AC 90-89A Amateur-Built Aircraft and Ultralight Flight Testing Handbook
Provides suggestions and safety-related recommendations to assist amateur and ultra-light builders in developing individualized aircraft flight test plans. It includes flight testing recommendations for canard-type and ultra-light aircraft. SN 050-007-01087-7
This document is cancelled. It may have been replaced. Check the official source before relying on it.
U.S. Department
of Transportation
Federal Aviation Administration
Advisory Circular
Initiated by: AFS-340
DATE: 5/24/95
AC NO: 90-89A
AMATEUR-BUILT AIRCRAFT AND ULTRALIGHT
FLIGHT TESTING HANDBOOK
U.S. Department
of Transportation
Federal Aviation Administration
Advisory Circular
FLIGHT TESTING HANDBOOK
i
Subject: AMATEUR-BUILT AIRCRAFT Date: 5/24/95 AC No: 90-89A & ULTRALIGHT FLIGHT Initiated by: AFS-340 Change: TESTING HANDBOOK
1. PURPOSE. This advisory circular (AC) sets forth suggestions and safety related recommendations to assist amateur and ultralight builders in developing individualized aircraft flight test plans.
2. CANCELLATION. AC 90-89, Amateur- Built Aircraft Flight Testing Handbook, dated September 18, 1989, is cancelled.
3. RELATED READING MATERIAL. A list of selected reading material on amateur-built/ ultralight flight testing and first flight experience may be found in appendix 3.
4. BACKGROUND.
a. The Federal Aviation Administration (FAA), the Experimental Aircraft Association (EAA), and the United States Ultralight Association (USUA) are concerned and committed to improving the safety record of amateur-built and ultralight aircraft.
b. The FAA Administrator, T. Allen McArtor, and EAA President, Paul H. Poberezny, signed a Memorandum of Agreement on August 1, 1988, which addressed the need for educational and safety programs to assist amateur-builders in test flying their aircraft. In accordance with that agreement, this AC provides guidelines for flight testing amateurbuilt aircraft.
c. As part of the FAA’s continuing efforts to improve the safety record of all types of general aviation aircraft, this AC has been revised to include flight testing recommendations for canard-type and ultralight aircraft.
5. DEFINITIONS. The following terms are defined for use in this AC.
a. Amateur-built aircraft means an aircraft issued an Experimental Airworthiness Certificate under the provisions of Federal Aviation Regulations (FAR) § 21.191 (g).
b. The term ultralight means a vehicle that meets the requirements of FAR § 103.1.
c. The term ultralight in this AC also means a two-place training vehicle of 496 pounds or less, operating under an EAA or USUA exemption to FAR Part 103.
d. For the purpose of this AC, both an amateur-built aircraft and a ultralight vehicle will be referred to as an ‘‘aircraft.’’
6. DISCUSSION.
a. This AC’s purpose is the following:
(1) To make amateur-built/ultralight aircraft pilots aware that test flying an aircraft is a critical undertaking, which should be approached with thorough planning, skill, and common sense.
(2) To provide recommendations and suggestions that can be combined with other sources on test flying (e.g., the aircraft plan/kit manufacturer’s flight testing instructions, other flight testing data). This will assist the amateur/ultralight owner to develop a detailed flight test plan, tailored for their aircraft and resources.
ii
AC 90-89A 5/24/95
b. The flight test plan is the heart of all professional flight testing. The plan should account for every hour spent in the flight test phase and should be adhered to with the same respect for the unknown that all successful test pilots share. The time allotted for each phase of a personalized flight test plan may vary, and each phase may have more events or checks than suggested in this AC. The goals, however, should be the same.
c. The two goals for an amateur builder/ ultralight owner should be as follows:
(1) At the end of the aircraft’s flight test phase, the aircraft will have been adequately tested and found airworthy and safe to operate within its established operational envelope.
(2) Incorporation of the flight test operational and performance data into the aircraft’s flight manual so the pilot can reference the data prior to each flight.
7. REQUEST FOR INFORMATION.
a. This AC is designed as a reference document to assist in preparing a flight test plan for an amateur-built or ultralight aircraft.
(1) The suggestions and recommendations in chapters 1 through 6 are for conventionallydesigned aircraft with an air-cooled, 4-cycle, reciprocating engine that develops less than 200 horsepower with a fixed pitch propeller.
(2) Chapter 7 deals with flight testing recommendations for canard aircraft.
(3) Chapters 8 through 10 address flight testing considerations for ultralight vehicles under FAR Part 103 and two-seat ultralight training
vehicles of less than 496 pounds empty weight operating under an exemption to FAR Part 103.
b. Because of the large number of existing amateur-built/ultralight aircraft designs and new designs being introduced each year, the FAA encourages public participation in updating this document. Send comments, suggestions, or information about this AC to the following address:
U.S. Department of Transportation Federal Aviation Administration Flight Standards Service (AFS-340) 800 Independence Ave, SW. Washington, DC 20591
c. Suggestions also may be sent to AFS-340 by FAX (202) 267-5115.
d. After a review, appropriate comments, suggestions, and information may be included in the next revision of this AC.
8. TO OBTAIN COPIES OF THIS AC. Order AC 90-89A from:
U.S. Department of Transportation Property Use and Storage Section, M-45.3 Washington, DC 20590.
William J. White Deputy Director, Flight Standards Service
iii
THIS PAGE IS INTENTIONALLY LEFT BLANK, SO THAT THE TOC CAN BE ON PAGE iii
PER PLACEMENT IN DOCUMENT.
iv
THIS PAGE IS INTENTIONALLY LEFT BLANK, SO THAT THE TOC CAN BE ON PAGE iii
PER PLACEMENT IN DOCUMENT.
CONTENTS
Page
CHAPTER 1. PREPARATION
CHAPTER 1. PREPARATION
Section 1. Homework … 1 Section 2. Airport Selection … 2 Figure 1 - Runway Length Chart … 3 Section 3. Emergency Plans and Equipment … 4 Section 4. Test Pilot … 6 Section 5. Medical Facts For Pilots … 7 Section 6. Transporting The Aircraft To the Airport … 9 Section 7. Assembly and Airworthiness Inspection … 10 Section 8. Weight and Balance … 14 Figure 2 - Empty Weight CG … 15 Figure 3 - Take Off CG … 16 Figure 4 - Additional Equipment Added … 17 Section 9. Paperwork … 18 Section 10. Powerplant Tests … 19 Section 11. Additional Engine Tests … 22 Section 12. Propeller Inspection … 25 Figure 5 - Propeller Tracking … 26
CHAPTER 2. TAXI TESTS
CHAPTER 2. TAXI TESTS
Section 1. Low Speed Taxi Tests … 29 Section 2. High Speed Taxi Tests … 30
CHAPTER 3. THE FIRST FLIGHT
Section 1. General … 33 Section 2. The Role of the Chase Plane … 34 Section 3. Emergency Procedures … 35 Section 4. First Flight … 36 Section 5. First Flight Procedures … 37
CHAPTER 4. THE FIRST 10 HOURS
CHAPTER 4. THE FIRST 10 HOURS
Section 1. The Second Flight … 41 Section 2. The Third Flight … 41 Section 3. Hours 4 through 10 … 41
CHAPTER 5. EXPANDING THE ENVELOPE
Section 1. General … 45 Section 2. Hours 11 through 20 … 45
v
Figure 6 - Climb Airspeed and Altitude Graph … 47 Figure 7 - Best Rate of Climb Speed Graph … 48 Section 3. Hours 21 through 35: Stability and Control Checks … 49 Figure 8 - Static Stability … 49 Figure 9 - Time … 50 Section 4. A Word or Two About Flutter … 52
Section 1. General … 45 Section 2. Hours 11 through 20 … 45
vi
CONTENTS—Continued
Page
Section 5. Spins … 54 Section 6. Accelerated Stalls … 56
CHAPTER 6. PUTTING IT ALL TOGETHER: 36 HOURS TO ———?
Section 1. Maximum Gross Weight Tests … 57 Section 2. Service Ceiling Tests … 58 Section 3. Navigation, Fuel Consumption, and Night Flying … 59
CHAPTER 7. THOUGHTS ON TESTING CANARD TYPE AMATEUR-BUILT AIRCRAFT
CHAPTER 7. THOUGHTS ON TESTING CANARD TYPE AMATEUR-BUILT AIRCRAFT
Section 1. Canards … 63
CHAPTER 8. ULTRALIGHT AIRFRAME INSPECTION
Section 1. Differences … 67 Section 2. The Test Pilot … 68 Section 3. Pre-flight Airframe Inspection … 68
CHAPTER 9. ULTRALIGHT ENGINE/FUEL SYSTEM INSPECTION
Section 1. Engine Inspection … 71 Section 2. Fuel Systems … 72
Section 1. Engine Inspection … 71 Section 2. Fuel Systems … 72
CHAPTER 10. ULTRALIGHT TEST FLYING RECOMMENDATIONS
Section 1. Three Recommendations … 75 Section 2. Airport Selection … 75 Section 3. Taxiing … 76 Section 4. First Flight Differences … 76 Section 5. Emergency Procedures … 77
Appendix 1. Sample Checklist for a Condition Inspection …
Appendix 1. Sample Checklist for a Condition Inspection …
(7 pages) … 1
Appendix 2. Addresses for Accident/Incident Information …
(1 page) … 1
Appendix 3. Additional References on Flight Testing …
(4 pages) … 1
1
CHAPTER 1. PREPARATION
‘‘The Laws of Aerodynamics are unforgiving and the ground is hard.’’ Michael Collins (1987)
SECTION 1. HOMEWORK
SECTION 1. HOMEWORK
‘‘If you have no plan--you have no goal.’’ Harold Little, Aircraft Manufacturer (1994)
1. OBJECTIVE. A planned approach to flight testing.
a. The most important task for an amateurbuilder is to develop a comprehensive FLIGHT TEST PLAN. This PLAN should be individually tailored to define the aircraft’s specific level of performance. It is therefore important that the entire
flight test plan be developed and completed BEFORE the aircraft’s first flight.
b. The objective of a FLIGHT TEST PLAN is to determine the aircraft’s controllability throughout all the maneuvers and to detect any hazardous operating characteristics or design features. This data should be used in developing a FLIGHT MANUAL that specifies the aircraft’s performance and defines its operating envelope.
2
SECTION 2. AIRPORT SELECTION
SECTION 2. AIRPORT SELECTION
‘‘An airport should be chosen with the same care and consideration as getting a second doctor’s opinion.’’
Fred Wimberly, EAA Flight Test Advisor (1994)
1. OBJECTIVE. To select an airport to test fly the aircraft.
a. The airport should have one runway aligned into the prevailing wind with no obstructions on the approach or departure end. Hard surface runways should be in good repair and well maintained to avoid foreign object damage (FOD) to the propeller and landing gear. Grass fields should be level with good drainage. Avoid airports in densely populated or developed areas and those with high rates of air traffic. The runway should have the proper markings with a windsock or other wind direction indicator nearby.
b. To determine an appropriate runway, use the chart in figure 1 (sea-level elevation), or the following rule-of-thumb:
c. The ideal runway at sea-level elevation should be at least 4,000 feet long and 100 feet wide. For each 1,000 feet increase in field elevation, add 500 feet to the runway length. If testing a high performance aircraft, the airport’s runway at sealevel should be more than 6,000 feet long and 150 feet wide to allow a wider margin of safety. Other considerations, such as power to weight ratio, wing design, and density altitude, also should be factored into the equation for picking the best runway for the initial flight testing.
3
Take-off Distance in Feet
FIGURE 1. Runway Length Chart
d. Identify emergency landing fields located within gliding distance from anywhere in the airport pattern altitude. Since engine failures are second only to pilot error as the major cause of amateur-built aircraft accidents, preparations for this type of emergency should be a mandatory part of the FLIGHT TEST PLAN.
e. It is advisable to perform flight tests from an airport with an active unicom or tower, even if the aircraft does not have an electrical system or is not equipped with a radio. Even at an uncontrolled field, a communications base should be improvised. For both situations, a hand held radio with aviation frequencies and a headset with a mike and a pushto-talk switch on the stick/yoke is recommended. Good radio communications improves the overall level of safety and reduces cockpit workload.
f. The FAA recommends airport selection criteria include the availability of hangar space and ramp areas. These facilities will provide protection from inclement weather and vandalism while the aircraft is being tested, maintained, and inspected.
g. The airport should have a telephone and fire fighting equipment, the latter being in compliance with relevant municipal codes (e.g., fire codes).
h. Explain the Flight Test Program and EMERGENCY PLANS to the airport manager or owner. They may be able to assist the amateurbuilder in obtaining temporary hangar space, providing ground/air communications, and supplying emergency equipment for use during the flight test.
4
SECTION 3. EMERGENCY PLANS AND EQUIPMENT
SECTION 3. EMERGENCY PLANS AND EQUIPMENT
‘‘The object of the game, gentlemen, is not to cheat death: the object is not to let him play.’’ Patrick
Poteen, Sgt. U.S. Army
1. OBJECTIVE. To develop a FLIGHT TEST PLAN which contain two sets of emergency plans; one for IN-FLIGHT emergencies and another for GROUND emergencies.
a. The IN-FLIGHT emergency plan should address the following:
(1) Complete engine failure or partial failure, especially after take off
(2) Flight control problems and severe outof-rig conditions
(3) Fire in the engine compartment or cockpit
b. The GROUND EMERGENCY plan should be developed to train the ground crew and/or the airport fire department crash crew on the following:
(1) The airplane canopy or cabin door latching mechanism
(2) The pilot’s shoulder harness/seat belt release procedure
(3) The location and operation of the fuel shut-off valve
(4) The master switch and magneto/ignition switch location and OFF position
(5) Engine cowling removal procedures to gain access to the battery location or for fire fighting
(6) The battery location and disconnect procedures
(7) Fire extinguisher application and use
(8) How to secure the ballistic parachute system
c. Ground Crew. Every test of an amateurbuilt aircraft should be supported by a minimum ground crew of two experienced individuals. The ground crew’s function is two-fold:
5
(1) To ensure that the aircraft is in airworthy condition for safe operation
(2) To provide assistance to the test pilot in an emergency
d. The Airport.
(1) If the airport does not have a fire rescue unit, it is suggested the ground crew have a four wheel drive vehicle equipped with a portable radio, first aid kit, metal-cutting tools, and a fire extinguisher. A minimum of one person should be trained in first-aid.
(2) If the airport provides a fire rescue unit, the test pilot should ensure the rescue unit and the ground crew are trained and competent in performing ground emergency functions as identified in the FLIGHT TEST PLAN.
(3) Suggestion. For a small donation, some local volunteer fire and rescue companies will provide the amateur-builder with a standby crew during the initial critical portions of the flight test phase.
e. Hospital Location. The ground crew should know the location and telephone numbers of the hospitals and fire rescue squads in the vicinity of the airport AND the flight test area. If the test pilot is allergic to specific medications, or has a rare blood type, a medical alert bracelet or card should be carried or worn to alert medical personnel of the condition.
f. Fire Extinguisher. Fire extinguisher’s should be available to the ground crew, and a fire extinguisher should be securely mounted in the cockpit within easy reach of the test pilot. A fire axe, or other tool capable of cutting through the canopy, also should be positioned in the cockpit.
g. Fire Protection. There is always danger of a flash fire during test flights. To prevent burns, the pilot should wear an aviation/motorcycle helmet, NOMEX coveralls/gloves and smoke goggles. If NOMEX clothing is not available, cotton or wool clothing will offer some protection from heat and flames. Pilots should never wear nylon or polyester clothing because synthetic materials melt when exposed to heat and will stick to the skin.
h. Pilot Protection. A modern aviation/motorcycle helmet, a properly installed shoulder harness, a well designed seat, a clean cockpit design free of
protruding components/sharp edges, NOMEX clothing, smoke goggles, and a memorized emergency plan ensure safety during flight testing.
i. Parachute. The decision to wear a parachute depends on the type of aircraft being tested. Some aircraft have forward hinged canopies that are not equipped with quick release pins or have pusher propellers which increase the chance of injury to the pilot while exiting the aircraft. Other aircraft designs may pose no exit problems. If the decision is made to wear a parachute, check that it has been recently packed (within 120 days) by a qualified parachute rigger. Ensure that the chute has not been exposed to rain/moisture and when worn, does not interfere with cockpit management. The test pilot should be thoroughly trained on how to exit the aircraft and deploy the parachute.
j. Ballistic Chutes. Ballistic chutes are the latest development in dealing with in-flight emergencies. A ballistic chute is attached to the aircraft and when activated, lowers the whole aircraft and the pilot to the ground at the rate of descent of approximately 20 feet per second.
(1) Deployment Scenarios:
(i) structural failure
(ii) mid-air collision
(iii) stall/spin
(iv) loss of control/icing
(v) engine failure over bad terrain
(vi) pilot incapacitation
(2) Installation Considerations: The builder should consider the following when installing a ballistic chute:
(i) Matching the chute with the aircraft’s size, weight, and Vne speed (check with the chute manufacturer)
(ii) How the chute will be positioned and mounted
(iii) The chute’s effect on the aircraft’s weight and balance before deployment and aircraft’s touchdown attitude after deployment
(iv) Compatibility of the opening loads and the aircraft’s structural design limits
6
(v) The routing of the bridle and
harness
(vi) The routing of the activating housing
(vii) The placement of the activating handle in the cockpit
(viii) Incorporation of chute deployment procedures in the in-flight emergency plan and emergency check list
(ix) The deployment time, from activation to full chute opening
(3) If a ballistic chute is installed, the builder should add the appropriate ballistic chute inspection items to the aircraft’s pre-flight inspection check list. The builder also should add the ballistic chute manufacturer’s repack/refitting schedule and maintenance inspections to the flight manual and the conditional annual inspection check list.
SECTION 4. TEST PILOT
SECTION 4. TEST PILOT
‘‘We are looking for a few good Men and Women!’’ Marine Corps advertisement (1991)
1. OBJECTIVE. To select a qualified individual to be the test pilot.
2. GENERAL. The test pilot should be competent in an aircraft of similar configuration, size, weight, and performance as the aircraft to be tested. If the aircraft’s builder is the test pilot, the costs involved in maintaining pilot competence should be budgeted with the same level of commitment and priority that is assigned to plans and materials to complete the project.
3. TEST PILOT REQUIREMENTS.
a. A test pilot should meet the following minimum qualifications:
(1) Physically fit: Test flying an aircraft is a stressful and strenuous task
(2) No alcohol or drugs in the last 24 hours
(3) Rated, current, and competent in the same category and class as the aircraft being tested
(4) Current medical and biennial or flight review as appropriate, or a current USUA certification and flight review
b. Suggested Test Pilot Flight Time Requirements. The following suggested number of flight hours are only an indication of pilot skill, not an indicator of pilot competence. Each test pilot must assess if their level of competence is adequate or if additional flight training is necessary. If an individual determines they are not qualified to flight test
an unproven aircraft, someone who is qualified must be found.
(1) 100 hours solo time before flight testing a kit plane or an aircraft built from a time-proven set of plans
(2) 200 hours solo time before flight testing for a ‘‘one of a kind’’ or a high performance aircraft
(3) A minimum of 50 recent takeoffs and landings in a conventional (tail wheel aircraft) if the aircraft to be tested is a tail dragger
c. The test pilot should:
(1) Be familiar with the airport and the emergency fields in the area
(2) Talk with and, if possible, fly with a pilot in the same kind of aircraft to be tested
(3) Take additional instruction in similar type certificated aircraft. For example, if the aircraft to be tested is a tail dragger, a Bellanca Citabria or Super Cub is appropriate for training. For testing an aircraft with a short wing span, the Grumman American Yankee or Globe Swift is suitable for training.
(4) Be considered competent when they have demonstrated a high level of skill in all planned flight test maneuvers in an aircraft with performance characteristics similar to the test aircraft
7
(5) Study the ground and in-flight emergency procedures developed for the aircraft and practice them in aircraft with similar flight characteristics
(6) Have logged a minimum of 1 hour of training in recovery from unusual attitudes within 45 days of the first test flight
(7) If appropriate, have logged a minimum of 10 tail wheel take-off and landings within the past 30 days
(8) Study the performance characteristics of the aircraft to be tested. Refer to the designer’s or kit manufacturer’s instructions, articles written by builders of the same make and model aircraft, and study actual or video tape demonstrations of the aircraft.
(9) Review the FAA/National Transportation Safety Board (NTSB)/EAA accident reports for the same make and model aircraft to be aware of problems the aircraft has experienced during previous operations (see appendix 2 for the address).
(10) Memorize the cockpit flight controls, switches, valves, and instruments. A thorough knowledge of the cockpit will result in controlled and coordinated mental and physical reactions during emergencies.
NOTE: The EAA has developed a Flight Advisor Program which offers builders/ pilots assistance in performing a self evaluation of the flight test program and/or selection of the test pilot. To obtain additional information, contact a local EAA Chapter or EAA Headquarters, (414) 426-4800.
SECTION 5. MEDICAL FACTS FOR PILOTS
SECTION 5. MEDICAL FACTS FOR PILOTS
‘‘If the pilot is unairworthy, so is the airplane!’’ Bill Chana, Aeronautical Engineer
1. OBJECTIVE. To identify some of the well known medical causes for aircraft accidents and to stress the importance of a personal pre-flight checklist in addition to an aircraft pre-flight checklist.
a. Alcohol. FAR Part 91, ‘‘General Operating and Flight Rules,’’ § 91.17 requires that 8 hours must elapse from the last drink to the first flight. Test flying an aircraft, however, places additional mental and physical demands on the pilot. The FAA strongly recommends a minimum of 24 hours between the last drink and the test flight. This is because small amounts of alcohol in the blood stream can affect judgement, reaction time, and decrease a pilot’s tolerance to hypoxia.
b. Anesthetics. Local and dental anesthetic can affect a pilots performance in many adverse ways. It is recommended that a minimum of 48 hours elapse from the time of anesthesia to the time the pilot climbs into the cockpit.
c. Blood Donations. Do not fly for 3 weeks after donating blood. The body needs approximately three weeks for a complete physiological recovery. Although the physical affects may not be noticeable at sea level, they will become apparent when flying at higher altitudes.
d. Carbon Monoxide (CO). CO is a colorless, odorless, tasteless gas that is always present in engine exhaust fumes. Carbon monoxide prevents oxygen absorption by the blood, and exposure to the gas creates vision problems, headaches, disorientation, and blurred thinking (see chapter 1, section 7, paragraph 3 (g) for testing the aircraft for CO contamination).
e. Drugs. Similar to alcohol, drugs will reduce or impair judgement and affect reflexes and hand/ eye coordination. It is a given that the use/abuse of illegal drugs is dangerous and against the law. Prescription drugs and over-the-counter remedies, however, also may be dangerous when combined with flying. The FAA recommends all pilots who must take medication consult with an Aviation Medical Examiner (AME) to understand the medication’s affects on their ability to think and react while in the cockpit.
f. Ear and Sinus Pain.
(1) Ear and sinus pain is usually caused by the eardrum or sinuses failing to equalize the air pressure during a descent. The blocked ears and sinuses can be caused by a head cold. The pain can be considerable and is most noticeable during
8
descents. For ear blockages try yawning, swallowing, or chewing gum which may give some relief. The Valsalva procedure can be effective: pinch the nose, close the mouth, and try to force air through the nostrils.
(2) If ear blockage occurs during flight, try climbing back to a higher altitude (lower air pressure) until the pain lessens. Then begin a gradual rate of descent, allowing the ears and sinuses time to adapt to the increasing pressure.
(3) After landing, nasal sprays will give some sinus pain relief. To relieve ear pain, try wetting paper towels with hot water, put the towels in the bottom of a plastic or dixie cup and then hold the cups over the ears. The warmth will help ease the inflamed tissues and reduce the pain. If pain continues, see a doctor.
NOTE: The best way to avoid this problem is not to fly with a head cold, upper respiratory infection, or nasal allergic condition. Be advised that some nasal and oral decongestants could be ineffective at altitude and have side effects such as drowsiness that can significantly impair pilot performance. Again, consult with an Aviation Medical Examiner to understand the affects of medication before flying.
g. Fatigue. Fly only when healthy, fit, and alert. Mental and physical fatigue will generally slow down a pilot’s reaction time, affect decision making, and attention span. Lack of sleep is the most common
cause of fatigue, but family and business problems can create mental fatigue which can have the same effects on the pilot as lack of sleep.
h. Flicker Vertigo. Light, when flashing at a frequency between 4 to 29 cycles per second, can cause a dangerous physiological condition in some people called flicker vertigo. These conditions range from nausea and dizziness to unconsciousness, or even reactions similar to an epileptic fit. When heading into the sun, a propeller cutting the light may produce this flashing effect. Avoid flicker vertigo, especially when the engine is throttled back for landing. To alleviate this when the propeller is causing the problem, frequently change engine revolutions per minute (rpm). When flying at night and the rotating beacon is creating flicker vertigo, turn it off.
i. Underwater Diving. Never fly immediately after SCUBA diving. Always allow 24 hours to elapse before flying as a pilot or a passenger in order to give the body sufficient time to rid itself of excessive nitrogen absorbed during diving.
j. Stress. Stress from the pressures of a job and everyday living can impair a pilot’s performance, often in subtle ways. A test pilot may further increase the stress level by setting unreasonable test flying schedules in order to meet an arbitrary ‘‘be done by date.’’ Stress also may impair judgement, inducing the pilot to take unwarranted risks, such as flying into deteriorating weather conditions or flying when fatigued to meet a self imposed deadline.
9
SECTION 6. TRANSPORTING THE AIRCRAFT TO THE AIRPORT
SECTION 6. TRANSPORTING THE AIRCRAFT TO THE AIRPORT
‘‘Best laid plans of mice and men are often stuck in traffic.’’ Ben Owen, EAA Executive Director (1994)
1. OBJECTIVE. To reduce damaging the aircraft in transit. The following suggestions may prevent this from happening:
a. Use a truck or flat bed truck/trailer large enough to accommodate the aircraft and the additional support equipment.
b. If the aircraft wings are removable, build padded jigs, cradles, or fixtures to hold and support them during the trip to the airport.
c. Secure the fixtures to the truck/trailer, then secure the wings to the fixture.
d. Use two or more ropes at each tie down point.
e. Use heavy moving pads used for household moves to protect wings and fuselage. Most rent-atruck firms offer them for rental.
f. During the planning stage, obtain applicable permits and follow the local ordinances for transporting an oversized load. Ask the local police if they can provide an escort to the airport.
g. Brief the moving crew thoroughly before loading and unloading the aircraft.
h. Ensure the designated driver has recent experience driving a truck/trailer and is familiar with the roads to the airport.
10
SECTION 7. ASSEMBLY AND AIRWORTHINESS INSPECTION
‘‘Complacency is one of the major causes of accidents, no matter how well things are going, something
can go wrong’’ Art Scholl
SECTION 7. ASSEMBLY AND AIRWORTHINESS INSPECTION
1. OBJECTIVE. To determine the airworthiness of the aircraft and its systems.
2. GENERAL.
a. If the aircraft must be reassembled after being moved to the airport -- take time to do so carefully. This is a critical event because mistakes can easily be made due to the builder’s preoccupation with the impending first flight of the aircraft. One of the most common and deadly mistakes is to reverse the rigging on the ailerons. To prevent errors in reassembling the aircraft, follow the designer’s or kit manufacturer’s instructions, or use a written check list specifically designed as part of the FLIGHT TEST PLAN. At the completion of each major operation, have another expert check the work.
b. When the aircraft is reassembled, perform a pre-flight ‘‘fitness inspection.’’ This inspection should be similar in scope and detail to an annual inspection. The fitness inspection should be accom-
plished even if the aircraft has just been issued a special airworthiness certificate by the FAA. Even if a builder was 99 percent perfect and performed 10,000 tasks building the aircraft, there would still be a hundred items that would need to be found and corrected before the first flight.
3. FITNESS INSPECTION - AIRFRAME. The following additional safety check list items may not be applicable to all amateur-built make and model aircraft, but are presented for consideration and review:
a. Control stick/wheel: The control stick/ wheel should have a free and smooth operation throughout its full range of travel. There should be no binding or contact with the sides of the fuselage, seat, or instrument panel. There should be no freeplay (slack) in the controls, nor should the controls be tight as to have stick-slip movement.
11
b. Rudder pedals: Move the rudder pedals through the full range of travel. The pedal movement should be smooth with no binding. The test pilot should ensure that their shoes will not catch on exposed metal lines, fixtures, or electrical wire harness.
c. Brakes: Hand and/or toe brake pressure should be firm with no tendency to bleed down or lock up. Spongy brakes that must be ‘‘pumped up,’’ or show a drop in the level of brake fluid in the reservoir after a few brake applications, indicate a brake fluid or air leak in the system.
d. Main landing gear: Ensure that the gear attach points, shimmy dampener, bungees, wheels, brakes, and wheel fairings are airworthy. If applicable, check that the tail wheel pivot point is centered and vertical in relation to the longitudinal axis of the aircraft. It is critical that the main landing gear alignment toe in/toe out is zero or matches the specifications for fuselage/landing gear alignment called out in the plans. Even one landing gear wheel out of alignment can cause a ground loop.
e. Control surfaces: Perform rigging checks to ensure that control input for ailerons, rudder, elevators, and trim tabs results in the correct amount of travel and direction of the control movement and that contact with the stops is made. Also ensure that the flaps, if installed, have the proper travel, operate as a single unit, and cannot be extended beyond the maximum extended position. It is important to ensure that the control cable tension is correct by checking it with a calibrated tensiometer and confirming that all the attachment hardware is secured and safetywired.
(1) If the cable tension is less than the specifications require, the ‘‘in flight’’ air loads during flight will prevent full travel of the control, even if the control has the right amount of deflection and hits all the stops in the cockpit/wing/tail when tested on the ground. With low cable tension, the desired control movement input will be absorbed by the slack in the cables.
(2) While checking cable tension, make sure there is no ‘‘free play’’ in the flight control hinges and rod ends. Free play and loose cable tension combined with control mass imbalance sets the stage for the onset of control surface ‘‘flutter.’’ Do not, however, rig the controls at too high a cable
tension. This will cause high wear rate on the pulleys and prevent good control feel, especially at low airspeeds.
f. Instrument panel: All the instruments should be properly secured in the panel and have preliminary markings on them. Airspeed indicator and engine tachometer should be marked with the EXPECTED performance range markings. Oil temperature and oil pressure must have the engine manufacturer’s recommended operating range marked. If the markings are on the instrument glass face, paint a white slippage mark on both the glass and on the instrument case to alert the pilot in case the glass/range marks have moved. Attach a temporary placard to the instrument panel with the expected stall, climb, and glide speeds. It is a handy reference in times of emergency.
g. Behind the instrument panel: Very few amateur-built aircraft of the same make and model have the same instrument panel design. Each amateur-builder should inspect this area to ensure that all line connections are tight, that nothing interferes with control travel, and there are no loose wires or fuel, oil, or hydraulic leaks.
h. Carbon Monoxide: Carbon Monoxide leaks also can be performed. Wait until night or put the aircraft in a dark hangar. Climb into the cockpit and have a friend shine a bright flood light close to the fire-wall. If light leaks into the cockpit, carbon monoxide can seep in. Mark it and seal it.
i. Engine and propeller controls: All controls should be visually inspected, positive in operation, and securely mounted. The friction lock on both controls should be checked for operation. Each control should have full movement with at least a 1⁄4 inch of ‘‘cushion’’ at the full travel position. The control cables should be firmly attached to the fuselage along each 24 inches of their runs to prevent whipping of the cable and loss of cable movement at the other end. Control cables with ball sockets should have large area washers on either end of the bolt connection. This will ensure the control will remain connected, even if the ball socket fails and drops out.
j. Static system: The best procedure to check the altimeter for leaks and accuracy is to have the entire static system checked in accordance with FAR Part 43, appendix E, at an FAA-approved repair station.
12
4. FIELD CHECK. Two people are needed to accomplish the following field check that will enable an amateur-builder to detect if the aircraft’s instrument system is leaking: (Note: This field check is not an accuracy check.)
a. Airspeed check: Slip a long rubber hose over the pitot mast (surgical tubing is recommended). As one person reads the airspeed, the other should very slowly roll up the other end of the tubing. This will apply pressure to the instrument. When the airspeed indicator needle reaches the aircraft’s approximate recommended cruise speed, pinch the hose shut, and hold that reading. The airspeed needle should remain steady for a minute if the system is sound. A fast drop off will indicate a leak in the instrument, fittings, lines, or the test hose attachment. NEVER force air in the pitot tube or orally apply suction on a static vent. This will cause damage to the instruments.
b. Altimeter/vertical speed check.
(1) To check the static side, apply low suction at the end of the static vent port. The easiest way to gain access to the static system is to remove the static line at the static port. If there are two static ports, tape the unused port closed. Next, get two feet of surgical tubing, seal one end, and tightly roll it up. Attach the open end to the static line and slowly unroll the tubing. This will apply a suction, or low pressure, to the static system.
(2) The altimeter should start to show an increase in altitude. The vertical speed indicator also should indicate a rate of climb. The airspeed may show a small positive indication. When the altimeter reads approximately 2,000 feet, stop and pinch off the tube. There will be some initial decrease in altitude and the vertical speed will read zero. The altimeter should then hold the indicated altitude for at least a minute. If altitude is lost, check for leaks.
(3) IMPORTANT: The above airspeed and altimeter field checks should not be considered the equivalent of airspeed or static system accuracy tests as certified by a certificated repair station, but a check of the system for possible leaks. These checks do not take into consideration the pitot tube and static ports located on the airframe. The FAA recommends the builder not deviate from the designer’s original plans when installing the pitot and static system.
c. Fuel system: Since 1983, more than 70 percent of the engine failures in amateur-built aircraft were caused by fuel system problems. Many times the direct cause of engine failure was dirt and debris in the fuel tank and lines left behind during the manufacturing process.
(1) Before the aircraft’s fuel tanks are filled, the amateur-builder should vacuum any manufacturing debris from each tank and wipe them down with a ‘‘tack’’ cloth (available from a paint supply store). Next, the system should be flushed with aviation grade gasoline several times in order to remove any small or hard to reach debris from the tanks and lines. The fuel filter/gasolator screen/carburetor finger screen should also be cleaned. The amount of time spent ‘‘sanitizing’’ the fuel system will provide big safety dividends for the life of the aircraft.
(2) When filling the tanks, place the aircraft in the straight and level cruise position. Add fuel in measured amounts to calibrate the fuel tank indicators. While allowing the aircraft to sit for a short time to observe for possible leaks, inspect the fuel tank vents to see if they are open and clear. Check that the fuel tank caps seal properly. If there are no leaks and the fuel system has an electric boost pump, pressurize the system and again check for leaks. The fuel selector, vents and fuel drains should be properly marked and tested for proper operation.
NOTE: Many amateur-built aircraft take 5 to 8 years to build. During that time, many rubber-based oil and fuel lines and cork gaskets that were installed early in the building process may have age hardened, cracked, and/or turned brittle. The builder should carefully inspect these components and replace as necessary to prevent a premature engine failure.
d. Hydraulic system: The hydraulic system should function dependably and positively in accordance with the designer’s intent. Retractable landing gear should be rigorously cycled on the ground, using both the normal and emergency landing gear extension system.
e. Safety belt and shoulder harness: These items should be checked for condition and proper installation. A review of amateur-built aircraft accidents has disclosed a significant number of accidents in which the seat belt mounting hard points
13
failed. Each seat belt and shoulder harness mounting hard point should be built to the designer’s specifications to ensure that it will hold the harness and pilot in the aircraft at the ultimate design ‘‘G’’ load specification, both positive and negative, for the aircraft.
f. Avionics and electrical checks: Test the avionics systems. Perform an operational check to ensure the radio(s) transmit and receive on all frequencies. Inspect circuit breakers/fuses, microphones, and antennas for security and operation. Test the ELT for proper operation and battery life. Electrical systems can be checked for operation of lights, instruments, and basic nav/comm performance. Other electrical systems, such as generator/alternator output can be checked during the engine run-ins, taxi, and flight tests. Check the battery and the battery compartment for security and if applicable, ensure
that the battery is properly vented to the outside of the aircraft. Check the condition of the engine to airframe bonding (grounding) wire. Ensure that all electrical instruments operate properly.
g. Cowling and panel checks: Ensure that all inspection panels are in place, the cowling is secured, and cowl flap operation is satisfactory. Inspect the propeller spinner and its backing plate for cracks.
h. Canopy/door locks checks: Ensure the canopy or doors on the aircraft work as advertised. Double check the canopy or door lock(s) so the canopy and doors will not open in flight and disturb the airflow over the wings and stall the aircraft. If a canopy jettison system is installed, check for proper operation when the aircraft on the ground and when it is on jacks. (Jacks will simulate flight loads on the aircraft.)
14
SECTION 8. WEIGHT AND BALANCE
SECTION 8. WEIGHT AND BALANCE
‘‘Never argue with your spouse or a mathematician’’ Phil Larsh, Accident Prevention Counselor,
Colfax IN (1994)
1. OBJECTIVE. To discuss the importance of developing an accurate weight and balance calculations for both test and recreational flights. Additional information on weight and balance can be found in AC 91-23A, Pilot’s Weight and Balance Handbook.
a. A good weight and balance calculation is the keystone of flight testing. Accurately determining the aircraft’s take-off weight and ensuring that the center of gravity (CG) is within the aircraft’s design
for each flight is critical to conducting a safe flight test.
b. An aircraft should be level when weighed, spanwise and fore and aft in accordance with the manufacturer’s instructions, and should be in the level flight position. It is highly recommended that the weighing be done in an enclosed area, using three calibrated scales. Bathroom scales are not recommended because they are not always accurate.
15
ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)
ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)
Left Wheel
Right Wheel
Tail Wheel
TOTALS
101
99
42
242
60
60
180
80.8
6060
5940
7560
19560
TOTAL MOMENT = Empty weight CG or 19560 = 80.8
TOTAL WEIGHT 242
FIGURE 2. EMPTY WEIGHT CG
2. DETERMINING EMPTY WEIGHT CG.
a. The sample airplane for determining empty weight is a single seater, which the kit manufacturer’s design empty weight of 253 pounds and a gross weight limit of 500 pounds. The datum line is located at the nose of the aircraft and the CG range is between 69 to 74 inches from the datum.
FIGURE 2. EMPTY WEIGHT CG
b. To work a CG problem, figure the EMPTY WEIGHT CG first. On a piece of paper draw four blocks. Title each block from left to right as shown in figure 3.
(1) Under the block titled item, vertically list ‘‘left wheel,’’ ‘‘right wheel,’’ and ‘‘nose/tail wheel.’’
(2) Place a calibrated scale under each wheel and record the weight on each gear, in pounds,
in the weight block along side the appropriate wheel. This process is done with an empty fuel tank.
(3) Measure in inches the distance from the datum line, or imaginary point identified by the manufacturer (e.g., nose of the aircraft), to the center line (C/L) of the three wheels. Record the distance of each wheel and place it in the moment arm block beside the appropriate wheel (see figure 2).
(4) Multiply the number of inches (arm) by the weight on each wheel to get the moment (inchpounds) for each wheel. Add the weight on the three gears and the three moments in inch pounds and divide the total weight into the total moment. The sum is the ‘‘EMPTY WEIGHT CENTER OF GRAVITY’’ in inches. In the sample case, the empty weight CG is 80.8.
NOTE: All calculations should be carried out to two decimal places.
16
ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)
A/C
Pilot
Fuel
TOTALS
242
170
30
442
80.8
65
70
74
19560
11050
2100
32710
TOTAL MOMENT = Takeoff CG or 32710 = 74
TOTAL WEIGHT 442
FIGURE 3. TAKE-OFF CG
3. DETERMINING TAKE-OFF WEIGHT CG.
FIGURE 3. TAKE-OFF CG
a. Since the aircraft’s empty weight and empty weight CG are fixed numbers, the only way an aircraft’s CG can be changed is by adding weight in other locations.
b. For example, in figure 3, the aircraft’s empty weight has been written in the appropriate blocks. The pilot weighs 170 pounds and fuel (5 gallons) weighs 30 pounds.
c. Again, all measurements are made from the datum to the center line of the object that has been added. Weight multiplied by inches from the datum equals moment. Add the weights and moments to find the take-off CG for that particular flight.
d. Loaded in this configuration, the aircraft is within the CG flight envelope and is safe to fly.
17
ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)
ITEMS WEIGHT (LBS) ARM (INCHES) MOMENT (IN-LBS)
A/C
S/B
Pilot
Strobe
Fuel
Fuel
TOTALS
242
15
170
1.5
30
1.5
460
80.8
75
65
179
70
55
74.3
19560
1125
11050
268.5
2100
82.5
34186
TOTAL MOMENT = Alteration Takeoff Weight CG or 34186 = 74.3
TOTAL WEIGHT 460 FIGURE 4. ADDITIONAL EQUIPMENT ADDED
TOTAL WEIGHT 460 FIGURE 4. ADDITIONAL EQUIPMENT ADDED
4. ADDING ADDITIONAL EQUIPMENT.
a. During flight testing, a strobe battery and hand held radio are added. The battery/battery box weight is 15 pounds and the location is 75 inches aft of the datum; the strobe assembly weight is 1.5 pounds and is located 179 inches aft of the datum; the radio’s weight is 1.5 pounds and is located 55 inches aft of the datum (see figure 4).
b. In the sample problem, the previous figures for take-off weight and moment are still accurate, hence those numbers have been listed in the appropriate blocks.
(1) Add the battery, strobe, and radio numbers in the appropriate locations and calculate the totals. At 465 pounds, the aircraft is still 35 pounds under its design gross weight limit of 500 pounds but is out of balance because the CG has moved .3 inches further aft (74.3 inches) than the allowable rear CG limit of 74 inches.
(2) Since the aircraft is out of balance with an aft CG, it is no longer 100 percent stable in pitch and would be dangerous to fly. In most cases, it is not the amount of weight added to the aircraft that can cause a major safety problem but its location.
(3) To bring this aircraft back into the safe CG range, the battery would have to be moved 9 inches forward (66 inches from the datum line). Another alternative is to install 8 pounds of ballast in the nose (20 inches from the datum).
(4) If the sample aircraft exceeded the designer’s gross weight limit (e.g., 300 pound pilot) instead of the CG limit, its climb, stall, and performance capability would be poor and the possibility for in-flight structural failure would be high.
NOTE: In the sample weight and balance, positive numbers were chosen by placing the datum line on the nose of the aircraft. Some manufacturers prefer to use a datum located somewhere between the aircraft’s nose and the leading edge of the wing.
(5) This kind of datum will set up a system of positive arms (items located aft of the datum) and negative arms (items located forward of the datum).
(6) When working a weight and balance problem with negative and positive moments, subtract the sum of all negative moments from the sum of all positive moments to reach a ‘‘total moment’’ for the aircraft.
18
SECTION 9. PAPERWORK
SECTION 9. PAPERWORK
‘‘It is harder to write a lie in a logbook than tell one, because your eyes see it and your fingers feel
it.’’ Bob Moorman, Ultralight Instructor (1994)
1. OBJECTIVE. To have the proper documentation and paperwork to conduct the flight test.
a. Weight and Balance: The weight and balance for the aircraft should be carefully done. The gross weight and CG range should be determined prior to every flight.
b. Airworthiness/Registration/Operating Limitations/Placards/Weight and Balance: Must be on board, or the aircraft is not legal to be operated.
c. Checklists: In addition to the assembly/airworthiness checklist previously discussed in section 7, the builder should prepare the following checklists: preflight; take-off/cruise; before starting; descent/before landing; starting the engine; after landing; before takeoff; securing the aircraft; and emergency procedures. A checklist to cover the above procedures may seem a tedious task, but it will only be the size of a 5x8 card -- similar to a checklist for a Cessna 150 or a Piper PA-28-140.
NOTE: The amateur-builder should anticipate several revisions to the checklists.
d. Flight Manual: It is imperative a flight manual describing the anticipated performance of the aircraft be written by the aircraft builder/kit manufacturer. The manual will be revised several times during the flight test phase until it accurately reports the aircraft’s performance.
e. Maintenance Records (logbooks): Operators of amateur-built aircraft are required to only record the yearly condition inspections in accordance with the aircraft’s operating limitations. The FAA recommends, however, that every amateur-built aircraft/ultralight owner record in the aircraft’s logbooks all inspections and maintenance performed. This will create an aircraft’s maintenance history and will be invaluable in spotting trends.
19
SECTION 10. POWERPLANT TESTS
SECTION 10. POWERPLANT TESTS
‘‘Don’t short-change the engine tests or you won’t be around to give your grandkids a ride.’’ Dick Koehler,
A&P Instructor (1994)
1. OBJECTIVE. To ensure that the engine has been properly run-in and is safe to operate in all rpm ranges.
a. An engine pre-oil and cold compression test can be conducted as follows:
(1) Remove the rocker-box covers and one spark plug from each cylinder.
(2) Using an external oil pump, or by rotating the propeller in the direction of rotation, pump a substantial supply of oil up from the sump into the rocker arms.
(3) When the engine is pre-oiled, run a cold compression test of each cylinder.
(4) The results will serve only as an initial bench mark for comparing other compression tests taken after the engine has been run-up to operating temperature.
b. New/newly overhauled engine run-in procedures:
(1) Most amateur-builders start with a new or newly overhauled engine and proceed to ‘‘run it in’’ on the airframe. This practice is followed due to lack of access to a test cell or a special ‘‘club’’ propeller that is specifically designed to aid in engine cooling during run-in. There are pros and cons to using an airframe to run in an engine, but the best advice has always been to follow the engine manufacturer’s instructions. These instructions are found either in the manufacturer’s overhaul manuals, service bulletins, or service letters. Following the manufacturer’s instructions is especially important if the engine has chrome cylinders which require special run-in procedures.
(2) Also, before running-up the engine, be certain that it has the proper grade oil in the sump. Some new and newly overhauled engines are shipped with a special preservative oil to prevent corrosion.
20
Drain this out and reservice the engine with the correct oil before starting.
c. Used engine run-in procedures: Some amateur-builders install a used engine from a flyable aircraft. The same checks and adjustments used on a new or newly overhauled engine should be conducted. New and used engines require special attention to engine cylinder baffling to ensure cylinder cooling is within the engine manufacturer’s cylinder head temperature specifications.
d. Pre run-in checks:
(1) Before beginning the powerplant tests, inspect the engine and propeller carefully. All fuel and oil line connections should be tight. Check the torque on the engine mount attaching bolts. Be certain that there are no tools, hardware, or rags laying between the cylinders or under the magnetos.
(2) Check for the proper amount of oil in the engine and that the dip stick gives an accurate reading of the oil quantity. Be advised that some engines were mounted on an angle in type certificated aircraft. These engines have a special part number oil dip stick, which corrects for the different angle of oil in the crankcase. The same engine, mounted level in a amateur-built aircraft with the original dip stick, will not show the correct oil quantity.
e. Test and Support Equipment:
(1) A cylinder head temperature gauge (CHT) is needed to ensure that all cylinders are receiving the proper flow of cooling air.
(2) On the newer aircraft engines, the cylinders are drilled and tapped to accept a bayonet type of CHT thermocouple probes. For older engines, the thermocouple is designed like a spark plug washer and fits under a spark plug. It can be installed in any cylinder, either under the top or bottom spark plug.
(3) Each type of CHT design can have multiple thermocouples which are connected to a selector switch in the cockpit. The pilot then selects the cylinder he wants to monitor. This also is an excellent troubleshooting tool for identifying fouled plugs and bad ignition leads.
(4) If there is only one CHT thermocouple, attach it to the rearmost cylinder on the right side
of the engine (as viewed from the cockpit) and runup the engine. Run the same test on the opposite rearmost cylinder to be certain the hottest running cylinder was selected. Calibrated oil pressure and oil temperature gauges also are needed to test the accuracy of the engine instruments installed in the aircraft.
(5) The following support equipment is needed: 50 feet or more of tie-down rope, tie-down stakes, two chocks for each wheel, fire extinguisher, assorted hand tools, safety-wire, cotter-pins, ear and eye protection, grease pencils, logbooks, clip board, pen and paper, a watch to time the tests, rags, and manufacturer’s instructions.
f. Safety Precautions: Before the first engine run, ensure the aircraft is tied down, brakes on, and the wheels are chocked. The builder and flight test team should wear ear and eye protection. All flight test participants should be checked out on fire extinguisher use and operation. During engine runs, do not allow anyone to stand beside the engine, or inline or close to the propeller. Making minor adjustments to a running engine, such as idle and mixture settings, is a very dangerous procedure and should be done with great care by experienced individuals.
g. The First Engine Run:
(1) The first start of the engine is always a critical operation. The engine should be pre-oiled in accordance with the manufacturer’s instructions. For aircraft using other than FAA-approved oil pressure and temperature gauges, the FAA recommends attaching an external calibrated oil temperature and pressure gauge to the 4 cycle engine in order to calibrate the engine instruments. After priming the engine and completing the starting engine checklist items, the first concern is to get an oil pressure reading within the first 20 to 30 seconds. If there is no oil pressure reading -- shut down.
(2) There are three common problems that would cause low or fluctuating oil pressure.
(i) Air in the oil pressure gauge line: This is easily fixed by loosening the line connection near the oil pressure gauge and squirting oil into the line until full. Another option is to use a preoiler to provide the pressure and carefully bleed the air out of the line near the oil gauge by loosening the B-nut that connects the oil line to the gauge.
21
(ii) A misadjusted oil pressure relief valve: Cleaning the pressure relief ball, checking for the proper number of washers, correcting spring tension, and re-adjusting the setting could solve the problem.
(iii) An internal problem within the engine (most likely the oil pump): An engine tear down would be required.
(3) With good oil pressure/temperature readings and the engine running smoothly, ensure that the engine oil pressure and temperature gauges in the cockpit match the calibrated oil pressure and temperature gauges, which were attached to the aircraft for the first run. Do not overlook this test. It is critical to determine the accuracy of the cockpit engine gauges not only for the ground engine runin period, but for in-flight engine cooling tests.
(4) Work through the engine manufacturer’s run-in schedule. The majority of the engine manufacturers recommend a series of engine runs from low rpm to maximum rpm. Each run usually incorporates a 200 rpm increase and lasts no longer than 10 minutes. The secret to a successful engine run is not to let the engine temperatures exceed manufacture’s limits during engine runs.
NOTE: Engines with chrome cylinders or chrome rings require different high power run-in programs. Follow the manufacturer’s run-in instructions to ensure the engine will perform satisfactorily over its lifetime.
h. Engine Cool Down: After a ground-run, the cooling off period takes approximately an hour. This is because a newly overhauled engine needs time for the internal parts (e.g., rings, cylinders, valves, bearings, and gear faces) to expand and contract several times to obtain a smooth surface that retains its ‘‘memory.’’ This is a lengthy process even when done right, but it is important not to skip any of the recommended runs to save time. To do so is to risk increasing oil consumption and reducing overall engine performance, reliability, and engine life span -- which could be costly in the long-term.
i. Record the engine run-in data: During the engine run, monitor the cylinder head temperatures, oil temperature, and oil pressure. Record the readings and adjustments for future reference. If the cylinder head temperatures are rising close to the red line, reduce power and stop the test. Some causes of high cylinder head temperatures include using spark plugs with the improper heat range; cylinder head temperature gauges installed on the wrong cylinder; missing or badly designed cylinder head cooling baffles; partially plugged fuel nozzles (applicable to fuel injected engines); fuel lines of improper internal diameter (creates lean mixtures); engine improperly timed either mechanically and/or electrically; and the carburetor fuel mixture set excessively lean.
j. After shut-down:
(1) After each engine run, check for fuel and oil leaks, loose connections, and hot spots on cylinders (burnt paint). The FAA recommends draining the oil and removing the oil screen/filter within the first 2 hours of running the engine. Check the screen/filter for ferrous metal with a magnet. Wash and inspect the screen/filter for non-ferrous metal like brass, bronze, or aluminum.
(2) A very small quantity of metal in the screen is not uncommon in a new or newly overhauled engine. It is part of the painful process of ‘‘running-in.’’ If subsequent oil screen checks (2 hours apart) show the engine is ‘‘making metal,’’ this indicates a problem inside the engine and a tear down inspection is required.
(3) It also is recommended all fuel sumps, filters, and gasolators be checked for debris after each engine run. Special attention should be given to the fuel system by the builder who constructed fuel tanks out of composite or fiberglass materials. Composite and fiberglass strands can be very fine, making visual detection difficult. Frequent cleaning of the fuel filters and screens early in the flight testing phase will avoid a gradual build up of loose composite fibers, which would reduce or stop the flow of fuel to the engine.
22
SECTION 11. ADDITIONAL ENGINE TESTS
SECTION 11. ADDITIONAL ENGINE TESTS
‘‘Always go with the best fix not the cheapest fix.’’ Bill Deeth, Master Mechanic (1994)
1. OBJECTIVE. To determine if the engine supply of fuel is adequate at all angles of attack.
a. Mixture and Idle Speed Check: After completing the initial engine ‘‘run-in’’ tests, check the idle speed and mixture settings. To determine if the mixture setting is correct, perform the following:
(1) Warm up the engine until all readings are normal
(2) Adjust the engine rpm to the recommended idle rpm
(3) Slowly pull the mixture control back to idle cut-off
(4) Just before the engine quits, the engine rpm should rise about 50 rpm if the mixture is properly adjusted. If the rpm drops off without any increase in rpm, the idle mixture is set too lean. If the rpm increases more than 50 rpm, the idle mixture is set too rich.
NOTE: Some amateur-builders, after properly setting the idle mixture/rpm to the manufacturer’s specification, increase the engine idle rpm by 100 rpm for the first 10 + hours of flight testing. This is to ensure that the engine will not quit when the throttle is pulled back too rapidly, or when power is reduced on the final approach to landing.
b. Magneto Check:
(1) The magneto checks should be smooth and the difference between both magnetos rpm drops should average about 50 rpm. The builder also should perform a ‘‘HOT MAG’’ check, to ensure against the engine, on its own, deciding when and where to start. To perform a hot mag check, run up the aircraft until the engine is warm. At idle rpm turn the magneto switch off; the engine should stop running. If the engine continues to run, one or both of the magnetos is hot (not grounded).
(2) The usual causes for a hot magneto are a broken ‘‘P’’ lead coming out of the magneto or a bad magneto switch. THIS IS AN IMMEDIATE
23
THREAT TO THE PERSONAL SAFETY OF ANY- ONE NEAR THE AIRPLANE AND MUST BE REPAIRED AT ONCE.
c. Cold Cylinder Check:
(1) If the engine is running rough and the builder determines it may be an ignition problem, perform the following check:
(i) Run the engine on the bad magneto for about 30 seconds at 1200 rpm. Without switching the mag switch back to ‘‘both,’’ shut off the engine.
(ii) One of the test crew should quickly use a grease pencil to mark an area of the exhaust stacks approximately an inch from the flange that attaches the stacks to the cylinders.
(iii) Check the marks on the stacks. If one or more of the exhaust stacks with a grease mark has NOT been burned to a grayish-white color and the mark on the stack still retains most of the original color of the grease pencil, the ‘‘cold cylinder’’ has been identified.
(2) Probable causes of the cold cylinder problem are defective spark plugs, ignition leads, or a cracked distributor in one of the magnetos. To detect if the spark plugs are bad, switch both plugs to another cylinder. If the grease pencil proves the problem moved to the new cylinder, the spark plugs are bad. If the problem remains with the original cylinder, the ignition lead or magneto is bad.
d. Carburetor Heat:
(1) It is strongly recommended that all amateur-builders install a carburetor heat system that complies with the engine manufacturer’s recommendation. If no recommendation is available, the FAA suggests a carburetor heat system for a sealevel engine and a conventional venturi should be designed so that it will provide a 90 degrees F increase in the venturi at 75 percent power. For altitude engines using a conventional venturi carburetor, 120 degrees F increase in venturi temperature at 75 percent power will prevent or eliminate icing. Remember: Too little carburetor heat will have no effect on carburetor icing, and too much carburetor heat will cause a overly rich mixture which will reduce power and may shut down the engine.
(2) During the engine tests, make numerous checks of the carburetor heat system. To avoid overly rich mixtures from oversized carburetor heat ducts, ensure that the carburetor heat duct is the same size as the inlet of the carburetor.
(3) Be certain there is a positive reduction in rpm each time ‘‘carb heat’’ is applied. If there is no reduction, or the rpm drop is less than expected, check the carb heat control in the cockpit and on the carb heat air box for full travel. Also check for air leaks in the ‘‘SCAT TUBE’’ that connects the heat muff to the carburetor air box.
e. Fuel Flow and Unusable Fuel Check: This is a field test to ensure the aircraft engine will get enough fuel to run properly, even if the aircraft is in a steep climb or stall attitude.
(1) First, place the aircraft’s nose at an angle 5 degrees above the highest anticipated climb angle. The easiest and safest way to do this with a conventional gear aircraft is to dig a hole and place the aircraft’s tail in it. For a nose gear aircraft, build a ramp to raise the nose gear to the proper angle.
(2) Make sure the aircraft is tied-down and chocked. With minimum fuel in the tanks, disconnect the fuel line to carburetor. The fuel flow with a gravity flow system should be 150 percent of the fuel consumption of the engine at full throttle. With a fuel system that is pressurized, the fuel flow should be at least 125 percent. When the fuel stops flowing, the remaining fuel is the ‘‘unusable fuel’’ quantity.
(3) Since the fuel consumption of most modern engines is approximately .55 pounds per brake horsepower per hour for a 100 horsepower engine, the test fuel flow should be 82.5 pounds (13.7 gallons) per hour for gravity feed, or 68.75 pounds (11.5 gallons) per hour for a pressurized system. The pounds per hour divided by 60 equals 1.4 pounds and 1.15 pounds per minute fuel rate respectively.
NOTE: Formula for fuel flow rate gravity feed is .55 x engine horsepower x 1.50 = pounds of fuel per hour divided by 60 to get pounds per minute, divided by 6 to get gallons per minute. For a pressurized system, substitute 1.25 for 1.50 to determine fuel flow rate.
f. Changing Fuel Flow or Pressure: If the aircraft’s fuel flow rate is less than planned, there
24
is a volume or pressure problem. An increase in the fuel flow volume may necessitate installation of larger fuel line fittings on the fuel tanks, fuel selector, and carburetor in addition to larger internal diameter fuel lines. To increase fuel pressure, install an electrically driven or engine driven mechanical fuel pump prior to the first flight.
g. Compression Check: When the engine runin procedures have been completed, perform an additional differential compression check on the engine and record the findings. If a cylinder has less than 60/80 reading on the differential test gauges on a hot engine, that cylinder is suspect. Have someone hold the propeller at the weak cylinder’s top dead
center and with compressed air still being applied, LISTEN. If air is heard coming out of the exhaust pipe, the exhaust valve is not seating properly. If air is heard coming out of the air cleaner/carb heat air box, the intake valve is bad. When the oil dip stick is removed and air rushes out, the piston rings are the problem.
h. Last Check: Drain the oil and replace the oil filter, if applicable. Check the oil and screens for metal, visually inspect the engine, and do a runup in preparation for the taxi tests. Do not fly the aircraft if anything is wrong, no matter how small or how insignificant. The sky, like the sea, is an unforgiving and uncompromising environment.
25
SECTION 12. PROPELLER INSPECTION
SECTION 12. PROPELLER INSPECTION
‘‘A tough decision is what a man makes when he cannot form a committee to share the blame’’ George
Lutz, Col. U.S. Air Force, Retired (1994)
1. OBJECTIVE. To help the amateur-builder/ ultralight aircraft owner develop an inspection program to maintain his/her propeller.
a. There are three kinds of propeller designs: metal, wood, and composite.
(1) Because of weight considerations, metal propellers are used more on amateur-built aircraft than ultralight aircraft. This makes wood and composite propellers the overwhelming choice for ultralight aircraft.
(2) Wood propellers are light, reliable, and inexpensive but require frequent inspections.
(3) Composite carbon-graphite material props are more expensive than wood, but are stronger and require less maintenance.
b. All types of propellers have one thing in common: they are constantly under high levels of vibration, torque, thrust, bending loads, and rotational stress. Even small nicks in the leading edge
of the blade can very quickly lead to a crack, followed by blade separation. Propeller tip failure and a subsequent violent, out of balance situation can cause the propeller, engine, and its mounts to be pulled from the airframe in less than 5 seconds.
c. It is essential that the make and model propeller is carefully chosen. Always follow the manufacturer’s recommendations.
d. Exercise caution if experimenting with different makes and models propellers. A propeller with the wrong size and pitch will give a poor rate of climb, cruise, or could cause the engine to ‘‘overrev.’’
2. RECOMMENDATIONS FOR ALL PROPELLERS.
a. Never use a propeller for a tow bar when moving the aircraft.
b. Never stand in front of or in-line of a rotating propeller.
26
c. Never ‘‘PROP’’ an engine on uneven or wet/snow covered ground.
d. Always inspect the propeller before and after a flight.
e. When working on a propeller, make sure the ignition is off first.
f. Always maintain the propeller to manufacturer’s instructions.
g. To avoid nicks and cuts, do not perform run-ups near gravel/loose stones.
h. Apply a coat of automotive wax once a month to protect the finish and keep out moisture.
i. Assume a propeller is unairworthy if it has suffered any kind of impact or ground strike.
j. After any repair or repainting, or if vibration or roughness is noted, re-balance the propeller.
k. Propeller blades should be balanced within 1 gram of each other to avoid over stressing the gear reduction system and propeller shaft.
l. Check the bolt torque on all newly installed propellers every hour of operation for the first 10 hours and once every 5 hours thereafter.
m. After torquing the propeller, track the blades.
FIGURE 5 - Propeller Tracking
3. PROPELLER TRACKING CHECK.
a. Ensuring good powerplant operation first starts with a properly installed propeller. Each propeller should be checked for proper tracking (blades rotating in the same plane of rotation). The following procedure is simple and takes less than 30 minutes:
(1) Chock the aircraft so it cannot be moved. Remove one sparkplug from each cyl-
inder. This will make the propeller easier and safer to turn.
(2) Rotate the blade so it is pointing straight down.
(3) Place a solid object (e.g., a heavy wooden block that is at least a couple inches higher off the ground than the distance between the propeller tip and the ground) next to the propeller tip so it just touches.
27
(4) Rotate the propeller slowly to see if the next blade ‘‘tracks’’ through the same point (touches the block, see figure 2). Each blade should be within 1⁄16’’ from one another.
b. If the propeller is out of track, it may be due to one or more propeller blades that are bent, a bent propeller flange, or propeller mounting bolts that are over or under torqued. An out-of-track propeller will cause vibration and stress to the engine and airframe and may cause premature propeller failure.
4. METAL PROPELLER INSPECTION Perhaps the two biggest problems affecting the airworthiness of metal propellers are corrosion and nicks on the leading edge.
a. Identifying Corrosion.
(1) Surface corrosion can occur on the surface of metal blades due to a chemical or electrochemical action. The oxidation product usually appears on the surface of the metal as a white powder.
(2) Pitting corrosion causes small cavities or pits extending into the metal surface. This is an advanced form of corrosion, appearing as small dark holes that usually form under decals or blade overlays.
(3) Inter-granular corrosion, rare and difficult to detect in propellers, is the most dangerous form of corrosion. It attacks the boundary layers of the metal, creating patches of lifted metal and white/ gray exfoliation on the surface of the propeller. It is sometimes found in propellers that had a ground strike and have been straightened.
(4) If any of these signs of corrosion are found, do NOT fly the aircraft. Refer to the manufacturer’s maintenance manual for corrosion limits and repairs or AC 43.4, ‘‘Corrosion Control for Aircraft,’’ and AC 20-37D, ‘‘Aircraft, Metal Propeller Maintenance,’’ for additional maintenance information and corrective actions.
b. Nicks and Metal Blades.
(1) Nicks in the leading and trailing edge of a metal blade are usually V-shaped. They are caused by high speed impact between the propeller and a stone or piece of gravel. Properly trained individuals can ‘‘dress out’’ the crack if the nick
is not too wide and/or deep. Before each nick is dressed out, each nick and surrounding area should be inspected with a 10-power magnifying glass for cracks. If an area looks suspicious, inspect the area again using the propeller manufacturer’s approved dye penetrant or fluorescent penetrant method.
(2) If the nick is left unattended, the high propeller operational stresses will be concentrated at the bottom of the nick’s V and, in time, will generate a crack. The crack can migrate across the blade until the blade fails, producing a massive imbalance between the propeller and the engine, ultimately causing structural failure. Cracks in metal blades CANNOT be repaired. A cracked propeller must be marked unserviceable and discarded.
c. Warning. Metal propellers are matched/ tuned to the engine and airframe resonant frequency by being manufactured with a particular diameter to minimize vibration. DO NOT SHORTEN METAL BLADES for any reason unless the manufacturer specifically permits this major alteration.
5. PROPELLER INSPECTION.
a. Wood propellers should be inspected before and immediately after a flight. Inspect to ensure the following:
(1) The drain holes are open on metal edged blade tips
(2) The metal/composite leading edge is secured and serviceable
(3) The blades, hub, and leading edge have no scars or bruises
(4) The mounting bolt torque and safety wire or cotter pins are secure
(5) There are no cracks on the propeller spinner (if applicable), and the safety wire is secure
(6) There are no small cracks in the protective coating on the propeller, which are caused by UV radiation
(7) The charring around the mating surface of the prop and the engine flange -- both indications of a loose propeller
b. A word about torque: A new, wooden propeller should have the mounting bolts checked
28
for proper torque within the first hour of flight and every hour for 10 operational hours thereafter.
(1) After 10 hours, check the bolt torque every 5 hours thereafter. The mounting bolt torque also should be checked prior to flight if the aircraft has been in storage for a long period of time (3 to 6 months).
(2) If the bolts need to be torqued, it is suggested all the bolts be loosened for an hour to allow the wood to relax. ‘‘Finger tighten’’ the bolts until snug and tighten the attaching bolts in small increments, moving diagonally across the bolt circle. It is good practice to check the propeller track (see chapter 1, section 7) as the bolts are torqued down. The torqued bolts should be safety wired in pairs.
(3) If nylon/fiber insert type nuts are used, they should be changed every time the propeller bolts are re-torqued. They should never be used with a bolt with a cotter key hole in the threaded area because the sharp edges around the hole will cut the nylon/fiber insert and reduce the fastener’s effectiveness. All self-locking nuts should have at least two bolt threads visible pass the nylon/fiber insert after torquing.
(4) If any of the following damage is found, a wood propeller should be removed from the aircraft and sent back to the manufacturer for repair. If the propeller cannot be saved, it should be marked unserviceable.
(i) Any cracks in the blades or hub
(ii) Deep cuts across the wood grain
(iii) Blade track that exceeds 1⁄16’’ limits after attempts to repair
(iv) Any warpage or obvious defect
(v) Extreme wear (leading edge
erosion, bolt hole elongation)
(vi) Any separation between
lamination
NOTE: When parking the aircraft, always leave the wood propeller in the horizontal position. This position will allow the wood to absorb small amounts of moisture evenly across it’s entire span rather than concentrating the moisture (weight) in the low blade and creating a vibration problem.
6. COMPOSITE PROPELLERS
6. COMPOSITE PROPELLERS
INSPECTION.
a. There are generally two types of composite propellers: thermo-plastic injection molded propeller and the carbon/graphite fiber composite propeller.
(1) The thermo-plastic injection molded propeller is a low cost, thin bladed propeller used on engines of 80 horsepower or less. Propeller inspection is straight forward, by examining the blades and hub for cracks and nicks. If a crack is found, do not fly until the propeller is replaced. Small nicks of 3⁄16 of an inch or less can be dressed out and filled using a two-part epoxy.
(2) Carbon/graphite composite propellers are primarily used on engines of 40 horsepower and more. One should inspect for small hair line cracks in the gel coat. These spider cracks are usually caused by vibration generated by a mismatch of the engine and propeller combination. If a crack in the base material of the propeller other than the gel coat is found, do not fly until the manufacturer inspects the propeller.
(i) Nicks of 1⁄2 inch or less in the leading or trailing edges of carbon/graphite propellers can be dressed out and filled using a two-part epoxy. But if the nick has severed the fiberglass roving (looks like a fiberglass wire bundle) that runs hub to tip on the leading and trailing edge, do not fly. The propeller has been severely damaged and must be sent back to the factory for inspection and repair.
(ii) Before making even small repairs on a composite propeller, check with the manufacturer first. Larger nicks must go back to the factory for inspection and repair.
29
CHAPTER 2. TAXI TESTS
CHAPTER 2. TAXI TESTS
SECTION 1. LOW SPEED TAXI TESTS
‘‘Yelling ’Clear the Prop!’ before you start an aircraft is the first of a series of well planned, choreographed steps to make you a professional.’’ Jack Crawford, Pilot, Mechanic, Airport Operator
(1994)
1. OBJECTIVES. The objectives of the taxi tests are fourfold:
SECTION 1. LOW SPEED TAXI TESTS
a. To ensure that the aircraft ‘‘tracks’’ straight and there is adequate directional control at 20 percent below the anticipated take-off speed.
b. To determine if the aircraft’s engine cooling and the brake system are adequate.
c. To predict the flight trim of the aircraft and its handling characteristics during take off and landings.
d. To allow the pilot to become proficient with the handling and braking characteristics of the aircraft.
NOTE: All taxi tests, low and high speed, should be made as if it were the first flight. The pilot should be wearing the proper clothing, seat belt/shoulder harness and helmet and be mentally and physically prepared for the possibility of flight.
2. TAXI TESTS.
a. Prior to beginning taxi tests in a conventional (tail dragger) aircraft, the tail should be raised until the aircraft is in the approximate take-off position. The pilot should spend an hour or more in the cockpit to become accustomed to the aircraft’s takeoff position. This small but important aspect of training will help the pilot avoid overreacting to an unexpected deck angle on the first flight.
NOTE: All taxi tests should always be monitored by a minimum of one other member of the flight test team, who will watch for evidence of fire/smoke or other problems not visible to the pilot.
b. The taxi tests should begin with a taxi speed no faster than a man can walk. The pilot should spend this time getting acquainted with the aircraft’s low speed handling characteristics by practicing 90, 180, and 360 degree turns and braking action. The pilot should also remember that monitoring the oil pressure, oil temperature, cylinder head temperature, and maintaining them within limits is a critical function that must not be overlooked.
30
NOTE: The builder should be aware that some aircraft brake manufacturers have specific brake lining conditioning procedures (break-in) for metallic and non-asbestos organic linings. Proper brake lining conditioning should be completed before starting the low and high speed taxi tests. If not properly conditioned, the brake lining will wear quickly and give poor braking action at higher speeds.
c. The pilot should check the flight instruments for operation each time the aircraft is
taxied out. The compass should match the magnetic heading of the runway or taxi way the aircraft is on. When making a turn (e.g., right hand turn), the turn coordinator/turn and bank should indicate a right hand turn but the ball should skid to the left. The vertical speed indicator should read zero and the artificial horizon should indicate level.
d. After each taxi run, inspect the aircraft for oil and brake fluid leaks. No leak should be considered a minor problem. Every leak must be repaired and the system serviced prior to the next taxi test.
SECTION 2. HIGH SPEED TAXI TESTS
SECTION 2. HIGH SPEED TAXI TESTS
‘‘First get use to the fact that you are now 30 feet wide and you steer with your feet.’’ Wayne Nutsch
1. OBJECTIVE. To determine the aircraft’s high speed handling and braking parameters.
a. Propeller rotation will determine which rudder pedal is pressed to compensate for the asymmetrical thrust of the propeller blades. For example, when viewed from the cockpit, a Volkswagen automotive engine mounted in a tractor configuration will rotate the propeller counter-clockwise. In this case, the pilot must use the left rudder pedal for high speed taxi and take-off.
b. As with every part of the flight testing program, the high speed taxi tests should follow the FLIGHT TEST PLAN. Start slowly and do not progress to the next step until everyone is thoroughly satisfied with the aircraft and his/her own performance.
c. Each taxi run should be 5 mph faster than the last run until the aircraft is within 80 percent of the predicted stall speed. Prior to reaching the predicted stall speed, the pilot should test aileron effectiveness by attempting to rock the wings slightly. As taxi speeds increase, the rudder becomes more responsive and directional control will improve.
(1) In a nose gear aircraft, the pilot should be able to raise the nose of the aircraft to a take off attitude at 80 percent of the stall speed. If the nose cannot be raised at this speed, the weight and balance and CG range should be rechecked. Most likely there is a forward CG problem or the main gear is too far aft.
(2) In a tail wheel aircraft at 80 percent of stall speed, the pilot should be able to lift the tail and assume a take-off position. Again, if the tail cannot be raised, recheck the weight and balance and CG range. Most likely there is a rearward CG problem or the main gear is too far forward.
CAUTION: Heavy braking action at high speeds in tail wheel aircraft may cause directional problems (ground loops) or nose overs.
c. If runway conditions permit, duplicate each taxi test with the flaps in the take-off and landing configuration. Record the flap effects on directional control and insert the information in the draft copy of the aircraft’s flight manual.
d. Determine the approximate point on the runway where lift-off will occur and mark it with a green flag if no other existing reference is available.
e. Determine how much runway the pilot will need if it becomes necessary to abort the take-off. This is usually accomplished by accelerating to 80 percent of lift off speed, bringing the engine back to idle, and applying heavy braking action to bring the aircraft to a full stop. After each take-off/abort test, the brakes must be allowed to COOL DOWN. The lining must be examined carefully and replaced if necessary.
f. After determining the distance required to come to a full stop after aborting, add 30 percent to the distance. Measure that distance from the OPPOSITE end of the active runway which will be
31
used. If no existing reference is available, mark it with a red flag. The taxi tests are completed when the test pilot is satisfied with both the aircraft’s and his/her individual performance. Prior to the first flight, the aircraft should be thoroughly inspected with special attention given to the landing gear, brake system, engine, and propeller.
g. During this inspection all discrepancies must be fixed. Examine the screens/filters for metal, flush the fuel system, and clean all the screens/filters. Perform a leak check on the engine and the fuel system by running-up the engine.
h. Notes.
(1) The first high speed taxi tests should be made in a no wind or a light head wind condition. The pilot should ensure that the tests will not interfere with the normal airport operations or create a safety hazard for other aircraft.
(2) If the aircraft’s engine is not a U.S. type certificated engine, the pilot should determine which way the propeller rotates.
(3) Pilots of tail wheel aircraft must always be aware that ground loops are possible at any speed. This is true especially if the main landing gear is located too far forward of the aircraft’s CG.
32
THIS PAGE INTENTIONALLY LEFT BLANK
THIS PAGE INTENTIONALLY LEFT BLANK
33
CHAPTER 3. THE FIRST FLIGHT
‘‘It is critically important that a test pilot never succumb to the temptation to do too much too soon, for
that path leads but to the grave.’’ Richard Hallion (1987)
SECTION 1. GENERAL
1. OBJECTIVE. To take every precaution to ensure that the first test flight is an ‘‘uneventful’’ one.
SECTION 1. GENERAL
2. GENERAL.
a. The first flight is an important event for an amateur-builder. As important as it is, it should not be turned into a social occasion. This puts enormous peer pressure on the pilot to fly an aircraft that may not be airworthy or to conduct the flight in inclement weather.
b. A ‘‘professional’’ will avoid this trap by following the FLIGHT TEST PLAN and inviting only those members of the crew needed to perform specialized tasks when testing the aircraft.
c. A safe and uneventful first flight begins with verifying all emergency equipment and personnel are standing by, radio communications are functional, members of the crew are briefed, weather is ideal, and the aircraft is airworthy. The pilot must be rested and physically and mentally ready for the first flight and every flight thereafter. The pilot also should review any new data developed for the aircraft’s flight manual.
d. The first flight should be flown a thousand times: the first 500 on paper, the next 499 flights in the test pilot’s mind -- and once in actuality. The first flight test should be so well-rehearsed by the test pilot and ground crew that the first flight is a non-event.
34
31. RECOMMENDATIONS.
a. The best time to test fly an aircraft is usually in the early morning when the winds are calm, and the pilot is well rested.
b. In addition to a pilot’s knee board, a small portable tape recorder or video camera properly mounted to the aircraft is an excellent way to record data.
c. Good communication with the ground is essential for data exchange and safety.
4. FIRST FLIGHT INSPECTION.
a. Prior to the first flight, the aircraft should be given a good pre-flight inspection by the pilot and at least one other experienced individual. A thorough aircraft pre-flight inspection should ensure that:
(1) The fuel on board is four times the amount of usable, clean, and proper octane fuel than is needed for the first flight. If a 2 cycle engine is used, check that the oil to fuel mix ratio is correct.
(2) A current weight and balance check is completed. The aircraft’s CG should be in the forward half of the safe CG range. This will reduce the possibility of instability during approach to a stall and enhance recovery from one.
(3) Check oil, brake fluid, and hydraulic system for the correct fluid and quantity.
(4) Canopy or cabin door latches lock securely and will not vibrate loose in flight.
(5) Fuel valve is in the proper position and vent lines are open.
(6) Trim tabs set in the take-off position.
(7) Altimeter set to the field elevation and cross-checked with the local altimeter setting.
(8) The complete control system has been given a functional check.
(9) Check of all ground and air communications frequencies for proper operation.
(10) Engine cowling and airframe inspection plates/fairings secured.
(11) The airspeed indicator marked with sticky tape at the ‘‘predicted’’ BEST CLIMB speed, BEST GLIDE speed and MANEUVERING speed. If these speeds are not available from prototype flight test data, the following are conservative guidelines to initially determine the referenced speeds:
(i) BEST ANGLE OF CLIMB (Vx) = 1.5 times the aircraft’s predicted lift-off speed.
(ii) BEST GLIDE SPEED = 1.5 times the aircraft’s predicted lift-off speed.
(iii) MANEUVERING SPEED (Va) = 2 times the aircraft’s predicted stall speed.
(iv) For applicable aircraft, it is advisable to put the maximum landing gear operating speed (Vlo) and maximum flap extension speed (Vfe) on a piece of masking tape and attach it to the instrument panel for reference.
SECTION 2. THE ROLE OF THE CHASE PLANE
SECTION 2. THE ROLE OF THE CHASE PLANE
1. OBJECTIVE. To determine whether a chase plane should be used during the FLIGHT TEST PHASE.
2. GENERAL. To use or not to use a chase plane should be a ‘‘test pilot’s’’ decision. If a chase plane is used, it must serve a specific set of functions identified in the FLIGHT TEST PLAN. Its overall purpose is to contribute to gathering flight test data and flight safety. The chase plane should not serve as a distraction to the test pilot or only as a platform for a home camcorder/camera.
a. The primary functions of the chase plane are as follows:
(1) To watch the parts/systems of the test aircraft not visible to the test pilot and report any problems
(2) To assist the test pilot in following the FLIGHT TEST PLAN
(3) Watch for and inform the test pilot of other aircraft
(4) Assist in an emergency situation
35
b. If a chase plane is used, the following suggestions are offered:
(1) A single chase plane should be used on the first two flights and the first time the amateurbuilt aircraft’s landing gear is retracted. The chase plane pilot should be experienced in formation flying and thoroughly briefed prior to each flight.
(2) There should be at least two pilots on board the chase plane. One pilot’s sole duty is to fly the aircraft and maintain a safe distance from the amateur-built aircraft. The other pilot serves as an observer whose duties include checking for other traffic, the condition of the test aircraft, and communicating with the pilot on the frequency assigned by air traffic control (ATC) (e.g., 122.75 megahertz [MHz]).
(3) A good chase plane position is about 100/200 feet off the right side and slightly behind and below the test aircraft. Avoid flying directly behind the test aircraft. It is not uncommon that on
first flights, fuel and oil leaks develop and small hardware and fasteners could vibrate off the aircraft.
NOTE: Pilots of Both Aircraft Must Keep Each Other Informed of Their Intended Action or Maneuver Prior to Execution.
c. In an emergency situation:
(1) If the test aircraft’s radio fails, the chase plane should serve as an airborne communication relay with the tower/ATC facility for the test aircraft.
(2) For other emergency situations, the chase plane should provide the test pilot with information or assistance as required. If necessary, the chase plane can guide the test pilot to a safe landing at the airport or an emergency field. If the test aircraft goes down off the airport, the chase plane can serve as an overhead spotter that can direct emergency personnel to the test aircraft location.
SECTION 3. EMERGENCY PROCEDURES
SECTION 3. EMERGENCY PROCEDURES
‘‘At the worst possible time, the worst possible thing will happen.’’ Murphy’s Law
1. OBJECTIVE. To develop a complete set of in-flight emergency procedures for the aircraft that are designed to make unmanageable situations manageable.
2. GENERAL. The FLIGHT TEST PLAN should have a special section on emergency procedures. The responses to each emergency should have been developed based on the aircraft’s predicted flight characteristics, airport location, surrounding terrain, and nearby emergency fields.
a. The following is a partial list of possible emergencies that may arise during the flight test phase and includes suggested responses:
(1) PROBLEM: Engine failure on takeoff.
RESPONSE: Fly the aircraft! Establish best glide speed. If time permits, try to restart engine. If altitude is below 800 feet and the engine will not start, land straight ahead or 20 degrees on either side of the runway centerline. This is suggested because in most cases the aircraft will run
out of altitude or airspeed as the pilot attempts a 180 degree turn back to the airport. Declare an emergency and shut off the master switch, fuel, and magnetos to reduce the possibility of fire on landing. Above 800 feet, the chances of making a 180 degree turn to land downwind on the runway or another emergency field nearby are directly proportional to the wind velocity and the numbers of practice emergency landings the pilots has made in similar make and model aircraft.
(2) PROBLEM: Engine vibration increases with rpm.
RESPONSE: Fly the aircraft! Reduce power or increase power to minimize the effect of vibration, but maintain safe airspeed and altitude. Run through the emergency checklist and land as soon as possible.
(3) PROBLEM: Smoke in the cockpit.
RESPONSE 1: Fly the aircraft! If the smoke smells like burnt plastic wire installation, shut off the master switch. Put on smoke goggles,
36
open the fresh air vents to clear the cockpit, and land as soon as possible.
RESPONSE 2: Fly the aircraft! If the smoke is bluish/grey and has an acrid odor like burning oil, shut off the fresh air/hot air vents and put on the smoke goggles. Monitor oil pressure and temperature. Be prepared to shut the engine down and land as soon as possible.
(4) PROBLEM: Engine fire.
RESPONSE: Fly the aircraft! Shut off the fuel selector, mixture master switch, and magnetos. Land as soon as possible.
(5) PROBLEM: Out of rig condition.
RESPONSE: Fly the aircraft! Try to use the appropriate trim to offset adverse control pressures. Keep the airspeed high enough to maintain altitude. Make small control inputs, reduce power slowly to avoid controllability problems, and land as soon as practical.
(6) PROBLEM: Cabin door opening in flight.
RESPONSE: Fly the aircraft! A partially open door usually affects the airflow over the tail causing reduced control response and vibration. Reduce speed, maintain level flight, and yaw/slip the aircraft left or right to reduce vibration. Open the side vent window to reduce air pressure resistance in the cabin and attempt to shut the door. Sometimes putting the aircraft in a skid will assist in closing a partially open door.
b. Other possible emergencies to plan for include:
(1) Canopy opening unexpectedly
(2) Loss of communications
(3) Throttle stuck in one position
(4) Oil on the windshield
(5) Propeller throws a blade
(6) Fire in the cockpit
SECTION 4. FIRST FLIGHT
SECTION 4. FIRST FLIGHT
‘‘Always leave yourself a way out.’’ Chuck Yeager
1. OBJECTIVES. The two objectives of the first flight are to determine engine reliability and flight control characteristics.
a. After completing the pre-flight inspection, the test pilot should ensure that the seat/shoulder harness is properly fitted and allows easy access to all the cockpit controls (verified by a crew member). Following the FLIGHT TEST PLAN and using the starting checklist, warm up the engine until the engine instruments indicate normal operating temperatures and pressures.
b. A complete check of each aircraft system should be performed (e.g., carb heat, magnetos, static rpm, and brakes).
c. If the airport does not have a tower/unicom available, the pilot should transmit over 122.9 MHz the following message: ‘‘This is experimental aircraft Nlll on the first test flight, departing runway lll at lll airport, and will remain in the local area for the next hour.’’ Transmit the air-
craft N number, location, and intentions every ten minutes.
Continue reading ↓ 120 of 275 passages shown