Radar Vectors
FAA Order Cancelled Issued Aug 31, 2010 AIR-200 332 pages Copy saved Nov 18, 2026

Order 8130.2G Airworthiness Certification of Aircraft and Related Products

This document is cancelled. Cancelled by 8130.2H. Check the official source before relying on it.

Official source ↗ Open PDF

Distribution: Electronic Initiated By: AIR-200

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

ORDER 8130.2G CHG 1 National Policy 7/02/2012

SUBJ: Airworthiness Certification of Aircraft and Related Products

1. Purpose. This change contains guidance related to the certification process for light-sport aircraft (LSA).

2. Who This Change Affects. This change affects all Washington headquarters branch levels of the Aircraft Certification Service, Flight Standards Service, and the Regulatory Support Division; the Aviation System Standards office; the branch level in the Aircraft Certification Service directorates and regional Flight Standards Service divisions; all aircraft certification offices; all manufacturing inspection district offices and manufacturing inspection satellite offices; all flight standards district offices; the Aircraft Certification Branch and Flight Standards Branch at the Federal Aviation Administration (FAA) Academy; all applicable representatives of the FAA; and all international field offices.

3. Explanation of Changes. This change―

a. Incorporates numerous changes to the certification processes for light-sport aircraft originating from input through the directive feedback system, field requested process clarifications, the light-sport manufacturers’ assessment report recommendations, and industry and public comments. The changes are effected throughout chapter 4, section 6, Light-Sport Aircraft Category Aircraft Airworthiness Certifications, and section 8, Experimental LSA Airworthiness Certifications.

b. Clarifies policy and details procedures to verify accuracy and completeness of airworthiness certification files, including who may apply for a certificate, procedures to review and complete FAA Form 8130-6, and local verification of completeness and accuracy of airworthiness files before submission to the Flight Standards Service, Aircraft Registration Branch.

c. Incorporates various editorial changes based on input through the directive feedback system.

Note: The use of the word “should” throughout this order refers to a recommended practice. The associated activity is not a requirement; therefore, a record of completion is not required.

ii

4. Disposition of Transmittal Paragraph. Retain this transmittal sheet until the directive is cancelled by a new directive.

PAGE CHANGE CONTROL CHART

PAGE CHANGE CONTROL CHART

Remove Pages Dated Insert Pages Dated

i thru xii 8/31/2010 i thru xii 7/02/2012 2-9 thru 2-28 8/31/2010 2-9 thru 2-28 7/02/2012 3-5 8/31/2010 3-5 8/31/2010 3-6 8/31/2010 3-6 7/02/2012 3-13 8/31/2010 3-13 8/31/2010 3-14 thru 3-15 8/31/2010 3-14 thru 3-15 7/02/2012 3-16 8/31/2010 3-16 8/31/2010 4-1 8/31/2010 4-1 7/02/2012 4-2 8/31/2010 4-2 8/31/2010 4-15 8/31/2010 4-15 8/31/2010 4-16 thru 4-132 8/31/2010 4-16 thru 4-143 7/02/2012 7-1 thru 7-2 8/31/2010 7-1 thru 7-2 7/02/2012 8-1 thru 8-5 8/31/2010 8-1 thru 8-5 7/02/2012 8-6 8/31/2010 8-6 8/31/2010 8-7 thru 8-8 8/31/2010 8-7 thru 8-8 7/02/2012 8-13 8/31/2010 8-13 8/31/2010 8-14 thru 8-21 8/31/2010 8-14 thru 8-21 7/02/2012 8-22 8/31/2010 8-22 8/31/2010 D-1 8/31/2010 D-1 8/31/2010 D-2 8/31/2010 D-2 7/02/2012

Dated

iii

Remove Pages Dated Insert Pages Dated

E-1 8/31/2010 E-1 8/31/2010 E-2 thru E-4 8/31/2010 E-2 thru E-4 7/02/2012

/s/ Terry Allen Acting Manager Production and Airworthiness Division, AIR-200

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

Nalional Policy

ORllER 8130.2G

8/31 /2010

SUBJ: Airworthiness Certification of Aircraft and Related Products

This order establishes procedures for accomplishing original and recurrent airworthiness certification of aircraft and related products and articles. The procedures contained in this order apply to Federal Aviation Administration (FAA) manufacturing aviation safety inspectors (AS I), to FAA airworthiness ASIs, and to private persons or organizations delegated authority to issue airworthiness certificate.s and related approvals.

Suggestions for improvement of this order may be submitted using FAA Form 1320·19, Directive Feedback Information, found in appendix G afthis order.

~..4 cp? ;rt?~/V'

Frank P. Paskiewicz y Manager Production and Airworthiness Division, AIR·200

Distribution: A-W (IRlFSNN) -3; A-X (CD/FS) -3; A-FFS-O (L TO); A-FAC-O (ALL); AMA-220 (50 copies); AMA-250 (10 copies); AFS-600 (3 copies); AVR-20 (ALL); AEU-100/200

Initiated By: AIR-200

ii

Table of Contents

Paragraph Page

Chapter 1. Introduction

100. Purpose of This Order … 1-1 101. Audience … 1-1 102. Where Can I Find This Order … 1-1 103. Explanation of Policy Changes … 1-1 104. Cancellation … 1-1 105. Effective Date … 1-1

Dated › Section 2. Airworthiness Certificates

Chapter 2. General Policies and Procedures

Section 1. General Information

200. Definition of the Term “Airworthy” for U.S. Type-Certificated (TC) Aircraft … 2-1 201. Representatives of the FAA Authorized To Issue Airworthiness Certificates and Related Approvals … 2-1 202. Responsibilities of FAA ASIs and Designees … 2-2 203. Possession and Display of Airworthiness Certificates … 2-3 204. Aircraft Registration … 2-3 205. Aircraft Nationality, Registration Marks, Reservation of Special Registration Numbers, and Display of Registration Marks … 2-3 206. Display of Nationality and Registration Marks on Antique and Antique Replica Aircraft … 2-5 207. Original and Replacement Aircraft Identification Plates … 2-6 208. Public Aircraft … 2-7 209. Aircraft Being Removed From a Continuous Maintenance System … 2-8 210. Operation of Civil Aircraft With a Door Open or Removed for Parachuting, Skydiving, or Other Special Operations … 2-9 211. Banner Towing … 2-10 212. Reserved … 2-10

Section 2. Airworthiness Certificates

213. General … 2-10 214. Classification and Category of Airworthiness Certificates … 2-11 215. Replacement, Exchange, or Amendment of Airworthiness Certificates … 2-11 216. Surrendered Airworthiness Certificate … 2-13 217. Aircraft Model Change … 2-14 218. Safeguarding FAA Airworthiness Certificates … 2-14 219. Recording of Conformity Inspections … 2-14

*

*

*

*

Dated › Section 2. New Aircraft

iii

Table of Contents (Continued)

Paragraph Page

220. Airworthiness Certification of Manned Free Balloons … 2-14 221. Reserved … 2-15

Section 3. Initial or Subsequent Issuance of Airworthiness Certificates (Original/Recurrent) or Related Approvals

222. General … 2-15 223. Airworthiness Certification … 2-16 224. Exceptions … 2-18 225. Recording of Conformity Inspections … 2-18 226. Eligibility and Evaluation of U.S. Military Surplus Flight Safety-Critical Aircraft Parts (Articles) (FSCAP), Engines, and Propellers … 2-18 Figure 2-1. Sample Aeronautical Center Form 8050-64, Assignment of Special Registration Numbers … 2-29 Figure 2-2. Sample Response Letter Regarding Identification Plates .. 2-30 Figure 2-3. Sample Limitations for the Operation of an Aircraft With a Door Removed … 2-31 Figure 2-4. Sample FAA Form 8100-1, Conformity Inspection Record … 2-33

Chapter 3. Standard Airworthiness Certification

Section 1. General Information

300. General … 3-1 301. Standard Airworthiness Certificate … 3-1 302. Application for Airworthiness Certificate … 3-2 303. Statement of Conformity … 3-2 304. Use of Parts Catalogs and Maintenance Manuals … 3-3 305. Basic Eligibility Requirements … 3-3 306. Certification Procedures … 3-3 307.-308. Reserved … 3-6

Section 2. New Aircraft

309. General … 3-6 310. Use of Designees … 3-6 311. Certification Procedures … 3-6 312. Aircraft Manufactured Under a TC (Without an FAA Production Approval) … 3-6 313. Aircraft Manufactured Under a Production Certificate (PC) … 3-7 314. Aircraft Manufactured Under a PC with a PC ODA … 3-7 315. Airworthiness Certification of Very Light Aircraft (VLA) … 3-7 316. Aircraft Manufactured in a Bilateral Country … 3-8

*

*

Dated › Section 3. Used Aircraft and Surplus Aircraft of the U.S. Armed Forces

iv

Table of Contents (Continued)

Paragraph Page

317. New Aircraft Manufactured Under the Provisions of 14 CFR § 21.6(b) … 3-8 318. Reserved … 3-13

Section 3. Used Aircraft and Surplus Aircraft of the U.S. Armed Forces

319. General … 3-13 320. Certification Procedures … 3-13 321. Conformity Determination … 3-14 322. Flight Testing … 3-15 323. Issuance of Standard Airworthiness Certificates Under 14 CFR § 21.183(d)—Used Aircraft and Surplus Aircraft of the U.S. Armed Forces … 3-16 324. Screening of Surplus Military Aircraft … 3-20 325. State of Conformity—Military Aircraft (FAA Form 8130-31) … 3-21 326. Issuance of Standard Airworthiness Certificates, Surplus Military Aircraft … 3-22 327. Certification Requirements (Applicant) … 3-22 328. Certification Procedures … 3-24 329. Examples of Forms … 3-24 Figure 3-1. Sample FAA Form 8100-2, Standard Airworthiness Certificate, New Aircraft … 3-25 Figure 3-2. Sample FAA Form 8100-2, Standard Airworthiness Certificate, Aircraft Assembled from Spare and Surplus Products and Articles … 3-26 Figure 3-3. Sample FAA Form 8100-2, Standard Airworthiness Certificate, VLA Under 14 CFR § 21.183(a) … 3-27 Figure 3-4. Sample FAA Form 8100-2, Standard Airworthiness Certificate, EASA CS/VLA Under 14 CFR § 21.183(c) … 3-28 Figure 3-5.

Sample FAA Form 8130-11, Checklist and Inspection Record, Aircraft Built From Spare and Surplus Articles … 3-29 Figure 3-6. Sample FAA Form 8130-9, Statement of Conformity, Aircraft Built From Spare and Surplus Articles … 3-37 Figure 3-7. Sample FAA Form 8130-31, Statement of Conformity— Military Aircraft … 3-39 Figure 3-8. Sample FAA Form 8130-10, Surplus Military Aircraft Inspection Record, No Reasonable Potential for Standard Certification … 3-42 Figure 3-9. Sample FAA Form 8130-10, Surplus Military Aircraft Inspection Record, Reasonable Potential for Standard Certification … 3-43 Figure 3-10. Sample FAA Form 8100-2, Standard Airworthiness Certificate, Surplus Military Aircraft … 3-44

*

*

Dated › Section 4. Limited Airworthiness Certification

v

Table of Contents (Continued)

Paragraph Page

Chapter 4. Special Airworthiness Certification

Section 1. General Information

4000. General … 4-1 4001. Application for Airworthiness Certificate … 4-1 4002. Certification Procedures … 4-1 4003. Special Airworthiness Certificates … 4-3 4004. Reserved … 4-4

Section 2. Restricted Airworthiness Certification

4005. General … 4-4 4006. Certification Procedures … 4-5 4007. Eligibility … 4-5 4008. Special Purpose Operations … 4-6 4009. Statement of Conformity … 4-6 4010. Operating Limitations … 4-6 4011. Agricultural Aircraft … 4-7 4012. Airworthiness Certificate … 4-7 4013. Display of Marks (Restricted) … 4-8 4014.-4015. Reserved … 4-8

Section 3. Multiple Airworthiness Certificates

4016. General … 4-8 4017. Certification Procedures … 4-8 4018. Eligibility … 4-9 4019. Special Purpose Operations … 4-9 4020. Airworthiness Certificates … 4-10 4021. Operating Limitations … 4-10 4022. Operating With Multiple Airworthiness Certificates, Standard and Restricted … 4-10 4023. Display of Marks (Restricted or Limited) … 4-11 4024.-4026. Reserved … 4-11

Section 4. Limited Airworthiness Certification

4027. General … 4-11 4028. Certification Procedures … 4-11 4029. Eligibility … 4-11 4030. Operating Limitations … 4-12 4031. Display of Marks (Limited) … 4-12

*

*

vi

Table of Contents (Continued)

Paragraph Page

4032. Aircraft Issued Limited Category TCs … 4-13 4033. Reserved … 4-13

Dated › Section 8. Experimental LSA Airworthiness Certifications

Section 5. Primary Category Aircraft Airworthiness Certifications

4034. General … 4-14 4035. Certification Procedures … 4-15 4036.-4037 Reserved … 4-15

Section 6. Light-Sport Aircraft (LSA) Category Aircraft Airworthiness Certifications

4038. General … 4-15 4039. Certification Procedures … 4-21 4040. Prototype and Production Flight Testing … 4-30 4041. Flight Test Areas … 4-32 4042. Special Flight Permit for Flight Testing LSA Category Operating Limitations … 4-32 4043. Issuance of LSA Category Aircraft Operating Limitations … 4-33 4044. LSA Statement of Compliance (SOC) … 4-35 4045.-4070. Reserved … 4-35

Section 7. General Experimental Airworthiness Certifications

4071. General … 4-35 4072. Eligibility … 4-37 4073. Demilitarization of Former Military Aircraft … 4-38 4074. Aircraft Equipped With Ejection Seats, Ballistic Parachutes, or Jettisonable Stores … 4-38 4075. Flight Test Areas … 4-39 4076. Operating Outside Flight Test Areas … 4-40 4077.-4080. Reserved … 4-41

Section 8. Experimental LSA Airworthiness Certifications

4081. General … 4-42 4082. Certification Procedures … 4-46 4083. Flight Test Areas … 4-53 4084. Issuance of Experimental Light-Sport Operating Limitations … 4-55 4085.-4095. Reserved … 4-59

*

*

vii

Table of Contents (Continued)

Paragraph Page

Section 9. Experimental Amateur-Built Airworthiness Certifications

Dated › Section 11.

4096. General … 4-60 4097. Eligibility … 4-60 4098. Determination of Major Portion … 4-61 4099. Design and Construction … 4-63 4100. FAA Evaluation of Amateur-Built Aircraft Kits … 4-66 4101. Advising Applicants … 4-67 4102. Certification Procedures … 4-69 4103. Flight Test Areas … 4-74 4104. Issuance of Experimental Amateur-Built Operating Limitations … 4-75 4105.-4106. Reserved … 4-80

Section 10. Certification and Operation of Aircraft under the Experimental Purpose(s) of Exhibition and Air Racing

4107. General … 4-80 4108. Former Military Aircraft … 4-81 4109. Brokering … 4-82 4110. Groups of Aircraft … 4-82 4111. Special Initial Certification Requirements … 4-86 4112. Certification Procedures … 4-87 4113. Issuance of Experimental Exhibition and Air Racing Operating Limitations … 4-88 Table 4-1. Operating Limitations to be Issued … 4-89 4114.-4124. Reserved … 4-96

Section 11. Certification and Operation of Aircraft under the Experimental Purpose(s) of Research and Development, Showing Compliance with Regulations, Crew Training, Market Surveys, and Operating Kit-Built Aircraft

4125. General … 4-96 4126. Special Certification Requirements … 4-98 4127. PC Holder and Modifier Experimental Operating Procedure … 4-98 4128. Issuance of Experimental Research and Development, Showing Compliance with Regulations, Crew Training, Market Surveys, and Operating Kit-Built Aircraft Operating Limitations … 4-99 4129.-4135. Reserved … 4-105

*

*

Dated › Section 13. Special Flight Permits

viii

Table of Contents (Continued)

Paragraph Page

Section 12. Provisional Airworthiness Certification

4136. General … 4-105 4137. Eligibility … 4-105 4138. Special Purpose Operations … 4-105 4139. Statement of Conformity … 4-106 4140. Certification Procedures … 4-106 4141. Special Airworthiness Certificate, FAA Form 8130-7 … 4-106 4142. Operating Limitations … 4-106 4143.-4160. Reserved … 4-106

Section 13. Special Flight Permits

4161. General … 4-106 4162. Purposes … 4-108 4163. Application and Issuance (General) … 4-109 4164. Aircraft Inspections … 4-109 4165. Special Operating Limitations … 4-110 4166. Special Flight Permit for Operation of Overweight Aircraft … 4-111 4167. Special Flight Permit for Production Flight Testing … 4-114 4168. Special Flight Permit for Conducting Customer Demonstration Flights … 4-115 4169. Special Flight Permit for Certain Large Aircraft for which 14 CFR Part 125, Certification and Operations: Airplanes Having a Seating Capacity of 20 or More Passengers or a Maximum Payload Capacity of 6,000 Pounds or More, is not Applicable … 4-116 Figure 4-1. Sample FAA Form 8130-7, Special Airworthiness Certificate … 4-119 Figure 4-2. Sample FAA Form 8130-7, Special Airworthiness Certificate for Restricted Category Aircraft Certificated Under 14 CFR § 21.25(b)(7) … 4-120 Figure 4-3. Sample FAA Form 8130-7, Special Airworthiness Certificate for Primary Category Aircraft Certificated Under 14 CFR § 21.184(a) … 4-121 Figure 4-4. Sample FAA Form 8130-7, Special Airworthiness Certificate for Primary Category Aircraft Certificated Under 14 CFR § 21.184(b) … 4-122 Figure 4-5. Sample FAA Form 8130-7, Special Airworthiness Certificate for Primary Category Aircraft Certificated Under 14 CFR § 21.184(c) … 4-123 Figure 4-6. Sample Operating Limitations for Primary Category Aircraft Certificated Under 14 CFR § 21.184(c) … 4-124

*

*

ix

Table of Contents (Continued)

Paragraph Page

Figure 4-7. Sample FAA Form 8130-7, Special Airworthiness Certificate for Experimental to Show Compliance with the CFR … 4-125 Figure 4-8. Sample Operating Limitations for Experimental Kit-Built Aircraft … 4-126 Figure 4-9. Sample Program Letter, Research and Development/Showing Compliance Applicant Program Letter Special Airworthiness Certificate … 4-127 Figure 4-10. Sample FAA Form 8130-12, Eligibility Statement, Amateur-Built Aircraft … 4-128 Figure 4-11. Sample FAA Form 8000-38, Fabrication/Assembly Operation Checklist … 4-129 Figure 4-12. Sample FAA Form 8130-7, Unlimited … 4-134 Figure 4-13. Sample FAA Form 8130-7, Special Flight Permit … 4-135 Figure 4-14. Sample FAA Form 337, Major Repair and Alteration ... 4-136 Figure 4-15. Sample FAA Form 8130-7, Special Flight Permit LSA … 4-137 Figure 4-16. Sample Special Flight Permit Operating Limitations for LSA Category Production Flight Testing … 4-138 Figure 4-17. Sample FAA Form 8130-7, Special Airworthiness Certificate for LSA Category Aircraft Certificated Under 14 CFR § 21.190 … 4-139 Figure 4-18. Sample FAA Form 8130-7, Special Airworthiness Certificate for Experimental LSA Certificated Under 14 CFR § 21.191 … 4-140 Figure 4-19. Sample FAA Form 8130-15, Light-Sport Aircraft Statement of Compliance … 4-141 Figure 4-20. Sample FAA Form 8130-15, Light-Sport Kit-Built Aircraft Statement of Compliance … 4-142 Figure 4-21. Use of Prior Policy … 4-143

Dated › Section 2. Export Approvals

Chapter 5. Export Approval Procedures

Section 1. General Information

500. General … 5-1 501.-504. Reserved … 5-2

Section 2. Export Approvals

505. 14 CFR § 21.323, Eligibility … 5-2 506. 14 CFR § 21.325, Export Airworthiness Approvals … 5-2 507. 14 CFR § 21.327, Application … 5-3 508. Issuance of FAA Form 8130-4, Export Certificate of Airworthiness, for Aircraft (14 CFR § 21.329) … 5-3

*

*

Dated › Section 3. Aircraft Engines, Propellers, and Articles

x

Table of Contents (Continued)

Paragraph Page

509. Issuance of FAA Form 8130-3, Airworthiness Approval Tag, for Engines, Propellers, and Articles (14 CFR § 21.331) … 5-4 510. Responsibilities of Exporters (14 CFR § 21.335) … 5-4 511. Determination for “New” and “Used” Products or Articles … 5-5 512. Preparation of Export C of A … 5-5 513. Approval of Modifications … 5-8 514. Export Certificate Number Assignment Card … 5-8 515. Routing and Processing of Export Files … 5-8 516. Issuance of Export C of A for Aircraft TC’d in Multiple Categories … 5-9 517. Issuance of Export C of A for Restricted Category Aircraft … 5-9 518. Controversial Information … 5-9 Figure 5-1. Sample FAA Form 8130-4, Export Certificate of Airworthiness … 5-10 Figure 5-2. Sample FAA Form 8130-1, Application for Export Airworthiness Approval … 5-11 Figure 5-3. Aeronautical Center Form 8050-72, Export Certificate Number Assignment Card … 5-13

Chapter 6. Import Procedures

Section 1. General Information

600. General … 6-1 601.-602. Reserved … 6-2

Section 2. Import Aircraft

603. Requirements for U.S. Airworthiness Certification … 6-2 604. Application … 6-3 605. Airworthiness Determination … 6-3 606. Airworthiness Certification of Aircraft With Mandatory Continuing Airworthiness Information … 6-5 607. Certification Procedures … 6-6 608.-609. Reserved … 6-6

Section 3. Aircraft Engines, Propellers, and Articles

610. Airworthiness Determination … 6-7 611. Identification and Marking … 6-8 612. Return to Service … 6-8 613. Special Maintenance Records Consideration … 6-9

*

*

xi

Table of Contents (Continued)

Paragraph Page

Chapter 7. Special Flight Authorizations (SFA) for Non-U.S.-Registered Civil Aircraft

700. General … 7-1 701. Eligibility … 7-1 702. Blanket SFAs … 7-2 703. Application … 7-2 704. Issuance … 7-4 705. Duration … 7-5 706. Operating Limitations … 7-5 707. SFA for Operation of Canadian-Registered Amateur-Built Aircraft in the United States … 7-9 Figure 7-1. Sample SFA for the Flight of an Aircraft to a Place Where Repairs or Alterations are to be Made … 7-11 Figure 7-2. Sample SFA for the Flight of an Aircraft to a New State of Registry (This Format Is Generally Applicable to a Single Aircraft Authorization for Ferry Flights) … 7-13 Figure 7-3. Sample SFA for the Purpose of Flight Testing … 7-15 Figure 7-4. Sample Blanket SFA for Customer Crew Training … 7-17 Figure 7-5. Sample SFA for Export Delivery … 7-19 Figure 7-6. Sample Blanket SFA for Delivering Aircraft for the Purpose of Export Delivery … 7-21 Figure 7-7. Sample SFA for the Purpose of Demonstration … 7-23 Figure 7-8. Sample SFA for Canadian-Registered Amateur-Built Aircraft (Example: Authorization for the Purpose of Attending an Airshow) … 7-25 Figure 7-9. Sample Blanket SFA for Glider Meet … 7-27

Chapter 8. Processing Forms, Reports, and Certification Files

800. General … 8-1 801. Review and Completion of FAA Form 8130-6 … 8-1 802. Completion of FAA Form 8100-2 … 8-11 803. Completion of FAA Form 8130-7 … 8-12 804. Instructions for Reviewing a Completed FAA Form 8130-15, Light-Sport Statement of Compliance … 8-15 805. Completion of FAA Form 8130-4 … 8-17 806. Completion of FAA Form 8130-1 … 8-18 807. Examination, Review, and Routing of Certification Files … 8-10 Figure 8-1. Sample FAA Form 8130-6, Application for U.S. Airworthiness Certification … 8-23

*

*

xii

Table of Contents (Continued)

Paragraph Page

Appendix A. Issuance of U.S. Standard Airworthiness Certificates for New Aircraft Manufactured Outside the United States

1. Purpose … A-1 2. Applicability … A-1 3. Procedure … A-1 4. Administrative Requirements … A-8

Appendix B. Acceptance of an Export C of A for Used Aircraft Under a Bilateral Agreement

1. Purpose … B-1 2. Responsibilities of ASIs and Designees … B-1 3. One Hundred-Hour Inspection Requirement … B-1 4. Special Bilateral Provisions … B-2 Table B-1. Bilateral Agreements that Provide for Acceptance of an Export C of A for Used Aircraft … B-4

Appendix C. Forms Listing and Availability … C-1

Appendix D. Acronyms … D-1

Appendix E. Definitions … E-1

Appendix F. Administrative Information

1. Distribution … F-1 2. Authority to Change This Order … F-1 3. Deviations … F-1 4. Suggestions for Improvements … F-1 5. Records Management … F-1

Appendix G. Directive Feedback Information … G-1

*

*

Chapter 1. Introduction

Chapter 1. Introduction

100. Purpose of This Order. This order establishes procedures for accomplishing original and recurrent airworthiness certification of aircraft and related products and articles.

101. Audience. FAA manufacturing ASIs, FAA airworthiness ASIs, and private persons or organizations delegated authority to issue airworthiness certificates and related approvals.

102. Where Can I Find This Order. You can find this order on the MYFAA Employee website or the FAA public website.

103. Explanation of Policy Changes. This revision—

a. Incorporates the required amendments (numbers 1-64, 21-92, 43-43, and 45-26) to Title 14 of the Code of Federal Regulations (14 CFR) parts 1, 21, 43, and 45 released October 16, 2009.

b. Incorporates changes to chapter 4, section 10, Certification and Operation of Aircraft Under the Experimental Purpose(s) of Exhibition and Air Racing.

c. Incorporates numerous changes originating from input through the directive feedback system. Areas affected are throughout this order and include light-sport aircraft (LSA).

d. Incorporates changes to several FAA forms including FAA Forms: 8100-2, Standard Airworthiness Certificate; 8130-1 Application for Export Certificate of Airworthiness; 8130-4, Export Certificate of Airworthiness; 8130-7, Special Airworthiness Certificate; 8130-9, Statement of Conformity; 8130-10, Surplus Military Aircraft Inspection Record; 8130-11, Checklist and Inspection Record; and 8130-31, Statement of Conformity-Military Aircraft, which supersedes 8130-2.

e. Deletes examples for an applicant to complete FAA Form 8130-6, Application for U.S. Airworthiness Certificate. The applicant’s primary reference for this form is Advisory Circular (AC) 21-12, Application for U.S. Airworthiness Certificate, FAA Form 8130-6. Greater detail is added to the review instructions for FAA Form 8130-6 in chapter 8 of this order.

f. Updates the order format in accordance with the guidelines of FAA Order 1320.1E, FAA Directives Management.

104. Cancellation. FAA Order 8130.2F, Airworthiness Certification of Aircraft and Related Products, dated November 5, 2004, is cancelled upon the effective date of this order.

105. Effective Date. This order is effective April 16, 2011.

Chapter 2. General Policies and Procedures

Section 1. General Information

Section 1. General Information

200. Definition Of The Term “Airworthy” for U.S. Type-Certificated (TC) Aircraft. Although the term “airworthy” is defined in 14 CFR § 3.5(a), a clear understanding of its meaning is essential for use in the FAA’s airworthiness certification program. Below is a summary of the conditions necessary for the issuance of an airworthiness certificate. A review of case law relating to airworthiness reveals two conditions that must be met for an aircraft to be considered “airworthy.” Title 49, United States Code (49 U.S.C.) § 44704(c) and 14 CFR § 21.183(a), (b), and (c) state that the following two conditions necessary for issuance of an airworthiness certificate:

a. The aircraft must conform to its type design. Conformity to the type design is considered attained when the aircraft configuration and the engine, propeller, and articles installed are consistent with the drawings, specifications, and other data that are part of the TC. This includes any supplemental type certificate (STC) and repairs and alterations incorporated into the aircraft.

b. The aircraft must be in a condition for safe operation. This refers to the condition of the aircraft relative to wear and deterioration, for example, skin corrosion, window delamination/crazing, fluid leaks, and tire wear.

Note: If one or both of these conditions are not met, the aircraft would not be considered airworthy. Aircraft that have not been issued a TC must meet the requirements of paragraph 200b of this order.

201. Representatives of the FAA Authorized to Issue Airworthiness Certificates And Related Approvals.

a. Consistent with applicable Aircraft Certification Service policies and instructions, an FAA manufacturing or airworthiness ASI is authorized to issue airworthiness certificates and related approvals covered in this order.

b. The FAA is authorized under 14 CFR part 183, Representatives of the Administrator, to designate private persons or organizations to act as representatives of the Administrator to issue airworthiness certificates and related approvals. A designated manufacturing inspection representative (DMIR) or designated airworthiness representative (DAR) may issue standard and special airworthiness certificates, airworthiness approvals, and export approvals, and may perform certain other examinations, inspections, and testing services relative to certification functions in the areas of manufacturing and maintenance. ASI certification functions will be delegated to the fullest extent practical, but not to the extent an advisor’s technical skills are jeopardized. The designee’s Certificate of Authority must specify the type and limitation of authority granted.

Note: The authority of a DMIR must be specifically linked to a production approval holder (PAH) or a PAH’s approved supplier.

c. The FAA is authorized under 14 CFR part 183, subpart D, to delegate specific functions to organizations on behalf of the FAA, related to engineering, manufacturing, operations, airworthiness, or maintenance for the purpose of issuing airworthiness certificates and related approvals. An organization designation authorization (ODA) may be approved to issue airworthiness certificates, airworthiness approvals, conformity certifications, and export approvals. See FAA Order 8100.15, Organization Designation Authorization Procedures, for further information on ODA.

d. The use of electronic signatures on airworthiness certificates, including Export Certificates of Airworthiness, is not permitted.

202. Responsibilities of FAA ASIs and Designees.

a. The procedures in this order cover original airworthiness certification for which FAA manufacturing ASIs are primarily responsible, and recurrent airworthiness certification for which FAA airworthiness ASIs are primarily responsible. FAA manufacturing and airworthiness ASIs may assist each other by mutual agreement.

b. The FAA designees, within the limits of their authority, are authorized to issue original or recurrent airworthiness certificates and related approvals. They are responsible for determining that the products or articles submitted to them conform to the approved type design, are in a condition for safe operation, and meet any other specified requirements. They also are responsible for the completeness, accuracy, and processing of all official documents and paperwork as provided for in this order. All actions taken by the designees on behalf of the FAA are subject to the monitoring, review, and approval of the supervising ASIs.

c. ASIs are responsible for training and supervising designees assigned to them regarding airworthiness certification procedures and all related documentation. The supervising ASI should also ensure that designees have been provided (or have access to) the appropriate regulations, instructions, and forms necessary for the performance of their designated duties.

d. ASIs will supervise and maintain surveillance over the certification activities accomplished by designees to ensure that all certifications and approvals comply with the applicable rules, policies, and procedures.

Note: In this order, the term “FAA” or “ASI,” as it relates to airworthiness certification activity, refers to the FAA airworthiness inspector (that is, manufacturing and flight standards) and that person’s authorized designee. Designees will perform only authorized functions on behalf of their managing office and FAA advisor.

e. Before a designee can issue a special airworthiness certificate or a special flight permit, they must obtain in writing from the geographically responsible Manufacturing Inspection District Office (MIDO), Flight Standards District Office (FSDO) or Certificate Management Office (CMO) that the limitations are acceptable, including any additional limitations and areas of operation the FAA considers necessary for safety.

N1 through N99999, all symbols are numeric.

203. Possession and Display of Airworthiness Certificates. Any airworthiness certificate issued to a U.S.-registered civil aircraft must be displayed at the cabin or cockpit entrance so that the certificate is legible to passengers or flightcrew members (14 CFR part 91, General Operating and Flight Rules, § 91.203(b)).

204. Aircraft Registration.

a. Registration. The procedures for aircraft registration and issuance of registration numbers are contained in 14 CFR part 47, Aircraft Registration. The registration of aircraft is not a function of airworthiness certification; however, U.S. registration is a prerequisite for issuance of an airworthiness certificate. The FAA must ensure that an aircraft presented for airworthiness certification is properly registered (49 U.S.C. § 44704(c) and 14 CFR § 21.173).

b. Proof of Ownership. The applicant for registration of an aircraft must submit proof of ownership to the Flight Standards Service, Aircraft Registration Branch (AFS-750) that meets the requirements prescribed in 14 CFR part 47. The Aeronautical Center Form 8050-2, Aircraft Bill of Sale, or its equivalent, may be used as proof of ownership. If the applicant did not purchase the aircraft from the last registered owner, the applicant must submit a complete chain of ownership from the last registered owner to the applicant. The purchaser under a contract of conditional sale is considered the owner for the purpose of registration. The contract of conditional sale may be submitted as proof of ownership in lieu of a bill of sale.

c. Aircraft Operation Outside the U.S. Pending U.S. Registration. For aircraft operations to or from the United States, including operations conducted wholly outside the United States, a current airworthiness certificate and Aeronautical Center Form 8050-3, Certificate of Aircraft Registration, must be carried in the aircraft. Pending receipt of Aeronautical Center Form 8050-3, AFS-750 will, upon request, transmit a telex/fax confirmation of registration on Form AFS-750-FAX-4 to the party whose name appears on the application as owner or authorized agent. The telex/fax may be used as a temporary Certificate of Aircraft Registration pending receipt of the original certificate.

205. Aircraft Nationality, Registration Marks, Reservation of Special Registration Numbers, and Display of Registration Marks.

a. Registration Numbers. All U.S. civil aircraft registration numbers are prefixed by an “N.” The registration number, apart from the “N” prefix, is made up of one to five symbols, the last two of which may be alphabetical. This alphabetical suffix must be preceded by at least one numerical symbol. The lowest possible number is N1. A zero never precedes the first number. For example:

N1 through N99999, all symbols are numeric. N1A through N9999Z, single alphabetical suffix. N1AA through N999ZZ, double alphabetical suffix.

Note: To avoid confusion with the numbers zero and one, the letters “O” and “I” are never used as alphabetical suffixes.

b. Reservation of Registration Numbers.

(1) A person may reserve a registration number of his or her choice, if available, for 1 year by sending a written request and the appropriate fee for each number to be reserved to the following address:

FAA Aircraft Registration Branch, AFS-750

Mike Monroney Aeronautical Center

P.O. Box 25504 Oklahoma City, OK 73125-0504

(2) The applicant should list five numbers in case the first choice is not available. Reservations may be renewed from year to year by paying the appropriate fee before the end of the renewal period. If the renewal payment is not received before the end of the 1-year period, reservation of the special registration number will expire.

Note: Once AFS-750 has been notified that the numbers have been permanently affixed to the aircraft and the airworthiness certificate has been issued, no subsequent fees apply.

c. Special Registration Numbers.

(1) Aircraft owners must apply for a special registration number in writing to AFS-750 and describe the aircraft. Permission to place the special number on the aircraft will be given on Aeronautical Center Form 8050-64, Assignment of Special Registration Numbers. The owner must complete, sign, and return the original form to AFS-750 within 5 days after the special registration number is affixed to the aircraft. The duplicate of Aeronautical Center Form 8050-64 and the present airworthiness certificate must be presented to the FAA representative, who will issue a replacement airworthiness certificate showing the new registration number. The old Certificate of Aircraft Registration and the duplicate Aeronautical Center Form 8050-64 must be carried in the aircraft until the new Certificate of Aircraft Registration is received (see 14 CFR § 47.15(f) and figure 2-1 of this order).

(2) Any changes in the current assignment of nationality and registration numbers will be processed as a request for assignment of special registration numbers.

d. Size of Registration Numbers.

(1) Nationality and registration marks displayed on all aircraft, with exception of aircraft covered in 14 CFR part 45, Identification and Registration Marking, § 45.29(b)(1)(iii) and (b)(2), must be at least 12 inches high in accordance with 14 CFR § 45.29. However, certain aircraft may display smaller registration marks as identified in 14 CFR § 45.29(b)(1)(i) and (b)(3) until the aircraft are repainted, restored, or changed. Once these aircraft are repainted or the marks are repainted, restored, or changed, 12-inch-high registration numbers must be displayed.

(2) FAA inspectors should be alert for newly repainted aircraft registration marks and ensure the marking is consistent with 14 CFR § 45.29. An enforcement action should be initiated against the aircraft owner/operator whenever an FAA inspector finds that an aircraft has not been marked with 12-inch-high registration numbers in accordance with 14 CFR § 45.29(b)(1)(i) or (b)(3).

(3) Nationality and registration marks of at least 3 inches high may be displayed on an aircraft issued an experimental certificate under 14 CFR § 21.191(d), (g), or (i) to operate as an exhibition aircraft or an amateur-built aircraft, or when the aircraft maximum cruising speed does not exceed 180 knots calibrated airspeed. Marks of at least 3 inches high also may be displayed on airships, spherical balloons, nonspherical balloons, powered parachutes, and weight-shift-control aircraft in accordance with 14 CFR § 45.29.

(4) When marks include only the Roman capital letter “N” and the registration number is displayed on limited, restricted, light-sport, experimental, or provisionally certificated aircraft, the operator must also display on that aircraft near each entrance to the cabin, cockpit, or pilot station, in letters not less than 2 inches nor more than 6 inches high the words “limited,” “restricted,” “light-sport,” “experimental,” or “provisional,” as applicable per 14 CFR § 45.23.

(5) Powered parachute and weight-shift-control aircraft must display the marks required by 14 CFR § 45.23. The marks must be displayed horizontally and in two diametrically opposite positions on any fuselage structural member.

206. Display of Nationality and Registration Marks on Antique and Antique Replica Aircraft.

a. 14 CFR § 45.22(b)(1)(ii) provides, in pertinent part, that small U.S-registered aircraft at least 30 years old, or aircraft that have been issued an experimental certificate for the purpose of exhibition or operating an amateur-built aircraft and that have the same exterior configuration as a 30-year-old aircraft, may display marks consisting of the Roman capital letter “N” followed by the U.S. registration number or the symbol appropriate to the airworthiness certificate of the aircraft (for example, “C,” standard; “R,” restricted; “L,” limited; or “X,” experimental) followed by the U.S. registration number. The symbol used must be appropriate for the airworthiness certificate of the aircraft being certificated, NOT the aircraft being replicated.

Example 1. A Great Lakes 2T-1A aircraft manufactured in 1929 is registered in the United States and has been issued nationality and registration mark N1234. The aircraft has been issued a standard airworthiness certificate. The owner/operator may display the mark NC1234 if so desired.

Example 2. An aircraft that has the same exterior configuration as the Great Lakes 2T-1A is registered in the United States and has been issued nationality and registration mark N5678. An experimental airworthiness certificate has been issued under 14 CFR § 21.191(d) or § 21.191(g). The owner/operator may display the mark NX5678 if so desired.

b. When aircraft are marked as described in 14 CFR § 45.22(b)(1)(ii), the airworthiness and registration certificates will not include the inserted symbol. In example 1 above, the aircraft could be marked NC1234, but the registration and airworthiness certificates would reflect only the N1234.

c. When making a query of the FAA Civil Aviation Registry (FAA Aircraft Registry) computer database, the inserted symbol must be omitted in order to obtain accurate information concerning the aircraft.

d. In addition, 14 CFR § 45.23(b) provides that when the appropriate symbol is used with the nationality and registration marks in accordance with 14 CFR § 45.22(b)(1)(ii), the word “limited,” “restricted,” or “experimental” is not required to be displayed on the aircraft.

207. Original and Replacement Aircraft Identification Plates.

a. Original Data Plates. Each aircraft presented for airworthiness certification must meet the requirements of 14 CFR § 21.182. Each aircraft, aircraft engine, propeller, propeller blade, and propeller hub manufactured under a TC or PC, or an aircraft to be certificated as an amateur-built, primary kit-built, or LSA, must be identified with the information specified in 14 CFR § 45.13. Manned free balloons are required to comply with 14 CFR § 45.11(d).

b. Replacement Data Plates.

(1) When FAA personnel receive inquiries regarding replacement, removal, or destruction of identification (ID) plates, the sample letter in figure 2-2 of this order may be used as a guide for responding.

(2) When a new ID plate is required, the owner or the owner’s authorized representative will contact their local FAA office. The FAA determines whether the request is valid and provides a letter to the applicant with the FAA’s finding. If the FAA determines that the request is valid, the applicant includes the FAA letter with his or her request for the replacement data plate from the appropriate manufacturer.

(3) Upon notification by the applicant, which must include the FAA’s letter, the product manufacturer may then issue the replacement ID plate.

(4) The old ID plate, when available, must be voluntarily surrendered by the owner with a written statement to the FAA office who authorized the replacement. The FAA office must make a copy of the plate and then physically destroy it. The FAA office must then submit a letter to AFS-750 stating that the surrendered plate has been destroyed. AFS-750 will include the letter in the permanent aircraft records file.

c. Removal of Data Plates. 14 CFR § 45.13 permits persons performing maintenance operations under 14 CFR part 43, Maintenance, Preventive Maintenance, Rebuilding, and Alteration, to remove an aircraft data plate. The removal must be done in accordance with the methods, techniques, and practices acceptable to the FAA. The ID plate removed may be reinstalled only on the product from which it was removed.

d. Misuse of Data Plates.

(1) ASIs should be on alert for any indication of ID plate misuse or suspicious activity, such as the building of a complete aircraft by a person performing work under 14 CFR part 43. Installation of an ID plate by a person performing work under 14 CFR part 43, where the ID plate has been purchased or salvaged from another aircraft, is not approved unless written approval is obtained from the FAA.

(2) Before issuing an airworthiness certificate for an aircraft that appears to be a repair or restoration of an aircraft that previously has been destroyed or demolished, the ASI should seek the assistance of the manager of AFS-750. That office can assist the ASI in determining whether the serial number of the aircraft on which certification is sought is the serial number of an aircraft previously classified as destroyed or demolished by the FAA or the National Transportation Safety Board (NTSB). If the ASI determines that the ID plate comes from a previously destroyed or demolished aircraft, the ASI must initiate an investigation to determine whether a violation of 14 CFR § 45.13(c) or (e) has occurred before the airworthiness certificate may be issued. If a violation of 14 CFR § 45.13(c) or (e) is found, the ASI must deny the airworthiness certificate and initiate an enforcement action.

Note: When the ID plate is surrendered, the ID plate is no longer considered personal property.

e. New Data Plates. The appropriate local MIDO, Manufacturing Inspection Satellite Office (MISO), or FSDO may authorize a builder of an aircraft authorized to be assembled from spare and/or surplus articles in accordance with AC 21-13, Standard Airworthiness Certification of Surplus Military Aircraft and Aircraft Built From Spare Parts, to make a new data plate for that aircraft upon a satisfactory showing that the aircraft conforms to its type design and is in a condition for safe operation. However, ensure aircraft is eligible for an airworthiness certificate as built from spare and/or surplus articles in accordance with 14 CFR § 21.6, § 21.183, and paragraph 317 of this order before authorizing the builder to make a data plate. The data plate will be made in accordance with 14 CFR part 45 and affixed to the aircraft prior to the issuance of any airworthiness certificate.

208. Public Aircraft.

a. Public aircraft are defined in 49 U.S.C. § 40102(a)(41).

b. “Public Aircraft” is not a status that is granted by the FAA. There is no requirement to make a declaration in writing of this status, nor is there any responsibility to carry any proof of this status. The burden of proof is on the operator to establish to the FAA’s satisfaction that an aircraft is a public aircraft if its status is questioned.

c. A U.S.-registered public aircraft operating within the territorial limits of the United States is not required to have an airworthiness certificate. However, any U.S.-registered public aircraft engaged in international air navigation is required to have a valid C of A, in accordance with the International Civil Aviation Organization (ICAO) agreements.

d. Safety is enhanced through the operation of aircraft certificated according to 14 CFR part 21, and the FAA encourages those who operate public aircraft to obtain the appropriate airworthiness certification, if possible. An application for an airworthiness certificate for a public aircraft will be processed in accordance with the applicable procedures in this order. The airworthiness certificate, when issued, is effective only if all terms and conditions of the certificate are complied with. If 14 CFR parts 43, 45, and 91 are NOT complied with, FAA Form 8100-2, Standard Airworthiness Certificate, must be surrendered.

e. Public aircraft must be registered in accordance with 14 CFR part 47 and must display nationality and registration marks in accordance with 14 CFR part 45. Any deviations from these requirements must be processed in accordance with the procedures in 14 CFR part 11, General Rulemaking, applicable to petitions for exemptions.

f. Aircraft operated by the FAA will be certificated in accordance with 14 CFR part 21, except for those aircraft authorized by the Director, Office of Aviation System Standards, or by the Director’s designee, to be operated as public aircraft. Certificated aircraft must display an appropriate airworthiness certificate.

g. Non-certificated FAA aircraft will display a public aircraft document in lieu of the airworthiness certificate. All requests for the public aircraft document will be processed through the Director, Aviation Systems Standards, Oklahoma City, Oklahoma (AVN-100). The letter of request must contain, at a minimum, the—

(1) Nationality and registration marks,

(2) Manufacturer and model,

(3) Aircraft serial number,

(4) Location (base of operation/airport) of the aircraft, and

(5) Registered owner and operator of the aircraft.

h. The signed public aircraft document will be displayed in the aircraft at all times in lieu of the airworthiness certificate. For procedures applicable to public aircraft operated by the FAA, see TI-4100.24, Aviation System Standards General Maintenance Manual.

209. Aircraft Being Removed from a Continuous Maintenance System.

a. No change in the airworthiness certificate is required if the aircraft has a current airworthiness certificate, FAA Form 8100-2.

b. Operators of aircraft previously operated under 14 CFR part 121, Operating Requirements: Domestic, Flag, and Supplemental Operations, or 14 CFR part 91, subpart D, Special Flight Operations, and intending to operate them under 14 CFR part 91, must select, identify, establish, and use an inspection program as prescribed in 14 CFR § 91.409(e), (f), (g), and (h).

c. It also is important for the operator to know the current status of the aircraft relative to applicable requirements; for example, (1) weight and balance data, (2) flight manual appropriate to the operation, and (3) compliance with airworthiness directives (AD). Some carriers have exemptions or adjusted AD compliance times.

210. Operation of Civil Aircraft with a Door Open or Removed for Parachuting, Skydiving, or Other Special Operations.

a. AC 105-2, Sport Parachute Jumping, appendix 2, identifies aircraft that the FAA has determined can safely be flown with one door open or removed if operated in accordance with specified operating limitations.

b. Owners or operators using aircraft listed in AC 105-2, appendix 2, and who are interested in obtaining authorization with operating limitations for operation of an aircraft with a door open or removed for parachuting or other special operations, must forward a written request to the FSDO having jurisdiction over the area in which the operations are to be conducted. The request must contain the following information:

(1) Name and address of the registered aircraft owner;

(2) Make, model, serial, and registration number of the aircraft;

(3) Location where aircraft normally is based; and

(4) Reason for the aircraft to be operated with a door removed.

c. Aircraft may be approved to operate with a door open or removed by type certificate, amended type certificate, supplemental type certificate, authorization in the aircraft’s flight manual, or field approval.

(1) Aircraft approved by type certificate, amended type certificate, supplemental type certificate, or approved flight manual authorization do not require any additional limitations.

(2) Aircraft approved to operate by issuance of FAA Form 337, Major Repair & Alteration, must have operating limitations issued. Sample operating limitations are outlined in figure 2-3 of this order. Field approval guidance is in FAA Order 8900.1, Flight Standards Information Management System (FSIMS).

d. Sample operating limitations are outlined in figure 2-3 of this order and must be issued by ASIs for any aircraft without a TC or STC. The ASI must note on the operating limitations the aircraft make, model, registration and serial number, type of operation authorized, date of issuance, ASI’s name, and district office number. On an aircraft that requires removal or opening of a particular door, the ASI must specify in the limitations which door may be removed or opened.

Note: A copy of the limitations must be forwarded to AFS-750.

*

*

*

*

Section 2. Airworthiness Certificates

e. Removal or installation of a cabin door for the specified aircraft is considered maintenance and as such must be accomplished by persons authorized under 14 CFR § 43.3.

f. If operations of rotorcraft with the doors opened or removed obstructs the nationality and registration marks from view, the operator must notify the appropriate managing office in writing detailing the nature of the proposed operation and the proposed dates of operation with doors removed. The managing office will then instruct the operator to affix temporary nationality and registration marks on an authorized surface required by 14 CFR § 45.27(a). The size of the marks must comply with 14 CFR § 45.29(b) unless no authorized surface is large enough for display of marks meeting the size requirements of this section. The rotorcraft would then be marked on the largest authorized surface with marks as large as practicable, as allowed by 14 CFR § 45.29(f). Any remnants of the permanent nationality and registration marks must be obliterated so as not to confuse identification of the rotorcraft with temporary markings. The temporary markings must be able to endure flight operations in various weather conditions. Flight operations must be authorized in writing by the managing office for a specified time and purpose. The managing office will verify that the temporary markings comply with 14 CFR part 45 and that the rotorcraft is returned to its permanent marking scheme.

g. Under appendix A to 14 CFR part 43, paragraph (c)(15), a pilot may be authorized to remove or reinstall passenger seats if the pilot is specifically listed by name in the operating limitations for the aircraft. The issuing ASI may require the pilot to demonstrate his or her ability in this preventive maintenance function.

h. Removal or installation of control sticks and wheels must be performed in accordance with the applicable sections of 14 CFR part 43.

211. Banner Towing. An aircraft that is in full compliance with its type design and has an FAA-approved banner tow installation may be operated under a standard airworthiness certificate for banner towing purposes. An aircraft that has a standard airworthiness certificate and is modified for a special purpose operation must be operated under a multiple airworthiness certificate (standard/restricted) when the following conditions occur:

a. The special purpose modification does not meet the type design.

b. The special purpose modification is not approved for standard category use.

c. The aircraft will be operated outside the normal category operating limitations.

212. Reserved.

Section 2. Airworthiness Certificates

213. General. FAA Form 8100-2 and FAA Form 8130-7 will be referred to as being either a standard or a special classification within this order.

214. Classification and Category of Airworthiness Certificates.

a. Standard Classification. FAA Form 8100-2 may be issued for an aircraft that fully complies with all of the requirements for a standard airworthiness certificate in the category of normal, utility, acrobatic, commuter, or transport category, manned free balloons, or any other special classes of aircraft designated by the FAA.

b. Special Classification. FAA Form 8130-7 may be issued for an aircraft that does not meet the requirements for a standard airworthiness certificate. The certificate may be issued for an aircraft that meets the following:

(1) Primary. Aircraft that satisfies the requirements of 14 CFR § 21.184.

(2) Restricted. Aircraft that satisfies the requirements of 14 CFR § 21.185.

(3) Limited. Aircraft that satisfies the requirements of 14 CFR § 21.189.

(4) Provisional. Aircraft that satisfies the applicable requirements of 14 CFR part 21, subpart C, Provisional Type Certificates, and 14 CFR part 21, subpart I, Provisional Airworthiness Certificates.

(5) Light-Sport. Aircraft that meets the requirements of 14 CFR § 21.190.

(6) Experimental. For any category of aircraft, including amateur-built (14 CFR §§ 21.191, 21.193, and 21.195).

(7) Special Flight Permits. FAA Form 8130-7 may be issued for an aircraft that does not currently meet applicable airworthiness requirements, but is capable of safe flight, and meets the requirements of 14 CFR §§ 21.197 and 21.199.

215. Replacement, Exchange, or Amendment of Airworthiness Certificates.

a. Replacement.

(1) The FAA may issue a replacement airworthiness certificate when a certificate is declared lost, has been mutilated, is no longer legible, or contains inaccurate and/or erroneous information. The replacement airworthiness certificate must carry the original issue date of the certificate being replaced, preceded by a capital “R” in the Date block of the certificate. Replacement certificates also will be issued when the aircraft registration number has been changed, and the ASI must forward a copy of the replacement certificate and a copy of the Aeronautical Center Form 8050-64 to AFS-750. In these cases, a new application for airworthiness certification is not required.

(2) Request for a replacement certificate will be made to the local FAA office or, for air carriers, to the applicable certification office. The registered owner or certificate operator will certify this by submitting a signed statement containing the registration number (N-Number), serial number, make, and model of the aircraft, and a reason the replacement certificate is needed. Replacement of airworthiness certificates must not be accomplished by

*

*

*

*

verbal agreement with the assigned ASIs or through procedures contained in air carriers’ manuals that allow the continued operation of an aircraft without an airworthiness certificate. Such actions are contrary to 14 CFR §§ 91.203(b) and 121.153(a)(1), and 14 CFR part 135, Operating Requirements: Commuter and On-Demand Operations and Rules Governing Persons on Board Such Aircraft, 14 CFR § 135.25(a).

(3) A replacement airworthiness certificate may be issued without supporting documentation from AFS-750 if the date of issuance and the airworthiness classification and/or category of the lost or mutilated certificate can be positively established from the aircraft records, or from the remains of the certificate. If there is insufficient data on which to base issuance of the replacement certificate, the FAA ASI will obtain the required data electronically, by telephone, or by mail (such as the application form or previously issued airworthiness certificate) from AFS-750.

(4) Before issuing a replacement certificate, the FAA must review the aircraft records and, if necessary, inspect the aircraft to ensure that the applicant’s request is justified and the aircraft is eligible for the airworthiness certificate requested.

(5) Both a copy of the replacement certificate and a copy of the registered owner’s or certificate operator’s request for a replacement certificate (see paragraph 215a(2) of this order) or an Aeronautical Center Form 8050-64 (see paragraph 215a(1)) must be forwarded to AFS-750.

b. Amendment.

(1) A standard or special airworthiness certificate may be amended when there is—

(a) A modification to the aircraft, such as one that has been approved by an STC or amended TC, that changes the category of the aircraft specified in block No. 4 of the standard airworthiness certificate.

(b) A change to the exceptions specified in block No. 5 of the standard airworthiness certificate.

(c) A change in the aircraft model specified in block No. 2 of the standard airworthiness certificate.

(d) A change in the operating limitations for an aircraft with a special airworthiness certificate.

(e) A change in the aircraft model specified in block “D” of the special airworthiness certificate for those aircraft that have been issued a TC (for example, restricted, primary, limited).

(2) An ODA may amend a standard airworthiness certificate, if authorized to perform the function in accordance with 14 CFR §183.49.

(3) When a certificate is amended, the issuance date will be the current date. Also, the capital letter “A” will be typed in front of the date.

*

*

(4) Any amendment of an airworthiness certificate will require submission of FAA Form 8130-6. See paragraph 801 of this order for instructions on completing this form.

(5) Paragraph 217 of this order details further information on aircraft model changes.

(6) Operating limitations that were issued based on a previous edition of this order may be updated to include limitations contained in the current edition. The FAA does not require a new aircraft certification inspection for this type of administrative paperwork amendment (except as provided in paragraph 4107 of this order).

c. Exchange. It is highly desirable that all aircraft currently certificated in the standard category carry FAA Form 8100-2 to be consistent with the regulations. Owners and operators of general aviation and air carrier aircraft that still have FAA Form 1362A, Certificate of Airworthiness, should be encouraged to exchange such forms for the standard airworthiness certificate, FAA Form 8100-2. In exchanging these certificates, the operating certificate number will NOT be entered on the revised form. FAA Form 1362A will be attached to and forwarded with a copy of the revised certificate to AFS-750 to establish an official record of the exchange action. The foregoing exchange procedure also applies to FAA Form 8130-7, in lieu of FAA Form 1362B, Certificate of Airworthiness. The new airworthiness certificate will reflect the date as indicated on FAA Forms 1362A or 1362B, preceded by a capital “E” in the Date block of the certificate. The procedure to exchange a C of A (ACA-1362 (12-50)) does not apply to an expired C of A issued before July 17, 1956. Block 4 of FAA Form 1362 indicates the date of expiration. See the procedures in chapter 3 of this order for a standard airworthiness certificate.

216. Surrendered Airworthiness Certificate.

a. Airworthiness certificates voluntarily surrendered by written authorization from an aircraft owner or authorized representative must state why the certificate is being surrendered. The authorization and certificate must be forwarded to AFS-750 for retention in the permanent airworthiness files for that aircraft.

b. The airworthiness certificate must be surrendered to the FAA by the aircraft owner or operator as specified in 14 CFR § 21.335(e) when:

(1) The title of a U.S.-owned aircraft passes or has passed to a purchaser in another country, or

(2) The aircraft is leased for operations, registered in another country, and is removed from the U.S. registry.

Note: The exporting FAA representative will confirm deregistration and surrendered airworthiness certificate by reviewing the aircraft status on the FAA website. The FAA representative will make copies of these documents from the FAA website to complete their file.

217. Aircraft Model Change.

a. When an aircraft has been modified to conform to another model of the same make, the aircraft registration, airworthiness certificate, and aircraft ID plate must reflect the new model designation.

b. In addition to the existing ID plate, a new fireproof ID plate as specified in 14 CFR § 45.13 to include the new model designation must be attached as close as physically possible to the original ID plate without obscuring it.

c. To maintain an accurate and continuous operating history for the aircraft, the original ID plate must not be altered in any manner.

d. The normal procedures, including any applicable inspections, apply when processing FAA Form 8130-6. The amended airworthiness certificate will be identified with a capital “A” preceding the current date of the certificate being issued. If ownership of the aircraft has not changed, an application for aircraft registration, reflecting the new model designation, need not be submitted. AFS-750 will issue an amended registration certificate.

218. Safeguarding FAA Airworthiness Certificates. Airworthiness certificates are official forms and must be safeguarded by those FAA representatives who are charged with the responsibility for their issuance. Airworthiness certificates may not be produced in a computerized electronic format. Every measure must be taken to ensure these certificates are not obtained by unauthorized persons. At no time may a blank certificate be given to any unauthorized individual. Airworthiness certificates must be secured in a locked container when left unattended.

219. Recording of Conformity Inspections. FAA Form 8100-1, Conformity Inspection Record, must be used to document conformity inspections during type, production, and airworthiness certification programs (see figure 2-4 of this order).

a. Preparation. FAA Form 8100-1 must be prepared in accordance with the instructions shown on the back of the form.

b. Retention. FAA Form 8100-1, original or copy, should be retained by the managing office until it has been determined that it would serve no useful purpose.

220. Airworthiness Certification of Manned Free Balloons. Manned free balloons are type-certificated as complete aircraft consisting of three major articles: the envelope, the burner and fuel system, and the basket. The burner and fuel system and basket also are known as the “bottom-end” articles. Airworthiness certificates will not be issued for any individual article. The following are situations that may be encountered in certificating balloons in the standard category:

a. An applicant for a standard airworthiness certificate must present a complete system (three major components) for the purpose of making a determination of airworthiness.

* *

Section 3.

b. Many balloon TCDS require each individual balloon envelope to be assigned an individual aircraft serial number, aircraft data plate, and aircraft registration number. As such, the balloon manufacturer obtains a registration number from the FAA Aircraft Registry, assigns the N-Number to the aircraft, and reports the aircraft model and serial number to the FAA Aircraft Registry. When an eligible envelope is mated with the necessary articles to make a complete aircraft as described in the applicable TCDS, it is eligible for a standard airworthiness certificate.

c. Manufacturers of manned free balloons may deliver a balloon envelope when the envelope is the only article ordered. A balloon envelope that is manufactured, assembled to a burner and basket, and flight tested is eligible for a standard airworthiness certificate. The envelope, along with the standard airworthiness certificate and the logbook, may be delivered without the burner and basket. The envelope may then be assembled to a different burner and basket in accordance with the TC. A person may accomplish the interchange of the burner and basket as a preventive maintenance task as described below.

d. A new airworthiness certificate is not required when the aircraft is disassembled and a different burner and basket combination is installed, as allowed by the TC. Reassembly of the envelope and bottom-end articles into a complete aircraft may be performed as preventive maintenance under 14 CFR part 43, appendix A, paragraph (c)(27). The aircraft records must properly reflect the installation of the bottom-end articles and record the new empty weight. The bottom-end components must be in a current “annual or 100-hour” inspection status. The individual records of the bottom-end articles must be maintained. The due date of the next required inspection is determined based on the time the articles are due for inspection.

e. If an envelope is provided only as a replacement article without obtaining a new aircraft serial number, registration number, or ID data plate, the installation of the replacement envelope is a maintenance item under 14 CFR part 43. This requires appropriate documentation of the work performed and a return to service entry in the aircraft records by a person authorized to perform the maintenance. The aircraft ID data plate, serial number, and registration number are carried over from the previous aircraft envelope.

f. For model changes, see paragraph 217 of this order.

221. Reserved.

Section 3. Initial or Subsequent Issuance of Airworthiness Certificates

(Original/Recurrent) or Related Approvals

222. General. This section clarifies the terms “original” and “recurrent” as related to the issuance of airworthiness certificates or approvals. Also identified in this section are the FAA offices responsible for performing such functions, including, as appropriate, the cross-utilization of FAA inspection personnel.

a. A variety of airworthiness functions are performed by the FAA. Many of these functions must be accomplished by or coordinated with FAA manufacturing or airworthiness ASIs who have expertise in the particular specialty. These ASIs may include the principal ASI for a major aircraft manufacturer, or the principal maintenance or avionics ASI for an air carrier with aircraft

of the same type and complexity as the one for which certification is requested. A number of airworthiness functions can be accomplished by cross-utilization of the FAA. Cross-utilization by the FAA must be employed whenever possible in accordance with the guidance contained in this section.

b. The terms “original” and “recurrent” distinguish between those functions for which FAA manufacturing ASIs have primary responsibility and those for which FAA airworthiness ASIs have primary responsibility.

c. The FAA manufacturing ASI has primary responsibility for the issuance of original airworthiness certificates and approvals. The FAA airworthiness ASI has primary responsibility for the issuance of recurrent airworthiness certificates and approvals.

223. Airworthiness Certification.

a. Original Certification. The term “original certification” applies to the issuance of standard or special airworthiness certificates and approvals, including FAA Form 8130-4, Export Certificate of Airworthiness, for aircraft holding a U.S. type design for the following:

(1) Aircraft or related products or articles that have not left, and are under the control of, the original product manufacturer’s quality system.

(2) Aircraft or related products and articles for which an FAA airworthiness certificate or approval has never been issued. Examples include—

(a) Surplus military aircraft,

(b) Aircraft built from spare and/or surplus articles,

(c) U.S.-manufactured aircraft returning from another country without having been issued a U.S. airworthiness certificate or U.S. export airworthiness approval,

(d) Provisional airworthiness certificates and amendments thereto,

(e) Limited airworthiness certificates,

(f) Experimental airworthiness certificates, and

(g) Aircraft manufactured to other than U.S. requirements imported to the United States.

(3) Aircraft that previously have been issued an airworthiness certificate and presented for certification in another category or classification, for example; aircraft converted from standard to restricted for the first time or from a special airworthiness certificate to standard for the first time.

(4) Aircraft that have undergone changes to the type design and require flight testing, for example, under an experimental certificate for the purpose of showing compliance with regulations including, as applicable, the issuance or reissuance of a standard airworthiness certificate.

(5) Prototype or test articles to be used for design evaluation for TC or STC purposes. This includes articles or installation approvals.

(6) Aircraft with an FAA-approved type design that have undergone a model change, as listed on the airworthiness certificate, and require a conformity inspection before issuance of an amended airworthiness certificate.

(7) Issuance of special flight permits for aircraft that previously have not been issued an airworthiness certificate.

b. Recurrent Certification. The term “recurrent certification” applies to the issuance of standard or special airworthiness certificates or approvals for the following:

(1) Aircraft that previously have been issued an airworthiness certificate except those listed in paragraphs 223a(3) through (5) of this order.

(2) Issuance of special flight permits for aircraft that previously have been issued an airworthiness certificate.

(3) Export certification or approval of aeronautical products or articles that previously have been issued an airworthiness certificate or approval.

(4) Issuance of airworthiness certificates for aircraft with certificates that have expired, been surrendered, or been revoked.

(5) Changes to operating limitations.

(6) Issuance of experimental certificates for aircraft with expired experimental certificates issued for research and development (R&D) or exhibition.

(7) U.S.-manufactured aircraft returning to the United States that previously were issued an airworthiness certificate or an Export C of A in the United States.

(8) Aircraft manufactured to a U.S. TC and exported from a country with which the United States has a bilateral agreement, when accompanied by an Export C of A from a bilateral civil aviation authority (CAA). The CAA’s Export C of A must contain a statement from that CAA stating that the aircraft conforms to its U.S. type design and is in a condition for safe operation.

224. Exceptions.

a. Any requests, original or recurrent, for a special airworthiness certificate for LSA, amateur-built, exhibition, market survey, crew training, or air racing aircraft may be handled by FAA manufacturing ASIs, FAA airworthiness ASIs, or their authorized designees. If the responsible office cannot support the certification request, an appropriate delegation should be coordinated with the alternate office.

b. Any requests, original or recurrent, for an experimental certificate showing compliance with the regulations is the primary responsibility of the FAA manufacturing ASI or authorized designee. In remote areas or under special circumstances, an FAA airworthiness ASI may be delegated the authority by the Aircraft Certification Service if it is established that the person has had experience in type certification programs of a type and complexity comparable to the certificate requested.

225. Recording of Conformity Inspections. All inspections conducted by an ASI or designee to determine conformity to an approved type design before an airworthiness certificate is issued must be recorded on FAA Form 8100-1 (see paragraph 219 of this order).

226. Eligibility and Evaluation of U.S. Military Surplus Flight Safety-Critical Aircraft Parts (Articles) (FSCAP), Engines, and Propellers.

a. General.

(1) This paragraph provides guidance for use in evaluating and determining the eligibility of U.S. military surplus FSCAPs, engines, and propellers for installation on FAA type-certificated products. Many military surplus FSCAPs have the potential to be approved for installation on aircraft that hold special or standard airworthiness certificates.

(2) Military engines, propellers, and articles are categorized as new or used and fall into one of the following categories:

(a) Dual-use FSCAPs;

(b) Military-unique FSCAPs;

(c) Dual-use military surplus engines, propellers, and articles; and

(d) Military-unique surplus engines, propellers, and articles.

(3) Before these military engines, propellers, and articles are installed on type-certificated products, the installer must determine that they are:

(a) Eligible for installation, and

(b) Airworthy.

* *

(4) There are certain unique design considerations and FAA certification requirements for engines and propellers. Therefore, the eligibility and evaluation processes for military surplus engines, propellers, and articles are described separately in paragraph 226d of this order.

Note: For eligibility and evaluation of non-flight safety-critical articles, safety-critical aircraft articles, engines/propellers, and their articles, use AC 20-62, Eligibility, Quality, and Identification of Aeronautical Replacement Parts.

b. Dual-Use FSCAP (New or Used).

(1) Eligibility Screening. New or used dual-use FSCAPs may be eligible for installation on FAA type-certificated products with standard or special airworthiness certificates. The eligibility determination is made based on a review of the following pertinent Department of Defense (DOD) historical records:

(a) FSCAP identification: part number, DOD National Stock Number, and serial number.

(b) Manufacturer, DOD Commercial and Government Entity (CAGE) code, and date of manufacture.

(c) Total time-in-service.

(d) Current status of life-limited FSCAPs.

(e) Time since the last overhaul of each FSCAP that is required to be overhauled on a specified time basis.

(f) Identification of current inspection status, including time since last required inspection or maintenance performed.

(g) Current status of applicable AD and DOD directives (for example, engineering changes, technical orders, or maintenance work orders) including the date and method of compliance. If the AD involves recurring action, the current status includes the time and date when the next action is required.

(h) A list of current major alterations, repairs, or modifications for each FSCAP.

(i) Date any work was accomplished.

(j) Work authentication.

(2) Airworthiness Determination. After determining the FSCAP is eligible to be installed on a type-certificated product, the FSCAP must be evaluated to determine whether it is airworthy.

(a) New Dual-Use FSCAP.

1 For an FSCAP to be installed on products with standard airworthiness certificates, the FSCAP must conform to its FAA-approved type design and must be in a condition for safe operation.

(a) New Dual-Use FSCAP.

2 For an FSCAP to be installed on products with special airworthiness certificates, the FSCAP must be cited in the FAA-accepted maintenance manual and illustrated parts catalog (IPC) specified on the applicable TCDS, and must be in a condition for safe operation.

(b) Used Dual-Use FSCAP.

1 For an FSCAP to be installed on products with standard or special airworthiness certificates, the FSCAP must be evaluated using the procedures for new dual-use FSCAPs above, as appropriate, to determine the FSCAP’s airworthiness in accordance with 14 CFR § 43.13.

2 The FSCAP also must be evaluated by persons authorized under 14 CFR § 43.7(a), (c), (d), or (e) by using the following applicable methods, means, or data sources:

(aa) Differences between military and civil version (for example, possible DOD modifications, alterations, or repairs performed);

(bb) Current manufacturer or DOD technical data and procedures to perform tests and inspections, including current life-limited articles list;

(cc) Comparison of military time and/or cycle count for accumulated operational time versus civil (for example, “Did the military use a different method than civil operators to account for accumulated operational time?”);

(dd) Nondestructive tests, as required;

(ee) Bench test or functional test, as required;

(ff) Results of tests and inspections recorded;

(gg) Complete historical and modification, alteration, or repair records;

(hh) Manufacturer’s ID plate;

(ii) Flight, maintenance, and/or structural manual(s), and IPC; and

(jj) Instructions for Continued Airworthiness (ICAW).

(3) Approval for Installation. Persons authorized under 14 CFR § 43.7 may approve dual-use FSCAPs for installation on type-certificated products if the FSCAP successfully completed the eligibility screening and airworthiness evaluation. The installer must be able to determine that the installation of the FSCAP will leave the product in compliance with all regulations and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with 14 CFR § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

c. Military-Unique FSCAP.

(1) Eligibility Screening. New or used military-unique FSCAPs may be eligible for installation on civil aircraft with special airworthiness certificates under 14 CFR § 21.305(c) in conjunction with type certification procedures for a product or in accordance with a TCDS. Military-unique FSCAPs are not eligible for installation on a civil aircraft with a standard airworthiness certificate. The eligibility determination is made based on a review of the following pertinent DOD historical records:

(a) FSCAP identification: part number, DOD National Stock Number, and serial number.

(b) Manufacturer, DOD CAGE code, and date of manufacture.

(c) Total time-in-service.

(d) Current status of life-limited FSCAPs.

(e) Time since the last overhaul of each FSCAP that is required to be overhauled on a specified time basis.

(f) Identification of current inspection status, including time since last required inspection or maintenance performed.

(g) Current status of applicable ADs and DOD directives, (for example, engineering changes, technical orders, or maintenance work orders) including the date and method of compliance. If the AD involves recurring action, the current status includes the time and date when the next action is required.

(h) A list of current major alterations, repairs, or modifications for each FSCAP.

(i) Date any work was accomplished.

(j) Work authentication.

(2) Airworthiness Determination. After determining the FSCAP is eligible to be installed on a type-certificated product with a special airworthiness certificate, the FSCAP must be evaluated to determine whether it is airworthy.

(a) New Military-Unique FSCAP. The FSCAP must be cited in the FAA-accepted, military-approved maintenance manual and IPC specified on the applicable aircraft TCDS and must be in a condition for safe operation.

(b) Used Military-Unique FSCAP.

1 The FSCAP must be cited in the FAA-accepted, military-approved maintenance manual and IPC specified on the applicable aircraft TCDS and must be in a condition for safe operation.

2 The FSCAP also must be evaluated to determine airworthiness in accordance with 14 CFR § 43.13, by using the following applicable methods, means, or data sources:

(aa) Special equipment or test apparatus, as required;

(bb) Current manufacturer or DOD technical data and procedures to perform tests and inspections;

(cc) Comparison of military time and/or cycle count for accumulated operational time versus civil time (for example, “Did the military use a different method than civil operators to account for accumulated operational time?”);

(dd) Nondestructive tests, as required;

(ee) Bench test or functional test, as required;

(ff) Results of tests and inspections recorded;

(gg) Complete historical and modification, alteration, or repair records;

(hh) Manufacturer’s ID plate;

(ii) Flight, maintenance, and/or structural manual(s), and IPC; and

(jj) ICAW.

(3) Approval for Installation. Persons authorized under 14 CFR § 43.7 may approve military-unique FSCAPs for installation on type-certificated products if the FSCAP successfully completed the eligibility screening and the airworthiness evaluation. The installer must be able to determine that the installation of the FSCAP will leave the product in compliance with the TCDS and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with

14 CFR § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

d. Dual-Use and Unique Military Surplus Engines, Propellers, and Their Articles.

(1) New, used, or parted-out military surplus engines, propellers, and articles should not be presumed to be eligible for installation on FAA type-certificated aircraft. Military surplus engines, propellers, and articles are either dual-use or military-unique.

(2) The pertinent accompanying historical records documentation is essential for:

(a) The Defense Reutilization and Marketing Office’s (DRMO) public sale of engines, propellers, and articles;

(b) Categorizing the engines, propellers, and articles as dual-use or military-unique; and

(c) Establishing the eligibility and airworthiness of the engine, propeller, and articles.

(3) Military surplus engines and propellers may be type certificated under 14 CFR § 21.17, which requires issuance of a new TC and compliance with the applicable requirements, such as 14 CFR part 33, Airworthiness Standards: Aircraft Engines, for engines and 14 CFR part 35, Airworthiness Standards: Propellers, for propellers. For a military aircraft issued a TC under 14 CFR § 21.25 or § 21.27, the applicable engine or propeller is not required to be issued a separate TC. However, it should be noted that the engine and propeller cannot be certificated separately under these two sections. Any eligible military surplus engines or propellers will be referenced on the aircraft’s TCDS. However, military-unique surplus engines, propellers, and articles may be eligible for installation only on civil military surplus aircraft with special airworthiness certificates.

(4) Engines, propellers, and articles are deemed flight safety-critical if their failure, malfunction, or absence could cause a catastrophic failure resulting in loss or serious damage to the aircraft or an un-commanded engine shutdown resulting in an unsafe condition. Such conditions include, but are not limited to, release of engine or propeller debris, propeller separation, and, in rotorcraft, a transient or continuous power loss, or loss of power response. Examples of flight safety-critical engine and propeller articles are life-limited articles, rotating articles, and, for rotorcraft, actuating articles.

(5) Dual-Use Military Surplus Engines, Propellers, and Articles. Dual-use military surplus engines and propellers that hold a TC, and their articles, may be eligible for installation on civil products in accordance with the applicable regulations. The authorized individual completing the eligibility screening and/or the airworthiness evaluation should make a record entry to document the result(s).

(a) Eligibility Screening. New or used dual-use engines, propellers, and articles may be eligible for installation on FAA type-certificated civil or surplus military aircraft with standard or special airworthiness certification. A U.S. TC must have been issued for a

corresponding civil model engine or propeller under 14 CFR § 21.21 at the time of manufacture, or a U.S. aircraft TC must have been issued and the engines or propellers referenced in the aircraft TCDS under 14 CFR § 21.27 or § 21.25. The eligibility determination is made based on a review of the following pertinent historical records:

1 Engine, propeller, and article ID (article part number and serial number and manufacturer).

2 Contract or purchase order number under which the engine, propeller, or article was manufactured.

3 Evidence of engine, propeller, and article status, for example; serviceable or unserviceable, in accordance with DOD Form (DD Form) 1574-1 or Department of the Army (DA) Form 2410.

4 Complete historical records maintained by the military, the manufacturer, and any other prior owner(s), pertaining to inspection, modification, repair, alteration, maintenance, and operation of the engine from the time of acceptance by the military, including, but not limited to, DA Form 2408-5 and DA Form 2408-16. The maintenance records should also include the date on which the work was accomplished and work authentication.

5 Current status of applicable ADs and DOD directives (for example, engineering changes, technical orders, or maintenance work orders) including the date and method of compliance; and, if the AD involves recurring action, the time and date when the next action is required.

(b) Airworthiness Determination. After determining the article is eligible to be installed on a type-certificated product, the article must be evaluated to determine whether it is airworthy.

1 New Dual-Use Engines, Propellers, and Articles.

(aa) For engines, propellers, and articles to be installed on aircraft with standard airworthiness certificates, each engine, propeller, and article must conform to the approved TC, must have been manufactured under an FAA-approved production system, and must be in a condition for safe operation.

(bb) For engines, propellers, and articles to be installed for aircraft with special airworthiness certificates, each engine, propeller, and article must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted civil maintenance manual and IPC specified on the TCDS, and must be in a condition for safe operation.

2 Used Dual-Use Engines, Propellers, and Articles.

(aa) For engines, propellers, and articles to be installed on aircraft with standard airworthiness certificates, an evaluation should be performed by an FAA engineer or an appropriately authorized designated engineering representative (DER). When a DER is used, the DER’s recommendations or decisions must be substantiated in writing using FAA Form 8100-9,

Statement of Compliance With Airworthiness Standards, and include supporting documents. Each engine, propeller, and article must conform to the approved TC, must have been manufactured under an FAA-approved production system, and be in a condition for safe operation. In addition, the following should be evaluated:

(1) Operational differences between military and civil versions (for example, possible DOD modification, alteration, or repair performed) in performance standards as listed in the TCDS (for example, thrust, shaft horsepower, revolutions per minute (RPM), and ratings), and in specifications, as listed in the TCDS and the maintenance manuals (for example, fuel type, oil, weight).

(2) Complete historical operational records. This includes extreme operational conditions such as accidents, fires, or exceeding engine operating limits.

(3) Complete historical maintenance records; for example, modifications, alterations, and repairs, and complete documentation of work performed by an FAA-approved facility that was properly rated for the work performed and that conformed to the FAA-approved data.

(4) ICAW.

(5) Emission requirements as stated in the TCDS (engine only).

(6) Comparison of military time and/or cycle count for accumulated operational time and cycle versus civil (for example, “Did the military use a different method than civil operators to account for accumulated operational time and what are the expended equivalent civil cycles of the articles, taking into account their past operational history and mission profile?”).

(7) Current manufacturer’s technical data to perform tests or inspections.

(8) Written results of inspections performed (for example, maintenance record entry, FAA Form 8130-3, Authorized Release Certificate, or FAA Form 337, Major Repair and Alteration, for approval for return to service) and a completed FAA Form 8130-9, Statement of Conformity.

(9) The application of the identifying marking requirements in accordance with 14 CFR §§ 45.11 and 45.13, as applicable.

(10) Engine, propeller, or article overhaul records, including overhaul in accordance with civil engine/propeller manuals.

(11) Verification that the engine, propeller, or article was produced by an FAA PAH.

(bb) For engines, propellers, and articles to be installed on aircraft with special airworthiness certificates, an evaluation should be performed by an FAA engineer or an

appropriately authorized DER. When a DER is used, the DER’s recommendations or decisions must be substantiated in writing using FAA Form 8110-3, and include supporting documents. Each engine, propeller, and article must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted maintenance manual and IPC specified on the TCDS, and be in a condition for safe operation. In addition, the following should be evaluated:

(1) Complete historical operational records. This includes extreme operational conditions such as accidents, fires, or engine exceeding operating limits.

(2) Complete historical maintenance records; for example, modifications, alterations, and repairs, and complete documentation of the work performed.

(3) ICAW.

(4) Emission requirements as stated in the TCDS (engine only).

(5) Comparison of military versus civil time and/or cycle count for accumulated operational time and cycle (for example, “Did the military use a different method than civil operators to account for accumulated operational time and what are the expended equivalent civil cycles of the articles, taking into account their past operational history and mission profile?”).

(6) Current manufacturer’s technical data to perform tests or inspections.

(7) Written results of inspections performed (for example, maintenance record entry, FAA Form 8130-3, or FAA Form 337, for approval, for return to service) and a completed FAA Form 8130-9, signed by an authorized person.

(8) The application of the identifying marking requirements in accordance with 14 CFR §§ 45.11 and 45.13, as applicable.

(9) Engine, propeller, or article overhaul records, including overhaul in accordance with civil engine/propeller manuals.

(10) Verification that the engine, propeller, or article was produced by an FAA PAH.

(c) Approval for Installation. Persons authorized under 14 CFR § 43.7 may determine dual-use engines, propellers, or articles for installation if the engine, propeller, or article has successfully completed the eligibility screening and airworthiness evaluation. The installer must be able to determine that the use of the engine or propeller, and/or the installation of the article, will leave the aircraft in compliance with pertinent regulations and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with 14 CFR § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

(6) Military-Unique Engines, Propellers, and Their Military-Unique Articles. Military-unique engines, propellers, and articles are FSCAPs that were specifically and uniquely designed and manufactured for the U.S. military for which there originally was no corresponding FAA-approved PAH engine, propeller, or article for civil application.

(a) Eligibility Screening. New or used military-unique engines, propellers, and articles may be eligible for installation on surplus U.S. military aircraft type certificated under 14 CFR §§ 21.25(a) and 21.8 with special airworthiness certificates. The eligibility determination is made based on a review of the following pertinent DOD historical records:

1 Engine, propeller, article ID (article part number and serial number and manufacturer).

2 Contract or purchase order number under which the engine, propeller, or article was manufactured.

3 Evidence of engine, propeller, and article status; for example, serviceable or unserviceable, per DD Form 1574-1 or DA Form 2410.

4 Complete historical records maintained by the military, the manufacturer, and any other prior owner(s), pertaining to inspection, modification, repair, alteration, maintenance, and operation of the engine from the time of acceptance by the military, including, but not limited to, DA Form 2408-5 and DA Form 2408-16. The maintenance records also should include the date that the work was accomplished and work authentication.

5 Current status of applicable ADs and DOD directives (for example, engineering change, technical order, maintenance work order), including the date and method of compliance; and, if the AD involves recurring action, the time and date when the next action is required.

(b) Airworthiness Determination. After determining that the engine, propeller, or article is eligible to be installed on a surplus military aircraft with special airworthiness certificates, each engine, propeller, or article must be evaluated to determine whether it is airworthy.

1 New Military-Unique Engines, Propellers, and Articles. For new military-unique engines, propellers, and their associated articles to be installed on surplus military aircraft with special airworthiness certificates, each engine, propeller, and article must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted civil maintenance manual and IPC specified on the TCDS, and must be in a condition for safe operation.

2 Used Military-Unique Engines, Propellers, and Articles. For used military-unique engines, propellers, and articles to be installed on surplus military aircraft with special airworthiness certificates, each engine, propeller, and article must be evaluated by an FAA engineer or an appropriately authorized DER. When a DER is used, the DER’s recommendations or decisions must be substantiated in writing using FAA Form 8110-3, and include supporting documents. Each engine, propeller, accessory, and associated article

must be listed in the FAA-accepted, military-approved maintenance manual or FAA-accepted civil maintenance manual and the IPC specified on the TCDS, and must be in a condition for safe operation.

(c) Approval for Installation. Persons authorized under 14 CFR § 43.7 may approve military-unique engines, propellers, or articles for installation on surplus military aircraft with special airworthiness certificates if they have successfully completed the eligibility screening and airworthiness evaluation. The installer must be able to determine that the use of the engine or propeller, and/or the installation of the article, will leave the product in compliance with the TCDS and in a condition for safe operation. The authorized individual completing the eligibility screening and/or airworthiness evaluation must make a maintenance record entry that clearly documents the results of the evaluation. Each maintenance record entry in accordance with 14 CFR § 43.9 should include a description of the work performed, the completion date of the work performed, and the name of the person performing the work or authorized to sign.

Figure 2-1. Sample Aeronautical Center Form 8050-64, Assignment of

Special Registration Numbers

Figure 2-2. Sample Response Letter Regarding Identification Plates

U.S. Department of Transportation Federal Aviation Administration March 3, 2000 Mr. William Blue 220 West Broad St. Boston, MA 26204 Dear Mr. Blue: This is in response to your letter dated February 14, 2000, concerning disposition of the identification plate from Cessna Model 305A, Registration No. N5297G, Serial No. 305A-12345. The aircraft will be scrapped as a result of an accident. It is requested that the aircraft registration, airworthiness certificate, identification plate, and a copy of this letter be forwarded to the address listed below. Federal Aviation Administration Aircraft Registration Branch, AFS-750 Mike Monroney Aeronautical Center P.O. Box 25504 Oklahoma City, OK 73125-0504 Sincerely, John J. Doe Manager Burlington Manufacturing Inspection District Office

Figure 2-3. Sample Limitations for the Operation of an Aircraft

With a Door Removed

U.S. Department of Transportation Federal Aviation Administration Make … Model … Serial No … Registration No … AIRCRAFT OPERATING LIMITATIONS The aircraft described above may be flown with not more than one cabin door removed for the purpose of (see note below), provided the aircraft is operated in accordance with the applicable sections of Title 14 of the Code of Federal Regulations and the following limitations: Note: Show specific operations; for example, intentional parachute jumping, skydiving, etc.

1. Maximum speed not to exceed any of the following:

The approved maneuvering speed. 70 percent maximum level flight speed. 70 percent maximum structural cruising speed.

2. Aerobatic maneuvers are not permitted.

3. Maximum yaw angle 10 degrees; maximum bank angle 15 degrees.

4. A Federal Aviation Administration (FAA)-approved safety belt must be provided and worn by each occupant during takeoff and landing and at all other times when required by the pilot-in-command.

5. All occupants must wear parachutes when intentional parachute jumping and skydiving operations are conducted.

6. Smoking is not permitted.

7. When operations other than intentional parachute jumping and skydiving are conducted, a suitable guardrail or equivalent safety device must be provided for the doorway.

8. All loose articles must be tied down or stowed.

9. No baggage may be carried.

Figure 2-3. Sample Limitations for the Operation of an Aircraft

With a Door Removed (Continued)

10. Parachutists’ static lines must be kept free of pilot’s controls and control surfaces.

11. Operations are limited to visual flight rules conditions.

12. Cabin door hold-open clips installed on wing brace struts and/or under surface of wing must be removed before conducting intentional parachute jumping or skydiving operations.

13. When intentional parachute jumping, skydiving, or other specified operations are being conducted, the pilot at the controls must hold at least a private pilot certificate and appropriate rating.

14. This aircraft must not be operated in solo flight by the holder of a student pilot certificate.

15. Operation of this aircraft with a door removed for any purpose other than that for which it is certificated is prohibited.

16. The following placard must be placed on the instrument panel in full view of the pilot:

“For flight with door removed, see aircraft operating limitations dated … ”

17. A copy of these limitations must be carried in the aircraft when flight operations are conducted with the door removed.

18. These operating limitations are a part of the airworthiness certificate.

FAA Inspector … Date … Office No …

Figure 2-4. Sample FAA Form 8100-1, Conformity Inspection Record (Face Side Only)

4/16/2011 8130.2G

2-33

Section 1. General Information

Chapter 3. Standard Airworthiness Certification

Section 1. General Information

300. General. In no case may any aircraft be operated unless there is an appropriate airworthiness certificate issued to and valid for that aircraft. This chapter provides policy and guidance material associated with airworthiness certification and issuance of FAA Form 8100-2.

a. 14 CFR § 21.183(a) prescribes the basic requirements for issuance of standard airworthiness certificates for aircraft manufactured under a PC.

b. 14 CFR § 21.183(b) prescribes the basic requirements for issuance of standard airworthiness certificates for aircraft manufactured under a TC.

c. 14 CFR § 21.183(c) prescribes the basic requirements for issuance of the standard airworthiness certificates for an import aircraft type certificated in accordance with 14 CFR §21.21 or § 21.29 and produced under the authority of another State of Manufacture. The CAA certifications must be made by issuance of an Export C of A that contains either the certification statement noted on the corresponding FAA TCDS or a certification statement that the aircraft meets its FAA-approved type design and is in a condition for safe operation.

d. 14 CFR § 21.183(d) prescribes the basic requirements for issuance of standard airworthiness certificates for used aircraft (aircraft with time in service for other than production flight testing,) and for surplus aircraft of the U.S. Armed Forces.

e. 14 CFR § 21.183(h) prescribes the basic requirement for issuance of a standard airworthiness certificate for new aircraft manufactured to a TC, when the applicant does not hold the TC or a licensing agreement from the TC holder. A person seeking to manufacture a new aircraft under this provision must demonstrate to the FAA that the manufacturing began before August 5, 2004. Typically, these aircraft are built from spare and surplus articles. Paragraph 317 of this order provides detailed guidance for these aircraft.

Note: No FAA field office or FAA representative is authorized to waive regulatory requirements.

f. The FAA has full responsibility for finding that each aircraft, at the time an airworthiness certificate is issued, conforms to the type design and is in a condition for safe operation. Therefore, sufficient FAA inspections of each aircraft must be conducted by the certificating ASI or authorized designee.

301. Standard Airworthiness Certificate.

a. FAA Form 8100-2 ((Government Printing Office (GPO) pad only) is used for all original and recurrent certification of aircraft in the standard category only and for replacement of FAA Form 1362A still in effect. See chapter 8 of this order for instructions on completing FAA Form 8100-2 (see figure 3-1 of this order).

b. A standard airworthiness certificate remains valid as long as maintenance, preventive maintenance, and alterations are performed in accordance with 14 CFR parts 21, 43, and 91.

302. Application for Airworthiness Certificate. FAA Form 8130-6 is required whenever an airworthiness certificate is issued or amended. The application for a U.S. airworthiness certificate must be made by the registered owner or an agent who has a notarized letter of authorization (LOA) from the registered owner. The applicant must complete and sign the appropriate sections of FAA Form 8130-6 before submitting it to the FAA. Instructions for reviewing and completing FAA Form 8130-6 are found in chapter 8 of this order. Applicant instructions for completing FAA Form 8130-6 are contained in AC 21-12, Application for U.S. Airworthiness Certificate, FAA Form 8130-6.

303. Statement of Conformity.

a. FAA Form 8130-9 should be submitted to the FAA as required by 14 CFR §§ 21.53 and 21.130 under the following circumstances:

(1) By the applicant at the time the aircraft or articles thereof are submitted for FAA tests during the type certification program;

(2) By the applicant for each aircraft, aircraft engine, or propeller submitted for type certification; or

(3) By a TC holder or licensee manufacturing products under a TC—

(a) with the initial transfer of ownership of each product,

(b) upon application for the original issue of an airworthiness certificate, or

(c) an export airworthiness approval.

Note: For the purpose of this order, type certification programs include any tasks associated with the issuance of a TC or STC or the approval of FAA Form 337.

b. The FAA should review FAA Form 8130-9 for completion and ensure that all of the entries are typewritten or printed legibly in permanent blue or black ink. The form also must be signed in permanent blue or black ink by an authorized person who holds a responsible position in the manufacturing organization. If the certifier is also an FAA designee, the designee title should not be used. If the inspection and certification is delegated to a supplier by the applicant, a copy of the letter of delegation must be submitted to the FAA at the time of conformity.

304. Use of Parts Catalogs and Maintenance Manuals.

a. When an aircraft is submitted for airworthiness certification, a determination must be made that the aircraft is in conformance with its type design. This does not imply that every article must be subjected to a conformity inspection. Conformity inspections should only be conducted when, in the FAA’s judgment, conformity to the type design for a particular article cannot be substantiated by any other means.

b. Conformity to the type design can only be established when a determination has been made that the article(s) conform to FAA-approved design data.

c. Parts catalogs or maintenance manuals may not be used to conduct conformity inspections. However, they should be used when applicable as an aid in establishing the configuration of a particular aircraft or in determining that the aircraft has been properly maintained.

d. MIDOs, MISOs, and CMOs/certificate management units (CMU) having certificate management responsibility for a particular manufacturer interface with the applicable aircraft certification office (ACO) to provide technical data and other pertinent information necessary to support the certification process. It is the applicant’s responsibility to provide the type design data for those products and articles for which a conformity determination must be made.

305. Basic Eligibility Requirements. Before a standard airworthiness certificate can be issued, the applicant must show the following:

a. The aircraft conforms to its approved type design and is in a condition for safe operation.

b. Any major alterations were accomplished in accordance with an approved STC or other FAA-approved data.

c. The aircraft complies with all applicable ADs.

d. If altered while in another category, the aircraft continues to meet, or has been returned to, its approved type design configuration and is in a condition for safe operation.

Continue reading ↓ 120 of 868 passages shown