AC 00.2-15 Advisory Circular Checklist and Status of Other FAA Publications
This document is cancelled. It may have been replaced. Check the official source before relying on it.
i
Advisory Circular
Subject: ADVISORY CIRCULAR CHECKLIST and Status of Other FAA Publications
Date: 07/01/04 Initiated By: APF-100
AC No: 00-2.15
1. Purpose. This circular transmits the revised checklist of the Federal Aviation Administration’s (FAA) Advisory Circulars (AC's). It also lists certain other FAA publications sold by the Superintendent of Documents, U.S. Government Printing Office (GPO). This checklist is available via the Internet from the FAA home page. See Appendix 5 for access information.
2. Cancellation. AC 00-2.14 dated Jan. 08, 2003 is canceled.
3. Explanation of the AC system. The FAA issues advisory circulars to inform the aviation public in a systematic way of non-regulatory material. Unless incorporated into a regulation by reference, the contents of an advisory circular are not binding on the public. Advisory circulars are issued in a numbered-subject system corresponding to the subject areas of the Federal Aviation Regulations (FAR) (Title 14, Code of Federal Regulations, Chapter I, Federal Aviation Administration); and Chapter III, Commercial Space Transportation, Federal Aviation Administration, Department of Transportation, Parts 400-450. An AC is issued to provide guidance and information in a designated subject area or to show a method acceptable to the Administrator for complying with a related Federal Aviation Regulation.
4. The Advisory Circular Checklist.
a. General. The checklist is divided into five appendices. Appendix 1 explains the numbering system. Appendix 2 lists cancellations that have occurred since the previous issuance. Appendix 3 gives in numeric sequence the title and issuance date for each circular listed. A brief explanation of the contents is given for each entry. The airplane symbol preceding an AC number indicates that the AC is new or updated since the previous edition. Appendix 4 lists FAA publications sold by GPO. You may order the desired publications by using the forms/blanks provided located in Appendix 5.
b. Omitted numbers. In some series, consecutive numbers may be missing. These numbers were assigned to advisory circulars still in preparation, which will be issued
at a later date or were assigned to advisory circulars that have been canceled.
5. How to order:
a. Free Advisory Circulars (AC's). If no price is given after the AC, it is free. You can expedite the delivery of your order by using the special order blank in Appendix 5 (photocopies are acceptable) or send it by FAX to: 301-386-5394. Distribution personnel will send up to ten copies of any free publication. The issuing office must approve larger quantities. Send your request for 3 or less free copies of the ACs to:
U.S. Department of Transportation Subsequent Distribution Office Ardmore East Business Center 3341 Q 75th Ave. Landover, MD 20785
If you wish to be added to or deleted from an AC mailing list, a “Request For Mailing List Action form” is included in Appendix 5 for your convenience. Complete this form and mail it to:
U.S. Department of Transportation Distribution Requirements Section, M-30 Washington, D.C. 20590
b. Publications for Sale. A list of FAA advisory circulars, directives, and other publications is shown in Appendix 4. These publications are for sale by the Superintendent of Documents, U.S. Government Printing Office (GPO). Orders for mailing to foreign countries should include an additional 40 percent of the listed price to cover handling. C.O.D. orders are not accepted.
c. ACs on the Internet. A number of FAA organizations have made their ACs available on the Internet. These ACs may be found through the FAA home page at: www.faa.gov located under Regulations & Policy, and select Advisory Circulars.
AC 00-2.15 07/01/04
ii
6. Reproduction of Advisory Circulars. Advisory circulars may be reproduced in their entirety or in part without
permission from the Federal Aviation Administration.
Originally Signed by
Bernida Williams
Acting Manager Standards and Information Division, APF-100
Mailing lists for Advisory Circulars are computerized. If errors in mailing occur, please notify the Department of Transportation, Distribution Requirements Section, SVC-121.21, Washington, D.C. 20590.
BE SURE TO ENCLOSE THE MAILING LABEL from the shipment together with the Advisory Circular number(s) so that your listing can be corrected.
07/01/04 AC 00-2.15
iii
Contents
Purpose … i
Cancellation … i
Explanation … i
The AC Checklist … i
How to Order … i
Reproduction of Advisory Circulars … ii
Appendix 1. Advisory Circular Numbering System … 3 pages
Appendix 1. Advisory Circular Numbering System … 3 pages
Appendix 2. Cancellations … 2 pages
Appendix 3. Numerical Section … 55 pages
Appendix 4. FAA Publications for Sale
by the U.S. Government Printing Office (GPO) … 11 pages
U.S. Government Bookstores
GPO International Distributors
Appendix 5. Sample Forms and Internet Access Information: … 3 pages
Appendix 5. Sample Forms and Internet Access Information: … 3 pages
Free Publications Order Blank
Request for Mailing List Action
Internet Access Information
APPENDIX 1 ADVISORY CIRCULAR NUMBERING SYSTEM
The Circular Numbering System 1. General. The advisory circular numbers relate to the FAR subchapter titles and correspond to the Parts, and when appropriate, to the specific sections of the Federal Aviation Regulations. 2. General and specific subject numbers. The subject numbers and related subject areas are as follows: … General Subject Specific Subject Number(1) Number(2) Subject … 00 GENERAL 1 Definitions and Abbreviations 10 PROCEDURAL RULES 11 General Rule-Making Procedures 13 Investigation and Enforcement Pro cedures 20 AIRCRAFT 21 Certification Procedures for Products and Parts 23 Airworthiness Standards: Normal, Utility, and Acrobatic Category Airplanes 25 Airworthiness Standards: Transport Category Airplanes 27 Airworthiness Standards: Normal Category Rotorcraft 29 Airworthiness Standards: Transport Category Rotorcraft 31 Airworthiness Standards: Manned Free Balloons 33 Airworthiness Standards: Aircraft Engines 34 Fuel Venting and Exhaust Emission Requirements for Turbine Engine Powered Airplaness 35 Airworthiness Standards: Propellers 36 Noise Standards: Aircraft Type and Airworthiness Certification 39 Airworthiness Directives 43 Maintenance, Preventive Mainte- nance, Rebuilding and Alteration 45 Identification and Registration Marking 47 Aircraft Registration 49 Recording of Aircraft Titles and Security Documents …
APPENDIX 1 ADVISORY CIRCULAR NUMBERING SYSTEM
General Subject Specific Subject Number(1) Number(2) Subject … 60 AIRMEN 61 Certification: Pilots and Flight Instructors 63 Certification: Flight Crewmembers Other Than Pilots 65 Certification: Airmen Other Than Flight Crewmembers 67 Medical Standards and Certification 70 AIRSPACE 71 Designation of Federal Airways, Area Low Routes, Controlled Airspace,and Reporting Points 73 Special Use Airspace 75 Establishment of Jet Routes and Area High Routes 77 Objects Affecting Navigable Air- space 90 AIR TRAFFIC AND GENERAL OPERATING RULES 91 General Operating and Flight Rules 93 Special Air Traffic Rules and Airport Traffic Patterns 95 IFR Altitudes 97 Standard Instrument Approach Pro- cedures 99 Security Control of Air Traffic 101 Moored Balloons, Kites, Unmanned Rockets and Unmanned Free Balloons 103 Ultralight Vehicles 105 Parachute Jumping 107 Airport Security 108 Airplane Operators Security 109 Indirect Air Carrier Security 119 CERTIFICATION:AIR CARRIERS AND COMMERCIAL OPERATORS 120 AIR CARRIERS, AIR TRAVEL CLUBS, AND OPERATORS FOR COMPENSATION OR HIRE: CERTIFICATION AND OPERATIONS 121 Certification and Operations: Domestic, Flag, and Supplemental
… General Subject Specific Subject Number(1) Number(2) Subject … Air Carriers and Commercial Operators of Large Aircraft 125 Certification and Operations: Air- planes Having a Seating Capacity of 20 or More Passengers or a Maxi- mum Payload Capacity of 6,000 Pounds or More 127 Certification and Operations of Scheduled Air Carriers with Helicopters 129 Operations of Foreign Air Carriers 133 Rotorcraft External-Load Opera- tions 135 Air Taxi Operators and Commercial Operators 137 Agricultural Aircraft Operations 139 Certification and Operations: Land Airports Serving CAB- Certificated Air Carriers 140 SCHOOLS AND OTHER CERTIFICATED AGENCIES 141 Pilot Schools 143 Ground Instructors 145 Repair Stations 147 Aviation Maintenance Technician Schools 150 AIRPORT NOISE COMPATI-- BILITY PLANNING 151 Federal Aid to Airports 152 Airport Aid Program 155 Release of Airport Property from Surplus Property Disposal Restrictions 156 State Block Grant Pilot Program 157 Notice of Construction, Alteration, Activation, and Deactivation of Airports 158 Passenger Facilities Charges 159 National Capital Airports 159/10 Washington National Airport 159/20 Dulles International Airport 161 Notice and Approval of Airport Noise and Access Restrictionsn 169 Expenditures of Federal Funds for Nonmilitary Airports or Air Naviga- tional Facilities Thereon 170 NAVIGATIONAL FACILITIES 170 Establishment and Discontinuance Criteria for Airport Traffic ControlTower Facilities
… General Subject Specific Subject Number(1) Number(2) Subject … 171 Non-Federal Navigation Facilities
180 ADMINISTRATIVE REGULATIONS 183 Representatives of the Administrator 185 Testimony by Employees and Pro- duction of Records in Legal Pro- ceedings 187 Fees 189 Use of Federal Aviation Administra- tion Communication System. 190 WITHHOLDING SECURITY INFORMATION 191 Withholding Security Information from Disclosure Under the Air Transportation Security Act of 1974 198 Aviation Insurance Program 210 FLIGHT INFORMATION 211 Aeronautical Charts and Flight Information Publications 212 Publication Specification: Charts and Publications
400 COMMERCIAL SPACE TRANSPORTATION 440 Financial Responsibility … 1---Based on FAR Subchapter Titles (Excluding the 210 series). 2--Based on FAR Part Titles (Excluding the 210 series). 3. Within the General Subject Number Areas, specific selectivity in advisory circular mail lists is available corresponding to the applicable FAR Parts. For example: under the 60 general subject area, separate mail lists for advisory circulars issued in the 61, 63, 65, or 67 series are available. An AC numbered “60” goes to all numbers in the 60 series. When the volume of circulars in a series warrants a subsubject breakdown, the general number is followed by a slash and a subsubject number. Material in the 150 series, Airports, is issued under the following subsubjects: 150/5000 Airport Planning. 150/5020 Noise Control and Compatibility Planning for Airports. 150/5100 Federal-aid Airport Program. 150/5150 Surplus Airport Property Conveyance Programs. 150/5190 Airport Compliance Program. 150/5200 Airport Safety-General. 150/5210 Airport Safety Operations (Recommended Training, Standards, Manning). 150/5220 Airport Safety Equipment and Facilities.
150/5230 Airport Ground Safety System. 150/5240 Civil Airports Emergency Preparedness. 150/5325 Influence of Aircraft Performance on Aircraft Design. 150/5335 Runway, Taxiway, and Apron Characteristics. 150/5340 Airport Visual Aids. 150/5345 Airport Lighting Equipment. 150/5360 Airport Buildings. 150/5370 Airport Construction. 150/5380 Airport Maintenance. 150/5390 Heliports. 4. Individual circular identification numbers. Each circular has a subject number followed either by a dash and a consecutive number (135-15) or a period with a specific FAR section number, followed by a dash and a consecutive number (135.169-2) identifying the individual circular. This consecutive number is not used again in the same subject series. Revised circulars have a letter A, B, C, etc., after the consecutive number to show complete revisions. Changes to circulars have Chg. 1, Chg. 2, Chg. 3, etc., after the identification number on pages that have been changed. The date on a revised page is changed to the date of the Change transmittal.
07/01/04 AC 00.2-15 Appendix 2
A2-1
APPENDIX 2 CANCELLATIONS
APPENDIX 2 CANCELLATIONS
Cancellations are listed below. The suffix following an AC number indicates a revision to that AC and cancels the previous edition. For example, AC 00-6A replaces and cancels AC 00-6; AC 00-7D replaces and cancels AC 00-7C. ACs may be canceled without replacement, by the issuing office or by another ACs or publication. 00-55 Announcement of availability: FAA Order 8130.21A, Procedures for Completion and Use of FAA Form 8130, Airworthiness Approval Tag (1/19/94) (AIR-200). Cancelled by AIR-200 20-95 Fatigue Evaluation of Rotorcraft Structure (5/18/76) (ASW-100) Sets forth acceptable means, not the only means, of compliance with the provisions of FAR sections 27.571 and 29.571 dealing with the fatigue evaluation of rotorcraft structure.
Replaced by change 1 to AC-1B dated 2/12/2003 20-137 Dynamic Evaluation of Seat Restraint Systems & Occupant Restraint for Rotocraft (Normal and Transport) (3/30/92) (ASW-111) Provides guidance regarding acceptable means but not the only means of compliance with Parts 27 and 29 of the Federal Aviation Regulations (FAR) applicable to dynamic testing of seats intended for use in Normal and Transport Category. Replaced by change 1 to AC 27-1B paragraph 27.562 dated 2/12/2003 and Change 1 to AV 29-2C paragraph 29.562 dated 2/12/2003. 61-23C Pilot’s Handbook of Aeronautical Knowledge (7/10/97) (AFS-630) SN 050-011-00078-0 Replaced by FAA H- 8083-25 Pilot’s Handbook of Aeronautical Knowledge (12/03) (AFS-630). 70-2E Airspace Utilization Considerations in the Proposed Construction, Alteration, Activation & Deactivation of Airports (11/29/95) (AAS-200) Advises persons proposing to construct, activate or deactivate a civil or joint-use (civil/military) airport of the requirements to notify the Federal Aviation Administration of their plan.
It also outlines some of the airspace utilization factors, which should be considered early in the planning stages. By Airport Engineering Division AAS-100. 121.445-1D (11/01/03) Pilot-In-Command Qualifications For Special Areas/Routes And Airports. FAR Section 121.445 (6/20/90) (AFS-220) Provides information for all Part 121 certificate holders concerning those area/routes and airports where the Administrator has determined that special qualifications are required of pilots in command as provided in FAR Section 121.445. Cancelled information contained in handbook bulletin for air transportation 03-07, special pilot in command airport qualification; opspecs paragraph C050. 145.101-1B Applications for Air Agency Certificate--Manufacturer’s Maintenance Facility (11/30/83) (AIR-200) Provided manufacturers with the procedures for obtaining a repair station certificate with a limited rating for a manufacturer (known as a manufacturer’s maintenance facility (MMF). Part 145, effective date January 31, 2004, no longer allows for the issuance of limited repair stations.
150/5000-6 Announcement of Availability--Micro-Paver, Pavement Management System (PMS) (4/16/87) (AAS-200) announces the availability of the Micro-Paver Program, Version 1.0. By Airport Engineering Division (AAS-100). 150/5000-7 Announcement of Availability Report No. DOT/FAA/PP/87-1 Measuring the Regional Economic Significance of Airports (5/12/87) (APP-400) Announces the availability of the report “Measuring the Regional Economic Significance of Airports. Cancelled by Office of Airport Planning and Programming National Planning Division (APP-400). 150/5000-10A Announcement of Availability Report No. DOT/FAA/PP/-92-6, Estimating the Regional Economic Significance of Airports (7/3/93) (APP-400) Announces the availability of subject report. Cancelled by Office of Airport Planning and Programming National Planning Division (APP-400). 150/5000-11 Announcement of Availability All Cargo Carrier Activity Report (FAA Form 5100-108, Revised). (3/3/93) (APP-400) Provides guidance for the submission of FAA Form 5100-108 (revised as of March 1993).
Cancelled by Office of Airport Planning and Programming National Planning Division (APP-400).
07/01/04 AC 00.2-15 Appendix 2
A2-2
150/5070-3 Planning the Airport Industrial Park (9/30/65) (APP-400) Provides guidance to communities, airport boards, and industrial developers for the planning and development of Airport Industrial Parks. Cancelled by Office of Airport Planning and Programming National Planning Division (APP-400). 150/5300-11 Announcement of Availability Report No. FAA-AAS-80-1, National Runway Friction Measurement Program (4/21/81) (AAS-200) Announces the availability of the National Runway Friction Measurement Program Final Report. By Airport Engineering Division (AAS-100). Cancelled by Office of Airport Planning and Programming National Planning Division (APP-400). 150/5360-10 Announcement of Availability--Airport Landslide Simulation Model (ALSIM) (4/24/84) (AAS-3) Announces the availability and describes some of the features of a dynamic simulation computer model for use by airport planners, designers, and operators in evaluating and comparing the effectiveness of alternative airport terminal and landslide configurations and facilities. Cancelled by Office of Airport Safety and Standards FAA-S-8081-19 Recreational Pilot Powered Parachute Practical Test Standard (3/12/97) (AFS-630) Establishes the standard for recreational pilot certification practical tests for the powered parachute category. This standard will become effective when the recommended change to 14 CFR part 61 is approved establishing a recreational pilot certificate for this category. Canceled by AC 61-127A
APPENDIX 3
APPENDIX 3
NUMERICAL LIST OF ADVISORY CIRCULARS
Important Notice
Additions The airplane symbol preceding an AC number identifies new or revised ACs issued since the last edition of this checklist. Revised ACs are identified by a letter of the alphabet following the AC number.
General
NUMERICAL LIST OF ADVISORY CIRCULARS
Subject No. 00
00-1.1 Government Aircraft Operations (4/19/95) (AFS-220) Provides guidance on whether particular government aircraft operations are public aircraft or civil aircraft operations under the new statutory definition of “public aircraft.” This AC contains FAA’s intended application of key terms in the new statutory definition. For operations that have lost public aircraft status under the new law, information is provided on bringing those operations into compliance with FAA safety regulations for civil aircraft and provides information on applying for an exemption. 00-2.14 Advisory Circular Checklist (1/8/03) (APF-100) Transmits the revised checklist of current FAA advisory circulars as of 2002. 00-6A Aviation Weather (3/3/75) (AFS-400) Provides an up-todate and expanded text for pilots and other flight operations personnel whose interest in meteorology is primarily in its application to flying. 00-7D State and Regional Disaster Airlift (SARDA) Planning (9/15/98) (ADA-20)
Provides officials with guidance to access and utilize a broad range of aviation resources within the state, when needed to support civil emergency operations. 00-24B Thunderstorms (1/20/83) (AFS-400) Describes the hazards of thunderstorms to aviation and offers guidance to help prevent accidents caused by thunderstorms. 00-25 Forming and Operating a Flying Club (3/24/69) (AFS-800) Provides preliminary information that will assist anyone or any group of people interested in forming and operating a flying club. 00-30B Atmospheric Turbulence Avoidance 9/9/97 (AFS-400) Describes to pilots, aircrew members, dispatchers, and other operations personnel the various types of clear air turbulence (CAT) and some of the weather patterns associated with it. Also included are “Rules of Thumb” for avoiding or minimizing CAT encounters. 00-31A United States (US). National Aviation Standard for the VOR/DME/TAC Systems (9/20/82) (ANN-130) Informs the aviation community of the establishment and content of the United States (US). National Aviation Standard for the Very High Frequency
Omni directional Radio Range (VOR)/Distance Measuring Equipment (DME)/Tactical Air Navigation (TACAN) Systems. 00-33B Nickel-Cadmium Battery Operational, Maintenance, and Overhaul Practices (7/9/97) (AFS-400) Provides guidelines for more reliable nickel-cadmium battery operation through proper operational and maintenance practices, and has been reissued to include reconditioning information. 00-34A Aircraft Ground Handling and Servicing (7/29/74) (AFS-340) Contains information and guidance for the servicing and ground handling of aircraft. 00-41B FAA Quality Control System Certification Program (10/10/89) (ASU-430) Describes the Federal Aviation Administration (FAA) Quality Control System Certification Program and the mechanics of implementation. It is intended for guidance and information only.
00-45E Aviation Weather Services (12/99) (AFS-400) Supplements AC 00-6A, Aviation Weather, in that it explains the weather service in general and the use and interpretation of reports, forecasts, weather maps, and prognostic charts in detail. SN 050-007-01329-9 00-46D Aviation Safety Reporting Program (2/26/97) (ASY-300) Describes the Federal Aviation Administration’s Aviation Safety Reporting program, which utilizes the National Aeronautics and Space Administration (NASA) as a third party to receive and analyze Aviation Safety Reports. This cooperative safety reporting program invites users of the National Aviation System to report to NASA actual or potential discrepancies and deficiencies involving the safety of aviation operations. 00-54 Pilot Windshear Guide (11/25/88) (AFS-200) Communicates key windshear information relevant to flight crews. Appendix 1 of this advisory circular is the Pilot Windshear Guide, which is only one section of the two-volume Windshear Training Aid. 00-56A Voluntary Industry Distributor Accreditation Program (6/13/02) (AFS-300) Describes a system for the voluntary accreditation of civil aircraft parts distributors on the basis of voluntary industry oversight and provides information that may be used for developing accreditation programs. The FAA believes such programs will assist in alleviating lack of documentation and will improve traceability.
00-57 Hazardous Mountain Winds and Their Visual Indicators (9/10/97) (AND-720) Assists pilots involved in aviation operations to diagnose the potential for severe wind events in the vicinity of mountainous areas. It provides information on preflight planning techniques and on in-flight evaluation strategies for avoiding destructive turbulence and loss of aircraft control. Pilots, dispatchers, air traffic controllers, and other who must deal with weather phenomena and the routing of aircraft will benefit from the information contained in this advisory circular. 00-58 Voluntary Disclosure Reporting Program (5/4/98) (AFS-350) Replaces AC 120-56. Provides information and guidance that may be used by certificate holders, production approval holders, indirect air carriers, and foreign air carriers disclosing apparent violations to the FAA of regulations in 14 CFR parts 21, 107, 108, 109, 121, 125, 129 (security program violations only), 133, 135, 137, 141, 142, 145, & 147 under the self-disclosure program. The procedures outlined in this AC can be applied to all of the above. The procedures and practices outlined in this AC cannot be applied to those who are required to report failures, malfunctions and defects under 14 CFR part 21.3 and do not make those reports in the timeframe required by the regulation. 00-59 Integrating Helicopter and Tiltrotor Assets Into Disaster Relief Planning (11/98) (AND-710) Provides guidance to state and local emergency relief planners on integrating helicopters and tiltrotor aircraft into disaster relief planning efforts.
00-60 North American Free Trade Agreement and Specialty AIR Services Operations (11/9/99) AFS-805) Provides information for aircraft operators from the United States who plan to conduct specialty air services (SAS) operations in Canada or Mexico in accordance with the North American Free Trade Agreement. It also provides information for aircraft operators from Canada or Mexico who plan to conduct SAS operations in the U.S. SN 050-007-01281-1 00-61 Event Planning Guide (7/24/00) (AFS-800) Describes acceptable methods for organizing the aviation community for all events, such as major sports events (auto racing, golf, etc.) It is not limited to sporting events, but can be used whenever there is a large amount of aviation activity on an infrequent basis and open gatherings of people. The goal of this AC is to enhance air and ground safety. This AC does not include events that require FAA Form, 7711-1, Application for Certificate of Waiver or Authorization. 00-62 Internet Communications (ARS-100) (10/02) This AC describes the process for any person or organization that provides access to aviation weather and notices to Airmen (NOTAMS) via the public Internet to become a qualified Internet communications provider (QICP)
Procedural Subject
No. 10
11-2A Notice of Proposed Rulemaking Distribution System (7/26/84) (ABC-100) Provides the public with information relative to participation in the FAA rulemaking process and explains the availability of the Notices. 13-1 Aviation Safety Inspector Work Site Access (12/28/95) (AFS-120/AFS-300) Explains the requirement and use of FAA Form 8000-39, Aviation Safety Inspector Identification Card, and its relation to the Aviation Safety Credential, FAA Form 110A. This AC is issued primarily to acquaint airport authorities and the airport security personnel with the FAA Form 8000-39 and the aviation safety inspector’s need to be in restricted areas of the airport to perform official FAA business.
Aircraft
Subject No. 20
20-18A Qualification Testing of Turbo-jet Engine Thrust Reversers (3/16/66) (ANE- 100) Discusses the requirements for the qualification of thrust reversers and sets forth an acceptable means of compliance with the tests prescribed in Federal Aviation Regulations, Part 33, then run under nonstandard ambient air conditions. 20-24B Qualification of Fuels, Lubricants, and Additives (12/20/85) (ANE-110) Provides acceptable procedures for approving the qualification of fuels,
lubricants, and additives for use in certificated aircraft engines. 20-27E Certification and Operation of Amateur-Built Aircraft (9/26/01) (AIR-200) Provides guidance and information relative to the airworthiness certification and operation of amateurbuilt aircraft. 20-29B Use of Aircraft Fuel Anti-icing Additives (1/18/72) (ANE-100) Provides information on the use of anti-icing additives PFA-55MB and Mil-I-27686 as an acceptable means of compliance with the FARs that require assurance of continuous fuel flow under conditions where ice may occur in turbine aircraft fuel systems. 20-30B Aircraft Position Light and Anticollision Light Installation (7/20/81) (AIR- 120) Sets forth acceptable means, but not the only means, of showing compliance with the Federal Aviation Regulations (FAR) applicable to installed position lights and anticollision lights. 20-32B Carbon Monoxide (CO) Contamination in Aircraft-- Detection and Prevention (11/24/72) (ACE-110) Provides information on the potential dangers of carbon monoxide contamination from faulty engine exhaust systems or cabin heaters of the exhaust gas heat exchanger type. 20-33B Technical Information Regarding Civil Aeronautics Manuals 1, 3, 4a,4b, 5, 6, 7, 8, 9, 13 and 14 (5/1/75) (AIR-100) Advises the public that policy information contained in the subject Civil Aeronautics Manuals may be used in conjunction with specific
sections of the Federal Aviation Regulations. 20-34D Prevention of Retractable Landing Gear Failures (8/8/80) (AFS-340) Updates statistical information related to landing accidents involving aircraft with retractable landing gear and suggests procedures to minimize those accidents. 20-35C Tie-Down Sense (7/12/83) (AFS-340) Provides updated information of general use on aircraft tie down techniques and procedures. 20-36S Index of Articles (Materials, Parts, Processes and Appliances) Certified Under the Technical Standard Order System (AFS-610) AC canceled 11/99. Available in Access database as TSOA listing at http://av-info.faa.gov 20-37D Aircraft Metal Propeller Maintenance (8/15/89) (AFS-340) Provides information and suggested procedures to increase service life and to minimize blade failures of metal propellers. 20-38A Measurement of Cabin Interior Emergency Illumination in Transport Airplanes (2/8/66) (ANM- 100) Outlines acceptable methods, but not the only methods, for measuring cabin interior emergency illumination on transport airplanes, and provides information as to suitable measuring instruments.
20-40 Placards for Battery-Excited Alternators Installed in Light Aircraft (8/11/65) (ACE-100) Sets forth an acceptable means of complying with placarding rules in Federal Aviation Regulations 23 and 27 with respect to battery excited alternator installations. 20-41A Substitute Technical Standard Order (TSO) Aircraft Equipment (4/5/77) (AIR- 120) Sets forth an acceptable means for complying with rules governing aircraft equipment installations in cases involving the substitution of technical standard order equipment for functionally similar TSO approved equipment. 20-42C Hand Fire Extinguishers for use in Aircraft (3/7/84) (ACE-110) Provides methods acceptable to the Administrator for showing compliance with the hand fire extinguisher provisions in Parts 25, 29, 91, 121, 125, 127, and 135 of the FAR and provides updated general information. 20-43C Aircraft Fuel Control (10/20/76) (AFS-340) Alerts the aviation community to the potential hazards of inadvertent mixing or contamination of turbine and piston fuels, and provides recommended fuel control and servicing procedures. 20-44 Glass Fiber Fabric for Aircraft Covering (9/3/65) (ACE-100) Provides a means, but not the sole means, for acceptance of glass fiber fabric for external covering of aircraft structure.
20-45 Safetying of Turnbuckles on Civil Aircraft (9/17/65) (ACE-100) Provides information on turnbuckle safetying methods that have been found acceptable by the FAA during past aircraft type certification programs. 20-47 Exterior Colored Band Around Exits on Transport Airplanes (2/8/66) (ANM-100) Sets forth an acceptable means, but not the only means, of complying with the requirement for a 2-inch colored band outlining exits required to be openable from the outside on transport airplanes. 20-48 Practice Guide for Decontaminating Aircraft (5/5/66) (AFS-330) The title is self-explanatory. 20-52 Maintenance Inspection Notes for Douglas DC-6/7 Series Aircraft (Consolidated Reprint. Includes Change 1). (8/24/67) (AFS-310) Describes maintenance inspection notes which can be used for the maintenance support of certain structural parts of DC-6/7 series aircraft. 20-53A Protection of Aircraft Fuel Systems Against Fuel Vapor Ignition Due to Lightning (4/12/85) (ACE-111) Provides information and guidance concerning an acceptable means, but not the only means, of compliance with Parts 23 or 25 of the Federal Aviation Regulations (FAR) applicable to preventing ignition of fuel vapors due to lightning. 20-56A Marking of TSO-C72b Individual Flotation Devices (4/1/75) (AIR-120)
Outlines acceptable methods for marking individual flotation devices which also serve as seat cushions. 20-57A Automatic Landing Systems (ALS) (1/12/71) (ANM-110) Sets forth an acceptable means of compliance, but not the only means, for the installation approval of automatic landing systems in transport category aircraft, which may be used initially in Category II operations. Approval of these aircraft for use under such conditions will permit the accumulation of data for systems, which may be approved for Category IIIa in the future. 20-59 Maintenance Inspection Notes for Convair 240, 340/440, 240T, and 340T Series Aircraft (2/19/69) (AFS-330) Describes maintenance inspection notes which can be used for the maintenance support of certain structural parts of Convair 240, 340/440, 240T, and 340T series aircraft. 20-59, Chg. 1 (8/24/72) Provides additional material for Convair Models 240 and 600/240D; Models 340/440 and 640/340D/440D series aircraft maintenance inspection programs. 20-60 Accessibility to Excess Emergency Exits (7/18/68) (ANM-110A) Sets forth acceptable means of compliance with the “readily accessible” revisions in the Federal Aviation Regulations dealing with excess emergency exits.
20-62D Eligibility, Quality, and Identification of Aeronautical Replacement Parts (5/24/96) (AFS-340) Provides information and guidance for use in determining the quality, eligibility and traceability of aeronautical parts and materials intended for installation on U.S. typecertificated products and to enable compliance with the applicable regulations. 20-64 Maintenance Inspection Notes for Lockheed L-188 Series Aircraft (8/1/69) (AIR- 3) Describes maintenance inspection notes, which can be used for the maintenance support of certain structural parts of Lockheed L-188 series aircraft. 20-64, Chg. 1 (10/26/73) 20-65 U.S. Airworthiness Certificates and Authorizations for Operation of Domestic and Foreign Aircraft (8/11/69) (AIR-200) Provides general information and guidance concerning issuance of airworthiness certificates for U.S. registered aircraft, and issuance of special flight authorizations for operation in the United States of foreign aircraft not having standard airworthiness certificates issued by the country of registry. 20-66A Vibration Evaluation of Aircraft Propellers (9/17/01) (ANE-100) Outlines acceptable means, but not the sole means, for showing compliance with the requirements of the FARs concerning propeller vibration. 20-67B Airborne VHF Communications Equipment Installations (1/16/86) (AIR-120)
Sets forth one means, but not the only means, of demonstrating compliance with the airworthiness rules governing the functioning of airborne VHF communications equipment. 20-68B Recommended Radiation Safety Precautions for Ground Operation of Airborne Weather Radar (8/8/80) (AFS-600) Sets forth recommended radiation safety precautions for ground operation of airborne weather radar. 20-69 Conspicuity of Aircraft Instrument Malfunction Indicators (5/14/70) (AIR-120) Provides design guidance information on methods of improving conspicuity of malfunction indication devices. 20-71 Dual Locking Devices on Fasteners (12/8/70) (AIR-120) Provides guidance and acceptable means, not the sole means, by which compliance may be shown with the requirements for dual locking devices on removable fasteners installed in rotorcraft and transport category airplanes. 20-73 Aircraft Ice Protection (4/21/71) (AIR-120) Provides information relating to the substantiation of ice protection systems on aircraft. 20-74 Aircraft Position and Anti-collision Light Measurements (7/29/71) (AIR-120) Contains useful information concerning measurements for intensity, covering, and color of aircraft position and anti-collision lights. 20-76 Maintenance Inspection Notes for Boeing B-707/720 Series Aircraft (10/21/71) (AFS-330)
Provides maintenance inspection notes which can be used for the maintenance support program for certain structural parts of the B-707/720 series aircraft. 20-77 Use of Manufacturers’ Maintenance Manuals (3/22/72) (AFS-340) Informs owners and operators about the usefulness of manufacturers’ maintenance manuals for servicing, repairing, and maintaining aircraft, engines and propellers. 20-78 Maintenance Inspection Notes for McDonnell Douglas DC-8 Series Aircraft (7/11/72) (AFS-330) Provides maintenance inspection notes which can be used for the maintenance support program for certain structural parts of the DC-8 series aircraft. 20-82 Maintenance Inspection Notes for Fairchild Hiller F-27/FH-227 Series aircraft (Includes Change 1) (12/5/72) (AFS-330) Provides maintenance inspection notes which can be used for the maintenance support program for certain structural parts of Fairchild Hiller F-27/FH-227 series aircraft. 20-83 Maintenance Inspection Notes for Boeing B-737 Series Aircraft (Includes Changes 1 and 2) (1/17/73) (AFS- 330) Provides maintenance inspection notes, which can be used for the maintenance support program for certain structural parts of the B-737 series aircraft. 20-84 Maintenance Inspection Notes for Boeing B-727 Series Aircraft. (1/22/73) (AFS-300) Provides inspection notes which can be used for the maintenance support program for certain structural parts of the B-727 series aircraft.
20-84, Chg. 1 (8/8/74) Updates material for the B-727 series aircraft maintenance inspection program. Inspection of selected areas of the wing, fuselage, empennage and landing gear of the B-727 series aircraft are presented supplementing information currently available in AC 20-84. 20-84, Chg. 2 (1/31/75) 20-88A Guidelines on the Marking of Aircraft Powerplant Instruments (Displays) (9/30/85) (ANM- 112) Provides revised guidelines on the marking of aircraft powerplant instruments and electronic displays (cathode ray tubes, etc.). These guidelines offer acceptable, but not exclusive, methods of compliance with the powerplant instrument color marking requirements. 20-94 Digital Clock Installation in Aircraft (3/4/76) (AFS-350) Provides guidelines for operating and installing digital clocks in aircraft. 20-96 Surplus Military Aircraft: A Briefing for Prospective Buyers (12/2/76) (AIR- 200) Provides many answers to questions regarding the purchasing of surplus military aircraft (type certification, is the aircraft flyable, is it sold for spare parts, scrap?). 20-97A High-Speed Tire Maintenance and Operational Practices (5/13/87) (AFS-340) Provides information and guidance for maintaining aircraft tires to ensure their continued airworthiness. 20-99 Anti-skid and Associated Systems (5/27/77) (ANM-100)
Provides an acceptable means, but not the only means, of complying with the requirement that anti-skid and associated systems must be designed so that no probable malfunction will result in a hazardous loss of braking or directional control of an airplane. 20-100 General Guidelines for Measuring Fire-Extinguishing Agent Concentrations in Powerplant Compartments (9/21/77) (AIR-120) Describes the installation and use of a model GA-2A fire extinguisher agent concentration recorder in determining the distribution and concentration of fire-extinguishing agents when discharged in an aircraft powerplant compartment. 20-101C Airworthiness Approval of Omega/VLF Navigation Systems for Use in the United States NAS and Alaska (9/12/88) (ACE-130W/AIR-120) Presents an acceptable means of compliance, but not the only means, for the approval of Omega and Omega/Very Low Frequency (VLF) Navigation Airborne Equipment as a means of Visual Flight Rules (VFR)/Instrument Flight Rules (IFR)/Area Navigation (RNAV) en route navigation within the conterminous United States and Alaska. 20-103 Aircraft Engine Crankshaft Failure (3/7/78) (AFS-340) Provides information and suggests procedures to increase crankshaft service life and to minimize failures. 20-104 Revised Powerplant Engineering Report No. 3, Standard Fire Test Apparatus and Procedure (for Flexible Hose Assemblies) (4/12/78) (AIR-120) Announces the availability of the subject report.
20-105B Reciprocating Engine Power-loss Accident Prevention and Trend Monitoring (6/15/98) (AFS-340) Updates statistical information and brings to the attention of aircraft owners, operators, manufacturers, and maintenance personnel the circumstances surrounding engine power-loss accidents with recommendations on how those accidents can be prevented. 20-106 Aircraft Inspection for the General Aviation Aircraft Owner (4/1/78) (AFS- 340) Describes techniques used in aircraft inspections. Designed to familiarize owner, pilots, student mechanics, and others with inspection procedures, it does NOT qualify an individual to make airworthiness determinations. 20-107A Composite Aircraft Structure (4/25/84) (AIR-103) Sets forth an acceptable, but not the only, means of showing compliance with the provisions of FAR Parts 23, 25, 27, and 29 regarding airworthiness type certification requirements of composite aircraft structures involving fiber reinforced materials, e.g., carbon (graphite), boron, aramid (kevlar), and glass reinforced plastics. Guidance information is also presented on associated quality control and repair aspects. 20-109A Service Difficulty Program (General Aviation) (4/8/93) (AFS-620) Describes the Service Difficulty Program as it applies to general aviation activities. Instructions for completion of the revised FAA Form 8010-4 (10-92), Malfunction or Defect Report, are provided.
20-110L Index of Aviation Technical Standard Orders (10/10/00) (AIR-120) Describes the public procedure the Federal Aviation Administration (FAA) will use to develop and issue Technical Standard Orders (TSOs) for aeronautical articles to be used on civil aircraft. Presents an index of the FAA TSOs, which contain minimum performance standards for specific materials, parts processes, and appliances used in civil aircraft. 20-111 Communication Caused By Unintentional Keyed Microphones (10/10/80) (AFS- 350) Alerts the aviation community to the potential hazards created by unintentional keying of microphones resulting in radio transmissions from airborne, mobile, and ground based radio transmitters and gives guidance on alleviating ensuing hazards. 20-112 Airworthiness and Operational Approval of Airborne Systems to be Used In Lieu of Ground Proximity Warning System (GWPS) (2/19/81) (AIR-120) Provides information and guidance regarding airworthiness and operational approval of airborne equipment/systems in accordance with FAR 135.153(b) and (c). 20-113 Pilot Precautions and Procedures to be taken in Preventing Aircraft Reciprocating Engine Induction System & Fuel System Icing Problems (10/22/81) (ACE-100) Provides information pertaining to aircraft engine induction system icing and the use of fuel additives to reduce the hazards of aircraft operation that may result from the presence of water and ice in aviation gasoline and aircraft fuel systems.
20-114 Manufacturers’ Service Documents (10/22/81) (AIR-100) Suggests acceptable methods by which product manufacturers may indicate FAA approval of recommended actions prescribed in manufacturers’ service documents. 20-115B Radio Technical Commission for Aeronautics, Inc. Document RTCA/DO-178B (1/11/93) (AIR-130) Calls attention to RTCA, Inc., (formerly the Radio Technical Commission for Aeronautics) Document RTCA/DO- 178B, “Software Considerations in Airborne Systems and Equipment Certification,” issued December 1992. It discusses how the document may be applied with FAA technical standard order (TSO), authorizations, type certification (TC), or supplemental type certification authorization (STC). 20-116 Marking Aircraft Fuel Filler Openings With Color Coded Decals (9/17/82) (ACE- 100) Discusses the conditions under which color coded decals may be used to comply with the requirements in FAR Parts 23, 25, 27, and 29 for marking fuel filler openings. 20-117 Hazards Following Ground Deicing and Ground Operations in Conditions Conducive to Aircraft Icing (12/17/82) (AFS-200) Provides information on the identified hazards associated with ground deicing and ground operations in conditions conducive to aircraft icing. 20-117, Chg. 1 (4/15/83) Corrects an error in Figure 3-2, Appendix 3, regarding the values of “TIME TO CRYSTALLIZATION (MIN).”
20-118A Emergency Evacuation Demonstration (3/9/87) (ACE-100) Sets forth acceptable means, but not the only means, of showing compliance with the Federal Aviation Regulations (FAR) applicable to required emergency evacuation demonstrations from airplanes certified to the requirements of SFAR 23, SFAR 41, Appendix A of Part 135, or Part 23, commuter category. 20-119 Fuel Drain Valves (2/7/83) (AIR-120) Provides an acceptable means, but not the only means, of compliance with the requirements of the FARs for positive locking of fuel drain valves in the closed position. 20-120 Nondirectional Beacon Frequency Congestion (6/18/84) (ASM-500) Recommends several actions that the user can take to alleviate problems of frequency congestion in the 190-535 kHz frequency range. 20-121A Airworthiness Approval of Airborne Loran-C Navigation Systems for Use in the U.S. National Airspace System (NAS) (8/24/88) (AIR-120) Establishes an acceptable means, but not the only means, of obtaining airworthiness approval of airborne Loran-C navigation systems for use under VFR (visual flight rules) and IFR (instrument flight rules) within the conterminous United States, Alaska, and surrounding U.S. waters. 20-122A Anti-misfueling Devices: Their Availability and Use (1/29/91) (AFS-340) Includes information relating to the Society of Automotive Engineers (SAE) standard dimensions for fueling ports now being incorporated during new aircraft production by all General
Aviation Manufacturer’s Association member companies. It also makes recommendations to the fuel suppliers and Fixed Base Operators to change their fuel dispensing nozzles to meet the dimensions referenced in the SAE standard. 20-123 Avoiding Or Minimizing Encounters With Aircraft Equipped With Depleted Uranium Balance Weights During Accident Investigations (12/20/84) (AFS-330) Provides information and guidance to individuals who come in contact with depleted uranium contained in aircraft control surfaces during accident investigations. 20-124 Water Ingestion Testing for Turbine Powered Airplanes (9/30/85) (ANM-112) Describes a method of demonstrating compliance with the requirements of the FAR concerning the ingestion of water from the runway/taxiway surface into the airspeed system, the engine, and essential auxiliary power unit air inlet ducts of turbine engine power unit air inlet ducts of turbine engine powered airplanes. 20-125 Water in Aviation Fuels (12/10/85) (AFS-340) Alerts the aviation community to the potential hazards of water in aviation fuels. Additionally, it outlines recommended procedures to prevent, detect, and eliminate water in the fuel systems of aircraft. 20-126G Aircraft Certification Service Field Office Listing (11/30/99) (AFS-610) Provides the nearest points of contact for information regarding issuance of type and supplemental type certificates and changes, as well as issuances of production and/or airworthiness approvals.
20-127 Use of Society of Automotive Engineers (SAE) Class H11 bolts (7/8/87) (ANM- 110B) Provides guidance on the use of SAE Class H11 bolts in primary structure on all aircraft, including gliders and manned free balloons, and on aircraft engines and propellers. 20-128A Design Considerations for Minimizing Hazards Caused by Uncontained Turbine Engine and Auxiliary Power Unit Rotor and Fan Blade Failures (3/25/97) (ANM-114) Sets forth a method of compliance with the requirements of Sections 23.903(b)(1), 25.901(d) and 25.903(d)(1) of the FAR pertaining to design precautions taken to minimize the hazards to an airplane in the event of uncontained engine or auxiliary power unit rotor (compressor and turbine) failure and engine fan blade failures. It is for guidance and to provide a method of compliance that has been found acceptable. 20-129 Airworthiness Approval of Vertical Navigation (VNAV) Systems for use in the U.S. NAS and Alaska (9/12/88) (AIR-120) Establishes an acceptable means, but not the only means, of obtaining airworthiness approval of an airborne vertical navigation system for use under visual flight rules (VFR) and instrument flight rules (IFR) within the conterminous United States, Alaska and surrounding U.S. waters. 20-130A Airworthiness Approval of Navigation or Flight Management Systems Integrating Multiple Navigation Sensors (6/14/95) (AIR-130) Establishes an acceptable means, but not the only means, of obtaining airworthiness approval of a multisensor navigation or flight management systems integrating data
from multiple navigation sensors for use as a navigation system for oceanic and remote, domestic enroute, terminal, and non-precision instrument approach (except localizer, localizer directional aid (LDA) and simplified directional facility operations. This document does not address systems incorporating differential GPS capability. 20-131A Airworthiness and Operational Approval of Traffic Alert and Collision Avoidance Systems (TCAS II) and Mode S Transponders (3/29/93) (ANM-111) Provides guidance material for the airworthiness and operational approval of Traffic Alert and Collision Avoidance Systems (TCAS II) and Mode S transponders. Like all AC material, this AC is not mandatory and does not constitute a regulation. Issued for guidance purpose and to outline a method of compliance with the rules. 20-132 Public Aircraft (12/21/88) (AIR-200) Provides guidance that public aircraft status does not exist outside the territorial limits of the United States. 20-133 Cockpit Noise and Speech Interference Between Crewmembers (3/22/89) (AIR-121) Provides information about the relationship between flight crew members cockpit voice communication and cockpit noise levels. Guidance, on speech interference levels, noise measurement and measurement systems, and methods to improve cockpit communication, is provided for those manufacturers, owners or operators who believe cockpit noise may be a problem on their aircraft. This guidance material is relevant to the operation of all types of civil aircraft.
20-134 Test Procedures for Maximum Allowable Airspeed Indicators (2/16/90) (AIR-120) Provides guidance concerning test procedures which may be used in showing compliance with the standards in technical standards orders C 46a. 20-135 Powerplant Installation and Propulsion System Component Fire Protection Test Methods, Standards and Criteria (2/15/90) (ANM-112) Provides guidance for use in demonstrating compliance with the powerplant fire protection requirements of the Federal Aviation Regulations (FAR). Included in this document are methods for fire testing of materials and components used in the propulsion engines and APU installations, and in areas adjacent to designated fire zones, as well as the rationale for these methods. 20-136 Protection of Aircraft Electrical/Electronic Systems Against the Indirect Effects of Lightning (3/5/90) (ANM-111) Provides information and guidance concerning an acceptable means, but not the only means, of compliance with Parts 23, 25, 27, and 29 of the FAR as applicable for preventing hazardous effects, due to lightning, from occurring to electrical/electronic systems performing critical essential functions. This material is neither mandatory nor regulatory in nature and does not constitute a regulation. The applicant may elect to establish an alternative method of compliance that is acceptable to the FAA. 20-138 Airworthiness Approval of Global Positioning System (GPS) Navigation Equipment for Use as a
VFR and IFR Supplemental Navigation System (5/25/94) (AIR-130) Establishes an acceptable means, but not the only means, of obtaining airworthiness approval of Global Positioning System (GPS) equipment for use as a supplemental navigation system for oceanic and remote domestic en route, terminal, and nonprecision instrument approach (except localizer directional aid (LDA) and simplified directional facility (SDF) operations. 20-139 Commercial Assistance During Construction of Amateur-Built Aircraft (4/3/96) (AIR-230) Explains Federal Aviation Regulations and Federal Aviation Administration policy for the fabrication and assembly of amateur-built aircraft. Provides information and guidance in the construction of amateur-built aircraft, the manufacture of kits designed to be assembled into aircraft by amateurbuilders, and aircraft fabricated from plans for certification as amateur-built. 20-140 Guidelines for Design Approval of Aircraft Data Communications Systems (8/16/99) (AIR-130) Provides guidelines for design approval of aircraft data communications systems and applications primarily used for air traffic services. 20-141 Airworthiness and Operational Approval of Digital Flight Data Recorder Systems (10/5/99) (AIR-130) Provides guidance on design, installation, and continued airworthiness of Digital Flight Data Recorder Systems. It outlines one method of compliance with Title 14 of the Code of Federal Regulations. This AC is not mandatory nor is it a regulation.
20-142 Eligibility and Evaluation of U.S. Military Surplus Flight Safety Aircraft Parts, Engines, and Propellers (2/25/00) (AFS-307) Provides information and guidance for use in evaluating and determining the eligibility of U.S. military surplus flight safety critical aircraft parts (FSCAP), engines, and propellers for installation on FAA type-certificated products. 20-143 Installation, Inspection of Controls for General Aviation reciprocating Aircraft Engines (6/6/00) ACE-111 Provides guidance regarding the inspection, maintenance, and installation of engine controls with emphasis on the airframe portion of these systems. It provides a supplement to, but does not replace, the procedures in the manufacturers’ maintenance manuals. Where the content of the AC differs from, or conflicts with the manufacturers’ maintenance manual, instructions contained in the manufacturers’ manual take precedence over the guidelines provide in this AC. 20-144 Recommended method for FAA Approval of Aircraft Fire Extinguishing System Components (9/11/00) (ANM-140L) Provides guidance on the various aspects that should be considered in the FAA approval process of fire extinguishing system components manufactured under a Production Certificate (PC), components to be FAA approved under the Part Manufacturer Approval (PMA) process, or design changes to components originally approved by either method. This AC does not constitute a regulation, however, it provides a method, for obtaining approval of aircraft fire extinguishing system components. This is intended to enhance the standardization of all
FAA Aircraft Certification Offices (ACO) and Manufacturing Inspection District Offices (MIDO) in the approval process of the critical components of an aircraft fire extinguishing system. 4 20-145 Guidance for Integrated Modular Avionics (IMA) that implement TSO-C153 authorizes Hardware Elements (2/23/04) (AIR-120) This advisory circular (AC) establishes an acceptable means, but not the only means, to obtain Federal Aviation Administration’s (FAA) airworthiness approval for the installation of an Integrated Modular Avionics (IMA) System that uses hardware elements authorized under Technical Standard Order (TSO)-C153, Integrated Modular Avionics Hardware Elements. The FAA’s TSO process is a means for obtaining FAA design and production approval for an appliance, system, or product; however, the TSO authorization does not provide installation approval.
This AC provides guidance for applicants involved in the integration, installation, certification, and continued airworthiness of IMA systems into an aircraft or engine, when the IMA system utilizes hardware elements that comply with TSO-C153. The guidance applies to the entire IMA system, not just the hardware elements. The guidance is specific to installations of these systems on aircraft or engines approved under Title 14 of the Code of Federal Regulations (14 CFR) parts 23, 25, 27, 29, 33, and 35. 4 20-146 Methodology for Dynamic Seat Certification by Analysis for Use in Part 23, 25, 27, and 29 Airplanes and Rotorcraft (5/19/03) (ACE-100) This advisory circular (AC) sets forth an acceptable means, but not the only means, for demonstrating compliance to the following by computer modeling analysis techniques validated by dynamic tests: • Title 14 Code of Federal Regulations (14 CFR) parts 23, 25, 27, and 29, §§ 23.562, 25.562, 27.562, and 29.562. • The Technical Standard Order (TSO) associated with
the above regulations, TSO- C127/C127a. 4 20-147 Turbojet, Turboprop, and Turbofan Engine Induction System Icing and Ice Ingestion (02/02/04) (AIR-100) This advisory circular (AC) provides guidance and acceptable methods, but not the only methods, for demonstrating compliance with the applicable engine induction system icing and engine ice ingestion requirements. These requirements are applicable to the Federal Aviation Regulations, parts 23, 25, and 33 of Title 14 of the Code of Federal Regulations (14 CFR parts 23, 25, and 33). The primary purpose of this AC is to reduce inconsistencies and eventual surprises to both engine manufacturers and engine installers, when installing a part 33 certified engine in a part 23 or 25 aircraft. 20 21-1B Production Certificates (5/10/76) (AIR-200) Provides information concerning Subpart G of Federal Aviation Regulations (FAR) Part 21, and sets forth acceptable means of compliance with its requirements. 21-2J Export Airworthiness Approval Procedures (6/27/00) (AIR-210/AFS-610) Contains guidance and information on procedures for exporting aeronautical products and related special requirements submitted to the Federal Aviation Administration by other governments. SN: 050-007-01293-4, 21-4B Special Flight Permits for Operation of Overweight Aircraft (7/30/69) (AIR- 200) Furnishes guidance concerning special flight permits necessary to operate an aircraft in excess of its usual maximum certificated takeoff weight.
21-5N Announcement of Availability of Summary of Supplemental Type Certificates, (Paper) January 1998 (AFS-610) Announces the availability to the public of a revised paper edition of the Summary of Supplemental Type Certificates, dated January 1998. Also available at Internet site http://avinfo.faa.gov. 21-6A Production Under Type Certificate Only (7/1/82) (AIR-200) Provides information concerning Subpart F of FAR Part 21, and sets forth an acceptable means, not the sole means, of compliance with its requirements. SN 050-007-00636-5. 21-9A Manufacturers Reporting Failures, Malfunctions, or Defects (5/26/82) (AIR-200) Provides information to assist manufacturers of aeronautical products (aircraft, aircraft engines, propellers, appliances, and parts) in notifying the Federal Aviation Administration of certain failures, malfunctions, or defects, resulting from design or quality control problems, in the products which they manufacture. 21-10A Flight Recorder and Cockpit Voice Recorder Underwater Locating Devices (4/19/83) (ANM-110) This AC provides an acceptable means of showing compliance with the underwater locating device (ULD) requirements of the Federal Aviation Regulations for recorder ULD’s. 21-12A Application for U.S. Airworthiness Certificate, FAA Form 8130-6 (OMB 2120-0018) (3/26/87) (AIR-220)
Provides instructions on the preparation and submittal of subject form.
21-13 Standard Airworthiness Certification of Surplus Military Aircraft and Aircraft Built from Spare and Surplus Parts (4/5/73) (AIR-200) Provides guidance and instruction on establishing eligibility and submitting application for civil airworthiness certification of surplus military aircraft and aircraft assembled from spare and surplus parts, under FAR 21. (d) when an FAA Type Certificate has been issued under FAR 21.21. or FAR 21.27. 21-15L Announcement of Availability: Aircraft, Aircraft Engines and Propeller Type Certificate Data Sheets and Specifications (4/12/99) (AFS-610) Provides information concerning the availability of the 1999 edition of the subject publication. 21-16D RTCA Document DO-160C (7/21/98) (AIR-130) Calls attention to RTCA, Inc. (formerly Radio Technical Commission for Aeronautics) Document No. DO-160D, “Environmental Conditions and Test Procedures for Airborne Equipment,” dated July 29, 1997, and discusses how the document may be used in showing compliance with airworthiness requirements. 21-17 Carriage of Cargo in Restricted Category Aircraft and Other Special Purpose Operations (3/15/82) (AIR-200) Advises that the carriage of cargo in a restricted category aircraft is considered a restricted category special purpose operation and provides procedures for designating other special purpose operations under FAR 21.25(b) (7). SN 050-007-00638-1.
21-18 Bilateral Airworthiness Agreements (8/20/82) (AIR-110) Makes available to interested persons copies of all current U.S. Bilateral Airworthiness Agreements (BAA) together with an explanation of their intent. SN 050-007- 00614-4. 421-19A Installation of Used Engines In New Production Aircraft (07/02/03) (AIR-200) Advises that under certain specified criteria, used engines may be used in new production aircraft. 21-20B Supplier Surveillance Procedures (4/22/96) (AIR-230) Clarifies and revises methods acceptable to the Administrator for surveillance of suppliers by the Federal Aviation Administration Production Approval Holders. It applies to products and parts thereof, submitted for airworthiness certification or approval after design approval (e.g., type certificate) and a production approval has been granted. 21-21 Use Of Automobile Gasoline In Agricultural Aircraft (8/24/84) (AIR-100) Sets forth acceptable conditions under which automobile gasoline (autogas) may be used in restricted category agricultural aircraft powered by Pratt and Whitney R-985 and R-1340 radial engines, and being used in agricultural operations under Federal Aviation Regulations Part 137. 21-22 Injury Criteria for Human Exposure to Impact (6/20/85) (AIR-120) Describes a range of impact trauma which may be used to establish bases for acceptance levels or performance criteria in the evaluation of occupant
survivability characteristics in civil aircraft. 21-23A Airworthiness Certification of Civil Aircraft Engine, Propellers, and Related Products (10/20/00) (AIR-4) Provides information on the Federal Aviation Administration’s (FAA) objectives, regulations, and general practices for the United States of America airworthiness certification or acceptance of civil aeronautical products imported to the U.S. 21-24 Extending a Production Certificate to a Facility Located in a Bilateral Airworthiness Agreement Country (4/14/89) (AIR-220) Contains information and guidance concerning: (1) FAA production certificate (PC) holders located in the U.S. that plan to extend their PC to include a facility located in another country; (2) and the issuance of a PC to an applicant located in the U.S. when the applicant is engaged in a multinational coproduction program whereby major manufacturing facilities will be located in other countries. 21-25A Approval of Modified Seats and Berths Initially Approved Under a Technical Standard Order (6/3/97) (AFS- 610) Provides information on approvals required for modifications to TSO’d seating systems. This revision incorporates guidance regarding TSO- C127 seating systems and additional information on marking and flammability testing requirements. 21-26 Quality Control for the Manufacture of Composite Structures (6/26/89) (AIR-220) Provides information and guidance concerning and acceptable means, but not the only means, of demonstrating compliance with the requirements of FAR Part 21, Certification Procedures
for Products and Parts, regarding quality control (QC) systems for the manufacture of composite structures involving fiber reinforced materials, e.g., carbon (graphite), boron, aramid (Kevlar), and glass reinforced polymeric materials. Provides guidance regarding the essential features of QC systems for composites as mentioned in AC 20-107. 21-26, Chg. 1 (1/26/90) Modifies the term “Rheometrics Dynamic Spectroscopy (RDS),” which has been shown to be specific to one manufacturer, to “Dynamic Rheological Analysis,” which is more generic term. 21-27 Production Certification Multinational/Multicorporate Consortia (7/14/89) (AIR-220) Provides information and describes criteria to be emphasized in evaluating and approving the quality control system of a multinational and/or multicorporate consortium seeking a production certificate (PC). This AC would not apply to a type certificate holds a PC. Production Certificated extensions are addressed in AC 21-24. 21-28 Airworthiness Certification of U.S. Produced Aircraft and Engine Kits Assembled Outside the United States (6/20/90) (AIR-220) Provides information and guidance concerning airworthiness certification requirements for aircraft or aircraft engines, assembled from kits by aircraft or aircraft engine manufacturers located in other countries. 21-29B Detecting and Reporting Suspected Unapproved Parts (2/20/98) (AVR-20) Provides information and guidance to the aviation community for detecting
and reporting Suspected Unapproved Parts. 21-29B, Chg. 1 (3/13/00) (AVR-20) Implements revised FAA Form 8120, Suspected Unapproved Parts Notification, dated 11/99. 21-31 Quality Control for the Manufacture of Non-Metallic Compartment Interior Components (11/15/91) (AIR-220) Provides information and guidance concerning compliance with the requirements of Federal Aviation Regulations (FAR) Part 21, Certification Procedures for Products and Parts. 21-32A Control of Products and Parts Shipped Prior to Type Certificate Issuance (3/19/96) (AIR-230) Provides a means, but not the only means, to control products and parts shipped prior to the issuance of a type certificate or supplemental type certificate by a manufacturer with an approved production inspection system or production certificate. This AC broadens the scope of AC 21-32 by including completed aircraft, aircraft engines, propellers, and parts thereof ship prior to TC/STC issuance. 21-33 Quality Assurance of Software Used In Aircraft or Related Products (2/3/93) (AIR-220) Provides an acceptable means, but not the only means, to show compliance with the quality assurance requirements of FAR Par 21, Certification Procedures for Products and Parts, as applicable to the production of software used in type certificated aircraft or related products (airborne software). Also provides supplemental guidance for the establishment of a quality control or inspection to control the development and production of software used in type certification aircraft.
21-34 Shoulder Harness-Safety Installations (6/4/93) (AIR-120) Provides information and guidance pertinent to an acceptable means, but not the only means, for installation of shoulder harness and safety belt restraint systems at all seat locations on all previously type-certificated aircraft. 21-35 Computer Generated/Stored Records (6/4/93) (AIR-220) Provides information and guidance concerning controls for managing information systems that generate and store records used in the manufacture of products and parts. Describes an acceptable means, but not the sole means, of compliance with the Federal Aviation Regulations (FAR). 21-36 Quality Assurance Control for Products Acceptance Software. (8/11/93) (AIR-200) Provides information and guidance concerning control of software and related digital input/output data (used by production approval holders (PAH) and their suppliers during manufacture, inspection and/or test) designed for use in the acceptance of airborne products. Provides an acceptable means, but not the only means, of compliance with the applicable Federal Aviation Regulations. 21-37 Primary Category Aircraft (6/14/94) (AIR-110) Provides guidance for complying with Part 21 of Subchapter C, Chapter 1, Title 14 of the Code of Federal Regulations (CFR), which contains the certification procedures for products and parts.
21-40 Application Guide for Obtaining a Supplemental Type Certificate (5/6/98) (AFS-610) Intended as a certification guide and checklist for obtaining a Supplemental Type Certificate (STC). Title 14 of the Code of Federal Regulations (14 CFR) and Federal Aviation Administration (FAA) Directives (orders and notices) are the final authority and take precedence over this document. 21-41 Continued Use of MIL-S-8879C, General Specification for Screw Threads (2/26/99) (AIR-120) Provides information, clarification, and procedural guidance concerning the Inactivation of MIL-S-8879Cm Screw Threads, Controlled Radius Root with Increased Minor Diameter, as it relates to the civil aviation industry. 21.17-1A Type Certification-Airships (9/25/92) (ACE-100) Describes two acceptable criteria for the type certification of airships that may be used by an applicant in showing compliance with section 21.17(b) of the Federal Aviation Regulations (FAR), Part 21. General guidance relative to airship type certification is also provided. 21.17-1A, Chg. 1 (10/30/92) 21.17-2A Type Certification-Fixed Wing Gliders (Sailplanes) Including Powered Gliders (2/10/93) (ACE-112) Provides information and guidance concerning acceptable means of showing compliance with Section 21.17(b) of Part 21 of the Federal Aviation Regulations (FAR) for type certification of gliders and powered gliders. General guidance relative to glider type certification is also provided.
21.17-3 Type Certification of Very Light Airplanes Under FAR 21.17(b) (12/21/92) (AIR-110) Provides a means but not the only means for the type, production, and airworthiness certification of very light airplanes (VLA); and designates the “Joint Aviation Requirements for Very Light Aeroplanes” (JAR-VLA), issued April 25, 1990, by the Joint Aviation Authorities (FAA) of Europe as an acceptable airworthiness criteria that provides in equivalent level of safety under FAR 21.17(b) for Federal Aviation Administration (FAA) type certification of VLA as a special class of aircraft. Provides other acceptable uses of the JAR-VLA in the United States aircraft certification regulatory system. 21.25-1 Issuance of Type Certificate: Restricted Category Agricultural Airplanes (12/1/97) (ACE-111) Provides information and guidance for obtaining a type certificate in the restricted category under Title 14 of the Code of Federal Regulations (14 CFR) Part 21, Section 21.25, for small single-engine piston and turbopropeller driven airplanes, which will be used for agricultural special purpose operations. It also provides an acceptable means, but not the only means, of meeting the requirements of 14 CFR part 21 for the issuance of a type certificate in the restricted category. 21.101-1 Advisory Material for the Establishment of the Certification Basis of Changed Aeronautical Products (8/3/01) (AIR-110) Provides guidance for establishing the certification basis for changed 14 CFR part 25 aeronautical products, including identifying the conditions under which it will be necessary to apply for a new type certificate.
21.303-2H Announcement of Availability: Parts Manufacturer Approvals--1992 (Microfiche) (10/13/92) (AFS-610) Provides information concerning how to obtain the latest edition of parts manufacturing approvals, which are valid through August 1992. PMAs since 1992 are available at Internet site http://av-info.faa.gov. 23-2 Flammability Tests (8/20/84) (ACE-111) Provides information and guidance concerning compliance with FAR Part 23 and CAR Part 3 applicable to flammability tests for various materials, components, and electrical wire. 23-3 Structural Substantiation of Secondary Structures (9/5/85) (ACE-111) Provides information and guidance concerning acceptable means, but not the only means, of demonstrating compliance with the requirements of Part 23 of the Federal Aviation Regulations (FAR) applicable to the structural substantiation of secondary structures such as fairings, cowlings, antennae, etc. 23-4 Static Strength Substantiation of Attachment Points for Occupant Restraint System Installations (6/20/86) (ACE-111) Provides information and guidance concerning an acceptable means, but not the only means, of compliance with Part 23 of the Federal Aviation Regulations (FAR) applicable to the static strength substantiation of the attachment points for occupant restraint system installations which have both a safety belt and shoulder harness. 23-5 Cutouts in a Modified Fuselage of Small Airplanes
(8/6/86) (ACE-111) Provides information and guidance concerning acceptable means of compliance with Part 23 of the Federal Aviation Regulations (FAR) applicable to the structural substantiation of a fuselage modified by incorporation of large or small cutouts. 23-6 Interpretation of Failure for Static Structural Test Programs (9/2/86) (ACE-111) Provides information and guidance concerning the interpretation of failure for small airplanes for static structural test programs. 23-7 Substantiation for an Increase in Maximum Weight, Maximum Landing Weight, or Maximum Zero Fuel Weight (7/1/87) (ACE-100) Provides information and guidance concerning acceptable means, but not the only means of compliance with Part 23 of the Federal Aviation Regulations (FAR) applicable to structural substantiation for an increase in maximum weight, maximum landing weight, or maximum zero fuel weight. 423-8B Flight Test Guide for Certification of Part 23 Airplanes (8/14/03) (ACE-100) Provides information and guidance concerning compliance with Part 23 of the Federal Aviation Regulations (FAR) concerning flight tests and pilot judgments. SN 050-007-00817-1 23-9 Evaluation of Flight Loads on Small Airplanes with T, V, +, or Y Empennage Configurations (1/27/88) (ACE-111) Provides information and guidance concerning compliance with Part 23 of the Federal Aviation Regulations (FAR) applicable to evaluation of empennage design flight loads on configurations where the horizontal tail
surfaces are supported by the vertical tail, or have appreciable dihedral. 23-10 Auxiliary Fuel Systems for Reciprocating and Turbine Powered Part 23 Airplanes (8/5/91) (ACE-111) Provides information and guidance concerning acceptable means of showing compliance with Part 23 of the Federal Aviation Regulations (FAR), applicable to auxiliary fuel systems in Part 23 airplanes. It is intended to be used for auxiliary fuel system installations in the airplane including fuselage, wing, or external configurations. 23-11 Type Certification of Very Light Airplanes with Powerplants and Propellers Certificated to Parts 33 and 35 of the Federal Aviation Regulations (FAR) (12/2/92) (ACE-111) Provides an acceptable means of compliance with Part 23 of the FAR for type certification of certain small airplanes. 23-12 Structural Substantiation of Part 23 Airplane Modifications Involving Increased Engine Power (1/27/93) (ACE-111) Provides information and guidance concerning acceptable means of demonstrating compliance with the requirements of Part 23 of the Federal Aviation Regulations (FAR) applicable to the structural substantiation of modifications involving increased engine power. 23-13 Fatigue and Fail-Safe Evaluation of Flight Structure and Pressurized Cabin for Part 23 Airplanes (4/15/93) (ACE-111) Provides information and guidance concerning an acceptable means of demonstrating compliance with the requirements of Part 23 of the Federal Aviation Regulations (FAR) regarding
fatigue and fail-safe evaluation of metallic airplane structure. 23-14 Type Certification Basis for Conversion from Reciprocating Engine to Turbine Engine-Powered Part 23 Airplanes (9/30/93) (ACE-100) Provides information and guidance concerning an acceptable means of showing compliance with Part 23 through amdt.23-45 of the Federal Aviation Regulations applicable to replacing reciprocating engines with gas turbine engines (turbopropeller, turbojet, or turbofan). 423-15A Small Airplane Certification Compliance Program (12/30/03) (ACE-111) Provides a compilation of historically acceptable means of compliance to specifically selected sections of Part 23 of the Federal Aviation Regulations that have become burdensome for small low performance airplanes to show compliance. However, applicability of these means of compliance remains the responsibility of the certification manager for each specific project. Utilization of these means of compliance does not affect the applicability of any other certification requirements that fall outside the scope of this AC. 423-16A Powerplant Guide for Certification in Part 23 Airplanes (02/23/04) (ACE-111) Consolidates into a single document existing policy documents applicable to the powerplant installation in normal, utility, acrobatic, and commuter category airplanes; and, certain ACs that cover specific paragraphs of the regulations. SN 050-007-01285-3 23-17A Systems and Equipment Guide For Certification of Part 23 Airplanes (6/27/02) (ACE-100)
Provides information and guidance concerning an acceptable means, but not the only means, for showing compliance with Title 14 Code of Federal Regulations (14 CFR) Part 23 for the certification of systems and equipment in normal, utility, acrobatic, and commuter category airplanes. SN 050-007-01332-9 23-18 Installation of Terrain Awareness and Warning System (TAWS) Approved for Part 23 Airplanes (6/14/00) (ACE-111) Establishes an acceptable means, but not the only means, of obtaining FAA airworthiness approval for the installation of a TAWS that has been approved under Technical Standard Order (TSO)-C151A, Terrain Awareness and Warning System, in a Part 23 airplane. The FAA’s TSO process is a means for obtaining FAA design and performance approval for an appliance, system, or product; however, the TSO does not provide installation approval. This AC serves to provide guidance for designing an acceptable installation for a TAWS that complies with TSO-C151a.
The guidance provided is specific to installations of these systems on airplanes certificated under Title 14 of the Code of Federal Regulations Part 23. It describes the airworthiness considerations for such installations as they apply to the unique features of the TAWS and the interface of the TAWS with other systems on the airplane. 423-19 Airframe Guide for Certification of Part 23 Airplanes (01/27/03) (ACE-111) Provides information and guidance concerning acceptable means, but not the only means, of complying with Title 14 of the Code of Federal Regulations (14 CFR) part 23 Subpart C and portions of Subpart D. It consolidates the substance of existing Civil Aeronautics Administration (CAA) and Federal Aviation Administration (FAA) letters into a
single reference. It also presents information from certain presently existing AC's that cover general topics and specific airworthiness standards. Material in this AC is neither mandatory nor regulatory. AC methods may be freely chosen, or ignored, by an applicant who seeks to demonstrate regulatory compliance. Use of FAA published AC guidance frequently speeds the design approval process for an applicant. 423-20 Acceptance Guidance on Material Procurement and Process Specifications for Polymer Matrix Composite Systems (09/19/03) (ACE-111) Provides information and guidance concerning an acceptable means, but not the only means, of compliance with Title 14 of the Code of Federal Regulations (14 CFR) part 23. It is applicable to the material and process specifications, or other documents, used to ensure sufficient control of composite prepreg materials in normal, utility, acrobatic, and commuter category airplanes. Material in this AC is neither mandatory nor regulatory in nature and does not constitute a regulation. 23.562-1 Dynamic Testing of Part 23 Airplane Seat/Restraint Systems and Occupant Protection (6/22/89) (ACE-111) Provides information and guidance regarding compliance with Part 23 of the Federal Aviation Regulations (FAR) applicable to dynamic testing of airplane seats. 23.607-1 Self-Locking Nuts on Bolts Subject to Rotation (8/24/84) (ACE-111) Provides information and guidance concerning compliance with Part 23 for self-locking nuts used on bolts subject to rotation in operation. 23.629-1A Means of Compliance with Section 23.629, “Flutter” (10/23/85) (ACE-111)
Presents information and guidance to provide one means, but not the only means, of complying with Section 23.629, Flutter (including flutter, airfoil divergence, and control reversal) of Part 23 of the Federal Aviation Regulations. 23.1309-1C Equipment, Systems, and Installations in Part 23 Airplanes (3/12/99) (ACE-111) Provides guidance and information for an acceptable means, but not the only means, for showing compliance with the requirements of Section 23.1309(a) and (b) (amendment 23-49) for equipment, systems, and installations in Title 14 Code of Federal Regulations (14 CFR) Part 23 airplanes. 23.1311-1A Installation of Electronic Displays in Part 23 Airplanes (3/12/99) (ACE-111) Provides an acceptable means of showing compliance with Title 14 of the Code of Federal Regulations (14 CFR) applicable to the installation of electronic displays in Part 23 airplanes. 23.1419-2B Certification of Part 23 Airplanes for Flight in Icing Conditions (9/26/02) (ACE-100) Sets forth an acceptable means, but not the only means, of demonstrating compliance with the ice protection requirements in 14 CFR Part 23. The FAA will consider other methods of demonstrating compliance that an applicant may present. 23.1521-1B Type Certification of Automobile Gasoline in Part 23 Airplanes with Reciprocating Engines (3/2/95) (ACE-111) Sets forth acceptable means of compliance with Part 23 of the Federal Air Regulations (FAR), for approval/certification to use automobile gasoline with or without oxygenates (alcohol, ethers, etc.) in
Part 23 airplanes. These procedures also apply to those airplanes approved/certificated under previous regulations superseded by Part 23.
23.1521-2 Type Certification of Oxygenates and Oxygenated Gasoline Fuels in Part 23 Airplanes with Reciprocating Engines (1/21/93) (ACE-111) Provides information and guidance concerning an acceptable means of compliance with Part 3 of the Civil Air Regulations (CAR) and Part 23 of the Federal Aviation Regulations (FAR), applicable to approval procedures for certification of alternate fuels. Also apply to those airplanes approved under Part 4a of the CAR and Aeronautics Bulletin 7a. 23.1521-2, Chg. 1 (4/24/96) (ACE-111) Clarifies the Scope and makes the Scope and Purpose of this AC consistent with AC 23.1521-1B, Type Certification of Automobile Gasoline in Part 23 Airplanes with Reciprocating Engines. 25-4 Inertial Navigation Systems (INS) (2/18/66) (ANM-100) Sets forth an acceptable means for complying with rules governing the installation of inertial navigation systems in transport category aircraft. 25-5 Installation Approval on Transport Category Airplanes of Cargo Unit Load Devices Approved as Meeting the Criteria in NAS 3610 (6/3/70) (AIR-120) Sets forth an acceptable means, but not the sole means, of complying with the requirements of the Federal Aviation Regulations (FAR’s) applicable to the installation on transport category airplanes of cargo load devices approved as meeting the criteria in NAS 3610. 25-7A Flight Test Guide for Certification of Transport Category Airplanes (3/31/98) (ANM-111)
Provides guidelines for the flight test evaluation of transport category airplanes. SN 050-007-01214-4. 25-7A, Chg 1 (6/3/99) (ANM-111) Provides updated guidance to ensure consistent application of certain airworthiness requirements adopted by Amendments 25-92 and 25-98 SN 050-007-01271-3 25-8 Auxiliary Fuel System Installations (5/2/86) (ANM-112) Sets forth acceptable means, but not the sole means, by which compliance maybe shown with auxiliary fuel system installation requirements in accordance with the Federal Aviation Regulations identified within. SN 050-007-00741-8. 25-9A Smoke Detection, penetrating, and Evacuation Tests and Related Flight Manual Emergency Procedures (1/6/94) (ANM-111) Provides guidelines for the conduct of certification tests relating to smoke detection, penetration, and evacuation and to evaluate related Airplane Flight Manual (AFM) procedures. These guidelines may be used to reduce the number of decisions based solely on judgment in conducting tests and evaluating test results. While not mandatory this AC offers a method of demonstrating compliance with the applicable airworthiness requirements. 25-10 Guidance for Installation of Miscellaneous Nonrequired Electrical Equipment (3/6/87) (ANM-110) Sets forth a method of compliance with the requirements of Part 25 of the Federal Aviation Regulations pertaining to installations of miscellaneous, nonrequired electrical equipment in transport category airplanes. Provides an example of a
method of compliance that has been found acceptable. 25-11 Transport Category Airplane Electronic Display Systems (7/16/87) (ANM-110B) Provides guidance for acceptance of cathode ray tube (CRT) based electronic display systems used for guidance, control, or decision-making by the pilots of transport category airplanes. 25-12 Airworthiness Criteria for the Approval of Airborne Windshear Warning Systems in Transport Category Airplanes (11/2/87) (ANM-111) Provides guidance for the airworthiness approval of airborne windshear warning systems in transport category airplanes. 25-13 Reduced and Derated Takeoff Thrust (Power) Procedures (5/4/88) (ANM-112) Provides guidance for the certification and use of reduced thrust (power) for takeoff and derated takeoff and derated thrust on turbine powered transport category airplanes. Serves as a ready reference for those involved with airplane certification and operation. 25-15 Approval of Flight Management Systems in Transport Category Airplanes (11/20/89) (ANM-111) Provides guidance material for the airworthiness approval of flight management systems (FMS) in transport category airplanes. Is issued for guidance purposes and to outline a method of compliance with the rules. In lieu of following this method without deviation, the applicant may elect to follow an alternate method, provided the alternate method is also found by the FAA to be an acceptable means of complying with the requirement of Part 25.
25-16 Electrical Fault and Fire Prevention and Protection (4/5/91) (ANM-111) Provides information and guidance on electrically caused faults, overheat, smoke, and fire in transport category airplanes. Acceptable means are provided to minimize the potential for these conditions to occur, and to minimize or contain their effects when they do occur. 25-17 Transport Airplane Cabin Interiors Crashworthiness Handbook (7/15/91) (ANM-114) Provides acceptable certification methods, but not necessarily the only acceptable methods, for demonstrating compliance with the crashworthiness requirements of Part 25 of the FAR for transport category airplanes. SN 050-007-00915-1. 25-18 Transport Category Airplanes Modified for Cargo Service (1/6/94) (ANM-114) Provides guidance for demonstrating compliance with the FAR pertaining to transport category airplanes converted for use in all-cargo or combination passenger/cargo (combi) service and the relationship of those regulations to the requirements of Parts 121and 135 of the FAR. 25-19 Certification Maintenance Requirements (11/28/94) (ANM-113) Provides guidance on the selection, documentation, and control of Certification Maintenance Requirements (CMR’s). 25-20 Pressurization, Ventilation, and Oxygen Systems Assessment for Subsonic Flight Including High Altitude Operation (9/10/96) (ANM-111) Provides guidance on methods of compliance with the requirements of
part 25 of the Federal Aviation Regulations pertaining to pressurization, ventilation, and oxygen systems, especially as they pertain to high altitude subsonic flight. As with all AC material, it is not mandatory and does not constitute a regulation. The applicant may elect to follow alternate methods provided that these methods are also found by the FAA to be an acceptable means of complying with the requirements of part 25. Because the guidance on the methods of compliance presented in this AC are not mandatory, the terms "shall" and "must" when used herein, apply only to an applicant that chooses to follow a particular method without deviation. 25-21 Certification of Transport Airplane Structure (9/1/99) (ANM-110) Provides guidance to airplane manufacturers, modifiers, foreign regulatory authorities, and FAA transport airplane type certification engineers and their designees. 25-22 Certification of Transport Category Airplane Mechanical Systems (3/14/00) (ANM-112) Provides methods acceptable to the Administrator for showing compliance with the type certification requirements for transport airplane mechanical systems and equipment installations. 25-23 Airworthiness Criteria for the Installation Approval of a Terrain Awareness and Warning System (TAWS) for Part 25 Airplanes (5/22/00) (ANM-130L) Describes an acceptable means for obtaining FAA airworthiness approval for the installation of a Terrain Awareness and Warning System (TAWS) that has been approved under Technical Standard Order (TSO)- C151a.
25-24 Sustained Engine Imbalance (8-2-00) (ANW-100) Sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of 14 CFR Part 25 related to the aircraft design for sustained engine rotor imbalance conditions. While these guidelines are not mandatory, they are derived from extensive Federal Aviation Administration (FAA) and industry experience in determining compliance with the pertinent Federal Aviation Regulations (FAR). 25.253-1A High-Speed Characteristics (12/27/76) (ANM-110A) Sets forth an acceptable means, but not the only means, by which compliance may be shown with FAR 25.253 during certification flight tests. 25.335-1A Design Dive Speed (9/29/00) (ANM-115) Sets forth an acceptable means , but not the only means, of demonstrating compliance with the provisions of part 25 of the Federal Aviation Regulations (FAR) related to the minimum speed margin between design cruise speed and design dive speed for transport category airplanes. 25.491-1 Taxi, Takeoff, and Landing Roll Design Loads (10-30-00) (ANM-115) Sets forth acceptable methods of compliance with provisions of Part 25 of the FAR dealing with the certification requirements for taxi, takeoff, and landing roll design loads. Guidance information is provided for showing compliance with section 25.491 of the FAR relating to structural design for airplane operation on paved runways and taxiways normally used in commercial operations.
25.562-1A Dynamic Evaluation of Seat Restraint Systems & Occupant Protection on Transport Category Airplanes (1/19/96) (ANM-14) Provides information and guidance regarding compliance with the provisions of Part 25 of the Federal Aviation Regulations applicable to dynamic testing of seats intended for use in transport category airplanes. 25.571-1C Damage-Tolerance and Fatigue Evaluation of Structure (4/29/98) (ANM-115) Provides guidance for compliance with the provisions of 14 CFR Part 25 of the Federal Aviation Regulations (FAR) pertaining to the damage-tolerance and fatigue evaluation requirements for transport category aircraft structure. It also provides guidelines for the evaluation of scatter factors for the determination of life for parts categorized as safe-life. 25.629-1A Aeroelastic Stability Substantiation of Transport Category Airplanes (7/23/98) (ANM-115) Provides guidance material for acceptable means for demonstrating compliance with the provisions of part 25 of the FAR dealing with the design requirements for transport category airplanes to preclude the aeroelastic instabilities of flutter, divergence and control reversal. 25.672-1 Active Flight Controls (11/15/83) (ANM-110B) Sets forth an equivalent means of complying with the provisions of Part 25 of the Federal Aviation Regulations (FAR) pertaining to the certification requirements of active flight controls. The procedures set forth herein apply to load alleviation systems (SAS), and flutter suppression systems (FSS). These procedures provide compliance with Part 25 under the equivalent safety provisions of Section
21.21(b)(1) in addition to compliance with the applicable sections of Part 25. 25.703-1 Takeoff Configuration Warning Systems (3/17/93) (ANM-111) Provides guidance for the certification of takeoff configuration warning systems installed in transport category airplanes. 25-723.1, Stock Absorption Test (5/25/01) (ANM-110) This advisory circular (AC) sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of part 25 of the Federal Aviation Regulations (FAR) related to the use of landing gear shock absorption tests and analyses to determine landing loads for transport category airplanes. 25.735-1, Brakes & Braking Systems Cert Test & Analysis (4/10/02) (ANM-112) Describes an acceptable means for obtaining FAA airworthiness approval concerning new or revised requirements for braking systems, and associated test conditions for braking systems, installed in transport category airplanes. 25.773-1 Pilot Compartment View for Transport Category Airplanes (1/8/93) (ANM-111) Provides guidance for demonstrating compliance with the airworthiness standards for transport category airplanes pertaining to pilot compartment view. These criteria include the properties of transport materials necessary to assure adequate visibility from the flight deck. 425.775-1 Windows and Windshields (01/17/03) (ANM-110) Sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of Title 14, Code of Federal Regulations (14
CFR) part 25 pertaining to the certification requirements for windshields, windows, and mounting structure. Guidance information is provided for showing compliance with § 25.775(d), relating to structural design of windshields and windows for airplanes with pressurized cabins. Terms used in this AC, such as “shall” or “must,” are used only in the sense of ensuring applicability of this particular method of compliance when the acceptable method of compliance described herein is used. Other methods of compliance with the requirements may be acceptable. While these guidelines are not mandatory, they are derived from extensive Federal Aviation Administration (FAA) and industry experience in determining compliance with 14 CFR. This AC does not change, create any additional, authorize changes in, or permit deviations from, regulatory requirements. 25.783-1 Fuselage Doors, Hatches, and Exits (12/10/86) (ANM-110) Sets forth acceptable means of compliance with the provisions of Part 25 of the Federal Aviation Regulations (FAR) dealing with the certification requirements of fuselage doors.
Guidance information is provided for showing compliance with structural and functional safety standards for doors and their operating systems. The intent of the requirements and some acceptable means of compliance are discussed. Other means are acceptable if they meet the intent of the regulations. For the propose of showing compliance with section 25.783 of FAR, hatches and exits are also considered to be doors. 25.785-1A Flight Attendant Seat and Torso Restraint System Installations (1/6/94) (ANM-114) Provides information and guidance regarding an acceptable means, but not the only means, of compliance with the portions of Sections 25.785 and
121.311 of the FAR, which deals with flight attendant seats. 25-795-1, Flight Deck Intrusion Resistance (1/10/02) (ANM-115) Sets forth an acceptable means, but not the only means of demonstrating compliance with the provisions of the airworthiness standards for transport category airplanes related to the airplane design for flight deck (also referred to as the pilot compartment or cockpit) intrusion resistance. 25.795-2, Flight deck Penetration Resistance (1/10/02) (ANM-115) Sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of the airworthiness standards for transport category airplanes related to the airplane design for flight deck penetration resistance. 25.803-1 Emergency Evacuation Demonstrations (11/13/89) (ANM-114) Provides guidance material on a means, but not the only means, of compliance with the FAR concerning (1) conduct of full-scale emergency evacuation demonstrations, and (2) use analysis and tests for emergency evacuation demonstrations in lieu of conducting an actual demonstration. 25.807-1 Uniform Distribution of Exits (8/13/90) (ANM-114) Provides guidance material for acceptable means, but not the only means, of demonstrating compliance with the requirements for distributing required passenger emergency exits uniformly. Addresses only those passenger-carrying airplanes, including mixed passenger/cargo (“combi”) configurations, with a type certification basis for Amendment 25-15 or later with respect to Section 25.807(c) or airplanes with an earlier type certification basis required by Section
25.2 to meet Section 25.807, Amendment 25-15. Does not address airplanes with only one pair of required exits. 25.812-1A Floor Proximity Emergency Escape Path Marking (5/22/89) (ANM-114) Provides guidance material for use in demonstrating compliance with the provisions of Part 25 of the FAR requiring floor proximity emergency escape path markings. 25.812-2 Floor Proximity Emergency Escape Path Marking Systems Incorporating Photo luminescent Elements (7/24/97) (ANM-114) Provides guidance for use in demonstrating compliance with the provisions of part 25 of the Federal Aviation Regulations (FAR) regarding floor proximity emergency escape path marking systems (FPEEPMS), which incorporate photo luminescent elements. Although mandatory terms such as “shall” or “must” are used in this AC, because the AC method of compliance is not itself mandatory, these terms apply only to applicants who seek to demonstrate compliance by use of the specific method described by this AC. 25.853-1 Flammability Requirements for Aircraft Seat Cushions (9/17/86) (ANM-110) Provides guidance material for demonstrating compliance with the Federal Aviation Regulations (FAR) pertaining to flammability of aircraft seat cushions. 425.869-1 Electrical System Fire and Smoke Protection (03/25/04) (ANM-100) This Advisory Circular (AC) describes an acceptable means for showing compliance with the requirements of § 25.896(a), “Fire protection: systems,”
of Title 14, Code of Federal Regulations (CFR) part 25. Part 25 contains the airworthiness standards applicable to transport category airplanes. The means of compliance described in this document provides guidance to supplement the engineering and operational judgment that must form the basis of any compliance findings relative to protection of electrical systems from fire and smoke. 25.905-1 Minimizing the Hazards for Propeller Blade and Hub Failures (9/27/00) Describes an acceptable means for showing compliance with the requirements of Section 25.905, “Propellers,” of Title 14, Code of Federal Regulations (CFR) Part 25. It provides guidance on design precautions to take to minimize the hazards that could occur to an airplane if a propeller blade fails or is released by a hub failure. The AC addresses the hazards associated with impact damage. 25.939-1 Evaluating Turbine Engine Operating Characteristics (3/19/86) (ANM-112) Provides guidelines for the evaluation of turbine engine (turbojet, turboprop, and turboshaft) operating characteristics for subsonic transport category airplanes. 25.963-1 Fuel Tank Access Covers (7/29/92) (ANM-112) Sets forth a means of compliance with the provisions of Part 25 of the FAR dealing with the certification requirements for fuel tank access covers on turbine powered transport category airplanes. Guidance information is provided for showing compliance with the impact and fire resistance requirements of Section 25.963(e). 25.981-1B Guidelines for Substantiating Compliance With the Fuel Tank Temperature Requirements (4/18/01) (AIR-110E)
Sets forth some general guidelines for substantiating compliance with fuel tank temperature airworthiness standards section 25.981. 25.981-2 Fuel Tank Flammability Minimization (4-18-01) (ANM-112) Provides information and guidance concerning compliance with the airworthiness standards for transport category airplanes pertaining to minimizing the formation or mitigation of hazards from flammable fuel air mixtures within fuel tanks. This guidance is applicable to transport category airplanes for which a new, amended, or supplemental type certificate is requested. 25.994-1 Design Considerations to Protect Fuel Systems During a Wheel-Up Landing (7/24/86) (ANM-111) Presents guidelines and methods for complying with the requirements of section 25.994 of the Federal Aviation Regulations (FAR). These guidelines pertain to protecting fuel system components located in the engine nacelles and the fuselage from damage which could result in spillage of enough fuel to constitute a fire hazard as a consequence of a wheels-up landing on a paved runway. This material is not mandatory and does not constitute a regulation. 25.1309-1A System Design Analysis (6/21/88) (ANM-112) Describes various acceptable means for showing compliance with the requirements of section 25.1309(b), (c), and (d) of the Federal Aviation Regulations (FAR). These means are intended to provide guidance for the experience engineering and operational judgment that must form the basis for compliance findings. 25.1329-1A Automatic Pilot Systems Approval
(7/8/68) (ANM-110A) Sets forth an acceptable means by which compliance with the automatic pilot installation requirements of FAR 25.1329 may be shown. 25.1357-1 Circuit Protective Device Accessibility (9/20/88) (ANM-111) Describes acceptable means of compliance with the requirements of section 25.1357(d) and (f) of the FAR with respect to the accessibility of circuit protection devices (CPD), such as circuit breakers or fuses. An applicant may elect to use any alternative means found to be acceptable by the FAA for compliance with the FAR. 25.1419-1 Certification of Transport Category Airplanes for Flight in Icing Conditions (8/18/99) (ANM-12) Provides guidance for certification of airframe ice protection systems on transport category airplanes. 25.1435.1, Hydraulic System Certification Tests & Analysis (5/21/01) (ANM-110) This advisory circular (AC) provides guidance material for use as an acceptable means, but not the only means, of demonstrating compliance with the airworthiness standards for transport category airplanes that contain hydraulic system requirements. It is not mandatory and does not constitute a regulation. 25.1455-1 Waste Water/Potable Water Drain System Certification (3/11/85) (ANM-112) Sets forth a specific method of compliance with the requirements of section 25.1455 of the FAR pertaining to draining of fluids through drain masts when the fluids are subject to freezing. This method is designed to verify that draining fluids will not accumulate as ice in sufficient quantity to be hazardous. Is for guidance
purposes and to set forth one method of compliance that has been found acceptable. 25.1457-1A Cockpit Voice Recorder Installations (11/3/69) (ANM-110A) Sets forth one acceptable means of compliance with provisions of FAR 25.1457 (b), (e), and (f) pertaining to area microphones, cockpit voice recorder location, and erasure features. 25.1523-1 Minimum Flight Crew (2/2/93) (ANM-111) Sets forth a method of compliance with the requirements of Section 25.1523 of the FAR, which contains the certification requirements for minimum flight crew on transport category airplanes. 25.1529-1 Instructions for Continued Airworthiness of Structural Repairs on Transport Airplanes (8/1/91) (ANM-112) Provides instructions to ensure continued airworthiness of structural repairs on transport category airplanes. It addresses the approval procedures to follow when making structural repairs to structure certificated under the damage tolerance requirements of Section 25.571 of FAR, Amendment 25-45, and to type designs with Supplemental Inspection Documents, which were based on these criteria. 425. 1533-1 Electronic Equipment and Installations (03/25/04) (ANM-100) Sets forth an acceptable means, but not the only means of demonstrating compliance with the provisions of the airworthiness standards for transport category airplanes related to the electrical equipment and installation. 25.1581-1 Airplane Flight Manual (7/14/97) (ANM-111)
Identifies the information that must be provided in Airplane Flight Manual (AFM) under the airworthiness regulations and provides guidance as to the form and content of the approved portion of an AFM. 27-1B Certification of Normal Category Rotorcraft (9/30/99) (ASW-110) Provides guidance regarding an acceptable means but not the only means of compliance with Part 27 of the Federal Aviation Regulations (FAR) applicable to certification of normal category rotorcraft. This revision renumbers paragraphs to correspond with FAR numbering. Also, it is divided by Subparts and the page numbers reflect the relevant FAR Subpart. SN 050-007-01279-9 29-1 Approval Basis for Automatic Stabilization Equipment (ASE) Installations in Rotorcraft (12/26/63) (AIR-160) Gives means for compliance with flight requirements in various CAR’s. 29-1, Chg. 1 (3/26/64) Transmits revised information about the time delay of automatic stabilization equipment. 29-2C Certification of Transport Category Rotorcraft (9/30/99) (ASW-110) Provides guidance regarding an acceptable means but not the only means of compliance with Part 29 of the Federal Aviation Regulations (FAR) applicable to certification of transport category rotorcraft. This revision renumbers paragraphs to correspond with FAR numbering. Also, it is divided by Subparts and the page numbers reflect the relevant FAR Subpart. SN 050-007-01280-2
33-1B Turbine-Engine Foreign Object Ingestion and Rotor Blade Containment Type Certification Procedures (4/22/70) (ANE-100) Provides guidance and acceptable means, not the sole means, by which compliance may be shown with the design and construction requirements of Part 33 of the Federal Aviation Regulations. 33-2B Aircraft Engine Type Certification Handbook (6/30/93) (ANE-110) Contains guidance relating to type certification of aircraft engines which will constitute acceptable means, although not the sole means, of compliance with the Federal Aviation Regulations. 33-3 Turbine and Compressor Rotors Type Certification Substantiation Procedures (9/9/68) (ANE-100) Sets forth guidance and acceptable means, not the sole means, by which compliance may be shown with the turbine and compressor rotor substantiation requirements in FAR Part 33. 33-4 Design Considerations Concerning The Use Of Titanium In Aircraft Turbine Engines (7/28/83) (ANE-110) Provides guidance and acceptable means, not the sole means, by which compliance may be shown with the design requirements of Part 33 to minimize the probability of the occurrence of an internal fire when titanium is used in aircraft turbine engines.
33-5 Turbine Engine Rotor Blade Containment/Durability (6/18/90) (ANE-110) Provides guidance and acceptable methods, but not the only methods, that may be used by an applicant in showing compliance with the turbine engine rotor blade containment requirements of Part 33 of the Federal Aviation Regulations (FAR). 33-6 Weld Repair of Aluminum Crankcases and Cylinders of Piston Engines (12/20/94) (ANE-110) Provides information and guidance concerning acceptable means, but not the only means, for the development of process specifications for weld repairs on crankcases and cylinders of piston engines. 33.4-1 Instructions for Continued Airworthiness (8/27/99) (ANE-110) Provides guidance on acceptable methods, but not the only methods, of compliance with section 33.4 of the Federal Aviation Regulations, Title 14, Code of Federal Regulations. 33.14-1 Damage Tolerance for High Energy Turbine Motors (1/08/01) This advisory circular describes an acceptable means for showing compliance with the requirements of section 33.14 of the Federal Aviation Regulations (Title 14, Code of Federal Regulations). Section 33.14 contains requirements applicable to the design and life management of high energy rotating parts of aircraft gas turbine engines.
33.15-1 Manufacturing Process of Premium Quality Titanium Alloy Rotating Engine Components (9/22/98) (ANE-110) Provides guidance for compliance with the provisions under Title 14 under the Code of Federal Regulations, Part 33 (14 CFR 33) pertaining to the materials suitability and durability requirements, 33.15, as applicable to the manufacture of titanium alloy high energy rotating parts of aircraft engines. 33.28-1 Compliance Criteria for 14 CFR $33.28, Aircraft Engines, Electrical and Electronic Engine Control Systems (6/29/01) (ANE-110) This advisory circular (AC) provides guidance and acceptable methods, but not the only methods, that may be used to demonstrate compliance with 14 CFR 33.28, Electrical and Electronic Engine Control Systems. Like all AC material, this AC is not, in itself, mandatory and does not constitute a regulation. While these guidelines are not mandatory, they are derived from extensive Federal Aviation Administration (FAA) and industry experience in determining compliance with the pertinent regulations. 433.28-2 Guidance Material for 14 CFR 33.28, Reciprocating Engine, Electrical and Electronic Engine Control Systems (08/13/03) (ANE-110) Provides guidance and acceptable methods, but not the only methods, that may be used by designers of reciprocating engine electronic control systems to demonstrate compliance with §33.28 of Title 14 of the Code of Federal Regulations (14 CFR 33.28), Electrical and electronic engine control systems. 33.47-1 Detonation Testing In Reciprocating Aircraft Engines (6/27/88) (ANE-110) Provides guidance material for acceptable means of demonstrating
compliance with the requirements of FAR Part 33, relating to detonation testing for reciprocating aircraft engines. 433.65-1A Surge and Stall Characteristics of Aircraft Turbine Engines (07/23/03) (ANE-110) Provides guidance material for acceptable means of demonstrating compliance with the requirements of Part 33 of the Federal Aviation Regulations (FAR) relative to surge and stall characteristics and thrust response of turbine engines. These guidelines do not constitute a regulation and are therefore not mandatory. 33.74-92 Turbine Engine Continued Rotation and Rotor Locking (2/14/97) (ANE-110) Provides guidance and acceptable methods, but not the only methods, that may be used to demonstrate compliance with the continued rotation and rotor locking requirements of part 33 of the Federal Aviation Regulations (FARs). 33.78-1 Turbine Engine Power-Loss and Extreme Conditions of Rain and Hail (2/8/00) (ANE-110) Provides guidance and acceptable methods, but not the only methods, that may be used to demonstrate compliance with the requirements contained under Title 14 of the Code of Federal Regulations (14 CFR), part 33, sections 33.78(a)(2) and 33.78(c). 33.83 Turbine Engine Vibration Survey (2/14/97) (ANE-110) Provides information and guidance concerning acceptable means, but not the only means, of compliance with part 33 of the Federal Aviation Regulation (FAR) applicable to vibration tests.
35.37-1A Guidance material for Fatigue Limit Tests and Composite Blade Substantiation (9/17/01) (ANE-110) Provides guidance and describes methods, but not the only methods, for demonstrating compliance with 35.37. The AC also provides methods for the fatigue evaluation of propellers and the fatigue substantiation of composite propeller blades. 435.4-1 Propeller Instructions for Continued Airworthiness (11/03/03) (ANE-110) Provides guidance and acceptable methods, but not the only methods, for demonstrating compliance with 14 CFR §35.4, Instructions for Continued Airworthiness. This AC addresses preparing the instructions for continued airworthiness (ICA) for propellers. 36-1H Noise Levels for U.S. Certificated and Foreign Aircraft (11/15/01) (AEE-110) Provides noise level data for airplanes certificated under FAR Part 36. Noise level data for foreign airplanes certificated to ICAO Annex 16 standards are also provided in a separate appendix for informational purposes. 36-2C Measured or Estimated (Uncertificated) Airplane Noise Levels (2/12/86) (AEE-110) Provides estimates of noise levels or measured noise levels from airplanes not certificated to FAR Part 36. 36-3H Estimated Airplane Noise Levels in A-Weighted Decibels (4/25/02) (AEE-110) Provides listings of estimated airplane noise levels in units of A-weighted sound levels in decibels (dBA), ranked in describing order for the conditions and assumptions described. This
information is provided both for aircraft that have been noise type certificated under 14 CFR Part 36 and for Aircraft for which no such requirement currently exists. 36-4B Noise Certification Handbook (3/23/88) (AEE-3) Promotes uniformity of implementation of the noise certification requirements of Part 36 of the Federal Aviation Regulations (FAR) by presenting technically acceptable test, analysis, and documentation procedures for subsonic turbojet airplanes that may be used by applicants for demonstrating compliance with Part 36. Where appropriate, FAA policy governing such certifications is reviewed. 39-1A Jig Fixtures; Replacement of Wing Attach Angles and Doublers on Douglas Model DC-3 Series Aircraft Airworthiness Directive 66-18-2 (3/5/70) (AFS-340) Describes methods of determining that jig fixtures used in the replacement of the subject attached angles and doublers meet the requirements of Airworthiness Directive 66-18-2. 39-6S Summary of Airworthiness Directives, Announcement of Availability (8/10/98) (AFS-610) Announces the availability of the Summary of Airworthiness Directives 1998 edition in paper, microfiche, and electronic CD-ROM and bulletin board system, and also provides information for ordering these publications. 39-7C Airworthiness Directives (11/16/95) (AFS-340/AFS-613) Provides guidance and information to owners and operators of aircraft concerning their responsibility for complying with airworthiness directives (AD) and recording AD
compliance in the appropriate maintenance records 439-8 Continued Airworthiness Assessments of Powerplant and Auxiliary Power Unit Installations of Transport Category Airplanes (09/08/03) (AIR-110) Describes the Continued Airworthiness Assessment Methodologies (CAAM). The Federal Aviation Administration (FAA) Engine and Propeller Directorate (EPD) and the Transport Airplane Directorate (TAD) may use CAAM to identify unsafe conditions and determine when an “unsafe condition is likely to exist or develop in other products of the same type design” before prescribing corrective action in accordance with Title 14 of the Code of Federal Regulations (14 CFR) part 39. CAAM is used for products associated with the Powerplant or Auxiliary Power Unit (APU) Installations on Transport Category Airplanes. 43-2B Minimum Barometry for Calibration and Test of Atmospheric Pressure Instruments (10/16/80) (AFS-343) Provides guidance material which may be used to determine the adequacy of barometers used in the calibration of aircraft static instruments and presents information concerning the general operation, calibration, and maintenance of such barometers. 43-3A Nondestructive Testing in Aircraft (8/30/00 (AFS-330) Reviews the basic principles underlying nondestructive testing. SN 5007-00208-4. 43-4A Corrosion Control for Aircraft (7/25/91) (AFS-340) Summarizes current available data regarding identification and treatment of corrosive attack on aircraft structure and engine materials. SN 050-007-01044-3. 43-6B
Altitude Reporting Equipment and Transponder System Maintenance and Inspection Practices (8/14/02) (AFS-300) Provides information on acceptable methods of testing altimeters, static systems, altitude encoders, and Air Traffic Control (ATC) transponder systems. 43-7 Ultrasonic Testing for Aircraft (9/24/74) (AFS-310) Describes methods used in ultrasonic nondestructive testing, discusses the many advantages, and points out the simplicity of the tests. Contains many illustrations. SN 050-007-00282-3. 43-9C Maintenance Records (6/8/98) (AFS-340) Describes methods, procedures and practices determined to be acceptable for showing compliance with the general aviation maintenance recordmaking and record-keeping requirements of Title 14 of the Code of Federal Regulations (14 CFR) parts 43 and 91. This material is issued for guidance and outlines several methods of compliance with the regulations. 43-10A Mechanical Work Performed on U.S. and Canadian registered Aircraft (2/25/83) (AFS-340) Provides updated information and guidance to aircraft owners/operators and maintenance personnel concerning mechanical work performed on U.S. registered aircraft by Canadian maintenance personnel and on Canadian registered aircraft by U.S. maintenance personnel and on Canadian registered aircraft by U.S. maintenance personnel. 43-11 Reciprocating Engine Overhaul Terminology and Standards (4/7/76) (AFS-340)
Discusses engine overhaul terminology and standards that are used by the aviation industry.
43-12A Preventive Maintenance (10/28/83) (AFS-340) Provides information concerning preventive maintenance, who may perform it, the standards of performance applicable to it, authority for approving aircraft for return to service, and the applicable recording requirements. It also clarifies those areas most frequently misunderstood in the past, and explains the recent changes in the rules concerning preventive maintenance. 43-14 Maintenance of Weather Radar Radomes (2/24/77) (AFS-350) Provides guidance material useful to repair facilities in the maintenance of weather radomes. 43-15 Recommended Guidelines for Instrument Shops (8/15/77) (AFS-350) Provides guidelines concerning environmental conditions for instrument repair and overhaul shops and information on calibration of test equipment. Provides information on obtaining printed copies of this document or electronic access to it. Provides information on obtaining printed copies of this document or electronic access to it. 43-16A Aviation Maintenance Alerts. (9/3/99) (AFS-640) Issued monthly, the Aviation Maintenance Alerts are prepared from information submitted by persons who operate and maintain civil aeronautical products. The Alerts provide a uniform means through which safety and service experience may be interchanged. The intent of this publication is to improve safety and service reliability of aeronautical products.
43-17 Methods, Techniques, and Practices Acceptable to the Administrator Governing the Installation, Removal, or Changes of Identification Data and Identification Plates (9/5/79) (AFS-340) Provides information and guidance concerning the installation, removal, or change of identification data and identification plates on aircraft, aircraft engines, propellers, and propeller blades and hubs. 43-204 Visual Inspection for Aircraft (8/14/97) (AFS-310) Provides technical information to persons conducting a visual inspection of aircraft. The procedures presented in this AC are an acceptable means, but not the only means, for conducting visual inspections and inspection programs. 43-205 Guidance for Selecting Chemical Agents and Process for Depainting and General Cleaning of Aircraft and Aviation Products (9/25/98) (AFS-340) Describes an acceptable means, but not the only means,, for selecting and testing alternatives to chemical agents and/or processes currently required by some manufacturers’ maintenance instructions, including instructions for continuing airworthiness. 43-206 Inspection, Prevention, Control, and Repair of Corrosion on Avionics Equipment (5/30/01) (AFS-304) AC contains acceptable methods, techniques, and practices for inspection, prevention, control and repair of corrosion on avionic systems and equipment. 443-207 Correlation, Operation, Design, and Modification of Turbofan/Jet Engine Test Cells (12/26/02) (AFS-340) Provides guidance regarding test cell correlation procedures for test cells
used for in-service acceptance testing of turbofan and turbojet engines. This AC discusses the effects of the design, operation, and modification of a test cell and engine test hardware on engine performance. The AC also provides guidance on conducting, evaluating, and maintaining test cell correlation. Like all advisory material, this AC is not in itself mandatory and does not constitute a regulation. The Federal Aviation Administration (FAA) issues it to describe an acceptable means, but not the only means, for correlating and maintaining a satisfactory correlation status of a test cell. 443-208 Maintenance of Emergency Evacuations Systems for Aircraft Operating Under Part 121 (04/04/03) (AFS-300) Provides information and guidance for the maintenance of emergency evacuation systems (EES) used on aircraft operating under the provisions of Title 14 of the Code of Federal Regulations (14 CFR) part 121. Additionally, this AC discusses the responsibilities and means of compliance for the air carrier and persons performing maintenance. 443-209 L-39 Albatross Military Jet Recommended Inspection Program (10/16/03) (AFS-300) Provides a recommended inspection program for existing and new owners of L-39 Albatross aircraft operating under an Experimental Exhibition Special Airworthiness Certificate. While this AC provides one way of addressing the inspection and overhaul provisions found on the aircraft’s operating limitations, it may not be the only way of addressing the requirements for continued airworthiness of L-39 aircraft. This AC is not meant to supersede existing L-39 inspection programs.
443-210 Standardized Procedures for Requesting Field Approval of Data, Major Alterations, and Repairs Describes standardized procedures for requesting field approvals for certificated products. It describes the field approval process, data that supports making an alteration or repair, and the purpose and uses of the Aircraft Flight Manual Supplements (AFMS) and Instructions for Continued Airworthiness (ICA). This AC also gives instructions for completing the Field Approval Checklist and shows a sample Compliance Checklist format. 43.9-1E Instructions for Completion of AA Form 337 (OMB No. 2120-0020), Major Repair and Alteration (Airframe, Powerplant, Propeller, or Appliance) (5/21/87) (AFS-340) Provides instructions for completing FAA Form 337, Major Repair and Alteration (Airframe, Powerplant, Propeller, or Appliance). 43.13-1B Acceptable Methods, Techniques and Practices--Aircraft Inspection and Repair (9/8/98) (AFS-610) Contains methods, techniques, and practices acceptable to the Administrator for inspection and repair of nonpressurized areas of civil aircraft only when there are no manufacturer repair or maintenance instructions. Chg 1 (12/7/01) SN050-007-01227-6 43.13-1B, Chg1 (12/7/01) SN050-007-01318-3 43.13-2A Acceptable Methods, Techniques, and Practices Aircraft Alterations (Includes Chg. 1). (6/9/77) (AFS-340) Contains methods, techniques, and practices acceptable to the Administrator for use in altering civil aircraft.
SN 050-007-00625-0. 43.13-2A, Chg. 2 (10/30/89) SN 050-007-00848-1. 45-2A Identification and Registration Marking (4/16/92) (AIR-230) Provides guidance and information concerning the identification and marking requirements of Federal Aviation Regulations (FAR) Part 45, and describes an acceptable means, but not the sole means, of compliance with the regulations. 45-3 Installation, Removal, or Change of Identification Data and Identification Plates on Aircraft Engines, (11/6/85) (AIR-200) Provides information and guidance concerning the installation, removal, or change of identification data and identification plates on aircraft engines, and identifies an acceptable means, but not the only means, of compliance with FAR Part 45.
Airmen
Subject No. 60
60-4A Pilot’s Spatial Disorientation (2/9/83) (AFS-840) Acquaints pilots with the hazards of disorientation caused by loss of visual reference with the surface. 60-6B Airplane Flight Manuals (AFM), Approved Manual Materials, Markings, and Placards Airplanes (9/25/80) (AFS-820) Calls attention to the regulatory requirements relating to the subject and provides information to aid pilots to comply with these requirements. 60-11C Test Aids and Materials That May Be Used by Airman Knowledge Testing Applicants
(4/26/99) (AFS-630) Provides information concerning test aids and materials that may be used by applicants taking airman knowledge tests. 60-22 Aeronautical Decision Making (12/13/91) (AFS-800) Provides introductory material, background information, and reference material on aeronautical decision making. Provides a systematic approach to risk assessment and stress management in aviation, illustrates how personal attitudes can influence decision 60-25E Reference Materials and Subject Matter Knowledge Codes for Airman Knowledge Testing (4/16/01) (AFS-630) Appendixes 1 and 2 contain the latest list of reference materials and subject matter knowledge codes for airman knowledge testing. 60-26B Announcement of Availability: Flight Standards Service Airman Training and Testing Information (6/8/00) (AFS-630) Provides Flight Standards Service on airman training and testing materials website information. The airman certification knowledge and skill testing information is critical to flight safety and comprises the FAA’s standards for airman certification testing. 60-28 English Language Skill Standards Required by 14 CFR Parts 61,63, and 65 (9/23/97) (AFS-630) Provides guidance for airman applicants, training organizations, designated examiners, and aviation safety inspectors in determining English language skills required for airman certification under Title 14 of the Code of Federal Regulations (14 CFR) parts 61,63 and 65.
60-29 Renumbering of Airman Training and Testing Publications (2/1/99) (AFS-630) Announces the renumbering of airman training and testing materials published by the Airman Testing Standards Branch, AFS-630, Oklahoma City, OK. 61-9B Pilot Transition Courses for Complex Single Engine and Light Twin-Engine Airplanes (1/15/74) (AFS-630) A guide to the procedures and standards to be followed for a thorough and comprehensive checkout in modern single- and twin-engine aircraft. SN 050-007-00226-2 61-10A Private and Commercial Pilots Refresher Courses (9/27/72) (AFS-630) Provides a syllabus of study requirements and describes the areas of training that should be emphasized. SN 050-011-00060-7 61-23C Pilot’s Handbook of Aeronautical Knowledge (7/10/97) (AFS-630) Provides basic knowledge that is essential for pilots. Introduces pilots to the broad spectrum of knowledge that will be needed as they progress in their pilot training. Except for the Code of Federal Regulations pertinent to civil aviation, most of the knowledge areas applicable to pilot certification are presented. This handbook is useful to beginning pilots, as well as those pursuing more advanced pilot certificates. SN 050-011-00078-1. 61-65D Certification: Pilot and Flight Instructors and Ground Instructors (9/20/99) (AFS-840)
Provides guidance for pilots and flight instructors on the certification standards, written test procedures, and other requirements contained in FAR Part 61. 61-67C Stall Spin Awareness Training (9/25/00) (AFS-840) Explains the stall and spin awareness training required under FAR Part 61 and offers guidance to flight instructors who provide that training. Informs pilots of the airworthiness standards for the type certification of small airplanes prescribed in FAR 23.221 concerning spin maneuvers and emphasizes the importance of observing restrictions which prohibit the intentional spinning of certain airplanes. 61-83E Nationally Scheduled FAA- Approved Industry-Conducted Flight Instructor Refresher Clinics (FIRC) (11/19/01) (AFS-840) Provides guidance for the preparation of training course outlines (TCO) for FAA-approved industry conducted FIRC’s under Amendment 61-25 to the FAR, which was adopted 4/13/94. 61-84B Role of Preflight Preparation (3/18/85) (AFS-840) Modifies and updates the flight information available to pilots as a result of changes in the basic Airmen Information Manual format. 61-89E Pilot Certificates: Aircraft Type Ratings (8/4/00) (AFS-840) Provides a generic type rating curriculum that may serve as a basis for schools to develop a training requirements of Federal Aviation Regulations Parts 61 and 141. 61-91H Pilot Proficiency Award Program (4/26/96) (AFS-800)
Expands the Pilot Proficiency Award Program to 20 phases and makes special provision for seaplane-rated pilots to obtain “seawings.” 61-94 Pilot Transition Course For Self- Launching Or Powered Sailplanes (Motorgliders) (7/31/84) (AFS-840) Provides recommendations, but is not the only means, that may be used by glider pilots who desire to transition into sailplanes or gliders with selflaunching capability. 61-98A Currency and Additional Qualification Requirements for Certificated Pilots (3/26/91) (AFS-840) Provides information for certificated pilots and flight instructors to use in complying with flight review required by FAR Section 61.56, the recent flight experience requirements of FAR Section 61.57, and the general limitations contained in FAR Section 61.31(d), (e), and (g). It also provides guidance regarding transition to other makes and models of aircraft. 461-107A Operations of Aircraft at Altitudes Above 25,000 Feet MSL and/or MACH numbers (Mmo) Greater Than .75 (01/02/2003) (AFS-820) Alerts pilots transitioning to complex, high-performance aircraft which are capable of operating at high altitudes and high airspeeds of the need to be knowledgeable of the special physiological and aerodynamic considerations involved within this realm of operations. 61-111A Announcement of Availability: FAA-S-8081-4C, Instrument Rating Practical Test Standards (PTS) for Airplane, Helicopter, Power Lift (12/15/98) (AFS-630) Provides information on obtaining printed copies of this document or electronic access to it.
61-118A Announcement of Availability: FAA-S-8081-14, Private Pilot Practical Test Standards (Airplane) (3/1/99) (AFS-630) Provides information on obtaining printed copies of this document or electronic access to it 61-121 Announcement of Availability: FAA-S-8081-10A, Aircraft Dispatcher Practical Test Standard (5/17/95) (AFS-630) Announces availability of this publication from the Superintendent of Documents. 61-122D Announcement of Availability: FAA-S-8081-5D, Airline Transport Pilot and Aircraft Type Rating PTS for Airplane, (2/9/01) (AFS-630) Provides information on obtaining printed copies of this document or electronic access to it. 61-123 Announcement of Availability: Practical Test Standards (Rotorcraft) FAA-S-8081-7A, FAA- S-8081-15, FAA-S-8081-16 (3/5/96) (AFS-630) Announces the availability of FAA-S- 8081-7A, Flight Instructor Practical Test Standards for Rotorcraft; FAA-S- 8081-15, Private Pilot Practical Test Standards for Rotorcraft; FAA-S-8081- 16, Commercial Pilot Practical Test Standards for Rotorcraft; and, provides information on obtaining printed copies or electronic access to these documents. 61-124 Announcement of Availability: FAA-S-8081-17, Private Pilot Practical Test Standards for Lighter-Than-Air (Balloon/Airship) (5/15/96) (AFS-630) Announces the availability of FAA-S-8081-17, Private Pilot Practical Test Standards for Lighter-Than-Air (Balloon/Airship), and provides
information on obtaining printed copies or electronic access to this document. 61-125 Announcement of Availability: Commercial Pilot Practical Test Standards: FAA-S-8081-18 and FAA-S-8081-12A, (4/30/97) (AFS-630) Announces the availability of FAA-S-8081-18, Commercial Pilot Practical Test Standards for Lighter- Than-Air, and FAA-S-8081-12A, Commercial Pilot Practical Test Standards for Airplane; and provides information on obtaining printed copies or electronic access to these documents. 61-126 Qualification and Approval of Personal Computer-Based Aviation Training Devices (5/12/97) (AFS-840) Provides information and guidance to potential training device manufacturers and aviation training consumers concerning a means, acceptable to the Administrator, by which personal computer-based aviation training devices (PCATD) may be qualified and approved for flight training toward satisfying the instrument rating training under the provisions of 14 CFR parts 61 and 141. 61-127A Announcement of Availability: FAA-S-8081-19, Recreational Pilot Powered Parachute Practical Test Standard (5/9/01) (AFS-630) Announces the availability of FAA-S-8081-19, Recreational Pilot Powered Parachute Practical Test Standard and provides information on obtaining printed copies or electronic access. 61-128 Announcement of Availability: FAA-S-8081-6A, Flight Instructor Practical Test Standard for Airplane, with Change 1
(4/13/98) (AFS-630) Announces the availability of the reprint of FAA-S-8081-6A, Flight Instructor Practical Test Standards for Airplane (Single-Engine and Multiengine) with Change 1, and provides information for obtaining printed copies or electronic access. 61-129 Announcement of Availability: FAA-S-8081-20, Airline Transport Pilot Aircraft Type Rating PTS for Helicopter (8/12/98) (AFS-630) Announces the availability of FAA-S-8081-20, Airline Transport Pilot and Aircraft Type Rating Practical Test Standards for Helicopter, from the Superintendent of Documents, and provides information on obtaining printed copies or electronic access. 61-130 Announcement of Availability: FAA-S-8081-8A, Flight Instructor Practical Test Standards for Glider (4/26/99) (AFS-630) Provides information on obtaining printed copies of this document or electronic access to it. 61-131 Announcement of Availability: FAA-S-88081-22, Private Pilot Practical Test Standards for Gliders (4/26/99) (AFS-630) Provides information on obtaining printed copies of this document or electronic access to it. 61-132 Announcement of Availability: FAA- S-8081-23, Commercial Pilot Practical Test Standards for Glider (4/26/99) (AFS-630) Provides information on obtaining printed copies of this document or electronic access to it.
61-133B Announcement of Availability: FAA- S-8081-9B, Flight Instructor Instrument Practical Test Standards for Airplane and Helicopter (5/9/01) (AFS-600) Provides information on obtaining copies or electronic access of this document. 61-134 General Aviation Controlled Flight into Terrain Awareness (04/01/03) (AFS-800) Highlights the inherent risk that controlled flight into terrain (CFIT) poses for general aviation (GA) pilots. This AC includes the Federal Aviation Administration's (FAA) common definition of the term CFIT, identifies some, but not all, of the risks associated with GA CFIT accidents, and provides some recommendations and strategies to combat CFIT within the GA community. This AC is not an all-inclusive document on CFIT; rather, this AC is designed to help flight instructors, FAA Aviation Safety Program Managers, and other trainers develop CFIT training materials by identifying some of the factors involved in GA CFIT accidents. 63-2 Announcement of Availability: FAA-S-8081-21, Flight Engineer Practical Test Standards (3/1/99) (AFS-630) Provides information on obtaining printed copies of this document or electronic access to it. 65-5B Parachute Rigger Senior/Mastercertification Guide (7/25/88) (AFS-630) Provides information to persons interested in becoming certificated parachute riggers. Provides information on how to apply for a parachute rigger certificate and ratings, and assists the applicant in preparing for the written, oral, and practical tests. SN 050-007-00805-8
65-9A Airframe and Powerplant Mechanics--General Handbook (4/12/76) (AFS-640) Designed as a study manual for persons preparing for a mechanic certificate with airframe or powerplant ratings. Emphasis in this volume is on theory and methods of application, and is intended to provide basic information on principles, fundamentals, and airframe and powerplant ratings. SN 050-007-00379-0 . 65-9A, Chg. 1 (6/16/99) (AFS-640) This change accommodates NTSB’s Safety Recommendation A-96-37. The “spot test” procedure that distinguishes between Inconel and stainless steel is replaced with an “electrochemical” procedure. SN 050-007-01255-1 65-12A Airframe and Powerplant Mechanics Powerplant Handbook (4/12/76) (AFS-640) Designed to familiarize student mechanics with the construction, theory of operation, and maintenance of aircraft powerplants. SN 050-007-00373-1 65-13X FAA Inspection Authorization Directory (9/9/03) (AFS-640) Transmits a directory all certificated mechanics who held an inspection authorization as of September, 2003. SN 050-007-01341-8 65-15A Airframe and Powerplant Mechanics Airframe Handbook (4/12/76) (AFS-640) Designed to familiarize student mechanics with airframe construction, repair, and the operating theory of airframe systems. SN 050-007-00391-9 65-23A
Certification of Repairmen (Experimental Aircraft Builders) (7/22/87) (AFS-340) Provides guidance to builders of experimental aircraft concerning certification as repairmen. 65-24 Certification Of A Repairman (General) (2/1/83) (AFS-350) Provides information and guidance to the aviation public on the procedures for certification of a repairman. 65-25B Aviation Maintenance Technician Awards Program (8/26/99) (AFS-300) Outlines and upgrades the requirements for participation in the Federal Aviation Administration’s Aviation Maintenance Technician Awards Program. 65-26B Charles Taylor “Master Mechanic Award” (7/20/98) (AFS-340) Presents changes to the Charles Taylor “Master Mechanic” award. This FAA award recognizes aviation maintenance personnel who have at least 50 years of experience in the aviation maintenance industry. The award is named for Charles Taylor, the mechanic who maintained the Wright Brothers airplane. 65-30A Overview of the Aviation Maintenance Profession (11/09/01) (AFS-305) To provide information to prospective airframe and powerplant mechanics and other persons interested in the certification requirements, application procedures, and the mechanic written, oral, and practical tests. 65-31 Training Qualification, and Certification of Non-Destructive Inspection (NDI) Personnel (10/4/01)
Consolidated directory of FAA Certificated technical Personnel Examiners designated under the authority of Title 14 of the Code of Federal Regulations (14CFR) Part 183, and is current as of August 29, 2001
Airspace
Subject No. 70
70/7460-1K Obstruction Marking and Lighting (2/3/00) (ATA-411) Describes the FAA standards for marking and lighting structures to promote safety. 70/7460-1K, Chg 1 (4/15/00) 70/7460-2K Proposed Construction or Alteration of Objects that May Affect the Navigable Airspace (ATA-400) Provides information to persons proposing to erect or alter an object that may affect the navigable airspace. Explains the need to notify FAA before construction begins and FAA’s response to those notices as required by FAR 77. 73-2 IFR Helicopter Operations in the Northeast Corridor (6/11/79) (ATF-4) Advises interested users of special Area Navigation (RNAV) helicopter routes between Washington, DC, and Boston, Massachusetts, (known as the “Northeast Corridor”) and provides guidelines to operators for the safe use of these routes. The use of these routes is voluntary.
Air Traffic Control and
General Operations
Subject No. 90
90-23F Aircraft Wake Turbulence
(2/20/02) (AFS-430) Alerts pilots to the hazards of aircraft wake turbulence and recommends related operational procedures. 90-34 Accidents Resulting from Wheelbarrowing In Tricycle Gear Equipped Aircraft (2/27/68) (AFS-840) Explains “wheel barrowing”, the circumstances under which it is likely to occur, and recommended corrective action. 90-42F Traffic Advisory Practices at Airports Without Operating Control Towers (5/21/90) (AFS-820) Contains good operating practices and procedures for use when approaching or departing airports without an operating control tower and airports that have control towers operating part time. Includes changes in radio frequencies and phraseology. 90-45A Approval of Area Navigation Systems for Use in the U.S. National Airspace System (Consolidated Reprint includes Changes 1 and 2) (2/21/75) (AFS-400) Provides guidelines for implementation of two-dimensional area navigation (2D RNAV) within the U.S. National Airspace System (NAS). Provides for both VOR/DME dependent systems and self-contained systems such as Inertial Navigation Systems (INS). 90-48C Pilots’ Role in Collision Avoidance (3/18/83) (AFS-820) Alerts all pilots to the potential hazards of midair collision and near midair collision, and to emphasize those basic problem areas related to the human causal factors where improvements in pilot education, operating practices, procedures, and improved scanning techniques are needed to reduce midair conflicts.
90-50D Requirements for 760-Channel VHF Radio for Aeronautical Operations (4/9/92) (ASR-520) Encourages aircraft owners to upgrade their air-ground radio communication systems. Describes and upgrades civil air traffic control frequencies in the very high frequency (118.000 to 136.975 MHz) band. The 136.000 to 136.975 MHz band became available for aeronautical use on January 1, 1990. 90-58C VOR Course Errors Resulting from 50 kHz channel Mis-Selection (4/7/75) (AFS-310) Provides information concerning a potentially hazardous situation when a 200 channel VOR receiver is inadvertently mistuned by 50 kHz from the frequency of a 100 kHz ground station. 90-66A Recommended Standard Traffic Patterns and Practices for Aeronautical Operations at Airports without Operating Control Towers (8/26/93) (AFS-820) Calls attention to regulatory requirements and recommended procedures for aeronautical operations at airports without operating control towers. It recommends traffic patterns and operational procedures for aircraft, lighter than air, glider, parachute, rotorcraft, and ultra-light vehicle operations where such use is not in conflict with existing procedures in effect at those airports. 90-67B Light Signals from the Control Tower for Ground Vehicles, Equipment, and Personnel (8/25/94) (ATP-129) Provides the aviation community with the meaning of the light signals used when communicating with ground vehicles, equipment, and personnel on the airport movement area from the control tower.
90-75 Strobe Light System Inspection Practices (2/10/77) (AFS-310) Advises the general aviation community of the importance of proper maintenance of capacitive discharge strobe light systems which are installed within or near fuel systems. 90-79 Recommended Practices and Procedures for the Use of Electronic Long-Range Navigation (7/14/80) (AFS-400) Presents recommended operational practices and procedures for the use of electronic long-range navigation equipment in oceanic or remote land areas. 90-80B Approval of Offshore Standard Approach Procedure (OSAP), Airborne Radar Approaches (ARA), and Helicopter En Route Areas (HEDA) Criteria (4/12/99) (AFS-420) Provides criteria and describes methods for obtaining to use Offshore Standard Approach Procedures, Airborne Radar Approaches, and Helicopter Enroute Areas. 90-89A Amateur-Built Aircraft Flight Testing Handbook (5/24/95) (AFS-340) Provides suggestions and safety-related recommendations to assist amateur and ultra-light builders in developing individualized aircraft flight test plans. It includes flight testing recommendations for canard-type and ultra-light aircraft. SN 050-007-01087-7 490-91G North American Route Program (05/08/03) (ATT-1) Provides guidance to users of the National Air Space System for participation in the North American Route Program (NRP).
90-92 Guidelines for the Operational Use of Loran-C Navigation Systems Outside the U.S. NAS (2/5/93) (AFS-430) Contains guidance to be used by pilots for the operational use of Loran-C navigation systems under visual flight rules and instrument flight rules while operating outside the U.S. NAS and beyond the coverage of standard International Civil Aviation Organization navigation aids. These navigation aids include very high frequency omnidirectional beacons. Also contains guidance which is applicable for use while over the Gulf of Mexico and other coastal waters. 90-92, Chg. 1 (6/15/93) 90-93A Operating Procedures for Airport Traffic Control Towers (ATCT) That Are Not Operated by, or Under Contract with, the United States (Non-Federal) (11/15/99) (ATP-40) Recommends publications, administrative and operational procedures that will assist in the management of a non-federal ATCT (NFCT). 90-94 Guidelines for Using GPS Equipment for IFR En Route & Terminal Operations & for Nonprecision Instrument Approaches in the U.S. National Airspace System (12/14/94) (AFS-820) Contains guidance for pilots to use Global Positioning System (GPS) equipment during instrument flight rules navigation. Emphasis is placed on the GPS approach overlay program. 90-95 Unanticipated Right Yaw in Helicopters (12/26/95) (AFS-800) Examines the unanticipated right yaw phenomenon, the circumstances under
which it may be encountered, how it can be prevented, and how the pilot should react if it is encountered. 90-96 Approval of U.S. Operators and Aircraft to Operate Under IFR in European Airspace Designated for Basic Area Navigation (BRNAV/RNP-5) (3/20/98) (AFS-430) Provides guidance regarding on-board Area Navigation (BRNAV) equipment requirements for operators of U.S. registered civil aircraft, operating in a Basic Area Navigation (BRNAV) environment in the European region. 90-97 Use of Barometric Vertical Navigation (VNAV) for Instrument Approach Operations using Decision Altitude (10/19/00) (AFS-420) Provides guidance for the operational use of vertical navigation (VNAV) equipment to perform CFR Part 97 area navigation (RNAV) instrument approach procedures published with a VNAV Decision Altitude (DA). This Advisory Circular identifies the types of equipment that the Federal Aviation Administration (FAA) has determined to be acceptable for VNAV) approach procedures. 490-98 Chg. 1 Simultaneous Closely Spaced Parallel Operations at Airports Using Precision Runway Monitor (PRM) Systems (10/06/03) (ATP-120) Notify pilots and operators about the establishment of specific air traffic procedures to conduct flight operations into airports identified for simultaneous closely-spaced parallel approaches using PRM systems. 490-99 High Altitude Airspace Redesign Phase 1(ATA-301) (09/22/03) Describes the National Airspace Redesign (NAR) program to redesign high altitude airspace, High Altitude
Redesign (HAR), and provide recommended processes for flight planning and operations in the first segment of the redesigned airspace during Phase 1. 91-6A Water, Slush, and Snow on the Runway (5/24/78) (AFS-430) Provides background and guidelines concerning the operation of turbojet aircraft with water, slush, and/or snow on the runway. 91-13C Cold Weather Operation of Aircraft (7/24/79) (AFS-820) Provides background and guidelines relating to operation of aircraft in the colder climates where wide temperature changes may occur. 91-14D Altimeter Setting Sources (4/9/79) (AFS-340) Provides the aviation public and industry with guidelines for setting up reliable altimeter setting sources. 91-16 Category II Operations General Aviation Airplanes (8/7/67) (AFS-820) Sets forth acceptable means by which Category II operations may be approved in accordance with FAR Parts 23, 25, 61, 91, 97, and 135. 91-22A Altitude Alerting Devices/Systems (12/23/71) (AFS-400) Provides guidelines for designing, installing, and evaluating altitude alerting systems. 91-26 Maintenance and Handling of Air- Driven Gyroscopic Instruments (10/29/69) (AFS-310) Advises operators of general aviation aircraft of the need for proper maintenance of air-driven gyroscopic instruments and associated air filters.
91-33A Use of Alternate Grades of Aviation Gasoline for Grade 80/87 and Use of Automotive Gasoline (7/18/84) (ANE-110) Provides information relating to the use of alternate grades of gasoline when grade 80/87 aviation is not available and the resultant effects of the use of the alternate fuels which have higher TEL (tetraethyl lead) content. Suggestions are offered as acceptable means of avoiding engine operating difficulties when using alternate fuels. This circular also provides suggestions for added safety in the use of automotive gasoline in those aircraft engines and aircraft covered by Supplemental Type Certificates (STCs). 91-35 Noise, Hearing Damage, and Fatigue in General Aviation Pilots (3/28/72) (AAM-620) Acquaints pilots with the hazards of regular exposure to cockpit noise. Especially pertinent are piston-engine, fixed-wing, and rotary-wing aircraft. 91-36C VFR Flight Near Noise-Sensitive Areas (10/19/84) (ATA-300) Encourages pilots making VFR flights near noise-sensitive areas to fly at altitudes higher than the minimum permitted by regulation and on flight paths, which will reduce aircraft noise in such area. 91-37A Truth in Leasing (1/16/78) (AFS-820) Provides information and guidance for lessees and conditional buyers of U.S. registered large civil aircraft. If you are planning to charter an airplane take a moment to learn about chartered and leased aircraft.
91-38A Large and Turbine-Powered Multiengine Airplanes, Part 91, Subpart D (11/27/78) (AFS-340) Sets forth guidelines and procedures to assist operators of large and turbinepowered multiengine airplanes in meeting the safety requirements of FAR, Part 91, Subpart D. 91-42D Hazards of Rotating Propeller and Helicopter Rotor Blades (3/3/83) (AFS-310) Updates statistical information on propellers-and rotor-to-person accidents and offers suggestions to reduce the frequency of such accidents. 91-43 Unreliable Airspeed Indications (6/26/75) (AFS-223) Alerts pilots to the possibility of erroneous airspeed/Mach indications that may be caused by blocking or freezing of the pilot system and advises of corrective action that can be taken. 91-44A Operational and Maintenance Practices for Emergency Locator Transmitters and Receivers (12/12/80) (AIR-120) Combines and updates material in several Advisory Circulars on the subject of emergency locator transmitters (ELT) receivers for airborne service. 91-45C Waivers: Aviation Events (2/1/90) (AFS-810) Provides prospective aviation event sponsors and other interested parties with information necessary to assist in planning and conducting a safe aviation event. In addition, it provides information on the application process for a certificate of Waiver or Authorization.
91-46 Gyroscopic Instruments. Good Operating Practices (2/4/77) (AFS-350) Issued to re-emphasize to general aviation instrument-rated pilots the need to determine the proper operation of gyroscopic instruments, the importance of instrument crosschecks and proficiency in partial-panel operations. 91-48 Acrobatics--Precision Flying With a Purpose (6/29/77) (AFS-820) Provides information to persons who are interested in acrobatic flying to improve their piloting skills as recreation, sport, or as a competitive activity. 91-49 General Aviation Procedures for Flight in North Atlantic Minimum Navigation Performance Specifications Airspace (8/23/77) (AFS-820) Sets forth acceptable means, but not the only means, of obtaining authorization to operate within specified airspace over the North Atlantic, designated as the NAT (North Atlantic) MNPS (Minimum Navigation Performance Specifications) airspace, after 0001 Greenwich Mean Time, Dec. 29, 1977. This requirement applies to persons operating under FAR Part 91 and for FAR Part 135 certificate holders, except those operating under Section 135.2. 91-49, Chg. 1 (2/6/78) 91-50 Importance of Transponder Operation and Altitude Reporting (8/24/77) (AFS-820) Provides information and guidance concerning the importance of transponder operation and altitude reporting in the National Airspace System.
91-51A Effect of Icing on Aircraft Control and Airplane Deice and Anti-Ice Systems (7/19/96) (AFS-820) Provides information for pilots regarding the hazards of aircraft icing and the use of airplane deice and antiice systems. 91-53A Noise Abatement Departure Profile (7/22/93) (AFS-430) Describes acceptable criteria for safe noise abatement departure profiles (NADP) for subsonic turbojet-powered airplanes with a maximum certificated gross takeoff weight of more than 75,000 pounds. These procedures provide the user with one means, although not the only means, of establishing acceptable NADP’s. These departure profiles are consistent with the airworthiness standards required by the Federal Aviation Regulations Part 25 for type certification and Part 91 for general airplane operations. 91-54 Automatic Reporting Systems-- Altimeter Setting and Other Operational Data (2/26/79) (AFS-820) Provides guidelines for the development and installation of automatic reporting systems for altimeter setting and other operational data intended for use in connection with IFR operations. 91-55 Reduction of Electrical System Failures Following Aircraft Engine Starting (10/28/80) (AFS-310) Warns general aviation aircraft owner/pilots and maintenance personnel of possible total electrical system failure following aircraft engine starting. 91-56A Program For Large Transport Category Airplanes (4/29/98) (ANM-115)
Provides guidance material to manufacturers and operators of transport category airplanes for use in developing a continuing structural integrity program to ensure safe operation of older airplanes throughout their operational lives. This guidance material applies to large transport airplanes which were certified under the fail-safe and fatigue requirements of Civil Air Regulations (CAR) 4b o 14 CFR part 25 of the Federal Aviation Regulations (FAR), prior to Amendment 25-45, and which have a maximum gross weight greater than 75,000 pounds. Guidance material on this subject for other transports is provided in AC 91-60. The procedures set forth by this AC are applicable to the large transport category airplanes operated under Subpart D of part 91, and parts 121 and 125. 91-57 Model Aircraft Operating Standards (6/9/81) (AFS-820) Outlines, and encourages voluntary compliance with, safety standards for model aircraft operators. 91-58A Use of Pyrotechnic Visual Distress Signaling Devices in Aviation (2/10/00) (AFS-820/AFS-630) Suggests standards and procedures for the acquisition, use, and storage of pyrotechnic visual distress signaling devices that are intended for use in aircraft emergencies. 91-59 Inspection and Care of General Aviation Aircraft Exhaust Systems (8/20/82) (AFS-340) Emphasizes the safety hazards of poorly maintained single-engine aircraft exhaust systems (reciprocating powerplants) and highlights points at which exhaust system failures occur. Further, it provides information on the kind of problems to be expected and recommends the performance of ongoing preventive maintenance and maintenance by pilots and mechanics, respectively.
Continue reading ↓ 120 of 235 passages shown