AC 91-70B Oceanic and Remote Continental Airspace Operations
This advisory circular (AC) contains general information and detailed guidance for operators planning flights in oceanic and remote continental airspace, including authorizations needed for operations outside the continental United States (CONUS). This includes Performance-based Navigation (PBN) and Special Areas of Operation (SAO). The Federal Aviation Administration (FAA) revised this AC to focus on the evolving operations in airspace where air traffic control (ATC) provides procedural control. This AC is laid out in a chronological format, beginning with foundational information, followed by information on the training, authorizations, and equipment required to operate most efficiently in this airspace, and finishing with flight planning, flight execution, and contingency operations guidance. Our goal is to provide you with a template to guide you through planning and executing flight operations through oceanic and remote continental airspace. Information related to international operations in specific locales has been removed from this AC due to its transitory nature. Some region-specific information has been incorporated into the North Atlantic (NAT), West Atlantic Route System (WATRS)/Gulf of Mexico/Caribbean, and Pacific (PAC) Resource Guides (NAT PDF, West Atlantic, Caribbean, and Gulf of Mexico PDF, and PAC PDF). These online resource guides, along with the FAA Notices to Airmen (NOTAM) Domestic/International, provide the most current information available to pilots, aircraft dispatchers and other operational control personnel preparing for oceanic and international operations.We have also included hyperlinks to many documents, available free or for purchase. The dynamics of oceanic and remote continental airspace operations are such that they are constantly evolving, and it is incumbent on you, the operators, to closely monitor any changes.
This document is cancelled. Cancelled by 91-70C. Check the official source before relying on it.
AC 91-70B CHG 1_FAA Web
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Oceanic and Remote Continental
Airspace Operations
Date: 2/1/19 AC No: 91-70B Initiated by: AFS-400 Change: 1
1. PURPOSE OF THIS ADVISORY CIRCULAR (AC). The Federal Aviation Administration (FAA) (“we”) developed this AC to provide general information and guidance for commercial and General Aviation (GA) operators (“you”) planning flights in oceanic and remote continental airspace. This guidance includes the authorizations you need for operations in such airspace outside the continental United States (CONUS).
2. PRINCIPAL CHANGES. This change aligns this AC with the Future of Flight Standards reorganization. This change also adds standard information in Chapter 1 and updates references, hyperlinks, and formatting throughout the AC.
PAGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
Pages i thru v 10/4/16 Pages i thru iv 2/1/19
Pages 1-1 thru 1-3 10/4/16 Pages 1-1 thru 1-3 2/1/19
Pages 2-1 thru 2-8 10/4/16 Pages 2-1 thru 2-8 2/1/19
Pages 4-2 thru 4-8 10/4/16 Pages 4-2 thru 4-8 2/1/19
Pages 5-5, 5-7, and 5-9 thru 5-11 10/4/16 Pages 5-5, 5-7, and 5-9 thru 5-11 2/1/19
Pages 6-2, 6-3, 6-5, 6-7, 6-14, 6-15, and 6-17 thru 6-21 10/4/16 Pages 6-2, 6-3, 6-5 thru 6-7, 6-14 thru 6-16, and 6-18 thru 6-20
2/1/19
Pages 7-1 and 7-2 10/4/16 Pages 7-1 and 7-2 2/1/19
Pages A-1 thru A-8 and A-10 10/4/16 Pages A-1 thru A-6, A-8, and A-9
2/1/19
Pages B-1 and B-2 10/4/16 Pages B-1 and B-2 2/1/19
Page C-1 10/4/16 Page C-1 2/1/19
Pages D-1, D-4, and D-5 10/4/16 Pages D-1 and D-5 2/1/19
Page E-2 10/4/16 Page E-2 2/1/19
Remove Pages Dated Insert Pages Dated
Pages F-1 and F-3 10/4/16 Pages F-1 and F-3 2/1/19
Pages G-1, G-2, and G-5 10/4/16 Pages G-1, G-2, and G-5 2/1/19
Robert C. Carty Deputy Executive Director, Flight Standards Service
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Oceanic and Remote Continental
Airspace Operations
Date: 10/4/16 AC No: 91-70B Initiated by: AFS-400 Change:
This advisory circular (AC) contains general information and detailed guidance for operators planning flights in oceanic and remote continental airspace, including authorizations needed for operations outside the continental United States (CONUS). This includes Performance-based Navigation (PBN) and Special Areas of Operation (SAO). The Federal Aviation Administration (FAA) revised this AC to focus on the evolving operations in airspace where air traffic control (ATC) provides procedural control. This AC is laid out in a chronological format, beginning with foundational information, followed by information on the training, authorizations, and equipment required to operate most efficiently in this airspace, and finishing with flight planning, flight execution, and contingency operations guidance. Our goal is to provide you with a template to guide you through planning and executing flight operations through oceanic and remote continental airspace. Information related to international operations in specific locales has been removed from this AC due to its transitory nature.
Some region-specific information has been incorporated into the North Atlantic (NAT) Resource Guide for United States Operators, West Atlantic Route System, Gulf of Mexico, Caribbean Resource Guide for U.S. Operators, and Pacific Resource Guide for U.S. Operators. These online resource guides, along with the FAA Domestic/International Notices to Airmen (NOTAM), provide the most current information available to pilots, aircraft dispatchers and other operational control personnel preparing for oceanic and international operations. We have also included hyperlinks to many documents, available free or for purchase. The dynamics of oceanic and remote continental airspace operations are such that they are constantly evolving, and it is incumbent on you, the operators, to closely monitor any changes.
This AC neither is mandatory nor constitutes a regulation. When this AC uses mandatory language (e.g., “must” or “may not”), it is quoting or paraphrasing a regulatory requirement or prohibition. When this AC uses permissive language (e.g., “should” or “may”), it describes an acceptable means, but not the only means, of conducting that aspect of operations in oceanic and international airspace. However, if you use the means described in the AC, you must follow them in all important respects.
CONTENTS Paragraph Page
Chapter 1. General … 1-1
1.1 Purpose of This Advisory Circular (AC) … 1-1
1.2 Audience … 1-1
1.3 Where You Can Find This AC … 1-1
1.4 What This AC Cancels … 1-1
1.5 Fundamental Changes from Previous Edition … 1-1
1.6 Related Title 14 of the Code of Federal Regulations (14 CFR) Parts … 1-1
1.7 Related Reading Material (current editions) … 1-2
1.8 AC Feedback Form … 1-3
Chapter 2. Background Information for Operations in Oceanic and Remote
Continental Airspace … 2-1
2.1 The International Civil Aviation Organization (ICAO): Its Relationship to U.S. Aviation … 2-1
2.2 ICAO Annexes … 2-1
2.3 Applicability of U.S. and International Regulations … 2-3
2.4 ICAO Guidance Documents and Reference Material … 2-4
2.5 Authorization to Operate in SAOs … 2-6
2.6 Authorization Process Relative to SAO … 2-7
2.7 Web-Based Operations Safety System (WebOPSS) … 2-8
Chapter 3. Pilot Qualification and Training Guidance for International, Oceanic, and
Remote Continental Airspace Operations … 3-1
3.1 Operator/Pilot-in-Command (PIC) Responsibilities—International Operations … 3-1
3.2 Training Requirements for Oceanic and Remote Continental Airspace Operations … 3-1
Chapter 4. Communications, Navigation, and Surveillance Systems Guidance for
Operations in Oceanic and Remote Continental Airspace … 4-1
4.1 Communications, Navigation, and Surveillance Improvements—Impact on Air Traffic Services (ATS) … 4-1
4.2 Performance-Based Operations … 4-1
4.3 Voice Communications in Oceanic and Remote Continental Airspace … 4-3
4.4 CPDLC and Automatic Dependent Surveillance-Contract (ADS-C) … 4-5
ii
4.5 Data Link Systems—Operational Authorization to Use … 4-6
4.6 ATC in Oceanic and Remote Continental Airspace … 4-6
4.7 Special Use Airspace (SUA) … 4-8
4.8 Air Defense Identification Zones (ADIZ) … 4-8
4.9 World Geodetic System 1984 (WGS 84) … 4-9
Chapter 5. Flight Planning Guidance for International and Oceanic and Remote
Continental Airspace Operations … 5-1
5.1 Lead Time Requirements … 5-1
5.2 Preparing an Itinerary … 5-1
5.3 Crew Fatigue … 5-4
5.4 Required Paperwork/Documentation … 5-5
5.5 Entry to Foreign Airspace—Flight Plan Versus Formal Advance Permission … 5-7
5.6 Managing Risk in Oceanic and Remote Continental Airspace Operations … 5-7
5.7 Weather Forecasts and Other Meteorological Planning … 5-8
5.8 Notices to Airmen (NOTAM) … 5-9
5.9 Extended Operations (ETOPS) … 5-9
5.10 Polar Operations … 5-9
5.11 Areas with Limited ATS … 5-10
5.12 Rotorcraft Operations … 5-10
Chapter 6. Flight Execution Guidance for Operations in Oceanic and Remote
Continental Airspace … 6-1
6.1 General Information … 6-1
Table 6-1. Examples of Incorrectly Applied Conditional Clearances … 6-2
6.2 Flight Plan … 6-4
6.3 Aircraft Preflight Guidance … 6-6
6.4 En Route Guidance … 6-11
Chapter 7. In-Flight Contingency Guidance for Operations in Oceanic and Remote
Continental Airspace … 7-1
7.1 Contingency Procedures: When They May Be Needed … 7-1
7.2 Choosing the Correct Contingency Procedure … 7-1
7.3 Altimetry and/or Navigation Degradation … 7-2
7.4 Lost Communications Procedures … 7-2
iii
Appendix A. Abbreviations and Definitions … A-1
Appendix B. Special Areas of Operation and OpSpecs/MSpecs/LOAs … B-1
Appendix C. Unusual Weather Activity … C-1
Figure C-1. ICAO Volcanic Ash Advisory Centers … C-1
Figure C-2. Example of a National Oceanic and Atmospheric Administration Scales Activity Report … C-3
Appendix D. Sample Oceanic Checklist … D-1
Appendix E. IATA In-Flight Broadcast Procedure … E-1
Figure E-1. Map of IFBP Area of Applicability … E-4
Appendix F. Special Procedures for In-Flight Contingencies in Oceanic and Remote
Continental Airspace … F-1
Figure F-1. General Weather Deviation Procedures Model … F-5
Appendix G. Suggested Subjects for Inclusion in Oceanic and International Procedures
and/or an Operations Manual … G-1
iv
Chapter 1. GENERAL › 1.6 Related Title 14 of the Code of Federal Regulations (14 CFR) Parts.
CHAPTER 1. GENERAL
1.1 Purpose of This Advisory Circular (AC). The Federal Aviation Administration (FAA) (“we”) developed this AC to provide general information and guidance for commercial and General Aviation (GA) operators (“you”) planning flights in oceanic and remote continental airspace. This guidance includes the authorizations you need for operations in such airspace outside the continental United States (CONUS).
1.2 Audience. We have primarily targeted this AC at operators who do not yet have set procedures for flights through this type of airspace and can use this AC as a guide in developing their own procedures. We are also targeting GA pilots who do not fly regularly in oceanic and remote continental airspace and need a refresher on what to consider before, during, and after such a flight. Most commercial operators have company procedures for operations in oceanic and remote continental airspace. Those procedures have been accepted by FAA inspectors and conform to all relevant regulations and guidance. If you are working for one of these operators, this AC may serve to reinforce your company procedures.
1.3 Where You Can Find This AC. You can find this AC on the FAA’s website at http://www.faa.gov/regulations_policies/advisory_circulars.
1.4 What This AC Cancels. AC 91-70A, Oceanic and International Operations, dated August 12, 2010, is canceled. AC 91-70, Oceanic Operations, and the North Atlantic International General Aviation Operations Manual (NAT IGA) are also obsolete.
1.5 Fundamental Changes from Previous Edition. Procedures for operating in oceanic and remote continental airspace are constantly evolving, and you should closely monitor any changes. We revised this AC to point you to the most current sources of international material. In some cases, we refer you to a website. You can also find supplements to this material by starting at https://www.faa.gov or by calling an FAA Special Areas of Operation (SAO) specialist. Contact information for an SAO specialist can be obtained from the responsible Flight Standards (FS) office. You may also be able to find this contact information on the North Atlantic (NAT) Resource Guide for United States Operators, Pacific Resource Guide for U.S. Operators, and West Atlantic Route System, Gulf of Mexico, Caribbean Resource Guide for U.S. Operators. In this AC, we include specific guidance for authorizations and conformance with other FAA policy issues. Host nation Aeronautical Information Publications (AIP) and international Notices to Airmen (NOTAM) also contain the most recent information.
1.6 Related Title 14 of the Code of Federal Regulations (14 CFR) Parts.
• Part 91, §§ 91.1 through 91.21, 91.101 through 91.143, 91.151 through 91.159, 91.167 through 91.193, 91.203, 91.205, 91.209 through 91.217, 91.221, 91.225, 91.227, 91.303 through 91.319, 91.323, 91.509, 91.511, 91.605, 91.609, 91.703 through 91.715, and 91.903; and Appendix G.
1.7 Related Reading Material (current editions). › 1.7.3 FAA ACs.
• Part 121, §§ 121.11, 121.121, 121.163, 121.339, 121.351, 121.353, and 121.355; and Appendix G.
• Part 125, §§ 125.23, 125.45, 125.51, 125.203, 125.209, and 125.363.
• Part 135, §§ 135.3, 135.43, 135.145, 135.165, 135.167, and 135.183; and Appendix G.
1.7 Related Reading Material (current editions).
1.7.1 RTCA Documents. Available for purchase on the RTCA website at https://www.rtca.org/content/list-available-documents.
1. RTCA/DO-258/ED-100, Interoperability Requirements for ATS Applications Using ARINC 622 Data Communications.
2. RTCA/DO-306/ED-122, Safety and Performance Standard for Air Traffic Data Link Services in Oceanic and Remote Airspace (Oceanic SPR Standard).
1.7.2 FAA Technical Standard Orders (TSO).
1. TSO-C115, Flight Management System (FMS) Using Multi-Sensor Inputs.
2. TSO-C145, Airborne Navigation Sensors Using The Global Positioning System Augmented by the Satellite Based Augmentation System (SBAS).
3. TSO-C146, Stand-Alone Airborne Navigation Equipment Using The Global Positioning System Augmented by the Satellite Based Augmentation System (SBAS).
4. TSO-C196, Airborne Supplemental Navigation Sensors for Global Positioning System Equipment Using Aircraft-Based Augmentation.
1.7.3 FAA ACs.
1. AC 20-138, Airworthiness Approval of Positioning and Navigation Systems.
2. AC 20-140, Guidelines for Design Approval of Aircraft Data Link Communication Systems Supporting Air Traffic Services (ATS).
3. AC 20-150, Airworthiness Approval of Satellite Voice (SATVOICE) Equipment Supporting Air Traffic Service (ATS) Communication.
4. AC 90-80, Approval of Offshore Standard Approach Procedures, Airborne Radar Approaches, and Helicopter En Route Descent Areas.
5. AC 90-96, Approval of U.S. Operators and Aircraft to Operate Under Instrument Flight Rules (IFR) in European Airspace Designated for Basic Area Navigation (B-RNAV)/RNAV5 and Precision Area Navigation (P-RNAV).
Chapter 1. GENERAL › 1.8 AC Feedback Form.
6. AC 90-105, Approval Guidance for RNP Operations and Barometric Vertical Navigation in the U.S. National Airspace System and in Oceanic and Remote Continental Airspace.
7. AC 90-114, Automatic Dependent Surveillance-Broadcast Operations.
8. AC 90-117, Data Link Communications.
9. AC 91-85, Authorization of Aircraft and Operators for Flight in Reduced Vertical Separation Minimum (RVSM) Airspace.
10. AC 120-42, Extended Operations (ETOPS and Polar Operations).
11. AC 120-100, Basics of Aviation Fatigue.
12. AC 120-103, Fatigue Risk Management Systems for Aviation Safety.
13. AC 135-42, Extended Operations (ETOPS) and Operations in the North Polar Area.
1.8 AC Feedback Form. For your convenience, the AC Feedback Form is the last page of this AC. Note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this AC on the Feedback Form.
2.2 ICAO Annexes. › 2.2.6 Annex 6, Operation of Aircraft (3 parts).
CHAPTER 2. BACKGROUND INFORMATION FOR OPERATIONS IN OCEANIC
AND REMOTE CONTINENTAL AIRSPACE
2.1 The International Civil Aviation Organization (ICAO): Its Relationship to U.S. Aviation. As a charter member of ICAO, the United States has fully supported the organization’s goals from its inception in 1947. ICAO works to achieve the highest level of standards and procedures for aircraft, personnel, airways, and aviation services throughout the world. ICAO oversees the international standards ascribed to by its more than 190 Member States for navigation facilities, airports, weather, and radio services. Through active support and participation in ICAO, the FAA strives to improve worldwide safety standards and procedures. ICAO’s strategic objectives are to continue to establish and maintain Standard and Recommended Practices (SARP) for the safe and orderly development of international aviation. You should be familiar with the 19 ICAO Annexes, which contain more than 10,000 adopted SARPs.
Note: ICAO Member States are obligated to comply with the international SARPs contained in the 19 Annexes and supporting ICAO documents such as ICAO Document 4444, Procedures for Air Navigation Services—Air Traffic Management, and ICAO Document 7030, Regional Supplementary Procedures.
2.2 ICAO Annexes. Find all ICAO Annexes at the ICAO store at https://store.icao.int.
2.2.1 Annex 1, Personnel Licensing. Provides information on licensing of flightcrews, air traffic controllers, and aircraft maintenance personnel, including medical standards for flightcrews and air traffic controllers.
2.2.2 Annex 2, Rules of the Air. Contains visual flight rules (VFR) and instrument flight rules (IFR) for all operators.
2.2.3 Annex 3, Meteorological Services for International Air Navigation. Provides for meteorological services for international air navigation and reporting of meteorological observations from aircraft.
2.2.4 Annex 4, Aeronautical Charts. Contains specifications for aeronautical charts used in international aviation.
2.2.5 Annex 5, Units of Measurement to be Used in Air and Ground Services. Lists dimensional systems used in air and ground operations.
2.2.6 Annex 6, Operation of Aircraft (3 parts). Specifies minimum standards for below-listed operations throughout the world:
1. Part I, International Commercial Air Transport—Aeroplanes.
2. Part II, International General Aviation—Aeroplanes.
3. Part III, International Operations—Helicopters.
2.2 ICAO Annexes. › 2.2.16 Annex 16, Environmental Protection:
2.2.7 Annex 7, Aircraft Nationality and Registration Marks. Specifies requirements for registration and identification of aircraft.
2.2.8 Annex 8, Airworthiness of Aircraft. Specifies uniform procedures for certification and inspection of aircraft.
2.2.9 Annex 9, Facilitation. Provides for the standardization and simplification of border-crossing formalities.
2.2.10 Annex 10, Aeronautical Telecommunications:
1. Volume I, Radio Navigation Aids. Provides for standardizing communications equipment and systems.
2. Volume II, Communication Procedures Including Those With PANS Status. Standardizes communications procedures.
3. Volume III, Communications Systems. Standardizes communications systems.
4. Volume IV, Surveillance Radar and Collision Avoidance Systems. Standardizes surveillance radar and collision avoidance.
5. Volume V, Aeronautical Radio Frequency Spectrum Utilization. Standardizes aeronautical radio spectrum utilization.
2.2.11 Annex 11, Air Traffic Services. Includes information on establishing and operating air traffic control (ATC), flight information, and alerting services.
2.2.12 Annex 12, Search and Rescue. Provides information on organization and operation of facilities and services necessary for Search and Rescue (SAR).
2.2.13 Annex 13, Aircraft Accident and Incident Investigation. Provides for uniformity in notifying, investigating, and reporting on aircraft accidents.
2.2.14 Annex 14, Aerodromes:
1. Volume I, Aerodrome Design and Operations. Contains specifications for the design and equipment of aerodromes.
2. Volume II, Heliports. Contains specifications for the design and equipment of heliports.
2.2.15 Annex 15, Aeronautical Information Services. Includes methods for collecting and disseminating aeronautical information required for flight operations.
2.2.16 Annex 16, Environmental Protection:
1. Volume I, Aircraft Noise. Contains specifications for aircraft noise certification, noise monitoring, and noise exposure units for land-use planning.
2.3 Applicability of U.S. and International Regulations. › 2.3.2 Differing Airspace Requirements.
2. Volume II, Aircraft Engine Emissions. Contains specifications for aircraft engine emissions.
3. Volume III, Aeroplane CO2 Emissions.
2.2.17 Annex 17, Security. Specifies methods for safeguarding international civil aviation against unlawful acts of interference.
2.2.18 Annex 18, The Safe Transport of Dangerous Goods by Air. Contains specifications for labeling, packing, and shipping dangerous cargo.
2.2.19 Annex 19, Safety Management. Describes Safety Management System (SMS) development, regulatory framework, and supporting guidance.
2.3 Applicability of U.S. and International Regulations.
2.3.1 Regulatory Obligations. You must adhere to U.S. regulations, ICAO SARPs, and the “flight and maneuver” regulations of the countries you overfly or in which you land. The Aeronautical Information Publication (AIP) from each country is an important source of information and reference. The U.S. AIP, for example, includes a detailed description of where U.S. aviation regulations differ from ICAO SARPs and procedures. You will see similar listings of “differences” in other State AIPs.
2.3.1.1 You should be especially familiar with ICAO Annex 2 and whichever part of ICAO Annex 6 applies to your operation.
2.3.1.2 Title 14 CFR part 91, § 91.703 stipulates that you are bound by ICAO Annex 2 if you operate your U.S.-registered aircraft outside the United States.
2.3.1.3 In all cases, § 91.703 requires that you follow the rules of the countries that you overfly and those in which you intend to land. If the part of 14 CFR under which you operate conflicts with the rules of the country you are operating over/in, you must follow the rules of that country.
2.3.1.4 According to 14 CFR part 121, § 121.11 and part 135, § 135.3(a)(2), for operations under each respective part, when operating within a foreign country, you must comply with the air traffic rules of the country concerned and any local airport rules that may be in force. You must also follow all rules of that part that are more restrictive than the rules of the foreign country in which you are operating, as long as you can do so without violating the rules of that country.
2.3.2 Differing Airspace Requirements. It is quite possible to transit regions with significantly different procedures in one long-range flight. Therefore, you should familiarize yourself with the equipment and procedural requirements to file and fly in each segment of foreign airspace in which you intend to operate by referencing, for example, the appropriate State’s AIP.
2.4.3 ICAO Recommended Guidance Documents. › 2.4.3.2 ICAO Document 7030, Regional Supplementary Procedures (SUPPS).
2.4 ICAO Guidance Documents and Reference Material. Find the following ICAO documents at the ICAO store at https://store.icao.int.
2.4.1 Guidance Documents. We developed much of the material in this AC from these foundational documents: ICAO Annexes, other ICAO guidance documents, related sections of 14 CFR, and other FAA guidance material.
2.4.2 The Convention on International Civil Aviation. We single out the following articles of ICAO Document 7300/9, Convention on International Civil Aviation, because of their importance in regulating international aviation. If you operate in oceanic and remote continental airspace, you should thoroughly understand them.
• Article 1, Sovereignty.
• Article 12, Rules of the Air.
• Article 29, Documents Carried in Aircraft.
2.4.3 ICAO Recommended Guidance Documents. Similar to our ACs, ICAO’s Recommended Guidance Documents provide guidance and information intended to facilitate the uniform application of SARPs contained in the 19 Annexes to ICAO Document 7300/9. Therefore, you should familiarize yourself with the following documents (current editions) prior to undertaking operations in oceanic and remote continental airspace.
Note: Ensure you understand the primacy relationship between the various ICAO documents. For example, ICAO Annex 2 details loss of communications procedures, which it points out you are expected to follow unless amended by regional agreement. In this case, you would then consult ICAO Document 7030 to review the loss of communications guidance for a specific geographical area. FAA principal inspectors (PI) and Special Areas of Operation (SAO) specialists can help you understand the relationship between various ICAO documents.
2.4.3.1 ICAO Document 4444, Procedures for Air Navigation Services—Air Traffic Management. These procedures complement the SARPs contained in ICAO Annex 2 and Annex 11 and specify, in greater detail than in the SARPs, the actual procedures Air Traffic Service (ATS) units apply when providing various services to air traffic.
2.4.3.2 ICAO Document 7030, Regional Supplementary Procedures (SUPPS). For each ICAO region, Document 7030 provides detailed procedures designed to meet those needs of specific areas that are not covered in the worldwide provisions contained in the Annexes and Procedures for Air Navigation Services (PANS) documents. The SUPPS complement the statement of requirements for facilities and services contained in the Air Navigation Plan publications.
2.4.3 ICAO Recommended Guidance Documents. › 2.4.3.8 ICAO Document 10038, Satellite Voice Guidance Material.
2.4.3.3 ICAO Document 8168, Procedures for Air Navigation Services—Aircraft Operations, Volume I, Flight Procedures. Document 8168, Volume I, describes operational procedures for flight operations personnel. It also outlines the various parameters upon which the safety criteria in Volume II, Construction of Visual and Instrumental Flight Procedures, are based in order to illustrate the need for all operational personnel to adhere strictly to the published procedures in order to maintain an acceptable level of safety in operations.
2.4.3.4 ICAO Document 9574, Manual on a 300m (1,000 ft) Vertical Separation Minimum Between FL 290 and FL 410 Inclusive. Document 9574 provides States’ regional planning groups with a basis for the revision of documents, procedures, and programs to enable the maintenance of a 300m (1,000 ft) vertical separation minimum between flight level (FL) 290 and FL 410 inclusive, in accordance with the criteria and requirements developed by ICAO. It provides guidance to State aviation authorities on those measures necessary to ensure that the criteria and requirements are met within their area of responsibility, as well as background information for operators to assist in the development of operating manuals and flightcrew procedures.
2.4.3.5 ICAO Document 9613, Performance-based Navigation (PBN) Manual. This manual provides practical guidance to States, air navigation service providers (ANSP), and airspace users on how to implement Area Navigation (RNAV) and Required Navigation Performance (RNP) applications, and how to ensure that the performance requirements are appropriate for the planned application.
2.4.3.6 ICAO Document 9869, Performance-Based Communication and Surveillance (PBCS) Manual. This guidance material explains the concepts of Required Communication Performance (RCP) and Required Surveillance Performance (RSP), identifies RCP and RSP requirements applicable to the provision and use of ATS, and provides a basis for the application of RCP and RSP in a specified airspace.
2.4.3.7 ICAO Document 10037, Global Operational Data Link (GOLD) Manual. The GOLD Manual addresses data link service provision, operator readiness, controller and flightcrew procedures, performance-based specifications, and post-implementation monitoring and analysis. GOLD provides guidance and information concerning data link operations and is intended to facilitate the uniform application of ICAO SARPs contained in ICAO Annex 2, Annex 10, and Annex 11; the provisions in ICAO Document 4444; and, when necessary, ICAO Document 7030.
2.4.3.8 ICAO Document 10038, Satellite Voice Guidance Material. This document is intended to maximize the operational benefits of Satellite Voice (SATVOICE) implementations by promoting seamless and interoperable SATVOICE operations throughout the world. The document provides
Chapter 2. › 2.5 Authorization to Operate in SAOs.
guidance and information concerning SATVOICE communications for aeronautical use and is intended to facilitate the uniform application of ICAO SARPs contained in ICAO Annex 2, the provisions in ICAO Document 4444, and, when necessary, ICAO Document 7030.
2.4.3.9 ICAO NAT Document 007, North Atlantic Operations and Airspace Manual. This document provides information for aircraft operating agencies, pilots, and dispatchers planning and conducting operations in or above the North Atlantic High Level Airspace (NAT HLA) (formerly known as Minimum Navigation Performance Specifications Airspace (MNPSA), effective February 2016). It also offers guidance to the State regulators responsible for the approval/certification/licensing of such aircraft operators, pilots, or dispatchers.
Note: General Aviation (GA) operators flying below NAT HLA should pay particular attention to Chapter 17, Flight Operations Below the NAT HLA, of this document. Information in the North Atlantic International General Aviation Operations Manual (NAT IGA) was incorporated into ICAO NAT Document 007 in 2013. Much of the information previously included in the NAT IGA has been updated and included here. The NAT IGA is no longer maintained as a separate document.
2.4.4 Other References:
1. Applicable FAA Domestic/International Notices to Airmen (NOTAM).
2. U.S. AIP and applicable foreign AIPs. Refer to the current AIP for any States whose airspace you intend to operate in/through. The AIP is the State’s official publication that defines and describes the airspace, aeronautical facilities, services, and national rules and practices pertaining to air traffic, particularly if they differ from ICAO SARPs (so-called “differences” are listed in AIPs).
3. Regulations of the foreign countries over which you intend to fly.
4. The customs procedures, cultural considerations, entry and overflight procedures, and health and safety precautions for each country in which you intend to land.
5. The oceanic and remote section of the FAA’s Flight Operations Group web page, found at http://www.faa.gov/about/office_org/headquarters_offices/ avs/offices/afx/afs/afs400/afs410/oceanic_remote.
2.5 Authorization to Operate in SAOs. SAOs are areas with unique characteristics that require you to use special equipment, procedures, and/or techniques to safely conduct your flight operations. In some SAOs, the ATC system supports an increased airspace capacity by reducing required separation between aircraft. This reduction in separation requires improved levels of performance and in some cases more stringent procedures.
2.6 Authorization Process Relative to SAO. › 2.6.5 Phase 5.
To fly in airspace considered an SAO, you need to obtain an operational authorization from the Administrator in the form of an operations specification (OpSpec), a management specification (MSpec), or a Letter of Authorization (LOA), depending on what part of 14 CFR governs your operations.
1. If you operate under 14 CFR part 121, 125, or 135, you require OpSpecs.
2. GA operators under parts 91 and 125 (including part 125 Letter of Deviation Authority (A125 LODA) holders) may require LOAs.
3. If you are a fractional ownership operator under part 91 subpart K (part 91K), you require MSpecs.
4. You can find a list of common oceanic and remote and SAO-specific OpSpecs/MSpecs/LOAs in Appendix B, Special Areas of Operation and OpSpec/MSpec/LOA. SAO specialists will have the most up-to-date information regarding airspace or capabilities requirements requiring approval.
5. The North Atlantic (NAT) Resource Guide for United States Operators, West Atlantic Route System, Gulf of Mexico, Caribbean Resource Guide for U.S. Operators, and Pacific Resource Guide for U.S. Operators include detailed charts that provide cross references for various oceanic OpSpecs/MSpecs/LOAs and associated guidance documents.
2.6 Authorization Process Relative to SAO. We have developed a five-phase process for you to gain approval for a desired operation. The responsible Flight Standards (FS) office can provide you with the details pertinent to each phase and your specific requirements.
2.6.1 Phase 1. You determine a need for authorization and contact the FAA.
2.6.2 Phase 2. You formally submit a proposal for FAA evaluation.
2.6.3 Phase 3. We evaluate the request and determine what level of demonstration is required. We may conduct the demonstration within the responsible FS office, at your site of operations, or at both facilities.
2.6.4 Phase 4. We observe and evaluate a demonstration of your ability to perform in accordance with your proposal. This is an operational evaluation. If you don’t pass, we will notify you at this time.
Note: Flight or line observations are not required for GA LOA applications. For GA operators, we evaluate your application and normally conduct an in-person knowledge validation (tabletop exercise and/or static airplane demonstration).
2.6.5 Phase 5. If you pass the evaluation, we approve your proposal. We will grant approval by issuing an OpSpec/MSpec/LOA.
2.7 Web-Based Operations Safety System (WebOPSS). › 2.7.2 WebOPSS Training.
2.7 Web-Based Operations Safety System (WebOPSS).
2.7.1 WebOPSS Access. WebOPSS is the FAA’s regulatory document management system for issuing OpSpecs, MSpecs, and LOAs to air operators as indicated in 14 CFR. Authorized aviation industry personnel can apply for access to WebOPSS through their PIs. WebOPSS access allows industry personnel to view and propose changes to their authorizations, which can expedite applications.
2.7.2 WebOPSS Training. You will require training prior to receiving WebOPSS access. You can accomplish the training either through an FAA inspector or by taking the WebOPSS formal training course through the FAA’s Mike Monroney Aeronautical Center (MMAC).
3.2 Training Requirements for Oceanic and Remote Continental Airspace… › 3.2.1 Commercial Operator Training.
10/4/16 AC 91-70B
CHAPTER 3. PILOT QUALIFICATION AND TRAINING GUIDANCE FOR INTERNATIONAL, OCEANIC, AND REMOTE CONTINENTAL AIRSPACE
OPERATIONS
3.1 Operator/Pilot-in-Command (PIC) Responsibilities—International Operations.
3.1.1 Operator Responsibilities. In Annex 6, ICAO makes the following stipulations for flights outside the jurisdiction of Member States:
1. An operator will ensure that all employees, when abroad, know that they must comply with the laws, regulations, and procedures of those States where they conduct operations.
2. An operator will ensure that all pilots are familiar with the laws, regulations, and procedures pertinent to the performance of their duties prescribed for the areas traversed, the airports used, and the related air navigation facilities.
3. The operator will ensure that other members of the flightcrew are familiar with these laws, regulations, and procedures that are pertinent to the performance of their respective duties in the operation of the aircraft.
3.1.2 PIC Responsibilities. As a PIC conducting flight operations in international airspace, you must:
1. Comply with the relevant laws, regulations, and procedures of the United States.
2. Assume responsibility for the operation and safety of the aircraft and for the safety of all persons aboard your aircraft during flight time.
3. Notify the appropriate Air Traffic Service (ATS) unit, as soon as circumstances permit, of actions you took in an emergency which necessitated immediate action and involved a violation of local regulations or procedures. Ensure they understand that you took this action under your emergency authority as PIC. You must also submit a report on any such violation to the appropriate authority of that State, if required.
4. Notify the nearest appropriate authority, by the quickest means available, in the event of an accident or incident involving the airplane which results in the serious injury or death of any person, or results in substantial damage to the airplane or property.
3.2 Training Requirements for Oceanic and Remote Continental Airspace Operations.
3.2.1 Commercial Operator Training. Operators (other than GA operators) conducting flights in oceanic and remote continental airspace are required to have training approved by the Administrator. Your training programs will receive approval in conjunction with your company’s certification and prior to our issuance of OpSpecs or MSpecs.
3.2 Training Requirements for Oceanic and Remote Continental Airspace… › 3.2.3 Relevant Subject Matter.
10/4/16 AC 91-70B
3.2.2 GA Training. If you are a GA pilot desiring to fly in oceanic and remote continental airspace, you may need operational approval via an LOA (see paragraph 2.5). One or more of the following actions may satisfy the requirements for us to issue an LOA:
1. Completing an operator’s oceanic operations training program.
2. Completing a commercial oceanic operations training program.
3. Submitting military training records indicating prior oceanic operations experience.
4. Using other methods indicating that you can safely conduct oceanic operations. Examples could include written testing, oral testing, or evidence of prior experience.
3.2.3 Relevant Subject Matter. The following items are examples of the subject matter with which you should be familiar in order to conduct operations in oceanic and remote continental airspace:
1. Title 14 CFR (applicable parts).
2. ICAO SARPs.
3. ICAO measurement standards.
4. Use of oceanic flight planning charts.
5. Sources and content of international flight publications.
6. Itinerary planning and overflight clearances.
7. Meteorology, including significant weather (SIGWX) charts, prognostic weather charts, tropopause prognostic charts, and Terminal Aerodrome Forecasts (TAF), as well as contingency procedures for weather diversions.
8. Preparation of international flight plans, plotting charts, and operational flight plans/flight logs, to include ETP calculations. These include the Communications, Navigation, and Surveillance capability codes appropriate to your aircraft and your operational authorization.
9. Specific airspace requirements, to include communications, navigation, and surveillance equipment requirements, as well as operational procedures related to Reduced Vertical Separation Minimum (RVSM) and RNP.
10. Long-range, air-to-ground communication procedures, including all data link and satellite communications (SATCOM) voice operations, as applicable.
11. En route and terminal procedures—differences from U.S. procedures.
12. Use of oceanic checklists.
13. Oceanic error risk mitigations.
14. Understanding of Strategic Lateral Offset Procedures (SLOP).
15. Air traffic clearances, to include proper terminology and phraseology.
10/4/16 AC 91-70B
16. Emergency and contingency procedures (see Appendix F, Special Procedures for In-Flight Contingencies in Oceanic and Remote Continental Airspace), including required emergency equipment, SAR techniques, navigation equipment failure techniques, and communication equipment failure techniques.
17. Specialized training, if conducting operations in areas of magnetic unreliability (AMU), as applicable.
18. Use of polar/remote area checklists.
19. Polar/remote area error risk mitigations.
4.2.2 RCP. › 4.2.2.1 RCP 240 requires a 99.9 percent probability (continuity) the…
10/4/16 AC 91-70B
CHAPTER 4. COMMUNICATIONS, NAVIGATION, AND SURVEILLANCE
SYSTEMS GUIDANCE FOR OPERATIONS IN OCEANIC AND REMOTE
CONTINENTAL AIRSPACE
4.1 Communications, Navigation, and Surveillance Improvements—Impact on Air Traffic Services (ATS).
4.1.1 Technological Advances. Technological advances in ground-based computers, space-based signals, and aircraft communications, navigation, and surveillance systems all contribute to an air traffic system that provides increased navigational accuracy and allows you and your aircraft to interact more quickly with controllers. These advances have also improved controller-pilot communications, navigation accuracy, and aircraft surveillance reporting. This enhanced communications, navigation, and surveillance capability greatly reduces the errors and retransmissions that hampered oceanic flights just a few years ago. These safety improvements have facilitated corresponding improvements in efficiency and capacity, where aircraft are now allowed to fly closer to each other (separation minima have been reduced). Regional airspace managers continually update equipment requirements, making it incumbent on you to fully understand the current equipment, training, and authorization requirements for any airspace in which you intend to operate.
4.1.2 Automatic Dependent Surveillance-Broadcast (ADS-B). ADS-B supports these improvements by providing a higher update and enhanced accuracy of surveillance information over the current radar-based surveillance systems. ADS-B Out capability will be required, beginning January 1, 2020, for operations throughout much of the U.S. National Airspace System (NAS). A number of other countries are also implementing widespread use of ADS-B.
4.2 Performance-Based Operations.
4.2.1 Measures of Performance. Performance-based operations relies on Required Communication Performance (RCP), Required Navigation Performance (RNP), and Required Surveillance Performance (RSP). It uses these three primary measures of performance to determine required separation between flights, both in radar contact and in oceanic and remote continental airspace. ATS providers determine separation requirements based on a combination of these three performance indicators.
4.2.2 RCP. RCP establishes aircraft/controller communications timeline, equipment, and flightcrew training standards. Generally, you can measure RCP in terms of the timeline required to complete the communication transaction and the continuity, availability, and integrity of the transaction. In oceanic and remote continental airspace, RCP 240 and RCP 400 are the prevalent performance standards.
4.2.2.1 RCP 240 requires a 99.9 percent probability (continuity) the communications transaction will complete in less than 240 seconds (timeline). It also requires a 99.99 percent probability the communication can be initiated (availability) and
4.2.4 RSP. › 4.2.4.1 RSP 180 requires a 99 percent probability (continuity) the…
no more than 10-5 communications transaction malfunctions per flight-hour (integrity).
4.2.2.2 RCP 400 requires a 99.9 percent probability (continuity) the communications transaction will complete in less than 400 seconds (timeline). It also requires a 99.9 percent probability the communication can be initiated (availability) and no more than 10-5 communications transaction malfunctions per flight-hour (integrity).
4.2.2.3 For additional details, please see the current editions of the International Civil Aviation Organization (ICAO) Document 10037, Global Operational Data Link (GOLD) Manual, Appendix B, RCP Specifications, and ICAO Document 9869, Performance-based Communication and Surveillance (PBCS) Manual, at https://store.icao.int.
4.2.3 RNP. RNP establishes aircraft navigation accuracy, equipment, and flightcrew training standards. ICAO Document 9613, Performance-based Navigation (PBN) Manual, outlines these standards. Generally, we measure these standards in terms of accuracy, integrity, continuity, availability, and functionality. Oceanic and remote continental airspace ATS providers primarily provide RNP 10- (also known as Area Navigation (RNAV) 10) and RNP 4-based separation minima. RNP 2 applications have also become available for oceanic and remote continental airspace, to be used by individual States as necessary to meet their airspace requirements. In all cases, ATS providers will determine separation minima between adjacent aircraft based on the authorized capability each aircraft operator files in the flight plan.
1. RNP 10 requires an aircraft to be capable of remaining within 10 nautical miles (NM) of centerline 95 percent of the time and within 20 NM 99.999 percent of the time.
2. RNP 4 requires an aircraft to be capable of remaining within 4 NM of centerline 95 percent of the time and within 8 NM 99.999 percent of the time.
3. RNP 2 requires an aircraft to be capable of remaining within 2 NM of centerline 95 percent of the time and within 4 NM 99.999 percent of the time.
4.2.4 RSP. RSP establishes aircraft/controller surveillance timeline and equipment standards. Generally, you can measure RSP in terms of the timeline required to complete the transaction and the continuity, availability, and integrity of the transaction. In oceanic and remote continental airspace, RSP 180 and RSP 400 are the prevalent performance standards.
4.2.4.1 RSP 180 requires a 99 percent probability (continuity) the surveillance transaction will complete in less than 180 seconds (timeline). It also requires a 99.99 percent probability the communication can be initiated (availability) and no more than 10-5 communications transaction malfunctions per flight-hour (integrity).
4.3.1 High Frequency (HF) Radio Communications. › 4.3.1.1 HF radio calls are normally relayed electronically, via…
4.2.4.2 RSP 400 requires a 99 percent probability (continuity) the surveillance transaction will complete in less than 400 seconds (timeline). It also requires a 99.9 percent probability the communication can be initiated (availability) and no more than 10-5 communications transaction malfunctions per flight-hour (integrity).
4.2.4.3 For additional details, please see ICAO Document 10037, Appendix C, RSP Specifications.
4.2.5 Access to Performance-Based Routes. The communications, navigation, and surveillance capabilities of your crew and equipment determine your eligibility for operations specification (OpSpec)/management specification (MSpec)/Letter of Authorization (LOA) authorizations that enable you to take advantage of the performance-based routes in oceanic and remote continental airspace. The significant improvements in communications, navigation, and surveillance systems have allowed air traffic controllers to reduce separation between aircraft, expanding access to the routes that offer you the maximum savings in time and fuel.
Note: For a list of pertinent OpSpecs/MSpecs/LOAs, please see Appendix B, Special Areas of Operation and OpSpecs/MSpecs/LOAs.
4.3 Voice Communications in Oceanic and Remote Continental Airspace. ICAO Annex 6 (all three parts) requires those airplanes operating under instrument flight rules (IFR) to have installed and approved radio communication equipment capable of conducting two-way communications at any time during the flight. When operating over the high seas, ICAO Annex 2 requires you to equip your aircraft with a functioning two-way radio, to establish two-way radio communications with the appropriate air traffic control (ATC) unit, and to maintain a continuous listening watch on the appropriate radio frequency.
Note: It is not acceptable to depend solely on radio relay operations to satisfy this requirement. The appropriate authority for the airspace where you conduct the flight may prescribe the aeronautical stations and frequencies used for two-way communications.
4.3.1 High Frequency (HF) Radio Communications. HF radios have been in use for almost a century over oceanic and remote continental areas. As technological advances lead to more sophisticated methods of communication, HF equipment has also improved. HF radios now offer digital tuning, compact size, selective calling systems (SELCAL) (see below), and new antenna concepts. Consider the following when using HF communications:
4.3.1.1 HF radio calls are normally relayed electronically, via keyboard and display, to air traffic controllers by a radio operator. There is often a delay between your requests and ATC clearance. The radio operator does not have the authority to approve your request and must coordinate with the appropriate controller for that approval.
4.3.2 SELCAL. › 4.3.2.3 Efforts are underway to increase the number of codes by…
4.3.1.2 Communications over HF radio rely heavily on proper radio terminology and scripted reports. Use the published guidance found in en route publications or the Aeronautical Information Manual (AIM) to make sure you deliver messages in the proper format. Speak at a moderate speed using the internationally accepted phraseology. You may find ICAO standard phraseology in ICAO Document 9432, Manual of Radiotelephony. This document and other ICAO reference materials can be found on ICAO’s website at https://store.icao.int.
4.3.1.3 If ATC uses the terms “expect” or “when are you able,” they have not granted you a clearance. Typically, oceanic radio operators will use the phraseology “ATC clears…” when relaying a clearance.
4.3.1.4 You must read back every clearance received from ATC. Ensure that ATC acknowledges your exact read back to confirm that you correctly heard the instructions.
4.3.1.5 In general, higher frequencies (above 10.0 megahertz (MHz)) work better during daylight and lower frequencies (below 10.0 MHz) at night. It is not uncommon to use several frequencies on one flight while communicating with the same ATS provider.
4.3.1.6 HF communications are dependent on transmitted signals striking the ionosphere and reflecting back to antennae at ground stations. The ionosphere is susceptible to interference from space weather, resulting in periods where HF reception is marginal or unreadable. You may especially notice this phenomenon in polar regions above 60° N or below 60° S and during periods of significant solar activity.
4.3.2 SELCAL. SELCAL is a means to alert an individual aircraft that a ground station wishes to communicate with it. ATS providers can transmit SELCAL signals over very high frequencies (VHF) or HF. The signals produce an audio tone and possibly a cockpit light or message that alerts you to initiate contact with the appropriate ATC unit.
4.3.2.1 The SELCAL codes are controlled by a commercial service and are assigned to a specific aircraft. Since the number of unique SELCAL codes is less than the number of aircraft with SELCAL capability, multiple aircraft could be operating and logged in with the same SELCAL code assignment.
4.3.2.2 When you apply for SELCAL codes for your aircraft, the issuing company will deconflict duplicate codes by region as much as possible. However, aircraft flying in multiple regions may encounter another aircraft using the same code. You must ensure that the SELCAL contact you respond to is intended for your aircraft.
4.3.2.3 Efforts are underway to increase the number of codes by expanding the number of audible tones that make up the system. The newest SELCAL equipment will use alphanumeric instead of the alpha-only codes, increasing
Chapter 4. › 4.4 CPDLC and Automatic Dependent Surveillance-Contract (ADS-C).
the number of unique identifiers from the current 10,920 to 215,760. Implementation of the new system is expected to begin in the 2017 timeframe. Operators with HF SELCAL systems not compatible with the new alphanumeric codes may continue to encounter other aircraft with duplicate codes.
4.3.2.4 Check HF SELCAL even when your Controller-Pilot Data Link Communication (CPDLC) is working properly. You should do a SELCAL check prior to oceanic entry and then again at each control area (CTA) boundary.
4.3.3 Satellite Voice (SATVOICE). In keeping with ICAO’s recognition of SATVOICE as a valid long-range communication system (LRCS), the FAA accommodates SATVOICE through arrangements with the recognized Aeronautical Mobile Satellite Service (Route) (AMS(R)S) providers. Direct SATVOICE contact between the pilot and ATC is currently limited to distress and urgency situations, or other exceptional circumstances only. For oceanic communications service provider relay to ATC, SATVOICE short codes are published in the U.S. Aeronautical Information Publication (AIP). As this technology evolves, ensure that you comply with the latest authorizations. For additional guidance, refer to ICAO Document 10038, Satellite Voice Guidance Material.
4.3.4 Radio Frequency Changes. Radio frequencies are constantly changing. Thus, it is important that you consult the appropriate AIP, current oceanic charts, and commercial en route publications for the most current information.
• ICAO NAT Document 007 describes North Atlantic (NAT) operations, to include communication and navigation procedures in NAT airspace.
• Commercially published navigation charts contain details of communication procedures on inserted panels. Exercise some caution in using this reference, as they may be on a different update cycle than the source documents and therefore could be not completely up to date.
4.4 CPDLC and Automatic Dependent Surveillance-Contract (ADS-C). Since the mid-1990s, data link communications systems have enhanced contact between ATS providers and the flight deck. These communication systems are now widely used throughout the world and have also led to the implementation of Automatic Dependent Surveillance (ADS) systems that further improve ATS capability. CPDLC technology improves communications between aircraft and ATS providers. CPDLC eliminates the often challenging HF voice communications that were the only communication link with oceanic and remote continental airspace air traffic controllers for decades. With CPDLC, you and the controller transfer ATC clearance requests and instructions digitally, reducing the likelihood of miscommunication. ADS-C is also widely used in oceanic and remote continental airspace and, in combination with CPDLC, has become required equipment to be assigned the most efficient routes across the NAT organized track system (OTS), where ATC allows minimum separation between aircraft.
4.6 ATC in Oceanic and Remote Continental Airspace. › 4.6.1 Procedural Airspace.
Note 1: In ADS-C, C = “Contract.” The controller sets up one or more electronic contracts with your aircraft to automatically provide time-triggered (periodic) and/or condition-triggered (e.g., deviation event) reports.
Note 2: Equipage with CPDLC does not eliminate the requirement for operable two-way radios. For most oceanic operations this means operable HF radios are required.
4.4.1 Access to Preferred Airspace. Since equipment like CPDLC and ADS-C improves the efficiency with which aircraft in oceanic and remote continental airspace can be controlled, such better-equipped aircraft are being better served through initiatives to reserve preferred blocks of oceanic airspace for those aircraft. Preferred altitudes and routes around the world are more readily issued to aircraft equipped with robust communications, navigation, and surveillance capabilities.
4.4.2 Flight Management Computer Waypoint Reporting (FMC WPR) Service. FMC WPR service is one of the original data link capabilities, whereby your FMC sends a waypoint report to the ATS provider via Aircraft Communications Addressing and Reporting System (ACARS) or CPDLC. It is gradually being replaced by automatic position reporting via ADS-C systems.
4.5 Data Link Systems—Operational Authorization to Use. We will grant operational authorization for operators to use data link by issuing OpSpec/MSpec/LOA A056, Data Link Communications, as appropriate.
Note: OpSpec/MSpec/LOA A056 also applies to datalink communications in overland areas, such as Aeronautical Telecommunications Network Baseline 1 (ATN B1) (formerly Link 2000+), used in European airspace.
4.5.1 Procedures for Obtaining Authorization. You are required to obtain operational authorization prior to using data link systems on designated oceanic and remote continental airspace routes. You can find our guidance on the process and procedures for operational authorization and aircraft data link system approval in the current editions of the following documents:
• AC 20-140, Guidelines for Design Approval of Aircraft Data Link Communication Systems Supporting Air Traffic Services (ATS).
• AC 90-117, Data Link Communications.
4.5.2 Data Link Requirements and Standards. You can consult ICAO Document 10037, GOLD, for additional information on data link requirements and standards.
4.6 ATC in Oceanic and Remote Continental Airspace.
4.6.1 Procedural Airspace. Oceanic and remote continental airspace is nonradar (i.e., where the separation of aircraft does not depend on ground-based radar coverage) and where there is no other form of surveillance such as ADS-B. It is considered “procedural airspace.”
4.6 ATC in Oceanic and Remote Continental Airspace. › 4.6.4 Advanced Technologies and Oceanic Procedures (ATOP).
ATS providers in oceanic and remote continental airspace primarily provide procedural control and procedural separation to all flights.
4.6.1.1 These facilities issue clearances and instructions providing separation vertically and horizontally, based on the specific aircraft equipment authorizations you indicate on your flight plan. Because of ATC’s lower confidence in the aircraft’s reported position, adjacent aircraft under procedural control are kept farther apart from each other than under radar control.
4.6.1.2 ATC monitors your compliance with the issued clearance. Your aircraft position reports are processed for conformance with the clearance. If your aircraft is equipped with ADS-C, it provides trigger alerting for lateral and vertical deviations.
4.6.1.3 In order to make this nonradar airspace traffic management system work the way it is designed, you must provide timely and accurate time estimates (estimated time of arrival (ETA)) and operate with strict discipline and adherence to ATC clearances and procedures, both normal and contingency.
4.6.1.4 Controllers manage longitudinal separation in procedural airspace by assigning speeds, either true Mach number or true airspeed. An airspeed assignment is one element of an oceanic clearance. Proper separation of aircraft is dependent upon pilots maintaining the speed assigned with the oceanic clearance (not to be confused with the flight plan speed); therefore, compliance with the speed assignment is mandatory.
4.6.2 ICAO Procedures for Specific Geographical Areas. You will find detailed ICAO procedures for specific geographical areas in ICAO Document 7030, Regional Supplementary Procedures. FAA ATC bases its procedures for oceanic and remote continental airspace on ICAO Standard and Recommended Practices (SARP).
4.6.3 U.S. ATS in Oceanic and Remote Continental Airspace. The United States provides ATS in oceanic and remote continental airspace as follows:
• Atlantic Ocean: New York, Miami, and San Juan Flight Information Regions (FIR).
• Gulf of Mexico: Miami and Houston FIRs.
• Pacific Ocean: Oakland and Anchorage FIRs.
• Arctic Ocean: Anchorage Arctic FIR.
• Alaska Remote Continental Airspace: Anchorage Air Route Traffic Control Center (ARTCC).
4.6.4 Advanced Technologies and Oceanic Procedures (ATOP). U.S. controllers utilize the ATOP (also referred to as Ocean21) System in the airspace of Oakland Oceanic, New York Oceanic, and Anchorage Oceanic FIRs.
Chapter 4. › 4.8 Air Defense Identification Zones (ADIZ).
4.6.4.1 Within this airspace, ATOP identifies suitably equipped aircraft for the controller (such as CPDLC and ADS-C), provides decision support tools for establishing the separation minima for all pairs of aircraft along a cleared profile, and provides aircraft profile conformance monitoring and protection.
4.6.4.2 ATOP deciphers flight plan information to determine which separation standards may be applied to a particular aircraft based on filed aircraft equipage. The system is capable of determining separation standards which may be applied between aircraft with different equipage and speeds. You must notify ATC immediately if your communications, navigation, and surveillance equipment capability degrades below that which you listed in your flight plan.
4.6.4.3 ATOP protects random routes of an individual aircraft and can issue conflict warnings in excess of 2 hours ahead of the event, depending on local adaptation. ATOP can also adapt to the separation standards applied by adjacent ATC facilities and can warn the controller when a conflict will occur based on the adjacent ATC facility’s requirements. This allows controllers to effectively plan for transitions to adjacent FIRs.
4.6.4.4 You can find specific information regarding ATC separation standards in the current edition of FAA Order JO 7110.65, Air Traffic Control. Additionally, trial periods where new separation standards are being applied will be announced via FAA International Notices to Airmen (NOTAM).
4.7 Special Use Airspace (SUA).
4.7.1 Warning Area. A warning area is airspace of defined dimensions extending from 3 NM outward from the coast of the United States that contains activity that may be hazardous to nonparticipating aircraft. The purpose of such a warning area is to warn nonparticipating pilots of the potential danger. A warning area may be located over domestic or international waters or both.
4.7.2 Prohibited Areas. ICAO specifies that these areas exist “above the land areas or territorial waters of a State, within which the flight of aircraft is prohibited.”
4.7.3 Restricted Areas. ICAO specifies that these areas exist “above the land areas or territorial waters of a State, within which the flight of aircraft is restricted in accordance with certain specified conditions.”
Note: Carefully review charts for these types of areas when you plan your flight, taking note of the area operating times and restrictions. You should also review applicable oceanic NOTAMs.
4.8 Air Defense Identification Zones (ADIZ). Title 14 CFR part 99, Security Control of Air Traffic, discusses defense areas and ADIZ. You can check part 99, the latest U.S. AIP, the latest AIM (Chapter 5, Section 6), and all FAA NOTAMs Domestic/International to ensure compliance with national security requirements in the ADIZ.
4.9 World Geodetic System 1984 (WGS 84). › 4.9.1 Operations in Areas That Are Not WGS 84-Compliant.
10/4/16 AC 91-70B
4.9 World Geodetic System 1984 (WGS 84). ICAO and the United States endorse the WGS 84 or equivalent as the geodetic reference datum standard for air navigation latitude and longitude coordinates. WGS 84 was developed in response to the aviation community’s need for a common geodetic reference system and to standardize aeronautical surveys and related products. You should determine in advance whether any countries you intend to fly over or into are WGS 84-compliant. Information about WGS 84 compliance is often noted on plates used in terminal operations or on airfield diagrams. A State’s AIP generally notes compliance with WGS 84. Most areas of the world are listed as: 1) Unknown (U); 2) Partially Compliant (PC); 3) Compliant (C); or 4) Noncompliant (NC) with WGS 84.
Note: Commercial charting vendors also post information on their websites about specific countries and their compliance with WGS 84.
4.9.1 Operations in Areas That Are Not WGS 84-Compliant. Flight manuals often include a note for long-range navigation systems (LRNS) indicating that, for countries or terminal areas that are not WGS 84-compliant, the crew should deselect the use of Global Navigation Satellite Systems (GNSS). You should be familiar with your flight manual limitations when flying in countries or terminal areas that are not WGS 84-compliant.
5.2 Preparing an Itinerary. › 5.2.1 Itinerary Factors.
10/4/16 AC 91-70B
CHAPTER 5. FLIGHT PLANNING GUIDANCE FOR INTERNATIONAL AND
OCEANIC AND REMOTE CONTINENTAL AIRSPACE OPERATIONS
5.1 Lead Time Requirements.
5.1.1 Preparation. Your preparation for a successful international flight, whether you fly large or small aircraft, starts with adequate planning and training. The lead time required for planning varies depending on such things as experience, training, and currency, as well as specific country requirements, and could exceed 30 days. Dispatch/flight locator departments available to 14 CFR part 121 operators and large 14 CFR part 135 operators could reduce certain planning time requirements.
5.1.1.1 Remember that many countries have long lead times to process visas or other necessary paperwork to approve an international flight. Depending upon the country, it may take up to 6 weeks to obtain visas and/or overflight and landing permits.
5.1.1.2 Ensure you are aware of current and special notices relating to entry and overflight requirements for the countries on your itinerary. In most cases outside North America and Europe, you obtain prior permission to land in or overfly a country directly from that country’s Civil Aviation Authority (CAA). You can also find information on immunizations, ports of entry, and other important requirements in the country’s Aeronautical Information Publication (AIP) and in various commercial publications.
5.1.2 Verification. You need to allow enough lead time to ensure your planning is thorough, complete, and correct. Always cross-check and verify any flight planning products against the appropriate source documents. By doing so, you could uncover potential errors before they result in a pilot deviation.
5.2 Preparing an Itinerary.
5.2.1 Itinerary Factors. Preparing the itinerary is one of the most important aspects of your international flight. You may want to consider the following questions when developing your itinerary:
1. To which destinations do I intend to fly (or overfly)?
2. Via what routes and altitudes?
3. Are there any terrain clearance concerns along those routes at those altitudes?
4. Have I identified any concerns with suitable Equal Time Point (ETP) alternates along those routes and altitudes?
5. Are there any pitfalls I should be aware of from each State’s AIP?
6. What communications, navigation, and surveillance equipment and authorizations must I have in order to fly my intended routes and altitudes?
5.2 Preparing an Itinerary. › 5.2.2 Country-Specific Issues and Requirements.
10/4/16 AC 91-70B
7. Will I be operating in a Special Area of Operation (SAO)? Do I have the necessary operational authorization(s) to do so?
8. With regard to my Global Navigation Satellite System (GNSS) equipment, are there any World Geodetic System 1984 (WGS 84) compliance issues in countries I intend to transit? (Paragraph 4.9 provides information on WGS 84.)
9. What survival equipment must I have on board in order to fly my intended routes?
10. Are there suitable en route and destination alternates available in the event of an emergency diversion at other than my intended en route altitude? Are there terrain clearance or oxygen considerations at those divert altitudes?
11. Does my preferred destination have instrument approaches and arrival and departure procedures that are compatible with my aircraft equipment and authorizations?
12. What crew rest requirements will I have for each destination?
Note: See paragraph 5.3 below regarding fatigue management issues.
13. Do I intend to use a flight planning or dispatch service for my trip?
14. If my routes take me through oceanic airspace, have I reviewed the following:
• Oceanic error mitigation procedures?
• Oceanic flight planning, plotting charts, navigation, and waypoint procedures?
• My oceanic checklist?
• Strategic Lateral Offset Procedures (SLOP)?
• En route procedures for each airspace I will pass through?
• Oceanic contingency procedures?
15. Are there specific pilot certification, type rating, and/or medical certificate requirements for the countries I’ll be visiting? Are single-pilot operations authorized?
16. Will my intended route take me through areas of volcanic activity?
17. If my route takes me through polar areas, have I researched the unique risks inherent to operations on polar routes?
5.2.2 Country-Specific Issues and Requirements. As part of your itinerary preparation, asking the following additional questions can help you determine the country-specific issues/airspace requirements that might affect your international flight:
10/4/16 AC 91-70B
1. Do I require overflight and landing permits for any of the airspace/airfields I will transit?
2. How much will overflight and landing fees cost, and how do I pay for each airspace and destination I intend to transit (e.g., credit card, cash, local currency, U.S. currency)?
3. How much advance notification do I need to provide prior to arrival?
Note: All countries require some form of advance notification of arrival. You should carry a copy of the advance notification, as well as confirmation that the notification was sent. This is particularly important for countries that do not normally return approvals.
4. What are the availability, types, and duration of visas, tourist cards, and other required entry documents for all countries I intend to visit, as well as those with potential alternate airports (in the event I have to divert)?
Note: Some countries require that you have a visa for the next country of entry before departure, as well as proof of required immunizations for that country. You can obtain this information from the U.S. Department of State (DOS).
5. Are there prohibitions, restrictions, and/or applicable notices for countries I intend to visit?
Note: The FAA’s website includes a special section on prohibitions, restrictions, and notices applicable to foreign countries at http://www.faa.gov/air_traffic/publications/us_restrictions/. You should pay particularly close attention to this aspect of your flight planning.
6. What is the normal work week for countries I intend to overfly/enter?
Note: Understanding this will help you coordinate for visas and overflight/landing permits. You can obtain this information from the DOS.
7. Are there any import regulations I need to consider, given the amount of time I intend to remain in the countries on my route?
Note: Aircraft that remain within the territorial limits of a country for an extended period of time may become subject to import regulations and impoundment. Determine in advance the number of days that an aircraft may remain in any country where the aircraft will land.
8. What hours are customs, immigration, and other services operational?
9. Do I intend to conduct any operations that might be considered “cabotage?”
5.3 Crew Fatigue. › 5.3.5 Sleep Aids.
10/4/16 AC 91-70B
5.2.3 Airport-Specific Issues. Consider the following airport-specific issues when planning for your overseas trip:
1. What time considerations can affect your trip?
• What is local time at each of my destination airports in terms of Coordinated Universal Time (UTC)?
• What is local time at my original departure airport?
• Are there restrictions on operating at night in the countries I intend to transit?
• Do any of the airspaces/destinations I intend to transit require slot times?
2. Is a Prior Permission Only (PPO) number required for landing?
3. Do my preferred destination and alternate airfields have the appropriate grade of fuel and other types of aircraft handling services available?
4. Are maintenance services available at my destination airfields?
5. Should I bring spare parts for my aircraft?
6. Will I have lodging available at the destination?
5.3 Crew Fatigue.
5.3.1 Fatigue Management. International travel typically involves crossing time zones and interrupting normal sleep patterns (circadian rhythm). Ensure you have a plan for how you will manage fatigue for you and your crew.
5.3.2 Fatigue Management Strategies. The current edition of AC 120-100, Basics of Aviation Fatigue, discusses strategies to mitigate the effects of fatigue and is an excellent resource. The current edition of AC 120-103, Fatigue Risk Management Systems for Aviation Safety, discusses the Fatigue Risk Management Systems (FRMS) prescribed in 14 CFR part 117. While part 117 does not apply to all operators, we recommend you review both ACs as the contents cover issues that are important to all aircrews.
5.3.3 Self-Care and Time Zone Differences. Having a high level of physical fitness, using caffeine strategically, and avoiding alcohol can help you adjust to time zone differences, allow your body to rest better, and help make you a more effective, safer operator.
5.3.4 Preparing to Mitigate Fatigue. Inquire in advance about day sleeping or noise levels in the location where you intend to get your crew rest. This will help your crewmembers know what challenges to good rest might lie ahead. You should also consider adding one or more pilots beyond that for which the aircraft is certified for long-duration flights or those outside of normal sleep times. This will help mitigate fatigue issues and promote safer flying.
5.3.5 Sleep Aids. Make sure you understand the restrictions on using sleep aids and the importance of consulting an Aviation Medical Examiner (AME) prior to use. They will
5.4.1 Documentation. › 5.4.1.1 Aircraft/Aircrew Documentation.
advise you on the possible side effects of sleep aids. We have built a list of approved prescription sedative-hypnotic-type drugs that can be taken under certain conditions.
• Information regarding pharmaceutical sleep aids can be found on the FAA website.
• This site includes names of many popular sleep aids. It also includes the required wait time after taking the last dose before you can fly (“pill to push” time).
5.4 Required Paperwork/Documentation. Whenever you fly into, from, or over foreign territory, you must comply with that territory’s regulations. Ensure that you have all required entry documents available for presentation upon arrival; you may need to provide multiple copies of each.
5.4.1 Documentation. Local authorities may ask to see the below-listed types of paperwork. The Articles of the Chicago Convention specify those items marked with a double asterisk (**).
5.4.1.1 Aircraft/Aircrew Documentation. It is important to note that you may be responsible for additional documentation requirements that this list does not include.
1. Airworthiness certificate**.
2. Aircraft registration** (some States do not allow temporary certificates).
3. Radio station license**.
• International Civil Aviation Organization (ICAO) Annex 6 Part I requires that one member of the flightcrew hold a valid radio telephone operator’s license “authorizing operation of the type of radio transmitting equipment to be used.”
• The European Aviation Safety Agency (EASA) has published inspector guidance for its SAFA Ramp Inspections program that references the ICAO Annex 6 requirement.
• For U.S. domestic flights operating only on very high frequencies (VHF), the Federal Communications Commission (FCC) does not require the license.
4. Minimum equipment list (MEL) (or Master Minimum Equipment List (MMEL) if operator plans on operating under this option).
5. Airplane Flight Manual (AFM) with Weight and Balance (W&B) information and metric conversion tables, if applicable.
6. Copies of aircraft and engine logbooks.
7. Import papers for aircraft of foreign manufacture.
8. Operations specifications (OpSpecs)/management specifications (MSpecs)/Letters of Authorization (LOA).
5.4.1 Documentation. › 5.4.1.2 Trip-Specific Documentation.
10/4/16 AC 91-70B
Note: Some countries require an OpSpec/MSpec/LOA from the State of Registry or the State of the Operator before operating the aircraft in those countries.
9. Ownership papers.
10. Certificates of insurance, if applicable.
11. Authorization letters from the operating company or the aircraft owner (original signature required), if applicable.
Note: For privately owned aircraft where the owner is not on board, many countries require a letter from the owner before they will allow operations within their country (you can find specific information on this letter and other requirements in the AIP of the countries concerned).
12. Licenses.
13. Crewmember certificates**.
Note: Pay special attention to medical certificates, as expiration rules vary from country to country; consult the AIP for those countries where you intend to land.
5.4.1.2 Trip-Specific Documentation. The following information will change for each flight, but should be available for presentation to authorities:
1. Passenger manifest, containing complete names of passengers and places of embarkation and destinations of each**.
2. Cargo manifest and detailed declaration of the cargo, if carried**.
3. Copies of overflight and landing permissions.
4. General declarations.
5. Journey logbook, signed by the pilot in command (PIC)**. ICAO Annex 6 identifies the components of the journey logbook as listed below. Consult the AIP for the country you are visiting for their particular requirement.
• Airplane nationality and registration.
• Date.
• Names of crewmembers.
• Duty assignments of crewmembers.
• Place of departure.
• Place of arrival.
• Time of departure.
Chapter 5. › 5.6 Managing Risk in Oceanic and Remote Continental Airspace Operations.
• Time of arrival.
• Hours of flight.
• Nature of flight (private, aerial work, scheduled, or nonscheduled).
• Incidents and observations, if any.
• Signature of person in charge.
5.4.1.3 Personal Documentation for Crew and Passengers. When planning a trip to or from a foreign country, you must ensure all travelers have proper personal documentation (passports and visas, as required). You may find the requirements for individual countries at https://www.state.gov/travel.
5.5 Entry to Foreign Airspace—Flight Plan Versus Formal Advance Permission.
5.5.1 Permission for Airspace Entry. When the foreign Air Traffic Service (ATS) authority accepts your flight plan and issues you a flight clearance, you have not necessarily received official approval for entering that State’s airspace. The governing CAA may independently require permission for airspace entry, and your destination airfield may require permission as well.
5.5.2 Flight Plans. Your flight plan provides advance notice of foreign airspace penetration and facilitates effective air traffic control (ATC) procedures. For some countries, your flight plan is the only advance notice required; other countries use your flight plan as a check against previously granted permission to enter national airspace.
5.5.3 State AIPs. During your pretrip planning, as noted in paragraphs 5.1.1.2, 5.2.1, and 5.2.2 above, consult the AIP for the States you will transit to determine any overflight/landing permits and whether prior permission is required. Ensure you allow plenty of lead time to request and obtain all necessary permissions.
5.6 Managing Risk in Oceanic and Remote Continental Airspace Operations. Operators should have a risk management process before conducting oceanic operations (per ICAO Annex 19, issued in 2013). Many of the oceanic planning topics included in earlier portions of this chapter should be included as elements of your oceanic operations risk assessment. Examples include the list of topics immediately below. Operators are strongly encouraged to research the information available on the FAA website, both from the standpoint of oceanic operations planning, and risk management overall. Non airline operators are also encouraged to review the material specifically earmarked for airline operators. You can get a lot of good ideas from that information.
• Communications, navigation, and surveillance requirements for airspace.
• Crew knowledge and recency-of-experience.
• Crew fatigue.
• Airspace Search and Rescue (SAR) options.
5.7 Weather Forecasts and Other Meteorological Planning. › 5.7.4 Enhanced Weather Information Systems (EWINS).
10/4/16 AC 91-70B
• Weather and atmospheric conditions unique to the airspace.
• Applicable survival equipment.
• Alternate airports.
• Contingency procedures.
Note: The Automated Mutual-assistance Vessel Rescue (AMVER) system, sponsored by the U.S. Coast Guard (USCG), is a computer-based voluntary global ship reporting system used worldwide by SAR authorities to arrange for assistance to persons in distress at sea. Operators conducting oceanic operations are encouraged to be familiar with AMVER in case of a potential ditching. Once the operator notifies ATC of a possible ditching, all merchant vessels registered with AMVER and within 100 nautical miles (NM) of the aircraft’s predicted ditching position will be notified.
5.7 Weather Forecasts and Other Meteorological Planning.
5.7.1 The National Weather Service (NWS). The NWS provides weather, hydrologic, and climate forecasts and warnings for the United States, its territories, adjacent waters, and ocean areas. If you operate outside of the jurisdiction of the NWS, you must utilize a weather source approved by the Administrator.
5.7.2 International Weather Services. You can access many different international weather sources through the NWS. While the NWS may recognize these sources, they are not necessarily approved by the NWS and may not meet regulatory requirements. As a certificate holder, you must have your international weather sources approved in your OpSpec/MSpecs.
5.7.3 Recognized Weather Services. As representatives of the Administrator, Principal Operations Inspectors (POI) may approve the following sources:
• The NWS for the United States and its territories located outside of the 48 contiguous states.
• U.S. and North Atlantic Treaty Organization (NATO) military observing sources.
• Meteorological offices operated by ICAO Member States.
• ICAO Member-State-authorized meteorological stations or automated observations.
• Members of the World Meteorological Organization (WMO).
5.7.4 Enhanced Weather Information Systems (EWINS). Many commercial operators utilize an EWINS. EWINS are systems for gathering, evaluating, and disseminating aviation weather information, and for issuing weather reports and forecasts prepared by properly trained and qualified aviation meteorologists or aircraft dispatchers. Air carriers use EWINS which are proprietary to each carrier. Air carriers require FAA approval to use EWINS.
Chapter 5. › 5.10 Polar Operations.
5.7.4.1 Each carrier’s EWINS must have sufficient procedures, personnel, and communications and data processing equipment to effectively obtain, analyze, and disseminate aeronautical weather data. An EWINS source may produce weather analyses and forecasts based on meteorological observations provided by the Federal government.
5.7.4.2 For an explanation of EWINS, refer to the current edition of AC 00-45, Aviation Weather Services. Approval to use EWINS weather products is issued on a case-by-case basis and is currently only applicable to 14 CFR part 91 subpart K (part 91K) program managers and part 121 or 135 certificate holders, who may either act as their own EWINS or contract for services from an outside source. These approved operators may conduct flight operations using the weather analyses and forecasts produced by their approved EWINS.
5.8 Notices to Airmen (NOTAM). We publish these NOTAMs on a 28-day cycle. They include significant international information and special notices that could affect your decision to enter or use certain areas of foreign or international airspace. If you are seeking to enter areas of the world that require special considerations, these NOTAMs can be very important. To access the two most recent editions of the domestic/international FAA NOTAMs, refer to www.faa.gov/air_traffic/publications/notices/.
5.9 Extended Operations (ETOPS). ETOPS (the ICAO term is Extended Diversion Time Operations (EDTO)) requirements pertain to aircraft operated under parts 121 and 135. ETOPS is a system of maintenance, planning, alternate airport selection, dispatch, and flight operations standards that are designed to preclude a diversion and, if one were to occur, to protect that diversion. Thus, ETOPS standards establish a higher level of performance requirements and equipment monitoring.
Note: Rules covering ETOPS do not address operations conducted under part 91. However, because risk increases with distance from an adequate airport, if you are a General Aviation (GA) operator, we strongly recommend that your pilot training, maintenance practices, flight planning, and any applicable dispatch procedures follow the processes and procedures established in ETOPS regulations and guidance.
5.9.1 ETOPS Guidance. Guidance pertaining to ETOPS is provided in the current editions of AC 120-42, Extended Operations (ETOPS and Polar Operations), and AC 135-42, Extended Operations (ETOPS) and Operations in the North Polar Area. The regulatory basis for ETOPS requirements is provided by part 121, §§ 121.161 and 121.374 and appendix P, and part 135, § 135.364 and appendix G.
5.10 Polar Operations. ACs 120-42 and 135-42 cover polar operations by aircraft operated under parts 121 and 135 respectively. As noted in the ETOPS discussion above, we strongly recommend part 91 operators refer to these ACs if you intend to attempt a flight via a polar route. Other worthwhile sources of information include the Canada and Iceland AIPs and the Canadian Designated Airspace Handbook. The North Polar Area of
5.12 Rotorcraft Operations. › 5.12.1 FAA and ICAO Requirements.
Operations includes the area that lies north of latitude 78° N. The North Polar routes across Russia are shown in the Russian AIP or in commercial charting publications for Eastern Europe and Eurasia. The South Polar Area of Operations includes the area south of latitude 60° S. Operators should contact an SAO specialist for advice on things to consider when planning polar operations.
1. OpSpec/MSpec B055, North Polar Operations, authorizes North Polar operations. OpSpec/MSpec B040, Operations in Areas of Magnetic Unreliability, authorizes operations in areas of magnetic unreliability (AMU).
2. Operations in AMUs are not authorized when using a Global Positioning System (GPS)-only navigation-sensor flight management system (FMS). This is due to the lack of accurate and reliable heading information from flux valve-derived headings.
5.11 Areas with Limited ATS. While part 91 GA operators are not bound by the requirements below, we recommend that they have a solid understanding of this information before attempting to operate in this type of airspace. If you intend to operate in advisory-only airspace, your training programs and operating procedures must allow for safe operations and ensure compliance with the expected operating practices. Commercial operators must also show that they comply with OpSpec/MSpec A014, Special En Route IFR Operations in Class G Airspace. If you intend to operate in uncontrolled information regions, you will not have access to ATC, air traffic advisory (TA), flight information, and alerting services. When operating within these areas, you must have acceptable, alternative means to ensure the following:
1. You can notify the appropriate organization in a timely manner should you require SAR assistance.
2. You have a method to access changes in Significant Weather (SIGWX) information in a timely manner.
3. Those navigation facilities necessary for you to safely conduct the operation are available and serviceable. You can receive updates regarding the serviceability of the required Navigational Aids (NAVAID).
4. You have reliable in-flight information concerning other instrument flight rules (IFR) aircraft operating near your route of flight (e.g., Traffic Alert and Collision Avoidance System (TCAS) and/or Automatic Dependent Surveillance-Broadcast (ADS-B) In). This could also include “broadcast in the blind” procedures and other “expected” practices (see Appendix E, IATA In-Flight Broadcast Procedure, as well as ICAO Annex 11’s description of traffic information broadcasts by aircraft (TIBA)).
5.12 Rotorcraft Operations.
5.12.1 FAA and ICAO Requirements. The basic part 91 guidance outlined earlier in this chapter also applies to helicopter operations in oceanic and remote continental airspace. If you are operating in international airspace or another State’s airspace, you are still obligated
5.12.4 Navigation Requirements. › 5.12.4.2 For part 135 operators, all the navigation equipment that you…
under part 91, § 91.703 to follow ICAO Annex 2. The § 91.703 requirement to follow the rules of the countries you overfly and those in which you intend to land also applies. If the part of 14 CFR under which you operate conflicts with the rules of the country you are operating over or in, you must follow the rules of that country.
5.12.2 Offshore Helicopter Operations in the U.S. National Airspace. The current edition of AC 90-80 contains detailed information on offshore helicopter operations in the U.S. National Airspace System (NAS), both instrument and radar. It also provides instruction on how you can gain authorization to conduct such operations.
5.12.3 Offshore Operators. If you are an offshore operator, you are required to obtain OpSpec/LOA H104, Helicopter Offshore Instrument Operations: Offshore Standard Approach Procedure (OSAP), Airborne Radar Approach (ARA), and Helicopter En Route Descent Area (HEDA) Operations, if conducting en route descent procedures under IFR operations. You will receive the OpSpec or LOA, as applicable, once you meet all certification requirements.
5.12.4 Navigation Requirements. You must meet the following navigation requirements in order to operate rotorcraft in oceanic and remote continental airspace.
5.12.4.1 You may develop proposed routes using NAVAIDs where you have adequate signal coverage available. In areas where signal coverage is not available, you must provide a suitable means of navigation. We may require a validation test in visual flight rules (VFR) conditions to ensure that you are able to demonstrate adequate navigational performance for the route(s) before granting approval for your use of the route(s).
5.12.4.2 For part 135 operators, all the navigation equipment that you use in extended overwater or IFR operations must meet § 135.165(b) requirements. If you obtain positive course guidance for any portion of the route through the use of long-range navigation equipment, such as GPS meeting FAA Technical Standard Order (TSO)-C145, TSO-C146, or TSO-C196, you will not receive approval for these operations until your aircraft has two independent receivers for navigation installed and operative (only one is required in the West Atlantic, Caribbean, and Gulf of Mexico).
6.1.2.2 A large height deviation (LHD) occurs when an aircraft is 300… › 6.1.2.2.2 Collected data indicates that a majority of crew-related…
10/4/16 AC 91-70B
CHAPTER 6. FLIGHT EXECUTION GUIDANCE FOR OPERATIONS IN OCEANIC
AND REMOTE CONTINENTAL AIRSPACE
6.1 General Information.
6.1.1 Checklists. In Appendix D, Sample Oceanic Checklist, we have included a sample oceanic checklist tailored from the International Civil Aviation Organization (ICAO) version, in both condensed and expanded forms. The checklist is designed to encourage an orderly task flow and reduce oceanic vertical, lateral, longitudinal, and timing navigation errors.
Note: You may tailor the expanded checklist to your specific needs and approvals. During actual operations, refer to that tailored expanded checklist to ensure you follow the procedures in their entirety.
6.1.2 Pilot Deviations—Common Causes.
6.1.2.1 Technological advances in communications, navigation, and surveillance equipment have enabled aircraft to operate with ever-improving precision and accuracy. However, despite this increased navigational capability, pilots continue to deviate from their current route clearances.
6.1.2.2 A large height deviation (LHD) occurs when an aircraft is 300 feet or more off its assigned altitude. LHDs increase the risk of mid-air collision.
6.1.2.2.1 The most common causes of LHDs are:
1. Air traffic control (ATC) loop errors:
• Misunderstood clearances.
• Lack of proper ATC coordination procedures.
2. Pilot deviations from assigned altitude:
• Following the flight plan rather than a clearance or reclearance.
• Erroneous altitude programming in the flight management system (FMS), such as a mistake in the step-climb entry.
• Misinterpretation/misapplication of conditional clearances.
• Improper execution of pilot contingency procedures.
• Turbulence encounters.
6.1.2.2.2 Collected data indicates that a majority of crew-related errors involve misinterpretation or misapplication of “conditional clearances.” Conditional clearances improve the efficient utilization of airspace, allowing ATC to assign altitudes that enable lower fuel burn. Event reports from ATC and flightcrews indicate that pilots misapply terms in the clearance such as “BY”
6.1.2.2 A large height deviation (LHD) occurs when an aircraft is 300… › 6.1.2.2.3 Your training program should provide you and your crew with…
or “AT”—terms, which have completely different meanings. See Table 6-1 below for examples of incorrectly applied conditional clearances.
Table 6-1. Examples of Incorrectly Applied Conditional Clearances
CLEARANCE CREW ACTION CORRECT ACTION
Via CPDLC at 1714, crew conditionally cleared, “maintain F340, at 1725 climb to and maintain F360, climb to reach F360 by 1735, report level, due to traffic.”
Crew initiated climb early, reported (ADS-C) passing F354 at 1721.
Crew should have delayed commencing climb until 1725, and planned to reach F360 by 1735.
Via CPDLC, crew cleared 66/30 66/40 65/50 F380 M081, cleared F390 to cross 66/40 level.
Crew commenced climb to F390 at 40W (Mode C).
Crew should have initiated climb prior to 40W in order to cross 40W at F390.
Via CPDLC at 1945, crew cleared maintain F330, at 1952 climb to and maintain F350, climb to reach F350 by 1957, report level F350.
Reported (ADS-C) level at F350 at 1948.
Crew should have delayed commencing climb until 1952, and planned to reach F350 by 1957.
Crew cleared 68/40 64/50 IRBIM F360 M083 via HF voice, crew recleared to descend after passing 65N to be level F340 before 64N.
Crew commenced descent at 6529N/4650W. Crew should have initiated descent after passing 65N and levelled at F340 prior to 64N.
Crew cleared 66/30 65/40 63/50 IRBIM LOMTA F400 M081. Via CPDLC, crew cleared climb F410 to cross 65/40 level.
Crew failed to climb as cleared and crossed 65/40 at F400 (ADS-C).
Crew should have initiated climb prior to 65N in order to cross 65N at F410.
6.1.2.2.3 Your training program should provide you and your crew with procedures that ensure all ATC clearances are complied with correctly, particularly clearances with en route restrictions such as changing flight levels (FL) based on a coordinated time or a specific geographic position.
Note: Per ICAO NAT Document 007, when flying in North Atlantic (NAT) airspace, you must immediately report to ATC when leaving and reaching a new FL. Doing so can enable the controller to identify and intervene when you have misunderstood or misapplied your conditional clearance.
6.1.2.4 Longitudinal errors, in the form of failure to provide updated… › 6.1.2.4.3 When position reports are made by voice, ICAO requires you to…
6.1.2.3 ICAO identifies gross navigation errors (GNE) as lateral deviations from course of 25 nautical miles (NM) or greater. In the NAT, the threshold is 10 NM.
6.1.2.3.1 The majority of today’s GNEs arise from pilots flying a very precise track to the wrong position because they failed to properly update their FMS to reflect their currently effective route clearance. This can also result from a clearance or reclearance that was incorrectly entered, misread, or misunderstood. Procedures to follow in the event of a reclearance are included in paragraph 6.4.1.6. Examples of scenarios that have led to GNEs are:
1. Poor management of the master document, resulting in crews not knowing the currently effective route clearance.
2. Incorrect waypoint entry procedures, particularly if the waypoints are not named and flightcrews must enter the full latitude and longitude.
Note: Waypoints entered via full latitude and longitude can produce misleading display names, where minutes are truncated or rounded and/or generic names are generated.
6.1.2.3.2 GNEs also result when the aircraft navigation mode is actually different from that assumed by the crew. This scenario typically occurs when the crew fails to return to lateral navigation (LNAV) after utilizing “heading select” to maneuver the aircraft.
6.1.2.3.3 Although there are a number of causes of GNEs, pilot inattention has been the root cause of many navigational errors. ICAO NAT Document 007, Chapter 14, Guarding Against Common Errors, provides excellent lessons learned from evaluation of GNE incidents.
6.1.2.4 Longitudinal errors, in the form of failure to provide updated estimated times of arrival (ETA), are another common navigation error and one that is easily preventable.
6.1.2.4.1 Deviations around weather can affect ETAs. It is important to remember that even when ATC clears you to deviate, the onus is on the pilot to update the ETA as appropriate.
6.1.2.4.2 You must adhere to your assigned (true) Mach number. If you use Long Range Cruise or Economy (ECON) modes to travel in speed-controlled airspace, you are operating in a constantly changing speed mode. Flying in these modes may not be compatible with the strict tolerances required for ATC’s longitudinal separation of aircraft.
6.1.2.4.3 When position reports are made by voice, ICAO requires you to report to Air Traffic Service (ATS) authorities any change to your ETA in excess of
6.2.1 ATC Flight Plan. › 6.2.1.2 Proper completion of an ATC flight plan requires that you have…
10/4/16 AC 91-70B
2 minutes, both for your initial oceanic entry point as well as all required reporting points along your route of flight through oceanic and remote continental airspace.
6.1.2.4.4 Discrepant wind data can result in inaccurate ETA computations. This can be particularly problematic if you are not flying at the flight-planned altitude or have outdated winds loaded in your FMS. You must diligently monitor your ETA and maintain your assigned Mach number in order to minimize these errors.
6.1.2.4.5 FMS-computed ETAs, particularly for more distant waypoints, may be erroneous due to down track wind conditions, which the FMS is not presently using to compute the ETA. You should compare FMS estimates with the ETA calculated on the operational flight plan prior to reporting the ETA to ATC facilities.
6.1.2.4.6 Automatic position reports delivered via Automatic Dependent Surveillance-Contract (ADS-C) have greatly reduced the occurrence of longitudinal errors caused by inaccurate ETAs. ATC establishes an ADS-C periodic report interval appropriate for the longitudinal and lateral separation criteria being used. More frequent reports compensate for wind discrepancies and provide ATC with accurate ETAs.
6.2 Flight Plan.
6.2.1 ATC Flight Plan.
6.2.1.1 ICAO requires a flight plan for all flights that cross international borders. Instrument flight rules (IFR) operations in oceanic airspace generally start at 6,000 feet. Visual flight rules (VFR) operations at or below 5,500 feet must comply with all applicable regulations and foreign airspace requirements.
6.2.1.1.1 Even though you may legally conduct flights in oceanic and remote continental airspace under VFR, there is generally a good likelihood of encountering instrument meteorological conditions (IMC) at some point in your flight.
6.2.1.1.2 We highly recommend that you file an IFR flight plan on any oceanic flight, if you are instrument rated and your aircraft meets the equipment requirements for IFR flight.
6.2.1.2 Proper completion of an ATC flight plan requires that you have detailed knowledge of the airspace you intend to transit, the airspace equipment requirements, and the required FAA authorizations (operations specifications (OpSpecs)/management specifications (MSpecs)/Letters of Authorization (LOA)). You also need to be thoroughly familiar with the equipment your aircraft has on board as listed in your filed flight plan. When you file, your flight plan is transmitted to ATS facilities along the route of flight. If you do
6.2.2 Equipment Capability Codes—Flight Plan. › 6.2.2.2 Upon entering oceanic and remote continental airspace, the RNP…
not file correctly, you could possibly experience delays before takeoff for an issue with an ATS authority along your route of flight.
6.2.1.2.1 The Aeronautical Information Manual (AIM) has a step-by-step description in Chapter 5 detailing how to complete FAA Form 7233-4, Pre-Flight Checklist and International Flight Plan.
6.2.1.3 As Performance-based Navigation (PBN) becomes more prevalent worldwide, ATS authorities will increasingly set aside certain airspace for PBN-compliant aircraft. You list your aircraft and crew capabilities using descriptors in items 10A, 10B, and 18 of the flight plan.
Note: Without the proper codes or remarks identifying the operational approvals of your crew and aircraft, controllers may deny you en route climbs to your most fuel-efficient FLs or access to the optimum routings or, in some cases, reject your flight plan entirely.
6.2.1.4 Title 14 CFR part 121 dispatch services are required to have staff knowledgeable in all filing requirements for both domestic and international operations. These services can support flight plan reroutes that may arise due to weather or congestion along your route of flight. If you are operating without the benefit of a dispatch service, you must have the knowledge and necessary tools available to react to unplanned reroutes, equipment failures, or emergencies that may impact your flight while en route.
6.2.2 Equipment Capability Codes—Flight Plan.
6.2.2.1 PBN is changing the way ATS providers apply separation criteria between aircraft. Without notifying the crew of either aircraft involved, ATS providers in “mixed mandate” airspace can reduce separation between aircraft based on your stated capability. In order to take advantage of opportunities for more efficient routings, your flight plan should reflect the lowest Required Navigation Performance (RNP) value for which you are capable and authorized.
6.2.2.2 Upon entering oceanic and remote continental airspace, the RNP setting in your flight management computer (FMC) must be equal to or less than that required for the route of flight, and it should reflect the RNP capability indicated on your flight plan. If you indicate RNP 4 capability on the flight plan, for example, ATC could establish separation criteria for your flight based on RNP 4 capability, even though only RNP 10 is required for the route of flight. Likewise, if RNP 10 is required for the route, the FMC setting must be no higher than 10.0. A higher setting will prevent your navigation system’s RNP performance monitoring and alerting capability, as well as the lateral deviation scaling, from functioning according to the RNP requirements for your route of flight. In such a scenario, a loss of required aircraft separation could ensue. The Area Navigation (RNAV)/RNP capability indicated on your
6.3.1 Preflight—Necessary Documents. › 6.3.1.9 Receiver autonomous integrity monitoring (RAIM) and fault…
flight plan must not be less than that for which you have been approved via an OpSpec, MSpec, or LOA.
6.2.2.3 If you are no longer able to meet your RNP navigation specification while en route (i.e., your Actual Navigation Performance (ANP) exceeds your RNP or required equipment has failed), you are required to immediately notify your ATS provider so they can adjust separation standards between you and other nearby aircraft as required.
6.3 Aircraft Preflight Guidance.
6.3.1 Preflight—Necessary Documents. Effective oceanic and remote continental airspace flight planning and execution requires a number of important pieces of information. You should ensure you have easy access to each of the following documents in the cockpit, as well as others that may be pertinent to your flight:
6.3.1.1 Master flight plan (“master document”).
Note: Use strict procedures to manage the master document. Maintain only one copy of the master document in the cockpit.
6.3.1.2 Notices to Airmen (NOTAM) for departure, destination, alternate(s), Extended Operations (ETOPS) alternates (as applicable), and oceanic flight information regions (FIR).
6.3.1.3 Global Positioning System (GPS) NOTAMs (as applicable).
6.3.1.4 Weather for departure, destination, alternate airports along the route of flight, and ETOPS alternates (as applicable).
6.3.1.5 Significant Weather (SIGWX) chart.
6.3.1.6 Wind charts for planned altitudes and altitudes after driftdown/emergency descent.
Note: Compute Equal Time Points (ETP) for contingencies, such as medical divert, engine loss, rapid decompression (RD), and a simultaneous RD and engine loss. Note the location of the ETPs on your chart.
6.3.1.7 Volcanic ash and solar flare information (as applicable).
6.3.1.8 Pilot Weather Reports (PIREP).
6.3.1.9 Receiver autonomous integrity monitoring (RAIM) and fault detection and exclusion (FDE) prediction tools (as applicable), available at http://sapt.faa.gov/default.php.
6.3.2 Cockpit Preparations. › 6.3.2.1 Check your maintenance log to ensure all your required…
6.3.1.10 Current track message (for any operations in airspace with a flexible organized track system (OTS)).
Note: If you have a track message or other separate route document associated with the flight, verify that the effective time of the message corresponds to your flight and that the designated route agrees with both your filed routing and the waypoint routing on your master document.
6.3.1.11 Plotting/orientation chart.
6.3.1.11.1 You should use a chart, of appropriate scale, to provide yourself with a visual presentation of your intended route, regardless of your type(s) of long-range navigation system (LRNS). Plotting your route on your chart will increase your situational awareness as you execute your trip through oceanic and remote continental airspace.
6.3.1.11.2 Your chart should include, at a minimum:
1. The route of your filed flight plan or currently effective route clearance.
2. Clearly depicted waypoints using standardized symbology.
3. Graphic depictions of all ETPs.
4. Alternate airports.
5. Proximity of other adjacent tracks.
Note: For certificated operators, if OpSpec/MSpec A061 has been issued authorizing use of an Electronic Flight Bag (EFB) and the principal inspector (PI) has authorized “interactive plotting for oceanic and remote continental navigation,” the EFB application may be used in place of a paper plotting/orientation chart. The current edition of AC 120-76, Authorization for Use of Electronic Flight Bags, provides guidance for operators to develop associated EFB procedures. For part 91 operators, an EFB may be used, provided the criteria and considerations of the current edition of AC 91-78, Use of Class 1 or Class 2 Electronic Flight Bag (EFB), are observed.
6.3.2 Cockpit Preparations.
6.3.2.1 Check your maintenance log to ensure all your required communications, navigation, and surveillance and altimetry equipment is operational in order to enter oceanic and remote continental airspace.
6.3.2 Cockpit Preparations. › 6.3.2.5 Two pilots should independently coordinate the loading and…
10/4/16 AC 91-70B
1. If you are faced with faulty aircraft equipment, such as your long-range navigation equipment or a central air-data computer fault, notify ATC as soon as possible. ATC will more than likely increase spacing around an aircraft with degraded capabilities.
2. Consult your minimum equipment list (MEL) to resolve malfunctioning equipment before you depart. A departure delay for maintenance may be warranted or a reroute to avoid oceanic airspace may be necessary.
6.3.2.2 Identify a single master clock in the cockpit.
1. You must verify that your onboard primary time source, or master clock, is set to Coordinated Universal Time (UTC). In most cases, this time source is the FMS.
2. Use master clock times for all ETAs and actual times of arrival (ATA).
6.3.2.3 Align your inertial navigation system (INS)/inertial reference system (IRS).
1. Proper INS/IRS loading and operating procedures are another important aspect to help you avoid navigation errors. Ensure you select navigation (NAV) mode at the appropriate time and properly manage your navigation computer during intermediate stops.
2. Follow your flight manual procedures carefully to ensure proper navigation reliability.
6.3.2.4 Have a second pilot independently verify the aircraft present position coordinates you have loaded in your navigation system.
1. Regardless of your type of LRNS or the method of insertion, you must verify your current ramp position in the LRNS against current aeronautical publications and not solely based on the present position remaining in the system from your last shutdown.
2. If you conduct another present position check on taxi out and it shows a gross difference with your gate coordinates, it could indicate a problem with the LRNS.
Continue reading ↓ 120 of 280 passages shown