AC 194-2 Pilot Training and Certification for Powered-Lift Operations
This AC provides guidance for applicants, pilots, evaluators, and instructors who seek to add an initial powered-lift category rating and specific type rating to their existing United States (U.S.) pilot certificate in accordance with Special Federal Aviation Regulation (SFAR) 120, Powered-Lift: Pilot Certification and Training; Operations Requirements. Pilots and certificate holders (CH) are encouraged to use this information as best practice methods for developing training programs scaled to specific powered-lift they operate. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Pilot Training and Certification for
Powered-Lift Operations
Date: 11/21/24 AC No: 194-2 Initiated by: AFS-800 Change:
This advisory circular (AC) provides guidance to assist persons seeking to add an initial powered-lift category rating and specific type rating to their existing Federal Aviation Administration (FAA) pilot certificate in accordance with Special Federal Aviation Regulation (SFAR) 120, Powered-Lift: Pilot Certification and Training; Operations Requirements. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies.
Robert M. Ruiz for Lawrence Fields Executive Director, Flight Standards Service
ii
CONTENTS Paragraph Page
Chapter 1. Introduction … 1-1
1.1 Purpose of This Advisory Circular (AC) … 1-1
1.2 Audience … 1-1
1.3 Where You Can Find This AC … 1-1
1.4 Effective Date … 1-1
1.5 Related 14 CFR Parts … 1-1
1.6 Related Airman Certification Standards (ACS) (current editions) … 1-1
1.7 Definitions … 1-2
1.8 Background … 1-3
1.9 AC Feedback Form … 1-4
Chapter 2. Powered-Lift Pilot Certification—General Provisions … 2-1
2.1 General … 2-1
2.2 Type Rating Requirements … 2-1
2.3 Applicability of the Type Rating Requirement to Military Pilots … 2-1
Chapter 3. Alternate Cross-Country Requirements … 3-1
3.1 Alternate Means to Log Cross-Country Time in Powered-Lift … 3-1
3.2 Commercial Applicants … 3-1
3.3 Instrument Applicants … 3-2
3.4 Private Pilot Applicants … 3-2
Chapter 4. Alternate Requirements for Practical Tests and Training in a Powered-Lift … 4-1
4.1 Required Equipment for Practical Tests in a Powered-Lift … 4-1
4.2 Required Flight Training Tasks … 4-2
Chapter 5. Alternate Eligibility Requirements for a Person Seeking an Initial
Powered-Lift Type Rating … 5-1
5.1 Practical Tests for Powered-Lift Category Rating and Type Rating … 5-1
5.2 Eligible Applicants … 5-1
5.3 Practical Tests Required for Persons Seeking an Initial Powered-Lift Type Rating … 5-1
5.4 Pilot Privileges With a “VFR Only” Limitation … 5-2
5.5 Removal of “VFR Only” Limitation—Private Pilot … 5-2
iii
5.6 Removal of “VFR Only” Limitation—Other Than Private Pilot … 5-2
5.7 Practical Test Requirements to Remove the “VFR Only” Limitation … 5-2
5.8 Effect of Failure to Remove “VFR Only” Limitation … 5-3
5.9 Obtaining Additional Powered-Lift Type Ratings With “VFR Only” Limitation … 5-4
Chapter 6. Alternate Aeronautical Experience and Logging Requirements—
General Provisions … 6-1
6.1 Alternate Means to Obtain Ratings … 6-1
Chapter 7. Alternate Aeronautical and Logging Experience Requirements for a
Commercial Pilot Certificate With a Powered-Lift Category Rating … 7-1
7.1 Alternate Provisions for Test Pilots, FAA Test Pilots, Aviation Safety Inspectors (ASI), and Instructor Pilots … 7-1
7.2 Alternate Provisions for Initial Cadre of Instructors … 7-7
7.3 Alternate Provisions for Pilots Trained in an Approved Training Program at the CH … 7-14
Chapter 8. Alternate Aeronautical Experience and Logging Requirements for an
Instrument-Powered-Lift Rating … 8-1
8.1 Alternate Provisions for Test Pilots, FAA Test Pilots, Aviation Safety Inspectors (ASI), and Instructor Pilots … 8-1
8.2 Alternate Provisions for Initial Cadre of Instructors … 8-5
8.3 Alternate Provisions for Pilots Trained in an Approved Training Program at the CH … 8-10
Chapter 9. Alternate Requirements for Powered-Lift Without Fully Functioning Dual
Controls Used in Flight Training … 9-1
9.1 Alternate Requirements for Flight Training Using an Aircraft Without Fully Functioning Dual Controls … 9-1
9.2 Required Training … 9-1
9.3 Practical Test … 9-4
9.4 Supervised Operating Experience (SOE) for a Powered-Lift With Single Controls and a Single Pilot Station … 9-5
Chapter 10. Miscellaneous Qualification Requirements … 10-1
10.1 Requirements for Pilots Serving as Second in Command (SIC) in a Powered-Lift … 10-1
10.2 Training in a Powered-Lift that Requires Two Pilot Flight Crewmembers … 10-2
10.3 Second in Command Professional Development Program (SIC PDP) … 10-2
iv
10.4 Supervised Operating Experience (SOE) Requirements of § 61.64 … 10-3
Chapter 11. Part 91K Requirements to Serve as a Powered-Lift Pilot in a
Fractional Ownership Program … 11-1
11.1 Use of Powered-Lift in Part 91K … 11-1
11.2 Part 91K Crewmember Experience Requirements … 11-1
11.3 Pilot Operating Limitations and Pairing Requirement … 11-1
Chapter 12. Requirements to Serve as a Powered-Lift Pilot Under Part 135 … 12-1
12.1 Alternate Provisions for Persons Receiving Training Under a Part 135 Approved Training Program … 12-1
12.2 Certification Training Curricula … 12-3
12.3 Advanced Qualification Program (AQP) … 12-3
12.4 PIC Qualifications … 12-4
12.5 Applicability of Rules for Eligible On-Demand Operations … 12-4
Chapter 13. Requirements for Part 141 Sschools … 13-1
13.1 Class Rating Requirements for Part 141 … 13-1
13.2 Alternate Qualification Requirements for Chief Instructors, Assistant Chief Instructors, and Check Instructors … 13-1
13.3 Alternate Qualification Requirements for Check Instructors for Checks and Tests That Relate to Ground Training … 13-1
13.4 Alternate Means to Satisfy Flight Training Minimum Curriculum Content Specified in Part 141 Appendices for a Powered-Lift Category Rating … 13-1
13.5 Alternate Cross-Country Requirements Applicable to Part 141 Approved Courses … 13-2
Chapter 14. Part 91 Pilot Certification for Powered-Lift With Special
Airworthiness Certificates for Experimental Purposes … 14-1
14.1 Operating Limitations … 14-1
Appendix A. Example Endorsements … A-1
Appendix B. List of Advisory Circulars Affected by 14 CFR Part 194 … B-1
v
List of Tables
Table 7-1. Alternate Provisions for a Commercial Pilot Certificate With a Powered-Lift Category Rating: Test Pilots and Instructor Pilots … 7-4
Table 7-2. Alternate Provisions for a Commercial Pilot Certificate With a Powered-Lift Category Rating: Initial Cadre of Check Pilots, Chief Instructors, Assistant Chief Instructors, and Training Center Evaluators (Initial Cadre Instructors) … 7-11
Table 7-3. Alternate Provisions for a Commercial Pilot Certificate With a Powered-Lift Category Rating: Persons Receiving Training Under a Part 135, 141, or 142 Approved Training Program … 7-16
Table 8-1. Alternate Provisions for an Instrument-Powered-Lift Rating: Test Pilots and Instructor Pilots … 8-3
Table 8-2. Alternate Provisions for an Instrument-Powered-Lift Rating: Initial Cadre of Check Pilots, Chief Instructors, Assistant Chief Instructors, and Training Center Evaluators (Initial Cadre Instructors) … 8-8
Table 8-3. Alternate Provisions for an Instrument-Powered-Lift Rating: Persons Receiving Training Under a Part 135, 141, or 142 Approved Training Program … 8-11
Table 12-1. Powered-Lift Pilot-in-Command Qualifications … 12-4
CHAPTER 1. INTRODUCTION › 1.6 Related Airman Certification Standards (ACS) (current editions).
CHAPTER 1. INTRODUCTION
1.1 Purpose of This Advisory Circular (AC). This AC provides guidance for applicants, pilots, evaluators, and instructors who seek to add an initial powered-lift category rating and specific type rating to their existing United States (U.S.) pilot certificate in accordance with Special Federal Aviation Regulation (SFAR) 120, Powered-Lift: Pilot Certification and Training; Operations Requirements. Pilots and certificate holders (CH) are encouraged to use this information as best practice methods for developing training programs scaled to specific powered-lift they operate. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way, and the document is intended only to provide information to the public regarding existing requirements under the law or agency policies.
1.2 Audience. The primary audience for this AC is persons seeking to obtain an initial powered-lift category rating, a specific type rating, and/or an instrument-powered-lift rating to an existing pilot or flight instructor certificate (e.g., applicants, pilots, and flight instructors) and entities seeking to provide training to such persons (e.g., Title 14 of the Code of Federal Regulations (14 CFR) part 135 operators, part 141 pilot schools, and part 142 training centers). Designated Pilot Examiners (DPE), aviation safety inspectors (ASI), and other persons who conduct certification functions for pilots should familiarize themselves with this AC as well.
1.3 Where You Can Find This AC. You can find this AC on the Federal Aviation Administration’s (FAA) website at https://www.faa.gov/regulations_policies/advisory_cir culars and the Dynamic Regulatory System (DRS) at https://drs.faa.gov.
1.4 Effective Date. This AC is effective as of November 21, 2024.
1.5 Related 14 CFR Parts. The following are available at https://www.ecfr.gov:
• Part 61, Certification: Pilots, Flight Instructors, and Ground Instructors.
• Part 91 Subpart D, Special Flight Operations.
• Part 91 Subpart K (Part 91K), Fractional Ownership Operations.
• Part 135, Operating Requirements: Commuter and On Demand Operations and Rules Governing Persons On Board Such Aircraft.
• Part 141, Pilot Schools.
• Part 142, Training Centers.
1.6 Related Airman Certification Standards (ACS) (current editions). The following should be read in conjunction with this AC and are available at https://www.faa.gov/traini ng_testing/testing/acs:
1.7 Definitions. › 1.7.4 FAA Test Pilot (§ 194.103). A pilot employed by the FAA to…
• FAA-S-ACS-2, Commercial Pilot for Powered-Lift Category Airman Certification Standards.
• FAA-S-ACS-3, Instrument Rating—Powered-Lift Airman Certification Standards.
• FAA-S-ACS-13, Private Pilot for Powered-Lift Category Airman Certification Standards.
• FAA-S-ACS-17, Airline Transport Pilot and Type Rating for Powered-Lift Category Airman Certification Standards.
• FAA-S-ACS-27, Flight Instructor for Powered-Lift Category Airman Certification Standards.
• FAA-S-ACS-28, Flight Instructor—Instrument Rating Powered-Lift Airman Certification Standards.
1.7 Definitions. The following definitions are only for the purposes of this AC and 14 CFR Part 194, Special Federal Aviation Regulation No. 120—Powered-Lift: Pilot Certification and Training; Operations Requirements.
1.7.1 Alternate Definition of Cross-Country Time (part 194, § 194.201). Notwithstanding the cross-country time definition in part 61, § 61.1(b), a person may log flight time in a powered-lift as cross-country time provided the time was acquired during a flight:
1. That includes a point of landing that was at least a straight-line distance of more than 25 nautical miles (NM) from the original point of departure; and
2. That involves the use of dead reckoning (DR), pilotage, electronic navigation aids, radio aids, or other navigation systems to navigate to the landing point.
1.7.2 Aviation Safety Inspector (ASI) (§ 194.103). A pilot employed by the FAA to conduct operations of a powered-lift for the purpose of establishing a type rating in that specific powered-lift under 14 CFR part 21, as appropriate.
1.7.3 Evaluator. For the purposes of this AC, an evaluator is considered:
• An ASI;
• A pilot examiner (other than administrative pilot examiners);
• An initial check pilot;
• A Training Center Evaluator (TCE);
• An Aircrew Program Designee (APD); or
• A chief instructor, an assistant chief instructor, or a check instructor of an approved part 141 pilot school or provisional school.
1.7.4 FAA Test Pilot (§ 194.103). A pilot employed by the FAA to conduct operations of a powered-lift for the purpose of FAA examination or inspection of a type design for which an application for type certification has been submitted under part 21.
1.7.5 Instructor Pilot (§ 194.103). A pilot employed or used by a manufacturer of a powered-lift to conduct operations of the powered-lift for the purpose of developing a proposed training curriculum and providing crew training. This term is not the same as an authorized instructor.
1.8 Background. › 1.8.3 When powered-lift are introduced to civil aviation, pilots will…
1.7.6 Manufacturer (§ 194.103). Any person who holds, or is an applicant for, a type or production certificate for an aircraft. An amateur builder under part 21, § 21.191(g), a builder of a kit aircraft under § 21.191(h), or the holder of a restricted category type certificate (TC) is not considered a manufacturer for the purposes of part 21.
1.7.7 Test Pilot (§ 194.103). A pilot employed or used by a manufacturer of a powered-lift to conduct operations of the powered-lift for the purpose of research and development (R&D) and showing compliance with the regulations.
1.8 Background.
1.8.1 As a result of the rapidly changing technology and newly designed aircraft intending to fly in the National Airspace System (NAS), the FAA created regulations to account for the new category of aircraft. A portion of the regulatory changes include creating pilot training and certification requirements for a new aircraft category. Part 194 provides regulatory requirements for powered-lift pilot certification and operations. Prior to this regulation, the FAA did not have a feasible means to implement training and certification of pilots for a powered-lift category rating due to a lack of certificated aircraft and certified personnel to provide instruction. This new regulation establishes requirements for qualifying pilots in powered-lift by utilizing new and existing pathways for pilot training, checking, and testing in powered-lift under parts 61, 91, 135, 141, 142, and 194. Additionally, SFAR 120 provides for alternate pathways for training and certification of pilots, as there is currently limited means to obtain experience in a powered-lift.
1.8.2 Currently, civilian pilots are unable to satisfy many of the aeronautical experience requirements in part 61 to obtain a Commercial Pilot Certificate with a powered-lift category rating and/or an instrument-powered-lift rating because there are no certificated powered-lift in civil operations in which they can obtain the necessary flight time. At the time of publication of this Final Rule, the only certificates with powered-lift category ratings were those issued to military pilots that attained their certificates through military competency under § 61.73. Additionally, there are currently no type-certificated civilian powered-lift; however, there are many manufacturers starting the production process.
1.8.3 When powered-lift are introduced to civil aviation, pilots will initially be unable to satisfy several of the aeronautical experience requirements for a Commercial Pilot Certificate with a powered-lift category rating and an instrument-powered-lift rating (such as pilot-in-command (PIC) flight time in powered-lift and cross-country experience in powered-lift) due to lack of qualified civilian pilots and instructors in powered-lift. Further, the PIC logging requirements of § 61.51(e) currently present obstacles for a pilot who is not rated in a powered-lift to log PIC flight time in a powered-lift. Additionally, in light of the range limitations of current type-certification projects for powered-lift, and several planned projects, many powered-lift coming to market are not capable of
CHAPTER 1. INTRODUCTION › 1.9 AC Feedback Form.
completing the prescribed cross-country aeronautical experience requirements for the Commercial Pilot Certificate and instrument rating. SFAR 120 facilitates pathways for pilots to obtain powered-lift ratings through alternate aeronautical experience and expanded logging provisions.
1.9 AC Feedback Form. For your convenience, the AC Feedback Form is the last page of this AC. Note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this AC on the Feedback Form.
2.3 Applicability of the Type Rating Requirement to Military Pilots. › 2.3.2 However, to act as PIC of a civilian powered-lift, these military…
CHAPTER 2. POWERED-LIFT PILOT CERTIFICATION—GENERAL PROVISIONS
2.1 General. Title 14 CFR part 194 maintains the regulatory framework of powered-lift as an independent aircraft category without any associated classes. The FAA expects that, initially, most pilots seeking to add a powered-lift category rating to their pilot certificate will already hold another category rating (i.e., airplane or rotorcraft) on their certificate. In fact, as subsequently discussed, to utilize most of the alternate aeronautical experience requirements and logging provisions, pilots are required by part 194, § 194.215 to hold certain certificates and ratings. Permanent changes to 14 CFR part 61, as well as temporary alternate experience requirements in SFAR 120, work in tandem to provide methods for certification for all powered-lift pilots. The next several chapters outline the temporary and permanent changes that affect pilot training, checking, and testing in powered-lift.
2.2 Type Rating Requirements. To address the expected significant operational differences between each powered-lift, part 61, § 61.31(a) requires each person who acts as pilot in command (PIC) of a powered-lift to hold the associated type rating. Requiring pilots to hold type ratings for powered-lift establishes a higher level of safety by ensuring persons receive adequate training and are tested on the unique design and operating characteristics of each powered-lift. The Flight Standardization Board (FSB) will identify the unique characteristics of each powered-lift that require special training. Subsequently, the report should be utilized in conjunction with the appropriate powered-lift Airman Certification Standards (ACS) to conduct training and practical tests for a type rating, ensuring that an applicant is knowledgeable and capable of safely operating the unique powered-lift type.
2.3 Applicability of the Type Rating Requirement to Military Pilots.
2.3.1 Military pilots may continue to apply for Commercial Pilot Certificates with powered-lift category ratings and instrument-powered-lift ratings, and flight instructor certificates with powered-lift category ratings and instrument-powered-lift ratings, pursuant to the existing requirements in § 61.73, based on their military pilot qualifications.
2.3.2 However, to act as PIC of a civilian powered-lift, these military pilots are required to obtain a type rating on their pilot certificate for the applicable type of civilian powered-lift, as required by § 61.31(a). As required by § 61.195(e), those military instructors who have obtained or plan to obtain a flight instructor certificate with a powered-lift category rating and instrument-powered-lift rating through military competency may conduct flight training in a powered-lift only after obtaining a type rating on their pilot certificate for the powered-lift in which they want to conduct flight training.
3.2 Commercial Applicants. › 3.2.1 Under part 61, § 61.129(e)(3), applicants for a powered-lift…
CHAPTER 3. ALTERNATE CROSS-COUNTRY REQUIREMENTS
3.1 Alternate Means to Log Cross-Country Time in Powered-Lift.
3.1.1 Due to the expected disparity between powered-lift range capabilities, 14 CFR part 194 includes an alternate definition of cross-country time that reduces the general distance to log cross-country time in a powered-lift from more than 50 nautical miles (NM) to more than 25 NM. Specifically, to log flight time in a powered-lift as cross-country time, part 194, § 194.201 requires a point of landing that is at least a straight-line distance of more than 25 NM from the original point of departure and involves the use of dead reckoning (DR), pilotage, electronic navigation aids, radio aids, or other navigation systems to navigate to the landing point.
3.1.2 For applicants not qualified to act as pilot in command (PIC) in a powered-lift, § 194.213 requires all persons conducting cross-country flights to receive an endorsement from an authorized instructor or instructor pilot. Since applicants are not qualified to be PIC in a powered-lift, they will need an endorsement from the authorized instructor or instructor pilot stating that the applicant meets the alternate cross-country requirements. The applicant’s logbook must demonstrate to the evaluator that they have met the alternate cross-country requirements of part 194 in lieu of the standard 14 CFR part 61 regulatory requirements. Appendix A provides an example of each endorsement.
3.1.3 In addition to the cross-country definition, part 194 provides relief from specific cross-country requirements, dependent on the certificate sought, to address possible range capabilities, as previously discussed. Paragraphs 3.2 through 3.4 detail specific relief options for applicants.
3.1.4 To note, a pilot may satisfy either the traditional part 61 cross-country pathway or the alternate cross-country requirements set forth by part 194, as applicable, to meet the requisite cross-country aeronautical experience.
3.2 Commercial Applicants.
3.2.1 Under part 61, § 61.129(e)(3), applicants for a powered-lift rating are required to complete only two cross-country flights, one in daytime conditions and one in nighttime conditions, each including a total straight-line distance of more than 100 NM from the original point of departure. However, as many powered-lift are expected to be unable to comply with existing cross-country requirements, the alternate requirements in part 194 reduce the distance required for the cross-country flight to a total straight-line distance of more than 50 NM and add an additional cross-country flight with landings at a minimum of three points as a safety mitigation. Section 194.233(a)(3) requires that, other than the original point of departure, the third cross-country flight must be performed to different points than the first two cross-country flights at the distances specified. The third cross-country flight may be conducted during day or nighttime conditions. This additional cross-country flight will add to the applicant’s overall experience in the specific powered-lift in which the applicant is seeking their initial Commercial Pilot Certificate with powered-lift category rating.
3.4 Private Pilot Applicants. › 3.4.1 Section 194.201 authorizes private pilot applicants to apply the…
3.2.2 In lieu of complying with § 61.129(e)(3), § 194.233 allows an applicant seeking a Commercial Pilot Certificate in a powered-lift to complete the following cross-country flights:
1. One 2-hour cross-country flight in a powered-lift in daytime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure;
2. One 2-hour cross-country flight in a powered-lift in nighttime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure; and
3. An additional cross-country flight with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. This flight must include landings at different points than the points selected for the previous two cross-country flights.
3.3 Instrument Applicants. Section 61.65(f)(2)(ii) requires completion of one cross-country flight of 250 NM. In lieu of complying with this requirement, § 194.235 allows an applicant seeking an instrument rating in a powered-lift to complete two cross-country flights, each of which must involve a flight of 100 NM along airways or by directed routing from an air traffic control (ATC) facility. The other requirements in § 61.65(f)(2)(ii) still apply. Thus, each cross-country flight with the reduced 100 NM distance must be performed under instrument flight rules (IFR) when a flight plan has been filed with an ATC facility and must involve an instrument approach at each airport and three different kinds of approaches with the use of navigation systems. However, an applicant utilizing the alternate means under § 194.235 is not required to file a flight plan and perform the cross-country flight under IFR if the powered-lift is not certificated for instrument flight and the applicant holds either:
• An instrument-airplane rating,
• An instrument-helicopter rating, or
• An Airline Transport Pilot (ATP) Certificate with an airplane category rating or rotorcraft category and helicopter class ratings.
3.3.1 In lieu of complying with § 61.65(f)(2)(ii), § 194.235 allows an applicant seeking an instrument-powered-lift rating to complete the following cross-country flights two cross-country flights conducted with either an authorized instructor or an instructor pilot that involve a flight of 100 NM along airways or by directed routing from an ATC facility, include an instrument approach at each airport, and include three different kinds of approaches with the use of navigation systems.
3.4 Private Pilot Applicants.
3.4.1 Section 194.201 authorizes private pilot applicants to apply the alternate definition of cross-country time when seeking to comply with the cross-country flight training in § 61.109(e)(1). In addition, instead of completing one cross-country flight of over
3.4 Private Pilot Applicants. › 3.4.2 Additionally, in place of the solo cross-country flight that is…
100 NM distance at night, as currently required by § 61.109(e)(2)(i), § 194.237(a) allows an applicant to complete two cross-country flights at night, each of which involves a flight of over 50 NM total distance.
3.4.2 Additionally, in place of the solo cross-country flight that is currently required by § 61.109(e)(5)(ii) (i.e., 150 NM total distance with one segment of the flight consisting of a straight-line distance of more than 50 NM), § 194.237(b) allows an applicant to complete the following alternate requirements:
1. One solo cross-country flight of 100 NM total distance, with landings at three points, and one segment of the flight being a straight-line distance of more than 25 NM between the takeoff and landing locations; and
2. An additional solo cross-country flight in a powered-lift with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. This additional solo cross-country flight requires landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 25 NM from the original point of departure. This additional cross-country flight must include different points of landing than the initial cross-country flight.
4.1 Required Equipment for Practical Tests in a Powered-Lift. › 4.1.3 Section 61.43(a)(1) requires that the completion of a practical…
CHAPTER 4. ALTERNATE REQUIREMENTS FOR PRACTICAL TESTS AND
TRAINING IN A POWERED-LIFT
4.1 Required Equipment for Practical Tests in a Powered-Lift.
4.1.1 Title 14 CFR part 61, § 61.45(b) stipulates the equipment, other than controls, required of an aircraft used on the practical test and allows the use of an aircraft with operating characteristics that preclude the applicant from performing all the tasks for a practical test. In this case, an appropriate limitation is placed on the applicant’s certificate or rating. However, 14 CFR part 194, § 194.207(a) permits an applicant for a certificate or rating to use a powered-lift that is precluded from performing all of the tasks required for the practical tests. Applicants will not be required to have the certificate or rating issued with an appropriate limitation, as is currently required by § 61.45(b)(2). The purpose of the limitation under § 61.45(b)(2) is to ensure the pilot operates only the make and model (M/M) within the category and class of aircraft brought to the test, thereby preventing the pilot from acting as pilot in command (PIC) of an aircraft capable of performing tasks for which the pilot has not been tested. However, in the case of pilots seeking a certificate with associated powered-lift ratings, § 61.31(a)(3) requires all pilots to receive a PIC type rating for each aircraft type. Therefore, such a limitation is not necessary because § 61.31(a)(3) requires applicants to take a practical test in each powered-lift they seek to operate to act as PIC. In other words, because all powered-lift will require a type rating, a pilot is already limited to acting as PIC of only those powered-lift for which they hold a type rating (i.e., for which they have passed a practical test).
4.1.2 For example, if type A powered-lift could not perform a stall, then a pilot seeking a type rating in type A would not be tested on stalls and would not receive a limitation on the type rating for type A. If the pilot wished to act as PIC of type B powered-lift, which is capable of performing a stall, the absence of a limitation for the type rating for type A would not present a safety concern because the pilot would need to take a practical test for a type rating in type B powered-lift, pursuant to § 61.31(a), which would include the previously omitted evaluation on stalls. In other words, the type rating itself contains the limitation contemplated in § 61.45(b)(2) for an aircraft not able to perform all tasks in the Airman Certification Standards (ACS).
4.1.3 Section 61.43(a)(1) requires that the completion of a practical test for a certificate or rating includes the performance of the tasks specified in the areas of operation for the airman certificate or rating sought. For powered-lift, these tasks are set forth in the ACS for the appropriate certificate or rating that the applicant is seeking. Section 194.207(b) provides evaluators conducting practical tests for powered-lift the ability to waive any task for which the FAA has provided waiver authority. In order to determine what tasks may be waived, the type certification and evaluation process will be utilized to identify the operational limitations of the powered-lift, which may preclude the conduct of certain tasks listed in the ACS. The Flight Standardization Board Report (FSBR) subsequently will ascertain what tasks in the ACS are not applicable to the specific type of powered-lift. This waiver authority is not at the evaluator’s discretion; rather, the waived tasks are set forth on a designee’s Certificate Letter of Authority (CLOA) specific to each powered-lift type in which they are authorized to conduct practical tests. Specifically, the
4.2 Required Flight Training Tasks. › 4.2.1 In the case where the FAA identifies that a task is precluded…
CLOA will identify the type of powered-lift that the evaluator is authorized to conduct a practical test in, and the specific tasks that the evaluator is authorized to waive for the practical test will be set forth in the limitations section of the CLOA.
4.2 Required Flight Training Tasks. In addition to the required tasks specified in the areas of operation for the airman certificate and rating sought, § 61.39(a) requires an applicant for a certificate or rating to receive and log flight training on the applicable areas of operation. Section 194.207 authorizes an evaluator to waive a specific task during a practical test because the powered-lift used is precluded of performing a specific task. Therefore, an applicant for a Private Pilot Certificate or Commercial Pilot Certificate with a powered-lift category rating concurrently with a powered-lift type rating is relieved from the requirement to receive flight training on any task specified in an area of operation that is waived on the practical test.
4.2.1 In the case where the FAA identifies that a task is precluded from being accomplished because of factors during aircraft certification, the FAA will update its website at https://www.faa.gov in order to notify instructors, designees, and the general public on any specific task that is precluded from being trained or tested.
5.3 Practical Tests Required for Persons Seeking an Initial… › 5.3.2 The “VFR only” limitation in § 194.211(b) is a one-time-only…
CHAPTER 5. ALTERNATE ELIGIBILITY REQUIREMENTS FOR A PERSON
SEEKING AN INITIAL POWERED-LIFT TYPE RATING
5.1 Practical Tests for Powered-Lift Category Rating and Type Rating. If an applicant applies to obtain an initial powered-lift type rating concurrently with a powered-lift category rating and instrument-powered-lift rating, that applicant is required to take three practical tests concurrently under 14 CFR part 61, § 61.63(d)(1). However, SFAR 120 provides temporary relief for the initial powered-lift practical tests. Title 14 CFR part 194, § 194.211(b) provides eligible applicants with an option to obtain a powered-lift type rating without concurrently completing the required instrument rating; in other words, the applicant may take the instrument-powered-lift rating practical test independent from the practical tests for the powered-lift category and type ratings.
5.2 Eligible Applicants. To be eligible to utilize the relief provided in § 194.211(b) and obtain an initial powered-lift type rating without concurrently holding or concurrently obtaining an instrument-powered-lift rating, a person must be seeking a type rating in a powered-lift capable of performing instrument maneuvers and procedures, pursuant to § 194.211(a). If the powered-lift in which the type rating is sought is incapable of performing instrument maneuvers and procedures, then the applicant must comply with § 61.63(e).
Note: Although certain powered-lift may not be instrument flight rules (IFR)-certified initially, they will likely be capable of performing instrument maneuvers and procedures because they will have the equipment necessary to perform instrument maneuvers. In this case, the applicant would be required to comply with either § 61.63(d) or § 194.211.
5.3 Practical Tests Required for Persons Seeking an Initial Powered-Lift Type Rating.
5.3.1 Under § 194.211(b)(1), applicants for an initial powered-lift type rating to be completed concurrently with a powered-lift category rating would not need to concurrently hold or obtain the instrument-powered-lift rating at the same time they obtain their powered-lift type and category ratings. Instead, the applicant applying for an initial powered-lift type rating pursuant to § 194.211(b) could choose to take the instrument-powered-lift rating practical test independent from the powered-lift type rating practical test and powered-lift category rating practical test. Opting to take the instrument-powered-lift rating practical test separately results in a “visual flight rules (VFR) only” limitation being placed on the type rating. Paragraph 5.6 describes how to remove the limitation. Commercial applicants will also receive the limitation specified in § 61.133(b)(1), “The carriage of passengers for hire in powered-lifts on cross-country flights in excess of 50 nautical miles or at night is prohibited.”
5.3.2 The “VFR only” limitation in § 194.211(b) is a one-time-only option for initial powered-lift type rating applicants that do not wish to be subjected to the burden of taking three practical tests at one time. Except as provided in § 194.211(c), any additional powered-lift type ratings require the entire practical test in accordance with
5.7 Practical Test Requirements to Remove the “VFR Only” Limitation. › 5.7.1 In accordance with § 194.211(b)(4), a person with a powered-lift…
FAA-S-ACS-17, Airline Transport Pilot and Type Rating for Powered-Lift Category Airman Certification Standards (ACS).
5.3.3 Additionally, because § 194.211(b)(2) does not require the type rating test to be taken in actual or simulated instrument conditions, the practical test for the type rating would not require the applicant to perform those areas of operation in the ACS that include instrument maneuvers and procedures in actual or simulated instrument conditions.
5.4 Pilot Privileges With a “VFR Only” Limitation. In accordance with § 61.3(e), a pilot with a “VFR only” limitation (i.e., the pilot did not concurrently complete the instrument-powered-lift rating practical test and, therefore, does not possess the instrument rating) on their powered-lift type rating is prohibited from operating the powered-lift under IFR even if the powered-lift can perform instrument procedures and maneuvers. The pilot is only permitted to operate the powered-lift under the conditions for which the pilot demonstrated mastery of the powered-lift on the practical test.
5.5 Removal of “VFR Only” Limitation—Private Pilot. Under § 194.211(b)(6), a pilot holding a Private Pilot Certificate with a powered-lift type rating and category rating with a powered-lift “VFR only” limitation is not required to remove the “VFR only” limitation if the limitation applies to a powered-lift type that is not a large aircraft or turbojet-powered. If a private pilot chooses to remove the “VFR only” limitation, they must comply with the “VFR only” limitation removal requirements set forth by § 194.211(b)(4), as discussed in paragraph 5.6.
5.6 Removal of “VFR Only” Limitation—Other Than Private Pilot. Except for private pilots that operate powered-lift types that are not large aircraft or turbojet-powered, a person who obtains a powered-lift type rating with a “VFR only” limitation must remove the “VFR only” limitation within 2 calendar months from the month in which the person completed the powered-lift type rating practical test, in accordance with § 194.211(b)(4).
Note: The purpose of the “VFR only” limitation is to permit limited flexibility in the scheduling of the instrument-powered-lift rating practical test at a time separate from the category and type rating practical tests. An applicant is eligible to take the instrument-powered-lift rating practical test at the same time as the powered-lift type rating and powered-lift category rating practical tests. Therefore, the applicant will have obtained the required 3 hours of flight training in preparation for the instrument rating practical test within the 2 calendar months preceding the month of the practical tests, as required by § 61.65(f)(2)(i). The applicant should have sufficient time within the 2-calendar-month window for the endorsement to complete all of the practical tests and should not need to accomplish any additional training to be eligible to take the instrument-powered-lift practical test during this time period.
5.7 Practical Test Requirements to Remove the “VFR Only” Limitation.
5.7.1 In accordance with § 194.211(b)(4), a person with a powered-lift type rating with a “VFR only” limitation may remove the limitation by completing both of the following:
1. Passing an instrument rating practical test in a powered-lift, where the test must be passed in actual or simulated instrument conditions; and
5.8 Effect of Failure to Remove “VFR Only” Limitation. › 5.8.1 If the pilot does not remove the “VFR only” limitation as…
2. Passing a practical test in the powered-lift type for which the “VFR only” limitation applies on the areas of operation listed in § 61.157(e)(3) that includes performing instrument maneuvers and procedures in actual or simulated instrument conditions.
5.7.2 The required tasks for the instrument-powered-lift rating are found in FAA-S-ACS-3, Instrument Rating—Powered-Lift Airman Certification Standards. The Airline Transport Pilot (ATP) and Type Rating for Powered-Lift Category ACS specifies which areas of operation and tasks an applicant must satisfactorily perform during the type rating practical test to remove the “VFR only” limitation for a powered-lift type.
5.7.3 When an applicant takes concurrent practical tests to remove the “VFR only” limitation from their certificate, they will have to accomplish all required tasks, per § 194.211(b)(4). However, when a task required for the instrument rating practical test overlaps with a task required for the type rating practical test, § 194.211(d) allows an applicant to perform the task a single time, provided the person performs the task to the highest standard required for the task.
Example: An applicant with a “VFR only” limitation on their powered-lift type rating applies to take the instrument-powered-lift practical test to remove the limitation. That person would be required to perform a circling approach procedure on both the instrument rating practical test and the type rating practical test. The Instrument Rating—Powered-Lift ACS requires the applicant to perform the procedures while maintaining an airspeed of ±10 knots and a desired heading/track of ±10 degrees. The ATP and Type Rating for Powered-Lift Category ACS also requires the applicant to perform the circling approach procedure, but to more exacting standards (e.g., maintain an airspeed of ±5 knots and a desired heading/track of ±5 degrees). If a pilot demonstrates their ability to perform the circling approach procedure to the more exacting standards specified in the ATP and Type Rating for Powered-Lift Category ACS, the pilot would not be required to perform the same task a second time to the less stringent standards specified in the Instrument Rating—Powered-Lift ACS.
5.7.4 In addition, once a commercial applicant successfully completes the instrument practical test, the limitation specified in § 61.133(b)(1) will also be removed because, consistent with that section, the pilot will have accomplished the requirements listed in § 61.65 for an instrument rating in the same category of aircraft listed on the person’s Commercial Pilot Certificate.
5.8 Effect of Failure to Remove “VFR Only” Limitation.
5.8.1 If the pilot does not remove the “VFR only” limitation as required by § 194.211(b)(3), then the powered-lift type rating for which the “VFR only” limitation applies will become invalid for use until the person removes the limitation in accordance with § 194.206(b)(4). Per § 194.211(b)(3), a pilot who does not complete the instrument practical test and remaining ACS tasks of the type rating practical test within
CHAPTER 5. › 5.9 Obtaining Additional Powered-Lift Type Ratings With “VFR Only”…
2 calendar months from issuance of the initial powered-lift type rating will no longer be qualified to fly a powered-lift. In order to restore their powered-lift privileges, the pilot must have 3 hours of training within the previous 2 calendar months and complete the requisite practical tests.
5.8.2 If a pilot does not complete the instrument practical test in the powered-lift within 2 calendar months and that pilot is qualified in another category aircraft, they may continue to exercise their other privileges while their powered-lift privileges are invalid. For example, if a pilot holds an airplane category rating and is adding a powered-lift category rating and initial type rating but does not complete the practical test to remove the “VFR only” limitation within 2 calendar months, they can continue to exercise their airplane privileges.
5.9 Obtaining Additional Powered-Lift Type Ratings With “VFR Only” Limitation. A person holding a Private Pilot Certificate may apply for an additional powered-lift type rating with a “VFR only” limitation. Pursuant to § 194.211(c), an applicant who holds a Private Pilot Certificate and is seeking an additional powered-lift type rating for a powered-lift that is not a large aircraft or turbojet-powered need not comply with the requirements of § 61.63(d)(1). Rather, the applicant may apply without holding or concurrently obtaining an instrument-powered-lift rating, but the type rating will be limited to “VFR only.” As with obtaining an initial powered-lift type rating with a “VFR only” limitation, the applicant does not have to take the type rating practical test in actual or simulated instrument conditions and may remove the limitation for that powered-lift in the same manner specified to remove a “VFR only” limitation on an initial powered-lift type rating, as set forth in § 194.211(b)(4) (and discussed in paragraph 5.7).
6.1 Alternate Means to Obtain Ratings. › 6.1.3 In accordance with § 194.215(a), the alternate aeronautical…
CHAPTER 6. ALTERNATE AERONAUTICAL EXPERIENCE AND LOGGING
REQUIREMENTS—GENERAL PROVISIONS
6.1 Alternate Means to Obtain Ratings.
6.1.1 Pilots seeking to receive a Commercial Pilot Certificate with a powered-lift category rating in accordance with 14 CFR part 61, § 61.129(e) and an instrument-powered-lift rating in accordance with § 61.65(f) may encounter certain challenges in gaining the aeronautical experience necessary to receive these ratings. Therefore, the FAA has established alternate means for certain persons seeking to obtain ratings in a powered-lift. A person may choose to comply with the alternate aeronautical experience and logging requirements or the standard part 61 requirements. However, if no alternate aeronautical experience or logging requirement is provided in 14 CFR part 194, then the person must meet the applicable part 61 requirements, pursuant to part 194, § 194.215(b).
6.1.2 Part 194 provides a pathway for new aircraft entering the civilian market and the initial pilots who fly these aircraft. The alternate pathway is broken down into three groups with specific alternate aeronautical experience requirements set forth to qualify the person to take the practical test. The three groups include:
1. Instructor pilots and test pilots at a manufacturer. Test pilots and instructor pilots employed by a specific manufacturer for aircraft undergoing certification are authorized to log aeronautical experience in these aircraft through a Letter of Authorization (LOA). Additionally, FAA test pilots or aviation safety inspectors (ASI) will also be able to log aeronautical experience in these aircraft when conducting duties for the purpose of establishing new type designs in the case of an FAA test pilot, or for the purpose of establishing a pilot type rating in the case of an ASI.
2. Initial cadre of instructors at a certificate holder (CH) (check pilots, chief instructors, assistant chief instructors, or Training Center Evaluators (TCE)). These individuals will need to satisfactorily complete the manufacturer’s training curriculum in a type-certificated aircraft at the manufacturer to qualify for the practical test to add a powered-lift category rating.
3. Pilots receiving training under an approved training program. CHs will need to apply for and receive approval of a training curriculum so that the initial cadre of instructors who train with the manufacturer can return to the CH and train pilots on the use of the powered-lift.
Note: The FAA uses the term “initial cadre” throughout this AC. In some instances, initial cadre refers to a sufficient number of instructors and evaluators to train and qualify pilots for powered-lift ratings under an approved training program under 14 CFR part 135, 141, or 142. In other instances, the term refers to a sufficient number of pilots who are rated in powered-lift.
6.1.3 In accordance with § 194.215(a), the alternate aeronautical experience requirements (except for cross-country) for a Commercial Pilot Certificate and instrument-powered-lift
rating are only applicable to individuals who hold at least a Commercial Pilot Certificate with:
1. An airplane category rating with a single-engine or multiengine class rating and an instrument-airplane rating; or
6.1 Alternate Means to Obtain Ratings. › 6.1.5 Additionally, under § 194.216(b), applicants utilizing a Level C…
2. A rotorcraft category rating with a helicopter class rating and an instrument-helicopter rating.
6.1.4 Pilots seeking a Commercial Pilot Certificate with a powered-lift category rating in accordance with § 194.216(a) may log 35 hours of pilot-in-command (PIC) flight time in a powered-lift in lieu of the 50 hours of PIC flight time required by § 61.129(e)(1)(i).
6.1.5 Additionally, under § 194.216(b), applicants utilizing a Level C full flight simulator (FFS) or higher may credit 15 hours toward the 35-hour PIC flight time so long as:
1. The aeronautical experience was obtained in a Level C FFS or higher representing a powered-lift; and
2. The FFS sessions are conducted in accordance with:
a. A manufacturer’s proposed training curriculum for test pilots, instructor pilots,
FAA test pilots, or ASIs under § 194.217 or § 194.219;
b. The manufacturer’s training curriculum for the initial cadre of instructors under
§ 194.221; or
c. An approved training program under part 135, 141, or 142.
7.1.3 Training on the Areas of Operation Listed in § 61.127(b)(5) in a… › 7.1.3.1 An applicant for a Commercial Pilot Certificate with a…
CHAPTER 7. ALTERNATE AERONAUTICAL AND LOGGING EXPERIENCE
REQUIREMENTS FOR A COMMERCIAL PILOT CERTIFICATE WITH A
POWERED-LIFT CATEGORY RATING
7.1 Alternate Provisions for Test Pilots, FAA Test Pilots, Aviation Safety Inspectors (ASI), and Instructor Pilots.
7.1.1 Initial Experience During Aircraft Certification. Title 14 CFR part 194, §§ 194.217 and 194.219 provide alternate experience requirements for test pilots and instructor pilots of the manufacturer, as well as FAA test pilots and ASIs. To utilize these alternate experience requirements, the flights must be conducted in an experimental powered-lift at the manufacturer, and the applicant (i.e., the test pilot, FAA test pilot, ASI, or instructor pilot) must be authorized by the Administrator to act as pilot in command (PIC) of the experimental powered-lift. The specific alternate requirements are:
• PIC flight time;
• Training on the areas of operation listed in 14 CFR part 61, § 61.127(b)(5) in a powered-lift at the manufacturer; and
• Solo flight time or flight time performing the duties of PIC.
7.1.2 PIC Flight Time. Pursuant to §§ 194.217(c) and 194.219(c), a test pilot, an FAA test pilot, an ASI, or an instructor pilot may log PIC flight time for the purpose of satisfying the aeronautical experience requirements in §§ 61.129(e)(2)(ii) and 194.216(a) when the following conditions are met:
1. The instructor pilot, FAA test pilot, ASI, or test pilot is the sole manipulator of the controls of an experimental powered-lift for which the pilot is not rated;
2. The instructor pilot, FAA test pilot, ASI, or test pilot is acting as PIC of the experimental powered-lift in accordance with a Letter of Authorization (LOA) issued by the Administrator;
3. In the case of a test pilot, an FAA test pilot, or an ASI, the flight is conducted for the purposes of: (a) research and development (R&D), or (b) showing compliance with the regulations in accordance with the experimental certificate issued to the powered-lift; and
4. In the case of an instructor pilot, the flight is conducted for the purposes of crew training in accordance with the experimental certificate issued to the powered-lift.
7.1.3 Training on the Areas of Operation Listed in § 61.127(b)(5) in a Powered-Lift at the Manufacturer.
7.1.3.1 An applicant for a Commercial Pilot Certificate with a powered-lift category rating who has not received the 20 hours of flight training on the areas of operation listed in § 61.127(b)(5) from an authorized instructor may be considered eligible under the following two circumstances, as specified in § 194.217. In accordance with §§ 194.217(b)(1) and 194.219(b)(1), the
7.1.4 Solo Flight Time or Flight Time Performing the Duties of PIC. › 7.1.4.1 Each applicant is required to meet the requirements of §…
applicant must have satisfactorily completed the manufacturer’s proposed training curriculum. In the case of a test pilot, an FAA test pilot, or an ASI applicant, the training curriculum must have been provided by a pilot who serves as an instructor pilot in the experimental powered-lift. In the case of an instructor pilot applicant, the person must have provided the manufacturer’s proposed training curriculum in the experimental powered-lift. In either case, the applicant must receive a logbook or training record endorsement. In the case of a test pilot, an FAA test pilot, or an ASI applicant, this endorsement must be from an instructor pilot documenting completion of the manufacturer’s training curriculum. In the case of an instructor pilot, the endorsement must be from a management official within the manufacturer’s organization certifying the instructor pilot provided the training in accordance with the manufacturer’s proposed training curriculum. An example of the training record endorsement can be found in Appendix A, Example Endorsements.
7.1.3.2 Sections 194.217(b)(2) and 194.219(b)(2) permit an applicant for a Commercial Pilot Certificate with powered-lift category rating to be eligible for a certificate if they receive 3 hours of flight training in the experimental powered-lift in preparation for the practical test within the preceding 2 calendar months from the month of the test, if the training is received from an instructor pilot employed by the manufacturer of the experimental powered-lift.
7.1.3.3 Pursuant to §§ 194.217(b)(4) and 194.219(b)(4), test pilots, FAA test pilots, ASIs, or instructor pilots who do not meet the cross-country aeronautical experience requirements specified in § 61.129(e)(3)(ii) and (iii) may be considered eligible for a Commercial Pilot Certificate if they complete the cross-country requirements set forth by § 194.233(a). These requirements are detailed in Chapter 3, Alternate Cross-Country Requirements. The applicant must obtain a logbook or training record endorsement, as specified in § 194.213, from the instructor pilot or management official, as appropriate, certifying that the person completed the cross-country flight.
7.1.4 Solo Flight Time or Flight Time Performing the Duties of PIC.
7.1.4.1 Each applicant is required to meet the requirements of § 61.129(e)(4). In order to do this in a powered-lift that requires two pilots, §§ 194.217(b)(3) and 194.219(b)(3) enable alternative requirements. Specifically, a test pilot, an FAA test pilot, an ASI, or an instructor pilot applicant may log at least 10 hours of solo flight time under an endorsement from an instructor pilot or by performing the duties of PIC in an experimental powered-lift with either: (a) a test pilot for the manufacturer, or (b) an instructor pilot for the manufacturer. In either case, the additional test pilot or the instructor pilot must be authorized to act as the PIC of the experimental powered-lift.
7.1.4 Solo Flight Time or Flight Time Performing the Duties of PIC. › 7.1.4.3 In order to demonstrate compliance with the alternate…
7.1.4.2 When an applicant does not have the cross-country aeronautical experience specified in § 61.129(e)(4)(i), the applicant will still be considered eligible for a Commercial Pilot Certificate with powered-lift category rating if the applicant has logged at least two cross-country flights with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 nautical miles (NM) from the original point of departure. Section 194.233(b) details that the second cross-country flight, besides the original point of departure, must be performed to different points than the first cross-country flight.
7.1.4.3 In order to demonstrate compliance with the alternate requirements provided by part 194, the applicant must log this cross-country experience in their logbook as they would for any other certificate or rating in accordance with § 61.51(a).
Table 7-1. Alternate Provisions for a Commercial Pilot Certificate With a Powered-Lift
Category Rating: Test Pilots and Instructor Pilots
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS
FOR TEST PILOTS, FAA TEST PILOTS,
OR ASIs*
ALTERNATE PROVISIONS FOR INSTRUCTOR PILOTS*
*To use the alternate provisions below, the flights must be conducted in an experimental powered-lift at the manufacturer, and the test pilots and instructor pilots must be authorized by the Administrator to act as PIC of the experimental powered-lift. Refer to §§ 194.217(a) and 194.219(a).
Powered Aircraft Time
100 hours in powered aircraft, of which 50 hours must be in a powered-lift.
No alternative. No alternative.
PIC Flight Time
100 hours of PIC flight time, which includes at least:
(1) 50 hours in a
powered-lift, and
(2) 50 hours in cross-country
flight of which 10 must be in a powered-lift.
100 hours of PIC flight time, which includes at least:
(1) 35 hours in a powered-lift
of which 15 may be in a Level C or higher full flight simulator (FFS), and
(2) 50 hours in cross-country
flight of which 10 must be in a powered-lift.
A test pilot, an FAA test pilot, or an ASI who is not rated in the powered-lift may log PIC flight time in the experimental powered-lift if:
(1) The pilot is the sole
manipulator of the controls,
(2) The pilot is acting as PIC,
and
(3) The flight is conducted
for the purpose of R&D or showing compliance.
Refer to §§ 194.216 and 194.217(c).
100 hours of PIC flight time, which includes at least:
(1) 35 hours in a powered-lift
of which 15 may be in a Level C or higher FFS, and
(2) 50 hours in cross-country
flight of which 10 must be in a powered-lift.
An instructor pilot who is not rated in the powered-lift may log PIC flight time in the experimental powered-lift if:
(1) The instructor pilot is
acting as PIC, and
(2) The flight is conducted
for the purpose of crew training.
Refer to §§ 194.216 and 194.219(c).
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS
FOR TEST PILOTS, FAA TEST PILOTS,
OR ASIs*
ALTERNATE PROVISIONS FOR INSTRUCTOR PILOTS*
Training on the Areas of Operation Listed in § 61.127(b)(5)
20 hours of training on the areas of operation listed in § 61.127(b)(5) that includes at least:
A test pilot, an FAA test pilot, or an ASI may receive this training from an instructor pilot (rather than an authorized instructor) if:
(1) Training is conducted in
accordance with the manufacturer’s training curriculum, and
(2) The test pilot, FAA test
pilot, or ASI receive endorsement from the instructor pilot certifying satisfactory completion of the curriculum.
Refer to § 194.217(b)(1).
In lieu of receiving this training, an instructor pilot may meet this requirement by providing the manufacturer’s training curriculum to a test pilot, an FAA test pilot, or an ASI, which includes 20 hours of training on the areas of operation listed in § 61.127(b)(5). The instructor pilot must receive endorsement from a management official certifying that the instructor pilot provided the training.
Refer to § 194.219(b)(1).
(1) 10 hours of instrument
training using a view-limiting device, including attitude instrument flying, partial panel skills, recovery from unusual flight attitudes, and intercepting and tracking navigational systems. 5 hours of the 10 hours required on instrument training must be in a powered-lift.
A test pilot, an FAA test pilot, or an ASI may receive this instrument training from an instructor pilot in an experimental powered-lift in accordance with the manufacturer’s proposed training curriculum.
Refer to § 194.217(b)(1).
An instructor pilot may satisfy this requirement by providing instrument training to a test pilot, an FAA test pilot, or an ASI in accordance with the manufacturer’s proposed training curriculum. The instructor pilot must receive an endorsement from a management official certifying that the instructor pilot provided the training.
Refer to § 194.219(b)(1).
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS
FOR TEST PILOTS, FAA TEST PILOTS,
OR ASIs*
ALTERNATE PROVISIONS FOR INSTRUCTOR PILOTS*
(2) The following cross-country
flights:
• One 2-hour cross-country flight in a powered-lift in daytime conditions that consists of a total straight-line distance of more than 100 NM from the original point of departure; and
• One 2-hour cross-country flight in a powered-lift in nighttime conditions that consists of a total straight-line distance of more than 100 NM from the original point of departure.
A test pilot, an FAA test pilot, or an ASI may complete the following cross-country flights:
• One 2-hour cross-country flight in a powered-lift in daytime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure;
• One 2-hour cross-country flight in a powered-lift in nighttime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure; and
• An additional cross-country flight with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. The additional cross-country flight must include landings at different points than the first two cross-country flights.
Refer to § 194.233(a).
An instructor pilot may complete the same alternate cross-country flights as a test pilot, an FAA test pilot, or an ASI.
Refer to § 194.233(a).
(3) 3 hours in a powered-lift with
an authorized instructor in preparation for the practical test within the preceding 2 calendar months from the month of the test.
A test pilot, an FAA test pilot, or an ASI may accomplish the practical test preparation with an instructor pilot (rather than an authorized instructor).
Refer to § 194.217(b)(2).
An instructor pilot may accomplish the practical test preparation with another instructor pilot (rather than an authorized instructor).
Refer to § 194.219(b)(2).
7.2 Alternate Provisions for Initial Cadre of Instructors. › 7.2.1 Facilitation of Training.
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS
FOR TEST PILOTS, FAA TEST PILOTS,
OR ASIs*
ALTERNATE PROVISIONS FOR INSTRUCTOR PILOTS*
Solo Flight Time or Flight Time Performing the Duties of PIC
10 hours of solo flight time in a powered-lift or 10 hours of flight time performing the duties of PIC in a powered-lift with an authorized instructor on board (either of which may be credited toward the flight time requirement under § 61.129(e)(2), on the areas of operation listed in § 61.127(b)(5)) that includes:
A test pilot, an FAA test pilot, or an ASI may complete 10 hours of solo flight time under an endorsement from an instructor pilot or 10 hours of flight time performing the duties of PIC in a powered-lift with either a test pilot or an instructor pilot on board.
Refer to § 194.217(b)(3).
The alternate provision for test pilots, FAA test pilots, or ASIs also applies to instructor pilots.
Refer to § 194.219(b)(3).
(1) One cross-country flight of
not less than 300 NM total distance with landings at a minimum of three points, one of which is a straight-line distance of at least 250 NM from the original departure point. However, if this requirement is being met in Hawaii, the longest segment need only have a straight-line distance of at least 150 NM.
A test pilot, an FAA test pilot, or an ASI may complete two cross-country flights with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. The second cross-country flight must include landings at different points than the first cross-country flight.
Refer to § 194.233(b).
An instructor pilot may complete the same alternate cross-country flights as a test pilot, an FAA test pilot, or an ASI.
Refer to § 194.233(b).
(2) 5 hours in night visual flight
rules (VFR) conditions with 10 takeoffs and 10 landings (with each landing involving a flight in the traffic pattern) at an airport with an operating control tower.
No alternative. No alternative.
7.2 Alternate Provisions for Initial Cadre of Instructors.
7.2.1 Facilitation of Training. Once the manufacturer has completed type certification of their powered-lift, SFAR 120 facilitates manufacturers providing training for an initial cadre of instructors employed at specific certificate holders (CH). The manufacturer’s training curriculum will cover all the required areas of operation for certification, and the manufacturer’s instructor pilots may deliver this training. This approach of facilitating the
7.2.2 Authorization. › 7.2.2.2 PIC Flight Time.
use of instructor pilots at the manufacturer to deliver initial certification training to the first powered-lift applicants enables those most familiar with the aircraft (i.e., the manufacturers) to provide safe and effective training and provides the manufacturer the means to ensure that there are a sufficient number of qualified pilots to operate their aircraft and train other pilots to operate their aircraft.
7.2.2 Authorization. In accordance with § 194.221(a), the initial cadre instructor applicant must be authorized by the Administrator to serve as an initial check pilot, a chief instructor, an assistant chief instructor, or a Training Center Evaluator (TCE) for the purpose of initiating training in a powered-lift under an approved training program under 14 CFR part 135, 141, or 142, as appropriate. The CH should submit a request to the responsible Flight Standards office. Upon authorization, these applicants will receive a temporary LOA from the Administrator to receive this training. As set forth by § 194.221 and subsequently explained in the paragraphs below, the applicant must satisfactorily complete the training curriculum, and the training must be provided by the manufacturer in a type-certificated powered-lift with a pilot who serves as an instructor pilot for that manufacturer.
7.2.2.1 Initial Experience for Initial Cadre Instructors. Section 194.221 sets forth the alternate experience requirements for the initial cadre of instructors. These specific alternate requirements are:
• PIC flight time,
• Training on the areas of operation listed in § 61.127(b)(5) in a powered-lift at the manufacturer, and
• Solo flight time or flight time performing the duties of PIC.
7.2.2.2 PIC Flight Time. Section 194.221(c) authorizes an initial cadre instructor applicant who is not rated in the powered-lift to log up to 25 hours of the required 35 hours of PIC flight time in a powered-lift for flights conducted in accordance with a manufacturer’s training curriculum if the applicant is:
• The sole manipulator of the controls,
• Manipulating the controls of the powered-lift with an instructor pilot on board, and
• Performing the duties of PIC.
Note: The last 10 hours of the required 35 hours must be either solo or performing the duties of PIC with an authorized instructor or instructor pilot on board.
7.2.2.4 Solo Flight Time or Flight Time Performing the Duties of PIC. › 7.2.2.4.3 To demonstrate compliance with the alternate requirements…
7.2.2.3 Training on the Areas of Operation Listed in § 61.127(b)(5) in a Powered-Lift at the Manufacturer.
7.2.2.3.1 Section 194.221(b)(1) authorizes an initial cadre instructor applicant to receive training from an instructor pilot (rather than an authorized instructor) in a type-certificated powered-lift at a manufacturer in accordance with the manufacturer’s training curriculum, if the curriculum includes 20 hours of training on the areas of operation listed in § 61.127(b)(5).
7.2.2.3.2 Section 194.221(b)(2) permits an initial cadre instructor applicant to receive 3 hours of flight training in the type-certificated powered-lift in preparation for the practical test within the preceding 2 calendar months from the month of the test, if it is received from an instructor pilot employed by the manufacturer.
7.2.2.3.3 Pursuant to § 194.221(b)(4), an initial cadre instructor applicant who does not meet the cross-country aeronautical experience requirements specified in § 61.129(e)(3)(ii) and (iii) will still be considered eligible for a Commercial Pilot Certificate if they complete the cross-country requirements listed in § 194.233(a). These requirements are detailed in Chapter 3.
7.2.2.3.4 The initial cadre instructor applicant must obtain a logbook or training record endorsement, as specified in § 194.213, from the instructor pilot certifying that the person completed the cross-country flight.
7.2.2.4 Solo Flight Time or Flight Time Performing the Duties of PIC.
7.2.2.4.1 Each initial cadre instructor applicant must meet the requirements of § 61.129. These requirements include completing 10 hours of solo flight time in a powered-lift. Because solo flight time is not possible in a powered-lift that requires two pilots, § 194.221(b)(3) established an alternative requirement. Specifically, an applicant in the initial cadre group may log at least 10 hours of solo flight time in a powered-lift under an endorsement from an instructor pilot or by performing the duties of the PIC with an instructor pilot on board.
7.2.2.4.2 If an initial cadre instructor applicant does not have the cross-country aeronautical experience specified in § 61.129(e)(4)(i), the applicant may be considered eligible for a Commercial Pilot Certificate with powered-lift category rating if the applicant has logged at least two cross-country flights with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. Section 194.233(b) details that the second cross-country flight, besides the original point of departure, must be performed to different points than the first cross-country flight.
7.2.2.4.3 To demonstrate compliance with the alternate requirements provided by part 194, the initial cadre instructor applicant must log this cross-country experience in their logbook as they would for any other certificate.
7.2.2.4 Solo Flight Time or Flight Time Performing the Duties of PIC. › 7.2.2.4.4 Once the initial cadre instructor applicant completes the…
7.2.2.4.4 Once the initial cadre instructor applicant completes the manufacturer’s training curriculum, they will receive a logbook or training record endorsement from the instructor pilot certifying that they satisfactorily completed the training in accordance with § 194.221(b)(1)(ii).
Table 7-2. Alternate Provisions for a Commercial Pilot Certificate With a Powered-Lift
Category Rating: Initial Cadre of Check Pilots, Chief Instructors, Assistant Chief
Instructors, and Training Center Evaluators (Initial Cadre Instructors)
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR INITIAL CADRE OF CHECK PILOTS,
CHIEF INSTRUCTORS, ASSISTANT CHIEF INSTRUCTORS,
AND TCEs* (initial cadre instructors, herein referred to
as applicants)
*To use the alternate provisions below, the flights must be conducted by an instructor pilot in a type-certificated powered-lift at the manufacturer, and the applicant must be authorized by the Administrator to serve as an initial check pilot, a chief instructor, an assistant chief instructor, or a TCE for the purpose of initiating training in a powered-lift under an approved training program under part 135, 141, or 142, as appropriate. Refer to § 194.221(a).
Powered Aircraft Time
100 hours in powered aircraft, of which 50 hours must be in a powered-lift. No alternative.
PIC Flight Time
100 hours of PIC flight time, which includes at least:
(1) 50 hours in a powered-lift, and
(2) 50 hours in cross-country flight of
which 10 must be in a powered-lift.
100 hours of PIC flight time, which includes at least:
(1) 35 hours in a powered-lift, 15 of which
may be in a Level C or higher FFS, and
(2) 50 hours in cross-country flight of
which 10 must be in a powered-lift.
An applicant who is not rated in the powered-lift may log up to 25 hours of PIC flight time in a powered-lift for flights that are conducted in accordance with a manufacturer’s training curriculum if the applicant is:
(1) The sole manipulator of the controls,
(2) Manipulating the controls of the
powered-lift with an instructor pilot on board, and
(3) Performing the duties of PIC.
Refer to §§ 194.216 and 194.221(c).
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR INITIAL CADRE OF CHECK PILOTS,
CHIEF INSTRUCTORS, ASSISTANT CHIEF INSTRUCTORS,
AND TCEs* (initial cadre instructors, herein referred to
as applicants)
Training on the Areas of Operation Listed in § 61.127(b)(5)
20 hours of training on the areas of operation listed in § 61.127(b)(5) that includes at least:
An applicant may receive this training from an instructor pilot (rather than an authorized instructor) if:
(1) Training is conducted in accordance
with the manufacturer’s training curriculum, and
(2) The applicant receives an endorsement
from an instructor pilot certifying satisfactory completion of the curriculum.
Refer to § 194.221(b)(1).
(1) 10 hours of instrument training using a
view-limiting device, including attitude instrument flying, partial panel skills, recovery from unusual flight attitudes, and intercepting and tracking navigational systems. 5 hours of the 10 hours required on instrument training must be in a powered-lift.
An applicant may receive this instrument training from an instructor pilot in a type-certificated powered-lift in accordance with the manufacturer’s training curriculum.
Refer to § 194.221(b)(1).
(2) The following cross-country flights:
• One 2-hour cross-country flight in a powered-lift in daytime conditions that consists of a total straight-line distance of more than 100 NM from the original point of departure; and
• One 2-hour cross-country flight in a powered-lift in nighttime conditions that consists of a total straight-line distance of more than 100 NM from the original point of departure.
An applicant may complete the following cross-country flights:
• One 2-hour cross-country flight in a powered-lift in daytime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure;
• One 2-hour cross-country flight in a powered-lift in nighttime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure; and
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR INITIAL CADRE OF CHECK PILOTS,
CHIEF INSTRUCTORS, ASSISTANT CHIEF INSTRUCTORS,
AND TCEs* (initial cadre instructors, herein referred to
as applicants)
• An additional cross-country flight with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. The additional cross-country flight must include landings at different points than the first two cross-country flights.
Refer to § 194.233(a).
(3) 3 hours in a powered-lift with an authorized
instructor in preparation for the practical test within the preceding 2 calendar months from the month of the test.
An applicant may accomplish the practical test preparation from an instructor pilot (rather than an authorized instructor).
Refer to § 194.221(b)(2).
Solo Flight Time or Flight Time Performing the Duties of PIC
10 hours of solo flight time in a powered-lift or 10 hours of flight time performing the duties of PIC in a powered-lift with an authorized instructor on board (either of which may be credited toward the flight time requirement under § 61.129(e)(2), on the areas of operation listed in § 61.127(b)(5)) that includes:
An applicant may complete 10 hours of solo flight time under an endorsement from an instructor pilot or 10 hours of flight time performing the duties of PIC in a powered-lift with an instructor pilot on board (rather than an authorized instructor).
Refer to § 194.221(b)(3).
(1) One cross-country flight of not less than
300 NM total distance with landings at a minimum of three points, one of which is a straight-line distance of at least 250 NM from the original departure point. However, if this requirement is being met in Hawaii, the longest segment need only have a straight-line distance of at least 150 NM.
An applicant may complete two cross-country flights with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. The second cross-country flight must include landings at different points than the first cross-country flight.
Refer to § 194.233(b).
7.3.1 PIC Flight Time. › 7.3.1.1 Section 194.223(c) authorizes an applicant who is not rated in…
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR INITIAL CADRE OF CHECK PILOTS,
CHIEF INSTRUCTORS, ASSISTANT CHIEF INSTRUCTORS,
AND TCEs* (initial cadre instructors, herein referred to
as applicants)
(2) 5 hours in night VFR conditions with
10 takeoffs and 10 landings (with each landing involving a flight in the traffic pattern) at an airport with an operating control tower.
No alternative.
7.3 Alternate Provisions for Pilots Trained in an Approved Training Program at the CH. Newly certificated initial cadre flight instructors for an operator, a pilot school, or a training center (i.e., part 135 check pilots, part 141 chief instructors or assistant chief instructors, or part 142 TCEs who have been trained and certified at the manufacturer) will be proficient in the training curriculum under their respective part because of their involvement in developing the proposed training program. This involvement will enable them to be in the best position to provide training to pilots enrolled in their respective CH’s training program under part 135, 141, or 142. The initial cadre of flight instructors will become fully qualified to serve in their designated function and receive a permanent LOA from the Administrator to subsequently conduct the training.
Because these pilots will now be authorized instructors (i.e., meet the requirements for instructors under their respective part), the pilots who will receive training under an approved training program do not require the same breadth of relief that instructor pilots, test pilots, and the initial cadre instructors need. Rather, the only relief necessary for pilots enrolled in an approved training program is that of logging, flight simulation training device (FSTD) credit, and the cross-country relief in § 194.233 extended to all applicants, which would require the trainer to hold a flight instructor certificate. See Chapter 11, Part 91K Requirements to Serve as a Powered-Lift Pilot in a Fractional Ownership Program, and Chapter 12, Requirements to Serve as a Powered-Lift Pilot Under Part 135, for additional information.
7.3.1 PIC Flight Time.
7.3.1.1 Section 194.223(c) authorizes an applicant who is not rated in the powered-lift to log up to 25 hours of the required 35 hours of PIC flight time in a powered-lift for flights that are conducted in accordance with an approved training program under part 135, 141, or 142 if the applicant is:
• The sole manipulator of the controls,
• Manipulating the controls of the powered-lift with an authorized instructor on board, and
• Performing the duties of PIC.
7.3 Alternate Provisions for Pilots Trained in an Approved Training… › 7.3.3 Solo Flight Time or Flight Time Performing the Duties of PIC.
Note: The last 10 hours of the required 35 hours must be either solo or performing the duties of PIC with an authorized instructor or instructor pilot on board.
7.3.1.2 Section 194.216 allows an applicant to credit up to 15 hours of flight time obtained in a Level C or higher FFS toward the requirement to obtain 35 hours of PIC flight time in a powered-lift if:
• The FFS represents the powered-lift category, and
• The applicant was performing the duties of PIC.
7.3.2 Training on the Areas of Operation Listed in § 61.127(b)(5) in a Powered-Lift. Applicants who do not meet the cross-country aeronautical experience requirements specified in § 61.129(e)(3)(ii) and (iii) may be considered eligible for a Commercial Pilot Certificate if they complete the cross-country requirements as specified in § 194.233(a). These requirements are detailed in Chapter 3.
7.3.3 Solo Flight Time or Flight Time Performing the Duties of PIC. If an applicant does not have the cross-country aeronautical experience specified in § 61.129(e)(4)(i), the applicant may be considered eligible for a Commercial Pilot Certificate with powered-lift category rating if the applicant has logged at least two cross-country flights with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. Section 194.233(b) details that the second cross-country flight, besides the original point of departure, must be performed to different points than the first cross-country flight.
Table 7-3. Alternate Provisions for a Commercial Pilot Certificate With a Powered-Lift
Category Rating: Persons Receiving Training Under a Part 135, 141, or 142
Approved Training Program
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR PERSONS RECEIVING TRAINING
UNDER A PART 135, 141, OR 142 APPROVED TRAINING PROGRAM*
(herein referred to as applicants)
*To use the alternate provisions below, the applicant must receive training at an approved training program under part 135, 141, or 142 for the purpose of obtaining a powered-lift category rating.
Powered Aircraft Time
100 hours in powered aircraft, of which 50 hours must be in a powered-lift. No alternative.
PIC Flight Time
100 hours of PIC flight time, which includes at least:
(1) 50 hours in a powered-lift, and
(2) 50 hours in cross-country flight of
which 10 must be in a powered-lift.
100 hours of PIC flight time, which includes at least:
(1) 35 hours in a powered-lift, 15 of which
may be in a Level C or higher FFS, and
(2) 50 hours in cross-country flight of
which 10 must be in a powered-lift.
An applicant who is not rated in the powered-lift may log up to 25 hours of PIC flight time in a powered-lift for flights that are conducted in accordance with an approved training program under part 135, 141, or 142 if the applicant is:
(1) The sole manipulator of the controls,
(2) Manipulating the controls of the
powered-lift with an authorized instructor on board, and
(3) Performing the duties of PIC.
Refer to §§ 194.216 and 194.223(c).
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR PERSONS RECEIVING TRAINING
UNDER A PART 135, 141, OR 142 APPROVED TRAINING PROGRAM*
(herein referred to as applicants)
Training on the Areas of Operation Listed in § 61.127(b)(5)
20 hours of training on the areas of operation listed in § 61.127(b)(5) that includes at least:
No alternative.
(1) 10 hours of instrument training using a
view-limiting device, including attitude instrument flying, partial panel skills, recovery from unusual flight attitudes, and intercepting and tracking navigational systems. 5 hours of the 10 hours required on instrument training must be in a powered-lift.
No alternative.
(2) The following cross-country flights:
• One 2-hour cross-country flight in a powered-lift in daytime conditions that consists of a total straight-line distance of more than 100 NM from the original point of departure; and
• One 2-hour cross-country flight in a powered-lift in nighttime conditions that consists of a total straight-line distance of more than 100 NM from the original point of departure.
An applicant may complete the following cross-country flights:
• One 2-hour cross-country flight in a powered-lift in daytime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure;
• One 2-hour cross-country flight in a powered-lift in nighttime conditions that consists of a total straight-line distance of more than 50 NM from the original point of departure; and
• An additional cross-country flight with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. The additional cross-country flight must include landings at different points than the first two cross-country flights.
Refer to § 194.233(a).
(3) 3 hours in a powered-lift with an
authorized instructor in preparation for the practical test within the preceding 2 calendar months from the month of the test.
No alternative.
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR PERSONS RECEIVING TRAINING
UNDER A PART 135, 141, OR 142 APPROVED TRAINING PROGRAM*
(herein referred to as applicants)
Solo Flight Time or Flight Time Performing the Duties of PIC
10 hours of solo flight time in a powered-lift or 10 hours of flight time performing the duties of PIC in a powered-lift with an authorized instructor on board (either of which may be credited toward the flight time requirement under § 61.129(e)(2), on the areas of operation listed in § 61.127(b)(5)) that includes:
No alternative.
(1) One cross-country flight of not less than
300 NM total distance with landings at a minimum of three points, one of which is a straight-line distance of at least 250 NM from the original departure point. However, if this requirement is being met in Hawaii, the longest segment need only have a straight-line distance of at least 150 NM.
An applicant may complete two cross-country flights with landings at a minimum of three points, with one segment consisting of a straight-line distance of at least 50 NM from the original point of departure. The second cross-country flight must include landings at different points than the first cross-country flight.
Refer to § 194.233(b).
(2) 5 hours in night VFR conditions with
10 takeoffs and 10 landings (with each landing involving a flight in the traffic pattern) at an airport with an operating control tower.
No alternative.
8.1.3 Instrument Training on the Areas of Operation Listed in §… › 8.1.3.1 An applicant for an instrument-powered-lift rating who has not…
CHAPTER 8. ALTERNATE AERONAUTICAL EXPERIENCE AND LOGGING
REQUIREMENTS FOR AN INSTRUMENT-POWERED-LIFT RATING
8.1 Alternate Provisions for Test Pilots, FAA Test Pilots, Aviation Safety Inspectors (ASI), and Instructor Pilots.
8.1.1 Initial Experience During Aircraft Certification. Title 14 CFR part 194, §§ 194.225 and 194.227 provide certain alternate experience requirements for an instrument-powered-lift rating for test pilots, FAA test pilots, ASIs, and instructor pilots. To utilize these alternate experience requirements, the flights must be conducted at an experimental powered-lift at the manufacturer, and the applicant (i.e., the test pilot, FAA test pilot, ASI, or instructor pilot) must be authorized by the Administrator to act as pilot in command (PIC) of the experimental powered-lift. The alternate experience requirements include cross-country time as PIC, and instrument time on the areas of operation listed in 14 CFR part 61, § 61.65(c).
8.1.2 Alternate Logging Requirements. Pursuant to §§ 194.225(c) and 194.227(c), a test pilot, an FAA test pilot, an ASI, or an instructor pilot may log PIC flight time for the purpose of satisfying the aeronautical experience requirements in § 61.65(f)(1) when the following conditions are met:
1. The instructor pilot, FAA test pilot, ASI, or test pilot is the sole manipulator of the controls of an experimental powered-lift for which the pilot is not rated;
2. The instructor pilot, FAA test pilot, ASI, or test pilot is acting as PIC of the experimental powered-lift in accordance with a Letter of Authorization (LOA) issued by the Administrator;
3. In the case of a test pilot, an FAA test pilot, or an ASI, the flight is conducted for the purposes of (a) research and development (R&D), or (b) showing compliance with the regulations in accordance with the experimental certificate issued to the powered-lift; and
4. In the case of an instructor pilot, the flight is conducted for the purposes of crew training in accordance with the experimental certificate issued for the powered-lift.
8.1.3 Instrument Training on the Areas of Operation Listed in § 61.65(c).
8.1.3.1 An applicant for an instrument-powered-lift rating who has not received the 15 hours of instrument training on the areas of operation listed in § 61.65(c) from an authorized instructor may be considered eligible under the following two circumstances. In the case of a test pilot, an FAA test pilot, or an ASI, and in accordance with § 194.225(b)(1), test pilots, FAA test pilots, and ASIs may receive the instrument training from an instructor pilot in an experimental powered-lift in accordance with the manufacturer’s proposed training curriculum if the test pilot, FAA test pilot, or ASI is authorized to act as PIC of the powered-lift and the curriculum includes 15 hours of instrument training on the areas of operation listed in § 61.65(c). In the case of an instructor pilot, the person must have provided the manufacturer’s proposed
8.1.3 Instrument Training on the Areas of Operation Listed in §… › 8.1.3.4 All flights recorded in the applicant’s logbook will include…
training curriculum in the experimental powered-lift. In either case, the applicant must receive a logbook or training record endorsement. In the case of a test pilot, an FAA test pilot, or an ASI applicant, this endorsement must be from an instructor pilot documenting completion of the manufacturer’s training curriculum. In the case of an instructor pilot, the endorsement must be from a management official within the manufacturer’s organization certifying the instructor pilot provided the training in accordance with the manufacturer’s proposed training curriculum. An example of the training record endorsement can be found in Appendix A, Example Endorsements.
8.1.3.2 Sections 194.225(b)(2) and 194.227(b)(2) authorize an applicant for an instrument rating in a powered-lift to receive 3 hours of instrument training from an instructor pilot in the experimental powered-lift in preparation for the practical test within the preceding 2 calendar months from the month of the test.
8.1.3.3 Sections 194.225(b)(4) and 194.227(b)(4) permit test pilots, FAA test pilots, ASIs, and instructor pilots who do not meet the cross-country aeronautical experience requirements specified in § 61.65(f)(2)(ii) to be eligible for an instrument rating if they complete the cross-country requirements set forth by § 194.235. These requirements are detailed in Chapter 3, Alternate Cross-Country Requirements.
8.1.3.4 All flights recorded in the applicant’s logbook will include the requirements listed in § 194.213(b). This experience will be presented to an evaluator or inspector as part of the applicant’s verification of records for a practical test.
Table 8-1. Alternate Provisions for an Instrument-Powered-Lift Rating: Test Pilots and
Instructor Pilots
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR
TEST PILOTS, FAA TEST PILOTS,
OR ASIs*
ALTERNATE PROVISIONS FOR INSTRUCTOR PILOTS*
*To use the alternate provisions below, the flights must be conducted in an experimental powered-lift at the manufacturer, and the test pilots, FAA test pilots, ASIs, and instructor pilots must be authorized by the Administrator to act as PIC of the experimental powered-lift. Refer to §§ 194.225(a) and 194.227(a).
Cross-Country Time as PIC
50 hours of cross-country time as PIC, of which 10 hours must have been in a powered-lift.
A test pilot, an FAA test pilot, or an ASI who is not rated in the powered-lift may log PIC flight time in the experimental powered-lift toward the 10-hour cross-country time requirement if:
(1) The test pilot, FAA test
pilot, or ASI is the sole manipulator of the controls;
(2) The test pilot, FAA test
pilot, or ASI is acting as PIC of the powered-lift; and
(3) The flight is conducted
for the purpose of R&D or showing compliance.
Refer to § 194.225(c).
An instructor pilot who is not rated in the powered-lift may log PIC flight time in the experimental powered-lift toward the 10-hour cross-country time requirement if:
(1) The instructor pilot is
acting as PIC of the powered-lift, and
(2) The flight is conducted
for the purpose of crew training.
Refer to § 194.227(c).
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR
TEST PILOTS, FAA TEST PILOTS,
OR ASIs*
ALTERNATE PROVISIONS FOR INSTRUCTOR PILOTS*
Instrument Time on the Areas of Operation Listed in § 61.65(c)
40 hours of actual or simulated instrument time in the areas of operation listed in § 61.65(c), of which 15 hours must have been received from an authorized instructor who holds an instrument-powered-lift rating, and the instrument time includes:
A test pilot, an FAA test pilot, or an ASI may receive 15 hours of instrument training on the areas of operation listed in § 61.65(c) from an instructor pilot (rather than an authorized instructor) if:
(1) The training is
conducted in accordance with the manufacturer’s proposed training curriculum, and
(2) The test pilot, FAA test
pilot, or ASI receives an endorsement from an instructor pilot certifying satisfactory completion of the curriculum.
Refer to § 194.225(b)(1).
In lieu of receiving the 15 hours of instrument training on the areas of operation listed in § 61.65(c), an instructor pilot may provide this instrument training to the test pilot in accordance with the manufacturer’s proposed training curriculum. The instructor pilot must receive endorsement from a management official certifying that the instructor pilot provided the training.
Refer to § 194.227(b)(1).
(1) 3 hours of instrument flight
training from an authorized instructor in a powered-lift that is appropriate to the instrument-powered-lift rating within 2 calendar months before the date of the practical test.
A test pilot, an FAA test pilot, or an ASI may accomplish the practical test preparation with an instructor pilot (rather than an authorized instructor).
Refer to § 194.225(b)(2).
An instructor pilot may accomplish the practical test preparation with another instructor pilot (rather than an authorized instructor).
Refer to § 194.227(b)(2).
8.2 Alternate Provisions for Initial Cadre of Instructors. › 8.2.2 Authorization.
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR
TEST PILOTS, FAA TEST PILOTS,
OR ASIs*
ALTERNATE PROVISIONS FOR INSTRUCTOR PILOTS*
(2) Instrument flight training
on cross-country flight procedures, including one cross-country flight in a powered-lift with an authorized instructor that is performed under instrument flight rules (IFR), when a flight plan has been filed with an air traffic control (ATC) facility, that involves:
• A flight of 250 nautical miles (NM) along airways or by directed routing from an ATC facility;
• An instrument approach at each airport; and
• Three different kinds of approaches with the use of navigation systems.
A test pilot, an FAA test pilot, or an ASI may complete the cross-country flight with an instructor pilot (rather than an authorized instructor).
Instead of completing one cross-country flight of 250 NM, a test pilot, an FAA test pilot, or an ASI may complete two cross-country flights, each of which must involve a flight of 100 NM along airways or by directed routing from an ATC facility.
Refer to §§ 194.225(b)(4) and 194.235(a).
An instructor pilot may complete the cross-country flight with another instructor pilot (rather than an authorized instructor).
An instructor pilot may complete the same alternate cross-country flights as a test pilot.
Refer to §§ 194.227(b)(4) and 194.235(a).
8.2 Alternate Provisions for Initial Cadre of Instructors.
8.2.1 Facilitation of Training. Once the manufacturer has completed type certification of their powered-lift, SFAR 120 facilitates manufacturers providing training for an initial cadre of instructors employed at specific certificate holders (CH). The manufacturer’s approved training curriculum will cover all the required areas of operation, and the manufacturer’s instructor pilots may deliver this training. This approach of facilitating the use of instructor pilots at the manufacturer to deliver initial certification training to the first powered-lift applicants enables those most familiar with the aircraft (i.e., the manufacturers) to provide safe and effective training and provides the manufacturer the means to ensure that there are a sufficient number of qualified pilots to operate their aircraft and train other pilots to operate their aircraft.
8.2.2 Authorization. In accordance with § 194.229(a), the initial cadre instructor applicant must be authorized by the Administrator to serve as an initial check pilot, a chief instructor, an assistant chief instructor, or a Training Center Evaluator (TCE) for the purpose of
initiating training in a powered-lift under an approved training program under 14 CFR part 135, 141, or 142, as appropriate. The CH should submit a request to the responsible Flight Standards office. Upon authorization, these applicants will receive a temporary LOA from the Administrator to receive this training. As set forth by § 194.229 and subsequently explained in the paragraphs below, the applicant must satisfactorily complete that training curriculum, and the training must be provided by the manufacturer in a type-certificated powered-lift with a pilot who serves as an instructor pilot for that manufacturer.
8.2.2.3 Instrument Training on the Areas of Operation Listed in §… › 8.2.2.3.4 Pursuant to § 194.229(b)(4), an initial cadre instructor…
8.2.2.1 Initial Experience for Initial Cadre Instructors. Section 194.229 provides alternate experience requirements for the initial cadre instructors. These specific alternate requirements are:
• Cross-country time as PIC, and
• Instrument training on the areas of operation listed in § 61.65(c).
8.2.2.2 Alternate Logging Requirement. Section 194.229(c) authorizes an initial cadre instructor applicant who is not rated in the powered-lift to log PIC flight time in the powered-lift toward the 10-hour cross-country time requirement for flights that are conducted in accordance with a manufacturer’s training curriculum if the applicant is:
• The sole manipulator of the controls with an instructor pilot on board, and
• Performing the duties of PIC.
8.2.2.3 Instrument Training on the Areas of Operation Listed in § 61.65(c).
8.2.2.3.1 Section 194.229(b)(1) authorizes an initial cadre instructor applicant to receive instrument training from an instructor pilot (rather than an authorized instructor) in a type-certificated powered-lift at a manufacturer in accordance with the manufacturer’s training curriculum, if the curriculum covers the areas of operation listed in § 61.65(c).
8.2.2.3.2 Initial cadre instructor applicants may be eligible for an instrument-powered-lift rating once they complete the manufacturer’s proposed training curriculum for that aircraft and records documenting that completion are made available to an evaluator.
8.2.2.3.3 Section 194.229(b)(2) permits the initial cadre instructor applicant to receive 3 hours of instrument training in a type-certificated powered-lift at a manufacturer in preparation for the practical test within the preceding 2 calendar months from the month of the test, if it is received from an instructor pilot employed by the manufacturer.
8.2.2.3.4 Pursuant to § 194.229(b)(4), an initial cadre instructor applicant who does not meet the cross-country aeronautical experience requirements specified in § 61.65(f)(2)(ii) may be considered eligible for an instrument rating if they
complete the cross-country requirements listed in § 194.235. These requirements are detailed in Chapter 3.
8.2.2.3 Instrument Training on the Areas of Operation Listed in §… › 8.2.2.3.6 Once the initial cadre instructor satisfactorily completes…
8.2.2.3.5 The initial cadre instructor applicant must obtain a logbook or training record endorsement from the instructor pilot certifying that the person completed the cross-country flight, as specified in § 194.213.
8.2.2.3.6 Once the initial cadre instructor satisfactorily completes the manufacturer’s training curriculum, they will receive a logbook or training record endorsement from the instructor pilot certifying that they satisfactorily completed the training in accordance with § 194.229(b)(1)(ii).
Table 8-2. Alternate Provisions for an Instrument-Powered-Lift Rating: Initial Cadre of
Check Pilots, Chief Instructors, Assistant Chief Instructors, and Training Center
Evaluators (Initial Cadre Instructors)
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR INITIAL CADRE OF CHECK PILOTS,
CHIEF INSTRUCTORS, ASSISTANT CHIEF INSTRUCTORS,
AND TCEs* (initial cadre instructors, herein referred to
as applicants)
*To use the alternate provisions below, the flights must be conducted by an instructor pilot in a type-certificated powered-lift at the manufacturer, and the applicant must be authorized by the Administrator to serve as an initial check pilot, a chief instructor, an assistant chief instructor, or a TCE for the purpose of initiating training in a powered-lift under an approved training program under part 135, 141, or 142, as appropriate. Refer to § 194.229(a).
Cross-Country Time as PIC
50 hours of cross-country time as PIC, of which 10 hours must have been in a powered-lift.
An applicant who is not rated in the powered-lift may log PIC flight time in the powered-lift toward the 10-hour cross-country time requirement for flights that are conducted in accordance with a manufacturer’s training curriculum if the applicant is:
(1) The sole manipulator of the controls,
(2) Manipulating the controls of the
powered-lift with an instructor pilot on board, and
(3) Performing the duties of PIC.
Refer to § 194.229(c).
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR INITIAL CADRE OF CHECK PILOTS,
CHIEF INSTRUCTORS, ASSISTANT CHIEF INSTRUCTORS,
AND TCEs* (initial cadre instructors, herein referred to
as applicants)
Instrument Time on the Areas of Operation Listed in § 61.65(c)
40 hours of actual or simulated instrument time in the areas of operation listed in § 61.65(c), of which 15 hours must have been received from an authorized instructor who holds an instrument-powered-lift rating, and the instrument time includes:
An applicant may receive 15 hours of instrument training on the areas of operation listed in § 61.65(c) from an instructor pilot (rather than an authorized instructor) if:
(1) The training is conducted in accordance
with the manufacturer’s training curriculum, and
(2) The applicant receives an endorsement
from an instructor pilot certifying satisfactory completion of the curriculum.
Refer to § 194.229(b)(1).
(1) 3 hours of instrument flight training
from an authorized instructor in a powered-lift that is appropriate to the instrument-powered-lift rating within 2 calendar months before the date of the practical test.
An applicant may accomplish the practical test preparation from an instructor pilot (rather than an authorized instructor).
Refer to § 194.229(b)(2).
(2) Instrument flight training on cross-country
flight procedures, including one cross-country flight in a powered-lift with an authorized instructor that is performed under IFR, when a flight plan has been filed with an ATC facility, that involves:
• A flight of 250 NM along airways or by directed routing from an ATC facility;
• An instrument approach at each airport; and
• Three different kinds of approaches with the use of navigation systems.
An applicant may complete the cross-country flight with an instructor pilot (rather than an authorized instructor).
Instead of completing one cross-country flight of 250 NM, an applicant may complete two cross-country flights, each of which must involve a flight of 100 NM along airways or by directed routing from an ATC facility.
Refer to §§ 194.229(b)(4) and 194.235(a).
8.3 Alternate Provisions for Pilots Trained in an Approved Training Program at the CH. Newly rated initial cadre instructors for an operator, a pilot school, or a training center (i.e., part 135 check pilots, part 141 chief instructors or assistant chief instructors, or part 142 TCEs who have been trained and certified at the manufacturer) will be proficient in the proposed training curriculum under their respective part because of their involvement in developing the proposed training program. This involvement will enable them to be in the best position to provide training to pilots enrolled in their respective CH’s training program under part 135, 141, or 142. The initial cadre of flight instructors will become fully qualified to serve in their designated function and receive a permanent LOA from the Administrator to subsequently conduct the training.
8.3 Alternate Provisions for Pilots Trained in an Approved Training… › 8.3.2 Instrument Training on the Areas of Operation Listed in §…
Because these pilots will now be authorized instructors (i.e., meet the requirements for instructors under their respective part), the pilots who will receive training under an approved training program do not require the same breadth of relief that instructor pilots, test pilots, and the initial cadre instructors need. Rather, the only relief necessary for pilots at an approved training program is that of flight simulation training device (FSTD) credit, and the cross-country relief in § 194.235 extended to all applicants. Also, § 194.243 allows for initial training toward part 61 pilot certificates not normally accomplished at a part 135 CH, which would require the trainer to hold a flight instructor certificate. See Chapter 11, Part 91K Requirements to Serve as a Powered-Lift Pilot in a Fractional Ownership Program, and Chapter 12, Requirements to Serve as a Powered-Lift Pilot Under Part 135, for additional information.
8.3.1 Use of Full Flight Simulator (FFS). As specified in § 194.231(c), an applicant may credit up to 4 hours obtained in a Level C or higher FFS toward the requirement to obtain 10 hours of cross-country time as PIC in a powered-lift if:
• The FFS represents the powered-lift category,
• The applicant was performing the duties of PIC, and
• The flight simulates a cross-country flight and includes the performance of instrument procedures under simulated instrument conditions.
8.3.2 Instrument Training on the Areas of Operation Listed in § 61.65(c). Pursuant to § 194.231(b), applicants who do not meet the cross-country aeronautical experience requirements specified in § 61.65(f)(2)(ii) may be considered eligible for an instrument rating if they complete the cross-country requirements listed in § 194.235, which may be completed with an authorized instructor. These requirements are detailed in Chapter 3.
Table 8-3. Alternate Provisions for an Instrument-Powered-Lift Rating: Persons Receiving
Training Under a Part 135, 141, or 142 Approved Training Program
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR PERSONS RECEIVING TRAINING
UNDER A PART 135, 141, OR 142 APPROVED TRAINING PROGRAM*
(herein referred to as applicants)
*To use the alternate provisions below, the applicant must receive training at an approved training program under part 135, 141, or 142 for the purpose of obtaining a powered-lift category rating.
Cross-Country Time as PIC
50 hours of cross-country time as PIC, of which 10 hours must have been in a powered-lift.
An applicant may credit up to 4 hours obtained in a Level C or higher FFS toward the requirement to obtain 10 hours of cross-country time as PIC in a powered-lift if:
(1) The FFS represents the powered-lift
category,
(2) The applicant was performing the
duties of PIC,
(3) The flight simulates a cross-country
flight and includes the performance of instrument procedures under simulated instrument conditions, and
(4) The flights are conducted in accordance
with an approved training program under part 135, 141, or 142.
Refer to § 194.231(c).
Instrument Time on the Areas of Operation Listed in § 61.65(c)
40 hours of actual or simulated instrument time in the areas of operation listed in § 61.65(c), of which 15 hours must have been received from an authorized instructor who holds an instrument-powered-lift rating, and the instrument time includes:
No alternative.
(1) 3 hours of instrument flight training
from an authorized instructor in a powered-lift that is appropriate to the instrument-powered-lift rating within 2 calendar months before the date of the practical test.
No alternative.
CURRENT FLIGHT TIME REQUIREMENTS
ALTERNATE PROVISIONS FOR PERSONS RECEIVING TRAINING
UNDER A PART 135, 141, OR 142 APPROVED TRAINING PROGRAM*
(herein referred to as applicants)
(2) Instrument flight training on cross-country
flight procedures, including one cross-country flight in a powered-lift with an authorized instructor that is performed under IFR, when a flight plan has been filed with an ATC facility, that involves:
• A flight of 250 NM along airways or by directed routing from an ATC facility;
• An instrument approach at each airport; and
• Three different kinds of approaches with the use of navigation systems.
Instead of completing one cross-country flight of 250 NM, an applicant may complete two cross-country flights, each of which must involve a flight of 100 NM along airways or by directed routing from an ATC facility.
Refer to §§ 194.231(b) and 194.235(a).
Continue reading ↓ 120 of 189 passages shown