Radar Vectors
Certification Standard Current Issued May 31, 2024 Flight Standards Service 71 pages Copy saved Nov 19, 2026

FAA-S-ACS-17 Airline Transport Pilot and Type Rating for Powered-Lift Category Airman Certification Standards

Official source ↗ Open PDF

Airline Transport Pilot and Type Rating for

Powered-Lift Category Airman Certification Standards

FAA-S-ACS-17

Flight Standards Service

Washington, DC 20591

November 2023

Airline Transport Pilot and Type Rating for Powered-Lift Category ACS (FAA-S-ACS-17) i

Foreword

The U.S. Department of Transportation, Federal Aviation Administration (FAA), Office of Safety Standards, Regulatory Support Division, Airman Testing Standards Branch, has published the Airline Transport Pilot (ATP) and Type Rating for Powered-Lift Category Airman Certification Standards (ACS) to communicate the aeronautical knowledge, risk management, and flight proficiency standards for ATP pilot and type rating certification in the powered-lift category.

This ACS is available for download, in PDF format, from www.faa.gov.

Comments regarding this ACS may be emailed to [email protected].

The FAA created FAA-G-ACS-2, Airman Certification Standards Companion Guide for Pilots, to provide guidance considered relevant and useful to the community. The number of appendices in the ACS was reduced and much of the non-regulatory material was moved to the Airman Certification Standards Companion Guide for Pilots. Applicants, instructors, and evaluators should consult this companion guide to familiarize themselves with ACS procedures. FAA-G-ACS-2 is available for download, in PDF format, from www.faa.gov.

ii Airline Transport Pilot and Type Rating for Powered-Lift Category ACS (FAA-S-ACS-17)

Table of Contents

Introduction

Airman Certification Standards Concept … 1 Use of the Term “Flight Manual” … 1

Area of Operation I. Preflight Preparation

Task A. Operation of Systems … 2 Task B. Performance and Limitations … 3 Task C. Weather Information (ATP) … 5 Task D. Human Factors (ATP) … 6 Task E. The Code of Federal Regulations (CFR) (ATP) … 7

Area of Operation II. Preflight Procedures

Task A. Preflight Assessment … 9 Task B. Powerplant Start … 10 Task C. Ground Taxiing … 11 Task D. Hover Taxi … 12 Task E. Air Taxi … 13 Task F. Before Takeoff Checks … 14 Task G. Flight Deck Management … 15

Area of Operation III. Takeoff and Departure Phase

Task A. Normal Takeoff and Climb from a Hover … 17 Task B. Rolling Takeoff and Climb … 18 Task C. Rejected Takeoff … 19 Task D. Maximum Performance Takeoff and Climb … 20

Area of Operation IV. In-flight Maneuvers

Task A. Steep Turns … 22 Task B. Specific Flight Characteristics … 23 Task C. Inflight Conversion During Straight-and-Level Flight … 23 Task D. Power-On Stall Prevention … 24 Task E. Power-Off Stall Prevention … 25

Area of Operation V. Instrument Procedures

Task A. Instrument Takeoff … 27

Task B. Departure Procedures … 28 Task C. Arrival Procedures … 29 Task D. Non-precision Approaches … 30 Task E. Precision Approaches … 31

iii

Table of Contents

Task F. Landing from a Precision Approach … 33 Task G. Circling Approach … 34 Task H. Missed Approach … 35 Task I. Holding Procedures … 36

Area of Operation VI. Landings and Approaches to Landings

Task A. Normal Approach and Landing … 38 Task B. Normal Approach to a Hover … 39 Task C. Steep Approach and Landing … 40 Task D. Running/Roll-On Landing … 41 Task E. Go-Around/Rejected Landing … 43

Area of Operation VII. Emergency Operations

Task A. Emergency Procedures … 44

Task B. Powerplant(s) Failure (Simulated) during Takeoff in Thrust-Borne Flight … 44 Task C. Powerplant(s) Failure (Simulated) during Takeoff While in Semi-Wing-Borne Flight … 45 Task D. Inflight Powerplant(s) Failure and Restart in Multi-Powerplant Aircraft … 46 Task E. Approach and Landing with Powerplant(s) Failure (Simulated) … 47 Task F. Precision Approach (Manually Flown) with Powerplant(s) Failure (Simulated) … 49 Task G. Recovery from Unusual Flight Attitudes … 50 Task H. Vortex Ring State (VRS) Avoidance … 51

Area of Operation VIII. Postflight Procedures

Task A. After Landing, Parking, and Securing … 52

Appendix 1: Practical Test Roles, Responsibilities, and Outcomes

Eligibility Requirements for an Airline Transport Pilot Certificate … 53 Use of the ACS During a Practical Test … 53 Instructor Responsibilities … 54 Evaluator Responsibilities … 54 Possible Outcomes of the Test … 55 Proficiency Check Requirements … 56 Addition of a VFR Only Type Rating … 57 Removal of a VFR Only Type Rating … 57

Appendix 2: Safety of Flight

General … 58 Stall, Spin, Angle of Attack Awareness … 58 Use of Checklists … 58 Positive Exchange of Flight Controls … 58 Use of Distractions … 58

iv

Table of Contents

Aeronautical Decision-Making, Risk Management, Crew Resource Management, and Single-Pilot

Resource Management … 58 Multi-Powerplant Considerations … 59

Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations

Aircraft Requirements & Limitations … 60 Equipment Requirements & Limitations … 60 Use of Flight Simulation Training Devices (FSTD) … 60 Credit for Pilot Time in an FSTD … 60 Use of Aviation Training Devices (ATD) … 60 Credit for Pilot Time in an ATD … 60 Operational Requirements, Limitations, & Task Information … 61

1 Airline Transport Pilot and Type Rating for Powered-Lift Category ACS (FAA-S-ACS-17)

Introduction › Airman Certification Standards Concept

Introduction

Airman Certification Standards Concept

The goal of the airman certification process is to ensure the applicant possesses the knowledge, ability to manage risks, and skill consistent with the privileges of the certificate or rating being exercised, in order to act as pilot-in-command (PIC).

Safe operations in today’s National Airspace System (NAS) require the integration of aeronautical knowledge, risk management, and flight proficiency standards. To accomplish these goals, the FAA drew upon the expertise of organizations and individuals across the aviation and training community to develop the ACS. The ACS integrates the elements of knowledge, risk management, and skill required for each airman certificate or rating. It thus forms a more comprehensive standard for what an applicant must know, consider, and do to demonstrate proficiency to pass the tests required for issuance of the applicable airman certificate or rating.

Introduction › Use of the Term “Flight Manual”

Use of the Term “Flight Manual”

Throughout this document, the term “flight manual” refers to the approved powered-lift aircraft flight manual.

Area of Operation I. Preflight Preparation

Area of Operation I. Preflight Preparation

Task A. Operation of Systems

References: AC 90-117, AC 91.21-1, AC 91-78, AC 120-76; FAA-H-8083-2, FAA-H-8083-25; FSB Report (type specific); Flight Manual

Area of Operation I. Preflight Preparation › Task A. Operation of Systems

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with aircraft systems and their components; and their normal, abnormal, and emergency procedures.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.I.A.K1 Landing gear–extension/retraction system(s), indicators, brakes, antiskid, tires, nose-wheel steering, and shock absorbers.

AP.I.A.K2 Powerplant(s)–controls, indications, and systems, as applicable.

AP.I.A.K3 Thrust components–transmission, drive shafts, gear boxes, oil/fluid levels, tolerances, electronic controls, motors, ducts, and limitations as applicable.

AP.I.A.K4 Fuel system–capacity, drains, pumps, controls, indicators, cross-feeding, transferring, jettison, fuel grade, color and additives, fueling and defueling procedures, and fuel substitutions (if applicable).

AP.I.A.K5 Battery(s) used for propulsion–charging, discharging, and condition, as applicable.

AP.I.A.K6 Oil system–capacity, allowable types of oil, quantities, and indicators.

AP.I.A.K7 Hydraulic system–capacity, pumps, pressure, reservoirs, allowable types of fluid, and regulators.

AP.I.A.K8 Electrical system–alternators, generators, batteries, circuit breakers and protection devices, controls, indicators, and external and auxiliary power sources and ratings.

AP.I.A.K9 Pneumatic and environmental systems–heating, cooling, ventilation, oxygen, pressurization, supply for ice protection systems, controls, indicators, and regulating devices.

AP.I.A.K10 Avionics and communications–autopilot, flight director, Electronic Flight Instrument Systems (EFIS), Flight Management System (FMS), Electronic Flight Bag (EFB), Radar, Inertial Navigation Systems (INS), Global Navigation Satellite System (GNSS), Space-Based Augmentation System (SBAS), Ground-Based Augmentation System (GBAS), ground-based navigation systems and components, Automatic Dependent Surveillance – Broadcast (ADS-B) In and Out, Automatic Dependent Surveillance – Contract (ADS-C), traffic awareness/warning/avoidance systems, terrain awareness/ warning/alert systems, communication systems (e.g., data link, Ultra High Frequency (UHF)/Very High Frequency (VHF)/High Frequency (HF), satellite), Controller Pilot Data Link Communication (CPDLC), indicating devices, transponder, and emergency locator transmitter, Head Up-Display (HUD).

AP.I.A.K11 Ice protection–anti-ice, deice, pitot-static system protection, turbine inlet, windshield, airfoil surfaces, and other related components.

AP.I.A.K12 Crewmember and passenger equipment–oxygen system, survival gear, emergency exits, evacuation procedures and crew duties, quick donning oxygen mask for crewmembers, passenger oxygen system.

AP.I.A.K13 Flight controls appropriate for the aircraft provided for the practical test.

AP.I.A.K14 Pitot-static system–associated instruments and the power source for those flight instruments. Operation and power sources for other flight instruments.

Area of Operation I. Preflight Preparation

AP.I.A.K15 Fire & smoke detection, protection, and suppression–powerplant, cargo and passenger compartments, lavatory, pneumatic and environmental, electrical/avionics, and batteries (on aircraft and personal electronic devices).

AP.I.A.K16 Envelope protection–angle of attack warning and protection, and speed protection.

AP.I.A.K17 Flight manual as it relates to the systems and components in the aircraft.

AP.I.A.K18 How to use a Minimum Equipment List (MEL) and a Configuration Deviation List (CDL).

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.I.A.R1 Detection of system malfunctions or failures.

AP.I.A.R2 Management of a system failure.

AP.I.A.R3 Monitoring and management of automated systems, if applicable.

AP.I.A.R4 Following checklists or procedures.

Skills: The applicant exhibits the skill to:

AP.I.A.S1 Explain and describe the operation of the aircraft systems and components using correct terminology.

AP.I.A.S2 Recall immediate action items or memory items, if appropriate.

AP.I.A.S3 Identify system or component limitations listed in the flight manual.

AP.I.A.S4 Demonstrate or describe, as appropriate, the process for deferring inoperative equipment (e.g., MEL) and using a CDL.

AP.I.A.S5 Comply with operations specifications, management specifications, and letters of authorization, if applicable.

AP.I.A.S6 Through the use of the appropriate checklists and normal and abnormal procedures, demonstrate the proper use of the aircraft systems, subsystems, and devices, as determined by the evaluator.

Area of Operation I. Preflight Preparation › Task B. Performance and Limitations

Task B. Performance and Limitations

References: 14 CFR part 91; AC 20-117, AC 91-74, AC 120-27, AC 135-17; AIM; Chart Supplements; FAA-H-8083-1, FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine that the applicant exhibits satisfactory knowledge, risk management, and skills associated with operating an aircraft safely within its operating envelope.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.I.B.K1 Elements related to performance and limitations by explaining the use of charts, tables, and data to determine performance.

AP.I.B.K2 How to determine the following:

AP.I.B.K2a a. Aircraft performance in selected phase(s) of flight

AP.I.B.K2b b. Performance with a powerplant inoperative in selected phase(s) of flight

Area of Operation I. Preflight Preparation

AP.I.B.K2c c. Weight and balance and how to shift weight

AP.I.B.K2d d. Other performance data as appropriate to the aircraft

AP.I.B.K3 Factors affecting performance, including:

AP.I.B.K3a a. Atmospheric conditions

AP.I.B.K3b b. Pilot technique

AP.I.B.K3c c. Airport environment (e.g., runway condition, land and hold short operations (LAHSO))

AP.I.B.K3d d. Aircraft configuration

AP.I.B.K3e e. Loading [e.g., center of gravity (CG)]

AP.I.B.K3f f. Weight and balance

AP.I.B.K4 Aerodynamics and how it relates to performance.

AP.I.B.K5 Adverse effects of exceeding an aircraft limitation or the aircraft operating envelope.

AP.I.B.K6 Clean wing concept; deicing and anti-icing procedures, including use of appropriate deice fluid, holdover tables, calculating hold-over times, and pre-takeoff contamination checks.

AP.I.B.K7 Relationship between Mach number, indicated airspeed, true airspeed, and change over altitudes.

AP.I.B.K8 Best range and endurance speed.

AP.I.B.K9 Height/Velocity (H/V) diagram according to the flight manual.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.I.B.R1 Use of performance charts, tables, and data.

AP.I.B.R2 Aircraft limitations.

AP.I.B.R3 Possible differences between calculated performance and actual performance.

AP.I.B.R4 Aircraft icing and its effect on performance and stall warning.

AP.I.B.R5 Operating with reduced power margins.

Skills: The applicant exhibits the skill to:

AP.I.B.S1 Describe the airspeeds and configurations used during specific phases of flight.

AP.I.B.S2 Describe the effects of meteorological conditions on performance for all phases of flight and correctly apply these factors to a specific chart, table, graph, or other performance data.

AP.I.B.S3 Describe the procedures for surface (wing, rotor,etc.) contamination recognition and any deice/anti-ice procedures prior to takeoff.

AP.I.B.S4 Explain the adverse effects of airframe icing during all phases of flight. Describe any operating limitations for flight in icing conditions. If equipped, describe the procedures for deicing and anti-icing system use and their effects on performance.

AP.I.B.S5 Compute weight and balance, including practical techniques to resolve out-of-limits calculations for a representative scenario, as specified by the evaluator.

AP.I.B.S6 Determine the computed center of gravity is within the acceptable limits and the lateral fuel balance is within limits for takeoff and landing.

Area of Operation I. Preflight Preparation

AP.I.B.S7 Demonstrate proficient use of appropriate performance charts, tables, graphs, or other means to determine aircraft performance and limitations for all phases of flight.

Area of Operation I. Preflight Preparation › Task C. Weather Information (ATP)

Task C. Weather Information (ATP)

References: 14 CFR part 91; AC 91-74 AC 91-92; AIM; FAA-H-8083-2, FAA-H-8083-16, FAA-H-8083-25, FAA-H-8083-28

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with obtaining, understanding, and applying weather information for a flight under IFR.

Note: If K2 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.

Note: If K3 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.

Note: See Appendix 1: Practical Test Roles, Responsibilities, and Outcomes and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.I.C.K1 Sources of weather data (e.g., National Weather Service, Flight Service) for flight planning purposes.

AP.I.C.K2 Acceptable weather products and resources required for preflight planning, current and forecast weather for departure, en route, and arrival phases of flight such as:

AP.I.C.K2a a. Airport Observations (METAR and SPECI) and Pilot Observations (PIREP)

AP.I.C.K2b b. Surface Analysis Chart, Ceiling and Visibility Chart (CVA)

AP.I.C.K2c c. Terminal Aerodrome Forecasts (TAF)

AP.I.C.K2d d. Graphical Forecasts for Aviation (GFA)

AP.I.C.K2e e. Wind and Temperature Aloft Forecast (FB)

AP.I.C.K2f f. Convective Outlook (AC)

AP.I.C.K2g g. Inflight Aviation Weather Advisories including Airmen's Meteorological Information (AIRMET),

Significant Meteorological Information (SIGMET), and Convective SIGMET

AP.I.C.K3 Meteorology applicable to the departure, en route, alternate, and destination for flights conducted under Instrument Flight Rules (IFR) to include expected climate and hazardous conditions such as:

AP.I.C.K3a a. Atmospheric composition and stability

AP.I.C.K3b b. Wind (e.g., windshear, mountain wave, factors affecting wind, etc.)

AP.I.C.K3c c. Temperature and heat exchange

AP.I.C.K3d d. Moisture/precipitation

AP.I.C.K3e e. Weather system formation, including air masses and fronts

AP.I.C.K3f f. Clouds

AP.I.C.K3g g. Turbulence

AP.I.C.K3h h. Thunderstorms and microbursts

AP.I.C.K3i i. Icing and freezing level information

AP.I.C.K3j j. Fog/mist

Area of Operation I. Preflight Preparation

AP.I.C.K3k k. Frost

AP.I.C.K3l l. Obstructions to visibility (e.g., smoke, haze, volcanic ash, etc.)

AP.I.C.K4 Flight deck displays of digital weather and aeronautical information, their use to navigate around weather, and equipment limitations.

AP.I.C.K5 Low-visibility operations (e.g., surface movement, category II and III approaches). (ATP)(AMEL, AMES).

AP.I.C.K6 Flight Risk Assessment Tools.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.I.C.R1 Weather conditions involved in departure and in-flight decision making, to include:

AP.I.C.R1a a. Circumstances requiring a change in course or destination

AP.I.C.R1b b. Known or forecast icing, winds or turbulence aloft, volcanic ash, destination weather, etc.

AP.I.C.R1c c. Personal weather minimums

AP.I.C.R1d d. Operator specified or aircraft operational limitations, if applicable

AP.I.C.R2 Use and limitations of:

AP.I.C.R2a a. Installed onboard weather equipment

AP.I.C.R2b b. Aviation weather reports and forecasts

AP.I.C.R2c c. Inflight weather resources

Skills: The applicant exhibits the skill to:

AP.I.C.S1 Interpret weather information, apply principles of aeronautical decision-making, and use a Flight Risk Assessment Tool, if available.

Area of Operation I. Preflight Preparation › Task D. Human Factors (ATP)

Task D. Human Factors (ATP)

References: 14 CFR part 91; AC 120-100, AC 120-51; AIM; FAA-H-8083-2, FAA-H-8083-25

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with personal health, flight physiology, and aeromedical and human factors related to safety of flight.

Note: If K1 is selected, the evaluator must assess the applicant's knowledge of at least three sub-elements.

Note: See Appendix 1: Practical Test Roles, Responsibilities, and Outcomes and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.I.D.K1 Causes, effects, recognition, and corrective actions associated with aeromedical and physiological issues, including:

AP.I.D.K1a a. Hypoxia

AP.I.D.K1b b. Hyperventilation

AP.I.D.K1c c. Middle ear and sinus problems

Area of Operation I. Preflight Preparation

AP.I.D.K1d d. Spatial disorientation

AP.I.D.K1e e. Motion sickness

AP.I.D.K1f f. Carbon monoxide poisoning

AP.I.D.K1g g. Stress

AP.I.D.K1h h. Fatigue

AP.I.D.K1i i. Dehydration and nutrition

AP.I.D.K1j j. Hypothermia

AP.I.D.K1k k. Optical illusions

AP.I.D.K1l l. Dissolved nitrogen in the bloodstream after scuba dives

AP.I.D.K2 Effects of alcohol, drugs, and over-the-counter medications.

AP.I.D.K3 Aeronautical Decision-Making (ADM) to include using Crew Resource Management (CRM) or Single- Pilot Resource Management (SRM), as appropriate.

AP.I.D.K4 Components of self-assessment for determining fitness for flight.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.I.D.R1 Aeromedical and physiological issues.

AP.I.D.R2 Hazardous attitudes.

AP.I.D.R3 Distractions, task prioritization, loss of situational awareness, or disorientation.

AP.I.D.R4 Confirmation and expectation bias.

Skills: The applicant exhibits the skill to:

AP.I.D.S1 Perform a self-assessment and determine fitness for flight.

Area of Operation I. Preflight Preparation › Task E. The Code of Federal Regulations (CFR) (ATP)

Task E. The Code of Federal Regulations (CFR) (ATP)

References: 14 CFR parts 61, 91, 135; 49 CFR part 830; FAA-H-8083-2, FAA-H-8083-25

Objective: To determine the applicant exhibits satisfactory knowledge associated with regulations applicable to the privileges and limitations of the ATP certificate and to flight operations that require an ATP certificate.

Note: See Appendix 1: Practical Test Roles, Responsibilities, and Outcomes and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.I.E.K1 14 CFR part 61 subparts A, B, G.

AP.I.E.K2 14 CFR part 91 subparts A, B, C, F, G, H.

AP.I.E.K3 14 CFR part 135 subparts A, B, C, D, E, F, G.

AP.I.E.K4 49 CFR part 830.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

Area of Operation I. Preflight Preparation

AP.I.E.R1 Lack of compliance with the applicable CFRs.

Skills: The applicant exhibits the skill to:

AP.I.E.S1 Apply the CFRs to the flight and operation.

Area of Operation II. Preflight Procedures › Task A. Preflight Assessment

Area of Operation II. Preflight Procedures

Area of Operation II. Preflight Procedures

Task A. Preflight Assessment

References: 14 CFR parts 43, 61, 71, 91, 97, 119, 135; AC 120-27, AC 135-17; AIM; FAA-H-8083-2, FAA-H-8083-25, FAA-H-8083-28; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with preparation for safe flight.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.II.A.K1 Pilot self-assessment.

AP.II.A.K2 Determining that the aircraft to be used is appropriate, airworthy, and in a condition for safe flight by locating and explaining related documents such as:

AP.II.A.K2a a. Airworthiness and registration certificates

AP.II.A.K2b b. Operating limitations, handbooks, and manuals

AP.II.A.K2c c. Minimum Equipment List (MEL) and Configuration Deviation List (CDL), Kinds of Operations

Equipment Lists (KOEL)

AP.II.A.K2d d. Weight and balance data

AP.II.A.K2e e. Required inspections or tests and appropriate records and documentation (e.g., dispatch

release) as applicable to the proposed flight or operation

AP.II.A.K3 Preventive maintenance that can be performed by the pilot or other designated crewmember.

AP.II.A.K4 Aircraft preflight inspection, including:

AP.II.A.K4a a. Which items should be inspected

AP.II.A.K4b b. The reasons for checking each item

AP.II.A.K4c c. How to detect possible defects

AP.II.A.K4d d. The associated regulations

AP.II.A.K5 Environmental factors, including weather, terrain, route selection, and obstructions.

AP.II.A.K6 Requirements for current and appropriate navigation data.

AP.II.A.K7 Operations specifications, management specifications, or letters of authorization applying to a particular aircraft and operation, if applicable.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.II.A.R1 Human performance factors.

AP.II.A.R2 Inoperative equipment discovered prior to flight.

AP.II.A.R3 Environment (e.g., weather, airports, airspace, terrain, obstacles).

AP.II.A.R4 External pressures.

AP.II.A.R5 Aviation security concerns.

Area of Operation II. Preflight Procedures

Skills: The applicant exhibits the skill to:

AP.II.A.S1 Inspect the aircraft in accordance with an appropriate checklist demonstrating proper operation of applicable aircraft systems. Coordinate checklist with crew, if appropriate.

AP.II.A.S2 Coordinate with ground crew and ensure adequate clearance prior to moving doors, hatches, flight control surfaces, etc.

AP.II.A.S3 Document any discrepancies found; take corrective action and acknowledge limitations imposed by MEL/CDL items, if applicable.

AP.II.A.S4 Determine if the aircraft is airworthy and in condition for safe flight.

AP.II.A.S5 Identify and comply with operations specifications as required.

AP.II.A.S6 Assess factors related to the environment (weather, airports, terrain, airspace).

AP.II.A.S7 Ensure the aircraft and surfaces are free of ice, snow, and frost. If icing conditions are present, demonstrate satisfactory knowledge of deicing procedures.

AP.II.A.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation II. Preflight Procedures › Task B. Powerplant Start

Task B. Powerplant Start

References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with powerplant start procedures.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.II.B.K1 Normal and abnormal powerplant start procedures and limitations, including the use of an auxiliary power unit (APU) or external power source, if applicable.

AP.II.B.K2 Starting under various conditions.

AP.II.B.K3 Malfunctions during powerplant start, procedures to address the malfunction, and any associated limitations.

AP.II.B.K4 Coordinating and communicating with ground personnel for powerplant start, if applicable.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.II.B.R1 Malfunctions during powerplant start.

AP.II.B.R2 External or internal power starts.

AP.II.B.R3 Thrust device, rotor, exhaust, and powerplant safety, as applicable.

AP.II.B.R4 Hazards, including downwash, personnel, vehicles, vessels, foreign object debris, and other aircraft in the vicinity during powerplant start.

AP.II.B.R5 Managing situations where specific instructions or checklist items are not published.

Skills: The applicant exhibits the skill to:

Area of Operation II. Preflight Procedures

AP.II.B.S1 Ensure the ground safety procedures are followed during the before-start, start, and after-start phases.

AP.II.B.S2 Use appropriate ground crew personnel during the start procedures (if applicable).

AP.II.B.S3 Coordinate with crew, if applicable, and complete the appropriate checklist(s) prior to and after powerplant start.

AP.II.B.S4 Respond appropriately to an abnormal start or malfunction.

Area of Operation II. Preflight Procedures › Task C. Ground Taxiing

Task C. Ground Taxiing

References: 14 CFR part 91, 135; AC 91-73, 120-74; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; NOTAMs; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with safe taxi operations.

Knowledge: The applicant demonstrates understanding of:

AP.II.C.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).

AP.II.C.K2 Taxi instructions/clearances, including published taxi routes.

AP.II.C.K3 Airport/heliport/helipad/landing area, signs, markings, and lighting.

AP.II.C.K4 Appropriate aircraft lighting for day and night operations.

AP.II.C.K5 Appropriate aircraft configuration.

AP.II.C.K6 Communications at towered and nontowered airports.

AP.II.C.K7 Appropriate flight deck activities prior to taxi, including route planning, identifying the location of Hot Spots, and coordinating with crew if, applicable.

AP.II.C.K8 Entering or crossing runways.

AP.II.C.K9 Night taxi operations.

AP.II.C.K10 Low visibility taxi operations and techniques used to avoid disorientation.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.II.C.R1 Distractions, task prioritization, loss of situational awareness, or disorientation.

AP.II.C.R2 Confirmation or expectation bias as related to taxi instructions.

AP.II.C.R3 A taxi route or departure runway change.

AP.II.C.R4 Use of checklists or procedures.

AP.II.C.R5 Low visibility taxi operations.

AP.II.C.R6 Runway incursion.

Skills: The applicant exhibits the skill to:

AP.II.C.S1 Receive/record taxi instructions, read back/acknowledge taxi clearances, and review taxi routes on the airport diagram.

Area of Operation II. Preflight Procedures

AP.II.C.S2 Use an appropriate airport/heliport diagram or taxi chart, if published.

AP.II.C.S3 Comply with air traffic control (ATC) clearances and instructions and observe all runway hold lines, Instrument Landing System (ILS) critical areas, beacons, and other airport/taxiway markings and lighting.

AP.II.C.S4 Coordinate with crew, if applicable, and complete the appropriate checklist(s) prior to and during taxi, as appropriate.

AP.II.C.S5 Maintain situational awareness.

AP.II.C.S6 Use appropriate thrust and maintain correct and positive aircraft control, proper speed, and appropriate separation between other aircraft, vehicles, and persons to avoid an incursion/incident/ accident.

AP.II.C.S7 Demonstrate taxi during day and night operations. If either condition is not available, the applicant explains the differences between day and night taxi.

AP.II.C.S8 Demonstrate proper use of aircraft exterior lighting for day and night operations. If either condition is not available, the applicant explains the differences between exterior aircraft lighting used for day and night operations.

AP.II.C.S9 Explain the hazards of low visibility taxi operations.

Area of Operation II. Preflight Procedures › Task D. Hover Taxi

Task D. Hover Taxi

References: AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with hover taxi operations, including runway incursion avoidance.

Knowledge: The applicant demonstrates understanding of:

AP.II.D.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).

AP.II.D.K2 Hover taxi instructions, clearances, and limitations.

AP.II.D.K3 Airport, heliport, helipad, or unprepared surface environment.

AP.II.D.K4 Visual indicators for wind.

AP.II.D.K5 Aircraft lighting, as appropriate.

AP.II.D.K6 Procedures for.

AP.II.D.K6a a. Appropriate flight deck activities during taxiing

AP.II.D.K6b b. Safe hover taxi at towered and non-towered airports/heliports/helipads/landing areas

AP.II.D.K6c c. Entering or crossing runways

AP.II.D.K7 Aircraft configuration.

AP.II.D.K8 Aircraft operating limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.II.D.R1 Distractions, task prioritization, loss of situational awareness, or disorientation.

Area of Operation II. Preflight Procedures

AP.II.D.R2 Low visibility hover taxi operations.

AP.II.D.R3 Powerplant(s) failure during hover taxi.

AP.II.D.R4 Other aircraft and hazards.

AP.II.D.R5 Hazardous effects of downwash.

AP.II.D.R6 Aircraft configuration.

AP.II.D.R7 Height/Velocity (H/V) considerations.

AP.II.D.R8 Crosswind limitations.

AP.II.D.R9 Confirmation or expectation bias as related to taxi instructions.

AP.II.D.R10 Runway incursion.

AP.II.D.R11 Other hazards specific to the powered-lift make and model.

Skills: The applicant exhibits the skill to:

AP.II.D.S1 Complete the appropriate checklist(s).

AP.II.D.S2 Receive and correctly read back clearances/instructions, if applicable.

AP.II.D.S3 Use an airport diagram or taxi chart during taxi, if published, and maintain situational awareness.

AP.II.D.S4 Comply with airport/heliport taxiway markings, signals, and signs.

AP.II.D.S5 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.

AP.II.D.S6 Hover taxi over specified ground references, demonstrating forward, sideward, and rearward hovering and hovering turns.

AP.II.D.S7 Maintain recommended hovering altitude, ±1/2 of that altitude within 10 feet of the surface, if above 10 feet, ±5 feet.

AP.II.D.S8 Demonstrate the maneuver in crosswind conditions on specified headings.

Area of Operation II. Preflight Procedures › Task E. Air Taxi

Task E. Air Taxi

References: AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with air taxi operations.

Knowledge: The applicant demonstrates understanding of:

AP.II.E.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).

AP.II.E.K2 Air taxi instructions, clearances, and limitations.

AP.II.E.K3 Aircraft configuration.

AP.II.E.K4 Airport, heliport, helipad, or unprepared surface environment.

AP.II.E.K5 Visual indicators for wind.

Area of Operation II. Preflight Procedures

AP.II.E.K6 Aircraft lighting, as appropriate.

AP.II.E.K7 Procedures for:

AP.II.E.K7a a. Appropriate flight deck activities during taxiing

AP.II.E.K7b b. Safe air taxi at towered and non-towered airports/heliports/helipads/landing areas

AP.II.E.K7c c. Overflying of runways

AP.II.E.K8 Aircraft operating limitations.

AP.II.E.K9 Appropriate height and speed for air taxi.

AP.II.E.K10 Height/Velocity (H/V) considerations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.II.E.R1 Activities and distractions.

AP.II.E.R2 Reduced visibility or night taxi operations.

AP.II.E.R3 H/V diagram performance in case of powerplant failure.

AP.II.E.R4 Other aircraft and hazards.

AP.II.E.R5 Runway incursion.

Skills: The applicant exhibits the skill to:

AP.II.E.S1 Complete the appropriate checklist(s).

AP.II.E.S2 Use an airport diagram or taxi chart during taxi, if published, and maintain situational awareness.

AP.II.E.S3 Select a safe airspeed and altitude.

AP.II.E.S4 Maintain specified altitude, ±10 feet.

AP.II.E.S5 Maintain a designated airspeed, ±10 knots, taxi height, ±10 feet, and flight path.

AP.II.E.S6 Air taxi from one point to another under various wind conditions.

AP.II.E.S7 Maintain the aircraft within operating limits throughout the maneuver.

AP.II.E.S8 Comply with airport/heliport/helipad/landing area markings, lights, signs, and ATC instructions.

AP.II.E.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation II. Preflight Procedures › Task F. Before Takeoff Checks

Task F. Before Takeoff Checks

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with before takeoff checks.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

Area of Operation II. Preflight Procedures

AP.II.F.K1 Purpose of before takeoff checklist items, including:

AP.II.F.K1a a. Reasons for checking each item

AP.II.F.K1b b. Detecting malfunctions

AP.II.F.K1c c. Ensuring the aircraft is in safe operating condition

AP.II.F.K2 Deicing and anti-icing procedures, holdover times, and pre-takeoff contamination check.

AP.II.F.K3 Adverse weather considerations for performance on takeoff (e.g., snow, ice, gusting crosswinds, lowvisibility).

AP.II.F.K4 Items to be included in a before takeoff briefing.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.II.F.R1 Division of attention while conducting before takeoff checks.

AP.II.F.R2 An unexpected change in the runway to be used for departure.

AP.II.F.R3 Using performance data to set airspeeds and flight instruments for actual conditions and the departure runway.

AP.II.F.R4 Setting navigation and communication equipment for departure.

AP.II.F.R5 Configuring autopilot and flight director for departure.

AP.II.F.R6 Adverse weather conditions prior to takeoff (e.g., snow, ice, gusting crosswinds, low-visibility).

AP.II.F.R7 Potential powerplant failure during takeoff or other malfunction considering operational factors such as aircraft characteristics, runway/takeoff path length, surface.

Skills: The applicant exhibits the skill to:

AP.II.F.S1 Determine the aircraft's takeoff performance and set configuration for the planned departure.

AP.II.F.S2 Coordinate with crew, if applicable, and complete the appropriate checklist(s) prior to takeoff in a timely manner.

AP.II.F.S3 Determine all systems checked are within an acceptable operating range and are safe for the proposed flight. During the checks, explain at the request of the evaluator, any system operating characteristic or limitation and any corrective action for a malfunction.

AP.II.F.S4 Determine airspeeds/V-speeds and set flight instruments appropriately, configure flight director, autopilot, and navigation and communication equipment for the current flight conditions and takeoff and departure clearances.

AP.II.F.S5 Conduct a briefing that includes procedures for emergency and abnormal situations (e.g., powerplant failure, windshear), which may be encountered during takeoff, and state the planned action if they were to occur.

AP.II.F.S6 Obtain and correctly interpret the takeoff and departure clearance.

Area of Operation II. Preflight Procedures › Task G. Flight Deck Management

Task G. Flight Deck Management

References: 14 CFR part 91; AC 120-71; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight deck management practices.

Area of Operation II. Preflight Procedures

Note: See Appendix 2: Safety of Flight.

Knowledge: The applicant demonstrates understanding of:

AP.II.G.K1 Passenger briefing requirements, including operation and required use of safety restraint systems.

AP.II.G.K2 Use of appropriate checklists.

AP.II.G.K3 Requirements for current and appropriate navigation data.

AP.II.G.K4 Securing items and cargo.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.II.G.R1 Use of systems or equipment, including automation and portable electronic devices.

AP.II.G.R2 Inoperative equipment.

AP.II.G.R3 Passenger distractions.

Skills: The applicant exhibits the skill to:

AP.II.G.S1 Secure all items in the aircraft.

AP.II.G.S2 Conduct an appropriate passenger briefing, including identifying the pilot-in-command (PIC), use of safety belts, shoulder harnesses, doors, sterile aircraft, passenger conduct and avoidance of rotor or air induction systems, powerplants, and other heat sources, and emergency procedures.

AP.II.G.S3 Properly program and manage the aircraft’s automation, as applicable.

AP.II.G.S4 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation III. Takeoff and Departure Phase › Task A. Normal Takeoff and Climb from a Hover

Area of Operation III. Takeoff and Departure Phase

Area of Operation III. Takeoff and Departure Phase

Note: Select all applicable tasks in accordance with the aircraft's operating characteristics as specified in the flight manual.

Task A. Normal Takeoff and Climb from a Hover

References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal takeoff and climb from a hover.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.

Knowledge: The applicant demonstrates understanding of:

AP.III.A.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.

AP.III.A.K2 Recommended takeoff and climb profiles.

AP.III.A.K3 Aircraft configuration.

AP.III.A.K4 Factors affecting the profile of the height/velocity (H/V) diagram.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.III.A.R1 Selection of helipad/deck, runway, or departure point based on aircraft performance and limitations, available distance, and wind.

AP.III.A.R2 Effects of:

AP.III.A.R2a a. Crosswind

AP.III.A.R2b b. Windshear

AP.III.A.R2c c. Tailwind

AP.III.A.R2d d. Wake turbulence

AP.III.A.R2e e. Runway/departure point surface/condition

AP.III.A.R2f f. Aircraft weight

AP.III.A.R3 Abnormal operations including:

AP.III.A.R3a a. Rejected takeoff

AP.III.A.R3b b. Powerplant failure in hover/takeoff/climb phase of flight

AP.III.A.R4 Collision hazards.

AP.III.A.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

AP.III.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

Area of Operation III. Takeoff and Departure Phase

AP.III.A.S1 Complete the appropriate checklist(s).

AP.III.A.S2 Make radio calls as appropriate.

AP.III.A.S3 Verify assigned/correct runway, if at an airport.

AP.III.A.S4 Determine wind direction with or without visible wind direction indicators.

AP.III.A.S5 Position the flight controls and configure the aircraft for the existing wind conditions.

AP.III.A.S6 Clear the area, ground or hover taxi into takeoff position, and hover the aircraft above the departure point, aligned with the departure path.

AP.III.A.S7 Confirm takeoff power and instrument indications prior to forward movement.

AP.III.A.S8 Takeoff and accelerate to the manufacturer’s recommended speed.

AP.III.A.S9 After takeoff, establish and maintain a positive rate of climb and configure aircraft, as appropriate.

AP.III.A.S10 Maintain the aircraft within operating limits throughout the maneuver.

AP.III.A.S11 Maintain VY ±5 knots to a safe maneuvering altitude.

AP.III.A.S12 Maintain directional control and proper wind-drift correction throughout takeoff and climb.

AP.III.A.S13 Comply with noise abatement procedures, as applicable.

AP.III.A.S14 Use runway incursion avoidance procedures, if applicable.

Area of Operation III. Takeoff and Departure Phase › Task B. Rolling Takeoff and Climb

Task B. Rolling Takeoff and Climb

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with rolling takeoff with wheel-type landing gear.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.

Knowledge: The applicant demonstrates understanding of:

AP.III.B.K1 Effects of atmospheric conditions, including wind, temperature and altitude, on takeoff and climb performance and the H/V diagram.

AP.III.B.K2 Aircraft performance and limitations.

AP.III.B.K3 Appropriate aircraft configuration and power setting for takeoff and climb.

AP.III.B.K4 Translational lift.

AP.III.B.K5 Runway markings and lighting.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.III.B.R1 Selection of a runway, or runway intersection, aircraft limitations, available distance, surface conditions, wind, and takeoff and landing distance.

Area of Operation III. Takeoff and Departure Phase

AP.III.B.R2 Effects of.

AP.III.B.R2a a. Crosswind

AP.III.B.R2b b. Windshear

AP.III.B.R2c c. Tailwind

AP.III.B.R2d d. Wake turbulence

AP.III.B.R2e e. Runway/departure point surface/condition

AP.III.B.R2f f. Aircraft weight

AP.III.B.R3 Abnormal operations, including planning for:

AP.III.B.R3a a. Rejected takeoff

AP.III.B.R3b b. Powerplant failure in takeoff/climb phase of flight

AP.III.B.R4 Aircraft configuration.

AP.III.B.R5 Collision hazards.

AP.III.B.R6 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

AP.III.B.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.III.B.S1 Complete the appropriate checklist(s).

AP.III.B.S2 Make radio calls as appropriate.

AP.III.B.S3 Verify assigned/correct runway or takeoff path.

AP.III.B.S4 Configure the aircraft correctly for takeoff, regarding environmental conditions and aircraft loading.

AP.III.B.S5 Position the flight controls for the existing wind, if applicable.

AP.III.B.S6 Clear the area, taxi into takeoff position, and align the aircraft on the runway centerline or takeoff path.

AP.III.B.S7 Maintain centerline and coordinated flight control inputs during the takeoff roll.

AP.III.B.S8 Confirm takeoff power, proper powerplant(s), and flight instrument indications prior to lift-off.

AP.III.B.S9 Lift off at the recommended airspeed and make callouts as appropriate.

AP.III.B.S10 Transition to recommended climb airspeed ±5 knots.

AP.III.B.S11 Maintain flight path and continue climb to the appropriate altitude at the recommended airspeed and configuration.

AP.III.B.S12 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation III. Takeoff and Departure Phase › Task C. Rejected Takeoff

Task C. Rejected Takeoff

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a rejected takeoff.

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements &

Area of Operation III. Takeoff and Departure Phase

Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.III.C.K1 Conditions and situations that could warrant a rejected takeoff (e.g., takeoff warning systems, powerplant failure, other systems warning/failure).

AP.III.C.K2 Techniques and procedure for accomplishing a rejected takeoff.

AP.III.C.K3 Safety considerations following a rejected takeoff.

AP.III.C.K4 Performance data and the height velocity (H/V) diagram.

AP.III.C.K5 Relevant V-speeds for a rejected takeoff.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.III.C.R1 Selection of the takeoff path based on aircraft limitations, available distance, surface conditions, and wind.

AP.III.C.R2 A powerplant failure or other malfunction during takeoff.

AP.III.C.R3 Directional control following a rejected takeoff.

AP.III.C.R4 A rejected takeoff with inadequate stopping distance.

AP.III.C.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.III.C.S1 Conduct a rejected takeoff based on the scenario presented by the evaluator.

AP.III.C.S2 Safely stop the aircraft.

AP.III.C.S3 Maintain positive aircraft control throughout the maneuver.

AP.III.C.S4 Coordinate with crew, if applicable, and complete the appropriate procedures, checklist(s), and radio calls following a rejected takeoff in a timely manner.

Area of Operation III. Takeoff and Departure Phase › Task D. Maximum Performance Takeoff and Climb

Task D. Maximum Performance Takeoff and Climb

References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with maximum performance takeoff and climb.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.III.D.K1 Situations where this maneuver is appropriate.

AP.III.D.K2 Effects of atmospheric conditions, including wind and temperature, on takeoff and climb performance.

AP.III.D.K3 Appropriate aircraft configuration, takeoff, and climb profiles.

AP.III.D.K4 Factors affecting the profile of the height/velocity (H/V) diagram.

Area of Operation III. Takeoff and Departure Phase

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.III.D.R1 Selection of takeoff path based on aircraft performance and limitations, available distance, and wind.

AP.III.D.R2 Effects of:

AP.III.D.R2a a. Crosswind

AP.III.D.R2b b. Windshear

AP.III.D.R2c c. Tailwind

AP.III.D.R2d d. Low level turbulence

AP.III.D.R2e e. Surface conditions

AP.III.D.R3 Abnormal operations including:

AP.III.D.R3a a. Rejected takeoff

AP.III.D.R3b b. Powerplant failure in takeoff/climb phase of flight

AP.III.D.R4 Collision hazards.

AP.III.D.R5 Low altitude maneuvering, including controlled flight into terrain (CFIT).

AP.III.D.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.III.D.S1 Complete the appropriate checklist(s).

AP.III.D.S2 Make radio calls as appropriate.

AP.III.D.S3 Determine wind direction with or without visible wind direction indicators.

AP.III.D.S4 Position the flight controls and configure the aircraft for the existing wind conditions.

AP.III.D.S5 Clear the area, taxi into takeoff position, utilizing maximum available takeoff area and align the aircraft on the takeoff path.

AP.III.D.S6 Confirm takeoff power and proper powerplant and flight instrument indications prior to takeoff.

AP.III.D.S7 Establish and maintain the most efficient lift-off attitude/configuration for obstacle clearance.

AP.III.D.S8 Maintain the recommended airspeed and aircraft configuration until the obstacle is cleared.

AP.III.D.S9 After clearing the obstacle, establish pitch attitude and aircraft configuration for VY and accelerate to and maintain VY ±5 knots during the climb.

AP.III.D.S10 Reconfigure the aircraft after a positive rate of climb has been verified or in accordance with the aircraft manufacturer's guidance.

AP.III.D.S11 Maintain directional control and proper wind-drift correction throughout takeoff and climb.

AP.III.D.S12 Comply with noise abatement procedures.

AP.III.D.S13 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation IV. In-flight Maneuvers › Task A. Steep Turns

Area of Operation IV. In-flight Maneuvers

Area of Operation IV. In-flight Maneuvers

Task A. Steep Turns

References: FAA-H-8083-2, FAA-H-8083-25; FSB Report (type specific); Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with steep turns.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.IV.A.K1 Energy management concepts.

AP.IV.A.K2 Aerodynamics associated with steep turns, including:

AP.IV.A.K2a a. Maintaining coordinated flight

AP.IV.A.K2b b. Overbanking tendencies

AP.IV.A.K2c c. Maneuvering speed, including the impact of weight changes

AP.IV.A.K2d d. Load factor and accelerated stalls

AP.IV.A.K2e e. Rate and radius of turn

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.IV.A.R1 Spatial disorientation when conducting a steep turn while flying by reference to instruments.

AP.IV.A.R2 Collision hazards.

AP.IV.A.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

AP.IV.A.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.

AP.IV.A.R5 Uncoordinated flight.

Skills: The applicant demonstrates how to:

AP.IV.A.S1 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet above ground level (AGL).

AP.IV.A.S2 Establish the manufacturer’s recommended airspeed or, if one is not available, a safe airspeed not to exceed manuevering speed (VA).

AP.IV.A.S3 Establish a configuration and bank angle as specified by the evaluator and make a coordinated turn of at least 180 degrees solely by reference to instruments.

AP.IV.A.S4 Perform the Task in the opposite direction, as specified by evaluator.

AP.IV.A.S5 Make smooth pitch, bank, and power adjustments as needed.

AP.IV.A.S6 Maintain the entry altitude ±100 feet, airspeed ±10 knots, bank ±5°, and roll out on the entry heading ±10°.

AP.IV.A.S7 Avoid any indication of an impending stall, abnormal flight attitude, or exceeding any structural or operating limitation during any part of the Task.

Area of Operation IV. In-flight Maneuvers

AP.IV.A.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation IV. In-flight Maneuvers › Task B. Specific Flight Characteristics

Task B. Specific Flight Characteristics

References: FAA-H-8083-2, FAA-H-8083-25; FSB Report (type specific); Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight and performance characteristics unique to a specific aircraft type.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.IV.B.K1 All specific flight and performance characteristics associated with the aircraft.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.IV.B.R1 Specific flight and performance characteristics, their effects, and applicable procedures.

AP.IV.B.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.IV.B.S1 Use proper techniques, checklists, and procedures to enter into, operate within, and recover from specific flight situations, as applicable.

Area of Operation IV. In-flight Maneuvers › Task C. Inflight Conversion During Straight-and-Level Flight

Task C. Inflight Conversion During Straight-and-Level Flight

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with converting from thrust-borne configuration to wing-borne configuration, and returning to thrust-borne configuration.

Knowledge: The applicant demonstrates understanding of:

AP.IV.C.K1 Procedures for changing aircraft configuration.

AP.IV.C.K2 Aerodynamic effects of changing aircraft configuration.

AP.IV.C.K3 Flight control operation when converting from thrust-borne to wing-borne configuration, and when converting from wing-borne to thrust-borne configuration, while in straight-and-level flight.

AP.IV.C.K4 Aircraft performance and limitation charts.

AP.IV.C.K5 Factors related to weight and balance and center of gravity (CG) envelopes.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.IV.C.R1 Aircraft performance limitations.

AP.IV.C.R2 Powerplant failure during conversion.

AP.IV.C.R3 Aerodynamic stall.

Area of Operation IV. In-flight Maneuvers

AP.IV.C.R4 Effects of gross weight and CG.

AP.IV.C.R5 Rapid configuration or thrust vector changes.

AP.IV.C.R6 Other hazards specific to the powered-lift make and model.

AP.IV.C.R7 Altitude variation/vertical speed.

AP.IV.C.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.IV.C.S1 Convert from thrust-borne configuration to wing-borne configuration during straight-and-level flight.

AP.IV.C.S2 Convert the aircraft from wing-borne configuration to thrust-borne configuration during straight-andlevel flight.

AP.IV.C.S3 Utilize proper control technique throughout the maneuver.

AP.IV.C.S4 Maintain awareness of aircraft performance, limitations, and relative position throughout the maneuver.

AP.IV.C.S5 Maintain altitude ±100 feet and specified heading ±10° throughout the operation. Achieve and maintain targeted airspeed ±10 knots.

AP.IV.C.S6 Use the appropriate checklist, if applicable.

AP.IV.C.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation IV. In-flight Maneuvers › Task D. Power-On Stall Prevention

Task D. Power-On Stall Prevention

References: FAA-H-8083-2, FAA-H-8083-25; FSB Report (type specific); Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-on stalls.

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.IV.D.K1 Aerodynamics associated with stalls in wing-borne configuration, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and balance, CG, aircraft attitude and configuration.

AP.IV.D.K2 Stall characteristics and prevention as they relate to aircraft design and impending stall and full stall indications using sight, sound, or feel.

AP.IV.D.K3 Factors and situations that can lead to a power-on stall and actions that can be taken to prevent it.

AP.IV.D.K4 Effects of autoflight, flight envelope protection in normal and degraded modes, and unexpected disconnects of the autopilot, if applicable to the aircraft used for the evaluation.

AP.IV.D.K5 Fundamentals of stall recovery.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.IV.D.R1 Factors and situations that could lead to an inadvertent power-on stall, spin, and loss of control.

AP.IV.D.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).

Area of Operation IV. In-flight Maneuvers

AP.IV.D.R3 Stall recognition and recovery procedures.

AP.IV.D.R4 Secondary and accelerated stalls.

AP.IV.D.R5 Effects of environmental elements on aircraft performance as they related to stalls (e.g., turbulence, microbursts, and high density altitude).

AP.IV.D.R6 Collision hazards including aircraft and terrain.

AP.IV.D.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.IV.D.S1 Clear the area and select an entry altitude that allows the recovery to be completed no lower than 3,000 feet above ground level (AGL).

AP.IV.D.S2 Establish the takeoff, departure, or wing-borne configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver in simulated or actual instrument meteorological conditions (IMC).

AP.IV.D.S3 Either manually or with the autopilot engaged, smoothly adjust pitch attitude, bank angle not to exceed 20°, and power setting in accordance with evaluator’s instructions to an impending stall.

AP.IV.D.S4 Acknowledge the cue(s) and initiate a recovery at the first indication of a stall.

AP.IV.D.S5 Execute a stall recovery in accordance with procedures set forth in the Flight Manual.

AP.IV.D.S6 Return to the altitude, heading, aircraft configuration, and airspeed specified by the evaluator.

AP.IV.D.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation IV. In-flight Maneuvers › Task E. Power-Off Stall Prevention

Task E. Power-Off Stall Prevention

References: FAA-H-8083-2, FAA-H-8083-25; FSB Report (type specific); Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-off stalls.

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.IV.E.K1 Aerodynamics associated with stalls in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.

AP.IV.E.K2 Stall characteristics in various flight modes, including impending stall and full stall indications.

AP.IV.E.K3 Factors and situations that can lead to a stall during flight and actions that can be taken to prevent it.

AP.IV.E.K4 Effects of autoflight, flight envelope protection in normal and degraded modes, and unexpected disconnects of the autopilot, if applicable to the aircraft used for the evaluation.

AP.IV.E.K5 Fundamentals of stall avoidance and recovery.

AP.IV.E.K6 Effects of altitude on performance and flight control effectiveness during a recovery.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

Area of Operation IV. In-flight Maneuvers

AP.IV.E.R1 Factors and situations that could lead to an inadvertent power-off stall, spin, and loss of control.

AP.IV.E.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).

AP.IV.E.R3 Stall recognition and recovery procedures.

AP.IV.E.R4 Secondary and accelerated stalls.

AP.IV.E.R5 Effects of environmental elements on aircraft performance as they related to stalls (e.g., turbulence, microbursts, and high density altitude).

AP.IV.E.R6 Collision hazards including aircraft and terrain.

AP.IV.E.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.IV.E.S1 Clear the area and select an entry altitude that allows the recovery to be completed no lower than 3,000 feet above ground level (AGL).

AP.IV.E.S2 Configure the aircraft in the approach or landing configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver in simulated or actual instrument meteorological conditions (IMC).

AP.IV.E.S3 Either manually or with the autopilot engaged, smoothly adjust pitch attitude, bank angle not to exceed 20°, and power setting in accordance with evaluator’s instructions to an impending stall.

AP.IV.E.S4 Acknowledge the cue(s) and promptly recover at the first indication of an impending stall (e.g., buffet, stall horn, stick shaker, etc.).

AP.IV.E.S5 Execute a stall recovery in accordance with procedures set forth in the Flight Manual.

AP.IV.E.S6 Configure the aircraft as recommended by the manufacturer and accelerate to VX or VY.

AP.IV.E.S7 Return to the altitude, heading, aircraft configuration, and airspeed specified by the evaluator.

AP.IV.E.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation V. Instrument Procedures › Task A. Instrument Takeoff

Area of Operation V. Instrument Procedures

Area of Operation V. Instrument Procedures

Task A. Instrument Takeoff

References: 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Flight Manual; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with an instrument takeoff.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.V.A.K1 Operational factors that could affect an instrument takeoff (e.g., runway length, runway lighting, surface conditions, wind, wake turbulence, icing conditions, obstructions, available instrument approaches or alternate airports available) in the event of an emergency after takeoff.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.A.R1 Selection of a runway based on aircraft performance and limitations, available distance, surface conditions, lighting, and wind.

AP.V.A.R2 Wake turbulence.

AP.V.A.R3 Abnormal operations, including planning for:

AP.V.A.R3a a. Rejected takeoff

AP.V.A.R3b b. Potential failure of any powerplant(s) in the takeoff/climb phase of flight with the ceiling or

visibility below the minimums for an instrument approach at departure airport

AP.V.A.R4 Collision hazards.

AP.V.A.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

AP.V.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.V.A.S1 Coordinate with crew, if applicable, and complete the appropriate checklist(s) prior to takeoff in a timely manner.

AP.V.A.S2 Properly set the applicable avionics and flight instruments prior to initiating the takeoff.

AP.V.A.S3 Make radio calls as appropriate.

AP.V.A.S4 Verify assigned/correct runway.

AP.V.A.S5 Position the flight controls for the existing wind, if applicable.

AP.V.A.S6 Clear the area, taxi into takeoff position, and align the aircraft on the runway centerline.

AP.V.A.S7 Perform an instrument takeoff with instrument meteorological conditions (IMC) simulated at or before reaching an altitude of 100 feet above ground level (AGL). If accomplished in a full flight simulator, visibility should be no greater than ¼ mile, or as specified by applicable operations specifications, whichever is lower.

AP.V.A.S8 Maintain centerline and proper flight control inputs during the takeoff roll.

Area of Operation V. Instrument Procedures

AP.V.A.S9 Confirm takeoff power, powerplant and flight instrument indications for the aircraft or per the operator’s procedures.

AP.V.A.S10 Lift off or depart at the recommended airspeed, establish the desired pitch attitude, and accelerate to the desired airspeed/V-speed.

AP.V.A.S11 Transition smoothly from visual meteorological conditions (VMC) to actual or simulated instrument meteorological conditions (IMC).

AP.V.A.S12 Maintain desired heading ±5° and desired airspeeds ±5 knots.

AP.V.A.S13 Comply with air traffic control (ATC) clearances and instructions issued by ATC or the evaluator, as appropriate.

AP.V.A.S14 Complete appropriate after takeoff checklist(s) in a timely manner.

AP.V.A.S15 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation V. Instrument Procedures › Task B. Departure Procedures

Task B. Departure Procedures

References: 14 CFR part 91; AC 90-100; AIM; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Flight Manual; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with instrument departure procedures (DPs).

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.V.B.K1 Takeoff minimums; (Obstacle) Departure Procedure (ODP), including Visual Climb over the Airport (VCOA) and Diverse Vector Area (Radar Vectors); Standard Instrument Departure (SID), including Area Navigation (RNAV) departure; required climb gradients; U.S. Terminal Procedures Publications; and En Route Charts.

AP.V.B.K2 Use of a Flight Management System (FMS) or Global Positioning System (GPS) to follow a DP.

AP.V.B.K3 Pilot/controller responsibilities, communication procedures, and ATC services available to pilots.

AP.V.B.K4 Two-way radio communication failure procedures after takeoff.

AP.V.B.K5 Ground-based and satellite-based navigation systems (orientation, course determination, equipment, tests and regulations, interference, appropriate use of navigation data, signal integrity).

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.B.R1 Following published procedures and required climb gradients or ATC Instructions.

AP.V.B.R2 Limitations of air traffic avoidance equipment and use of see and avoid techniques.

AP.V.B.R3 Automation management.

Skills: The applicant exhibits the skill to:

AP.V.B.S1 Select the appropriate instrument departure procedure. Then select, identify (as necessary), and use the appropriate communication and navigation facilities associated with the procedure.

Area of Operation V. Instrument Procedures

AP.V.B.S2 Program the FMS prior to departure and set avionics, including flight director and autopilot controls, as appropriate, for the departure, if applicable.

AP.V.B.S3 Coordinate with crew, if applicable, and complete the appropriate checklist(s) in a timely manner.

AP.V.B.S4 Use current and appropriate navigation publications or databases for the proposed flight.

AP.V.B.S5 Establish two-way communications with the proper controlling agency, use proper phraseology, comply, in a timely manner, with all ATC instructions and airspace restrictions, and exhibit adequate knowledge of communication failure procedures.

AP.V.B.S6 Intercept all courses, radials, and bearings appropriate to the procedure, route, clearance, or as directed by the evaluator in a timely manner.

AP.V.B.S7 Comply with all applicable charted procedures.

AP.V.B.S8 Maintain the appropriate airspeed ±10 knots, headings ±10°, and altitude ±100 feet, and accurately track a course, radial, or bearing.

AP.V.B.S9 Conduct the departure phase to a point where, in the opinion of the evaluator, the transition to the en route environment is complete.

Area of Operation V. Instrument Procedures › Task C. Arrival Procedures

Task C. Arrival Procedures

References: 14 CFR part 91; AC 90-100; AIM; IFR Enroute Charts; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Flight Manual; Profile Descent Charts; STARs; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with Instrument Flight Rules (IFR) arrival procedures.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.V.C.K1 Standard Terminal Arrival (STAR) charts, U.S. Terminal Procedures Publications, and IFR En Route High and Low Altitude Charts.

AP.V.C.K2 Use of a Flight Management System (FMS) or GPS to follow a STAR.

AP.V.C.K3 Pilot/controller responsibilities, communication procedures, and ATC services available to pilots.

AP.V.C.K4 Two-way radio communication failure procedures during an arrival.

AP.V.C.K5 Ground-based and satellite-based navigation systems (orientation, course determination, equipment, tests and regulations, interference, appropriate use of navigation data, signal integrity).

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.C.R1 ATC communications and compliance with published procedures.

AP.V.C.R2 Limitations of traffic avoidance equipment.

AP.V.C.R3 Responsibility to use "see and avoid" techniques when possible.

AP.V.C.R4 Automation management.

AP.V.C.R5 ATC instructions that modify an arrival or discontinue/resume the aircraft's lateral or vertical navigation on an arrival.

Area of Operation V. Instrument Procedures

Skills: The applicant exhibits the skill to:

AP.V.C.S1 In actual or simulated instrument conditions, select, identify (as necessary) and use the appropriate communication and navigation facilities associated with the arrival.

AP.V.C.S2 Set FMS and avionics, including flight director and autopilot controls for the arrival, if applicable.

AP.V.C.S3 Coordinate with crew, if applicable, and complete the appropriate checklist(s) in a timely manner.

AP.V.C.S4 Use current and appropriate navigation publications or databases for the proposed flight.

AP.V.C.S5 Establish two-way communications with the proper controlling agency, use proper phraseology and comply, in a timely manner, with all ATC instructions and airspace restrictions as well as exhibit adequate knowledge of communication failure procedures.

AP.V.C.S6 Intercept all courses, radials, and bearings appropriate to the procedure, route, clearance, or as directed by the evaluator in a timely manner.

AP.V.C.S7 Comply with all applicable charted procedures.

AP.V.C.S8 Adhere to airspeed restrictions required by regulation, procedure, aircraft limitation, ATC, or the evaluator.

AP.V.C.S9 Establish rates of descent consistent with the route segment, aircraft operating characteristics and safety.

AP.V.C.S10 Maintain the appropriate airspeed/V-speed ±10 knots, heading ±10°, altitude ±100 feet, and accurately track radials, courses, and bearings.

Area of Operation V. Instrument Procedures › Task D. Non-precision Approaches

Task D. Non-precision Approaches

References: 14 CFR part 91; AC 120-108; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with performing non-precision approach procedures.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.V.D.K1 Procedures and limitations associated with a non-precision approach, including the differences between Localizer Performance (LP) and Lateral Navigation (LNAV) approach guidance.

AP.V.D.K2 Navigation system displays and annunciations, modes of operation, and Required Navigation Performance (RNP) lateral accuracy values associated with an RNAV (GPS) approach.

AP.V.D.K3 Ground-based and satellite-based navigation systems (orientation, course determination, equipment, tests and regulations, interference, appropriate use of navigation data, signal integrity).

AP.V.D.K4 A stabilized approach, including energy management concepts.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.D.R1 Deviating from the assigned approach procedure.

AP.V.D.R2 Selecting a navigation frequency.

AP.V.D.R3 Management of automated navigation and autoflight systems.

Area of Operation V. Instrument Procedures

AP.V.D.R4 Aircraft configuration during an approach and missed approach.

AP.V.D.R5 An unstable approach, including excessive descent rates.

AP.V.D.R6 Deteriorating weather conditions on approach.

AP.V.D.R7 Operating below the minimum descent altitude (MDA) without proper visual references.

Skills: The applicant exhibits the skill to:

AP.V.D.S1 Accomplish the non-precision instrument approaches selected by the evaluator.

AP.V.D.S2 Establish two-way communications with air traffic control (ATC) appropriate for the phase of flight or approach segment, and use proper communication phraseology.

AP.V.D.S3 Select, tune, identify, and confirm the operational status of navigation equipment to be used for the approach.

AP.V.D.S4 Comply with all clearances issued by ATC or the evaluator.

AP.V.D.S5 Recognize if any flight instrumentation is inaccurate or inoperative, and take appropriate action.

AP.V.D.S6 Advise ATC or the evaluator if unable to comply with a clearance.

AP.V.D.S7 Coordinate with crew, if applicable, and complete the appropriate checklist(s) in a timely manner.

AP.V.D.S8 Establish the appropriate aircraft configuration and airspeed considering meteorological and operating conditions.

AP.V.D.S9 Maintain altitude ±100 feet, selected heading ±5°, airspeed ±10 knots, and accurately track radials, courses, and bearings, prior to beginning the final approach segment.

AP.V.D.S10 Adjust the published MDA/Derived Decision Altitude (DDA) and visibility criteria for the aircraft approach category, as appropriate, for factors that include Notices to Air Missions (NOTAMs), inoperative aircraft or navigation equipment, or inoperative visual aids associated with the landing environment, etc.

AP.V.D.S11 Establish a stabilized descent to the appropriate altitude.

AP.V.D.S12 For the final approach segment, maintain no more than ¼ scale course deviation indicator (CDI) deflection, airspeed ±5 knots of selected value, and altitude above MDA +50/-0 feet [to the visual descent point (VDP) or missed approach point (MAP)].

AP.V.D.S13 Assess if the required visual references are available, and either initiate the missed approach procedure or continue for landing.

AP.V.D.S14 Use a Multi-Function Display (MFD) and other graphical navigation displays, if installed, to monitor position, track wind drift and other parameters to maintain desired flightpath.

Area of Operation V. Instrument Procedures › Task E. Precision Approaches

Task E. Precision Approaches

References: 14 CFR parts 91, 97; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with performing precision approach procedures.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

Area of Operation V. Instrument Procedures

AP.V.E.K1 Procedures and limitations associated with a precision approach, including determining required descent rates and adjusting minimums in the case of inoperative equipment.

AP.V.E.K2 Navigation system displays, annunciations, and modes of operation.

AP.V.E.K3 Ground-based and satellite-based navigation systems (orientation, course determination, equipment, tests and regulations, interference, appropriate use of navigation data, signal integrity).

AP.V.E.K4 A stabilized approach, including energy management concepts.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.E.R1 Deviating from the assigned approach procedure.

AP.V.E.R2 Selecting a navigation frequency.

AP.V.E.R3 Management of automated navigation and autoflight systems.

AP.V.E.R4 Aircraft configuration during an approach and missed approach.

AP.V.E.R5 An unstable approach, including excessive descent rates.

AP.V.E.R6 Deteriorating weather conditions on approach.

AP.V.E.R7 Continuing to descend below the Decision Altitude (DA)/Decision Height (DH) when the required visual references are not visible.

Skills: The applicant exhibits the skill to:

AP.V.E.S1 Accomplish the precision instrument approaches selected by the evaluator.

AP.V.E.S2 Establish two-way communications with air traffic control (ATC) appropriate for the phase of flight or approach segment, and use proper communication phraseology.

AP.V.E.S3 Select, tune, identify, and confirm the operational status of navigation equipment to be used for the approach.

AP.V.E.S4 Comply in a timely manner with all clearances, instructions, and procedures.

AP.V.E.S5 Recognize if any flight instrumentation is inaccurate or inoperative, and take appropriate action.

AP.V.E.S6 Advise ATC or the evaluator if unable to comply with a clearance.

AP.V.E.S7 Conduct the approach briefing, coordinate with crew, if applicable, and complete the appropriate checklist(s) in a timely manner.

AP.V.E.S8 Establish the appropriate aircraft configuration and airspeed considering meteorological and operating conditions.

AP.V.E.S9 Maintain altitude ±100 feet, selected heading ±5°, airspeed ±10 knots, and accurately track radials, courses, and bearings, prior to beginning the final approach segment.

AP.V.E.S10 Adjust the published DA/DH and visibility criteria for the aircraft approach category, as appropriate, to account for NOTAMS, inoperative aircraft or navigation equipment, or inoperative visual aids associated with the landing environment.

AP.V.E.S11 Establish a predetermined rate of descent at the point where vertical guidance begins, which approximates that required for the aircraft to follow the vertical guidance.

Area of Operation V. Instrument Procedures

AP.V.E.S12 Maintain a stabilized final approach from the Final Approach Fix (FAF) to DA/DH allowing no more than ¼-scale deflection of either the vertical or lateral guidance indications and maintain the desired airspeed ±5 knots.

AP.V.E.S13 Assess if the required visual references are available, and either initiate the missed approach procedure or continue for landing.

AP.V.E.S14 Use an MFD and other graphical navigation displays, if installed, to monitor position, track wind drift and other parameters to maintain desired flightpath.

Area of Operation V. Instrument Procedures › Task F. Landing from a Precision Approach

Task F. Landing from a Precision Approach

References: 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with performing procedures for a landing from an instrument approach.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with performing procedures for a landing from an instrument approach.

Knowledge: The applicant demonstrates understanding of:

AP.V.F.K1 Elements related to the pilot’s responsibilities, and the environmental, operational, and meteorological factors that affect landing from a precision approach.

AP.V.F.K2 Approach lighting systems and runway and taxiway signs, markings, and lighting.

AP.V.F.K3 Appropriate landing profiles and aircraft configurations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.F.R1 Selection of an approach procedure and runway based on aircraft limitations, available distance, surface conditions, and wind.

AP.V.F.R2 Wake turbulence.

AP.V.F.R3 Missed Approach.

AP.V.F.R4 Collision hazards.

AP.V.F.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

AP.V.F.R6 Attempting to land from an unstable approach.

AP.V.F.R7 Flying below the glidepath.

AP.V.F.R8 Transitioning from instrument to visual references for landing.

Skills: The applicant exhibits the skill to:

AP.V.F.S1 Transition at the DA/DH to a visual flight condition, allowing for safe visual maneuvering and a normal landing.

AP.V.F.S2 Adhere to all ATC or evaluator advisories, such as NOTAMs, windshear, wake turbulence, runway surface, and other operational considerations.

Area of Operation V. Instrument Procedures

AP.V.F.S3 Coordinate with crew, if applicable, and complete the appropriate checklist(s) in a timely manner.

AP.V.F.S4 Maintain positive aircraft control throughout the landing maneuver.

AP.V.F.S5 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

AP.V.F.S6 Use runway incursion avoidance procedures, if applicable.

Area of Operation V. Instrument Procedures › Task G. Circling Approach

Task G. Circling Approach

References: 14 CFR parts 91, 97; AIM; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with performing a circling approach procedure.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.V.G.K1 Elements related to circling approach procedures and limitations, including approach categories and related airspeed restrictions.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.G.R1 Prescribed circling approach procedures.

AP.V.G.R2 Executing a circling approach at night or with marginal visibility.

AP.V.G.R3 Losing visual contact with an identifiable part of the airport.

AP.V.G.R4 Management of automated navigation and autoflight systems.

AP.V.G.R5 Management of altitude, airspeed, or distance while circling.

AP.V.G.R6 Collision hazards.

AP.V.G.R7 Executing a missed approach after the MAP while circling.

Skills: The applicant exhibits the skill to:

AP.V.G.S1 Comply with the circling approach procedure considering turbulence, windshear, and the maneuvering capability and approach category of the aircraft.

AP.V.G.S2 Confirm the direction of traffic and adhere to all restrictions and instructions issued by ATC or the evaluator.

AP.V.G.S3 Coordinate with crew, if applicable, and complete the appropriate checklist(s) in a timely manner.

AP.V.G.S4 Establish the approach and landing configuration. Maintain a stabilized approach and a descent rate that ensures arrival at the MDA, or the preselected circling altitude above the MDA, prior to the missed approach point.

AP.V.G.S5 Maintain airspeed ±5 knots, desired heading/track ±5°, and altitude +100/-0 feet until descending below the MDA or the preselected circling altitude above the MDA.

AP.V.G.S6 Visually maneuver to a base or downwind leg appropriate for the landing runway and environmental conditions.

Area of Operation V. Instrument Procedures

AP.V.G.S7 If a missed approach occurs, turn in the appropriate direction using the correct procedure and appropriately configure the aircraft.

AP.V.G.S8 If landing, initiate a stabilized descent. Touch down on the first one-third of the selected runway without excessive maneuvering, without exceeding the normal operating limits of the aircraft, and without exceeding 30° of bank.

Area of Operation V. Instrument Procedures › Task H. Missed Approach

Task H. Missed Approach

References: 14 CFR parts 91, 97; AIM; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with performing a missed approach procedure.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.V.H.K1 Elements related to missed approach procedures, including reference to standby or backup instruments.

AP.V.H.K2 Limitations associated with standard instrument approaches, including while using an FMS or autopilot, if equipped.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.H.R1 Deviations from prescribed procedures or ATC instructions.

AP.V.H.R2 Holding, diverting, or electing to fly the approach again.

AP.V.H.R3 Aircraft configuration during an approach and missed approach.

AP.V.H.R4 Factors that might lead to executing a missed approach procedure before the MAP or to a go-around below DA, DH, or MDA, as applicable.

AP.V.H.R5 Management of automated navigation and autoflight systems.

Skills: The applicant exhibits the skill to:

AP.V.H.S1 Promptly initiate the missed approach procedure and report it to ATC.

AP.V.H.S2 Apply the appropriate power setting and aircraft configuration for the flight conditions to obtain the desired performance.

AP.V.H.S3 Configure the aircraft, if appropriate, and at a safe altitude, and establish a positive rate of climb and the appropriate airspeed/V-speed, ±5 knots.

AP.V.H.S4 Coordinate with crew, if applicable, and complete the appropriate procedures and checklist(s) in a timely manner.

AP.V.H.S5 Comply with the published or alternate missed approach procedure.

AP.V.H.S6 Advise ATC or the evaluator if unable to comply with a clearance, restriction, or climb gradient.

AP.V.H.S7 Maintain the heading, course, or bearing ±5°, and altitude(s) ±100 feet during the missed approach procedure where applicable.

Area of Operation V. Instrument Procedures

AP.V.H.S8 Use an MFD and other graphical navigation displays, if installed, to monitor position and track to help navigate the missed approach.

AP.V.H.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

AP.V.H.S10 Re-engage autopilot, if installed, at appropriate times during the missed approach procedure.

AP.V.H.S11 Request ATC clearance to attempt another approach, proceed to the alternate airport, holding fix, or other clearance limit, as appropriate, or as directed by the evaluator.

Area of Operation V. Instrument Procedures › Task I. Holding Procedures

Task I. Holding Procedures

References: 14 CFR part 91; AC 91-74; AIM; FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Flight Manual; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with holding procedures.

Knowledge: The applicant demonstrates understanding of:

AP.V.I.K1 Elements related to holding procedures, including reporting criteria, appropriate speeds, and recommended entry procedures for standard, nonstandard, published, and non-published holding patterns.

AP.V.I.K2 Determining holding endurance based upon factors, including an expect further clearance (EFC) time, fuel on board, fuel flow while holding, fuel required to destination and alternate, etc., as appropriate.

AP.V.I.K3 When to declare minimum fuel or a fuel-related emergency.

AP.V.I.K4 Use of automation for holding, including autopilot and flight management systems, if equipped.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.V.I.R1 Recalculating fuel reserves if assigned an unanticipated expect further clearance (EFC) time.

AP.V.I.R2 Scenarios and circumstances that could result in minimum fuel or the need to declare an emergency.

AP.V.I.R3 Scenarios that could lead to holding, including deteriorating weather at the planned destination.

AP.V.I.R4 Holding entry and wind correction while holding.

AP.V.I.R5 Holding while in icing conditions.

AP.V.I.R6 Automation management.

Skills: The applicant exhibits the skill to:

AP.V.I.S1 Correctly identify instrument navigation aids associated with the assigned hold.

AP.V.I.S2 Use an entry procedure appropriate for a standard, nonstandard, published, or non-published holding pattern.

AP.V.I.S3 Change to the appropriate holding airspeed for the aircraft and holding altitude to cross the holding fix at or below maximum holding airspeed.

AP.V.I.S4 Comply with the holding pattern leg length and other restrictions, if applicable, associated with the holding pattern.

AP.V.I.S5 Comply with ATC reporting requirements.

Area of Operation V. Instrument Procedures

AP.V.I.S6 Use proper wind correction procedures to maintain the desired pattern and to arrive over the fix as close as possible to a specified time.

AP.V.I.S7 Maintain specified airspeed ±10 knots, altitude ±100 feet, headings ±10°, and accurately track a selected course, radial, or bearing.

AP.V.I.S8 If available, use automation, including autopilot, flight director controls, and navigation displays associated with the assigned hold.

AP.V.I.S9 Update fuel reserve calculations based on EFC times.

Area of Operation VI. Landings and Approaches to Landings › Task A. Normal Approach and Landing

Area of Operation VI. Landings and Approaches to Landings

Area of Operation VI. Landings and Approaches to Landings

Task A. Normal Approach and Landing

References: 14 CFR part 91; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a normal approach and landing.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.

Knowledge: The applicant demonstrates understanding of:

AP.VI.A.K1 Effects of atmospheric conditions, including wind, on approach speed and angle.

AP.VI.A.K2 A stabilized approach, including energy management concepts.

AP.VI.A.K3 Use of proper thrust vector angle for transition to landing.

AP.VI.A.K4 Performance data and the height velocity (H/V) diagram.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VI.A.R1 Arrival point selection.

AP.VI.A.R2 Effects of:

AP.VI.A.R2a a. Crosswind

AP.VI.A.R2b b. Windshear

AP.VI.A.R2c c. Tailwind

AP.VI.A.R2d d. Wake turbulence

AP.VI.A.R2e e. Runway/arrival point surface/condition

AP.VI.A.R3 Planning for:

AP.VI.A.R3a a. Rejected landing and go-around

AP.VI.A.R3b b. Powerplant failure during the approach

AP.VI.A.R4 Collision hazards.

AP.VI.A.R5 Distractions and task management, lapse in situational awareness, and identifying the airport surface approach and landing area.

Skills: The applicant exhibits the skill to:

AP.VI.A.S1 Complete the appropriate checklist(s).

AP.VI.A.S2 Make radio calls as appropriate.

AP.VI.A.S3 Use manufacturer's recommended technique and remain within airspeed range allowed for each configuration change.

Area of Operation VI. Landings and Approaches to Landings

AP.VI.A.S4 Consider the wind conditions, landing surface, and obstructions and select a suitable landing point.

AP.VI.A.S5 Maintain proper ground track with crosswind correction, if necessary.

AP.VI.A.S6 Fly a stabilized approach.

AP.VI.A.S7 Execute a timely go-around for any condition that may result in an unsafe approach or landing.

AP.VI.A.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation VI. Landings and Approaches to Landings › Task B. Normal Approach to a Hover

Task B. Normal Approach to a Hover

References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with approach profile to a hover.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.VI.B.K1 Types of approaches and applicability.

AP.VI.B.K2 Performance data and the height velocity (H/V) diagram.

AP.VI.B.K3 Effects of atmospheric conditions, including wind and density altitude, on approach and hover performance.

AP.VI.B.K4 Wind correction techniques on approach and hover.

AP.VI.B.K5 Aircraft configurations for the approach and hover.

AP.VI.B.K6 Aircraft performance and limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VI.B.R1 Selection of runway/helipad/touchdown point based on aircraft performance and limitations, available distance, and wind.

AP.VI.B.R2 Effects of:

AP.VI.B.R2a a. Crosswind

AP.VI.B.R2b b. Windshear

AP.VI.B.R2c c. Tailwind

AP.VI.B.R2d d. Wake turbulence

AP.VI.B.R2e e. Vortex ring state (VRS)

AP.VI.B.R2f f. Runway/arrival point surface/condition

AP.VI.B.R3 Situations including:

AP.VI.B.R3a a. Rejected landing and go-around

AP.VI.B.R3b b. Powerplant failure during the approach

AP.VI.B.R4 Collision hazards.

Area of Operation VI. Landings and Approaches to Landings

AP.VI.B.R5 Flat light conditions.

AP.VI.B.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.VI.B.S1 Complete the appropriate checklist(s).

AP.VI.B.S2 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.

AP.VI.B.S3 Use the appropriate techniques and aircraft configurations through all stages of the approach.

AP.VI.B.S4 Consider the wind conditions, landing surface, and obstructions and select a suitable hover point.

AP.VI.B.S5 Maintain appropriate ground track with crosswind correction throughout the approach.

AP.VI.B.S6 Fly a stabilized approach.

AP.VI.B.S7 Arrive over the arrival point at a stabilized hover ±2 feet.

AP.VI.B.S8 Execute a timely go-around for any condition that may result in an unsafe approach or landing.

AP.VI.B.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

AP.VI.B.S10 Use runway incursion avoidance procedures, if applicable.

Area of Operation VI. Landings and Approaches to Landings › Task C. Steep Approach and Landing

Task C. Steep Approach and Landing

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a steep approach to the surface.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.VI.C.K1 A stabilized steep approach.

AP.VI.C.K2 Approach techniques and applicability.

AP.VI.C.K3 Performance data and the height velocity (H/V) diagram.

AP.VI.C.K4 Effects of atmospheric conditions on approach and landing performance.

AP.VI.C.K5 Wind correction techniques.

AP.VI.C.K6 Aircraft configuration.

AP.VI.C.K7 Aircraft performance and limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VI.C.R1 Selection of the approach path and landing area.

AP.VI.C.R2 Effects of:

AP.VI.C.R2a a. Crosswind

Area of Operation VI. Landings and Approaches to Landings

AP.VI.C.R2b b. Windshear

AP.VI.C.R2c c. Tailwind

AP.VI.C.R2d d. Wake turbulence

AP.VI.C.R2e e. Vortex ring state (VRS)

AP.VI.C.R2f f. Landing point condition

AP.VI.C.R3 Planning for:

AP.VI.C.R3a a. Rejected landing and go-around

AP.VI.C.R3b b. Powerplant failure during the approach

AP.VI.C.R4 Landing in an area or in conditions where a takeoff/climb may not be possible.

AP.VI.C.R5 Degraded Visual Environment (DVE) and flat light conditions.

AP.VI.C.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.VI.C.S1 Complete the appropriate checklist(s).

AP.VI.C.S2 Position the flight controls, including the thrust vector, for the prevailing environmental conditions.

AP.VI.C.S3 Maintain awareness of aircraft performance, limitations, and relative position throughout the maneuver.

AP.VI.C.S4 Arrive over the touchdown point on the surface ±5 feet from intended landing point or, at the discretion of the evaluator, at a stabilized hover ±5 feet height.

AP.VI.C.S5 Maintain proper ground track with crosswind correction, if necessary.

AP.VI.C.S6 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

AP.VI.C.S7 Use runway incursion avoidance procedures, if applicable.

Area of Operation VI. Landings and Approaches to Landings › Task D. Running/Roll-On Landing

Task D. Running/Roll-On Landing

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with running/roll-on landing operation.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.

Knowledge: The applicant demonstrates understanding of:

AP.VI.D.K1 H/V diagram, if applicable.

AP.VI.D.K2 Aircraft performance and limitations.

AP.VI.D.K3 Aircraft configuration.

AP.VI.D.K4 Effects of atmospheric conditions, including wind, on approach and landing performance.

Area of Operation VI. Landings and Approaches to Landings

AP.VI.D.K5 Wind correction techniques on approach and landing.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VI.D.R1 Situations including:

AP.VI.D.R1a a. Powerplant failure during approach

AP.VI.D.R1b b. Rejected landing

AP.VI.D.R2 Effects of:

AP.VI.D.R2a a. Crosswind

AP.VI.D.R2b b. Windshear

AP.VI.D.R2c c. Tailwind

AP.VI.D.R2d d. Wake turbulence

AP.VI.D.R2e e. Runway surface/condition

AP.VI.D.R3 Collision hazards.

AP.VI.D.R4 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

AP.VI.D.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.VI.D.S1 Coordinate with crew, if applicable, and complete the appropriate checklist(s), prior to takeoff.

AP.VI.D.S2 Ensure the aircraft is correctly configured for the landing.

AP.VI.D.S3 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.

AP.VI.D.S4 Maintain a ground track that ensures the desired traffic pattern flown takes into consideration obstructions and ATC or evaluator instructions.

AP.VI.D.S5 Ensure the aircraft is aligned with the correct/assigned runway or landing surface.

AP.VI.D.S6 Consider the wind conditions, aircraft performance, landing surface, obstructions, and select a suitable touchdown point.

AP.VI.D.S7 Maintain crosswind correction and directional control throughout the approach and landing.

AP.VI.D.S8 Make smooth, timely, and correct control application during round out and touchdown.

AP.VI.D.S9 Touch down at the appropriate speed, aircraft configuration and pitch attitude.

AP.VI.D.S10 On touchdown, maintain proper ground track.

AP.VI.D.S11 After touchdown, reconfigure the aircraft for surface/hover taxi.

AP.VI.D.S12 Execute a timely go-around for any condition that may result in an unsafe approach or landing.

AP.VI.D.S13 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

AP.VI.D.S14 Use runway incursion avoidance procedures, if applicable.

Area of Operation VI. Landings and Approaches to Landings

Area of Operation VI. Landings and Approaches to Landings › Task E. Go-Around/Rejected Landing

Task E. Go-Around/Rejected Landing

References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a go-around/rejected landing.

Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.VI.E.K1 Situations and considerations on approach that could require a go-around/rejected landing.

AP.VI.E.K2 Effects of atmospheric conditions on a go-around or rejected landing.

AP.VI.E.K3 Aircraft configuration changes and techniques for the go-around.

AP.VI.E.K4 Go-around/rejected landing procedures, the importance of a timely decision, and appropriate airspeeds for the maneuver.

AP.VI.E.K5 Wind correction techniques.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VI.E.R1 Recognition of the need for a go-around/rejected landing.

AP.VI.E.R2 Aircraft performance.

AP.VI.E.R3 Application of power.

AP.VI.E.R4 Aircraft configuration.

AP.VI.E.R5 Collision hazards.

AP.VI.E.R6 Low altitude maneuvering, including stall or controlled flight into terrain (CFIT).

AP.VI.E.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.VI.E.S1 Make a timely decision to go-around/reject the landing.

AP.VI.E.S2 Apply the appropriate power setting for the flight condition and establish an aircraft configuration necessary to obtain the desired performance.

AP.VI.E.S3 Establish a positive rate of climb and the appropriate airspeed ±5 knots.

AP.VI.E.S4 Configure the aircraft, as appropriate.

AP.VI.E.S5 Maintain the ground track, heading, or course appropriate for the conditions, or as specified by ATC or the evaluator.

AP.VI.E.S6 Make radio calls as appropriate.

AP.VI.E.S7 Complete the appropriate checklist(s).

AP.VI.E.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

AP.VI.E.S9 Use runway incursion avoidance procedures, if applicable.

Area of Operation VII. Emergency Operations › Task A. Emergency Procedures

Area of Operation VII. Emergency Operations

Area of Operation VII. Emergency Operations

Task A. Emergency Procedures

References: 14 CFR part 91; AC 91-74; AIM; FAA-H-8083-2, FAA-H-8083-25; FSB report (type specific); Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with emergency procedures.

Knowledge: The applicant demonstrates understanding of:

AP.VII.A.K1 Declaring an emergency and selection of a suitable airport or landing location.

AP.VII.A.K2 Situations that would require an emergency descent (e.g., depressurization, smoke, or powerplant fire).

AP.VII.A.K3 Causes of inflight fire or smoke.

AP.VII.A.K4 Aircraft decompression.

AP.VII.A.K5 When an emergency evacuation may be necessary.

AP.VII.A.K6 Actions required if icing conditions exceed the capabilities of the aircraft.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VII.A.R1 Selection of the procedures or checklists to follow in an emergency.

AP.VII.A.R2 Multiple failures or system abnormalities.

AP.VII.A.R3 Altitude, wind, terrain, and obstruction considerations in an emergency.

AP.VII.A.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.VII.A.S1 Explain or describe an emergency procedure for a situation(s) presented by the evaluator.

AP.VII.A.S2 Use proper procedures for the emergency situation(s) presented by the evaluator.

AP.VII.A.S3 Fly by reference to standby flight instruments, backup instrumentation, or partial panel, if applicable and appropriate to the situation.

AP.VII.A.S4 Coordinate with crew, if applicable, and complete the appropriate checklist(s) in a timely manner.

AP.VII.A.S5 Notify/coordinate with air traffic control (ATC) or evaluator instructions as required.

AP.VII.A.S6 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation VII. Emergency Operations › Task B.

Task B. Powerplant(s) Failure (Simulated) during Takeoff in Thrust-Borne Flight

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with indications and pilot actions after powerplant(s) failure during takeoff while the aircraft is predominantly in thrust-borne flight in a multi-powerplant aircraft.

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Area of Operation VII. Emergency Operations

Note: The task outcome can be vertical or rolling depending on aircraft capabilities, configuration, and flight manual procedures.

Knowledge: The applicant demonstrates understanding of:

AP.VII.B.K1 Aircraft performance and limitations, (e.g., height velocity (H/V) diagram information).

AP.VII.B.K2 Factors involved in determining a valid go/no-go decision.

AP.VII.B.K3 Recognition of powerplant(s) failure.

AP.VII.B.K4 Pilot actions required on recognition of powerplant(s) failure, including checklist memory items.

AP.VII.B.K5 Aircraft configuration for landing with powerplant(s) failure.

AP.VII.B.K6 Causes of asymmetric thrust conditions and appropriate responses.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VII.B.R1 Powerplant(s) failure.

AP.VII.B.R2 Identification of powerplant(s) failure conditions.

AP.VII.B.R3 Pilot reaction to powerplant(s) failure conditions.

AP.VII.B.R4 Aircraft configuration.

Skills: The applicant exhibits the skill to:

AP.VII.B.S1 Recognize powerplant failures(s), maintain control, use manufacturer’s memory item procedures, and use appropriate emergency procedures.

AP.VII.B.S2 Use flight controls in the proper combination and aircraft configuration as recommended by the manufacturer, or as required to maintain best performance, and trim as required.

AP.VII.B.S3 Maintain the operating powerplant(s) within acceptable operating limits.

AP.VII.B.S4 Land the aircraft, as appropriate to the scenario presented by the evaluator.

AP.VII.B.S5 Complete the appropriate checklist(s).

AP.VII.B.S6 Make radio calls as appropriate.

AP.VII.B.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation VII. Emergency Operations › Task C.

Task C. Powerplant(s) Failure (Simulated) during Takeoff While in Semi-Wing-Borne Flight

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with indications and pilot actions after powerplant(s) failure during takeoff while in semi-wing-borne flight in a multi-powerplant aircraft.

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Note: This can be initiated during the takeoff roll in wheeled aircraft or during the transition to wing-borne flight following a vertical takeoff.

Knowledge: The applicant demonstrates understanding of:

Area of Operation VII. Emergency Operations

AP.VII.C.K1 The procedures used during a powerplant(s) failure on takeoff, the appropriate reference airspeeds, and the specific pilot actions required.

AP.VII.C.K2 Operational considerations to include: aircraft performance (e.g., sideslip, bank angle, etc.), takeoff warning systems, runway length, surface conditions, density altitude, wake turbulence, environmental conditions, obstructions, and other related factors that could adversely affect safety.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VII.C.R1 Powerplant(s) failure.

AP.VII.C.R2 Reaction to the loss of power from one or more powerplants.

AP.VII.C.R3 Deceleration in a space-limited environment.

AP.VII.C.R4 Windshear.

AP.VII.C.R5 Dividing attention inside and outside the aircraft.

AP.VII.C.R6 Runway incursion.

AP.VII.C.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

AP.VII.C.R8 Abnormal operations, including planning for.

AP.VII.C.R8a a. Rejected takeoff

AP.VII.C.R8b b. Powerplant failure in takeoff/climb phase of flight

AP.VII.C.R9 Energy management.

Skills: The applicant exhibits the skill to:

AP.VII.C.S1 Recognize that a powerplant failure has occurred while performing a rolling takeoff.

AP.VII.C.S2 Input the appropriate flight control(s) and configure the aircraft for maximum deceleration.

AP.VII.C.S3 Maintain the operating powerplant(s) within acceptable operating limits.

AP.VII.C.S4 Land the aircraft, as appropriate to the scenario presented by the evaluator.

AP.VII.C.S5 Apply braking as appropriate.

AP.VII.C.S6 Refer to the checklist to ensure that the emergency procedure was followed correctly.

AP.VII.C.S7 Make radio calls as appropriate.

AP.VII.C.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation VII. Emergency Operations › Task D.

Task D. Inflight Powerplant(s) Failure and Restart in Multi-Powerplant Aircraft

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with an inflight powerplant(s) failure and restart, if applicable, in a multi-powerplant powered-lift aircraft.

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

Area of Operation VII. Emergency Operations

AP.VII.D.K1 Flight characteristics and controllability associated with maneuvering the aircraft with powerplant(s) inoperative, including the importance of drag reduction and appropriate aircraft configuration.

AP.VII.D.K2 Aircraft/powerplant limitations.

AP.VII.D.K3 Powerplant restart procedures and conditions where a restart attempt is appropriate.

AP.VII.D.K4 Causes of asymmetric thrust conditions and appropriate responses.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VII.D.R1 Potential powerplant(s) failure during flight.

AP.VII.D.R2 Following checklist procedures for a powerplant(s) failure or a powerplant(s) restart.

AP.VII.D.R3 Identifying the powerplant(s) that failed.

AP.VII.D.R4 Collision hazards.

AP.VII.D.R5 Aircraft configuration.

AP.VII.D.R6 Factors and situations that could lead to loss of control with an inflight powerplant(s) failure.

AP.VII.D.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

AP.VII.D.S1 Recognize and correctly identify powerplant(s) failure, complete memory items (if applicable), and maintain positive aircraft control.

AP.VII.D.S2 Coordinate with crew, if applicable, and complete the appropriate emergency procedures and checklist(s) for powerplant shutdown.

AP.VII.D.S3 Use flight controls and configure the aircraft in the proper combination as recommended by the manufacturer, or as required, to maintain best performance, and trim as required.

AP.VII.D.S4 Determine the cause for the powerplant(s) failure and if a restart is a viable option.

AP.VII.D.S5 Maintain the operating powerplant(s) within acceptable operating limits.

AP.VII.D.S6 Maintain the airspeed ±10 knots, the specified heading ±10°, and altitude ±100 feet as specified by the evaluator and within the aircraft’s capability.

AP.VII.D.S7 Consider a powerplant restart and, if appropriate, demonstrate the powerplant restart procedures in accordance with the manufacturer or operator specified procedures and checklists.

AP.VII.D.S8 Select the nearest suitable airport or landing area.

AP.VII.D.S9 Communicate with air traffic control (ATC) and the evaluator, as appropriate for the situation.

AP.VII.D.S10 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation VII. Emergency Operations › Task E. Approach and Landing with Powerplant(s) Failure (Simulated)

Task E. Approach and Landing with Powerplant(s) Failure (Simulated)

References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with approach and landing with simulated powerplant(s) failure.

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements &

Area of Operation VII. Emergency Operations

Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.VII.E.K1 Flight characteristics and controllability associated with maneuvering to a landing with inoperative powerplant(s).

AP.VII.E.K2 Effects of atmospheric conditions on emergency approach and landing.

AP.VII.E.K3 Air traffic control (ATC) services to aircraft in distress.

AP.VII.E.K4 Appropriate approach and landing profiles and aircraft configurations.

AP.VII.E.K5 Causes of asymmetric thrust conditions and appropriate responses.

AP.VII.E.K6 Go-around/rejected landing procedures with a powerplant failure.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VII.E.R1 Planning for a powerplant failure inflight or during an approach.

AP.VII.E.R2 Planning and following a flightpath to the selected landing area.

AP.VII.E.R3 Collision hazards.

AP.VII.E.R4 Flight control input(s).

AP.VII.E.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

AP.VII.E.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

AP.VII.E.R7 Performing a go-around/rejected landing with a powerplant failure.

Skills: The applicant exhibits the skill to:

AP.VII.E.S1 Recognize and correctly identify powerplant(s) failure, complete memory items (if applicable), and maintain positive aircraft control.

AP.VII.E.S2 Follow the manufacturer’s recommended emergency procedures and complete the appropriate checklist.

AP.VII.E.S3 Use flight controls and configure the aircraft as required to maintain best performance or as recommended by the manufacturer.

AP.VII.E.S4 Maintain the operating powerplant(s) within acceptable operating limits.

AP.VII.E.S5 Communicate with air traffic control (ATC) and the evaluator, as appropriate for the situation.

AP.VII.E.S6 Proceed toward the nearest suitable airport or landing area.

AP.VII.E.S7 Prior to beginning the final approach segment, maintain the desired altitude ±100 feet, the desired airspeed ±10 knots, the desired heading ±5°, and accurately track courses, radials, and bearings.

AP.VII.E.S8 Establish the recommended approach and landing configuration and airspeed, ±5 knots, and adjust pitch attitude and power as required to maintain a stabilized approach.

AP.VII.E.S9 Maintain directional control and appropriate crosswind correction throughout the approach and landing.

AP.VII.E.S10 Coordinate with crew, if applicable, and complete after landing checklists.

Area of Operation VII. Emergency Operations

Area of Operation VII. Emergency Operations › Task F.

Task F. Precision Approach (Manually Flown) with Powerplant(s) Failure (Simulated)

References: FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-16, FAA-H-8083-25; Flight Manual; Terminal Procedures Publications

Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a precision approach (manually flown) with powerplant(s) failure (simulated).

Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

AP.VII.F.K1 Flight characteristics and controllability associated with maneuvering to a landing with inoperative powerplant(s).

AP.VII.F.K2 Missed approach considerations with a powerplant failure.

AP.VII.F.K3 How to determine a suitable landing location.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

AP.VII.F.R1 Planning for a powerplant failure inflight or during an approach.

AP.VII.F.R2 Collision hazards.

AP.VII.F.R3 Aircraft configuration.

AP.VII.F.R4 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

AP.VII.F.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

AP.VII.F.R6 Landing with a powerplant failure.

AP.VII.F.R7 Missed approach with a powerplant failure.

AP.VII.F.R8 Maneuvering in instrument meteorological conditions (IMC) with a powerplant failure.

Skills: The applicant exhibits the skill to:

AP.VII.F.S1 Recognize and correctly identify powerplant(s) failure, complete memory items (if applicable), and maintain positive aircraft control.

AP.VII.F.S2 Complete the appropriate emergency procedures and checklist(s).

AP.VII.F.S3 Use flight controls in the proper combination as recommended by the manufacturer, or as required to maintain best performance, and trim as required.

AP.VII.F.S4 Maintain the operating powerplant(s) within acceptable operating limits.

AP.VII.F.S5 Notify/coordinate with air traffic control (ATC) or evaluator instructions as required.

Continue reading ↓ 120 of 189 passages shown