Radar Vectors
FAA Order Cancelled Issued Feb 4, 2015 AIR-100 322 pages Copy saved Nov 18, 2026

Order 8130.2H Airworthiness Certification of Products and Articles

This document is cancelled. Cancelled by 8130.2J. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION ORDER

8130.2H

02/04/2015 National Policy

SUBJ: Airworthiness Certification of Products and Articles

This order establishes procedures for accomplishing original and recurrent airworthiness certification ofaircraft and related products and articles. The procedures contained in this order apply to Federal Aviation Administration (FAA) manufacturing aviation safety inspectors (ASI), to FAA airworthiness AS Is, and to private persons or organizations delegated authority to issue airworthiness certificates and related approvals.

Suggestions for improvement of this order may be submitted using the FAA Office of Aviation Safety (AVS) directive feedback system at http://avsdfs.avs.faa.gov/default.aspx, or FAA Form 1320-19, Directive Feedback Information, found in appendix I to this order.

DC!JDCfi·~

David Hempe Manager, Design, Manufacturing, &

Airworthiness Division Aircraft Certification Service

Distribution: Electronic Initiated By: AIR-100

Section 2. Airworthiness Certificates

100. 101.

Table of Contents

Paragraph Page

Chapter 1. Introduction

Purpose of This Order … 1-1 Audience … 1-1 102. Where Can I Find This Order … 1-1 103. Explanation of Policy Changes … 1-1 104. Cancellation … 1-1 105. Effective Date … 1-1

Chapter 2. General Policies and Procedures

Section 1. General Information

200. Definition of the Term “Airworthy” for U.S. Type-Certificated Aircraft … 2-1 201. Representatives of the FAA Authorized To Issue Airworthiness Certificates and Related Approvals … 2-1 202. Responsibilities of FAA ASIs and Designees … 2-2 203. Possession and Display of Airworthiness Certificates … 2-2 204. Aircraft Registration … 2-3 205. Size of Aircraft Nationality and Registration Marks … 2-3 206. Display of Nationality and Registration Marks on Antique and Antique Replica Aircraft … 2-3 207. Original and Replacement Aircraft Identification Plates … 2-4 208. Public Aircraft Operations … 2-6 209. Aircraft Being Removed From a Continuous Maintenance System … 2-6 210. Operation of Civil Aircraft With a Door Open or Removed for Parachuting, Skydiving, or Other Special Operations … 2-6 211. Banner Towing … 2-7 212 Former Military Aircraft … 2-8 213. Aircraft Equipped With Explosive Devices or Jettisonable Stores … 2-9 214. Reserved … 2-10

Section 2. Airworthiness Certificates

215. General … 2-10 216. Classification and Category of Airworthiness Certificates … 2-10 217. Replacement, Exchange, or Amendment of Airworthiness Certificates … 2-10 218. Surrendered Airworthiness Certificate … 2-12 219. Aircraft Model Change … 2-13

ii

225.

309. 310.

Table of Contents (Continued)

Section 2. New Aircraft

Paragraph Page

220. Recording of Conformity Inspections … 2-13 221. Airworthiness Certification of Manned Free Balloons … 2-13 222.-223. Reserved … 2-14

Section 3. Initial or Subsequent Issuance of Airworthiness Certificates (Original/Recurrent) or Related Approvals

224. General … 2-14 Airworthiness Certification … 2-15 226. Exceptions … 2-15 227. Recording of Conformity Inspections … 2-15 228. Eligibility and Evaluation of U.S. Military Surplus Flight Safety-Critical Aircraft Parts (Articles) (FSCAP), Engines, and Propellers … 2-16 Figure 2-1. Sample Aeronautical Center Form 8050-64,

Figure 2-3. Sample Limitations for the Operation of an Aircraft

Figure 2-4. Sample FAA Form 8100-1, Conformity Inspection

Assignment of Special Registration Numbers … 2-26 Figure 2-2. Sample Response Letter Regarding Identification Plates .. 2-27

With a Door Removed … 2-28

Record (Face Side Only) … 2-30

Chapter 3. Standard Airworthiness Certification

Section 1. General Information

300. General … 3-1 301. Standard Airworthiness Certificate … 3-1 302. Application for Airworthiness Certificate … 3-2 303. Statement of Conformity … 3-2 304. Determining Conformity … 3-2 305. Basic Eligibility Requirements … 3-3 306. Certification Procedures … 3-3 307.-308. Reserved … 3-5

Section 2. New Aircraft

General … 3-6 Certification Procedures … 3-6 311. Aircraft Manufactured Under a TC (Without an FAA Production Approval) … 3-6 312. 313. Aircraft Manufactured Under a PC … 3-6 Airworthiness Certification of Very Light Aircraft (VLA) … 3-7

iii

Section 3. Used Aircraft and Surplus Aircraft of the U.S. Armed Forces

Table of Contents (Continued)

Paragraph Page

314. Aircraft Manufactured in a Bilateral Country … 3-7 315. New Aircraft Manufactured Under the Provisions of § 21.6(b) … 3-7 316.-318. Reserved … 3-12

Section 3. Used Aircraft and Surplus Aircraft of the U.S. Armed Forces

319. 320. General … 3-13 Certification Procedures … 3-13 321. Conformity Determination … 3-13 322. Flight Testing … 3-14 323. Issuance of Standard Airworthiness Certificates Under § 21.183(d)—Used Aircraft and Surplus Aircraft of the U.S. Armed Forces … 3-14 324. Screening of Surplus Military Aircraft … 3-18 325. State of Conformity—Military Aircraft (FAA Form 8130-31) … 3-20 326. Issuance of Standard Airworthiness Certificates, Surplus Military Aircraft … 3-20 327. Certification Requirements (Applicant) … 3-21 328. Certification Procedures … 3-22 329. Examples of Forms … 3-23 Figure 3-1. Sample FAA Form 8100-2, Standard Airworthiness

Figure 3-2. Sample FAA Form 8100-2, Standard Airworthiness Certificate, Aircraft Assembled from Spare and Surplus Products

Figure 3-3. Sample FAA Form 8100-2, Standard Airworthiness

Figure 3-4. Sample FAA Form 8100-2, Standard Airworthiness

Figure 3-5. Sample FAA Form 8130-11, Checklist and

Figure 3-6. Sample FAA Form 8130-9, Statement of Conformity,

Figure 3-7. Sample FAA Form 8130-31, Statement of Conformity—

Figure 3-8. Sample FAA Form 8130-10, Surplus Military Aircraft Inspection Record, No Reasonable Potential for

Figure 3-9. Sample FAA Form 8130-10, Surplus Military Aircraft

Figure 3-10. Sample FAA Form 8100-2, Standard Airworthiness

Certificate, New Aircraft (Face Side) … 3-23

and Articles … 3-23

Certificate, VLA Under § 21.183(a) … 3-24

Certificate, EASA CS/VLA Under § 21.183(c) … 3-24

Inspection Record, Aircraft Built From Spare and Surplus Articles … 3-25

Aircraft Built From Spare and Surplus Articles … 3-33

Military Aircraft … 3-35

Standard Certification … 3-38

Inspection Record, Reasonable Potential for Standard Certification … 3-39

Certificate, Surplus Military Aircraft … 3-40

iv

Section 4. Limited Airworthiness Certification

Table of Contents (Continued)

Paragraph Page

Chapter 4. Special Airworthiness Certification

Section 1. General Information

400. General … 4-1 401. Application for Airworthiness Certificate … 4-1 402. Certification Procedures … 4-1 403. Special Airworthiness Certificates … 4-4 404. Reserved … 4-4

Section 2. Restricted Airworthiness Certification

405. General … 4-4 406. Certification Procedures … 4-5 407. Eligibility … 4-5 408. Special Purpose Operations … 4-6 409. Statement of Conformity … 4-7 410. Operating Limitations … 4-7 411. Airworthiness Certificate … 4-7 412. Display of Marks (Restricted) … 4-7 413.-414. Reserved … 4-7

Section 3. Multiple Airworthiness Certificates

415. General … 4-7 416. Certification Procedures … 4-7 417. Eligibility … 4-7 418. Special Purpose Operations … 4-8 419. Airworthiness Certificates … 4-8 420. Operating Limitations … 4-8 421. Operating With Multiple Airworthiness Certificates, Standard and Restricted or Limited … 4-8 422. Display of Marks (Restricted or Limited) … 4-9 423. Reserved … 4-9

Section 4. Limited Airworthiness Certification

424. General … 4-9 425. Certification Procedures … 4-9 426. Eligibility … 4-9 427. Operating Limitations … 4-10 428. Display of Marks (Limited) … 4-10

v

Table of Contents (Continued)

Paragraph Page

429. Aircraft Issued Limited Category TCs … 4-10 Table 4-1. List of Aircraft Issued Limited Category TCs … 4-11 430. Reserved … 4-12

Section 8. Experimental LSA Airworthiness Certifications

Section 5. Primary Category Aircraft (PCA) Airworthiness Certifications

431. General … 4-13 432. Certification Procedures … 4-14 433. Reserved … 4-14

Section 6. Light-Sport Aircraft (LSA) Category Airworthiness Certifications

434. General … 4-14 435. Certification Procedures … 4-19 436. Prototype and Production Flight Testing … 4-28 437. Flight Test Areas … 4-30 438. Special Flight Permit for Flight Testing LSA Category Operating Limitations … 4-31 439. Issuance of LSA Category Aircraft Operating Limitations … 4-32 440. LSA Statement of Compliance (SOC) … 4-32 441.-442. Reserved … 4-32

Section 7. General Experimental Airworthiness Certifications

443. General … 4-32 444. Eligibility and Program Letters … 4-35 445. Inspection Programs for Experimental Aircraft That Are Turbine-Powered or Weigh Over 12,500 Pounds … 4-36 446. Flight Test Areas … 4-40 447. Operating Outside Flight Test Areas … 4-41 448. Operations in Reduced Vertical Separation Minimum (RVSM) Airspace … 4-42

Section 8. Experimental LSA Airworthiness Certifications

449. General … 4-42 450. Certification Procedures … 4-46 451. Flight Test Areas … 4-53 452. Issuance of Experimental Light-Sport Operating Limitations … 4-55 453. Reserved … 4-55

vi

Table of Contents (Continued)

Paragraph Page

Section 9. Experimental Amateur-Built Airworthiness Certifications

Section 11.

454. General … 4-55 455. Eligibility … 4-55 456. Determination of Major Portion … 4-57 457. Design and Construction … 4-58 458. FAA Evaluation of Amateur-Built Aircraft Kits … 4-61 459. Advising Applicants … 4-62 460. Certification Procedures … 4-64 461. Flight Test Areas … 4-69 462. Issuance of Experimental Amateur-Built Operating Limitations … 4-70 463. Reserved … 4-70

Section 10. Certification and Operation of Aircraft Under the Experimental Purpose of Exhibition or Air Racing

464. General … 4-71 465. Former Military Aircraft … 4-72 466. Brokering … 4-73 467. Ejection Seats … 4-73 468. Special Initial Certification Requirements … 4-73 469. Certification Procedures … 4-76 470. Issuance of Experimental Exhibition or Air Racing Operating Limitations … 4-77 471.-472. Reserved … 4-77

Section 11. Certification and Operation of Aircraft Under the Experimental Purpose(s) of Research and Development, Showing Compliance With Regulations, Crew Training, Market Surveys, and Operating Kit-Built Aircraft

473. General … 4-77 474. Temporarily Suspending an Airworthiness Certificate … 4-78 475. PC Holder and Modifier Experimental Operating Procedure … 4-80 476. Issuance of Experimental Research and Development, Showing Compliance with Regulations, Crew Training, Market Surveys, and Operating Kit-Built Aircraft Operating Limitations … 4-82 477. Reserved … 4-82

vii

Section 13. Special Flight Permits

Table of Contents (Continued)

Paragraph Page

Section 12. Provisional Airworthiness Certification

478. General … 4-82 479. Eligibility … 4-82 480. Special Purpose Operations … 4-82 481. Statement of Conformity … 4-82 482. Certification Procedures … 4-82 483. Special Airworthiness Certificate, FAA Form 8130-7 … 4-83 484. Operating Limitations … 4-83 485.-486. Reserved … 4-83

Section 13. Special Flight Permits

487. General … 4-83 488. Purposes … 4-85 489. Application and Issuance (General) … 4-85 490. Aircraft Inspections … 4-86 491. Special Operating Limitations … 4-87 492. Special Flight Permit for Operation of Overweight Aircraft … 4-88 493. Special Flight Permit for Production Flight Testing for Aircraft Other Than LSA … 4-90 494. Special Flight Permit for Conducting Customer Demonstration Flights … 4-92 495. Special Flight Permit for Certain Large Aircraft for Which Part 125, Certification and Operations: Airplanes Having a Seating Capacity of 20 or More Passengers or a Maximum Payload Capacity of

Figure 4-1. Sample FAA Form 8130-7, Special Airworthiness

Figure 4-2. Sample FAA Form 8130-7, Special Airworthiness Certificate for Restricted Category Aircraft Certificated Under

Figure 4-3. Sample FAA Form 8130-7, Special Airworthiness Certificate for Primary Category Aircraft Certificated Under

Figure 4-4. Sample FAA Form 8130-7, Special Airworthiness Certificate for Primary Category Aircraft Certificated Under

Figure 4-5. Sample FAA Form 8130-7, Special Airworthiness Certificate for Primary Category Aircraft Certificated Under

6,000 Pounds or More, Is Not Applicable … 4-93

Certificate … 4-96

§ 21.25(b)(7) … 4-97

§ 21.184(a) … 4-98

§ 21.184(b) … 4-99

§ 21.184(c) … 4-100

viii

Section 2. Export Approvals

Table of Contents (Continued)

Paragraph Page

Figure 4-6. Sample FAA Form 8130-7, Special Airworthiness Certificate for Experimental to Show Compliance With the CFR … 4-101 Figure 4-7. Sample FAA Form 8130-12, Eligibility Statement,

Figure 4-8. Sample FAA Form 8000-38, Fabrication/Assembly

Figure 4-12. Sample FAA Form 8130-7, Special Flight

Figure 4-13. Sample Special Flight Permit Operating Limitations

Figure 4-14. Sample FAA Form 8130-7, Special Airworthiness

Figure 4-15. Sample FAA Form 8130-7, Special Airworthiness

Figure 4-16. Sample FAA Form 8130-15, Light-Sport Aircraft

Figure 4-17. Sample FAA Form 8130-15, Light-Sport Kit-Built

Amateur-Built Aircraft … 4-102

Operation Checklist … 4-103 Figure 4-9. Sample FAA Form 8130-7, Unlimited … 4-107 Figure 4-10. Sample FAA Form 8130-7, Special Flight Permit … 4-109 Figure 4-11. Sample FAA Form 337, Major Repair and Alteration... 4-110

Permit LSA … 4-111

for LSA Category Production Flight Testing … 4-112

Certificate for LSA Category Aircraft Certificated Under § 21.190 ... 4-113

Certificate for Experimental LSA Certificated Under § 21.191 … 4-114

Statement of Compliance … 4-115

Aircraft Statement of Compliance … 4-116 Figure 4-18. Use of Prior Policy … 4-117

Chapter 5. Export Approval Procedures

Section 1. General Information

500. General … 5-1 501.-504. Reserved … 5-2

Section 2. Export Approvals

505. Eligibility … 5-2 506. Section 21.325, Export Airworthiness Approvals … 5-2 507. Section 21.327, Application … 5-2 508. Issuance of FAA Form 8130-4, Export Certificate of Airworthiness, for Aircraft (§ 21.329) … 5-2 509. Issuance of FAA Form 8130-3, Airworthiness Approval Tag, for Engines, Propellers, and Articles (§ 21.331) … 5-3 510. Responsibilities of Exporters … 5-3 511. Determination for “New” and “Used” Products or Articles … 5-3 512. Preparation of Export C of A … 5-4

ix

Section 3. Aircraft Engines, Propellers, and Articles

Table of Contents (Continued)

Paragraph Page

513. Approval of Modifications … 5-6 514. Export Certificate Number Assignment Card … 5-6 515. Routing and Processing of Export Files … 5-7 516. Issuance of Export C of A for Aircraft Type Certificated in Multiple Categories … 5-7 517. Issuance of Export C of A for Restricted Category Aircraft … 5-7 518. Controversial Information … 5-7 Figure 5-1. Sample FAA Form 8130-4, Export Certificate of

Figure 5-2. Sample FAA Form 8130-1, Application for

Figure 5-3. Aeronautical Center Form 8050-72,

Airworthiness … 5-8

Export Airworthiness Approval … 5-9

Export Certificate Number Assignment Card … 5-11

Chapter 6. Import Procedures

Section 1. General Information

600. General … 6-1 601.-602. Reserved … 6-2

Section 2. Import Aircraft

603. Requirements for U.S. Airworthiness Certification … 6-2 604. Application … 6-3 605. Airworthiness Determination … 6-3 606. Airworthiness Certification of Aircraft With Mandatory Continuing Airworthiness Information (MCAI) … 6-5 607. Certification Procedures … 6-6 608.-609. Reserved … 6-6

Section 3. Aircraft Engines, Propellers, and Articles

610. Airworthiness Determination … 6-6 611. Identification and Marking … 6-8 612. Return to Service … 6-8 613. Special Maintenance Records Consideration … 6-8

x

Table of Contents (Continued)

Paragraph Page

Chapter 7. Special Flight Authorizations (SFA) for Foreign Civil Aircraft

700. General … 7-1 701. Eligibility … 7-1 702. Blanket SFAs … 7-2 703. Application … 7-2 704. Issuance … 7-4 705. Duration … 7-5 706. Operating Limitations … 7-5 Figure 7-1. Sample SFA for the Flight of an Aircraft to a Place

Figure 7-2. Sample SFA for the Flight of an Aircraft to a New State of Registry (This Format Is Generally Applicable to a

Figure 7-6. Sample Blanket SFA for Delivering Aircraft

Where Repairs or Alterations Are To Be Made … 7-8

Single Aircraft Authorization for Ferry Flights) … 7-10 Figure 7-3. Sample SFA for the Purpose of Flight Testing … 7-12 Figure 7-4. Sample Blanket SFA for Customer Crew Training … 7-14 Figure 7-5. Sample SFA for Export Delivery … 7-16

for the Purpose of Export Delivery … 7-18 Figure 7-7. Sample SFA for the Purpose of Demonstration … 7-19 Figure 7-8. Sample SFA for Participating in Aviation Events … 7-21

Chapter 8. Processing Forms, Reports, and Certification Files

800. General … 8-1 801. Review and Completion of FAA Form 8130-6 … 8-1 802. Completion of FAA Form 8100-2 … 8-11 803. Completion of FAA Form 8130-7 … 8-12 804. Instructions for Reviewing a Completed FAA Form 8130-15, Light-Sport Statement of Compliance … 8-13 805. Completion of FAA Form 8130-4 … 8-19 806. Completion of FAA Form 8130-1 … 8-20 807. Examination, Review, and Routing of Certification Files … 8-22 Table 8-1. Documents Required for New and Used Aircraft

Table 8-2. Documents Required for New and Used Aircraft

Figure 8-1. Sample FAA Form 8130-6, Application for

Certification (Standard) … 8-25

Certification (Special) … 8-27

U.S. Airworthiness Certificate … 8-33

xi

Table of Contents (Continued)

Paragraph Page

Appendix A. Acceptance of an Export Certificate of Airworthiness for Used Aircraft Under a Bilateral Agreement

1. Purpose … A-1 2. Responsibilities of Aviation Safety Inspectors (ASI) and Designees … A-1 3. One Hundred-Hour Inspection Requirement … A-1 4. Special Bilateral Provisions … A-2 Table A-1. Bilateral Agreements That Provide for Acceptance of an Export C of A for Used Aircraft … A-4

Appendix B. Program Letter for Experimental Aircraft

1. General … B-1 2. Description of the Intended Operation(s) and How It Meets the Desired Purpose … B-1 Figure B-1. Sample R&D/Exhibition/PAO Applicant Program Letter for a Special Airworthiness Certificate … B-6

Appendix C. Procedures for Issuing Operating Limitations

Table C-1. Operating Limitations … C-4

Appendix D. Issuance of U.S. Standard Airworthiness Certificates for New Aircraft Manufactured Outside the United States

1. Purpose … D-1 2. Applicability … D-1 3. Procedure … D-1 4. Administrative Requirements … D-8

Appendix E. Forms Listing and Availability

Table E-1. Available Forms … E-1

Appendix F. Acronyms … F-1

Appendix G. Definitions … G-1

xii

Table of Contents (Continued)

Paragraph Page

Appendix H. Administrative Information

1. Distribution … H-1 2. Authority to Change This Order … H-1 3. Deviations … H-1 4. Suggestions for Improvements … H-1 5. Records Management … H-1

Appendix I. FAA Form 1320-19, Directive Feedback Information … I-1

xiii

Chapter 1. Introduction

100. Purpose of This Order. This order establishes procedures for accomplishing original and recurrent airworthiness certification of aircraft and related products and articles.

Chapter 1. Introduction

101. Audience. Federal Aviation Administration (FAA) aviation safety inspectors (ASI) and persons or organizations delegated authority to issue airworthiness certificates and related approvals.

102. Where Can I Find This Order. You can find this order on the MyFAA Employee website or the FAA public website at http://www.faa.gov/regulations_policies/orders_notices/. This order is also available on the FAA’s Regulatory and Guidance Library website at http://rgl.faa.gov/.

103. Explanation of Policy Changes. This revision—

a. Clarifies the terms “original” and “recurrent,” as related to airworthiness certification or approvals.

b. Provides additional information about program letters included with the application for a special airworthiness certificate and former military aircraft.

c. Incorporates changes to chapter 4, section 10, Certification and Operation of Aircraft Under the Experimental Purpose of Exhibition or Air Racing.

d. Incorporates numerous changes originating from input through the directive feedback system.

e. Incorporates changes to several sections related to the issuance of operating limitations.

104. Cancellation. The following are cancelled upon the effective date of this order:

a. FAA Order 8130.2G, Airworthiness Certification of Aircraft and Related Products, dated August 31, 2010.

b. All clarification or deviation memorandums issued for FAA Order 8130.2, and all previous revisions dated February 4, 2015 or earlier.

c. FAA Order 8130.20, Registration Requirements for the Airworthiness Certification of U.S. Civil Aircraft, dated December 24, 1990.

d. FAA Order 8130.29A, Issuance of a Special Airworthiness Certificate for Show Compliance and/or Research and Development Flight Testing, dated June 29, 2007.

e. FAA Order 8130.31, Issuance of Special Airworthiness Certificates for Replicas of the 1903 Wright Flyer Aircraft, dated April 2, 2003.

105. Effective Date. This order is effective March 31, 2015.

Section 1. General Information

Chapter 2. General Policies and Procedures

Section 1. General Information

200. Definition of the Term “Airworthy” for U.S. Type-Certificated Aircraft. The FAA must find that an aircraft is airworthy before issuing an airworthiness certificate. Two conditions must be met for an aircraft to be considered “airworthy.” Title 49 of the United States Code (49 U.S.C.) 44704 and Title 14 of the Code of Federal Regulations (14 CFR) part 21, Certification Procedures for Products and Parts, state the conditions necessary for issuance of an airworthiness certificate:

a. The aircraft must conform to its type design. For the purpose of airworthiness, conformity to the type design is considered attained when the aircraft configuration and the engine, propeller, and articles installed are consistent with the drawings, specifications, and other data that are part of the type certificate (TC). This includes any supplemental type certificate (STC) and repairs and alterations incorporated into the aircraft.

b. The aircraft must be in a condition for safe operation. This refers to the condition of the aircraft relative to wear and deterioration, for example, skin corrosion, window delamination/crazing, fluid leaks, and tire wear.

Note 1: If either of these conditions are not met, the aircraft is not considered airworthy.

Note 2: Aircraft presented for the issuance of a certificate under § 21.191 do not need to conform to their type design, but must be in a condition for safe operation.

201. Representatives of the FAA Authorized to Issue Airworthiness Certificates and Related Approvals.

a. Consistent with applicable Aircraft Certification Service (AIR) policies and instructions, an FAA manufacturing or airworthiness ASI is authorized to issue airworthiness certificates and related approvals covered in this order.

b. The FAA is authorized under part 183, Representatives of the Administrator, to designate private persons or organizations to act as representatives of the Administrator to issue airworthiness certificates and related approvals. A designated manufacturing inspection representative (DMIR) or designated airworthiness representative (DAR) may issue standard and special airworthiness certificates, airworthiness approvals, and export approvals, and may perform certain other examinations, inspections, and testing services relative to certification functions in the areas of manufacturing and maintenance. ASI certification functions will be delegated to the fullest extent practical, but not to the extent an advisor’s technical skills are jeopardized. The designee’s Certificate of Authority must specify the type and limitation of authority granted.

c. The FAA is authorized under part 183, subpart D, Organization Designation Authorization, to delegate specific functions to organizations on behalf of the FAA related to engineering, manufacturing, operations, airworthiness, or maintenance for the purpose of issuing airworthiness certificates and related approvals. Refer to FAA Order 8100.15, Organization Designation Authorization Procedures, for further information on organization designation authorizations (ODA).

202. Responsibilities of FAA ASIs and Designees.

a. The procedures in this order cover original airworthiness certification for which FAA manufacturing ASIs are primarily responsible, and recurrent airworthiness certification for which FAA airworthiness ASIs are primarily responsible. FAA manufacturing and airworthiness ASIs may assist each other by mutual agreement.

b. The FAA designees, within the limits of their authority, are authorized to issue original or recurrent airworthiness certificates and related approvals. They are responsible for determining that the products or articles submitted to them are airworthy and meet any other specified requirements. They also are responsible for the completeness, accuracy, and processing of all official documents and paperwork as provided for in this order. All actions taken by the designees on behalf of the FAA are subject to the monitoring, review, and approval of the supervising ASIs.

c. ASIs are responsible for training and supervising designees assigned to them regarding airworthiness certification procedures and all related documentation. The supervising ASI should also ensure designees have been provided (or have access to) the appropriate regulations, instructions, and forms necessary for the performance of their designated duties.

d. ASIs will supervise and maintain surveillance over the certification activities accomplished by designees to ensure all certifications and approvals comply with the applicable rules, policies, and procedures.

Note: In this order, the term “FAA” or “ASI,” as it relates to airworthiness certification activity, refers to the FAA airworthiness inspector (that is, manufacturing and airworthiness) and that person’s authorized designee. Designees will perform only authorized functions on behalf of their managing office and FAA advisor.

e. Before a designee can issue a special airworthiness certificate or a special flight permit, they should obtain in writing from the geographically responsible (where the certification takes place) Manufacturing Inspection District Office (MIDO), Flight Standards District Office (FSDO), or Certificate Management Office (CMO) that the limitations are acceptable, including any additional limitations and areas of operation the FAA considers necessary for safety.

203. Possession and Display of Airworthiness Certificates. Any airworthiness certificate issued to a U.S.-registered civil aircraft must be displayed at the cabin or cockpit entrance so the certificate is legible to passengers or flightcrew members (part 91, General Operating and Flight Rules, § 91.203(b)).

204. Aircraft Registration. The procedures for aircraft registration and issuance of registration numbers are contained in part 47, Aircraft Registration. The registration of aircraft is not a function of airworthiness certification; however, U.S. registration is a prerequisite for issuance of an airworthiness certificate. The FAA must ensure an aircraft presented for airworthiness certification is properly registered (49 U.S.C. 44704(d) and 14 CFR 21.173). A Certificate of Aircraft Registration (Aeronautical Center Form 8050-3 or 8050-6), query from an official FAA registry database, or email/telephone confirmation from the Flight Standards Service, Aircraft Registration Branch (AFS-750) are acceptable to verify registration. The pink copy of Aeronautical Center Form 8050-1, Aircraft Registration Application, cannot be used to verify registration. If the certificate of aircraft registration does not have an expiration date or if the registration is expired, the aircraft is not eligible for an airworthiness certificate.

205. Size of Aircraft Nationality and Registration Marks.

a. Nationality and registration marks displayed on all aircraft, with the exception of aircraft covered in part 45, Identification and Registration Marking, § 45.29(b)(1)(iii) and (b)(2), must be at least 12 inches high in accordance with § 45.29. However, certain aircraft may display smaller registration marks as identified in § 45.29(b)(1)(i) and (b)(3) until the aircraft are repainted, restored, or changed. Once these aircraft are repainted or the marks are repainted, restored, or changed, 12-inch-high registration numbers must be displayed.

b. FAA inspectors should be alert for newly repainted aircraft registration marks and ensure the marking is consistent with § 45.29. An investigation should be initiated whenever an FAA inspector finds that an aircraft has not been marked with 12-inch-high registration numbers in accordance with § 45.29(b)(1)(i) or (b)(3).

c. Nationality and registration marks of at least 3 inches high may be displayed on an aircraft issued an experimental certificate under § 21.191(d), (g), or (i) to operate as an exhibition aircraft or an amateur-built aircraft, or when the aircraft maximum cruising speed does not exceed 180 knots calibrated airspeed. Marks of at least 3 inches high also may be displayed on airships, spherical balloons, nonspherical balloons, powered parachutes, and weight-shift control aircraft in accordance with § 45.29.

d. When marks include only the Roman capital letter “N” and the registration number is displayed on limited, restricted, light-sport, experimental, or provisionally certificated aircraft, the operator must also display on that aircraft near each entrance to the cabin, cockpit, or pilot station, in letters not less than 2 inches nor more than 6 inches high the words “limited,” “restricted,” “light-sport,” “experimental,” or “provisional,” as applicable per § 45.23.

e. Powered parachute and weight-shift control aircraft must display the marks required by § 45.23. The marks must be displayed horizontally and in two diametrically opposite positions on any fuselage structural member.

206. Display of Nationality and Registration Marks on Antique and Antique Replica Aircraft.

a. Section 45.22(b)(1)(ii) provides, in pertinent part, that small U.S-registered aircraft at least 30 years old, or aircraft that have been issued an experimental certificate for the purpose

of exhibition or operating an amateur-built aircraft and that have the same exterior configuration as a 30-year-old aircraft, may display marks consisting of the Roman capital letter “N” followed by the U.S. registration number or the symbol appropriate to the airworthiness certificate of the aircraft (for example, “C,” standard; “R,” restricted; “L,” limited; or “X,” experimental) followed by the U.S. registration number. The symbol used must be appropriate for the airworthiness certificate of the aircraft being certificated, not the aircraft being replicated.

Example 1: A Great Lakes 2T-1A aircraft manufactured in 1929 is registered in the United States and has been issued nationality and registration mark N1234. The aircraft has been issued a standard airworthiness certificate. The owner/operator may display the mark NC1234 if so desired.

Example 2: An aircraft that has the same exterior configuration as the Great Lakes 2T-1A is registered in the United States and has been issued nationality and registration mark N5678. An experimental airworthiness certificate has been issued under § 21.191(d) or (g). The owner/operator may display the mark NX5678 if so desired.

b. When aircraft are marked as described in § 45.22(b)(1)(ii), the airworthiness and registration certificates will not include the inserted symbol. In example 1 above, the aircraft could be marked NC1234, but the registration and airworthiness certificates would reflect only the N1234.

c. When making a query of the FAA Civil Aviation Registry (FAA Aircraft Registry) computer database, the inserted symbol must be omitted to obtain accurate information concerning the aircraft.

d. In addition, § 45.23(b) provides that when the appropriate symbol is used with the nationality and registration marks in accordance with § 45.22(b)(1)(ii), the word “limited,” “restricted,” or “experimental” is not required to be displayed on the aircraft.

207. Original and Replacement Aircraft Identification Plates.

a. Original Data Plates. Each aircraft presented for airworthiness certification must meet the requirements of § 21.182. Each aircraft, aircraft engine, propeller, propeller blade, and propeller hub manufactured under a TC or production certificate (PC), or an aircraft to be certificated as an amateur-built, primary kit-built, or light-sport aircraft (LSA), must be identified with the information specified in § 45.13. Manned free balloons are required to comply with § 45.11(d).

b. Replacement Data Plates.

(1) When FAA personnel receive inquiries regarding replacement, removal, or destruction of identification (ID) plates, the sample letter in figure 2-2 of this order may be used as a guide for responding.

(2) When a new ID plate is required, the owner or the owner’s authorized representative will contact their local FAA office. The FAA determines whether the request

is valid (refer to paragraph 207d, Misuse of Data Plates, below) and provides a letter to the applicant with the FAA’s finding. If the FAA determines that the request is valid, the applicant includes the FAA letter with their request for the replacement data plate from the appropriate manufacturer.

(3) Upon notification by the applicant, which must include the FAA’s letter, the product manufacturer may then issue the replacement ID plate.

(4) The old ID plate, when available, must be voluntarily surrendered by the owner with a written statement to the FAA office that authorized the replacement. The FAA office must make a copy of the plate and then either physically destroy it or, if requested by the manufacturer, return it to the manufacturer via certified mail. The FAA office must then submit a letter to AFS-750 stating that the surrendered plate has been destroyed. AFS-750 will include the letter in the permanent aircraft records file.

c. Removal of Data Plates. Section 45.13 permits persons performing maintenance operations under part 43, Maintenance, Preventive Maintenance, Rebuilding, and Alteration, to remove an aircraft data plate. The removal must be done in accordance with the methods, techniques, and practices acceptable to the FAA. The ID plate removed may be reinstalled only on the product from which it was removed.

d. Misuse of Data Plates.

(1) ASIs should be on alert for any indication of ID plate misuse or suspicious activity, such as the building of a complete aircraft by a person performing work under part 43. Installation of an ID plate by a person performing work under part 43, where the ID plate has been purchased or salvaged from another aircraft, is not approved unless written approval is obtained from the FAA.

(2) Before issuing an airworthiness certificate for an aircraft that appears to be a repair or restoration of an aircraft that previously has been destroyed or demolished, the ASI should seek the assistance of the manager of AFS-750. That office can assist the ASI in determining whether the serial number of the aircraft on which certification is sought is the serial number of an aircraft previously classified as destroyed or demolished by the FAA or the National Transportation Safety Board (NTSB). If the ASI determines that the ID plate comes from a previously destroyed or demolished aircraft, the ASI must initiate an investigation to determine whether a violation of § 45.13(c) or (e) has occurred before the airworthiness certificate may be issued. If a violation of § 45.13(c) or (e) is found, the ASI must deny the airworthiness certificate and initiate an enforcement action.

Note: When the ID plate is surrendered, it is no longer considered personal property.

e. New Data Plates. The appropriate local MIDO, Manufacturing Inspection Satellite Office (MISO), or FSDO may authorize a builder of an aircraft assembled from spare and/or surplus articles under § 21.6(b) to make a new data plate for that aircraft upon a satisfactory showing that the aircraft is airworthy. However, the office must ensure the aircraft is eligible for an airworthiness certificate as built from spare and/or surplus articles in accordance with

§ 21.6, § 21.183, and paragraph 315 of this order before authorizing the builder to make a data plate. The data plate will be made in accordance with part 45 and affixed to the aircraft before the issuance of any airworthiness certificate.

208. Public Aircraft Operations.

a. Public aircraft are defined in 49 U.S.C. 40102(a)(41).

b. If an applicant intends to perform both public and civil aircraft operations, advise them that when changing from a public status to a civil status, the aircraft must meet all civil requirements. Depending on the complexity of its public operations, it is recommended that an operator have written instructions on how it transitions from public to civil status. For additional information, refer to FAA Order 8900.1, Flight Standards Information Management System (FSIMS), volume 3, chapter 14, and Advisory Circular (AC) 00-1.1, Government Aircraft Operations.

209. Aircraft Being Removed From a Continuous Maintenance System.

a. No change in the airworthiness certificate is required if the aircraft has a current FAA Form 8100-2, Standard Airworthiness Certificate.

b. Operators of aircraft previously operated under 14 CFR part 121, Operating Requirements: Domestic, Flag, and Supplemental Operations, or part 91, subpart D, Special Flight Operations, and intending to operate the aircraft under part 91, must select, identify, establish, and use an inspection program as prescribed in § 91.409(e), (f), (g), and (h).

c. It also is important for the operator to know the current status of the aircraft relative to applicable requirements; for example, (1) weight and balance data, (2) the flight manual appropriate to the operation, (3) time on life-limited components, and (4) compliance with airworthiness directives (AD). Some carriers have exemptions or adjusted AD compliance times.

210. Operation of Civil Aircraft With a Door Open or Removed for Parachuting, Skydiving, or Other Special Operations.

a. Owners or operators who are interested in obtaining authorization for operation of aircraft with a door open or removed for parachuting or other special operations must forward a written request to the FSDO having jurisdiction over the area in which the operations are to be conducted. The request must contain the following information:

(1) Name and address of the registered aircraft owner;

(2) Make, model, serial, and registration number of the aircraft;

(3) Location where the aircraft normally is based; and

(4) Reason for the aircraft to be operated with a door removed.

b. Aircraft may be approved to operate with a door open or removed by TC, amended TC, STC, authorization in the aircraft’s flight manual, or field approval.

(1) Aircraft approved by TC, amended TC, STC, or approved flight manual authorization do not require any additional limitations or authorization from the FSDO.

(2) Aircraft approved to operate by issuance of FAA Form 337, Major Repair and Alteration, must have operating limitations issued. Sample operating limitations are outlined in figure 2-3 of this order. Field approval guidance is in FAA Order 8900.1. The ASI must note on the operating limitations the aircraft make, model, registration and serial number, type of operation authorized, date of issuance, ASI’s name, and district office number. On an aircraft that requires removal or opening of a particular door, the ASI must specify in the limitations which door may be removed or opened.

Note: A copy of the limitations must be forwarded to AFS-750.

c. Removal or installation of a cabin door for the specified aircraft is considered maintenance and as such must be accomplished by persons authorized under § 43.3.

d. If operations of rotorcraft with the doors opened or removed obstructs the nationality and registration marks from view, the operator must notify the appropriate managing office in writing detailing the nature of the proposed operation and the proposed dates of operation with doors removed. The managing office will then instruct the operator to affix temporary nationality and registration marks on an authorized surface required by § 45.27(a). The size of the marks must comply with § 45.29(b) unless no authorized surface is large enough for display of marks meeting the size requirements of this section. The rotorcraft would then be marked on the largest authorized surface with marks as large as practicable, as allowed by § 45.29(f). Any remnants of the permanent nationality and registration marks must be obliterated so as not to confuse identification of the rotorcraft with temporary markings. The temporary markings must be able to endure flight operations in various weather conditions. Flight operations must be authorized in writing by the managing office for a specified time and purpose. The managing office will verify the temporary markings comply with part 45 and that the rotorcraft is returned to its permanent marking scheme.

e. Under appendix A to part 43, paragraph (c)(15), a pilot may be authorized to remove or reinstall passenger seats. Removal or installation of control sticks and wheels must be performed in accordance with the applicable sections of part 43.

211. Banner Towing. An aircraft that is airworthy and has an FAA-approved banner tow installation may be operated under a standard airworthiness certificate for banner towing purposes. An aircraft that has a standard airworthiness certificate and is modified for a special purpose operation must be operated under a multiple airworthiness certificate (standard/restricted) when the following conditions occur:

a. The special purpose modification is not approved for standard category use.

b. The aircraft will be operated outside the normal category operating limitations.

212. Former Military Aircraft.

a. Eligibility. Former military aircraft may be eligible for a standard airworthiness certificate or an airworthiness certificate in the restricted or limited category. If a TC has not been issued for the aircraft, it may be eligible for an experimental airworthiness certificate for the purpose of research and development (R&D), crew training, exhibition, or air racing.

b. High-Performance Former Military Aircraft. Some former military aircraft have inherent high risk factors associated with their design, manufacture, maintenance, and operation. These high risk factors must be mitigated. Some aircraft may have high risk factors that may be difficult to mitigate, and consequently may not be eligible for an airworthiness certificate.

c. Demilitarization of Former Military Aircraft. The demilitarization process most likely will involve a change to the aircraft configuration so FAA representatives will not process an application for airworthiness certification unless demilitarization is complete.

(1) The FAA may require that some systems be removed or disabled to establish a condition for safe operation for the intended use. For example, safe operation of guns, cannons, targeting radars, electronic jammers, jettisonable stores, or explosive devices may not be feasible under or consistent with the intended experimental purpose. Potential safety hazards related to these systems include accidental firing of guns, accidental release of stores, accidental operation of radars on the ground, compartment fires, and damage to the airframe. These hazards may pose risks to other aircraft and to persons and property on the ground and may not be able to be adequately mitigated via operating limitations. Although some of these systems may be required to support a valid R&D purpose, the applicant and the ASI need to understand the corresponding safety risks and work closely together to determine the feasibility of mitigating these risks via additional operating limitations.

(2) Former military aircraft imported from any other country require an import permit issued by the Department of Justice, Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF). This permit is granted by the ATF using ATF Form 6, Application and Permit for Importation of Firearms, Ammunition, and Implements of War. In addition, these former military aircraft are required to be demilitarized to clear U.S. Customs and Border Protection. Compliance with demilitarization is evidenced by a completed ATF Form 6A, Release and Receipt of Imported Firearms, Ammunition, and Implements of War. Proof of demilitarization will be verified if the applicant presents copies of ATF Form 6 and ATF Form 6A that have been completed by appropriate officials of the Department of Justice. If the applicant is unable to produce ATF Form 6 or ATF Form 6A for original certification of the aircraft, deny the application.

Note 1: For any questions regarding ATF Form 6 or ATF Form 6A requirements, contact the ATF Firearms and Explosives Imports Branch at the Department of Justice.

Note 2: For an aircraft to be eligible for an airworthiness certificate, it must be listed as an aircraft on the U.S. Customs documentation. For example, if an aircraft is imported as scrap, parts, or a museum piece, it is not eligible for an airworthiness certificate.

(3) For additional information on what items and components are part of the aircraft’s weapons system, refer to aircraft maintenance manuals and the related weapons delivery manual. Some aircraft manufacturers may offer guidance on aircraft demilitarization. Some of these systems could be permitted for an experimental R&D certificate, but the related safety issues still have to be addressed, particularly if the aircraft also has an experimental certificate for another purpose. U.S. Air Force Technical Order 00-80G-1, Make Safe Procedures for Public Static Display, can be used as a reference.

213. Aircraft Equipped With Explosive Devices or Jettisonable Stores. These types of systems are usually associated with former military aircraft.

a. Airport. An applicant for an experimental certificate must provide objective evidence that the manager of the airport where the aircraft is based has been notified regarding both the presence of jettisonable stores and any explosive devices and the planned operation of the aircraft from that airport.

b. Serviceability of Jettisonable Stores. Jettisonable external fuel tanks or stores systems must be maintained in accordance with the manufacturer’s procedures and inspected in accordance with the provisions of the inspection program for the particular aircraft. Only aircraft with a certificate for the purpose of R&D may be operated with functional jettisonable external fuel tanks or stores, and only for testing those stores for aircraft controllability and release. When the testing of the external stores is complete, the stores must be removed or secured so they cannot be jettisoned. The jettisonable systems may only be operational for the time period required for testing those systems. When the jettisonable systems are operational, the aircraft operation must be restricted to a geographical area that meets the requirements of § 91.305, and prohibited from flying over densely populated areas at all times.

c. Ejection Seat System. Ejection seat systems must be maintained in accordance with either the manufacturer’s procedures or the procedures specified by a military service using that aircraft model. An ejection seat system may not be modified without approval of the seat or aircraft manufacturer. The ejection seat system must be approved for use in the aircraft by the manufacturer, or by a military service using that aircraft model. The FAA will verify there is a record entry indicating current serviceability of the ejection system, including the status of any dated shelf life articles.

d. Securing Procedures. The applicant must have provisions for securing the aircraft to prevent inadvertent operations of systems that use an explosive device whenever the aircraft is parked.

Section 2. Airworthiness Certificates

e. Marking of Explosive Devices. The applicant must have provisions that provide for clear marking and identification of all explosive devices used in any aircraft system. Aircraft markings must be applied externally and indicate that the aircraft is equipped with explosive devices. An airworthiness certificate will not be issued until meeting this requirement.

214. Reserved.

Section 2. Airworthiness Certificates

215. General. FAA Form 8100-2 and FAA Form 8130-7, Special Airworthiness Certificate, will be referred to as being either a standard or a special classification within this order.

216. Classification and Category of Airworthiness Certificates.

a. Standard Classification. FAA Form 8100-2 may be issued for an aircraft that fully complies with all of the requirements for a standard airworthiness certificate in the category of normal, utility, acrobatic, commuter, or transport category, manned free balloons, or any other special classes of aircraft designated by the FAA.

b. Special Classification. FAA Form 8130-7 may be issued for an aircraft that does not meet the requirements for a standard airworthiness certificate. The certificate may be issued for an aircraft that meets the following:

(1) Primary. Aircraft that satisfies the requirements of § 21.184.

(2) Restricted. Aircraft that satisfies the requirements of § 21.185.

(3) Limited. Aircraft that satisfies the requirements of § 21.189.

(4) Provisional. Aircraft that satisfies the applicable requirements of part 21, subpart C, Provisional Type Certificates, and subpart I, Provisional Airworthiness Certificates.

(5) Light-Sport. Aircraft that meets the requirements of § 21.190.

(6) Experimental. Aircraft that meets the requirements of § 21.191.

(7) Special Flight Permits. FAA Form 8130-7 may be issued for an aircraft that does not currently meet applicable airworthiness requirements, but is capable of safe flight, and meets the requirements of §§ 21.197 and 21.199.

217. Replacement, Exchange, or Amendment of Airworthiness Certificates.

a. Replacement.

(1) The FAA may issue a replacement airworthiness certificate when a certificate is declared lost, has been mutilated, is no longer legible, or contains inaccurate and/or erroneous information. The replacement airworthiness certificate must carry the original issue date of the certificate being replaced, preceded by a capital “R” in the Date block of the certificate. Replacement certificates also will be issued when the aircraft registration number has been

changed, and the ASI must forward a copy of the replacement certificate and a copy of the Aeronautical Center Form 8050-64, Assignment of Special Registration Numbers, to AFS-750. In these cases, a new application for airworthiness certification is not required. When issuing a replacement for a special airworthiness certificate, the operating limitations that were on the original certificate will be reissued. The only modification to the limitations allowed is for administrative corrections.

(2) Request for a replacement certificate will be made to the local FAA office or, for air carriers, to the applicable certification office. The registered owner or certificate operator will certify this by submitting a signed statement containing the registration number (N-Number), serial number, make, and model of the aircraft, and a reason the replacement certificate is needed. Replacement of airworthiness certificates must not be accomplished by verbal agreement with the assigned ASIs or through procedures contained in air carriers’ manuals that allow the continued operation of an aircraft without an airworthiness certificate. Such actions are contrary to §§ 91.203(b), 121.153(a)(1), and 135.25(a)(1).

(3) A replacement airworthiness certificate may be issued without supporting documentation from AFS-750 if the date of issuance and the airworthiness classification and/or category of the lost or mutilated certificate can be positively established from the aircraft records, or from the remains of the certificate. If there is insufficient data on which to base issuance of the replacement certificate, the ASI will obtain the required data electronically, by telephone, or by mail (such as the application form or previously issued airworthiness certificate) from AFS-750.

(4) Before issuing a replacement certificate, the FAA must review the aircraft records and, if necessary, inspect the aircraft to ensure the applicant’s request is justified and the aircraft is eligible for the airworthiness certificate requested.

(5) Both a copy of the replacement certificate and a copy of the registered owner’s or certificate operator’s request for a replacement certificate (refer to paragraph 217a(2) of this order) or an Aeronautical Center Form 8050-64 (refer to paragraph 217a(1) of this order) must be forwarded to AFS-750.

b. Amendment.

(1) A standard or special airworthiness certificate may be amended when there is—

(a) A modification to the aircraft, such as one that has been approved by an STC or amended TC, that changes the category of the aircraft specified in block 4 of the standard airworthiness certificate.

(b) A change to the exceptions specified in block 5 of the standard airworthiness certificate.

(c) A change in the aircraft model specified in block 2 of the standard airworthiness certificate.

(d) A change in the operating limitations for an aircraft with a special airworthiness certificate.

(e) A change in the aircraft model specified in block “D” of the special airworthiness certificate for those aircraft that have been issued a TC (for example, restricted, primary, limited).

(2) When a certificate is amended, the issuance date will be the current date. Also, the capital letter “A” will be typed in front of the date.

(3) Any amendment of an airworthiness certificate will require submission of FAA Form 8130-6, Application for U.S. Airworthiness Certificate. Refer to paragraph 801 of this order for instructions on completing this form.

(4) Paragraph 219 of this order details further information on aircraft model changes.

(5) Operating limitations that were issued based on a previous edition of this order will be updated to include limitations contained in the current edition. The FAA does not require a new aircraft certification inspection for this type of administrative paperwork amendment.

c. Exchange. It is highly desirable that all aircraft currently certificated in the standard category carry FAA Form 8100-2 to be consistent with the regulations. Owners and operators of general aviation and air carrier aircraft that still have FAA Form 1362A, Certificate of Airworthiness, should be encouraged to exchange such forms for the standard airworthiness certificate, FAA Form 8100-2. In exchanging these certificates, the operating certificate number will not be entered on the revised form. FAA Form 1362A will be attached to and forwarded with a copy of the revised certificate to AFS-750 to establish an official record of the exchange action. The foregoing exchange procedure also applies to FAA Form 8130-7, instead of FAA Form 1362B, Certificate of Airworthiness. The new airworthiness certificate will reflect the date as indicated on FAA Forms 1362A or 1362B, preceded by a capital “E” in the Date block of the certificate. The procedure to exchange a Certificate of Airworthiness (C of A) (ACA-1362 (12-50)) does not apply to an expired C of A issued before July 17, 1956. Block 4 of FAA Form 1362 indicates the date of expiration. Refer to the procedures in chapter 3 of this order for a standard airworthiness certificate.

218. Surrendered Airworthiness Certificate.

a. Airworthiness certificates voluntarily surrendered by written authorization from an aircraft owner or authorized representative must state why the certificate is being surrendered. The authorization and certificate must be forwarded to AFS-750 for retention in the permanent airworthiness files for that aircraft.

b. The airworthiness certificate must be surrendered to the FAA by the aircraft owner or operator as specified in § 21.335(e) when—

(1) The title of a U.S.-owned aircraft passes or has passed to a purchaser in another country, or

(2) The aircraft is leased for operations, registered in another country, and is removed from the U.S. registry.

219. Aircraft Model Change.

a. When an aircraft has been modified to conform to another model of the same make, the aircraft registration, airworthiness certificate, and aircraft ID plate must reflect the new model designation.

b. In addition to the existing ID plate, a new fireproof ID plate as specified in § 45.13 to include the new model designation must be attached as close as physically possible to the original ID plate without obscuring it.

c. To maintain an accurate and continuous operating history for the aircraft, the original ID plate must not be altered in any manner.

d. The normal procedures, including any applicable inspections, apply when processing FAA Form 8130-6. The amended airworthiness certificate will be identified with a capital “A” preceding the current date of the certificate being issued. If ownership of the aircraft has not changed, an application for aircraft registration, reflecting the new model designation, need not be submitted. AFS-750 will issue an amended registration certificate.

220. Recording of Conformity Inspections. FAA Form 8100-1, Conformity Inspection Record, must be used to document conformity inspections during type, production, and airworthiness certification programs (refer to figure 2-4 of this order). FAA Form 8100-1 must be prepared in accordance with the instructions shown on the back of the form.

221. Airworthiness Certification of Manned Free Balloons. Manned free balloons are type-certificated as complete aircraft consisting of three major articles: the envelope, the burner and fuel system, and the basket. The burner and fuel system and basket also are known as the “bottom-end” articles. Airworthiness certificates will not be issued for any individual article. The following are situations that may be encountered in certificating balloons in the standard category:

a. An applicant for a standard airworthiness certificate must present a complete system (three major components) for the purpose of making a determination of airworthiness.

b. Many balloon type certificate data sheets (TCDS) require each individual balloon envelope to be assigned an individual aircraft serial number, aircraft data plate, and aircraft registration number. As such, the balloon manufacturer obtains a registration number from the FAA Aircraft Registry, assigns the N-Number to the aircraft, and reports the aircraft model and serial number to the FAA Aircraft Registry. When an eligible envelope is mated with the necessary articles to make a complete aircraft as described in the applicable TCDS, it is eligible for a standard airworthiness certificate.

c. Manufacturers of manned free balloons may deliver a balloon envelope when the envelope is the only article ordered. A balloon envelope that is manufactured, assembled to a burner and basket, and flight tested is eligible for a standard airworthiness certificate.

Section 3.

The envelope, along with the standard airworthiness certificate and the logbook, may be delivered without the burner and basket. The envelope may then be assembled to a different burner and basket in accordance with the TC. A person may accomplish the interchange of the burner and basket as a preventive maintenance task as described below.

d. A new airworthiness certificate is not required when the aircraft is disassembled and a different burner and basket combination is installed, as allowed by the TC. Reassembly of the envelope and bottom-end articles into a complete aircraft may be performed as preventive maintenance under part 43, appendix A, paragraph (c)(27). The aircraft records must properly reflect the installation of the bottom-end articles and record the new empty weight. The bottom-end components must be in a current “annual or 100-hour” inspection status. The individual records of the bottom-end articles must be maintained. The due date of the next required inspection is determined based on the time the articles are due for inspection.

e. If an envelope is provided only as a replacement article without obtaining a new aircraft serial number, registration number, or ID plate, the installation of the replacement envelope is a maintenance item under part 43. This requires appropriate documentation of the work performed and a return to service entry in the aircraft records by a person authorized to perform the maintenance. The aircraft ID plate, serial number, and registration number are carried over from the previous aircraft envelope.

f. For model changes, refer to paragraph 219 of this order.

222.-223. Reserved.

Section 3. Initial or Subsequent Issuance of Airworthiness Certificates

(Original/Recurrent) or Related Approvals

224. General. This section clarifies the terms “original” and “recurrent” as related to the issuance of airworthiness certificates or approvals. Also identified in this section are the FAA offices responsible for performing such functions, including, as appropriate, the cross-utilization of FAA inspection personnel.

a. A variety of airworthiness functions are performed by the FAA. Many of these functions must be accomplished by or coordinated with FAA manufacturing or airworthiness ASIs who have expertise in the particular specialty. These ASIs may include the principal ASI for a major aircraft manufacturer, or the principal maintenance or avionics ASI for an air carrier with aircraft of the same type and complexity as the one for which certification is requested. A number of airworthiness functions can be accomplished by cross-utilization of the FAA. Cross-utilization by the FAA must be employed whenever possible in accordance with the guidance contained in this section.

b. The terms “original” and “recurrent” distinguish between those functions for which FAA manufacturing ASIs have primary responsibility and those for which FAA airworthiness ASIs have primary responsibility.

c. The FAA manufacturing ASI has primary responsibility for the issuance of original airworthiness certificates and approvals. Original certification requires determining that the

products and articles were properly manufactured. The FAA airworthiness ASI has primary responsibility for the issuance of recurrent airworthiness certificates and approvals. Recurrent certification requires determining that the product has been properly maintained or altered while in service.

225. Airworthiness Certification.

a. Original Certification. The term “original certification” applies to the issuance of standard or special airworthiness certificates and approvals, including FAA Form 8130-4, Export Certificate of Airworthiness, for aircraft holding a U.S. TC for the following:

(1) Aircraft or related products and articles that have never held a U.S. airworthiness certificate, except for a special flight permit, or a U.S. Export C of A.

(2) Aircraft or related products and articles that have never held an airworthiness certificate or Export C of A issued by a foreign civil aviation authority (CAA) verifying conformity to the U.S. type design under a bilateral agreement.

(3) Aircraft involved in a certification project such as developing a TC or STC.

b. Recurrent Certification. The term “recurrent certification” applies to the issuance of standard or special airworthiness certificates or approvals for products and articles that do not meet the original certification criteria listed above.

226. Exceptions.

a. Any requests, original or recurrent, for a special airworthiness certificate for LSA, amateur-built, exhibition, R&D, market survey, crew training, air racing, or special flight permit for new aircraft may be handled by FAA manufacturing ASIs, FAA airworthiness ASIs, or their authorized designees. If the responsible office cannot support the certification request, an appropriate delegation should be coordinated with the alternate office.

b. Any requests, original or recurrent, for an experimental certificate showing compliance with the regulations is the primary responsibility of the FAA manufacturing ASI or authorized designee. In remote areas or under special circumstances, an FAA airworthiness ASI may be delegated the authority by AIR if it is established that the person has had experience in type certification programs of a type and complexity comparable to the certificate requested.

c. If a FSDO receives an application for an original airworthiness certification, that FSDO must contact the responsible MIDO to determine if the MIDO will process the application or pass on this responsibility to the FSDO. Similarly, if a MIDO receives an application for a recurrent airworthiness certification, the MIDO must coordinate with the responsible FSDO to determine if the FSDO will process the application or pass on this responsibility to the MIDO.

227. Recording of Conformity Inspections. All inspections conducted by an ASI or designee to determine conformity to an approved type design before an airworthiness certificate is issued must be recorded on FAA Form 8100-1 (refer to paragraph 220 of this order).

228. Eligibility and Evaluation of U.S. Military Surplus Flight Safety-Critical Aircraft Parts (Articles) (FSCAP), Engines, and Propellers.

a. General.

(1) This paragraph provides guidance for use in evaluating and determining the eligibility of U.S. military surplus FSCAPs, engines, and propellers for installation on FAA type-certificated products. Many military surplus FSCAPs have the potential to be approved for installation on aircraft that hold special or standard airworthiness certificates.

(2) Military engines, propellers, and articles are categorized as new or used and fall into one of the following categories:

(a) Dual-use FSCAPs;

(b) Military-unique FSCAPs;

(c) Dual-use military surplus engines, propellers, and articles; and

(d) Military-unique surplus engines, propellers, and articles.

(3) Before these military engines, propellers, and articles are installed on type-certificated products, the installer must determine that they are—

(a) Eligible for installation, and

(b) Airworthy.

(4) There are certain unique design considerations and FAA certification requirements for engines and propellers. Therefore, the eligibility and evaluation processes for military surplus engines, propellers, and articles are described separately in paragraph 228d of this order.

Note: For eligibility and evaluation of non-flight safety-critical articles, safety-critical aircraft articles, engines/propellers, and their articles, use AC 20-62, Eligibility, Quality, and Identification of Aeronautical Replacement Parts.

b. Dual-Use FSCAP (New or Used).

(1) Eligibility Screening. New or used dual-use FSCAPs may be eligible for installation on FAA type-certificated products with standard or special airworthiness certificates. The eligibility determination is made based on a review of the following pertinent Department of Defense (DOD) historical records:

(a) FSCAP identification: part number, DOD National Stock Number, and serial number.

(b) Manufacturer, DOD Commercial and Government Entity (CAGE) code, and date of manufacture.

(c) Total time-in-service.

(d) Current status of life-limited FSCAPs.

(e) Time since the last overhaul of each FSCAP that is required to be overhauled on a specified time basis.

(f) Identification of current inspection status, including time since last required inspection or maintenance performed.

(g) Current status of applicable AD and DOD directives (for example, engineering changes, technical orders, or maintenance work orders) including the date and method of compliance. If the AD involves recurring action, the current status includes the time and date when the next action is required.

(h) A list of current major alterations, repairs, or modifications for each FSCAP.

(i) Date any work was accomplished.

(j) Work authentication.

(2) Airworthiness Determination. After determining the FSCAP is eligible to be installed on a type-certificated product, the FSCAP must be evaluated to determine whether it is airworthy.

(a) New Dual-Use FSCAP.

1 For an FSCAP to be installed on products with standard airworthiness certificates, the FSCAP must be airworthy.

2 For an FSCAP to be installed on products with special airworthiness certificates, the FSCAP must be cited in the FAA-accepted maintenance manual and illustrated parts catalog (IPC) specified on the applicable TCDS, and must be in a condition for safe operation.

(b) Used Dual-Use FSCAP.

1 For an FSCAP to be installed on products with standard or special airworthiness certificates, the FSCAP must be evaluated using the procedures for new dual-use FSCAPs above, as appropriate, to determine the FSCAP’s airworthiness in accordance with § 43.13.

2 The FSCAP also must be evaluated by persons authorized under § 43.7(a), (c), (d), or (e) by using the following applicable methods, means, or data sources:

(aa) Differences between military and civil versions (for example, possible DOD modifications, alterations, or repairs performed);

(bb) Current manufacturer or DOD technical data and procedures to perform tests and inspections, including current life-limited articles list;

(cc) Comparison of military time and/or cycle count for accumulated operational time versus civil (for example, “Did the military use a different method than civil operators to account for accumulated operational time?”);

(dd) Nondestructive tests, as required;

(ee) Bench test or functional test, as required;

(ff) Results of tests and inspections recorded;

(gg) Complete historical and modification, alteration, or repair records;

(hh) Manufacturer’s ID plate;

(ii) Flight, maintenance, and/or structural manual(s), and IPC; and

(jj) Instructions for Continued Airworthiness (ICA).

(3) Approval for Installation. Persons authorized under § 43.7 may approve dual-use FSCAPs for installation on type-certificated products if the FSCAP successfully completed the eligibility screening and airworthiness evaluation. The installer must be able to determine that the installation of the FSCAP will leave the product in compliance with all regulations and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

c. Military-Unique FSCAP.

(1) Eligibility Screening. New or used military-unique FSCAPs may be eligible for installation on civil aircraft with special airworthiness certificates under § 21.305(c) in conjunction with type certification procedures for a product or in accordance with a TCDS. Military-unique FSCAPs are not eligible for installation on a civil aircraft with a standard airworthiness certificate. The eligibility determination is made based on a review of the following pertinent DOD historical records:

(a) FSCAP identification: part number, DOD National Stock Number, and serial number.

(b) Manufacturer, DOD CAGE code, and date of manufacture.

(c) Total time-in-service.

(d) Current status of life-limited FSCAPs.

(e) Time since the last overhaul of each FSCAP that is required to be overhauled on a specified time basis.

(f) Identification of current inspection status, including time since last required inspection or maintenance performed.

(g) Current status of applicable ADs and DOD directives, (for example, engineering changes, technical orders, or maintenance work orders) including the date and method of compliance. If the AD involves recurring action, the current status includes the time and date when the next action is required.

(h) A list of current major alterations, repairs, or modifications for each FSCAP.

(i) Date any work was accomplished.

(j) Work authentication.

(2) Airworthiness Determination. After determining the FSCAP is eligible to be installed on a type-certificated product with a special airworthiness certificate, the FSCAP must be evaluated to determine whether it is airworthy.

(a) New Military-Unique FSCAP. The FSCAP must be cited in the FAA-accepted, military-approved maintenance manual and IPC specified on the applicable aircraft TCDS and must be in a condition for safe operation.

(b) Used Military-Unique FSCAP.

1 The FSCAP must be cited in the FAA-accepted, military-approved maintenance manual and IPC specified on the applicable aircraft TCDS and must be in a condition for safe operation.

2 The FSCAP also must be evaluated to determine airworthiness in accordance with § 43.13, by using the following applicable methods, means, or data sources:

(aa) Special equipment or test apparatus, as required;

(bb) Current manufacturer or DOD technical data and procedures to perform tests and inspections;

(cc) Comparison of military time and/or cycle count for accumulated operational time versus civil time (for example, “Did the military use a different method than civil operators to account for accumulated operational time?”);

(dd) Nondestructive tests, as required;

(ee) Bench test or functional test, as required;

(ff) Results of tests and inspections recorded;

(gg) Complete historical and modification, alteration, or repair records;

(hh) Manufacturer’s ID plate;

(ii) Flight, maintenance, and/or structural manual(s), and IPC; and

(jj) ICA.

(3) Approval for Installation. Persons authorized under § 43.7 may approve military-unique FSCAPs for installation on type-certificated products if the FSCAP successfully completed the eligibility screening and the airworthiness evaluation. The installer must be able to determine that the installation of the FSCAP will leave the product in compliance with the TCDS and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

d. Dual-Use and Unique Military Surplus Engines, Propellers, and Their Articles.

(1) New, used, or parted-out military surplus engines, propellers, and articles should not be presumed to be eligible for installation on FAA type-certificated aircraft. Military surplus engines, propellers, and articles are either dual-use or military-unique.

(2) The pertinent accompanying historical records documentation is essential for—

(a) The Defense Reutilization and Marketing Office’s (DRMO) public sale of engines, propellers, and articles;

(b) Categorizing the engines, propellers, and articles as dual-use or military-unique; and

(c) Establishing the eligibility and airworthiness of the engine, propeller, and articles.

(3) Military surplus engines and propellers may be type certificated under § 21.17, which requires issuance of a new TC and compliance with the applicable requirements, such as part 33, Airworthiness Standards: Aircraft Engines, for engines and part 35, Airworthiness Standards: Propellers, for propellers. For a military aircraft issued a TC under § 21.25 or § 21.27, the applicable engine or propeller is not required to be issued a separate TC. However, it should be noted that the engine and propeller cannot be certificated separately under these two sections. Any eligible military surplus engines or propellers will be referenced on the aircraft’s TCDS. However, military-unique surplus engines, propellers, and articles may be eligible for installation only on civil military surplus aircraft with special airworthiness certificates.

(4) Engines, propellers, and articles are deemed flight safety-critical if their failure, malfunction, or absence could cause a catastrophic failure resulting in loss or serious damage to the aircraft or an uncommanded engine shutdown resulting in an unsafe condition. Such conditions include, but are not limited to, release of engine or propeller debris, propeller separation, and, in rotorcraft, a transient or continuous power loss, or loss of power response. Examples of flight safety-critical engine and propeller articles are life-limited articles, rotating articles, and, for rotorcraft, actuating articles.

(5) Dual-Use Military Surplus Engines, Propellers, and Articles. Dual-use military surplus engines and propellers that hold a TC, and their articles, may be eligible for installation on civil products in accordance with the applicable regulations. The authorized individual completing the eligibility screening and/or the airworthiness evaluation should make a record entry to document the result(s).

(a) Eligibility Screening. New or used dual-use engines, propellers, and articles may be eligible for installation on FAA type-certificated civil or surplus military aircraft with standard or special airworthiness certification. A U.S. TC must have been issued for a corresponding civil model engine or propeller under § 21.21 at the time of manufacture, or a U.S. aircraft TC must have been issued and the engines or propellers referenced in the aircraft TCDS under § 21.27 or § 21.25. The eligibility determination is made based on a review of the following pertinent historical records:

1 Engine, propeller, and article ID (article part number and serial number and manufacturer).

2 Contract or purchase order number under which the engine, propeller, or article was manufactured.

3 Evidence of engine, propeller, and article status, for example, serviceable or unserviceable, in accordance with DOD Form (DD Form) 1574-1, Serviceable Label - Materiel, or Department of the Army (DA) Form 2410, Component Removal/Repair/Install/Gain/Loss Record.

4 Complete historical records maintained by the military, the manufacturer, and any other prior owner(s), pertaining to inspection, modification, repair, alteration, maintenance, and operation of the engine from the time of acceptance by the military, including, but not limited to, DA Form 2408-5, Equipment Modification Record, and DA Form 2408-16, Aircraft Component Historical Record. The maintenance records should also include the date on which the work was accomplished and work authentication.

5 Current status of applicable ADs and DOD directives (for example, engineering changes, technical orders, or maintenance work orders) including the date and method of compliance; and, if the AD involves recurring action, the time and date when the next action is required.

(b) Airworthiness Determination. After determining the article is eligible to be installed on a type-certificated product, the article must be evaluated to determine whether it is airworthy.

1 New Dual-Use Engines, Propellers, and Articles.

(aa) For engines, propellers, and articles to be installed on aircraft with standard airworthiness certificates, each engine, propeller, and article must conform to the approved TC, must have been manufactured under an FAA-approved production system, and must be in a condition for safe operation.

(bb) For engines, propellers, and articles to be installed for aircraft with special airworthiness certificates, each engine, propeller, and article must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted civil maintenance manual and IPC specified on the TCDS, and must be in a condition for safe operation.

2 Used Dual-Use Engines, Propellers, and Articles.

(aa) For engines, propellers, and articles to be installed on aircraft with standard airworthiness certificates, an evaluation should be performed by an FAA engineer or an appropriately authorized designated engineering representative (DER). When a DER is used, the DER’s recommendations or decisions must be substantiated in writing using FAA Form 8100-9, Statement of Compliance With Airworthiness Standards, and include supporting documents. Each engine, propeller, and article must conform to the approved TC, have been manufactured under an FAA-approved production system, and be in a condition for safe operation. In addition, the following should be evaluated:

(1) Operational differences between military and civil versions (for example, possible DOD modification, alteration, or repair performed) in performance standards as listed in the TCDS (for example, thrust, shaft horsepower, revolutions per minute (RPM), and ratings), and in specifications, as listed in the TCDS and the maintenance manuals (for example, fuel type, oil, weight).

(2) Complete historical operational records. This includes extreme operational conditions such as accidents, fires, or exceeding engine operating limits.

(3) Complete historical maintenance records; for example, modifications, alterations, and repairs, and complete documentation of work performed by an FAA-approved facility that was properly rated for the work performed and that conformed to the FAA-approved data.

(4) ICA.

(5) Emission requirements as stated in the TCDS (engine only).

(6) Comparison of military time and/or cycle count for accumulated operational time and cycle versus civil (for example, “Did the military use a different method than civil operators to account for accumulated operational time and what are the expended equivalent civil cycles of the articles, taking into account their past operational history and mission profile?”).

(7) Current manufacturer’s technical data to perform tests or inspections.

(8) Written results of inspections performed (for example, maintenance record entry; FAA Form 8130-3, Authorized Release Certificate; or FAA Form 337 for approval for return to service) and a completed FAA Form 8130-9, Statement of Conformity.

(9) The application of the identifying marking requirements in accordance with §§ 45.11 and 45.13, as applicable.

(10) Engine, propeller, or article overhaul records, including overhaul in accordance with civil engine/propeller manuals.

(11) Verification that the engine, propeller, or article was produced by an FAA production approval holder (PAH).

(bb) For engines, propellers, and articles to be installed on aircraft with special airworthiness certificates, an evaluation should be performed by an FAA engineer or an appropriately authorized DER. When a DER is used, the DER’s recommendations or decisions must be substantiated in writing using FAA Form 8110-3, Statement of Compliance With Airworthiness Standards, and include supporting documents. Each engine, propeller, and article must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted maintenance manual and IPC specified on the TCDS, and be in a condition for safe operation. In addition, the following should be evaluated:

(1) Complete historical operational records. This includes extreme operational conditions such as accidents, fires, or engine exceeding operating limits.

(2) Complete historical maintenance records; for example, modifications, alterations, and repairs, and complete documentation of the work performed.

(3) ICA.

(4) Emission requirements as stated in the TCDS (engine only).

(5) Comparison of military versus civil time and/or cycle count for accumulated operational time and cycle (for example, “Did the military use a different method than civil operators to account for accumulated operational time and what are the expended equivalent civil cycles of the articles, taking into account their past operational history and mission profile?”).

(6) Current manufacturer’s technical data to perform tests or inspections.

(7) Written results of inspections performed (for example, maintenance record entry, FAA Form 8130-3, or FAA Form 337, for approval, for return to service) and a completed FAA Form 8130-9, signed by an authorized person.

(8) The application of the identifying marking requirements in accordance with §§ 45.11 and 45.13, as applicable.

(9) Engine, propeller, or article overhaul records, including overhaul in accordance with civil engine/propeller manuals.

(10) Verification that the engine, propeller, or article was produced by an FAA PAH.

(c) Approval for Installation. Persons authorized under § 43.7 may determine dual-use engines, propellers, or articles for installation if the engine, propeller, or article has successfully completed the eligibility screening and airworthiness evaluation. The installer must be able to determine that the use of the engine or propeller, and/or the installation of the article, will leave the aircraft in compliance with pertinent regulations and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

(6) Military-Unique Engines, Propellers, and Their Military-Unique Articles. Military-unique engines, propellers, and articles are FSCAPs that were specifically and uniquely designed and manufactured for the U.S. military for which there originally was no corresponding FAA-approved PAH engine, propeller, or article for civil application.

(a) Eligibility Screening. New or used military-unique engines, propellers, and articles may be eligible for installation on surplus U.S. military aircraft type certificated under § 21.25(a)(2). The eligibility determination is made based on a review of the following pertinent DOD historical records:

1 Engine, propeller, article ID (article part number and serial number and manufacturer).

2 Contract or purchase order number under which the engine, propeller, or article was manufactured.

3 Evidence of engine, propeller, and article status; for example, serviceable or unserviceable, per DD Form 1574-1 or DA Form 2410.

4 Complete historical records maintained by the military, the manufacturer, and any other prior owner(s), pertaining to inspection, modification, repair, alteration, maintenance, and operation of the engine from the time of acceptance by the military, including, but not limited to, DA Form 2408-5 and DA Form 2408-16. The maintenance records also should include the date that the work was accomplished and work authentication.

5 Current status of applicable ADs and DOD directives (for example, engineering change, technical order, maintenance work order), including the date and method of compliance; and, if the AD involves recurring action, the time and date when the next action is required.

(b) Airworthiness Determination. After determining that the engine, propeller, or article is eligible to be installed on a surplus military aircraft with special airworthiness certificates, each engine, propeller, or article must be evaluated to determine whether it is airworthy.

1 New Military-Unique Engines, Propellers, and Articles. For new military-unique engines, propellers, and their associated articles to be installed on surplus military aircraft with special airworthiness certificates, each engine, propeller, and article must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted civil maintenance manual and IPC specified on the TCDS, and must be in a condition for safe operation.

2 Used Military-Unique Engines, Propellers, and Articles. For used military-unique engines, propellers, and articles to be installed on surplus military aircraft with special airworthiness certificates, each engine, propeller, and article must be evaluated by an FAA engineer or an appropriately authorized DER. When a DER is used, the DER’s recommendations or decisions must be substantiated in writing using FAA Form 8110-3, and include supporting documents. Each engine, propeller, accessory, and associated article must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted civil maintenance manual and the IPC specified on the TCDS, and must be in a condition for safe operation.

(c) Approval for Installation. Persons authorized under § 43.7 may approve military-unique engines, propellers, or articles for installation on surplus military aircraft with special airworthiness certificates if they have successfully completed the eligibility screening and airworthiness evaluation. The installer must be able to determine that the use of the engine or propeller, and/or the installation of the article, will leave the product in compliance with the TCDS and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

Figure 2-1. Sample Aeronautical Center Form 8050-64, Assignment of

Special Registration Numbers

Figure 2-2. Sample Response Letter Regarding Identification Plates

U.S. Department of Transportation Federal Aviation Administration

March 3, 2000

Mr. William Blue 220 West Broad St. Boston, MA 26204

Dear Mr. Blue:

This is in response to your letter dated February 14, 2000, concerning disposition of the identification plate from Cessna Model 305A, Registration No. N5297G, Serial No. 305A-12345.

The aircraft will be scrapped as a result of an accident. It is requested that the aircraft registration, airworthiness certificate, identification plate, and a copy of this letter be forwarded to the address listed below.

Federal Aviation Administration Aircraft Registration Branch, AFS-750 Mike Monroney Aeronautical Center P.O. Box 25504 Oklahoma City, OK 73125-0504

Sincerely,

John J. Doe Manager Burlington Manufacturing Inspection District Office

Figure 2-3. Sample Limitations for the Operation of an Aircraft

With a Door Removed

U.S. Department of Transportation

Federal Aviation Administration

Make … Model … Serial No … Registration No …

AIRCRAFT OPERATING LIMITATIONS

The aircraft described above may be flown with not more than one cabin door removed for the purpose of (see note below), provided the aircraft is operated in accordance with the applicable sections of Title 14 of the Code of Federal Regulations and the following limitations:

Note: Show specific operations; for example, intentional parachute jumping, skydiving, etc.

1. Maximum speed not to exceed any of the following:

The approved maneuvering speed. 70 percent maximum level flight speed. 70 percent maximum structural cruising speed.

2. Aerobatic maneuvers are not permitted.

3. Maximum yaw angle 10 degrees; maximum bank angle 15 degrees.

4. A Federal Aviation Administration (FAA)-approved safety belt must be provided and worn by each occupant during takeoff and landing and at all other times when required by the pilot-in-command.

5. All occupants must wear parachutes when intentional parachute jumping and skydiving operations are conducted.

6. Smoking is not permitted.

7. When operations other than intentional parachute jumping and skydiving are conducted, a suitable guardrail or equivalent safety device must be provided for the doorway.

8. All loose articles must be tied down or stowed.

9. No baggage may be carried.

Figure 2-3. Sample Limitations for the Operation of an Aircraft

With a Door Removed (Continued)

10. Parachutists’ static lines must be kept free of pilot’s controls and control surfaces.

11. Operations are limited to visual flight rules conditions.

12. Cabin door hold-open clips installed on wing brace struts and/or under surface of wing must be removed before conducting intentional parachute jumping or skydiving operations.

13. When intentional parachute jumping, skydiving, or other specified operations are being conducted, the pilot at the controls must hold at least a private pilot certificate and appropriate rating.

14. This aircraft must not be operated in solo flight by the holder of a student pilot certificate.

15. Operation of this aircraft with a door removed for any purpose other than that for which it is certificated is prohibited.

16. The following placard must be placed on the instrument panel in full view of the pilot:

“For flight with door removed, see aircraft operating limitations dated … ”

17. A copy of these limitations must be carried in the aircraft when flight operations are conducted with the door removed.

18. These operating limitations are a part of the airworthiness certificate.

FAA Inspector … Date …

Office No …

Figure 2-4. Sample FAA Form 8100-1, Conformity Inspection Record

(Face Side Only)

Section 1. General Information

Chapter 3. Standard Airworthiness Certification

Section 1. General Information

300. General. In no case may any aircraft be operated unless there is an appropriate airworthiness certificate issued to and valid for that aircraft. This chapter provides policy and guidance material associated with airworthiness certification and issuance of FAA Form 8100-2.

a. Section 21.183(a) prescribes the basic requirements for issuance of standard airworthiness certificates for aircraft manufactured under a PC.

b. Section 21.183(b) prescribes the basic requirements for issuance of standard airworthiness certificates for aircraft manufactured under a TC.

c. Section 21.183(c) prescribes the basic requirements for issuance of the standard airworthiness certificates for an import aircraft type certificated in accordance with § 21.21 or § 21.29 and produced under the authority of another State of Manufacture. The CAA certifications must be made by issuance of an Export C of A that contains either the certification statement noted on the corresponding FAA TCDS or a certification statement that the aircraft is airworthy.

d. Section 21.183(d) prescribes the basic requirements for issuance of standard airworthiness certificates for used aircraft (aircraft with time-in-service for other than production flight testing), and for surplus aircraft of the U.S. Armed Forces.

e. Section 21.183(h) prescribes the basic requirement for issuance of a standard airworthiness certificate for new aircraft manufactured to a TC, when the applicant does not hold the TC or a licensing agreement from the TC holder. A person seeking to manufacture a new aircraft under this provision must demonstrate to the FAA that the manufacturing began before August 5, 2004. Typically, these aircraft are built from spare and surplus articles. Paragraph 315 of this order provides detailed guidance for these aircraft.

f. The FAA has full responsibility for finding that each aircraft, at the time an airworthiness certificate is issued, is airworthy. Therefore, sufficient FAA inspections of each aircraft must be conducted by the certificating ASI or authorized designee.

301. Standard Airworthiness Certificate.

a. FAA Form 8100-2 is used for all original and recurrent certification of aircraft in a standard classification only and for replacement of FAA Form 1362A still in effect. Refer to chapter 8 of this order for instructions on completing FAA Form 8100-2 (included as figure 3-1 of this order).

b. A standard airworthiness certificate remains valid as long as maintenance, preventive maintenance, and alterations are performed in accordance with parts 21, 43, and 91, and the aircraft is registered in the United States.

302. Application for Airworthiness Certificate. FAA Form 8130-6 is required whenever an airworthiness certificate is issued or amended. The application for a U.S. airworthiness certificate must be made by the registered owner or an agent who has a notarized letter of authorization (LOA) from the registered owner. The applicant must complete and sign the appropriate sections of FAA Form 8130-6 before submitting it to the FAA. Instructions for reviewing and completing FAA Form 8130-6 are found in chapter 8 of this order. Applicant instructions for completing FAA Form 8130-6 are contained in AC 21-12, Application for U.S. Airworthiness Certificate, FAA Form 8130-6.

303. Statement of Conformity.

a. FAA Form 8130-9 should be submitted to the FAA as required by §§ 21.53 and 21.130 under the following circumstances:

(1) By the applicant at the time the aircraft or articles thereof are submitted for FAA tests during the type certification program;

(2) By the applicant for each aircraft, aircraft engine, or propeller submitted for type certification; or

(3) By a TC holder or licensee manufacturing products under a TC—

(a) With the initial transfer of ownership of each product,

(b) Upon application for the original issue of an airworthiness certificate, or

(c) Upon application for an export airworthiness approval.

Note: For the purpose of this order, type certification programs include any tasks associated with the issuance of a TC or STC or the approval of FAA Form 337.

b. Review FAA Form 8130-9 for completion and ensure all of the entries are typewritten or printed legibly in permanent blue or black ink. If the certifier is also an FAA designee, the designee title will not be used. If the inspection and certification is delegated to a supplier by the applicant, a copy of the letter of delegation must be submitted to the FAA at the time of conformity. Refer to FAA Order 8110.4, Type Certification, for additional information on FAA Form 8130-9.

304. Determining Conformity.

a. When an aircraft is submitted for airworthiness certification, a determination must be made that the aircraft is in conformance with its type design. This does not imply that every article must be subjected to a conformity inspection. Conformity inspections should only be conducted when, in the FAA’s judgment, conformity to the type design for a particular article cannot be substantiated by any other means.

b. Conformity to the type design can only be established when a determination has been made that the article(s) conform to FAA-approved design data.

c. Parts catalogs or maintenance manuals may not be relied on as a sole source of information regarding the installation of parts and the validity of repairs. However, they should be used when applicable as an aid in establishing the configuration of a particular aircraft or in determining that the aircraft has been properly maintained.

d. MIDOs, MISOs, and CMOs/Certificate Management Units (CMU) having certificate management responsibility for a particular manufacturer interface with the applicable Aircraft Certification Office (ACO) to provide technical data and other pertinent information necessary to support the certification process. It is the applicant’s responsibility to provide the type design data for those products and articles for which a conformity determination must be made.

305. Basic Eligibility Requirements. Before a standard airworthiness certificate can be issued, the applicant must show the following:

a. The aircraft must be airworthy.

b. Any major alterations were accomplished in accordance with an approved STC or other FAA-approved data. If altered while in another category, the aircraft continues to meet, or has been returned to, its approved type design configuration.

c. The aircraft complies with all applicable ADs.

d. Any major repairs must conform to FAA-approved data or performed in accordance with bilateral agreement procedures

306. Certification Procedures. The procedures described herein are consistent with any other specific procedures prescribed in paragraphs dealing with individual airworthiness categories.

a. Obtain from the applicant a properly executed FAA Form 8130-6, and any other documents required for certification. The applicant must have the form completed and the appropriate sections signed before submitting it to the FAA. The application for a U.S. airworthiness certificate must be made by the registered owner or an agent who has a notarized LOA from the registered owner.

b. Contact AFS-750 to determine if an application for airworthiness certification has previously been denied. If it was denied, the reasons stated in the denial letter must be rectified before issuing an airworthiness certificate.

c. Arrange with the applicant to make available for inspection and review the aircraft, aircraft records, and any other data necessary to establish conformity to its type design.

d. Determine that the aircraft is properly registered in accordance with part 47.

e. As applicable, ensure compliance with the noise standards of § 21.93(b); § 21.183(e); part 36, Noise Standards: Aircraft Type and Airworthiness Certification; or part 91. Also ensure compliance with the fuel venting and exhaust emission requirements of part 34, Fuel Venting and Exhaust Emission Requirements for Turbine Engine Powered Airplanes, and the applicable passenger emergency exit requirements of § 21.183(f).

f. Review records and documentation to the extent necessary to establish the following:

(1) All of the required records and documentation are provided for the aircraft, that is, an up-to-date approved flight manual, a current weight and balance report, an equipment list, the maintenance records, the FAA-accepted ICA, the FAA-accepted maintenance manual(s), and any other manuals required by §§ 21.31, 21.50, 33.4, and 35.4, and by §§ 23.1529, 25.1529, 27.1529, and 29.1529. These documents must be in the English language.

(2) The aircraft is eligible by make, model, and serial number, using the TCDS, aircraft specifications, and/or applicable aircraft listing. For example, an aircraft listing may consist of aircraft model and serial numbers associated with newly manufactured aircraft that are not yet listed on the TCDS.

(3) The inspection records and technical data reflect that the aircraft conforms to the type design, all required inspections and tests have been satisfactorily completed, and the records are complete and reflect no unapproved alterations.

(4) The aircraft has been flight tested in accordance with paragraph 322 of this order, if required. If it has not been flight tested, issue the appropriate special airworthiness certificate prescribed in chapter 4 of this order. The flight test must be recorded in the aircraft records in accordance with § 91.417(a)(2)(i) as time-in-service as defined in part 1, Definitions and Abbreviations. Aircraft assembled by a person other than the manufacturer (for example, a dealer or distributor) must have been assembled and, when applicable, flight tested in accordance with the manufacturer’s FAA-approved procedures.

(5) Large airplanes, turbojet, or turbopropeller multiengine airplanes comply with the inspection program requirements of part 91, subpart E, Maintenance, Preventive Maintenance, and Alterations, or other regulations referenced therein. A supplemental structural inspection program also is required for certain large transport category airplanes. Refer to AC 91-56, Continuing Structural Integrity Program for Airplanes.

(6) The TC holder or STC holder has furnished one set of FAA-accepted ICA or one complete set of FAA-accepted maintenance manuals to the owner of the aircraft when the first standard airworthiness certificate is issued, or has procedures in place to ensure FAA-accepted ICA or maintenance manuals are provided upon delivery of the aircraft, as required by §§ 21.17(a) and (b), 21.31, and 21.50. The ICA or maintenance manuals also are required for all products with a TC or STC. If no FAA-accepted ICA or maintenance manuals are available, the ASI having certificate management responsibility over the manufacturer will contact the ACO and Aircraft Evaluation Group (AEG) to determine the status of the ICA or maintenance manuals. The ASI is responsible for ensuring the manufacturer and company

designees are made aware of the status of the ICA or maintenance manuals. No deliveries will be allowed before the ICA or maintenance manuals are approved.

Note: For additional information relative to imported products, refer to AC 21-23, Airworthiness Certification of Civil Aircraft, Engines, Propellers, and Related Products Imported to the United States.

g. Inspect the aircraft for the following:

(1) The nationality and registration marks and ID plate are displayed and marked in accordance with part 45. The information therein agrees with the application for airworthiness certification.

(2) All equipment, both required and optional, is properly installed and listed in the aircraft equipment list.

(3) Instruments and placards are correctly located, installed, and properly marked in the English language.

(4) All applicable ADs have been accomplished and appropriately recorded.

(5) The aircraft conforms to its approved U.S. TC and is in a condition for safe operation.

(6) All aircraft systems have been satisfactorily checked for proper operation.

(7) Operation of the engine(s) and propeller(s) has been checked in accordance with the aircraft manufacturer’s instructions.

h. If it is determined that the aircraft meets the requirements for the certification requested, the ASI or authorized designee will—

(1) Make an aircraft logbook entry in accordance with paragraph 801b(8)(d) of this order.

(2) Issue FAA Form 8100-2 in accordance with paragraph 802 of this order.

(3) Complete sections V and VIII of FAA Form 8130-6, as appropriate, in accordance with the instructions contained in paragraph 801b(5) and 801b(8) of this order.

(4) Examine, review, and route the certification file in accordance with paragraph 807 of this order.

i. If the aircraft does not meet the requirements for the certification requested and the airworthiness certificate is denied, the ASI must write to the applicant stating the reason(s) for denying the certificate. The ASI also will attach a copy of the denial letter to the application and forward the application to AFS-750 to be made a part of the aircraft record.

307.-308. Reserved.

Continue reading ↓ 120 of 822 passages shown