FAA-S-ACS-13 Private Pilot for Powered-Lift Category Airman Certification Standards
Private Pilot for Powered-Lift Category
Airman Certification Standards
FAA-S-ACS-13
Flight Standards Service
Washington, DC 20591
November 2023
Private Pilot for Powered-Lift Category ACS (FAA-S-ACS-13) i
Foreword
The U.S. Department of Transportation, Federal Aviation Administration (FAA), Office of Safety Standards, Regulatory Support Division, Airman Testing Standards Branch, has published the Private Pilot for Powered-Lift Category Airman Certification Standards (ACS) to communicate the aeronautical knowledge, risk management, and flight proficiency standards for private pilot certification in the powered-lift category.
This ACS is available for download, in PDF format, from www.faa.gov.
Comments regarding this ACS may be emailed to [email protected].
The FAA created FAA-G-ACS-2, Airman Certification Standards Companion Guide for Pilots, to provide guidance considered relevant and useful to the community. The number of appendices in the ACS was reduced and much of the non-regulatory material was moved to the Airman Certification Standards Companion Guide for Pilots. Applicants, instructors, and evaluators should consult this companion guide to familiarize themselves with ACS procedures. FAA-G-ACS-2 is available for download, in PDF format, from www.faa.gov.
Private Pilot for Powered-Lift Category ACS (FAA-S-ACS-13) ii
Table of Contents
Introduction
Airman Certification Standards Concept … 1 Use of the Term “Flight Manual” … 1
Area of Operation I. Preflight Preparation
Task A. Pilot Qualifications … 2 Task B. Airworthiness Requirements … 2 Task C. Weather Information … 3 Task D. Cross-Country Flight Planning … 4 Task E. National Airspace System … 5 Task F. Performance and Limitations … 6 Task G. Operation of Systems … 7 Task H. Human Factors … 8
Area of Operation II. Preflight Procedures
Task A. Preflight Assessment … 10 Task B. Flight Deck Management … 10 Task C. Powerplant Starting … 11 Task D. Ground Taxiing … 12 Task E. Before Takeoff Check … 13
Area of Operation III. Airport and Heliport Operations
Task A. Communications, Light Signals, and Runway Lighting Systems … 15 Task B. Runway/Taxiway/Heliport/Helipad Signs, Markings, and Lighting … 15 Task C. Traffic Patterns … 16
Area of Operation IV. Hovering Maneuvers
Task A. Vertical Takeoff and Landing … 18 Task B. Hover Taxi … 18 Task C. Air Taxi … 20
Area of Operation V. Takeoffs, Landings, and Go-Arounds
Task A. Normal Takeoff and Climb from a Hover … 22 Task B. Rolling Takeoff and Climb … 23 Task C. Maximum Performance Takeoff and Climb … 24 Task D. Normal Approach to a Hover … 25 Task E. Normal Approach and Landing … 27 Task F. Steep Approach and Landing … 28
Private Pilot for Powered-Lift Category ACS (FAA-S-ACS-13) iii
Table of Contents
Task G. Running/Roll-On Landing … 29 Task H. Confined Area Operations … 30 Task I. Slope Operations … 32 Task J. Pinnacle Operations … 33 Task K. Go-Around/Rejected Landing … 34
Area of Operation VI. Performance Maneuvers
Task A. Rapid Deceleration/Quick Stop … 36 Task B. Inflight Conversion During Straight-and-Level Flight … 36 Task C. Steep Turns … 37
Area of Operation VII. Ground Reference Maneuvers
Task A. Ground Reference Maneuvers … 39
Area of Operation VIII. Navigation
Task A. Pilotage and Dead Reckoning … 40 Task B. Navigation Systems and Radar Services … 41 Task C. Diversion … 42 Task D. Lost Procedures … 42
Area of Operation IX. Slow Flight and Stalls
Task A. Maneuvering During Slow Flight (Wing-Borne Configuration) … 44 Task B. Power-Off Stalls … 44 Task C. Power-On Stalls … 46
Area of Operation X. Basic Instrument Maneuvers
Task A. Straight-and-Level Flight … 48 Task B. Constant Airspeed Climbs … 48 Task C. Constant Airspeed Descents … 49 Task D. Turns to Headings … 50 Task E. Recovery from Unusual Flight Attitudes … 51 Task F. Radio Communications, Navigation Systems/Facilities, and Radar Services … 52
Area of Operation XI. Emergency Operations
Task A. Powerplant(s) Failure (Simulated) during Takeoff in Thrust-Borne Flight … 53 Task B. Powerplant(s) Failure (Simulated) during Takeoff While in Semi-Wing-Borne Flight … 54 Task C. Inflight Powerplant(s) Failure and Restart in Multi-Powerplant Aircraft … 55 Task D. Vortex Ring State (VRS) Avoidance … 56 Task E. Approach and Landing with Powerplant(s) Failure (Simulated) … 56 Task F. Emergency Descent … 57 Task G. Emergency Equipment and Survival Gear … 58
Private Pilot for Powered-Lift Category ACS (FAA-S-ACS-13) iv
Table of Contents
Task H. Systems and Equipment Malfunctions … 59 Task I. Dynamic Rollover … 60
Area of Operation XII. Night Operations
Task A. Night Operations … 61
Area of Operation XIII. Postflight Procedures
Task A. After Landing, Parking, and Securing … 62
Appendix 1: Practical Test Roles, Responsibilities, and Outcomes
Eligibility Requirements for a Private Pilot Certificate … 64 Use of the ACS During a Practical Test … 64 Combined Private/Instrument Test … 65 Instructor Responsibilities … 65
Evaluator Responsibilities … 65 Possible Outcomes of the Test … 66 Additional Rating Task Table … 67 Addition of a Powered-Lift Rating to an Existing Private Pilot Certificate … 68
Appendix 2: Safety of Flight
General … 69 Stall, Spin, Angle of Attack Awareness … 69 Use of Checklists … 69 Positive Exchange of Flight Controls … 69 Use of Distractions … 69 Aeronautical Decision-Making, Risk Management, Crew Resource Management, and Single-Pilot
Resource Management … 69 Multi-Powerplant Considerations … 70
Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations
Aircraft Requirements & Limitations … 71 Equipment Requirements & Limitations … 71 Use of Flight Simulation Training Devices (FSTD) … 71 Credit for Pilot Time in an FSTD … 71 Use of Aviation Training Devices (ATD) … 71 Credit for Pilot Time in an ATD … 71 Operational Requirements, Limitations, & Task Information … 72
Introduction › Airman Certification Standards Concept
Introduction
Airman Certification Standards Concept
The goal of the airman certification process is to ensure the applicant possesses the knowledge, ability to manage risks, and skill consistent with the privileges of the certificate or rating being exercised, in order to act as pilot-in-command (PIC).
Safe operations in today’s National Airspace System (NAS) require the integration of aeronautical knowledge, risk management, and flight proficiency standards. To accomplish these goals, the FAA drew upon the expertise of organizations and individuals across the aviation and training community to develop the ACS. The ACS integrates the elements of knowledge, risk management, and skill required for each airman certificate or rating. It thus forms a more comprehensive standard for what an applicant must know, consider, and do to demonstrate proficiency to pass the tests required for issuance of the applicable airman certificate or rating.
Introduction › Use of the Term “Flight Manual”
Use of the Term “Flight Manual”
Throughout this document, the term “flight manual” refers to the approved powered-lift aircraft flight manual.
Area of Operation I. Preflight Preparation
Area of Operation I. Preflight Preparation
Task A. Pilot Qualifications
References: 14 CFR parts 61, 68, 91; AC 68-1; FAA-H-8083-2, FAA-H-8083-25
Area of Operation I. Preflight Preparation › Task A. Pilot Qualifications
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal and emergency radio communications, air traffic control (ATC) light signals, and runway lighting systems.
Knowledge: The applicant demonstrates understanding of:
PL.I.A.K1 Certification requirements, recent flight experience, and recordkeeping.
PL.I.A.K2 Privileges and limitations.
PL.I.A.K3 Medical certificates: class, expiration, privileges, temporary disqualifications.
PL.I.A.K4 Documents required to exercise private pilot privileges.
PL.I.A.K5 Part 68 BasicMed privileges and limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.A.R1 Proficiency versus currency.
PL.I.A.R2 Flying unfamiliar aircraft or operating with unfamiliar flight display systems and avionics.
Skills: The applicant exhibits the skill to:
PL.I.A.S1 Apply requirements to act as pilot-in-command (PIC) under Visual Flight Rules (VFR) in a scenario given by the evaluator.
Area of Operation I. Preflight Preparation › Task B. Airworthiness Requirements
Task B. Airworthiness Requirements
References: 14 CFR parts 21, 39, 43, 91; FAA-H-8083-2, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with airworthiness requirements, including aircraft certificates.
Knowledge: The applicant demonstrates understanding of:
PL.I.B.K1 General airworthiness requirements and compliance for aircraft, including:
PL.I.B.K1a a. Location and expiration dates of required aircraft certificates
PL.I.B.K1b b. Required inspections and aircraft logbook documentation
PL.I.B.K1c c. Airworthiness Directives and Special Airworthiness Information Bulletins
PL.I.B.K1d d. Purpose and procedure for obtaining a special flight permit
PL.I.B.K1e e. Owner/Operator and pilot-in-command responsibilities
PL.I.B.K2 Pilot-performed preventive maintenance.
PL.I.B.K3 Equipment requirements for day and night VFR flight, including:
PL.I.B.K3a a. Flying with inoperative equipment
Area of Operation I. Preflight Preparation
PL.I.B.K3b b. Using an approved Minimum Equipment List (MEL)
PL.I.B.K3c c. Kinds of Operation Equipment List (KOEL)
PL.I.B.K3d d. Required discrepancy records or placards
PL.I.B.K4 Standard and special airworthiness certificates and their associated operational limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.B.R1 Inoperative equipment discovered prior to flight.
Skills: The applicant exhibits the skill to:
PL.I.B.S1 Locate and describe aircraft airworthiness and registration information.
PL.I.B.S2 Determine the aircraft is airworthy in the scenario given by the evaluator.
PL.I.B.S3 Apply appropriate procedures for operating with inoperative equipment in the scenario given by the evaluator.
Area of Operation I. Preflight Preparation › Task C. Weather Information
Task C. Weather Information
References: 14 CFR part 91; AC 91-92; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25, FAA-H-8083-28
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with weather information for a flight under VFR.
Note: If K2 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.
Note: If K3 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.
Knowledge: The applicant demonstrates understanding of:
PL.I.C.K1 Sources of weather data (e.g., National Weather Service, Flight Service) for flight planning purposes.
PL.I.C.K2 Acceptable weather products and resources required for preflight planning, current and forecast weather for departure, en route, and arrival phases of flight such as:
PL.I.C.K2a a. Airport Observations (METAR and SPECI) and Pilot Observations (PIREP)
PL.I.C.K2b b. Surface Analysis Chart, Ceiling and Visibility Chart (CVA)
PL.I.C.K2c c. Terminal Aerodrome Forecasts (TAF)
PL.I.C.K2d d. Graphical Forecasts for Aviation (GFA)
PL.I.C.K2e e. Wind and Temperature Aloft Forecast (FB)
PL.I.C.K2f f. Convective Outlook (AC)
PL.I.C.K2g g. Inflight Aviation Weather Advisories including Airmen's Meteorological Information (AIRMET),
Significant Meteorological Information (SIGMET), and Convective SIGMET
PL.I.C.K3 Meteorology applicable to the departure, en route, alternate, and destination under visual flight rules (VFR) in Visual Meteorological Conditions (VMC), including expected climate and hazardous conditions such as:
PL.I.C.K3a a. Atmospheric composition and stability
PL.I.C.K3b b. Wind (e.g., windshear, mountain wave, factors affecting wind, etc.)
Area of Operation I. Preflight Preparation
PL.I.C.K3c c. Temperature and heat exchange
PL.I.C.K3d d. Moisture/precipitation
PL.I.C.K3e e. Weather system formation, including air masses and fronts
PL.I.C.K3f f. Clouds
PL.I.C.K3g g. Turbulence
PL.I.C.K3h h. Thunderstorms and microbursts
PL.I.C.K3i i. Icing and freezing level information
PL.I.C.K3j j. Fog/mist
PL.I.C.K3k k. Frost
PL.I.C.K3l l. Obstructions to visibility (e.g., smoke, haze, volcanic ash, etc.)
PL.I.C.K4 Flight deck instrument displays of digital weather and aeronautical information.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.C.R1 Making the go/no-go and continue/divert decisions, including:
PL.I.C.R1a a. Circumstances that would make diversion prudent
PL.I.C.R1b b. Personal weather minimums
PL.I.C.R1c c. Hazardous weather conditions, including known or forecast icing or turbulence aloft
PL.I.C.R2 Use and limitations of:
PL.I.C.R2a a. Installed onboard weather equipment
PL.I.C.R2b b. Aviation weather reports and forecasts
PL.I.C.R2c c. Inflight weather resources
Skills: The applicant exhibits the skill to:
PL.I.C.S1 Use available aviation weather resources to obtain an adequate weather briefing.
PL.I.C.S2 Analyze the implications of at least three of the conditions listed in K3a through K3l, using actual weather or weather conditions provided by the evaluator.
PL.I.C.S3 Correlate weather information to make a go/no-go decision.
Area of Operation I. Preflight Preparation › Task D. Cross-Country Flight Planning
Task D. Cross-Country Flight Planning
References: 14 CFR part 91; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; NOTAMs; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with cross-country flights and VFR flight planning.
Note: Preparation, presentation, and explanation of a computer-generated flight plan is an acceptable option.
Knowledge: The applicant demonstrates understanding of:
Area of Operation I. Preflight Preparation
PL.I.D.K1 Route planning, including consideration of different classes and special use airspace (SUA) and selection of appropriate and available navigation/communication systems and facilities.
PL.I.D.K1a a. Use of an electronic flight bag (EFB), if used
PL.I.D.K2 Altitude selection accounting for terrain and obstacles, glide or autorotative distance of the aircraft, VFR cruising altitudes, and the effect of wind.
PL.I.D.K3 Calculating:
PL.I.D.K3a a. Time, climb and descent rates, course, distance, heading, true airspeed, and groundspeed
PL.I.D.K3b b. Estimated time of arrival, including conversion to universal coordinated time (UTC)
PL.I.D.K3c c. Fuel requirements, including reserve
PL.I.D.K4 Elements of a VFR flight plan.
PL.I.D.K5 Procedures for filing, activating, and closing a VFR flight plan.
PL.I.D.K6 Inflight intercept procedures.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.D.R1 Pilot.
PL.I.D.R2 Aircraft.
PL.I.D.R3 Environment (e.g., weather, airports, airspace, terrain, obstacles, including wire strike hazards).
PL.I.D.R4 External pressures.
PL.I.D.R5 Limitations of air traffic control (ATC) services.
PL.I.D.R6 Fuel planning.
PL.I.D.R7 Use of an electronic flight bag (EFB), if used.
Skills: The applicant exhibits the skill to:
PL.I.D.S1 Prepare, present, and explain a cross-country flight plan assigned by the evaluator, including a risk analysis based on real-time weather, to the first fuel stop.
PL.I.D.S2 Apply pertinent information from appropriate and current aeronautical charts, Chart Supplements; Notices to Air Missions (NOTAMs) relative to airport/heliport/helipad/landing area, runway and taxiway closures; and other flight publications.
PL.I.D.S3 Create a navigation log and prepare a VFR flight plan.
PL.I.D.S4 Recalculate fuel reserves based on a scenario provided by the evaluator.
PL.I.D.S5 Use an electronic flight bag (EFB), if applicable.
Area of Operation I. Preflight Preparation › Task E. National Airspace System
Task E. National Airspace System
References: 14 CFR parts 71, 91, 93; AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with National Airspace System (NAS) operations under VFR as a private pilot.
Knowledge: The applicant demonstrates understanding of:
Area of Operation I. Preflight Preparation
PL.I.E.K1 Airspace classes and associated requirements and limitations.
PL.I.E.K2 Chart symbols.
PL.I.E.K3 Special use airspace (SUA), special flight rules areas (SFRA), temporary flight restrictions (TFR), and other airspace areas.
PL.I.E.K4 Special visual flight rules (VFR) requirements.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.E.R1 Various classes and types of airspace.
Skills: The applicant exhibits the skill to:
PL.I.E.S1 Identify and comply with the requirements for basic VFR weather minimums and flying in particular classes of airspace.
PL.I.E.S2 Correctly identify airspace and operate in accordance with associated communication and equipment requirements.
PL.I.E.S3 Identify the requirements for operating in SUA or within a TFR. Identify and comply with special air traffic rules (SATR) and SFRA operations, if applicable.
Area of Operation I. Preflight Preparation › Task F. Performance and Limitations
Task F. Performance and Limitations
References: FAA-H-8083-1, FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with operating an aircraft within the parameters of its performance capabilities and limitations.
Knowledge: The applicant demonstrates understanding of:
PL.I.F.K1 Elements related to performance and limitations by explaining the use of charts, tables, and data to determine performance.
PL.I.F.K2 Factors affecting performance, including:
PL.I.F.K2a a. Atmospheric conditions
PL.I.F.K2b b. Pilot technique
PL.I.F.K2c c. Aircraft configuration
PL.I.F.K2d d. Airport, heliport, helipad, or unprepared surface environment
PL.I.F.K2e e. Loading [e.g., center of gravity (CG)]
PL.I.F.K2f f. Weight and balance
PL.I.F.K3 Aerodynamics.
PL.I.F.K4 Height/Velocity (H/V) diagram according to the flight manual.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.F.R1 Use of performance charts, tables, and data.
Area of Operation I. Preflight Preparation
PL.I.F.R2 Aircraft limitations.
PL.I.F.R3 Possible differences between calculated performance and actual performance.
PL.I.F.R4 Operations within “avoid areas” of the H/V diagram.
PL.I.F.R5 Other hazards specific to the powered-lift make and model.
Skills: The applicant exhibits the skill to:
PL.I.F.S1 Compute the weight and balance, correct out-of-center of gravity loading errors and determine if the weight and balance remains within limits during all phases of flight and aircraft configurations.
PL.I.F.S2 Use of the appropriate manufacturer’s approved performance charts, tables, and data.
Area of Operation I. Preflight Preparation › Task G. Operation of Systems
Task G. Operation of Systems
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with safe operation of systems on the aircraft provided for the flight test.
Note: If K1 is selected, the evaluator must assess the applicant's knowledge of at least three sub-elements.
Knowledge: The applicant demonstrates understanding of:
PL.I.G.K1 Aircraft systems, including:
PL.I.G.K1a a. Primary flight controls
PL.I.G.K1b b. Secondary flight controls
PL.I.G.K1c c. Powerplant(s) and means of producing thrust
PL.I.G.K1d d. Landing gear
PL.I.G.K1e e. Fuel, oil, and hydraulic
PL.I.G.K1f f. Electrical
PL.I.G.K1g g. Avionics
PL.I.G.K1h h. Pitot-static, vacuum/pressure, and associated flight instruments
PL.I.G.K1i i. Environmental
PL.I.G.K1j j. Deicing and anti-icing
PL.I.G.K1k k. Oxygen system
PL.I.G.K1l l. Gearboxes, drive shafts, transmission systems, as applicable
PL.I.G.K1m m. Battery(s) used for propulsion–charging, discharging, and condition, as applicable
PL.I.G.K2 Indications of and procedures for managing system abnormalities or failures.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.G.R1 Detection of system malfunctions or failures.
PL.I.G.R2 Management of a system failure.
Area of Operation I. Preflight Preparation
PL.I.G.R3 Monitoring and management of automated systems.
Skills: The applicant exhibits the skill to:
PL.I.G.S1 Operate at least three of the systems listed in K1a through K1m appropriately.
PL.I.G.S2 Complete the appropriate checklist(s).
Area of Operation I. Preflight Preparation › Task H. Human Factors
Task H. Human Factors
References: AIM; FAA-H-8083-2, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with personal health, flight physiology, and aeromedical and human factors related to safety of flight.
Knowledge: The applicant demonstrates understanding of:
PL.I.H.K1 Symptoms, recognition, causes, effects, and corrective actions associated with aeromedical and physiological issues, including:
PL.I.H.K1a a. Hypoxia
PL.I.H.K1b b. Hyperventilation
PL.I.H.K1c c. Middle ear and sinus problems
PL.I.H.K1d d. Spatial disorientation
PL.I.H.K1e e. Motion sickness
PL.I.H.K1f f. Carbon monoxide poisoning
PL.I.H.K1g g. Stress
PL.I.H.K1h h. Fatigue
PL.I.H.K1i i. Dehydration and nutrition
PL.I.H.K1j j. Hypothermia
PL.I.H.K1k k. Optical illusions
PL.I.H.K1l l. Dissolved nitrogen in the bloodstream after scuba dives
PL.I.H.K2 Regulations regarding use of alcohol and drugs.
PL.I.H.K3 Effects of alcohol, drugs, and over-the-counter medications.
PL.I.H.K4 Aeronautical Decision-Making (ADM) to include using Crew Resource Management (CRM) or Single- Pilot Resource Management (SRM), as appropriate.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.I.H.R1 Aeromedical and physiological issues.
PL.I.H.R2 Hazardous attitudes.
PL.I.H.R3 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.I.H.R4 Confirmation and expectation bias.
Area of Operation I. Preflight Preparation
Skills: The applicant exhibits the skill to:
PL.I.H.S1 Associate the symptoms and effects for at least three of the conditions listed in K1a through K1l with the cause(s) and corrective action(s).
PL.I.H.S2 Perform self-assessment, including fitness for flight and personal minimums, for actual flight or a scenario given by the evaluator.
Area of Operation II. Preflight Procedures › Task A. Preflight Assessment
Area of Operation II. Preflight Procedures
Area of Operation II. Preflight Procedures
Task A. Preflight Assessment
References: FAA-H-8083-2, FAA-H-8083-25, FAA-H-8083-28; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with preparation for safe flight.
Knowledge: The applicant demonstrates understanding of:
PL.II.A.K1 Pilot self-assessment.
PL.II.A.K2 Determining that the aircraft to be used is airworthy.
PL.II.A.K3 Aircraft preflight inspection, including:
PL.II.A.K3a a. Which items should be inspected
PL.II.A.K3b b. The reasons for checking each item
PL.II.A.K3c c. How to detect possible defects
PL.II.A.K3d d. The associated regulations
PL.II.A.K4 Environmental factors, including weather, terrain, route selection, and obstructions.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.II.A.R1 Pilot.
PL.II.A.R2 Aircraft.
PL.II.A.R3 Environment (e.g., weather, icing, airports/heliports/helipads/landing areas, airspace, terrain, obstacles).
PL.II.A.R4 External pressures.
PL.II.A.R5 Aviation security concerns.
Skills: The applicant exhibits the skill to:
PL.II.A.S1 Inspect the aircraft with reference to an appropriate checklist.
PL.II.A.S2 Verify the aircraft is in condition for safe flight and conforms to its type design.
PL.II.A.S3 Perform self-assessment.
PL.II.A.S4 Continue to assess the environment for safe flight.
Area of Operation II. Preflight Procedures › Task B. Flight Deck Management
Task B. Flight Deck Management
References: 14 CFR part 91; AC 120-71; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight deck management practices.
Note: See Appendix 2: Safety of Flight.
Knowledge: The applicant demonstrates understanding of:
Area of Operation II. Preflight Procedures
PL.II.B.K1 Passenger briefing requirements, including operation and required use of safety restraint systems.
PL.II.B.K2 Use of appropriate checklists.
PL.II.B.K3 Requirements for current and appropriate navigation data.
PL.II.B.K4 Securing items and cargo.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.II.B.R1 Use of systems or equipment, including automation and portable electronic devices.
PL.II.B.R2 Inoperative equipment.
PL.II.B.R3 Passenger distractions.
Skills: The applicant exhibits the skill to:
PL.II.B.S1 Secure all items in the aircraft.
PL.II.B.S2 Conduct an appropriate passenger briefing, including identifying the pilot-in-command (PIC), use of safety belts, shoulder harnesses, doors, sterile aircraft, passenger conduct and avoidance of rotor or air induction systems, powerplants, and other heat sources, and emergency procedures.
PL.II.B.S3 Properly program and manage the aircraft’s automation, as applicable.
PL.II.B.S4 Appropriately manage risks by utilizing ADM, including SRM/CRM.
Area of Operation II. Preflight Procedures › Task C. Powerplant Starting
Task C. Powerplant Starting
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with recommended powerplant starting procedures.
Knowledge: The applicant demonstrates understanding of:
PL.II.C.K1 Starting under various conditions.
PL.II.C.K2 Starting the powerplant(s) by use of external power.
PL.II.C.K3 Limitations associated with starting.
PL.II.C.K4 Conditions leading to and procedures for an aborted start.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.II.C.R1 Use of external power unit.
PL.II.C.R2 Limitations during starting.
PL.II.C.R3 Other hazards specific to the powered-lift make and model.
Skills: The applicant exhibits the skill to:
PL.II.C.S1 Position the aircraft properly considering structures, other aircraft, wind, and the safety of nearby persons and property.
Area of Operation II. Preflight Procedures
PL.II.C.S2 Complete the appropriate checklist(s).
PL.II.C.S3 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.
PL.II.C.S4 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation II. Preflight Procedures › Task D. Ground Taxiing
Task D. Ground Taxiing
References: AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with ground taxi operations, in a wheel-type aircraft, including runway incursion avoidance.
Knowledge: The applicant demonstrates understanding of:
PL.II.D.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).
PL.II.D.K2 Taxi instructions/clearances.
PL.II.D.K3 Airport/heliport/helipad/landing area, signs, markings, and lighting.
PL.II.D.K4 Visual indicators for wind.
PL.II.D.K5 Aircraft lighting, as appropriate.
PL.II.D.K6 Procedures for:
PL.II.D.K6a a. Appropriate flight deck activities prior to taxi, including route planning and identifying the
location of Hot Spots
PL.II.D.K6b b. Aircraft configuration
PL.II.D.K6c c. Radio communications at towered and non-towered airports/heliports/helipads/landing areas
PL.II.D.K6d d. Entering or crossing runways
PL.II.D.K6e e. Night taxi operations
PL.II.D.K6f f. Taxi limitations
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.II.D.R1 Activities and distractions.
PL.II.D.R2 Confirmation or expectation bias as related to taxi instructions.
PL.II.D.R3 A taxi route or departure runway change.
PL.II.D.R4 Speed during taxi and turns.
PL.II.D.R5 Appropriate thrust vector and brake use.
PL.II.D.R6 Airframe and rotor clearances during taxi.
PL.II.D.R7 Runway incursion.
PL.II.D.R8 Other hazards specific to the powered-lift make and model.
Skills: The applicant exhibits the skill to:
Area of Operation II. Preflight Procedures
PL.II.D.S1 Receive and correctly read back clearances/instructions, if applicable.
PL.II.D.S2 Use an appropriate airport/heliport diagram or taxi chart, if published.
PL.II.D.S3 Position the flight controls and configure the aircraft for the existing wind conditions.
PL.II.D.S4 Complete the appropriate checklist(s).
PL.II.D.S5 Maintain positive control of the aircraft during ground operations by controlling direction and speed without excessive use of brakes.
PL.II.D.S6 Comply with airport/heliport/helipad/landing area taxiway markings, signals, and air traffic control (ATC) clearances and instructions.
PL.II.D.S7 Position the aircraft relative to hold lines or a specified point.
PL.II.D.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation II. Preflight Procedures › Task E. Before Takeoff Check
Task E. Before Takeoff Check
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with before takeoff check.
Knowledge: The applicant demonstrates understanding of:
PL.II.E.K1 Purpose of before takeoff checklist items, including:
PL.II.E.K1a a. Reasons for checking each item
PL.II.E.K1b b. Detecting malfunctions
PL.II.E.K1c c. Configuring the aircraft as recommended by the manufacturer
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.II.E.R1 Division of attention while conducting before takeoff checks.
PL.II.E.R2 Unexpected runway changes.
PL.II.E.R3 Unexpected or unclear clearances from ATC.
PL.II.E.R4 Wake turbulence.
PL.II.E.R5 Downwash.
PL.II.E.R6 Potential powerplant failure during takeoff or other malfunction considering operational factors such as aircraft characteristics, runway/takeoff path length, surface conditions, environmental conditions, and obstructions.
Skills: The applicant exhibits the skill to:
PL.II.E.S1 Review takeoff performance.
PL.II.E.S2 Select the appropriate takeoff profile for aircraft and environmental conditions.
PL.II.E.S3 Complete the appropriate checklist(s).
PL.II.E.S4 Properly position the aircraft considering other aircraft, vessels, and wind.
Area of Operation II. Preflight Procedures
PL.II.E.S5 Verify that powerplant parameters and aircraft configuration are suitable for the takeoff profile.
PL.II.E.S6 Divide attention inside and outside the aircraft.
PL.II.E.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation III. Airport and Heliport Operations › Task A. Communications, Light Signals, and Runway Lighting Systems
Area of Operation III. Airport and Heliport Operations
Area of Operation III. Airport and Heliport Operations
Task A. Communications, Light Signals, and Runway Lighting Systems
References: 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal and emergency radio communications, air traffic control (ATC) light signals, and runway lighting systems.
Knowledge: The applicant demonstrates understanding of:
PL.III.A.K1 How to obtain appropriate radio frequencies.
PL.III.A.K2 Proper radio communication procedures and air traffic control (ATC) phraseology.
PL.III.A.K3 ATC light signal recognition.
PL.III.A.K4 Appropriate use of transponder(s).
PL.III.A.K5 Lost communication procedures.
PL.III.A.K6 Equipment issues that could cause loss of communication.
PL.III.A.K7 Radar assistance.
PL.III.A.K8 National Transportation Safety Board (NTSB) accident/incident reporting.
PL.III.A.K9 Runway Status Lighting Systems.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.III.A.R1 Communication.
PL.III.A.R2 Deciding if and when to declare an emergency.
PL.III.A.R3 Use of non-standard phraseology.
Skills: The applicant exhibits the skill to:
PL.III.A.S1 Select and activate appropriate frequencies.
PL.III.A.S2 Transmit using standard phraseology and procedures as specified in the Aeronautical Information Manual (AIM) and Pilot/Controller Glossary.
PL.III.A.S3 Acknowledge radio communications and comply with ATC instructions or as directed by the evaluator.
Area of Operation III. Airport and Heliport Operations › Task B. Runway/Taxiway/Heliport/Helipad Signs, Markings, and Lighting
Task B. Runway/Taxiway/Heliport/Helipad Signs, Markings, and Lighting
References: 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with runway/taxiway/heliport/helipad signs, markings and lighting.
Knowledge: The applicant demonstrates understanding of:
PL.III.B.K1 Airport runway, heliport, helipad, taxiway signs, markings, and lighting.
PL.III.B.K2 Airport movement area.
Area of Operation III. Airport and Heliport Operations
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.III.B.R1 Interpretation of signs, markings, or lighting.
PL.III.B.R2 Landing site dimensions and limitations.
PL.III.B.R3 Conflict with aircraft, vehicles, and persons.
PL.III.B.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.III.B.R5 Powered-lift configuration, including the effect of thrust on other aircraft.
Skills: The applicant exhibits the skill to:
PL.III.B.S1 Comply with airport/heliport/helipad signs, markings, and lighting encountered, as applicable to the aircraft provided for the practical test.
Area of Operation III. Airport and Heliport Operations › Task C. Traffic Patterns
Task C. Traffic Patterns
References: 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with traffic patterns.
Knowledge: The applicant demonstrates understanding of:
PL.III.C.K1 Towered and nontowered airport/heliport/helipad/landing area operations and restrictions.
PL.III.C.K2 Runway selection and traffic pattern parameters for the current conditions.
PL.III.C.K3 Right-of-way rules.
PL.III.C.K4 Use of automated weather and airport/heliport information.
PL.III.C.K5 Aircraft configuration and selection for the traffic pattern in use.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.III.C.R1 Collision hazards.
PL.III.C.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.III.C.R3 Windshear and wake turbulence.
Skills: The applicant exhibits the skill to:
PL.III.C.S1 Identify and interpret airport/heliport/helipad/landing area runways, taxiways, markings, signs, and lighting.
PL.III.C.S2 Comply with recommended traffic pattern procedures.
PL.III.C.S3 Correct for wind drift to maintain the proper ground track.
PL.III.C.S4 Maintain orientation with the runway/landing area in use.
PL.III.C.S5 Maintain traffic pattern altitude, ±100 feet, and the appropriate airspeed, ±10 knots.
PL.III.C.S6 Maintain situational awareness and proper spacing from other aircraft in the traffic pattern.
Area of Operation III. Airport and Heliport Operations
PL.III.C.S7 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.
PL.III.C.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation IV. Hovering Maneuvers › Task A. Vertical Takeoff and Landing
Area of Operation IV. Hovering Maneuvers
Area of Operation IV. Hovering Maneuvers
Task A. Vertical Takeoff and Landing
References: 14 CFR part 91; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with vertical takeoff and landing from a hover.
Knowledge: The applicant demonstrates understanding of:
PL.IV.A.K1 Elements related to a vertical takeoff to a hover and landing from a hover.
PL.IV.A.K2 Appropriate aircraft configuration for a stationary hover.
PL.IV.A.K3 Effect of wind on flight control inputs.
PL.IV.A.K4 Ground effect.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.IV.A.R1 Obstacle and hazard avoidance.
PL.IV.A.R2 Dynamic rollover.
PL.IV.A.R3 Powerplant failure during hover.
PL.IV.A.R4 Downwash.
PL.IV.A.R5 Ground resonance.
Skills: The applicant exhibits the skill to:
PL.IV.A.S1 Complete the appropriate checklist(s).
PL.IV.A.S2 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.
PL.IV.A.S3 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.
PL.IV.A.S4 Ascend to and maintain recommended hovering altitude, and descend from recommended hovering altitude in headwind, crosswind, and tailwind conditions, without drift.
PL.IV.A.S5 Establish recommended hovering altitude, ±1/2 of that altitude within 10 feet of the surface; if above 10 feet, ±5 feet.
PL.IV.A.S6 Maintain position within ±4 feet of a designated point.
PL.IV.A.S7 Descend vertically to within 2 feet of the designated touchdown point.
PL.IV.A.S8 Maintain headings ±10°, as specified by the evaluator.
PL.IV.A.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation IV. Hovering Maneuvers › Task B. Hover Taxi
Task B. Hover Taxi
References: AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with hover taxi operations, including runway incursion avoidance.
Area of Operation IV. Hovering Maneuvers
Knowledge: The applicant demonstrates understanding of:
PL.IV.B.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).
PL.IV.B.K2 Hover taxi instructions, clearances, and limitations.
PL.IV.B.K3 Airport/heliport/helipad/landing area, signs, markings, and lighting.
PL.IV.B.K4 Visual indicators for wind.
PL.IV.B.K5 Aircraft lighting, as appropriate.
PL.IV.B.K6 Procedures for:
PL.IV.B.K6a a. Pilot activities during taxiing
PL.IV.B.K6b b. Safe hover taxi at towered and non-towered airports/heliports/helipads/landing areas
PL.IV.B.K6c c. Entering or crossing runways
PL.IV.B.K7 Aircraft configuration.
PL.IV.B.K8 Aircraft operating limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.IV.B.R1 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.IV.B.R2 Reduced visibility or night taxi operations.
PL.IV.B.R3 Powerplant(s) failure during hover taxi.
PL.IV.B.R4 Other aircraft and hazards.
PL.IV.B.R5 Hazardous effects of downwash.
PL.IV.B.R6 Aircraft configuration.
PL.IV.B.R7 Height/Velocity (H/V) considerations.
PL.IV.B.R8 Crosswind limitations.
PL.IV.B.R9 Other hazards specific to the powered-lift make and model.
PL.IV.B.R10 Runway incursion.
Skills: The applicant exhibits the skill to:
PL.IV.B.S1 Complete the appropriate checklist(s).
PL.IV.B.S2 Receive and correctly read back clearances/instructions, if applicable.
PL.IV.B.S3 Use an airport diagram or taxi chart during taxi, if published, and maintain situational awareness.
PL.IV.B.S4 Comply with airport/heliport taxiway markings, signals, and signs.
PL.IV.B.S5 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.
PL.IV.B.S6 Hover taxi over specified ground references, demonstrating forward, sideward, and rearward hovering and hovering turns.
Area of Operation IV. Hovering Maneuvers
PL.IV.B.S7 Maintain recommended hovering altitude, ±1/2 of that altitude within 10 feet of the surface, if above 10 feet, ±5 feet.
PL.IV.B.S8 Make 90°, 180°, and 360° pivoting turns, stopping within 10° of specified headings.
PL.IV.B.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation IV. Hovering Maneuvers › Task C. Air Taxi
Task C. Air Taxi
References: AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with air taxi operations.
Knowledge: The applicant demonstrates understanding of:
PL.IV.C.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).
PL.IV.C.K2 Air taxi instructions, clearances, and limitations.
PL.IV.C.K3 Aircraft configuration.
PL.IV.C.K4 Airport/heliport/helipad/landing area, signs, markings, and lighting.
PL.IV.C.K5 Visual indicators for wind.
PL.IV.C.K6 Aircraft lighting, as appropriate.
PL.IV.C.K7 Procedures for:
PL.IV.C.K7a a. Pilot activities during taxiing
PL.IV.C.K7b b. Safe air taxi at towered and non-towered airports/heliports/helipads/landing areas
PL.IV.C.K7c c. Overflying of runways
PL.IV.C.K8 Aircraft operating limitations.
PL.IV.C.K9 Appropriate height and speed for air taxi.
PL.IV.C.K10 Height/Velocity (H/V) considerations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.IV.C.R1 Activities and distractions.
PL.IV.C.R2 Reduced visibility or night taxi operations.
PL.IV.C.R3 H/V diagram performance in case of powerplant failure.
PL.IV.C.R4 Other aircraft and hazards.
PL.IV.C.R5 Runway incursion.
Skills: The applicant exhibits the skill to:
PL.IV.C.S1 Complete the appropriate checklist(s).
PL.IV.C.S2 Use an airport diagram or taxi chart during taxi, if published, and maintain situational awareness.
Area of Operation IV. Hovering Maneuvers
PL.IV.C.S3 Select a safe airspeed and altitude.
PL.IV.C.S4 Maintain an appropriate aircraft configuration throughout the maneuver.
PL.IV.C.S5 Maintain specified altitude, ±10 feet.
PL.IV.C.S6 Air taxi from one point to another under various wind conditions.
PL.IV.C.S7 Maintain the aircraft within operating limits throughout the maneuver.
PL.IV.C.S8 Comply with airport/heliport/helipad/landing area markings, lights, signs, and ATC instructions.
PL.IV.C.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task A. Normal Takeoff and Climb from a Hover
Area of Operation V. Takeoffs, Landings, and Go-Arounds
Area of Operation V. Takeoffs, Landings, and Go-Arounds
Note: Select all applicable tasks in accordance with the aircraft's operating characteristics as specified in the flight manual.
Task A. Normal Takeoff and Climb from a Hover
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal takeoff and climb from a hover.
Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.
Knowledge: The applicant demonstrates understanding of:
PL.V.A.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.
PL.V.A.K2 Recommended takeoff and climb profiles.
PL.V.A.K3 Aircraft configuration.
PL.V.A.K4 Factors affecting the profile of the height/velocity (H/V) diagram.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.A.R1 Selection of helipad/deck, runway, or departure point based on aircraft performance and limitations, available distance, and wind.
PL.V.A.R2 Effects of:
PL.V.A.R2a a. Crosswind
PL.V.A.R2b b. Windshear
PL.V.A.R2c c. Tailwind
PL.V.A.R2d d. Wake turbulence
PL.V.A.R2e e. Runway/departure point surface/condition
PL.V.A.R2f f. Aircraft weight
PL.V.A.R3 Abnormal operations including:
PL.V.A.R3a a. Rejected takeoff
PL.V.A.R3b b. Powerplant failure in hover/takeoff/climb phase of flight
PL.V.A.R4 Collision hazards.
PL.V.A.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
PL.V.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.V.A.R7 Runway incursion.
Skills: The applicant exhibits the skill to:
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.A.S1 Complete the appropriate checklist(s).
PL.V.A.S2 Make radio calls as appropriate.
PL.V.A.S3 Verify assigned/correct runway, if at an airport.
PL.V.A.S4 Determine wind direction with or without visible wind direction indicators.
PL.V.A.S5 Position the flight controls and configure the aircraft for the existing wind conditions.
PL.V.A.S6 Clear the area, ground or hover taxi into takeoff position, and hover the aircraft above the departure point, aligned with the departure path.
PL.V.A.S7 Confirm takeoff power and instrument indications prior to forward movement.
PL.V.A.S8 Takeoff and accelerate to the manufacturer’s recommended speed.
PL.V.A.S9 After takeoff, establish and maintain a positive rate of climb and configure aircraft, as appropriate.
PL.V.A.S10 Maintain the aircraft within operating limits throughout the maneuver.
PL.V.A.S11 Maintain VY ±10 knots to a safe maneuvering altitude.
PL.V.A.S12 Maintain directional control and proper wind-drift correction throughout takeoff and climb.
PL.V.A.S13 Comply with noise abatement procedures, as applicable.
PL.V.A.S14 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task B. Rolling Takeoff and Climb
Task B. Rolling Takeoff and Climb
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with rolling takeoff with wheel-type landing gear.
Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.
Knowledge: The applicant demonstrates understanding of:
PL.V.B.K1 Elements related to a rolling takeoff and the purpose of the maneuver.
PL.V.B.K2 Aircraft configurations.
PL.V.B.K3 Effects of wind, weight, temperature, and density altitude.
PL.V.B.K4 Translational lift.
PL.V.B.K5 Takeoff and climb performance and the height velocity (H/V) diagram.
PL.V.B.K6 Aircraft performance and limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.B.R1 Collision hazards.
PL.V.B.R2 Powerplant failure during rolling takeoff and climb out.
PL.V.B.R3 Aircraft configuration.
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.B.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.V.B.R5 Effects of:
PL.V.B.R5a a. Crosswind
PL.V.B.R5b b. Windshear
PL.V.B.R5c c. Tailwind
PL.V.B.R5d d. Wake turbulence
PL.V.B.R5e e. Runway/departure point surface/condition
PL.V.B.R5f f. Aircraft weight
PL.V.B.R6 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
Skills: The applicant exhibits the skill to:
PL.V.B.S1 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.
PL.V.B.S2 Complete the appropriate checklist(s).
PL.V.B.S3 Configure the aircraft correctly regarding environmental conditions and aircraft loading.
PL.V.B.S4 Maintain the aircraft within operating limits throughout the maneuver.
PL.V.B.S5 Maintain proper ground track with crosswind correction, if necessary.
PL.V.B.S6 Maintain a positive rate of climb.
PL.V.B.S7 Transition to recommended climb airspeed ±10 knots.
PL.V.B.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.V.B.S9 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task C. Maximum Performance Takeoff and Climb
Task C. Maximum Performance Takeoff and Climb
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with maximum performance takeoff and climb.
Knowledge: The applicant demonstrates understanding of:
PL.V.C.K1 Situations where this maneuver is appropriate.
PL.V.C.K2 Effects of atmospheric conditions, including wind and temperature, on takeoff and climb performance.
PL.V.C.K3 Appropriate aircraft configuration, takeoff, and climb profiles.
PL.V.C.K4 Factors affecting the profile of the height/velocity (H/V) diagram.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.C.R1 Selection of takeoff path based on aircraft performance and limitations, available distance, and wind.
PL.V.C.R2 Effects of:
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.C.R2a a. Crosswind
PL.V.C.R2b b. Windshear
PL.V.C.R2c c. Tailwind
PL.V.C.R2d d. Low level turbulence
PL.V.C.R2e e. Surface conditions
PL.V.C.R3 Abnormal operations including:
PL.V.C.R3a a. Rejected takeoff
PL.V.C.R3b b. Powerplant failure in takeoff/climb phase of flight
PL.V.C.R4 Collision hazards.
PL.V.C.R5 Low altitude maneuvering, including controlled flight into terrain (CFIT).
PL.V.C.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.V.C.S1 Complete the appropriate checklist(s).
PL.V.C.S2 Make radio calls as appropriate.
PL.V.C.S3 Determine wind direction with or without visible wind direction indicators.
PL.V.C.S4 Position the flight controls and configure the aircraft for the existing wind conditions.
PL.V.C.S5 Clear the area, taxi into takeoff position, utilizing maximum available takeoff area and align the aircraft on the takeoff path.
PL.V.C.S6 Confirm takeoff power and proper powerplant and flight instrument indications prior to takeoff.
PL.V.C.S7 Establish and maintain the most efficient lift-off attitude/configuration for obstacle clearance.
PL.V.C.S8 Maintain the recommended airspeed and aircraft configuration until the obstacle is cleared.
PL.V.C.S9 After clearing the obstacle, establish pitch attitude and aircraft configuration for VY and accelerate to and maintain VY ±10 knots during the climb.
PL.V.C.S10 Reconfigure the aircraft after a positive rate of climb has been verified or in accordance with the aircraft manufacturer's guidance.
PL.V.C.S11 Maintain directional control and proper wind-drift correction throughout takeoff and climb.
PL.V.C.S12 Comply with noise abatement procedures.
PL.V.C.S13 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.V.C.S14 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task D. Normal Approach to a Hover
Task D. Normal Approach to a Hover
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with approach profile to a hover.
Knowledge: The applicant demonstrates understanding of:
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.D.K1 Types of approaches and applicability.
PL.V.D.K2 Performance data and the height velocity (H/V) diagram.
PL.V.D.K3 Effects of atmospheric conditions, including wind and density altitude, on approach and hover performance.
PL.V.D.K4 Wind correction techniques on approach and hover.
PL.V.D.K5 Aircraft configurations for the approach and hover.
PL.V.D.K6 Aircraft performance and limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.D.R1 Selection of runway/helipad/touchdown point based on aircraft performance and limitations, available distance, and wind.
PL.V.D.R2 Effects of:
PL.V.D.R2a a. Crosswind
PL.V.D.R2b b. Windshear
PL.V.D.R2c c. Tailwind
PL.V.D.R2d d. Wake turbulence
PL.V.D.R2e e. Vortex ring state (VRS)
PL.V.D.R2f f. Runway/arrival point surface/condition
PL.V.D.R3 Situations including:
PL.V.D.R3a a. Rejected landing and go-around
PL.V.D.R3b b. Powerplant failure during the approach
PL.V.D.R4 Collision hazards.
PL.V.D.R5 Flat light conditions.
PL.V.D.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.V.D.S1 Complete the appropriate checklist(s).
PL.V.D.S2 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.
PL.V.D.S3 Use the appropriate techniques and aircraft configurations through all stages of the approach.
PL.V.D.S4 Consider the wind conditions, landing surface, and obstructions and select a suitable hover point.
PL.V.D.S5 Maintain appropriate ground track with crosswind correction throughout the approach.
PL.V.D.S6 Fly a stabilized approach.
PL.V.D.S7 Arrive over the arrival point at a stabilized hover ±4 feet.
PL.V.D.S8 Execute a timely go-around for any condition that may result in an unsafe approach or landing.
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.D.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.V.D.S10 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task E. Normal Approach and Landing
Task E. Normal Approach and Landing
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a normal approach and landing.
Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.
Knowledge: The applicant demonstrates understanding of:
PL.V.E.K1 Effects of atmospheric conditions, including wind, on approach speed and angle.
PL.V.E.K2 Atmospheric factors affecting performance.
PL.V.E.K3 Use of proper thrust vector angle for transition to landing.
PL.V.E.K4 Factors affecting the profile of the height/velocity (H/V) diagram.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.E.R1 Selection of runway/helipad/touchdown point based on aircraft performance and limitations, available distance, and wind.
PL.V.E.R2 Effects of:
PL.V.E.R2a a. Crosswind
PL.V.E.R2b b. Windshear
PL.V.E.R2c c. Tailwind
PL.V.E.R2d d. Wake turbulence
PL.V.E.R2e e. Runway/heliport/helipad surface, condition, and length
PL.V.E.R3 Situations including:
PL.V.E.R3a a. Rejected landing and go-around
PL.V.E.R3b b. Powerplant failure during the approach
PL.V.E.R4 Collision hazards.
PL.V.E.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.V.E.S1 Complete the appropriate checklist(s).
PL.V.E.S2 Comply with noise abatement procedures.
PL.V.E.S3 Make radio calls as appropriate.
PL.V.E.S4 Verify assigned/correct runway/landing point if at an airport.
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.E.S5 Determine wind direction with or without visible wind direction indicators.
PL.V.E.S6 Maintain proper ground track with crosswind correction, if necessary.
PL.V.E.S7 Maintain a stabilized approach profile.
PL.V.E.S8 Use manufacturer's recommended technique and remain within airspeed range allowed for each configuration change.
PL.V.E.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.V.E.S10 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task F. Steep Approach and Landing
Task F. Steep Approach and Landing
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a steep approach to the surface.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
PL.V.F.K1 A stabilized steep approach.
PL.V.F.K2 Approach techniques and applicability.
PL.V.F.K3 Performance data and the height velocity (H/V) diagram.
PL.V.F.K4 Effects of atmospheric conditions on approach and landing performance.
PL.V.F.K5 Wind correction techniques.
PL.V.F.K6 Aircraft configuration.
PL.V.F.K7 Aircraft performance and limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.F.R1 Selection of the approach path and landing area.
PL.V.F.R2 Effects of:
PL.V.F.R2a a. Crosswind
PL.V.F.R2b b. Windshear
PL.V.F.R2c c. Tailwind
PL.V.F.R2d d. Wake turbulence
PL.V.F.R2e e. Vortex ring state (VRS)
PL.V.F.R2f f. Landing point condition
PL.V.F.R3 Planning for:
PL.V.F.R3a a. Rejected landing and go-around
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.F.R3b b. Powerplant failure during the approach
PL.V.F.R4 Landing in an area or in conditions where a takeoff/climb may not be possible.
PL.V.F.R5 Degraded Visual Environment (DVE) and flat light conditions.
PL.V.F.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.V.F.S1 Complete the appropriate checklist(s).
PL.V.F.S2 Position the flight controls, including the thrust vector, for the prevailing environmental conditions.
PL.V.F.S3 Maintain awareness of aircraft performance, limitations, and relative position throughout the maneuver.
PL.V.F.S4 Arrive over the touchdown point on the surface ±5 feet from intended landing point or, at the discretion of the evaluator, at a stabilized hover ±5 feet height.
PL.V.F.S5 Maintain proper ground track with crosswind correction, if necessary.
PL.V.F.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.V.F.S8 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task G. Running/Roll-On Landing
Task G. Running/Roll-On Landing
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with running/roll-on landing operation.
Knowledge: The applicant demonstrates understanding of:
PL.V.G.K1 H/V diagram, if applicable.
PL.V.G.K2 Aircraft performance and limitations.
PL.V.G.K3 Aircraft configuration.
PL.V.G.K4 Effects of atmospheric conditions, including wind, on approach and landing performance.
PL.V.G.K5 Wind correction techniques on approach and landing.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.G.R1 Situations including:
PL.V.G.R1a a. Powerplant failure during approach
PL.V.G.R1b b. Rejected landing
PL.V.G.R2 Effects of:
PL.V.G.R2a a. Crosswind
PL.V.G.R2b b. Windshear
PL.V.G.R2c c. Tailwind
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.G.R2d d. Wake turbulence
PL.V.G.R2e e. Runway surface/condition
PL.V.G.R3 Collision hazards.
PL.V.G.R4 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
PL.V.G.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.V.G.S1 Complete the appropriate checklist(s).
PL.V.G.S2 Ensure the aircraft is correctly configured for the landing.
PL.V.G.S3 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.
PL.V.G.S4 Maintain a ground track that ensures the desired traffic pattern flown takes into consideration obstructions and air traffic control (ATC) or evaluator instructions.
PL.V.G.S5 Ensure the aircraft is aligned with the correct/assigned runway or landing surface.
PL.V.G.S6 Consider the wind conditions, aircraft performance, landing surface, obstructions, and select a suitable touchdown point.
PL.V.G.S7 Maintain crosswind correction and directional control throughout the approach and landing.
PL.V.G.S8 Make smooth, timely, and correct control application during round out and touchdown.
PL.V.G.S9 Touch down at the appropriate speed, aircraft configuration and pitch attitude.
PL.V.G.S10 On touchdown, maintain proper ground track.
PL.V.G.S11 After touchdown, reconfigure the aircraft for surface/hover taxi.
PL.V.G.S12 Execute a timely go-around for any condition that may result in an unsafe approach or landing.
PL.V.G.S13 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.V.G.S14 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task H. Confined Area Operations
Task H. Confined Area Operations
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with confined area operations.
Knowledge: The applicant demonstrates understanding of:
PL.V.H.K1 Effects of wind, weight, temperature, and density altitude.
PL.V.H.K2 Situations when a confined area approach and landing is recommended and factors related to landing performance including H/V diagram information.
PL.V.H.K3 High and low reconnaissance, including takeoff and departure planning.
PL.V.H.K4 Power requirements versus power available for the departure or arrival profile(s).
Risk
Area of Operation V. Takeoffs, Landings, and Go-Arounds
Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.H.R1 Selection of approach path, termination point and departure path based on aircraft performance and limitations, wind, and availability of alternate sites.
PL.V.H.R2 Effects of:
PL.V.H.R2a a. Wind Direction
PL.V.H.R2b b. Windshear
PL.V.H.R2c c. Turbulence
PL.V.H.R3 H/V diagram information.
PL.V.H.R4 Go-around.
PL.V.H.R5 Forced landing during the maneuver.
PL.V.H.R6 Landing surface.
PL.V.H.R7 Dynamic rollover.
PL.V.H.R8 Ground resonance.
PL.V.H.R9 Collision hazards.
PL.V.H.R10 Vortex ring state (VRS).
PL.V.H.R11 Aircraft limitations.
PL.V.H.R12 Low altitude maneuvering.
PL.V.H.R13 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.V.H.R14 Power requirements versus power available for the departure or arrival profile(s).
Skills: The applicant exhibits the skill to:
PL.V.H.S1 Complete the appropriate checklist(s).
PL.V.H.S2 Make radio calls as appropriate.
PL.V.H.S3 Confirm power available meets or exceeds the power required for the selected departure or arrival profile(s).
PL.V.H.S4 Determine wind direction with or without visible wind direction indicators.
PL.V.H.S5 Accomplish a proper high and low reconnaissance of the confined landing area.
PL.V.H.S6 Select a suitable approach path, termination point, and departure path.
PL.V.H.S7 Track the selected approach path at an acceptable approach angle and rate of closure to the termination point.
PL.V.H.S8 Continually evaluate the suitability of the confined landing area and termination point.
PL.V.H.S9 Maintain powerplant and thrust output within normal limits.
PL.V.H.S10 Execute a timely go-around if the approach cannot be made within the tolerances specified above or for any other condition that may result in an unsafe approach or landing.
PL.V.H.S11 Accomplish a proper ground reconnaissance.
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.H.S12 Terminate in a hover or on the surface, as appropriate.
PL.V.H.S13 Use runway incursion avoidance procedures, if applicable.
PL.V.H.S14 Conduct a takeoff and departure using the appropriate technique and aircraft configuration.
PL.V.H.S15 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task I. Slope Operations
Task I. Slope Operations
References: 14 CFR part 91; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with slope operations.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
PL.V.I.K1 Elements related to slope operations.
PL.V.I.K2 Factors used for selecting an appropriate slope.
PL.V.I.K3 Effect of wind on slope operations.
PL.V.I.K4 Dynamic rollover considerations during slope operations and preventive/recovery techniques.
PL.V.I.K5 Aircraft configuration and slope limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.I.R1 Aircraft configuration.
PL.V.I.R2 Operations on a slope.
PL.V.I.R3 Conditions leading to dynamic rollover.
PL.V.I.R4 Flight control limits.
PL.V.I.R5 Surface conditions.
PL.V.I.R6 Embarking or disembarking passengers.
PL.V.I.R7 Exceeding the manufacturer's slope limitations.
Skills: The applicant exhibits the skill to:
PL.V.I.S1 Select a suitable slope.
PL.V.I.S2 Complete the appropriate checklist(s).
PL.V.I.S3 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.
PL.V.I.S4 Maintain heading and ground position and prevent movement of aircraft on slope.
PL.V.I.S5 Recognize if slope is too steep and abandon the operation prior to reaching flight control limits.
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.I.S6 Make a smooth positive descent to touch the upslope landing gear on the sloping surface.
PL.V.I.S7 Neutralize controls after landing.
PL.V.I.S8 Make a smooth transition from the slope to a stabilized hover parallel to the slope.
PL.V.I.S9 Properly move away from the slope.
PL.V.I.S10 Maintain positive control of aircraft throughout the maneuver.
PL.V.I.S11 Use controls while lowering the downslope landing gear to touchdown.
PL.V.I.S12 Maintain specified headings throughout the operation, ±10°.
PL.V.I.S13 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task J. Pinnacle Operations
Task J. Pinnacle Operations
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with pinnacle operations.
Knowledge: The applicant demonstrates understanding of:
PL.V.J.K1 Elements of pinnacle/platform operations.
PL.V.J.K2 Effects of wind, weight, temperature, and density altitude.
PL.V.J.K3 Suitable takeoff point and departure flight path during climb.
PL.V.J.K4 Situations when a pinnacle/platform approach, landing and takeoff is recommended and factors related to aircraft performance.
PL.V.J.K5 Elements of a high and low reconnaissance.
PL.V.J.K6 Power requirements versus power available for the departure or arrival profile(s).
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.J.R1 Selection of approach path, termination point and departure path based on aircraft performance and limitations, and wind.
PL.V.J.R2 Effects of:
PL.V.J.R2a a. Wind Direction
PL.V.J.R2b b. Windshear
PL.V.J.R2c c. Turbulence
PL.V.J.R3 H/V diagram information.
PL.V.J.R4 Go-around.
PL.V.J.R5 Powerplant failure during approach/landing phase of flight.
PL.V.J.R6 Collision hazards.
PL.V.J.R7 Vortex ring state (VRS).
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.J.R8 Landing surface.
PL.V.J.R9 Dynamic rollover.
PL.V.J.R10 Ground resonance.
PL.V.J.R11 Aircraft limitations.
PL.V.J.R12 Low altitude maneuvering.
PL.V.J.R13 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.V.J.R14 Passenger exposure to thrust or exhaust.
PL.V.J.R15 Forced landing.
PL.V.J.R16 Power requirements versus power available for the departure or arrival profile(s).
Skills: The applicant exhibits the skill to:
PL.V.J.S1 Complete the appropriate checklist(s).
PL.V.J.S2 Confirm power available meets or exceeds the power required for the selected departure or arrival profile(s).
PL.V.J.S3 Make radio calls as appropriate.
PL.V.J.S4 Accomplish high and low reconnaissance.
PL.V.J.S5 Determine wind direction with or without visible wind direction indicators.
PL.V.J.S6 Select a suitable approach path, termination point, and departure path.
PL.V.J.S7 Select an approach path considering wind direction.
PL.V.J.S8 Track the selected approach path at an acceptable approach angle and rate of closure to the termination point.
PL.V.J.S9 Maintain powerplant and thrust output within normal limits.
PL.V.J.S10 Execute a timely go-around if the approach cannot be made within the tolerances specified above or for any other condition that may result in an unsafe approach or landing.
PL.V.J.S11 Accomplish a proper ground reconnaissance.
PL.V.J.S12 Terminate in a hover or on the surface, as appropriate.
PL.V.J.S13 Select a suitable takeoff point and consider factors affecting takeoff and climb performance under various conditions.
Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task K. Go-Around/Rejected Landing
Task K. Go-Around/Rejected Landing
References: AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with go-around/rejected landing with emphasis on factors that contribute to landing conditions that may require a go-around.
Knowledge: The applicant demonstrates understanding of:
PL.V.K.K1 Situations and considerations on approach that could require a go-around/rejected landing.
Area of Operation V. Takeoffs, Landings, and Go-Arounds
PL.V.K.K2 Effects of atmospheric conditions on a go-around or rejected landing.
PL.V.K.K3 Aircraft configuration changes and techniques for the go-around.
PL.V.K.K4 Go-around/rejected landing procedures, the importance of a timely decision, and appropriate airspeeds for the maneuver.
PL.V.K.K5 Wind correction techniques.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.V.K.R1 Recognition of the need for a go-around/rejected landing.
PL.V.K.R2 Aircraft performance.
PL.V.K.R3 Application of power.
PL.V.K.R4 Aircraft configuration.
PL.V.K.R5 Collision hazards.
PL.V.K.R6 Low altitude maneuvering, including stall or controlled flight into terrain (CFIT).
PL.V.K.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.V.K.S1 Make a timely decision to go-around/reject the landing.
PL.V.K.S2 Apply the appropriate power setting for the flight condition and establish an aircraft configuration necessary to obtain the desired performance.
PL.V.K.S3 Establish a positive rate of climb and the appropriate airspeed ±10 knots.
PL.V.K.S4 Configure the aircraft, as appropriate.
PL.V.K.S5 Maintain the ground track, heading, or course appropriate for the conditions, or as specified by air traffic control (ATC) or the evaluator.
PL.V.K.S6 Notify/coordinate with air traffic control (ATC) or evaluator instructions as required.
PL.V.K.S7 Complete the appropriate checklist(s).
PL.V.K.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.V.K.S9 Use runway incursion avoidance procedures, if applicable.
Area of Operation VI. Performance Maneuvers › Task A. Rapid Deceleration/Quick Stop
Area of Operation VI. Performance Maneuvers
Area of Operation VI. Performance Maneuvers
Task A. Rapid Deceleration/Quick Stop
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with rapid deceleration/quick stop and conditions that may require a rapid deceleration/quick stop.
Knowledge: The applicant demonstrates understanding of:
PL.VI.A.K1 Purpose of the maneuver.
PL.VI.A.K2 Aircraft transmission and powerplant limitations.
PL.VI.A.K3 Airspeed limitations.
PL.VI.A.K4 Aircraft maximum rate deceleration rate and technique.
PL.VI.A.K5 Height velocity (H/V) awareness.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.VI.A.R1 Gaining or losing altitude.
PL.VI.A.R2 Excessive pitch attitudes.
PL.VI.A.R3 Effects of wind.
PL.VI.A.R4 Airframe and airspeed limitations.
PL.VI.A.R5 Collision hazards.
PL.VI.A.R6 Dividing attention between aircraft control and orientation.
PL.VI.A.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VI.A.R8 Uncoordinated flight.
PL.VI.A.R9 Vortex ring state (VRS).
Skills: The applicant exhibits the skill to:
PL.VI.A.S1 Complete the appropriate checklist(s).
PL.VI.A.S2 Clear the area.
PL.VI.A.S3 Maintain heading throughout the maneuver, ±10°.
PL.VI.A.S4 Perform a maximum performance deceleration as directed by the evaluator.
PL.VI.A.S5 Select an appropriate power setting and thrust vector to allow deceleration at maximum rate.
PL.VI.A.S6 Maintain coordinated flight throughout the maneuver.
Area of Operation VI. Performance Maneuvers › Task B. Inflight Conversion During Straight-and-Level Flight
Task B. Inflight Conversion During Straight-and-Level Flight
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with
Area of Operation VI. Performance Maneuvers
converting from thrust-borne configuration to wing-borne configuration, and returning to thrust-borne configuration.
Knowledge: The applicant demonstrates instructional knowledge by describing and explaining:
PL.VI.B.K1 Procedures for changing aircraft configuration.
PL.VI.B.K2 Aerodynamic effects of changing aircraft configuration.
PL.VI.B.K3 Flight control operation when converting from thrust-borne to wing-borne configuration, and when converting from wing-borne to thrust-borne configuration, while in straight-and-level flight.
PL.VI.B.K4 Aircraft performance and limitation charts.
PL.VI.B.K5 Factors related to weight and balance and center of gravity (CG) envelopes.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.VI.B.R1 Aircraft performance limitations.
PL.VI.B.R2 Powerplant failure during conversion.
PL.VI.B.R3 Aerodynamic stall.
PL.VI.B.R4 Effects of gross weight and CG.
PL.VI.B.R5 Rapid configuration or thrust vector changes.
PL.VI.B.R6 Altitude variation/vertical speed.
PL.VI.B.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VI.B.R8 Other hazards specific to the powered-lift make and model.
Skills: The applicant exhibits the skill to:
PL.VI.B.S1 Convert from thrust-borne configuration to wing-borne configuration during straight-and-level flight.
PL.VI.B.S2 Convert the aircraft from wing-borne configuration to thrust-borne configuration during straight-andlevel flight.
PL.VI.B.S3 Utilize proper control technique throughout the maneuver.
PL.VI.B.S4 Maintain awareness of aircraft performance, limitations, and relative position throughout the maneuver.
PL.VI.B.S5 Maintain altitude ±200 feet and specified heading ±10° throughout the operation. Achieve and maintain targeted airspeed ±10 knots.
PL.VI.B.S6 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
PL.VI.B.S7 Use the appropriate checklist, if applicable.
Area of Operation VI. Performance Maneuvers › Task C. Steep Turns
Task C. Steep Turns
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with steep turns. PL.VI.C.K1 Aerodynamics associated with steep turns, including:
Area of Operation VI. Performance Maneuvers
PL.VI.C.K1a a. Maintaining coordinated flight
PL.VI.C.K1b b. Overbanking tendencies
PL.VI.C.K1c c. Maneuvering speed, including the impact of weight changes
PL.VI.C.K1d d. Load factor and accelerated stalls
PL.VI.C.K1e e. Rate and radius of turn
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.VI.C.R1 Dividing attention between aircraft control and orientation.
PL.VI.C.R2 Collision hazards.
PL.VI.C.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
PL.VI.C.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VI.C.R5 Uncoordinated flight.
Skills: The applicant exhibits the skill to:
PL.VI.C.S1 Clear the area.
PL.VI.C.S2 Establish the manufacturer's recommended airspeed; or if one is not available, an airspeed not to exceed maneuvering speed (VA).
PL.VI.C.S3 Roll into a coordinated 360° steep turn as selected by the evaluator and according to the aircraft's operating limitations.
PL.VI.C.S4 Perform the maneuver in the opposite direction.
PL.VI.C.S5 Maintain the entry altitude ±100 feet, airspeed ±10 knots, bank ±5°, and roll out on the entry heading ±10°.
Area of Operation VII. Ground Reference Maneuvers › Task A. Ground Reference Maneuvers
Area of Operation VII. Ground Reference Maneuvers
Area of Operation VII. Ground Reference Maneuvers
Task A. Ground Reference Maneuvers
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with ground reference maneuvering which may include a rectangular course, S-turns, and turns around a point.
Note: The evaluator selects at least one ground reference maneuver for the applicant to demonstrate.
Knowledge: The applicant demonstrates understanding of:
PL.VII.A.K1 Purpose of ground reference maneuvers.
PL.VII.A.K2 Effects of wind on ground track and relation to a ground reference.
PL.VII.A.K3 Effects of bank angle and groundspeed on rate and radius of turn.
PL.VII.A.K4 Relationship of rectangular course to airport traffic pattern.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.VII.A.R1 Division of attention between aircraft control and orientation.
PL.VII.A.R2 Collision hazards.
PL.VII.A.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
PL.VII.A.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VII.A.R5 Uncoordinated flight.
Skills: The applicant exhibits the skill to:
PL.VII.A.S1 Clear the area.
PL.VII.A.S2 Select a suitable ground reference area, line, or point as appropriate.
PL.VII.A.S3 Plan the maneuver:
PL.VII.A.S3a a. Rectangular course: enter a left or right pattern, 600 to 1,000 feet above ground level (AGL) at
an appropriate distance from the selected reference area, 45° to the downwind leg
PL.VII.A.S3b b. S-turns: enter perpendicular to the selected reference line, 600 to 1,000 feet AGL at an
appropriate distance from the selected reference area
PL.VII.A.S3c c. Turns around a point: enter at an appropriate distance from the reference point, 600 to 1,000
feet AGL at an appropriate distance from the selected reference area
PL.VII.A.S4 Apply adequate wind-drift correction during straight and turning flight to maintain a constant ground track around a rectangular reference area, or to maintain a constant radius turn on each side of a selected reference line or point.
PL.VII.A.S5 If performing S-Turns, reverse the turn directly over the selected reference line; if performing turns around a point, complete turns in either direction, as specified by the evaluator.
PL.VII.A.S6 Divide attention between aircraft control, traffic avoidance and the ground track while maintaining coordinated flight.
PL.VII.A.S7 Maintain altitude ±100 feet; maintain airspeed ±10 knots.
Area of Operation VIII. Navigation › Task A. Pilotage and Dead Reckoning
Area of Operation VIII. Navigation
Area of Operation VIII. Navigation
Task A. Pilotage and Dead Reckoning
References: AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with airworthiness requirements, including aircraft certificates.
Knowledge: The applicant demonstrates understanding of:
PL.VIII.A.K1 Pilotage and dead reckoning.
PL.VIII.A.K2 Magnetic compass errors.
PL.VIII.A.K3 Topography.
PL.VIII.A.K4 Selection of appropriate:
PL.VIII.A.K4a a. Route
PL.VIII.A.K4b b. Altitude(s)
PL.VIII.A.K4c c. Checkpoints
PL.VIII.A.K5 Plotting a course, including:
PL.VIII.A.K5a a. Determining heading, speed, and course
PL.VIII.A.K5b b. Wind correction angle
PL.VIII.A.K5c c. Estimating time, speed, and distance
PL.VIII.A.K5d d. True airspeed and density altitude
PL.VIII.A.K6 Aircraft configuration.
PL.VIII.A.K7 Planned calculations versus actual results and required corrections.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.VIII.A.R1 Collision hazards.
PL.VIII.A.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VIII.A.R3 Unplanned fuel/power consumption, if applicable.
Skills: The applicant exhibits the skill to:
PL.VIII.A.S1 Prepare and use a flight log.
PL.VIII.A.S2 Navigate by pilotage.
PL.VIII.A.S3 Navigate by means of pre-computed headings, groundspeeds, elapsed time, and reference to landmarks or checkpoints.
PL.VIII.A.S4 Use the magnetic direction indicator in navigation, including turns to headings.
PL.VIII.A.S5 Correct for and record the differences between preflight fuel, groundspeed, and heading calculations and those determined en route.
Area of Operation VIII. Navigation
PL.VIII.A.S6 Verify position within three nautical miles of the flight-planned route.
PL.VIII.A.S7 Arrive at the en route checkpoints within five minutes of the initial or revised estimated time of arrival (ETA) and provide a destination estimate.
PL.VIII.A.S8 Maintain the selected altitude, ±200 feet and heading, ±15°.
Area of Operation VIII. Navigation › Task B. Navigation Systems and Radar Services
Task B. Navigation Systems and Radar Services
References: AC 91-78; AIM; FAA-H-8083-2, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with navigation systems and radar services.
Note: The evaluator should reference the manufacturer’s equipment supplement(s) as necessary for appropriate limitations, procedures, etc.
Knowledge: The applicant demonstrates understanding of:
PL.VIII.B.K1 Ground-based navigation (identification, orientation, course determination, equipment, tests, regulations, interference, appropriate use of navigation data, and signal integrity).
PL.VIII.B.K2 Satellite-based navigation (e.g., equipment, regulations, authorized use of databases, and Receiver Autonomous Integrity Monitoring (RAIM)).
PL.VIII.B.K3 Radar assistance to visual flight rules (VFR) aircraft (e.g., operations, equipment, available services, traffic advisories).
PL.VIII.B.K4 Transponder (Mode(s) A, C, and S) and Automatic Dependent Surveillance-Broadcast (ADS-B).
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.VIII.B.R1 Management of automated navigation and autoflight systems.
PL.VIII.B.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VIII.B.R3 Limitations of the navigation system in use.
PL.VIII.B.R4 Loss of a navigation signal.
PL.VIII.B.R5 Use of an electronic flight bag (EFB), if used.
Skills: The applicant exhibits the skill to:
PL.VIII.B.S1 Use an airborne electronic navigation system.
PL.VIII.B.S2 Determine the aircraft's position using the navigation system.
PL.VIII.B.S3 Intercept and track a given course, radial, or bearing.
PL.VIII.B.S4 Recognize and describe the indication of station or waypoint passage.
PL.VIII.B.S5 Recognize signal loss or interference and take appropriate action, if applicable.
PL.VIII.B.S6 Use proper communication procedures when utilizing radar services.
PL.VIII.B.S7 Maintain the selected altitude, ±200 feet and heading, ±15°.
Area of Operation VIII. Navigation
Area of Operation VIII. Navigation › Task C. Diversion
Task C. Diversion
References: AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with diversion.
Knowledge: The applicant demonstrates understanding of:
PL.VIII.C.K1 Selecting an alternate destination.
PL.VIII.C.K2 Situations that require deviations from flight plan or air traffic control (ATC) instructions.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.VIII.C.R1 Collision hazards.
PL.VIII.C.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VIII.C.R3 Circumstances that would make diversion prudent.
PL.VIII.C.R4 Selecting an airport/heliport/helipad, as applicable.
PL.VIII.C.R5 Using available resources (e.g., automation, ATC, and flight deck planning aids).
Skills: The applicant exhibits the skill to:
PL.VIII.C.S1 Select a suitable airport/heliport/helipad, as applicable, and route for diversion.
PL.VIII.C.S2 Make a reasonable estimate of heading, groundspeed, arrival time, and fuel required to the “divert to” destination.
PL.VIII.C.S3 Promptly divert toward the airport/heliport/helipad.
PL.VIII.C.S4 Maintain the selected altitude, ±200 feet and heading, ±15°.
PL.VIII.C.S5 Update/interpret weather in flight.
PL.VIII.C.S6 Use displays of digital weather and aeronautical information, as applicable to maintain situational awareness.
Area of Operation VIII. Navigation › Task D. Lost Procedures
Task D. Lost Procedures
References: AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with lost procedures and can take appropriate steps to achieve a satisfactory outcome if lost.
Knowledge: The applicant demonstrates understanding of:
PL.VIII.D.K1 Methods to determine position.
PL.VIII.D.K2 Assistance available if lost (e.g., radar services, communication procedures).
PL.VIII.D.K3 Rapidly deteriorating weather or impending fuel exhaustion.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
Area of Operation VIII. Navigation
PL.VIII.D.R1 Collision hazards.
PL.VIII.D.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.VIII.D.R3 Recording times over waypoints.
PL.VIII.D.R4 When to seek assistance or declare an emergency in a deteriorating situation.
Skills: The applicant exhibits the skill to:
PL.VIII.D.S1 Select an appropriate course of action.
PL.VIII.D.S2 Use an appropriate method to determine position.
PL.VIII.D.S3 Maintain an appropriate heading and climb as necessary.
PL.VIII.D.S4 Identify prominent landmarks.
PL.VIII.D.S5 Use navigation systems/facilities or contact an ATC facility for assistance.
Area of Operation IX. Slow Flight and Stalls › Task A. Maneuvering During Slow Flight (Wing-Borne Configuration)
Area of Operation IX. Slow Flight and Stalls
Area of Operation IX. Slow Flight and Stalls
Task A. Maneuvering During Slow Flight (Wing-Borne Configuration)
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with maneuvering during slow flight in wing-borne configuration.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
PL.IX.A.K1 Aerodynamics associated with slow flight in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.IX.A.R1 Inadvertent slow flight and flight with a stall warning, which could lead to loss of control.
PL.IX.A.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
PL.IX.A.R3 Uncoordinated flight.
PL.IX.A.R4 Effect of environmental elements on aircraft performance (e.g., turbulence, microbursts, and high density altitude).
PL.IX.A.R5 Collision hazards.
PL.IX.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.IX.A.S1 Clear the area.
PL.IX.A.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet above ground level (AGL).
PL.IX.A.S3 Establish and maintain an airspeed at which any further increase in angle of attack, increase in load factor, or reduction in power, would result in a stall warning (e.g., aircraft buffet, stall horn, etc.).
PL.IX.A.S4 Accomplish coordinated straight-and-level flight, turns, climbs, and descents with the aircraft configured as specified by the evaluator without a stall warning (e.g., aircraft buffet, stall horn, etc.).
PL.IX.A.S5 Maintain the specified altitude, ±100 feet; specified heading, ±10°; airspeed, +10/-0 knots; and specified angle of bank, ±10°.
Area of Operation IX. Slow Flight and Stalls › Task B. Power-Off Stalls
Task B. Power-Off Stalls
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-off stalls.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Area of Operation IX. Slow Flight and Stalls
Knowledge: The applicant demonstrates understanding of:
PL.IX.B.K1 Aerodynamics associated with stalls in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.
PL.IX.B.K2 Stall characteristics as they relate to aircraft design, and recognition impending stall and full stall indications using sight, sound, or feel.
PL.IX.B.K3 Factors and situations that can lead to a power-off stall and actions that can be taken to prevent it.
PL.IX.B.K4 Fundamentals of stall recovery.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.IX.B.R1 Factors and situations that could lead to an inadvertent power-off stall, spin, and loss of control.
PL.IX.B.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
PL.IX.B.R3 Stall warning(s) during normal operations.
PL.IX.B.R4 Stall recovery procedure.
PL.IX.B.R5 Secondary and accelerated stalls.
PL.IX.B.R6 Effect of environmental elements on aircraft performance related to power-off stalls (e.g., turbulence, microbursts, and high-density altitude).
PL.IX.B.R7 Collision hazards.
PL.IX.B.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.IX.B.S1 Clear the area.
PL.IX.B.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet AGL or as recommended by the manufacturer, whichever is higher.
PL.IX.B.S3 Configure the aircraft in the approach or landing configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver.
PL.IX.B.S4 Establish a stabilized descent.
PL.IX.B.S5 Transition smoothly from the approach or landing attitude to a pitch attitude that induces a stall.
PL.IX.B.S6 Maintain a specified heading, ±10° if in straight flight; maintain a specified angle of bank not to exceed 20°, ±10° if in turning flight, while inducing the stall.
PL.IX.B.S7 Acknowledge cues of the impending stall and then recover promptly after a full stall occurs.
PL.IX.B.S8 Execute a stall recovery in accordance with procedures set forth in the Flight Manual.
PL.IX.B.S9 Configure the aircraft as recommended by the manufacturer and accelerate to VX or VY.
PL.IX.B.S10 Return to the altitude, heading, and airspeed specified by the evaluator.
PL.IX.B.S11 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation IX. Slow Flight and Stalls
Area of Operation IX. Slow Flight and Stalls › Task C. Power-On Stalls
Task C. Power-On Stalls
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-on stalls.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
PL.IX.C.K1 Aerodynamics associated with stalls in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.
PL.IX.C.K2 Stall characteristics as they relate to aircraft design, and recognition impending stall and full stall indications using sight, sound, or feel.
PL.IX.C.K3 Factors and situations that can lead to a power-on stall and actions that can be taken to prevent it.
PL.IX.C.K4 Fundamentals of stall recovery.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.IX.C.R1 Factors and situations that could lead to an inadvertent power-on stall, spin, and loss of control.
PL.IX.C.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
PL.IX.C.R3 Pitch attitude limitations.
PL.IX.C.R4 Stall warning(s) during normal operations.
PL.IX.C.R5 Stall recovery procedure.
PL.IX.C.R6 Secondary stalls and accelerated stalls.
PL.IX.C.R7 Effect of environmental elements on aircraft performance related to power-on stalls (e.g., turbulence, microbursts, and high-density altitude).
PL.IX.C.R8 Collision hazards.
PL.IX.C.R9 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.IX.C.S1 Clear the area.
PL.IX.C.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet AGL or as recommended by the manufacturer, whichever is higher.
PL.IX.C.S3 Establish the takeoff, departure, or wing-borne configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver.
PL.IX.C.S4 Transition smoothly from the takeoff or departure attitude to the pitch attitude that would induce a stall.
PL.IX.C.S5 Maintain a specified heading, ±10° if in straight flight; maintain a specified angle of bank not to exceed 20°, ±10° if in turning flight, while inducing the stall.
PL.IX.C.S6 Acknowledge cues of the impending stall and then recover promptly after a full stall occurs.
Area of Operation IX. Slow Flight and Stalls
PL.IX.C.S7 Execute a stall recovery in accordance with procedures set forth in the Flight Manual.
PL.IX.C.S8 Configure the aircraft as recommended by the manufacturer and accelerate to VX or VY.
PL.IX.C.S9 Return to the altitude, heading, and airspeed specified by the evaluator.
PL.IX.C.S10 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation X. Basic Instrument Maneuvers › Task A. Straight-and-Level Flight
Area of Operation X. Basic Instrument Maneuvers
Area of Operation X. Basic Instrument Maneuvers
Task A. Straight-and-Level Flight
References: FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flying during straight-and-level flight solely by reference to instruments.
Knowledge: The applicant demonstrates understanding of:
PL.X.A.K1 Flight instruments as they relate to:
PL.X.A.K1a a. Instrument limitations and potential errors
PL.X.A.K1b b. Indication of the aircraft attitude
PL.X.A.K1c c. Function and operation
PL.X.A.K1d d. Instrument cross-check techniques
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.X.A.R1 Instrument flying hazards, including failure to maintain visual flight rules (VFR), spatial disorientation, loss of control, fatigue, stress, and emergency off airport landings.
PL.X.A.R2 When to seek assistance or declare an emergency in a deteriorating situation.
PL.X.A.R3 Collision hazards.
PL.X.A.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.X.A.R5 Fixation and omission.
PL.X.A.R6 Instrument Interpretation.
PL.X.A.R7 Control application solely by reference to instruments.
PL.X.A.R8 Trimming the aircraft.
Skills: The applicant exhibits the skill to:
PL.X.A.S1 Maintain straight-and-level flight using proper instrument cross-check and interpretation, and coordinated control application.
PL.X.A.S2 Maintain altitude ±200 feet, heading ±20°, and airspeed ±10 knots.
Area of Operation X. Basic Instrument Maneuvers › Task B. Constant Airspeed Climbs
Task B. Constant Airspeed Climbs
References: FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with attitude instrument flying during constant airspeed climbs solely by reference to instruments.
Knowledge: The applicant demonstrates understanding of:
PL.X.B.K1 Flight instruments as they relate to:
PL.X.B.K2a a. Instrument limitations and potential errors
Area of Operation X. Basic Instrument Maneuvers
PL.X.B.K2b b. Indication of the aircraft attitude
PL.X.B.K2c c. Function and operation
PL.X.B.K2d d. Proper instrument cross-check techniques
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.X.B.R1 Instrument flying hazards, including failure to maintain visual flight rules (VFR), spatial disorientation, loss of control, fatigue, stress, and emergency off airport landings.
PL.X.B.R2 When to seek assistance or declare an emergency in a deteriorating situation.
PL.X.B.R3 Collision hazards.
PL.X.B.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.X.B.R5 Fixation and omission.
PL.X.B.R6 Instrument Interpretation.
PL.X.B.R7 Control application solely by reference to instruments.
PL.X.B.R8 Trimming the aircraft.
Skills: The applicant exhibits the skill to:
PL.X.B.S1 Transition to the climb pitch attitude and power setting on an assigned heading using proper instrument cross-check and interpretation, and coordinated flight control application.
PL.X.B.S2 Climb at a constant airspeed to specific altitudes in straight flight and turns.
PL.X.B.S3 Level off at the assigned altitude and maintain altitude ±200 feet, heading ±20°, and airspeed ±10 knots.
Area of Operation X. Basic Instrument Maneuvers › Task C. Constant Airspeed Descents
Task C. Constant Airspeed Descents
References: FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with attitude instrument flying during constant airspeed descents solely by reference to instruments.
Knowledge: The applicant demonstrates understanding of:
PL.X.C.K1 Flight instruments as they relate to:
PL.X.C.K1a a. Instrument limitations and potential errors
PL.X.C.K1b b. Indication of the aircraft attitude
PL.X.C.K1c c. Function and operation
PL.X.C.K1d d. Proper instrument cross-check techniques
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.X.C.R1 Instrument flying hazards, including failure to maintain visual flight rules (VFR), spatial disorientation, loss of control, fatigue, stress, and emergency off airport landings.
Area of Operation X. Basic Instrument Maneuvers
PL.X.C.R2 When to seek assistance or declare an emergency in a deteriorating situation.
PL.X.C.R3 Collision hazards.
PL.X.C.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.X.C.R5 Fixation and omission.
PL.X.C.R6 Instrument Interpretation.
PL.X.C.R7 Control application solely by reference to instruments.
PL.X.C.R8 Trimming the aircraft.
Skills: The applicant exhibits the skill to:
PL.X.C.S1 Transition to the descent pitch attitude and power setting on an assigned heading using proper instrument cross-check and interpretation, and coordinated flight control application.
PL.X.C.S2 Descend at a constant airspeed to specific altitudes in straight flight and turns.
PL.X.C.S3 Level off at the assigned altitude and maintain altitude ±200 feet, heading ±20°, and airspeed ±10 knots.
Area of Operation X. Basic Instrument Maneuvers › Task D. Turns to Headings
Task D. Turns to Headings
References: FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with attitude instrument flying during turns to headings solely by reference to instruments.
Knowledge: The applicant demonstrates understanding of:
PL.X.D.K1 Flight instruments as they relate to:
PL.X.D.K1a a. Instrument limitations and potential errors
PL.X.D.K1b b. Indication of the aircraft attitude
PL.X.D.K1c c. Function and operation
PL.X.D.K1d d. Proper instrument cross-check techniques
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.X.D.R1 Instrument flying hazards, including failure to maintain visual flight rules (VFR), spatial disorientation, loss of control, fatigue, stress, and emergency off airport landings.
PL.X.D.R2 When to seek assistance or declare an emergency in a deteriorating situation.
PL.X.D.R3 Collision hazards.
PL.X.D.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.X.D.R5 Fixation and omission.
PL.X.D.R6 Instrument Interpretation.
PL.X.D.R7 Control application solely by reference to instruments.
Area of Operation X. Basic Instrument Maneuvers
PL.X.D.R8 Trimming the aircraft.
Skills: The applicant exhibits the skill to:
PL.X.D.S1 Turn to headings, maintain altitude ±200 feet, maintain a standard rate turn, roll out on the assigned heading ±10°, and maintain airspeed ±10 knots.
Area of Operation X. Basic Instrument Maneuvers › Task E. Recovery from Unusual Flight Attitudes
Task E. Recovery from Unusual Flight Attitudes
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with attitude instrument flying while recovering from unusual attitudes solely by reference to instruments.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
PL.X.E.K1 Prevention of unusual attitudes, including flight causal, physiological, and environmental factors, and system and equipment failures.
PL.X.E.K2 Procedures for recovery from unusual attitudes in flight.
PL.X.E.K3 Procedures available to safely regain visual meteorological conditions (VMC) after flight into inadvertent instrument meteorological conditions or unintended instrument meteorological conditions (IIMC)/(UIMC).
PL.X.E.K4 Appropriate use of automation, if applicable.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.X.E.R1 Situations that could lead to loss of control in-flight (LOC-I) or unusual attitudes in-flight (e.g., stress, task saturation, inadequate instrument scan distractions, and spatial disorientation).
PL.X.E.R2 Assessment of the unusual attitude.
PL.X.E.R3 Control input errors, inducing undesired aircraft attitudes.
PL.X.E.R4 Collision hazards.
PL.X.E.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.X.E.R6 Interpreting flight instruments.
PL.X.E.R7 Control application solely by reference to instruments.
PL.X.E.R8 Operating envelope considerations.
Skills: The applicant exhibits the skill to:
PL.X.E.S1 Use proper instrument cross-check and interpretation to identify an unusual attitude (including both nose-high and nose-low) in flight, and apply the appropriate flight control, power input, and aircraft configuration in the correct sequence, to return to a stabilized level flight attitude.
PL.X.E.S2 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation X. Basic Instrument Maneuvers
Area of Operation X. Basic Instrument Maneuvers › Task F.
Task F. Radio Communications, Navigation Systems/Facilities, and Radar Services
References: FAA-H-8083-2, FAA-H-8083-15, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with radio communications, navigation systems/facilities, and radar services available for use during flight solely by reference to instruments.
Knowledge: The applicant demonstrates understanding of:
PL.X.F.K1 Operating communications equipment, including identifying and selecting radio frequencies, requesting and following air traffic control (ATC) instructions.
PL.X.F.K2 Operating navigation equipment, including functions and displays, and following bearings, radials, or courses.
PL.X.F.K3 Air traffic control facilities and services.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.X.F.R1 When to seek assistance or declare an emergency in a deteriorating situation.
PL.X.F.R2 Using available resources (e.g., automation, ATC, and flight deck planning aids).
Skills: The applicant exhibits the skill to:
PL.X.F.S1 Maintain aircraft control while selecting proper communications frequencies, identifying the appropriate facility, and managing navigation equipment.
PL.X.F.S2 Comply with ATC instructions.
Area of Operation XI. Emergency Operations › Task A.
Area of Operation XI. Emergency Operations
Area of Operation XI. Emergency Operations
Task A. Powerplant(s) Failure (Simulated) during Takeoff in Thrust-Borne Flight
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with indications and pilot actions after powerplant(s) failure during takeoff while the aircraft is predominantly in thrust-borne flight in a multi-powerplant aircraft.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Note: The task outcome can be vertical or rolling depending on aircraft capabilities, configuration, and flight manual procedures.
Knowledge: The applicant demonstrates understanding of:
PL.XI.A.K1 Aircraft performance and limitations, (e.g., height velocity (H/V) diagram information).
PL.XI.A.K2 Factors involved in determining a valid go/no-go decision.
PL.XI.A.K3 Recognition of powerplant(s) failure.
PL.XI.A.K4 Pilot actions required on recognition of powerplant(s) failure, including checklist memory items.
PL.XI.A.K5 Aircraft configuration for landing with powerplant(s) failure.
PL.XI.A.K6 Causes of asymmetric thrust conditions and appropriate responses.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.XI.A.R1 Powerplant(s) failure.
PL.XI.A.R2 Identification of powerplant(s) failure conditions.
PL.XI.A.R3 Pilot reaction to powerplant(s) failure conditions.
PL.XI.A.R4 Aircraft configuration.
Skills: The applicant exhibits the skill to:
PL.XI.A.S1 Recognize that a powerplant(s) failure has occurred.
PL.XI.A.S2 Use flight controls in the proper combination and aircraft configuration as recommended by the manufacturer, or as required to maintain best performance, and trim as required.
PL.XI.A.S3 Maintain the operating powerplant(s) within acceptable operating limits.
PL.XI.A.S4 Land the aircraft, as appropriate to the scenario presented by the evaluator.
PL.XI.A.S5 Complete the appropriate checklist(s).
PL.XI.A.S6 Make radio calls as appropriate.
PL.XI.A.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation XI. Emergency Operations
Area of Operation XI. Emergency Operations › Task B.
Task B. Powerplant(s) Failure (Simulated) during Takeoff While in Semi-Wing-Borne Flight
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with indications and pilot actions after powerplant(s) failure during takeoff while in semi-wing-borne flight in a multi-powerplant aircraft.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Note: This can be initiated during the takeoff roll in wheeled aircraft or during the conversion to wing-borne flight following a vertical takeoff.
Knowledge: The applicant demonstrates understanding of:
PL.XI.B.K1 The procedures used during a powerplant(s) failure on takeoff, the appropriate reference airspeeds, and the specific pilot actions required.
PL.XI.B.K2 Operational considerations to include: aircraft performance (e.g., sideslip, bank angle, etc.), takeoff warning systems, runway length, surface conditions, density altitude, wake turbulence, environmental conditions, obstructions, and other related factors that could adversely affect safety.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.XI.B.R1 Powerplant(s) failure.
PL.XI.B.R2 Reaction to the loss of power from one or more powerplants.
PL.XI.B.R3 Deceleration in a space-limited environment.
PL.XI.B.R4 Windshear.
PL.XI.B.R5 Dividing attention inside and outside the aircraft.
PL.XI.B.R6 Runway incursion.
PL.XI.B.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.
PL.XI.B.R8 Abnormal operations, including planning for:
PL.XI.B.R8a a. Rejected takeoff
PL.XI.B.R8b b. Powerplant failure in takeoff/climb phase of flight
PL.XI.B.R9 Energy management.
Skills: The applicant exhibits the skill to:
PL.XI.B.S1 Recognize that a powerplant failure has occurred while performing a rolling takeoff.
PL.XI.B.S2 Input the appropriate flight control(s) and configure the aircraft for maximum deceleration.
PL.XI.B.S3 Maintain the operating powerplant(s) within acceptable operating limits.
PL.XI.B.S4 Apply braking as appropriate.
PL.XI.B.S5 Refer to the checklist to ensure that the emergency procedure was followed correctly.
PL.XI.B.S6 Make radio calls as appropriate.
Area of Operation XI. Emergency Operations
PL.XI.B.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation XI. Emergency Operations › Task C.
Task C. Inflight Powerplant(s) Failure and Restart in Multi-Powerplant Aircraft
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with an inflight powerplant(s) failure and restart, if applicable, in a multi-powerplant powered-lift aircraft.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
PL.XI.C.K1 Flight characteristics and controllability associated with maneuvering the aircraft with powerplant(s) inoperative, including the importance of drag reduction and appropriate aircraft configuration.
PL.XI.C.K2 Aircraft/powerplant limitations.
PL.XI.C.K3 Powerplant restart procedures and conditions where a restart attempt is appropriate.
PL.XI.C.K4 Causes of asymmetric thrust conditions and appropriate responses.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.XI.C.R1 Potential powerplant(s) failure during flight.
PL.XI.C.R2 Following checklist procedures for a powerplant(s) failure or a powerplant(s) restart.
PL.XI.C.R3 Identifying the powerplant(s) that failed.
PL.XI.C.R4 Collision hazards.
PL.XI.C.R5 Aircraft configuration.
PL.XI.C.R6 Factors and situations that could lead to loss of control with an inflight powerplant(s) failure.
PL.XI.C.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.XI.C.S1 Recognize and correctly identify powerplant(s) failure, complete memory items (if applicable), and maintain positive aircraft control.
PL.XI.C.S2 Coordinate with crew, if applicable, and complete the appropriate emergency procedures and checklist(s) for powerplant shutdown.
PL.XI.C.S3 Use flight controls and configure the aircraft in the proper combination as recommended by the manufacturer, or as required, to maintain best performance, and trim as required.
PL.XI.C.S4 Determine the cause for the powerplant(s) failure and if a restart is a viable option.
PL.XI.C.S5 Maintain the operating powerplant(s) within acceptable operating limits.
PL.XI.C.S6 Maintain the airspeed ±10 knots, the specified heading ±10°, and altitude ±100 feet as specified by the evaluator and within the aircraft’s capability.
PL.XI.C.S7 Consider a powerplant restart and, if appropriate, demonstrate the powerplant restart procedures in accordance with the manufacturer or operator specified procedures and checklists.
Area of Operation XI. Emergency Operations
PL.XI.C.S8 Select the nearest suitable airport or landing area.
PL.XI.C.S9 Communicate with air traffic control (ATC) and the evaluator, as appropriate for the situation.
PL.XI.C.S10 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation XI. Emergency Operations › Task D. Vortex Ring State (VRS) Avoidance
Task D. Vortex Ring State (VRS) Avoidance
References: FAA-H-8083-2, FAA-H-8083-25; Flight Manual
Objective: To determine the applicant exhibits satisfactory knowledge and risk management associated with preventing the aircraft from entering and the procedure for recovering from Vortex Ring State (VRS).
Note: Evaluator assesses this Task orally only.
Knowledge: The applicant demonstrates understanding of:
PL.XI.D.K1 Elements of vortex ring state.
PL.XI.D.K2 Effects of wind, weight, temperature, and density altitude.
PL.XI.D.K3 Requirements for the formation of VRS.
PL.XI.D.K4 Aircraft systems that aid the pilot in avoiding VRS, if applicable.
PL.XI.D.K5 Aerodynamics and indications of VRS.
PL.XI.D.K6 Flight scenarios under which VRS can occur.
PL.XI.D.K7 Asymmetric VRS, if applicable.
PL.XI.D.K8 Effective recovery techniques.
PL.XI.D.K9 Control inputs and configuration changes to recover from VRS.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
PL.XI.D.R1 Conditions for entering VRS.
PL.XI.D.R2 Pilot recognition and response to VRS.
PL.XI.D.R3 Loss of control.
PL.XI.D.R4 Collision hazards.
PL.XI.D.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
PL.XI.D.S1 [Intentionally left blank].
Continue reading ↓ 120 of 175 passages shown