AC 150/5300-4B Utility Airports - Air Access to National Transportation (Consolidated to include Changes 1-9)
Establishes design, operation, and maintenance standards for utility airports.
This document is cancelled. It may have been replaced. Check the official source before relying on it.
Text read by OCR from a scanned file (8 of 88 pages). Check the original, as some words may be misread.
'•
(
(
AC 150/5300-4R
DATE June 24, 1975 (Page revised 1/30/81 by CHG 5) ADVISORY CIRCULAR
DEPARniENT OF TRANSPORTATION
Federal Aviation Administration
Washington, D.C.
Sl,bject: UTILITY AIRPORTS--AIR ACCESS TO NATIONAL TRANSPORTATION
* 1. PURPOSE. This advisory circular establishes design, operation, and maintenance standards for utility airports.
DEPARniENT OF TRANSPORTATION
2, CANCELLATION. Advisory Circular 150/5300- 4A, Utility Airports--Air Access to National Transportation, dated November 1968, is cancelled,
~\.OJ~ C. LEONARD E. MUDD Acting Associat e Admini strator for Airports
Initiated by: AAS-100
*
For sale by the Superintendent ot Documents, U.S. Government Printing Office
Washington, D.C. 20402
(
c
•
..
(
2/24/83 AC 150/5300-48 CHG 6
CONTENTS
CHAPTER 1. INTRODUCTION
CHAPTER 1. INTRODUCTION
Paragraph Page
1 • 2. 3.
Figure
General • • • • • • • • • • • • Airport Standards • • • • • • • Definitions and Explanations of Terms •
• • • • 1 • 1 • • • 1
1-1 . Obstacle free zone (OFZ) for precision instrument runway ••• • • • • 2-6
CHAPTER 2. PRINCIPLES OF APPLICATION
CHAPTER 2. PRINCIPLES OF APPLICATION
Paragraph
4 . 5 . 6 . 7 .
Figure
Airport Role Airport Type Future Considerations • Other Considerations
• • • 3 • 3 • 4 • • 4
2-1. Examples of small airplanes accommodated by airport type ••••••• 5
CHAPTER 3 . WIND ANALYSlS AND RUNWAY ORIENTATION
Paragraph
8 . 9. 10.
Figure
General Crosswinds • • • • • • Orientation and coverage • • • •
CHAPTER 3 . WIND ANALYSlS AND RUNWAY ORIENTATION
. 7 • 7 • 7
3-1. Wind vector diagram • ••• ••••• • • ••••••••••••••• 9
CHAPTER 4. RUNWAY LENGTH REQUIREt-1ENTS AND CAPACITY
Paragraph
11 . 12. 13. 14. 15.
Primary Runway Length • • • • • • • Crosswind Runway Length • • • • • •
Development of Runway Length Curves Other Considerations • • • • • • Runway Capacity • • • • • • • • • •
CHAPTER 4. RUNWAY LENGTH REQUIREt-1ENTS AND CAPACITY
(Figures 4-1 and 4- 2) •
11 11 11 12 12
iii
*
AC 150/5300-4B CHG 8
CONTENTS (CONT ' D)
Figure
4- 1. Runway length curves • •••• •••••• • ••• •• • • 4- 2 . Runway length to accommodate airpl anes having a seating
configurat ion of 10 passengers seats or more ••• •
7/3/85
13
14
CHAPTER 5 . LAND CONSIDERATI ON 1 OBSTRUCTION RESTRICTION 1 AND AIRPORT HAZARD REMOVAL
CHAPTER 5 . LAND CONSIDERATI ON 1 OBSTRUCTION RESTRICTION 1 AND AIRPORT HAZARD REMOVAL
Paragraph
16. 17. 18. 19. 20. 21 . 22.
Figure
5-3 . 5- 4.
Airport Hazards … Reconunended Clearing … Zoning and Land Use Compatibility . land Acquisition … . Acquisiti on Procedures . . . . . . Futur e Expansion … Use of Land for Nonaeronautical Purposes
Minimum land requireme nt s • • • • • • • • Land acquisition for approach protection
. . . . . . . . . . . . . .
CHAPTER 6 . SI TE INVESTIGATION
CHAPTER 6 . SI TE INVESTIGATION
Paragraph
23. General 24. Government Regulations • • • •• •• •• 25 . Engineering Aspects of Site Inv estigation •
… … . . … … … . . . .
CHAPTER 7. DESIGN CRITERIA AND DIMENSIONAL STANDARDS
Paragraph
iv
26. 27 . 28 . 29. 30.
General • • • • • • • • Future Rol e Considerations • • • • • • Dimensi onal criteria • ••••••• • Typical Airport Layout
CHAPTER 7. DESIGN CRITERIA AND DIMENSIONAL STANDARDS
Runway a nd Runway Safet y Area Longi t udinal Grade 3 1. Line - of- Sight • • • • • • • ••••• 32. Typical cross Section ••••• • • •• 33 . Application of Di mensional Standar ds
. . . . . . . . . . . . . . . . . . . . .
. . . .
15 16 17 18 19 19 20
23 24
25 25 25
29 29 29 30 30 30 3 1 31
(
*
(
(
(
2/24/83 AC 150/5300-4B CHG 6
2/24/83 AC 150/5300-4B CHG 6
CHAPTER 8. TAXIWAYS, TURNAROUNDS, AND HOLDING APRONS
Paragraph
34. 35. 36. 37. 38. 39.
Figure
General • • • ••• Parallel Taxiways . Exit Taxiways ••• Hangar and Apron Access Turnarounds • • Holding Aprons
Taxiways
Typical runway and taxiway fillets Turnaround- -angular • • • • • • • Turnaround--circular • • • •
CHAPTER 8. TAXIWAYS, TURNAROUNDS, AND HOLDING APRONS
• • • • • • • • • • • • • • 3 9 … 39 . . . . . . 39 • • • • • • • • • • • • • 3 9 • • • • • • • • • • • • . • 3 9 . . • … 40
… 41 • • • • • • • • • • 4 2 • • 43 . • • • . • • • • • • • 4 4
8-1. 8-2. 8-3. 8-4. 8-5. Turnaround--rectangular • Holding apron . • • • • • •• 44-1
CHAPTER 9. AIRPLANE PARKING AND TIEOOWN
CHAPTER 9. AIRPLANE PARKING AND TIEOOWN
Paragraph
40. 41. 42. 43. 44.
Figure
9-1. 9-2. 9-3.
General •
Itinerant Apron for Tiedowns
Apron • • • • • Based Airplanes •
Other Considerations
Parking apron area • • • ••••••• Airplane itinerant operations •••••••. Tiedown layouts . • • • • • • • • • • • • • • •
CHAPTER 10. BUILDINGS AND HANGARS
Figure 9-1 · page 5Picture of the page from the copy saved here
CHAPTER 10. BUILDINGS AND HANGARS
Paragraph
45. General 46. Hangars . . • • • • • • • • • • • • • • • • • • 47 . Administration Building • • • • • • • •••• 48. Airport Survey • • • • • • • • • • • • • • 49. Building Plan • • • • . • • • • 50. Expansion . . … 51. Circulation • • • • • • ••• •••• 52. Waiting Room • • • • • • • • • • • 53. 54 .
• • • . . 45 • 45 • • • 46 • • 46 • • 46
• • 48 • • 49 • • 50
… 51
. • • • • 51
• 51 . 52 • 53 • • • 54 . . . 54
• • 54 • 55 … 55 55.
Manager's Office •••••••••••• ••. Eating Facilities • . •• •. Public Restrooms • • • • • • . . • • • 56 56. Roads and Auto Parking . . . • . • 56
v
AC 150/5300- 4B CHG 6 2/24/83
AC 150/5300- 4B CHG 6 2/24/83
Figure
10-1 . 10- 2. 10-3 . 10-4. 10- 5. 10-6 . 10-7 .
Parking apron area • • • ••• •••• . T- Hangar l ayout • • • • • • • • General aviation activity survey form • • • •••.• •• • General aviation space inventory form • • ••• Typical peak-hour passengers Schematic flow in an admini stration building • • •••• • Waiting area
CHAPTER 11. MARKI NG, LIGHTING, AND VISUAL AIDS
CHAPTER 11. MARKI NG, LIGHTING, AND VISUAL AIDS
• 58 • 59 • 60 • • • 61 … 62
• • 63 . • • • . • 64
Paragraph
57. 58. 59. 60. 61.
Figure
11- 1. 11- 2. 11-3. 11- 4. 11- 5.
General … … • • • • 65 Airport Marking • • • • • • • • • • • . • . . . 65 Airport Lighting • • • • • • • • • • • • • 66 Airport Visual Aids • • • • • • • • • • • • • • 67 Other Marking Practices • • • • • • • • • • • • • 68
Airport Typical Typical Typical Typical
marking … … • 69 a i rport lighting system • • • • • • • • • • • . . . • • . . 70 … 71 . . . . . . . 71 . • … 72
REIL installation • • • • • • • • •• ODALS installation • • • • • • • • • • MALSF and MALSR installation • • • • • • •
CHAPTER 12. AIRPORT PAVING
CHAPTER 12. AIRPORT PAVING
Paragraph
62 . 63. 64. 65. 66 . 67.
General Stage Constructi on Soil Investigation Pavement Thickness Soil Stabilization Aggregate-Turf
and Evaluation •
• • 73 • • • 73 • • • • • • • • • • • • 7 4 • • • • • • • • • • . . . • • • • 7 5 … 75
• • • 76
CHAPTER 13 . OPERATI ON, MAINTENANCE, AN!) ADMINISTRATION
CHAPTER 13 . OPERATI ON, MAINTENANCE, AN!) ADMINISTRATION
Paragraph
68 . 69 . 70. 71. 72. 73.
Who Will Operate the Airport •• • •• Will the Airport Show a Profit • •• . Airport Leases • • • • • • Airport Regulations • • • • • • • Airport Accounts . • • • • Progr arns for Airport Development, Operation, :: 'ld Maintenance
. • . . . . 79
• • 80 • 81 • • • • 83 • 84 • • • 85
(
(
(
(
2/24/83 AC 150/5300-48 CHG 6
Paragraph
74. 75. 76 . 77 . 78 . 79 . 80 . 81.
What Maintenance is Necessary • • • • • • • • • • • • • • • • • • Who Will Perform Maintenance • • • • • • • • • • • • • • • • • • • • • 86 . 87
87 What Will Maintenance Cost • • • • • • . Airport Safety • • • • • • • • • • • • • • • • . Airport Beautification . • • • • • • • . • • • • • • • •
• 88 . 88
89 90 Landscapi ng . • … • . . . • • • . Architecture •••••••••••• •• Cleanup Programs • • • • • • • • •
CHAPTER 14. AIRPORT LAYOUT PLANS
CHAPTER 14. AIRPORT LAYOUT PLANS
Paragraph
82 . 83 . 84.
Figure
General Metric Conversion •••••• Typical Airport Layout Plan •
• 90
• 91 • 92 • 94
14- 1. Airport layout plan • • • • • • • . • • • • • • • • • • • • • • • • • • 97
CHAPTER 15. CONSTRUCTION PLANS
Paragraph
85 . 86 . 87 .
CHAPTER 15. CONSTRUCTION PLANS
General • • • • • •• Typical Set of Plans
Metric Application
• • • • • • • 99 . • • • • • • 99 • • • • • • 100
APPENDIX 1. AIRPLANE DESIGN GROUP CONCEPT (1 page)
APPENDIX 2. PRELIMINARY ENGINEERING CHECKLIST FOR FIELD INVESTIGATION (5 pages)
APPENDIX 3. ANALYZING WIND DATA (7 pages)
APPENDIX 3. ANALYZING WIND DATA (7 pages)
Paragraph
1. 2. 3. 4. 5.
Objective • • • • • • Assembling Wind Data Analyzing Wind Data . Conclusions • • Presumptions
1 1 1 2 2
vii
AC 150/5300-4B CHG 6
Figure
1. 2. 3. 4. 5.
Typical environmental data service wind summary • • • • • Windrose blank showing direction and divisions Completed windrose using figure 1 data ••••• Windrose analysis • • • • • • • • • • • • • • • • Windrose analysis-- estimating area not included ••
Figure 1 · page 8Picture of the page from the copy saved here
APPENDIX 4. TYPICAT~ SET OF PLANS (23 pages)
APPENDIX 4. TYPICAT~ SET OF PLANS (23 pages)
Paragraph
2/24/83
3 4 5 6 7
1. Introduction to Use • Specifications • • • • • Size of Plans • • •
. . . . … 1 1 1 2. 3.
APPENDIX 5. Withdrawn--Change 3
APPENDIX 6. RUNWAY CLEAR ZONE DIMENSIONS (1 page)
APPENDIX 7. AIRPORT REFERENCE POINT (ARP) (3 pages)
APPENDIX 7. AIRPORT REFERENCE POINT (ARP) (3 pages)
(
Paragraph (
1. 2. 3.
Figure
1. 2.
Discussion • • • • • • • • Sample Computation Accuracy • • • • • •
Sampl e layout • • • • • • • • • • • • • • • • Sample computation--airport reference point •
APPENDIX 8. COMPASS CALIBRATION PAD (8 pages)
Paragraph
1. 2. 3 . 4. 5. 6.
Figure
viii
APPENDIX 8. COMPASS CALIBRATION PAD (8 pages)
1. 2. 3.
Purpose Background
Application • Design of Compass Calibration Pad • Location of Compass Calibration Pad • Construction of Compass Calibration Pad •
Marking layout and details of wheel block • Type I. Compass calibration pad Type II. Compass calibration pad •
1 1 1
2 3
1 1 1 2 3 4
6 7 8 (
(
9/23/83 AC 150/5300-48 CHG 7
APPENDIX 9. THRESHOLD SITING REQUIREMENTS (7 pages)
APPENDIX 9. THRESHOLD SITING REQUIREMENTS (7 pages)
Paragraph Page
1. 2. 3. 4. 5.
Figure
1. 2 . 3.
Purpose Application • Limitations • Evaluation Considerations • Locating, Displacing, or Relocating the Threshold •
Dimensional standards for locating thresholds • Approach slopes • • • . • • • • • • Approach slopes--offset localizer • • • • • •
APPENDIX 10. Withdrawn--change 6
APPENDIX 10. Withdrawn--change 6
1 1 1 1 2
5 6 7
APPENDIX 11. CURRENT AIRCRAFT ARRANGED BY AIRCRAFT MANUFACTURER, APPROACH SPEED,
AND WINGSPAN (11 pages)
APPENDIX 12. INDEX (15 pages)
ix
(
c
l
2/24/83 AC 150/5300-4B CHG 6
CHAPTER 1. INTRODUCTION
* 1. GENERAL. Section 103 of the Federal Aviation Act of 1958 states in part, "In the exercise and performance of his power and duties under this Act the Secretary of Transportation shall consider the following, among other things , as being in the
CHAPTER 1. INTRODUCTION
public interest: (a) The regulation of air commerce in such manner as to best promote its development and safety and fulfill the requirements of defense;
2.
(b) The promotion, encouragement, and development of civil aeronautics ••.• " This public charge to promote, encourage, and develop civil aeronautics carries with it the need to foster a national system of safe and efficient airports. The Federal Aviation Administration (FAA) presents the standards and recommendations in this publication to guide interested persons in the development of safe and efficient airport s .
AIRPORT STANDARDS. The standards, recommendations , and guidance material in this Advisory Circular (AC) define an airport suitable for the less demanding Aircraft Approach Category A and B airplanes, i. e . , airplanes with approach speeds of less than 121 knots. The other airports need to be designed and maintained to the standards and, to the extent physically feasible , to the recommendations in AC 150/5300-12, Airport Design Standards--Transport Airports, current edition. The FAA uses the standards and recommendations in this publication to provide technical guidance for the design of safe and efficient airports; and to evaluate both the effect of proposed construction, alteration, activation , and deactivation of airports on the national airport system and the effect of proposed construction and alteration of objects on air navigation. The standards and recommendations in this publication complement, but are not intended to take precedence over, aircraft operating rules and procedures.
a. Metric Units. Airport authorities may design their facilities in the metric system of units or in the U.S. customary system. In general, where additions or expansions are planned to an existing facility , such as a runway, taxiway, or apron , either system of units may be used. Where a new facility is to be built, the use of metric units is encouraged. Chapter 14 contains the policy for the use of and conversion to metric units.
* b. Technical Assistance. Technical assistance in the planning , design, construction, maintenance, and modernization of airports may be obtained
from state aviation officials, FAA airport engineers, and experienced engineering firms. AC 150/5000-3, Address List for Regional Airports Divisions and Airports District/Field Offices, current edition , contains the addresses for all FAA Regional Airport Divisions and Airports District/Field Offices.
3. DEFINITIONS AND EXPLANATIONS OF TERMS . The foll·, ling subparagraphs define the terms used in this publication:
Chap 1
Par 1 Page 1
*
*
*
AC 150/5300-4B CHG 8
AC 150/5300-4B CHG 8
I·
TORA TOOA ASOA LOA
TORA ASOA LOA I :
TORA TOOA
LOA
I ·I
I
CWY
TODA •I
I SWY I
ASOA ~
I .I
I 1.- TORA ~TOOA
ASDA
7/3/85
LOA ===I
Note . All declared distances are illustrated for operations from left to right
j. Displaced Threshold. A displaced threshold is a threshold located at a point on the runway other then at the runway end. Except for the approach standards defined in FAR Part 77, approach surfaces are associated with the threshold location.
I 1.- TORA ~TOOA
(
k. Hazard to Air Navigation. Any object which has a substantial adverse ( effect upon the safe and efficient use of navigable airspace by aircraft or on the operation of air navigation facilities is a hazard to air navigation.
In and of itself , an obstruction to air navigation may not be a hazard to air navigation, however, FAA presumes it to be and treats it as a hazard to air navigation until an FAA aeronautical study has determined it does not have a substantial adverse effect upon the safe and efficient use of navigable airspace by aircraft or on the operation of air navigation facilities. The FAA will conduct an aeronautical study of any object when the FAA deems a study is necessary to eliminate a specific presumption of hazard to air navigation. As part of the airport layout plan approval process, the FAA conducts aeronautical studies of all obstructions to air navigation identified on the airport layout plan. Hazards or potential hazards to air navigation are eliminated by either altering the existing or proposed object or adjusting the aviation operations to accommodate the object in
that order of priority.
1. Large Aircraft. A large aircraft is an aircraft of more than 12, 500 pounds (5 700 kg) maximum certificated takeoff weight.
m. Nonprecision Instrument Runway. A nonprecision instrument runway is one with an instrument approach procedure utilizing air navigation facilities, with only horizontal guidance , or area- type navigation equipment for which a straight- in nonprecision instrument approach procedure has been approved
or planned, and no precision approach facility or procedure is planned or * indicated on an FAA or DOD approved airport layout plan, or on other FAA or (_ DOD planning documents.
Chap 1
Par 3
c
*
(
7/3/85 AC 150/5300-4B CHG 8
7/3/85 AC 150/5300-4B CHG 8
n. Obstacle Free Zone (OFZ). An OFZ is an area:
Chap 1 Par 3
(1) Comprised of the runway OFZ, the approach OFZ, and the innertransitional surface OFZ.
(a) Runway OFZ. The runway OFZ is the volume of space above a surface longitudinally centered on the runway. The elevation of any point on the surface is the same as the elevation of the nearest point on the runway centerline. The runway OFZ extends 200 feet (60 m) beyond each end of the runway and its width is:
120 feet (36 m) for visual runways serving or expected to serve only small airplanes with approach speeds less than
50 knots.
2 250 feet (75 m) for nonprec1s1on instrument and visual runways serving or expected to serve small airplanes with approach speeds of 50 knots or more and no large airplanes.
3 300 feet (90 m) for precision instrument runways serving or expected to serve only small airplanes. (See figure 1-1.)
4 180 feet (54 m), plus the wingspan of the most demanding airplane, plus 20 feet (6 m) per 1,000 feet (300m) of airport
elevation~ or, 400 feet (120m), whichever is greater, for runways serving or expected to serve large airplanes. (See figure 1-1.)
(b) Approach OFZ. The approach OFZ is the volume of space above a surface which has the same width as the runway OFZ and rises at a slope of 50 (horizontal) to 1 (vertical) away from the runway into the approach area. It begins 200 feet (60 m) from the runway threshold at the same elevation as the runway threshold and it extends 200 feet (60 m) beyond the last light unit in the approach lighting system. The approach OFZ applies only to runways with an approach lighting system. (See figure 1-1.)
(c) Inner-Transitional SUrface OFZ. The inner-transitional surface OFZ is the volume of space above the surfaces which slope 3
(horizontal) to 1 (vertical) laterally from the edges of the runway OFZ and approach OFZ and end at the height of 150 feet (45 m) above the established airport elevation. The inner-transitional surface OFZ applies only to precision instrument runways. (See figure 1-1.)
(2) Free of all fixed objects. FAA approved frangible equipment which provides an essential aviation service may be located in the OFZ, provided the amount of penetration is kept to a practical mimimum. *
{3) Clear of vehicles as well as parked, holding, or taxiing aircraft in the proximity of an airplane conducting an approach, missed approach, landing, takeoff, or departure.
*
*
AC 150/5300- 4B CHG 8 7/3/85
AC 150/5300- 4B CHG 8 7/3/85
o . Obstruction to Air Navigation. An existing object, including a mobile object, is, and a future object would be, an obstruction to air navigation if it is of a greater height than any of the heights or surfaces defined in FAR 77 . 23 .
p . Precision Instrument Runway . A prec1s1on instrument runway is one with an instrument approach procedure utilizing an instrument landing system (ILS), microwave landing system (MLS), or precision approach radar (PAR) . A planned precision instrument runway is one for which a precision approach
system or procedure is indicated on an FAA or DOD approved airport layout plan, or on other FAA or DOD planning documents .
q. Relocated Threshold. A relocated threshold is a permanent threshold located at the relocated runway end.
r . Runway. A runway is a defined rectangular area on an airport prepared for the landing or takeoff of airplanes .
s . Runway Clear Zone . A runway clear zone is a trapezoidal area at ground level, under the control of the airport authorities, for the purpose of protecting the safety of approaches and keeping the area clear of the congregation of people. The runway clear zone begins at the end of each primary surface and is centered upon the extended runway centerline. See appendix 6 for runway clear zone standard dimensions .
(
*
t . Runway Safety Area. A runway safety area is a rectangular area, centered on the runway centerline, which includes the runway (and stopway, if ( present) and the runway shoulders . The portion abutting the edge of Zbe runway shoulders, runway ends, and stopways is cleared, drained, graded, and usually turfed . Under normal conditions, the runway safety area is capable of supporting snow removal, firefighting, and rescue equipment and accommodating the occasional passage of aircraft without causing major damage to the aircraft.
u . Small Aircraft . A small a ircraft is an aircraft of 12, 500 pounds (5 700 kg) or less maximum certificated takeoff weight.
v . STOL Aircraft. A STOL aircraft is an aircraft with a certified performance capabilty to execute approaches along a glide slope of 6 degree or steeper and to execute missed approaches at a climb gradient sufficient to clear a
15:1 missed approach surface at sea level . The gradient is based on the airport elevation and decreases at the rate of 5 percent per 1,000 feet
(300m), i .e., for an airport at 4,000 feet (1 200m) above mean sea level (MSL}, the gradient of the missed approach surface would be 18:1, 120 percent of 15:1 .
w.
STOL Runway . A STOL runway is one which is specifically designated and marked for STOL aircraft operations . Except for the standards for locating thresholds, specified in appendix 9, and for marking and lighting, STOL runways are designed and maintained to the standards and recommendations applicable to conventional takeoff and landing airplanes.
Chap 1
Par 3
* (
(
*
(
7/3/85 AC 150/5300-4B CHG 8
7/3/85 AC 150/5300-4B CHG 8
x. Stop End of Runway. The stop end of runway is the far runway end as viewed from the cockpit of a landing airplane .
y. Stopway. A stopway is an area beyond the stop end of the takeoff runway which is no less wide than the runway and is centered on the extended centerline of the runway . It is able to support an airplane during an aborted takeoff without causing structural damage to the airplane, and designated by the airport authorities for use in decelerating the airplane during an aborted takeoff.
z . Taxilane . A taxilane is the portion of the aircraft parking area used for access between taxiways, aircraft parking positions, hangars, storage
fa~iliti es , etc. A taxilane is outside the movement area.
aa. Taxiway. A taxiway is a defined ~ath, from one part of an airport to another , selected or prepared for the taxiing of aircraft.
bb. Taxiway Safety Area . A taxiway safety area is an area centered on the taxiway centerline, which includes the taxiway and taxiway shoulders . The portion abutting the edge of the taxiway shoulders is cleared, drained, graded, and usually turfed . Under normal conditions, the taxiway safety area is capable of supporting snow removal, fire fighting, and rescue equipment and accommodating the occasional passage of aircraft without causing major damage to the aircraft.
cc. Threshold. ·l'he threshold is the beginning of that portion of the runway available and suitable for the landing of airplanes .
dd. Transport Airport. A transport airport is an airport designed, constructed, and maintained to serve airplanes in Aircraft Approach Category C and D.
ee. Utility Airport . and maintained to
For discussion on
A utility airport is an airport designed, constructed, serve airpianes in Aircraft Approach Category A and B. airport type, see paragraph 5 .
ff . Visual Runway . A visual runway is a runway intended solely for the operation of aircraft using visual approach procedures, with no straight-in instrument approach procedure and no instrument designation indicated on an
FAA or DOD approved airport layout plan, or , on other FAA or DOD planning documents .
gg. Wind Coverage. Wind coverage is the percent of time for which aeronautical operations are considered safe due to acceptable crosswind components .
Chap 1 Par 3 Page 2-5
*
AC 150/5300-48 CHG 6 2/24/83
300' (90 m) (SEE NOTE)
(45 m} ABOVE AIRPORT ELEVATION
(45 m} ABOVE AIRPORT ELEVATION
RUNWAY OFZ
RUNWAY
PRIMARY SURFACE
NOTE:
50:1 APPROACH OFZ
RUNWAY CLEAR ZONE
THE RUNWAY· OFZ AND APPROACH OFZ WIDTH FOR RUNWAYS EXPECTED TO SERVE LARGE AIRCRAFT, IS 180 FEET (54 m), PLUS THE WINGSPAN OF THE MOST DEMANDING AIR- PLANE, PLUS 20 FEET (6 m) PER 1,000 FEET (300 ro} OF AIRPORT ELEVATION, OR 400 FEET (120m), WHICHEVER IS GREATER.
SECTION ALONG RUNWAY
SECTION ALONG RUNWAY
FIGURE 1-l. OBSTACLE FREE ZONE (OFZ) FOR PRECISION INSTRUMENT RUNWAY
Page 2-6 Chap l
(
(
(
*
*
(
9/23/83 AC 150/5300-4B CHG 7
CHAPTER 2. PRINCIPLES OF APPLICATION
4. AIRPORT ROLE. An airport may serve primarily a community and secondarily a nearby recreational area; or, it may serve mainly as a feeder stop for air taxi operations enroute to a regional air carrier airport. In certain cases its role may be to provide access to the airways from a relatively remote community.
CHAPTER 2. PRINCIPLES OF APPLICATION
a. Prior to the development of precision instrument runway standards for utility airports, the role of a utility airport was limited to those activities performed by small aircraft on nonprecision instrument and visual runways. *
b. With deregulation of the airlines and an increase in commuter operations, the FAA and the aviation industry recognized that standards for precision instrument runways at utility airports were both needed and feasible. Airport design standards based exclusively on the requirements of small * aircraft were subsequently developed for utility airports having an expanded
role of providing for all-weather operations. These standards were less demanding than the precision instrument runway standards for transport airports, in terms of real estate and clearing required. These standards were adopted with full recognition that the resulting more economical preci-
sion instrument facilities could also safely accommodate larger aircraft with approach speeds up to 120 knots.
c. Recognizing the need to reduce overall airport development cost, the FAA and the aviation industry also developed the airplane design group concept which links airport requirements to using aircraft. (See paragraph 3.)
d. To preserve the traditional roles of existing airports, however, Design Group I is subdivided into two groups, distinguishable by aircraft weight. The first includes just small aircraft or the family of aircraft expected at utility airports built to design standards prior to January 30, 1981. The second expands the service coverage to accommodate a limited number of
larger aircraft.
5. AIRPORT TYPE. Runway length separates utility airports into basic and general utility types. The small airplanes, commonly used for personal and business flying and for commuter and air taxi operations, which are served by Basic Utility and General Utility--Stage I airports are shown in figure 2-1. These airports can be expected to have the following kinds of activity:
a. Basic Utility--Stage I. This type of airport serves about 75 percent of the single-engine and small twin-engine airplanes used for personal and business purposes. Precision approach operations are not usually anticipated. This airport is designed for small airplanes in Airplane Design Group I.
b. Basic Utility--Stage II. This type of airport serves all the airplanes of Stage I, plus some small business and air taxi-type twin-engine airplanes.
Precision approach operations are not usually anticipated. This airport is also designed for small airplanes in Airplane Design Group I.
Chap 2 Par 4 Page 3
AC 150/5300-4B CHG 7 9/23/83
AC 150/5300-4B CHG 7 9/23/83
c. General Utility--Stage I. This type of airport serves all small airplanes. ( Precision approach operations are not usually anticipated. This airport is also designed for small airplanes in Airplane Design Group I.
d. General Utility--Stage II. This type of airport serves large airplanes in Aircraft Approach Category A and B and usually has the capability for preci-
sion approach operations. This airport is normally designed for airplanes * of Airplane Design Groups I and II. It may also be designed to serve Aircraft Approach Category A large airplanes in Airplane Design Group III. While runways serving or expected to serve large airplanes may be built to utility airport standards, they are considered as other than utility r unways
in aeronautical studies. *
*
6. FUTURE CONSIDERATIONS.
a. One factor for future consideration in the utility type airport is the probable requirement to operate during periods when the weather is below the minimums authorized for visual flight rules (VFR) . The requirement for this capability is highest among airplanes used for commuter, business, and air
taxi purposes.
b . The criteria contained in this publication provide the potential capability for the development of instrument runways . Air navigational aids (NAVAIDs) , such as instrument landing systems (ILS) , microwave landing systems (MLS), very high frequency omnidirectional radio ranges (VOR) , or nondirectional radio beacons (NDB) , are needed in order to take advantage of this potential. AC 150/5300-2, Airport Design Standards--Site Requirements for ( Terminal Navigational Facilities , current edition, describes in general
terms the land area, grading requirements, and operational clearances
7.
desired for NAVAIDs and air traffic control (ATC) facilities.
c. If the ultimate development plans include expansion of the airport to serve
airplanes in Aircraft Approach Category A with wingspans greater than 118 feet (36 m), or airplanes in Aircraft Approach Category B with wingspans greater than 79 feet (24m), or airplanes with approach speed greater than
120 knots , the airport should be designed to the criteria in AC 150/5300-12.
OTHER CONSIDERATIONS. A properly planned and designed utility airport is a definite asset to a community. Although the single event noise levels generated by aircraft using utility airports may not be as high as those at transport airports, the cumulative effect of a large number of operations may have an equivalent or greater overall noise impact than a transport airport with fewer operations. Therefore, it is important that airport planners locate the proposed utility airport in an area that is compatible with adjacent communities and will remain compatible in the future as a result of land use controls. It
is also important that airport planners inform local residents, as early in the airport development process as possible, of the proposed location of the airport, the scope of the airport operation, the measures which will be under-
taken to minimize noise, and of the value of the airport to their communities. Failure to do this can result in public sentiment turning against the airport and the imposition of severe operational limitations on it. (See paragraph 25 for further discussion of airport-community compatibility.)
Chap 2
Par 5
*
,.--
() ::r Ql '0
N
....,
H G) ~ ~
N
I I-' .
trJ
~ 1:"' trJ (f.l
0 ....,
(f.l
~ 1:"'
)>I H
~ 1:"' ~ trJ (f.l
)>' () () 0
~ 0 ~ trJ 0
0':1 ~
)>' H ~
10 0 ~ Ql ...a 8 Cl) ~ 1.11 trJ
~ Ql
~ 0..
0'1
Beech Beech
Bellanca Bellanca Bellanca
Cessna Cessna Cessna Cessna
BASIC UTILITY
BASIC UTILITY
STAGE I
Bl9 Sport/150 B24R Sierra/200
Citabria Series 8GCBC Scout 300A Super Viking
150 Series 172 Skyhawk 182 Skylane T206 Stationair
Grumman American AA-lB Trainer Grumman American AA- 5A Cheetah Grumman American AA-5B Tiger
Mooney M20C Ranger MOoney M20E Chaparral MOoney M20F Executive
STAGE I
Navion Rangemaster H
Piper PA- ll thru PA- 22 Series Piper PA- 28 Series Piper PA- 32-300 Cherokee Six Piper PA- 32-300R Lance
Rockwell Int' l . Rockwell Int' 1. Rockwell Int' l .
112 A Commander 112 TC Commander 114 Connnander
~
BASIC UTILITY
STAGE II
Beech Beech Beech Beech Beech
STAGE II
Cessna Cessna Cessna Cessna
Piper
Piper Piper
F33A Bonanza V35B Bonanza A36 Bonanza C23 Sundowner B55 Baron
204 Skywagon 337 Skymaster P337 Skymaster 310
P~32-260 Cherokee Six PA-23-250 Aztec PA- 34-200 Senaca II
Ted Smith Aerostar 600 Ted Smith Aerostar 601
Also accommodated are the
airplane models listed under Basic Utility Stage I .
Beech Beech Beech Beech Beech
Cessna Cessna
Pioer Piper Piper Piper
GENERAL UTILITY
GENERAL UTILITY
STAGE I
B58P Baron B6o Duke B8o Queen Air
E90 King Air B99 Airliner
340A 402B Businessliner
PA- 24 Series
-----...
PA-30- 150 Twin Commanche PA- 31- 350 Chi~ftain PA- 31-425 Navajo
Rockwell Int'l. 500S Shrike Rockwell Int' l . 685 Commander
Also accommodated are the airplane models listed under Basic Utility
STAGE I
Stages I and II .
Note : Some of the above airplane models have an option for a seating configuration of 10 passenger seats or more. See Figure 4-2 for additional listing of airPlane models.
The recommended runway length required to accommodate all the airplanes grouped under a specific airport type is obtainable from Figure 4- l .
N - tv ~ - 00 w
~
I-' 1.11 0 …
1.11 w 0 0 I .,.. 0':1 g
G)
0'1
(
c
(
6/24/75 AC 150/5300-4B
CHAPTER 3. WIND ANALYSIS AND RUNWAY ORIENTATION
CHAPTER 3. WIND ANALYSIS AND RUNWAY ORIENTATION
8. GENERAL.
a. The configuration of the airport is determined by the number and orientation of the runways. One of the primary factors influencing runway orientation is wind. Ideally the runway should be aligned with the prevailing winds. Wind conditions affect all airplanes, the smallest to the largest, in varying degrees. Generally, the smaller the airplane, the more it is affected by wind, particularly crosswind components. Crosswinds are often a contributing factor in small airplane accidents. In some cases, construction of two runways may be necessary to give the desired wind coverage.
b. Airport planners and designers should, therefore, make an accurate analysis of wind to determine the orientation and number of runways. The proper application of the results of this analysis will add
substantially to the safety and usefulness of the ai~port. Appendix 3 provides information on wind data for the purpose of airport planning and design, and the following paragraphs give ~rocedures in its
application to runway orientation concepts.
9. CROSSWINDS.
a. A crosswind component of wind direction and velocity is the resultant vector which acts at a right angle to the runway. It is equal to the wind speed multiplied by the trigonometric sine of the angle between
the wind direction and the runway direction. Normally, these wind vector triangles are solved graphically. An example is shown in Figure 3-1 . From this diagram, one can also ascertain the headwind and tailwind component of combinations of wind velocities and directions.
b. Study and analysis of different combinations of velocities and directions, having an 11 .4-mi1e-per-hour (mph) (9 . 9 knots) crosswind component, have found that different combinations produce similar adverse effects on the control handling characteristics of airplanes . Considering this and the method of repo~ting wind data, the 12-mph Qr 10.5-knot speed was selec~ed as a reasonable and convenient figure upon which to base runway orientation.
1~. ORIENTATION AND COVERAGE. The most desirable runway orientation based on wind is the one which has the largest wind coverage and minimum crosswind components .
Chap 3 Par 8 Page 7
AC 150/5300-4B 6/24/75
a. Wind coverage is that percent of time for which operations are con- ( sidered safe due to acceptable crosswind components. The desirable wind coverage for an airport is 95 percent,based on the total hours of weather observations. At some locations, the daily time period for weather observations is less than 24 hours; i.e., 16 hours. In any event, the data collected must be applied with an understanding of the objective; i . e., to attain 95-?ercent usability. At many airports, airplane operations are almost nil after dark. Accordingly, it may be desirable to analyze the wind data on less
than a 24-hour observation period. Also, at resort airports, where operations are predominantly seasonal, regard should be given to
the wind data for the predominant-use period.
b. Where a single runway cannot be oriented to provide 95-percent coverage, one or more additional runways will be required to raise
the coverage to that value.
c . The acceptable coverage value of 95 percent was selected after con-
sideration of various factors influencing operations to and from airports and the economics of providing the coverage. In any airport operation, there are periods when factors other than wind determine when a runway may be used. Low ceilings, reduced visibility, periods of runway maintenance, etc,, may preclude use of a particular runway even though existing wind conditions are favorable.
d. Appendix 3, Weather Data Source and Analysis, states in detail how a standard wind rose is compiled and used.
Chap 3 Page 8 Par 10
(
(
(
(
(
6/24/75
HEADWIND COMPONENT
HEADWIND COMPONENT
-KOOTS
'
TAILWIND COMPONENT
-KNOTS
Chap 3
1
~ … - -1.-\-- T 0 ""'"-- 90° CROSSWIND ~OJ:-- 20 30 40 SO COMPONENT
l---+1~~i:'J' … N i---_ -KNOTS
~ \~~~::/ … r---N~
10 T \ \" ~/""" /r-- … II _I I \ 1\."' / "' … '''f .... }..J 10 0
-20 \ Yr~ "y"'~l 1 " -i,l...-lE-XAM__,JPLE :
TAILWIND COMPONENT
\ \ \ "\. '? "'-. j
1<~oj Wind speed 20 ~ . " 1" knots. Angle between , /""\ ""'- u.e>/V;.: v runway and direction 30 +----f~ … --B~r--+--J\-1---= '\~'}~-~-1°~
0 ,---JL---1.- of wind -60°. Crosswind \ \/
~~ I component - 17 knots. · ~Oo <::> Headwind component - - 'i ~c, -+----- \._/ ~ ¢~" 10 knots.
40 -6--+-¥=!- '\-...\1. - Oo ~ ,
,_. '::& ~Oo c:~:~.~~"Y 1--- ~ - 00 ('\ ? +---1--4---+-~f---..J 0 I \ .Y -~ .• :~\V --~\)~ so ~--+--=~~~ov.: -r--+--1---+--~--+---+-~
I
FIGURE 3-1. WIND VECTOR DIAGRAM
FIGURE 3-1. WIND VECTOR DIAGRAM
Page 9 (and 10 ~.
(
(
9/23/83 AC 150/5300-48 CHG 7
CHAPTER 4. RUNWAY LENGTH REQUIREMENTS AND CAPACITY
* 11. PRIMARY RUNWAY LENGTH. Airplane flight manuals (supplemented with user operating data), AC 150/5300-12, and the runway length curves in this chapter provide guidance on the runway lengths needed to accommodate the airplanes expected to use a utility airport.
CHAPTER 4. RUNWAY LENGTH REQUIREMENTS AND CAPACITY
a. A runway length of at least 300 feet (90 m) is recommended to serve small airplanes with approach speeds less than 30 knots. The runway length is based on the airport elevation and increases at the rate of 30 feet (9 m) per 1,000 feet (300 m) of airport elevation above mean sea level (MSL).
b. A runway length of at least 800 feet (240 m) is recommended to serve small airplanes with approach speeds less than 50 knots. The runway length is based on the airport elevation and increases at the rate of 80 feet (24 m) per 1,000 feet (300 m) of airport elevation above mean sea level (MSL).
c. Figure 4-1 presents curves for determining the runway length to serve small airplanes with approach speeds of 50 knots or more, which accommodate less *
than 10 passengers. The recommended minimum runway length is the length for the airport elevation and the mean daily maximum temperature of the hottest month at the airport.
d. Figure 4-2 presents curves for the runway length to serve small airplanes, which accommodate 10 or more passengers, or small turbojet airplanes.
e. AC 150/5300-12 should be used if the runway is expected to serve large airplanes.
12. CROSSWIND RUNWAY LENGTH. At some airport sites, it is not feasible to obtain 95 percent wind coverage with one runway. In such cases, it may be determined that the benefits from a crosswind (or secondary) runway will justify its construction. Accordingly, the question arises: How long should the crosswind runway be? Where feasible, it should be at least 80 percent of the length recommended for the primary runway.
13. DEVELOPMENT OF RUNWAY LENGTH CURVES (FIGURES 4-1 AND 4-2).
a. Federal Aviation Regulations, Part 23, Airworthiness Standards: Normal, Utility, and Acrobatic Category Airplanes, prescribes airworthiness standards for the issuance of small-airplane type certificates. The individual airplane flight manual contains the performance information for each airplane (defined in Section 23.51, Takeoff; Section 23.75, Landing; and, Section 23.1587, Performance Information). This information is provided to assist the airplane operator in determining the necessary runway length for
safe operations.
b. Performance information from airplane flight manuals has been selectively
grouped and used to develop the runway length curves in figures 4-1 and
4-2. The major parameters used in developing these curves are the landing and takeoff distances for figure 4-1 and the landing, takeoff, and accelerate-stop distances for figure 4-2. The following conditions have been assumed in developing the curves:
Chap 4 Par 11 Page 11
*
AC 150/5300- 48 CHG 7
(1) zero headwindJ
(2) maximum certificated takeoff and landing weights; and
(3) optimum flap setting for the shortest runway length (normal operation) •
9/23/83
c. Other factors , such as relative humidity and runway gradient, have a
limited effect on runway length. For small airplanes , these factors are negligible and thus are not used in computing runway length for small airplanes.
14 . OTHER CONSIDERATIONS. In most cases , figures 4- 1 and 4- 2, AC 150/5300-12 , and airplane flight manuals should be used for determining the runway length at a utility airport. However, the airport planner should consider the following conditions which also could affect the runway length for a particular airport:
a. While figure 4-1 presents runway lengths for elevations up to 9 , 000 feet
(2 743 m) , some of the airplanes listed in the example grouping in figure 2- 1 are not capable of operating at high altitudes without modification. Therefore, special care must be exercised in adapting these curves to the critical airplane or group of airplanes for operations at elevations higher than 5, 000 feet (1 524 m) .
b . FAR Part 135 imposes the following conditions:
(
(1) For airplanes with a seating configuration of 10 passenger seats or more, the accelerate-stop distance must be considered in computing the ( required runway length. Figure 4-2 presents runway lengths con-
15 .
sidering accelerate-stop distance.
(2) The operators of small airplanes certificated prior to July 19, 1970, and having a seating configuration of 10 passenger seats or more, are permitted to use an overrun distance equal to that required to stop the airplane from a ground speed of 35 knots (40 miles per hour) in computing their accelerate- stop distance. This provision of FAR Part 135 may be met by providing a full length runway safety area beyond the runway end.
c. The runway length obtai ned from the airplane flight manuals may be used in
l i eu of the runway length curves depicted in figures 4-1 and 4-2 and AC 150/5300-12.
RUNWAY CAPACITY . The capacity of a runway is defined as the number of operations that the runway can accommodate in a limited time--usually 1 hour . An operation is defined as either a landing or a takeoff, therefore, a touch and go counts as two operations. AC 150/5060-5 , Airport Capacity and Delay, current edition , expl ains how to compute airport capacity and aircraft delays.
Page 12
Chap 4 Par 13
*
2/24/83
(
(
Chap 4
AC 150/5300-4B CHG 6
AC 150/5300-4B CHG 6
AIRPORT tLEVATION (FEET)
EXAMP LE: TEMP ERATURE S9"F AIR PO RT ELEVATION SL -
~~ IWNW AY LENGTH: - I - BAS IC STAGE I 2200' : 8 8 BAS IC STAGE II 2700' GE N. UTILITY 3200' ~ ~
~ ~ ~ ~
~ ~
~ ~
~ ~ ~ ~
~
~J:J
~C) f:'Jt;:) ~C) "C)
f:'J t::lcsf
f:'Jt;:) ~/
~p II' lcfSJ '>C) " ~ ~r;:,t::l""
EXAMP LE: TEMP ERATURE S9"F AIR PO RT ELEVATION SL -
">C) .I"
~~~~~
.1"
!:)() ">~ !:) ~~ '),C)~ ; "> .... ~
~~
A L.l1 !:) ...1' , … ()~ ··'),~~ ""
y
.~ ~4,; ·~()() ~~ lljY /r;:,()f;) ..., v ~ '\:~
1/'),_~r;:, ~ … '1 lA"
… ()~
~·
50 75 100 50 75 100 50 75 100
MEAN DAILY MAXIMUM TEMPERATURE ("F), HOTTEST MONTH OF YEAR
BASIC UTILITY
STAGE I
BASIC UTILITY
BASIC UTILITY
STAGE II
GENERAL UTn.ITY
STAGE 1
FIGURE 4-1. RUNWAY LENGTH CURVES
10000
9000
8000
7000
…
!-< 1:1:1 Ill "" '-.J'
6000 i5 ~ ~
~ ~ :::::> ex: 5000
4000
3000
2000
AC 150/5300-4B CHG 6
REPRESENTATIVE AIRPLANES
Beech Beech Beech Beech
B80 E90 B99 AlOO
Queen Air King Air Airl iner King Air
REPRESENTATIVE AIRPLANES
Britten-Norman Mark III-I Trilander
Mitsubishi
Swearigen Swearigen Swearigen
MU-2L
Merlin III-A Merlin rJ-A Metro II
See Figure 2-1 for airplane models
in the above group that also have an option for a seating configura-
tion of less than 10 passenger seats .
RUNWAY LENGTH CURVES
EXAMPLE: TEMPERATURE AIRPORT ELEVATION 59°F (15°C) SEA LEVEL
EXAMPLE: TEMPERATURE AIRPORT ELEVATION 59°F (15°C) SEA LEVEL
2/24/83
GEN. UTILITY 3700' (1 128 m)
NOTE: For airport elevations above 3000 feet (914 m) use General Utilit Curves , Figure 4- l .
- en a: "' ...
LIJ
2 -... "' LIJ 1&.
% ... (!)
4000 (1219) z \IJ _,
~ ~ z :::) a:
L-.:w....l~.;.l..J … J...,L..W:...~'-... sooo ( tl4)
GEN. UTILITY 3700' (1 128 m)
50 15 100 ,., , 10 u .t ~7.1 c•c,
MEAN DAILY MAXIMUM TEMPERATURE OF THE HOOTEST MON'ffi· OF THE YEAR.
FIGURE 4-2. RUNWAY LENGTH TO ACCOMMODATE AIRPLANES HAVING A SEATING CONFIGURATION OF 10 PASSENGER SEATS OR MORE
Chap 4 Page 14
(
(
(
(
(
7/3/85 AC 150/5300-4B CHG 8
CHAPTER 5. LAND CONSIDERATION, OBSTRUCTION RESTRICTION, AND AIRPORT HAZARD REMOVAL
CHAPTER 5. LAND CONSIDERATION, OBSTRUCTION RESTRICTION, AND AIRPORT HAZARD REMOVAL
* 16. AIRPORT HAZARDS. Airport hazards have a substantial adverse effect upon the safe and efficient use of the airport by aircraft and upon the safety of persons and property located on or near the airport. The term object as used in the following paragraphs includes, but is not limited to, above ground structures, people, equipment, vehicles, aircraft, natural growth, and terrain. Flammable material storage facilities, including fuel truck fill stands and unloading facilities that are located in any of the following areas are airport hazards. The following objects are airport hazards and must be removed:
a. Objects in the airport's airspace that are of a greater height than any of the heights or surfaces defined in FAR 77.23 and that have not been the subject of an FAA aeronautical study. The FAA conducts an aeronautical study of any object when the FAA deems a study is necessary.
b. Objects in the airport ' s ai~space that the FAA has determined, as the result of aeronautical studies, to be hazards to air navigation.
c. Objects penetrating an established clearway plane. FAA approved frangible threshold lights 26 inches (66 em) or less above the runway end elevation and located to each side of the runway penetrating an established clearway plane are not considered airport hazards. The clearway is defined in paragraph 3.
d. Objects penetrating an imaginary surface or plane associated with an obstacle free zone (OFZ), a threshold, or a visual NAVAID. FAA approved frangible equipment that provides an essential aviation service and penetrates one of these imaginary surfaces or planes is not considered an airport hazard provided it is not an airport hazard as defined in paragraph 16.c. The penetration of any frangible equipment must be kept to a mimimum. The OFZ is defined in paragraph 3. Surfaces associated with thresholds are defined in appendix 9. The design clearance planes associated with visual NAVAIDs are defined in AC 150/5300-2.
e. Objects located in the runway safety area. FAA approved frangibly-mounted equipment that provides an essential aviation service and is located in the runway safety area is not considered an airport hazard provided it is not an airport hazard as defined in paragraphs 16.c or d. The frangiblymounted equipment in the runway safety area must be located as far as practical from the runway centerline. The runway safety area dimensional standards are provided in paragraph 28 and in AC 150/5300-12,
Chap 5
Par 16
paragraph 14. *
*
AC 150/5300- 4B CHG 8 7/3/85
AC 150/5300- 4B CHG 8 7/3/85
f . Objects located either between a runway centerline and its aircraft parking line limits or within 0.75 times the wingspan of the most demanding airplane plus 7 feet (2m) from a taxiway centerline. Frangibly-mounted equipment that provides an essential aviation service, airport service vehicles required to be in these areas for efficient airport operations, and holding and taxiing aircraft located in these areas are are not considered airport hazards provided they are not airport hazards as defined in paragraphs 16.c, d , or e. The frangibly-mounted equipment in these areas must be located as far as practical from the runway and taxiway centerlines. The runway centerline to aircraft parking area separation standard is provided in paragraph 28 and in AC 150/5300- 12, paragraph 13. The aircraft parking line limit extends beyond the runway ends for a distance of at least 4 times its separation distance from the runway centerline.
g.
h.
i .
Objects located either between a runway centerline and its building restriction lines (BRLs) or within 0. 63 times the wingspan of the most demanding airplane plus 7 feet (~ m) from a taxilane centerline. Equipment that provides an essential aviation service, airport service vehicles, aircraft, and people required for efficient airport operations
located in these areas are not considered airport hazards provided they are not airport hazards as defined in paragraphs 16.c, d, e, or f . The runway centerline to BRL separation standard is provided in paragraph 28 and in AC 150/5300-12, paragraph 13. The BRLs extend beyond the runway ends for a distance of at least 3,000 feet (900 m) or 4 times their separation distance from the runway centerline whichever is less.
Ditchs, rough surfaces, soft spots, or pending areas located in a runway or taxiway safety area. Gentle drainage swales may be located near the runway or taxiway. The taxiway safety area dimensional standards are provided in paragraph 28 and in AC 150/5300-12, paragraph 23.
Garbage dumps or landfills located within 5,000 feet (1 500 m) of a nonturbojet runway or 10,000 feet (3 000 m) of a turbojet runway that may attract birds on or around an airport.
17. RECOMMENDED CLEARING. Objects, other than airport hazards, for which removal is recommended include:
a . Obstructions that have adverse effect on air navigation as determined by FAR Part 77 or an aeronautical study;
b . The controlling obstacle to an existing or planned terminal instrument procedure that impairs the efficiency or capacity of an airport;
c. Objects which adversely affect departures; and
d. Objects located in a runway clear zone as defined in paragraph 3.
Chap 5
Par 16
(
(
*
(
(
(
7/3/85 AC 150/5300-4B CHG 8
7/3/85 AC 150/5300-4B CHG 8
* 18. ZONING AND LAND USE COMPATIBILITY.
a. Land Use. Unconstrained use of land adjacent to or in the immediate v~c~ nity of the airport can directly affect the efficiency and capacity of the airport . Airport authorities should:
(1) Prevent the construction, erection, alteration, or growth of any structure, tree , or other object in the approach areas of the runway or the airport, which would constitute an airport hazard; and
(2) Restrict the use of land adjacent to or in the immediate vicinity of the airport to activities and purposes compatible with normal airport operations including landing and takeoff of aircraft.
This may be accomplished by acquiring and retaining easements , other interests, or rights for the use of land and airspace; or by adopting and enforcing zoning regulations .
b. Noise Compatibility. Recipients of Federal aid for airport development need to assure that appropriate action, including the adoption of zoning laws, has been or will be taken, to a reasonable extent, in restricting the use of land adjacent to or in the immediate vicinity of the airport to activities and purposes compatible with normal airport operations. Zoning ordinances developed for airspace protection will not necessarily ensure compatibile land use, with respect to noise, in the vicinity of the airport . Depending on the local situation, measures other than zoning or in addition to zoning may be necessary to achieve compatible land use
Chap 5
Par 18
with respect to noise .
(1) FAA Order 5050.4, Airport Environmental Handbook (available at FAA Airports Offices) provides guidance on land use compatibility. Appendix 1 of AC 150/5020:1, Noise Control and Compatibility Planning for Airports, contains a table identifying land uses normally compatible with various levers of noise exposure. The advisory circular also includes information on alternative strategies to achieve compatible l and use.
(2) The airport operator may find it desirable to develop a comprehensive airport noise compatibility program in accordance with FAR Part 150, Airport Noise Compatibility Planning. The development of this program is recommended when a significant problem exists relative to noise and land use compatibility. Such a program must include recommended actions to reduce noncompatible areas identified in a thorough
evaluation of existing and future noise and land uses in the airport vicinity. The program is developed in consultation with FAA, airport users , the state, and affected communities. The FAA approved program recommendations may be eligible for Federal aid under the Airport Improvement Program. *
*
AC 150/5300-4B CHG 8 7/3/85
AC 150/5300-4B CHG 8 7/3/85
c . zoning Ordinance. Zoning is adequate where the control is in line with the public interest in health, safety, and general welfare.
(1) ZOning laws and ordinances, enacted in the vicinity of an airport, need to concentrate on airspace protection, compatible land use, noise sensitive areas, esthetics, and consistency with master plans.
(2) Each section of a zoning ordinance is independently justified. Thus, to eliminate misapplication in granting variances, consideration must be given to the justification for each section of the zoning ordinance. An example of misapplication would be the use of an FAA airspace determination of NO HAZARD TO AIR NAVIGATION, which is
limited to consideration of the navigable airspace, as the only justification for a variance to the zoning ordinance.
( 3) FAA guidance in developing zoning ordinances dealing with protecting the navigable airspace in the vicinity of the airport is contained in AC 150/5190-4, A Model Zoning Ordinance to Limit Height of Objects Around Airports.
19. LAND ACQUISITION.
a. The amount of land needed for any one of the four groups of utility airports will vary considerably. Factors, such as length and number of runways, lateral, clearances , areas required for buildings, hangars,
(
*
aircraft tiedown, transient apron, automobile parking, and future expan- ( sion of the airport, should be studied in detail, and a plan for the construction and expansion of the airport, such as an airport layout plan, developed.
b . In the preliminary stage of airpo~t development, it is desirable to know the approximate number of acres needed for the airport . Figure 5-3 indicates the approximate acreage needed for each group of airports broken down i nto three segments.
(1) Landing Area . This includes the runway, safety area, taxiways, and lateral clearances to building restriction lines. The acreages shown are based on a single-runway airport . If an additional runway is needed, a separate calculation must be made for the additional
landing area and to provide unrestricted line-of- sight between runways.
(2) Runway Approach Areas. The airport owner should acquire control of the property within the runway clear zone, between the building restriction lines, and as may be required for airport hazard removal and approach protection (see paragraph 16) . For those cases where this may be impossible or economically unfeasibl e, control of the land within the building restriction lines and that required for airport hazard removal and approach protection is an acceptable minimum. These areas are the most critical areas under the approach paths. Therefore, control of these areas is essential, and it is preferably acquired by purchase of the land fee title . If fee title cannot be
Chap 5
Par 18
(
(
(_
(
7/3/85
{3)
AC 150/5300-4B CHG 8
AC 150/5300-4B CHG 8
obtained, avigation easements may be acquired, although this is less desirable. The acreage required for airport hazard removal and approach protection varies with location, depending on the environment around the approach ends of the runway, local laws and ordinances, and the airport owner's ability to zone around the airport.
Building Area.
(a) This includes all areas beyond the building restriction line which usually are the fixed-base operator facility, T-hangars,
tiedowns, transient parking apron, automobile parking, access road, and utilities. In determining the configuration of the building area, physical factors, such as terrain, drainage, and land uses, will affect the efficiency of the layout.
(b) As the type of airport progresses from Stage I to General Utility, it has been assumed that the activity on the airport will also increase. For example, Stage I building area provides for two 10-unit T-hangars, tie downs for 10 airplanes, a parking apron for 10 transient airplanes, a 40-car parking lot, access road, and utilities. (This area is considered minimum.) If feasible, additional area should be acquired early in the airport's development for long-range expansion. The General Utility airport building area provides for two fixed-base operators, ten 10-unit T-hangars, tiedowns for 50 airplanes, a parking apron for 50 transient airplanes, a 100-car parking lot, access, road, and utilities. However, this is an illustration only since activities at the metropolitan airport may differ by as much as twofold or threefold over a community airport.
20. ACQUISITION PROCEDURES. The acreag~s given in figure 5-3 are calculated on the basis of an airport configuration closely approximating that illustrated. Nevertheless, it is realized that the layout of existing lots and parcels will often require acquisition of land which will result in a considerable variation from this configuration. Figure 5-4 shows an example of approach area acquisition related to existing parcel boundaries. The dashed lines represent the area which should be acquired to meet minimum requirements. However, if it is impractical or unfeasible to acquire a portion of the parcels, an evaluation must be made to determine the effect of deviation from
the standard. The recommended property line on figure 5-4 represents one probable configuration of an approach area acquisition for the airport question.
21. FUTURE EXPANSION. It is a well-established fact that land around a metropolitan airport increases in value after the airport is built. To a lesser degree, this is also true for the community airport. Accordingly, parcels of land purchased beyond the minimum needed will often prove to be essential in permitting future expansion of the airport. This matter should be given
detailed consideration during the airport master planning study. Generally, airport land should be acquired not only to meet the minimum requirements but also to accommodate future development of the airport required to realize its ultimate role. It may be feasible for this additional land (needed in the
future) to be leased until required for airport development.
Chap 5
Par 19 Page 19
AC 150/5300-4B CHG 8 7/ 3/85
AC 150/5300-4B CHG 8 7/ 3/85
22. USE OF LAND FOR NONAERONAUTICAL PURPOSES.
a . The two areas on an airport which could be available for use by nonaeronautical activities are the portion of the building area reserved for future airport development and the runway approach area. Certain functions may be allowed in these areas to produce revenue for the airport provided present and future operations of the airport are not jeopardized.
( 1) Building Area . A building area not needed immediately for airport development may be used for revenue-producing purposes by a variety of nonaeronautical activities . SUch activities could be agricultural, recreational, commercial, or industrial . For example, airport property along a highway might provide good potential for small retail business which require a minimum investment in facilities . Again allow only short-term leases giving due consideration to the planned future of the area in question.
(2) Runway Approach Areas. Congregation of people or establishment of facilities, such as garbage dumps or land fill facilities that would attract birds, must be avoided within the runway clear zones .
Limited agricultural uses, such as raising low growing crops, are compatible with the immediate runway approach area . Long- term leases in this area are not recommended unless recapture clauses are included since the l and may be required within the period for airport uses such as runway extensions. etc.
b . Also , consider the possibility of establishing an industrial area on or adjacent to the airport. Guidance on this subject is provided in AC 150/5070-3, Planning the Airport Industrial Park. However, check the function of the activity to ensure no interference with the airport. For example, do not permit installation of lighting systems which could be confused with the runway lights, or industries which might produce electromagnetic or electronic disturbances which would interfere with aircraft navigational or communications equipment, or cause visibility problems due to smoke , dirt, steam, or fog. Also, limit the height of all structures to prevent airspace encroachment.
Page 20 (thru 22)
Chap 5
Par 22
(
(
(
2/24/83 AC 150/5300-48 CHG 6 (
(
Withdrawn--Change 6
(
Chap 5
Page 21 (and 22)
'tl Ill IQ ro
N w
0 =:r Ill '0
<.n
"l 1-1 G) c:: 61
<.n
I w .
3: H z H 3: §!
t"' ~ 0
61 0 c:: 1-1 ~ ~ z >-3 ~
/' /\
LANDING AREA APPROACH
LANDING AREA APPROACH
AREA I RUNWAY I APPROACH
AREA
I BUILDING AREA ' L__
RUNWAY LENGH LANDING AREA APPROACH AREA BUILDING AREA TOTAL AREA IN RUNWAY TYPE IN FEET (METERS) IN ACRES IN ACRES IN ACRES** ACRES BASIC UTILITY 2 000 (600) 2 3 21 8 52 STAGE I 3000 ( 900) 32 2 I 8 61 4000 (I 200) 41 21 8 70 5000 ( 15 00) 50 2 I 8 79
I BUILDING AREA ' L__
BASIC UTILITY 2500 ( 750) 27 2 I I 2 60 STAGE n 3500 (1050) 36 21 12 69 4500 (1350) 45 2 I I 2 78 55 00 (1650) 54 2 I I 2 8 7
GENERAL UTILITY 3000 (900) 39 30 24 93 STAGE I 4 000 (1200) 5 I 30 24 105 5000 (I 500) 63 30 24 I I 7 6000 (I 800) 75 30 24 129
GENERAL UTILITY 3500 (IOSO) 90 12 5 24 2 39 STAGE n 4500 (1350) 113 125 24 262 5500 (I 6 50) 136 125 24 2 85 6500 (1950) 15 9 12 5 24 308
**THESE FIGURES VARY DUE TO ASSUMED HIGHER DEGREE OF ACTIVITY AT THE HIGHER TYPE OF AIRPORT
~
IV - IV J::> - 00 w
)> 0
1-' <.n 0 …
<.n w 0 0 I .e. til
0 :I: G)
0'1
AC 150/5300-4BCHG 6
AC 150/5300-4BCHG 6
ET.
PARCEL STAIONCSTION RECSIIDRION
2 3
COYDRUAD
C
2/24/83
,0001
200 VARIES
RUAY
FIGURE 5-4. LAND ACQUISITION FOR APPROACH PROTECTION
Chap 5
(
(
6/24/75 AC l 50/5300-4B
CHAPTER 6. SITE INVESTIGATION
23. GENERAL. There are many factors which must be considered in selecting an airport site . These factors include such things as accessibility to the users; Government regulations affecting airport development; ease with which the site can be developed; the existence of obstacles that might interfere with aeronautical operations; the occurrence of conditions of reduced visibility (fog, smoke , etc.); the effect of the development on the surrounding environment; and the feasibility of future expansion and instrument operations . Advisory Circular 150/5070-6, Airport Master Plans , discusses in detail the subject of airport selection. The primary purpose of this chapter is to briefly present the Government regulations that must be considered and the engineering factorR that must be analyzed in reviewing potential sites for a utility airport.
CHAPTER 6. SITE INVESTIGATION
24. GOVERNMENT REGULATIONS.
a. Federal Aviation Regulations Part 157, Notice of Construction,
Alteration, ~tivation, and Deactivation of Airports, requires that
the FAA Airports District Office or regional office be notified by persons proposing to construct, alter, activate , or deactivate a civil airport. The FAA will conduct an aeronautical study to determine the effect of the proposal on the safe and efficient use of airspace. Upon compl€tion of the study, the proponent will be notified of the FAA' s determination. Advisory Circular 70- 2, Airspace Utilization Considerations in the Proposed Construction, Alteration, Activation and Deactivation of Airports, discusses in detail this FAR Part 157 requirement. This advisory circular also contains the addresses and geographic jurisdictions of the FAA offices. These offi ces should also be contacted to determine the requirements which must be met if it is desired to develop the airport with Federal funds.
b. In addition, most states require their approval of the proposed airport through licensing or some similar means. The state in which the proposed airport will be located should be contacted directly to determine that state 's requirements.
c. The local governing body should also be contacted to determine if
they have any laws that may affect the proposed airport.
25. ENGINEERING ASPECTS OF SITE INVESTIGATION. An investigation of all potential sites must be made for two purposes: to determine an estimated cost of development, and to allow a comparative analysis of all
potential sites. The services of an experienced engineer should be enlisted since the investigation will require a thorough knowledge of engineering principles and practices . The factors that should be analyzed in selecting an airport site are presented in the following paragraphs. For convenience, a checklist for the required engineering information is included in Appendix 2 of this publication.
Chap 6 Par 23 Page 25
AC l50/5300-4B CHG 3 12/5/78
~ . Site Clear ing. Site clearing should be analyzed from the standpoint ( of removing all objects (trees , buildings, powerlines , etc . ) that may affect airplane operations (see Chapter 5) . This often requires clearing both the landing area and the runway approaches.
b. Soil Survey. A preliminary soil s survey is conducted to evaluate soils to approximate their classification in accordance with the FAA method for classifying soils . This method is described in Advisory Circular 150/5320- 6, Airport Pavement Design and Evaluation. This will involve field investigation and office research of available data .
c . Drainage. Preliminary drai nage investigation must determine the general limits of all drainage areas which affect t he airpor t site, including tributary areas beyond the airport boundary. The maximum rainfall expected once in 5 years is generally recommended for estimating runoff for airports. A detailed discussion of this factor is contained in Advisory Circular 150/5320- 5 , Airport Drainage .
d. Grading. Preliminary gradi ng layout, based upon a reasonably balanced runway profile, should allow a general estimate of the
cubic yards of earth that must be moved for cut and fill and borrow operations. The maximum and minimum allowable transverse and l ongitudinal slopes for the airport will greatly restrict the possibilities for alternate grading schemes. Further, the drainage system must be considered jointly with grading since each affects the design of the other.
e . Paving. Pavement investigation includes a preliminary design of both the airport and access road pavements . It also requires determination of the availability and source of the various materials to make up the pavement structure . Wit h these data, an estimate of the cost for pavement construction can be made. Chapter 12 discusses this subject in more detail.
f. Turfing. Turfing will usually provide the most economical means for protecting airport areas which are subject t o wind or water erosion. Local conditions should dictate the choice of grass species for the turf. (The local office of the County Agent, Department of Agricul t ure , Soil Conservation Service is available to assist in the selection of appropriate grasses. )
g. Airport Lighting._ Preliminary layout of t he airport lighting
system should include the runway lights , visual approach slope indicators (VASI), lighted wind cone, ducts, control s, and air- * port beacon. Advisory Circulars 150/5340- 24, Runway and Taxiway Edge Lighting Systsm,ana 150/5340- 25, Visual Approach Slope Indicator (VASI) Systems, provide guidance for estimating t he requirements of the *
Page 26
Chap 6 Par 25
(
(
(
2/24/83 AC 150/5300-48 CHG 6
*
h.
lighting system. In many cases, lighting may not be justified initially. Nevertheless, future planning should recognize the need for a lighting
system and initial construction should include installation of ducts under pavement for the lighting system. Lighting of obstructions may also be required.
Utility System. Preliminary design of the utility system includes general layout of the water, sewer, communications, and power systems. In some locations, this will require provisions for on-si te water supply and sewage disposal. Local ordinances often govern design criteria for these facilities.
i. Site Location Compatibility. Airport-community compatibility is as important to the longevity of a utility airport as good pavement design . Airport-community compatibility is established by assuring that land uses within the airport-aircraft operational impact areas are limited to those uses that are compatible with the normal day-to-day activities at and around the airport facility. The airport site should be located in an area that is compatible and has the potential to remain compatible through land use controls. Land-use compatibility guidelines, based on yearly day/night average sound levels (Ldn), are found in Table 2, Appendix A of FAR Part 150, Airport Noise Compatibility Planning. For other environmental compatibility information, see FAA Order 5050.4, Airport Environmental Handbook. (This Order may be obtained by request at any FAA Airports
Chap 6 Par 25
Office.) *
Page 27 (and 28)
(
(
(
9/23/83 AC 150/5300-48 CHG 7
CHAPTER 7. DESIGN CRITERIA AND DIMENSIONAL STANDARDS
CHAPTER 7. DESIGN CRITERIA AND DIMENSIONAL STANDARDS
26. GENERAL. The design standards represent a recognition of absolute minimum requirements for airplane operations plus a safety margin based upon airport research as well as operating experience. For example, the absolute minimum requirement for taxiway width is the outside-to-outside dimension of the landing gear configuration. The standard, however, provides additional width to account for the realities of airplane operations in daylight, nighttime, and all-weather conditions. Appendix 1 of AC 150/5300- 12 discusses the effect of airplane physical characteristics on the design of airport elements. That rationale may be used on a case-by-case basis in adapting airport design standards and recommendations, primarily at existing airports, to accommodate unusual local conditions or a specific airplane within an airplane design group.
27. FUTURE ROLE CONSIDERATIONS. In applying design standards, airport authorities need to determine the airport's future role. Initial development of the airport should be planned to accommodate the future role. For example , when the initial and ultimate needs, respectively, are to accommodate airplanes in Airplane Design Groups I and II, the pavement widths for Airplane Design Group I should be used in conjunction with the lateral clearances of Airplane Design Group II. Specifically, the runway and taxiway widths should be 60 feet
(18m) and 25 feet (7.5 m), but with a runway to taxiway separation of 240 feet (72 m), rather than 150 feet (45 m) •
* 28. DIMENSIONAL CRITERIA. Figure 7-1 specifies the m1n1mum lengths, widths, and clearances for airport design. At least one set of dimensions is tabulated for each runway instrumentation configuration and airplane design group combination assuming 95 percent wind coverage. For airports with runway wind coverage of less than 95 percent, a crosswind runway may be needed (see chapter 3), or an increase in dimensions may be considered.
a. The Airplane Design Group I dimensions are for airports expected to serve
airplanes in Aircraft Approach Category A and B with wingspans up to but
not including 49 feet (15 m) • This airplane design group has two sets of dimensions; one for facilities expected to serve only small airplanes and another for facilities expected to serve large airplanes .
b. The Airplane Design Group II dimensions are for airports expected to serve
airplanes in Aircraft Approach Category A and 8 with wingspans up to but
not including 79 feet (24 m) .
c. The Airplane Design Group III dimensions are for airports expected to serve
airplanes in Aircraft Approach Category A with wingspans up to but not
including 118 feet (36 m) and airplanes in Aircraft Approach Category 8 with wingspans up to but not including 79 feet (24 m). For this airplane design group, the dimensional standards for prec1s1on instrument, nonpreci-
sion instrument, and visual runways are the same.
d. The dimensional standards for airport components expected to serve faster and larger airplanes are in AC 150/5300-12 .
Chap 7 Par 26 Page 29
AC 150/5300-48 CHG 6 2/24/83
* 29 . TYPICAL AIRPORT LAYOUT. Figure 7-2 illustrates the application of the dimensional standards and is keyed to the items in figure 7-1. This typical layout of a portion of an airport shows the relationship between the runway, taxiway, runway clear zone , building restriction line, and property line.
30. RUNWAY AND RUNWAY SAFETY AREA LONGITUDINAL GRADE. The longitudinal grade limitations .for the runway and the runway safety area along the runway are shown in figure 7-3. For the first 200 feet (60 m) of runway safety area beyond the runway end, the longitudinal grade needs to be such that the primary surface is not penetrated nor the grade steeper than 3 percent. The longitudinal grade limitations for the remainder of the runway safety area are shown in figure 7-6. In stage construction, it is important to consider the line-ofsight standard for the ultimate runway length.
31. LINE-OF-SIGHT. Line-of-sight standards impose an additional restraint on surface gradients. It is desirable to provide an unobstructed line-of- sight along the entire length of an individual runway or taxiway, as well as along the entire length of an intersecting runway. The following paragraphs provide line-of-sight standards:
a. Along Individual Runways.
(1) Airports Not Having a 24-hour Control Tower. Runway grade changes shall be such that any two points 5 feet (1.5 m) above the runway centerline will be mutually visible for the entire runway length.
However, if the runway has a parallel taxiway for its full length,
runway grade changes may be such that an unobstructed line-of- sight will exist from any point 5 feet (1.5 m) above the runway centerline
to all other points 5 feet (1.5 m) above the runway centerline within a distance of half the length of the runway.
(2) Airports Having a 24-hour Control Tower. Although it is desirable to provide the above line-of-sight for the entire runway length , adherence to longitudinal gradient standards will provide an adequate line-of-sight. However , before applying these criteria, a careful analysis must be made of forecasted airport traffic to ascertain whether the tower will remain in 24-hour operation. Visibility requirements from the airport traffic control tower to the airport surface areas used in aircraft ground movement must also be considered .
b. Between Intersecting Runways.
Page 30
(1) Airports Not Having a 24-hour Control Tower. Runway grades, terrain, structures, and permanent objects must be such that there will be unobstructed line-of-sight from any point 5 feet (1.5 m) above one
runway centerline to any point 5 feet (1.5 m) above an intersecting runway centerline , both points being within the area of the runway visibility zone . The runway visibility zone is an area formed by imaginary lines connecting the two runways' visibility points as shown in figure 7-4. The location of each runway's visibility points is determined in the following manner:
Clap 7
Par 29
(
*
(
(
(
(
2/24/83 AC 150/5300-48 CHG 6
*
(a) when the distance from the intersection of two runway centerlines to a runway end is 750 feet (250 m) or less, the visibility point is located on the centerline at the runway end;
(b) when t he distance from the intersection of two runway centerlines
to a runway end is greater than 750 feet (250 m) but less than 1,500 feet (500 m), the visibility point is located on the centerline, 750 feet (250 m) from the intersection of the runway centerlines; or
(c) when the distance from the intersection of two runway centerlines
to a runway end is equal to or greater than 1,500 feet (500 m), the visibility point is located on the centerline and equidistant from the runway end and the intersection of the centerlines.
(2) Airports Having a 24-hour Control Tower. Although it is desirable to provide an unobstructed line-of-sight along the entire length of an
intersecting runway, there are no mandatory line-of-sight requirements between intersecting runways at these airports. However, analysis should be made of forecasted airport traffic to ascertain whether the tower will remain in 24-hour operation.
c. Taxiways. There are no specific line-of-sight requirements for taxiways . However, the sight distance along a runway from an intersecting taxiway
must be sufficient to allow a taxiing aircraft to enter safely or cross the runway.
32. TYPICAL CROSS SECTION. The transverse grade limitations for the runway and other airport surfaces are shown in figure 7-5. The transverse grade limitations for the portion of the runway safety area beyond the runway ends are in figure 7-6. The established transverse grades of the runway safety area, as shown in these figures, are necessary to maintain proper drainage and to control erosion. The grading for stage development should be compatible with the ultimate proposed final grades of a particular area . Failure to plan accordingly may lead to costly grade adjustments, resurfacing, and the
rebuilding of drainage facilities or other structures during later stages of airport development.
33 . APPLICATION OF DIMENSIONAL STANDARDS. An airport design standard suitable for use in all parts of the Nation, for a variety of airplanes and under many variations in local conditions, is based upon broad considerations. Where such a national standard is to be modified for a particular airport , competent engineers are required to adapt the standard to local conditions.
a . Certain standards, such as the standard for the transverse grade of the runway safety area, are expressed as a maximum and a m~n~mum. The range presented reflects a standard adequate for surface drainage but not in excess of the reasonable requirements for safe and efficient airplane operation.
b. The standards in figure 7-1 are also applicable to runways provided especially for airplanes in Aircraft Approach Category A and B at Transport Airports. However, regard must be given to assure that lateral clearances are maintained for airplanes in Aircraft Approach Category C and D.
Chap 7
Par 31 Page 31 (and 32)
*
(
(
9/23/83 AC 150/5300- 4B CHG 7
9/23/83 AC 150/5300- 4B CHG 7
NONPRECISION & VISUAL RUNWAY PRECISION INSTRUMENT RUNWAY
ITEM DIM AIRPLANE DESIGN GROUP AIRPLANE DESIGN GROUP !/ r---~~----.-----~-----.----~~-=~~--~ IY
Runway
Length
Width
Runway Safety Area 3/
Length Beyond Runway End if
Width
Taxiway
Width
Taxiway Safety Area
ITEM DIM AIRPLANE DESIGN GROUP AIRPLANE DESIGN GROUP !/ r---~~----.-----~-----.----~~-=~~--~ IY
Width
Separation Distance:
A
B
2C
c
D
Wingspan < 49 '
60 ft 18 m
240 ft 72m
120 ft 36 m
25 f t 7.5 m
49 ft 15m
I II Wi ngspan Wingspan < 49' < 79 '
- Refer
60 ft 75 ft 18 m 23 m
240 ft 300 ft 72m 90 m
120 ft 150 ft 36 m 45 m
25 ft 35 ft 7. 5 m 10.5 m
49 ft 79 ft 15m 24 m
I y I II III Wingspan Wingspan Wingspan Wingspan
( 49' < 49' < 79' ( 118'
to chapter 4 -
75 ft 100 ft 100 ft 100 f t 23 m 30 m 30 m 30 m
600 ft 600 ft 600 ft 600 ft 180 m 180 m 180 m 180 m
300 ft 300 ft 300 ft 300 ft 90 m 90 m 90 m 90 m
25 ft 25 ft 35 f t 50 ft 7.5 m 7.5 m 10. 5 m 15 m
49 ft 49 ft 79 ft 118 ft 15 m 15 m 24 m 36 m
Runway Centerline to;
Parallel Runway Centerline 700 ft 700 ft 700 ft - Refer to AC 150/5300-12 - 210 m 210 m 210 m
Parallel Taxiway Center line ~1 E 150 ft 225 ft 240 ft 200 ft 250 ft 300 ft 350 ft 45 m 67.5 m 72 m 60 m 75 m 90 m 105 rn
Building Restriction Line and F Aircraft Parking Area i/
Runway Centerline and End to;
Object
Property Line G
125 ft 27.5 m
69 ft
200 ft 250 f t 60 m 75 m
- Refer
- Refer
69 ft 103 ft
'1.1 7/ '1.1 '1.1 y ll y y
to paragraph 16 -
to paragraph 19 -
69 ft 69 ft 103 ft 153 ft Taxiway Centerline to;
Parallel Taxiway Center line
21 m I 21 m 31.5 m 21 m 21 m 31.5 m 46.5 m
Parked Aircraft and Object H - Refer to paragraph 16 -
Taxilane Centerline to:
Parked Ai rcraft and Object - Refer to ParaqraPh 16 - !/ Letters are keyed to those illustrated in figure 7-2
~/ These dimensional standards are for fccilities which are to serve only small airplanes.
11 This runway safety area standard applies to all runways and runway extensions, that are constructed or upgraded after February 24, 1983. For other runways, the maximum feasible length and width of runway safety area should be ptovided. il These distances may need to be increased to keep the stopway within the runway safety area.
~/ The location of a parallel taxiway may be adjusted such that no part of an aircraft (tail , wing tip) on
taxiway centerline penetrates the obst acle free zone (OFZ) . if Objects l ocated outside of the building restriction lines may penetrate the airport imaginary surfaces
defined in Subpart C of FAR Part 77 where an FAA aeronautical s tudy has determined that the specific
penetration will not result in a hazard to air navigation. ll The building restriction line for a Category I ILS runway precludes any part of a building, tree , or parked
aircraft from penetrating surfaces originating 300 feet (90 m) from runway centerline and sloping laterally outward 4 (horizontal) to 1 (ve,ticall.
FI GURE 7- 1. DIMENSIONAL STANDARDS
FI GURE 7- 1. DIMENSIONAL STANDARDS
Chap 7
~ Ill IQ
ID w ~
() ::r Ill 'tl
~ -
"'l H C) c ~
-...I
I N .
;r;. H :u ('3
~
~ c ~
~--~--- --
RUNWAY CLEA
(SEE APPENDIX
R ZONE -1--
6)
I I
2C
--
200' -,- ( 60m)
t I +--- -- c -
~ / - 0 1--- L r--
… J
-- --~
NOTES:
I. DIMEN
2. PREFE
PARKING AREA IS NEAR MIDPOINT OF RUNWAY.
2. PREFE
~
-- l
--
•
A I I G
I
4 - 8 - t
E F t
0 -- ~- --_r -- J -r-~f+--- ------
I I I . ---·· • · ·- -
- …
f;
1-' V1 0 …
V1 w 0 0 I ~ O:J () :I: C)
01
N …
N .:::. …
00 w
"d Ill ()Q
(l) w VI
,..--.
n ::r ~
…
(\
PROFilE OF CENTERLINE OF RUNWAY . H >
A ~~~~ :::I CURVE \~ ~I U:NGTil 07. ro 2% . ,> ~·
PROFilE OF CENTERLINE OF RUNWAY . H >
Pol - I ___/~ . H
DISTANCE BETWEEN CHANGES IN GRADE ~ 250 X SUM OF A + B IN PERCENT
VERTICAL CURVES
> . ~
LENGTH OF VERTICAL CURVES WILL NOT BE LESS THAN 300' FOR EACH 1% GRADE CHANGE , EXCEPT THAT NO VERTICAL CURVE WILL BE REQUIRED ~N GRADE CHANGE IS LESS THAN 0.4%.
SIGHT DISTANCE
SIGHT DISTANCE
SEE PARAGRAPH 31.
GRADE CHANGE
MAXIMUM GRADE CHANGE SUCH AS (A) OR (B) SHOULD NOT EXCEED 2%.
FIGURE 7-3 . LONGITUDINAL GRADE LIMITATIONS
~
~ s Vl
g:;
1-' VI 0 - VI w 0 0 I ~ b'
AC 150/5300-4B
l ~ - - 0
WHEN
A < 750'
B < 1500'
BUT > 750' c ~ 1500'
D > 1500'
THEN
xo = DISTANCE TO
END OF RUNWAY
Continue reading ↓ 120 of 183 passages shown