AC 150/5340-30D Design And Installation Details For Airport Visual Aids
Provides guidance and recommendations on the installation of airport visual aids. Because of the size of the document, it is available as one large file (see Complete) or as five smaller files (see Parts 1-6). See also-- Airport Technical Advisory on Electromagnetic Interference (EMI) (below) The Design, Installation, and Maintenance of In-Pavement Airport Lighting (PDF) by Arthur S. Schai
This document is cancelled. It may have been replaced. Check the official source before relying on it.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: DESIGN AND INSTALLATION
DETAILS FOR AIRPORT VISUAL AIDS
Date: 9/30/08 Initiated by: AAS-100
AC No.: 150/5340-30D Change:
1. PURPOSE. This advisory circular (AC) provides guidance and recommendations on the installation of airport visual aids.
DETAILS FOR AIRPORT VISUAL AIDS
2. CANCELLATION. AC 150/5340-30C, Design and Installation Details for Airport Visual Aids, dated September 20, 2007, is cancelled.
3. APPLICATION. The Federal Aviation Administration (FAA) recommends the guidance and specifications in this Advisory Circular for Airport Visual Aids. In general, use of this AC is not mandatory. However, use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and with revenue from the Passenger Facility Charges (PFC) Program. See Grant Assistance No. 34, “Policies, Standards, and Specifications,” and PFC Assurance No.9, “Standards and Specifications.” All lighting configurations contained in this standard are the only means acceptable to the Administrator to meet the lighting requirements of Title 14 CFR Part 139, Certification and Operations: Land Airports Serving Certain Air Carriers, Section 139.311, Marking, Signs and Lighting. See exception in paragraph 2.1.2b (2), Location and Spacing.
4. PRINCIPAL CHANGES. The following changes have been incorporated:
a. Appendix 7, Runway Status Lights (RWSL) is added.
b. Paragraph 2.1.3, Stopway Edge Lights, is added.
c. Paragraph 6, Beacon Towers, is updated to include newer tower and pole designs.
d. Paragraph 6.3, Wind Cones, is updated to include new information about the location of supplemental wind cones.
5. METRICS. To promote an orderly transition to metric units, this AC contains both English and metric dimensions. The metric conversions may not be exact metric equivalents, and, until there is an official changeover to the metric system, the English dimensions will govern.
6. COMMENTS OR SUGGESTIONS for improvements to this AC should be sent to:
Manager, Airport Engineering Division Federal Aviation Administration ATTN: AAS-100 800 Independence Avenue, S.W. Washington, DC 20591
AC 150/5340-30D 9/30/2008
ii
7. COPIES OF THIS AC. The Office of Airport Safety and Standards is in the process of making ACs available to the public through the Internet. These ACs may be found through the FAA home page (www.faa.gov). A printed copy of this and other ACs can be ordered from the U.S. Department of Transportation, Subsequent Business Office, Ardmore East Business Center, 3341 Q 75th Avenue, Landover, Maryland, 20785.
Michael J. O’Donnell Director of Airport Safety and Standards
iii
TABLE OF CONTENTS
TABLE OF CONTENTS
CHAPTER 1. INTRODUCTION … 1
1.1. GENERAL … 1
1.2. SCOPE … 1
1.3. SAFETY … 1
CHAPTER 2. RUNWAY AND TAXIWAY EDGE LIGHTING SYSTEMS … 3
2.1. GENERAL … 3 2.1.1. Selection Criteria … 3 2.1.2. Runway Edge Light Configurations … 3 2.1.3. Stopway Edge Lights … 6 2.1.4. Taxiway Edge Light Configurations … 7 2.1.5. System Design … 8 2.1.6. Equipment and Materials … 11
CHAPTER 3. RUNWAY CENTERLINE AND TOUCHDOWN LIGHTING SYSTEMS.... 13
CHAPTER 3. RUNWAY CENTERLINE AND TOUCHDOWN LIGHTING SYSTEMS.... 13
3.1. INTRODUCTION … 13
3.2. SELECTION CRITERIA … 13
3.3. CONFIGURATION … 13
3.4. DESIGN … 14
3.5. EQUIPMENT AND MATERIAL … 15
CHAPTER 4. TAXIWAY LIGHTING SYSTEMS … 17
4.1. INTRODUCTION … 17
4.2. IMPLEMENTATION CRITERIA … 17
4.3. TAXIWAY CENTERLINE … 18
4.3. TAXIWAY CENTERLINE … 18
4.4. RUNWAY GUARD LIGHTS (RGLs) … 21
4.5. RUNWAY STOP BAR … 22
4.6. COMBINATION IN-PAVEMENT STOP BAR AND RGLS … 24
4.7. CLEARANCE BAR CONFIGURATION … 24
4.8. DESIGN … 25
4.9. EQUIPMENT AND MATERIAL … 33
4.10. INSTALLATION … 34
CHAPTER 5. LAND AND HOLD SHORT LIGHTING SYSTEMS … 35
5.1. INTRODUCTION … 35
5.1. INTRODUCTION … 35
5.2. BACKGROUND … 35
5.3. DEFINITIONS … 35
5.4. IMPLEMENTATION CRITERIA … 35
5.5. CONFIGURATION … 35
5.6. DESIGN … 36
5.7. EQUIPMENT AND MATERIAL … 38
AC 150/5340-30D 9/30/2008
iv
5.8. INSTALLATION … 38
CHAPTER 6. AIRFIELD MISCELLANEOUS AIDS … 41
6.1. AIRPORT ROTATING BEACONS … 41
6.2 BEACON TOWERS … 43
6.2 BEACON TOWERS … 43
6.3 WIND CONES … 44
6.4 OBSTRUCTION LIGHTS … 45 6.4.1. Location … 45 6.4.2. Installation … 46 6.4.3. Maintenance … 46
6.5 EQUIPMENT AND MATERIALS … 46
CHAPTER 7. ECONOMY APPROACH AIDS … 49
7.1. INTRODUCTION … 49
7.2. TYPES OF ECONOMY APPROACH LIGHTING AIDS … 49
7.3. SELECTION CONSIDERATIONS … 49
7.3. SELECTION CONSIDERATIONS … 49
7.4. CONFIGURATIONS … 50
7.5. DESIGN … 52
7.6. EQUIPMENT AND MATERIAL … 62
7.7. INSTALLATION … 63
CHAPTER 8. RADIO CONTROL EQUIPMENT … 67
8.1. RADIO CONTROL EQUIPMENT … 67 8.1.1 Restrictions on Use of Radio Control … 67 8.1.2 Radio Control Equipment … 67 8.1.3 Interfacing the Radio Control with the Lighting Systems … 68 8.1.4 Coordination With FAA … 70
CHAPTER 9. STANDBY POWER – NON-FAA … 73
CHAPTER 9. STANDBY POWER – NON-FAA … 73
9.1. BACKGROUND … 73
9.2. DEFINITIONS … 73
9.3. FAA POLICY … 73
9.4. ELECTRICAL POWER CONFIGURATIONS … 74
9.5. DESIGN … 75
9.6. EQUIPMENT AND MATERIAL … 76
9.7. INSTALLATION … 78
9.8. INSPECTION … 79
9.9. TESTS … 80
9.10. MAINTENANCE … 80
9.11. REDUCING ELECTRICAL POWER INTERRUPTIONS … 81
9.12. ENGINE GENERATOR EQUIPMENT PERFORMANCE REQUIREMENTS … 81
9.12. ENGINE GENERATOR EQUIPMENT PERFORMANCE REQUIREMENTS … 81
CHAPTER 10. PAVEMENT TYPES … 83
10.1. GENERAL … 83
v
10.2. NEW PAVEMENT – RIGID (CONCRETE) … 83
10.3. NEW PAVEMENT – FLEXIBLE (BITUMINOUS) … 85
10.4. OVERLAY – RIGID … 86
10.5. OVERLAY - FLEXIBLE … 87
CHAPTER 11. FIXTURE MOUNTING BASES … 89
11.1. GENERAL … 89
11.1. GENERAL … 89
11.2. L-868 MOUNTING BASES … 89
11.3. DIRECT-MOUNTED (INSET) FIXTURES … 91
11.4. FIELD ADJUSTABLE L-868 MOUNTING BASES … 93
11.5. INSTALLATION … 93
CHAPTER 12. EQUIPMENT AND MATERIAL … 97
12.1. GENERAL … 97
12.2. LIGHT BASES, TRANSFORMER HOUSINGS AND JUNCTION BOXES … 97
12.3. DUCT AND CONDUIT … 97
12.3. DUCT AND CONDUIT … 97
12.4. CABLE, CABLE CONNECTORS, PLUGS AND RECEPTACLES … 98
12.5. COUNTERPOISE (LIGHTNING PROTECTION SYSTEM) … 99
12.6. SAFETY (EQUIPMENT) GROUND … 100
12.7. CONCRETE … 100
12.8. STEEL REINFORCEMENT … 101
12.9. ADHESIVE AND SEALANTS … 101
12.10. LOAD-BEARING LIGHTING FIXTURES … 101
12.11. INSPECTION … 102
12.11. INSPECTION … 102
12.12. TESTING … 103
12.13. AUXILIARY RELAYS … 104
12.14. VAULT … 104
12.15. MAINTENANCE … 104
CHAPTER 13. POWER DISTRIBUTION AND CONTROL SYSTEMS … 105
13.1. INTRODUCTION … 105 13.1.1. NEC … 105
13.2. POWER DISTRIBUTION … 105
13.3. CONTROL SYSTEMS … 106 13.3.1. Airfield Lighting Control … 106 13.3.2. Computerized Control Systems … 106
APPENDIX 1. FIGURES … 111
APPENDIX 1. FIGURES … 111
APPENDIX 2. AIRPORT TECHNICAL ADVISORY … 225
APPENDIX 3. TERMS & ACRONYMS … 227
APPENDIX 4. BIBLIOGRAPHY … 233
AC 150/5340-30D 9/30/2008
vi
APPENDIX 5. TYPICAL INSTALLATION DRAWINGS FOR AIRPORT LIGHTING EQUIPMENT … 237
A5-1. Electrical Notes … 264
APPENDIX 6. APPLICATION NOTES … 273
APPENDIX 7. RUNWAY STATUS LIGHT SYSTEM (RWSL) … 285
APPENDIX 7. RUNWAY STATUS LIGHT SYSTEM (RWSL) … 285
A7-1. Purpose … 285
A7-1.1. System Description … 285
A7-2. Installation … 286 A7-2.1 REL … 286
A7-2.2 REL Light Base … 286
A7-2.3 REL Configurations … 286 A7-2.3.1 Basic (90-degree) Configuration … 286 A7-2.3.2 Angled Configuration … 287 A7-2.3.3 Curved Configuration … 288
A7-2.4 Takeoff Hold Lights (THL) … 288
A7-2.4.1 THL Fixtures … 288
A7-2.4.2 THL Mounting Base … 289
A7-2.5 CCR Power Supply … 289
A7-2.6 Isolation Transformer … 289
A7-2.7 Individual Light Controller (ILC) … 289
A7-3 DESIGN … 290
A7-3 DESIGN … 290
A7-3.1 General Guidelines … 290
A7-3.2 Layout … 290 A7-3.3 Overlay Rigid and Flexible Pavements … 290
A7-3.4 Existing Pavements … 290
A7-4 SMGCS … 290
A7-5 EQUIPMENT AND MATERIAL … 290
A7-5.1 Lighting Vault … 290
A7-6 Operational Testing … 290
LIST OF FIGURES
Figure 1. Legend and General Notes … 112 Figure 2. Runway and Threshold Lighting Configuration (LIRL & MIRL) … 113 Figure 3. Runway and Threshold Lighting Configuration (HIRL) … 114 Figure 4. Runway with Taxiway at End … 115 Figure 5. Runway with Blast Pad (No Traffic) … 116 Figure 6. Lighting for Runway with Displaced Threshold … 117 Figure 7. Normal Runway with Taxiway … 118 Figure 8. Lighting for Runway with Displaced Threshold … 119 Figure 9. Lighting for Runway with Displaced Threshold/Usable Pavement … 120 Figure 10. Lighting for Runway with Displaced Threshold not Coinciding with Opposite Runway End … 121 Figure 11. Lighting for Runway with Stopway … 122 Figure 12. Lighting for Runway with Displaced Threshold & Stopway … 123
Figure 1 · page 6Picture of the page from the copy saved here
LIST OF FIGURES
vii
Figure 13. Runway with End Taxiway … 124 Figure 14. Lighting for Runway with End Taxiway and Shortened ASDA … 125 Figure 15. Lighting for Runway with End Taxiway and Displaced Threshold not Coinciding with Opposite Runway End … 126 Figure 16. Typical Straight Taxiway Sections (Less Than 200 Feet (61 m)) … 127 Figure 17. Spacing of Lights on Curved Taxiway Edges … 128 Figure 18. Typical Single Straight Taxiway Edges (More Than 200 Feet (61 m)) … 129 Figure 19. Typical Single Straight Taxiway Edges (Less Than 200 Feet (61 m)) … 130 Figure 20. Typical Edge Lighting Configuration … 131 Figure 21. Typical Edge Lighting for Portions of Runways Used as Taxiway (When Taxiway Lights Are “On”). 132 Figure 22. Typical Edge Lighting for Portions of Runways Used as Taxiway (When Runway Lights Are “On”)..133 Figure 23. Light Fixture Wiring … 134 Figure 24. Typical Wiring Diagram Utilizing L-828 Step-type Regulator with External Remote Primary Oil Switch … 135 Figure 25. Typical Wiring Diagram Utilizing L-828 Step-type Regulator with Internal Control Power and Primary Oil Switch … 136 Figure 26.
Figure 13 · page 7Picture of the page from the copy saved here
Typical Basic 120 VAC Remote Control System … 137 Figure 27. Alternative 120 VAC Remote Control System … 138 Figure 28. Typical 120 VAC Remote Control System with L-847 Circuit Selector Switch … 139 Figure 29. Typical 48 VDC Remote Control System with 5-Step Regulator and L-841 Relay Panel … 140 Figure 30. Typical 48 VDC Remote Control System with 3-Step Regulator and L-841 Relay Panel … 141 Figure 31. Curves for Estimating Loads in High Intensity Series Circuits … 142 Figure 32. Curves for Estimating Loads in Medium Intensity Series Circuits … 143 Figure 33. Runway Centerline Lighting Layout … 144 Figure 34. Touchdown Zone Lighting Layout … 145 Figure 35. Section Through Non-adjustable Base and Anchor, Base and Conduit System, Rigid Pavement … 146 Figure 36. Section Through Non-adjustable Base and Anchor, Base and Conduit System, Flexible Pavement … 147 Figure 37. Runway Centerline Light – Shallow Base & Conduit Installation … 148 Figure 38. Saw Kerf Wireway Details … 149 Figure 39. Saw Kerf Orientation Details – R/W Centerline and TDZ Lights … 150 Figure 40.
Figure 27 · page 7Picture of the page from the copy saved here
Transformer Housing Installation Details Inset Type Lighting Fixtures … 151 Figure 41. Typical Equipment Layout, Inset Type Lighting Fixtures … 152 Figure 42. Junction Box for Inset Fixture Installation … 153 Figure 43. Typical Taxiway Centerline Lighting Configuration for Non-Standard Fillets (Centerline light spacing for operations above 1,200 feet (365 m) RVR) … 154 Figure 44. Color-Coding of Exit Taxiway Centerline Lights … 155 Figure 45. Taxiway Centerline Lighting Configuration for Acute-Angled Exits … 156 Figure 46. Controlled Stop Bar Design and Operation – “GO” Configuration … 157 Figure 47. Typical Taxiway Centerline Lighting Configuration for Standard Fillets (Centerline light spacing for operations above 1,200 feet (365 m) RVR) … 158 Figure 48. Taxiway Centerline Light Beam Orientation … 159 Figure 49. In-Pavement Runway Guard Light Configuration … 160 Figure 50. Elevated RGL and Stop Bar Configuration … 161 Figure 51. Typical Light Beam Orientation for In-Pavement RGLs and Stop Bars … 162 Figure 52.
Figure 41 · page 7Picture of the page from the copy saved here
Clearance Bar Configuration at a Low Visibility Hold Point … 163 Figure 53. Curves for Estimating Primary Load for Taxiway Centerline Lighting Systems … 164 Figure 54. Typical Elevated RGL Installation Details … 165 Figure 55. Typical In-Pavement RGL External Wiring Diagram – Power Line Carrier Communication, One Light Per Remote … 166 Figure 56. Typical In-Pavement RGL External Wiring Diagram – Power Line Carrier Communication, Multiple Lights per Remote … 167 Figure 57. Typical In-Pavement RGL External Wiring Diagram – Dedicated Communication Link … 168 Figure 58. In-Pavement RGL Alarm Signal Connection … 169 Figure 59. Controlled Stop Bar Design and Operation – “STOP” Configuration … 170 Figure 60. Controlled Stop Bar Design and Operation – Intermediate Configuration … 171 Figure 61. Controlled Stop Bar Design and Operation – “STOP” Configuration for A/C 2 … 172
AC 150/5340-30D 9/30/2008
viii
Figure 53 · page 7Picture of the page from the copy saved here
Figure 62. Typical Layout for Land and Hold Short Lights … 173 Figure 63. Typical Wireway Installation Details for Land & Hold Short Lights … 174 Figure 64. Sawing & Drilling Details for In-pavement Land & Hold Short Lights … 175 Figure 65. Typical Block Diagram for Land & Hold Short Lighting System … 176 Figure 66. Typical Curve for Determining Maximum Separation Between Vault and Control Panel with 120-volt AC Control … 177 Figure 67. Beacon Dimensions and Wiring Diagram … 178 Figure 68. Calculations for Determining Wire Size … 179 Figure 69. Typical Automatic Control … 180 Figure 70. 120-Volt AC and 48-Volt DC Remote Control … 181 Figure 71. Typical Structural Beacon Tower … 182 Figure 72. Typical Tubular Steel Beacon Tower … 183 Figure 73. Typical Pre-fabricated Beacon Tower Structure … 185 Figure 74. Typical Location of Supplemental Wind Cone … 186 Figure 75. Externally Lighted Wind Cone Assembly (Frangible) … 187 Figure 76. Typical Layout for MALSF … 188 Figure 77. Typical Layout for Runway End Identifier Lights (REILs) … 189 Figure 78. Typical ODALS Layout … 190 Figure 79.
Figure 62 · page 8Picture of the page from the copy saved here
PAPI Obstacle Clearance Surface … 191 Figure 80. PAPI Signal Presentation … 192 Figure 81. Correction for Runway Longitudinal Gradient … 193 Figure 82. General Wiring Diagram for MALSF with 120-Volt, AC Remote Control … 194 Figure 83. Typical Wiring Diagram for MALSF Controlled from Runway Lighting Circuit … 195 Figure 84. Typical Field Wiring Circuits for MALSF … 196 Figure 85. Typical Installation Details for Frangible MALS Structures – 6 foot (1.8 m) Maximum … 197 Figure 86. Typical Wiring for REILs Multiple Operation … 198 Figure 87. Typical Wiring for REIL Series Operation … 199 Figure 88. FAA L-880 Style B (Constant Current) System Wiring Diagram … 200 Figure 89. FAA L-880 Style A (Constant Voltage) System Wiring Diagram … 201 Figure 90. PAPI Light Housing Unit (LHU) Installation Detail … 202 Figure 91. Typical Installation Details for Runway End Identifier Lights (REILs) … 203 Figure 92. Configuration “A” Electrical Power … 204 Figure 93. Typical KVA Input Requirements … 205 Figure 94. Typical Wiring Diagram for Configuration “A” Electrical Power … 206 Figure 95.
Figure 80 · page 8Picture of the page from the copy saved here
Typical Equipment Layout for Configuration “A” Electrical Power … 207 Figure 96. Configuration “B” Electrical Power … 208 Figure 97. Typical Wiring Diagram for Configuration “B” Electrical Power … 209 Figure 98. Typical Wiring Diagram for Configuration “C” Power … 210 Figure 99. Flexible Pavement or Overlay Installation … 211 Figure 100. Use of Alignment Jig, No Reference Edge Available, Non-adjustable Base and Conduit System … 212 Figure 101. Use of Alignment Jig, Reference Edge Available, Non-adjustable Base and Conduit System … 213 Figure 102. In-pavement Shallow Base Runway Edge End or Threshold Light … 214 Figure 103. In-pavement Shallow Base Runway Centerline or TDZ Light … 215 Figure 104. Sawing and Drilling Details for In-Pavement Taxiway Centerline Lights … 216 Figure 105. Wiring Details for Direct- and Base-Mounted Taxiway Centerline Lights … 217 Figure 106. Typical Transformer Housing and Conduit Installation Details for Taxiway Centerline Lights … 218 Figure 107. Adjustment of Edge Light Elevation for High Snowfall Areas … 219 Figure 108.
Figure 96 · page 8Picture of the page from the copy saved here
Cable and Duct Markers … 220 Figure 109. Counterpoise Installation … 221 Figure 110. Power and Control System Block Diagram … 222 Figure 111. Typical PLC Control System Block Diagram … 223 Figure 112. PC Control System Block Diagram … 224 Figure 113. Typical Standard Details for Runway & Taxiway Edge Lights –High Intensity Light – Non-adjustable
Base-mounted … 238 Figure 114. Typical Standard Details for Runway & Taxiway Edge Lights –Medium / High Intensity Light – Non-
adjustable Base-mounted … 239
ix
Figure 115. Typical Standard Details for Runway & Taxiway Edge Lights –Medium Intensity Light – Stake-
Figure 109 · page 8Picture of the page from the copy saved here
mounted … 240 Figure 116. Typical Counterpoise and Ground Rod Connections … 241 Figure 117. Identification (ID) Tag Detail … 242 Figure 118. Standard Details for Underground Cable Installation – Typical Multiple Bank Layout … 243 Figure 119. Standard Details for Underground Cable Installation – Type A … 244 Figure 120. Standard Details for Underground Cable Installation – Type B … 245 Figure 121. Standard Details for Underground Cable Installation – Type C … 246 Figure 122. Standard Details for Underground Cable Installation – Plowed Cable … 247 Figure 123. Standard Details for Underground Cable Installation – Plowed Cable … 248 Figure 124. Standard Details for Taxiway Hold and Guidance Sign – Sign – Single Pedestal … 249 Figure 125. Standard Details for Taxiway Hold & Guidance Sign – Sign – Multiple Pedestal … 250 Figure 126. Standard Details for Taxiway Hold & Guidance Sign – Detail A … 251 Figure 127. Standard Details for Pivoting Rotating Beacon Pole – Rotating Beacon & Mounting Bracket Detail. ..252 Figure 128.
Figure 116 · page 9Picture of the page from the copy saved here
Standard Details for Pivoting Rotating Beacon Pole – Locking Device Detail … 253 Figure 129. Standard Details for Pivoting Rotating Beacon Pole – Pivot Detail … 254 Figure 130. Standard Details for Pivoting Rotating Beacon Pole … 255 Figure 131. Standard Details for Wind Cone Foundation (L-807) … 256 Figure 132. Standard Details for Wind Cone – 12 ft (3.7 m) Wind Cone … 257 Figure 133. Standard Details for Precision Approach Path Indicators (PAPIs) – PAPI Light Unit Locations … 258 Figure 134. Standard Details for Precision Approach Path Indicators (PAPIs) … 259 Figure 135. Standard Details for Precision Approach Path Indicators (PAPIs) – Section A-A … 260 Figure 136. Standard Details for Runway End Identifier Light Power & Control Derived From Runway Circuit –
Profile View … 261 Figure 137. Standard Details for Runway End Identifier Light Power & Control Derived From Runway Circuit –
Figure 129 · page 9Picture of the page from the copy saved here
Plan View … 262 Figure 138. Location of Entrance-Exit Lights (in lieu of guidance signs) … 263 Figure 139. Controlled Output Sign Block Diagram … 273 Figure 140. Typical Power Line Carrier System … 275 Figure 141. Load Example for In Pavement RGL Circuit … 280 Figure 142. ALCMS Block Diagram … 283 Figure 143. REL Configuration for Taxiways at 90 Degrees … 287 Figure 144. Angled Configuration … 288 Figure 145. Takeoff/Hold Lights … 289
Figure 138 · page 9Picture of the page from the copy saved here
LIST OF TABLES
LIST OF TABLES
Table 2-1. Straight Taxiway Edge Light Spacing … 7 Table 2-2. Edge Lighting System Design Guide … 9 Table 2-3. Equipment and Materials … 12 Table 4-1. Longitudinal Dimensions … 19 Table 4-2. Equipment and Material Used for Low Visibility Lighting Systems … 34 Table 5-1. Equipment and Material Used for Land and Hold Short Lighting Systems … 38 Table 7-1. Threshold Crossing Heights … 56 Table 7-2. Aiming of Type L-880 (4 Box) PAPI Relative to Pre-selected Glide Path … 56 Table 7-3. Aiming of Type L-881 (2 Box) PAPI Relative to Pre-selected Glide Path … 56 Table 8-1. Interface of Radio Control with Airport Visual Aids … 70 Table 13-1. AGL Control System Response Times … 109
AC 150/5340-30D 9/30/2008
x
Intentionally left blank.
CHAPTER 1. INTRODUCTION.
1.1. GENERAL.
Numerous airport visual aids are available to provide information and guidance to pilots maneuvering on airports. These aids may consist of single units or complex systems composed of many parts. Often visual aids have different performance requirements and configurations, but may share common installation procedures. For example, installation procedures for in-pavement lighting systems are essentially the same, yet the lighting systems may perform different functions. This AC provides installation details for all airport visual aids in one document. Performance specifications and configuration details for the various visual aids can be found in the referenced ACs. Drawings in Appendix 5 depict typical installation methods for various types of airport lighting equipment and are acceptable for use on projects funded with federal grant monies through the Airport Improvement Program (AIP) and with revenue from the Passenger Facility Charges (PFC) Program.
1.2. SCOPE.
This AC provides installation methods and techniques for airport visual aids. The standards contained herein are standards the FAA requires in all applications involving airport development of this nature. These standards must be met where lighting systems are required for FAA-developed procedures. Installations should conform to the National Electrical Code (NEC) and local codes where applicable. See referenced materials.
1.3. SAFETY.
Airports present a unique working environment. Airplanes traveling at high speed, multi-directional traffic, noise, and night work are a few of the conditions that may confront a construction worker on an airport. Safety is of paramount concern to all parties. We encourage you to become familiar with FAA guidance contained in AC 150/5370-2, Operational Safety on Airports During Construction.
AC 150/5340-30D 9/30/2008
Intentionally left blank.
CHAPTER 2. RUNWAY AND TAXIWAY EDGE LIGHTING SYSTEMS.
2.1. GENERAL.
Edge lighting systems are used to outline usable operational areas of airports during periods of darkness and low visibility weather conditions. These systems are classified according to the intensity or brightness produced by the lighting system.
This section covers standards for the design and installation of the following systems (see Figure 1 in Appendix I for the legend for Figures 2 – 22):
Runway Edge Lighting Systems. Runway edge lights define the edge of the runway. The following standard systems are described in this section:
LIRL - low intensity runway lights MIRL - medium intensity runway lights HIRL - high intensity runway lights
Taxiway Edge Lighting Systems. Taxiway edge lights define the edge of the taxiway. The standard taxiway edge lighting system for airports is described in this section:
MITL - medium intensity taxiway lights
2.1.1. Selection Criteria.
The selection of a particular edge lighting system is generally based on the operational needs per the following guidelines:
LIRL - install on visual runways (for runways at small airports), MIRL - install on visual runways or non-precision instrument runways, HIRL - install on precision instrument runways, MITL - install on taxiways and aprons at airports where runway lighting systems are installed.
As stated, the above are general selection criteria. However, the airport surface requirements for specific approach procedures are the determining factor for system selection. See AC 150/5300-13, Airport Design, Appendix 16, New Instrument Approach Procedures, for more information. Any edge lighting system requires that the airport be equipped with a rotating beacon meeting the requirements of AC 150/5345-12, Specification for Airport and Heliport Beacons.
2.1.2. Runway Edge Light Configurations.
A runway edge lighting system is a configuration of lights that defines the lateral and longitudinal limits of the usable landing area of the runway. Two straight lines of lights installed parallel to and at equal distances from the runway centerline define the lateral limits. The longitudinal limits of the usable landing area are defined at each end of the area by straight lines of lights called threshold/runway end lights, which are installed perpendicular to the lines of runway edge lights. Table 2-3, Equipment and Materials, provides information on the recommended light fixture for each application.
a. Edge Lights.
(1) Colors.
AC 150/5340-30D 9/30/2008
(a) LIRL. The runway edge lights emit white light as shown in Figure 2.
(b) MIRL and HIRL. The runway edge lights emit white light, except in the caution zone,
(not applicable to visual runways) which is the last 2,000 feet (610 m) of runway or onehalf the runway length, whichever is less. In the caution zone, yellow lights are substituted for white lights; they emit yellow light in the direction facing the instrument approach threshold and white light in the opposite direction. Instrument approach runways are runway end specific, meaning a runway may have an instrument approach on one end and a non-instrument approach on the opposite end. However, when there is an instrument approach at each runway end, yellow/white lights are installed at each runway end in the directions described above. The yellow lights indicate caution on rollout after landing. An example is shown in Figure 3.
(2) Location and Spacing.
(a) General. The runway edge lights are located on a line parallel to the runway centerline at
least 2 ft (0.6 m), but not more than 10 ft (3 m), from the edge of the full strength pavement designated for runway use. On runways used by jet aircraft, we recommend 10 ft (3 m) to avoid possible damage by jet blasts. On runways not used by jet aircraft, we recommend 2 ft (0.6 m). The edge lights are uniformly spaced and symmetrical about the runway centerline, such that a line between light units on opposite sides of the runway is perpendicular to the runway centerline. Longitudinal spacing between light units must not exceed 200 ft (61 m), except as described in paragraph 2.1.2a(2)(b)1 below. Use the threshold/runway end lights as the starting reference points for longitudinal spacing calculations during design.
NOTE: See AC 150/5340-26, Maintenance of Airport Visual Aid Facilities, for additional information about the toe-in of runway edge light fixtures. Follow the manufacturer’s instructions for proper fixture toe-in alignment.
(b) Intersections.
1. LIRL/MIRL. For runways with MIRL or LIRL installed and where the configuration of the runway intersection does not allow for the matching of the runway edge lights on opposite sides of the runway to be maintained, the distance between light units on the same side of the runway must not exceed 400 ft (122 m). On the side of the runway opposite the intersection, install a single elevated runway edge light unit maintaining the designed spacing shown in Figure 2. For MIRL, if the distance between the runway edge lights units is greater than 400 ft (122 m), install an L-852D, Taxiway Centerline fixture for Category (CAT) III (specified in AC 150/5345-46, Specification for Runway and Taxiway Light Fixtures), light fixture modified to produce white light (by removing the filters) and maintain the designed spacing shown in Figure 3.
2. HIRL. For runways approved for instrument landing system (ILS) CAT III operations with HIRL installed at runway intersections, install L-850C, flush in-pavement light fixtures (described in AC 150/5345-46), to maintain uniform spacing. For other operations on runways with HIRL, the installation of a semi-flush fixture should be based on the following:
a. The availability of other visual cues at the intersection, such as guidance signs or
centerline lighting.
b. The geometric complexity of the intersection, such as crossing runways. When
the gap exceeds 400 feet install an in-pavement light fixture to maintain uniform spacing.
c. Whether the addition of a semi-flush fixture could confuse ground operations.
(c) Runway Sections Used as Taxiways. For runway or sections of runways used as taxiways,
the runway/taxiway must have the specified runway lights with the designed spacing maintained on the dual purpose area. Taxiway edge lights are permitted to be installed on the dual purpose area. However, taxiway centerline lighting compliant with Chapter 4 is preferred. In either case, the control system must not allow the taxiway lights and the runway lights to be on concurrently. The control systems must be designed such that either the taxiway lights or the runway lights are on, but never may both runway and taxiway lights be illuminated at the same time. NOTE: The lights on the entire runway should be off when the taxiway lights are illuminated. See Figure 21 and Figure 22. In some cases where a section of the runway is used as a taxiway, it may be desirable to install a controllable stop bar to prevent taxiing aircraft from entering an intersecting runway; the stop bar should be interlocked with the taxiway lights so that it is on when the taxiway lights are on.
b. Threshold/Runway End Lights.
(1) Color.
(a) Runway Thresholds. Threshold lights emit green light outward from the runway and emit
red light toward the runway to mark the ends of the runway. The green lights indicate the landing threshold to landing aircraft and the red lights indicate the end of the runway, both landing and departing. These lights are usually combined into one fixture and special lenses or filters are used to emit the desired light in the appropriate direction. The layout details for runway threshold lights are shown in Figure 2, Figure 3, Figure 4, and Figure 5.
(b) Displaced Runway Thresholds. When the runway threshold is displaced, the lights located
in the area before the threshold emit red light toward the approach. The threshold lights located at the displaced threshold emit green light outward from the runway threshold. Examples of threshold lighting when the landing threshold is displaced from the actual runway threshold are shown in Figure 6. Refer to AC 150/5300-13, Changes 1 through 11, Airport Design, Appendix 2 (Change 10 dated 09/29/2006), paragraph 2c, and Appendix 14 (Change 4 dated 11/10/94), paragraph 2(c)2 for additional information about obstructions with regard to displaced thresholds and declared distances.
(2) Location and Spacing.
EXCEPTION: The FAA Airport Engineering Division is reviewing the current standard for inboard/outboard runway and threshold end lights. Existing configurations of inboard/outboard runway and threshold end lights installed per this AC may remain in place until a new standard is issued. If a new standard is issued, the FAA will require that such systems be upgraded within a reasonable time.
AC 150/5340-30D 9/30/2008
(a) General. The combination threshold and runway end lights are located on a line
perpendicular to the extended runway centerline not less than 2 ft (0.6 m) and not more than 10 ft (3 m) outboard from the designated runway threshold. The lights are installed in two groups located symmetrically about the extended runway centerline. The outermost light in each group is located in line with the runway edge lights. The other lights in each group are located on 10 ft (3 m) centers toward the extended runway centerline. Coordinate locations and spacing of threshold/runway end lights with other plans for future lighting equipment. Approach lighting systems are equipped with threshold lighting located 2 ft (0.6 m) to 10 ft (3 m) from the threshold. If other airport navigational equipment installed at the threshold prevents the lights from being properly spaced, each light in a group may be offset not more than 1 ft (0.3 m) in the same direction.
1. Runways with LIRL/MIRL. Threshold/runway end lights installed on visual runways with LIRL or MIRL must have 3 lights in each group per Figure 2.
2. Runways with MIRL/HIRL. Threshold/runway end lights installed on non-precision instrument runways with MIRLs and precision instrument runways with HIRLs must have 4 lights in each light group per Figure 3.
(b) Displaced Threshold. When the threshold is displaced from the end of the runway or
paved area, and access by aircraft prior to the threshold is allowed, the threshold lights are located outboard from the runway as shown in Figure 6. The innermost light of each group is located in line with the line of runway edge lights, and the remaining lights are located outward, away from the runway, on 10 ft (3 m) centers on a line perpendicular to the runway centerline. When the displaced runway area is usable for takeoff, red runway edge lights are installed to delineate the outline of this area, as shown in Figure 6.
(c) Runways Where Declared Distances are Adjusted. Airport designs for constrained
airports may require implementation of runway declared distance concepts to meet runway safety area (RSA), runway object free area (ROFA) or the runway protection zone (RPZ) standards contained in AC 150/5300-13, Airport Design. The criteria for selecting the applicable configuration are described in AC 150/5300-13. The marking for declared distance runways must comply with the specification described in AC 150/5340-1, Standards for Airport Markings, and signing must comply with the standards in AC 150/5340-18, Standards for Airport Sign Systems. For configurations not covered by this AC contact the FAA Airports Regional Office for guidance. Guidance for Declared Distances is provided in Appendix 1 of this AC in Figures 7 thru 15.
2.1.3. Stopway Edge Lights
2.1.3. Stopway Edge Lights
Definition of a stopway: A stopway is an area beyond the takeoff runway, centered on the extended runway centerline, and designated by the airport owner for use in decelerating an airplane during an aborted takeoff. It must be at least as wide as the runway and able to support an airplane during an aborted takeoff without causing structural damage to the airplane. See Figures 11 and 12 for illustrations of stopways.
a. Color. The stopway edge lights emit unidirectional red light in the takeoff direction of the
runway.
b. Location and Spacing. Stopway lights are placed along its full length in two parallel rows that
are equidistant from the runway centerline and coincident with the rows of runway edge lights. The spacing between the lights and distance from the edge is the same as runway edge lights per paragraph 2.1.2. Lights must also be placed at the end of the stopway (spaced symmetrically in relation to the extended runway centerline) and no more than 10 feet (3 m) outboard of the stopway edge per Figures 11 and 12. For visual runways with LIRL/MIRL, use two groups of three lights. For non-precision and precision instrumented runways use two groups of 4 lights.
2.1.4. Taxiway Edge Light Configurations.
Taxiway edge lighting systems are configurations of lights that define the lateral limits of the taxiway.
a. Color. The taxiway edge lights emit blue light, and edge reflectors reflect blue.
b. Location and Spacing. Fixtures in the edge lighting system are located in a line parallel to the
taxiway centerline not more than 10 ft (3 m) outward from the edge of the full strength pavement. See Figure 107 for additional details about fixture height versus lateral location requirements. Reflectors may be installed per paragraph 2.1.3.c of this section in lieu of, or to enhance, taxiway edge lights. The spacing for taxiway edge lights is calculated based on the taxiway configuration. The methods of calculating taxiway edge light spacing are described below:
NOTE: The use of in-pavement taxiway edge lighting fixtures should be restricted to where elevated lights may be damaged by jet blast or where they interfere with aircraft operations.
(1) Straight Sections. The edge lights are spaced symmetrically using the criteria outlined in
Table 2-1, Straight Taxiway Edge Light Spacing. Lights installed on opposite sides of a straight taxiway are aligned such that opposing lights are in a line perpendicular with the taxiway centerline. Examples of taxiway lighting for straight taxiway section are shown in Figure 16, Figure 18, and Figure 19.
Table 2-1. Straight Taxiway Edge Light Spacing.
Section Length (L)
Number, Edge Lights (N)
(per side)1
Maximum Spacing (Max)
Spacing (S)
L ≤ 50 ft (15 m) 2
50 ft (15 m) L
L > 50 ft (15 m) and L
≤ 100 ft (30 m)
3
50 ft (15 m) L/2
L > 100 ft (30 m) and L
≤ 200 ft (61 m)
3 [(L/max) + 1]2 ,3
100 ft (30 m) 50 ft (15 m) (single edges) 3 L/2 L/(N-1) 3 L > 200 ft (61 m) [(L/max) + 1]2
100 ft (30 m) (single edges) 3 200 ft (61 m)
L/(N-1)
1 Number (N) excludes lights required for end and entrance/exit indicators. 2 Round value up to the next whole number, i.e. 1.31 becomes 2. 3 Applies to single straight taxiway only, where only one side exists. See Figure 18 and Figure 19.
(2) Curved Sections. Curved taxiway edges require shorter spacing of edge lights. The spacing is
determined based on the radius of the curve. The applicable spacing for curves is shown in Figure 17. The taxiway edge lights are uniformly spaced. Curved edges of more than 30
AC 150/5340-30D 9/30/2008
degrees from point of tangency (PT) of the taxiway section to PT of the intersecting surface must have at least three edge lights. For radii not listed in Figure 17 determine spacing by linear interpolation. Taxiway spacing on curved sections at other than 14 CFR Part 139, Certifications and Operations: Land Airports Serving Certain Air Carriers, and certificated airports may be reduced as shown in Figure 17. In such cases, like curves on an airport will have the same spacing.
(3) Intersections. Install end indicators on straight taxiway sections 200 ft (61 m) or longer. End
indicators are additional taxiway edge lights installed before the intersection spaced 50 ft (15 m) from the last light on straight taxiway sections. These lights are installed on sections of taxiways that are more than 200 ft (61 m) long, where edge light spacing exceeds 60 ft (18 m). Figure 18 and Figure 19 show typical placement of end indicators.
(4) Runway-Taxiway Intersections. Taxiway guidance signs are installed at runway-taxiway
intersections to define the throat or entrance into the intersecting taxiing route. Where taxiway signs would interfere with aircraft operations, or at small general aviation (GA) airports, dual taxiway lights spaced as shown in Appendix 5, Figure 138, may be installed instead of the sign. The taxiway lights used are L-861T fixtures. Taxiway lights used per the above must be illuminated when the runway edge lights are on.
c. Use of Reflectors. Reflectors are permitted to enhance taxiway lighting systems installed on short
taxiway sections, curves and intersections (see Figure 16 and Figure 17). In such cases, lights are installed to meet the spacing requirements and reflectors are installed uniformly between the lights. Reflectors are also permitted in lieu of edge lights where a centerline system is installed. In such cases, reflectors must be installed using the required spacing for taxiway edge lights as specified in this AC. Specified reflectors are described in AC 150/5345-39, FAA Specification L- 853, Runway and Taxiway Retroreflective Markers.
2.1.5. System Design.
Coordinate the lighting system design with the existing and future airport plans. Airport drawings will show existing system(s) layout and available utilities. Install the conduits and ducts needed for the lighting system prior to paving operations to eliminate the expense of installing these utilities in existing pavement. Airport drainage systems may influence the location of cable ducts and trenches. Develop design drawings showing the dimensional layout of the lighting system prior to construction. Examples of system layouts are shown in Figure 20, Figure 21, and Figure 22, for high density traffic airports.
a. Lighting Fixtures. The lighting fixtures installed in the edge lighting systems are either base-
mounted or stake-mounted. Base mounts are used for either elevated fixtures or in-pavement fixtures. In-pavement fixtures are not permitted for the full length of the runway. They are typically used in areas where aircraft may roll over the fixture and require load-bearing bases. Stake mounting is typically less expensive than base mounting; however, base mounting provides additional protection for this equipment and makes the equipment more accessible for maintenance. Stake mounting requires the transformers, cables and connectors be buried in the earth. A typical drawing of fixture mountings is shown on Figure 23. Base-mounted fixtures must be installed using series circuits only and are recommended for HIRL, MIRL, or MITL. Stakemounted fixtures can be installed with either series or parallel circuits.
b. Electrical Power (Series vs. Parallel Circuits). Series powered circuits with isolation transformers
are recommended for the HIRL, MIRL, and MITL lighting systems. The advantages of the series circuits are: 1) uniform lamp brightness, 2) lower installation cost for long runways, generally
over 4,000 ft long, 3) reduced cold-start burnouts and in-rush currents on turn-on, and 4) unintentional grounding will not shut the system down. Parallel power circuits are recommended for LIRL, but may also be used for MIRL or MITL. Parallel circuits have a lower installation cost for short runways, 4,000 ft or less. Parallel circuits should be designed using a 120/240V, singlephase, 3-wire system with a shared neutral. Interleave the circuits so that each adjacent fixture is on a separate leg. Series circuits may also be interleaved, considering requirements for equipment such as regulators and adjacent lamp monitoring during design of the system. If two or more circuits are used to power the edge lights for one runway and loss of power to any of those circuits will leave more than 400 ft of the runway without edge lights, the circuits should be coupled such that if one is energized both are energized, or if one is de-energized both are de-energized.
c. Power Source and Monitoring. Series powered airport lighting circuits are powered by constant
current regulators (CCRs). The regulators and the associated monitoring system are described in AC 150/5345-10, Specification for Constant Current Regulators and Regulator Monitors. The CCRs are designed to provide the desired number of brightness steps. Some regulators, particularly Silicon Controlled Rectifier (SCR) designs, emit electromagnetic interference (EMI) that may degrade the performance of other air navigational equipment, such as computers, radars, instrument landing systems, radio receivers, very high frequency omnidirectional radio ranges, etc. See Appendix II for more information. Runway edge lighting systems that support CAT II or CAT III operations should be remotely monitored and must provide the monitoring information to the Airport Traffic Control Tower (ATCT). The monitoring systems must be capable of detecting if more than 10 percent of the lights are inoperative.
Table 2-2. Edge Lighting System Design Guide.
Installation Associated Threshold Lightin
g System
Type Mounting
Fixture Power System
Number
of Steps Design Fixtures
RUNWAY EDGE LIGHTING Inset 1 Base L-850C HIRL Elevated Base or Stake L-862 Series 5 8 lights L-862E
Inset 1 Base Series MIRL Elevated Base or Stake L-861 L-852D
Series or
Parallel
3 6 or 8 lights
L-861SE2
L-861E2
LIRL
Elevated
Base or Stake
L-860
Series or
Parallel
1 6 lights L-860E
TAXIWAY EDGE LIGHTING Inset Base L-852T Series 3 MITL Elevated Base or Stake L-861T Series or
Parallel
3
1 Inset fixtures are not permitted for the full length of the runway. They are typically installed in areas where aircraft may roll over the fixture. 2 For runways with either a Precision Approach Path Indicator (PAPI), runway end identifier lights (REIL), medium approach light system (MALS), or lead-in lighting system (LDIN), L- 861E light fixture may be installed in lieu of the L-861SE.
d. Brightness Steps. The brightness of the lamps is specified in steps that are defined as a percentage
of the full brightness of the lamp. (AC 150/5345-46 contains the specifications for the light
AC 150/5340-30D 9/30/2008
fixtures.) The following tables specify the appropriate lamp current or voltage to achieve each brightness step:
(1) High Intensity Systems. The HIRL have five brightness steps as follows:
Percent Brightness
Lamp Current Step 5 100 6.6 A Step 4 25 5.2 A Step 3 5 4.1 A Step 2 1.2 3.4 A Step 1 0.15 2.8 A
(2) Medium Intensity Systems. The MIRL and MITL, when installed using a series circuit and
powered by an L-828 or L-829 regulator, have three brightness steps as follows:
Percent Lamp Current Brightness Series Parallel Step 3 100 6.6 A 120 V Step 2 30 5.5 A 85 V Step 1 10 4.8 A 60 V
When MITL are installed using a parallel circuit, only one brightness step is required, although it may be desirable to provide equivalent brightness steps as obtained with the series circuit. This may be accomplished by use of a variable transformer, auto-transformer, or other means.
(3) Low Intensity Systems. The LIRL have only one brightness step, 100%.
e. Control Methods. The edge lighting systems should have provisions for local and/or remote
control methods. Remote controls are recommended for locations served by a control tower, flight service station, or other manned offices where the system(s) operates. Refer to Chapter 13 for additional information on control systems.
(1) Local Control. Local controls may be designed using direct switching at the site or automatic
controls such as a photoelectric control device or timer switch with provisions for switching from automatic to manual control.
(2) Remote Control. Remote controls may be designed using a fixed-wire method or radio control
with L-854 equipment as specified in AC 150/5345-49, Specification L-854, Radio Control Equipment. Figure 24, Figure 25, Figure 26, Figure 27, Figure 28, Figure 29, and Figure 30 show some typical applications for remote controls.
(a) 120 Volts AC. Where the distance between the remote control panel and the vault is not
great enough to cause an excessive voltage drop (5%) in the control leads, the standard control panel switches should be used to operate the control relays directly. Control relays supplying power to the regulators must have coils rated for the control voltage. Conductor size of the control cable should be of a size that will not cause more than a 5% voltage drop. The voltage rating of the conductor insulation must be rated for the system voltage. Refer to Chapter 13 for additional guidance.
(b) 120 Volts AC – Auxiliary Relay. Special low-burden pilot auxiliary relays, having proper
coil resistance to reduce control current, may be used to obtain additional separation distance with 120 volt AC control circuits. It may be advantageous to use these relays to expand existing 120 volt AC control circuits.
(c) 48 Volts DC. Where the distance between control panel and the vault would cause an
excessive voltage drop, a low voltage (48 volt DC) control system should be used. In such a system, remote control panel switches activate sensitive pilot relays, such as those specified in AC 150/5345-13, Specification for L-841 Auxiliary Relay Cabinet Assembly for Pilot Control of Airport Lighting Circuits, which, in turn, control the regulator relays. Use an appropriately sized cable, of a type listed for use as direct earth burial, to connect the control panel to the pilot relays. The DC control system is adequate for up to 7,900 feet (2408 m) separation between control point and vault. For typical application details, see Figure 29, Figure 30 and AC 150/5345-3, Specification for L-821 Panels for Control of Airport Lighting.
f. Runway Visual Range (RVR) Connections. Where RVR equipment is to be installed, provide two
No. 12 AWG wires for 120-volt control, or two No. 19 wires if 48-volt control is used, between the control tower and the vault. The wires in the vault connect to an interface unit provided with the RVR equipment. The wires in the tower connect to RVR equipment. All RVR connections must be per instructions provided with the RVR system and made by personnel responsible for the RVR or their designee.
2.1.6. Equipment and Materials.
Equipment and material covered by FAA ACs are referred to by item numbers and the associated AC numbers where the equipment is specified. All pertinent ACs and specifications are referenced by number and title in Appendix 4. Equipment not covered by FAA specifications, such as distribution transformers, circuit breakers, cutouts, relays, and other commercial items of electrical equipment, must conform to the applicable rulings and standards of the electrical industry and local code regulations. Electrical equipment must be tested and certified by an Occupational Safety and Health Administration (OSHA) recognized Nationally Recognized Testing Laboratory (NRTL) and should bear that mark. A current list of NRTLs can be obtained by contacting the OSHA NRTL Program Coordinator. Table 2-3 contains a list of equipment and material used for runway and taxiway edge lighting systems described in this section. See Chapter 12 for additional information.
a. Light Bases, Transformer Housings and Junction Boxes. See paragraph 12.2. b. Duct and Conduit. See paragraph 12.3. c. Cable, Cable Connectors, Plugs and Receptacles. See paragraph 12.4. d. Counterpoise (Lightning Protection). See paragraph 12.5. e. Safety (Equipment) Ground. See paragraph 12.6. f. Concrete. See paragraph 12.7. g. Steel Reinforcement. See paragraph 12.8. h. Adhesive and Sealants. See paragraph 12.9. i. Load-bearing Lighting Fixtures. See paragraph 12.10 j. Inspection. See paragraph 12.11. k. Testing. See paragraph 12.12. l. Auxiliary Relays. See paragraph 12.13. m. Vault. See paragraph 12.14. n. Maintenance. See paragraph 12.15.
AC 150/5340-30D 9/30/2008
Table 2-3. Equipment and Materials.
Item Description Item No. ACs or Specifications Auxiliary Relay Cabinet L-841 AC 150/5345-13 Cable L-824 AC 150/5345-7 Cable Connectors L-823 series circuits L-108 parallel circuits
AC 150/5345-26 AC 150/5370-10 Circuit Selector Switch L-847 AC 150/5345-5 Control Panel L-821 AC 150/5345-3 Elevated Edge Light Fixture (HIRL) L-862, L-850C1 AC 150/5345-46 Elevated Edge Light Fixture (LIRL) L-860 AC 150/5345-46 Elevated Edge Light Fixture (MIRL) L-861 AC 150/5345-46 Elevated Threshold Light Fixture (HIRL) L-862 AC 150/5345-46 Elevated Threshold Light Fixture (MIRL) L-861 SE, L861E 2 AC 150/5345-46 In-pavement Light Fixture L-852 AC 150/5345-46 In-pavement Light Fixture L-850C, D, E AC 150/5345-46 Isolation Transformers L-830 AC 150/5345-47 Junction Box4 L-867/L-868, blank covers
Light Base and Transformer Housing 3 L-867, L-868 AC 150/5345-42 Regulators L-828, L-829 AC 150/5345-10 Retroreflective Markers L-853 AC 150/5345-39 Duct and Conduit L-110 AC 150/5370-10 Concrete P-610 AC 150/5370-10 Tape L-108 AC 150/5370-10 Vaults L-109 AC 150/5370-10 1 Install the L-850 C light fixture if in-pavement fixtures are applicable, per paragraph 2.1.2. 2 For runways with either a Precision Approach Path Indicator (PAPI), runway end identifier lights (REIL), medium approach light system (MALS), or lead-in lighting system (LDIN), L-861E light fixture may be installed in lieu of the L-861SE. 3 Elevated lights are installed with a 12 inch (size B) base or are stake-mounted, and inpavement light fixtures are installed with a 15 inch (size C) base or a 12 inch (size B) L- 868 base. 4 Use an L-867 light base with blanking cover for a junction box or transformer housing that must withstand occasional light vehicular loads. Use an L-868 light base with blanking cover for a junction box or transformer housing that must withstand heavy loads from vehicles or aircraft.
CHAPTER 3. RUNWAY CENTERLINE AND TOUCHDOWN LIGHTING SYSTEMS.
3.1. INTRODUCTION.
Runway centerline and touchdown zone lighting systems are designed to facilitate landings, rollouts, and takeoffs. The touchdown zone lights are primarily a landing aid while the centerline lights are used for both landing and takeoff operations.
3.2. SELECTION CRITERIA.
Runway centerline lights and touchdown zone lights are required for CAT II and CAT III runways and for CAT I runways used for landing operations below 2,400 feet (750 m) RVR. Runway centerline lights are required on runways used for takeoff operations below 1,600 feet (480 m) RVR. Although not operationally required, runway centerline lights are recommended for CAT I runways greater than 170 feet (50 m) in width or when used by aircraft with approach speeds over 140 knots.
3.3. CONFIGURATION.
a. Runway Centerline Lighting.
(1) Location. The runway centerline lights are located along the runway centerline at 50 foot (15
m) longitudinal intervals per Figure 33. The line of runway centerline lights may be uniformly offset laterally to the same side of the physical runway centerline a maximum of 2.5 feet (0.8 m) measured from the physical runway centerline to the fixture centerline. For any new runway, the light base installation must be no closer than 2 feet (0.6 m) (measured to the edge of the fixture base) to any pavement joints. Runway extensions of existing runways must use the convention already established for that runway. See Section 4.3 and Figure 45 for additional information about the taxiway centerline lighting location requirements related to runway centerline lights for major taxiway turnoffs. See AC 150/5340-1J, Standards for Airport Markings, for additional information about runway centerline marking widths and location.
(2) Color Coding. The last 3,000-foot (900 m) portion of the runway centerline lighting system is
color coded to warn pilots of the impending runway end. Alternating red and white lights are installed, starting with red, as seen from 3,000 feet (900 m) to 1,000 feet (300 m) from the runway end, and red lights are installed in the last 1,000 foot (300 m) portion.
(3) Displaced Threshold. On runways having centerline lights, the centerline lights are extended
into the displaced threshold area. If the displaced area is less than 700 feet (110 m) in length, the centerline lights are blanked out in the approach direction. For displaced threshold areas over 700 feet (110 m) in length, the centerline lights in the displaced area are circuited separately from the centerline lights in the non-displaced runway area to permit turning “off” the centerline lights in the displaced area during landing operations. If the displaced threshold area also contains a medium intensity approach light system, the control of the approach lights and displaced threshold area centerline lights is interlocked to ensure that when the approach lights are “on”, the displaced area centerline lights are “off”, and vice versa. If the displaced threshold area contains a high intensity approach lighting system, separate circuiting of the centerline lights in the displaced area is not required since the high intensity approach lights will “wash out” the centerline lights.
AC 150/5340-30D 9/30/2008
b. Touchdown Zone Lighting. Touchdown zone lights consist of 2 rows of transverse light bars
located symmetrically about the runway centerline per Figure 34. Each light bar consists of 3 unidirectional lights facing the landing threshold. The rows of light bars extend to 3,000 feet (900 m), or one-half the runway length for runways less than 6,000 feet (1 800 m), from the threshold with the first light bars located 100 feet (30 m) from the threshold. The light beam of the touchdown zone lights is toed four degrees toward the runway centerline. This is achieved by either installing light fixtures that have had their optical assembly toed four degrees, or by angling the light base four degrees and installing the light fixture.
3.4. DESIGN.
a. Sequence of Installation. The installation of in-pavement lights should be done, if possible, while
the runway is under construction or when an overlay is made. This allows for the installation of L- 868 light base and transformer housings with a conduit system, which is preferred. Even though lighting may not be programmed at the time of runway paving or overlay, installation of bases and a conduit system should be considered for future installation of in-pavement lighting. Installation of the lighting system after paving is completed is very costly and requires a lengthy shutdown of the runway.
b. Layout. Provide a design drawing showing the dimensional layout of the centerline and
touchdown zone lighting systems prior to construction. Correlate this design with current airport drawings to utilize available ducts and utilities and to avoid conflict with existing or planned facilities.
c. Runway Centerline and Touchdown Zone.
(1) Light Fixtures and Wires. Design these systems for one of the following conditions:
(a) In new pavements, provide access to cables and transformers through the use of conduits
and L-868 transformer bases. This type of installation will reduce downtime and repair costs when the underground circuits require maintenance. See Figure 35, Figure 36, and Figure 37.
(b) In pavements being overlaid, a base and conduit system as shown in Figure 35 and Figure
36 may be used. This provides the advantages listed in (a) above.
(c) In existing pavements, provide recesses or holes for the light fixtures and shallow sawed
wireways for electrical conductors. This method does not require the installation of bases and conduits. See Figure 38, Figure 39, Figure 40, Figure 41, and Figure 42.
(d) In existing pavements, the directional boring of a raceway under the pavement along the
lighting route is permitted. Core drill a 3 feet (0.91 m) diameter hole at the light location. Install L-868 light bases in the cored hole and connect conduit.
(2) Electric Power. Design each system as a 20-ampere or 6.6-ampere series circuit using a CCR.
Provide each light fixture with an isolation transformer sized by the manufacturer to match the lamp. To estimate the size (Kw (kilowatt) capacity) of the CCR, allow for the total load for each fixture, as calculated in paragraph 3.4d(1), plus losses in the feed cable from the regulator around the entire loop. Use a 6.6-ampere primary circuit if the total load is 30 Kw or less, and a 20-ampere primary circuit if the total load is over 30 Kw.
(3) Electrical Control. Make the centerline lighting system controls independent of the
touchdown zone lighting system and the high intensity runway edge lights. A normal control circuit is 120 VAC; see special considerations in the next paragraph. We recommend including a minimum of 20% spare wires in the control cable for future use. Refer to Chapter 13 for additional information on control systems.
d. Special Considerations.
(1) The total load of a fixture is calculated as follows:
( ) ( ) ⎥⎦
⎤ ⎢⎣
⎡
⎥⎦
⎤ ⎢⎣
⎡ ⎟⎠ ⎞ ⎜⎝ ⎛ × − × +
100 100 1 or rPowerFact Transforme y rEfficienc Transforme LampWatts LampWatts
Transformer power factor and efficiency is given in percentage, and is specified in AC 150/5345-47, Isolation Transformers for Airport Lighting Systems.
(2) Voltage drop between control tower and regulator must be considered. Control voltage at the
regulator must be 100 volts (minimum). If this voltage cannot be maintained, either an auxiliary low current AC relay must be installed at each regulator or a low voltage DC remote control circuit must be used. In some instances, it will be more economical, because of material costs, to install a low voltage DC control circuit even though the voltage drop is within acceptable limits with the standard 120 VAC system. Refer to Chapter 13 for additional information on control systems.
3.5. EQUIPMENT AND MATERIAL.
a. Specifications and Standards.
(1) Equipment and material covered by specifications are referred to by AC numbers.
(2) Distribution transformers, oil switches, cutouts, relays, terminal blocks, transfer relays, circuit
breakers, and all other commercial items of electrical equipment not covered by FAA specifications must conform to the applicable rulings and standards of the applicable National Fire Protection Association (NFPA) 70, NEC.
b. Light Fixtures.
(1) Provide runway centerline light fixtures per AC 150/5345-46, L-850A (Bidirectional).
(2) Provide touchdown zone light fixtures per AC 150/5345-46, L-850B (Unidirectional).
c. Isolation transformers. Provide isolation transformers, L-830 (60 Hz) or L-831 (50 Hz), per AC
150/5345-47. The transformers serve as a means of insulating the light unit from the high voltage of the series circuit. When a lamp filament opens, the continuity of the primary series circuit is maintained by the isolation transformer.
d. Light Base and Transformer Housings. Where required, provide L-868 bases per AC 150/5345-
42, Airport Light Bases, Transformer Housing, Junction Boxes, and Accessories. The bases consist of a cylindrical body with top flange and cable entrance hubs; an internal grounding lug may be specified by the user. The internal grounding lug is used where bases are interconnected
AC 150/5340-30D 9/30/2008
with the duct and the ground wire is installed through the duct system. Certain applications may require additional entrance hubs. Provide necessary covers per AC 150/5345-42.
e. Regulators. Provide L-828 and L-829 CCRs per AC 150/5345-10. The regulator is designed for
step brightness control without interrupting load current. The assembly has lightning arresters, open circuit and over current protective devices, and a local control switch. All parts are suitably wired at the factory as a complete assembly. Series disconnects are required but are not furnished with the regulator; various ratings are available.
f. Control Panel. System controls may be installed in the existing control panel if space is available.
Otherwise, provide an L-821 remote control panel per AC 150/5345-3. The panel consists of a top panel plate and housing, toggle switches, terminal boards, and brightness controls, as required. The site of the panel and the number of components to be mounted on the panel must be specified for each installation. In areas where lightning is prevalent, lightning arrestors should be installed at the terminal points of this panel.
g. Auxiliary Relay Cabinet. L-841 auxiliary relay cabinet assemblies, manufactured per AC
150/5345-13, can be obtained for use in 48-volt DC control circuits. The assembly consists of an enclosure containing a DC power supply, control circuit protection, and 20 pilot relays. In areas where lightning is prevalent, lightning arresters should be installed at the terminal points of this cabinet.
See Chapter 12, Equipment and Material, for additional information.
a. Light Bases, Transformer Housings and Junction Boxes. See paragraph 12.2. b. Duct and Conduit. See paragraph 12.3. c. Cable, Cable Connectors, Plugs and Receptacles. See paragraph 12.4. d. Counterpoise (Lightning Protection). See paragraph 12.5. e. Safety (Equipment) Ground. See paragraph 12.6. f. Concrete. See paragraph 12.7. g. Steel Reinforcement. See paragraph 12.8. h. Adhesive and Sealants. See paragraph 12.9. i. Load-bearing Lighting Fixtures. See paragraph 12.10 j. Inspection. See paragraph 12.11. k. Testing. See paragraph 12.12. l. Auxiliary Relays. See paragraph 12.13. m. Vault. See paragraph 12.14. n. Maintenance. See paragraph 12.15.
CHAPTER 4. TAXIWAY LIGHTING SYSTEMS.
4.1. INTRODUCTION.
Other taxiway lighting systems such as taxiway centerline lights, runway guard lights (RGLs), stop bars, and clearance bars are designed to facilitate taxiing and may be required for airport operations during low visibility conditions. Coordinate these systems with Flight Standards and Air Traffic Control (ATC) for all low visibility operations:
a. Taxiway Centerline lights. Taxiway centerline lights provide taxi guidance between the runway
and apron areas.
b. Runway Guard Lights. RGLs provide a visual indication to anyone approaching the runway
holding position that they are about to enter an active runway.
c. Stop Bars. Stop bars provide a distinctive "stop" signal to anyone approaching a runway.
(1) In low visibility conditions, controlled stop bars are used to permit access to the active
runway. Uncontrolled stop bars protect the active runway at taxiway/runway intersections that are not part of the low visibility taxi route. Stop bars are required for operations below 600 feet (183 m) RVR on illuminated taxiways that provide access to the active runway.
(2) Stop bars may also be used as a means of preventing runway incursions regardless of visibility
conditions. For example, stop bars could be illuminated in certain airfield configurations that would prevent aircraft access from particular taxiways to active, as well as closed runways.
d. Clearance Bars. Clearance bars serve two purposes:
(1) In low visibility, clearance bars advise pilots and vehicle drivers that they are approaching a
hold point (other than a runway holding position). They are installed at designated hold points on the taxiway for operations below 600 feet (183 m) RVR.
(2) At night and in inclement weather, clearance bars advise pilots and vehicle drivers that they
are approaching an intersecting taxiway. They are generally installed at taxiway intersections where the taxiway centerline lights do not follow the taxiway curve, as depicted in Figure 43, and where taxiway edge lights are not installed.
4.2. IMPLEMENTATION CRITERIA.
Airports approved for air carrier operations below 1,200 feet (365 m) RVR are required to have some or all of the various lighting systems (taxiway centerline lights, RGLs, stop bars, and clearance bars) discussed in this chapter per the criteria in AC 120-57, Surface Movement Guidance and Control System (SMGCS), and the FAA-approved SMGCS plan.
In addition, taxiway centerline lights, RGLs, and stop bars may be installed where a taxiing problem exists. Such problems include, but are not limited to, the following:
a. Runway Incursions.
(1) RGLs provide runway incursion protection regardless of visibility conditions and are
recommended at runway holding positions to enhance the conspicuity of the hold position at
AC 150/5340-30D 9/30/2008
problem intersections or where recommended by an FAA Runway Safety Action Team (RSAT).
(2) Stop bars used for runway incursion prevention will primarily be the uncontrolled type.
(a) For example, an uncontrolled stop bar may be installed on a high speed exit to a runway
that is never used for entering or crossing the runway in order to prevent aircraft from inadvertently entering the runway from that exit.
(b) Controlled and uncontrolled stop bars may also be installed during certain runway use
configurations or runway closures to prevent access to the runway.
(c) Stop bars may also be installed on runways (that are used as part of a taxiing route) at the
intersection with another runway. In this case the stop bar should be interlocked with any taxiway lighting installed on the runway so that the stop bar and taxiway lights will not be illuminated when the runway lights are illuminated. See Paragraph 2.1.2(c).
b. Complex Taxiway Configurations. Taxiway centerline lights should be installed to improve
guidance for complex taxiway configurations. Edge lights may be installed in addition to centerline lights if warranted by operational and weather conditions.
c. Apron Areas. Taxiway centerline lights should be installed in apron areas where other lighting
may cause confusion to taxiing or parking operations.
4.3. TAXIWAY CENTERLINE.
a. General. A taxiway centerline lighting system consists of unidirectional or bidirectional in-
pavement lights installed parallel to the centerline of the taxiway.
NOTE: If Airport Operators have difficulty applying the guidance in this AC, they should consult with their local FAA Airports Division for additional information.
b. Color-Coding. Taxiway centerline lights are green except as provided in the following
subparagraphs:
(1) Lead-off Lights. Taxiway centerline lights which provide visual guidance to persons exiting
the runway (lead-off lights) are color-coded to warn pilots and vehicle drivers that they are within the runway environment or instrument landing system/microwave landing system (ILS/MLS) critical area. Alternate green and yellow lights are installed from the runway centerline (beginning with a green light) to one centerline light position beyond the runway hold or ILS/MLS critical area hold position ending with a yellow light. The fixture inside the runway hold position must always be green when approached from the taxi direction and yellow when approached from the runway direction (bidirectional). If the layout of the lights results in an odd number of color-coded lights, the first two taxiway centerline lights on the runway should be green. See Figure 44, Detail A, for an example of a lead-off light configuration.
(2) Lead-on Lights. Lead-on lights provide visual guidance to pilots entering the runway. They
are also color-coded with the same yellow/green color pattern as lead-off lights to warn pilots and vehicle drivers that they are within the runway environment or ILS/MLS critical area. The color-coding begins with a green light at the runway centerline and progresses to one light
beyond the runway hold or ILS/MLS critical hold position. The fixture used prior to the runway hold or ILS/MLS critical area position must always be green when approached from the taxi direction and yellow when approached from the runway direction (bidirectional).
(3) Taxiway centerline lights that cross a runway are color-coded with a green light beginning at
the runway centerline and must end with a yellow light one centerline light position beyond the runway hold or ILS/MLS critical area holding position. See Figure 44, Detail B. If the layout of the lights results in an odd number of color-coded lights, the first two taxiway centerline lights on the runway should be green.
c. Longitudinal and Lateral Spacing. The lights are spaced longitudinally per Table 4-1 for
minimum authorized operations above and below 1,200 feet (365 m) RVR. Fixtures should be installed so that their nearest edge is approximately 2 feet (0.6 m) from any rigid pavement joint. Allow a tolerance for individual fixtures of ±10 percent of the longitudinal spacing specified to avoid undesirable spots. However, a tolerance of ±2 ft (0.6 m) is allowed for fixtures spaced at 12.5 ft (4 m). Displace centerline lights laterally a maximum of 2 feet (0.6 m) (to the nearest edge of the fixture) to avoid rigid pavement joints and to ease painting the centerline marking. Apply this lateral tolerance consistently to avoid abrupt and noticeable changes in guidance; i.e., no "zigzagging" from one side of the centerline to the other.
NOTE: Taxiway fillets are designed in relation to the centerline of the curve and, therefore, the location of the centerline marking. Displacement of taxiway centerline lights 2.5 feet (0.6 m) to the inside of a curve does not necessitate enlargement of the fillet.
Table 4-1. Longitudinal Dimensions.
Maximum Longitudinal Spacing 1,200 Feet (365 m) RVR and Above
Below 1,200 Feet (365
m) RVR Radius of Curved Centerlines 75 ft (23 m) to 399 ft (121 m) 25 ft (7.6 m) (2) 12.5 ft (4 m) 25 feet (7.6m) (1)
400 ft (122 m) to 1199 ft (364 m) 50 ft (15 m) 25 ft (7.6 m)
≥1200 ft (365 m) 100 ft (30 m) 50 ft (15 m) Acute-Angled Exits 50 ft (15 m) 50 ft (15 m) (See Figure 45 and AC 150/5300-13) Straight Segments 100 ft (30 m) (3) 50 ft (15 m)(3)
NOTES:
(1) A L-852K fixture may be used vice a L-852D. (2) A L-852J fixture may be used vice a L-852B. (3) Short straight taxiway segments may require shorter spacing per paragraphs 4.3.c and 4.3.h.
d. Acute-Angled Exits. For acute-angled exits, taxiway centerline lead-off lights begin 200 feet (61
m) prior to the point of curvature of the designated taxiway path, as shown in Figure 45. See Figure 45 additional details about requirements for light spacing and offsets. If the acute-angled exit is intended to be used only as an exit, then install unidirectional centerline light fixtures so that the lights can be only seen by the pilots of an exiting aircraft.
AC 150/5340-30D 9/30/2008
On existing systems: If a bidirectional fixture is used, we recommend blanks be installed in the opposite side of the lead-off fixture so that neither lead-on lights nor lights leading from the parallel taxiway to the holding position would be visible.
e. Taxiway/Runway Intersections Other Than Acute-Angled Exits. For these exits which lie on low
visibility taxi routes, taxiway centerline lead-off lights begin at the point of curvature on the runway if the runway has approach or departure minimums below 600 ft (183 m) RVR. Leadoff/lead-on lights are recommended below 1,200 ft (365 m) RVR. (Extra lead-off/lead-on lights should not be installed before the point of curvature on the runway because they would erode the visual distinction between acute-angled exits and other exits.) Taxiway centerline lead-on lights should extend to the PT on the runway, as shown in Figure 45, if the runway has departure minimums below 600 ft (183 m) RVR. Where operations are not conducted below 1,200 ft (365 m) RVR, neither taxiway centerline lead-on nor lead-off lights may be installed within the confines of the runway. Further, if the taxiway is perpendicular to and dead-ends into the runway, the taxiway centerline light nearest the runway must be installed 150 feet (46 m) from the centerline of the runway. Otherwise, taxiway centerline lights must not extend into the confines of the runway per Figure 43.
f. Taxiways Crossing a Runway. At airports where operations below 600 ft (183 m) RVR are
conducted, taxiway centerline lights (alternating yellow/green pattern per paragraph 4.3b(3)) should continue across a runway if they are installed on a designated low visibility taxi route. We recommend that centerline lights continue across a runway for operations below 1,200 ft (365 m) RVR where the taxiway is an often used route or there is a jog in the taxiway at the intersection with the runway. Otherwise, taxiway centerline lights must not extend onto the runway.
g. Taxiways Crossing Another Taxiway. Continue taxiway centerline lighting across the intersection
when a taxiway intersects and crosses another taxiway. If the fillets at a given taxiway intersection meet the design criteria of AC 150/5300-13 and the taxiway centerline markings follow the taxiway curves per AC 150/5340-1, then taxiway centerline lights must be installed as shown in Figure 47; otherwise, install them as shown in Figure 43. See paragraph 4.7a for criteria on the installation of taxiway intersection centerline lights and clearance bars.
h. Short Straight Taxiway Segments. There must be a minimum of four taxiway centerline lights
installed on short straight taxiway segments. See Table 4-1.
i. Orientation of Light Beam for Taxiway Centerline Lights. Taxiway centerline lights must be oriented as follows, with a horizontal tolerance of ±1 degree.
(1) On Straight Portions. On all straight portions of taxiway centerlines, the axis of the light beam
must be parallel to the centerline of the taxiing path.
(2) On Curved Portions (Excluding Acute-Angled Exits) with Standard Fillets. Orient the axes of
the two beams of bidirectional lights parallel to the tangent of the nearest point of the curve designated as the true centerline of the taxiway path. Orient the axis of a unidirectional light beam so that it is "toed-in" to intersect the centerline at a point approximately equal to four times the spacing of lights on the curved portion. Measure this chord spacing along the curve. See Figure 48.
(3) On Curved Portions (Excluding Acute-Angled Exits) with Non-Standard Fillets. See Figure
43 for orientation and configuration of bidirectional and unidirectional fixtures for taxiway intersections, taxiways crossing a taxiway or a runway, and taxiway curves.
(4) Acute-Angled Exits. Orient the axis of a unidirectional light beam so that it is "toed-in" to
intersect the centerline at a point approximately equal to four times the spacing of lights on the curved portion. Measure this chord spacing along the curve. Orient the axes of the two beams of bidirectional lights parallel to the tangent of the nearest point of the curve designated as the true centerline of the taxiing path.
j. Supplemental Taxiway Edge Lights and Elevated Edge Reflectors. Refer to AC 120-57 for criteria on supplementing taxiway centerline lights with taxiway edge lights (L-861T), or certified elevated edge reflectors (L-853) for low visibility operations. For higher visibilities (>600 RVR), where taxiway edge lights are not installed, taxiway centerline lighting should be supplemented with certified elevated edge reflectors installed adjacent to the taxiway edge on paved fillets and on curves of radii less than 800 feet (244 m) (measured to the taxiway centerline). Supplemental edge lights may be installed to aid taxi operations when centerline lights are obscured by snow. Space edge lights and reflectors per the requirements of Chapter 2. Supplemental reflectors may be used in ramp areas.
4.4. RUNWAY GUARD LIGHTS (RGLs).
a. General. Elevated and in-pavement RGLs serve the same purpose and are generally not both
installed at the same runway holding position. However, if snow could obscure in-pavement RGLs, or there is an acute angle between the holding position and the direction of approach to the holding position, it may be advantageous to supplement in-pavement RGLs with elevated RGLs. Each elevated RGL fixture consists of two alternately illuminated, unidirectional yellow lights. In-pavement RGLs consist of a row of alternately illuminated, unidirectional yellow lights.
b. Location of In-Pavement RGLs. In-pavement RGLs are centered on an imaginary line which is
parallel to, and 2 feet (0.6 m) from, the holding side of the runway holding position marking as shown in Figure 49. The lights may vary from this imaginary line up to ±2 inches (±50 mm) in a direction perpendicular to the holding position marking. Holding position marking locations are described in AC 150/5340-1. If a conflict with rigid pavement joints occurs, move both the runway holding position marking and the RGLs away from the runway the minimum distance required to resolve the conflict. If other markings (e.g., geographical position markings) are installed, they must be moved as well.
(1) Lateral Spacing - Preferred Method. The lights are spaced across the entire taxiway, including
fillets, holding bays, etc., at intervals of 9 feet, 10 inches (3 m), ±2 inches (±50 mm), centerto-center, as shown in Figure 49. The lights are spaced in relation to a reference fixture which is installed inline (longitudinally) with existing or planned taxiway centerline lights. However, it is not intended that the reference fixture replace a taxiway centerline light. If a conflict between the reference fixture and a centerline light occurs, the reference fixture takes the place of an existing centerline light and a new centerline light is installed per the criteria in paragraph 4.3.c. If the holding position marking is intersected by multiple taxiway centerline markings, the reference fixture is set at the centerline that is used most often. A fixture whose outboard edge falls at a point less than 2 feet (0.6 m) from the defined edge of the taxiway (outboard edge of the taxiway marking) may be omitted. Individual fixtures may be moved laterally a maximum of ±1 foot (305 mm) in order to avoid undesirable spots: i.e., conduit and rigid pavement joints, etc.
NOTE: If undesirable spots cannot be avoided in this way, fixtures may be moved no more than 2 feet (0.6 m) using the following alternate method.
AC 150/5340-30D 9/30/2008
(2) Lateral Spacing - Alternate Method. The following alternate method of spacing the lights
must be followed if it is not possible to meet the preferred method specified in paragraph 4.4.b(1). The lights are spaced across the entire taxiway, including fillets, holding bays, etc. If it is possible to meet paragraph 4.4.b(1) by allowing the reference fixture to be moved any amount laterally, then that method should be used. Otherwise, the lights must be spaced as uniformly as possible with a minimum spacing of 8 feet (2.4 m) and a maximum of 13 feet (4 m).
c. Light Beam Orientation for In-Pavement RGLs. The L-868 bases for in-pavement RGLs must be
installed such that a line through one pair of bolt holes on opposite sides of the base is parallel to the runway holding position marking. Each fixture is installed so that the light beam faces away from the runway and is perpendicular to the runway holding position marking within a tolerance of ±1 degree. For some pavement configurations, it may be necessary to orient the lights at some angle to the marking. To accomplish this, install a 12 bolt-hole base using the above procedure; this allows the light fixtures to be adjusted 30 degrees left or right, as required. See Figure 51 for a typical example.
d. Location of Elevated RGLs. Elevated RGLs are collocated with the runway holding position
marking and are normally installed on each side of the taxiway. The distance from the defined taxiway edge to the near side of an installed light fixture must be 10 to 17 feet (3 to 5 m). To avoid undesirable spots, the RGL may be moved up to 10 feet (3 m) farther from the runway, but may not be moved toward the runway (see Figure 50). If a stop bar is installed at the runway holding position, the elevated RGL must be located at least 3 feet, 6 inches (1 m) outboard of the elevated stop bar light. The RGL must not interfere with the readability of the runway holding position sign, obscure any taxiway edge lights, or interfere with other airport lighting.
e. Light Beam Orientation for Elevated RGLs. RGLs must be oriented to maximize the visibility of
the light to pilots of aircraft approaching the runway holding position. The orientation must be specified by the design engineer to aim the center of the light beam toward the aircraft cockpit when the aircraft is between 150 feet (45 m) and 200 feet (60 m) from the holding position, along the predominant taxi path to the holding position. The vertical aiming angle must be set between 5 degrees and 10 degrees above the horizontal. The designer must specify aiming of the lights such that the steady-burning intensity at all viewing positions between 150 feet (45 m) and 200 feet (60 m) from the holding position is at least 300 candela (cd) for an incandescent lamp when operated at the highest intensity step. (Refer to AC 150/5345-46 for specifications for the light intensity and beam spread of the L-804 RGL fixture.) If these criteria cannot be met for all taxi paths to the holding position, consider using multiple fixtures aimed to adequately cover the different taxi paths. Use in-pavement fixtures to increase the viewing coverage, or aim the single fixtures on each side of the holding position to optimize the illumination of the predominant taxi path.
4.5. RUNWAY STOP BAR.
a. General. A stop bar consists of a row of unidirectional in-pavement red lights and an elevated red
light on each side of the taxiway.
b. Location of In-Pavement Stop Bar Lights. In-pavement stop bar lights are centered on an
imaginary line which is parallel to, and 2 feet (0.6 m) from, the center of the fixture and the holding side of the runway holding position marking, as shown in Figure 50. The lights may vary from this imaginary line up to ±2 inches (±50 mm) in a direction perpendicular to the holding position marking. Holding position marking locations are described in AC 150/5340-1. If a conflict with rigid pavement joints occurs, move both the runway holding position marking and
the stop bar lights away from the runway the minimum distance required to resolve the conflict. If other markings (e.g., geographical position markings) are installed, they must be moved as well.
(1) Lateral Spacing - Preferred Method. The lights are spaced across the entire taxiway, including
fillets, holding bays, etc., at intervals of 9 feet, 10 inches (3 m), ±2 inches (±50 mm), centerto-center, as shown in Figure 50. The lights are spaced in relation to a reference fixture which is installed inline (longitudinally) with existing or planned taxiway centerline lights. However, it is not intended that the reference fixture replace a taxiway centerline light. If a conflict between the reference fixture and a centerline light occurs, the reference fixture takes the place of an existing centerline light and a new centerline light must be installed per the criteria in paragraph 4.3.c. If the holding position marking is intersected by multiple taxiway centerline markings, the reference fixture must be set at the centerline that is used most. If a fixture’s outboard edge falls at a point less than 2 feet (0.6 m) from the defined edge of the taxiway marking, the outboard edge of the taxiway marking may be omitted. Individual fixtures may be moved laterally a maximum of ±1 foot (305 mm) in order to avoid undesirable spots, e.g., conduit, etc.
NOTE: If undesirable spots cannot be avoided in this way, fixtures may be moved no more than 2 feet (0.6 m) using the following alternate method.
(2) Lateral Spacing - Alternate Method. This alternate method of spacing the lights should be
followed if it is not possible to meet the preferred method per paragraph 4.5b(1). The lights are spaced across the entire taxiway, including fillets, holding bays, etc. If it is possible to meet paragraph 4.5b(1) by allowing the reference fixture to be moved any amount laterally, then that method should be used. Otherwise, the lights should be spaced as uniformly as possible with a minimum spacing of 8 feet (2.4 m) and a maximum spacing of 13 feet (4 m).
c. Light Beam Orientation for In-Pavement Stop Bar Lights. The L-868 bases for in-pavement stop
bar lights must be installed such that a line through one pair of bolt holes on opposite sides of the base is parallel to the runway holding position marking. Each fixture is installed so that the axis of the light beam faces away from the runway and is perpendicular to the marking with a tolerance of ±1 degree. In some instances, it may be necessary to aim the lights at some angle to the marking. To accomplish this, install a 12 bolt-hole base using the above procedure. This allows the light fixtures to be adjusted 30 degrees left or right, as required. See Figure 51 for typical examples.
d. Location of Elevated Stop Bar Lights. Elevated stop bar lights are installed in line with the in-
pavement stop bar lights on each side of the taxiway. They are located not more than 10 feet (3 m) from the defined edge of the taxiway. For airports that perform any snow removal operations, if taxiway edge lights are present, the elevated stop bar light should not be installed closer to the taxiway edge than the line of taxiway edge lights. This is to help prevent the elevated stop bar light from being struck by snow removal equipment. In order to avoid conflicts with taxiway edge lights or undesirable spots, the elevated stop bar lights may be moved up to 10 feet (3 m) farther from the runway, but may not be moved toward the runway. See Figure 50.
e. Light Beam Orientation for Elevated Stop Bar Lights. Elevated stop bar lights should be oriented
to enhance conspicuity of the light by pilots of aircraft approaching the runway holding position. In general, the orientation must be specified by the design engineer to aim the axis of the light beam toward the aircraft cockpit when the aircraft is between 120 feet (37 m) and 170 feet (52 m) from the holding position, along the predominant taxi path to the holding position. The vertical aiming angle must be set between 5 degrees and 10 degrees above the horizontal. The designer
AC 150/5340-30D 9/30/2008
must specify aiming of the lights such that the axis of the light beams intersects the primary taxiway centerline between 120 feet (37 m) and 170 feet (52 m) from the holding position.
4.6. COMBINATION IN-PAVEMENT STOP BAR AND RGLS.
At the option of the airport, combination in-pavement stop bar and RGL lights may be installed in lieu of standard in-pavement stop bar fixtures. This option is provided to allow for the provision of in-pavement RGLs above 1,200 feet (365 m) RVR and a stop bar below 1,200 feet (365 m) RVR for a given location. (A typical application includes taxiways >150 feet (46 m) wide which lie on a designated low visibility taxi route for operations below 600 feet (183 m) RVR.) The circuit should be designed so that the yellow and red lights cannot both be "on" at the same time. Combination stop bar/RGL fixtures are installed in the same location and with the same light beam orientation as in-pavement stop bars. Refer to AC 120-57 for further criteria on the application of combination stop bar/RGLs below 1,200 feet (365 m) RVR.
4.7. CLEARANCE BAR CONFIGURATION.
a. General. A clearance bar consists of a row of three in-pavement yellow lights to indicate a low
visibility hold point. The fixtures are normally unidirectional but may be bidirectional depending upon whether the hold point is intended to be used in one or two directions. Refer to AC 120-57 for criteria on the application of clearance bars. In addition, with the following exceptions, clearance bars are installed (without regard to visibility) at a taxiway intersection with nonstandard fillets or where the taxiway centerline lights do not follow curves at intersections, as depicted in Figure 43. Clearance bars installed for this purpose consist of unidirectional fixtures.
(1) Clearance bars may be omitted if taxiway edge lights are installed at the intersection per
paragraph 2.1.3b(3).
(2) Clearance bars at a "T" or "+" shaped taxiway/taxiway intersection may be replaced, or
supplemented, by an omnidirectional yellow taxiway intersection light (L-852E or F, as appropriate) installed near the intersection of the centerline markings if the angle between the centerlines of any two adjacent segments of the pavement is 90 degrees ± 10 degrees.
(3) The clearance bar located on an exit taxiway may be omitted if it would be located before, or
within 200 feet (61 m) beyond, a runway holding position (as viewed while exiting the runway).
b. Location of a Clearance Bar Installed at a Low Visibility Hold Point. A low visibility hold point
consists of an intermediate holding position marking, a geographic position marking, and a clearance bar. However, hold points are not necessarily located at taxiway/taxiway intersections. In-pavement clearance bar lights are centered on an imaginary line which is parallel to, and 2 feet (0.6 m) from, the holding side of the taxiway/taxiway holding position marking, as shown in Figure 52. The lights may vary from this imaginary line up to ±2 inches (±50 mm) (perpendicular to the holding position marking). If a conflict occurs with rigid pavement joints or other undesirable spots, move the taxiway/taxiway holding position marking, geographic position marking, and the clearance bar longitudinally any amount necessary to resolve the conflict. However, if the hold point is located at a taxiway/taxiway intersection, the aforementioned items must all be moved away from the intersecting taxiway the minimum necessary to resolve the conflict. If a conflict occurs between the center fixture in the clearance bar and a centerline light, the center fixture takes the place of an existing centerline light, and a new centerline light must be installed per the criteria in paragraph 4.3c.
c. Location of a Clearance Bar Installed at a Taxiway Intersection. A clearance bar installed at a
taxiway intersection is located per the criteria in paragraph 4.7b if that location is established as a hold point and taxiway/taxiway holding position markings are present. Otherwise, the clearance bar must be located in the same manner as if the holding position marking were present. This allows room for the possible future installation of the marking.
NOTE: Taxiway/taxiway holding position marking locations are described in AC 150/5340-1.
(1) Lateral Spacing. The center light of the clearance bar is installed in line with existing or
planned taxiway centerline lights. The two remaining lights are installed outboard of the center fixture on 5 foot (1.5 m) intervals, center-to-center, as shown in Figure 43, Clearance Bar Detail. The outboard fixtures may be moved laterally a maximum of ±1 foot (305 mm) in order to avoid undesirable spots, e.g., conduit, etc.
d. Light Beam Orientation for Clearance Bars. The axis of the light beam for each fixture must be
parallel to the centerline of the designated taxiway path with a tolerance of ±1 degree.
4.8. DESIGN.
a. General. The installation of in-pavement L-868 light bases and conduit should be done, if
possible, while the pavement is under construction or when an overlay is made. Installation of light bases after paving is very costly and requires a lengthy shutdown of the taxiway or runway.
b. Layout. Develop a design drawing prior to construction that shows the dimensional layout of each
lighting system to be installed. Correlate this design with current airport drawings to utilize available ducts and utilities and to avoid conflict with existing or planned facilities. Do not exceed 40% conduit fill, as stated in the conduit fill tables of NFPA 70, NEC. Also, correlate this design with the type of existing equipment fed by the existing cable system to minimize the effects of EMI.
c. In-Pavement Light Fixtures and Electrical Cables. Design each in-pavement lighting system for
one of the conditions listed in Chapters 10 and 11.
d. General Circuit Design and Control Concept
(1) For Airports That Use RGLs and/or Stop bars to Prevent Runway Incursions in Visibility
Above 1200 RVR. Each of these systems should be on dedicated circuits (see paragraphs 4.8f(1)(a) and 4.8.g(3)(a)).
(2) For Airports With Operations Below 1,200 ft (365 m) RVR. As the weather deteriorates
below 1,200 ft (365 m) RVR, SMGCS procedures to be in effect and will activate the "below 1,200 ft RVR" system on the airport lighting control panel. All low visibility lighting systems necessary for below 1,200 ft (365 m) RVR operations will be turned on, as detailed in AC 120-57. We recommend turning off taxiway centerline lights and edge lights on taxiways that are not designated as low visibility taxi routes.
(3) For Airports With Operations Below 600 ft (183 m) RVR. See AC 120-57, Surface Movement
Guidance and Control System, paragraph 8b(2)a, for operations below 600 ft (183 m) RVR.
AC 150/5340-30D 9/30/2008
e. Taxiway Centerline Lighting and Clearance Bar Systems.
(1) Fixture Selection. L-852C (narrow beam), L-852D (wide beam), and L-852F
(omnidirectional) fixtures are installed on taxiways that are designated as low visibility taxi routes below 1,200 ft (365 m) RVR per AC 120-57. Where the RVR ≥1200 feet, L-852A (narrow beam), L-852B (wide beam), and L-852E (omnidirectional) taxiway centerline fixtures must be installed.
(2) The appropriate L-852B (RVR ≥ 1200 feet) or L-852D (RVR < 1200 feet) bidirectional fixture
must be installed at the intersections of taxiways with taxiways, taxiways with runways, and/or runways at single taxiway curves, and on all straight sections of taxiways off runways up to a distance of at least 400 ft (122 m). The appropriate L-852B or L-852D unidirectional fixture must be installed on curved sections of taxiways. Alternatively, an L-852J (RVR ≥ 1200 feet) or L-852K (RVR < 1200 feet) fixture may be used for curved sections of taxiways per Table 4-1. The appropriate L-852A or L-852C fixture must be installed on straight sections of taxiways (excluding straight sections of taxiways off runways to an intersection). See Figure 43, Figure 45, and Figure 47 for typical lighting configurations. Unidirectional L-852A or L- 852C fixtures are normally installed on acute-angled exits. However, bidirectional fixtures may be installed to provide guidance for emergency vehicles approaching the runway.
(3) Power Supply. Series circuits for clearance bars and taxiway centerline lighting systems
should be powered from an appropriately-sized L-828 or L-829, Class 1, Style 2 (5-step) (preferred) or Style 1 (3-step) CCR. Brightness control is achieved by varying the output current. Determine the appropriate size and number of regulators for a specific 6.6-ampere series lighting circuit by using the curves shown in Figure 53.
(4) Secondary Circuit Design for Taxiway Centerline Lights. Example design calculations for the
secondary circuit for taxiway centerline lights are shown in Figure 53. The example calculations assume four fixtures are installed on the secondary side of each isolation transformer. Other designs/configurations will require individual analysis. Manufacturers’ recommendations should be sought when sizing components.
(5) Circuit Design for Clearance Bars and Low Visibility Taxi Routes.
(a) Clearance bars. We recommend that clearance bars installed at low visibility hold points
have the capability of being switched "off" in visibilities above 1,200 ft (365 m) RVR. This can be accomplished through the use of local control devices or circuit selector switches. Other clearance bars must be "on" whenever the taxiway centerline lights are "on."
NOTE: If a clearance bar is installed for both purposes described in paragraph 4.7a, then it must be "on" whenever the taxiway centerline lights are "on."
(b) Taxiways Designated as Low Visibility Taxi Routes Below 1,200 ft (365 m) RVR. We
strongly recommend that new taxiway centerline lighting circuits be designed with consideration of the low visibility taxi routes designated in the airport’s SMGCS plan for operations below 1,200 ft (365 m) RVR and below 600 ft (183 m) RVR. It is advantageous for lights on a low visibility taxi route to be installed on a separate circuit from those that are not. Further, take care to account for the possibility of different low visibility routes above and below 600 ft (183 m) RVR. For example, an uncontrolled stop bar installed for operations below 600 ft (183 m) RVR will be turned on below 1,200 ft
(365 m) RVR. This, in effect, eliminates the possibility of that taxiway being considered as part of a low visibility taxi route below 1,200 ft (365 m) RVR. The alternative is to design the taxiway centerline and edge light circuits so that they may be turned off below 600 ft (183 m) RVR, thus eliminating the requirement for an uncontrolled stop bar.
(6) Taxiway Centerline Lighting and Clearance Bar Control Methods. Refer to Chapter 13 for
control methods.
(a) General. Where possible, use simple switching to energize and de-energize the circuits or
to control lamp brightness.
(b) Remote Control. Remote control systems are controlled from a panel located in the cab of
the ATCT or at some other location. Use the control panel recommended in AC 150/5345-3. This panel controls operating relays located in the vault, from which power is supplied to the taxiway centerline lighting regulators.
There are many methods of providing for the remote control of L-828/L-829 CCRs, L-847 circuit selector switches, etc. Such methods may include ground-to-ground radio control (see AC 150/5345-49), twisted shielded pair copper, and fiber optic control lines. Control signals may be digital or analog. The designer is responsible for ensuring that the control system is suitable and that EMI does not cause adverse effects in the lighting systems or subsystems.
Two common methods used to control CCRs and other equipment are described below. They may be used as a basis for the design of more complex control systems.
1. 120 Volts AC. Where the distance between the remote control panel and the vault is not great enough to cause excessive voltage drop (greater than 5%) in the control leads, use the standard control panel switches to operate the control relays directly. Operating relays supplying power to the taxiway centerline regulators must have coils rated for 120 volts AC. A No. 12 AWG control cable must be used to connect the control panel to the power supply equipment in the vault. Special pilot low burden auxiliary relays, having proper coil resistance to reduce control current, may be used to obtain additional separation distance with 120-volt AC control circuits. It may be advantageous to use these relays for expanding existing 120-volt AC control circuits. Figure 27 and Figure 28 illustrate typical applications of 120-volt AC control circuits.
2. 48 Volts DC. Where the distance between the control panel and the vault would cause an excessive control voltage drop, a low voltage (48-volt DC) control system must be used. In such a system, remote control panel switches activate sensitive pilot relays, such as those specified in AC 150/5345-13, which, in turn, control the regulator relays. Use an appropriately sized cable, of a type which is listed for direct earth burial, to connect the control panel to the pilot relays. The DC control system is adequate for up to 7,900 feet (2408 m) separation between control point and vault. For typical application details, see Figure 29, Figure 30 and AC 150/5345-3.
(7) Partitioning of Circuits for Traffic Control.
(a) General. The taxiway centerline lighting system may be sectionalized to delineate specific
routes for ground movements and to control traffic where such control is deemed necessary by consultation with the air traffic facility manager and airport sponsor. In
AC 150/5340-30D 9/30/2008
Continue reading ↓ 120 of 547 passages shown