Radar Vectors
Advisory Circular Current Issued Jul 2, 2018 AFS-400 128 pages Copy saved Nov 18, 2026

AC 120-118 Criteria for Approval/Authorization of all Weather Operations for Takeoff, Landing, and Rollout

This advisory circular (AC) provides an acceptable means, but not the only means, for obtaining and maintaining authorization of operations in Category (CAT) I, CAT II, and CAT III landing weather minima and instrument flight rules (IFR) lower-than-standard takeoff minima. This AC does not change, add, or delete regulatory requirements or authorize deviations from regulatory requirements. This AC addresses the operational authorizations formerly published in AC 120-28, Criteria for Approval of Category III Weather Minima for Takeoff, Landing, and Rollout, and AC 120-29, Criteria for Approval of Category I and Category II Weather Minima for Approach, and any subsequent developments.

Official source ↗ Open PDF

This advisory circular (AC) provides an acceptable means, but not the…

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Criteria for Approval/Authorization of

All Weather Operations (AWO) for Takeoff, Landing, and Rollout

Date: 7/2/18 Initiated by: AFS-400

AC No: 120-118

Change:

This advisory circular (AC) provides an acceptable means, but not the only means, for obtaining and maintaining authorization of operations in Category (CAT) I, CAT II, and CAT III landing weather minima and instrument flight rules (IFR) lower-than-standard takeoff minima. This AC does not change, add, or delete regulatory requirements or authorize deviations from regulatory requirements. This AC addresses the operational authorizations formerly published in AC 120-28, Criteria for Approval of Category III Weather Minima for Takeoff, Landing, and Rollout, and AC 120-29, Criteria for Approval of Category I and Category II Weather Minima for Approach, and any subsequent developments.

John S. Duncan Executive Director, Flight Standards Service John Duncan's signature

Page iii

CONTENTS Paragraph Page

CHAPTER 1. INTRODUCTION … 1

1-1. Purpose … 1 a. Overview … 1 b. Regulatory Basis … 1 c. International Harmonization … 1 d. Nomenclature Changes … 1 e. CAT III Landing Minima … 1 f. All Weather Operations … 2 g. Responsible Flight Standards Office … 2 h. Dispatcher … 2 1-2. Where You Can Find This AC … 2 1-3. Relationship of This AC with AC 20-191 and Their Impact Upon AC 120-29A and AC 120-28D … 2 1-4. Applicability … 2 1-5. Explanation of Content … 2 a. Takeoff, Approach, Landing and Rollout Operations … 3 b. Enhanced Flight Vision Systems (EFVS) and Synthetic Vision Guidance

Systems (SVGS) … 3 c. New Technology Demonstration (NTD) … 3 d. Operator Use Suitability Demonstration (OUSD) Changes … 3 e. Satellite-Based Augmentation System (SBAS) … 3 1-6. Related Regulations and References … 4 a. Title 14 CFR … 4 b. ACs, FAA Orders, and Operational Authorizations … 4 c. OpSpecs/MSpecs/LOAs … 5

CHAPTER 2. BACKGROUND … 7

2-1. Operational Authorizations Versus Airworthiness Demonstrations … 7 2-2. Explanation of Terms … 7 2-3. Approach Terminology … 7

CHAPTER 3. OPERATIONAL CONCEPTS … 9

3-1. Instrument Operations … 9 a. Airborne Systems … 9 b. Magnetic Variation (MagVar) Data and Onboard Database … 9 c. Airborne Databases and Interface … 11 3-2. Takeoff … 11 a. Takeoff Minima … 11 b. Pilot Assessment of Equivalent RVR … 11 3-3. Landing … 12 a. Approach and Landing Concepts … 12

Page iv

b. Acceptable Instrument Approach Procedure (IAP) Basis … 13 c. Considerations for the Use of Procedures Other Than U.S.

Standard Procedures … 13 d. Special IAPs … 14 e. Glide Path Angle (GPA) and Vertical Descent Angle (VDA) … 14 Table 3-1. Maximum Standard Approach Design Glide Path Angles/Vertical

Descent Angles … 14 f. Steep Angle Approach … 14 3-4. Engine Inoperative CAT II/III … 15 3-5. Go-Around Safety … 15 a. CAT I Go-Around … 15 b. CAT II/III Go-Around … 15 c. Automatic Go-Around … 15 3-6. Requirements for CAT I Operations … 15 a. General Requirements … 15 b. CAT I Landing Minima with Reduced Lighting (RVR 1800) … 15 3-7. Requirements for Operations Below RVR 1800 to 1000 … 16 a. General Requirements … 16 b. Specification of CAT II DA/DH … 16 c. Eligibility for CAT II Minima Not Less Than 100 Feet DA/DH … 16 d. Use of IM … 16 e. SA CAT I … 17 f. SA CAT II … 18 g. CAT II Using RVR 1000 Minima … 18 Table 3-2. Special Authorization Category II and Category II Minima Matrix … 19

h. Application of a DA/DH or Equivalent (e.g., IM), for CAT II … 19 i. Visual Reference Requirements … 19 j. Precision Approach Radar (PAR) … 20 3-8. Requirements for Operations Below RVR 1000 … 20 a. General CAT III Requirements … 20 b. Concepts and Objectives … 20 c. Fail Operational (FO) CAT III Systems … 21 d. Alert Height … 23 e. Fail Passive CAT III Systems … 24 f. Decision Height … 25 g. CAT III Operations with Not Lower than RVR 700 Landing Minima … 25 h. CAT III Operations with Landing Minima RVR 600 or Less … 26 i. CAT III Operations RVR Minima Rationale … 27 Table 3-3. Lowest Minima Currently Authorized for Fail Operational or Fail

Passive Landing Systems, or Landing and Rollout Systems … 28 j. Previously Approved CAT I/II/III Operations or Use of Previous or New

CAT I/II/III Criteria … 28 3-9. Visibility and RVR … 29 a. Meteorological Visibility … 29 b. Overseas Visibility Reporting … 29 c. Non-NWS Sources … 29

Page v

3-10. Runway Visual Range … 29 a. Controlling RVR … 29 b. Operating Minima … 30 c. Instrumentally Derived RVR Limitations … 30 d. Non-Instrumentally Derived RVR Reports … 30 3-11. Runway Field Length Requirements and Runway Contamination … 30 a. AFM Landing Distance Data … 30 b. Wet Runway Considerations … 30 c. Use of Autobrakes … 30 d. Emergency Return After Takeoff … 30 e. Alternate Airport Field Length … 31 f. Acceptable Field Length Factors and Considerations … 31 3-12. Rollout Deceleration Systems or Procedures for CAT II and/or III … 32 a. Stopping Means … 32 b. Antiskid Systems … 32 3-13. Vision Systems … 33 a. Synthetic Vision Systems (SVS)/Enhanced Vision Systems (EVS)

Situation Awareness … 33 b. Synthetic Vision Guidance Systems (SVGS) … 33 c. Enhanced Flight Vision Systems … 33 3-14. Hybrid Systems … 33

CHAPTER 4. PROCEDURES … 35

4-1. Operational Procedures … 35 a. Application of AFM Provisions … 35 b. Crew Coordination … 35 c. Monitoring … 35 d. Use of the MDA, DA, DH, or AH … 35 e. CAT I, II, and III Flightcrew Procedures Compatibility … 36 f. Flightcrew Response to Non-Normal Events … 36 4-2. AWO Takeoff And CAT II/III Instrument Approach Procedures (IAP) … 36 a. Takeoff Guidance System Procedures … 36 b. Standard Obstacle Clearance for Approach and Missed Approach … 37 c. Special Obstacle Criteria … 37 d. Irregular Terrain Airports … 37 4-3. Continuing Approaches in Deteriorating Weather Conditions … 37 a. Approach Ban … 38 b. Wind Constraint Applicability … 38 4-4. Low-Visibility Taxi Procedures … 38 a. Low-Visibility Taxi Procedures … 38 b. Day/Night Provisions … 39 c. Electronic Presentations … 39 d. Surface Movement Guidance and Control System (SMGCS) … 39 4-5. Assesment of Threshold Crossing Height (TCH), Approach Descent Gradient, and Runway Slope … 39

Page vi

a. Operator Assessment … 39 b. Runway Characteristics … 39 c. Airport Layout Plan (ALP) … 39 4-6. Metric Altitudes … 39 4-7. Approach NAVAID Requirements … 39

CHAPTER 5. TRAINING AND CREW QUALIFICATION … 41

5-1. General … 41 a. Ground Training and Flight Training … 41 b. Terminal Instrument Procedures (TERPS) … 41 5-2. Training and Checking for CAT I Qualification … 41 5-3. Ground Training … 41 a. Ground Systems and NAVAIDs … 41 b. The Airborne System … 43 c. Flight Procedures and Associated Information … 44 5-4. Flight Training for AWO (Aircraft or FFS) … 46 a. Types of Procedures and Conditions to be Addressed … 46 b. Combining Multiple Requirements … 47 c. Maneuvers … 47 d. Addressing Applicable Regulations … 49 5-5. Initial Qualification … 49 a. Ground Training … 49 b. Flight Training … 49 5-6. Recurrent Qualification … 49 a. Recurrent Ground Training … 49 b. Recurrent Flight Training … 49 c. Qualification in Conjunction with AQP … 50 5-7. Requalification … 50 5-8. Transition Qualification … 51 5-9. Upgrade Qualification … 51 5-10. Flight Deck or Aircraft System Differences … 51 5-11. Recency of Experience … 51 a. Requirements … 51 b. Re-Establishing Recency of Experience … 51 5-12. Simultaneous Training for AWO … 51 5-13. Simultaneous Checking for AWO … 51 5-14. Checking for SA CAT I Qualification … 52 a. Additional SA CAT I Requirements … 52 b. Qualified CAT II Flightcrew Members … 52 5-15. Checking for CAT II Qualification … 52 5-16. Checking for CAT III Qualification … 53 a. Automatic Systems … 53 b. Manual Systems … 53 5-17. Checking for Low-Visibility Takeoff Qualification … 53 a. New/Reduced Minima … 53 b. No FFS Demonstration … 53

Page vii

5-18. Experience with Line Landings … 53 a. Automatic Systems … 53 b. Manual Systems … 53 5-19. Crew Records … 53 5-20. Dual Qualification … 54 a. Appropriate Training … 54 b. Program Approval … 54 5-21. Interchange … 54 5-22. AWO Training for Use of Foreign Airports … 54 5-23. Line Checks … 54 5-24. Special Procedures and/or Special Qualification Airports … 54 5-25. Particular Approach System/Procedure Qualification … 54 a. Aircraft Equipment Dependent Approach System Qualification … 54 b. Approach and Landing with an Engine Inoperative … 55 c. Circling Approaches … 55

CHAPTER 6. AIRPORTS, NAVIGATION FACILITIES, AND

METEOROLOGICAL CRITERIA … 57

6-1. Airport Authorization … 57 a. Authorized. U.S. and Non-U.S. Airports and Runways … 57 b. Authorization Requests … 57 6-2. Use of CAT I/II/III Navigation Facilities … 57 a. Standard CAT I/II/III Navigation Facilities … 57 b. Non-Standard CAT I/II/III Facilities … 57 6-3. Lighting Systems … 58 a. CAT I Lighting Systems … 58 b. CAT II/III Lighting Systems … 58 c. Surface Lighting Below Runway Visual Range (RVR) 1200 … 58 d. Lighting Systems for SA CAT I/II … 58 e. Lighting Exceptions … 58 6-4. Meteorological Services and RVR Availability and Use … 58 a. Meteorological Services … 58 b. RVR Availability and Use Requirements … 59 c. Pilot Assessment of Takeoff Visibility Equivalent to RVR … 60 d. Alternate RVR Requirements for Short Field Length Operations … 60 e. International RVR Reporting and Use Equivalence Considerations … 60 6-5. ILS Critical Area Protection … 61 6-6. Operational Facilities: Outages and Notices to Airmen (NOTAM) … 61 a. Outages … 61 b. Notices to Airmen … 61 6-7. Special Provisions for Facilities Used for Extended Operations (ETOPS) of Multi-Engine Aircraft or Alternates … 62 a. Airport Requirements … 62 b. Airport Information … 62 6-8. Alternate Minima … 62

Page viii

6-9. Flight Planning to Airports that Have Weather Conditions Below Landing Minima … 62

CHAPTER 7. CONTINUING AIRWORTHINESS/MAINTENANCE … 63

7-1. Maintenance Program General Provisions … 63 7-2. Maintenance Program Requirements … 63 a. AWO Operations … 63 b. Maintenance Program … 63 7-3. Initial and Recurrent Maintenance Training … 65 a. Training of Maintenance Personnel … 65 b. Training Requirements … 65 7-4. Test Equipment/Calibration Standards … 66 7-5. Return to Service Procedures … 66 a. Maintenance Procedures … 66 b. Testing … 66 c. Contract Maintenance … 67 7-6. Periodic Aircraft System Evaluations … 67 a. Evaluation Method … 67 b. Performance Evaluation … 67 c. FGS and/or Autoland System Checks … 67 7-7. Reliability Reporting and Quality Control … 67 a. Total Approaches … 67 b. Unsatisfactory Approaches … 67 c. Unscheduled Component Removals … 67 7-8. Configuration Control/System Modifications … 68 7-9. Records … 68 a. Operator Requirements … 68 b. Contract Maintenance Organization Requirements … 68 7-10. Part 129 Foreign Operator Maintenance Programs … 68 a. Maintenance of Part 129 Foreign Registered Aircraft … 68 b. Maintenance of Part 129 Foreign Operated U.S. N-Registered Aircraft … 68

CHAPTER 8. APPROVAL OF U.S. OPERATORS … 71

8-1. General … 71 8-2. Operations Manuals and Procedures … 71 a. Manuals … 71 b. Procedures … 71 8-3. Training Programs and Crew Qualification … 71 8-4. Dispatch Planning … 71 8-5. OpSpecs … 71 a. OpSpec Contents … 72 b. OpSpec Maintenance … 72 c. OpSpec Amendments … 72 8-6. Operational Demonstrations … 72 a. Aircraft System Suitability Demonstration … 72

Page ix

b. Operator Use Suitability Demonstration (OUSD) … 73 c. Use of Autoland or Head-Up Guidance at U.S. Type I Facilities

or Equivalent … 76 8-7. Determining the Proper OUSD for an Operator’s Requested Authorization … 77 a. Table Definitions … 77 b. Table Use … 78 c. Minimum Landings … 78 d. New Flight Control Equipment OUSD … 78 e. Six-Month Validation Phase Relief … 78 f. Small Fleet OUSD … 78 Table 8-1. Operator Use Suitability Demonstration Requirements … 79 8-8. CAT II/III Program Status Following Operator Acquisitions/Mergers … 80 8-9. Irregular Pre-Threshold Terrain and Other Restricted Runways … 80 8-10. U.S. Carrier AWO Operations at Foreign Airports … 80 a. Post-Approval Requirements … 80 b. Consistency with U.S. Standards … 80 8-11. Evaluation of New Technology and/or Operational Concepts … 80 a. New Technology Demonstration (NTD) Process … 80 b. NTD Methodology … 81 c. Process Illustration … 81 d. Conformity Inspections … 81 e. Post-NTD Operational Safety Assessment (OSA) or Review (OSR) … 81 f. Exclusive Benefit to Single Applicant … 81 g. Pre-Application or Advanced Research … 81 Figure 8-1. New Technology Demonstration Process … 83

CHAPTER 9. INTERNATIONAL (FOREIGN) OPERATORS CONDUCTING AWO AT

U.S AIRPORTS … 85

9-1. Acceptable Criteria … 85 a. Previously Approved Operators … 85 b. Airplane Flight Manual (AFM) Stated AWO Capability … 85 9-2. CAT II/III Authorization and Demonstrations … 85 a. Authorization … 85 b. Demonstration … 85 c. Addition of New Aircraft Type … 85 d. Additional Information … 85 9-3. Use of 14 CFR Non-Part 97 Procedures or Special Authorization (SA) Procedures … 86 a. Non-Part 97 Instrument Approach Procedures (IAP) … 86 b. Procedures Requiring SA … 86

CHAPTER 10. OPERATOR REPORTING AND TAKING CORRECTIVE ACTIONS … 87

10-1. Operator Reporting … 87 a. Standard AWO Performance Reporting … 87 b. Additional Reporting Requirements … 87

Page x

10-2. CAT II/III Operator Corrective Actions … 87 a. AWO Corrective Action Responsibility … 87 b. Example Corrective Actions … 87

APPENDIX 1. DEFINITIONS AND ACRONYMS (18 pages) … 1 APPENDIX 2. ENGINE INOPERATIVE CATEGORY (CAT) II/III

APPROACH OPERATIONS (6 pages) … 1 APPENDIX 3. STANDARD OPERATIONS/MANAGEMENT SPECIFICATIONS

(OPSPECS/MSPECS) AND LETTERS OF AUTHORIZATION (LOA) (8 pages) … 1 APPENDIX 4. IRREGULAR TERRAIN ASSESSMENT (6 pages) … 1

CHAPTER 1. INTRODUCTION

1-1. PURPOSE. This AC provides an acceptable means, but not the only means, for obtaining and maintaining authorization of operations in Category (CAT) I, CAT II, and CAT III landing weather minima and instrument flight rules (IFR) lower-than-standard takeoff minima. Terms used in this AC such as “should” or “must” are used only in the sense of ensuring applicability of these particular methods of compliance when the acceptable means of compliance described herein is used. This AC does not change, add, or delete regulatory requirements or authorize deviations from regulatory requirements. This AC addresses the operational authorizations formerly published in AC 120-28, Criteria for Approval of Category III Weather Minima for Takeoff, Landing, and Rollout, and AC 120-29, Criteria for Approval of Category I and Category II Weather Minima for Approach, and any subsequent developments.

1-1. PURPOSE. › e. CAT III Landing Minima. The CAT III landing minima at a particular…

a. Overview. This AC is the basis for AWO flight operations and should be used in conjunction with AC 20-191, which provides airworthiness criteria for aircraft system certification. Authorization for operators to act in compliance with their standard CAT II and III operations specifications (OpSpecs), management specifications (MSpecs), and letters of authorization (LOA) are also discussed at length in this AC.

b. Regulatory Basis. CAT II and III operations conducted by Title 14 of the Code of Federal Regulations (14 CFR) part 91 operators are done primarily in accordance with part 91, §§ 91.189, 91.191, 91.193, and part 91 appendix A, Category II Operations: Manual, Instruments, Equipment, and Maintenance; 14 CFR part 61, §§ 61.66, 61.67 and 61.68; and further provisions as authorized by the FAA Administrator in the operator’s LOA. Section 91.189(g) states that CAT II and III operations conducted by certificate holders operating under 14 CFR part 121, 125, 135, part 129 foreign air carriers, or holders of MSpecs issued in accordance with part 91 subpart K (91K), may conduct CAT II or CAT III operations only in accordance with their OpSpecs or MSpecs.

c. International Harmonization. This new AC also incorporates information pertaining to international AWO criteria harmonization between the Federal Aviation Administration (FAA), European Aviation Safety Agency (EASA), and several other regulatory authorities. Subsequent revisions of this AC will be published as additional AWO harmonization items are agreed upon by FAA, EASA, and other regulatory authorities.

d. Nomenclature Changes. This AC reflects the changes which occurred in 2011 when the FAA removed the definitions of CAT IIIa, IIIb, and IIIc operations and discontinued the use of this nomenclature in subsequent documentation. Some FAA instrument procedures may still retain CAT IIIa nomenclature until these procedures are updated or amended. These definitions are outdated and no longer utilized for aircraft certification or operational authorization. Any references to these terms in this AC are used for historical context.

e. CAT III Landing Minima. The CAT III landing minima at a particular runway are currently based on the demonstrated qualities and capabilities of the signal utilized for approach on that runway. The approach charts now show only the lowest possible CAT III landing minima on a runway. For example, the approach chart for a landing at an airport may only state that the Runway Visual Range (RVR) is 600 and will not make any reference to the CAT IIIb operations

CHAPTER 1. INTRODUCTION › 1-5. EXPLANATION OF CONTENT.

definition. Operators now use the published minima in conjunction with their OpSpecs/MSpec to determine the lowest landing minima allowed to them.

f. All Weather Operations. The term AWO, as used in this AC, is meant to include operations during low-visibility takeoff and landing conditions. This encompasses takeoff below standard weather minima and instrument approach procedures (IAP) for CAT I, II and III, to include Special Authorization (SA) CAT I and II.

g. Responsible Flight Standards Office. There are numerous instances in this AC where the term “responsible Flight Standards office” is used. The intent of this phrase is to direct the operator to the proper office/organization with authorization authority based upon the type of operation referenced.

h. Dispatcher. For the purposes of this document, the term “dispatcher” refers to a person or persons exercising operational control over a flight other than the flightcrew.

1-2. WHERE YOU CAN FIND THIS AC. You can find this AC on the FAA’s website at http://www.faa.gov/regulations_policies/advisory_circulars.

1-3. RELATIONSHIP OF THIS AC WITH AC 20-191 AND THEIR IMPACT UPON AC 120-29A AND AC 120-28D. This AC contains the revised operational authorization information previously found in AC 120-28D, Criteria for Approval of Category III Weather Minima for Takeoff, Landing, And Rollout, dated July 13, 1999, and AC 120-29A, Criteria for Approval of Category I and Category II Weather Minima for Approach, dated August 12, 2002. Prior to the publication of this AC, operational authorization and aircraft certification information was consolidated in either AC 120-29A (for CAT I and II), or AC 120-28D (for CAT III).

Aircraft certification information currently contained in AC 120-28D and AC 120-29A remains in effect until revised by the publication of AC 20-191. The publication of AC 20-191 will subsequently cancel AC 120-28D and AC 120-29A.

1-4. APPLICABILITY. The intent of this AC is to provide information for all operators, including part 91, considering or currently operating under AWO. New operational authorizations (e.g., C052, C060, C078, etc.) should use the criteria of this AC. Operations approved based upon earlier criteria may continue or operators may seek additional operational credit provided by this AC. Airworthiness criteria and demonstrations are addressed in AC 20-191.

1-5. EXPLANATION OF CONTENT. The AC includes incorporation and significant revision of information previously contained in AC 120-29 and AC 120-28 into a single document, the extraction of airworthiness criteria and relocation into AC 20-191, and the removal of information pertaining to Required Navigation Performance (RNP) and microwave landing system (MLS). Many changes to the content of those previous ACs have been made to improve clarity, accuracy, completeness, and consistency. It is suggested that this AC be read in its entirety due to the new presentation of this subject matter.

1-5. EXPLANATION OF CONTENT. › e. Satellite-Based Augmentation System (SBAS). This AC does not discuss…

a. Takeoff, Approach, Landing, and Rollout Operations. This new AC discusses takeoff, approach, landing, and rollout operations which involve ground-based Navigational Aids (NAVAID) used for AWO approach operations. The AC includes information on AWO takeoff guidance systems, expanded SA CAT I guidance, updated CAT II/III guidance for use in conjunction with Head-Up Display (HUD) systems, Ground Based Augmentation System (GBAS) Landing System (GLS), and use of CAT II/III during certain engine inoperative operations.

b. Enhanced Flight Vision Systems (EFVS) and Synthetic Vision Guidance Systems (SVGS). Additional information is included addressing operations utilizing EFVS and SVGS during AWO operations, as well as operations involving hybrid approach and landing systems. Expanded information and guidance on EFVS and its authorized use are located in AC 90-106, Enhanced Flight Vision Systems. The EFVS rule, § 91.176, effective March 21, 2017, and associated EFVS operational authorizations (e.g., OpSpecs) contain unique operational capabilities and regulatory exceptions that are not addressed in this document. Readers must refer to AC 90-106 for a complete understanding of differences which may apply when conducting EFVS operations or using EFVS during conduct of operations discussed in this AC (e.g., CAT II or III operations).

c. New Technology Demonstration (NTD). A new term, NTD, is introduced in this AC as a process of generic demonstration of technology, providing an equivalent or acceptable level of safety to the current operation. The NTD was formerly known as Proof of Concept (PoC) in AC 120-28 and AC 120-29. An NTD is typically initiated by an operator or manufacturer after consultation with the Flight Technologies and Procedures Division.

d. Operator Use Suitability Demonstration (OUSD) Changes. Changes to the topic of OUSD are also contained in this AC. Operators should pay particular attention to several updated minimum requirements for demonstration of appropriate performance, automation, and technology involved in an acceptable OUSD. Changes to the equipage, training, and maintenance requirements for SA CAT I authorization and operations are included in this new AC. Finally, steep angle approach operational approval is examined and authority for operational authorization is established.

e. Satellite-Based Augmentation System (SBAS). This AC does not discuss operations based upon SBAS. Operations relating to this subject are discussed in the most current versions of AC 90-101, Approval Guidance for RNP Procedures with AR, AC 90-105, Approval Guidance for RNP Operations and Barometric Vertical Navigation in the U.S. National Airspace System and in Oceanic and Remote Continental Airspace, AC 90-107, Guidance for Localizer Performance with Vertical Guidance and Localizer Performance without Vertical Guidance Approach Operations in the U.S. National Airspace System and AC 90-108, Use of Suitable Area Navigation (RNAV) Systems on Conventional Routes and Procedures.

b. ACs, FAA Orders, and Operational Authorizations. Unless a specific… › (1) ACs:

1-6. RELATED REGULATIONS AND REFERENCES.

a. Title 14 CFR:

• Part 23, § 23.2510. • Part 25, §§ 25.1309, 25.1322, 25.1329, 25.1581 and 25.1583. • Part 61, §§ 61.21 and 61.66. • Part 91, §§ 91.175, 91.176, 91.189, 91.191, 91.193 and Appendix A. • Part 121, §§ 121.579 and 121.651. • Part 125, §§ 125.379 and 125.381. • Part 129, § 129.11. • Part 135, § 135.225.

b. ACs, FAA Orders, and Operational Authorizations. Unless a specific reference is made to a particular version of a rule or AC, current editions of the following FAA orders, operational authorizations, and ACs should be used:

(1) ACs:

• AC 20-153, Acceptance of Aeronautical Data Processes and Associated Databases. • AC 20-185, Airworthiness Approval of Synthetic Vision Guidance System. • AC 25-7, Flight Test Guide for Certification of Transport Category Airplanes. • AC 25-31, Takeoff Performance Data for Operations on Contaminated Runways. • AC 25-32, Landing Performance Data for Time-of-Arrival Landing Performance Assessments. • AC 90-101, Approval Guidance for RNP Procedures with AR. • AC 90-105, Approval Guidance for RNP Operations and Barometric Vertical Navigation in the U.S. National Airspace System and in Oceanic and Remote Continental Airspace. • AC 90-106, Enhanced Flight Vision Systems. • AC 90-107, Guidance for Localizer Performance with Vertical Guidance and Localizer Performance without Vertical Guidance Approach Operations in the U.S. National Airspace System. • AC 90-108, Use of Suitable Area Navigation (RNAV) Systems on Conventional Routes and Procedures. • AC 90-112, Development and Submission of Special Instrument Procedures to the FAA. • AC 91-79, Mitigating the Risks of a Runway Overrun Upon Landing. • AC 120-53, Guidance for Conducting and Use of Flight Standardization Board Evaluations. • AC 20-191, Criteria for Airworthiness Approval of Low Visibility Takeoff and CAT II/III Approaches. • AC 120-57, Surface Movement Guidance and Control System. • AC 120-62, Takeoff Safety Training Aid.

1-6. RELATED REGULATIONS AND REFERENCES. › c. OpSpecs/MSpecs/LOAs:

• AC 120-71, Standard Operating Procedures and Pilot Monitoring Duties for Flight Deck Crewmembers. • AC 120-76, Guidelines for the Certification, Airworthiness, and Operational Use of Electronic Flight Bags. • AC 120-91, Airport Obstacle Analysis. • AC 120-105, Foreign Terminal Instrument Procedures (FTIP) Acceptance/Review. • AC 121.195-1, Operational Landing Distances for Wet Runways; Transport Category Airplanes.

(2) FAA Orders:

• FAA Order 8400.13, Procedures for the Evaluation and Approval of Facilities for Special Authorization Category I Operations and All Category II and III Operations. • FAA Order 8900.1, Flight Standards Information Management System (FSIMS). • FAA Order 6750.16, Siting Criteria for Instrument Landing Systems. • FAA Order 6750.24, Instrument Landing System and Ancillary Electronic Component Configuration and Performance Requirements. • FAA Order JO 7110.65, Air Traffic Control. • FAA Order 8260.3, United States Standard for Terminal Instrument Procedures (TERPS). • FAA Order 8260.60, Special Instrument Procedures. • RTCA DO-253, Minimum Operational Performance Standards for GPS Local Area Augmentation System Airborne Equipment. • RTCA DO-359, Minimum Aviation System Performance Standards (MASPS) for Synthetic Vision Guidance Systems.

c. OpSpecs/MSpecs/LOAs:

• Standard OpSpecs Parts A and C. • OpSpec C048, Enhanced Flight Vision System Operations. • OpSpec/MSpec/LOA C051, Terminal Instrument Procedures. • OpSpec C052, Straight-in Non-Precision, APV, and Category I Precision Approach and Landing Minima—All Airports. • OpSpec C055, Alternate Airport IFR Weather Minimums. • OpSpec C056, IFR Takeoff Minimums, Airplane Operations—All Airports. • OpSpec C057, IFR Takeoff Minimums, 14 CFR Part 135 Airplane Operations—All Airports. • OpSpec C060, Category II and Category III Instrument Approach and Landing Operations. • OpSpec C061, Flight Control Guidance Systems for Automatic Landing Operations Other Than Categories II and III.

• OpSpec C062, Manually Flown Flight Control Guidance System Certified for Landing Operations Other Than Categories II and III. • OpSpec C078, IFR Lower Than Standard Takeoff Minima, Airplane Operations— All Airports. • OpSpec C079, IFR Lower Than Standard Takeoff Minima, 14 CFR Part 135 Airplane Operations—All Airports. • OpSpec D072, Aircraft Maintenance – Continuous Airworthiness Maintenance Program (CAMP) Authorization.

CHAPTER 2. BACKGROUND › 2-3. APPROACH TERMINOLOGY.

Par 2-1 Page 7 (and 8)

CHAPTER 2. BACKGROUND

2-1. OPERATIONAL AUTHORIZATIONS VERSUS AIRWORTHINESS DEMONSTRATIONS. Takeoff and approach weather minima are approved through applicable operating rules, use of approved instrument procedures, and issuance of operations specifications (OpSpecs), management specifications (MSpecs), and letters of authorization (LOA). Airworthiness demonstration of aircraft equipment is usually accomplished on a one-time basis at the time of type certification (TC) or Supplemental Type Certification (STC). This demonstration is based upon the airworthiness criteria in place at that time. Since operating rules may change after airworthiness demonstrations are conducted, additional operational credit may be applied. In general, information related to operational approvals is contained in the main body of this AC and criteria related primarily to the airworthiness demonstration of systems or equipment is contained in AC 20-191.

2-2. EXPLANATION OF TERMS. A comprehensive list of definitions pertinent to this AC is included in Appendix 1. Within this AC, RVR values are specified in units of feet unless otherwise noted. A conversion table may be found in OpSpec C051. Minima typically used during LVO are provided in the appropriate OpSpecs.

2-3. APPROACH TERMINOLOGY. Terminology used in this AC is consistent with current OpSpecs, MSpecs, and LOAs. Definitions of instrument approach categories are listed in Appendix 1, Definitions and Acronyms. While there are slight variations of these definitions as used within International Civil Aviation Organization (ICAO) and various countries internationally, the broad objectives and practical operational applications are similar. Also, in certain states, lowest authorized minima may be slightly different than as specified by the U.S. or ICAO criteria. The definitions used in standard OpSpecs, where different from ICAO, apply and take precedence for U.S. operators or for international operators conducting operations within the United States or at U.S. facilities.

b. Magnetic Variation (MagVar) Data and Onboard Database. Issues with… › (2) The MagVar update is generally only critical for CAT II/III…

CHAPTER 3. OPERATIONAL CONCEPTS

3-1. INSTRUMENT OPERATIONS. This AC addresses operational authorization for terminal instrument operations using ground-based Navigational Aids (NAVAID) or space-based NAVAIDs augmented by ground-based equipment. These operations include takeoff in lower-than-standard visibility conditions, Category (CAT) I, CAT I Landing Minima with Reduced Lighting (Runway Visual Range (RVR) 1800), Special Authorization (SA) CAT I, CAT II, SA CAT II, and CAT III. Some of these operations require special aircrew and aircraft certification. These operations are collectively referred to as AWO throughout the course of this document.

a. Airborne Systems. Basic airworthiness certification for instrument flight rules (IFR) is typically considered acceptable for operational approval of an aircraft for standard CAT I. However, CAT II and III airborne system requirements, as well as those for takeoff guidance systems used for lower-than-standard minima, are specified in AC 20-191. Airborne systems intended to meet CAT I Landing Minima with Reduced Lighting (RVR 1800) and SA CAT I/II requirements, while not addressed in AC 20-191, are specified in paragraph 3-7 below.

(1) For aircraft intended for AWO operations and previously approved using AC 120-29 and/or AC 120-28, the airworthiness criteria for airborne systems specified in the approved Airplane Flight Manual (AFM) are still valid.

(2) Airborne equipment listed in AC 20-191 must be operative in accordance with provisions of applicable standard operations specifications (OpSpecs). Airframe manufacturers and individual operators may also include other optional equipment as part of the CAT II/III configuration; however, that equipment does not need to be operative to conduct a CAT II/III approach unless required by that operator's OpSpecs and consistent with the FAA-approved minimum equipment list (MEL).

b. Magnetic Variation (MagVar) Data and Onboard Database. Issues with MagVar primarily occur when the MagVar data being used internally in the aircraft is not close enough to the current MagVar at a location, or when it is not close enough to the MagVar used in the approach procedure.

(1) Some avionics convert true heading references to magnetic heading references by using worldwide MagVar data contained in an onboard database. Algorithms convert the data into a specific magnetic heading reference for a specific geographic reference point. However, since the Earth’s magnetic fields constantly change, MagVar databases need periodic updates to provide accurate magnetic heading references. The National Oceanic and Atmospheric Administration (NOAA) offers a World Magnetic Model available at http://www.ngdc.noaa.gov/geomag/geomag.shtml. This product is one acceptable source for MagVar information.

(2) The MagVar update is generally only critical for CAT II/III operations, coupled approach, and practice autoland CAT I operations. When flying these procedures, the aircraft systems construct a track in True, used for guidance during rollout and as a cross check on final, apply MagVar from the onboard source(s), and compare the resulting magnetic course to the

b. Magnetic Variation (MagVar) Data and Onboard Database. Issues with… › (6) In some instances, Notices to Airmen (NOTAM) may contain MagVar…

published Final Approach Course (FAC). If the difference is greater than some predetermined value (typically three or four degrees) the system may flag or disengage the autopilot. The difference between the onboard source and the published procedure may be in the opposite direction from the current MagVar at the location, one leading and one lagging. Therefore, the total amount of difference must be considered, not just the difference from the current local MagVar.

(3) Aircraft design approval holders should identify any operating limitations of their aircraft associated with application of the MagVar data to ensure sufficiently accurate magnetic heading references are presented and used in the aircraft. Consider at least the following in determining the operating limitations: the error characteristics of magnetic heading references, especially where local magnetic anomalies occur or in regions of high magnetic field inclination or high secular rates of change; intended operation (instrument landing system (ILS) approach, automatic landing, en route navigation, display of course/track to the pilot, etc.); errors in the magnetic reference of any radio navigation aid used; and/or the accuracy of the magnetic reference of the procedure. Operational limitations need to be re-evaluated commensurate with the intended use and the dynamics of error associated with the magnetic heading reference. Conditions under which operations do not meet the intended function must be clearly identified.

(4) Avionics may use values other than the Localizer (LOC) MagVar, such as the aerodrome magnetic or the on aerodrome NAVAID, or a calculated value, as the onboard source. Also, some aircraft have more than one onboard source of MagVar data, which may cause an internal MagVar disagreement when one database is updated and the other is not. This internal disagreement may cause flags and disconnects. Some aircraft seem to experience problems only when there is a strong crosswind. The MagVar on the aerodrome diagram is not related to instrument procedures, and is updated on a different schedule. Therefore, it should not be used in any determination of coupled approach and autoland capability.

(5) While issues with MagVar have occurred mostly at aerodromes with a high rate of change, most of which are located at higher latitudes, they can occur at any location where the onboard MagVar data and the published procedures are further apart than the avionics tolerance. Operators should consult manufacturer guidance concerning the onboard MagVar database and its suitability for autoflight and autoland at aerodromes they intend to operate. The aircraft design approval holders’ continuing airworthiness requirements must define the conditions under which the MagVar database and, if applicable, conversion algorithms or hardware, must be updated. This could be contained in a periodic airplane flight manual update or other Original Equipment Manufacturer (OEM) documentation. These requirements should also define the maintenance procedures necessary to update the onboard MagVar database for their avionics.

(6) In some instances, Notices to Airmen (NOTAM) may contain MagVar restrictions. A change in the ILS procedure or aerodrome MagVar should be evaluated to determine whether autoflight is still supported with the current onboard MagVar data. Also, updating the onboard data may cause issues at an aerodrome where the procedure MagVar has not been updated. When conducting autoflight and autoland operations at any new aerodrome, it is therefore imperative that flightcrews should use caution. Company/operator training and procedures should adequately cover this potential issue.

b. Pilot Assessment of Equivalent RVR. For takeoff circumstances where… › (1) To be eligible to use this provision, the operator must ensure that…

c. Airborne Databases and Interface. It is highly recommended that all airborne databases (e.g., Terrain Awareness and Warning System (TAWS), Enhanced Ground Proximity Warning System (EGPWS), Synthetic Vision Guidance System (SVGS)) be current with the intended area of operation for AWO operations. Terrain, runway, and obstacle database requirements must support the intended function. Valid and compatible databases for SVGS must be installed and contain current data. Refer to AC 20-153 for guidance on the importance of database currency and integrity. Additionally, to ensure continued airworthiness and nuisance-free operation, airborne equipment used for approach operations should be compatible with systems using airborne databases.

3-2. TAKEOFF.

a. Takeoff Minima. Takeoff minima are addressed by §§ 91.175(f), 91.1039; §§ 121.649, 121.651; 125.381; § 135.225 and standard OpSpecs; MSpecs and/or letters of authorization (LOA).

(1) When lower-than-standard minima are necessary, applicable criteria for use of those OpSpec minima are specified in this AC. When appropriate, principal operations inspectors (POI) issue OpSpecs specifying the lower minima through paragraph C056 and C078 for part 121 and 125 operators and OpSpecs paragraphs C057 and C079 for part 135 operators. OpSpecs specifying the lower minima through paragraph C056 may be issued to part 129 operators. OpSpecs/MSpecs or LOAs contain specific guidance regarding pilots, aircraft, and airports when lower-than-standard takeoff minima are used. Authorization of takeoff minima below the level supported by use of visual reference alone requires the use of a guidance system that has been demonstrated to provide an acceptable level of performance and satisfactory workload for the minima approved, with or without the use of visual reference. The performance and workload assessment of such a system must have considered any compensation that may be introduced by the pilot for particular guidance system characteristics (e.g., coping with a slight LOC signal offset during initial runway alignment) or concurrent use of the guidance system with limited or patchy visual references.

(2) Provisions for demonstration of systems eligible for takeoff minima below the level supported by use of visual reference alone may be found in AC 20-191.

(3) An NTD is necessary for initial authorization of takeoff minima less than RVR 300.

b. Pilot Assessment of Equivalent RVR. For takeoff circumstances where touchdown zone (TDZ) RVR is inoperative or is determined by the pilot to be significantly in error (e.g., patchy fog obscuring an RVR Visibility Sensor (VS) but not the runway, snow on transmissometer causing erroneous readings), operators may be authorized to make a pilot assessment in lieu of RVR (see subparagraph 6-4c.).

(1) To be eligible to use this provision, the operator must ensure that each pilot authorized to make this determination has completed approved training addressing pilot procedures to be used for visibility assessment in lieu of RVR, and the pilot can determine the necessary runway markings or runway lighting that must be available to provide an equivalent RVR to that which is specified to ensure adequate visual reference for the takeoff.

a. Approach and Landing Concepts. › (6) Additional demonstration or operational assessment beyond that…

(2) When any pilot assessment of equivalent RVR is made, the pilot must be able to positively determine position on the airport, the correct runway, and positively establish that the aircraft is at the correct position for initiation of takeoff. A pilot may assess visibility at the takeoff position in lieu of reported TDZ RVR (or equivalent) in accordance with OpSpec C078/C079 and subparagraph 6-4c.

3-3. LANDING.

a. Approach and Landing Concepts.

(1) CAT I operations are considered to be any Standard Instrument Approach Procedure (SIAP) with a decision altitude (DA) or minimum descent altitude (MDA) greater than or equal to 200 feet height above touchdown (HAT) and a visibility requirement greater than or equal to RVR 1800.

NOTE: With SA, CAT I minima below RVR 1800 and 200 feet HAT may be authorized via OpSpec, MSpec, or LOA (See subparagraph (4) below).

NOTE: For enhanced flight vision system (EFVS) considerations during CAT I approach operations to reduced visibilities, refer to AC 90-106.

(2) CAT II operations are considered to be any SIAP with a DA/decision height (DH) or visibility requirement less than that specified for CAT I, but greater than or equal to 100 feet HAT and RVR 1000.

(3) CAT III operations are considered to be any SIAP with a DH less than that specified for CAT II (or with no DH, or with an Alert Height (AH)) and a visibility less than that specified for CAT II).

(4) SA CAT I/II operations described in this AC are considered nonstandard with respect to minima historically associated with their approach category. These operations may require additional aircraft equipment and aircrew qualifications, and may allow the use of runways with less than the normal lighting facilities required for their approach category. (See subparagraphs 3-7e and f for further guidance).

(5) CAT II operations are restricted by standard OpSpec C060 authorizations to be flown using a Head-Up Display (HUD), an autopilot coupled to DH, or an autoland system. However, if an operator of aircraft with advanced approach and landing systems desires the option of flying a manual approach using head-down guidance (e.g., flight director (F/D)), nonstandard OpSpec language authorizing this is required and additional operating restrictions and pilot training may be required.

(6) Additional demonstration or operational assessment beyond that required for basic IFR flight, under provisions of basic aircraft part 25, typically is necessary for operational authorization of an aircraft for CAT II/III. For CAT II/III minima, certain non-normal conditions are typically considered in the assessment and authorization process. Response to those non-normal conditions may be explicitly defined in the CAT II/III authorization (e.g., electrical component failure or engine inoperative CAT II/III). For failures other than those addressed by

c. Considerations for the Use of Procedures Other Than U.S. Standard… › (8) Availability of Aeronautical Information (AI) (e.g., timely NOTAM…

the CAT II/III authorization, the pilot or operator may need to adjust the operating minima used, introduce wind limit constraints, or address other factors to ensure safe operation for the particular non-normal condition. Specific criteria for airworthiness demonstration of systems or capabilities for CAT II/III are included in AC 20-191.

b. Acceptable Instrument Approach Procedure (IAP) Basis. IAPs used by operators in accordance with this AC should be based on:

(1) U.S. SIAPs (i.e., 14 CFR part 97 instrument procedures designed to conform to Order 8260.3 and other related 8260 series orders).

(2) For non-U.S. airports, foreign IAPs acceptable to FAA promulgated by the state of the airport of landing (i.e., International Civil Aviation Organization (ICAO), State of the Aerodrome). Refer to AC 120-105.

(3) Terminal IAPs at U.S. Military airports, regardless of their physical location (e.g. Ramstein Air Base in Germany), when authorized by the Department of Defense (DOD) and the terminal instrument procedure are constructed using criteria based on Order 8260.3; ICAO Document 8168-OPS, Procedures for Air Navigation Services—Aircraft Operations (PANS-OPS), Volume II; or Military Instrument Procedures Standardization (MIPS); or other special criteria approved by the Flight Technologies and Procedures Division.

(4) Special IAPs developed and approved by the FAA.

(5) Special IAPs developed by an FAA-approved third party and approved by FAA.

c. Considerations for the Use of Procedures Other Than U.S. Standard Procedures. For procedures other than those developed in accordance with Order 8260.3 or other pertinent FAA 8260 series orders, the operator must ensure consideration of at least the following factors related to use of those instrument procedures:

(1) Availability of suitable weather reporting and forecasts;

(2) Identification of any necessary alternate airports or alternate minima;

(3) Ability to discontinue an approach from any point to touchdown;

(4) Suitability of the airborne equipment to use the procedure (e.g., compatibility of the airborne equipment with the type/characteristics of the navigation facilities used);

(5) Suitability of ground systems/equipment (e.g., lighting, RVR sensors, and pilot control of lighting);

(6) Suitability of NAVAIDs (e.g., maintenance and monitoring);

(7) Suitability of airport/runway (e.g., obstructions, clear zones, and markings);

(8) Availability of Aeronautical Information (AI) (e.g., timely NOTAM availability);

*USAF/USN CAT E maximum is 3.50 › f. Steep Angle Approach. A procedure with a GPA or VDA at or above 4.5…

(9) Identification of any special training or qualification related to the procedure; and

(10) Resolution of any issues identified from adverse “service experience” with the procedure.

d. Special IAPs. Special procedures are approved by the Flight Technologies and Procedures Division and issued/authorized by the POI after coordination with pertinent FAA organizations (refer to AC 90-112). Operator requests for the use of special procedures should be coordinated by the POI with the Flight Standards office having responsibility for the airport of the procedure. If applicable, these special procedures should address any provisions associated with application of § 121.445 for special airport qualification.

e. Glide Path Angle (GPA) and Vertical Descent Angle (VDA). Operators must consult the FAA-approved AFM for aircraft limitations which may apply to use of GPAs and/or VDAs other than standard.

(1) CAT I straight-in approaches are normally constructed with a standard GPA or VDA of 3.0° whenever practical. Standard GPAs should not be less than 3.0° and should not exceed the values stipulated in Table 3-1, Maximum Standard Approach Design Glide Path Angles/Vertical Descent Angles. Standard VDAs should not be less than 2.75° and should not exceed the values stipulated in Table 3-1.

TABLE 3-1. MAXIMUM STANDARD APPROACH DESIGN GLIDE PATH

ANGLES/VERTICAL DESCENT ANGLES

CAT Maximum Angle

A (80 knots or less) 6.40

A (81-90 knots) 5.70

B 4.20

C 3.77

D 3.50

E 3.10* *USAF/USN CAT E maximum is 3.50°

(2) SA CAT I/II and CAT II/III approaches are constructed with a standard GPA of 3.0°. U.S. domestic approach angles for SA CAT I/II and CAT II/III approaches other than 3.0° require approval of the Flight Technologies and Procedures Division.

f. Steep Angle Approach. A procedure with a GPA or VDA at or above 4.5° is considered to be a steep angle approach for operations using transport category airplanes. Refer to AC 25-7 for detailed guidance on required certification and AFM documentation. The use of any steep approach will require specific AFM supplemental information including operational procedures and restrictions, any limitations, airplane configurations (e.g., flaps, gear, inoperative engines, etc.), performance information, as well as any flightcrew training necessary.

3-6. REQUIREMENTS FOR CAT I OPERATIONS. › b. CAT I Landing Minima with Reduced Lighting (RVR 1800). These…

Historically, some airport authorities may also require a letter of written approval from the certificating body. Authorization will be required for the use of a non-part 97 or non-PANS-OPS procedure (refer to Order 8260.60 and AC 90-112). Contact the responsible Flight Standards office for further guidance.

3-4. ENGINE INOPERATIVE CAT II/III. See Appendix 2, Engine Inoperative Category (CAT) II/III Approach Operations.

3-5. GO-AROUND SAFETY. A multiengine aircraft conducting an instrument approach should be capable of safely executing a go-around from any point on an approach prior to touchdown with the aircraft in both normal and specified non-normal configurations (e.g., engine out). This capability is necessary to provide for go-around safety due to missed approaches or rejected landings for a variety of circumstances.

a. CAT I Go-Around. Pilots must be aware that after the aircraft has passed the DA/DH or missed approach point (MAP), the published missed approach does not guarantee standard missed approach obstacle clearance. Pilot preplanning for such non-normal events is discussed further in the Aeronautical Information Manual (AIM).

b. CAT II/III Go-Around. The evaluation of this capability is based on normal or specified non-normal CAT III operations at the lowest controlling RVR authorized. This should account for factors related to geometric limitations during the transition to go-around, limited visual cues, autopilot mode switching, and other pertinent factors. For aircraft in which a go-around from a very low altitude may result in touchdown, the safety of such a procedure should be established considering its effect on related systems. This includes operation of auto spoilers, automatic braking systems, autopilot mode switching, auto-throttle mode, reverse thrust initiation, and other systems affected by a low altitude go-around. Except for failure conditions shown to be extremely improbable, a safe go-around must be possible from any point on the approach.

c. Automatic Go-Around. If an automatic go-around capability is provided, it should be demonstrated that a go-around can be safely initiated and completed from any point on an approach prior to touchdown. If the automatic go-around mode can be engaged at or after touchdown, it should be shown to be safe. The ability to initiate an automatic go-around at or after touchdown is not required.

3-6. REQUIREMENTS FOR CAT I OPERATIONS.

a. General Requirements. In general, authorization for standard CAT I operations do not require airworthiness, maintenance, equipage, qualification, or training provisions beyond those required for basic IFR operations under the appropriate 14 CFR part (e.g. part 91, 121) and appropriate for the type of operation being flown. However, parts 121, 125, 129, and 135 operators may only conduct CAT I instrument approaches in accordance with the minima and procedures set forth in their OpSpecs, which should be completed in accordance with Chapter 8 and/or Chapter 9.

b. CAT I Landing Minima with Reduced Lighting (RVR 1800). These operations differ from standard CAT I by allowing for reduced runway lighting requirements (CL and TDZ lights

not required), mitigated by the use of additional onboard equipment. Along with any applicable equipment otherwise specified for CAT I, these operations require an F/D, autopilot, or HUD approved for at least CAT I. The equipment used must provide course and glide path guidance to the DA or until initiation of a missed approach. When authorized by an OpSpec, commercial operators may conduct these operations where designated by a note on a SIAP or on regular RVR 1800 approaches when installed CL and/or TDZ lighting is inoperative. Commercial single-pilot operations are prohibited from using the F/D to conduct these operations without the accompanying use of an AP or HUD.

3-7. REQUIREMENTS FOR OPERATIONS BELOW RVR 1800 TO 1000. › d. Use of IM. Use of the IM or approved substitute may be authorized in…

3-7. REQUIREMENTS FOR OPERATIONS BELOW RVR 1800 TO 1000.

a. General Requirements.

(1) Flightcrew training and qualification consistent with provisions of Chapter 5 for these operations have been completed;

(2) Appropriate NAVAIDs and airport/lighting facilities for the procedures to be flown should be consistent with Chapter 6 of this AC;

(3) With the exception of SA CAT I-only operations, an acceptable continuing airworthiness/maintenance program for the airborne system is provided in accordance with Chapter 7; and

(4) An operational authorization has been completed in accordance with Chapter 8 for a U.S. operator or Chapter 9 for a non-U.S. operator.

NOTE: See Table 3-2, Special Authorization Category II and Category II Minima Matrix, for associated approach RVR minima.

b. Specification of CAT II DA/DH. The lowest authorized DA/DH is cited in this paragraph as an equivalent DH related to height above TDZ elevation (e.g., HAT value of 100 feet). This is done even though operational minima for these operations are typically specified as an equivalent DH value based on radio altitude height above the underlying approach terrain. While a DA is conceptually not precluded for use with CAT II, DAs are not routinely used for these operations, except as a backup for inner marker (IM)-based minima when irregular terrain precludes reliable radio altimeter use to determine minima.

c. Eligibility for CAT II Minima Not Less Than 100 Feet DA/DH. Instrument approach operations that may be authorized CAT II minima currently include only ILS. The FAA may authorize CAT II operations based on Ground Based Augmentation System (GBAS) Landing System (GLS) at a future date.

d. Use of IM. Use of the IM or approved substitute may be authorized in lieu of a DA/DH. An IM is typically used at runways designated by the applicable procedure, such as where radio altimeter (RA) use is limited or Not Authorized (NA) due to irregular underlying terrain (e.g., RA NA).

(d) A suitable manual or automatic flight guidance system (FGS)… › 1. Manual FGSs must provide each pilot with course and glide path…

e. SA CAT I. SA CAT I differs from standard CAT I by allowing for reduced runway lighting and RVR requirements while lowering the DA/DH, offset by the use of additional onboard equipment. The SA CAT I approach procedure has a visibility minimum as low as RVR 1400 and a DH as low as 150 feet HAT therefore requiring the use of radio altimeter (RA) minima or approved substitute. Minimum required lighting includes a medium intensity Approach Light System (ALS) with runway alignment indicator lights (RAIL) (MALSR) or better ALS (i.e., ALSF or simplified short ALS with RAIL (SSALR)) and High Intensity Runway Lights (HIRL) on the runway. TDZ and runway CL lights are not required. Refer to Order 8400.13 for additional information on airfield infrastructure requirements (i.e., lighting, power, air traffic control, etc.) if required. A single RVR system in the TDZ is also sufficient. SA CAT I requires less runway lighting, approach lighting, and RVR reporting than would normally be required for approach operations at this low visibility, but requires a higher level of aircraft capability than is normally necessary for a CAT I operation. Operators are approved for this operation by the appropriate OpSpec/management specification (MSpec) or LOA. Single-pilot operations are prohibited from using SA CAT I landing minima.

(1) Visual references required for approved SA CAT I operations are discussed below in subparagraph 3-7i(2).

(2) Future use of navigation signals other than ILS for SA CAT I operations (e.g., GLS) may require further evaluation of signal suitability and airborne system compatibility via approved New Technology Demonstration (NTD).

(3) The following, along with any applicable equipment otherwise specified for CAT I, is the minimum aircraft equipment considered necessary for an authorization for SA CAT I:

(a) Two independent navigation receivers, or equivalent, of each type intended for use.

(b) A radio altimeter is required. Two independent radio altimeters are recommended. A certified substitute for the radio altimeter may be approved in coordination with the Flight Technologies and Procedures Division.

(c) Rain removal equipment for each pilot (e.g., windshield wiper, bleed air, and rain repellant).

(d) A suitable manual or automatic flight guidance system (FGS) certified and maintained to support a DH of 150 feet or lower. This system will contain the following attributes in a manner acceptable to the FAA:

1. Manual FGSs must provide each pilot with course and glide path command guidance to the DH, while simultaneously providing the pilot flying (PF) with a continuous indication of the desired trajectory to the runway TDZ independent of the guidance used for the approach. The guidance system must also provide the PF with dynamic perception of aircraft position relative to the TDZ of the runway of intended landing in order to facilitate the transition to the visual segment of the approach by reducing the time needed for the acquisition of visual cues. An aircraft type and/or system previously approved for SA CAT I, based upon HUD equipment, is considered to meet the requirements of this paragraph.

3-7. REQUIREMENTS FOR OPERATIONS BELOW RVR 1800 TO 1000. › g. CAT II Using RVR 1000 Minima. CAT II using RVR 1000 minima may be…

2. Automatic FGSs certified for CAT II per AC 20-191 and operated and maintained in accordance with the provisions of this AC for CAT II may be authorized. The approved automatic FGS may not be used below 100 feet HAT for this operation, unless otherwise authorized by the Flight Technologies and Procedures Division. This type of authorization requires coordination with the Flight Technologies and Procedures Division and may require further evaluation via an approved NTD.

f. SA CAT II.

(1) SA CAT II differs from standard CAT II primarily by decreased runway and approach lighting requirements (i.e., TDZ lighting and runway centerline lights not required). A MALSR or a SSALR can be substituted for (normally required) ALS with Sequenced Flashing Lights (ALSF-1/2). HIRLs are still required for SA CAT II operations. Refer to Order 8400.13 for additional information on airfield infrastructure requirements (e.g., lighting, power, air traffic, etc.) if required. Operators must be authorized for SA CAT II operations via OpSpec/MSpec/LOA paragraph C060 and must use aircraft currently operationally approved for autoland or HUD with guidance to touchdown capability. Operators who are authorized to conduct SA CAT II ILS approaches may also continue CAT II operations at runways with standard CAT II/III lighting and a CAT II minimum when TDZ and/or runway centerline lights fail as long as the authorized operator uses autoland or HUD to touchdown. Instrument approach operations may be authorized CAT II minima not less than 100 feet DA/DH. See Table 3-2 for associated approach RVR minima.

(2) The future use of navigation signals other than ILS or vision guidance equipage for SA CAT II operations (e.g., GLS) may require further evaluation of signal suitability and independent airborne system position validation via approved NTD.

(3) SA CAT II operations require the use of an automatic flight control system or a manual FGS designed to meet CAT III criteria of AC 20-191.

(4) An aircraft type and/or system previously approved for CAT III using AC 120-28 or equivalent criteria is considered to meet the requirements of this AC for SA CAT II approval.

g. CAT II Using RVR 1000 Minima. CAT II using RVR 1000 minima may be authorized when meeting provisions of standard OpSpec, MSpec, or LOA paragraph C060 (see Appendix 3). Only those operators with an authorized OpSpec, MSpec, or LOA for CAT II operations using aircraft that are currently certified and maintained for CAT III operations (i.e., autoland or HUD certified to touchdown capability) may be considered eligible for these operations. The OpSpec, MSpec, or LOA must include the limitation requiring the use of autoland or HUD to touchdown as a condition of the minimum. See Table 3-2 for associated approach RVR minima.

i. Visual Reference Requirements. › (4) The reference to Visual Glide Slope Indicator (VGSI) in § 91.175…

TABLE 3-2. SPECIAL AUTHORIZATION CATEGORY II AND CATEGORY II

MINIMA MATRIX

CAT II Authorization DH

Approach/Landing System TDZ RVR

Autopilot HUD FP HUD Autoland

OUSD 100’ 1600

Standard

100’ 1200

100’ N/A 1000

SA CAT II 100’ N/A 1200

N/A = Operation not authorized FP HUD = Fail Passive Cat III certified Head-Up Display

h. Application of a DA/DH or Equivalent (e.g., IM), for CAT II. Procedures using CAT II minima typically use a radio altimeter and the associated DH (of the specified DA/DH) for minima determination.

(1) For CAT II, a DH of a published DA/DH, or an equivalent IM, is used as the applicable descent minima. Any “altitude” value specified is considered to be advisory. The altitude value is available for cross reference and backup. Use of the barometrically referenced DA element of a published DA/DH is not currently authorized for part 121, 129, or 135 operations at U.S. facilities.

(2) Procedures that have “Radio Altitude Not Authorized (RA NA)” (e.g., due to irregular underlying terrain) typically use the first indication of arrival at the IM as a means to establish DA/DH. In this instance, both radio altitude and barometric altitude are advisory. However, an operator may elect to use first indication of arrival at either the IM or the barometric altitude DA, whichever comes first, as the means for minima determination. In this case, barometric altitude may be an acceptable means to establish DA/DH, but only if it occurs before arriving at the IM.

i. Visual Reference Requirements.

(1) For SA CAT I operations, the required visual references are those provisions listed in § 91.175(c) and (d).

(2) For all other instrument approach operations below RVR 1800, § 91.189 and Standard OpSpecs or MSpecs specify the required visual references to continue the approach.

(3) For SA CAT II operations, note that the ground lighting system configuration may be non-standard. Refer to subparagraph 3-7f for further detail.

(4) The reference to Visual Glide Slope Indicator (VGSI) in § 91.175 includes the use of Visual Approach Slope Indicators (VASI), precision approach path indicators (PAPI), Pulsating Visual Approach Slope Indicators (PVASI), or tri-color VASIs.

(5) Section 91.176 contains the requirements pertaining to visibility and visual reference when operations are based on using EFVS.

b. Concepts and Objectives. CAT III minima were formerly classified as… › (2) CAT III operations may be conducted manually using approved FGSs,…

j. Precision Approach Radar (PAR). PAR minima may be authorized via OpSpec to minima of not less than 100 feet HAT, or the published minima, whichever is higher. PAR authorizations are limited to those operators and crews specifically qualified to use PAR.

3-8. REQUIREMENTS FOR OPERATIONS BELOW RVR 1000.

a. General CAT III Requirements. The following requirements apply to the operational authorization of CAT III IAPs:

(1) The airborne system should meet the applicable requirements of Chapter 3 and AC 20-191,

(2) Flightcrew qualification consistent with provisions of Chapter 5 for CAT III has been completed,

(3) Appropriate NAVAIDs and airport/lighting facilities for the procedures to be flown, consistent with Chapter 6, should be available,

(4) An acceptable continuing airworthiness/maintenance program for the airborne system provided in accordance with Chapter 7, and

(5) An operational authorization has been completed per Chapter 8 for a U.S. operator or Chapter 9 for a non-U.S. operator.

b. Concepts and Objectives. CAT III minima were formerly classified as CAT IIIa, CAT IIIb, and CAT IIIc. Title 14 CFR part 1 no longer contains definitions of these classifications. CAT III landing minima are now based on and often described in terms of a three-legged stool (i.e., aircraft approach and landing system capabilities, crew qualification, and approach system classification). For example, for a crew authorized for minima as low as RVR 300, if either the aircraft or approach is limited to RVR 600, then the lowest actual minima is limited to RVR 600, which is the highest value of the three legs. Visual conditions encountered in CAT III operations range from visual references being adequate for manual control during rollout to visual references being inadequate even for taxi operations without special visual reference enhancements or suitable synthetic references. Failure effects and system capabilities after failure are associated with different levels of visual conditions (ceiling and visibility) to derive landing minima (AH, DH, and RVR).

(1) Aircraft having statements in the FAA-approved AFM indicating approval for certain CAT III operations (e.g., formerly CAT IIIa operations) are considered to continue to meet the requirements of this AC. Determination of equivalence between previous CAT IIIa, IIIb, and IIIc classifications and CAT III description in terms of failure effects and system capabilities are described below.

(2) CAT III operations may be conducted manually using approved FGSs, automatically using approved autoland systems, or with hybrid systems that employ both

c. Fail Operational (FO) CAT III Systems. An FO system is a system… › (1) As of the publication of this AC, the lowest authorized minima for…

automatic and flight guidance elements. If the particular FGS depicts F/D or other command guidance, it may be approved in accordance with AC 20-191 or equivalent. Additionally, other FGSs may be used if the NTD is satisfactorily demonstrated. When an automatic system is to be the primary means of control, the use of that system should not require pilot intervention. A means for crew intervention must be provided in the event the pilot detects inadequate system performance (e.g., the pilot determines that an automatic landing cannot be accomplished within the TDZ). If a hybrid system is employed, then the primary mode of operation must be automatic to touchdown, with manual control used as an alternate means to complete the operation.

(3) To be approved for CAT III operations, the airplane and its associated systems should be shown to be capable of safely completing an approach, touchdown, and rollout and permitting a safe go-around from any altitude to touchdown following any failure condition not shown to be extremely improbable. A single system failure should not cause total loss of CAT III capability. A combination of failures may cause a loss of CAT III but must not prevent a safe go-around.

(4) Flight deck design, instrumentation, annunciations, and warning systems should be adequate in combination to ensure the pilot(s) can verify the aircraft should touch down within the TDZ and safely rollout when the controlling visibility is reported at or above applicable minima. Concepts other than those currently authorized may be acceptable if NTD testing can demonstrate an equivalent or greater level of safety as presently specified for approval of automatic systems (e.g., hybrid systems or vision enhancement systems).

(5) To be approved for CAT III operations, the airplane and its associated systems should be shown to be able to perform to the necessary level of accuracy, integrity, and availability. This is typically shown initially by the manufacturer during airworthiness demonstration, confirmed during the operational authorization process, and is monitored by the operator on a continuing basis.

(6) CAT III operations are predicated on meeting requirements for CAT II, or equivalent, for that portion of the approach to 100 feet HAT.

(7) The provisions of this AC, or any version of the former AC 120-28 for aircraft previously certified, are considered to be the applicable criteria to assure the necessary performance from flare to landing and rollout.

c. Fail Operational (FO) CAT III Systems. An FO system is a system that, after failure of any single component, is capable of completing an approach, flare, and touchdown, or approach, flare, touchdown, and rollout by using the remaining operating elements of the FO system. The failure effects of single components of the system, airplane, or equipment external to the airplane that could have an effect on touchdown or rollout performance must be considered when evaluating FO systems. FO systems may be used to touchdown with or without a rollout system. Use of an FO system to touchdown in conjunction with a rollout system that is not FO is acceptable as long as suitable minimum RVR values are specified in the OpSpecs.

(1) As of the publication of this AC, the lowest authorized minima for U.S. operators are touchdown, mid, and rollout RVR 300.

(5) The following are typical arrangements that may be acceptable for… › (d) Two independent and adequately monitored manual FGSs with…

NOTE: A landing system is considered to include each of the elements in the aircraft that are necessary to perform the landing and rollout function (e.g., flight control, hydraulic system(s), electrical system(s), and sensors).

(2) The reliability and performance of the required operational systems should be such that continued safe operation to landing, or landing and rollout, can be achieved following any failure condition occurring below the AH that is not shown to be extremely improbable. Systems identified below and in AC 20-191 or equivalent are considered to meet the intent of this provision.

(3) The redundancy required for approval of an FO CAT III aircraft may be provided by multiple automatic landing systems, multiple automatic landing and rollout systems, redundant manual FGSs, or suitably redundant approved hybrid systems (NTD).

(4) Failure conditions that result in the loss or disconnect of all the redundant landing or landing and rollout systems, occurring below the AH, are permissible if the occurrence of these failure conditions is extremely remote and the loss or disconnect is accompanied by acceptable warning indications for the pilots. Airplanes that are demonstrated to meet the airworthiness assessments of AC 20-191 for FO systems are considered to meet these reliability and performance criteria.

(5) The following are typical arrangements that may be acceptable for FO systems:

(a) Two or more monitored fail passive (FP) autopilots or integrated autopilot F/D systems, each with dual channels making up an automatic FO system designed so that at least one autoflight system remains operative after the failure of one system, and the failed system is not used or cannot cause unacceptable autoflight system performance.

NOTE: Following a failure with this configuration, it is not intended that a landing be continued with F/D alone, unless a successful NTD has been completed.

(b) Three autopilots or integrated autopilot F/D systems designed so that at least two remain operative after failure to permit comparison and provide necessary monitoring and protection while continuing to a landing.

(c) A monitored FP automatic flight control system with automatic landing capability to touchdown and rollout, if applicable, plus an independent and adequately failure-protected manual FGS, suitable for landing and rollout with guidance provided for the PF and monitoring displays for the pilot monitoring (PM). An NTD may be necessary for this arrangement.

(d) Two independent and adequately monitored manual FGSs with independent displays for the PF and the PM, each capable of supporting a landing and rollout. An NTD would be necessary for this arrangement.

d. Alert Height. › (3) Airworthiness demonstration of an AH is specified in AC 20-191.

(6) Aircraft meeting FO requirements of AC 20-191, or equivalent, for landing and rollout may be authorized for FO CAT III to the lowest currently applicable minima specified in OpSpecs for this type of system.

(7) Aircraft previously demonstrated to meet acceptable FO criteria may receive additional credit beyond those already authorized, as specified in provisions of this AC, through proof of compliance with applicable operational provisions of this AC and any subsequent amendment of applicable OpSpecs.

(8) Aircraft with an FO landing system, but without a rollout system, that were originally approved in accordance with previous versions of AC 120-28 may typically be approved for minima not less than TDZ and mid RVR 600. Eligibility for RVR 600 requires compliance with appropriate current Service Bulletins (SB) in accordance with the manufacturer’s recommendations, and a determination by FAA that “in-service” operational performance of the system is acceptable.

(9) Aircraft originally approved in accordance with FAA “Special Conditions” for a rollout system, or criteria of versions of AC 120-28, are considered to have rollout capability equivalent to FO for minima not less than TDZ, mid, and rollout RVR 300. For these aircraft, appropriate current SB compliance should be reviewed and completed, and line operational performance of the system must be shown to be acceptable. However, it is important to note that, as with other aircraft types, CAT III authorization for some of these aircraft may be restricted to certain runway facilities since landing or rollout performance may not necessarily be acceptable due to site-specific irregular underlying approach terrain, TDZ slope, or ILS beam characteristics.

d. Alert Height.

(1) FO CAT III is based on use of an AH. The AH is the height above a runway based on characteristics of the airplane and its FO system, above which a CAT III approach must be discontinued and a missed approach initiated if a failure occurs in one of the redundant parts of the flight control or related aircraft systems, or if a failure occurs in any one of the relevant ground systems. The AH design philosophy requires an aircraft be capable of safely completing a touchdown and rollout (if applicable) following a single failure occurring in the systems noted above, below the specified AH.

(2) Operational AHs must always be equal to or lower than that specified in the airworthiness demonstration, and may be specified at or below 200 feet HAT. The AH is specified by an operator of an aircraft and approved by the FAA. The operational AH used must be consistent with the aircraft design, training, ground facilities, and other factors pertinent to the air carrier’s operation. Typically, a minimum usable operational AH is 50 feet HAT. Lower AHs may be approved if there is an appropriate reason to do so (e.g., for certain types of hybrid systems).

(3) Airworthiness demonstration of an AH is specified in AC 20-191. To ensure the necessary reliability of aircraft systems, airworthiness demonstrations of AH should be from an altitude of at least 200 feet above the TDZ elevation.

(6) Typical arrangements that may be used to meet the requirements for… › (c) An FGS designed for manual control by the PF (e.g., FP HUD), and…

e. Fail Passive CAT III Systems.

(1) A fail passive system is a system that, in the event of a failure, causes no significant deviation of aircraft flightpath or attitude. The capability to continue the operation may be lost and an alternate course of action (e.g., a missed approach) may be required. An FP system is the minimum acceptable system for CAT III operation with a DH.

(2) FP approach operations meeting provisions of AC 120-28, AC 20-191, or equivalent, are typically conducted with a DH not lower than 50 feet, and are limited to RVR values that provide suitable visual reference to address normal operations as well as failure contingencies. Authorization of DH less than 50 feet HAT may require NTD.

(3) An FP CAT III system does not provide sufficient redundancy to successfully continue the approach and landing to touchdown following any failure in the flight control system not shown to be extremely remote. Therefore, a DH is specified in this instance. In the event of a failure of the airborne system at any point in the approach to touchdown, a missed approach is required. However, this provision does not preclude a pilot’s authority to continue an approach if continuation of an approach is considered by the pilot to be a safer course of action.

(4) Such a failure, however, does not preclude continuation to CAT I or CAT II minima if the necessary remaining elements of the aircraft system are operational and if the flightcrew qualification addresses necessary action to continue such an approach is met. Any adjustments to approach minima or procedures made on final approach should be completed at a safe altitude.

(5) An aircraft using an FP system for CAT III should be shown to provide the capability to touchdown in the TDZ or to complete a safe manual or automatic go-around. This capability should be demonstrated from any altitude to touchdown following any failure condition not shown to be extremely improbable.

(6) Typical arrangements that may be used to meet the requirements for CAT III FP operations using a 50 feet DH include the following:

(a) A single monitored automatic flight control system with automatic landing capability.

(b) An FO automatic flight control system with automatic landing that has reverted to an FP configuration or has been dispatched in an FP configuration. This provision is in place for dispatch and prior to initiating the approach. It is not intended to allow switching to an FP configuration if a FO system degrades during the approach. In that event, a missed approach should be initiated.

(c) An FGS designed for manual control by the PF (e.g., FP HUD), and for monitoring by the PM. Aircraft intended for FP CAT III operations should have aircraft systems that meet the criteria specified in AC 20-191. Aircraft previously demonstrated to meet earlier FP criteria may continue to operate using CAT III minima in accordance with approved OpSpecs.

g. CAT III Operations with Not Lower than RVR 700 Landing Minima. › (4) Aircraft demonstrated to meet the airworthiness provisions of AC…

f. Decision Height.

(1) For CAT II and certain CAT III procedures (e.g., when using an FP landing system), a DH (or an approved equivalent) is used as the controlling minima. The “Altitude” value specified is considered as advisory and is available for cross reference. Use of a barometrically referenced DA for CAT III is not currently authorized.

(2) A DH is applied to all FP operations and is specified at certain international locations where FO minima are authorized. For CAT III, a DH is a specified radio altitude above terrain on the final approach or TDZ. The DH is established to ensure that prior to passing that point the pilot is able to determine that adequate visual reference exists to allow verification that the aircraft should touch down in the TDZ.

g. CAT III Operations with Not Lower than RVR 700 Landing Minima.

(1) Operations with landing minima of not lower than RVR 700 may be conducted with a FO or FP landing system, with or without a rollout control system (See Table 3-3, Lowest Minima Currently Authorized for Fail Operational or Fail Passive Landing Systems, or Landing and Rollout Systems, for specific minima). Previous testing and harmonization efforts led to lowering CAT IIIa minima to RVR 600; however, CAT III operations with RVR 700 minima are the lowest suitable for use on navigation facilities that support guidance for positioning through touchdown but do not support unmonitored rollout guidance. Some facilities and/or legacy aircraft are limited to RVR 700 based upon approach classification or aircraft certification. See subparagraph 3-8i, CAT III Operations RVR Minima Rationale, below for further discussion. These operations were formerly defined as CAT IIIa in the CFR and FAA documents. They may still be defined as CAT IIIa in ICAO annexes and foreign documents.

NOTE: Some FAA instrument procedures may still retain CAT IIIa nomenclature until these procedures are updated or amended.

NOTE: Reported TDZ and mid RVR must meet the approach chart minima to conduct any CAT III operation. The reported rollout RVR, while still controlling, may be lower than charted minima, if authorized via OpSpec.

(2) Operations using an FO system without an operational rollout control system require the use of a DH to ensure suitable visual reference of the TDZ.

(3) For FO systems, there should be a sufficient combination of information from flight instruments, annunciations, and alerting systems to ensure the pilot can verify that the aircraft should touch down within the TDZ, and safely initiate rollout.

(4) Aircraft demonstrated to meet the airworthiness provisions of AC 120-28 for FP systems remain eligible for any previously approved operational authorization under provisions of this AC and do not require additional airworthiness demonstration. Aircraft previously having completed an airworthiness demonstration in accordance with AC 120-28 remain eligible for any operational authorization that was permitted by AC 120-28.

h. CAT III Operations with Landing Minima RVR 600 or Less. › (3) Operations based on FO systems with an approved rollout system are…

(5) Aircraft demonstrated to meet airworthiness criteria prior to AC 120-28B, and not currently authorized in OpSpecs for CAT III, may be approved for new FP CAT III operations on a case-by-case basis depending on facilities to be used, SB compliance status, and other relevant safety factors.

(6) Aircraft that were authorized for FO CAT III, but have not been demonstrated to meet the provisions for FP systems shown in previous versions of AC 120-28 or AC 20-191, may be approved for FP operations with landing minima limited to RVR 1000 provided the following criteria are met:

(a) The aircraft must be shown to be in compliance with relevant SBs for the applicable flight control system and displays.

(b) An auto throttle system must be installed and operational.

(c) The system must be shown to provide reliable autoland performance in line operations.

(d) A demonstration using an appropriately approved full flight simulator (FFS) or aircraft must be completed for that operator and aircraft type, showing that the system and procedures applicable to FP operations can be practically applied for that air carrier’s operation.

(7) Aircraft not previously authorized or not currently authorized by the FAA to use minima less than RVR 1000 based on a FP system must meet the airworthiness requirements of AC 20-191 or equivalent for any new authorization of minima less than RVR 1000.

(8) New aircraft types or derivative aircraft with new flight control system designs should be demonstrated in accordance with AC 20-191 for FP systems, or equivalent requirements, if FP authorization is sought.

h. CAT III Operations with Landing Minima RVR 600 or Less.

(1) CAT III operations with landing minima of RVR 600 or less are usually conducted with FO systems. These operations were formerly defined as CAT IIIb in the CFR and FAA documents, and may still be defined as CAT IIIb in some ICAO annexes and foreign documents.

(2) Airborne systems authorized for landing at or below mid RVR 600 must include a rollout system. Either a manual FGS or an automatic rollout or control system for lateral steering may be acceptable. Either system must provide the means to control the aircraft until the aircraft slows to a safe taxi speed. Operations based on FO systems require the use of systems that, after passing AH, are capable of the safe completion of the approach, touchdown, and rollout, following any failure conditions not shown to be extremely remote. When FO systems are used, they do not require operating procedures which specify that the approach must be continued after a failure.

(3) Operations based on FO systems with an approved rollout system are generally conducted to an AH. The availability of visual reference is not a specific requirement for continuation of an approach to touchdown. The design of flight instrument systems,

i. CAT III Operations RVR Minima Rationale. › (4) RVR 600 is the lowest RVR that provides visual cues necessary in…

annunciations, and alerting systems should be adequate to ensure the pilot can verify the aircraft should touch down within the TDZ and rollout.

(4) Operations may be conducted to a TDZ RVR of not less than 600 and a mid RVR not less than 400 with an FO or FP landing system and with any FAA-approved rollout control system.

(5) Operations may be conducted to a TDZ and mid RVR not less than 400 when using an FO landing system and a rollout control system shown to meet FP criteria of AC 20-191 (or earlier FAA criteria applicable to a rollout system).

(6) In all cases above, operations may be conducted with a rollout RVR as low as 300.

(7) Irrespective of CAT III definitions and certification standards which may reference lower RVR minima, as of the publication of this AC, the lowest authorized minima for U.S. operators are touchdown, mid, and rollout RVR 300. A summary of the minima that may now be authorized based on the above criteria are shown below in Table 3-3.

(8) See note below for criteria, and subparagraph 3-8c above for examples of various aircraft types, systems, and minima that may be authorized.

NOTE: AC 120-28D Appendix 3 amended criteria for FO rollout control systems. As a result, certain systems previously certificated using the criteria of AC 120-28B or 120-28C, which were not considered FO due to conditions noted in the AFM as exceptions, were considered under AC 120-28D to meet FO criteria.

i. CAT III Operations RVR Minima Rationale.

(1) The concept of CAT III approach requires no visual segment. However, TDZ RVR values must be sufficient such that adequate visual reference exists to allow verification that the aircraft should touch down in the TDZ when using FP landing systems. The TDZ RVR values shown in Table 3-3 for FP systems are not sufficient for an unguided, visual landing, but are only sufficient for the pilot to verify aircraft position to land when arriving at DH. TDZ RVR values must also be adequate for initial pilot control of rollout after touchdown either without a rollout system or in case of FP rollout system failure.

(2) Mid RVR reports must be sufficient to allow pilot visual confirmation of rollout guidance system performance and also be sufficient to support safe, unguided, manual control during the high speed rollout segment in case of FP system failure.

(3) Minimum rollout RVR in all cases must support low speed (40 knots or less) rollout and taxi operations. For aircraft or operator procedures known to require the maximum allowable rollout distance and commensurate higher speed in the rollout RVR area, a higher required RVR report may be necessary.

(4) RVR 600 is the lowest RVR that provides visual cues necessary in verifying that the aircraft should touchdown in the TDZ using a 50 foot DH or during unguided rollout. RVR 600

j. Previously Approved CAT I/II/III Operations or Use of Previous or… › (1) Approval criteria used for a particular aircraft are typically…

is therefore the minimum required for landing operations using a 50 foot DH (i.e., with FP landing systems) and high speed rollout in the mid RVR area without a rollout system. Lower RVR values and associated DH using hybrid systems may be acceptable upon completion of NTD testing. RVR 400 is the minimum visibility necessary to confirm proper rollout system operation or for control in case of rollout system failure. Therefore, RVR 400 is the lowest visibility assigned for FP system controlled rollout in the mid RVR area. RVR 400 is also necessary for an FO landing system if the rollout system is FP. RVR 300 is the lowest visibility used for operations with FO landing and rollout systems. While visual references for touchdown or rollout are not required for FO systems, RVR 300 is used for all FO CAT III operations as a practicable minimum value for final, low speed rollout to runway turnoff. RVR 300 is also accepted as the lowest generally useable minimum for safe ground operations using natural vision. Lower RVR values for FO systems may be achievable through the use of advanced vision or sensor systems upon successful completion of an NTD.

(5) A summary of the minima that may now be authorized based on the above criteria are shown below in Table 3-3.

TABLE 3-3. LOWEST MINIMA CURRENTLY AUTHORIZED FOR FAIL OPERATIONAL OR FAIL PASSIVE LANDING SYSTEMS, OR LANDING AND

ROLLOUT SYSTEMS

Landing System

Type

Rollout System

Type

TDZ RVR Mid RVR Rollout RVR

FP or FO None 600 (175m) 600 (175m) 300 (75m)

FP FP or FO 600 (175m) 400 (125m) 300 (75m)

FO FP 400 (125m) 400 (125m) 300 (75m)

FO FO 300 (75m) 300 (75m) 300 (75m) NOTE: “Relevant” or “applicable” mid or rollout RVR is considered to be any RVR sensor report (or equivalent instrumentally derived RVR measurement) considered to be covering a portion of the runway where the aircraft is operating at a speed above a safe taxi speed (See subparagraph 6-4b).

j. Previously Approved CAT I/II/III Operations or Use of Previous or New CAT I/II/III Criteria. Operators approved in accordance with AC 120-29 or AC 120-28 may continue to operate in accordance with their previously approved program, consistent with current standard OpSpecs or any special provisions approved for that operator in that operator’s approved OpSpecs.

(1) Approval criteria used for a particular aircraft are typically listed in an AFM. If not shown in an AFM, the applicable FAA Aircraft Evaluation Division may be consulted through the POI or certificate management office (CMO) to determine eligibility.

3-10. RUNWAY VISUAL RANGE. › a. Controlling RVR. The controlling RVR(s) are those reported values of…

(2) Aircraft qualified using other than FAA criteria will be as designated in approved OpSpecs or as designated by the applicable Aircraft Evaluation Division (e.g., through the FAA Flight Standardization Board (FSB) Report for the aircraft type) or the Flight Technologies and Procedures Division.

(3) Aircraft demonstrated to meet airworthiness provisions of versions of AC 120-29 or AC 120-28 may remain eligible for previously approved operational authorizations. Additional airworthiness demonstrations are not necessary for these aircraft unless the operator specifically seeks additional credit based on the provisions of this AC.

(4) Operators seeking credit provided for only by this AC which was not available in previous versions of AC 120-29 or AC 120-28 must meet operational criteria as described in the main body of this AC.

3-9. VISIBILITY AND RVR. Visibility minima are as specified in standard or special IAPs approved for use by the operator, or as otherwise listed in standard OpSpecs applicable to that operator. CAT I operating minima may be expressed as meteorological visibility or RVR while SA CAT I/II, CAT II, and CAT III minima are expressed solely in RVR. Takeoff minima below ¼ statute mile/RVR 1600 are expressed solely in RVR.

a. Meteorological Visibility. Meteorological visibility may be used as reported by the National Weather Service (NWS), a source approved by the NWS to include U.S. Military weather reporting facilities, by FAA, or a source approved by the Administrator.

b. Overseas Visibility Reporting. Outside of the United States, the FAA may accept meteorological reporting sources for use by a particular operator. Outside of the United States, meteorological visibility determination may vary. An operator should ensure that the meaning, definition and significance of any meteorological visibility reported for use in determining minima is understood by that operator’s pilots.

c. Non-NWS Sources. For approval of use of aviation weather sources not already addressed by current directives, operators should consult their responsible Flight Standards office. Air carriers should refer to § 121.101 for pertinent information on non-NWS weather reporting facilities. A Flight Standards office requiring assistance in responding to operator inquiries regarding approval of weather sources should consult the Flight Technologies and Procedures Division.

3-10. RUNWAY VISUAL RANGE. RVR is an instrumentally derived value measured by transmissometers or forward-scatter meters. RVR is calibrated by reference to runway lights and/or the contrast of objects.

a. Controlling RVR. The controlling RVR(s) are those reported values of one or more RVR reporting locations used to determine if operating minima are met for the purpose of takeoff initiation, approach initiation, or in some cases, approach continuation. For instrument approaches described in this AC, the controlling RVR(s) are as specified by the operator’s authorization.

3-11. RUNWAY FIELD LENGTH REQUIREMENTS AND RUNWAY CONTAMINATION. › d. Emergency Return After Takeoff. When an operator needs to provide…

b. Operating Minima. U.S. operating minima below ½ statute miles (RVR 2400) for landing and ¼ statute miles (RVR 1600) for takeoff are generally based on RVR as reported by the controlling agency. For EFVS operations, refer to § 91.176 and AC 90-106.

c. Instrumentally Derived RVR Limitations. The use of RVR has practical limitations that should be familiar to both the operator and pilot. For example, RVR is a value that typically only has meaning for the portions of the runway associated with the RVR report. RVR is a value that may vary with runway light step settings (1 through 5). Operators should ensure that pilots are familiar with runway light setting effects on reported RVR. RVR may not be representative of actual visibility along portions of the runway due to the location of the sensor baseline and limited length of the baseline, or due to variable conditions of fog, blowing snow, or other obscurations along the runway, obscurations varying rapidly in time (e.g., patchy fog), or due to lighting source (e.g., LED or incandescent). Thus, pilots and operators should note that RVR is an instrumentally derived value that has operationally significant limitations and can be greater than or less than the actual visibility available to a pilot at typical flight deck eye height. This is particularly true at night, if runway lights are not at settings standard for the prevailing conditions, or if unusual daylight conditions are experienced (e.g., a runway aligned with a sunrise or sunset condition, in shallow or patchy fog).

d. Non-Instrumentally Derived RVR Reports. Outside of the United States, some RVR reports may not necessarily be instrumentally derived, and may alternately be made by pilots or other weather observers. Accordingly, operators should ensure that the meaning, definition, significance, and variability of any non-instrumentally derived value of RVR reported to the pilot for use in determining minima is understood by that operator, and that operator’s pilots.

3-11. RUNWAY FIELD LENGTH REQUIREMENTS AND RUNWAY CONTAMINATION. Landing distance requirements are specified by operating rule and are further expanded upon below.

a. AFM Landing Distance Data. All operators should understand the basis by which their landing distance charts are constructed, to include which factors were used to ensure compliance with any applicable portions of their operating rules.

b. Wet Runway Considerations. If it is determined during dispatch that the landing runway may be wet, the effective runway length must meet the requirements of the applicable operating rules. Operators should consider the possible need for an adequate buffer beyond that required by these operating rules if braking action is reported or expected to be less than “good.” Further details may be found in AC 91-79 and AC 121.195-1.

c. Use of Autobrakes. Prior to dispatch or release, the pilot should possess and consider any necessary information regarding AFM stopping distance data upon which dispatch was determined (e.g., autobrake setting). If FAA-approved AFM autobrake data conforming to AC 121.195-1 is to be used, then the operator should provide the applicable stopping distance information/autobrake setting and stopping procedures to the flightcrew.

d. Emergency Return After Takeoff. When an operator needs to provide for an instrument approach and low-visibility landing following an emergency return after takeoff, or

(4) Runway Field Length Airborne Considerations. › (b) Information on autobrake distance provided by the manufacturer may…

when using a takeoff alternate, the operator should consider the expected landing configuration, braking method, and initial braking speeds in assessing landing field length requirements (e.g., consider landing weight, engine out flap settings, engine inoperative speeds as applicable, potential for partial brakes, or partial antiskid, or inoperative reverse thrust).

e. Alternate Airport Field Length. When determining alternate airport field length provisions in accordance with the applicable operating rule, it is recommended that the operator consider the engine inoperative weights, flap settings, and approach speeds that may be applicable for that alternate airport. The operator must consider engine inoperative speeds and configurations in the assessment of the required landing distance in order to receive credit for the use of a CAT II alternate airport based on “Engine Inoperative CAT II” capability.

f. Acceptable Field Length Factors and Considerations. The following field length factors and elements should be considered:

(1) The Runway Field-Length Requirement for operations when conditions are expected to be below RVR 4000 is as specified by the applicable operating rule for a wet runway.

(2) The use of declared distances for runways should follow guidance provided in AC 150/5300-13, Airport Design. Declared distances are listed in the FAA Chart Supplement for all runways at certificated airports. NOTAMs may have an effect on the declared distances of runways due to airport construction, Runway Safety Area (RSA) construction and/or special events. Operators are responsible for the proper application of NOTAMs with respect to runway declared distances.

(3) Braking Action Considerations. CAT II and/or III operations should not normally be conducted with braking action less than “fair.” Operators should ensure that timely updates of field conditions are provided to the flightcrew, and dispatcher, if applicable. The flightcrew and/or dispatcher should be able to assess from the updates whether sufficient runway length is available for the landing in the conditions reported.

(4) Runway Field Length Airborne Considerations.

(a) In the event of unforecast adverse weather en route to the destination, or if braking system or other failures affecting stopping performance occur while en route, the crew should consider any adverse landing distance consequences that may result from a decision to make a landing on a particular runway (e.g., braking action reports, runway surface composition and length, reported runway and weather conditions, AFM limitations, operational procedures, and aircraft equipment status).

(b) Information on autobrake distance provided by the manufacturer may be used as the basis for field length determinations prior to execution of the approach. When autobrake systems are used, information must be available to the flightcrew to assist in making the proper selection of a suitable autobrake setting consistent with the field length available for landing and the runway condition, including braking action. If FAA-approved AFM certificated autobrake data conforming to AC 121.195-1 is used as the basis for determining acceptable landing distance, the operator should ensure that appropriate factors for use of autobrakes are considered,

(2) The authorization for aircraft to operate using CAT III minima… › (b) The braking system characteristics of the aircraft regarding…

and if appropriate, accounted for (e.g., brake configuration, autobrake setting(s), runway surface friction, and runway slope).

3-12. ROLLOUT DECELERATION SYSTEMS OR PROCEDURES FOR CAT II AND/OR III.

a. Stopping Means. A means to determine that an aircraft can be reliably stopped within the available length of the runway is necessary to conduct CAT II/III operations. At least one of the following means to assess stopping performance should be used:

(1) An automatic braking system that includes information for the flightcrew about appropriate autobrake settings to be used for landing or that provides landing distance information suitable for use by the flightcrew to determine which autobrake setting may or may not be appropriate.

(2) A ground-speed indicating system based on inertial information or other equivalent source such as Global Navigation Satellite System (GNSS), together with acceptable procedures for its use.

(3) A deceleration display or other indication that can advise the pilot of the adequacy of aircraft deceleration to stop within the available runway length.

(4) A runway remaining indicator display reliably showing the length of remaining runway after touchdown.

(5) A procedural means to assure a safe stop acceptable to the FAA for minima at or above RVR 300. An automated system is required for minima less than RVR 300.

b. Antiskid Systems. Unless otherwise specified by the FAA, aircraft authorized for CAT I and II do not have specific antiskid system installation or use requirements beyond those specified in the applicable AFM, applicable FAA-approved Master Minimum Equipment List (MMEL) and MEL, and applicable field length operating rules.

(1) Unless otherwise determined to be acceptable to the FAA, aircraft authorized for CAT III should have an operable antiskid system installed and operative per the applicable FAA-approved MMEL and MEL.

(2) The authorization for aircraft to operate using CAT III minima without antiskid is determined by the POI for each aircraft type, considering the following factors:

(a) Extra field length margin of runways to be authorized, compared with field lengths necessary for the aircraft type, and

(b) The braking system characteristics of the aircraft regarding susceptibility to tire failure during heavy braking, and susceptibility to tire failure during operations with reduced or patchy runway surface friction.

Par 3-13 Page 33 (and 34)

3-13. VISION SYSTEMS. Certified vision systems may be used in accordance with applicable airworthiness and operational approvals. Use of other vision systems must be demonstrated to be acceptable through NTD testing prior to consideration for operational approval.

CHAPTER 3. OPERATIONAL CONCEPTS › 3-14. HYBRID SYSTEMS.

a. Synthetic Vision Systems (SVS)/Enhanced Vision Systems (EVS) Situation Awareness. SVS and/or EVS may be used to enhance situational awareness during CAT I, II, or III AWO operations.

b. Synthetic Vision Guidance Systems (SVGS). SVGS are typically implemented on a primary display. The display integrates flight guidance information (path deviation indications and command guidance) with a geospatially corrected image of the landing runway, the surrounding environment, and trajectory reference information. The trajectory reference information includes Flight Path Vector (FPV) and flightpath angle reference cue (FPARC). The trajectory reference information will provide the pilot with indications that the trajectory is projected to the runway TDZ (refer to AC 20-185 for information on SVGS airworthiness approval). In a system designed to support operations in which additional credit is sought, the system must meet the integrity, accuracy, and reliability requirements appropriate for the operation.

c. Enhanced Flight Vision Systems. For a description of EFVS, refer to § 91.176 and AC 90-106.

3-14. HYBRID SYSTEMS. Hybrid systems (e.g., an FP autoland system used in combination with a monitored HUD FGS) may be acceptable for CAT III if each element of the system alone is shown to meet its respective suitability for CAT III, and if taken together, the components provide the equivalent performance and safety to a non-hybrid system as specified for the minima sought (e.g., FO CAT III). Hybrid systems should meet the criteria specified in AC 20-191 or may be authorized following a successful NTD. For hybrid systems used for CAT III, an AH or DH will be determined and demonstrated during authorization.

Continue reading ↓ 120 of 362 passages shown