Radar Vectors
FAA Order Cancelled Issued Aug 30, 2005 AIR-140 141 pages Copy saved Nov 18, 2026

Order 8100.9A FAA authorized as a Designated Alteration Station DAS, Delegated Option Authorization DOA, and Special Federal Aviation Regulation SFAR 36 holder

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

ORDER 8100.9A DAS, DOA, AND SFAR 36 AUTHORIZATION PROCEDURES

August 30, 2005

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

Distribution: A-W(IR/FS/VN)-3; A-X(CD/FS)-3;A-FFS-5-7(MAX); Initiated By: AIR-100/AIR-200/AFS-300 A-FAC-1,3,4(STD); AMA-220 (20 copies); AMA-250 (15 copies) AFS-600 (10 copies); AVR-20 (ALL); AEU-100/200 (1 copy)

RECORD OF CHANGES DIRECTIVE NO. 8100.9A

CHANGE

TO

SUPPLEMENTS

OPTIONAL

CHANGE TO

SUPPLEMENTS

OPTIONAL

BASIC BASIC

FAA Form 1320-5 (6-80) USE PREVIOUS EDITION

Associate Administrator, Aviation Safety, AVS-1

8100.9A

FOREWORD This order establishes the procedures, guidance, and limitations of authority for organizations that the Federal Aviation Administration (FAA) authorizes as a Designated Alteration Station, Delegation Option Authorization holder, or Special Federal Aviation Regulation 36 holder. The Aircraft Certification Directorates, Aircraft Certification Offices, and Flight Standards personnel use this order as an aid in the administration of these organizations. This order contains guidance material for the organizations and is intended to provide a better understanding of the functions authorized and procedures to be followed when exercising the authority granted to them by the FAA. If you find any deficiencies, need clarification, or want to suggest improvements on this order, send a copy of FAA Form 1320-19, Directive Feedback Information (written or electronically), to the Aircraft Certification Service, Planning and Financial Resources Management Branch, AIR-530, Attention: Directives Management Officer. Form 1320-19 is on the last page of this order. You may also send a copy to the Aircraft Engineering Division, AIR-100, Attention: Comments to Order 8100.9A. If you urgently need an interpretation, contact AIR-140 at (405) 954-4103. Always use Form 1320-19 to follow up each verbal conversation.

Nicholas A. Sabatini Associate Administrator, Aviation Safety, AVS-1

Page i (and ii)

8/30/05 8100.9A

TABLE OF CONTENTS CHAPTER 1. GENERAL

Paragraph Page 1-1. Purpose … 1 1-2. Distribution … 1 1-3. Cancellation … 1 1-4. Effective Date … 1 1-5. Significant Changes … 1 1-7. Authority to Change this Order … 1 1-8. Deviations … 1 1-9. Related Publications … 1 1-10. Definitions … 2 1-11. Acronyms … 3 1-12. Forms/Letters/Formats … 4 1-13. Records Management … 4

CHAPTER 4. DELEGATED ORGANIZATION EVALUATION PROGRAM

CHAPTER 2. SELECTION AND APPOINTMENT

2-1. General … 5 2-2. Application … 5 2-3. Selection Process … 5 2-4. Authorization … 6

CHAPTER 3. OVERSIGHT

3-1. Oversight Program … 7 3-2. Organization Management Team (OMT) … 7 3-3. Supervision … 7 3-4. Conducting Supervision … 8 3-5. Delegated Organization Evaluation Program … 10 3-6. Corrective Action … 10 3-7. Geographical Coordination … 11

CHAPTER 4. DELEGATED ORGANIZATION EVALUATION PROGRAM

4-1. Evaluation Program Overview … 13 4-2. Evaluation Scheduling … 13 4-3. Evaluation Planning … 14 4-4. Performing the Evaluation … 15 4-5. Post-Evaluation Activity … 17 Figure 4-1. Evaluation Disagreement Resolution Flow Chart … 18

CHAPTER 5. DAS/DOA/SFAR 36 QUALIFICATIONS, RESPONSIBILITIES, AND AUTHORITY

5-1. General … 19 5-2. Qualifications … 19 5-3. Responsibility … 19 5-4. Memorandum of Understanding … 20

Page iii

8100.9A 8/30/05

TABLE OF CONTENTS-CONTINUED

Paragraph Page

5-5. Staff Authority and Responsibility … 20 5-6. Functions Not Delegated … 20 5-7. Staff Qualification Requirements … 21 5-8. Procedure Manual … 22 5-9. Training … 22 5-10. Duration of Appointments … 23 5-11. Self-Evaluation … 23 5-12. Manufacturing Work Activity … 24

CHAPTER 6. DESIGNATED ALTERATION STATIONS

6-1. General … 25 6-2. DAS Authorized Functions … 26 6-3. DAS Procedure Manual Requirements … 32

CHAPTER 7. DELEGATION OPTION AUTHORIZATION

7-1. General … 35 7-2. DOA Authorized Functions … 36 Figure 7-1. DOA Type Certification Process … 37 7-3. DOA Procedure Manual Requirements … 42

CHAPTER 8. SFAR 36 AUTHORIZATIONS

8-1. General … 47 8-2. Development of Major Repair Data … 47 8-3. SFAR 36 Procedure Manual Requirements … 48

CHAPTER 9. DESIGNEE INFORMATION NETWORK

9-1. General … 49 9-2. Designation Form … 49 9-3. Authorization Numbers … 49 9-4. Functions Summary … 49 9-5. FAA Internal Comments Form … 49

CHAPTER 10. TERMINATION

10-1. General … 51 10-2. Cause for Termination of Designations … 51 10-3. Procedures for Termination and Appeal of a DOA, DAS, or SFAR 36 … 51 10-4. No Response from DOA, DAS, or SFAR 36 … 52 10-5. Surrender of Designation … 52 10-6. Coordination of Termination Decisions … 52 10-7. Designee Information Network Status … 52

Page iv

8/30/05 8100.9A

TABLE OF CONTENTS-CONTINUED Paragraph Page APPENDIX 1. SAMPLE FORMS AND LETTERS (22 PAGES)

Figure 1. Sample Denial Letter … 1 Figure 2. Sample Form 8100-10, DAS, DOA, or SFAR 36 Statement of Qualifications … 2 Figure 3. Sample DAS Authorization Letter … 3 Figure 4. Sample DOA Authorization Letter … 4 Figure 5. Sample SFAR 36 Authorization Letter … 5 Figure 6. Sample Memorandum of Understanding-All Authorizations … 6 Figure 7. Sample FAA Form 8100-9 Used for DAS Data Approval … 8 Figure 8. Sample FAA Form 8100-9 Used for DOA Data Approval … 9 Figure 9. Sample FAA Form 8100-9 Used for DOA Approval in Support of STC Applicant … 10 Figure 10. Sample FAA Form 8100-9 Used for DOA Repair Data Approval … 11 Figure 11. Sample FAA Form 8100-9 Used for SFAR 36 Compliance Finding … 12 Figure 12. Sample Summary Activity Report … 13 Figure 13. Sample Delegated Organization Supervision Record … 15 Figure 14. Sample Evaluation Notification Letter … 17 Figure 15. Sample DAS/DOA/SFAR 36 Evaluation Discrepancy Record … 18 Figure 16. Sample Evaluation Report Cover Sheet … 19 Figure 17. Sample Evaluation Survey Sheet … 20 Figure 18. Sample Evaluation Report Transmittal Letter … 22

APPENDIX 2. SAMPLE DAS, DOA, SFAR 36 PROCEDURE MANUAL (12 PAGES)

APPENDIX 3. CERTIFICATION PLANS (2 PAGES)

Figure 1. DAS Certification Plans … 1 Figure 2. DOA Certification Plans … 2

APPENDIX 4. SAMPLE CONFORMITY PLAN (4 PAGES)

APPENDIX 5. EVALUATION CRITERIA (39 PAGES)

Page v (and vi)

RELATED PUBLICATIONS. › Advisory Circular (AC) 21-23, Airworthiness Certification of

8/30/05 8100.9A

CHAPTER 1. GENERAL

1-1. PURPOSE. This order prescribes the Federal Aviation Administration (FAA) procedures governing organizations authorized as a Designated Alteration Station (DAS), Delegation Option Authorization (DOA), or Special Federal Aviation Regulation Number 36 (SFAR 36).

1-2. DISTRIBUTION. This order is distributed to the branch levels of the Aircraft Certification Service, Flight Standards Service, and the Office of Aviation System Standards in Washington Headquarters; to the branch level in the Aircraft Certification Directorates and the Regional Flight Standards Divisions; to the International Field Offices (IFOs) and the Flight Standards District Offices (FSDOs); to all Aircraft Certification Offices (ACOs) and all Manufacturing Inspection District and Satellite Offices (MIDOs and MISOs); to the Flight Standards Branch and Aircraft Certification Branch at the FAA Academy; to the Suspected Unapproved Parts Program Office; and to the Brussels Aircraft Certification Staff.

1-3. CANCELLATION. Order 8100.9, DAS, DOA, and SFAR 36 Authorization Procedures, dated August 7, 2002, and Order 8100.12, Designated Alteration Station Program Limitations, dated December 24, 2002, are canceled.

1-4. EFFECTIVE DATE. FAA managing offices must immediately adopt the practices contained herein related to selection and oversight of DAS, DOA, and SFAR 36 authorizations. Any changes requiring revisions to procedures manuals must be implemented within one year as agreed to by the delegated organization and their managing FAA office.

1-5. EXPLANATION OF CHANGES. The significant changes in this revision are:

a. Revised oversight processes and requirements for supervision of the Authorization Holder.

b. Established a new evaluation program that evaluates all aspects of an authorization holder’s performance.

c. Revised evaluation program criteria.

d. Incorporated the requirements previously found in Order 8100.12 regarding off-site DAS project management.

e. Clarified when SFAR 36 data may be used to approve repairs for return to service.

f. Require all managers of authorized representatives to read and understand the memorandum of understanding.

g. Specify when consultants and supplier personnel may act as authorized representatives for DOA Holders.

h. Incorporate revisions related to the renumbering of FAA Form 8100-8, which is now FAA Form 8100-10.

1-6. BACKGROUND. Title 49 United States Code section 44702(d), authorizes the FAA Administrator to delegate matters related to the examination, testing, and inspection necessary to issue certificates, and the issuance of certificates. Title 14 of the Code of Federal Regulations (14 CFR) part 21 subparts J and M, and Special Federal Aviation Regulation (SFAR) No. 36 prescribe the rules for Delegation Option Authorizations, Designated Alteration Stations, and SFAR 36 delegations. The FAA issues these authorizations to qualified organizations to assist the FAA in matters related to type certification, supplemental type certification, airworthiness approvals, and major alterations and repairs. Any authorization is a privilege granted by the Administrator and it is not the right of every qualified applicant to be granted a DAS, DOA or SFAR 36 authorization.

1-7. AUTHORITY TO CHANGE THIS ORDER. The Aircraft Certification Service, Aircraft Engineering Division (AIR-100), the Production and Airworthiness Division (AIR-200), and the Flight Standards Service, Aircraft Maintenance Division (AFS-300) has the authority to revise or cancel material in this order. Depending on the change, the appropriate FAA office (AIR-100, AIR-200, and AFS-300) will initiate the change and coordinate with the other offices.

1-8. DEVIATIONS. Adherence to procedures in this order is necessary for uniform administration of this directive. Any deviations from this guidance material must be coordinated and approved by AIR-100/200, and AFS-300 as applicable. If deviation is necessary, the FAA employee involved should ensure that deviations are substantiated, documented, and concurred with by the appropriate supervisor and approved by AIR-100, AIR-200, or AFS-300 as appropriate.

1-9. RELATED PUBLICATIONS.

a. Advisory Circular (AC) 21-23, Airworthiness Certification of Civil Aircraft, Engines, Propellers, and Related Products Imported into the United States

Par 1-1 Page 1

8100.9A 8/30/05

b. AC 21-40, Application Guide for Obtaining a Supplemental Type Certificate

c. Order 2150.3, Compliance and Enforcement Program

d. Order 4040.26, Aircraft Certification Service Flight Safety Program

e. Order 8100.7, Aircraft Certification Systems Evaluation Program

DEFINITIONS. For the purposes of this directive the followi › Designated Alteration Station (DAS). A repair station, air

f. Order 8100.8, Designee Management Handbook

g. Order 8100.14, Interim Procedures for Working with the European Community on Airworthiness Certification and Continued Airworthiness

h. Order 8110.4, Type Certification

i. Order 8110.37, Designated Engineering Representative (DER) Guidance Handbook

j. Order 8120.2, Production Approval and Certificate Management Procedures

k. Order 8130.2 Airworthiness Certification of Aircraft and Related Products

l. Order 8130.21, Procedures for Completion and use of the Authorized Release Certificate, FAA Form 8130-3, Airworthiness Approval Tag

m. Order 8300.10, Airworthiness Inspector’s Handbook

n. Order 8430.21, Flight Standards Division, Aircraft Certification Division. And Aircraft Evaluation Group Responsibilities

NOTE: Publications throughout this order refer to the latest revision level.

1-10. DEFINITIONS. For the purposes of this directive the following definitions apply:

a. Administrator. When spelled with a capital “A” refers to the FAA Administrator. When spelled with a lower case “a” refers to the delegation administrator.

b. Aircraft Flight Manual (AFM). Either the Airplane Flight Manual or Rotorcraft Flight Manual (as applicable).

c. Appeal Panel. Two or more office managers and a senior engineer, inspector or flight test pilot assigned the task of determining if the appointment process was conducted properly in the event of an applicant’s appeal of the FAA’s decision.

d. Appointing Office. The Aircraft Certification Office (ACO) and/or Flight Standards District Office (FSDO) having selection and appointment responsibility for the authorization holder.

e. Authorization Letter. A FAA letter specifying the delegation’s authorized functions, and any associated limitations.

f. Authorized Representative (AR). Any individual within the DOA, DAS, or SFAR 36 who is authorized in the procedure manual to make findings of compliance, determination of conformity, or airworthiness on behalf of the FAA.

g. AR Trainee. An individual who meets all the requirements for a staff AR except for direct experience working with the organization. AR trainees must not make findings, which are not subsequently verified and approved by either, a staff AR or the FAA.

h. Authorization Holder. The organization or company holding the certificate that provides the eligibility for the DAS, DOA, or SFAR 36 authorization.

i. Compliance Inspection. Compliance inspections are physical inspections performed to review an installation and its relationship to other installations on a product to determine compliance with 14 CFR/CAR requirements, which cannot be determined adequately from an evaluation of the technical data.

j. Conformity Inspection. Conformity inspections verify and provide objective documentation that test articles, parts, assemblies, installations, functions, and test set ups conform to the design data.

k. Corrective Action. The measures taken to resolve unsatisfactory conditions and to prevent reoccurrence.

l. DAS/DOA/SFAR 36 Administrator. The focal point(s) for the authorization holder who is responsible for managing the DAS/DOA/SFAR 36 activities and communicating with the OMT.

m. Delegation Option Authorization (DOA). A manufacturer holding a current type certificate and production certificate issued under standard procedures that is authorized by the FAA to conduct type, production, and airworthiness certification functions in accordance with 14 CFR part 21, subpart J.

n. Designated Alteration Station (DAS). A repair station, air carrier, or manufacturer authorized by the FAA to issue supplemental type certificates in accordance with 14 CFR part 21, subpart M.

Page 2 Par 1-9

GENERAL › ACRONYMS. The following is a list of acronyms used in this

8/30/05 8100.9A

o. Designee Information Network (DIN). The Designee Information Network is an automated information system designed to support the delegation management process by providing a consolidated delegation information repository for tracking pertinent delegation data.

p. Delegated Organization. Refers to DAS, DOA, and SFAR 36 organizations.

q. Evaluation Panel (EP). The Evaluation Panel should be comprised of the prospective Organization Management Team (OMT) in order to determine the appropriateness of the appointment or denial.

r. Flight Standards District Office (FSDO). As used in this order refers to any responsible Flight Standards office, such as the Certificate Management Office, or Certificate Holding District Office.

s. Manufacturer. Holder of a production certificate, approved production inspection system, parts manufacturer approval or Technical Standard Order Authorization.

t. Manufacturing Inspection District Office (MIDO). As used in this order refers to any responsible manufacturing office such as MIDO, Manufacturing Inspection Satellite Office, or Certificate Management Office.

u. Objective Evidence. All the means by which any alleged fact tends to be established or disproved. These means must be factual, convincing, relevant, valid, reliable, and complete.

v. Organization Management Team (OMT). The team of FAA personnel responsible for oversight of the DAS, DOA or SFAR 36, and the projects or functions they perform.

w. OMT Lead. Focal point for the OMT who is selected by the managing ACO.

x. Procedure. A specific way to perform an activity or function that is documented and usually contains the purposes and scope of the activity or function: what is to be done and by whom; when, where, and how the activity or function is to be done; the materials, equipment, and documents to be used; and how the activity or function is to be controlled and recorded.

y. Root Cause. The underlying cause of a noncompliance or unsatisfactory condition, usually identified through analysis.

z. Special Federal Aviation Regulation Number 36 (SFAR 36). A repair station, air carrier, or commercial operator authorized to develop and use major repair data

that are not specifically approved by the FAA Administrator in accordance with SFAR 36. (Find SFAR 36 at the beginning of 14 CFR part 121.)

1-11. ACRONYMS. The following is a list of acronyms used in this order:

14 CFR Title 14 of the Code of Federal Regulations ACO Aircraft Certification Office AEG Aircraft Evaluation Group AFS Flight Standards Service AIR Aircraft Certification Service AFM Aircraft Flight Manual AFMS Aircraft Flight Manual Supplement AP Appeal Panel AR Authorized Representative CMO Certificate Management Office DAR Designated Airworthiness Representative DAS Designated Alteration Station DER Designated Engineering Representative DIN Designee Information Network DMIR Designated Manufacturing Inspection Representative DOA Delegation Option Authorization EP Evaluation Panel FAA Federal Aviation Administration FSDO Flight Standards District Office (includes CMO or Certificate Holding District Office) ICA Instructions for Continued Airworthiness MIDO Manufacturing Inspection District Office (includes manufacturing CMO or Manufacturing Inspection Satellite Office – MISO) MOU Memorandum of Understanding OMT Organization Management Team PLR Production Limitation Record PNL Program Notification Letter SFAR Special Federal Aviation Regulation STC Supplemental Type Certificate STIR Supplemental Type Inspection Report TCDS Type Certificate Data Sheet TC Type Certificate/Type Certification TIA Type Inspection Authorization TIR Type Inspection Report

Par 1-10 Page 3

8100.9A 8/30/05

1-12. FORMS/LETTERS/FORMATS. Appendix 1, Sample Forms and Letters, provides examples of appropriate forms, letters, and formats referenced in this order.

1-13. RECORDS MANAGEMENT. For guidance on retaining or disposing records, see FAA Orders 0000.1, FAA Standard Subject Classification System; 1350.14, Records Management; and 1350.15, Records, Organization, Transfer, and Destruction Standards. Or, see your office Records Management Officer/Directives Management Officer.

GENERAL › RECORDS MANAGEMENT. For guidance on retaining or disposing

Page 4 Par 1-12

8/30/05 8100.9A

CHAPTER 2. SELECTION AND APPOINTMENT

2-1. GENERAL. This chapter describes how to select and appoint DAS, DOA, and SFAR 36 authorized organizations.

2-2. APPLICATION.

a. Application. Applications will be submitted to the appointing office in accordance with the applicable regulations. The application letter must state the authorization and limitations sought, including the products on which the authorization will be utilized.

SELECTION PROCESS. › Formation and Review by the Evaluation Panel. After determi

(1) DAS and DOA applicants must submit applications to the geographical ACO. The ACO should provide a written response within 30 calendar days to the applicant, acknowledging receipt and providing an estimated date to complete their evaluation.

(2) SFAR 36 applicants must submit applications to their managing FSDO. The FSDO inspector assigned should follow the procedures in Order 8300.10 for the coordination of the application with the ACO.

b. Application Content. The application must include:

(1) FAA Form 8100-10, DAS, DOA, or SFAR 36 Statement of Qualifications.

(2) A cover letter stating the authority requested under the applicable regulations and limitations for the authorization, to include the products on which the authorization will be utilized. The cover letter must also contain a brief statement as to the applicant’s eligibility in accordance with applicable regulations.

(3) A detailed description of how the qualification requirements are satisfied as defined in paragraph 5-2 of this order, and the specific eligibility requirements as defined in chapters 6 through 8 of this order (for example, having a TC, PC, 14 CFR part 145, 14 CFR part 121).

(4) The authorization holder administrator’s resume as outlined in paragraph 5-7a.

(5) AR Packages. Authorized Representatives are not designees under the requirements of 14 CFR part 183. However, ARs perform functions comparable to designees. Before recommending ARs to the FAA, the organization must evaluate the proposed AR’s qualifications using the applicable criteria in Order 8100.8, Designee Management Handbook, for the function(s) the ARs will be performing. The organization’s

AR selection process must be defined in their procedure manual and meet the intent of the selection process found in Order 8100.8. The organization’s application should contain evidence of the organization’s review of the proposed ARs, and a summary of each AR’s qualifications. The organization need not submit AR qualification summaries for existing designees, unless the proposed functions (to include type and complexity) were not previously delegated to the AR.

(6) A procedure manual that includes the content required by paragraph 5-8 of this order, and the specific detail outlined in the Procedure Manual example in appendix 2, Sample DAS, DOA, SFAR 36 Procedure Manual, of this order.

2-3. SELECTION PROCESS.

a. Initial Screening. After receiving the application, the ACO (DAS and DOA) or FSDO (SFAR 36) will determine if the applying organization meets the following basic requirements:

(1) The FAA needs the new appointment.

(2) The organization holds the current certificates defined in the eligibility sections of chapters 6 through 8, as the basis for the authorization in accordance with the FAA regulations.

(3) The organization has a successful and recent history with the FAA for the functions desired and is familiar with the applicable FAA certification processes.

(4) The organization’s staff possesses integrity, sound judgment, and a cooperative attitude toward the FAA.

b. Formation and Review by the Evaluation Panel. After determining that the applicant is eligible, the appointing office must organize a panel of FAA personnel to evaluate the application. The team may consist of the accountable directorate representative, the geographic MIDO Principal Inspectors (PI), FSDO, appropriate Aircraft Evaluation Group (AEG) representatives, and appropriate ACO personnel. The panel must be qualified and familiar with the functional areas for which the delegation is sought and experienced with the appropriate DAS/DOA/SFAR 36 processes. The Evaluation Panel (EP) should be comprised of the prospective Organization Management Team (OMT) (see chapter 3) in order to determine the appropriateness of the appointment or denial. The panel will collectively

Par 2-1 Page 5

SELECTION AND APPOINTMENT › AUTHORIZATION. After completing all elements of the selecti

8100.9A 8/30/05

determine if the applicant is qualified for the authorization. The panel must consider the following criteria to determine whether an authorization is warranted:

(1) The FAA must need the appointment.

(2) The FAA must have adequate personnel to properly oversee and support the appointment.

(3) The applicant must employ, or have available, qualified engineering, flight test, and inspection personnel as appropriate.

(4) The applicant must have adequate facilities appropriate to the authorization desired.

(5) The applicant’s administrator and ARs must have integrity, sound judgment, and a cooperative attitude.

c. Evaluation of Authorized Representatives (ARs). The FAA managing offices should review the AR packages to ensure the proposed ARs meet the criteria of Order 8100.8. Existing FAA designees may be approved as AR staff members without further technical review of their qualifications if they will be performing similar functions.

d. Procedure Manual Approval. After determining that the applicant is qualified, the EP must review the proposed procedure manual and ensure it establishes a process that complies with the applicable requirements of 14 CFR, and applicable FAA orders. After the EP approves the procedure manual, the managing office(s) shall execute the Memorandum of Understanding with the officials of the organization as described in paragraph 5-4.

e. Denial of DOA/DAS/SFAR 36 Applications. Denial of an application for a DOA/DAS/or SFAR 36 authorization must be made in writing to the applicant and sent via registered mail within 30 calendar days of the decision. The letter of denial must explain the specific reasons for the denial and detail what steps the applicant may take before the FAA will reconsider their application. (See appendix 1, figure 1 for an example of a denial letter.)

f. Appeal Panel (AP). If denied, an applicant may request appeal of the decision. The applicant must appeal the denial in writing within 60 calendar days of being notified of the denial. The AP will consist of at least two office managers and a senior engineer or inspector, or flight test pilot who were not part of the applicant’s EP. The AP will consider all available information and may interview the applicant, applicant’s staff, EP personnel, or may invite other persons to be resources at their deliberations. The AP reaches a decision by consensus and all decisions are final.

g. Appeal Panel Authority. The AP may uphold the previous decision; or

(1) Override the previous decision with a new decision and provide appropriate justification; or

(2) Request that any part of the appointment process be repeated citing new information that the EP must review, or issue additional instructions and clarifications to the EP. The AP may direct that the previous EP conduct the review, or it may direct the appointing office to appoint a new EP.

h. Functioning of the Appeal Panel. The AP shall determine if the appointment process was conducted properly by reviewing the documentation in the appellant’s file, the evaluation panel’s written justification, interviewing members of the EP, and reviewing other information deemed appropriate. If discrepancies are found, appropriate actions shall be taken to ensure the future integrity of the appointment process. The AP shall complete their deliberations by consensus within 60 calendar days from the date of the appeal. The decision must be documented and signed by each AP member and transmitted to the appointing office manager. The appointing office manager will notify the appellant of the decision by the AP by letter. If the AP is not able to reach a decision by consensus within the 60 day period, the appointing office manager will make the final decision and notify the appellant. The decision is final whether made by the AP or appointing office manager.

2-4. AUTHORIZATION. After completing all elements of the selection process (including signature of an MOU), the appointing office shall provide the applicant proof of authorization. Proof of authorization shall be an authorization letter issued by the appointing ACO and coordinated with the MIDO and AEG for DAS and DOA, and jointly signed between the ACO and certificate managing FSDO for SFAR 36 authorizations. The authorization letter shall note the authorization number from the Designee Information network (DIN), the limitations of the authorization, the location of facilities, and any technical limitations. The nature and scope of authorization limitations may be of any form appropriate to the authorization. It may be limited for lack of certain equipment, or limited to certain types of products. Examples of authorization letters are in appendix 1, figures 3, 4, and 5. The appointing office shall also provide the names and phone numbers of the OMT members.

NOTE: The appointing ACO inputs the appropriate information into DIN. (See chapter 9.)

Page 6 Par 2-3

Managing the Organization’s Activity. › Managing DOA and DAS Activity. The final step in authorizin

8/30/05 8100.9A

CHAPTER 3. OVERSIGHT 3-1. OVERSIGHT PROGRAM. FAA oversight is a systems approach to managing and supervising the organization. The FAA focuses on the organization’s performance and its approved systems and procedures. Oversight consists of supervision, addressed in this chapter, and evaluations, addressed in chapter 4. The FAA will oversee the organization as necessary to ensure that it performs adequately. The program consists of supervising and evaluating the organization’s:

a. Systems and procedures.

b. Personnel.

c. Projects and activity

d. Overall performance

3-2. ORGANIZATION MANAGEMENT TEAM (OMT). This team of FAA personnel supervises and evaluates the organization’s functions. The OMT includes the ACO, AEG, MIDO, and Flight Standards District Office (FSDO) as needed to oversee the organization. The OMT members must be knowledgeable and experienced in the organization’s functions.

a. The OMT lead coordinates the OMT’s activity and is the primary focal point for communication with the organization. The ACO manager selects the OMT lead.

b. Aircraft Certification Office OMT members have primary responsibility for oversight of the administrator, the engineering and flight test functions, and the certification procedures in the procedure manual. The OMT must include ACO flight test pilots and engineers from all technical disciplines that the authorization holder performs.

c. Manufacturing OMT members have primary responsibility for oversight of the inspection and airworthiness procedures and functions of DASs and DOAs.

d. The FSDO is responsible for certificate management of repair stations and operators that are DASs or SFAR 36s. The FSDO must inform the OMT of any changes in the authority or capability of the repair station or operator.

e. The Aircraft Evaluation Group (AEG) supports the OMT for maintenance and operational issues on DAS and DOA projects.

3-3. SUPERVISION. Supervision provides guidance, direction, training and performance feedback through interactions with the organization. Supervision consists of the following:

a. Managing the Organization’s Activity.

(1) Defining and Understanding the Organization’s Authority and Limitations. The organization’s authority and limitations establish what types of functions the organization may perform. The regulations establish the general authority and limitations, which are further defined in the procedure manual. The OMT must ensure that the authority and limitations are appropriate based on the organization’s capability, experience and history.

(2) Approving the Organization’s Procedures and Personnel. By approving the procedures and personnel, the FAA ensures that the organization’s procedures are adequate to ensure compliance, and that the organization uses technically qualified personnel in the process. The OMT must:

(a) Approve Procedure Manual Changes. Procedure manual changes may address changes in the processes for performing functions; changes in the procedures or the organization’s system to satisfy FAA regulations and policy; or changes in the organization’s staff. Procedure manual changes must be approved prior to implementation.

(b) Approve AR Changes. The OMT must find proposed ARs acceptable before they can perform any functions for the organization. The OMT should verify that the organization used the process described in its procedure manual to evaluate proposed ARs (or changes in existing AR’s authority) and validate its conclusions. The OMT must tell the authorization holder if the proposed AR is approved or denied within 15 working days of receiving the proposed change.

(3) Managing DOA and DAS Activity. The final step in authorizing DAS and DOA activity occurs by review of the program notification letter. At this time the OMT decides if the organization can perform the functions required to accomplish the project. The OMT must review each program notification letter and determine if FAA involvement is required in the program. Chapters 6 and 7 define required FAA involvement. The OMT may decide to delegate other aspects of the program, or retain parts for FAA approval. The OMT should participate in a project if there is any

Par 3-1 Page 7

OVERSIGHT › CONDUCTING SUPERVISION. The OMT supervises the organization

8100.9A 8/30/05

question of the organization’s ability to complete any aspect of the project.

b. Guidance and Feedback.

(1) Providing Guidance. The OMT helps all authorized organizations get required directive and policy material. Access to most FAA regulations, directives, and ACs of interest to authorization holders is available on the Internet at http://www.airweb.faa.gov/rgl. The OMT should provide copies of policy information and interpretive material not available via the Internet. The OMT should provide the information and instruction the organization needs to perform its authorized functions.

(2) Providing Feedback. The OMT must provide the organization feedback on its performance. The OMT must notify the organization of any problems with its performance as soon as possible. The OMT must document all items that require formal corrective action as described in paragraph 3-6.

c. Assessing Performance.

(1) Reviewing the Organization’s Work. As determined necessary, the OMT must review the organization’s work and data for accuracy and completeness. The OMT bases the amount of review on the organization’s experience, the quality of work performed on previous projects, and the AR performing the function. Previous service difficulties and the violation history of the organization should be considered when determining the amount of review necessary. The OMT must review samples of completed project records (for example, airworthiness, conformity, compliance, and type design data). The OMT should coordinate any meetings or inspections through the authorization holder’s administrator.

(2) Review of Self-Evaluations. The OMT must review periodic self-evaluation reports, including the organization’s plan for corrective action, for possible discrepancies. The OMT lead must acknowledge receipt of the report, coordinate the review with the other OMT members, and coordinate corrective actions per paragraph 3-6 if necessary.

(3) Verifying Compliance with Procedures. The OMT must ensure the authorization holder complies with the approved procedure manual and referenced internal processes.

d. Maintaining Oversight Documentation. Proper documentation provides the FAA with the necessary information to oversee the organization properly. It also provides a history of the organization’s performance in case OMT members change or the organization seeks additional authority.

(1) The OMT lead will maintain a file containing the following information for each authorization that they manage OMT members must provide any information not available to the OMT lead:

(a) Completed DAS, DOA, SFAR 36 application package.

(b) Evaluation panel documentation and rationale.

(c) Copy of the letter of authorization.

(d) General correspondence (non-project specific).

(e) Copy of the current procedure manual.

(f) Supervision records and evaluation reports.

(g) Copy of summary activity reports (if applicable).

(h) Copy of current Forms 8130-13 for out-of-geographic-area work since the last reporting period, if applicable. The manufacturing OMT member must provide copies of FAA Form 8130-13.

(i) Enforcement History.

(j) Copies of the organization’s selfevaluation.

(k) Copies of the organization’s A-3 operations specifications showing the status of ratings, capabilities and limitations (Repair Stations and Operators).

(2) The other OMT members should maintain files documenting their specific activity in support of the OMT. Their files should include the following:

(a) Certificate Management records for any manufacturing approvals held by the organization.

(b) Copies of supervision records completed.

(c) Documentation of their input regarding projects performed by the organization.

3-4. CONDUCTING SUPERVISION. The OMT supervises the organization by continuously performing the tasks in paragraph 3-3. The OMT may conduct supervision visits at the facility at any time. The OMT performs these tasks by interacting directly with the organization and its ARs, or by reviewing the organization’s approvals and data. The level of supervision depends on the organization’s experience,

Page 8 Par 3-3

CONDUCTING SUPERVISION. The OMT supervises the organization › Flight Standards Supervision. Flight Standards OMT members

8/30/05 8100.9A

history, and past-performance. It also depends on the technical complexity and impact on safety of the functions that the organization performs. OMT members must complete a Delegated Organization Supervision Record (appendix 1, figure 13) of all significant supervision activities or communications with the organization.

a. Required Evaluation Items. The OMT must annually assess the required evaluation items on the supervision record. The OMT should meet at the beginning of the annual period to establish a strategy for assessment of these items. The strategy should consider which OMT members are responsible for the assessment of the different items.

b. Coordinating Supervision Activity. Supervision of the organization must be coordinated among the OMT. The OMT lead is primarily responsible for coordinating supervision of the organization. The type of coordination may vary depending on the size and complexity of the organization and OMT. If the OMT consists of only a few people, it may be appropriate to inform all OMT members of any activity related to the organization. For larger organizations, like DOA holders, it may be more practical to coordinate fully within technical disciplines, which would report their activity and findings to the OMT Lead. The entire OMT should decide exactly how it will coordinate its activity. In any case, the OMT members must provide the OMT lead with supervision records documenting their supervision visits to the organization.

c. Planning Supervision Visits. The OMT members should notify the OMT Lead of any planned supervision activity at the organization’s facility. The OMT lead should notify the administrator of the organization of the planned visit. Unannounced visits may be made at the discretion of the OMT. OMT members should coordinate their visits if possible, to minimize the impact to the organization. If the visit is to a repair station or operator, the flight standards OMT member should be informed before the visit.

d. Engineering Supervision. The OMT can accomplish most engineering supervision by data review. This does not require on-site visits to the organization’s facility. However, at least one engineering OMT representative must make at least one supervision visit to the organization’s facility each year, in addition to the evaluation requirements in chapter 4. If time allows, the OMT member may combine the supervision visit with a specific project activity, such as witnessing tests or participating in flight tests. The primary reason for the visit is to:

(1) Review approved test plans and compliance substantiation data, type design data, etc.

(2) Discuss self-evaluation results.

(3) Review corrective actions implemented.

(4) Review project files.

(5) Review internal training and training records.

(6) Review AR selection procedures and records.

(7) Provide the latest guidance and policy.

(8) Interact with the ARs.

e. Manufacturing Supervision. The OMT accomplishes manufacturing supervision primarily by direct interaction with the organization and visits to their facility. The OMT may tailor the number of visits to the organization, but they must visit at least annually. These visits are in addition to the evaluation requirements of chapter 4. The OMT should base the number of needed visits on the organization’s experience and adequacy of previous certification efforts. Frequency also depends on the organization’s size, level of activity, and past performance. Smaller organizations or those with lesser activity or no performance problems may need only one or two manufacturing visits a year, while others with increased complexity may need frequent visits. During visits to the facility the OMT member should:

(1) Determine compliance to regulatory requirements.

(2) Identify safety issues.

(3) Observe ARs perform airworthiness or conformity inspections.

(4) Discuss self-evaluation results.

(5) Review corrective actions implemented.

(6) Review project files.

(7) Review internal training and training records.

(8) Review AR selection procedures and records.

(9) Provide latest guidance and policy.

(10) Interact with the ARs.

f. Flight Standards Supervision. Flight Standards OMT members oversee the activity of those organizations that are repair station or operators. See Order 8300.10 for the certificate management processes for these organizations. The Flight Standards OMT member does not need to notify the OMT of all their activity at the facility, but must inform the OMT

Par 3-4 Page 9

CORRECTIVE ACTION. The OMT must ensure the organization imp › Regulatory Non-compliances. Any violations of the regulatio

8100.9A 8/30/05

members of any findings that may affect the organization’s ability to act as a delegated organization. Changes in the ratings, limitations or capabilities of the organization can affect their authority as a DAS or SFAR 36.

g. Aircraft Evaluation Group Supervision. The AEG’s primary activities are to coordinate and review the Instructions for Continued Airworthiness, and support the ACO in determining operational suitability. Since the FAA does not delegate AEG functions to the organization, supervision activity by the AEG is usually limited to their participation during the certification program. The AEG will not normally visit the facility, but may do so if they determine a visit is necessary.

h. Documenting Supervision on the Delegated Organization Supervision Record. The OMT must document supervision activity and significant communications with the organization on the supervision record in appendix 1, figure 13. The record is used to document general supervision activity, and ensure that any unsatisfactory performance is documented and corrected.

(1) Required Evaluation Items. The OMT must evaluate the items listed on the record at least annually. Each OMT member must evaluate each of the items applicable to their technical discipline. Not every interaction with the organization needs to be recorded, but every supervision visit to the organization’s facility must be recorded. The OMT member performing the supervision should rate each item assessed as satisfactory, unsatisfactory, or not applicable. If the evaluation item is not assessed during the activity, leave the item blank. Corrective action must be implemented for all items rated as unsatisfactory.

(2) Text Blocks on Back of Form.

(a) Summary of Visit or Communication. Provide a summary of activity performed during the visit or of important communications not otherwise documented with the organization. For visits, the summary should include details on how the evaluation items were assessed.

(b) Notable Conditions Encountered. Highlight the notable conditions encountered. “Notable conditions” means any items or conditions of interest that do not require corrective action, but need documentation. These may be items to assess during the next visit, or areas of interest to other OMT members.

(c) Items Requiring Corrective Action. Describe here any evaluation item rated as unsatisfactory, or any other condition determined to need corrective action. Provide specific details of any unsatisfactory conditions and check the box on the front page indicating corrective action is required. The OMT lead must assess

items identified as needing corrective action. If the OMT lead concurs that corrective action is required, they must notify the authorization holder per paragraph 3-6.

i. Coordinating Supervision Visit Findings with the Authorization Holder. The OMT member performing the supervision activity should communicate their observations with the administrator of the organization (if possible) and any ARs involved in the activity reviewed. The authorization holder should be told of any items identified as needing corrective action and informed that they will be further notified of such items.

3-5. DELEGATED ORGANIZATION EVALUATION PROGRAM. The evaluation program evaluates all aspects of the authorization holder’s performance. It assesses both system-level procedures and compliance, and the authorization holder’s technical proficiency and judgment. The OMT uses these evaluations to assess if the organization’s procedures are adequate, if the organization complies with the procedures and if the ARs are making acceptable technical decisions. The OMT must evaluate the authorization holder using the program requirements in chapter 4.

3-6. CORRECTIVE ACTION. The OMT must ensure the organization implements corrective action for noncompliances and any problems with the organization’s procedures or performance.

Page 10 Par 3-4

a. Regulatory Non-compliances. Any violations of the regulations (other than non-compliances with the airworthiness standards) or SFAR 36 by the authorization holder require notification and corrective action per Order 2150.3. These violations could be discovered during evaluation of the authorization holder or during oversight of their activity. For example, if the DAS or DOA issued experimental certificates without obtaining approval of the limitations from the FAA, it would be a violation of 14 CFR § 21.275 or § 21.475. Additionally, any instances where DAS authorization holders did not comply with the requirements of their procedures manual when developing an STC would be a violation of 14 CFR § 21.463.

NOTE: The OMT lead should be familiar with the FAA’s compliance and enforcement program. If they are not, the OMT lead should coordinate any compliance and enforcement activity with other members of the OMT who are familiar with the program’s requirements. Manufacturing and flight standards OMT members usually have experience with compliance and enforcement activity.

OVERSIGHT › GEOGRAPHICAL COORDINATION. Project activity in different ge

8/30/05 8100.9A

b. Non-compliances to the Airworthiness Standards or Possible Unsafe Conditions. If an approval performed by the organization results in a possibly unsafe product, or a product not meeting the airworthiness standards, the OMT must immediately notify the organization of the unsafe condition or non-compliance and:

(1) Assess the safety effect of the condition to determine if the FAA needs to issue an Airworthiness Directive to correct the condition on products in operation.

(2) Pursue Airworthiness Directive action if necessary.

(3) Review the procedures that led to the approval, and verify the procedures are adequate and that qualified ARs performed them.

(4) Require the organization to determine the root cause of the condition and whether the problem is systemic or isolated in nature. The organization must report on the cause within 30 calendar days.

NOTE: The FAA can only mandate changes to products through the Airworthiness Directive process. If non-compliant conditions do not result in an unsafe condition, the OMT can request that the organization correct the condition. The OMT should document when an organization refuses to implement corrective action for non-compliant conditions. The OMT should consider this refusal when assessing the organization’s performance.

(5) Verify corrective and remedial action is implemented.

c. Other Conditions Requiring Corrective Action. The OMT lead must notify the authorization holder of any condition requiring corrective action. The OMT must document the condition in the FAA’s files, and notify the authorization holder of the item in writing within 30 calendar days of identifying the condition. The letter should task the organization to identify the cause of the condition and propose corrective action within 30 calendar days. The OMT must maintain the organization’s response and any related correspondence in the FAA’s files.

d. Follow-Up on Corrective Action. The OMT must track and reevaluate all items requiring corrective action. An OMT member must visit the organization’s facility to ensure the organization implements corrective action. Verification of corrective action must be documented on a supervision record.

3-7. GEOGRAPHICAL COORDINATION. Project activity in different geographical areas may require support from the different FAA offices responsible for the off-site facilities. The OMT lead will coordinate with the FAA

offices having geographical responsibility. Together they can supervise at the additional facility.

Par 3-6 Page 11 (and 12)

Determining Frequency of Evaluations. Evaluations must be p › Request by the organization.

8/30/05 8100.9A

CHAPTER 4. DELEGATED ORGANIZATION EVALUATION PROGRAM 4-1. EVALUATION PROGRAM OVERVIEW. The evaluation program evaluates all aspects of the authorization holder’s performance. It combines what were separate technical evaluations and Aircraft Certification System Evaluation Program evaluations. Aircraft Certification System Evaluation Program evaluations will only be performed on production approval holders (see Order 8100.7). This evaluation program assesses both system-level procedures and compliance, and the authorization holder’s technical proficiency and judgment. The evaluations are a means for the FAA to ensure the authorization holders have developed and complied with the appropriate procedures for their delegated functions, and are making technical decisions that are acceptable and technically correct.

a. The ACO managers will:

(1) Select the evaluation team-leader.

(2) Select engineering team members.

(3) Coordinate scheduling of evaluations for their delegated organizations.

b. The MIDO managers will select manufacturing team members.

c. The OMT members will:

(1) Conduct evaluations when selected as evaluation team members.

(2) Ensure corrective action is implemented for findings.

(3) Monitor evaluation findings to identify trends within an organization.

d. The Delegation and Airworthiness Programs Branch, AIR-140, manages and coordinates the evaluation program, and will:

(1) Manage the program database.

(2) Coordinate program information with other responsible headquarters organizations.

(3) Analyze the database information to identify engineering-related trends discovered during evaluations.

(4) Provide requested data to other FAA organizations.

(5) Serve as the engineering focal point for the delegated organization evaluation program.

(6) Identify and correct delegation program and policy deficiencies.

(7) Participate in a limited number of evaluations each year.

e. The Production Certification Branch, AIR-220, will:

(1) Serve as the production and airworthiness focal point for the delegated organization evaluation program.

(2) Analyze the database information to identify manufacturing-related trends discovered during evaluations.

(3) Identify and correct delegation program and policy deficiencies related to manufacturing.

(4) Promote standardization by participating in a limited number of evaluations each year.

f. The Aircraft Maintenance Division, AFS-300, will:

(1) Serve as the flight standards focal point for the delegated organization evaluation program.

(2) Analyze the database information to identify trends discovered during evaluations.

(3) Identify and correct delegation program and policy deficiencies related to flight standards.

(4) Promote standardization by participating in a limited number of evaluations each year.

4-2. EVALUATION SCHEDULING.

a. Determining Frequency of Evaluations. Evaluations must be performed at least every two years. Evaluations may be scheduled more frequently, and unscheduled evaluations may be conducted whenever the OMT determines necessary. The OMT must use their judgment and discretion when determining the need for evaluations. Factors which might warrant decreasing the interval between evaluations or an unscheduled evaluation include:

(1) Request by the organization.

Par 4-1 Page 13

8100.9A 8/30/05

(2) Significant change in the ARs at the delegated organization.

(3) Significant changes in the organization’s capabilities or facilities.

(4) Accidents or incidents resulting from design approvals the organization issued.

(5) A significant number of service difficulties or operator complaints about an approval the organization issued.

Evaluation Team Skills. The evaluation team should be famil › Certification Procedures. The team members must understand

(6) Significant number of technical noncompliances on previous projects.

(7) Significant findings from the organization’s self-evaluation.

(8) Significant changes in the activity level of the organization.

(9) Airworthiness Directives resulting from approvals issued by the organization.

(10) Administrator’s position in the company could affect their FAA responsibilities.

(11) Complaints by the organization’s employees.

(12) Significant off-site activity.

b. Schedule Planning. The OMT lead should schedule and budget evaluations for the following 12 months by the end of the fiscal year. The OMT lead must coordinate with the authorization holders, necessary OMT members, and other needed evaluators to ensure they’re available for the dates scheduled. If the organization is also scheduled for an Aircraft Certification Systems Evaluation Program evaluation, the evaluations may be scheduled consecutively, to minimize the impact to the organization and allow for FAA resources to support both evaluation programs. The OMT lead must provide the projected schedule – and any changes throughout the year – to the Delegation and Airworthiness Programs Branch, AIR-140. AIR-140 will coordinate the schedule with the schedule planners for the Aircraft Certification System Evaluation Program.

4-3. EVALUATION PLANNING.

a. Composition of Evaluation Team.

(1) Team Leader. Since one of the primary purposes of the evaluation program is to ensure a minimum level of oversight by the OMT, the OMT should usually participate in the organization. If the ACO manager wants an evaluation independent of the OMT, they may occasionally schedule evaluations using

non-OMT members. The team leader should normally be the OMT lead, but the ACO manager may select a different team leader at their discretion. The team leader should have experience in conducting both process and technical evaluations, and understand the certification and approval processes being evaluated. The team leader must have the communication and management skills necessary to direct the evaluation team’s activity. The team leader should also have all skills required of the evaluation team members, as described in paragraph 4-3b.

(2) Evaluation Team. The evaluation team may consist of the OMT members or the ACO and MIDO managers may substitute other personnel for the OMT members and supplement them with additional resources. The team members must be technically proficient in the areas they are responsible to evaluate. There must be MIDO members and ACO representatives for each technical discipline that is being evaluated. The team may utilize technical specialist support from other ACOs, headquarters, directorates or chief scientific and technical advisors as needed to support the evaluation. The managing flight standards personnel for repair station/operator DASs and SFAR 36s should be notified of the evaluation and invited to participate or perform oversight visits during the evaluation. Participation of the AEG depends on their level of participation during the organization’s projects. If the AEGs review all of the content of ICA packages developed during a project, there is no need for them to participate. If, however, they routinely accept the ICA without review or depend on the authorization holder to develop the ICA, they should participate in the evaluation. More than one AEG organization may need to participate on the evaluation, depending on the types of products for which the organization is responsible.

b. Evaluation Team Skills. The evaluation team should be familiar with the following:

(1) Delegated Organization Evaluation Program. The team members should be familiar with the fundamentals of FAA delegation and the FAA’s procedures for managing delegated organizations. They must also be familiar with the purpose of the evaluation and the criteria used during the evaluation. They can gain this knowledge by attending the Delegation Management course at the FAA Academy or participating in previous evaluations.

(2) Certification Procedures. The team members must understand the certification requirements of Orders 8110.4, 8130.2, and so on, as applicable to the functions they are evaluating. They can get this knowledge by attending Aircraft Certification courses at the FAA Academy, on the job training, and participation in previous certification projects.

Page 14 Par 4-2

PERFORMING THE EVALUATION. › Evaluation In-Briefing. The team leader, and the evaluation

8/30/05 8100.9A

(3) Technical Proficiency. The team member must have the technical proficiency to properly evaluate the areas of responsibility assigned during the evaluation. They can get this knowledge by education, attending FAA Academy core job functions courses, or participation in previous certification projects.

(4) Auditing Skills. The team members should have skills necessary to perform the evaluation, such as in communication, sampling of data, asking questions. They may get this skill by participating in previous audits or evaluations, such as Aircraft Certification System Evaluation Program evaluations, National Aviation Safety Inspector Program evaluations, or Principal Inspector evaluations. Evaluators may also obtain these skills by attending ISO-9000 series training.

c. Evaluation Length. The length of the evaluation must be tailored according to the level of activity at the organization and their approvals’ safety impact. Evaluations will usually be scheduled for one week, including travel. Time at the organization’s facility depends on the evaluator’s travel arrangements. The time scheduled must be adequate to evaluate all projects selected for review.

d. Notification. The evaluation team lead will notify the authorization holder using the sample format in appendix 1 figure 14. For normally scheduled evaluations, they should notify the authorization holder in writing no later than 50 calendar days before the evaluation. They should notify authorization holders of non-scheduled evaluations as soon as possible. Evaluations may be performed without notification if the OMT believes necessary. The OMT must get concurrence from AIR-100, who will coordinate with AIR-200, and AFS-300 that the evaluation is necessary without notification.

e. Team Coordination and Selection of Projects for Review.

(1) Notifying Team Members of the Evaluation. The team leader notifies the evaluation team of the evaluation and coordinates evaluation scheduling with the other members.

(2) Assigning Responsibilities to Evaluation Team. Before the evaluation starts, the evaluation team should agree to the evaluation plans, personnel assignments and responsibilities, and so on. The team should evaluate all system elements and as many criteria as possible during the evaluation. See appendix 5 for evaluation criteria. They can evaluate procedural criteria before the evaluation by reviewing the organization’s procedures and verify compliance with procedures during the evaluation.

f. Selection of Projects to Evaluate. The evaluation team should select projects to be reviewed before the evaluation. The team should also consider if there would be any test witnessing, inspections, and so on, during the evaluation. The projects should technically represent the projects the organization performed and address all technical areas. The team may review other projects during the evaluation at the team leader’s request. The evaluation team should review the results of any previous Aircraft Certification or Flight Standards Service evaluations and the supervision records for the authorization holder and ensure they focus on areas where deficiencies were identified, or could be expected.

g. Evaluation Plan. The team leader must prepare a written evaluation plan that includes the following information. The OMT lead will provide any information not readily available to the team leader.

(1) Name and address of the organization and type of delegated organization.

(2) Dates of evaluation.

(3) Access information, including facility point of contact.

(4) Lodging information.

(5) Equipment required (for example, notebook computer, safety shoes, and coveralls).

(6) Names of team leader and members.

(7) Description of projects being evaluated.

(8) Identification of the administrator and key staff.

(9) Date of the approved procedure manual.

(10) FAA/facility written agreements in effect.

(11) Listing of the previous evaluation’s discrepancies and respective follow-up action.

(12) Special emphasis items recommended by the OMT.

(13) Team member assignments. This should identify the responsibility of each team member and the criteria they are responsible to evaluate.

4-4. PERFORMING THE EVALUATION.

a. Evaluation In-Briefing. The team leader, and the evaluation team, should provide a briefing to the authorization holder when they arrive at their facility. The authorization holder’s administrator, senior

Par 4-3 Page 15

PERFORMING THE EVALUATION. › Evaluation Wrap-Up. Near the end of the evaluation, the tea

8100.9A 8/30/05

management, and selected ARs should attend. The briefing should cover the evaluation’s purpose, the procedures to be followed, and introduction of the evaluation team members.

b. Evaluation Coordination with Authorization Holder. The FAA evaluation team leader and the authorization holder’s evaluation representative (usually the administrator for the authorization) should agree upfront on how to handle communication issues.

c. Evaluation Details. The evaluation team will evaluate the selected projects using the applicable criteria in appendix 5. The authorization holder should make copies of data, if requested, for use by the evaluation team. The evaluation team should evaluate all system elements and as many of the criteria as possible. Some criteria related to procedures may only need evaluation by one team member, or a engineering and manufacturing team member. For example, a single person from each discipline may evaluate the procedure manual. Other criteria, like the system element “Design Data Approval”, will be evaluated by the engineering team members of all technical disciplines. Each evaluator should be knowledgeable of all the criteria applicable to the system element assigned to be evaluated, and evaluate as many of criteria as possible.

d. Coordination with Managing FSDO PI. The team leader will inform the certificate management inspector of the progress of the evaluation, if possible. The team leader should coordinate with the PI to determine when these discussions should occur.

e. FAA team meetings must be held daily to review the progress of the evaluation and discuss issues that arise. Team members should frequently contact each other during the evaluation to ensure they are investigating those issues that cross technical specialties, and are coordinating the issues properly. The team should review all discrepancies found during the evaluation.

f. Meeting with the Organization’s Representative. The team will hold a brief meeting daily with the organization’s evaluation representative to discuss the evaluation’s progress, including problems encountered, the status of actions the team requested, schedule changes, and coordination of other evaluation activities.

g. Documentation of Discrepancies. The team should document discrepancies found during the evaluation on the Evaluation Discrepancy Record in appendix 1, figure 15. Ensure all applicable blocks are complete. Ensure true copies of objective evidence are attached to the appropriate discrepancy forms, appropriately referenced, and clearly identified per

Order 2150.3, Compliance and Enforcement Program (if necessary).

h. Classification of Discrepancies. Identify discrepancies as safety-related if the possibility of an unsafe condition exists as a result of the discrepancy. Any safety-related discrepancy must be further investigated by the ACO to determine if an Airworthiness Directive is needed. Discrepancies related to the technical data package should be documented according to the following:

(1) Airworthiness Standard Non-compliance. Discrepancies that show that the approval does not meet the airworthiness standards.

(2) Regulatory Non-compliance. Discrepancies that indicate a non-compliance with the regulations other than the airworthiness standards. For example, if a DAS authorization holder did not submit the names of staff members to the FAA before they approved data, it violated 14 CFR § 21.441(b).

(3) Procedures Manual Non-compliance. Discrepancies that indicate the organization did not comply with the FAA-approved procedure manual (including referenced internal processes) in effect at the time of the discrepancy.

(4) FAA Policy Non-compliance. Discrepancies that indicate a non-compliance with related FAA documents, such as orders, notices, policy memos, and handbook bulletins.

(5) Technical Discrepancies. Technical discrepancies in the compliance or data package, such as math errors, inadequate compliance determination, or using technical analysis when a test is required.

(6) FAA Procedures Manual Discrepancy. Discrepancies in the FAA-approved procedures manual (including referenced internal processes). The manual does not comply with the requirements of this order, or the manual’s procedures are inadequate or incomplete to perform a process.

(7) Special Emphasis Items. Any other condition that needs further action.

i. Evaluation Wrap-Up. Near the end of the evaluation, the team leader will hold a final meeting. The team leader will allow time to finalize the details of the evaluation. The team leader and members must complete all required Evaluation Discrepancy Records and complete the Evaluation Survey Sheet of appendix 1, figure 17. The team will discuss discrepancies to determine if there are any possible regulatory violations. The team leader will resolve any disagreement between team members on any discrepancy.

Page 16 Par 4-4

POST-EVALUATION ACTIVITY. › Dispute Resolution. If the organization disagrees with a di

8/30/05 8100.9A

j. Out-Briefing/Presentation of Findings. At the end of the evaluation, the team leader will conduct a briefing to review all discrepancies identified during the evaluation with the authorization holder. At least the administrator and senior management of the authorization holder should attend. Other ARs are welcome. FAA team members will attend, unless the FAA team leader excuses them. The team leader should invite the Flight Standards PI. The briefing should explain the process to correct or dispute the discrepancies and encourage the authorization holder to submit any feedback regarding the evaluation to AIR-140.

4-5. POST-EVALUATION ACTIVITY.

a. Preparing the Evaluation Report. Within 20 calendar days after the evaluation the team leader will prepare a report outlining the discrepancies identified during the evaluation. The original report and supporting objective evidence must be provided to the OMT lead. The team leader must provide copies of the report without the supporting evidence to the ACO, MIDO and FSDO managers, AIR-220, AFS-300 and AIR-140. The report should contain:

(1) Cover sheet per appendix 1, figure 16, containing the name of the authorization holder, authorization number, dates of evaluation, and names of the evaluation team and team leader.

(2) Overview of the teams findings and observations about the delegation holder.

(3) Copies of the evaluation discrepancy records and supporting evidence.

(4) Evaluation survey per appendix 1, figure 17.

(5) Recommendations for program improvements, and criteria needing revision.

b. OMT Follow-Up. The OMT should review the evaluation report and verify those discrepancies that require corrective action. Violations of regulations other than the airworthiness standards must be processed in accordance with Order 2150.3. Corrective action must be implemented to address all other discrepancies unless the OMT determines otherwise. See paragraph 3-6 for information on corrective action. The OMT must document the justification for any discrepancies not needing corrective action. The OMT lead should forward the report, with a transmittal letter identifying those discrepancies that require corrective action, to the authorization holder within 15 working days of receiving the report (see appendix 1, figure 18). The OMT lead should send a copy of the transmittal letter to AIR-140.

c. Organization Response. The organization should provide a written response to the transmittal letter and evaluation report within 30 calendar days. The response should contain the organization’s plan for implementing corrective and remedial action for the discrepancies per paragraph 3-6. The authorization holder must implement corrective actions to address the discrepancies identified in the report on a schedule that is agreeable to the OMT lead. The OMT lead ensures that the organization implements all corrective action per paragraph 3-6. The OMT lead may delegate the responsibility to the appropriate OMT members to follow up on issues related to their technical specialty.

d. Dispute Resolution. If the organization disagrees with a discrepancy regarding compliance determinations or methodologies, they may request further review and disposition of the discrepancy. The organization should document the reasons for their disagreement with the discrepancy and forward to the OMT lead. The resolution flow chart in figure 4-1 should be followed to process any disputes that cannot be resolved between the managing offices and the authorization holder. The accountable directorate (for disputes concerning compliance) or appropriate headquarters office (for disputes concerning procedures) has the final authority for determining the appropriateness of the discrepancy. The FAA should provide the organization a decision regarding the disagreement within 30 calendar days.

Par 4-4 Page 17

8/30/05 8100.9A

FIGURE 4-1. EVALUATION COMPLIANCE DISAGREEMENT RESOLUTION FLOW CHART

Organization notified of discrepancy and

supporting rationale

Organization provides documentation on why

the discrepancy is unwarranted

Discrepancy

documented

Documentation sent to appropriate offic

manager (ACO/MIDO/FSDO) for

review

e

Yes

Does office manager concur with discrepancy? No Document decision;

notify OMT, organization and

evaluators

Documentation sent to appropriate directorate or headquarters office for

review

Yes

No

Does office concur with

discrepancy?

Document decision;

notify OMT, organization, and

evaluators

Recommend changes to policy or criteria to

AIR-140 as needed

Corrective action

implemented by organization, verified by

OMT

Par 4-5 Page 18

RESPONSIBILITY. DAS/DOA/SFAR 36 authorized organizations ac › Delegation Administrator and ARs. The authorization holder

8/30/05 8100.9A

CHAPTER 5. DAS/DOA/SFAR 36 QUALIFICATIONS, RESPONSIBILITIES

AND AUTHORITY

5-1. GENERAL. This chapter provides general requirements applicable to organizations seeking a DAS, DOA, or SFAR 36. This chapter also establishes general procedures for obtaining and maintaining a DAS, DOA, or SFAR 36, and describes the general functions and limitations that apply to all authorization holders. The specific requirements for a DAS, DOA, or SFAR 36 are addressed in chapters 6 through 8 of this order, as applicable.

5-2. QUALIFICATIONS. Later paragraphs of this order specify eligibility requirements for each authorization type.

a. The applicant must meet the qualification criteria defined in this paragraph and must also comply with the specific eligibility requirements defined for DAS, DOA, or SFAR 36 in chapters 6 through 8 of this order, as applicable.

b. The FAA may grant authorizations to qualified organizations when:

(1) The organization has sufficient workload applicable to the authorization sought.

(2) There is a benefit to the FAA in granting the authorization, and the FAA has the ability to manage the authorization.

c. The FAA does not issue DOAs, DASs, or SFAR 36s to non-U.S. located applicants. An applicant must meet the appropriate 14 CFR requirements as noted in chapters 6 through 8 of this order and the following qualification criteria in order to be considered for an authorization:

(1) The applicant’s management must have demonstrated integrity in its experience with the FAA and have made a commitment to act with integrity in finding compliance to the regulatory requirements. In addition, the applicant’s proposed administrator and ARs must possess unquestionable integrity, sound judgment, and cooperative attitude.

(2) The organization must employ an authorization holder administrator(s) and employ, or have available, as appropriate for the delegation sought, a staff of ARs who meet the qualification criteria of this order. DAS and SFAR 36 authorization holders must have appropriate staff who meets the requirements of 14 CFR part 21, § 21.439(b) or SFAR 36 paragraph 5b, as applicable.

(3) The organization must have sufficient (as determined by the FAA) resources to perform the level of designation sought. The organization must have a thorough working knowledge, as appropriate to the delegation sought, of the FAA regulations, methods of compliance, policy, and procedures.

(4) The organization must have adequate facilities appropriate to the authorization desired.

(5) The organization must have a successful and recent history of certification work with the FAA.

(6) The organization’s staff must possess integrity, sound judgment and a cooperative attitude toward the FAA.

5-3. RESPONSIBILITY. DAS/DOA/SFAR 36 authorized organizations act as representatives of the Administrator when performing the functions they have been delegated. These authorized organizations and their staffs are guided by the same regulations, directives, policies, guidance and procedures applicable to FAA personnel performing similar functions.

a. Authorization Holder. The authorization holder shall assign an administrator who must ensure that the ARs have sufficient time and resources to maintain cognizance of the regulations, directives, and guidance related to their assigned AR duties and to prepare the necessary reports and related forms separate from other company duties. While discharging the duties of authorization holder, the administrator shall report to a level of management high enough to enable the DOA, DAS, or SFAR 36 to administer duties for the FAA without undue pressure or influence from other organizational segments or individuals. The authorization holder must ensure that the administrator and ARs remain free of any restraints that would limit the DOA’s, DAS’, or SFAR 36’s ability to ensure that authorized functions are performed in compliance with FAA regulations. The authorization holder shall allow the FAA to inspect, evaluate or surveil the facilities, products, parts, components, processes, or appliances, records, and procedures associated with DAS/DOA/SFAR 36.

b. Delegation Administrator and ARs. The authorization holder must ensure that the administrator and ARs act in an independent and impartial manner when exercising their FAA authority. The administrator and ARs must be aware of and avoid potential conflicts of interest between their duties and responsibilities to the

Par 5-1 Page 19

FUNCTIONS NOT DELEGATED. Authorization holders may only be › Approve quality system and procedure manual.

8100.9A 8/30/05

FAA Administrator and their roles as employees of the authorization holder.

5-4. MEMORANDUM OF UNDERSTANDING. Authorization holders must agree to exercise the same care, diligence, judgment, and responsibility when performing the delegated functions as would be exercised by the FAA. This commitment starts at the senior management level of the organization and extends through the proposed ARs. In recognition of this, senior management of the organization and the FAA appointing office(s) will sign a memorandum of understanding (MOU) prepared by the OMT, which outlines the charter, authority, and responsibility of the organization. All management officials in the organization who manage ARs must read and understand the MOU and their responsibilities. The MOU will be signed before appointment. In addition, whenever the signatories of the MOU authorization holder or the lead administrator change, a new MOU must be generated by the OMT and signed by both the organization and the FAA. If the new senior management refuses to sign the MOU, the appointing office shall terminate the authorization. The OMT will recommend any updates of the MOU to the appointing office as appropriate. Appendix 1, figure 6 contains an example of an acceptable MOU.

NOTE: All MOUs must contain a statement setting forth the FAA authority and responsibility to conduct oversight of all delegated activities. In addition, authorization holders must cooperate with the FAA during oversight activities.

5-5. STAFF AUTHORITY AND RESPONSIBILITY.

a. DAS/DOA/SFAR 36 Administrator. The administrator is responsible for the overall management of the authorization and the coordination and completion of their authorized functions. The administrator may be authorized to sign specific documents as specified in the procedure manual. The administrator is responsible for all communication and interface with the OMT. The administrator will communicate with the OMT lead on matters pertaining to FAA interface. The administrator must ensure that the organization is following the procedures prescribed in their procedure manual and that their processes comply with all the requirements of the applicable FAA regulations and policies. An organization may have multiple administrators, however the organization must identify one as the “lead” administrator.

b. Authorized Representatives. Authorized Representatives within the organization have the authority to make findings of compliance, determination of conformity, or airworthiness approvals on behalf of the FAA. The ARs must have sufficient authority within the organizations to make binding decisions to ensure that products meet the applicable regulations, conform to the

type design, and are in condition for safe operation. The procedure manual must identify the ARs and their approval authority.

c. Separation of Duties. DAS, DOA, and SFAR 36 organizations and any designees they may utilize as ARs should be aware that the delegated functions they perform as a DER, DMIR, or DAR are separate and distinct from the functions they perform as an AR of these organizations.

d. Conflict of Interest. It is important that the administrator and ARs and the organization be aware of and avoid potential conflicts of interest between the role of the administrator and AR acting for the FAA and the role as an employee of the authorization holder. The AR, when performing delegated functions for the FAA, must be independent from the organization’s normal engineering and quality control chain of command and report only to the administrator. This should prevent the situation where, for example, the employer asks the AR to use their authorization improperly, or applies pressure on the administrator to compromise their FAA responsibility. It is the organization’s responsibility to prevent such situations. Failure to do so will result in termination of their authorization. Authorization holders must ensure that there are no conflicting constraints placed on the administrator or ARs within the organization.

5-6. FUNCTIONS NOT DELEGATED. Authorization holders may only be delegated the functions allowed by the regulations and this order. Following are examples of functions authorization holders may not perform because they are inherently governmental or the FAA chooses not to delegate them.

a. Issue a TC, amend TC or PC.

b. Make findings of equivalent safety.

c. Grant exemptions.

d. Issue special conditions.

e. Approve or issue airworthiness directives.

f. Make determination of applicable FAA regulations for the certification basis.

g. Establish a means of compliance not previously accepted by the FAA.

h. Make findings reserved by the FAA.

i. Conduct surveillance and oversight.

j. Approve quality system and procedure manual.

Page 20 Par 5-3

AR Qualification Requirements. DOA authorization holders mu › Qualification Requirements for DASs and DOAs Making Findings

8/30/05 8100.9A

5-7. STAFF QUALIFICATION REQUIREMENTS.

a. DAS/DOA/SFAR 36 Administrator. Each DOA, DAS, and SFAR 36 must employ an administrator(s) who serves as the focal point for the FAA coordination. The administrator(s) is responsible for managing the DOA, DAS, or SFAR 36 activities and communicating with the OMT. Therefore, the administrator(s) must have not only the technical experience associated with the type of authorization, but also a broad range of management experience that will enable the administrator(s) to effectively manage all aspects of the designation. Although not required, the administrator may also be an AR. These qualifications must be presented in a resume, which clearly demonstrates the qualification criteria have been met. Prior to FAA approval it must be shown that the administrator(s) has the proper level of responsibility, authority, and ability to assure compliance with approved procedures. The following are the minimum requirements for an administrator:

(1) Minimum of five (5) years of experience working with the FAA on projects similar to those being performed under the authorization. This working experience must include various levels of technical airworthiness responsibilities and experience (e.g., compliance engineer, quality assurance inspector, manufacturing inspector, airworthiness inspector, etc.) as well as management experience in the technical disciplines (for example, engineering, manufacturing, airworthiness, etc.). The collective technical, certification processes, and management experience of the administrator(s) must pertain to the type of authorization sought.

(2) Comprehensive knowledge of FAA policies, procedures and regulations associated with the authorization.

(3) Demonstrated sound judgment, integrity, and cooperative attitude toward the FAA.

(4) Possess sufficient technical knowledge, training, skill, and experience applicable to the type of authorization sought.

b. AR Qualification Requirements. DOA authorization holders must employ a staff of ARs who can make findings on behalf of the FAA. DAS and SFAR 36 holders must employ or have available a staff of ARs who can make findings on behalf of the FAA. ARs are not required to be a DER, DMIR, or DAR.

(1) Engineering and Flight Test ARs. Engineering and flight test ARs making findings of compliance to the airworthiness standards must meet the requirements for Designated Engineering Representative (DER) appointment defined in Order 8100.8, Designee Management Handbook, as appropriate to the functions

authorized. However, the requirement to have significant working experience in a direct working relationship with the FAA may be satisfied by having significant working experience within the authorization holder’s organization.

(2) Inspection ARs. Inspection ARs performing authorized functions must meet the specific qualification criteria for similar function(s) as is described in Order 8100.8 (for example, conformity, export, issuance of airworthiness certificates, etc.). However, the requirement to have significant working experience in a direct working relationship with the FAA may be satisfied by having significant working experience within the authorization holder’s organization.

(3) Use of Existing Designees. Proposing the use of existing designees (i.e., DER, DAR, and DMIR) as ARs to perform similar functions should decrease the time and effort required for the FAA to verify qualifications and approve authorized functions.

(4) Expanding the AR Authority of Existing Designees. Both the applicant and the FAA personnel involved should ensure that if the approval authority desired for an AR exceeds the authority already authorized under their existing delegation, or adds functions, or areas, not currently approved, the organization must determine and the evaluating FAA personnel must verify that the individual is qualified to the same criteria found in Order 8100.8 for the additional areas or functions.

(5) AR Trainees. If a proposed AR meets all the requirements except for direct experience working with the FAA or within the organization, the organization may designate the proposed AR as an “AR Trainee.” Upon approval as an AR trainee, the organization will provide working arrangements to allow the trainee time to prove his or her ability to the authorization holder. The procedure manual must include a process for trainee development if trainees are utilized. For example, review of the trainee’s work by other ARs, or direct supervision of the trainee’s findings by the FAA. AR trainees may not make findings that are not subsequently verified by either a staff AR or the FAA. Trainees may only review data and do not have final approval authority.

(6) Qualification Requirements for DASs and DOAs Making Findings to Foreign Requirements. The OMT may authorize DAS and DOA authorization holders to determine compliance with foreign regulations in support of TC or STC validation programs. The ARs authorized to do so must thoroughly understand the foreign requirements and be knowledgeable of their application. This typically will be evidenced by participation on previous validation programs with the foreign authority and the FAA. The procedure manual shall identify, for each AR, the foreign requirements to which the AR is authorized to make findings.

Par 5-7 Page 21

TRAINING. › Company-Provided Training. DAS, DOA, and SFAR 36 organizati

8100.9A 8/30/05

5-8. PROCEDURE MANUAL. Each authorized organization must perform all authorized functions in accordance with their FAA-approved procedure manual. Procedure manuals must follow the format of appendix 2 and address the applicable detailed requirements provided in chapters 6 though 8. The procedure manual and revisions are to be coordinated with the appropriate disciplines (such as flight test, quality, engineering, etc.) within the DOA/DAS/SFAR 36 organization prior to submittal to the FAA.

a. Content. In addition to the requirements in chapters 6 through 8 of this order, the procedure manual must contain the following:

(1) Cover page with signature blocks for the FAA and authorization holder’s administrator.

(2) Table of Contents.

(3) Log of Revisions.

(4) List of Effective Pages (may be optional if manual is reprinted and paginated at each revision).

(5) Description of how to process changes to the manual.

(6) Limitations of the authorization. DAS and SFAR 36 procedure manuals must specifically identify the models of products and types of projects authorized.

(7) Description of the authorization holder’s facilities (DAS and SFAR 36 only).

(8) Listing of ARs and their authorized functions and forms authorized to sign. The procedure manual must include the name(s), signature(s), impression of stamps (where appropriate), and responsibilities of the individual ARs performing FAA functions and identify the functional areas and limitations for the ARs in accordance with Order 8100.8. See appendix 2 for sample.

NOTE: Signatures, as shown in appendix D of appendix 2 of this order, may be maintained in a separate documented file.

NOTE: If stamps are utilized, the organization must have a stamp control system identified in the manual.

(9) Description of the procedures used in performing authorized functions.

(10) A sample of the forms to be used to indicate inspection acceptance or findings of compliance. FAA forms must be used wherever applicable. Execution instructions must be provided if using other than FAA forms.

(11) Selection criteria for appointing ARs and procedures for expansion of AR’s authority which includes

the process for AR trainee development, if trainees are utilized.

(12) Records required to be kept by the regulations and this order. See chapters 6 though 8 for specific record files.

(13) Description of the training courses that are to be required of each AR and where the AR will acquire the training. Include both standardization and recurrent training per paragraph 5-9.

(14) Process for revising the procedure manual and obtaining FAA approval for revisions.

(15) Changes requiring approval will be defined in the procedure manual.

(16) Prior to approval of these changes, the organization may continue to perform only those functions not affected by the change.

(17) Self-evaluation procedures.

b. Approval. The FAA must review and approve the procedure manual prior to the organization performing any authorized functions. The procedure manual must include the name(s), signature(s), and responsibilities of the administrator(s).

c. Changes. Changes requiring revision to the procedure manual (such as personnel changes) must be clearly identified (e.g., revision bars, highlighting, etc.), submitted to, and approved by the FAA. The authorization holder may not place submitted changes into effect, including changes to ARs or procedures, until approval of the changes is received.

d. FAA Policy or Regulatory Changes. In situations where a procedure manual has not been updated to the latest FAA policy or regulation, FAA policy or regulation takes precedence. The procedure manual must be updated within 120 calendar days of the issue date of the policy or regulation change.

5-9. TRAINING.

a. Company-Provided Training. DAS, DOA, and SFAR 36 organizations must provide training to staff members to ensure continued compliance with the approved procedure manual and the regulations. Training is required upon approval for ARs, with recurrent training at least every two years. The OMT must evaluate and concur with the training material. If the training is presented in a classroom format, the organization must allow FAA attendance at the training session, if requested. The training should consist of at least:

Page 22 Par 5-8

Self-Disclosure. The FAA will not ordinarily seek to impose › The apparent violation does not indicate a lack of or reason

8/30/05 8100.9A

(1) Review of the functions delegated to the authorization.

(2) Review of the organization’s processes and procedure manual.

(3) Review of the AR’s authority and responsibility when performing authorized functions.

(4) Review of FAA policy and guidance material.

(5) Review of representative documentation completed by the authorization holder.

(6) DAS training must also address the need to consider the product manufacturer’s design philosophy, principles, the operational assumptions of the manufacturer, and actual operator procedures during the approval of alterations. The training should also address possible methods to obtain this information for projects accomplished by the DAS.

b. FAA Seminars. In addition to the training attended within the company, ARs must also attend FAAsponsored seminars. FAA seminar schedules are available via the internet at the designee web site.

(1) DAS, DOA, and SFAR 36 administrators must attend FAA-hosted delegation workshops upon appointment as an administrator, and every two years thereafter. These workshops will usually be held annually to discuss issues of interest to authorization holders and obtain their feedback on the effectiveness of the FAA’s delegation program. They must also attend FAA seminars according to paragraph (2) below if they have authority as an AR.

(2) ARs must attend FAA provided seminars as required of designees performing similar functions in accordance with Order 8100.8 and Order 8110.37, Designated Engineering Representative (DER) Guidance Handbook.

c. Training Records. DOA/DAS/SFAR 36 organizations must maintain records of AR’s attendance at company and FAA training.

5-10. DURATION OF APPOINTMENTS. Authorization as a DAS or DOA is effective until surrendered or until the FAA suspends, revokes, or terminates the authorization. Authorization as a SFAR 36 is effective until the termination date of SFAR 36, unless otherwise surrendered, suspended, revoked, or terminated. Authorization holders must notify the OMT within 48 hours of any change (including personnel changes) that could affect the ability of the holder to meet eligibility requirements.

a. Changes in ownership of the organization which result only in a name change with no change in organizational structure, etc., may be executed by reissuing the authorization letter and MOU, along with revising the procedure manual to reflect the new name.

b. Changes within the DAS, DOA, or SFAR 36 involving personnel or structure within the organization or major changes to the organization may require the holder to surrender its authorization and submit a new application. Authorization holders should notify the OMT prior to any planned changes to determine how such changes will be handled.

5-11. SELF-EVALUATION. The organization must perform periodic audits that re-validate the personnel and procedures used within the authorization holder’s organization as approved within their procedure manual. Authorization holders must perform these audits at least annually. The procedure manual must also identify the general audit procedures and frequency as agreed to by the OMT. Self-evaluations do not replace the FAA evaluations detailed in chapter 4.

a. Personnel Evaluation. The self-evaluation must evaluate the ARs using the processes and oversight criteria contained in Order 8110.37 and 8100.8, as appropriate. The DOA/DAS/SFAR36 organization should review individual AR’s project work for accuracy. Frequency of such evaluation should be based on the experience of the AR, the quality of work performed on previous projects, and as established in the procedure manual.

b. Certification Process Evaluation. The selfevaluation must include each element of the procedure manual, such as inspection of design and/or repaired articles to ensure conformity to type design; technical data evaluation; and compliance with the airworthiness standards, etc.

c. Evaluation Records. The organization must maintain records of the self-evaluation and provide copies to the OMT within 7 calendar days of completion.

d. Self-Disclosure. The FAA will not ordinarily seek to impose a civil penalty for regulatory violations on an authorization holder if:

(1) The holder immediately notified the FAA of the apparent violation after detecting it and before the FAA learned of it;

(2) The apparent violation must have been inadvertent;

(3) The apparent violation does not indicate a lack of or reasonable question of basic qualification of the authorization holder;

Par 5-9 Page 23

DAS/DOA/SFAR 36 QUALIFICATIONS, RESPONSIBILITIES AND AUTHORI › MANUFACTURING WORK ACTIVITY. DAS and DOA authorization hold

8100.9A 8/30/05

(4) Immediate action must have been taken, or begun to have been taken, upon discovery to terminate the conduct that resulted in the apparent violation;

(5) The authorization holder must develop and implement a comprehensive corrective action satisfactory to the FAA.

NOTE: Ordinarily, the FAA will not forego legal enforcement action if the authorization holder informs the FAA of the apparent violation during routine FAA investigations/inspections (that time from which the inspection team physically arrives on site until the time the team departs at the completion of the inspection) or in association with accidents and incidents. (See Order 2150.3 and AC 00-58 for more guidance on self-disclosure reporting.)

5-12. MANUFACTURING WORK ACTIVITY. DAS and DOA authorization holders must document their manufacturing work activity on the Summary Activity Report, as described in Order 1380.48, Manufacturing Inspection Management Information System. The organization’s report must be submitted on a frequency as prescribed in the procedure manual. A sample Summary Activity Report is found in appendix 1, figure 12.

Page 24 Par 5-11

DAS Responsibilities. The DAS must investigate and recommen › STC Data Files. The DAS must maintain and make available th

8/30/05 8100.9A

CHAPTER 6. DESIGNATED ALTERATION STATIONS

6-1. GENERAL. This chapter provides information and guidance concerning the authority and procedures of Designated Alteration Stations (DAS).

a. Eligibility. Each DAS is required by 14 CFR § 21.439(a) to be either a domestic repair station under the provisions of 14 CFR part 145, an air carrier or commercial operator, or a manufacturer of a product for which it has alteration authority under the provisions of 14 CFR § 43.3(j). An applicant must have a demonstrated knowledge of the Supplemental Type Certificate (STC) process and must have been previously granted STCs under standard procedures of 14 CFR part 21.

NOTE: The word “or” was inadvertently not incorporated in 14 CFR § 21.439(a). The preamble to this regulation clearly denotes that the intent of this regulation was to allow any one of the three organizations noted above to apply and be considered for a DAS authorization.

b. DAS Authority. The primary authority of a DAS is the ability to issue STCs in accordance with 14 CFR § 21.431. In support of this, the DAS may issue special airworthiness certificates in the experimental category to show compliance for aircraft that are altered by the DAS. Additionally, the DAS may amend standard airworthiness certificates for those aircraft previously issued experimental certificates that are found to conform with the approved STC and are in a condition for safe operation.

c. Limitations.

(1) A DAS may be authorized to issue STCs only for alterations that the DAS holder is able to perform and return to service at its authorized facility. The DAS may not be given design approval authority for any products not covered by the DAS holder’s authority to alter products. The OMT must limit the DAS’s authority based on the experience and capability the DAS holder has demonstrated. Flight Standards OMT members must ensure that repair station or operator DASs have the appropriate ratings. For example, any installation of radios or instruments that involves alteration of the aircraft requires the repair station to have either an airframe or limited airframe rating. DAS procedure manuals must specify the makes and models of products covered by the authorization, and the types of alterations the DAS is authorized to approve. For example, a procedure manual limitation may include:

(a) Avionic and Electrical System Installations – Boeing 727, 737, and 747 series.

(b) Aircraft Interior Installations – Boeing 727 series.

(2) The OMT may impose any limitations that may be necessary, taking into account the DAS staffing and facilities. For example, the OMT may exclude the authority to approve alterations that require flight test or pilot evaluation if the DAS does not employ, or have available, a qualified flight test pilot. The OMT must limit the DAS’s authority based upon the qualifications and capability of the DAS ARs and authorization holder limitations. Approval of test plans is one area where the OMT may decide to retain authority, requiring them to be submitted for approval by the ACO. The OMT should carefully evaluate the DAS’s capability and experience prior to delegating the approval of test plans to the DAS.

(3) The DAS may not be delegated authority that involves areas reserved for FAA approval. Also the DAS may not approve issue papers or perform regulatory activity. See paragraph 5-6. For example, a DAS must obtain FAA approval of:

(a) Interpretations of the airworthiness standards.

(b) Compliance findings involving the acoustical change requirements of 14 CFR part 36 or the exhaust emissions change requirements of 14 CFR part 34.

(c) The application of equivalent safety provisions applied under the provisions of 14 CFR part 21.

d. DAS Responsibilities. The DAS must investigate and recommend corrective actions in accordance with 14 CFR § 21.477 for those matters identified by the FAA. Additionally, the DAS facility should take an active participation in the review of service difficulties submitted to the company and notify the FAA of any findings that required appropriate corrective action.

(1) STC Data Files. The DAS must maintain and make available the data file as prescribed in 14 CFR § 21.493. All STC technical data files must be sent to the FAA as soon as the authorization is surrendered or terminated. In addition to the data file required by 14 CFR § 21.493, the DAS STC technical data files and amendments thereto must also contain the following:

Par 6-1 Page 25

STC Program Considerations. The DAS authorization granted i › Additional Parties Involvement. Projects that involve numer

8100.9A 8/30/05

(a) Program Notification.

(b) STC Application.

(c) FAA Response to Program Notification.

(d) Equivalent Level of Safety Findings.

(e) Special Conditions.

(f) Exemptions.

(g) Findings of Compliance (FAA Form 8100-9).

(h) Requests for Conformity (FAA Form 8120-10) and Statements of Conformity (FAA Form 8130-9).

(i) Conformity Inspection Record (FAA Form 8100-1).

(j) Authorized Release Certificates (FAA Form 8130-3) issued for conformity.

(k) Certification and conformity plans.

(l) Completed compliance checklist.

(m) Type Inspection Authorization (FAA Form 8110-1).

(n) Supplemental Type Inspection Reports (FAA Form 8110-26).

(o) Instructions for Continued Airworthiness (ICA) and Aircraft Evaluation Group acceptance.

(p) Test plans.

(q) Approval of test and analysis reports.

(r) Flight Manual approval page.

(s) Approval of Airworthiness Limitations Section.

(t) Approval of referenced Master Drawing List.

(u) STC with original signature.

Continue reading ↓ 120 of 387 passages shown