minutes from that previously notified to air traffic services, … the flight crew shall notify the appropriate air traffic services unit as soon as possible.”

4.6.3 U.S. ATS. Information on provision of ATS by the United States is… › 4.6.3.2 Oceanic Airspace.

of aircraft is dependent upon pilots maintaining the speed assigned with the clearance (not to be confused with the speed filed on the flight plan).

• If traffic conditions permit, the controller may permit variations. However, if a controller assigns a speed, compliance with that speed is mandatory.

• Even when a controller permits variations, ICAO Annex 2 specifies that pilots must inform ATC of speed variations of Mach 0.02 or greater from the current flight plan (current clearance).

4.6.2 ICAO Procedures for Specific Geographical Areas. You will find detailed procedures for the applicable ICAO Region in ICAO Doc 7030. When flying over the high seas (international airspace, generally greater than 12 NM from the nearest shore), part 91, § 91.703 requires compliance with Annex 2. Annex 2, in turn, refers to Doc 7030. You should consider ICAO Doc 7030 regulatory.

4.6.3 U.S. ATS. Information on provision of ATS by the United States is available in FAA Order JO 7400.11, Airspace Designations and Reporting Points. Also refer to 14 CFR part 71.

4.6.3.1 Domestic Airspace. (ICAO refers to this as “Continental” Airspace). Along the coast of the United States, domestic ATC procedures (with radar or ADS-B surveillance and VHF communications) are applied in U.S. Offshore Airspace, generally extending as far as the useful range of radar and VHF communications systems permits, approximately 150-200 NM from the coast.

Note: Domestic airspace generally includes sovereign airspace over terrain and territorial waters, as well as the “high seas” airspace beyond 12 NM from the coast with ATS surveillance and VHF communications. As discussed in paragraphs 2.3.2 and 2.3.3, part 91 subpart B applies in U.S. sovereign airspace, and ICAO Annex 2 applies in “high seas” airspace.

4.6.3.2 Oceanic Airspace. The United States provides ATS in oceanic airspace as follows:

• Atlantic Ocean: New York, Miami, and San Juan Flight Information Regions (FIR).

• Gulf of Mexico: Miami and Houston Oceanic CTAs/FIRs. Most of the Gulf of Mexico is under ADS-B surveillance, with VHF voice communications directly with the controller (above 18,000 ft mean sea level (MSL)).

• Pacific Ocean: Oakland and Anchorage CTA/FIR.

• Arctic Ocean: Anchorage Arctic CTA/FIR.

4.7 Special Use Airspace (SUA). › 4.7.2 Prohibited Areas.

4.6.3.3 Remote Continental Airspace. The United States provides ATS in remote continental airspace as follows: Alaska Remote Continental Airspace: Anchorage Air Route Traffic Control Center (ARTCC).

4.6.4 Advanced Technologies and Oceanic Procedures (ATOP). U.S. controllers use the ATOP flight data processing system in the airspace of Oakland Oceanic, New York Oceanic, and Anchorage Oceanic and Arctic FIRs.

4.6.4.1 Within this airspace, ATOP allows for establishing the separation minima for all pairs of aircraft along a cleared profile, and provides aircraft profile conformance monitoring and protection.

4.6.4.2 ATOP deciphers ATC flight plan information to determine what separation standards may be applied to a particular aircraft based on filed aircraft equipage. Accordingly, you must notify ATC immediately if your communications, navigation, and surveillance equipment capability degrades below that which you listed in your flight plan.13

4.6.4.3 ATOP analyzes cleared routes of aircraft and alerts controllers of potential future conflicts (scalable to more than 2 hours ahead) with other aircraft. ATOP also considers different separation standards applied by adjacent ATC facilities and can warn the controller when a conflict will occur based on the adjacent ATC facility’s requirements. This allows controllers to effectively plan for transitions to adjacent FIRs.

4.6.4.4 You can find specific information regarding ATC separation standards in FAA Order JO 7110.65, Air Traffic Control. Additionally, trial periods where new separation standards are being applied will be announced on the FAA’s International Notices website.

4.7 Special Use Airspace (SUA).

4.7.1 Warning Area. A warning area, as defined in 14 CFR part 1, § 1.1, is airspace of defined dimensions extending from 3 NM outward from the coast of the United States that contains activity that may be hazardous to nonparticipating aircraft. The purpose of such a warning area is to warn nonparticipating pilots of the potential danger. A warning area may be located over domestic or international waters or both.

4.7.2 Prohibited Areas. ICAO Annex 2 specifies that these areas exist “above the land areas or territorial waters of a State, within which the flight of aircraft is prohibited.”

13 Regulatory reference is § 91.169, which refers to § 91.153. This requires the flight plan to include “any other information the pilot in command or ATC believes is necessary for ATC purposes.” The U.S. AIP states that pilots must “advise ATC” if equipment failures render the filed capability indicators inaccurate.

4.9 World Geodetic System 1984 (WGS 84). › 4.9.1 Operations in Areas That Are Not WGS 84-Compliant.

4.7.3 Restricted Areas. ICAO Annex 2 specifies that these areas exist “above the land areas or territorial waters of a State, within which the flight of aircraft is restricted in accordance with certain specified conditions.”

Note: Carefully review charts for these types of areas when you plan your flight, taking note of the area operating times and restrictions. You should also review applicable oceanic NOTAMs.

4.8 Air Defense Identification Zones (ADIZ). Title 14 CFR Part 99, Security Control of Air Traffic, discusses defense areas and ADIZ. You can check part 99, the latest U.S. AIP, the latest AIM (chapter 5, section 6), and all FAA NOTAMs Domestic/International to ensure compliance with national security requirements in the ADIZ.

4.9 World Geodetic System 1984 (WGS 84). ICAO and the United States endorse the WGS 84 or approved equivalent as the geodetic reference datum standard for air navigation latitude and longitude coordinates. WGS 84 provides for a common geodetic reference system and a means to standardize aeronautical surveys and related products. You should determine in advance whether any countries you intend to fly over or into are WGS 84-compliant. Information about WGS 84 compliance is often noted on charts used in terminal operations or on airfield diagrams. A State’s AIP generally notes compliance with WGS 84. Most areas of the world are listed as: 1) Unknown (U); 2) Partially Compliant (PC); 3) Compliant (C); or 4) Noncompliant (NC) with WGS 84.

Note: Commercial charting vendors also post information on their websites about specific countries and their compliance with WGS 84.

4.9.1 Operations in Areas That Are Not WGS 84-Compliant. Flight manuals may include a note for RNAV systems indicating that, for countries or terminal areas that are not WGS 84-compliant, the crew should deselect the use of Global Navigation Satellite Systems (GNSS), and use ground-based navigation aids for navigation. You should be familiar with your flight manual limitations as well as any country-specific procedures published in State AIPs when flying in countries or terminal areas that are not WGS 84-compliant.

5.2 Preparing an Itinerary. › 5.2.1 Itinerary Factors.

CHAPTER 5. FLIGHT PLANNING GUIDANCE FOR INTERNATIONAL AND

OCEANIC AND REMOTE CONTINENTAL AIRSPACE OPERATIONS

5.1 Lead Time Requirements.

5.1.1 Preparation. Your preparation for a successful oceanic and remote continental and/or international flight, whether you fly large or small aircraft, starts with adequate training and planning. The lead time required for planning varies depending on such things as experience, training, and currency, as well as specific country requirements, and could exceed 30 days. Dispatch/flight locator departments of 14 CFR part 121 operators and large 14 CFR part 135 operators with good familiarity and experience with such flights can sometimes work with shorter lead times. Commercial flight planning companies used by 14 CFR part 91 and smaller part 135 operators can offer similar services.

5.1.2 Awareness. Ensure you are aware of current and special notices relating to entry and overflight requirements for the countries on your itinerary. In most cases outside North America and Europe, you obtain prior permission to land in or overfly a country directly from that country’s Civil Aviation Authority (CAA). You can also find information on immunizations, ports of entry, and other important requirements in the country’s AIP and in various commercial publications.

5.1.3 Verification. You should allow enough lead time to ensure your planning is thorough, complete, and correct. You should also cross-check and verify any flight planning products against the appropriate source documents. By doing so, you could uncover potential errors before they result in a pilot deviation.

5.2 Preparing an Itinerary.

5.2.1 Itinerary Factors. You should consider the following questions when developing your itinerary:

1. What airspace, routes, speeds, and altitudes, do I fly to get to my destination(s)?

2. Are there any terrain clearance concerns along those routes at those altitudes?

3. Is the flying time to suitable and available en route alternates from along those routes and altitudes appropriate for the aircraft and operating part? (Plotting ETPs will help answer this question.)

4. Are there any pitfalls I should be aware of from each State’s AIP?

5. What communications, navigation, and surveillance equipment and authorizations must I have in order to fly my intended routes and altitudes?

6. Will I be operating in an SAO? Do I have the necessary operational authorization(s) to do so? (See Appendix B, Special Areas of Operation and OpSpecs/MSpecs/LOAs, Table B-1, SAO-Related OpSpecs/MSpecs/LOAs.)

7. With regard to my GNSS equipment, are there any WGS 84 compliance issues in countries I intend to transit? (Paragraph 4.9 provides information on WGS 84.)

5.2 Preparing an Itinerary. › 5.2.2 Administrative, Country-Specific Issues and Requirements.

8. What survival equipment must I have on board in order to fly my intended routes?

9. Are there suitable en route and destination alternates available in the event of an emergency diversion at other than my intended en route altitude? Are there terrain clearance or oxygen considerations at those divert altitudes?

10. Does my preferred destination have instrument approaches and arrival and departure procedures that are compatible with my aircraft equipment and authorizations?

11. What crew rest requirements will I have for each destination?

Note: See paragraph 5.3 below regarding fatigue management issues.

12. Should I use a flight planning or dispatch service for my trip?

13. Have I reviewed the following:

• Oceanic error mitigation procedures?

• Oceanic flight planning, plotting charts, navigation, and waypoint procedures?

• My oceanic checklist?

• SLOP?

• En route procedures for all airspace I will pass through?

• Oceanic contingency procedures?

14. Are there specific pilot certification, type rating, and/or medical certificate requirements for the countries I’ll be visiting? Are single-pilot operations authorized?

15. Will my intended route take me through areas of volcanic activity?

16. If my route takes me through polar areas, have I researched the risks inherent to operations on polar routes? (Paragraph 5.10 provides information on polar operations.)

17. ETOPS consideration: Will I be operating more than 60 minutes (part 121) or more than 180 minutes (part 135) from an Adequate Airport?

5.2.2 Administrative, Country-Specific Issues and Requirements. As part of your itinerary preparation, asking the following additional questions can help you determine the country-specific issues/airspace requirements that might affect your international flight:

1. Do I require overflight and landing permits for any of the airspace/airfields I will transit?

2. How much will overflight and landing fees cost, and how do I pay for each airspace and destination I intend to transit (e.g., credit card, cash, local currency, U.S. currency)?

3. How much advance notification do I need to provide prior to arrival?

Note: All countries require some form of advance notification of arrival. You should carry a copy of the advance notification, as well as confirmation that the

notification was sent. This is particularly important for countries that do not normally return approvals.

5.2 Preparing an Itinerary. › 5.2.3 Airport-Specific Issues.

4. What are the availability, types, and duration of visas, tourist cards, and other required entry documents for all countries I intend to visit, as well as those with potential alternate airports (in the event I have to divert)?

Note: Some countries require that you have a visa for the next country of entry before departure, as well as proof of required immunizations for that country. You can obtain this information from the U.S. Department of State (DOS).

5. Are there prohibitions, restrictions, notices, and/or applicable travel advisories for countries I intend to visit?

Note: The FAA’s website includes a special section on prohibitions, restrictions, notices, and DOS travel advisories applicable to foreign countries at https://www.faa.gov/air_traffic/publications/us_restrictions/. This is a particularly important aspect of your flight planning.

6. What is the normal work week for countries I intend to overfly/enter?

Note: Understanding this will help you coordinate for visas and overflight/landing permits. You can obtain this information from the DOS.

7. Are there any import regulations I need to consider, given the amount of time I intend to remain in the countries on my route?

Note: Aircraft that remain within the territorial limits of a country for an extended period may become subject to import regulations and impoundment.

8. What hours are customs, immigration, and other services operational?

9. Do I intend to conduct any operations that might be considered “cabotage?”

5.2.3 Airport-Specific Issues. Consider the following airport-specific issues when planning for your overseas trip:

1. What time considerations can affect your trip?

• What is local time at each of my destination airports in terms of Coordinated Universal Time (UTC)?

• What is local time at my original departure airport?

• Are there restrictions on operating at night in the countries I intend to transit?

• Do any of the airspaces/destinations I intend to transit require slot times?

2. Is a Prior Permission Only (PPO) number required for landing?

3. Do my preferred destination and alternate airfields have the appropriate grade of fuel and other types of aircraft handling services available?

4. Are maintenance services available at my destination airfields?

5. Should I bring spare parts for my aircraft?

6. Will I have lodging available at the destination?

CHAPTER 5. › 5.4 Required Paperwork/Documentation.

5.3 Crew Fatigue.

5.3.1 Fatigue Management. International travel typically involves crossing time zones and interrupting normal sleep patterns (circadian rhythm). Ensure you have a plan for how you will manage fatigue for you and your crew.

5.3.2 Fatigue Management Strategies. AC 120-100, Basics of Aviation Fatigue, discusses strategies to mitigate the effects of fatigue and is an excellent resource. AC 120-103, Fatigue Risk Management Systems for Aviation Safety, discusses the Fatigue Risk Management Systems (FRMS) prescribed in 14 CFR part 117. While part 117 does not apply to all operators, we recommend you review both ACs as the contents cover issues that are important to all aircrews. Although a Fatigue Risk Management Plan (FRMP) is only required for part 121 operators, the FAA recommends any operator who frequently conducts long-range flights to objectively assess the risks of flightcrew fatigue and implement some form of a plan to reduce those risks.

5.3.3 Self-Care and Time Zone Differences. Having a high level of physical fitness, using caffeine strategically, and avoiding alcohol can help you adjust to time zone differences, allow your body to rest better, and help make you a more effective, safer operator.

5.3.4 Preparing to Mitigate Fatigue. Inquire in advance about day sleeping or noise levels in the location where you intend to get your crew rest. This will help your crewmembers know what challenges to good rest might lie ahead. You should also consider adding pilots for long-duration flights or those outside of normal sleep times. This will help mitigate fatigue issues and promote safer flying.

5.3.5 Sleep Aids. Make sure you understand the restrictions on using sleep aids and the importance of consulting an Aviation Medical Examiner (AME) prior to use. They will advise you on the possible side effects of sleep aids. We have built a list of approved prescription sedative-hypnotic-type drugs approved for use under certain conditions.

• Information regarding pharmaceutical sleep aids is available on the FAA’s website.

• This website includes names of many popular sleep aids. It also includes the required wait time after taking the last dose before you can fly (“pill to push” time).

5.4 Required Paperwork/Documentation. Whenever you fly into, from, or over foreign territory, you must comply with that territory’s regulations. Ensure that you have all required entry documents available for presentation upon arrival; you may need to provide multiple copies of each.

5.4.1 Documentation. › 5.4.1.1 Aircraft/Aircrew Documentation.

5.4.1 Documentation. Local authorities may ask to see the below-listed types of paperwork. The Articles of the Chicago Convention specify those items marked with a double plus sign (++).

5.4.1.1 Aircraft/Aircrew Documentation. It is important to note that you may be responsible for additional documentation requirements that this list does not include.

1. Airworthiness certificate.++

2. Aircraft registration++ (some States do not allow temporary certificates).

3. Radio station license.++

• ICAO Annex 6 Part I requires that one member of the flightcrew hold a valid radio telephone operator’s license “authorizing operation of the type of radio transmitting equipment to be used.”

• The European Union Aviation Safety Agency (EASA) has published inspector guidance for its Ramp Inspections program that references the requirement in Article 30 of the Chicago Convention at https://www.easa.europa.eu/sites/default/files/dfu/SAFA%20Ramp%2 0Inspections%20Guidance%20Material%20-%20Version%202.0.pdf. Some operators have found it useful to create a ramp inspection binder for easy access to required documents.

• For U.S. domestic flights operating only on VHF, the Federal Communications Commission (FCC) does not require the license.

4. Minimum equipment list (MEL) (or Master Minimum Equipment List (MMEL) if operator plans to operate under this option).

5. Airplane Flight Manual (AFM) with Weight and Balance (W&B) information and metric conversion tables, if applicable.

6. Copies of aircraft and engine logbooks.

7. Import papers for aircraft of foreign manufacture.

8. OpSpecs/MSpecs/LOAs.

Note: Some countries require an OpSpec/MSpec/LOA and/or an airworthiness statement for certain operations.

9. Ownership papers.

10. Certificates of insurance, if applicable.

11. Authorization letters from the operating company or the aircraft owner (original signature required), if applicable.

Note: For privately owned aircraft where the owner is not on board, many countries require a letter from the owner before they will allow operations within their country (you can find specific information on

5.4.1 Documentation. › 5.4.1.3 Personal Documentation for Crew and Passengers.

this letter and other requirements in the AIP of the countries concerned).

12. Licenses.

13. Crewmember certificates.++

Note: Pay special attention to medical certificates, as expiration rules vary from country to country; consult the AIP for those countries where you intend to land.

5.4.1.2 Trip-Specific Documentation. The following information will change for each flight, but should be available for authorities:

1. Passenger manifest, containing complete names of passengers and places of embarkation and destinations of each.++

2. Cargo manifest and detailed declaration of the cargo, if carried.++

3. Copies of overflight and landing permissions.

4. General declarations.

5. Journey logbook, signed by the pilot in command (PIC). ++ ICAO Annex 6 identifies the components of the journey logbook as listed below. Consult the AIP for the country you are visiting for their particular requirement.

• Airplane nationality and registration.

• Date.

• Names of crewmembers.

• Duty assignments of crewmembers.

• Place of departure.

• Place of arrival.

• Time of departure.

• Time of arrival.

• Hours of flight.

• Nature of flight (private, aerial work, scheduled, or nonscheduled).

• Incidents and observations, if any.

• Signature of person in charge.

5.4.1.3 Personal Documentation for Crew and Passengers. When planning a trip to or from a foreign country, ensure that all travelers have proper personal documentation (passports and visas, as required). You may find the requirements for individual countries at https://travel.state.gov/.

5.7 Weather Forecasts and Other Meteorological Planning. › 5.7.1 National Weather Service (NWS).

5.5 Entry to Foreign Airspace—Flight Plan vs. Formal Advance Permission.

5.5.1 Permission for Airspace Entry. When the foreign ATS authority accepts your flight plan and issues you a flight clearance, you have not necessarily received official approval for entering that State’s airspace. The governing CAA may independently require permission for airspace entry, and your destination airfield may require permission as well.

5.5.2 Flight Plans. Your flight plan provides advance notice of foreign airspace penetration and facilitates effective ATC procedures. For some countries, your flight plan is the only advance notice required; other countries use your flight plan as a check against previously granted permission to enter national airspace.

5.5.3 State AIPs. During your pre-trip planning, as noted in paragraphs 5.1.2, 5.2.1, and 5.2.2 above, consult the AIP for the States you will transit to determine any overflight/landing permits and whether prior permission is required. Ensure you allow plenty of lead time to request and obtain all necessary permissions.

5.6 Managing Risk in Oceanic and Remote Continental Airspace Operations. Operators should have a risk management process before conducting oceanic operations (per ICAO Annex 19, originally issued in 2013). Many of the topics included in earlier portions of this chapter should be included as elements of your risk assessment. Operators are strongly encouraged to research the information available on the FAA website, both from the standpoint of oceanic operations planning, and risk management overall. Non-airline operators are also encouraged to review the material specifically earmarked for airline operators. You can get good ideas from that information.

Note: The Automated Mutual-assistance Vessel Rescue (AMVER) system, sponsored by the U.S. Coast Guard (USCG), is a computer-based voluntary global ship reporting system used worldwide by SAR authorities to arrange for assistance to persons in distress at sea. The web address is: https://www.amver.com/. Operators conducting oceanic operations are encouraged to be familiar with AMVER in case of a potential ditching. Once the operator notifies ATC of a possible ditching, all merchant vessels registered with AMVER and within 100 NM of the aircraft’s predicted ditching position will be notified.

5.7 Weather Forecasts and Other Meteorological Planning.

5.7.1 National Weather Service (NWS). The NWS provides weather, hydrologic, and climate forecasts and warnings for the United States, its territories, adjacent waters, and ocean areas. Parts 91 subpart K (part 91K), 121, and 135 operators must use an approved weather source (i.e., NWS or FAA-approved).14

14 Regulatory references are §§ 91.1039, 121.101, and 135.213.

CHAPTER 5. › 5.9 ETOPS.

5.7.2 Weather Sources. As representatives of the Administrator, Principal Operations Inspectors (POI) may approve, via OpSpec/MSpec A010, Aviation Weather Information (required for parts 91K, 121, and 135) the following weather sources:

• The NWS for the United States and its territories.

• U.S. and North Atlantic Treaty Organization (NATO) military observing sources.

• Meteorological offices or automated observations operated by ICAO Member States (as long as the States subscribe to ICAO meteorological standards and practices (i.e., list no differences to ICAO Annex 3)).

• Members of the World Meteorological Organization (WMO).

5.7.3 Enhanced Weather Information Systems (EWINS). Many certificated operators utilize an EWINS. EWINS are systems for gathering, evaluating, and disseminating aviation weather information, and for issuing weather reports and forecasts prepared by properly trained and qualified aviation meteorologists or aircraft dispatchers. Air carriers typically use a proprietary EWINS. Parts 91K, 121, and 135 operators require FAA approval via OpSpec/MSpec A010 to use EWINS.15

5.7.3.1 Each carrier’s EWINS must have sufficient procedures, personnel, and communications and data processing equipment to effectively obtain, analyze, and disseminate aeronautical weather data. An EWINS source may produce weather analyses and forecasts based on meteorological observations provided by the Federal government.

5.7.3.2 For an explanation of EWINS, refer to FAA Order 8900.1, Volume 3, Chapter 26, Section 4, Enhanced Weather Information Systems. Approval to use EWINS weather products is issued on a case-by-case basis and is currently only applicable to part 91K program managers and part 121 or 135 certificate holders (CH), who may either act as their own EWINS or contract for services from an outside source. These approved operators may conduct flight operations using the weather analyses and forecasts produced by their approved EWINS.

5.8 FAA International Notices Website. International Notices include Flight Prohibitions Notices and International Oceanic Airspace Notices that could affect your decision to enter or use certain areas of foreign or international airspace. If you are seeking to enter areas of the world that require special considerations, these notices can be very important. To access FAA International Notices, refer to https://www.faa.gov/air_traffic/publication s/internationalnotices/.

5.9 ETOPS. ETOPS (the ICAO term is “Extended Diversion Time Operations (EDTO)”) requirements pertain to aircraft operated under parts 121 and 135. ETOPS is a system of maintenance, planning, alternate airport selection, dispatch, and flight operations standards that are designed to preclude a diversion and, if one were to occur, to protect

15 Regulatory references are §§ 91.1039, 121.101, and 135.213.

5.11 Areas With Limited or No ATS (Also Called “NO FIR” Areas). › 5.11.1 Part 91 Operators.

that diversion. Thus, ETOPS standards establish a higher level of performance requirements and equipment monitoring.

Note: Rules covering ETOPS do not address operations conducted under part 91. However, because risk increases with distance from an Adequate Airport (defined in § 121.7), if you are a GA operator, we strongly recommend that your pilot training, maintenance practices, flight planning, and any applicable dispatch procedures follow the processes and procedures established in ETOPS regulations and guidance.

5.9.1 ETOPS Guidance. Guidance pertaining to ETOPS is provided in AC 120-42, Extended Operations (ETOPS and Polar Operations), and AC 135-42, Extended Operations (ETOPS) and Operations in the North Polar Area. The regulatory basis for ETOPS requirements is provided by part 121 (§§ 121.161 and 121.374 and appendix P) and part 135 (§ 135.364 and appendix G).

5.10 Polar Operations. ACs 120-42 and 135-42 cover polar operations by aircraft operated under parts 121 and 135 respectively. As noted in the ETOPS discussion above, we strongly recommend part 91 operators refer to these ACs if you fly a polar route. Other worthwhile sources of information include the Canada and Iceland AIPs and the Canadian Designated Airspace Handbook. The North Polar Area of Operations includes the area that lies north of latitude 78° N. The North Polar routes across Russia are shown in the Russian AIP or in commercial charts for Eastern Europe and Eurasia. The South Polar Area of Operations includes the area south of latitude 60° S. Operators should contact a specialist from the FAA’s Flight Technologies and Procedures Division, Flight Operations Group for advice on operational factors to consider when planning polar operations.

1. Relevant authorizations are:

a. OpSpec/MSpec B055, North Polar Operations.

b. OpSpec/MSpec B040, Operations in Areas of Magnetic Unreliability.

2. Operations in AMUs when using a Global Positioning System (GPS)-only navigation-sensor for the flight management system (FMS) require careful analysis to confirm that the FMS is receiving accurate and reliable heading information.

5.11 Areas With Limited or No ATS (Also Called “NO FIR” Areas). Two examples of such areas are the boundary between Bodo Oceanic and Murmansk, and the area southeast of Mazatlan's Oceanic FIR off the west coast of Central America.

5.11.1 Part 91 Operators. While part 91 GA operators are not bound by the requirements below, we recommend that they have a solid understanding of this information before attempting to operate in this type of airspace. If you intend to operate in advisory-only airspace, you are required, as you are for all flights, to become familiar with all available information

5.12 Rotorcraft Operations. › 5.12.3 Helicopter Offshore Instrument Operations.

concerning that flight.16 Good familiarity with applicable operating procedures allows for safe operations.

5.11.2 Certificated Operators. To operate in uncontrolled information regions, certificated operators must be issued OpSpec/MSpec A014, Special En Route IFR Operations in Class G Airspace, in accordance with § 91.1015; § 121.93; § 121.113; part 125, § 125.31; or § 135.215, as applicable. In uncontrolled airspace, you will not have access to ATC, air traffic advisory, flight information, and alerting services. In approving routes outside controlled airspace via OpSpec/MSpec A014, the Administrator makes a determination that traffic density is such that an adequate level of safety can be assured. FAA inspectors will also evaluate whether you have acceptable alternative means to ensure the following:

1. You can notify the appropriate organization in a timely manner should you require SAR assistance.

2. You have a method to access changes in SIGWX information in a timely manner.

3. Those navigation facilities necessary for you to safely conduct the operation are available and serviceable. You can receive updates regarding the serviceability of the required Navigational Aids (NAVAID).

4. You have reliable in-flight information concerning other IFR aircraft operating near your route of flight (e.g., Traffic Alert and Collision Avoidance System (TCAS) and/or ADS-B In). This could also include “broadcast in the blind” procedures and other “expected” practices (see Appendix E, IATA In-Flight Broadcast Procedure, as well as ICAO Annex 11’s description of traffic information broadcasts by aircraft (TIBA)).

5.12 Rotorcraft Operations.

5.12.1 FAA and ICAO Requirements. The guidance on U.S. and International Regulations in Chapter 2, Background Information for Operations in Oceanic and Remote Continental Airspace, also applies to helicopter operations in oceanic and remote continental airspace.

5.12.2 Offshore Helicopter Operations. AC 90-80, Approval of Offshore Standard Approach Procedures, Airborne Radar Approaches, and Helicopter En Route Descent Areas, contains detailed information on offshore helicopter operations, both instrument and ATS surveillance (ADS-B or radar). It also provides instruction on how you can gain authorization to conduct such operations.

5.12.3 Helicopter Offshore Instrument Operations. OpSpec/MSpec/LOA H104, Helicopter Offshore Instrument Operations: Offshore Standard Approach Procedure (OSAP), Airborne Radar Approach (ARA), and Helicopter En Route Descent Area (HEDA) Operations, is available to authorize en route descent procedures under IFR.

16 Regulatory references are § 91.103, Preflight action, and ICAO Annex 2, Chapter 2, Applicability of the Rules of the Air, Paragraph 2.3.2, Pre-Flight Action.

5.12 Rotorcraft Operations. › 5.12.4 Helicopter Part 135 Proving and Validation Tests.

5.12.4 Helicopter Part 135 Proving and Validation Tests. Section 135.145 is relevant for rotorcraft operations in oceanic and remote continental airspace. You may develop proposed routes using NAVAIDs where you have adequate signal coverage available. In areas where signal coverage is not available, you must provide a suitable means of navigation. We may require a validation test in VFR conditions to ensure that you are able to demonstrate adequate navigational performance for the route(s) before granting approval for your use of the route(s).

6.1.2.1 Large Height Deviation (LHD). › 6.1.2.1.1 The most common causes of LHDs are:

CHAPTER 6. FLIGHT EXECUTION GUIDANCE FOR OPERATIONS IN OCEANIC

AND REMOTE CONTINENTAL AIRSPACE

6.1 General Information. The main focus of this guidance is operations in oceanic airspace. The guidance is also applicable to some operations in remote continental airspace, where LRCSs are used.

6.1.1 Checklists. In Appendix D, Sample Oceanic Checklist, we have included a sample oceanic checklist tailored from the ICAO version, in both condensed and expanded forms. The checklist is designed to encourage an orderly task flow and reduce oceanic vertical, lateral, longitudinal, and timing navigation errors. Similar to the ICAO version, the checklist in this AC represents lessons learned from many years of flight in oceanic airspace, along with internationally accepted best practices for such operations.

Note: You may tailor the abbreviated and expanded checklists to your specific needs and operational circumstances. Until you are experienced and familiar with all items on your tailored checklist, we recommend you refer to your expanded checklist to ensure you follow the procedures in their entirety.

6.1.2 Pilot Deviations—Common Causes. Technological advances in communications, navigation, and surveillance equipment have enabled aircraft to operate with ever-improving precision and accuracy. However, despite these improvements in capability, pilots continue to deviate from their current route clearances.

Note: The NAT ICAO Region publishes the Oceanic Error Safety Bulletin (OESB), which is an excellent resource for understanding how to prevent common errors. The current OESB can be found in the “EUR and NAT Documents” area of the ICAO website, in the “NAT OPS Bulletins” folder: https://www.icao.int/EURNAT/Pages/EUR-and-NAT-Document.aspx.

6.1.2.1 Large Height Deviation (LHD). An LHD occurs when an aircraft is 300 feet or more off its assigned altitude. LHDs increase the risk of mid-air collision.

6.1.2.1.1 The most common causes of LHDs are:

1. ATC loop errors:

• Misunderstood or miscommunicated clearances.

• Inadequate ATC coordination.

2. Pilot deviations from assigned altitude:

• Following the flight plan rather than a clearance or revised clearance.

• Erroneous altitude programming in the FMS, such as a mistake in the step-climb entry.

• Misinterpretation/misapplication of conditional clearances.

6.1.2.1 Large Height Deviation (LHD). › 6.1.2.1.2 Data indicates that a majority of crew-related errors involve…

• Improper execution of contingency procedures.

• Turbulence encounters.

6.1.2.1.2 Data indicates that a majority of crew-related errors involve misinterpretation or misapplication of “conditional clearances.” Conditional clearances improve the efficient utilization of airspace, allowing ATC to assign altitudes that enable lower fuel burn. Event reports from ATC and flightcrews indicate that pilots misapply terms in the clearance such as “BY” or “AT”—terms, which have completely different meanings. See Table 6-1 below for examples of incorrectly applied conditional clearances.

Table 6-1. Examples of Incorrectly Applied Conditional Clearances

CLEARANCE CREW ACTION CORRECT ACTION

Via CPDLC at 1714, crew conditionally cleared, “maintain F340, at 1725 climb to and maintain F360, climb to reach F360 by 1735, report level, due to traffic.”

Crew initiated climb early, reported (ADS-C) passing F354 at 1721.

Crew should have delayed commencing climb until 1725, and planned to reach F360 by 1735.

Via CPDLC, crew at F380, cleared F390 to cross 66N040W level.

Continue reading ↓ 120 of 321 passages shown