Radar Vectors
Certification Standard Current Issued May 31, 2024 Flight Standards Service 75 pages Copy saved Nov 18, 2026

FAA-S-ACS-2 Commercial Pilot for Powered-Lift Category Airman Certification Standards

Official source ↗ Open PDF

Commercial Pilot for Powered-Lift Category

Airman Certification Standards

FAA-S-ACS-2

Flight Standards Service

Washington, DC 20591

November 2023

Commercial Pilot for Powered-Lift Category ACS (FAA-S-ACS-2) i

Foreword

The U.S. Department of Transportation, Federal Aviation Administration (FAA), Office of Safety Standards, Regulatory Support Division, Airman Testing Standards Branch, has published the Commercial Pilot for Powered-Lift Category Airman Certification Standards (ACS) to communicate the aeronautical knowledge, risk management, and flight proficiency standards for commercial pilot certification in the powered-lift category.

This ACS is available for download, in PDF format, from www.faa.gov.

Comments regarding this ACS may be emailed to [email protected].

The FAA created FAA-G-ACS-2, Airman Certification Standards Companion Guide for Pilots, to provide guidance considered relevant and useful to the community. The number of appendices in the ACS was reduced and much of the non-regulatory material was moved to the Airman Certification Standards Companion Guide for Pilots. Applicants, instructors, and evaluators should consult this companion guide to familiarize themselves with ACS procedures. FAA-G-ACS-2 is available for download, in PDF format, from www.faa.gov.

Commercial Pilot for Powered-Lift Category ACS (FAA-S-ACS-2) ii

Table of Contents Introduction

Airman Certification Standards Concept … 1 Use of the Term “Flight Manual” … 1

Area of Operation I. Preflight Preparation

Task A. Pilot Qualifications … 2 Task B. Airworthiness Requirements … 2 Task C. Weather Information … 3 Task D. Cross-Country Flight Planning … 4 Task E. National Airspace System … 5 Task F. Performance and Limitations … 6 Task G. Operation of Systems … 7 Task H. Human Factors … 8 Task I. Night Operations … 9

Area of Operation II. Preflight Procedures

Task A. Preflight Assessment … 10 Task B. Flight Deck Management … 10 Task C. Powerplant Starting … 11 Task D. Ground Taxiing … 12 Task E. Before Takeoff Check … 13

Area of Operation III. Airport and Heliport Operations

Task A. Communications, Light Signals, and Runway Lighting Systems … 15 Task B. Runway/Taxiway/Heliport/Helipad Signs, Markings, and Lighting … 15 Task C. Traffic Patterns … 16

Area of Operation IV. Hovering Maneuvers

Task A. Vertical Takeoff and Landing … 18 Task B. Hover Taxi … 18 Task C. Air Taxi … 20

Area of Operation V. Takeoffs, Landings, and Go-Arounds

Task A. Normal Takeoff and Climb from a Hover … 22 Task B. Rolling Takeoff and Climb … 23 Task C. Maximum Performance Takeoff and Climb … 24 Task D. Normal Approach to a Hover … 25 Task E. Normal Approach and Landing … 27 Task F. Steep Approach and Landing … 28 Task G. Running/Roll-On Landing … 29

Commercial Pilot for Powered-Lift Category ACS (FAA-S-ACS-2) iii

Table of Contents

Task H. Go-Around/Rejected Landing … 30

Area of Operation VI. Performance Maneuvers

Task A. Rapid Deceleration/Quick Stop … 32 Task B. Inflight Conversion During Straight-and-Level Flight … 32 Task C. Steep Turns … 33

Area of Operation VII. Navigation

Task A. Pilotage and Dead Reckoning … 35 Task B. Navigation Systems and Radar Services … 36 Task C. Diversion … 37 Task D. Lost Procedures … 37

Area of Operation VIII. Slow Flight and Stalls

Task A. Maneuvering During Slow Flight (Wing-Borne Configuration) … 39 Task B. Power-Off Stalls … 39 Task C. Power-On Stalls … 41 Task D. Accelerated Stalls … 42

Area of Operation IX. Emergency Operations

Task A. Powerplant(s) Failure (Simulated) during Takeoff in Thrust-Borne Flight … 44 Task B. Powerplant(s) Failure (Simulated) during Takeoff While in Semi-Wing-Borne Flight … 45 Task C. Inflight Powerplant(s) Failure and Restart in Multi-Powerplant Aircraft … 46 Task D. Vortex Ring State (VRS) Avoidance … 47 Task E. Approach and Landing with Powerplant(s) Failure (Simulated) … 47 Task F. Emergency Descent … 48 Task G. Emergency Equipment and Survival Gear … 49 Task H. Systems and Equipment Malfunctions … 50 Task I. Dynamic Rollover … 51 Task J. Recovery from Unusual Flight Attitudes … 51

Area of Operation X. High-Altitude Operations

Task A. Supplemental Oxygen … 53 Task B. Pressurization … 53

Area of Operation XI. Special Operations

Task A. Confined Area Operations … 55 Task B. Slope Operations … 56 Task C. Pinnacle Operations … 57

Commercial Pilot for Powered-Lift Category ACS (FAA-S-ACS-2) iv

Table of Contents

Area of Operation XII. Postflight Procedures

Task A. After Landing, Parking, and Securing … 60

Appendix 1: Practical Test Roles, Responsibilities, and Outcomes

Eligibility Requirements for a Commercial Pilot Certificate … 61 Use of the ACS During a Practical Test … 61 Instructor Responsibilities … 62 Evaluator Responsibilities … 62 Possible Outcomes of the Test … 63 Additional Rating Task Table … 64 Addition of a Powered-Lift Rating to an Existing Commercial Pilot Certificate … 65

Appendix 2: Safety of Flight

General … 66 Stall, Spin, Angle of Attack Awareness … 66 Use of Checklists … 66 Positive Exchange of Flight Controls … 66 Use of Distractions … 66 Aeronautical Decision-Making, Risk Management, Crew Resource Management, and Single-Pilot

Resource Management … 66 Multi-Powerplant Considerations … 67

Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations

Aircraft Requirements & Limitations … 68 Equipment Requirements & Limitations … 68 Use of Flight Simulation Training Devices (FSTD) … 68 Credit for Pilot Time in an FSTD … 68 Use of Aviation Training Devices (ATD) … 68 Credit for Pilot Time in an ATD … 68 Operational Requirements, Limitations, & Task Information … 69

Introduction › Use of the Term “Flight Manual”

Introduction

Airman Certification Standards Concept

The goal of the airman certification process is to ensure the applicant possesses the knowledge, ability to manage risks, and skill consistent with the privileges of the certificate or rating being exercised, in order to act as pilot-in-command (PIC).

Safe operations in today’s National Airspace System (NAS) require the integration of aeronautical knowledge, risk management, and flight proficiency standards. To accomplish these goals, the FAA drew upon the expertise of organizations and individuals across the aviation and training community to develop the ACS. The ACS integrates the elements of knowledge, risk management, and skill required for each airman certificate or rating. It thus forms a more comprehensive standard for what an applicant must know, consider, and do to demonstrate proficiency to pass the tests required for issuance of the applicable airman certificate or rating.

Use of the Term “Flight Manual”

Throughout this document, the term “flight manual” refers to the approved powered-lift aircraft flight manual.

.

Area of Operation I. Preflight Preparation › Task B. Airworthiness Requirements

Area of Operation I. Preflight Preparation

Area of Operation I. Preflight Preparation

Task A. Pilot Qualifications

eferences: R 14 CFR parts 61, 68, 91, 119.1(e); AC 68-1; FAA-H-8083-2, FAA-H-8083-25

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with airman and medical certificates including privileges, limitations, currency, and operating as pilot-incommand as a commercial pilot.

Knowledge: The applicant demonstrates understanding of:

CP.I.A.K1 Certification requirements, recent flight experience, and recordkeeping.

CP.I.A.K2 Privileges and limitations.

CP.I.A.K3 Medical certificates: class, expiration, privileges, temporary disqualifications.

CP.I.A.K4 Documents required to exercise commercial pilot privileges.

CP.I.A.K5 Part 68 BasicMed privileges and limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.A.R1 Proficiency versus currency.

CP.I.A.R2 Flying unfamiliar aircraft or operating with unfamiliar flight display systems and avionics.

Skills: The applicant exhibits the skill to:

CP.I.A.S1 Apply requirements to act as pilot-in-command (PIC) under Visual Flight Rules (VFR) in a scenario given by the evaluator.

Task B. Airworthiness Requirements

eferences: R 14 CFR parts 21, 39, 43, 91; FAA-H-8083-2, FAA-H-8083-25

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with airworthiness requirements, including aircraft certificates.

Knowledge: The applicant demonstrates understanding of:

CP.I.B.K1 General airworthiness requirements and compliance for aircraft, including:

CP.I.B.K1a a. Location and expiration dates of required aircraft certificates

CP.I.B.K1b b. Required inspections and aircraft logbook documentation

CP.I.B.K1c c. Airworthiness Directives and Special Airworthiness Information Bulletins

CP.I.B.K1d d. Purpose and procedure for obtaining a special flight permit

CP.I.B.K2 Pilot-performed preventive maintenance.

CP.I.B.K3 Equipment requirements for day and night VFR flight, including:

CP.I.B.K3a a. Flying with inoperative equipment

CP.I.B.K3b b. Using an approved Minimum Equipment List (MEL)

Area of Operation I. Preflight Preparation

CP.I.B.K3c c. Kinds of Operation Equipment List (KOEL)

CP.I.B.K3d d. Required discrepancy records or placards

CP.I.B.K4 Standard and special airworthiness certificates and their associated operational limitations.

Area of Operation I. Preflight Preparation › Task C. Weather Information

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.B.R1 Inoperative equipment discovered prior to flight.

Skills: The applicant exhibits the skill to:

CP.I.B.S1 Locate and describe aircraft airworthiness and registration information.

CP.I.B.S2 Determine the aircraft is airworthy in the scenario given by the evaluator.

CP.I.B.S3 Apply appropriate procedures for operating with inoperative equipment in the scenario given by the evaluator.

Task C. Weather Information

eferences: R 14 CFR part 91; AC 91-92; AIM; FAA-H-8083-2, FAA-H-8083-25, FAA-H-8083-28

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with weather information for a flight under VFR.

ote: N If K2 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.

ote: N If K3 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.

Knowledge: The applicant demonstrates understanding of:

CP.I.C.K1 Sources of weather data (e.g., National Weather Service, Flight Service) for flight planning purposes.

CP.I.C.K2 Acceptable weather products and resources required for preflight planning, current and forecast weather for departure, en route, and arrival phases of flight such as:

CP.I.C.K2a a. Airport Observations (METAR and SPECI) and Pilot Observations (PIREP)

CP.I.C.K2b b. Surface Analysis Chart, Ceiling and Visibility Chart (CVA)

CP.I.C.K2c c. Terminal Aerodrome Forecasts (TAF)

CP.I.C.K2d d. Graphical Forecasts for Aviation (GFA)

CP.I.C.K2e e. Wind and Temperature Aloft Forecast (FB)

CP.I.C.K2f f. Convective Outlook (AC)

CP.I.C.K2g g. Inflight Aviation Weather Advisories including Airmen's Meteorological Information (AIRMET),

Significant Meteorological Information (SIGMET), and Convective SIGMET

CP.I.C.K3 Meteorology applicable to the departure, en route, alternate, and destination under visual flight rules (VFR) in Visual Meteorological Conditions (VMC), including expected climate and hazardous conditions such as:

CP.I.C.K3a a. Atmospheric composition and stability

CP.I.C.K3b b. Wind (e.g., windshear, mountain wave, factors affecting wind, etc.)

CP.I.C.K3c c. Temperature and heat exchange

Area of Operation I. Preflight Preparation

CP.I.C.K3d d. Moisture/precipitation

CP.I.C.K3e e. Weather system formation, including air masses and fronts

CP.I.C.K3f f. Clouds

Area of Operation I. Preflight Preparation › Task D. Cross-Country Flight Planning

CP.I.C.K3g g. Turbulence

CP.I.C.K3h h. Thunderstorms and microbursts

CP.I.C.K3i i. Icing and freezing level information

CP.I.C.K3j j. Fog/mist

CP.I.C.K3k k. Frost

CP.I.C.K3l l. Obstructions to visibility (e.g., smoke, haze, volcanic ash, etc.)

CP.I.C.K4 Flight deck instrument displays of digital weather and aeronautical information.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.C.R1 Making the go/no-go and continue/divert decisions, including:

CP.I.C.R1a a. Circumstances that would make diversion prudent

CP.I.C.R1b b. Personal weather minimums

CP.I.C.R1c c. Hazardous weather conditions, including known or forecast icing or turbulence aloft

CP.I.C.R2 Use and limitations of:

CP.I.C.R2a a. Installed onboard weather equipment

CP.I.C.R2b b. Aviation weather reports and forecasts

CP.I.C.R2c c. Inflight weather resources

Skills: The applicant exhibits the skill to:

CP.I.C.S1 Use available aviation weather resources to obtain an adequate weather briefing.

CP.I.C.S2 Analyze the implications of at least three of the conditions listed in K3a through K3l, using actual weather or weather conditions provided by the evaluator.

CP.I.C.S3 Correlate weather information to make a go/no-go decision.

Task D. Cross-Country Flight Planning

eferences: R 14 CFR part 91; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; NOTAMs; VFR Navigation Charts

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with cross-country flights and VFR flight planning.

ote: N Preparation, presentation, and explanation of a computer-generated flight plan is an acceptable option.

Knowledge: The applicant demonstrates understanding of:

CP.I.D.K1 Route planning, including consideration of different classes and special use airspace (SUA) and selection of appropriate and available navigation/communication systems and facilities.

Area of Operation I. Preflight Preparation › Task E. National Airspace System

Area of Operation I. Preflight Preparation

CP.I.D.K1a a. Use of an electronic flight bag (EFB), if used

CP.I.D.K2 Altitude selection accounting for terrain and obstacles, glide or autorotative distance of the aircraft, VFR cruising altitudes, and the effect of wind.

CP.I.D.K3 Calculating:

CP.I.D.K3a a. Time, climb and descent rates, course, distance, heading, true airspeed, and groundspeed

CP.I.D.K3b b. Estimated time of arrival, including conversion to universal coordinated time (UTC)

CP.I.D.K3c c. Fuel requirements, including reserve

CP.I.D.K4 Elements of a VFR flight plan.

CP.I.D.K5 Procedures for filing, activating, and closing a VFR flight plan.

CP.I.D.K6 Inflight intercept procedures.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.D.R1 Pilot.

CP.I.D.R2 Aircraft.

CP.I.D.R3 Environment (e.g., weather, airports, airspace, terrain, obstacles, including wire strike hazards).

CP.I.D.R4 External pressures.

CP.I.D.R5 Limitations of air traffic control (ATC) services.

CP.I.D.R6 Fuel planning.

CP.I.D.R7 Use of an electronic flight bag (EFB), if used.

Skills: The applicant exhibits the skill to:

CP.I.D.S1 Prepare, present, and explain a cross-country flight plan assigned by the evaluator, including a risk analysis based on real-time weather, to the first fuel stop.

CP.I.D.S2 Apply pertinent information from appropriate and current aeronautical charts, Chart Supplements; Notices to Air Missions (NOTAMs) relative to airport/heliport/helipad/landing area, runway and taxiway closures; and other flight publications.

CP.I.D.S3 Create a navigation log and prepare a VFR flight plan.

CP.I.D.S4 Recalculate fuel reserves based on a scenario provided by the evaluator.

CP.I.D.S5 Use an electronic flight bag (EFB), if applicable.

Task E. National Airspace System

eferences: R 14 CFR parts 71, 91, 93; AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with National Airspace System (NAS) operations under VFR as a commercial pilot.

Knowledge: The applicant demonstrates understanding of:

CP.I.E.K1 Airspace classes and associated requirements and limitations.

Area of Operation I. Preflight Preparation

CP.I.E.K2 Chart symbols.

CP.I.E.K3 Special use airspace (SUA), special flight rules areas (SFRA), temporary flight restrictions (TFR), and other airspace areas.

Area of Operation I. Preflight Preparation › Task F. Performance and Limitations

CP.I.E.K4 Special visual flight rules (VFR) requirements.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.E.R1 Various classes and types of airspace.

Skills: The applicant exhibits the skill to:

CP.I.E.S1 Identify and comply with the requirements for basic VFR weather minimums and flying in particular classes of airspace.

CP.I.E.S2 Correctly identify airspace and operate in accordance with associated communication and equipment requirements.

CP.I.E.S3 Identify the requirements for operating in SUA or within a TFR. Identify and comply with special air traffic rules (SATR) and SFRA operations, if applicable.

Task F. Performance and Limitations

eferences: R FAA-H-8083-1, FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with operating an aircraft within the parameters of its performance capabilities and limitations.

Knowledge: The applicant demonstrates understanding of:

CP.I.F.K1 Elements related to performance and limitations by explaining the use of charts, tables, and data to determine performance.

CP.I.F.K2 Factors affecting performance, including:

CP.I.F.K2a a. Atmospheric conditions

CP.I.F.K2b b. Pilot technique

CP.I.F.K2c c. Aircraft configuration

CP.I.F.K2d d. Airport, heliport, helipad, or unprepared surface environment

CP.I.F.K2e e. Loading [e.g., center of gravity (CG)]

CP.I.F.K2f f. Weight and balance

CP.I.F.K3 Aerodynamics.

CP.I.F.K4 Height/Velocity (H/V) diagram according to the flight manual.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.F.R1 Use of performance charts, tables, and data.

CP.I.F.R2 Aircraft limitations.

Area of Operation I. Preflight Preparation › Task G. Operation of Systems

Area of Operation I. Preflight Preparation

CP.I.F.R3 Possible differences between calculated performance and actual performance.

CP.I.F.R4 Operations within “avoid areas” of the H/V diagram.

CP.I.F.R5 Other hazards specific to the powered-lift make and model.

Skills: The applicant exhibits the skill to:

CP.I.F.S1 Compute the weight and balance, correct out-of-center of gravity loading errors and determine if the weight and balance remains within limits during all phases of flight and aircraft configurations.

CP.I.F.S2 Use of the appropriate manufacturer’s approved performance charts, tables, and data.

Task G. Operation of Systems

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with safe operation of systems on the aircraft provided for the flight test.

ote: N If K1 is selected, the evaluator must assess the applicant's knowledge of at least three sub-elements.

Knowledge: The applicant demonstrates understanding of:

CP.I.G.K1 Aircraft systems, including:

CP.I.G.K1a a. Primary flight controls

CP.I.G.K1b b. Secondary flight controls

CP.I.G.K1c c. Powerplant(s) and means of producing thrust

CP.I.G.K1d d. Landing gear

CP.I.G.K1e e. Fuel, oil, and hydraulic

CP.I.G.K1f f. Electrical

CP.I.G.K1g g. Avionics

CP.I.G.K1h h. Pitot-static, vacuum/pressure, and associated flight instruments

CP.I.G.K1i i. Environmental

CP.I.G.K1j j. Deicing and anti-icing

CP.I.G.K1k k. Oxygen system

CP.I.G.K1l l. Gearboxes, drive shafts, transmission systems, as applicable

CP.I.G.K1m m. Battery(s) used for propulsion–charging, discharging, and condition, as applicable

CP.I.G.K2 Indications of and procedures for managing system abnormalities or failures.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.G.R1 Detection of system malfunctions or failures.

CP.I.G.R2 Management of a system failure.

CP.I.G.R3 Monitoring and management of automated systems.

Area of Operation I. Preflight Preparation › Task H. Human Factors

Area of Operation I. Preflight Preparation

Skills: The applicant exhibits the skill to:

CP.I.G.S1 Operate at least three of the systems listed in K1a through K1m appropriately.

CP.I.G.S2 Complete the appropriate checklist(s).

Task H. Human Factors

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with personal health, flight physiology, and aeromedical and human factors related to safety of flight.

Knowledge: The applicant demonstrates understanding of:

CP.I.H.K1 Symptoms, recognition, causes, effects, and corrective actions associated with aeromedical and physiological issues, including:

CP.I.H.K1a a. Hypoxia

CP.I.H.K1b b. Hyperventilation

CP.I.H.K1c c. Middle ear and sinus problems

CP.I.H.K1d d. Spatial disorientation

CP.I.H.K1e e. Motion sickness

CP.I.H.K1f f. Carbon monoxide poisoning

CP.I.H.K1g g. Stress

CP.I.H.K1h h. Fatigue

CP.I.H.K1i i. Dehydration and nutrition

CP.I.H.K1j j. Hypothermia

CP.I.H.K1k k. Optical illusions

CP.I.H.K1l l. Dissolved nitrogen in the bloodstream after scuba dives

CP.I.H.K2 Regulations regarding use of alcohol and drugs.

CP.I.H.K3 Effects of alcohol, drugs, and over-the-counter medications.

CP.I.H.K4 Aeronautical Decision-Making (ADM) to include using Crew Resource Management (CRM) or Single- Pilot Resource Management (SRM), as appropriate.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.H.R1 Aeromedical and physiological issues.

CP.I.H.R2 Hazardous attitudes.

CP.I.H.R3 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.I.H.R4 Confirmation and expectation bias.

Skills: The applicant exhibits the skill to:

Area of Operation I. Preflight Preparation › Task I. Night Operations

Area of Operation I. Preflight Preparation

CP.I.H.S1 Associate the symptoms and effects for at least three of the conditions listed in K1a through K1l with the cause(s) and corrective action(s).

CP.I.H.S2 Perform self-assessment, including fitness for flight and personal minimums, for actual flight or a scenario given by the evaluator.

Task I. Night Operations

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with night preparation and flight.

Knowledge: The applicant demonstrates understanding of:

CP.I.I.K1 Physiological aspects of vision related to night flying.

CP.I.I.K2 Required aircraft equipment and lighting for night operations.

CP.I.I.K3 Personal equipment essential for night flight.

CP.I.I.K4 Night orientation, navigation, chart reading techniques and methods for maintaining night vision effectiveness.

CP.I.I.K5 Visual illusions at night.

CP.I.I.K6 Lighting systems identifying airports/heliports/helipads/landing areas, runways, taxiways and obstructions, as well as pilot controlled lighting.

CP.I.I.K7 Interpretation of traffic position and direction based solely on position lights.

CP.I.I.K8 Night taxi operations.

CP.I.I.K9 Appropriate use of automation, if applicable.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.I.I.R1 Collision hazards.

CP.I.I.R2 Runway incursion.

CP.I.I.R3 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.I.I.R4 Effect of visual illusions and night adaptation during all phases of night flying.

CP.I.I.R5 Night currency versus proficiency.

CP.I.I.R6 Weather considerations specific to night operations.

CP.I.I.R7 Inoperative equipment.

Skills: The applicant exhibits the skill to:

CP.I.I.S1 [Intentionally left blank].

Area of Operation II. Preflight Procedures › Task B. Flight Deck Management

Area of Operation II. Preflight Procedures

Area of Operation II. Preflight Procedures

Task A. Preflight Assessment

eferences: R FAA-H-8083-2, FAA-H-8083-25, FAA-H-8083-28; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with preparation for safe flight.

Knowledge: The applicant demonstrates understanding of:

CP.II.A.K1 Pilot self-assessment.

CP.II.A.K2 Determining that the aircraft to be used is airworthy.

CP.II.A.K3 Aircraft preflight inspection, including:

CP.II.A.K3a a. Which items should be inspected

CP.II.A.K3b b. The reasons for checking each item

CP.II.A.K3c c. How to detect possible defects

CP.II.A.K3d d. The associated regulations

CP.II.A.K4 Environmental factors, including weather, terrain, route selection, and obstructions.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.II.A.R1 Pilot.

CP.II.A.R2 Aircraft.

CP.II.A.R3 Environment (e.g., weather, icing, airports/heliports/helipads/landing areas, airspace, terrain, obstacles).

CP.II.A.R4 External pressures.

CP.II.A.R5 Aviation security concerns.

Skills: The applicant exhibits the skill to:

CP.II.A.S1 Inspect the aircraft with reference to an appropriate checklist.

CP.II.A.S2 Verify the aircraft is in condition for safe flight and conforms to its type design.

CP.II.A.S3 Perform self-assessment.

CP.II.A.S4 Continue to assess the environment for safe flight.

Task B. Flight Deck Management

eferences: R 14 CFR part 91; AC 120-71; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight deck management practices.

ote: N See Appendix 2: Safety of Flight.

Knowledge: The applicant demonstrates understanding of:

Area of Operation II. Preflight Procedures › Task C. Powerplant Starting

Area of Operation II. Preflight Procedures

CP.II.B.K1 Passenger briefing requirements, including operation and required use of safety restraint systems.

CP.II.B.K2 Use of appropriate checklists.

CP.II.B.K3 Requirements for current and appropriate navigation data.

CP.II.B.K4 Securing items and cargo.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.II.B.R1 Use of systems or equipment, including automation and portable electronic devices.

CP.II.B.R2 Inoperative equipment.

CP.II.B.R3 Passenger distractions.

Skills: The applicant exhibits the skill to:

CP.II.B.S1 Secure all items in the aircraft.

CP.II.B.S2 Conduct an appropriate passenger briefing, including identifying the pilot-in-command (PIC), use of safety belts, shoulder harnesses, doors, sterile aircraft, passenger conduct and avoidance of rotor or air induction systems, powerplants, and other heat sources, and emergency procedures.

CP.II.B.S3 Properly program and manage the aircraft’s automation, as applicable.

CP.II.B.S4 Appropriately manage risks by utilizing ADM, including SRM/CRM.

Task C. Powerplant Starting

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with recommended powerplant starting procedures.

Knowledge: The applicant demonstrates understanding of:

CP.II.C.K1 Starting under various conditions.

CP.II.C.K2 Starting procedures, including the use of external power if applicable.

CP.II.C.K3 Limitations associated with starting.

CP.II.C.K4 Conditions leading to and procedures for an aborted start.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.II.C.R1 Use of external power unit.

CP.II.C.R2 Limitations during starting.

CP.II.C.R3 Other hazards specific to the powered-lift make and model.

Skills: The applicant exhibits the skill to:

CP.II.C.S1 Position the aircraft properly considering structures, other aircraft, wind, and the safety of nearby persons and property.

Area of Operation II. Preflight Procedures › Task D. Ground Taxiing

Area of Operation II. Preflight Procedures

CP.II.C.S2 Complete the appropriate checklist(s).

CP.II.C.S3 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.

CP.II.C.S4 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task D. Ground Taxiing

eferences: R AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with ground taxi operations, in a wheel-type aircraft, including runway incursion avoidance.

Knowledge: The applicant demonstrates understanding of:

CP.II.D.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).

CP.II.D.K2 Taxi instructions/clearances.

CP.II.D.K3 Airport, heliport, helipad, or unprepared surface environment.

CP.II.D.K4 Visual indicators for wind.

CP.II.D.K5 Aircraft lighting, as appropriate.

CP.II.D.K6 Procedures for:

CP.II.D.K6a a. Appropriate flight deck activities prior to taxi, including route planning and identifying the

location of Hot Spots

CP.II.D.K6b b. Aircraft configuration

CP.II.D.K6c c. Radio communications at towered and non-towered airports/heliports/helipads/landing areas

CP.II.D.K6d d. Entering or crossing runways

CP.II.D.K6e e. Night taxi operations

CP.II.D.K6f f. Taxi limitations

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.II.D.R1 Activities and distractions.

CP.II.D.R2 Confirmation or expectation bias as related to taxi instructions.

CP.II.D.R3 A taxi route or departure runway change.

CP.II.D.R4 Speed during taxi and turns.

CP.II.D.R5 Appropriate thrust vector and brake use.

CP.II.D.R6 Airframe and rotor clearances during taxi.

CP.II.D.R7 Runway incursion.

CP.II.D.R8 Other hazards specific to the powered-lift make and model.

Skills: The applicant exhibits the skill to:

Area of Operation II. Preflight Procedures › Task E. Before Takeoff Check

Area of Operation II. Preflight Procedures

CP.II.D.S1 Receive and correctly read back clearances/instructions, if applicable.

CP.II.D.S2 Use an appropriate airport/heliport diagram or taxi chart, if published.

CP.II.D.S3 Position the flight controls and configure the aircraft for the existing wind conditions.

CP.II.D.S4 Complete the appropriate checklist(s).

CP.II.D.S5 Maintain positive control of the aircraft during ground operations by controlling direction and speed without excessive use of brakes.

CP.II.D.S6 Comply with airport/heliport/helipad/landing area taxiway markings, signals, and air traffic control (ATC) clearances and instructions.

CP.II.D.S7 Position the aircraft relative to hold lines or a specified point.

CP.II.D.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task E. Before Takeoff Check

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with before takeoff check.

Knowledge: The applicant demonstrates understanding of:

CP.II.E.K1 Purpose of before takeoff checklist items, including:

CP.II.E.K1a a. Reasons for checking each item

CP.II.E.K1b b. Detecting malfunctions

CP.II.E.K1c c. Configuring the aircraft as recommended by the manufacturer

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.II.E.R1 Division of attention while conducting before takeoff checks.

CP.II.E.R2 Unexpected runway changes.

CP.II.E.R3 Unexpected or unclear clearances from ATC.

CP.II.E.R4 Wake turbulence.

CP.II.E.R5 Downwash.

CP.II.E.R6 Potential powerplant failure during takeoff or other malfunction considering operational factors such as aircraft characteristics, runway/takeoff path length, surface conditions, environmental conditions, and obstructions.

Skills: The applicant exhibits the skill to:

CP.II.E.S1 Review takeoff performance.

CP.II.E.S2 Select the appropriate takeoff profile for aircraft and environmental conditions.

CP.II.E.S3 Complete the appropriate checklist(s).

CP.II.E.S4 Properly position the aircraft considering other aircraft, vessels, and wind.

Area of Operation II. Preflight Procedures

CP.II.E.S5 Divide attention inside and outside the aircraft.

CP.II.E.S6 Verify that powerplant parameters and aircraft configuration are suitable for the takeoff profile.

CP.II.E.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation III. Airport and Heliport Operations › Task B. Runway/Taxiway/Heliport/Helipad Signs, Markings, and Lighting

Area of Operation III. Airport and Heliport Operations

Area of Operation III. Airport and Heliport Operations

Task A. Communications, Light Signals, and Runway Lighting Systems

eferences: R 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-25

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal and emergency radio communications, air traffic control (ATC) light signals, and runway lighting systems.

Knowledge: The applicant demonstrates understanding of:

CP.III.A.K1 How to obtain appropriate radio frequencies.

CP.III.A.K2 Proper radio communication procedures and air traffic control (ATC) phraseology.

CP.III.A.K3 ATC light signal recognition.

CP.III.A.K4 Appropriate use of transponder(s).

CP.III.A.K5 Lost communication procedures.

CP.III.A.K6 Equipment issues that could cause loss of communication.

CP.III.A.K7 Radar assistance.

CP.III.A.K8 National Transportation Safety Board (NTSB) accident/incident reporting.

CP.III.A.K9 Runway Status Lighting Systems.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.III.A.R1 Communication.

CP.III.A.R2 Deciding if and when to declare an emergency.

CP.III.A.R3 Use of non-standard phraseology.

Skills: The applicant exhibits the skill to:

CP.III.A.S1 Select and activate appropriate frequencies.

CP.III.A.S2 Transmit using standard phraseology and procedures as specified in the Aeronautical Information Manual (AIM) and Pilot/Controller Glossary.

CP.III.A.S3 Acknowledge radio communications and comply with ATC instructions or as directed by the evaluator.

Task B. Runway/Taxiway/Heliport/Helipad Signs, Markings, and Lighting

eferences: R 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-25

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with runway/taxiway/heliport/helipad signs, markings and lighting.

Knowledge: The applicant demonstrates understanding of:

CP.III.B.K1 Airport runway, heliport, helipad, taxiway signs, markings, and lighting.

CP.III.B.K2 Airport movement area.

Area of Operation III. Airport and Heliport Operations › Task C. Traffic Patterns

Area of Operation III. Airport and Heliport Operations

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.III.B.R1 Interpretation of signs, markings, or lighting.

CP.III.B.R2 Landing site dimensions and limitations.

CP.III.B.R3 Conflict with aircraft, vehicles, and persons.

CP.III.B.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.III.B.R5 Powered-lift configuration, including the effect of thrust on other aircraft.

Skills: The applicant exhibits the skill to:

CP.III.B.S1 Comply with airport/heliport/helipad signs, markings, and lighting encountered, as applicable to the aircraft provided for the practical test.

Task C. Traffic Patterns

eferences: R 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-25

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with traffic patterns.

Knowledge: The applicant demonstrates understanding of:

CP.III.C.K1 Towered and nontowered airport/heliport/helipad/landing area operations and restrictions.

CP.III.C.K2 Runway selection and traffic pattern parameters for the current conditions.

CP.III.C.K3 Right-of-way rules.

CP.III.C.K4 Use of automated weather and airport/heliport information.

CP.III.C.K5 Aircraft configuration and selection for the traffic pattern in use.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.III.C.R1 Collision hazards.

CP.III.C.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.III.C.R3 Windshear and wake turbulence.

Skills: The applicant exhibits the skill to:

CP.III.C.S1 Identify and interpret airport/heliport/helipad/landing area runways, taxiways, markings, signs, and lighting.

CP.III.C.S2 Comply with recommended traffic pattern procedures.

CP.III.C.S3 Correct for wind drift to maintain the proper ground track.

CP.III.C.S4 Maintain orientation with the runway/landing area in use.

CP.III.C.S5 Maintain traffic pattern altitude, ±100 feet, and the appropriate airspeed, ±10 knots.

CP.III.C.S6 Maintain situational awareness and proper spacing from other aircraft in the traffic pattern.

Area of Operation III. Airport and Heliport Operations

CP.III.C.S7 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.

CP.III.C.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation IV. Hovering Maneuvers › Task B. Hover Taxi

Area of Operation IV. Hovering Maneuvers

Area of Operation IV. Hovering Maneuvers

Task A. Vertical Takeoff and Landing

eferences: R 14 CFR part 91; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with vertical takeoff and landing from a hover.

Knowledge: The applicant demonstrates understanding of:

CP.IV.A.K1 Elements related to a vertical takeoff to a hover and landing from a hover.

CP.IV.A.K2 Appropriate aircraft configuration for a stationary hover.

CP.IV.A.K3 Effect of wind on flight control inputs.

CP.IV.A.K4 Ground effect.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IV.A.R1 Obstacle and hazard avoidance.

CP.IV.A.R2 Dynamic rollover.

CP.IV.A.R3 Powerplant failure during hover.

CP.IV.A.R4 Downwash.

CP.IV.A.R5 Ground resonance.

Skills: The applicant exhibits the skill to:

CP.IV.A.S1 Complete the appropriate checklist(s).

CP.IV.A.S2 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.

CP.IV.A.S3 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.

CP.IV.A.S4 Ascend to and maintain recommended hovering altitude, and descend from recommended hovering altitude in headwind, crosswind, and tailwind conditions, without drift.

CP.IV.A.S5 Maintain recommended hovering altitude, ±1/2 of that altitude within 10 feet of the surface, if above 10 feet, ±5 feet.

CP.IV.A.S6 Maintain position within ±2 feet of a designated point.

CP.IV.A.S7 Descend vertically to within 2 feet of the designated touchdown point.

CP.IV.A.S8 Maintain headings ±10°, as specified by the evaluator.

CP.IV.A.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task B. Hover Taxi

eferences: R AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with hover taxi operations, including runway incursion avoidance.

Area of Operation IV. Hovering Maneuvers

Knowledge: The applicant demonstrates understanding of:

CP.IV.B.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).

CP.IV.B.K2 Hover taxi instructions, clearances, and limitations.

CP.IV.B.K3 Airport/heliport/helipad/landing area, signs, markings, and lighting.

CP.IV.B.K4 Visual indicators for wind.

CP.IV.B.K5 Aircraft lighting, as appropriate.

CP.IV.B.K6 Procedures for:

CP.IV.B.K6a a. Pilot activities during taxiing

CP.IV.B.K6b b. Safe hover taxi at towered and non-towered airports/heliports/helipads/landing areas

CP.IV.B.K6c c. Entering or crossing runways

CP.IV.B.K7 Aircraft configuration.

CP.IV.B.K8 Aircraft operating limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IV.B.R1 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.IV.B.R2 Reduced visibility or night taxi operations.

CP.IV.B.R3 Powerplant(s) failure during hover taxi.

CP.IV.B.R4 Other aircraft and hazards.

CP.IV.B.R5 Hazardous effects of downwash.

CP.IV.B.R6 Aircraft configuration.

CP.IV.B.R7 Height/Velocity (H/V) considerations.

CP.IV.B.R8 Crosswind limitations.

CP.IV.B.R9 Other hazards specific to the powered-lift make and model.

CP.IV.B.R10 Runway incursion.

Skills: The applicant exhibits the skill to:

CP.IV.B.S1 Complete the appropriate checklist(s).

CP.IV.B.S2 Receive and correctly read back clearances/instructions, if applicable.

CP.IV.B.S3 Use an airport diagram or taxi chart during taxi, if published, and maintain situational awareness.

CP.IV.B.S4 Comply with airport/heliport taxiway markings, signals, and signs.

CP.IV.B.S5 Position the primary flight controls, including the thrust vector, for the prevailing environmental conditions.

CP.IV.B.S6 Hover taxi over specified ground references, demonstrating forward, sideward, and rearward hovering and hovering turns.

Area of Operation IV. Hovering Maneuvers

CP.IV.B.S7 Maintain recommended hovering altitude, ±1/2 of that altitude within 10 feet of the surface, if above 10 feet, ±5 feet.

Area of Operation IV. Hovering Maneuvers › Task C. Air Taxi

CP.IV.B.S8 Make 90°, 180°, and 360° pivoting turns, stopping within 10° of specified headings.

CP.IV.B.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task C. Air Taxi

eferences: R AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with air taxi operations.

Knowledge: The applicant demonstrates understanding of:

CP.IV.C.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).

CP.IV.C.K2 Air taxi instructions, clearances, and limitations.

CP.IV.C.K3 Aircraft configuration.

CP.IV.C.K4 Airport/heliport/helipad/landing area, signs, markings, and lighting.

CP.IV.C.K5 Visual indicators for wind.

CP.IV.C.K6 Aircraft lighting, as appropriate.

CP.IV.C.K7 Procedures for:

CP.IV.C.K7a a. Pilot activities during taxiing

CP.IV.C.K7b b. Safe air taxi at towered and non-towered airports/heliports/helipads/landing areas

CP.IV.C.K7c c. Overflying of runways

CP.IV.C.K8 Aircraft operating limitations.

CP.IV.C.K9 Appropriate height and speed for air taxi.

CP.IV.C.K10 Height/Velocity (H/V) considerations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IV.C.R1 Activities and distractions.

CP.IV.C.R2 Reduced visibility or night taxi operations.

CP.IV.C.R3 H/V diagram performance in case of powerplant failure.

CP.IV.C.R4 Other aircraft and hazards.

CP.IV.C.R5 Runway incursion.

Skills: The applicant exhibits the skill to:

CP.IV.C.S1 Complete the appropriate checklist(s).

CP.IV.C.S2 Use an airport diagram or taxi chart during taxi, if published, and maintain situational awareness.

Area of Operation IV. Hovering Maneuvers

CP.IV.C.S3 Select a safe airspeed and altitude.

CP.IV.C.S4 Maintain an appropriate aircraft configuration throughout the maneuver.

CP.IV.C.S5 Maintain specified altitude, ±10 feet.

CP.IV.C.S6 Air taxi from one point to another under various wind conditions.

CP.IV.C.S7 Maintain the aircraft within operating limits throughout the maneuver.

CP.IV.C.S8 Comply with airport/heliport/helipad/landing area markings, lights, signs, and ATC instructions.

CP.IV.C.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation V. Takeoffs, Landings, and Go-Arounds

Area of Operation V. Takeoffs, Landings, and Go-Arounds

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task A. Normal Takeoff and Climb from a Hover

ote: N Select all applicable tasks in accordance with the aircraft's operating characteristics as specified in the flight manual.

Task A. Normal Takeoff and Climb from a Hover

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal takeoff and climb from a hover.

ote: N If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.

Knowledge: The applicant demonstrates understanding of:

CP.V.A.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.

CP.V.A.K2 Recommended takeoff and climb profiles.

CP.V.A.K3 Aircraft configuration.

CP.V.A.K4 Factors affecting the profile of the height/velocity (H/V) diagram.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.A.R1 Selection of helipad/deck, runway, or departure point based on aircraft performance and limitations, available distance, and wind.

CP.V.A.R2 Effects of:

CP.V.A.R2a a. Crosswind

CP.V.A.R2b b. Windshear

CP.V.A.R2c c. Tailwind

CP.V.A.R2d d. Wake turbulence

CP.V.A.R2e e. Runway/departure point surface/condition

CP.V.A.R2f f. Aircraft weight

CP.V.A.R3 Abnormal operations including:

CP.V.A.R3a a. Rejected takeoff

CP.V.A.R3b b. Powerplant failure in hover/takeoff/climb phase of flight

CP.V.A.R4 Collision hazards.

CP.V.A.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

CP.V.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.V.A.R7 Runway incursion.

Skills: The applicant exhibits the skill to:

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task B. Rolling Takeoff and Climb

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.A.S1 Complete the appropriate checklist(s).

CP.V.A.S2 Make radio calls as appropriate.

CP.V.A.S3 Verify assigned/correct runway, if at an airport.

CP.V.A.S4 Determine wind direction with or without visible wind direction indicators.

CP.V.A.S5 Position the flight controls and configure the aircraft for the existing wind conditions.

CP.V.A.S6 Clear the area, ground or hover taxi into takeoff position, and hover the aircraft above the departure point, aligned with the departure path.

CP.V.A.S7 Confirm takeoff power and instrument indications prior to forward movement.

CP.V.A.S8 Takeoff and accelerate to the manufacturer’s recommended speed.

CP.V.A.S9 After takeoff, establish and maintain a positive rate of climb and configure aircraft, as appropriate.

CP.V.A.S10 Maintain the aircraft within operating limits throughout the maneuver.

CP.V.A.S11 Maintain VY ±5 knots to a safe maneuvering altitude.

CP.V.A.S12 Maintain directional control and proper wind-drift correction throughout takeoff and climb.

CP.V.A.S13 Comply with noise abatement procedures, as applicable.

CP.V.A.S14 Use runway incursion avoidance procedures, if applicable.

Task B. Rolling Takeoff and Climb

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with rolling takeoff with wheel-type landing gear.

ote: N If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.

Knowledge: The applicant demonstrates understanding of:

CP.V.B.K1 Elements related to a rolling takeoff and the purpose of the maneuver.

CP.V.B.K2 Aircraft configurations.

CP.V.B.K3 Effects of wind, weight, temperature, and density altitude.

CP.V.B.K4 Translational lift.

CP.V.B.K5 Takeoff and climb performance and the height velocity (H/V) diagram.

CP.V.B.K6 Aircraft performance and limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.B.R1 Collision hazards.

CP.V.B.R2 Powerplant failure during rolling takeoff and climb out.

CP.V.B.R3 Aircraft configuration.

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.B.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.V.B.R5 Effects of:

CP.V.B.R5a a. Crosswind

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task C. Maximum Performance Takeoff and Climb

CP.V.B.R5b b. Windshear

CP.V.B.R5c c. Tailwind

CP.V.B.R5d d. Wake turbulence

CP.V.B.R5e e. Runway/departure point surface/condition

CP.V.B.R5f f. Aircraft weight

CP.V.B.R6 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

Skills: The applicant exhibits the skill to:

CP.V.B.S1 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.

CP.V.B.S2 Complete the appropriate checklist(s).

CP.V.B.S3 Configure the aircraft correctly regarding environmental conditions and aircraft loading.

CP.V.B.S4 Maintain the aircraft within operating limits throughout the maneuver.

CP.V.B.S5 Maintain proper ground track with crosswind correction, if necessary.

CP.V.B.S6 Maintain a positive rate of climb.

CP.V.B.S7 Transition to recommended climb airspeed ±5 knots.

CP.V.B.S8 Use runway incursion avoidance procedures, if applicable.

CP.V.B.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task C. Maximum Performance Takeoff and Climb

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with maximum performance takeoff and climb.

Knowledge: The applicant demonstrates understanding of:

CP.V.C.K1 Situations where this maneuver is appropriate.

CP.V.C.K2 Effects of atmospheric conditions, including wind and temperature, on takeoff and climb performance.

CP.V.C.K3 Appropriate aircraft configuration, takeoff, and climb profiles.

CP.V.C.K4 Factors affecting the profile of the height/velocity (H/V) diagram.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.C.R1 Selection of takeoff path based on aircraft performance and limitations, available distance, and wind.

CP.V.C.R2 Effects of:

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task D. Normal Approach to a Hover

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.C.R2a a. Crosswind

CP.V.C.R2b b. Windshear

CP.V.C.R2c c. Tailwind

CP.V.C.R2d d. Low level turbulence

CP.V.C.R2e e. Surface conditions

CP.V.C.R3 Abnormal operations including:

CP.V.C.R3a a. Rejected takeoff

CP.V.C.R3b b. Powerplant failure in takeoff/climb phase of flight

CP.V.C.R4 Collision hazards.

CP.V.C.R5 Low altitude maneuvering, including controlled flight into terrain (CFIT).

CP.V.C.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.V.C.S1 Complete the appropriate checklist(s).

CP.V.C.S2 Make radio calls as appropriate.

CP.V.C.S3 Determine wind direction with or without visible wind direction indicators.

CP.V.C.S4 Position the flight controls and configure the aircraft for the existing wind conditions.

CP.V.C.S5 Clear the area, taxi into takeoff position, utilizing maximum available takeoff area and align the aircraft on the takeoff path.

CP.V.C.S6 Confirm takeoff power and proper powerplant and flight instrument indications prior to takeoff.

CP.V.C.S7 Establish and maintain the most efficient lift-off attitude/configuration for obstacle clearance.

CP.V.C.S8 Maintain the recommended airspeed and aircraft configuration until the obstacle is cleared.

CP.V.C.S9 After clearing the obstacle, establish pitch attitude and aircraft configuration for VY and accelerate to and maintain VY ±5 knots during the climb.

CP.V.C.S10 Reconfigure the aircraft after a positive rate of climb has been verified or in accordance with the aircraft manufacturer's guidance.

CP.V.C.S11 Maintain directional control and proper wind-drift correction throughout takeoff and climb.

CP.V.C.S12 Comply with noise abatement procedures.

CP.V.C.S13 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

CP.V.C.S14 Use runway incursion avoidance procedures, if applicable.

Task D. Normal Approach to a Hover

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with approach profile to a hover.

Knowledge: The applicant demonstrates understanding of:

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.D.K1 Types of approaches and applicability.

CP.V.D.K2 Performance data and the height velocity (H/V) diagram.

CP.V.D.K3 Effects of atmospheric conditions, including wind and density altitude, on approach and hover performance.

CP.V.D.K4 Wind correction techniques on approach and hover.

CP.V.D.K5 Aircraft configurations for the approach and hover.

CP.V.D.K6 Aircraft performance and limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.D.R1 Selection of runway/helipad/touchdown point based on aircraft performance and limitations, available distance, and wind.

CP.V.D.R2 Effects of:

CP.V.D.R2a a. Crosswind

CP.V.D.R2b b. Windshear

CP.V.D.R2c c. Tailwind

CP.V.D.R2d d. Wake turbulence

CP.V.D.R2e e. Vortex ring state (VRS)

CP.V.D.R2f f. Runway/arrival point surface/condition

CP.V.D.R3 Situations including:

CP.V.D.R3a a. Rejected landing and go-around

CP.V.D.R3b b. Powerplant failure during the approach

CP.V.D.R4 Collision hazards.

CP.V.D.R5 Flat light conditions.

CP.V.D.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.V.D.S1 Complete the appropriate checklist(s).

CP.V.D.S2 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.

CP.V.D.S3 Use the appropriate techniques and aircraft configurations through all stages of the approach.

CP.V.D.S4 Consider the wind conditions, landing surface, and obstructions and select a suitable hover point.

CP.V.D.S5 Maintain appropriate ground track with crosswind correction throughout the approach.

CP.V.D.S6 Fly a stabilized approach.

CP.V.D.S7 Arrive over the arrival point at a stabilized hover ±2 feet.

CP.V.D.S8 Execute a timely go-around for any condition that may result in an unsafe approach or landing.

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task E. Normal Approach and Landing

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.D.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

CP.V.D.S10 Use runway incursion avoidance procedures, if applicable.

Task E. Normal Approach and Landing

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a normal approach and landing.

ote: N If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.

Knowledge: The applicant demonstrates understanding of:

CP.V.E.K1 Effects of atmospheric conditions, including wind, on approach speed and angle.

CP.V.E.K2 Atmospheric factors affecting performance.

CP.V.E.K3 Use of proper thrust vector angle for transition to landing.

CP.V.E.K4 Factors affecting the profile of the height/velocity (H/V) diagram.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.E.R1 Selection of runway or takeoff path based on aircraft performance and limitations, available distance, and wind.

CP.V.E.R2 Effects of:

CP.V.E.R2a a. Crosswind

CP.V.E.R2b b. Windshear

CP.V.E.R2c c. Tailwind

CP.V.E.R2d d. Wake turbulence

CP.V.E.R2e e. Runway/heliport/helipad surface, condition, and length

CP.V.E.R3 Situations including:

CP.V.E.R3a a. Rejected landing and go-around

CP.V.E.R3b b. Powerplant failure during the approach

CP.V.E.R4 Collision hazards.

CP.V.E.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.V.E.S1 Complete the appropriate checklist(s).

CP.V.E.S2 Comply with noise abatement procedures.

CP.V.E.S3 Make radio calls as appropriate.

CP.V.E.S4 Verify assigned/correct runway/landing point if at an airport.

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task F. Steep Approach and Landing

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.E.S5 Determine wind direction with or without visible wind direction indicators.

CP.V.E.S6 Maintain proper ground track with crosswind correction, if necessary.

CP.V.E.S7 Maintain a stabilized approach profile.

CP.V.E.S8 Use manufacturer's recommended technique and remain within airspeed range allowed for each configuration change.

CP.V.E.S9 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

CP.V.E.S10 Use runway incursion avoidance procedures, if applicable.

Task F. Steep Approach and Landing

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with a steep approach to the surface.

ote: N See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

CP.V.F.K1 A stabilized steep approach.

CP.V.F.K2 Approach techniques and applicability.

CP.V.F.K3 Performance data and the height velocity (H/V) diagram.

CP.V.F.K4 Effects of atmospheric conditions on approach and landing performance.

CP.V.F.K5 Wind correction techniques.

CP.V.F.K6 Aircraft configuration.

CP.V.F.K7 Aircraft performance and limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.F.R1 Selection of the approach path and landing area.

CP.V.F.R2 Effects of:

CP.V.F.R2a a. Crosswind

CP.V.F.R2b b. Windshear

CP.V.F.R2c c. Tailwind

CP.V.F.R2d d. Wake turbulence

CP.V.F.R2e e. Vortex ring state (VRS)

CP.V.F.R2f f. Landing point condition

CP.V.F.R3 Planning for:

CP.V.F.R3a a. Rejected landing and go-around

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task G. Running/Roll-On Landing

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.F.R3b b. Powerplant failure during the approach

CP.V.F.R4 Landing in an area or in conditions where a takeoff/climb may not be possible.

CP.V.F.R5 Degraded Visual Environment (DVE) and flat light conditions.

CP.V.F.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.V.F.S1 Complete the appropriate checklist(s).

CP.V.F.S2 Position the flight controls, including the thrust vector, for the prevailing environmental conditions.

CP.V.F.S3 Maintain awareness of aircraft performance, limitations, and relative position throughout the maneuver.

CP.V.F.S4 Arrive over the touchdown point on the surface ±5 feet from intended landing point or, at the discretion of the evaluator, at a stabilized hover ±5 feet height.

CP.V.F.S5 Maintain proper ground track with crosswind correction, if necessary.

CP.V.F.S6 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

CP.V.F.S7 Use runway incursion avoidance procedures, if applicable.

Task G. Running/Roll-On Landing

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with running/roll-on landing operation.

Knowledge: The applicant demonstrates understanding of:

CP.V.G.K1 H/V diagram, if applicable.

CP.V.G.K2 Aircraft performance and limitations.

CP.V.G.K3 Aircraft configuration.

CP.V.G.K4 Effects of atmospheric conditions, including wind, on approach and landing performance.

CP.V.G.K5 Wind correction techniques on approach and landing.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.G.R1 Situations including:

CP.V.G.R1a a. Powerplant failure during approach

CP.V.G.R1b b. Rejected landing

CP.V.G.R2 Effects of:

CP.V.G.R2a a. Crosswind

CP.V.G.R2b b. Windshear

CP.V.G.R2c c. Tailwind

Area of Operation V. Takeoffs, Landings, and Go-Arounds › Task H. Go-Around/Rejected Landing

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.G.R2d d. Wake turbulence

CP.V.G.R2e e. Runway surface/condition

CP.V.G.R3 Collision hazards.

CP.V.G.R4 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

CP.V.G.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.V.G.S1 Coordinate with crew, if applicable, and complete the approach and landing checklists.

CP.V.G.S2 Ensure the aircraft is correctly configured for the landing.

CP.V.G.S3 Comply with air traffic control (ATC) or evaluator instructions and make radio calls as appropriate.

CP.V.G.S4 Maintain a ground track that ensures the desired traffic pattern flown takes into consideration obstructions and air traffic control (ATC) or evaluator instructions.

CP.V.G.S5 Ensure the aircraft is aligned with the correct/assigned runway or landing surface.

CP.V.G.S6 Consider the wind conditions, aircraft performance, landing surface, obstructions, and select a suitable touchdown point.

CP.V.G.S7 Maintain crosswind correction and directional control throughout the approach and landing.

CP.V.G.S8 Make smooth, timely, and correct control application during round out and touchdown.

CP.V.G.S9 Touch down at the appropriate speed, aircraft configuration and pitch attitude.

CP.V.G.S10 On touchdown, maintain proper ground track.

CP.V.G.S11 After touchdown, reconfigure the aircraft for surface/hover taxi.

CP.V.G.S12 Execute a timely go-around for any condition that may result in an unsafe approach or landing.

CP.V.G.S13 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

CP.V.G.S14 Use runway incursion avoidance procedures, if applicable.

Task H. Go-Around/Rejected Landing

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with go-around/rejected landing with emphasis on factors that contribute to landing conditions that may require a go-around.

Knowledge: The applicant demonstrates understanding of:

CP.V.H.K1 Situations and considerations on approach that could require a go-around/rejected landing.

CP.V.H.K2 Effects of atmospheric conditions on a go-around or rejected landing.

CP.V.H.K3 Aircraft configuration changes and techniques for the go-around.

CP.V.H.K4 Go-around/rejected landing procedures, the importance of a timely decision, and appropriate airspeeds for the maneuver.

Area of Operation V. Takeoffs, Landings, and Go-Arounds

CP.V.H.K5 Wind correction techniques.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.V.H.R1 Recognition of the need for a go-around/rejected landing.

CP.V.H.R2 Aircraft performance.

CP.V.H.R3 Application of power.

CP.V.H.R4 Aircraft configuration.

CP.V.H.R5 Collision hazards.

CP.V.H.R6 Low altitude maneuvering, including stall or controlled flight into terrain (CFIT).

CP.V.H.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.V.H.S1 Make a timely decision to go-around/reject the landing.

CP.V.H.S2 Apply the appropriate power setting for the flight condition and establish an aircraft configuration necessary to obtain the desired performance.

CP.V.H.S3 Establish a positive rate of climb and the appropriate airspeed ±10 knots.

CP.V.H.S4 Configure the aircraft, as appropriate.

CP.V.H.S5 Maintain the ground track, heading, or course appropriate for the conditions, or as specified by air traffic control (ATC) or the evaluator.

CP.V.H.S6 Notify/coordinate with air traffic control (ATC) or evaluator instructions as required.

CP.V.H.S7 Complete the appropriate checklist(s).

CP.V.H.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

CP.V.H.S9 Use runway incursion avoidance procedures, if applicable.

Area of Operation VI. Performance Maneuvers › Task B. Inflight Conversion During Straight-and-Level Flight

Area of Operation VI. Performance Maneuvers

Area of Operation VI. Performance Maneuvers

Task A. Rapid Deceleration/Quick Stop

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with rapid deceleration/quick stop and conditions that may require a rapid deceleration/quick stop.

Knowledge: The applicant demonstrates understanding of:

CP.VI.A.K1 Purpose of the maneuver.

CP.VI.A.K2 Aircraft transmission and powerplant limitations.

CP.VI.A.K3 Airspeed limitations.

CP.VI.A.K4 Aircraft maximum rate deceleration rate and technique.

CP.VI.A.K5 Height velocity (H/V) awareness.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VI.A.R1 Gaining or losing altitude.

CP.VI.A.R2 Excessive pitch attitudes.

CP.VI.A.R3 Effects of wind.

CP.VI.A.R4 Airframe and airspeed limitations.

CP.VI.A.R5 Collision hazards.

CP.VI.A.R6 Dividing attention between aircraft control and orientation.

CP.VI.A.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.VI.A.R8 Uncoordinated flight.

CP.VI.A.R9 Vortex ring state (VRS).

Skills: The applicant exhibits the skill to:

CP.VI.A.S1 Complete the appropriate checklist(s).

CP.VI.A.S2 Clear the area.

CP.VI.A.S3 Maintain heading throughout the maneuver, ±5°.

CP.VI.A.S4 Perform a maximum performance deceleration as directed by the evaluator.

CP.VI.A.S5 Select an appropriate power setting and thrust vector to allow deceleration at maximum rate.

CP.VI.A.S6 Maintain coordinated flight throughout the maneuver.

Task B. Inflight Conversion During Straight-and-Level Flight

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with

Area of Operation VI. Performance Maneuvers › Task C. Steep Turns

Area of Operation VI. Performance Maneuvers

converting from thrust-borne configuration to wing-borne configuration, and returning to thrust-borne configuration.

Knowledge: The applicant demonstrates understanding of:

CP.VI.B.K1 Procedures for changing aircraft configuration.

CP.VI.B.K2 Aerodynamic effects of changing aircraft configuration.

CP.VI.B.K3 Flight control operation when converting from thrust-borne to wing-borne configuration, and when converting from wing-borne to thrust-borne configuration, while in straight-and-level flight.

CP.VI.B.K4 Aircraft performance and limitation charts.

CP.VI.B.K5 Factors related to weight and balance and center of gravity (CG) envelopes.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VI.B.R1 Aircraft performance limitations.

CP.VI.B.R2 Powerplant failure during conversion.

CP.VI.B.R3 Aerodynamic stall.

CP.VI.B.R4 Effects of gross weight and CG.

CP.VI.B.R5 Rapid configuration or thrust vector changes.

CP.VI.B.R6 Other hazards specific to the powered-lift make and model.

CP.VI.B.R7 Altitude variation/vertical speed.

CP.VI.B.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.VI.B.S1 Convert from thrust-borne configuration to wing-borne configuration during straight-and-level flight.

CP.VI.B.S2 Convert the aircraft from wing-borne configuration to thrust-borne configuration during straight-andlevel flight.

CP.VI.B.S3 Utilize proper control technique throughout the maneuver.

CP.VI.B.S4 Maintain awareness of aircraft performance, limitations, and relative position throughout the maneuver.

CP.VI.B.S5 Maintain altitude ±100 feet and specified heading ±10° throughout the operation. Achieve and maintain targeted airspeed ±10 knots.

CP.VI.B.S6 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

CP.VI.B.S7 Use the appropriate checklist, if applicable.

Task C. Steep Turns

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with steep turns.

Knowledge: The applicant demonstrates understanding of:

Area of Operation VI. Performance Maneuvers

CP.VI.C.K1 Aerodynamics associated with steep turns, including:

CP.VI.C.K1a a. Maintaining coordinated flight

CP.VI.C.K1b b. Overbanking tendencies

CP.VI.C.K1c c. Maneuvering speed, including the impact of weight changes

CP.VI.C.K1d d. Load factor and accelerated stalls

CP.VI.C.K1e e. Rate and radius of turn

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VI.C.R1 Dividing attention between aircraft control and orientation.

CP.VI.C.R2 Collision hazards.

CP.VI.C.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

CP.VI.C.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.VI.C.R5 Uncoordinated flight.

Skills: The applicant exhibits the skill to:

CP.VI.C.S1 Clear the area.

CP.VI.C.S2 Establish the manufacturer's recommended airspeed; or if one is not available, an airspeed not to exceed maneuvering speed (VA).

CP.VI.C.S3 Roll into a coordinated 360° steep turn as selected by the evaluator and according to the aircraft's operating limitations.

CP.VI.C.S4 Perform the maneuver in the opposite direction.

CP.VI.C.S5 Maintain the entry altitude ±100 feet, airspeed ±10 knots, bank ±5°, and roll out on the entry heading ±10°.

Area of Operation VII. Navigation › Task A. Pilotage and Dead Reckoning

Area of Operation VII. Navigation

Area of Operation VII. Navigation

Task A. Pilotage and Dead Reckoning

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with pilotage and dead reckoning.

Knowledge: The applicant demonstrates understanding of:

CP.VII.A.K1 Pilotage and dead reckoning.

CP.VII.A.K2 Magnetic compass errors.

CP.VII.A.K3 Topography.

CP.VII.A.K4 Selection of appropriate:

CP.VII.A.K4a a. Route

CP.VII.A.K4b b. Altitude(s)

CP.VII.A.K4c c. Checkpoints

CP.VII.A.K5 Plotting a course, including:

CP.VII.A.K5a a. Determining heading, speed, and course

CP.VII.A.K5b b. Wind correction angle

CP.VII.A.K5c c. Estimating time, speed, and distance

CP.VII.A.K5d d. True airspeed and density altitude

CP.VII.A.K6 Aircraft configuration.

CP.VII.A.K7 Planned calculations versus actual results and required corrections.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VII.A.R1 Collision hazards.

CP.VII.A.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.VII.A.R3 Unplanned fuel/power consumption, if applicable.

Skills: The applicant exhibits the skill to:

CP.VII.A.S1 Prepare and use a flight log.

CP.VII.A.S2 Navigate by pilotage.

CP.VII.A.S3 Navigate by means of pre-computed headings, groundspeeds, elapsed time, and reference to landmarks or checkpoints.

CP.VII.A.S4 Use the magnetic direction indicator in navigation, including turns to headings.

CP.VII.A.S5 Correct for and record the differences between preflight fuel, groundspeed, and heading calculations and those determined en route.

Area of Operation VII. Navigation › Task B. Navigation Systems and Radar Services

Area of Operation VII. Navigation

CP.VII.A.S6 Verify position within two nautical miles of the flight-planned route.

CP.VII.A.S7 Arrive at the en route checkpoints within three minutes of the initial or revised estimated time of arrival (ETA) and provide a destination estimate.

CP.VII.A.S8 Maintain the selected altitude, ±100 feet and heading, ±10°.

Task B. Navigation Systems and Radar Services

eferences: R AC 91-78; AIM; FAA-H-8083-2, FAA-H-8083-25

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with navigation systems and radar services.

ote: N The evaluator should reference the manufacturer’s equipment supplement(s) as necessary for appropriate limitations, procedures, etc.

Knowledge: The applicant demonstrates understanding of:

CP.VII.B.K1 Ground-based navigation (identification, orientation, course determination, equipment, tests, regulations, interference, appropriate use of navigation data, and signal integrity).

CP.VII.B.K2 Satellite-based navigation (e.g., equipment, regulations, authorized use of databases, and Receiver Autonomous Integrity Monitoring (RAIM)).

CP.VII.B.K3 Radar assistance to visual flight rules (VFR) aircraft (e.g., operations, equipment, available services, traffic advisories).

CP.VII.B.K4 Transponder (Mode(s) A, C, and S) and Automatic Dependent Surveillance-Broadcast (ADS-B).

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VII.B.R1 Management of automated navigation and autoflight systems.

CP.VII.B.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.VII.B.R3 Limitations of the navigation system in use.

CP.VII.B.R4 Loss of a navigation signal.

CP.VII.B.R5 Use of an electronic flight bag (EFB), if used.

Skills: The applicant exhibits the skill to:

CP.VII.B.S1 Use an airborne electronic navigation system.

CP.VII.B.S2 Determine the aircraft's position using the navigation system.

CP.VII.B.S3 Intercept and track a given course, radial, or bearing.

CP.VII.B.S4 Recognize and describe the indication of station or waypoint passage.

CP.VIII.B.S5 Recognize signal loss or interference and take appropriate action, if applicable.

CP.VII.B.S6 Use proper communication procedures when utilizing radar services.

CP.VII.B.S7 Maintain the appropriate altitude, ±100 feet and heading, ±10°.

Area of Operation VII. Navigation › Task D. Lost Procedures

Area of Operation VII. Navigation

Task C. Diversion

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with diversion.

Knowledge: The applicant demonstrates understanding of:

CP.VII.C.K1 Selecting an alternate destination.

CP.VII.C.K2 Situations that require deviations from flight plan or air traffic control (ATC) instructions.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VII.C.R1 Collision hazards.

CP.VII.C.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.VII.C.R3 Circumstances that would make diversion prudent.

CP.VII.C.R4 Selecting an airport/heliport/helipad, as applicable.

CP.VII.C.R5 Using available resources (e.g., automation, ATC, and flight deck planning aids).

Skills: The applicant exhibits the skill to:

CP.VII.C.S1 Select a suitable airport/heliport/helipad, as applicable, and route for diversion.

CP.VII.C.S2 Make a reasonable estimate of heading, groundspeed, arrival time, and fuel required to the “divert to” destination.

CP.VII.C.S3 Promptly divert toward the airport/heliport/helipad.

CP.VII.C.S4 Maintain the selected altitude, ±100 feet and heading, ±10°.

CP.VII.C.S5 Update/interpret weather in flight.

CP.VII.C.S6 Use displays of digital weather and aeronautical information, as applicable to maintain situational awareness.

Task D. Lost Procedures

eferences: R AIM; FAA-H-8083-2, FAA-H-8083-25; VFR Navigation Charts

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with lost procedures and can take appropriate steps to achieve a satisfactory outcome if lost.

Knowledge: The applicant demonstrates understanding of:

CP.VII.D.K1 Methods to determine position.

CP.VII.D.K2 Assistance available if lost (e.g., radar services, communication procedures).

CP.VII.D.K3 Rapidly deteriorating weather or impending fuel exhaustion.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

Area of Operation VII. Navigation

CP.VII.D.R1 Collision hazards.

CP.VII.D.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.VII.D.R3 Recording times over waypoints.

CP.VII.D.R4 When to seek assistance or declare an emergency in a deteriorating situation.

Skills: The applicant exhibits the skill to:

CP.VII.D.S1 Select an appropriate course of action.

CP.VII.D.S2 Use an appropriate method to determine position.

CP.VII.D.S3 Maintain an appropriate heading and climb as necessary.

CP.VII.D.S4 Identify prominent landmarks.

CP.VII.D.S5 Use navigation systems/facilities or contact an ATC facility for assistance.

Area of Operation VIII. Slow Flight and Stalls › Task B. Power-Off Stalls

Area of Operation VIII. Slow Flight and Stalls

Area of Operation VIII. Slow Flight and Stalls

Task A. Maneuvering During Slow Flight (Wing-Borne Configuration)

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with maneuvering during slow flight in wing-borne configuration.

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

CP.VIII.A.K1 Aerodynamics associated with slow flight in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VIII.A.R1 Inadvertent slow flight and flight with a stall warning, which could lead to loss of control.

CP.VIII.A.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.A.R3 Uncoordinated flight.

CP.VIII.A.R4 Effect of environmental elements on aircraft performance (e.g., turbulence, microbursts, and high density altitude).

CP.VIII.A.R5 Collision hazards.

CP.VIII.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.VIII.A.S1 Clear the area.

CP.VIII.A.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet above ground level (AGL).

CP.VIII.A.S3 Establish and maintain an airspeed at which any further increase in angle of attack, increase in load factor, or reduction in power, would result in a stall warning (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.A.S4 Accomplish coordinated straight-and-level flight, turns, climbs, and descents with the aircraft configured as specified by the evaluator without a stall warning (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.A.S5 Maintain the specified altitude, ±50 feet; specified heading, ±10°; airspeed, +5/-0 knots; and specified angle of bank, ±5°.

Task B. Power-Off Stalls

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-off stalls.

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Area of Operation VIII. Slow Flight and Stalls

Knowledge: The applicant demonstrates understanding of:

CP.VIII.B.K1 Aerodynamics associated with stalls in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.

CP.VIII.B.K2 Stall characteristics as they relate to aircraft design, and recognition impending stall and full stall indications using sight, sound, or feel.

CP.VIII.B.K3 Factors and situations that can lead to a power-off stall and actions that can be taken to prevent it.

CP.VIII.B.K4 Fundamentals of stall recovery.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VIII.B.R1 Factors and situations that could lead to an inadvertent power-off stall, spin, and loss of control.

CP.VIII.B.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.B.R3 Stall warning(s) during normal operations.

CP.VIII.B.R4 Stall recovery procedure.

CP.VIII.B.R5 Secondary and accelerated stalls.

CP.VIII.B.R6 Effect of environmental elements on aircraft performance related to power-off stalls (e.g., turbulence, microbursts, and high-density altitude).

CP.VIII.B.R7 Collision hazards.

CP.VIII.B.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.VIII.B.S1 Clear the area.

CP.VIII.B.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet AGL or as recommended by the manufacturer, whichever is higher.

CP.VIII.B.S3 Configure the aircraft in the approach or landing configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver.

CP.VIII.B.S4 Establish a stabilized descent.

CP.VIII.B.S5 Transition smoothly from the approach or landing attitude to a pitch attitude that induces a stall.

CP.VIII.B.S6 Maintain a specified heading, ±10° if in straight flight; maintain a specified angle of bank not to exceed 20°, ±5°, if in turning flight, until an impending or full stall occurs, as specified by the evaluator.

CP.VIII.B.S7 Acknowledge the cues at the first indication of a stall (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.B.S8 Recover at the first indication of a stall or after a full stall has occurred, as specified by the evaluator.

CP.VIII.B.S9 Configure the aircraft as recommended by the manufacturer and accelerate to VX or VY.

CP.VIII.B.S10 Return to the altitude, heading, and airspeed specified by the evaluator.

CP.VIII.B.S11 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation VIII. Slow Flight and Stalls

Task C. Power-On Stalls

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

Area of Operation VIII. Slow Flight and Stalls › Task C. Power-On Stalls

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-on stalls.

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

CP.VIII.C.K1 Aerodynamics associated with stalls in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.

CP.VIII.C.K2 Stall characteristics as they relate to aircraft design, and recognition impending stall and full stall indications using sight, sound, or feel.

CP.VIII.C.K3 Factors and situations that can lead to a power-on stall and actions that can be taken to prevent it.

CP.VIII.C.K4 Fundamentals of stall recovery.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VIII.C.R1 Factors and situations that could lead to an inadvertent power-on stall, spin, and loss of control.

CP.VIII.C.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.C.R3 Pitch attitude limitations.

CP.VIII.C.R4 Stall warning(s) during normal operations.

CP.VIII.C.R5 Stall recovery procedure.

CP.VIII.C.R6 Secondary stalls and accelerated stalls.

CP.VIII.C.R7 Effect of environmental elements on aircraft performance related to power-on stalls (e.g., turbulence, microbursts, and high-density altitude).

CP.VIII.C.R8 Collision hazards.

CP.VIII.C.R9 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.VIII.C.S1 Clear the area.

CP.VIII.C.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet AGL or as recommended by the manufacturer, whichever is higher.

CP.VIII.C.S3 Establish the takeoff, departure, or wing-borne configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver.

CP.VIII.C.S4 Transition smoothly from the takeoff or departure attitude to the pitch attitude that would induce a stall.

CP.VIII.C.S5 Maintain a specified heading ±10° if in straight flight; maintain a specified angle of bank not to exceed 20°, ±10° if in turning flight, until an impending or full stall is reached, as specified by the evaluator.

CP.VIII.C.S6 Acknowledge the cues at the first indication of a stall (e.g., aircraft buffet, stall horn, etc.).

Area of Operation VIII. Slow Flight and Stalls › Task D. Accelerated Stalls

Area of Operation VIII. Slow Flight and Stalls

CP.VIII.C.S7 Recover at the first indication of a stall or after a full stall has occurred, as specified by the evaluator.

CP.VIII.C.S8 Configure the aircraft as recommended by the manufacturer and accelerate to VX or VY.

CP.VIII.C.S9 Return to the altitude, heading, and airspeed specified by the evaluator.

CP.VIII.C.S10 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task D. Accelerated Stalls

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with accelerated stalls (power-on or power-off).

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

CP.VIII.D.K1 Aerodynamics associated with stalls in various aircraft configurations, including the relationship between angle of attack, airspeed, load factor, power setting, aircraft weight and center of gravity, aircraft attitude, and yaw effects.

CP.VIII.D.K2 Stall characteristics as they relate to aircraft design, and recognition impending stall and full stall indications using sight, sound, or feel.

CP.VIII.D.K3 Factors leading to an accelerated stall and preventive actions.

CP.VIII.D.K4 Fundamentals of stall recovery.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.VIII.D.R1 Factors and situations that could lead to an inadvertent accelerated stall, spin, and loss of control.

CP.VIII.D.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.D.R3 Stall warning(s) during normal operations.

CP.VIII.D.R4 Stall recovery procedure.

CP.VIII.D.R5 Secondary stalls and accelerated stalls.

CP.VIII.D.R6 Effect of environmental elements on aircraft performance related to power-on stalls (e.g., turbulence, microbursts, and high-density altitude).

CP.VIII.D.R7 Collision hazards.

CP.VIII.D.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.VIII.D.S1 Clear the area.

CP.VIII.D.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet AGL or as recommended by the manufacturer, whichever is higher.

CP.VIII.D.S3 Establish the takeoff, departure, or wing-borne configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver.

Area of Operation VIII. Slow Flight and Stalls

CP.VIII.D.S4 Set power as assigned by the evaluator.

CP.VIII.D.S5 Establish and maintain a coordinated turn in a 45° bank (or as limited by the manufacturer), increasing elevator back pressure smoothly and firmly until an impending stall is reached.

CP.VIII.D.S6 Acknowledge the cues at the first indication of a stall (e.g., aircraft buffet, stall horn, etc.).

CP.VIII.D.S7 Recover at the first indication of a stall.

CP.VIII.D.S8 Configure the aircraft as recommended by the manufacturer and accelerate to VX or VY.

CP.VIII.D.S9 Return to the altitude, heading, and airspeed specified by the evaluator.

CP.VIII.D.S10 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation IX. Emergency Operations › Task A.

Area of Operation IX. Emergency Operations

Area of Operation IX. Emergency Operations

Task A. Powerplant(s) Failure (Simulated) during Takeoff in Thrust-Borne Flight

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with indications and pilot actions after powerplant(s) failure during takeoff while the aircraft is predominantly in thrust-borne flight in a multi-powerplant aircraft.

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

ote: N The task outcome can be vertical or rolling depending on aircraft capabilities, configuration, and flight manual procedures.

Knowledge: The applicant demonstrates understanding of:

CP.IX.A.K1 Aircraft performance and limitations, (e.g., height velocity (H/V) diagram information).

CP.IX.A.K2 Factors involved in determining a valid go/no-go decision.

CP.IX.A.K3 Recognition of powerplant(s) failure.

CP.IX.A.K4 Pilot actions required on recognition of powerplant(s) failure, including checklist memory items.

CP.IX.A.K5 Aircraft configuration for landing with powerplant(s) failure.

CP.IX.A.K6 Causes of asymmetric thrust conditions and appropriate responses.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.A.R1 Powerplant(s) failure.

CP.IX.A.R2 Identification of powerplant(s) failure conditions.

CP.IX.A.R3 Pilot reaction to powerplant(s) failure conditions.

CP.IX.A.R4 Aircraft configuration.

Skills: The applicant exhibits the skill to:

CP.IX.A.S1 Recognize that a powerplant(s) failure has occurred.

CP.IX.A.S2 Use flight controls in the proper combination and aircraft configuration as recommended by the manufacturer, or as required to maintain best performance, and trim as required.

CP.IX.A.S3 Maintain the operating powerplant(s) within acceptable operating limits.

CP.IX.A.S4 Land the aircraft, as appropriate to the scenario presented by the evaluator.

CP.IX.A.S5 Complete the appropriate checklist(s).

CP.IX.A.S6 Make radio calls as appropriate.

CP.IX.A.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation IX. Emergency Operations

Task B. Powerplant(s) Failure (Simulated) during Takeoff While in Semi-Wing-Borne Flight

Area of Operation IX. Emergency Operations › Task B.

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with indications and pilot actions after powerplant(s) failure during takeoff while in semi-wing-borne flight in a multi-powerplant aircraft.

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

ote: N This can be initiated during the takeoff roll in wheeled aircraft or during the transition to wing-borne flight following a vertical takeoff.

Knowledge: The applicant demonstrates understanding of:

CP.IX.B.K1 The procedures used during a powerplant(s) failure on takeoff, the appropriate reference airspeeds, and the specific pilot actions required.

CP.IX.B.K2 Operational considerations to include: aircraft performance (e.g., sideslip, bank angle, etc.), takeoff warning systems, runway length, surface conditions, density altitude, wake turbulence, environmental conditions, obstructions, and other related factors that could adversely affect safety.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.B.R1 Powerplant(s) failure.

CP.IX.B.R2 Reaction to the loss of power from one or more powerplants.

CP.IX.B.R3 Deceleration in a space-limited environment.

CP.IX.B.R4 Windshear.

CP.IX.B.R5 Dividing attention inside and outside the aircraft.

CP.IX.B.R6 Runway incursion.

CP.IX.B.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.IX.B.R8 Abnormal operations, including planning for.

CP.IX.B.R8a a. Rejected takeoff

CP.IX.B.R8b b. Powerplant failure in takeoff/climb phase of flight

CP.IX.B.R9 Energy management.

Skills: The applicant exhibits the skill to:

CP.IX.B.S1 Recognize that a powerplant failure has occurred while performing a rolling takeoff.

CP.IX.B.S2 Input the appropriate flight control(s) and configure the aircraft for maximum deceleration.

CP.IX.B.S3 Maintain the operating powerplant(s) within acceptable operating limits.

CP.IX.B.S4 Apply braking as appropriate.

CP.IX.B.S5 Refer to the checklist to ensure that the emergency procedure was followed correctly.

CP.IX.B.S6 Make radio calls as appropriate.

Area of Operation IX. Emergency Operations › Task C.

Area of Operation IX. Emergency Operations

CP.IX.B.S7 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task C. Inflight Powerplant(s) Failure and Restart in Multi-Powerplant Aircraft

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with an inflight powerplant(s) failure and restart, if applicable, in a multi-powerplant powered-lift aircraft.

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

CP.IX.C.K1 Flight characteristics and controllability associated with maneuvering the aircraft with powerplant(s) inoperative, including the importance of drag reduction and appropriate aircraft configuration.

CP.IX.C.K2 Aircraft/powerplant limitations.

CP.IX.C.K3 Powerplant restart procedures and conditions where a restart attempt is appropriate.

CP.IX.C.K4 Causes of asymmetric thrust conditions and appropriate responses.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.C.R1 Potential powerplant(s) failure during flight.

CP.IX.C.R2 Following checklist procedures for a powerplant(s) failure or a powerplant(s) restart.

CP.IX.C.R3 Identifying the powerplant(s) that failed.

CP.IX.C.R4 Collision hazards.

CP.IX.C.R5 Aircraft configuration.

CP.IX.C.R6 Factors and situations that could lead to loss of control with an inflight powerplant(s) failure.

CP.IX.C.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.IX.C.S1 Recognize and correctly identify powerplant(s) failure, complete memory items (if applicable), and maintain positive aircraft control.

CP.IX.C.S2 Coordinate with crew, if applicable, and complete the appropriate emergency procedures and checklist(s) for powerplant shutdown.

CP.IX.C.S3 Use flight controls and configure the aircraft in the proper combination as recommended by the manufacturer, or as required, to maintain best performance, and trim as required.

CP.IX.C.S4 Determine the cause for the powerplant(s) failure and if a restart is a viable option.

CP.IX.C.S5 Maintain the operating powerplant(s) within acceptable operating limits.

CP.IX.C.S6 Maintain the airspeed ±10 knots, the specified heading ±10°, and altitude ±100 feet as specified by the evaluator and within the aircraft’s capability.

CP.IX.C.S7 Consider a powerplant restart and, if appropriate, demonstrate the powerplant restart procedures in accordance with the manufacturer or operator specified procedures and checklists.

Area of Operation IX. Emergency Operations › Task E. Approach and Landing with Powerplant(s) Failure (Simulated)

Area of Operation IX. Emergency Operations

CP.IX.C.S8 Select the nearest suitable airport or landing area.

CP.IX.C.S9 Communicate with air traffic control (ATC) and the evaluator, as appropriate for the situation.

CP.IX.C.S10 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task D. Vortex Ring State (VRS) Avoidance

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge and risk management associated with preventing the aircraft from entering and the procedure for recovering from Vortex Ring State (VRS).

ote: N Evaluator assesses this Task orally only.

Knowledge: The applicant demonstrates understanding of:

CP.IX.D.K1 Elements of vortex ring state.

CP.IX.D.K2 Effects of wind, weight, temperature, and density altitude.

CP.IX.D.K3 Requirements for the formation of VRS.

CP.IX.D.K4 Aircraft systems that aid the pilot in avoiding VRS, if applicable.

CP.IX.D.K5 Aerodynamics and indications of VRS.

CP.IX.D.K6 Flight scenarios under which VRS can occur.

CP.IX.D.K7 Asymmetric VRS, if applicable.

CP.IX.D.K8 Effective recovery techniques.

CP.IX.D.K9 Control inputs and configuration changes to recover from VRS.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.D.R1 Conditions for entering VRS.

CP.IX.D.R2 Pilot recognition and response to VRS.

CP.IX.D.R3 Loss of control.

CP.IX.D.R4 Collision hazards.

CP.IX.D.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.IX.D.S1 [Intentionally left blank].

Task E. Approach and Landing with Powerplant(s) Failure (Simulated)

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with approach and landing with simulated powerplant(s) failure.

ote: N See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements &

Area of Operation IX. Emergency Operations › Task F. Emergency Descent

Area of Operation IX. Emergency Operations

Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

CP.IX.E.K1 Elements of approach and landing with powerplant(s) failure.

CP.IX.E.K2 Effects of atmospheric conditions on emergency approach and landing.

CP.IX.E.K3 A stabilized approach, including energy management concepts.

CP.IX.E.K4 Air traffic control (ATC) services to aircraft in distress.

CP.IX.E.K5 Appropriate approach and landing profiles and aircraft configurations.

CP.IX.E.K6 Causes of asymmetric thrust conditions and appropriate responses.

CP.IX.E.K7 Go-around/rejected landing procedures with a powerplant failure.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.E.R1 Consideration of altitude, wind, terrain, obstructions, and available landing area.

CP.IX.E.R2 Planning and following a flightpath to the selected landing area.

CP.IX.E.R3 Collision hazards.

CP.IX.E.R4 Flight control input(s).

CP.IX.E.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).

CP.IX.E.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.IX.E.R7 Go-around/rejected landing.

Skills: The applicant exhibits the skill to:

CP.IX.E.S1 Maintain the operating powerplant(s) within limits.

CP.IX.E.S2 Maintain, prior to beginning the final approach segment, the recommended flight profile with altitude ±100 feet, airspeed, ±10 knots, heading ±5°, and maintains track.

CP.IX.E.S3 Use flight controls in the proper combination and aircraft configuration as recommended by the manufacturer, or as required to maintain best performance, and trim as required.

CP.IX.E.S4 Select a suitable landing area considering altitude, wind, terrain and obstructions.

CP.IX.E.S5 Plan and follow a flightpath to the selected landing area considering altitude, wind, terrain, and obstructions.

CP.IX.E.S6 Maintain directional control and appropriate crosswind correction throughout the approach and landing.

CP.IX.E.S7 Complete the appropriate checklist(s).

CP.IX.E.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task F. Emergency Descent

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with

Area of Operation IX. Emergency Operations › Task G. Emergency Equipment and Survival Gear

Area of Operation IX. Emergency Operations

emergency descent.

ote: N See Appendix 2: Safety of Flight.

Knowledge: The applicant demonstrates understanding of:

CP.IX.F.K1 Situations that would require an emergency descent (e.g., depressurization, smoke, or fire).

CP.IX.F.K2 Immediate action items and emergency procedures.

CP.IX.F.K3 Airspeed, including airspeed limitations.

CP.IX.F.K4 Aircraft performance and limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.F.R1 Altitude, wind, terrain, obstructions, gliding distance, and available landing distance considerations.

CP.IX.F.R2 Collision hazards.

CP.IX.F.R3 Flight control input(s) and aircraft configuration.

CP.IX.F.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.

Skills: The applicant exhibits the skill to:

CP.IX.F.S1 Clear the area.

CP.IX.F.S2 Establish and maintain the appropriate airspeed and configuration appropriate to the scenario specified by the evaluator and as covered in the manufacturer's flight manual for the emergency descent.

CP.IX.F.S3 Maintain orientation, divide attention appropriately, and plan and execute a smooth recovery.

CP.IX.F.S4 Use bank angles between 30° and 45° to maintain positive load factors during the descent.

CP.IX.F.S5 Maintain appropriate airspeed, +0/-10 knots, and level off at specified altitude, ±100 feet.

CP.IX.F.S6 Make radio calls as appropriate.

CP.IX.F.S7 Complete the appropriate checklist(s).

CP.IX.F.S8 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Task G. Emergency Equipment and Survival Gear

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with emergency equipment, and survival gear appropriate to the aircraft and environment encountered during flight.

Knowledge: The applicant demonstrates understanding of:

CP.IX.G.K1 Emergency Locator Transmitter (ELT) operations, limitations, and testing requirements.

CP.IX.G.K2 Fire extinguisher operations and limitations.

CP.IX.G.K3 Emergency equipment and survival gear needed for:

Area of Operation IX. Emergency Operations

Area of Operation IX. Emergency Operations › Task H. Systems and Equipment Malfunctions

CP.IX.G.K3a a. Climate extremes (hot/cold)

CP.IX.G.K3b b. Mountainous terrain

CP.IX.G.K3c c. Overwater operations

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.G.R1 Survival gear (water, clothing, shelter) for 48 to 72 hours.

Skills: The applicant exhibits the skill to:

CP.IX.G.S1 Identify appropriate equipment and personal gear.

CP.IX.G.S2 Brief passengers on proper use of on-board emergency equipment and survival gear.

Task H. Systems and Equipment Malfunctions

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with system and equipment malfunctions appropriate to the aircraft provided for the practical test.

Knowledge: The applicant demonstrates understanding of:

CP.IX.H.K1 Causes of partial or complete power loss related to the specific type of powerplant(s).

CP.IX.H.K2 System and equipment malfunctions specific to the aircraft, including:

CP.IX.H.K2a a. Electrical malfunction

CP.IX.H.K2b b. Vacuum/pressure and associated flight instrument malfunctions

CP.IX.H.K2c c. Pitot-static system malfunction

CP.IX.H.K2d d. Electronic flight deck display malfunction

CP.IX.H.K2e e. Landing gear or flap malfunction

CP.IX.H.K2f f. Inoperative trim

CP.IX.H.K3 Smoke/fire/powerplant compartment fire.

CP.IX.H.K4 Any other system specific to the aircraft (e.g., supplemental oxygen, deicing).

CP.IX.H.K5 Inadvertent door or window opening.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.H.R1 Startle response.

CP.IX.H.R2 Checklist usage for a system or equipment malfunction.

CP.IX.H.R3 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.IX.H.R4 Undesired aircraft state.

Skills: The applicant exhibits the skill to:

Area of Operation IX. Emergency Operations › Task J. Recovery from Unusual Flight Attitudes

Area of Operation IX. Emergency Operations

CP.IX.H.S1 Determine appropriate action for simulated emergencies specified by the evaluator, from at least three of the elements or sub-elements listed in K1 through K5.

CP.IX.H.S2 Complete the appropriate checklist(s).

Task I. Dynamic Rollover

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with dynamic rollover.

ote: N Evaluator assesses this Task orally only.

Knowledge: The applicant demonstrates understanding of:

CP.IX.I.K1 Elements related to dynamic rollover.

CP.IX.I.K2 Interactions between thrust, crosswind, slope, lateral CG, aircraft weight, and flight controls that contribute to dynamic rollover.

CP.IX.I.K3 Preventive flight technique and recovery during flight operations, including slope operations.

CP.IX.I.K4 Aircraft slope limitations.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.I.R1 Surface conditions conducive to dynamic rollover.

CP.IX.I.R2 Landing gear proximity to the surface.

CP.IX.I.R3 Flight control inputs during takeoff or landing.

CP.IX.I.R4 Sideward hover.

CP.IX.I.R5 Critical rollover angle and rolling moment.

CP.IX.I.R6 Translating tendency.

Skills: The applicant exhibits the skill to:

CP.IX.I.S1 [Intentionally left blank].

Task J. Recovery from Unusual Flight Attitudes

eferences: R FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with attitude instrument flying while recovering from unusual attitudes solely by reference to instruments.

ote: N See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.

Knowledge: The applicant demonstrates understanding of:

CP.IX.J.K1 Prevention of unusual attitudes, including flight causal, physiological, and environmental factors, and system and equipment failures.

Area of Operation IX. Emergency Operations

CP.IX.J.K2 Procedures for recovery from unusual attitudes in flight.

CP.IX.J.K3 Procedures available to safely regain visual meteorological conditions (VMC) after flight into inadvertent instrument meteorological conditions or unintended instrument meteorological conditions (IIMC)/(UIMC).

CP.IX.J.K4 Appropriate use of automation, if applicable.

Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:

CP.IX.J.R1 Situations that could lead to loss of control in-flight (LOC-I) or unusual attitudes in-flight (e.g., stress, task saturation, inadequate instrument scan distractions, and spatial disorientation).

CP.IX.J.R2 Assessment of the unusual attitude.

CP.IX.J.R3 Control input errors, inducing undesired aircraft attitudes.

CP.IX.J.R4 Collision hazards.

CP.IX.J.R5 Distractions, task prioritization, loss of situational awareness, or disorientation.

CP.IX.J.R6 Interpreting flight instruments.

CP.IX.J.R7 Operating envelope considerations.

Skills: The applicant exhibits the skill to:

CP.IX.J.S1 Use proper instrument cross-check and interpretation to identify an unusual attitude (including both nose-high and nose-low) in flight, and apply the appropriate flight control, power input, and aircraft configuration in the correct sequence, to return to a stabilized level flight attitude.

CP.IX.J.S2 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.

Area of Operation X. High-Altitude Operations › Task B. Pressurization

Area of Operation X. High-Altitude Operations

Area of Operation X. High-Altitude Operations

Task A. Supplemental Oxygen

eferences: R 14 CFR part 91; AC 61-107; AIM; FAA-H-8083-2, FAA-H-8083-25; Flight Manual

bjective: O To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight at higher altitudes where supplemental oxygen is required or recommended.

Knowledge: The applicant demonstrates understanding of:

CP.X.A.K1 Regulatory requirements for supplemental oxygen use by flight crew and passengers.

CP.X.A.K2 Physiological factors, including:

CP.X.A.K2a a. Impairment

CP.X.A.K2b b. Symptoms of hypoxia

CP.X.A.K2c c. Time of useful consciousness (TUC)

CP.X.A.K3 Operational factors, including:

CP.X.A.K3a a. Characteristics, limitations, and applicability of continuous flow, demand, and pressure-

demand oxygen systems

CP.X.A.K3b b. Differences between and identification of “aviator’s breathing oxygen” and other types of

oxygen

CP.X.A.K3c c. Precautions when using supplemental oxygen systems

Continue reading ↓ 120 of 171 passages shown