AC 20-167B Airworthiness Approval of Enhanced Vision System, Enhanced Flight Vision System, and Combined Vision System Equipment
This advisory circular (AC) provides guidance for gaining airworthiness approval for enhanced vision systems in aircraft. Specifically, it provides one acceptable means for complying with title 14, Code of Federal Regulations (14 CFR) part 23, 25, 27, or 29 airworthiness regulations when installing an enhanced vision system (EVS), an enhanced flight vision system (EFVS) or combined vision system (CVS) in an aircraft. This guidance was developed primarily for part 25 aircraft. You may also use this guidance for part 23, 27, and 29 aircraft. As vision system technology advances, applicants are encouraged to propose alternative methods to their AIR certification branch to integrate new and novel safety enhancing vision system functions into their aircraft.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Airworthiness Approval of Enhanced Date: AC No: 20-167B Vision System, Enhanced Flight Vision Initiated by: System, and Combined Vision System AIR-626B Equipment
This advisory circular (AC) provides guidance for gaining airworthiness approval for enhanced vision systems in aircraft. Specifically, it provides one acceptable means for complying with title 14, Code of Federal Regulations (14 CFR) part 23, 25, 27, or 29 airworthiness regulations when installing an enhanced vision system (EVS), an enhanced flight vision system (EFVS) or combined vision system (CVS) in an aircraft. This guidance was developed primarily for part 25 aircraft. You may also use this guidance for part 23, 27, and 29 aircraft. As vision system technology advances, applicants are encouraged to propose alternative methods to their AIR certification branch to integrate new and novel safety enhancing vision system functions into their aircraft.
If you have suggestions for improving this AC, you may use the Advisory Circular Feedback Form at the end of this AC.
DANIEL J.
Digitally signed by DANIEL J. ELGAS ELGAS
Date: 2025.09.08 11:33:13 -04'00' 'DQLHO-(OJDV $YLDWLRQ6DIHW\ 'LUHFWRU3ROLF\DQG6WDQGDUGV'LYLVLRQ$LUFUDIW&HUWLILFDWLRQ6HUYLFH
09/08/2025
TABLE OF CONTENTS
Paragraph Page
CHAPTER 1. INTRODUCTION … 1-1
1.1 Purpose … 1-1 1.2 Applicability … 1-1 1.3 Cancellation … 1-2 1.4 Related Material … 1-2 1.5 Definition of Key Terms … 1-2 1.6 Background … 1-2
CHAPTER 2. VISION SYSTEMS OVERVIEW … 2-1
2.1 Enhanced Vision Systems (EVS) … 2-1 2.2 Enhanced Flight Vision Systems (EFVS) … 2-3 2.3 Combined Vision Systems (CVS) … 2-6
CHAPTER 3. AIRWORTHINESS PACKAGE CONTENTS … 3-1
3.1 Airworthiness Package … 3-1 3.2 Intended Function … 3-1 3.3 Certification of a pre- 14 CFR 91.176 EFVS as an EFVS Landing System … 3-2
CHAPTER 4. SYSTEM CRITERIA … 4-1
4.1 EVS (or CVS when EVS and SVS combined) – General Criteria … 4-1 4.2 EVS Specific Criteria … 4-5 4.3 CVS Specific Criteria … 4-7 4.4 EFVS – General and Specific Criteria … 4-8
CHAPTER 5. SYSTEMS INSTALLATION CONSIDERATIONS … 5-1
5.1 EVS/EFVS/CVS Installations Considerations … 5-1 5.2 Continued Airworthiness and Maintenance … 5-2 5.3 EFVS Environmental Specifications … 5-2 5.4 HIRF Considerations for All Installations (EVS, CVS, and EFVS) … 5-2 5.5 Software and Hardware Design Assurance … 5-3 5.6 EVS/EFVS/CVS System Safety Design Criteria … 5-3 5.7 EVS/EFVS/CVS Required Safety Level … 5-3
CHAPTER 6. PERFORMANCE EVALUATION … 6-1
6.1 EVS/EFVS Performance Demonstration … 6-1 6.2 Performance Demonstration of EFVS Landing System … 6-2
APPENDIX A. FAA EFVS 14 CFR COMPLIANCE (PARTIAL LIST) … A-1
APPENDIX B. SAMPLE EFVS FLIGHT TEST CONSIDERATIONS … B-1
APPENDIX C. DETERMINING QUANTIFIED VISUAL ADVANTAGE … C-1
APPENDIX D. SAMPLE AIRPLANE FLIGHT MANUAL (AFM) SUPPLEMENT … D-1
i
TABLE OF CONTENTS
Paragraph Page
APPENDIX E. INSTALLATION OF ENHANCED VISION SYSTEM ON
ROTORCRAFT … E-1
APPENDIX F. DEFINITIONS AND ACRONYMS … F-1
APPENDIX G. RELATED MATERIAL … G-1
FIGURES
Number Page
Figure 2-1. Enhanced Vision Diagram … 2-2
Figure 4-1. Minimum Detection Range … 4-12
Figure B- 1. Depiction of Visual Advantage … B-2
TABLES
Number Page
Table 1-1. Title 14 CFR 91.176 EFVS Visibility and Visual Reference Requirements … 4-11
Table 2-1. System Operating Phases for Considerations … 5-4
Table A-1. EFVS Acceptable Methods of Compliance … A-1
Table B.1. EFVS Flight Test Evaluation Matrix … B-10
Table B.2. EFVS Landing System Supplemental Flight Test Evaluation Matrix … B-12
ii
1.2 Applicability. › 1.2.4 The material contained in this AC does not change or create any…
CHAPTER 1. INTRODUCTION
1.1 Purpose. In this advisory circular (AC), the Federal Aviation Administration (FAA) provides guidance on airworthiness approvals of enhanced vision system (EVS), combined vision system (CVS), and enhanced flight vision system (EFVS) equipment installation. The guidance is performance based and not limited to a specific sensor technology. This action will accommodate future growth in sensor technologies used in vision systems. This guidance was developed primarily for title 14, Code of Federal Regulations (14 CFR) part 25 aircraft. You may also use this guidance for 14 CFR part 23, 27, and 29 aircraft.
Note: As vision system technology advances, applicants are encouraged to propose alternative methods to their AIR certification branch to integrate new and novel safety enhancing vision system functions into their aircraft.
1.1.1 Existing ACs address flight guidance symbology, head-up displays (HUD) and visual display characteristics (for example, AC 25-11B, Electronic Flight Displays, AC 25.1329-1C, Approval of Flight Guidance Systems and AC 23.1311-1C, Installation of Electronic Display in Part 23 Airplanes). For a complete listing of related regulations and guidance, refer to appendices A and G of this AC. This AC complements existing guidance.
1.2 Applicability.
1.2.1 The guidance provided in this AC is for airplane manufacturers, modifiers, foreign regulatory authorities, Federal Aviation Administration (FAA) transport airplane type certification engineers, and FAA designees.
1.2.2 This is a guidance document. Its content is not legally binding in its own right and will not be relied upon by the Department as a separate basis for affirmative enforcement action or other administrative penalty. Conformity with the guidance document is voluntary only. Nonconformity will not affect rights and obligations under existing statutes and regulations.
1.2.3 The FAA will consider other means of demonstrating compliance that an applicant may elect to present. Terms such as “should,” “may,” and “must” are used only in the sense of ensuring the applicability of this particular method of compliance when the acceptable method of compliance in this document is used. If the FAA becomes aware of circumstances in which following this AC would not comply with the applicable regulations, the FAA may require additional substantiation or design changes as a basis for finding compliance.
1.2.4 The material contained in this AC does not change or create any additional regulatory requirement, nor does it authorize changes in, or permit deviations from, existing regulatory requirements.
1.6 Background. › 1.6.1 The revision of AC 20-167A is part of a restructuring of all…
1.3 Cancellation. This AC cancels AC 20-167A, Airworthiness Approval of Enhanced Vision System, Synthetic Vision System, Combined Vision System, and Enhanced Flight Vision System Equipment, dated December 6, 2016.
1.4 Related Material.
1.4.1 This AC provides methods, procedures, and practices acceptable to the FAA for complying with applicable certification regulations. EFVS compliance references are listed in appendix A. The latest version of each AC referenced in this document is available on the FAA website at FAA Advisory Circulars and on the Dynamic Regulatory System.
1.4.2 The preamble accompanying the final rule, Revisions to Operational Requirements for the Use of Enhanced Flight Vision Systems (EFVS) and to Pilot Compartment View Requirements for Vision Systems (81 FR 90126; December 13, 2016) specifically references paragraphs 4.5.3.4, 4.5.3.4.8.4, and 6.2.6.4 of AC 20-167A. These referenced sections equate to sections 4.4.3, 4.4.3.1.8.4, and 6.2.5.4 of this AC, respectively.
1.4.3 Certain material within this AC is based upon RTCA DO-315A, Minimum Aviation System Performance Standards (MASPS) for Enhanced Vision Systems, Synthetic Vision Systems, Combined Vision Systems, and Enhanced Flight Vision Systems. RTCA DO-315A is copyrighted by RTCA, Inc. and used with permission. Purchase information is in appendix G.
1.5 Definition of Key Terms. See appendix F for terms and definitions that apply to this AC.
1.6 Background. This AC is for aircraft manufacturers, modifiers, and type certification engineers seeking certification or installation guidance for visual display systems. Sections 23.2600(a), 25.773, 27.773 and 29.773 address vision systems using a transparent display surface located in the pilot’s outside view, such as a head-up display, head mounted display, or other equivalent display. Such “vision systems” could include any EVS, EFVS, SVS, or CVS.
1.6.1 The revision of AC 20-167A is part of a restructuring of all installation guidance for EVS, EFVS, CVS and synthetic vision systems (SVS). AC 20-167B contains all installation guidance material for EVS, EFVS, and CVS. All installation guidance regarding SVS, synthetic vision guidance systems, and aircraft state awareness synthetic vision systems has been consolidated into AC 20-185A, Airworthiness Approval of Synthetic Vision Systems, Synthetic Vision Guidance Systems, and Aircraft State Awareness Synthetic Vision Systems.
Note: SVS are electronic systems used to display a computer-generated image of the applicable external topography from the perspective of the flightdeck that is derived from aircraft attitude, altitude, position, and a coordinate-referenced database. Since this AC addresses EVS, EFVS, and CVS, installation guidance material for SVS that previously existed in AC 20-167A has been relocated into AC 20-185A.
2.1 Enhanced Vision Systems (EVS). › 2.1.2 The elements of an installed EVS are listed below, with the EVS…
CHAPTER 2. VISION SYSTEMS OVERVIEW
2.1 Enhanced Vision Systems (EVS).
2.1.1 An EVS is an electronic means to provide a display of the forward external scene topography using imaging sensors including forward looking infrared, millimeter wave (MMW) radiometry, MMW radar, and low-light-level image intensifying. EVS does not necessarily provide the additional flight information/symbology on a head-up display (HUD) or equivalent display that is required for EFVS operations under 14 CFR 91.176. While EVS share a similarity with EFVS technology, an EVS does not have to be integrated with a flight guidance system. An EVS may provide additional awareness about the external scene to the pilot, but without the additional capabilities provided by an EFVS, it is not eligible to conduct EFVS operations under § 91.176 (a) or (b).
2.1.2 The elements of an installed EVS are listed below, with the EVS diagram shown in Figure 1:
• EVS sensor system,
• Display processor,
• EVS display,
• Pilot controls/interface, and
• Mounting.
Note 1: While an EFVS contains all the elements of an EVS, for the purposes of this AC, any discussion of an EVS excludes an EFVS.
Note 2: For the purposes of this AC, any guidance that applies to a HUD also applies to displays equivalent to a HUD.
Note 3: A head-worn display (HWD) could potentially meet the requirement for a HUD-equivalent display. The FAA does not currently have any published installation criteria specifically addressing HWDs. Applicants should propose a means of compliance that demonstrates that the proposed HWD is equivalent to a HUD.
2.1.3 EVS sensors are currently categorized as passive or active sensors. › 2.1.3.2 Active Sensors.
Figure 2-1. Enhanced Vision Diagram
Note: Dashed lines and shading represent individual system boundaries for EVS and EFVS.
2.1.3 EVS sensors are currently categorized as passive or active sensors.
2.1.3.1 Passive Sensors. Scene contrast detected by passive infrared sensors can be much different than that detected by natural pilot vision. On a dark night, thermal differences of objects, while not detectable by the naked eye, will be detected depending on the capabilities of an imaging infrared system. However, contrasting colors in visual wavelengths distinguished by the naked eye may not be visible using an imaging infrared system. Sufficient thermal scene contrast allows shapes and patterns of certain visual references to be recognized in the infrared image by the pilot. However, depending on environmental conditions, they can also appear different to a pilot in the infrared image than they would with normal vision.
2.1.3.2 Active Sensors. Scene contrast detected by active systems depends on several parameters: whether the transmitter is centered on the aircraft velocity vector, display updates rates, latency, range resolution, sensitivity, dynamic range, and azimuth and elevation resolution. For an active infrared thermal imaging
2.2 Enhanced Flight Vision Systems (EFVS). › 2.2.3 An EFVS is intended to be used to conduct an operation in which…
sensor, the infrared illuminator has the potential to illuminate more weather obscurations, which can compete with scene contrast and interpretation. One advantage of millimeter wave radar systems is their general immunity to weather obscurations.
2.1.4 Unlike the pilot's external view, the enhanced vision image can be a monochrome, twodimensional display. Some, but not all, of the depth cues found in the natural view are also found in the imagery. The quality of the enhanced vision image and the level of enhanced vision sensor performance depend on atmospheric and external visible and non-visible energy source conditions. Gain settings of the sensor, and brightness or contrast settings of the display, can significantly affect image quality. Certain system characteristics could create distracting and confusing display artifacts.
2.1.5 Unlike with EFVS, an aircraft with EVS does not necessarily provide the additional flight information or symbology required by § 91.176. Unlike an EFVS, an EVS may be displayed on a head down display or on a HUD or equivalent display. The EVS display may not be able to present the image and flight symbology in the same scale and alignment as the outside view. An EVS can provide a display of the external scene topography to the pilot but does not meet the regulatory requirements of § 91.176. An EVS cannot be used as a means to enhance flight visibility or to identify the required visual references in order to gain operational credit and descend below the decision altitude/decision height (DA/DH) or minimum descent altitude (MDA).
2.2 Enhanced Flight Vision Systems (EFVS).
2.2.1 An EFVS is defined in 14 CFR 1.1 as “an installed aircraft system which uses an electronic means to provide a display of the forward external scene topography (the natural or engineered features of a place or region especially in a way to show their relative positions and elevation) through the use of imaging sensors, including but not limited to forward-looking infrared, millimeter wave radiometry, millimeter wave radar, or low-light level image intensification.” An EFVS includes the display element, sensors, computers and power supplies, indications, and controls.
2.2.2 Under § 91.176(a)(1) and § 91.176(b)(1), the EFVS must present EFVS sensor imagery, aircraft flight information, and flight symbology on a head-up display, or an equivalent display, so that the imagery, information and symbology are clearly visible to the pilot flying in their normal position with the line of vision looking forward along the flight path. An equivalent display must be some type of head-up presentation of the required information. A head-down display does not meet the regulatory requirement. For the EFVS monitor display criteria, see sections 4.4.2 and B.10 of this AC.
2.2.3 An EFVS is intended to be used to conduct an operation in which the enhanced vision image is used in lieu of natural vision to perform an approach or landing, determine the enhanced flight visibility, identify required visual references, or conduct a rollout. An EFVS requires a real-time imaging sensor that provides enhanced visibility in low
2.2.5 Under § 91.176(a)(1) and § 91.176(b)(1), the basic elements of an… › 2.2.5.2 The EFVS must present sensor imagery, aircraft flight…
visibility conditions and a level of safety suitable for the proposed operational procedure.
2.2.4 An EFVS with airworthiness approval will be designated as an EFVS approach system or EFVS landing system as described below. Under § 91.176, airworthiness approval being sought by the applicant may require additional basic equipage. Acceptable criteria for EFVS approach systems and EFVS landing systems are discussed in section 4.4 of this AC. EFVS approach systems and EFVS landing systems are briefly described in the following sections:
2.2.4.1 EFVS Approach System. The installed EFVS has been demonstrated to meet an acceptable criteria, such as the criteria described in this AC, for an EFVS approach system to be used to conduct EFVS operations under § 91.176(b). The system design relies on sufficient visibility conditions to mitigate a loss of EFVS function in order to enable unaided flare and rollout. Operational guidance for use of an EFVS is published in AC 90-106B, Enhanced Flight Vision Systems.
2.2.4.2 EFVS Landing System. The installed EFVS has been demonstrated to meet an acceptable criteria, such as the criteria described in this AC, for an EFVS landing system to be used for EFVS operations conducted under § 91.176(a). The system design relies on sufficient visibility conditions to mitigate loss of EFVS function in order to enable unaided flare and rollout. An EFVS that meets the certification criteria for an EFVS landing system also meets the certification criteria for an EFVS approach system. Operational guidance for the use of an EFVS is published in AC 90-106B.
2.2.5 Under § 91.176(a)(1) and § 91.176(b)(1), the basic elements of an installed EFVS are listed below. Guidance on specific system criteria that may be acceptable for an EFVS can be found in Chapter 4 of this AC.
2.2.5.1 The EFVS must have an electronic means to provide a display of the forward external scene topography (the applicable natural or engineered features of a place or region especially in a way to show their relative positions and elevation) through the use of imaging sensors including, but not limited to forward-looking infrared, millimeter wave radiometry, millimeter wave radar, and low-light level image intensification.
2.2.5.2 The EFVS must present sensor imagery, aircraft flight information, and flight symbology on a head-up display, or an equivalent display, so that the imagery, information, and symbology are clearly visible to the pilot flying in their normal position with the line of vision looking forward along the flight path. Aircraft flight information and flight symbology must consist of at least airspeed, vertical speed, aircraft attitude, heading, altitude, command guidance (as appropriate for the approach to be flown),
2.2.6 Enhanced flight vision systems. › 2.2.6.1 Symbology luminates a small fraction of the total display area…
path deviation indications, flight path vector, and flight path angle reference cue. Additionally, for aircraft other than rotorcraft, the EFVS must display a flare prompt or flare guidance when conducting § 91.176(a) operations.
2.2.5.3 The display should meet the following criteria:
2.2.5.3.1 The EFVS must present the displayed EFVS sensor imagery, attitude symbology, flight path vector, flight path angle reference cue (FPARC), command guidance as appropriate and other cues, which are referenced to the EFVS sensor imagery and external scene topography, so that they are aligned with and scaled to the external view.
Note: The European Union Aviation Safety Agency (EASA) imposes additional symbology requirements that are not required by the FAA for certification or for operational approvals. Applicants that will be seeking EASA approval should consult the latest EASA guidance material to ensure compliance with EASA regulations.
2.2.5.3.2 The EFVS must display the FPARC with a pitch scale. The FPARC must be selectable by the pilot to the desired descent angle for the approach and be sufficient to monitor the vertical flight path of the aircraft. The descent angle may also be automatically set to a value found in an onboard database.
2.2.5.3.3 The displayed sensor imagery, aircraft flight information, and flight symbology must not adversely obscure the pilot's outside view or field of view through the flightdeck window.
2.2.5.3.4 The EFVS includes the display element, sensors, computers/power supplies, indications, and controls. It may receive inputs from an airborne navigation system or flight guidance system.
2.2.5.3.5 The EFVS must provide display characteristics, dynamics, and cues suitable for manual control of the aircraft.
2.2.5.3.6 Installations designed to be eligible for EFVS landing system operations must also present a flare prompt or flare guidance and present height above ground level (such as that provided by a radio altimeter or equivalent device). Refer to section 4.4 of this AC for guidance on acceptable performance criteria.
2.2.6 Enhanced flight vision systems. Enhanced flight vision systems display both symbology and imagery.
2.2.6.1 Symbology luminates a small fraction of the total display area of the HUD, leaving much of that area free of symbology and imagery that could interfere with the pilot's view out the window through the display.
2.3 Combined Vision Systems (CVS). › 2.3.2 CVS applicants are expected to meet applicable performance…
2.2.6.2 The EVS image is in the center of the pilot's regulated “pilot compartment view.” In accordance with §§ 23.2600, 25.773(a), 27.773(a), and 29.773(a), the pilot compartment view must be clear, undistorted, and free of glare and reflection that could interfere with the normal duties of the minimum flightcrew. A video image can be more difficult for the pilot to see through than symbols displayed on the HUD. Unlike symbology, the video image illuminates, to some degree, most of the total display area of the HUD with much greater potential interference with the pilot compartment view. The outside scene must be visible, both through and around the display when the EVS image is displayed.
2.2.7 Unlike the pilot's external view, the enhanced flight vision image is historically a monochrome, two-dimensional display. Some, but not all the depth cues found in the natural view are also found in the imagery. The quality of the enhanced flight vision image and the level of enhanced flight vision sensor performance could depend significantly on the atmospheric and external light source conditions. Gain settings of the sensor and brightness or contrast settings of the HUD can significantly affect image quality. Certain system characteristics could create distracting and confusing display artifacts. Finally, this is a sensor-based system that is intended to provide a conformal perspective. Refer to figure 1 for a diagram of the system.
2.2.8 For the primary display, the regulations also make provision for an equivalent display. Section 91.176(a)(1)(i)(B) states that EFVS sensor imagery, aircraft flight information, and flight symbology must be presented “on a head-up display, or an equivalent display, so that the imagery, information and symbology are clearly visible to the pilot flying in their normal position with the line of vision looking forward along the flight path.” To meet part 91 operational requirements, an equivalent display must be some type of head-up presentation of the required information. A head-down display does not meet the operational regulatory requirement. For guidance on monitoring display criteria, see section 4.4.2 of this AC.
2.3 Combined Vision Systems (CVS).
2.3.1 The CVS concept involves a combination of SVS and either EVS or EFVS. Some examples of a CVS include database-driven synthetic vision images combined with real-time sensor images superimposed and correlated on the same display. This includes selective blending of the two technologies based on the intended function of the vision system for which approval is sought. For example, on an approach, most of the arrival would utilize the SVS picture. As the aircraft nears the runway, the picture gradually and smoothly transitions from synthetic to enhanced vision, either for SVS picture validation or displaying the runway environment.
2.3.2 CVS applicants are expected to meet applicable performance criteria for each incorporated system. EVS and EFVS related guidance is located in this document. SVS related guidance can be found in AC 20-185A.
3.2 Intended Function. › 3.2.2 EFVS.
CHAPTER 3. AIRWORTHINESS PACKAGE CONTENTS
3.1 Airworthiness Package. For the purpose of this AC, the applicant should include the following items in the airworthiness package it submits for approval.
• Intended function for the proposed system (See section 3.2 of this AC.)
• General operation for the proposed system (See chapter 4 of this AC.)
• Performance criteria and evaluation plan for the proposed system (See chapter 6 of this AC, and sample test considerations in the appendices.).
• Installation considerations for the proposed system (See chapter 5 of this AC.)
3.2 Intended Function.
3.2.1 EVS or CVS. Define the intended functions of the EVS or CVS. Include what features will be displayed and the criticality of pilot decision-making using the display features under §§ 23.2500, 23.2505, 25.1301, 27.1301, and 29.1301, define additional intended functions (for example, terrain alerting), as appropriate to the aircraft type. It is not acceptable to identify the function of an EVS or CVS display as providing situational awareness only. If the intended function of the CVS is to be used for operational credit, then the CVS must also meet the requirements of an EFVS.
3.2.2 EFVS. Clearly define the intended function of the EFVS (EFVS approach system or EFVS landing system), including whether its use to assess enhanced flight visibility meets or exceeds the required flight visibility of the instrument approach being flown and to visually acquire the visual references required to operate below the DA/DH or MDA as specified in § 91.176(a) and (b). The purpose of an EFVS is to enable flight in the visual segment of an approach when natural flight visibility is not adequate to meet the flight visibility requirements of the instrument approach being flown. In accordance with the operational requirements in § 91.176, an EFVS must demonstrate its ability to provide sufficient enhanced flight visibility and to clearly identify the required visual references at DA/DH or MDA necessary to conduct an EFVS operation.
Note 1: The EFVS is not intended to replace the technologies or procedures already used to safely fly the aircraft down to the DA/DH or MDA.
Note 2: The purpose of an EFVS is to enhance flight visibility for the pilot in a majority of cases/weather and ambient lighting conditions.
Note 3: Past test data obtained by the applicant for an approved EFVS which demonstrated compliance may be considered for inclusion in this airworthiness package if shown to be relevant to the new application using existing practices for establishing similarity of equipment installations from one aircraft to another. For example, if the
Chapter 3. Airworthiness Package Contents › 3.3 Certification of a pre- 14 CFR 91.176 EFVS as an EFVS Landing…
certification project intends to certify a previously approved EFVS approach system as an EFVS landing system, the applicant will need to collect new data to demonstrate the unique aspects of the EFVS landing system and may re-use data collected for the approved EFVS approach system to demonstrate aspects common to both EFVS approach systems and EFVS landing systems. In order to re-use previously collected data the applicant will need to show that the previously collected data is still applicable to the current certification application.
Note 4: Where appropriate, use of technical standard order (TSO) criteria and performance standards can be beneficial to the FAA and the applicant.
3.3 Certification of a pre- 14 CFR 91.176 EFVS as an EFVS Landing System. On December 13, 2016, the FAA published Amendment 91-345 (81 FR 90172) to update then existing §§ 91.175(l) and (m), the prior regulation addressing EFVS use during the segment of an approach that extended from DA/DH or MDA down to 100 feet above the touchdown zone elevation (TDZE). The updated rule expanded the use of EFVS to landings under specified conditions. Section 91.176 was added to cover EFVS use during both landing and approach. Section 91.176(a) addresses EFVS use during landing. The rules for approach that were previously contained in § 91.175(l) and (m) were re-designated as § 91.176(b). EFVS systems that were eligible for operation under §§ 91.175(l) and 91.175(m) are now eligible for § 91.176(b) operations as EFVS approach systems. Systems approved prior to the effective date of § 91.176 (March 13, 2017) must meet the updated applicable airworthiness standards from the rule to be eligible for § 91.176(a) operations as EFVS landing systems. The EFVS landing system application should include the following:
• How the EFVS meets all the requirements of § 91.176(a)(1).
• How the EFVS meets the applicable airworthiness standards for EFVS landing systems as described in AC 20-167B.
Note: Past test data obtained by the applicant for an approved EFVS which demonstrated compliance may be considered for inclusion in this airworthiness package if shown to be relevant to the new application using existing practices for establishing similarity of equipment installations from one aircraft to another.
4.1.3 Intended Function. › 4.1.3.1 The intended function should be reasonable considering the…
CHAPTER 4. SYSTEM CRITERIA
4.1 EVS (or CVS when EVS and SVS combined) – General Criteria. Unless otherwise specified, the EVS/CVS mandatory criteria in this chapter are in accordance with §§ 23.2600(a), 25.773, 27.773 and 29.773. Applicants showing compliance to § 23.2600 should use the criteria found in § 23.773(c), Amendment 23- 63, or ASTM F3117M-24a (or later as stated in the FAA’s part 23.), or propose their own means of compliance.
4.1.1 EVS/CVS Primary Displays. EVS or CVS functionality can be superimposed on the electronic flight instrument system, such as the primary flight display (PFD) as installed in the flightdeck. In this configuration example, the EVS or CVS image can be merged into the sky/ground shading of the attitude direction indicator. In addition to the traditional head-down display PFD, this type of superimposed display could also be associated with a HUD or HUD equivalent display system using EVS or CVS capabilities. Maneuvering the aircraft during any phase of flight (taxi, approach, landing, rollout, etc.) should not be predicated on EVS or CVS imagery alone.
4.1.2 EVS/CVS Secondary Displays. EVS or CVS functionality can be displayed on secondary electronic displays or display windows but is not used for PFD applications. Examples of secondary displays include multi-function displays (MFD), navigation displays, and exocentric displays.
4.1.2.1 The secondary vision system image or loss thereof should not adversely affect other approved secondary display functionality (e.g., navigation display).
4.1.2.2 The secondary display should be such that it cannot be confused with, considered as, or used as a PFD.
4.1.2.3 If primary flight information is presented on a secondary display, the information should be of sufficient quality that it does not cause someone to doubt the PFD data.
4.1.3 Intended Function. Under §§ 23.2500, 23.2505, 25.1301, 27.1301, and 29.1301, the intended function of any installation of EVS/CVS must be clearly defined as appropriate to the aircraft in which the system is being installed. The design and installation safety levels must be appropriate for the stated intended function. Although normally associated with use during flight, utilization of an EVS display during ground operations should not be used if sensor proximity to the taxiway surface causes a distraction.
4.1.3.1 The intended function should be reasonable considering the actual functionality of the installation.
4.1.4 Guidelines for EVS/CVS. › 4.1.4.6 Should display the mode of operation (EVS, or CVS) to the…
4.1.3.2 Operating limitations should be proposed to the FAA by the applicant. In accordance with §§ 23.2620, 25.1581, 27.1581, and 29.1581, operating limitations must be clearly defined and stated in the aircraft’s flight manual supplement in line with the intended function.
4.1.3.3 An EVS that does not meet the requirements in § 91.176 for EFVS operations cannot be used in lieu of natural vision to descend below DA/DH or MDA, regardless of whether it is on a HUD or on a head down display.
4.1.4 Guidelines for EVS/CVS. The proposed system (EVS/CVS):
4.1.4.1 Should have a means to automatically or manually control display brightness.
4.1.4.2 Must not degrade presentation of essential flight information. The pilot’s ability to see and use the required primary flight display information such as primary attitude, airspeed, altitude, and command bars/command guidance must not be hindered or compromised by the EVS/CVS image.
4.1.4.3 Must not distort the pilot compartment view, provide a distorted (i.e., nonconformal) view of the external scene, or interfere with the pilot’s ability to safely perform any maneuvers within the operating limitations of the aircraft, including taxiing, takeoff, approach, and landing if the vision system uses a head-up display or equivalent display. Refer to Society of Automotive Engineers (SAE) design standards for distortion prescribed in SAE Aerospace Standard (AS) 8055A. See section 4.1.5.2 of this chapter for additional HUD or equivalent display criteria.
4.1.4.4 Must not adversely affect any other installed aircraft system. See §§ 23.2500, 23.2505, 25.1301, 27.1301, and 29.1301 for function and installation. See §§ 23.2510, 25.1431, and 29.1431 for electrical equipment.
4.1.4.5 Must perform its intended function in each aircraft environment where system approval is desired. See §§ 23.2500, 23.2505, 25.1301, 27.1301, and 29.1301. For example, if the system is intended to perform in (or after exposure to) known icing conditions, provide a means to keep the EVS sensor window clear of ice accumulation.
4.1.4.6 Should display the mode of operation (EVS, or CVS) to the pilot/flightcrew. Consideration should be given to recording the EVS/CVS display status in a flight data recorder or some form of nonvolatile memory. The modes of the EFVS operation should be made available to the flight data recorder, in addition to all the information required by §§ 23.1459, 25.1459, 27.1459, and 29.1459 or by an operational rule that
4.1.5.1 Primary Flight Display (PFD). › 4.1.5.1.5 The display should not impede a clearly visible zero pitch…
the applicant seeks to show compliance to during certification (e.g. 14 CFR 121.344).
4.1.4.7 Should not have undesirable display characteristics (for example, jitter, jerky motion, and excessive delays.) Refer to SAE design standards for jitter prescribed in SAE AS 8055A.
4.1.5 Display Implementation. EVS/CVS can be incorporated into different display types installed in the flightdeck. AC 25-11B, Electronic Flight Displays, and AC 23.1311-1C, Installation of Electronic Display in Part 23 Airplanes, provide more information on electronic displays. The display is subject to all applicable primary flight information rules and guidance for the category of aircraft.
4.1.5.1 Primary Flight Display (PFD). Primary flight displays are flightdeck displays used to provide information needed to guide and control the aircraft and provide the aircraft altitude, attitude, and airspeed indications. EVS/CVS can be implemented on the primary head down display (HDD) in part 23 and 25 aircraft. Refer to AC 27-1B CHG 1-9, Certification of Normal Category Rotorcraft, and AC 29- 2C CHG 9, Certification of Transport Category Rotorcraft, for guidance on installation on rotorcraft. The following criteria apply to EVS/CVS implemented on a PFD:
4.1.5.1.1 The image, or loss thereof, should not adversely affect the PFD functionality.
4.1.5.1.2 Alignment of imagery presented on the PFD should be consistent with the real world, appropriate for the system’s intended function accounting for possible aircraft attitudes, turbulence, and wind effects, and not mislead the flightcrew. If two displays show EVS or CVS information, or a combination (EVS on one and CVS on another), the orientation of the displays should be the same.
4.1.5.1.3 All spatially referenced symbology must be scaled and aligned within each axis with the imagery so as not to present any misleading information to the pilot.
4.1.5.1.4 The field of regard (FOR) can be variable. However, in accordance with §§ 23.2600, 25.771, 27.771, and 29.771 and §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309, the FOR must be designed to ensure the displayed image is not distracting or misleading and does not adversely affect flightcrew performance and workload.
4.1.5.1.5 The display should not impede a clearly visible zero pitch reference line. The zero pitch reference line should be distinct in visual appearance
4.1.5.2 Head-Up Display or Equivalent Display. › 4.1.5.2.4 Specific design standards for resolution and line width,…
relative to any possible terrain, obstacle, or cultural feature display appearance.
Note: Including a flight path vector or velocity vector to show the pilot the aircraft’s trajectory relative to displayed terrain is recommended.
4.1.5.1.6 Under §§ 23.2600, 25.771, 27.771, and 29.771 and §§ 23.2600(a), 25.773, 27.773, and 29.773, pilot tasks must not be degraded by the displayed imagery. Depending on the intended function of the display information, the imagery must not provide the pilot with misleading information regarding detection, accurate identification, and avoidance of terrain, obstacles, and other flight hazards.
4.1.5.2 Head-Up Display or Equivalent Display.
4.1.5.2.1 A design with EVS/CVS imagery displayed on a HUD must account for the pilot compartment view, including validation that the display of EVS imagery does not conflict with the pilot compartment view.
4.1.5.2.2 The following tasks associated with the use of the pilot’s view should not be degraded below the level of safety that existed without the EVS:
• Detection, accurate identification and maneuvering, as necessary, to avoid traffic, terrain, obstacles, and other hazards of flight; and
• Accurate identification and utilization of visual references required for every task relevant to the phase of flight.
Note: Utilization of video imagery on the HUD or HUD equivalent display during ground operations should not be considered if sensor proximity to the taxiway surface causes distracting imagery.
4.1.5.2.3 Imagery on the HUD or HUD equivalent display must be conformal with the real world and appropriate for the system’s intended function accounting for possible aircraft attitudes, turbulence, and wind effects.
4.1.5.2.4 Specific design standards for resolution and line width, luminance and contrast ratio, chromaticity, and grayscale should be applied. Refer to SAE international design standards for HUD symbology, optical elements and video imagery, which are prescribed in SAE AS 8055A, Minimum Performance Standard for Airborne Head Up Display (HUD), dated July 2015. Recommended best practices can be found in: SAE Aerospace Recommended Practice (ARP) 5288, Transport Category Airplane Head Up Display (HUD) Systems, dated May 2001, and SAE ARP 5287, Optical Measurement Procedures for Airborne Head Up Display (HUD), dated March 1999.
Note: The intellectual property in each of these documents is owned by SAE, (not the FAA), and is subject to change. In general, SAE has a 5year review cycle for each of their documents.
4.2.2 The following are specific criteria for EVS installations: › 4.2.2.3 The display and sensor FOR should be sufficient for the…
4.1.5.3 Secondary displays. EVS/CVS can be implemented with egocentric “inside aircraft” views or exocentric “outside aircraft” viewpoints on head down displays. This includes installed electronic flight bags (EFBs) or MFDs. The following criteria apply to EVS/CVS implemented on secondary displays:
4.1.5.3.1 EVS/CVS image, or loss thereof, must not adversely affect other approved display functionality (such as navigation displays). See §§ 23.2500, 23.2505, 25.1301, 27.1301, and 29.1301.
4.1.5.3.2 The secondary display should be such that it cannot be confused with, considered as, or used as a PFD.
4.1.5.3.3 If primary flight information is presented on a secondary display, it should be of sufficient quality that it does not cause someone to doubt the PFD data.
4.1.5.3.4 The orientation and perspective of the EVS/CVS view should be clear to the pilot. Generally, the orientation of the secondary display should be the same as the orientation of the primary display, to decrease the possibility of pilot confusion.
4.2 EVS Specific Criteria.
4.2.1 An EVS requires a real-time imaging sensor and display, providing improved vision performance. These systems do not qualify for additional operational credit, over and above what is already approved, and are installed on a non-interference basis.
4.2.2 The following are specific criteria for EVS installations:
4.2.2.1 The EVS depiction must be flightcrew de-selectable (if on the primary display, the pilot must be able to easily and quickly remove the sensor image.) For an EVS image displayed on a HUD or HUD equivalent display, the system must provide a means to allow the pilot using the display to immediately deactivate and reactivate the vision system imagery on demand, without removing their hands from the primary flight and power controls, or their equivalent. See §§ 23.2500, 23.2505, and 25.1301, 27.1301, 29.1301, and §§ 23.2600(a), 25.773, 27.773 and 29.773.
4.2.2.2 The display mode (status of EVS), either through flightcrew de-selection or as a result of a failure, should be clearly indicated or obvious to the flightcrew. See §§ 23.2500, 23.2505, and 25.1301, 27.1301, 29.1301, and §§ 23.2600(a), 25.773, 27.773 and 29.773.
4.2.2.3 The display and sensor FOR should be sufficient for the intended functions.
4.2.2 The following are specific criteria for EVS installations: › 4.2.2.7 For display on a HUD or HUD equivalent display, the system…
4.2.2.4 Specific design standards for resolution and line width, luminance and contrast ratio, chromaticity, and grayscale should be applied. Refer to SAE design standards for EVS symbology, optical elements and video imagery are also prescribed in SAE AS 8055A, SAE ARP 5288, and SAE ARP 5287.
4.2.2.5 Consider the following criteria for display characteristics for the EVS design, regardless of the display type:
4.2.2.5.1 For airplanes certificated under part 25, all display characteristics listed in AC 25-11B should be applied. For airplanes certificated under part 23, all display characteristics listed in AC 23.1311-1C should be applied. For rotorcraft certificated under part 27 or 29, all display characteristics listed in AC 27-1B CHG 1-9 or AC 29-2C CHG 9 (respectively), should be applied. For other aircraft without corresponding criteria, the guidance in AC 25-11B or AC 23.1311-1C serves as recommended guidance.
4.2.2.5.2 The display should not have undesirable display characteristics (such as blooming, fixed pattern noise and running water). Refer to SAE design standards for display characteristics prescribed in SAE AS 8055A.
4.2.2.6 Consider the following criteria for image characteristics for the EVS design:
4.2.2.6.1 On an HDD, the relationship of the display FOR to the actual field of view should be suitable for the pilot to smoothly transition from the HDD to the out-the-window real world view or HUD or HUD equivalent display. Minification up to a ratio of 3:1 has been shown to be acceptable.
4.2.2.6.2 The image data should be refreshed at 15 Hz or better.
Note: Refresh rates above 50 Hz for cathode ray tube (CRT) based HUDs may be required to prevent unacceptable levels of flicker. Refer to SAE AS 8055A.
4.2.2.6.3 The image latency should be less than 100 milliseconds, where the latency is measured from the image source time of applicability to the display of the image.
Note: An EVS display refresh rate equal to or greater than 15 Hz has been found to be acceptable. Any lag introduced by the display system should be consistent with the aircraft control task associated with that parameter.
4.2.2.7 For display on a HUD or HUD equivalent display, the system should provide a control of the EVS display contrast/brightness which is effective in dynamically changing background (ambient) lighting. The minimum system should not:
4.3 CVS Specific Criteria. › 4.3.2 The CVS should meet the detailed performance criteria for EVS…
• Distract the pilot;
• Impair the pilot’s ability to detect and identify visual references;
• Mask flight hazards; or
• Degrade task performance or safety.
4.2.2.8 When an EVS is incorporated on the primary flight display, the EVSbased primary display should be clear and unambiguous when recovery from unusual attitudes is required. An accurate, easy, quick-glance interpretation of attitude should be possible for all unusual attitude situations and other “non-normal” maneuvers sufficient to permit the pilot to recognize the unusual attitude and initiate a recovery within one second. We recommend the use of chevrons or pointers on all attitude indications to perform effective manual recovery from unusual attitudes. (For airplanes certificated under part 25, refer to AC 25-11B).
4.3 CVS Specific Criteria.
4.3.1 CVS requires a real-time imaging sensor and display that provides demonstrated vision performance for its intended function. It also requires a terrain and obstacle database and a precision navigation position for the synthetic portion of the display. The design assurance levels should be appropriate for the system’s intended function. The following criteria apply to CVS installations:
4.3.1.1 CVS should meet the respective criteria of the EVS and SVS implementations. Installation guidance for SVS displays can be found in AC 20-185A.
4.3.1.2 The EVS and SVS depictions should be conformal with each other.
4.3.1.3 Fusion of EVS and SVS should require the images to be aligned within 5 milliradian (mrad) laterally and vertically at the boresight of the display. Therefore, blended EVS and SVS images should not cause confusion to the flightcrew. Significant image discrepancies between EVS and SVS due to failure conditions should be obvious to the flightcrew.
Note: It is difficult to define every implementation in order to determine what is “significant.” However, the applicant is expected to reduce discrepancies to as near-zero as possible. The final determination will occur during flight test.
4.3.2 The CVS should meet the detailed performance criteria for EVS specified in sections 4.2 and 4.3 of this chapter and SVS performance criteria listed in AC 20-185A.
4.4.1 If the intended function of the EFVS is to meet § 91.176, the EVS… › Note
4.4 EFVS – General and Specific Criteria.
4.4.1 If the intended function of the EFVS is to meet § 91.176, the EVS criteria above as well as the following EFVS general and specific criteria, are applicable to the EFVS:
4.4.1.1 Under §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309, the design assurance level of the aircraft systems must be commensurate with the identified failure probabilities.
4.4.1.2 The sensor image, combined with the required aircraft state and position reference symbology, must be presented to the flightcrew on the HUD, or an equivalent display, so that they are clearly visible to the pilot flying in their normal position and line of vision looking forward along the flight path. For HUD or HUD equivalent display operations, the pilot flying views the EFVS sensor and symbolic information that is properly aligned and registered to enable a one-to-one (conformal) overlay with the actual external scene. See SAE AS8055A criteria on conformality.
4.4.1.3 The HUD or HUD equivalent display and displayed FOR must be sufficient for the EFVS information to be displayed conformally over the range of anticipated aircraft attitudes, aircraft configurations, and environmental (for example, wind) conditions. The aircraft state and position reference data must be presented in the form of symbology overlaying the image presentation. Section 91.176(a)(1)(B) requires the following flight instrument data on the HUD, or HUD equivalent display:
• Airspeed;
• Vertical speed;
• Aircraft attitude;
• Heading;
• Altitude;
• Command guidance as appropriate for the approach to be flown;
• Path deviation indications;
• Flight path vector; and
• Flight path angle reference cue.
Note: EASA has additional symbology requirements that are not required by the FAA for EFVS certification or for operational approvals. Applicants that will be seeking EASA approvals should consult the latest EASA guidance material to ensure compliance with EASA regulations.
4.4.1 If the intended function of the EFVS is to meet § 91.176, the EVS… › 4.4.1.8 The minimum system should include a control of EFVS display…
4.4.1.4 In addition to criteria in 4.4.1.3, the following specified aircraft flight information required for operation by § 91.176(a)(1)(i)(B) must also be displayed for an EFVS landing system:
• Height above ground level such as that provided by a radio altimeter or other device capable of providing equivalent performance; or
• For aircraft other than rotorcraft, flare prompt or flare guidance for achieving acceptable touchdown performance, as discussed in section 6.2.
4.4.1.5 Flare Cue. Under § 91.176(a)(1)(i)(B), an EFVS landing system for aircraft other than rotorcraft must have a flare cue because it is intended to enable landing in low visibility. The flare cue, whether a flare prompt or flare guidance, should demonstrate that it meets the landing criteria found in section 6.2. For some aircraft, flare guidance may be necessary because a flare prompt is not sufficient.
4.4.1.6 Flare Prompt. The flare prompt indicates to the pilot when to initiate the flare but does not provide direction/guidance on how to execute the flare maneuver. The flare prompt should be presented at an appropriate time and with sufficient saliency so that the flare maneuver will be neither too early nor too late and within the touchdown zone as described in section 6.2 of this AC. The appearance and dynamic behavior of the flare prompt should be distinguishable from command guidance.
4.4.1.7 Flare Guidance. Flare guidance provides explicit command guidance to the pilot for when to initiate the flare and provides directional cues on how to execute the flare maneuver. The flare guidance directs the flare maneuver so that the flare would be neither too early nor too late, and within the touchdown zone as described in section 6.2 of this AC.
4.4.1.8 The minimum system should include a control of EFVS display contrast/ brightness, for manually controlled EFVS systems, and should include a control for automatic EFVS systems that is effective in dynamically changing background (ambient) lighting, prevents distractions to the pilot, prevents impairment of the pilot’s ability to detect and identify visual references, prevents masking of flight hazards, and prevents other negative impacts on task performance or safety. If automatic control for image brightness is not provided, it should be shown that manual setting of image brightness meets the above criteria and does not cause excessive workload.
4.4.1 If the intended function of the EFVS is to meet § 91.176, the EVS… › 4.4.1.11 Under § 91.176, upon reaching the DA/DH or minimum descent…
4.4.1.9 Under §§ 23.2600(a), 25.773(e)(3), 27.773(c)(3), and § 29.773(c)(3), the EFVS display controls must be visible to and within reach of the pilot flying, from any normal seated position with the seat belt and shoulder harness (if applicable) fastened. If each pilot station is equipped with EFVS, the EFVS display controls must be visible to, and within reach of each pilot from any normal seated position. The position and movement of the controls must not lead to an inadvertent operation. The EFVS controls, except those located on the pilot’s flight controls, must be adequately illuminated for all normal background lighting conditions, and must not create any objectionable reflections on the HUD or HUD equivalent display or other flight instruments. There must be a means to allow the pilot using the display to immediately deactivate and reactivate the vision system imagery on demand, without removing their hands from the primary flight and power controls, or their equivalent.
4.4.1.10 The approach path situation references and command guidance should be based on the specific navigation source for the straight-in instrument approach procedure in use.
4.4.1.11 Under § 91.176, upon reaching the DA/DH or minimum descent altitude (MDA), the required visual references presented in Table 1 must be distinctly visible and identifiable to the pilot. Sensor performance criteria can be quantified in terms of the range of the enhanced flight visibility compared to the flight visibility when low visibility conditions exist (See appendix C, “Determining Quantified Visual Advantage”). The visual references of the runway environment must be seen by the sensor at or beyond the distance required in the visual segment of the instrument approach being flown.
Table 1-1. Title 14 CFR 91.176 EFVS Visibility and Visual Reference
Requirements.
From the authorized DA/DH to 100 feet height above TDZE of the runway of intended landing, the approach light system (if installed) or both the runway threshold and the touchdown zone are distinctly visible and identifiable to the pilot using an EFVS.
1. Under § 91.176, the pilot must identify the runway threshold using at least one of the following visual references:
a. The beginning of the runway landing surface; or
b. The threshold lights; or
c. The runway end identifier lights.
2. Under § 91.176, the pilot must identify the touchdown zone using at least one of the following visual references:
d. The runway touchdown zone landing surface; or
e. The touchdown zone lights; or
f. The touchdown zone markings; or
g. The runway lights.
At 100 feet height above touchdown zone elevation of the runway of intended landing and below that altitude, the enhanced flight visibility using EFVS is sufficient for one of the following visual references to be distinctly visible and identifiable to the pilot. For EFVS approach system operations the following features must be identified without reliance on the EFVS approach system. For EFVS landing and rollout operations the following listed features may be identified using an EFVS landing system:
1. The runway threshold; or
2. The lights or markings of the threshold; or
3. The runway touchdown zone landing surface; or
4. The lights or markings of the touchdown zone.
4.4.1 If the intended function of the EFVS is to meet § 91.176, the EVS… › 4.4.1.13 Under §§ 23.2600(a), 25.773, 27.773, and 29.773, the EFVS…
4.4.1.12 The minimum detection EFVS range (figure 4-1) can be derived by using an assumed minimum distance of the aircraft at the nominal Category I (200 ft.) DA/DH before which the EFVS should image the runway threshold. On a 3 degree glideslope, the horizontal distance from the aircraft to the runway threshold is approximately 2,816 feet (3,816 feet from the precision aim point markings). In all cases, in accordance with § 91.176(a)(3), the EFVS must provide sufficient enhanced visibility at the DA/DH or MDA equal to the prescribed visibility of the instrument approach being conducted. These values do not take into account pilot decision time or actual atmospheric conditions. However, the use of nonprecision approaches can require greater distances, or initiating approaches with higher DAs, DHs, or MDAs.
Figure 4-1. Minimum Detection Range
4.4.1.13 Under §§ 23.2600(a), 25.773, 27.773, and 29.773, the EFVS imagery displayed on the HUD or HUD equivalent display must account for the pilot compartment view requirements, including validation that the display of imagery does not conflict with the pilot compartment view. The display of EFVS sensor imagery must be on a system that compensates for the interference caused by the provided imagery. Additionally, the system must provide an undistorted and conformal view of the external scene, and a means to deactivate the display that does not restrict the pilot from performing specific maneuvers. The following tasks associated with the use of the pilot’s view must not be degraded below the level of safety that existed without the video imagery:
• Detection, accurate identification and maneuvering, as necessary to avoid traffic, terrain, obstacles, and other hazards of flight; and
4.4.2 EFVS Display Criteria. › 4.4.2.3 Current FAA guidelines for HUDs apply with respect to EFVS.
• Accurate identification and utilization of visual references required for every task relevant to the phase of flight.
Note: Utilization of video imagery on the HUD or HUD equivalent display during ground operations should not be considered if sensor proximity to the taxiway surface causes distracting imagery.
4.4.2 EFVS Display Criteria. Unless otherwise specified, §§ 23.2600(a), 25.773, 27.773 and 29.773 serve as the regulatory bases for the EFVS mandatory display criteria in this section.
4.4.2.1 For EFVS implemented on a HUD, the image should be compatible with the field of view (FOV) and head motion box of a HUD designed against SAE ARP 5288 (transport category head-up display (HUD) systems), or an equivalent standard. When used in a given phase of flight, the HUD and EFVS FOR must provide a conformal image with the visual scene over the range of aircraft attitudes and wind conditions. A display that provides the pilot monitoring with EFVS sensor imagery is not required for EFVS approach system operations. However, in accordance with § 91.176(a)(1)(ii) for EFVS landing system operations, when a minimum flightcrew of more than one pilot is required for the conduct of the operation, the aircraft must be equipped with a display that provides the pilot monitoring with EFVS sensor imagery. Under §§ 23.2500, 25.1321, 27.1321, and 29.1321, all displays used to monitor the approach must be located in the flightdeck so that either pilot seated at the controls can monitor the airplane’s flight path and instruments with minimum head and eye movement. Any symbology displayed should not adversely obscure the sensor imagery of the runway environment.
4.4.2.2 Under 14 CFR parts 21, 23, 25, 27, and 29, the EFVS display must meet applicable airworthiness certification requirements (See appendix A). Some of these requirements could be specific to EFVS and could be in addition to all other requirements applicable to the HUD and the basic avionics installation.
4.4.2.3 Current FAA guidelines for HUDs apply with respect to EFVS. These criteria include well-established military and civil aviation standards for HUDs as defined in MIL-STD-1787D, Aircraft Display Symbology, and AC 25-11B. Specific design standards for image size, resolution and line width, luminance and contrast ratio, chromaticity, and grayscale should be applied. SAE design standards for HUD symbology, optical elements, and video imagery are also prescribed within SAE AS 8055. Recommended practices are included in SAE ARP 5288 and SAE ARP 5287.
4.4.2 EFVS Display Criteria. › 4.4.2.5 The EFVS installation and image should have an effective…
4.4.2.4 The EFVS installation and the EFVS image, when superimposed on the HUD symbology must:
4.4.2.4.1 Under § § 23.1301 25.1301, 27.1301 29.1301 and 23.1309, 25.1309, 27.1309 and 29.1309, be suitable for and successfully perform its intended function.
4.4.2.4.2 Allow the accurate identification and utilization of visual references, using both EFVS and natural vision, as appropriate.
4.4.2.4.3 Under § § 23.1301 25.1301, 27.1301 29.1301 and 23.1309, 25.1309, 27.1309 and 29.1309, have acceptable display characteristics to accomplish the intended function.
4.4.2.4.4 Have a means to allow the pilot using the display to immediately deactivate and reactivate the vision system imagery on demand, without removing their hands from the primary flight and power controls, or their equivalent.
4.4.2.4.5 Not degrade presentation of essential flight information on the HUD. The pilot's ability to see and use the required PFD information such as primary attitude, airspeed, altitude, and command bars must not be hindered or compromised by the EFVS image on the HUD.
4.4.2.4.6 Under § § 23.2600, 25.771(a), 27.771(a), 29.771(a) and 25.1302(b), not be misleading, cause confusion, or significantly increase pilot workload.
4.4.2.4.7 Be aligned with and scaled to the external scene.
4.4.2.4.8 Not cause unacceptable interference with the safe and effective use of the pilot compartment view.
4.4.2.4.9 Under § § 23.2600, 25.771(a), 27.771(a), 29.771(a) and 25.1302(b), not alter external scene colors in a way that causes confusion, significantly increases workload and/or prevents the pilot from performing any required tasks (e.g., discerning precision approach path indicators).
4.4.2.4.10 Allow the pilot to recognize significantly misaligned or non-conformal conditions to the external scene that may preclude the pilot’s performance of any required maneuvers.
4.4.2.5 The EFVS installation and image should have an effective control of EFVS display brightness without causing excessive pilot workload and not cause adverse physiological effects such as fatigue or eyestrain.
4.4 EFVS – General and Specific Criteria. › 4.4.3 EFVS Detailed System Criteria.
4.4.2.6 A HUD modified to display EFVS must continue to meet the conditions of the original approval and be adequate for the intended function, in all phases of flight in which the EFVS is used. An accurate, easy, quickglance interpretation of attitude should be possible for all unusual attitude situations and other “non-normal” maneuvers to permit the pilot to recognize the unusual attitude and initiate recovery within one second. The use of chevrons, pointers, and/or permanent ground-sky horizon on all attitude indications to perform effective manual recovery from unusual attitudes has been shown to be an acceptable means to aid in recovery from unusual attitudes. Refer to AC 23.1311-1C, AC 25-11B, AC 27-1B CHG 1-9 and AC 29-2C CHG 9 for guidance on electronic flightdeck displays.
4.4.2.7 Under § 91.176 the EFVS must display a flight path vector (FPV) and flight path angle reference cue (FPARC) on the HUD or HUD equivalent display. The following criteria apply to these symbols:
4.4.2.7.1 The position and motion of the FPV should correspond to the aircraft’s earth-referenced flight path vector. The display should provide for a FPV depiction when at the limit of the FOR.
4.4.2.7.2 The dynamic response of the FPV should not exhibit undue lag or overshoot due to pilot control inputs. If flight path vector quickening is used, adequate testing should demonstrate that the quickening employed actually improves performance and does not introduce any undesirable dynamics to the display. Refer to AC 25-11B, paragraphs A.7 and F.5.4.5;
4.4.2.7.3 The display of the FPARC should be suitable for monitoring the vertical flight path of the aircraft.
4.4.2.7.4 The system must provide the pilot a means to select the desired descent angle that is represented by the FPARC and may also provide a means for the descent angle to be selected automatically from a database.
4.4.2.8 The display of attitude symbology, FPV, FPARC, and other visual elements which are earth-referenced must be aligned with and scaled (i.e., conformal) to the external view.
4.4.2.9 The EFVS display of imagery, flight information and flight symbology should be a suitable visual reference for the pilot during the manual performance of any maneuvers within the operating limitations of the aircraft, including taxiing, takeoff, approach, landing and rollout.
4.4.3 EFVS Detailed System Criteria. The performance of EFVS imaging systems does not solely depend upon system design, but also depends upon the target scene characteristics such as the runway, light structures, electromagnetic radiation, and atmospheric conditions.
4.4.3.1 Minimum System Performance. › 4.4.3.1.2 EFVS FOR.
4.4.3.1 Minimum System Performance. Integration of the major components includes the installed sensor, its interconnections with the sensor display processor, the display device, pilot interface, and aircraft mechanical interface, which can include the radome for the sensor.
4.4.3.1.1 Latency. EFVS latency should be no greater than 100 milliseconds (msec). A longer lag time can be found satisfactory, provided it is demonstrated not to be misleading or confusing to the pilot. Latency should not be discernible to the pilot and should not affect control performance or increase pilot workload. At best, EFVS latency causes undesirable oscillatory image motion in response to pilot control inputs or turbulence. At worst, EFVS latency may cause pilot-induced oscillations if the pilot attempts to use the EFVS for active control during precision tracking tasks or maneuvers in the absence of other visual cues.
4.4.3.1.2 EFVS FOR. The minimum fixed FOR should be 20 degrees horizontal and 15 degrees vertical. In applications where the FOR is centered on the flight path vector, the minimum FOR should be 5 degrees (± 2.5 degrees) vertical and 20 degrees horizontal.
1. The minimum EFVS FOR should not only consider the HUD FOV (i.e., how large of an area displayed), but also the area over which this area subtends (i.e., what is shown on the conformal display). The FOR portrayed on the HUD is established by three primary determinants:
• HUD and EFVS sensor field-of-view;
• Orientation of the HUD with respect to the aircraft frame of reference (for example, boresight and proximity to pilot’s eye); and
• Orientation (for example, attitude) of the aircraft.
2. The EFVS image should be compatible with the field-of-view and head motion box of a HUD designed against SAE ARP 5288, or equivalent standard. The HUD and EFVS FOR should provide a conformal image with the visual scene over the range of aircraft attitudes and wind conditions for each mode of operation. Limitations should be clearly specified in the aircraft flight manual (AFM) if the HUD cannot be used throughout the full aircraft flight envelope.
3. A variable FOR is permissible, assuming a slewable sensor (i.e., variable field-of-regard), centered on the flight path vector, with a minimum +/ 2.5 degrees about the flight path vector to allow for momentary flight path perturbations and to allow sufficient fore/aft view of the required visual references.
4.4.3.1 Minimum System Performance. › 4.4.3.1.7 Image conformality.
4.4.3.1.3 Off-axis rejection. A source in object space greater than 1 degree outside the FOV should not result in any perceptible point or edge-like image within the field of view. The EFVS should preclude off-axis information from folding into the primary FOR imagery and creating the potential for misleading or distracting imagery.
4.4.3.1.4 Jitter. When viewed from the HUD eye reference point, the displayed EFVS image jitter amplitude should be less than 0.6 mrad when installed on the aircraft. Jitter for this use is defined in SAE ARP 5288. This implies that the EFVS and HUD cannot exhibit jitter greater than that of the HUD itself.
4.4.3.1.5 Flicker. Flicker is brightness variations at a frequency above 0.25 Hz per SAE ARP 5288. The minimum standard for flicker should meet the criteria of SAE ARP 5288, or equivalent. Flicker can cause mild fatigue and reduced flightcrew efficiency. In accordance with §§ 23.2600(a), 25.773, 27.773 and 29.773, the EFVS and HUD cannot exhibit flicker greater than that of the HUD itself.
4.4.3.1.6 Image artifacts. The EFVS must not exhibit any objectionable noise, local disturbances, or an artifact that prevents the system from meeting its intended function. The EFVS design should minimize display characteristics or artifacts (for example, internal system noise, fixed pattern noise, or running water droplets) which obscure the desired image of the scene, impair the pilot's ability to detect and identify visual references, mask flight hazards, distract the pilot, or otherwise degrade task performance or safety. See §§ 23.2600(a), 25.773, 27.773 and 29.773.
4.4.3.1.7 Image conformality. The accuracy of the integrated EFVS and HUD image should not result in a greater than 5 mrad display error at the center of the display at a range of 2000 ft (100 ft altitude on a 3 degree glideslope). Under SAE ARP 5288, the total HUD system display accuracy error, as measured from the HUD eye reference point, should be less than 5 mrad at the HUD boresight, with increasing error allowable toward the outer edges of the HUD. Errors away from the boresight should be as defined in SAE ARP 5288, or an equivalent standard. The primary EFVS error components include the installation misalignment of the EFVS sensor from aircraft/HUD boresight and sensor parallax. A range parameter is used in the EFVS conformability requirement to account for the error component associated with parallax. There is no boresight error allowed for the EFVS sensor, since it is assumed any error can be electronically compensated during
4.4.3.1 Minimum System Performance. › 4.4.3.1.8 Sensor/sensor processor.
installation. With EFVS operations, the aircraft is essentially flown irrespective of the EFVS/HUD dynamic error, to the MDA or DA/DH. From this point to 100 ft. height above touchdown zone elevation, the EFVS conformality error introduces error in the pilot’s ability to track along the extended centerline/vertical glide path as the pilot flies the flight path vector and glidepath reference line toward the EFVS image of the runway.
4.4.3.1.8 Sensor/sensor processor.
1. Dynamic range.
The minimum required dynamic range for passive EFVS should be 48 db. For active EFVS, side lobes should be 23 db below the main beam, and 40 db dynamic range plus sensitivity time control.
2. Sensor image calibration.
Visible image calibrations and other built-in tests that cannot be achieved within a total latency of 100 milliseconds should occur only on either pilot command or be coordinated by aircraft data to only occur in non-critical phases of flight. If other than normal imagery is displayed during the nonuniformity correction (NUC) or other built-in tests, the image must be removed from the pilot’s display in order to comply with §§ 23.2600(a), 25.773, 27.773 and 29.773. This prohibits excessive times to complete maintenance or calibration functions which would remove or degrade the EFVS imagery during critical phases of flight, unless the pilot commands the action (with full knowledge of effect, based on training and experience). Abnormal imagery should be removed from the display to eliminate the potential for any misleading information.
3. Sensor resolution.
As a minimum, EFVS resolution performance must adequately resolve (for pilot identification) the runway threshold and the touchdown zone to enable the intended function. See §§ 23.2500, 23.2505, and 25.1301, 27.1301, and 29.1301. For example, an EFVS should resolve a 60 ft wide runway from 200 ft above touchdown zone elevation with a typical 3degree glideslope. The sensor resolution was established by providing this resolution at a minimum range, allowing the pilot to continue the descent below DA/DH or MDA. (These values do not take into account pilot decision time or actual atmospheric conditions, or the use of non-precision approaches that may require greater distances.) A 60 ft.-wide runway was chosen as the International Civil Aviation Organization (ICAO) minimum runway width to support an instrument approach procedure.
4. Passive sensor optical distortion.
Optical distortion should be 5 percent or less across the minimal FOR as defined in section 4.4.3.1.2 and no greater than 8 percent outside the minimal FOR.
5. Sensor sensitivity.
In this context, the EFVS sensor sensitivity should be at least a noise equivalent temperature difference (NETD) of 50 degrees mK tested at an appropriate ambient temperature for passive EFVS systems, or -20dB sm/sm (square meter/square meter) surface at Rmax from 200 ft height above touchdown zone elevation with a typical 3-degree glideslope for active EFVS systems. Passive sensors for different visible or short-wave infrared sources can require very sensitive detectors, as specified by low noise equivalent powers.
6. Failure messages.
EFVS malfunctions detected by the system, and which can adversely affect the normal operation of the EFVS, should be annunciated. As a minimum, specific in-flight failure message(s) for sensor failure and frozen image must be displayed to the flightcrew. See §§ 23.2500, 23.2505, 25.1309, 27.1309, 29.1309 and AC 25-11B, appendix F.
7. Blooming.
The sensor should incorporate features to minimize blooming, which can create an unusable or objectionable image. Objectionable blooming is defined as the condition that obscures the required visual cues specified in Table 1. Blooming to the extent the required visual references are no longer distinctly visible and identifiable is unacceptable.
8. Image persistence.
The image persistence time constant should be less than 100 milliseconds. However, burn-in or longer image persistence caused by high energy sources (for example, the sun saturating the infrared sensor elements), should be removed from the image to meet the provisions of section 4.4.3.1.6 by a secondary on-demand process (for example, the NUC process).
9. Dead pixels.
Dead pixels or sensor elements replaced by a “bad pixel” replacement algorithm should be limited to 1 percent average of the total display area, with no cluster greater than 0.02 percent within the minimum FOR. A small number of disparate dead pixel elements can be effectively replaced by image processing, but the algorithms will eventually degrade the image quality and accuracy due to the sheer number and closely-spaced location of the elements.
10. Parallax.
The effects of parallax caused by lateral, vertical, and longitudinal offset of the sensor from the pilots’ design eye points must not impede the EFVS from performing its intended function, as evaluated during flight test. See §§ 23.2500, 23.2505, 25.1301, 27.1301, and 29.1301. Parallax should not degrade landing performance parameters (e.g., flare height, sink rate,
touchdown location, and groundspeed during landing, exit and taxi) between EFVS operations and visual operations in the same aircraft.
5.1 EVS/EFVS/CVS Installations Considerations. › 5.1.2 EFVS Fail Safe Features.
CHAPTER 5. SYSTEMS INSTALLATION CONSIDERATIONS
5.1 EVS/EFVS/CVS Installations Considerations.
5.1.1 EVS/EFVS/CVS Pilot Controls and Annunciations.
5.1.1.1 The EVS/EFVS/CVS display controls should be visible to and within reach of the pilot flying from any normal seated position. The position and movement of the controls should not lead to inadvertent operation.
5.1.1.2 The EVS/EFVS/CVS controls, except those located on the pilot’s control inceptor (e.g., control wheel, yoke, stick, etc.), should be adequately illuminated for all normal background lighting conditions and should not create any objectionable reflections on other flight instruments. See §§ 23.2600(a), 25.773, 27.773 and 29.773.
5.1.1.3 There should be a means to manually modulate illumination unless fixed illumination of the EVS/EFVS/CVS controls is shown to be satisfactory under all lighting conditions. See §§ 23.2600(a), 25.773, 27.773 and 29.773.
5.1.1.4 Any modes of EFVS operation should be annunciated on the flightdeck and visible to the flightcrew. The modes of the EFVS operation should be made available to the flight data recorder, in addition to all of the information required by §§ 23.1459, 25.1459, 27.1459, and 29.1459, or by an operational rule that the applicant seeks to show compliance to during certification (e.g. 14 CFR 121.344).
5.1.2 EFVS Fail Safe Features. The normal operation of the EFVS should not adversely affect or be adversely affected by other normally operating aircraft systems. Under §§ 23.1309, 25.1309, 27.1309, 29.1309, the flightcrew must be alerted through annunciation (or other means of providing warning information) to any detected malfunctions of the EFVS which could cause display of misleading information, and the misleading information should be removed. Alerting annunciations should be displayed to the flightcrew in accordance with AC 23.1311-1C, AC 25.1322-1, AC 25-11B, AC 27-1B CHG 1-9 and AC 29-2C CHG 9, as applicable. Under §§ 23.2500, 23.2505, 25.1309, and 27.1309, the applicant must assess the criticality of the EFVS’s function to display imagery, including the potential to display hazardously misleading information. Likewise, the assessment must include the hazardous effects of any malfunction of the EFVS that could adversely affect interfaced equipment or associated systems. See AC 23-1309-1E, AC 25-11B, and Army Reserve Aviation Command (ARAC)-recommended 25.1309 and Arsenal Guidance, AC 27-1B CHG 1-9 and AC 29-2C CHG 9. This requirement should be met through a system safety assessment (SSA) and documented via fault tree analysis (FTA), failure mode and effects analysis (FMEA), and FMEA substantiation, or equivalent safety documentation.
Chapter 5. Systems Installation Considerations › 5.4 HIRF Considerations for All Installations (EVS, CVS, and EFVS).
5.1.3 The electrical system must be able to furnish the required power at the proper voltage for the EVS/CVS. See §§ 23.2525, 25.1310, 27.1351 and 29.1351.
5.1.4 EVS/EFVS/CVS Built-In Test (BIT). The applicant should provide a BIT capability that, at a minimum, limits the exposure time to latent failures consistent with the exposure limits in the SSA.
5.2 Continued Airworthiness and Maintenance.
5.2.1 Under § 23.1529, 25.1529, 27.1529, and 29.1529, the applicant must develop instructions for continued airworthiness for maintaining the EVS/CVS/EFVS and its components.
5.2.2 Under § 21.50, Instructions for Continued Airworthiness (ICA) must be furnished after final design approval. Refer to FAA Order 8110.54A, Instructions for Continued Airworthiness, for additional guidance on FAA’s procedures for administering ICA requirements.
5.2.3 Other maintenance tasks may be developed as a result of the safety assessment, design reviews, manufacture’s recommendations and Maintenance Steering Group 3 (MSG-3) analyses that are conducted. These instructions include but are not limited to removal and replacement, troubleshooting, cleaning, maintenance procedures for the MEL relief and software loading/configuration control.
5.3 EFVS Environmental Specifications. Applicants should follow the guidance in AC 21-16G (as revised), and RTCA DO-160 versions D, E, F and G, Environmental Conditions and Test Procedures for Airborne Equipment. Additionally, under §§ 23.2520, 25.1316, 25.13l7, 27.13l7, 29.1316, or 29.1317, or related special conditions, the EFVS must also meet the high-intensity radiated fields (HIRF), electromagnetic interference, and lightning requirements as specified in the certification basis of the aircraft in which the EFVS is to be installed.
5.4 HIRF Considerations for All Installations (EVS, CVS, and EFVS). Under §§ 23.2520, 25.13l7, 27.13l7, or 29.1317, the immunity of critical avionics/electronics and electrical systems to HIRF must be established. Critical avionics/electronics and electrical system functions are those whose failure would contribute to or cause a failure condition that would prevent the continued safe flight and landing of the aircraft. Refer to AC 20-158A, The Certification of Aircraft Electrical and Electronic Systems for Operation in the High-Intensity Radiated Fields (HIRF) Environment, for additional guidance.
5.7 EVS/EFVS/CVS Required Safety Level. › 5.7.3 Rotorcraft.
5.5 Software and Hardware Design Assurance.
5.5.1 Follow the guidance in AC 20-115D, Airborne Software Development Assurance Using EUROCAE ED-12 and RTCA DO-178 to develop software. Use the version which is current at time of application.
5.5.2 Follow the guidance in AC 20-152, RTCA, Inc., Document RTCA/DO-254, Design Assurance Guidance for Airborne Electronic Hardware, to develop your airborne electronic hardware, if applicable. Use the version which is current at time of application.
5.6 EVS/EFVS/CVS System Safety Design Criteria. A complete functional hazard assessment (FHA) and SSA should be conducted to identify failure modes and classify the hazard levels. Under §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309, the ability of the system design to perform its intended function must be demonstrated through analysis and engineering tests to preclude failures that can cause hazardously misleading information to be presented to the pilot or the flightcrew, or which can otherwise subsequently cause an unsafe condition. The following guidelines do not preclude the results of a full SSA. The results of an SSA found acceptable to the FAA should prevail.
5.7 EVS/EFVS/CVS Required Safety Level. Under §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309, the applicant must perform a safety assessment based on the proposed installation for the given aircraft and intended function for each phase of flight. The SSA should address both the loss and the incorrect display of information, including hazardously misleading information. The hazard effects of all malfunction of the EVS/EFVS/CVS that could adversely affect interfaced equipment or associated systems should be determined and assessed according to the applicable certification rules and associated advisory materials.
5.7.1 Transport Category Airplanes. Section 25.1309 defines the safety requirement, and ARAC-recommended § 25.1309 and Arsenal Guidance provide guidance for demonstrating compliance to show verification.
5.7.2 Non-Transport Category Airplanes. Sections 23.2500 and 23.2505 define the regulatory safety requirement, and AC 23- 1309-1E provides guidance for demonstrating compliance. Severity of failure conditions and software development assurance levels are found in AC 23.1309-1E.
5.7.3 Rotorcraft. Sections 27.1309 and 29.1309 define the safety requirements. Regulatory guidance can be found in AC 27-1B CHG 1-9 and AC 29-2C CHG 9.Once the safety assessment has been completed, for any hazard or failure classification greater than Major, an FTA
5.7.8 EFVS system safety design criteria analysis (as applicable). › 5.7.8.1 The overall level of safety of the aircraft is based on…
should be evaluated using the guidance found in the FAA system safety AC that is applicable to the installation. The FTA should include the display monitor, power supply, imaging camera and sensors, cable, status annunciations, and other components that affect the top-level events.
5.7.4 The SSA should consider the sample operating phases in Table 2-1.
Table 2-1. System Operating Phases for Considerations
GROUND TAKEOFF IN-FLIGHT LANDING
(1) Taxi (2) Maintenance
(1) Takeoff Roll Prior to V1 (2) Takeoff Roll After V1 (3) Takeoff After VR to 200’ (4) Rejected Takeoff
(1) Climb (2) Gear Up (3) Cruise (4) Descent (5) Gear Down (6) Approach 200’ to 0’ (7) Go Around
(1) Touchdown &
Rollout (2) Taxi
5.7.5 The normal operation (without malfunction) of the EVS/EFVS/CVS should not adversely affect or be adversely affected by other normally operating aircraft functions. As applicable, similar criteria are found in SAE ARP 4754 and ARP 4761A.
5.7.6 Demonstration. Under §§ 23.2600, 25.771(a), 27.771(a), 29.771(a) and 25.1302(b), to meet the safety criteria, the EFVS design must be demonstrated to mitigate any failure combinations that can cause hazardously misleading information to be presented to the flightcrew, or which can otherwise subsequently cause an unsafe condition. Failures which are selfevident or made obvious to the flightcrew, and with which they can safely cope, need not be specifically monitored.
5.7.7 State Data. The aircraft state data are provided by the standard inertial, air data, and radio guidance sensors. Under §§ 23.1309, 25.1309, 27.1309 and 29.1309, the HUD or display processor will be required to be at a sufficient level of safety for the aircraft type and application to detect critical random or common faults that could otherwise cause an unsafe condition. The ability to continue the approach below the standard Category I DA/DH or MDA into the visual segment therefore is strictly borne by the pilot, a safety factor already accounted for in the safety analysis for standard Category I operations.
5.7.8 EFVS system safety design criteria analysis (as applicable). To demonstrate compliance with §§ 23.2500, 23.2505, 25.1309, 27.1309, 29.1309:
5.7.8.1 The overall level of safety of the aircraft is based on installed equipment. A complete SSA should be conducted to identify failure modes and classify the hazard levels. To meet the safety criteria, the system design
5.7.9 EFVS approach system required level of safety analysis (as applicable). › 5.7.9.1 Safety design goals for airworthiness approval should be…
should preclude failures that can cause hazardously misleading information (HMI) to be presented to the pilot or the flightcrew, or which can otherwise subsequently cause an unsafe condition. For example, HMI could include information providing attitude, altitude, and distance cues as outside terrain imagery.
5.7.8.2 The EFVS system must perform its intended function for each applicable operation and phase of flight in which it would be used.
5.7.8.3 The normal operation of the EFVS must not adversely affect or be adversely affected by other aircraft systems. The EFVS should annunciate detected malfunctions of the system and remove the malfunctioning display elements.
5.7.8.4 RTCA DO-315A, appendix C, lists sample categories of systems and failure probabilities to meet the safety criteria in transport category airplanes. The applicant should consider these samples when adapting to their specific design and the intended aircraft type (i.e., part 23, 25, 27 or 29 aircraft). The following additional guidance helps assess the criticality of the EFVS display, including the potential to display HMI:
• AC 25-11B (chapter 4);
• AC 23.1311-1C; and
• AC 27-1B CHG 1-9 and AC 29-2C CHG 9, as appropriate for the installation.
5.7.8.5 The applicant should validate all alleviating flightcrew actions and any cues that provide crew awareness (e.g.: alerts, status) that are considered in the EFVS safety analysis during testing either for incorporation in the AFM/airplane flight manual supplement or rotorcraft flight manual/rotorcraft flight manual supplement (RFM/RFMS) limitation section or procedures section, or for inclusion in type-specific training.
5.7.9 EFVS approach system required level of safety analysis (as applicable). To demonstrate compliance with §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309 should take the following items into consideration:
5.7.9.1 Safety design goals for airworthiness approval should be established when designing an EFVS approach system. The safety criteria for each phase of flight, including approach and landing systems, are defined in terms of accuracy, continuity, availability, and integrity. FAA design guidance provides criteria to determine the overall required level of safety for the aircraft in any mode of flight, for any combination of failures which can cause an unsafe condition to be fully assessed and categorized. For failures where the SSA assumes a particular pilot intervention to limit the hazard effects, for example from Catastrophic or Hazardous to Major or Minor,
5.7 EVS/EFVS/CVS Required Safety Level. › 5.7.10 EFVS landing system required level of safety analysis (as applicable).
the applicant should show the pilot can perform that intervention. For example, a pilot might be assumed to detect a system error because of other displays or what is being viewed out the window. It should be demonstrated that pilots can detect the error in a timely fashion and not be hazardously misled. The demonstration must validate the proposed hazard classification, as applicable.
5.7.9.2 The applicant should demonstrate a satisfactory safety (failure and performance) level which should not be less than the safety level required for non-EFVS approach system based precision and non-precision approaches with decision altitudes of 200 ft. or above. In showing compliance, probabilities cannot be factored by the fraction of approaches which are made using EFVS. Consideration, however, can be given to the EFVS approach system critical flight time, such as from the highest DA/DH that can be expected for an EFVS approach system based approach to 100 ft. above the TDZE.
5.7.9.3 The design assurance levels (DALs) are directly linked to the specific intended use and to the specific EFVS approach system installation as an integrated part of the flightdeck flight information system.
5.7.9.4 There are failure modes within the EFVS approach system which determine that software and hardware DALs should use the criteria of the latest versions of RTCA DO-178 (for software) and DO-254 (for hardware) level C as a minimum. Depending upon specific functions or system architecture, a higher DAL (for example see RTCA DO-315A, appendix C) may result from the DAL allocation analysis.
5.7.9.5 The safety assessment process, starting with the FHA, should determine whether the minimum required DAL C is adequate for your specific installation. The example FHA shown in RTCA DO 315A, appendix C is a model case only and cannot be applied to any specific aircraft without independent analysis.
5.7.9.6 The applicant must provide the applicable analysis that is specific for each installation approval. An example SSA of an EFVS approach system is shown in RTCA DO-315A, appendix C.
5.7.9.7 The applicant must conduct a safety analysis to show the EFVS approach system meets all the integrity criteria for the aircraft, HUD, and EFVS. The applicant should demonstrate system and subsystem malfunctions, which are not extremely improbable, as appropriate in a simulation or in flight. The malfunction annunciation and fault detection schemes must achieve the determined level of safety.
5.7.10 EFVS landing system required level of safety analysis (as applicable). To demonstrate compliance with §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309:
5.7.10 EFVS landing system required level of safety analysis (as applicable). › 5.7.10.5 In showing compliance with these safety criteria, the…
5.7.10.1 The applicant should demonstrate a satisfactory level of safety (failure and performance) appropriate to the operations being addressed, but with the visual segment primarily accomplished by the use of an EFVS landing system rather than natural vision.
5.7.10.2 To achieve the required safety level, the minimum baseline safety levels required for the installed EFVS landing system equipment regardless of visibility, should be dependent on the demonstrated performance.
5.7.10.3 An aircraft level FHA and SSA should be prepared by the applicant to assess the hazard level associated with system failure conditions and to determine the minimum required software and hardware DALs based on the applicant’s specific installation. Mitigating system design features include redundancy, independent guidance display, system monitoring, pilot in the loop, pilot not flying, etc. In no case should the DAL be less than DAL B.
5.7.10.4 The minimum required safety level for an EFVS landing system (EFVS to touchdown and roll out in visibilities not less than runway visual range (RVR) 1000 feet) is based on the assumption that the EFVS being approved can demonstrate that the flightcrew can verify that the aircraft is safely approaching the runway for EFVS landing system based landing, or if not, to initiate a timely go-around if sufficient enhanced visibility is not achieved. This provides additional integrity to the operation. Depending on the applicant’s design, it may be possible that the proposed natural visibility can also compensate for loss of EFVS imagery, such that the pilot can use the remaining symbolic flight information on the HUD and the external view to safely land. System evaluation should consider EFVS landing system failure modes and whether the pilot can safely land and rollout with available natural vision plus whatever capability remains of the EFVS landing system. A safe landing should not be assumed with only available natural vision after total loss of the EFVS landing system (i.e., symbology and image).
5.7.10.5 In showing compliance with these safety criteria, the applicant should not factor probabilities of EFVS landing system failure conditions by the fraction of approaches which require use of the EFVS landing system. Also, the applicant should not factor probabilities of EFVS landing system failure conditions by a statistical distribution of visibility conditions. The exposure time used for EFVS landing system failure calculations should be the elapsed time from descent below the highest expected DA/DH for the EFVS landing system-based approach to completion of rollout to a safe taxi speed.
5.7 EVS/EFVS/CVS Required Safety Level. › 5.7.12 EFVS Fail Safe Features.
5.7.11 SSA analysis (as applicable). To demonstrate compliance with §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309 analysis should contain the following elements:
5.7.11.1 An aircraft-level FHA should be prepared by the applicant to assess the hazard level associated with system failure conditions and to determine that the minimum required software and hardware DALs are appropriate to the applicant’s specific intended function.
5.7.11.2 The DALs are directly linked to the specific intended use and to the specific EFVS installation as an integrated part of the flightdeck flight information system. The availability and integrity of situational and flight path information from sources other than the EFVS image and the ability of the pilot monitoring the operation should be considered when assessing the appropriate hazard levels for the EFVS.
5.7.11.3 Under §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309, the applicant must provide an SSA.
5.7.11.4 The SSA should show that the applicant’s specific installation meets all the integrity criteria for the aircraft systems, and EFVS.
5.7.11.5 The applicant may need to demonstrate by flight test or simulation, combinations of EFVS malfunctions that are not shown to be extremely improbable (10-9) as determined by the AIR certification branch and the project specific certification plan (PSCP).
5.7.11.6 Any malfunction fault detection and annunciation schemes must satisfy the required levels of safety and must perform their intended functions.
5.7.11.7 All aircraft configurations to be approved must be addressed.
5.7.12 EFVS Fail Safe Features. Under 23.2500, 25.1353(a), 27.1351(b), and 29.1353(a), the normal operation of the EFVS must not adversely affect or be adversely affected by other normally operating aircraft systems. Warning information (e.g. annunciations) must be provided to alert the crew to unsafe EFVS operating conditions, including detected malfunctions of the EFVS which could cause display of misleading information. The misleading information should be removed. Alerting annunciations should be displayed to the flightcrew in accordance with AC 23.1311-1C, AC 25.1322-1, AC 25-11B, AC 27-1B CHG 1-9, and AC 29-2C CHG 9 as applicable. Under §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309, the applicant must assess the criticality of the EFVS’s function to display imagery, including the potential to display hazardously misleading information. That assessment should include the hazardous effects of any malfunction of the EFVS that could adversely affect interfaced equipment or associated systems. See AC 23- 1309-1E, AC 25-11B, and ARAC-recommended 25.1309 and Arsenal Guidance, AC
27-1B CHG 1-9 and AC 29-2C CHG 9. This requirement should be met through an SSA and documented via FTA, FMEA, and FMEA substantiation, or equivalent safety documentation.
CHAPTER 6. PERFORMANCE EVALUATION
6.1 EVS/EFVS Performance Demonstration. The performance demonstration used to establish aircraft system compliance with applicable FAA airworthiness criteria typically includes bench testing, simulation, flight testing, data collection, and data reduction to show that the proposed performance criteria can be met. The performance evaluations should therefore include demonstrations of the kinds of operations and those operations’ flight regimes that are stated as the system’s intended functions. For EFVS, the applicant should demonstrate performance at the lateral and vertical limits for the type of approach (for example, precision, non-precision, and approach with vertical guidance) for which operational credit is sought. Appendix B of this AC provides sample EFVS flight test considerations.
6.1 EVS/EFVS Performance Demonstration. › 6.1.3 The applicant should specify the individual verification methods…
6.1.1 This AC does not prescribe specific test procedures. We recognize that alternative methods can be used. In accordance with §§ 21.17 and 21.97, your test procedures and compliance reports must show compliance with the applicable airworthiness criteria. System performance tests are the most important tests, as they relate to operational capability. Subsystem tests are used to test subsystems during system buildup to ensure appropriate subsystem performance as it relates to overall system performance.
6.1.2 The applicant should use some or all these four general verification methods as necessary (Refer to AC 23.1309-1E, AC 25.1329-1C, AC 27-1B or AC 29-2C CHG 9 as applicable).
6.1.2.1 Analysis. Demonstrate compliance using an engineering analysis.
6.1.2.2 Flight Test. Demonstrate compliance using an aircraft that is fully representative for the purpose of the test in terms of flightdeck geometry, instrumentation, alerts, indications, and controls in the air and on the ground.
6.1.2.3 Laboratory Test. Demonstrate compliance using an engineering bench representative of the final EVS/CVS/EFVS system being approved.
6.1.2.4 Simulation. Demonstrate compliance using a flight simulator as accepted by the AIR certification branch in the PSCP.
6.1.3 The applicant should specify the individual verification methods used in the certification plan. Confirm that the responsible AIR certification branch agrees with your plan before you begin. For extensions, features, and design decisions not explicitly specified in this AC, you should conduct human factors evaluations. Conduct these
Chapter 6. Performance Evaluation › 6.2 Performance Demonstration of EFVS Landing System.
evaluations through appropriate combinations of analyses, bench testing, simulation, or flight testing.
6.1.4 The applicant should verify both the installed system and the individual system components meet the EVS/CVS/EFVS criteria described in Chapter 4 of this AC.
6.1.5 The applicant should demonstrate the system meets performance criteria specified in Chapter 4 by flight test and/or other appropriate means, which can include the use of a flight simulator. An example of a flight test program for EFVS is described in appendix C in this AC. The flight test program assumes that the guidance system utilized to satisfactorily position the aircraft at the DA/DH or MDA has been separately tested and shown to fully perform its intended function. Testing and data collection to demonstrate this is not addressed in this AC.
6.1.6 The applicant should conduct an evaluation of the system used during anticipated operational scenarios, including:
6.1.6.1 EFVS Flight Testing. Unapproved EFVS systems may be operated on test flights provided that the operation is conducted under § 91.176(d) and the aircraft is issued an experimental certificate under § 21.191.
6.1.6.2 Section 21.191, Experimental Certificates. Identifies a number of purposes for which an experimental certificate can be issued. Not all of those are eligible for the exception in § 91.176(d). Section 91.176(d) limits the exception purposes to only those listed in §§ 21.191(a) and 21.191(b). Please note, however, that using an unapproved EFVS to conduct an EFVS operation outside this specific scope would still require a waiver from the applicable operating rules.
For the Administrator to determine that the flight test operations can be conducted safely in accordance with § 91.176(d) and all other applicable regulations, the FAA will evaluate the flight test in accordance with FAA Order 8130.2J, Airworthiness Certification of Aircraft. FAA Order 8130.2J contains detailed instructions about how to obtain an experimental certificate (Chapter 4, Sec. 2 and Chapter 10.) It also describes what the applicant’s program letter must contain (appendix C) and lists what operating limitations must be applied to the experimental certificate (appendix D). As a part of the airworthiness certification process, the FAA determines whether the operations proposed by the applicant can be safely conducted. The FAA issues operating limitations when the program letter is approved, and the experimental certificate is issued.
6.2 Performance Demonstration of EFVS Landing System. Where appropriate for the performance demonstration, the non-visual conditions can be achieved either by natural obscuration or by the use of a visibility-limiting device in
6.2.5 Without requiring exceptional pilot skill, alerting, strength, or… › 6.2.5.5 Prompt and predictable correction of any lateral deviation away…
front of the pilot. Caution should be used if the applicant chooses to use a visibilitylimiting device for system performance demonstrations. Visibility-limiting devices may not adequately simulate low visibility conditions for all EFVS landing system landing performance demonstrations because of the unrealistically good external visibility outside the HUD FOV and the unrealistic EFVS landing system image performance in good atmospheric conditions.
6.2.1 Under §§ 23.2610, 25.1523, 27.1523, and 29.1523, the applicant must consider the workload associated with the use of EFVS landing system for approach, landing and rollout.
6.2.2 The system may fly final approach courses with offsets greater than 3 degrees. In this case, the applicant should establish the maximum allowable final approach course offset by flight test. The flight test should address factors related to the offset, such as HUD/EFVS FOV, crosswinds, and the maximum drift angle for a conformal FPV.
6.2.3 The EFVS landing system image with superimposed flight symbology must not mislead, distract or jeopardize the safety of the landing and rollout. Performance should be demonstrated to be no worse than that normally achieved in visual operations for the specific aircraft for all performance parameters measured. See §§ 23.2600, 25.771, 27.771, 29.771 and §§ 23.2500, 23.2505, 25.1309, 27.1309, and 29.1309. The applicant may propose a valid means for establishing performance normally achieved that the FAA may accept as a benchmark for the EFVS demonstrations.
6.2.4 Benchmark data establishing equivalence to normal visual operations with the specific aircraft is not normally necessary. However, if flight test results show deviations for the standard criteria listed above, then benchmark data might be necessary to establish the equivalence of EFVS landing system operations to normal visual operations for that specific aircraft.
Continue reading ↓ 120 of 192 passages shown