Radar Vectors
Advisory Circular Current Issued Jun 13, 2008 AFS-220 70 pages Copy saved Nov 18, 2026

AC 120-42B Extended Operations (ETOPS and Polar Operations)

States an acceptable means but not the only means for obtaining approval under FAR Section 121.161 for two-engine airplanes to operate over a route that contains a point farther than one hour flying time at the normal one-engine inoperative cruise speed (in still air) from an adequate airport.

Official source ↗ Open PDF

SL--. Advisory U.S. Department of Transportation Federal Aviation Circular Administration

Subject: Extended Operations (ETOPS and Date: 6/13/08 AC No: 120-42B Polar Operations) Initiated by: AFS-220 Change:

FOREWORD

This advisory circular (AC) provides certificate holders with guidance for obtaining operational approval to conduct Extended Operations (ETOPS) under Title 14 of the Code of Federal Regulations (14 CFR) part 121, §121.161. The Federal Aviation Administration (FAA) may authorize ETOPS with two-engine airplanes over a route that contains a point farther than 60 minutes flying time from an adequate airport at an approved one-engine inoperative cruise speed under standard conditions in still air (adequate airport is defined in part 121, § 121.7 and Appendix 1 of this AC). The FAA may also authorize ETOPS with passenger-carrying airplanes with more than two engines over a route that contains a point farther than 180 minutes flying time from an adequate airport at an approved one-engine inoperative cruise speed under standard conditions in still air. This AC provides guidance for obtaining authorization to conduct operations under part 121 in Polar Areas as well.

This AC provides an acceptable means of complying with the regulations; however, it is not the only means of compliance. When this AC uses mandatory language (e.g., "must" or "may not") it is quoting or paraphrasing a regulatory requirement or prohibition. When this AC uses permissive language (e.g., "should" or "may"), it describes an acceptable means, but not the only means, of obtaining operational approval to conduct ETOPS under § 121.161 of the regulations.

ORIGINAL SIGNED by

James J. Ballough Director, Flight Standards Service

CONTENTS

Paragraph Page

CHAPTER 1. GENERAL 1 100. Applicability 1 101. Cancellations 1 102. Related Regulations 1

CHAPTER 1. GENERAL 1 100. Applicability 1 101. Cancellations 1 102. Related Regulations 1

CHAPTER 2. BACKGROUND ON ETOPS 3 200. ETOPS Regulatory Requirements 3 201. Evolution of ETOPS 3 202. ETOPS Applicability to All Passenger-Carrying Airplanes Flown in Long-Range Operations 5 203. "Extended Operations" 6 204. Preclude and Protect 7 205. ETOPS Areas of Operation 8 206. ETOPS Alternate Requirements 10 207. ETOPS In-Service Experience Requirements 11 208. Operational Reliability and Systems Suitability Requirements 11

CHAPTER 3. REQUIREMENTS FOR ETOPS AUTHORIZATION 13 300. ETOPS Requirements 13 301. Maintenance Requirements for Two-Engine ETOPS Authorization 13 302. ETOPS Maintenance Training Requirements 23 303. ETOPS Flight Operations Requirements 24 304. Flight Operations Training Requirements 35

CHAPTER 4. APPLICATIONS TO CONDUCT ETOPS 37 400. ETOPS Qualifications 37 401. Application for ETOPS Authorization 38 402. ETOPS Authorities 38 403. ETOPS Authorization Requirements 39 404. Validation Flight(s) 42 405. Required Demonstration on a Validation Flight 43

CHAPTER 5. FAA ETOPS APPROVAL 45 500. Final ETOPS Operating Authority 45 501. ETOPS OpSpecs 45 502. Changes to Approved ETOPS Operations, Maintenance and Training Procedures 45 503. Processes after Receiving ETOPS Authority 45

CHAPTER 6. POLAR OPERATIONS 47 600. Background 47 601.Defintion 47 602. Applicability 47 603. Polar Requirements 47 604. Validation before Approval 50

Page ii

605. FAA Polar Area Approval 50

APPENDIX 1. DEFINITIONS (3 pages) 1 APPENDIX 2. ETOPS APPROVALS (10 pages) 1 APPENDIX 3. ETOPS APPROVAL METHODS (6 pages) 1

Page iii

CHAPTER 1. GENERAL

CHAPTER 1. GENERAL

100. APPLICABILITY. This advisory circular (AC) concerns those certificate holders applying for approval to conduct Extended Operations (ETOPS) under Title 14 of the Code of Federal Regulations (14 CFR) part 121, §121.161, as well as those certificate holders applying for approval to conduct flights where a portion of which traverse either the North or South Polar Areas, as defined in part 121, § 121.7. This AC also provides guidance in resolving operational issues to certificate holders currently conducting such operations.

101. CANCELLATIONS. The following AC's and policy letters are canceled:

• AC 120-42A, Extended Range Operation with Two-Engine Airplanes, dated December 30, 1988

• ETOPS Policy Letter (EPL) 95-1, 138-Minute ETOPS Operational Approval Criteria, dated December 19, 1994

• EPL 20-1, 207-Minute ETOPS Operational Approval Criteria, dated March 21, 2000

• Federal Aviation Administration (FAA) Policy Letter, Guidance for Polar Operations, dated March 5, 2001

102. RELATED REGULATIONS. 14 CFR part 21, § 21.4; part 25, § 25.1535; part 121, §§ 121.7, 121.97, 121.99, 121.106, 121.135, 121.161, 121.162, 121.191, 121.197, 121.374, 121.410, 121.415, 121.565, 121.624, 121.625, 121.631, 121.633, 121.646, 121.687, 121.689, 121.703, 121.704, and 121.705; and part 121, appendix P (http://www.gpoaccess.gov/ecfr).

Par 100 Page 1 (and 2)

CHAPTER 2. BACKGROUND ON ETOPS

CHAPTER 2. BACKGROUND ON ETOPS

200. ETOPS REGULATORY REQUIREMENTS.

a. All two-engine airplanes and three- and four-engine passenger-carrying airplanes operated under part 121 are required to comply with § 121.161. This regulation imposes special requirements for ETOPS for these airplanes. These operations are defined as:

(1) Two-Engine Airplanes. These are flights whose planned routing contains a point farther than 60 minutes flying time from an adequate airport at an approved one-engine inoperative cruise speed under standard conditions in still air.

(2) Passenger-Carrying Airplanes with More Than Two Engines. These are flights whose planned routing contains a point farther than 180 minutes flying time from an adequate airport at an approved one-engine inoperative cruise speed under standard conditions in still air.

b. To conduct ETOPS, the specified airplane-engine combination must be certificated to the airworthiness standards of transport-category airplanes and be approved for ETOPS. Airplane certification guidance for ETOPS can be found in §§ 121.162 and 25.1535. As with all other operations, a certificate holder requesting any route approval must first show that it is able to satisfactorily conduct operations between each required airport as defined for that route or route segment, and any required en route alternate airport. Certificate holders must show that the facilities and services specified in §§ 121.97 through 121.107 (domestic and flag operations) and §§ 121.113 through 121.127 (supplemental and commercial operations) are available and adequate for the proposed operation. In addition, the certificate holder must be approved for ETOPS under part 121. This AC provides the additional guidance for certificate holder approval for ETOPS.

201. EVOLUTION OF ETOPS.

a. Section 121.161 has an extensive historical basis, which began as early as 1936. Before obtaining approval for operation in 1936, an applicant operating an airplane with two piston engines were required to show that intermediate fields available for safe takeoffs and landings were located at least at 100-mile intervals along the proposed route. In 1953, § 121.161 imposed the 60-minute rule on two- and three-engine airplanes. In 1964, three-engine airplanes were exempted, leaving the restrictions only on two-engine airplanes based on the lack of satisfactory engine reliability in the operation. In response to improvements in engine design and reliability, and responding to the needs of industry, the FAA has provided guidance for deviations from the rule that have allowed two-engine operations to expand incrementally beyond the initial 60-minute restriction. Currently, engine reliability has improved to a level where the safety of the operations is not impacted so much by the number of engines, but by other factors that affect operations of all airplanes whose routings take them great distances from adequate airports. Throughout the evolution of the current § 121.161, the following factors have remained constant:

(1) The rule has always applied to all areas of operation, and has not been limited to overwater operations.

(2) Any additional restrictions imposed or, alternatively, any deviations granted to operate in excess of the basic requirements, were based on a finding by the Administrator that adequate safety would be provided in the proposed operation and current levels of safety would be maintained when all factors were considered. This finding was never limited to engine reliability alone.

(3) The airports used in meeting the provisions of the rule must be adequate for the airplane used (that is, available for safe landings and takeoff with the weights authorized).

(4) Adequate levels of safety within the operation are to be maintained. Operations over increasingly remote areas and the possibility of increased diversion lengths have a potentially negative impact on the safety of the diversion, and thus the operation as a whole. Additional regulatory requirements are intended to ensure that this potential increase in risk is mitigated and that adequate levels of safety within operations are retained.

(5) When considering the impact of operating at greater distances from airports, the certificate holder must show that the operation can be conducted at a level of reliability that maintains an acceptable level of risk.

b. In June of 1985, responding to the industry's desire to take advantage of the increased reliability and capabilities of two-engine airplanes, the FAA issued AC 120-42. This AC provided guidance on one means of obtaining deviation authority from § 121.161 to allow two-engine airplanes to operate on routes up to 120 minutes from an adequate airport after demonstration of specific levels of in-service experience and systems reliability. The FAA amended this AC in 1988 (AC 120-42A) to permit two-engine airplanes to operate up to

180 minutes from an adequate airport. These ACs introduced the term "ETOPS" for those specific Extended Operations and addressed airplane and engine design aspects, maintenance programs, and operations. Both of these ACs encompassed the following precepts:

(1) Reliance on a two-step approval that included type design of the airplane-engine combination and approval of the certificate holder's operation.

(2) Risk, as measured by diversion length, is mitigated by application of regulations and guidance reflecting current best practices that address the type certification of the ETOPS airplane and its systems as well as the operational environment of such operations.

(3) ETOPS can be managed successfully, and the level of safety can be maintained, by up-to-date regulations and guidance that articulate quantifiable standards of reliability and experience.

c. The original guidance for extended-range operations with two-engine airplanes in AC 120-42 allowed an increase of up to 15 percent to the maximum diversion time of

120 minutes. This provision was eliminated with the release of the guidance in AC 120-42A, providing for operations up to 180 minutes. Recognizing a need for ETOPS diversion authority between 120 and 180 minutes, the FAA reinstated the 138-minute provision by issuing EPL 95-1 in 1994. In March of 2000, at the request of the industry, the FAA issued ETOPS Policy Letter (EPL) 20-1, 207 Minute ETOPS Operation Approval Criteria. This document provided a similar

15 percent increase in the 180-minute maximum diversion time and gave limited relief to ETOPS certificate holders in the specific case of North Pacific Operations.

d. Since the advent of the original § 121.161, extended two-engine airplane operations have been governed by this rule, and the process of evolving and progressive guidance has reflected the successful and ever-increasing experience of the industry. As capable as this body of guidance has been in the past, it became increasingly clear that a need existed to codify all the disparate documents into a single body of rules, and to update the existing rules to reflect all the industry improvements such progress has used as its basis. Consequently § 121.161 was revised to expand two-engine operational authority under successful ETOPS processes and require certain operations of all passenger-carrying part 121 airplanes to adopt ETOPS requirements. This AC reflects current § 121.161 regulatory requirements.

202. ETOPS APPLICABILITY TO ALL PASSENGER-CARRYING AIRPLANES FLOWN IN LONG-RANGE OPERATIONS.

a. AC 120-42 in 1985, and AC 120-42A in 1988, recognized the increasing reliability of turbojet engines and helped to establish type design and operational practices for safe and reliable long-range operations with two-engine airplanes. As the technology and reliability of two-engine airplanes continued to improve, due in large measure to the requirements of these documents, such operations became compatible with those long-range operations typically associated with three- and four-engine airplanes. At the same time this technology brought two-engine airplanes to the arena of long-range operations, the infrastructure to support such operations was changing. Political and funding priorities forced the closure or reduction in basic services of a number of airports, military and civilian, in remote areas that historically had been used as diversion airports for routes over oceanic and/or desolate land areas. The increasing use of polar flights, while creating economic benefits, has also brought new challenges to the operation. The risks associated with these areas' remoteness, harsh climate and terrain, and their unique operational issues, needed to be addressed to maintain an equivalent level of safety in the operation.

b. These issues began to significantly impact the viability of all long-range two-engine airplane operations under current regulations, and likewise began to erode the basic safety net that long-range operations in three- and four-engine airplanes had relied on. Because of these pressures and the increasing commonality of all long-range operations, the data began to show that ETOPS requirements and processes are generally applicable to all long-range passenger-carrying operations, including those by three- and four-engine airplanes, and would improve the safety and viability of such operations. All long-range passenger-carrying airplanes, regardless of the number of engines, needed a viable diversion airport in the case of onboard fire, medical emergency, or catastrophic decompression. Ensuring availability of en route alternate airports, adequate fire fighting coverage at these airports, and fuel planning to account for depressurization are sound operational practices for all airplanes, including three- and four-engine airplanes. Likewise, planning for the maximum allowable diversion and worst-case scenarios should account for all airplane time-critical systems.

c. Unlike the ETOPS guidance provided for two-engine airplanes, there has been no regulatory framework governing the long-range operations of three- and four-engine airplanes.

For example, in emergencies such as loss of cabin pressure, current regulations require adequate oxygen supplies but do not require the operator to consider the amount of extra fuel necessary to reach a diversion airport.

(1) An analysis of operational data shows that between 1980 and 2000, 33 of the 73 cruise depressurization events on one manufacturer's airplanes occurred on airplanes with more than two engines.

(2) A study conducted by this manufacturer using a modern four-engine aircraft carrying normal route planning fuel reserves raises issues about the adequacy of the current fuel planning requirements in the event of a diversion.

d. Operational data shows that the diversion rate for all airplane-related and non-airplanerelated causes are comparable between two-engine airplanes and airplanes with more than two engines. Consequently, the FAA has found that there is a need for all passenger carrying operations beyond 180 minutes from an adequate airport to adopt many of the ETOPS requirements that have been based on sound safety principles and successfully proven over many years of operations. Accordingly, the FAA revised § 121.161 to include passenger-carrying airplanes with more than two engines in these long-range operations.

203. EXTENDED OPERATIONS.

a. Since 1985, the acronym, ETOPS, has been defined as "extended twin-engine operations" and has been limited to part 121 airplanes with only two engines. Current regulations have extended these applications to all passenger-carrying airplanes operating in both 14 CFR parts 121 and 135, and the acronym has now been redefined to mean "extended operations." This is to acknowledge the similarity of certain long-range passenger-carrying operations of all airplanes operating today, and the common issues that impact such operations.

b. Since 1988, the ETOPS limit for two-engine airplanes has been 180 minutes from an adequate airport at an approved one-engine inoperative cruise speed under standard conditions in still air (excluding the limited authority in the North Pacific given under EPL 20-1, 207-Minute ETOPS Operational Approval Criteria, dated March 21, 2000). Service experience has shown that although limited, this authority has satisfactorily supported the vast majority of the world's current aviation routes.

c. Those areas not supported within 180-minute diversion authority tend to be routes over remote areas of the world that are uniquely challenging to the operation. These areas include the South Polar Region, a small section in the South Pacific, the southern South Atlantic Ocean between South America and Africa, the southern Indian Ocean and the North Polar area under certain winter weather conditions. The additional operational challenges of these routes are equally demanding of all airplanes, regardless of the number of engines, and include such issues as extremes in terrain and meteorology, as well as limited navigation and communications infrastructure. Support of a necessary diversion and subsequent recovery in such areas demands added training, expertise, and dedication from all certificate holders. The development of ETOPS requirements is intended to address all these issues.

d. Even though for continuity with current two-engine ETOPS the existing acronym ETOPS is retained, the ETOPS acronym has been re-defined. ETOPS has been expanded to include all passenger-carrying airplane operations where a proposed flight plan includes any point that is greater than 180 minutes from an adequate airport (at an approved one-engine inoperative cruise speed under standard conditions in still air).

204. PRECLUDE AND PROTECT.

a. The whole premise of ETOPS has been to preclude a diversion and, if it were to occur, to have programs in place to protect the diversion. Under this concept, propulsion systems are designed and tested to ensure an acceptable level of in-flight shutdowns (IFSD), and other airplane systems are designed and tested to ensure their reliability. Two-engine airplane maintenance practices are enhanced to better maintain and monitor the condition of the engines and systems significant to ETOPS. The design of these enhanced practices has been a major factor in the joint development of the FAA's and industry's aggressive steps to develop a foundation to resolve problems with airplane systems and engines in order to minimize the potential for procedural and human errors, thereby precluding a diversion.

b. However, despite the best design, testing, and maintenance practices, situations occur that may require an airplane to divert. Regardless of whether the diversion is for technical (airplane system- or engine-related) or non-technical reasons, the certificate holder must have a flight operations plan to protect that diversion. For example, such a plan must include ensuring that pilots are knowledgeable about diversion airport alternates and weather conditions (§ 121.631), have the ability to communicate with the certificate holder's dispatch office and air traffic control (ATC) (§§ 121.99 and 121.122), and have sufficient fuel to divert to the alternate (§ 121.646). Under the "preclude and protect" concept, various failure scenarios need to be considered. For example, during the design of the airplane, time-limited systems such as cargo compartment fire suppression/containment capability are considered. Fuel planning must account for the possibility of decompression or the failure of an engine with considerations for in-flight icing conditions. Best options under these scenarios should be provided to the pilot before and during the flight.

c. This philosophy has been critical to the success of two-engine ETOPS in the past and has been applied to these airplanes in operations beyond 60 minutes from an adequate airport. This application is based on the requirements of§ 121.161 and the engine inoperative diversion requirements of § 121.565. In-service data shows that all airplanes, regardless of the number of engines, divert from time to time for various causes. All passenger-carrying operations conducted where there are a limited number of en route airports, where the support infrastructure is marginal, or where there are challenging weather conditions should adopt many of the same elements of the same preclude and protect concept. If certificate holders plan to operate passenger-carrying airplanes with more than two engines in areas where en route airports are farther away than 180 minutes, these operations are also required to meet certain standards defined under ETOPS to ensure that all efforts are made to preclude a diversion, and if a diversion does occur, that procedures are in place to protect that diversion.

205. ETOPS AREAS OF OPERATION.

a. ETOPS areas of operation are defined by § 121.7 to be areas beyond a certain distance from adequate airports measured by an airplanes one-engine inoperative cruise speed under standard conditions in still air. Because of the impact such distances might have on the diversion time of an airplane, regulatory guidance has been established for the planning, operational, and equipage requirements for such operations. A certificate holder must apply to the FAA for approval to operate in an ETOPS area using the methodologies in this AC or other means approved by the FAA. When approval is granted, the ETOPS authority for a specific ETOPS area of operations will be noted in the certificate holder's operations specifications (OpSpecs).

b. Most ETOPS authorities for two-engine ETOPS beyond 180 minutes are limited to a specific geographical region. Historically, ETOPS authorities for two-engine airplanes up to 180 minutes were developed based on a specific need in a particular operating area. Limiting expanded ETOPS authority beyond 180 minutes (for two-engine airplanes) serves several purposes.

(1) The primary importance is the preclusion of an arbitrary use of diversion authority beyond that necessary to complete the operation safely and efficiently. Because it is accepted that increased diversion times potentially increase the risk of the operation a certificate holder must make every effort to plan ETOPS with a maximum diversion distance of 180 minutes or less, if possible.

(2) It should be a goal of all two-engine airplane flight planning to operate to the shortest diversion time that provides the widest range of options in the event of a diversion while recognizing the economic benefits of a more direct route and the safety benefits of diverting to an airport that is well equipped. Tying increased diversion authority to specific areas of operation accomplishes this goal while sufficiently addressing the operational needs of the industry.

(3) Likewise, this focus on specific needs and areas of operation does not add impetus to any perceived rationale for further degradation in the availability or capabilities of en route alternates in remote areas of the world. Although the industry has no direct authority to affect the actions of sovereign nations, it is reasonable to base operations on the value of en route alternate availability at reasonable diversion distances.

(4) In consideration of the successful history of three- and four-engine airplane operations and the reliability and redundancy of current engines used in this operation, ETOPS for these airplanes does not have similar restrictions and ETOPS authorities are not limited to geographic areas. However, like twin-engine operators, the three- and four-engine operator is required to designate the nearest available ETOPS alternate along the planned route of flight and must remain within a 240 minute diversion time if possible.

c. In its application for ETOPS authority, the certificate holder will typically request a specific ETOPS area of operation based on an analysis of proposed routings and the availability of airports sufficient to support the operational requirements of the ETOPS regulations. Because the operating rules distinguish between ETOPS up to 180 minutes, and ETOPS beyond 180

minutes, the requested level of ETOPS authority in a certificate holder's application will necessarily have to be assessed differently for ETOPS beyond 180 minutes.

(1) Two-Engine Airplanes up to 180-Minute ETOPS and 207-Minute ETOPS Authority in the North Pacific Area of Operations. The ETOPS area of operation is the area bounded by distance circles representing the approved one-engine inoperative cruise speed under standard conditions in still air chosen by the applicant. The actual flight plan must comply with the fuel supply requirements in § 121.646(b) and must therefore account for wind. However, the flight planning limitations of § 121.633(a) for airplane systems do not require the operator to account for wind in such calculations for flight planning and for determining the ETOPS area of operations in these cases. This allows the applicant to choose an operating authority in his or her application that is based on the "ETOPS area of operation" determination. In other words, the distance from alternates in a certificate holder's route planning exercise will be the same value used to determine the type design criteria for the airplane-engine combination used in the operation, and the ETOPS approval necessary to fly the route under all flight planning conditions.

(2) ETOPS Beyond 180 Minutes (Two-Engine Airplanes and All Passenger- Carrying Airplanes With More Than 2 Engines). As required by § 121.633(b), for ETOPS beyond 180 minutes for all airplanes, the ETOPS operation must account for the effects of wind and temperature on the calculated distances. Consequently the planning for an ETOPS flight beyond 180 minutes is more complex.

(a) The certificate holder should first conduct a route planning exercise for each planned city pairing to determine the diversion authority needed in still air conditions. If the route or segments of the route exceed 180 minutes based on one engine inoperative speed and still air, then a secondary planning exercise (that may be required seasonally) should be conducted that factors in expected winds and temperatures on that route. The distance between adequate alternate airports on the route is converted into time (minutes) computed for all engine cruise speed, as well as engine inoperative speed. The number of minutes cannot exceed the time-limited system certified capability (cargo fire suppression and the other most limiting system)that is identified in the Configuration Maintenance Procedures (CMP) or Aircraft Flight Manual (AFM) (or any other FAA-approved manufacturer's document) less the 15-minute pad. The operator needs to determine how much system capability is required for the planned route and equip its airplane to have sufficient margins. Finally, for the actual flight, the operator's flight planning must be within the airplane systems capability for the selected ETOPS alternate airports on the planned route based on diversion times that are calculated using known or forecast winds and temperature conditions.

(b) As a minimum, the certificate holder must ensure that the time-limited systems requirements of § 121.633(b) are met at the equal-time points between ETOPS alternates determined by the most limiting en route fuel supply requirements of § 121.646(b), commonly referred to as the ETOPS critical fuel scenario. Certificate holders flying three- and four engine airplanes, prior to the established installation time and certification time requirements of the regulation for these systems and their airplanes, are exempt from these flight planning limitations.

(c) Once the required fire suppression systems are installed (no later than Februaryl5, 2013 for turbine powered airplanes with more than two engines) the certificate holder must follow the flight planning limitations of § 121.633(b)(1). As required by

§ 121.162(d), for airplanes with more than 2 engines manufactured on or after February 17, 2015, the CMP document for that model will list the airplane's most limiting ETOPS Significant System time issued in accordance with § 25.3(c). The Certificate holder operating an airplaneengine combination with more than two engines is required to comply with § 121.633(b)(2) if the CMP lists the most limiting ETOPS Significant System time.

d. Credit for the Driftdown. For the purposes of computing distances for ETOPS Area of Operation, credit for driftdown may be taken.

e. Actual Diversion Time. Actual diversion time may exceed the authorized diversion time as long as the flight is conducted within the authorized ETOPS Area of Operation, and complies with the requirements of § 121.633.

206. ETOPS ALTERNATE REQUIREMENTS.

a. One of the distinguishing features of ETOPS operations is the concept of an en route alternate airport being available where an airplane can divert following a single failure or a combination of failures that require a diversion. Most airplanes operate in an environment where there usually is a choice of diversion airports available within a close proximity to the route of flight. However, a certificate holder conducting ETOPS may only have one alternate airport within a range dictated by the endurance of a particular airframe system (for example, the cargo fire suppressant system), and that system or system failure may dictate the approved maximum diversion time for that route. Therefore, it is important that any airport designated as an ETOPS alternate have the capabilities, services, and facilities to safely support the operation. The weather conditions at the time of arrival should provide assurance that adequate visual references will be available upon arrival at decision height (DH) or minimum descent altitude (MDA), and that the surface wind conditions and corresponding runway surface conditions will be acceptable to permit the approach and landing to be safely completed with an engine and/or systems inoperative.

b. At dispatch, an en route alternate must meet ETOPS alternate weather requirements in § 121.625 and as specified in Chapter 3, paragraph 303c(5) of this AC and in the certificate holder's OpSpecs. Because of the natural variability of weather conditions with time, as well as the need to determine the suitability of a particular en route alternate before departure, such requirements are higher than the weather minimums required to initiate an instrument approach. This is necessary prior to the time that the instrument approach would be conducted, to provide for some deterioration in weather conditions after planning. This increases the probability that the flight will land safely after a diversion to an alternate airport. The airport of departure (takeoff) and the destination airport (unless used concurrently as an ETOPS alternate) are not required to meet the weather minima for ETOPS alternates, as these airports are subject to other regulations (e.g., §§ 121.617, 121.621, and 121.623).

c. While en route, the forecast weather for designated ETOPS alternates should remain at or above operating minima. This provides ETOPS flights with the ability to resolve all diversion

decisions successfully throughout the flight. The suitability of an en route alternate airport for an airplane that encounters an in-flight situation that necessitates a diversion during ETOPS operations is based on a determination that the airport still is suitable for the circumstances, and the weather and field conditions at that airport permit an instrument approach to be initiated and a landing completed.

207. ETOPS IN-SERVICE EXPERIENCE REQUIREMENTS.

a. When AC 120-42 was first released in 1985, two-engine ETOPS was a new concept and ETOPS approvals were sought on airframe-engine combinations that were already in service. Hence, it was logical to establish criteria for approvals based on in-service experience. At that same time, the FAA recognized the possibility that other approval methods could be developed without in-service experience, and accordingly, provided statements that recognized those options. The original two-engine ETOPS requirements for engine reliability were based on a world fleet in-service experience of 250,000 hours. For 120-minute ETOPS, the FAA additionally required the certificate holder to have 12-consecutive months of operational in-service experience with the airplane-engine combination (AEC). For 180-minute ETOPS, the FAA required the certificate holder to have previously gained 12 consecutive months of operational in-service experience with the specified AEC conducting 120-minute ETOPS. These basic, two-engine in-service requirements have been retained and are discussed in Appendix 3. Achieving these levels of experience, combined with the required levels of engine reliability, is an acceptable means of attaining ETOPS approval for operators of two-engine airplanes.

b. At the time AC 120-42A was drafted, the FAA recognized that a reduction of two-engine in-service experience requirements or substitution of in-service experience on another airplane would be possible. Any reduction was to be based on an evaluation of the certificate holder's ability and competence to achieve the necessary reliability for the particular AEC in ETOPS. For example, a reduction in in-service experience would be considered for a certificate holder who could show extensive in-service experience with a related engine on another airplane that had achieved acceptable reliability. The FAA also allowed certificate holders unable to initially fly ETOPS routes at the lesser thresholds to make use of ETOPS simulation or demonstration programs in their application for 180-minute ETOPS. Eventually specific guidance material (AC 120-42A, appendix 7, Accelerated ETOPS Operational Approval) was developed by the FAA permitting ETOPS without accumulating in-service experience in the airplane-engine combination. Most subsequent ETOPS approvals have been granted under these guidelines and this method is retained in Appendix 3.

208. OPERATIONAL RELIABILITY AND SYSTEMS SUITABILITY REQUIREMENTS.

a. The safety of long-range operations such as ETOPS depends on the reliability of all airplane systems including the propulsion systems. Time-limited systems such as cargo compartment fire suppression/containment capability must be considered (§ 121.633). The certificate holder must also have an established program that monitors the reliability of systems significant to ETOPS (§ 121.374).

b. In order to achieve and maintain the required engine reliability standards, the certificate holder operating a two-engine airplane in ETOPS should assess the proposed maintenance and reliability program's ability to maintain a satisfactory level of airplane systems reliability for the particular airplane-engine combination. All certificate holders should design the flight operations and, if applicable, the maintenance programs for ETOPS with an objective to preclude diversions and, if a diversion does occur, to protect that diversion. Required ETOPS maintenance practices also must minimize the potential for procedural and human errors that could be detrimental to the safety of the operation. Fuel planning must account for the possibility of a depressurization and/or failure of an engine with considerations for in-flight icing conditions (§ 121.646).

c. The type design requirements for ETOPS certification consider the probability of occurrence of conditions that would reduce the capability of the airplane or the ability of the flight crewmember to cope with an adverse operating condition. System failures or malfunctions occurring during extended range operations could affect flight crewmember workload and procedures. Although the demands on the flight crewmember may increase, a manufacturer applying for ETOPS type design approval must consider crew workload, operational implications, and the crew's and passengers' physiological needs during continued operation with failure effects for the longest diversion time for which it seeks approval. The manufacturer must also conduct flight tests to validate the adequacy of the airplane's flying qualities and performance, and the flightcrew's ability to safely conduct an ETOPS diversion with expected system failures and malfunctions. An ETOPS operator should carefully consider the possible adverse effects that changes in airplane equipment or operating procedures may have on the original evaluations conducted when the airplane was approved for ETOPS before implementing such changes.

d. Following a determination that the airframe systems and propulsion systems are ETOPS type design approved as per part 25, an in-depth review of the applicant's required ETOPS programs will be accomplished to show the ability to achieve and maintain an acceptable level of systems reliability, and to safely conduct these operations.

CHAPTER 3. REQUIREMENTS FOR ETOPS AUTHORIZATION

CHAPTER 3. REQUIREMENTS FOR ETOPS AUTHORIZATION

300. ETOPS REQUIREMENTS. The FAA may approve ETOPS for various areas of operation in accordance with the requirements and limitations specified in part 121, appendix P. ETOPS must be authorized in the certificate holder's OpSpecs and conducted in compliance with those sections of part 121 applicable to ETOPS.

a. As of February 15, 2008, certificate holders operating passenger-carrying airplanes with more than two engines, having the authority to operate on specific ETOPS routes should not need to re-apply for their specific route authority. However, the certificate holder is required to comply with all the applicable ETOPS flight operational regulations described in this AC, and must have their ETOPS programs and processes approved by their certificate-holding district office (CHDO) with the concurrence of the Director, Flight Standards Service.

b. The certificate holder's ETOPS requirements must be specified in their maintenance and operations programs. Maintenance requirements necessary to support ETOPS are explained in paragraphs 301 and 302. Flight operations requirements necessary to support ETOPS are described in paragraphs 303 and 304.

c. The requirements for the various levels of ETOPS authorities are listed in tabular form in Appendix 2.

301. MAINTENANCE REQUIREMENTS FOR TWO-ENGINE ETOPS AUTHORIZATION. The certificate holder conducting ETOPS with two-engine airplanes must comply with the ETOPS maintenance requirements as specified in § 121.374. These requirements are discussed in paragraphs a through o as follows:

a. Continuous Airworthiness Maintenance Program (CAMP). The basic maintenance program for the airplane being considered for ETOPS is a CAMP that may currently be approved for a non-ETOPS certificate holder for a particular make and model airplane-engine combination. The basic CAMP must be a maintenance and inspection program that contains the instructions for continued airworthiness (ICA) based on the manufacturer's maintenance program, or those contained in a certificate holder's maintenance manual approved in its OpSpecs. The certificate holder and its CHDO must review the CAMP to ensure it provides an adequate basis for development of a ETOPS maintenance program. The certificate holder's ETOPS CAMP must include specific ETOPS requirements, which will be incorporated as supplemental requirements to the basic CAMP. These supplemental requirements include the enhanced maintenance and training processes that will ensure ETOPS airplanes achieve and maintain the level of performance and reliability necessary for ETOPS operations. These supplemental requirements, referred to in the industry as ETOPS processes or ETOPS process elements, currently should be in place for existing ETOPS operations. Prospective ETOPS certificate holders must supplement their basic CAMP with those program elements defined in paragraphs b through o below.

b. ETOPS Maintenance Document. The certificate holder must develop a document for use by personnel involved in ETOPS. This may be a separate document or a part of other maintenance documents. It need not be inclusive but should, at least, reference the maintenance

program and other pertinent requirements clearly indicating where all facets of the ETOPS maintenance program are located in the certificate holder's document system. All ETOPS requirements, including supportive programs, procedures, duties, and responsibilities, must be identified. The ETOPS document(s) must reflect the actual policies and procedures the certificate holder expects their ETOPS maintenance personnel to adhere to. The document(s) should be user friendly, and be accessible to all affected personnel. The initial document must be submitted to the CHDO and be approved before being adopted.

c. ETOPS PRE-DEPARTURE SERVICE CHECK (PDSC).

(1) The certificate holder must develop an ETOPS PDSC to verify that the airplane and certain significant items are airworthy and ETOPS capable. Each certificate holder's PDSC may vary in form and content. The prerequisites for an acceptable PDSC are content and suitability for the specific certificate holder's needs.

(2) All certificate holders must address ETOPS significant system airworthiness in their ETOPS maintenance program, including the PDSC. Specifically, the PDSC is a maintenance task that should include an applicable maintenance records review and an interior and exterior inspection. The PDSC is sometimes referred to as an expanded transit check inspection. The PDSC should include visual inspections and procedures applicable to determining ETOPS Significant Systems airworthiness status. The airworthiness status determination should include a process for determining engine and auxiliary power unit (APU) oil quantities, and consumption rates prior to ETOPS dispatch.

NOTE: Proper servicing of fluids, such as engine, APU, generator systems, and hydraulic systems is a vital ingredient to successful ETOPS operations. Some current ETOPS operators have had incidents resulting from improper fluid servicing, or not properly determining or addressing high consumption rates. This has resulted in IFSDs and diversions. Certificate holders should consider this area very seriously when developing their maintenance checks, including the PDSC.

(3) Some certificate holders may elect to include tasks in the PDSC that are driven by their reliability programs and are not related to ETOPS significant systems. However, the certificate holder must clearly identify the ETOPS related tasks on their PDSC if non-ETOPS qualified maintenance personnel are to accomplish the non-ETOPS tasks. An appropriately trained maintenance person, who is ETOPS qualified, and authorized by the certificate holder, must accomplish and certify by signature the completion of ETOPS specific tasks. An appropriately trained person who is ETOPS qualified and authorized by the certificate holder must certify by signature, that the ETOPS pre-departure service check has been completed. Appropriately trained persons are those that have satisfactorily completed the certificate holder's ETOPS training program. The signatory person that certifies the completion of the PDSC must also meet the following criteria:

(a) Inside the United States, the signatory person holds a U.S. mechanic's certificate with airframe and powerplant ratings, and works for an operator authorized to engage in part 121 operation, or works for a part 145 repair station.

(b) Outside the United States, the signatory person holds a U.S. mechanics certificate with airframe and powerplant ratings, or holds a certificate in accordance with § 43.17(c)(1) or,

(c) Works for an ETOPS maintenance entity and has the requisite experience or specific training needed to accomplish the task and is authorized to complete the PDSC and return the aircraft to service on behalf of the ETOPS maintenance entity; the signatory person does not have to hold a U.S. or Canadian certificate.

NOTE: An ETOPS maintenance entity is an entity that has been authorized to perform ETOPS maintenance and authorized by the certificate holder to complete ETOPS pre-departure service checks. That entity is certificated to engage in part 121 operations; a repair station certificated under part 145, or an entity authorized pursuant to § 43.17(c)(2).

(4) The PDSC must be certified complete immediately before each scheduled ETOPS flight. The term "immediately" has historically meant to be no more than 2 to 4 hours before the flight. However, the FAA may grant some relief from this time period under certain conditions. The certificate holder should explain any rational for such deviations in its ETOPS maintenance document, which is approved by its CHDO.

(5) A PDSC may not be required before all ETOPS flights. The FAA may grant relief following irregular operations because of non-mechanical issues, such as weather or medical emergency diversions, or when operating ETOPS into specific areas of operation. For example, if an airplane scheduled for an ETOPS flight receives a PDSC before departure and subsequently must divert or turn back for reasons other than mechanical, the certificate holder must identify in its ETOPS maintenance document what procedures its flight operations and maintenance personnel would follow to preclude performing another PDSC. If a mechanical discrepancy develops as a result of the diversion or turn back, the certificate holder may have to perform another PDSC. For example, when an overweight landing inspection reveals an ETOPS Significant System discrepancy that requires maintenance intervention, another PDSC is required.

(6) In areas where prevailing weather conditions are stable and generally do not approach extremes in temperature, wind, ceiling, and visibility, such as in the Caribbean/Western Atlantic (75-minute ETOPS) and Micronesia routes (90-minute ETOPS), the service check may not be required for the return leg of an ETOPS flight. This check is not precluded by any other maintenance check.

d. Dual Maintenance.

(1) ETOPS dual maintenance, otherwise referred to as identical maintenance, multiple maintenance, and simultaneous maintenance, requires special consideration by the certificate holder. This is to recognize and preclude common cause human failure modes. Proper verification processes or operational tests, prior to ETOPS, are required when dual maintenance on significant systems occurs.

(2) Dual maintenance on the "same" ETOPS Significant System can be described as actions performed on the same element of identical, but separate ETOPS Significant Systems during the same routine or non-routine visit. Examples of maintenance on the "same" ETOPS Significant System are: maintenance on both air cycle machines (or equivalent) in the air conditioning systems during a turnaround flight; removal of either both engine oil filters, or both chip detectors; and replacement of both chip detectors.

(3) Dual maintenance on "substantially similar" ETOPS Significant Systems specifically addresses maintenance actions on engine-driven components on both engines. An example of dual maintenance on "substantially similar" ETOPS Significant Systems could include: replacement of the No. 1 Integrated Drive Generator (IDG) and the No. 2 Engine Driven Pump (EDP).

(4) The certificate holder must establish procedures that minimize identical maintenance actions from being scheduled or applied to multiple similar elements in any ETOPS Significant System during the same routine or non-routine maintenance visit. In order to manage this requirement the certificate holder must develop a list of fleet-specific ETOPS Significant

Systems and include them in their ETOPS maintenance document(s).

(5) The FAA recognizes that sometimes ETOPS dual maintenance actions cannot be avoided or precluded because of unforeseen circumstances that occur during ETOPS operations. In the line maintenance arena, one example would be when an ETOPS airplane has inbound discrepancies on both engines' oil systems, or there is a generator replacement on one engine, and an oil system discrepancy on the other engine. Additionally, staggering maintenance on ETOPS Significant Systems in the heavy maintenance arena is not always possible or feasible. However, to minimize human factor common cause risk, the certificate holder should attempt to minimize dual maintenance on ETOPS Significant Systems wherever/whenever possible.

(6) In any event, when dual maintenance is performed on a ETOPS Significant System, the certificate holder must have written procedures in its ETOPS maintenance document that addresses this situation. At a minimum, the certificate holder must ensure:

(a) Separate ETOPS-qualified maintenance persons perform the tasks,

(b) The maintenance action on each of the elements in the ETOPS Significant System is performed by the same technician under the direct supervision of a second ETOPS qualified individual, and

(c) It verifies the effectiveness of the corrective actions to those ETOPS Significant Systems before the airplane enters the ETOPS area of operation. This verification action must be performed using ground verification methods, and in some instances, in-flight verification methods described in the next section of this AC. On an exception basis, the same ETOPS-qualified technician, under the supervision of an ETOPS qualified Centralized Maintenance Control person, may perform the dual maintenance and the ground verification methods only if in-flight verification action is performed.

(7) The FAA acknowledges that the servicing of fluids and gases is not considered maintenance; however, these tasks, when done improperly have adversely affected ETOPS operations. The certificate holder should recognize the hazard associated with improper servicing and do all possible to mitigate the associated risk. Specifically, servicing tasks such as engine, APU, and generator system oil servicing are tasks that require high levels of attention. The FAA encourages the certificate holder to ensure that its programs have separate individuals perform such servicing. However, the FAA recognizes that many certificate holder's route and organizational structures may not lend themselves to these procedures. The certificate holder's program should include detailed servicing instructions, or make readily available servicing instructions. Additionally, the certificate holders should consider including oil servicing in their ETOPS OJT program, regardless of whether one individual or multiple individuals perform the tasks.

e. Verification Program.

(1) The certificate holder must develop a verification program for resolution of airplane discrepancies (corrective actions) on ETOPS significant systems. This program must include corrective action confirmation in specific areas such as engine shutdown, significant system failure, adverse trends, or any prescribed event that could effect an ETOPS operation. The program must ensure corrective action is taken and confirmed successful before the airplane enters an ETOPS area of operation. The certificate holder must verify the effectiveness of the corrective actions following the maintenance action and prior to an ETOPS flight or prior to passing the ETOPS entry point. The ground verification method is accomplished by following the ICA contained in the Airplane Maintenance Manuals (AMM) or the certificate holder's maintenance manuals. These ICAs include built-in test equipment (BITE) and functional/operational checks that often include leak checks after ground runs.

(2) Normally ground verification is acceptable to ensure corrective action. Under certain conditions ground verification beyond that recommended in the ICA or in-flight verification may be required. An example of a condition that would require an in-flight verification is the replacement of an APU component that could affect the APU's ability to start at the ETOPS cruise altitude after cold soak. In-flight verification may be conducted on revenue flights, provided the action is completed before the ETOPS entry point. In those cases where the verification flight will reach the ETOPS entry point approximately 60 minutes into the flight, e.g., departing from an island, and the inflight verification is for APU inflight starting which requires a two-hour cold soak, (see paragraph 301m., "APU In-Flight Start Program"), the operator can initiate the flight with the APU running and shut it down two hours prior to top of descent and initiate the inflight APU start before top of descent. Ground maintenance personnel should coordinate with flight operations personnel whenever an in-flight verification is required. Each certificate holder must identify its ETOPS significant systems, ground verification requirements, and in-flight verification requirements in its ETOPS maintenance document.

(3) The certificate holder must establish a means to ensure any required verification action is accomplished. The certificate holder must include a clear description of who initiates verification actions and who is responsible for completing the actions in its ETOPS maintenance document.

f. Task Identification. The certificate holder must identify all tasks that must be accomplished or certified as complete by ETOPS-qualified maintenance personnel. The intent is to have ETOPS-trained maintenance personnel accomplish these tasks because they are related to ETOPS. ETOPS specific tasks must be:

(1) The certificate holder must identify all tasks that must be accomplished or certified as complete by ETOPS qualified personnel. The intent is to have ETOPS trained maintenance personnel accomplish these identified tasks because they are related to ETOPS. ETOPS specific tasks should be:

(a) Identified on the certificate holder's work forms and related instructions, or

(b) Parceled together and identified as an ETOPS package.

(2) If a certificate holder does not identify ETOPS-related task in their current maintenance program, then all tasks must be accomplished by ETOPS-qualified personnel.

g. Centralized Maintenance Control Procedures. An ETOPS certificate holder, regardless of the size of its ETOPS fleet, must have a centralized entity responsible for oversight of the ETOPS maintenance operation. The certificate holder must develop and clearly define in its ETOPS maintenance document specific procedures, duties, and responsibilities for involvement of their centralized maintenance control personnel in the ETOPS operation. These established procedures and centralized control processes would preclude an airplane from being dispatched for ETOPS flights after an engine IFSD, ETOPS significant system failure, or discovery of significant adverse trends in system performance without appropriate corrective action having been taken.

h. ETOPS Parts Control. The certificate holder must develop a parts control program to ensure the proper parts and configurations are maintained for ETOPS. The program must include procedures to verify that the parts installed on ETOPS airplanes during parts borrowing or pooling arrangements, as well as those parts used after repair or overhaul, maintain the required ETOPS configuration.

i. Reliability Program.

(1) The certificate holder must develop an ETOPS reliability program or enhance its existing reliability program to incorporate the ETOPS supplemental requirements. This program must be designed with early identification and prevention of ETOPS-related problems as the primary goal. The program must be event-oriented, and incorporate reporting procedures for significant events detrimental to ETOPS flights. For those certificate holders that do not have an FAA-approved reliability program, their Continuing Analysis and Surveillance System (CASS) must be enhanced to achieve ETOPS reliability goals. The certificate holder should submit regular ETOPS reliability reports to its CHDO. The frequency of such reporting should be agreed upon between the certificate holder and the CHDO. Customarily, monthly reports have been deemed an acceptable frequency.

(2) In addition to the reporting requirements in § 121.703, the certificate holder must report the following items on their ETOPS airplanes (regardless of ETOPS or Non-ETOPS operation) within 96 hours to its CHDO:

(a) IFSDs, except planned IFSDs performed for flight training.

(b) Diversions and turnbacks for failures, malfunctions, or defects associated with any ETOPS Significant Systems.

(c) Uncommanded power or thrust changes or surges.

(d) Inability to control the engine or obtain desired power or thrust.

(e) Inadvertent fuel loss or unavailability, or uncorrectable fuel imbalance in flight.

(f) Failures, malfunctions or defects associated with ETOPS Significant Systems.

(g) Any event that would jeopardize the safe flight and landing of the airplane on an ETOPS flight.

(3) The reporting of any of the above items must include the information specified in

§ 121.703(e).

(4) The certificate holder must conduct an investigation into the cause of the occurrence of any event listed in § 121.703 and § 121.374(h)(1) and submit its findings to its CHDO.

NOTE: The FAA encourages operator investigations include manufacturers when feasible. If the CHDO determines additional corrective action is necessary, the certificate holder must further investigate and implement appropriate corrective action acceptable to the CHDO.

j . Propulsion System Monitoring.

(1) The certificate holder must monitor its fleet average IFSD rate for the specified airplane-engine combination. It should establish firm criteria regarding the actions it will take when it detects adverse trends in propulsion system conditions. If the IFSD rate, computed on a

12-month rolling average, exceeds the values in the following table, the certificate holder, in conjunction with its CHDO, must investigate common cause effects or systemic errors and submit the findings to its CHDO within 30 days.

NOTE: It may be applicable to combine some similar airplane-engine combinations, due to the commonality of engine type, e.g., 777-200LR and ­ 300ER with GE90-110/115B engine, where the engine build is the same and operations are similar.

In Flight Shut Down Rates Number of Engines Engine Hours ETOPS ETOPS Authorization

2 .05/1000 Up to and including 120 minutes. 2 .03/1000 Beyond 120 minutes up to and including 180 minutes and 207 minutes in North Pacific. 2 .02/1000 Greater than 180 minutes (Except for 207 minutes in North Pacific.

(2) With respect to maintenance, the purpose of monitoring IFSD rates is to provide FAA and operators with a tool for measuring the health of a fleet of ETOPS-approved airplanes in service. Causes of IFSDs or other engine and propulsion system problems may be associated with type design problems and/or maintenance and operational procedures applied to the airplane. It is very important that the certificate holder identify the root cause of events so that an indication of corrective action is available, such as a fundamental design problem that requires an effective hardware (or software) final fix. Repetitive inspections may be satisfactory as interim solutions, but longer-term design solutions, such as terminating actions, may be required if possible. Design problems can affect the whole fleet. The FAA will not revoke an existing ETOPS operational approval solely because of a high IFSD rate. A certificate holder who experiences a type design related event need not be operationally penalized for a problem that is design-related and may not be of their own making. However, maintenance or operational problems may be wholly, or partially, the responsibility of the certificate holder. If a certificate holder has an unacceptable IFSD rate risk attributed to common cause or a systemic problem in operational practices or the maintenance program, then action carefully tailored to that certificate holder may be required, and may include a reduction of the certificate holder's diversion limit.

(3) The certificate holder must investigate an IFSD rate higher than the 12-month rolling average standard that occurs for a mature fleet after the commencement of ETOPS (Refer to the IFSD Rates table above). The certificate holder must investigate any indication of a high IFSD rate; however, it should consider that in the case of the smaller fleet, the high IFSD rate may be because of the limited number of engine operating hours used as the denominator for the rate calculation. This can cause an IFSD jump well above the standard rate because of a single IFSD event. The underlying causes for such a jump in the rate will have to be considered by the Administrator's representative. On occasion, a particular event may also warrant implementation of corrective action even though the overall IFSD rate is not being exceeded.

(4) The 30-day reporting criteria of paragraph 301j(l) is intended to ensure that the certificate holder provides the FAA timely notification of the status of an event investigation. The certificate holder may or may not have root cause or terminating action at the end of the 30-day period, and further discussions with the FAA may be required after this period.

(5) The certificate holder may designate a sub-fleet engine/airframe combination for the purposes of the IFSD monitoring/rate program. The operator may include the IFSD statistics of all engines that are ETOPS configured and are maintained in accordance with the operators ETOPS program even if used on non-ETOPS airplanes.

k. Engine Condition Monitoring. The certificate holder must develop a program for its ETOPS engines that describes the parameters to be monitored, method of data collection, and corrective action processes. The program should reflect the manufacturer's instructions and industry practices, or the certificate holder should establish a program that demonstrates an equivalent level of monitoring and data analysis. The goal of this monitoring program is to detect deterioration at an early stage, and to allow for corrective action before safe operation is affected. In order to achieve this goal, engine data analysis should be accomplished as often as practical. The recommended maximum interval is five days. Engine limit margins must be maintained so that prolonged engine inoperative diversions may be conducted without exceeding approved engine limits (for example, rotor speeds and exhaust gas temperature) at all approved power levels and expected environmental conditions. Engine margins preserved through this program should account for the effects of additional engine loading demands (for example anti-ice and electrical), which may be required during IFSD flight phase associated with the diversion. If oil analysis monitoring, such as the Spectrographic Oil Analysis Program (SOAP), is meaningful and recommended by the manufacturer, the certificate holder should include it in their program.

1. Oil Consumption Monitoring. The certificate holder must develop an engine oil consumption monitoring program to ascertain that there is enough oil to complete the scheduled ETOPS flight. The certificate holder's consumption limit must not exceed the manufacturer's recommendations, and it must trend oil consumption. The certificate holder's oil consumption trending program should be capable of recognizing a spike in the oil consumption rate. A certificate holder who operates an ETOPS aircraft in ETOPS and non-ETOPS operations may elect to develop a program that documents the indicated flight deck oil quantity at each Non- ETOPS station to supplement their oil consumption trend monitoring programs capability to discover an oil spike.

For example, if an ETOPS airplane oil is serviced infrequently, and the quantities aren't regularly recorded, it would be difficult to determine whether the oil added during an ETOPS pre-departure check was the result of normal oil consumption over several flight hours, or a sudden increase which would merit investigation and corrective action prior to the ETOPS flight. The certificate holders trending program may be done manually or by electronic means. The program must consider the amount of oil added at the departing ETOPS station with reference to the running average consumption, as well as monitor for sudden increases in consumption. The monitoring must be continuous including non-ETOPS flights and the oil added at the ETOPS departure station. For example, after servicing, the oil consumption may be determined by maintenance personnel as part of the pre-departure check. The amount of oil added also could be reported to a centralized maintenance control for calculation before the ETOPS flight.

If the APU is required for ETOPS, it must be included in the oil consumption monitoring program. Any corrective actions taken regarding oil consumption must be verified before ETOPS departure.

m. APU In-Flight Start Program.

(1) If the airplane type certificate requires an APU but does not normally require the APU to operate during the ETOPS portion of the flight, the certificate holder must develop an in-flight start and run reliability program to ensure that the APU will continue to provide the performance and reliability established by the manufacturer. Specifically, the program is intended to verify the start and run capability. It is not required to actually load the APU in flight with the generator and/or pneumatics. This monitoring program must include periodic sampling

of each airplane's APU in-flight starting capabilities. Specifically, the certificate holder must ensure that each airplane's APU periodically is sampled rather than repeatedly sampling the same APUs. The certificate holder may adjust sampling intervals according to system performance and fleet maturity. The certificate holder and its CHDO should periodically review the certificate holder's APU in-flight start program data to ensure that the in-flight start reliability is maintained. Should the rolling 12-month APU in-flight start rate drop below 95 percent, the certificate holder should initiate an investigation into any common cause effects or systemic errors in procedures.

(2) The certificate holder should include the criteria below in their APU in-flight start program. The certificate holder should make APU in-flight starts subject to the following conditions:

(a) In-flight APU starts do not need to be performed on ETOPS flights; however, the APU must be in the ETOPS configuration in accordance with the appropriate CMP document, if applicable, for credit to be allowed.

(b) If in-flight APU start is performed on an ETOPS flight, the start may be attempted on the return leg.

(c) The start attempt should be initiated before top of descent, or at such time that will ensure a 2-hour cold soak at altitude before the start attempt.

(d) Within route or track constraints, the objective would be met by attempting a start near the highest altitude assigned the route or track, and the final attempt near the lower altitude limits of the route or track, as defined by ATC. These altitudes should be representative of the ETOPS routes flown.

(e) If the APU fails to start on the first attempt, subsequent start attempts may be made within the limits of the airframe and APU manufacturer's recommended procedures.

(3) The certificate holder must report any operationally required APU in-flight start failures occurring during actual ETOPS operations to its CHDO within 96 hours. The certificate holder also must report any occurrences of an ETOPS configured APU in-flight unsuccessful start attempt occurring during routine sampling (which exceed the airframe and APU manufacturer design specifications) to its CHDO. The final report should include corrective actions taken as well as the status of corrective action programs and fleet upgrades.

n. Configuration Maintenance and Procedures (CMP).

(1) The CMP Standard specifies any additional configuration, maintenance or operational requirement that is uniquely applicable to ETOPS. The requirements in the CMP are established by the FAA at the time of initial ETOPS type design approval of the airplane-engine combination. The CMP document typically is published and maintained by the airplane manufacturer and includes identified CMP requirements. Airplane manufacturers may continue to release CMP revisions beyond the basic revision level required for ETOPS. The CMP revision levels required for specific airplane-engine combinations are typically listed in the front of the CMP or may be controlled through issuance of customized CMP documents. The certificate

holder must implement the basic configuration, maintenance, and operating procedures standard, identified in the CMP, before beginning ETOPS operations unless the CMP includes an incorporation schedule with a later date than the beginning of the certificate holder's ETOPS operations. If a CMP document exists for an ETOPS certificate holder's airplane, the certificate holder must ensure that all of the following apply:

(a) Configuration features are installed in the airplanes and engines;

(b) Maintenance procedures are incorporated into the maintenance program;

(c) Demonstrated capabilities are incorporated into the flight operations manual and the minimum equipment list, as required; and

(d) Operators must coordinate any deviation from the manufacturer's CMP requirements with the CHDO or Aircraft Certification Office, as required by the CMP document.

(2) Each certificate holder must develop a system to ensure all CMP requirements remain incorporated in its airplanes, programs, and manuals throughout the operational life of each airplane, for as long as they operate in ETOPS.

(3) The FAA will mandate any subsequent configuration, maintenance, or procedural changes necessary for continued safe ETOPS operations through the Airworthiness Directive (AD) process. The certificate holder should review and consider voluntarily incorporating any revised CMP standard that enhances airplane reliability and/or performance.

(4) The certificate holder should provide its CHDO a matrix detailing the CMP standard for its proposed ETOPS fleet. The matrix should specifically include each CMP item number, revision level, item description, and reference documentation describing the incorporation method and date.

o. Procedural Changes. Refer to Chapter 5, paragraph 502 for ETOPS maintenance and training program changes.

302. ETOPS MAINTENANCE TRAINING REQUIREMENTS.

a. The certificate holder is responsible for ensuring that all maintenance personnel who perform maintenance on its ETOPS airplanes, including repair stations, vendors, and contract maintenance, have received adequate technical training for the specific airplane-engine combination it intends to operate in ETOPS. The certificate holder should review the existing airplane-engine combination maintenance training program with its CHDO to ensure that it adequately provides the necessary training.

b. Additionally, the certificate holder must develop ETOPS specific training that focuses on the special nature of ETOPS and take measures to insure that this training is given to all personnel involved in ETOPS. ETOPS specific training is in addition to the certificate holder's accepted maintenance training program used to qualify individuals for specific airplanes and engines and may be included in the accepted maintenance training curricula. It thus, becomes the certificate holder's ETOPS training program. The goal of this training is to ensure that all

personnel involved in ETOPS properly accomplish ETOPS maintenance requirements. The certificate holder is responsible with acceptance from the CHDO to determine which personnel are involved in ETOPS, and ensure that each person's level of ETOPS training is commensurate with their level of involvement with ETOPS airplanes. Customarily, ETOPS training is intended for Line and Hanger Maintenance personnel, Centralized Maintenance Control personnel and Engineering personnel, where applicable, but it does not necessarily include the various shop level employees. For example, a mechanic who is performing pre-departure service checks may be required to have a higher level of ETOPS training and qualification than a mechanic performing routine tasks on non ETOPS significant systems during a heavy maintenance check. A technician working ETOPS significant systems in an HMV (Heavy Maintenance Visit) environment must be appropriately trained for ETOPS, but need not be ETOPS qualified. Recurrent training in all maintenance areas should be established and used to inform personnel involved in ETOPS about new equipment, requirements, operator programs, etc. Experience has shown recurrent training is a valuable instrument in "lessons learned" for ETOPS operations.

c. In the line maintenance environment, ETOPS-qualified maintenance personnel are those who have successfully completed the certificate holder's ETOPS qualification program, and who have satisfactorily performed extended range tasks under the direct supervision of an FAA-certificated maintenance person. The person giving the direct supervision must have had previous experience with maintaining the particular make and model airplane being used by the certificate holder. For new airplanes, it is understood the certificate holder may not have an FAA certified maintenance person available who has previous experience with the newly introduced make and model airplane. In this instance, the training received from the manufacturer's maintenance training program, or a comparable program would be acceptable.

303. ETOPS FLIGHT OPERATIONS REQUIREMENTS.

a. Airplane Performance Data. The certificate holder may not dispatch an airplane on an ETOPS flight unless it makes performance data available to its flight crewmembers and dispatchers that support all phases of ETOPS operations, including divert scenarios. This performance data will contain the following information:

(1) Detailed one-engine inoperative performance data including fuel flow for standard and nonstandard atmospheric conditions, which should be demonstrated as a function of airspeed and power setting, where appropriate. This data will cover:

(a) Driftdown (includes net performance);

(b) Cruise altitude coverage including 10,000 feet;

(c) Holding; and

(d) Altitude capability (includes net performance).

(2) Detailed all-engine-operating performance data, including nominal fuel flow data, for standard and nonstandard atmospheric conditions, which should be demonstrated as a function of airspeed and power setting, where appropriate. This data will cover:

(a) Cruise altitude coverage including 10,000 feet; and

(b) Holding.

(3) Details of any other conditions relevant to ETOPS that can cause significant deterioration of performance, such as ice accumulation on the unprotected surfaces of the airplane, RAM Air Turbine (RAT) deployment, and thrust reverser deployment if such data is available.

b. En Route Airport Information.

(1) In accordance with § 121.97, the certificate holder must maintain current status information on the operational capabilities of the airports designated for use as ETOPS alternates. "Public protection" has been a historic requirement for all domestic and flag operations. For ETOPS greater than 180 minutes and for operations traversing the North and South Polar Areas, this requirement has been expanded to include the listing of facilities at each airport, or in the immediate area, sufficient to protect the passengers and crew from the elements and to see to their welfare. Such a requirement can be interpreted to encompass the time from landing until satisfactory recovery of passengers and crew based on the certificate holder's passenger recovery plan required by § 121.135 and discussed in Chapter 4, paragraph 403c(5) of this AC.

(2) The certificate holder's program should provide flight crewmembers with current weather and information on a set of adequate airports in the ETOPS portion of the flight that are within the maximum diversion capability of the airplane on the planned route of flight as an aid to the flightcrew in contingency planning. Any appropriate facility information and other data concerning these airports should be provided to flight crewmembers in a clear, concise, userfriendly format for use when planning a diversion.

(3) Section 121.135 requires that any certificate holder conducting passenger flag operations must include in their flight operations manuals or equivalent documentation available to the flightcrews:

(a) For ETOPS greater than 180 minutes, a specific passenger recovery plan for each ETOPS Alternate Airport used in those operations; and

(b) For operations in the North Polar Area and South Polar Area, a specific passenger recovery plan for designated diversion airports.

c. Dispatch.

(1) Alternates. A certificate holder may not dispatch an airplane in ETOPS unless the required takeoff, destination and alternate airports, including ETOPS alternate airports are listed in the cockpit documentation (e.g., computerized flight plan) and are identified and listed in the dispatch release. Because ETOPS alternates serve a purpose different from that of a destination alternate, and may be used in the event of a diversion with an engine failure or loss of a primary airplane system, a certificate holder should not list an airport on the dispatch/flight release as an ETOPS alternate unless that airport's services and facilities are adequate for such a diversion. A

certificate holder of a two-engine airplane should exercise ETOPS beyond 180 minutes authority only if there are no ETOPS alternates that are within a 180-minute diversion distance from the planned route of flight. In addition, those adequate airports closest to the planned route of flight should be those first considered as ETOPS alternates.

(2) Flight Planning Limitation. The certificate holder's ETOPS flight planning program must ensure that the planned route of flight remains within the authorized ETOPS area of operation in accordance with § 121.633 as follows:

(a) For ETOPS up to and including 180 minutes and 207 minutes in the North Pacific Area of Operation, the time required to fly the distance to the planned ETOPS alternate, at the approved one-engine inoperative cruise speed in still air and standard conditions, may not exceed the time specified for the airplane's most time limited ETOPS significant system (including cargo fire suppression) minus 15 minutes.

(b) For ETOPS beyond 180 minutes, the time required to fly the distance to the planned ETOPS alternate, at the all-engines-operating cruise speed at the normal all-enginecruise altitude, correcting for wind and temperature, may not exceed the certified capability for the airplane's most limiting fire suppression system minus 15 minutes. Three- and four-engine turbine engine-powered airplanes not meeting these requirements as of the effective date of

§ 121.633 may continue ETOPS operations until February 15, 2013.

(c) Further, for ETOPS beyond 180 minutes, the time required to fly the distance to the planned ETOPS alternate, at the approved one-engine inoperative cruise speed at the normal one engine inoperative level off altitude, correcting for wind and temperature, may not exceed the certified capability for the airplane's most time limited ETOPS significant system (except for the most limiting fire suppression system) minus 15 minutes.

NOTE: Certificate holders flying three- and four-engine airplanes prior to the established installation time and certification time requirements of the regulation for these systems and their airplanes are exempt from these flight planning limitations. Once such required fire suppression systems are installed (no later than February 15, 2013) and once the ETOPS significant system time limits are established as required by appendix K of part 25, § K25.1.7 (no later than February 17, 2015), the operator must follow the flight planning limitations in §§ 121.633(b)(1) and 121.633(b)(2).

(3) Landing Distance. For the runway expected to be used, the landing distance available, as specified by the airport authority, must be sufficient based on airplane flight manual landing performance data to meet the landing distance limitations specified in § 121.197. The altitude of the airport, wind conditions, runway surface conditions, and airplane handling characteristics should be taken into account.

(4) Airport Rescue and Fire Fighting Service (RFFS).

(a) The following minimum International Civil Aviation Organization (ICAO) RFFS categories must be available at each airport listed as an ETOPS Alternate Airport in a dispatch or flight release:

1. ETOPS Up to 180 Minutes. ETOPS alternates with ICAO Category 4.

2. ETOPS Greater than 180 Minutes. ETOPS alternates with Category 4. In addition, the airplane must remain within the ETOPS authorized diversion time from an Adequate Airport that has RFFS equivalent to that specified by ICAO Category 7, or higher. The availability of Adequate Category 7 RFFS airports should be considered for the entire ETOPS segment of the planned route.

(b) If the necessary equipment and personnel are not immediately available at the airport, additional fire fighting support may be brought in from a nearby town or other location. The certificate holder must ensure that the nearby facility is capable of responding to a request for fire fighting assistance within a reasonable time. A 30-minute response time is deemed adequate if the initial notification to respond can be initiated while the diverting airplane is en route. A 30-minute response time does not imply that the firefighting equipment has to be at the airport within 30 minutes of the initial notification under all conditions. It does mean that such equipment must be available on arrival of the diverting airplane and remain on station as long as the services are needed.

(5) ETOPS Alternate Minima. A particular airport may be considered to be an ETOPS alternate for flight planning and dispatch purposes, if the latest available forecast weather conditions from the earliest time of landing to the latest time of landing at that airport, equals or exceeds the criteria detailed in the following table. Because OpSpecs alternate weather minima standards apply to all alternates, the following criteria is recommended for a typical certificate holder's OpSpecs. An individual certificate holder's OpSpecs must reflect current requirements (§ 121.625). Although no consideration for the use of GPS/RNAV approaches is presented here, operators may request to receive this authorization through the FAA. This authorization would be reflected in the operator's OpSpecs. Appropriate ETOPS alternate minima for such operations will be determined by the Director, Flight Standards Service. The airport of departure (takeoff) and the destination airport (unless used concurrently as an ETOPS alternate) are not required to meet the weather minima for ETOPS alternates as these airports are subject to other regulations (e.g., §§ 121.617, 121.621, and 121.623).

ETOPS Alternate Minimum

Approach Facility

Configuration

For airports with at least one operational navigational facility providing a straight-in non-precision approach procedure, or Category I precision approach, or, when

applicable, a circling maneuver from an instrument approach procedure.

For airports with at least two operational navigational facilities, each providing a straight-in approach procedure to different suitable runways.

One useable authorized Category IIILS IAP.

One useable authorized category III ILS Instrument Approach Procedure (IAP).

Alternate Airport IFR Weather Minimum Ceiling2

Add 400 ft to the MDA(H) or DA(H), as applicable.

Add 200 ft to the higher DA(H) or MDA(H) of the two approaches used.

300 feet

200 feet

Alternate Airport IFR

Weather Minimum

Visibility3

Add 1 sm or 1600m to the landing minimum.

Add lA sm or 800m4 to the higher authorized landing minimum of the two approaches used.

3/4 sm (1200 m) or RVR 4000 (1200 m)

1/2 sm (800 m)4 or RVR 1800 feet (550 m)

1 When determining the usability of an IAP, wind plus gust must be forecast to be within operating limits, including reduced visibility limits, and should be within the manufacturer's maximum demonstrated crosswind value.

2 Conditional forecast elements need not be considered, except that a PROB40 or TEMPO condition below the lowest applicable operating minima must be taken into account.

J When dispatching under the provisions of the MEL, those MEL limitations affecting instrument approach minima must be considered in determining ETOPS alternate minima.

4 For operations outside United States, because of variations in the international metric weather forecasting standards, 700m may be used in lieu of 800m.

(6) Fuel Supply. The certificate holder must comply with the ETOPS en route fuel supply as specified in § 121 .646(b) as follows:

(a) No person may dispatch or release for flight or takeoff a turbine enginepowered airplane in ETOPS unless, considering wind and other weather conditions expected, it has the fuel required by normal Flag or supplemental carrier requirements and enough fuel to satisfy paragraphs 1 through 4 below:

1. The greater amount of fuel sufficient to fly to an ETOPS alternate under the following three scenarios:

• Assuming a rapid decompression at the most critical point followed by descent to a safe altitude in compliance with the oxygen supply requirements of § 121.333, or

• At the approved one-engine inoperative cruise speed assuming a rapid decompression and a simultaneous engine failure at the most critical point followed by descent to a safe altitude in compliance with the oxygen supply requirements of § 121.333, or

• At the approved one-engine inoperative cruise speed assuming an engine failure at the most critical point followed by descent to the one-engine inoperative cruise altitude.

2. Upon reaching the alternate, hold at 1,500 ft above field elevation for 15 minutes and then conduct an instrument approach and land.

3. Add a 5 percent wind speed factor (that is, an increment to headwind or a decrement to tailwind) on to the actual forecast wind used to calculate fuel in paragraph 1 above to account for any potential errors in wind forecasting. If a certificate holder is not using the actual forecast wind based on a wind model acceptable to the FAA, the airplane must carry 5 percent of the fuel required for paragraph 1 above, as reserve fuel to allow for errors in wind data. A wind aloft forecast distributed worldwide by the World Area Forecast System (WAFS) is an example of a wind model acceptable to the FAA.

4. After completing the calculation in paragraph 3, compensate in paragraph 1 above with additional fuel for the greater of the following scenarios:

• The effect of airframe icing during 10 percent of the time during which icing is forecast (including ice accumulation on unprotected surfaces, and the fuel used by engine and wing anti-ice during this period). Unless a reliable icing forecast is available, icing may be presumed to occur when the total air temperature at the approved one-engine cruise speed is less than +10 degrees Celsius, or if the outside air temperature is between 0 degrees Celsius and -20 degrees Celsius with a relative humidity of 55 percent or greater

• Fuel for engine anti-ice, and if appropriate wing anti-ice, for the entire time during which icing is forecast

(b) Unless the certificate holder has a program established to monitor airplane inservice deterioration in cruise fuel burn performance, and includes in fuel supply calculations fuel sufficient to compensate for any such deterioration, increase the final calculated fuel supply by 5 percent to account for deterioration in cruise fuel burn performance.

(c) If the APU is a required power source, then its fuel consumption must be accounted for during the appropriate phases of flight.

(d) In computing the ETOPS alternate fuel supply, advantage may be taken of driftdown computed at the approved one-engine inoperative cruise speed. Accounting of wing anti-ice as in paragraph (6)(a)4 above may apply to some models of airplane based on their characteristics and the manufacturer's recommended procedures.

(7) Communications. The FAA has determined that the best way to assure clear and timely communication in general, is via voice communication. Likewise the FAA has determined that there is a significant safety benefit associated with an ETOPS flight having the ability to communicate via a satellite based voice system, especially for those situations that occur while on long, remote ETOPS routes. The need for safety is best served through information and technical assistance that is clearly and rapidly transmitted to the flightcrew in a way that requires the least amount of distraction to piloting duties. Other than the area north of 82 degrees latitude, satellite communications provides the best means to provide that capability because it is not limited by distance. The FAA recognizes the limitations of satellite communications (SATCOM) in the North Polar Area above this latitude, and in such an area an alternate communication system such as HF voice or data link is to be used. The relatively short period of time that the flight is above latitude 82 degrees North in relation to the total planned flight time is a small fraction of the total flight. The ability to use SATCOM for all other portions of the flight, which for some routes could be longer than 15 hours duration, is advantageous to the flight. For flights above 82 degrees North latitude, the operator must also ensure that communications requirements can be met by the most reliable means available, taking into account the potential communication disruption due to solar flare activity. The same philosophy and commensurate requirements apply for ETOPS in the South Polar Area.

(a) Section 121.99(a) includes a requirement for communications facilities that enable rapid and reliable communications on routes and altitudes that may be used. For all ETOPS each certificate holder conducting flag or supplemental operations in ETOPS must provide voice communications over routes where voice communications facilities are available. Where voice communication facilities are not available, and voice communication is not possible or is of poor quality, communications using alternative systems must be substituted.

(b) In addition to the communication requirement above, flag and supplemental certificate holders operating ETOPS beyond 180 minutes from an alternate must have a second communications system that is capable of providing immediate satellite-based voice communications of landline telephone fidelity such as SATCOM. This system must be capable of providing clear voice communications between the flight crewmember and ATC, and the

flight crewmember and operations (dispatch). Where clear satellite-based voice communications are not available, alternative communications systems must be substituted. If an operator has provided a satellite communication system for the crew to satisfy § 121.99(a), it is not necessary that the second communication system required for ETOPS beyond 180 minutes be satellite based.

(c) In determining whether such communications requirements discussed in paragraphs (a) and (b) above are available, the certificate holder must consider potential routes and altitudes needed for possible diversions to ETOPS alternates as well as the original planned routing.

(8) Dispatch/Flight Release.

(a) The following items must be listed in the dispatch or flight release for all ETOPS in accordance with § 121.687.

• ETOPS alternates; and • The authorized ETOPS diversion time under which the flight is dispatched or released.

(b) The pilot in command (PIC) should have access to the weather and status of services and facilities at all adequate airports with weather greater than approach minimums other than the designated ETOPS alternates along the planned route that could be used for diversion before accepting the flight release.

(c) If a flight is dispatched on a route that is greater than 180 minutes from an ETOPS alternate, the certificate holder must inform the flightcrew and give them the reason for the routes selection.

(9) Dispatch on a "Flight-by-Flight Exception" Basis. For two-engine airplane ETOPS approvals under the provisions of 207-minute ETOPS in the North Pacific Area of Operation, and 240-minute ETOPS in the North Polar Area, in the area north of the NOPAC area, and the Pacific Ocean area north of the equator, regulations limit the operator's use of this authority in these areas to an "exception" basis. This exception may only be used when an ETOPS alternate is not available within 180 minutes and is based on certain criteria.

(a) For 207-Minute ETOPS, exception criteria includes political or military concerns, volcanic activity, temporary airport conditions, and airport weather below dispatch requirements, or other weather related events.

(b) For 240-Minute ETOPS in the North Polar Area and in the Area North of NOPAC, exception criteria includes extreme conditions particular to these areas such as volcanic activity, extreme cold weather at en route airports airport, weather below dispatch requirements, temporary airport conditions and other weather related events. The certificate holder must establish the criteria to be used to decide what extreme weather precludes using an airport.

(c) For 240-Minute ETOPS in the Pacific Ocean Area north of the Equator, exception criteria includes political or military concern, volcanic activity, airport weather below dispatch requirements, temporary airport conditions and other weather related events.

NOTE: Certificate holders are required to maintain a record of their use of that authority for tracking purposes. When an operator is granted such authority, they may exercise this authority based on the conditions above without limit. There is currently no requirement for any specific format for

reporting 207- and 240-minute track usage.

d. En Route.

(1) PIC Authority. No part of this AC is to be interpreted as reducing the PIC's joint responsibility for determining that the flight can be safely conducted as planned before release. None of the guidance in this AC may be interpreted in any way to prejudice or limit the final authority and responsibility of the PIC for the safe operation of the airplane.

(2) Potential Diversion Airports after Departure.

(a) After departure, designated ETOPS alternates must continue to meet the requirements of original dispatch, except that the weather must remain at, or above, operating minima (§ 121.631(c)). The pilot and dispatcher should monitor the airports within the ETOPS area of operation that could be used for diversion for deterioration in the weather and limitations in the availability of facilities and services that would render an airport unsuitable for landing in the event of a diversion. During the course of the flight, the flight crewmembers should be informed of significant changes in conditions at the designated ETOPS alternates, particularly those conditions that would render an airport unsuitable for landing and improvement in airport weather to conditions above operating minima.

(b) In most ETOPS operations, the ETOPS entry point is a significant distance from the point of dispatch. To ensure the capability and availability of an en route alternate to support any en route contingencies, before an ETOPS flight proceeds beyond the ETOPS entry point, the certificate holder must evaluate the weather from the earliest to latest time of arrival at the designated ETOPS alternates, as well as the landing distances, airport services, and facilities. If any conditions, such as weather below landing minima, are identified that would preclude a safe approach and landing, the PIC should be notified and an additional ETOPS alternate selected where a safe approach and landing can be made. A revised flight plan should include information on the newly designated ETOPS alternates within the authorized area of operation. Information on the weather and capabilities (that is, emergency response, approach aids, navigation facilities, and airport infrastructure) of potential ETOPS alternates in the authorized area of operations should be available to the PIC. The maximum diversion time, determined by the newly selected ETOPS alternate, must not exceed the authorized ETOPS maximum diversion time listed in the certificate holder's OpSpec for that airplane and operating area that could have been applied at original dispatch.

(c) An operator is not required to turn back once the flight has gone beyond the ETOPS entry point if an unexpected worsening of the weather at the designated ETOPS alternate

airport drops the airport below operating landing minima (or any other event occurs that makes the runway at that airport unusable). The FAA requires that the PIC, in coordination with the dispatcher if appropriate, will exercise judgment in evaluating the situation and make a decision as to the safest course of action. This may be a turn back, re-routing to another ETOPS alternate airport, or continuing on the planned route. Should the operator become aware of a potential weather problem prior to the airplane entering the ETOPS stage of the flight, the rule allows the operator to designate a different alternate airport at the ETOPS entry point in order to continue the flight.

(3) Engine Failure.

(a) Section 121.565 requires the PIC of a two-engine airplane with one engine inoperative to land at the nearest suitable airport where, in the PIC's judgment after considering all relevant factors, a safe landing can be made. This determination is especially critical for ETOPS where the availability of suitable airports may be limited and the diversion decision is therefore more critical. The following is a list of some, but not all, factors that may be relevant in determining whether or not an airport is suitable, and are consistent with the ETOPS principle of protecting the diversion once it occurs:

Airplane configuration, weight, systems status, and fuel remaining; Wind and weather conditions en route at the diversion altitude; Minimum altitudes en route to the diversion airport; Fuel burn to the diversion airport; Airport's nearby terrain, weather, and wind; Availability and surface condition of runway; Approach navigation aids and lighting available; Rescue and fire fighting services (RFFS) at the diversion airport; Facilities for passenger and crewmember disembarkation, and accommodations; PIC's familiarity with the airport; and Information about the airport provided to the PIC by the certificate holder.

(b) When operating a two-engine airplane with one engine inoperative, none of the following factors should be considered sufficient justification to fly beyond the nearest suitable airport:

• The fuel supply is sufficient to fly beyond the nearest suitable airport; • Passenger accommodation other than passenger safety; and • Availability of maintenance and/or repair resources.

(c) If no more than one engine is shut down on an airplane that has three or more engines, § 121.565 permits the PIC to fly beyond the nearest suitable airport in point of time if the PIC determines that doing so is as safe as landing at the nearest suitable airport. In making a decision to fly beyond the nearest suitable airport, the PIC should consider all relevant factors and, in addition, consider the possible difficulties that may occur if the flight is continued beyond the nearest suitable airport. When an airplane with more than two engines bypasses a suitable

alternate, the PIC should carefully weigh the risk associated with the next possible failure, which could complicate or compound the current engine inoperative condition. The next possible failure could be a system failure or another engine failure, which in either case, would affect crew workload and their possible success in completing the associated abnormal approach and landing procedures. It is even possible that a contingency outside of the realm of a system failure, such as a passenger illness, could compound the crew's workload normally associated with the current failure condition.

(4) System Failure/Partial Failure.

(a) During ETOPS, the limited availability of diversion airports and extended diversion distances require that the impact of a system failure or partial failure be carefully evaluated. This should include a careful assessment of remaining systems and overall operational capability. Time permitting, full use should be made of the information available through the certificate holder's dispatch facility and a determination made by the PIC as to the plan for the safe continuation of the flight, that is whether it is safer to divert and land or to continue as planned under the circumstances.

(b) If, as a result of reevaluating airplane systems, a change in flight plan is required, the PIC should be provided revised flight plan information and an update of conditions, including weather conditions at designated ETOPS alternates. Dispatch should advise the flight crewmembers of additional airports on the planned route of flight that could be used for diversion. In no case may the maximum approved diversion authority of the operation be exceeded.

(5) Other Diversion Scenarios. During ETOPS an airplane may divert for reasons other than engine or systems failure such as medical emergencies, onboard fire, or decompression. The nature of the emergency, and its possible consequences to the airplane, passengers and crew, will dictate the best course of action suitable to the specific en route contingency. The flightcrew must decide on the best course of action based on all available information. The ETOPS Alternate Airports required by § 121.624 and designated for a particular flight provide one option to the PIC. However, these ETOPS alternates may not be the only airports available for the diversion and nothing in this guidance in any way limits the authority of the PIC.

e. ETOPS Procedures Documentation.

(1) The certificate holder should develop unique ETOPS flightcrew procedures for each of the flight operations requirements discussed in this section. These procedures should be contained in the applicable manual or information provided to the flightcrew. The manual or information provided to the flightcrew should also contain procedural information necessary to interface with ETOPS maintenance requirements such as;

• Fuel crossfeed valve operational check (if applicable); • Special ETOPS MEL requirements ; • APU in-flight start procedures (if applicable); • Engine Condition Monitoring (ECM) data recording procedures; and

• In-flight verification of ETOPS significant systems.

(2) The initial pilot flight manual ETOPS section and each revision must be submitted to the CHDO and approved before being adopted.

304. FLIGHT OPERATIONS TRAINING REQUIREMENTS.

a. ETOPS Unique Requirements. The certificate holder's approved training program for ETOPS should include training that describes the unique aspects of ETOPS. That training should include, but not be limited to:

(1) Diversion Decision Making. The certificate holder's training program should prepare flight crewmembers to evaluate probable propulsion and airframe systems malfunctions and failures. The goal of this training should be to establish flight crewmember competency in dealing with the most probable operating contingencies.

(2) Specific ETOPS Requirements. The certificate holder's ETOPS training program should provide and integrate training for flight crewmembers and dispatchers (if applicable), as listed below. The FAA will periodically evaluate a cross-section of these items.

(a) Flight planning, including contingency data, that is engine failure, decompression, and diversion equal time point.

(b) Flight progress monitoring and fuel tracking.

(c) Operational restrictions associated with dispatch under the minimum equipment list (MEL).

(d) Non-normal procedures including:

1. Abnormal and emergency procedures.

2. Systems failures and remaining airplane capability as it relates to the decision to divert or to continue.

3. Diversion.

4. Crewmember incapacitation.

5. A simulated approach and missed approach with only an alternate power source available, if the loss of two main alternating current electrical power sources with no APU electrical source available results in significant degradation of instrumentation to either pilot.

(e) Use of equipment specifically required for ETOPS operations such as cold weather gear and SATCOM.

(f) Procedures to be followed in the event that there is a change in conditions at an ETOPS alternate listed on the dispatch/flight release that would preclude a safe approach and landing.

(g) Procedures to be followed in the event that there is a change in conditions at other potential en route diversion airports that would preclude a safe approach and landing.

(h) Understanding and effective use of approved additional or modified equipment required for ETOPS.

(i) Fuel quantity comparison: the certificate holder's training program should identify fuel management procedures to be followed during the en route portion of the flight. These procedures should provide for an independent crosscheck of fuel quantity indicators, for example, fuel used, subtracted from the total fuel load, compared to the indicated fuel remaining.

(j) Fuel management: accounting for discrepancies between planned fuel remaining and actual fuel remaining for example estimated time of arrival ahead of or behind plan, gross weight, and/or altitude differences.

(k) Flightcrew procedures unique to ETOPS as listed above in the paragraph 303 e, ETOPS Procedures Documentation.

(3) Passenger Recovery Plan. The certificate holder must provide training to the flight crewmembers and dispatchers relative to their perspective roles in the certificate holder's passenger recovery plan (§ 121.415).

b. Check Airman Used in ETOPS. The certificate holder must designate check airmen specifically for ETOPS. The objective of the ETOPS check airman program should be to ensure standardized flight crewmember practices and procedures and also to emphasize the special nature of ETOPS. Only airmen with a demonstrated understanding of the unique requirements of ETOPS should be designated as a check airman.

c. Review of Training Programs and Operating Manuals.

(1) The purpose of the review is to verify the adequacy of information provided to training programs and operating manuals. The FAA will use the information resulting from these reviews as the basis for modification or updating flight crewmember training programs, operating manuals, and checklists, as necessary.

(2) The FAA will also continually review in-service experience of systems significant to ETOPS. The review includes system reliability levels and individual event circumstances, including crewmember actions taken in response to equipment failures or loss of capabilities.

CHAPTER 4. APPLICATIONS TO CONDUCT ETOPS

CHAPTER 4. APPLICATIONS TO CONDUCT ETOPS

400. ETOPS QUALIFICATIONS. The unique nature of ETOPS necessitates an evaluation of these operations to ensure that the certificate holder's proposed programs are effective. The FAA will review the certificate holder's documentation and training programs to validate that they are appropriate for ETOPS. To receive approval to conduct ETOPS the certificate holder must satisfy the following conditions:

a. Airplane. The specified airplane-engine combination listed in the certificate holder's application must have been certificated to the airworthiness standards of transport category airplanes and must be approved for ETOPS. Guidance for airplane ETOPS type design can be found in AC 25.1535-1 and § 121.162.

Continue reading ↓ 120 of 212 passages shown