Radar Vectors
Advisory Circular Cancelled Issued Aug 12, 2010 AFS-400 197 pages Copy saved Nov 18, 2026

AC 91-70A Oceanic and International Operations

This advisory circular (AC) contains general information and guidance for operators planning oceanic flights, including authorizations needed for operations outside the continental United States. This includes Special Areas of Operation (SAO) such as North Atlantic Minimum Navigation Performance Specifications (NAT/MNPS), Reduced Vertical Separation Minimum (RVSM), Area Navigation (RNAV), and Required Navigation Performance (RNP) airspace. a. Initiatives. In all geographic regions, the evolution of communication, navigation, surveillance and air traffic management (CNS/ATM) is the catalyst for initiatives such as data link, RNP, RNAV, Automatic Dependent Surveillance (ADS), and RVSM. b. Critical Areas and Procedures. The Federal Aviation Administration (FAA) identifies critical areas and procedures such as Strategic Lateral Offset Procedures (SLOP). c. Revisions. The dynamics of oceanic operations are such that they are constantly evolving and it is incumbent on the operators to closely monitor any changes. The FAA revised this AC to point the reader to the most current sources of international material. In many cases, the references are to a Web site. The material, however, is still found at www.faa.gov or by calling an FAA navigation specialist. This AC includes specific guidance for authorizations and other FAA policy issues. A detailed study of the FAA Web site is the best source for introduction information about oceanic, international, and remote operations.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

FOREWORD › This advisory circular (AC) contains general information and guidance…

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Oceanic and International

Operations

Date: 8/12/10 Initiated by: AFS-400

AC No: 91-70A Change:

FOREWORD

This advisory circular (AC) contains general information and guidance for operators planning oceanic flights, including authorizations needed for operations outside the continental United States. This includes Special Areas of Operation (SAO) such as North Atlantic Minimum Navigation Performance Specifications (NAT/MNPS), Reduced Vertical Separation Minimum (RVSM), Area Navigation (RNAV), and Required Navigation Performance (RNP) airspace. The dynamics of oceanic operations are such that they are constantly evolving and it is incumbent on the operators to closely monitor any changes. The Federal Aviation Administration (FAA) revised this AC to point the reader to the most current sources of international material. In many cases, the references are to a Web site. The material, however, is still found at www.faa.gov or calling a Federal Aviation Administration (FAA) navigation specialist. This AC includes specific guidance for authorizations and other FAA policy issues. A detailed study of the FAA Web site is the best source for introduction information about oceanic, international, and remote operations.

John M. Allen Director, Flight Standards Service

CONTENTS

Paragraph Page

CHAPTER 1. GENERAL

1-1. Purpose … 1 1-2. Cancellation … 1 1-3. Applicability … 1 1-4. Related CFR Regulations (current editions) … 1 1-5. Background … 2 1-6. General Information … 2

CHAPTER 2. UNITED STATES AVIATION AND THE ICAO

CONTENTS

2-1. Background … 5 2-2. ICAO and the ICAO Annexes … 5 2-3. U. S. Public Law, International Agreements, and Standards Related to Air Navigation … 9

CHAPTER 3. OCEANIC, INTERNATIONAL, AND REMOTE OPERATIONS

3-1. Introduction … 11 3-2. Equipment … 18 3-3. ATC … 22 3-4. Oceanic Communications … 26 3-5. Navigation Procedures (Navigation Sensors—Inertial Navigation System (INS), Inertial Reference Systems (IRS), or GNSS) … 27 3-6. Position Plotting … 28 3-7. Oceanic Operations … 38 3-8. Extended Operations (ETOPS) … 38 3-9. Strategic Lateral Offsets in Oceanic Airspace to Mitigate Collision Risk and Wake Turbulence … 39 3-10. Oceanic Emergency Procedures … 40 3-11. Communication, Navigation, Surveillance, and Air Traffic Management (CNS/ATM) Technology … 44 Figure 1. Data Link Diagram … 45 3-12. Monitoring of Performance-Based Navigation (PBN) and Communication … 46

CHAPTER 4. ATLANTIC, CANADA, AND EUROPEAN OPERATIONS

4-1. Atlantic Region … 49 4-2. Communications … 50 4-3. Navigation … 50 4-4. Surveillance—Canadian Control Areas … 51 Figure 2. Canada—Northern, Southern and Arctic Control Areas … 51 4-5. European Region … 52

Page ii

Page iii

CONTENTS (continued)

Paragraph Page

CHAPTER 5. NORTH PACIFIC OCEANIC OPERATIONS

CONTENTS (continued)

5-1. Introduction … 55 5-2. Communications … 55 5-3. Navigation … 57 5-4. Surveillance … 58 Figure 3. Pacific Organized Track System Routes … 59 Figure 4. North Pacific Routes … 60 5-5. Class II Navigation and Position Planning … 61

CHAPTER 6. SOUTHERN PACIFIC OCEANIC OPERATIONS

6-1. Introduciton … 63 6-2. Communications … 63 6-3. In-Flight Contingencies … 64

CHAPTER 7. WATRS/CARIBBEAN OPERATIONS

7-1. General … 65 7-2. Operational Policy and Procedures … 65 7-3. Navigation … 70 Figure 5. West Atlantic Route System Plus Oceanic Airspace … 76

CHAPTER 8. SOUTH AMERICA AND THE CARIBBEAN

8-1. Introduction … 77 8-2. Navigation … 77 8-3. Communications … 77 Figure 6. In-Flight Broadcast Procedures Over Intertropical Convergence Zone … 79 8-4. Collision Avoidance … 82 8-5. Dispatch … 82 Figure 7. Aircraft Communications Addressing and Reporting System Gap … 82 8-6. Maintenance/Dispatch Criteria … 83 8-7. Emergency Procedures and Diversions … 83 8-8. Medical Diversion … 85 8-9. Depressurization Procedures … 86 8-10. Safety of Flight … 86 Figure 8. Terrain Critical Areas … 86 8-11. Central America and Caribbean Weather … 88 8-12. South America Weather Information … 92 8-13. Communication … 96 8-14. Navigation … 96 8-15. Surveillance … 96

CONTENTS (continued)

Paragraph Page

8-16. CAR-SAM Routes … 97 Figure 9. Miami to Sao Paulo … 97

CHAPTER 9. GULF OF MEXICO OPERATIONS

9-1 Introduction … 105 9-2. Characteristics of the Airspace … 105 9-3. Navigation and Communications in the Gulf of Mexico … 107 9-4. International Operations … 109 9-5. Military and Helicopter Operations … 110

CHAPTER 10. LONG RANGE NAVIGATION

10-1. General Navigation Concepts, FAA Policies, and Guidance … 111 10-2. IRS/INS and Long-Range Navigation Procedures … 116 10-3. LRNS Problems and Recommended Actions … 121 10-4. Proving Tests and Validation Flights … 124 10-5. INS Navigation—Special Practices and Procedures … 126 10-6. FAA Approval of Global Positioning System (GPS) Equipment and Operations ....127 Figure 10. GPS Equipment Classes … 129

CHAPTER 11. HELICOPTER OCEANIC OPERATIONS

11-1. Gulf of Mexico … 135 11-2. IFR Offshore Operations … 135 11-3. Navigation Requirements and Procedures … 136

CHAPTER 12. CREW TRAINING FOR OCEANIC OPERATIONS

12-1. Crew Qualifications … 139 12-2. Pilot as PIC … 139 12-3. Training Considerations … 140

CHAPTER 13. GENERAL AVIATION SHORT-RANGE AIRCRAFT OCEANIC

OPERATIONS

13-1. Introduction … 143 13-2. ICAO Guidance … 143 13-3. The NAT Environment … 143

Page iv

CONTENTS (continued)

Paragraph Page

13-4. Pilot Qualification Requirements … 144 13-5. Oceanic Flight Standards … 144 13-6. Operation of Aircraft … 145 13-7. Equipment … 146 13-8. Special Requirements for Flights Transiting Greenland … 146 13-9. Special Requirements for Flights Transiting Iceland … 147 13-10. ELT Requirement for Turbojet-Powered Aircraft … 148 13-11. Special Requirements for Canadian Departures … 148 13-12. Major Routes Used by Short-Range Aircraft Crossing the NAT … 153 Figure 11. Four Major Routes Used by Short-Range Aircraft to Cross the North Atlantic ..155 13-13. Additional Considerations … 156

CHAPTER 14. POLAR ROUTES

14-1. Introduction … 159 14-2. Related Material … 159 14-3. Polar Communications … 160 14-4. Polar Routes … 162 14-5. CPDLC … 163 14-6. Company Communications … 163 14-7. Cruising Levels in Meters … 164 14-8. Airport Weather Reports … 164 14-9. Outside Air Temperature (OAT)/Fuel Temperatures/Fuel Freeze Points … 165 14-10. Fuel Temperature Operational Limit … 165 14-11. FMS/Autopilot (AP) Performance at the Pole … 165 14-12. Polar Emergency/Irregular … 165

CHAPTER 15. OCEANIC AND OVERFLIGHT OPERATIONS TO THE RUSSIAN

REPUBLIC AND THE COMMONWEALTH OF INDEPENDENT STATES (CIS)

15-1. Introduction … 169 15-2. Russia … 169

APPENDIX 1. GLOSSARY OF ACRONYMS/ABBREVIATIONS (6 pages) … 1 APPENDIX 2. SAMPLE OCEANIC CHECKLIST (9 pages) … 1

Page v (and vi)

1-1. PURPOSE. › 1-4. RELATED CFR REGULATIONS (current editions).

CHAPTER 1. GENERAL

1-1. PURPOSE. This advisory circular (AC) contains general information and guidance for operators planning oceanic flights, including authorizations needed for operations outside the continental United States. This includes Special Areas of Operation (SAO) such as North Atlantic Minimum Navigation Performance Specifications (NAT/MNPS), Reduced Vertical Separation Minimum (RVSM), Area Navigation (RNAV), and Required Navigation Performance (RNP) airspace.

a. Initiatives. In all geographic regions, the evolution of communication, navigation, surveillance and air traffic management (CNS/ATM) is the catalyst for initiatives such as data link, RNP, RNAV, Automatic Dependent Surveillance (ADS), and RVSM.

b. Critical Areas and Procedures. The Federal Aviation Administration (FAA) identifies critical areas and procedures such as Strategic Lateral Offset Procedures (SLOP).

c. Revisions. The dynamics of oceanic operations are such that they are constantly evolving and it is incumbent on the operators to closely monitor any changes. The FAA revised this AC to point the reader to the most current sources of international material. In many cases, the references are to a Web site. The material, however, is still found at www.faa.gov or by calling an FAA navigation specialist. This AC includes specific guidance for authorizations and other FAA policy issues. A detailed study of the FAA Web site is the best source for introduction information about oceanic, international, and remote operations.

1-2. CANCELLATION. AC 91-70, Oceanic Operations-An Authoritative Guide to Oceanic Operations, dated September 6, 1994, is canceled.

1-3. APPLICABILITY. While this document is comprehensive in design, some chapters are not applicable to all operations. The publication cycle of this AC is such that it is impossible to include up-to-the-minute details of all political, geographic, navigational, surveillance, and communication information. It is available on the applicable FAA Web sites and updated on a frequent basis. Therefore, operators should use this document only for general guidance and to verify specifics by consulting the most recent Aeronautical Information Publications (AIP), international Notices to Airmen (NOTAM), and other information from the international section on the FAA’s Web site.

1-4. RELATED CFR REGULATIONS (current editions).

• Title 14 of the Code of Federal Regulations (14 CFR) part 91, §§ 91.1 through 91.21, 91.101 through 91.143, 91.151 through 91.159, 91.167 through 19.193, 91.203, 91.205, 91.209 through 91.217, 91.221, 91.303 through 91.319, 91.323, 91.509, 91.511, 91.605, 19.609, 91.703 through 91.715, and 91.903.

• Title 14 CFR part 119, §119.59.

• Title 14 CFR part 121, §§ 121.11, 121.121, 121.163, 121.339, 121.351, 121.353, 121.355, and appendix G.

• Title 14 CFR part 125, §§ 125.23, 125.45, 125.51, 125.203, 125.209, and 125.363.

• Title 14 CFR part 135, §§ 135.43, 135.145, 135.165, 135.167, and 135.183.

1-5. BACKGROUND. Presently, there are several issues that are significant to the United States and Foreign Civil Aviation Authorities (FCAA) relative to oceanic, international, and remote flight operations. The majority of these issues involve increased air traffic density, complex and differing aviation regulations, improved technologies, and required special authorizations. Reducing separation standards on a global basis actively involves International Civil Aviation Organization (ICAO) member states. It is, therefore, critical that operators follow current procedures. Flights in airspace designated as SAOs require the operator to obtain an operational authorization in the form of operation specifications (OpSpecs) or a letter of authorization (LOA).

1-1. PURPOSE. › 1-6. GENERAL INFORMATION. The FAA has completed the following:

a. Foreign Countries. In all cases, flights to foreign countries are required to follow the rules of the countries that they overfly and those in which they intend to land. A noteworthy example would be having awareness of RNAV 5 and RNAV 1 that many of the European States have implemented. Flights in these areas require approval by the State of Registry of the operator. The FAA must approve U.S. operators.

b. Gulf of Mexico. Flights operating in the Gulf of Mexico do not involve long distances over water, but they often encounter severe tropical weather, exceed the service volume of navigation facilities, and encounter the sensitivity of national defense agencies on the southern borders of the United States. It is important to note that the airspace in the Gulf is oceanic airspace and thus demands adherence to oceanic regulations and procedures. Specifically, designated Q-routes (routes implemented in the northeast corner in the Gulf) require an RNAV system with at least one long-range navigation system (LRNS).

c. Caribbean. Governed, in most cases, by the definition of “extended over-water,” Caribbean flights also encounter situations similar to those found in the Gulf of Mexico. Crews flying in the Caribbean should have awareness of the special route structure between the coast of Florida and Puerto Rico as these routes—designated as Y-routes—have special navigation equipment requirements. Instrument charts for the area include these special navigation equipment requirements.

1-6. GENERAL INFORMATION. The FAA has completed the following:

• Revised this AC as a single-source document for operators initially planning oceanic, international, and remote flights;

• Established a tracking system and statistical database of gross navigational errors (GNE), Large Height Deviations (LHD), and reports on erosion of longitudinal separation, and LOA verification requests;

• Standardized the LOA and OpSpecs formats and the issuance of procedures for FAA inspectors through guidance in FAA Order 8900.1, Flight Standards Information Management System (FSIMS); and

• Developed Web sites for international operations that are updated periodically. This expansion allows operators to remain aware of airspace changes, policy changes, or new regulations.

NOTE: Current AIPs and NOTAMs contain the most recent information.

Par 1-6 Page 3 (and 4)

CHAPTER 2. UNITED STATES AVIATION AND THE ICAO

2-2. ICAO AND THE ICAO ANNEXES. › a. ICAO Objectives. The objectives of ICAO are to develop the…

2-1. BACKGROUND. An understanding of oceanic operations requires having knowledge of the ICAO and U.S. involvement with this organization. This background is necessary to understand the relationship between U.S. and international policy. World War II had a major impact on the technical development of aircraft, compressing 25 years of peacetime development into 6 years. There were many political and technical problems to resolve in support of a world at peace. Safety and regularity in air transportation made it necessary for airports to install Navigational Aids (NAVAID) and weather reporting systems. Standardization of methods for providing international services was vital to preclude unsafe conditions caused by misunderstanding or inexperience.

a. Standards. ICAO established standards for air navigation, air traffic control (ATC), personnel licensing, airport design, and many other important issues related to air safety. Questions concerning the commercial and legal rights of developing airlines to fly into and through the territories of another country led the United States to conduct exploratory discussions with other allied nations during early 1944. On the basis of these talks, allied and neutral states received invitations to meet in Chicago in November 1944. The outcome of this Chicago Convention was a treaty requiring ratification by 26 of the 52 states that met. By ratifying the treaty, contracting states agreed to pursue certain stated objectives, assume certain obligations, and establish the international organization that became known as ICAO.

b. Member of ICAO. As a charter member of ICAO, the United States has fully supported the organization’s goals from its inception and especially concerns itself with technical matters. Through ICAO, the United States works to achieve the highest level of standards and procedures for aircraft, personnel, airways, and aviation services throughout the world. At the same time, the United States depends upon ICAO to oversee that navigation facilities, airports, weather, and radio services provided by other nations meet international standards. Through active support and participation in ICAO, the Federal Aviation Administration (FAA) strives to improve worldwide safety standards and procedures.

c. Memorandum of Agreement (MOA) with Foreign Country. The FAA also provides technical assistance to other nations when needed. The FAA has multiple agreements with numerous foreign countries to provide technical assistance in areas such as flight inspection, training, air traffic development, loan of equipment, NAVAIDs, and supply support. MOAs detail the specific terms of these arrangements. These MOAs include descriptions of services, special conditions, financial provisions, liability information, effective dates, termination dates, and other information required for particular situations. On behalf of the FAA, the Associated Administrator of International Aviation negotiates and signs the agreements involving international activities.

2-2. ICAO AND THE ICAO ANNEXES.

a. ICAO Objectives. The objectives of ICAO are to develop the principles and techniques of international air navigation and to foster the continued development of international air transportation.

ICAO home page: www.icao.int › (4) DOC 4444–Procedures for Air Navigation Services (PANS).

b. Privileges and Obligations of Member States. Ratifying the Convention obligated member states to abide by “certain principles and arrangements in order that international civil aviation may be developed in a safe and orderly manner, and that international air transport services may be established on the basis of equality of opportunity and operated soundly and economically.” Ninety-six articles, created and accepted at the Convention, established the privileges and obligations of the member states.

c. Organizational Structure. The United Nations (UN) recognizes ICAO as a specialized agency for international civil aviation. ICAO is not subordinate to, and does not receive any line-of-command authority from, the UN.

d. ICAO Publications. Annual editions of the “Catalogue of ICAO Publications and Audio-Visual Aids” contain more complete descriptions of these and other ICAO publications. Contact ICAO at the following address for available editions of this catalog and other ICAO publications:

International Civil Aviation Organization (ICAO) 999 University Street, Montréal, Quebec H3C 5H7, Canada Tel.: +1 514-954-8219

Fax: +1 514-954-6077 SITATEX: YULCAYA E-mail: [email protected] ICAO home page: www.icao.int

(1) The ICAO Journal. ICAO publishes this document eight times annually and contains articles and a digest of ICAO meetings and activities from the previous period. Semi-annually, it contains a table showing the status of all ICAO publications involving air navigation.

(2) Final Reports of Meetings. The final reports of divisional, regional, and panel meetings include the proceedings and recommendations of each meeting. These recommendations are not effective until reviewed by the Air Navigation Commission (ANC) or another appropriate committee and approved by the Council. Approved recommendations are separately referred as appropriate for the affected states for implementation.

(3) Annexes to the Convention. The 18 ICAO Annexes to the Convention contain the International Standards and Recommended Practices (ISARP) adopted by the Council. Paragraph 2-2, subparagraph f of this chapter contains a list of the 18 Annexes with a brief description of their subject matter.

(4) DOC 4444–Procedures for Air Navigation Services (PANS). Normally developed by the ANC and based on recommendations of divisional or panel meetings, PANS are intended to amplify, in more detail, the Standards and Recommended Practices (SARP) in ICAO Annexes in certain fields. To date, PANS exist for Procedures for Air Navigation Services Aircraft Operations (PANS-OPS), Procedures for Air Navigation Services–air traffic management (PANS-ATM), and ICAO abbreviations and codes (PANS-ABC).

f. ICAO Annexes. Through international agreements, the Annexes contain… › (3) Annex 3, Meteorological Service for International Air Navigation.

(5) Regional Supplementary Procedures (SUPPS) (ICAO Document 7030). Published as Supplementary Procedures, certain procedures apply only in specific regions. A Supplementary Procedure can explain and amplify, but cannot conflict with, international standards. For convenience, a single document includes all SUPPS and group together similar procedures applicable to two or more regions. This document contains maps that identify the extent of each region and a listing of the flight information regions (FIR) included within each region.

(6) Manuals. The intention of these technical publications is to facilitate states’ implementation of SARPs by providing more detailed guidance and information (e.g., Airport Planning Manual and Manual of Procedures for Operations Certification and Inspection).

(7) ICAO Circulars. The Secretary General issues ICAO Circulars to make specialized information available to contracting states. The Council does not adopt or approve this information. Circulars include studies of statistics, summaries of treaties or agreements, analyses of technical documents, and studies of technical subjects.

e. ISARPs. Since ICAO’s inception, a main technical feature of the organization has been operational standardization of safe, regular, and efficient air services. This has resulted in high levels of reliability in the many areas that collectively shape international civil aviation, particularly with respect to aircraft, flightcrews, and ground-based facilities and services. ICAO achieved standardization through the creation, adoption, and amendment of Annexes to the Convention on International Civil Aviation, identified as ISARPs. Standards are directives that ICAO members agree to follow. If a member has a standard different from an ICAO standard, that member must notify ICAO of the difference. Recommended practices are desirable practices but not essential. The basic criterion for deciding whether a particular issue should be a standard is an affirmative answer to the question, “Is uniform application by all contracting states essential?” The applicability of a standard may be subject to certain conditions relating to such areas as terrain, traffic density, stages of flight, and climate. Any contracting state, however, should apply a standard when encountering specified conditions unless the contracting state notifies ICAO of a difference and publishes this difference in its Aeronautical Information Publication (AIP).

f. ICAO Annexes. Through international agreements, the Annexes contain adopted standards and recommended practices. The following are descriptions of the 18 Annexes:

(1) Annex 1, Personnel Licensing. Provides information on licensing of flightcrews, air traffic controllers, and aircraft maintenance personnel including medical standards for flightcrews and air traffic controllers.

(2) Annex 2, Rules of the Air. Contains rules relating to conducting visual and instrument flight.

(3) Annex 3, Meteorological Service for International Air Navigation. Provides for meteorological services for international air navigation and reporting of meteorological observations from aircraft.

f. ICAO Annexes. Through international agreements, the Annexes contain… › (18) Annex 18, The Safe Transport of Dangerous Goods by Air.

(4) Annex 4, Aeronautical Charts. Contains specifications for aeronautical charts used in international aviation.

(5) Annex 5, Units of Measurement to be Used in Air and Ground Operations. Lists dimensional systems used in air and ground operations.

(6) Annex 6, Operation of Aircraft. Enumerates specifications to ensure a level of safety above a prescribed minimum in similar operations throughout the world.

(7) Annex 7, Aircraft Nationality and Registration Marks. Specifies requirements for registration and identification of aircraft.

(8) Annex 8, Airworthiness of Aircraft. Specifies uniform procedures for certification and inspection of aircraft.

(9) Annex 9, Facilitation. Provides for the standardization and simplification of border crossing formalities.

(10) Annex 10, Aeronautical Telecommunications. Volume 1 provides for standardizing communications equipment and systems. Volume 2 standardizes communications procedures.

(11) Annex 11, Air Traffic Services. Includes information on establishing and operating air traffic control (ATC), flight information, and alerting services.

(12) Annex 12, Search and Rescue. Provides information on organization and operation of facilities and services necessary for Search and Rescue (SAR).

(13) Annex 13, Aircraft Accident and Incident Investigation. Provides for uniformity in notifying, investigating, and reporting on aircraft accidents.

(14) Annex 14, Aerodromes. Contains specifications for the design and equipment of aerodromes.

(15) Annex 15, Aeronautical Information Services. Includes methods for collecting and disseminating aeronautical information required for flight operations.

(16) Annex 16, Environmental Protection. Volume 1 contains specifications for aircraft noise certification, noise monitoring, and noise exposure units for land-use planning. Volume 2 contains specifications for aircraft engine emissions.

(17) Annex 17, Security: Safeguarding International Civil Aviation Against Acts of Unlawful Interference. Specifies methods for safeguarding international civil aviation against unlawful acts of interference.

(18) Annex 18, The Safe Transport of Dangerous Goods by Air. Contains specifications for labeling, packing, and shipping dangerous cargo.

g. AIP. Each state is responsible for developing an AIP that satisfies international requirements for the exchange of aeronautical information essential to air navigation. Each AIP contains information on air traffic, airports, NAVAIDs, special use airspace, weather, and other data vital to flightcrews coming into or flying through the airspace of a particular state. Each AIP should provide information that is adequate, accurate, timely, and designed for in-flight use. AIPs contain lists of significant differences between the national regulations and practices of the state and ICAO standards, recommended practices, and procedures. The FAA issues Notices to Airmen (NOTAM) when information is temporary or an AIP amendment cannot quickly make it available.

2-3. › d. Relationship Between 14 CFR, ICAO SARPs, and National Regulations.…

2-3. U. S. PUBLIC LAW, INTERNATIONAL AGREEMENTS, AND STANDARDS RELATED TO AIR NAVIGATION.

a. The Federal Aviation Act of 1958, as Amended (The FA Act). The FAA authority and responsibilities related to air navigation and navigation systems, practices, and procedures originate in the FA Act. Two important sections of the Act, which recodified into Subtitle VII, Aviation Programs, in Title 49 of the United States Code (49 U.S.C.), are sections 307 and 601. Section 307 of the FA Act states that, “The Secretary of Transportation is authorized and directed to develop plans and formulate policy with respect to the use of the navigable airspace; and assign by rule, regulation, or order the use of the navigable airspace under such terms, conditions, and limitations (operational procedures and navigation performance requirements) as he/she may deem necessary in order to ensure the safety of aircraft and the efficient utilization of such airspace.” Section 601 of the FA Act empowers the Secretary of Transportation to, “promote safety of flight of civil aircraft in air commerce by prescribing and revising from time to time, minimum standards and reasonable rules and regulations, governing the performance of aircraft and appliances (navigation performance and navigation systems) as may be required in the interest of safety or minimum standards, governing other practices, methods, and procedure necessary to provide adequately for national security and safety in air commerce.”

b. Protection of Persons and Property. The need to ensure protection of persons and property, both during flight and on the ground, is fundamental to Title 14 of the Code of Federal Regulations (14 CFR). Design and performance requirements in aircraft certification rules provide this protection. The operating and equipment rules related to air navigation also extensively address this protection. It is important that the regulations provide this protection equally to persons and property both during flight and on the ground. Approvals of routes and areas of en route operation must take into account the need to protect persons and property on the ground as well as during flight.

c. Equipment Redundancy. Each airplane must have enough appropriate navigation equipment installed and operational to ensure that, if one item of equipment fails at any time during the flight, the remaining equipment is sufficient to enable navigation to the degree of accuracy required for ATC. Additionally, failure of any single unit required for communication and navigation purposes (or both) must not result in the loss of another required unit.

d. Relationship Between 14 CFR, ICAO SARPs, and National Regulations. The FA Act is the authority for 14 CFR. Title 14 CFR represents the regulatory implementation of the responsibilities assigned by the FA Act and the implementation of the principles derived from

the ICAO Convention. › (3) Operating in a Foreign Country.

the ICAO Convention. The following subparagraphs discuss the relationship between 14 CFR, ICAO SARPs, and foreign national regulations.

(1) Operation Regulations for 14 CFR Part 101 and 103 Aircraft. Title 14 CFR part 91 regulates the operation of aircraft other than moored balloons, kites, unmanned rockets, and unmanned free balloons governed by 14 CFR part 101, and ultralight vehicles operated in accordance with 14 CFR part 103. The following are examples of part 91 regulations applicable outside the United States:

• Part 91, §§ 91.703(a)(1) and (a)(2) require each person operating a U.S.-registered aircraft to comply with ICAO Annex 2 when over the high seas and to comply with the regulations of a foreign country when operating within that country’s airspace.

• Section 91.703(a)(3) requires compliance with § 91.703 when not in conflict with the regulations of a foreign nation or Annex 2 of the Convention on International Civil Aviation.

• Sections 91.703(a)(4), 91.705, and appendix C specify regulatory requirements and minimum standards for operation in NAT/MNPS airspace. Section 91.706 and appendix G specify regulatory requirements and minimum standards for operating in airspace designated as Reduced Vertical Separation Minimum (RVSM) airspace.

(2) Applicable Rules for Operations. Operations under § 135.3(a)(1) require compliance with the applicable rules of that chapter while operating within the United States. Section 135.3(a)(2) specifies that while operating outside of the United States, operators must comply with the following:

• Annex 2.

• Rules of a foreign country when operating within that country.

• All the regulations of 14 CFR parts 61, 91, and 135 that are more restrictive than Annex 2 or regulations of a foreign country when compliance with these U.S. regulations would not violate requirements of Annex 2 or the foreign country.

(3) Operating in a Foreign Country. Operations under 14 CFR part 121, § 121.1 requires compliance with that part while operating within or outside the United States. Section 121.11 specifies that these operators, when operating within a foreign country, must comply with the air traffic rules of the country concerned and any local airport rules that may be in force. Section 121.11 also requires you to follow all rules of part 121 that are more restrictive than a foreign country’s rules if it can be done without violating the rules of that country. Additionally, air carriers operating under part 121 must comply with Annex 2 when over the high seas, according to § 91.1.

3-1. INTRODUCTION. › d. Precautions. The FAA advises operators to ensure full compliance…

CHAPTER 3. OCEANIC, INTERNATIONAL, AND REMOTE OPERATIONS

3-1. INTRODUCTION.

a. References. It is imperative that all pilots planning an oceanic flight become familiar with the appropriate sections of Title 14 of the Code of Federal Regulations (14 CFR), some of which are in this advisory circular (AC). Additionally, pilots should familiarize themselves with the information contained in Notices to Airmen (NOTAM), the International Flight Information Manual (IFIM), Aeronautical Information Publication (AIP), International Civil Aviation Organization (ICAO) Annexes, and regulations of the foreign countries over which they intend to fly. In addition, pilots must consider customs procedures, cultural considerations, entry, overflight procedures, and immunization requirements. The Federal Aviation Administration (FAA) Web site, www.faa.gov, publishes all of these documents either directly or through a link to ICAO documentation.

b. Legal Basis for International Operations. During oceanic flights, pilots must adhere to the U.S. regulations, ICAO Standards and Recommended Practices (SARP), and the regulations of the nations that they overfly or in which they land. Annex 2, Rules of the Air, specifically covers flight regulations for oceanic operations. Title 14 CFR part 91, § 91.703 ensures that the Rules of the Air are binding to operators of U.S.-registered aircraft operating outside the United States, and it is the aviation authority’s (AA) responsibility to ensure that pilots of U.S.-registered aircraft comply with these regulations.

c. Information Sources. Member states follow ICAO SARPS by publishing statistical aeronautical information in the AIP for a flight information region (FIR). The AIP is the state’s official publication that defines and describes the airspace, aeronautical facilities, services, and national rules and practices pertaining to air traffic. AIPs are available through the aviation departments of the publishing country. International NOTAM information is available from the U.S. International NOTAM Office.

d. Precautions. The FAA advises operators to ensure full compliance with each country’s requirements in advance. This ensures that all flights into, from, or over foreign territories comply with that territory’s regulations. Give particular attention to the permissibility of night flights and operations between sunset and sunrise. They should also consider the hours during which customs, immigration, and other services are operational. You may obtain information on a country’s normal work week from the U.S. Embassy. All countries require some form of advance notification of arrival. You should send an advance notification to permit processing and response if there is no specification regarding the number of days or hours. Pilots should carry a copy of the advance notification as well as confirmation that the notification was sent. This is particularly important for countries that do not normally return approvals. Operators should ensure that all required entry documents are available for presentation upon arrival and may need multiple copies of the following documents:

• Ownership papers.

• Management specifications (MSpecs)/operations specifications (OpSpecs)/letters of authorization (LOA).

• General declarations.

• Passenger and cargo manifests.

• Licenses.

• Crewmember certificates.

• Logbooks.

• Radio licenses.

• Detailed insurance information.

3-1. INTRODUCTION. › g. Preflight Considerations. Operators planning international flights…

e. Departure. Operators should determine the availability, types, and duration of visas, tourist cards, and other entry documents before departure. Some countries require that a traveler have a visa for the next country of entry before departure as well as proof of required immunizations for that country. You can obtain this information from the U.S. Embassy. Aircraft that remain within the territorial limits of a country for an extended period of time may become subject to import regulations and impoundment. Operators should determine in advance the number of days that an aircraft may remain in any country where the aircraft will land. For a large amount of the information needed for ICAO states, see the International Flight Information Web site (http://www.faa.gov/air_traffic/publications/ifim).

f. Planning. Adequate planning and training are the keys to a successful international flight, whether it is an airline or a single-engine light aircraft. The lead time required for planning varies with the experience and training background of the crew and the amount of assistance available from a company dispatcher or a planning agency. Planning can never start too early and should be done with at least 30 days lead time. Experienced crews flying the same route on a regular basis can reduce planning time significantly, but a new crew or a crew flying a new route should adhere to the 30-day recommendation. Many crews use planning agencies for flight planning as they only provide the information that is requested and not responsible for errors. The pilot in command (PIC) is ultimately responsible for the operation of the aircraft. A planning agency may cause an error, but the PIC is the responsible party. Some crews prefer to do their own planning, or do so for economic reasons. The following information is provided to assist in planning an oceanic operation.

g. Preflight Considerations. Operators planning international flights should complete the following tasks:

• Research the IFIM.

• Arrange all aircraft and personnel handling if the flight lands in several countries. This is extremely important if there are multiple passengers on the aircraft. It is advisable to look at each of the countries’ AIP to determine information such as visa requirements, landing permits required, and other pertinent data.

3-1. INTRODUCTION. › i. Route Analysis.

• Ensure that the correct grade of fuel is available at the planned arrival points.

• Prepare flight plan/logs and international flight plans. Ensure that the crew has all of the paperwork required for passengers and crew. Obtain and complete the following required documents:

• General declarations.

• Passenger/cargo manifests.

• Passenger passports, visas (if required), and health cards.

• Crew lists with certificate information, medical data, and passport.

• Contact customs.

• Complete the checklist and carefully review each of the items to ensure that all items are complete. A sample checklist is included in Appendix 2.

h. Itinerary Preparation. Preparing the itinerary is one of the most important aspects of an international flight. Experienced international operators often observe that the most difficult, but important, part of an international flight takes place before the aircraft departs. Here are some questions that a preflight planner must consider:

• What is the route, altitude, and destination of the flight? • Will a suitable alternate be available? • Is lodging available at the destination? • Is the appropriate grade of fuel available? • Are overflight and landing permits required? • Does the flight require a visa and are there any specific restrictions? • Will the flight be allowed cabotage? • Does a State Department warning exist for health, security, or other precautions? • Are maintenance services available at the destination airport? • Should the aircraft carry spare parts?

i. Route Analysis.

• En route airports-determine the suitability of alternate airports. • Communications, navigation, and surveillance requirements. • Computer flight planning service. • Equal time point (ETP) considerations. • Pressurization ETP where an altitude change is mandated. • Loss of one or more engines. • Combined problem (pressurization and loss of engine). • Oxygen requirements. • Terrain clearance.

m. Prior Permission Only (PPO). The flight plan provides advance notice… › (1) Preparation for Flights in Foreign Airspace.

• Passenger requirements. • Turnaround capability. • Crew rest requirements, if applicable. • Next stop arrival time.

j. Time Considerations.

• Local time. • Universal coordinated time (UTC) and Greenwich mean time (GMT). • Local time at departure airport. • Curfews. • Slot times.

k. The International Notice to Airmen (IN). The IN is a biweekly compilation of significant international information and special notices, which could affect a pilot’s decision to enter or use certain areas of foreign or international airspace. Of crucial importance to those seeking to enter areas of the world that require special considerations, this publication complements and expands upon data contained in the IFIM. The United States NOTAM Office (USNOF), a part of the National Flight Data Center Office of the Asst. Secretary of Defense (NFDC) in Washington, DC, accomplishes the distribution of U.S. international NOTAMs to foreign international NOTAM offices (NOF) and the receipt and distribution of foreign international NOTAMs.

l. International Flight Plans. All flights require flight plans when traveling into international and foreign airspace. The standard flight plan form is FAA Form 7233, International Flight Plan. You can find the most recent format for this document on the FAA Web site at www.faa.gov/air_traffic/publications/ifim/. The FAA format is similar to the ICAO format, except that it does not accept cruising speed/level in metric terms. ATC authorities should receive and must have flight plans transmitted to them in each ATC region at least 2 hours prior to entry, unless otherwise required by an en route or destination country. It is extremely important that pilots make inquiries regarding the method used for subsequent transmission of flight plan information to en route and destination points and of the approximate total elapsed time applicable to such transmissions when filing flight plans in countries outside the United States.

m. Prior Permission Only (PPO). The flight plan provides advance notice of foreign airspace penetration and facilitates effective ATC procedures. For some countries, the flight plan is the only advance notice required; other countries use the flight plan as a check against previously granted permission to enter national airspace. Acceptance of a flight plan and issuance of a flight clearance by a foreign ATC unit does not constitute official approval for airspace penetration. CAAs may require prior permission for airspace penetration. Pursue airspace violations that occur in such instances as in-flight interception may result.

(1) Preparation for Flights in Foreign Airspace. In the case of flights outside of U.S. airspace, it is particularly important for pilots to leave a complete itinerary and flight schedule with a responsible person. Keep that person apprised of the flight’s progress and instruct them to contact a Flight Service Station (FSS) or the nearest U.S. Foreign Service Post (embassy and

m. Prior Permission Only (PPO). The flight plan provides advance notice… › o. Flight Planning Firms and Ground Handling Agents. The assistance of…

consular office) if serious doubt arises as to the safety of the flight. Whenever there are reports of distressed or missing aircraft of U.S. registry or any aircraft with U.S. citizens aboard during flight in or over foreign territory or foreign territorial waters, the nearest U.S. Foreign Service Post as well as the Search and Rescue (SAR) facilities and services in that area should receive all available information.

(2) Landing and Overflight. The flightcrew must also ensure the knowledge of current and special notices relating to entry and overflight requirements. In most cases outside North America and Europe, obtain prior permission to land in or overfly a country directly from that country’s CAA. The American Embassy or consulate in a destination country may be of assistance in some instances and a required point of contact (POC) in others. Make the entry to most countries through specific airports of entry agreed to by ICAO members and listed in the ICAO Regional Air Navigation Plan (ANP), the country’s AIP, the IFIM, and other commercial publications. Depending upon the country, it may take up to 6 weeks to obtain overflight and landing permits. The requirements vary from country to country. Some countries will not allow overflights without a landing, usually to collect airspace user fees. Therefore, action to obtain landing and overflight permits must be one of the first steps in planning any flight outside of the United States.

n. Cabotage. Private pilots and commercial operators should understand cabotage, formally defined as “Air transport of passengers and goods within the same national territory.” The definition adopted by ICAO at the Chicago Convention is as follows: “Each state shall have the right to refuse permission to the aircraft of other contracting states to take on its territory passengers, mail, and cargo destined for another point within its territory.” Although cabotage rules are different in various countries and usually incorporate the term “for hire,” some countries do not allow foreign aircraft within their boundaries to carry even non-revenue passengers. The restrictions range from no restrictions to not allowed. The fines for cabotage can be extremely high; therefore, pilots and flight departments should be absolutely sure of a country’s cabotage rules before carrying passengers. The corporate aircraft restraints section for each country in the IFIM list the cabotage requirements and restrictions of individual countries. Refer to chapter II, article 7 of the Chicago Convention and the FAA Web site at www.faa.gov/air_traffic/publications/ifim/. Then, select the country of choice.

o. Flight Planning Firms and Ground Handling Agents. The assistance of Fixed-Base Operators (FBO) or airport service organizations may be nonexistent at overseas destinations outside of Western Europe. Many countries do not have sufficient general aviation traffic to require these services or to generate any profitability. Therefore, the assistance of a ground-handling agent may be essential and should expedite handling. A domestic or regional airline or U.S. flag (international) airline with operations at the specific foreign destination airport can frequently provide some of the necessary services, such as help with customs, immigration, public health procedures, and expediting shipment of spare parts. These agents may also arrange aircraft maintenance. Flight planning firms may also provide for these services. Firms that specialize in obtaining overflight and landing permits, security information, computerized flight planning, charts, international NOTAMs, communication services, flight following, weather, ground handling of passengers, and ground handling of aircraft offer a wide range of services. It is important to remember that the responsibility for a flight rests with the pilot, not with ground handlers and/or flight-planning firms.

m. Prior Permission Only (PPO). The flight plan provides advance notice… › u. Aircraft Document Requirements. Title 14 CFR requires that aircraft…

p. Journey Logbook. Article 34 of the Chicago Convention determined that it was extremely important that each aircraft have a journey logbook. Annex 2 requires this standard for operations engaged in international aviation. The aircraft should carry a journey logbook containing the particulars of the aircraft, crew, reporting points, communication problems, and any unusual circumstances surrounding the flight.

NOTE: An electronic version of the journey logbook is acceptable but you should retain the data at least 90 days for support in the event of an oceanic error.

q. Significant Sections of the Chicago Convention. Pilots planning international flights should know the regulations of their country, special regulations for international flight, and the Articles of the Chicago Convention. Give particular attention to Article 1, “Sovereignty;” Article 12, “Rules of the Air;” and Article 40, “Validity of Endorsed Certificates and Licenses.” We single out these three Articles because of their importance in regulating international flights as all pilots who are flying internationally should thoroughly understand them.

r. Personal Documentation Requirements. When planning a trip to or from a foreign country, obtain proper personal documentation for all participants. The FAA requires the flightcrew to carry at least a restricted radio telephone operator’s license, even though domestic operations no longer require the license. You may find the requirements for individual countries in the IFIM and other commercial publications. The responsibility for documentation varies with individual operations, but the PIC will bear the responsibility either directly or indirectly because of the effect on the flight operation.

s. Passports. Contact the nearest passport agent for more information. The U.S. Government section of most telephone books list the telephone numbers.

t. Visas. Requirements for a visa may differ for passengers and flightcrews. Investigate the country or countries of interest for visa and passport requirements on the FAA Web site at www.faa.gov/air_traffic/publications/ifim/. Then, select country of choice.

u. Aircraft Document Requirements. Title 14 CFR requires that aircraft carry the Airworthiness Certificate, the aircraft registration certificate (a temporary registration certificate is not acceptable for international travel), a Federal Communications Commission (FCC) license (commonly referred to as radio station license), and the operator’s manual with Weight and Balance (W&B) information onboard during international flights. The operator is responsible for ensuring the need for airframe logbooks, the engine logbooks, and insurance certificates. For additional details for operations of corporate aircraft, contact the company’s aviation underwriter. In operations of private aircraft, if the owner is the pilot or is onboard the aircraft, there are usually no insurance difficulties. However, if a private aircraft owner is not onboard the aircraft, many countries require a letter from the owner that authorizes international flight in that specific country before they will allow operations within their country (you can find specific information on this letter and other requirements in the AIPs of the countries concerned). Some countries require an LOA from the state (country) of registry or the state of the operator before operating the aircraft in those countries. Special operations (e.g., Reduced Vertical Separation

u. Aircraft Document Requirements. Title 14 CFR requires that aircraft… › (2) Onboard Aircraft Documentation.

Minimum (RVSM) and minimum navigation performance specification ((MNPS) airspace operations, etc.) also require LOAs.

(1) Export Licenses and Import Duty Receipts. Export licenses from the U.S. Department of Commerce are necessary for certain navigation systems and/or aircraft if the operations will include certain countries. Retain a copy of the import duty receipt in the aircraft’s file for aircraft that are U.S. registered and were manufactured abroad. The receipt, which proves that the operator legally imported the aircraft into the United States, may require a return to the United States. The IFIM and numerous commercial publications delineate aircraft entry requirements. Refer to the U.S. Department of Commerce Web site at www.commerce.gov for additional information.

(2) Onboard Aircraft Documentation. Include the following list of documents as aircraft documentation. Any aircraft flying internationally should carry these documents onboard. The Articles of the Chicago Convention specify items marked with a double asterisk (**). It is important to note that the operator is responsible for additional documentation requirements that this list does not include:

• Airworthiness Certificate. **

• Aircraft registration (international flights do not allow temporary certificates). **

• Radio station license.

• Minimum equipment list (MEL) or Master Minimum Equipment List (MMEL) if operator plans on operating under this option. **

• Aircraft Flight Manual (AFM) with W&B information. Metric conversion tables, if applicable.

• OpSpecs/MSpecs/LOA for Special Areas of Operation (SAO), if applicable.

• Copies of aircraft and engine logbooks.

• Certificates of insurance, if applicable.

• Export licenses for aircraft navigation equipment (U.S. requirement). Check with the U.S. Department of Commerce or its Web site at www.commerce.gov.

• Import papers for aircraft of foreign manufacture.

• Copies of overflight and landing permissions.

• Authorization letters from the operating company or the aircraft owner (original signature required), if applicable.

• Master document.

• Passenger manifest containing complete names of passengers and places of embarkation and destinations of each. **

3-2. EQUIPMENT. › a. ICAO Standards. Annex 6 (Part I–International Commercial Air…

• If the aircraft carries cargo, a manifest and detailed declaration of the cargo. **

• Check with the Transportation Security Administration (TSA) or its Web site (www.tsa.gov) for any applicable requirements. **

3-2. EQUIPMENT.

a. ICAO Standards. Annex 6 (Part I–International Commercial Air Transport— Aeroplanes and Part II–International General Aviation—Aeroplanes) to the Convention on International Civil Aviation details standards with respect to required equipment. This equipment list may be incomplete but includes the following examples (see ICAO Web site (www.icao.int) to purchase current list):

• Accessible and adequate medical supplies appropriate to the aircraft’s passenger carrying capacity.

• Portable fire extinguisher of a type that, when discharged, will not cause dangerous contamination of the air within the airplane. Locate at least one extinguisher in the pilot’s compartment and in each passenger compartment that is not readily accessible to the flightcrew.

• A seat or berth for each person over the age specified by the state of the operator.

• A seatbelt for each seat and a restraining belt for each berth.

• A seatbelt and a safety harness for each flightcrew seat. The safety harness will incorporate a device that will automatically restrain the occupant’s torso in the event of rapid deceleration.

• A means of ensuring that the passengers have the following information and instructions conveyed to them:

• When to fasten seatbelts;

• When and how to use oxygen equipment if there is a requirement for the carriage of oxygen;

• Restrictions on smoking;

• Location and use of life jackets or equivalent individual flotation devices if required for carriage; and

• Location and method of opening emergency exits.

• An operations manual or those parts of the manual that pertain to flight operations.

f. Performance Requirements. › (1) Operator Responsibilities.

• The AFM or other document(s) containing performance data required for the application of operating limitations, and any other information necessary for the operation of the airplane within the terms of its Certificate of Airworthiness.

• Current and suitable charts to cover the route of the proposed flight and any route along which it is reasonable to expect that you may divert the flight.

• Flight recorders (data recorder and cockpit voice recorder) as specified below.

b. Traffic Alert and Collision Avoidance Systems (TCAS). Several 14 CFR parts require the use of TCAS. Operators should review the specific regulation that pertains to their operations to ensure that these TCAS requirements are met. Operators are also responsible for ensuring they comply with any foreign airspace requirements concerning the use of TCAS. In addition, RVSM operations have TCAS requirements contained in part 91 appendix G. Although non-radar environments cannot verify TCAS indications, it does perform an alerting function that provides the crew with an exceptional aid to situational awareness (SA).

NOTE: International flight information may reference Airborne Collision Avoidance System (ACAS) (e.g., ACAS II is TCAS II Version 7.0, or later).

c. Flight Recorders. Operators are responsible for ensuring they comply with 14 CFR and any foreign airspace requirements concerning the use of flight data recorders.

d. Cockpit Voice Recorders. Operators are responsible for ensuring they comply with 14 CFR and any foreign airspace requirements concerning the use of cockpit voice recorders.

e. Required Equipment for Oceanic and Remote Airspace. Operators are responsible for ensuring compliance with 14 CFR and any foreign airspace requirements concerning the use of over-water equipment. The following equipment is not a complete list but includes:

• Life rafts; • Survival radio equipment; • Emergency locator transmitter (ELT) radio equipment; • Pyrotechnic signaling devices; • Navigation equipment; and • Communication equipment.

f. Performance Requirements.

(1) Operator Responsibilities. Operators are responsible for ensuring compliance with the following performance issues:

• Terrain clearance. • Fuel. • Emergency landing site selection. • One or two-engine inoperative requirements.

(2) ICAO Rules for Airworthiness of Aircraft. In addition to the specific equipment for over-water operations, Annex 8 to the Convention on International Civil Aviation details ICAO rules with respect to the airworthiness of aircraft. Chapter 8 of Annex 8 details ICAO rules relative to instruments and equipment. Commercial operators should note that 14 CFR part 121, §§ 121.343, 121.353, and 121.359 may or may not be more stringent than the ICAO regulations. In either case, the more stringent regulations apply to U.S.-registered aircraft. Operators of large and turbine powered, multiengine aircraft must note that §§ 91.509 and 91.511 may also be more or less stringent than ICAO requirements, but the more restrictive regulations apply to U.S.-registered aircraft.

3-2. EQUIPMENT. › j. Survival Equipment. Operators are responsible for ensuring they…

g. W&B Control for Part 121 and 135 Operations. The current edition of AC 120-27, Aircraft Weight and Balance Control, includes a method and procedures for developing a W&B control system. It provides guidance to certificate holders required by part 121 to have an approved W&B program, or certificate holders under 14 CFR part 135 who elect to have an approved program. The significance of this document to international operators is that emergency equipment for international operations is included in the empty weight of the aircraft.

h. Navigation Equipment. Section 91.1(b) states in part that each person operating an aircraft in the airspace overlying the waters between 3 and 12 nautical miles (NM) from the U.S. coast shall comply with § 91.703. Section 91.703 requires that civil aircraft comply with ICAO Annex 2 when operating over the high seas (beyond 3 NM under § 91.1(b)). Annex 2 requires that “Aircraft shall be equipped with suitable instruments and with navigation equipment appropriate to the route being flown.” In addition, ICAO Annex 6, Part II stipulates that an airplane operated in international airspace have navigation equipment which will enable it to proceed in accordance with the flight plan and with the requirements of the Air Traffic Service (ATS). ICAO Annex 6, Part I contains standards and recommended practices adopted as minimum standards for all airplanes engaged in air carrier operations. Part II contains the standards and practices for general aviation international air navigation. These parts require that those airplanes operated under IFR at night, or on a visual flight rules (VFR)-controlled flight (such as in control area (CTA)/FIR oceanic airspace) have installed and approved radio communication equipment capable of conducting two-way communications at any time during the flight. The appropriate authority for the airspace where you conduct the flight may prescribe the aeronautical stations and frequencies used for two-way communications. You can find additional ICAO regulations for aircraft radio equipment in Article 30 of the Chicago Convention. (Refer to Chapter 10 for information on long-range navigation.)

i. Specific Equipment Requirements. Specific operations, such as 14 CFR part 121, 125, and 135 regulated flight, require that aircraft have the equipment required by these parts in addition to any ICAO requirements.

j. Survival Equipment. Operators are responsible for ensuring they comply with 14 CFR and any foreign airspace requirements concerning use of survival equipment. This equipment list is not complete but includes the following items:

• Life preserver for each occupant.

• Rafts or slide/rafts with appropriate buoyancy and sufficient capacity for all aircraft occupants. The rafts might have the following items equipped:

• Lines, including an inflation/mooring line with a snap-hook, rescue or lifeline, and a heaving or trailing line.

• Sea anchors.

• Raft repair equipment such as repair clamps, rubber plugs, and leak stoppers.

• Inflation devices including hand pumps and cylinders (carbon dioxide bottles).

• Safety/inflation relief valves.

• Canopy and equipment for erecting the canopy.

• Position lights.

• Hook-type knife, sheathed and secured by retaining line.

• Placards that give the location of raft equipment and that are consistent with placard requirements.

• Propelling devices such as oars or glove paddles.

• Water catching devices including bailing buckets, cups, and sponges.

• Signaling devices including the following:

• At least one approved pyrotechnic device. • Mirror. • One spotlight or flashlight, spare bulb, and at least two D-cell batteries or equivalent. • One police whistle. • One dye marker. • Radio beacon with water-activated battery. • Radio reflector.

• One magnetic compass.

• A 2-day supply of rations supplying at least 1,000 calories a day for each person.

• One desalination kit for every two persons the raft is rated to carry or two pints of water for each person the raft is rated to carry.

• One fishing kit.

3-3. ATC. › b. Flight Planning. A flight plan is required for all flights that…

• One book on survival appropriate for any area.

• A survival kit, appropriately equipped. The kit could include some of the following items:

• Triangular cloths. • Bandages. • Eye ointments. • Water disinfection tablets. • Sun protection balsam. • Heat retention foils. • Burning glass. • Seasickness tablets. • Ammonia inhalants.

3-3. ATC. Oceanic and remote airspace is mostly non-radar (i.e., where the separation of aircraft does not depend on ground-based radar coverage) and considered procedural airspace. Therefore, it is paramount crews operate with strict discipline and adherence to ATC clearances and all procedures, both normal and contingency. You may find detailed ICAO procedures for specific geographical areas in ICAO Regional Document 7030, Regional Supplementary Procedures, and in this AC. FAA ATC generally base their procedures for oceanic and remote airspace on ICAO standards.

NOTE: ATC monitors the compliance with the issued clearance for all aircraft entering and/or departing international airspace under U.S. jurisdiction. Navigation performance is monitored by the United States for all aircraft entering and/or departing international airspace under U.S. jurisdiction. All deviations of 20 NM or more are reported and investigated.

a. U.S. Oceanic Service Areas. The United States provides ATS in oceanic airspace as follows:

• Atlantic Ocean: New York, Miami, and San Juan FIRs. • Gulf of Mexico: Miami and Houston FIRs. • Pacific Ocean: Oakland and Anchorage FIRs.

b. Flight Planning. A flight plan is required for all flights that cross international borders. IFR operations in oceanic airspace generally start at 6,000 feet. VFR operations below 6,000 feet must comply with all applicable regulations and foreign airspace requirements. The FAA only permits operations in offshore airspace (the airspace between the U.S. 12-mile limit and the oceanic control area (OCA)/FIR boundary) on a VFR flight plan between sunrise and sunset and at or below flight level (FL) 200. Even though you may legally conduct flights using VFRs, experience indicates that you will encounter instrument meteorological conditions (IMC) at some

d. Position Reporting. Make position reports to the ATS provider for… › (2) Oceanic Position Procedures.

point in a transoceanic flight. Consequently, we recommend that the pilot is instrument rated, that the aircraft meet the equipment requirements for IFR flight, and file an IFR flight plan.

c. Navigation/Communication Equipment. In most cases, aircraft operating over the high seas will not have adequate very high frequency (VHF) radio and/or ICAO standard Navigational Aid (NAVAID) VHF Omnidirectional Range (VOR), VOR/distance measuring equipment (DME), and non-directional radio beacon (NDB)) coverage. High frequency (HF) communication capabilities, provided by Aeronautical Radio, Inc. (ARINC), are available throughout most of U.S.-controlled oceanic airspace. In some U.S.-controlled oceanic airspace, you can use Global Navigation Satellite System (GNSS) and data link. Notwithstanding the fact that pilots must comply with all regulations applicable to their flight, all aircraft operating over the high seas must equip suitable instruments and navigation equipment appropriate to the route to be flown (§ 91.703, ICAO Annex 2, section 5.1.1, and this chapter). The aircraft must also equip a functioning two-way radio to maintain a continuous listening watch on the appropriate radio frequency and establish two-way radio communications with the appropriate ATC unit (ICAO Annex 2, section 3.6.5.1). It is not acceptable to depend on radio relay operations to satisfy this requirement.

NOTE: Oceanic and remote airspace communication and navigation requirements are rapidly evolving. The operator must ensure it has the appropriate approvals based on the airspace requirements.

d. Position Reporting. Make position reports to the ATS provider for the airspace where you operate the aircraft. In addition, when so prescribed by the appropriate AIP or requested by ATC, make the last position report before passing from one FIR or CTA to an adjacent FIR or CTA to the ATS you are about to enter. Make position reports when over the fix, or as soon as passing, each designated compulsory reporting point. When required for ATS purposes, the appropriate ATS may request additional reports over other points.

(1) Appropriate Time Intervals for Position Reports. On routes not defined by designated significant points, make reports as soon as possible after the first half hour of flight and at hourly intervals thereafter. The maximum interval is 1 hour and 20 minutes. The appropriate ATC unit, when required for ATS purposes, may request additional reports at shorter intervals of time. In cases where adequate flight progress data is available from other sources such as ground radar, and in other situations where the omission of routine reports from selected flights is acceptable, flights may be exempt from the requirement to make position reports at each designated compulsory reporting point or interval. However, you should take account of the requirement for making, recording, and reporting of routine aircraft observations (see “Reporting of Operational and Meteorological Information” below).

(2) Oceanic Position Procedures. Oceanic position procedures call for aircraft reporting of all designated reporting points when following a designated oceanic route. If operating in airspace approved for the use of data link or in a separation standard that requires the use of data link, you may accomplish position reporting with a periodic contract with Automatic Dependent Surveillance-Contract (ADS-C). Otherwise, report positions at designated lines of latitude and longitude. Flights whose tracks are predominantly east and west will report over each 5 or 10° meridian of longitude. Flights whose tracks are predominantly north and

f. ATC Service. › (2) You may find the most current information on oceanic separation…

south will report over each 5° or 10° parallel of latitude. If the speed of the aircraft is such that it will allow it to traverse 10° within 1 hour 20 minutes or less and over each 5° if the aircraft is slower, make reports over each 10° parallel/meridian. Transmit position reports at the time of crossing the designated reporting point or designated reporting line, or as soon thereafter as possible. Flights operating within international airspace should make position reports, either directly or by relay.

NOTE: Transmit relays over the appropriate air-to-air frequency and not over the emergency frequency.

e. Position Report Format.

• Complete aircraft call sign.

• For flights reporting coordinates rather than specified named reporting points, east-west oriented flights report latitude in degrees and minutes, longitude in degrees only. North-south oriented flights should report latitude in degrees only and longitude in degrees and minutes.

• Position time in four digits universal coordinated time (UTC).

• FL.

• Next fix and estimate over next fix in four digits.

• Name of subsequent fix.

NOTE: ATC may require meteorological reports, if requested.

f. ATC Service.

(1) Air route traffic control centers (ARTCC) in oceanic controlled airspace provide ATC separation to all flights. These facilities issue clearances and instructions providing separation vertically and horizontally (laterally and longitudinally). The horizontal distances between separated aircraft generally exceed those applied over land. Controllers may apply reduced longitudinal separation in oceanic airspace between turbojet aircraft cleared to maintain a specific Mach speed. In some cases, controllers can apply reduced separation without the application of Mach number technique.

NOTE: You can find specific information regarding ATC separation standards in the current edition of FAA Order 7110.65, Air Traffic Control.

(2) You may find the most current information on oceanic separation standards and operational authorizations on the following FAA and international Web sites:

• www.faa.gov/about/office_org/headquarters_offices/ato/service_units/enroute/ rvsm/.

(3) Barometric Pressure for Local Altimeter Setting (QNH). › (b) When an aircraft that receives a clearance as number one to land…

• www.faa.gov/air_traffic/publications/ifim/.

• http://www.paris.icao.int.

g. Warning Areas. International airspace has established warning areas to contain operations hazardous to non-participating aircraft. The FAA and the military may jointly use some of these areas. The FAA will issue instrument flight rules (IFR) clearances through these areas whenever hazardous operations are not taking place. Carefully review charts for those areas while flight planning, taking note of the area operating times and restrictions.

NOTE: Operators are also responsible for knowing the requirements for prohibited and restricted airspace in oceanic operations.

h. Altimeter Settings. Operations in international airspace demand that pilots are aware of, and understand the use of, the three types of altimeter settings.

NOTE: Most overseas airports give altimeter settings in hectopascals (hPa) (millibars). Therefore, it is imperative that pilots are able to convert inches of mercury to hPa or hPa to inches of mercury.

(1) Altitude Above Ground (QFE). A local altimeter setting equivalent to the barometric pressure measured at an airport altimeter datum, usually signifying the approach end of the runway is in use. At the airport altimeter datum, an altimeter set to QFE indicates zero altitude. If required to use QFE altimetry, altimeters are set to QFE while operating at or below the transition altitude and below the transition level. On the airport, the altimeter will read “0” feet.

(2) Barometric Pressure for Standard Altimeter Setting (QNE). Use the altimeter setting (en route) at or above the transition altitude (FL 180 in the United States). The altimeter setting is always 29.92 inches of mercury/1013.2 hPa for a QNE altitude.

NOTE: Transition levels differ from country to country and pilots should be particularly alert when making a climb or descent in a foreign area.

(3) Barometric Pressure for Local Altimeter Setting (QNH). A local altimeter setting equivalent to the barometric pressure measured at an airport altimeter datum and corrected to sea level pressure. At the airport altimeter datum, an altimeter set to QNH indicates airport elevation above mean sea level (MSL). Altimeters are set to QNH while operating at and below the transition altitude and below the transition level.

(a) For flights in the vicinity of airports, express the vertical position of aircraft in terms of QNH or QFE at or below the transition altitude and in terms of QNE at or above the transition level. While passing through the transition layer, express vertical position in terms of FLs when ascending and in terms of altitudes when descending.

(b) When an aircraft that receives a clearance as number one to land completes its approach using QFE, express the vertical position of the aircraft in terms of height above the airport elevation during that portion of its flight for which you may use QFE.

c. Inflight Broadcast Procedures. Some remote geographic regions of the… › (2) Operation Manuals.

i. Reporting of Operational and Meteorological Information. When an aircraft en route reports operational and/or routine meteorological information at points or times that require position reports, give the position report in a format that ATC requires.

j. National Security. Title 14 CFR part 99 governs national security in the control of air traffic. Following the events of September 11, 2001, the threat of terrorism has brought about numerous changes to security protection procedures in the United States. The FAA expects many additional changes in the United States and internationally will take place and operators should check the latest AIP and all NOTAMs to ensure compliance with security requirements. Additionally, operators intending to operate in or cross any United States air defense identification zone (ADIZ) should make a detailed review of part 99 and the IFIM.

k. International Interception Procedures. There are occasions that require pilots to transmit instructions to pilots of intercepted aircraft. ICAO Annex 2, chapter 3, paragraph 3.8, and attachment A contains guidance for international interception procedures. Appendix 1 of Annex 2 contains international interception signals.

3-4. OCEANIC COMMUNICATIONS. Radio frequencies are constantly changing. Thus, it is important that operators consult current oceanic charts and the FAA Website at www.faa.gov/air_traffic/publications/ifim/ for the most up-to-date information.

a. Data Link Communications. We base data link requirements on ICAO standards (for additional guidance, see AC 120-70A, Operational Authorization Process for Use of Data Link Communication System, current edition). Operators should consult geographic-specific areas of this document. Operators can also consult the Future Air Navigation System (FANS) Operation Manual for data link procedures and operations.

b. Satellite Communications (SATCOM) Voice. The current requirements for remote oceanic operations are two HF radios. At this time, non-routine and emergency purposes only allow SATCOM Voice. As this technology evolves, operators must ensure that they comply with the latest authorizations.

c. In-flight Broadcast Procedures. Some remote geographic regions of the world, which provide only limited communication and ATS, require the pilots’ understanding and regular use of in-flight broadcast procedures.

(1) Navigation Charts. Commercially-published navigation charts contain details of communication procedures on inserted panels. In addition, the North Atlantic Systems Planning Group (NAT SPG) publishes the North Atlantic MNPS Airspace Operation Manual, which is available on the following Web site: www.paris.icao.int/. This North Atlantic MNPS Airspace Operations Manual details all aspects of North Atlantic Operations (NAT/OPS) and includes communication and navigation procedures. The guidance and information material contained here concerns flight operations in the NAT region. It deals primarily with approval for operations in the NAT region and with the planning and management of such operations. It addresses mainly state aviation authorities/administrations and ATS Provider States and Operators.

(2) Operation Manuals. Some of the material in this document is of interest to pilots; however, more detailed information for pilots is in the North Atlantic MNPS Airspace

3-5. › b. Application of Master Document. Strict procedures should be used in…

Operations Manual (issued by the European and North Atlantic (EUR/NAT) Offices of ICAO) and in the North Atlantic International General Aviation Operations Manual (issued by the FAA). NAT SPG, on its behalf, produce these two manuals. Although primarily intended for use by pilots, it is important that the operators use the manuals to ensure that flightcrews, for whom they are responsible for, have adequate training and equipment for NAT/OPS.

NOTE: You can download the North Atlantic International General Aviation Operations Manual from the FAA Web site at www.faa.gov/atpubs.

d. Summary of Communication and Reporting Procedures. Maintain continuous contact with the controlling agency. This can be through VHF, HF, data link, SATCOM Voice or Selective Call (SELCAL). The range of VHF is approximately 200 NM; communication beyond that distance requires HF or SATCOM data link. A family of frequencies is normally assigned based on route and/or the state where the aircraft is registered. En route charts list these families of frequencies.

e. Emergency Frequencies.

• VHF: 121.5. • Ultrahigh frequency (UHF): 243.0. • HF: 2182/4125.

3-5. NAVIGATION PROCEDURES (NAVIGATION SENSORS—INERTIAL NAVIGATION SYSTEM (INS), INERTIAL REFERENCE SYSTEMS (IRS), OR GNSS).

a. Journey Logbooks. ICAO Annex 2 requires the use of a journey logbook, also known as the “master” document. This “master” document is typically a computer flight plan (CFP). Operator procedures must include a designated “master” document for use on the flight deck. This document must include information that sequentially lists the waypoints that define the routes, distances between the waypoints, and any other navigation information pertinent to the cleared route. Misuse of the master document can result in serious navigational errors.

b. Application of Master Document. Strict procedures should be used in the management of this document. These procedures should include the following:

NOTE: These procedures are general; operators should consult specific guidance based on the type of long range navigation system (LRNS) configuration.

• Use only one copy of the master document in the cockpit.

• Use a waypoint/numbering sequence procedure from the outset of the flight. Enter this sequence on the master document and also use it to store waypoints in the navigational computer. Adopt the appropriate symbology to indicate the status of each waypoint listed on the master document. For example:

• Verify the waypoints by comparing the master document and the LRNS;

a. Plotting and Systematic CrossChecking of Navigation Information.… › (3) Turboprop Operations.

• Circle the waypoint, waypoint number, or symbol to signify that another crewmember independently cross-checks the entry of the coordinates in the navigation computer;

• Tick or diagonally slash the circled waypoint, waypoint number, or symbol to signify the cross-checking of track and distance information within a specified tolerance; and

NOTE: Some operators use a diagonal line approaching a waypoint to confirm a subsequent waypoint to include coordinates, track, and distance.

• Cross out the circled waypoint, waypoint number, or symbol to signify that the aircraft has passed the waypoint. Pilots must verify all navigational information contained in the master document against the best available primary data source. Cross out old waypoints and insert the new information.

• If they receive an ATS route change or the ATC clearance changes, pilots must update the master document to reflect the change.

• While obtaining ATC clearances, it is recommended to wear headsets because loudspeaker distortion is known to result in errors. Two qualified crewmembers must monitor and independently verify all clearances received. The crew should read all waypoint coordinates back in detail unless approved local procedures make this unnecessary. In that case, cross-check each detail with the master document.

3-6. POSITION PLOTTING.

a. Plotting and Systematic Cross-Checking of Navigation Information. During all phases of flight in Class II navigation, each operator’s long-range navigation program (LRNP) will require the standardized application of disciplined, systematic cross-checking of navigation information.

(1) Plotting Procedures Impact. Plotting procedures have had a significant impact on the reduction of gross navigation errors (GNE). There is a requirement to plot the route of flight on a plotting chart and to plot the computer position approximately 10 minutes after waypoint passage. This may or may not require plotting, depending upon the distance between the standard ICAO ground-based NAVAIDs. This applies to all operators.

(2) Turbojet Operations. All turbojet operations, where the route segment between the operational service volume of ICAO standard ground-based NAVAIDs exceeds 725 NM, require plotting procedures.

(3) Turboprop Operations. All turboprop operations, where the route segment between the operational service volume of ICAO standard ground-based NAVAIDs exceeds 450 NM, require plotting procedures.

d. INS/IRS/Inertial Reference Units (IRU) System Alignment. Complete… › (1) Align Mode.

(4) Plotting Procedures for Special Conditions. The Administrator requires plotting procedures for routes of shorter duration that transit airspace where special conditions exist, such as reduced lateral and vertical separation standards, high density traffic, proximity, or potentially hostile border areas.

(5) Reviewing and Revising Approvals. Review and revise any existing approvals that differ from the plotting requirements in this chapter and Class II navigation procedures as necessary. Direction and guidance is available from the navigation specialists in coordination with AFS-400.

(6) Plotting Charts. The FAA requires crews to use a plotting chart to provide themselves with a visual presentation of the intended route. Regardless of the type of LRNS in use, operators must use plotting charts. Plotting the route will increase SA and reveal errors or discrepancies in the navigational coordinates that flightcrews can correct before such errors can cause a deviation from the ATC cleared route. As the flight progresses, plotting the position approximately 10 minutes after passing each waypoint helps confirm that the flight is on course. If the plotted position indicates off track, the flight may have deviated unintentionally and the flightcrew should investigate at once.

(7) Plotting Chart Requirements. The plotting chart must include, at a minimum:

• The route of the currently effective ATC clearance;

• Clearly depicted waypoints using standardized symbology; and

• Ten-minute plotted positions after passing each oceanic waypoint, including coordinates, time, and graphic depictions of all ETPs.

NOTE: Operators’ SA should include such items as alternate airports and proximity of other tracks.

b. Human Factors Issues for Confirmation of Currently Effective ATC Clearance. When cross-checking the LRNS entries or the plotting chart entries, pilots should read from “entered” data back to the master document.

c. Relief Crewmembers. Flightcrews conducting long-range operations may include a relief pilot. In such cases, crews must ensure the continuity of the operation and brief the relief pilot on all current operational issues affecting the flight.

d. INS/IRS/Inertial Reference Units (IRU) System Alignment. Complete INS alignment and switch the equipment to “nav” mode prior to releasing the parking brake at the ramp. There are various ways of ensuring that there is adequate time for this operation.

(1) Align Mode. Have the first crewmember on the flight deck place the system in “align” mode as early as possible. At short transit stops, leave the equipment in “nav” mode provided that the system errors are not so large as to require INS realignment. The decision to realign may depend on the size of the error as well as the length and nature of the next leg. You cannot recharge INS batteries, which usually have a limited-life, onboard if allowed to run down.

3-6. POSITION PLOTTING. › g. INS Loading of Initial Waypoints. Two people working in sequence and…

(2) Monitor Ground Power Interruption. If the INS is left in “nav” mode during a transit stop, or if you switch the INS on for alignment, it is imperative that an individual is responsible for monitoring ground power interruption.

(3) Overheat Protection. Some INS systems provide overheat protection in “standby” and “align,” but not in other modes.

(4) Align at Tropical Terminals. During stops at tropical terminals, put the mode selector directly to “align” (not through “standby,” which would cause realignment).

e. Initial Insertion of Latitude and Longitude. Early in the course of the preflight check, load the aircraft’s position into the INS and verify. Check this position against an authoritative reference source before insertion. Any latitude error in the initial position will introduce a systematic error that you cannot remove during flight by updating, resulting in erroneous position indications. Check for a correct insertion of present position before the “align” mode is selected and the position is recorded in the master document. Subsequently, both pilots independently make silent position checks during an early stage of the preflight check. In the case of some INS, insertion errors exceeding 1º of latitude will activate a malfunction light. However, very few systems provide similar protection against erroneous longitudinal insertion errors. At all times, take care to ensure that previously inserted coordinates are correct.

f. Verification of Present Position/Initial Position. Regardless of the type of LRNS or the method of insertion, crews will verify current ramp position in the LRNS against current aeronautical publications.

g. INS Loading of Initial Waypoints. Two people working in sequence and independently must conduct the entry of waypoint data into the navigation system as a coordinated operation. One should key in the data and the other person should recall and confirm the data against source information. It is not sufficient for one crewmember to simply observe another crewmember entering the data. The pilots should use waypoint 1 for the ramp position of the aircraft. The pilots should load at least two additional waypoints while the aircraft is on the ramp or they may load all waypoints at this time. However, it is more important to ensure that the second waypoint is inserted accurately than to attempt to load all waypoint data. The second waypoint should associate with the first significant position along the route (approximately 100 NM from departure point). Positions associated with ATC standard instrument departures (SID) should not normally be used for this purpose.

During flight, the control display unit (CDU) should maintain at least two current waypoints beyond the navigated sector until the pilots load the destination ramp coordinates. The pilots should be responsible for loading, recalling, and checking the accuracy of the loaded waypoints. Each pilot should cross-check the other’s work. In no case should this process engage the attention of both pilots simultaneously during flight. An acceptable procedure is for the pilots to independently load their own waypoints and then cross-check them. The pilot responsible for verification should work from the CDU display to the master document, lessening the risk of seeing what is expected rather than the actual information. After the pilots load the initial waypoints, they should select the route between waypoints 1 and 2 and the auto track change.

k. Approaching the Ocean. The FAA requires crews to verify the accuracy… › (2) Updating Navigation the System.

h. INS Flight Plan Check. The purpose of the flight plan check is to ensure complete compatibility between the master document and the programming of the navigation system. To verify the correct distance from the ramp position to waypoint 2, select “dis/time.” You may have to consider an appropriate allowance since the great circle distance shown on the CDUs may be less than the flight plan as a consequence of the additional mileage involved in ATC SIDs. However, a significant disparity requires a recheck of “pos” and waypoint 2 coordinates:

• Select “remote” and track change 1-2. Check the accuracy of the indicated distance against that listed in the master document.

• Select “dstrk” and check that the desired track indicated on the CDU is the same as that in the master document. This track check will reveal any errors in the latitude and longitude designators.

• Perform similar track and distance checks for subsequent pairs of waypoints and any discrepancies between the CDU information and the master document. Coordinate these checks against the master document between themselves.

• After checking each leg of the flight as described above, make a note on the master document using the appropriate symbols.

i. INS Procedures Leaving the Ramp. If the aircraft moves before initiating the “nav” mode, realign the INS. Relocate the aircraft so that it does not block the gate or otherwise interfere with traffic while the realignment takes place. After leaving the ramp, check INS groundspeeds. Perform a check of the malfunction codes while the aircraft stops but after it has taxied at least part of the way to the takeoff position. Any significant groundspeed indication while stationary may indicate a faulty unit.

j. In-flight. If you conduct the initial part of the flight along airways, the flightcrews should use the airways facilities as the primary NAVAIDs and monitor the aircraft navigation system to ascertain which system is giving the most accurate performance.

k. Approaching the Ocean. The FAA requires crews to verify the accuracy of the LRNS before entering Class II airspace. Crews must complete the accuracy verification (without updates) using ground-based NAVAIDs. The crew will conduct the gross error check of the LRNS in Class I airspace. The crew may use an ATC radar plot to verify the gross error check. The crew will record the coordinates and the time of the gross error check.

(1) Aircraft Position Check with NAVAIDs. Before entering oceanic airspace, check the aircraft’s position as accurately as possible by using external NAVAIDs to ascertain which aircraft navigation system to use. This may require DME and/or VOR/DME checks to determine navigation system errors through displayed and actual positions.

(2) Updating Navigation the System. In the event of significant discrepancies (greater than 2 NM), consider updating the navigation system. We do not normally recommend updating when the discrepancy is less than 6 NM.

3-6. POSITION PLOTTING. › q. Routine Monitoring. Operators must ensure they have procedures in…

(3) Influential Factors in System Updating. The duration of the flight before the oceanic boundary and the accuracy of the external navigation system are factors that influence any decision to update the system. If the system received an update, follow the proper procedures with the aid of a prepared checklist.

(4) Auto-Coupling. Select the navigation system that performs the most accurately for auto-coupling. In view of the importance of following the correct track in oceanic airspace, some operators advise that the third pilot or equivalent crewmember should check the inserted waypoints using appropriate source information.

l. Oceanic Entry. Crews must ensure they have given an accurate estimated time of arrival (ETA) to ATC for their oceanic entry point. They must also ensure they entered the ocean at the cleared FL.

m. Oceanic Boundary Position Report. Just prior to the oceanic boundary and prior to any waypoint, the crew should monitor, record, and verify the present position coordinates. Check and verify the coordinates for the next waypoint. When the CDU alert light comes on, the crew should note and record the present position on the master document. Verify this information against the current clearance on the master document. Annotate the waypoint number on the master document with the appropriate symbol to indicate its verification. If you make the oceanic boundary position report over a VOR facility, select the appropriate radial to the first oceanic waypoint as a further check shows that the navigation system is tracking according to the current clearance. If DME is available, you can also perform a distance check.

n. Approaching an Oceanic Waypoint. Two minutes before reaching each oceanic waypoint, crews should verify the accuracy of the subsequent waypoint. This verification should include the expected outbound course and distance of the currently effective ATC clearance.

o. At Each Oceanic Waypoint. Crews must ensure that when overhead each oceanic waypoint, the aircraft turns to the anticipated heading and that the distance to the next waypoint is accurate. Verify the coordinates of the next waypoint against the master document. After the ATC position report is sent, plot the present position to ensure that the tracking is correct. The crew should be particularly alert in maintaining SELCAL watch in the event of possible ATC followup to the position watch.

NOTE: Crews must not assume the aircraft has automatically transitioned to the next waypoint.

p. Ten-Minute Position Plotting. Approximately 10 minutes after transitioning each oceanic waypoint, crews will plot their LRNS position and note the coordinates and time on the plotting chart. When sending the ATC position report, copy the coordinates from the master document or the present position and you can read the next two forward positions from the CDU. As soon as the waypoint alert light goes on, check the present position coordinates of each navigation system against the current clearance to ensure that the position report coincides with the actual position of the aircraft and the ATC clearance.

q. Routine Monitoring. Operators must ensure they have procedures in their International Operations Manual concerning which page(s) the PIC will routinely monitor versus the pages the

3-6. POSITION PLOTTING. › w. Navigation in Areas of Magnetic Unreliability (AMU). The FAA…

SIC routinely monitors. For example, the PIC may monitor the cross-track error (XTK) page and the second in command (SIC) may monitor distance/time.

(1) Position Coordinates. There are a number of ways in which you may accidentally disconnect the autopilot (AP) from the command mode. Crews should make regular checks of correct engagement. Although it is a common practice to display “dist/track,” the FAA recommends that the navigation system coupled to the AP display the present position coordinates throughout the flight. If plotting the coordinates at roughly 20-minute intervals, they will confirm that the flight is on track according to the ATC clearance. Distance-to-go information should be available on the instrument panel, and the waypoint alert light provides a reminder of the proximity of the waypoint.

(2) XTK and Track Angle Error (TKE). If a crew makes a position check and verification at each waypoint and 10 minutes after each waypoint, additional plotting every 20 minutes may be counterproductive during routine flight. The navigation equipment not used to steer the aircraft should display XTK and TKE. Monitor these indicators with XTK displayed on the horizontal situation indicator (HSI) when feasible.

r. Use of Radar. Aircraft equipped with airborne weather radar capable of ground mapping should use the radar to observe any land masses as an aid to determining the accuracy of their navigation. The flightcrews must use the radar on a constant basis during flight to monitor navigation system accuracy.

s. Approaching Landfall. When the aircraft is approaching the first landfall NAVAID, it should acquire the appropriate inbound radial as soon as the flightcrew is confident that the NAVAID information is accurate.

t. Navigation System Accuracy Check. At the end of each flight, determine the accuracy of the navigational system to facilitate correction of performance. You may perform a check to determine the radial error at the ramp position as soon as the aircraft parks. Radial errors for INSs in excess of 2 NM per hour are generally considered excessive (part 121, appendix G). Keep records on each individual navigation system performance.

u. Monitoring During Distractions. Training and drills ensure that minor emergencies or interruptions of normal routine do not distract the crew to the extent of mishandling the navigation system. If the AP disconnects during flight, re-engage it carefully to ensure that you follow the correct procedure.

v. Avoiding Confusion Between Magnetic and True. To cover all navigation requirements, some air carriers produce flight plans that include both magnetic and true tracks. If crews are changing to a new system, there is a risk of confusion in selecting the correct values. Operators should devise drills to reduce this risk and ensure that training covers this subject. Crews that check or update their LRNS by reference to VORs located in the Canadian Northern Control Area (NCA) should remember to not align them with reference to magnetic north.

w. Navigation in Areas of Magnetic Unreliability (AMU). The FAA designates Canada’s NCA and Arctic Control Area (ACA) as AMUs. Although Canadian publications sometimes refer to it as the area of compass unreliability, they are the same. The magnetic North

3-6. POSITION PLOTTING. › x. Navigation in Areas of Convergence. Because of the rapid changes in…

Pole is at approximately 75°N 100°W and is slowly moving as it circles the true pole every 960 years. This is why we see current navigation charts occasionally changing an instrument landing system (ILS) course by 1º.

(1) Magnetic North Pole. When you approach the magnetic North Pole, horizontal magnetic influences decrease and vertical magnetic influences increase to a point where the compass is no longer reliable (the magnetic pole is below the aircraft). It is common to see the compass drifting aimlessly or tilting in its case due to the vertical component even when hundreds of miles from the magnetic North Pole. The better the magnetic compass, the closer to the magnetic pole it will operate. Within about 250 miles of the magnetic pole, all aircraft magnetic compasses will be useless. As a result, some VORs, runways, and radar vectors in Canada’s NCA and ACA are oriented to true north.

(2) AMU. When operating in the AMU, move the HDG REF switch to TRUE when the Canada HI 4 chart defines the course with a °T. Add two additional items to the master flight plan checklist: TRUE HDG adjacent to the first true heading leg and MAG HDG at the end of the AMU. This will serve as a reminder to return to a normal heading reference. The primary reason for selecting TRUE HDG in the NCA and ACA is to provide a more realistic navigation display (ND) heading presentation, thus avoiding rapidly changing heading indications. This will help with radar vectors in TRUE and comply with Canadian Air Regulations.

x. Navigation in Areas of Convergence. Because of the rapid changes in variation and due to meridian convergence, you may note a considerable difference between the flight plan course and the flight management computer (FMC) course when conducting the Class II navigation checks. The flight plan entry consists of the average for the leg while the FMC displays the course at the start of the leg. If a significant difference exists between the two, then you can confirm the course by checking it in TRUE, which will eliminate the large changes in variation. In the far north, convergence is so great that even in TRUE there may be a considerable difference between the flight plan and the FMC. If this is the case, check the FMC against the Canada HI 4 chart. The course at the start of the leg on the chart should agree with the FMC. If averaging the outbound and inbound courses of the leg on the Canada HI 4, the result should closely agree with the flight plan.

NOTE: The direct route from Thule to Cambridge Bay in a southwesterly direction begins on a course of 254°T and ends on 219°T. This is a 35° change because of convergence. The variation at Thule is 66°W and the variation at Cambridge Bay is 25°E. This results in a magnetic course of 320°M departing Thule and a 194°M course arriving over Cambridge Bay. This change of 126°M is due to the effects of convergence and variation while flying a great circle route. It is evident that even though the flight in this example is south of 82°N, select a true heading reference, thus allowing a more realistic heading presentation. If this were flown as a single leg, it would be necessary to do the Class II course check using the Canada HI 4 chart as described above in order to get a valid check. The FMC in TRUE should closely agree with the charted outbound course of 254°T and the flight plan should closely agree with the average of 254°T outbound and 219°T inbound, which is 236°T.

3-6. POSITION PLOTTING. › z. ATC ReClearance. Scrutiny groups determined that a reclearance…

y. Weather Deviations. Temporary diversions from track are sometimes necessary, but obtain prior ATC clearance. Such diversions can cause GNEs if you do not re-engage the navigation mode of the AP. Selection of the AP turbulence mode (if applicable) can disengage the AP from the navigation system. After using turbulence mode, fly the aircraft back to the desired track before re-engaging the AP. For inertial platform aircraft, the following steps are useful in preventing GNEs as a result of diversions around severe weather:

• Use the AP turn control knob to turn the aircraft in the desired direction.

• The AP engage switch will automatically move from “command” to “manual.”

• The altitude mode switch will either remain on “altitude hold,” or if in the “altitude select” mode, will trip to “off.”

• Set the steering CDU selector to XTK/TKE to provide a continuous display of cross-track data.

• If encountering turbulence, you may use the “turb” setting on the speed mode selector. In this case, the altitude mode switch automatically positions to “off.”

• Both radio INS switches remain in the INS position. This provides a visual display of the navigation situation on the HSI. Even if more than 8 NM off the track, the pegged needle on the HSI is a reminder of that fact and confirms whether the aircraft is tracking towards, away from, or parallel to the desired track.

• Use the turn control knob to maneuver the aircraft as necessary.

• When clear of the severe weather, steer the aircraft back to the desired track, guided by the steering CDU to zero the XTK indication.

• When the aircraft returns to the desired track, set the AP engage switch to “command” and the altitude mode switch to “altitude hold.” The navigation mode selector should still be in the INS position.

• The captain and first officer, or the entire crew if possible, should monitor the diversion maneuver to ensure that the aircraft has returned to the desired track and if you properly re-engaged the AP for command INS operation.

• After completing return to route, check the assigned Mach number and advise ATC.

z. ATC Re-Clearance. Scrutiny groups determined that a re-clearance scenario is the greatest contributor to an oceanic error (e.g., GNE, Large Height Deviation (LHD)). Experience suggests that when ATC issues a clearance involving rerouting and new waypoints, the risk of error increases. The procedures used to copy the ATC clearance, load and check the waypoints, verify the flight plan information, and prepare a new plotting chart should be the same as the procedures for beginning a flight. Designate one pilot to fly the aircraft while the other pilot reprograms the navigation systems and amends the cockpit documents. In the event that a

3-6. POSITION PLOTTING. › bb. Identifying Faulty Systems.

re-clearance involves a direct routing, retain the data relevant to the original route in case ATC requires the aircraft to return to its original course.

aa. Detecting Failures. Inertial and global positioning system (GPS) installations typically include comparator and/or warning devices, but the crew must still make frequent comparison checks. With three systems onboard, identification of a defective system should be straightforward. Identifying system failures with two systems is more difficult. If a significant deviation occurs in oceanic airspace, contact nearby aircraft on 123.45 MHz and obtain information to aid in identifying a system failure. Maintain and keep a record of GPS or inertial performance available for crews. The following are suggestions for recordkeeping:

• Before takeoff and while stationary, note the inertial groundspeed and position indicators. These may give an indication of system accuracy.

• Note the accuracy of each unit before reaching oceanic airspace, preferably while passing a convenient short-range facility. Make a further record at the destination regarding terminal error after first canceling any in-flight updates made.

• You can make compass deviation checks (inertial only) to determine deviation values for the magnetic compass systems so that you can check the accuracy of the inertial heading outputs in-flight.

bb. Identifying Faulty Systems.

• Check malfunction codes for indications unserviceability.

• Refer to records for indications of prior problems.

• Obtain a fix, possibly using the weather radar, in order to determine position relative to information from other systems.

• Communicate with nearby aircraft on air-to-air VHF to compare information on spot wind, groundspeed, and drift. Compare information from the prognostic chart to the system readout if there is no contact with any aircraft. Use this method as a last resort and preferably should use it with another method of verification.

• Use the heading method (inertial only). Simultaneously read both the inertial and magnetic compass indicators. Obtain the mean to the nearest degree to get an acceptably accurate true heading value to compare to the inertial readings and determine what reading is inaccurate.

• Situations may arise when distance or cross-track differences develop between two LRNSs, but the crew cannot identify the faulty system. If three systems are onboard, accept the two agreeing systems as reliable signals. If, however, only two systems are onboard and they disagree, most operators believe that the best procedure in this instance is to fly the aircraft halfway between the cross-track

Continue reading ↓ 120 of 572 passages shown